West Mountain Radio | RIGrunner 4005i | Technical information | West Mountain Radio RIGrunner 4005i Technical information

West Mountain Radio RIGrunner 4005i Technical information
34
DC Power & Accessories
ASR-SL-11R
AME-SPS-75MV
75 Amp Switching
Power Supply
This power supply provides 75 amps continuous
output current—ideal for use the with Ameritron’s
ALS-500M 500 watt solid state amplifier. It has less
than 100 mV peak-to-peak ripple under full load.
Load regulation is better than 1.5% under full load.
Other features include reverse-polarity protection,
brownout input protection, over-current/overtemperature protection, and a thermally-controlled
quiet fan. Output voltage is variable with metering for
both voltage and current.
• Input: 108-132 Vac, 50/60 Hz
• Current Draw: 11 Amps
AME-SPS-75MV
75 Amp Switching Power Supply .......................................$244.95
GZV4000 and GZV6000
Switching Mode Power Supplies
The GZV4000 provides a variable voltage
output from 5 to 15 Vdc at 40 amps, while its
higher-rated counterpart the GZV6000 gives you
1 to 15 Vdc at 60 amps.
These versatile power supplies look great and offer you rock-solid performance.
The attractive front panel includes a selectable meter with post, snap-on and cigarette
lighter outputs. The voltage control knob has a center 13.5 Vdc detent for precise
adjustability. A built-in 8 Watt speaker makes these power supplies a versatile addition
to your shack’s setup.
DMN-GZV4000
Switching Mode Power Supply 40A ................................... $169.95
DMN-GZV6000
Switching Mode Power Supply 60A ................................... $369.95
SL Series Power Supplies
These low-profile linear supplies
are internally adjustable to deliver 11 to 15 Vdc. They’re electronically
regulated, and feature over-voltage and current limiting protection.
Part Number
Description
ASR-SL-11A
ASR-SL-11R
ASR-SL-11XLR
ASR-SL-15R
Power Supply with Fused Cord
Power Supply
Power Supply, 4-Pin XLR Port
Power Supply
Amps
Continuous/Peak
7A/11A at 13.8 Vdc
7A/11A at 13.8 Vdc
7A/11A at 13.8 Vdc
12A/15A at 13.8 Vdc
ASR-SL-11R
Price
$94.95
$104.95
$122.95
$137.95
VLS Series
Power Supplies
With an adjustable output voltage from 5 to 32 volts,
these power supplies can provide DC power to a wide
range of shack gear. They feature front-panel adjustable
output controls, making them great bench “test” power supplies. These
supplies are also great solutions if you have unique voltage requirements.
Part Number
ASR-VLS-10M
ASR-VLS-25M
ASR-VLS-35M
Description
Supply with Dual Meters
Supply with Dual Meters
Supply with Dual Meters
Amps
Continuous/Peak
8A/10A at 28 Vdc
18A/25A at 28 Vdc
27A/35A at 28 Vdc
ASR-VLS-10M
Price
$172.95
$336.95
$392.95
Compact DC
Power Supplies from MFJ
These are the perfect
supplies for portable and
QRP operation. They are small
enough to carry in briefcases
or backpacks.
MFJ’s 4115 Power Supply weighs a shade over one and a half
pounds and easily fits into your suitcase. It can power most VHF/UHF or
QRP radios while offering over-voltage and over-current protection. Hookup is via 5-way
binding posts. It provides 13.8 Vdc at 17 amps, while accepting 90 to 130 Vac input.
The MFJ-4110 is the answer for the travelling operator. It plugs right in to a 110 Vac outlet
with the included adapter and delivers 13.8 Vdc at 2 amps. An LED indicator lets you
know it’s working.
Though it’s tailored for Yaesu’s FT-817, the MFJ-4103 switching power supply can work
with many other QRP rigs. In addition to over-current, over-temperature and overvoltage protection, the MFJ-4103 accepts 100-240 Vac at 47-63 Hz—which means you can
plug it in virtually anywhere. Output is 13.8 Vdc at 2.89 amps, through a 2.1mm plug.
DXEngineering.com has detailed specs for every MFJ power supply.
MFJ-4115
MFJ-4110
MFJ-4103
MFJ Basic Switching Power Supply...................................... $59.95
MFJ Power Supply ................................................................. $59.95
MFJ Power Supply for FT-817................................................ $46.95
ASR-LS-35A
LS Power Supplies
Delivering an adjustable 22 to 32 volts of
regulated DC power, these Astron linear power
supplies feature over-voltage protection, lowripple and a heavy duty heat sink. Each power
supply incorporates fold-back current limiting to
protect it from excessive current and accidental shorts.
Part Number
ASR-LS-10A
ASR-LS-18A
ASR-LS-25A
ASR-LS-35A
ASR-LS-35M
Is your antenna array far from your shack? Here’s a
great way to ensure you can still get DC power down your
coax to operate your remote tuners, rotor, etc. It works on
frequencies from 1 to 60 MHz and has a switch to turn your
remote equipment on and off. This unit requires a standard
2.1mm, 1A (max.) power adapter.
MFJ-4117
Bias-Tee Power Injector ...........$29.95
Get Your Gear Faster. If you get your order in by 10 pm ET and the parts are in stock, DX
Engineering will ship it immediately. We carry thousands of items, that means you’ll
get your order as quickly as possible. If you don’t like to wait, count on us to get your
order out quickly.
Power Supply
Power Supply
Power Supply
Power Supply
Supply with Dual Meters
Amps
Continuous/Peak
8A/10A at 28 Vdc
12A/18A at 28 Vdc
18A/25A at 28 Vdc
27A/35A at 28 Vdc
27A/35A at 28 Vdc
Price
$135.95
$209.95
$291.95
$321.95
$392.95
Rack Mounted Switching Power Supplies
The supplies use high-efficiency switching technology designed solely for precision
communications equipment. For more versatility, they can accept 90 to 130 Vac or
180 to 264 Vac, at 50 or 60 Hz. These fan-cooled supplies deliver a consistent 13.8 Vdc.
Part Number
Bias-Tee Power Injector
Description
ASR-LS-35M
ASR-SRM-10
ASR-SRM-12
ASR-SRM-18
ASR-SRM-25
ASR-SRM-25M
ASR-SRM-25-2
ASR-SRM-25M-2
ASR-SRM-30
ASR-SRM-30M
ASR-SRM-30-2
ASR-SRM-30M-2
Description
Power Supply
Power Supply
Power Supply
Power Supply
Power Supply, Dual Meters
Dual SRM-25 Power Supplies
Dual SRM-25M Power Supplies
Power Supply
Power Supply, Dual Meters
Dual SRM-30 Power Supplies
Dual SRM-30M Power Supplies
Orders by 10 pm ET Ship Same Day, See Page 58 for Details
Amps
Continuous/Peak
7A/10A at 13.8 Vdc
9A/12A at 13.8 Vdc
15A/18A at 13.8 Vdc
20A/25A at 13.8 Vdc
20A/25A at 13.8 Vdc
20A/25A at 13.8 Vdc
20A/25A at 13.8 Vdc
25A/30A at 13.8 Vdc
25A/30A at 13.8 Vdc
25A/30A at 13.8 Vdc
25A/30A at 13.8 Vdc
Price
$89.95
$99.95
$109.95
$129.95
$149.95
$249.95
$289.95
$138.95
$189.95
$269.95
$348.95
DC Power & Accessories
35
Rack Mounted Linear Power Supplies
RS Power Supplies
Get consistent, reliable power using these
ASR-RM-50M
rack mounted linear power supplies. These
adjustable, solid state supplies are electronically regulated to offer less than 5mV peak
to peak ripple. They incorporate fold-back current limiting and a heavy duty heat sink
to ensure years of solid power delivery. Find full details at DXEngineering.com.
Rack Mounted Power Supply with 2 to 15 Vdc Adjustable Output
These rugged, reliable units are electronically
regulated to maintain low ripple at low-line input
voltage. They provide an adjustable 11 to 15 Vdc
ASR-RS-35M
and include fold-back current limiting to protect your
power supply from excessive current and continuous shorted output. Depending on the
model, you get features like crowbar over-voltage protection, heavy-duty heat sinks, and
chassis-mounted fuses for extra protection against overheating and shorting.
Part Number
Amps
Continuous/Peak
7A/11A at 13.8 Vdc
Description
ASR-VRM-35M-BB Supply, Dual Meters, Battery Backup
Price
$397.95
Rack Mounted Power Supplies with 11 to 15 Vdc Adjustable Output
Part Number
Description
ASR-RM-12A
ASR-RM-12A-BB
ASR-RM-12M
ASR-RM-12M-BB
ASR-RM-20A
ASR-RM-20A-BB
ASR-RM-20M
ASR-RM-20M-BB
ASR-RM-35A
ASR-RM-35A-BB
ASR-RM-35M
ASR-RM-35M-BB
ASR-RM-50A
ASR-RM-50A-BB
ASR-RM-50M
ASR-RM-50M-BB
ASR-RM-60A
ASR-RM-60A-BB
ASR-RM-60M
ASR-RM-60M-BB
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Amps
Continuous/Peak
9A/12A at 13.8 Vdc
9A/12A at 13.8 Vdc
9A/12A at 13.8 Vdc
9A/12A at 13.8 Vdc
16A/20A at 13.8 Vdc
16A/20A at 13.8 Vdc
16A/20A at 13.8 Vdc
16A/20A at 13.8 Vdc
25A/35A at 13.8 Vdc
25A/35A at 13.8 Vdc
25A/35A at 13.8 Vdc
25A/35A at 13.8 Vdc
37A/50A at 13.8 Vdc
37A/50A at 13.8 Vdc
37A/50A at 13.8 Vdc
37A/50A at 13.8 Vdc
50A/55A at 13.8 Vdc
50A/55A at 13.8 Vdc
50A/55A at 13.8 Vdc
50A/55A at 13.8 Vdc
Price
$126.95
$159.95
$167.95
$185.95
$169.95
$185.95
$179.95
$217.95
$309.95
$339.95
$307.95
$381.95
$352.95
$409.95
$381.95
$421.95
$453.95
$511.95
$463.95
$561.95
Description
ASR-LSRM-18A
ASR-LSRM-18A-BB
ASR-LSRM-18M
ASR-LSRM-18M-BB
ASR-LSRM-25A
ASR-LSRM-25A-BB
ASR-LSRM-25M
ASR-LSRM-25M-BB
ASR-LSRM-35A
ASR-LSRM-35A-BB
ASR-LSRM-35M
ASR-LSRM-35M-BB
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Power Supply
Power Supply, Battery Backup
Power Supply, Dual Meters
Supply, Dual Meters, Battery Backup
Amps
Continuous/Peak
12A/18A at 28 Vdc
12A/18A at 28 Vdc
12A/18A at 28 Vdc
12A/18A at 28 Vdc
18A/25A at 28 Vdc
18A/25A at 28 Vdc
18A/25A at 28 Vdc
18A/25A at 28 Vdc
27A/35A at 28 Vdc
27A/35A at 28 Vdc
27A/35A at 28 Vdc
27A/35A at 28 Vdc
Price
$329.95
$315.95
$315.95
$335.95
$372.95
$342.95
$382.95
$409.95
$404.95
$445.95
$529.95
$476.95
Astron’s SLS Series supplies are filtered specifically against RF interference,
including the HF range. They also include an EMI filter, making them perfect for
powering sensitive communications equipment. These supplies provide 28 Vdc, and
include current limiting, over-voltage and thermal protection, and a fused input. The
SLS Series supplies are also selectable for 115 or 220 Vac input at either 50 or 60 Hz for
excellent versatility.
Part Number
Description
ASR-SLSRM-15
ASR-SLSRM-15-2
ASR-SLS-15
Rack Mounted SLS Power Supply
Dual Rack Mounted SLS Supplies
Standalone SLS Power Supply
Amps
Continuous/Peak
12.5A/15A at 28 Vdc
12.5A/15A at 28 Vdc
12.5A/15A at 28 Vdc
Description
ASR-RS-3A
ASR-RS-4A
ASR-RS-4L
ASR-RS-5A
ASR-RS-7A
ASR-RS-12A
ASR-RS-12M
ASR-RS-12A-BB
Power Supply
Power Supply
Supply, Cigarette Lighter Port
Power Supply
Power Supply
Power Supply
Supply with Switchable Meter
Supply with Battery Backup
Supply with Meter and
Backup
Power Supply
Supply with Dual Meters
Supply with Battery Backup
Supply with Meters and
Backup
Power Supply
Supply with Dual Meters
Power Supply
Supply with Dual Meters
Power Supply
Supply with Dual Meters
ASR-RS-12M-BB
ASR-RS-20A
ASR-RS-20M
ASR-RS-20A-BB
ASR-RS-20M-BB
ASR-RS-35A
ASR-RS-35M
ASR-RS-50A
ASR-RS-50M
ASR-RS-70A
ASR-RS-70M
Amps
Continuous/Peak
2.5A/3A at 13.8 Vdc
3A/4A at 13.8 Vdc
3A/4A at 13.8 Vdc
4A/5A at 13.8 Vdc
5A/7A at 13.8 Vdc
9A/12A at 13.8 Vdc
9A/12A at 13.8 Vdc
9A/12A at 13.8 Vdc
$53.95
$59.95
$57.95
$66.95
$72.95
$92.95
$103.95
$113.95
9A/12A at 13.8 Vdc
$119.95
16A/20A at 13.8 Vdc
16A/20A at 13.8 Vdc
16A/20A at 13.8 Vdc
$114.95
$136.95
$144.95
16A/20A at 13.8 Vdc
$164.95
25A/35A at 13.8 Vdc
25A/35A at 13.8 Vdc
37A/50A at 13.8 Vdc
37A/50A at 13.8 Vdc
57A/70A at 13.8 Vdc
57A/70A at 13.8 Vdc
$175.95
$199.95
$281.95
$315.95
$361.95
$402.95
Astron’s VS line of 13.8 Vdc power supplies have
the same reliable performance of the RS line. These
models also feature front-panel knobs, so you can
easily adjust output from 2 to 15 Vdc. They also include
separate front-panel volt and amp meters.
Part Number
ASR-VS-12M
ASR-VS-20ML
ASR-VS-35M
ASR-VS-50M
ASR-VS-70M
Description
Power Supply
Supply, Cigarette Lighter Port
Power Supply
Power Supply
Power Supply
Amps
Continuous/Peak
9A/12A at 13.8 Vdc
16A/20A at 13.8 Vdc
25A/35A at 13.8 Vdc
37A/50A at 13.8 Vdc
57A/70A at 13.8 Vdc
Price
Price
$139.95
$269.95
$124.95
ASR-VS-35M
Price
$155.95
$156.95
$207.95
$322.95
$402.95
SS Series Switching Power Supplies
If you need a power supply that doesn’t eat up the
space on your desk, Astron offers these low profile
options. They deliver a steady 13.8 Vdc and are built to
be immune to RFI. These supplies include an EMI filter to
resist RFI, even in the HF bands.
ASR-SLSRM-15
SLS Series Switching Power Supplies
Part Number
VS Power Supplies
Rack Mounted Power Supplies with 22 to 32 Vdc Adjustable Output
Part Number
“BB” in the part number denotes models that have an integrated battery backup and trickle charger.
An “M” in the part number indicates that the units have either dual or single volt/amp meters.
ASR-SS-25M
The “M” in the part number denotes models that include front panel volt and amp meters.
Part Number
ASR-SS-10
ASR-SS-12
ASR-SS-18
ASR-SS-25
ASR-SS-25M
ASR-SS-30
ASR-SS-30M
Description
Power Supply
Power Supply
Power Supply
Power Supply
Supply with Dual Meters
Power Supply
Supply with Dual Meters
International Shipping is Quick and Easy! See Page 58 for Details
Amps
Continuous/Peak
7A/10A at 13.8 Vdc
10A/12A at 13.8 Vdc
15A/18A at 13.8 Vdc
20A/25A at 13.8 Vdc
20A/25A at 13.8 Vdc
25A/30A at 13.8 Vdc
25A/30A at 13.8 Vdc
Price
$79.95
$88.95
$93.95
$119.95
$139.95
$129.95
$149.95
36
DC Power & Accessories
DXE Number Samlex Number
Description
Receptacles
Surge Capability
Price
SXA-07093
PSE-12125A
1,250 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
2 AC
2,500 Watts
$282.63
SXA-07103
PSE-12175A
1,750 Watt Modified Sine
DC/AC Inverter, 12 Vdc input
2 AC
3,500 Watts
$339.15
SXA-07113
PSE-12275A
2,750 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
1 AC
4,500 Watts
$662.15
SXA-07174
PSE-24275A
2,750 Watt Modified Sine
DC/AC Inverter, 24 Vdc Input
1 AC
4,500 Watts
$709.16
SXA-07184
PSE-24175A
1,750 Watt Modified Sine
DC/AC Inverter, 24 Vdc Input
2 AC
3,500 Watts
$356.15
DC/AC Modified
Sine Wave Inverters
SXA-07806
SAM-100-12
100 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
1 AC
1 USB
200 Watts
$20.23
If you just need reliable DC power for your tools, lights
or appliances, then you don’t need a full, pure sine
converter. Save yourself some money and check out
these modified DC/AC converters. They convert 12- or
24-volt DC input voltage into reliable 120-Volt AC, The
modified sine design means you still get rock-solid
power with a gentler bite on your wallet.
SXA-07807
SAM-250-12
250 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
1 AC
1 USB
500 Watts
$27.29
SXA-07808
SAM-450-12
450 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
2 AC
1 USB
900 Watts
$38.25
SXA-07828
SAM-450-12E
450 Watt Modified Sine
DC/AC Inverter, 12 Vdc
1 AC
1 USB
900 Watts
$42.21
SXA-07809
SAM-800-12
800 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
2 AC
1 USB
1,600 Watts
$66.22
SXA-07812
SAM-1000-12
1,000 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
2 AC
2,000 Watts
$105.83
SXA-07817
SAM-1500-12
1,500 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
2 AC
3,000 Watts
$196.27
SXA-07827
SAM-2000-12
2,000 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
3 AC
4,000 Watts
$227.61
SXA-07836
SAM-7836
3,000 Watt Modified Sine
DC/AC Inverter, 12 Vdc Input
3 AC
6,000 Watts
$403.75
Description
Input Range
Output Range
Price
SXA-07093
SXA-06204
DC/DC Step-Up
Converters
Perfect for atypical or higher voltage DC applications,
these negative-ground converters can give you clean
DC power along with over-voltage and polarity
protection, plus temperature-controlled current limiting.
You can find the complete specs on each unit at
DXEngineering.com.
DXE Number Samlex Number
SXA-06204
VTC305-12-24
DC/DC Step-Up Converter
10.5-28 Vdc
12-27 Amps
at 24-27.5 Vdc
$929.95
SXA-06214
VTC605-12-24
DC/DC Step-Up Converter
10.5-28 Vdc
20-45 Amps
at 24-27.5 Vdc
$1,047.95
SXA-06760
STEP 7
DC/DC Step-Up Converter
9-18 Vdc
7 Amps at 24 Vdc
$100.89
SXA-06765
STEP 10
DC/DC Step-Up Converter
9-18 Vdc
10 Amps at 24 Vdc
$140.22
Description
Input Range
Output Range
Price
SXA-06701
DXE Number Samlex Number
Isolated
DC/DC Converters
If you need to convert precise
DC voltages, even in positive-ground systems, Samlex
offers several proven options. These converters feature
over-voltage, reverse polarity and short-circuit
protection, plus fold-back current limiting. They’re ideal
in mobile/portable installations where clean DC power
can be scarce.
SXA-06044
Mean Well DC/DC
Fully Isolated Converters
SXA-06701
IDC-100A-12
Step-Up Isolated
DC/DC Converter
9-18 Vdc
8A at 12.5 Vdc
$135.09
SXA-06706
IDC-100A-24
Step-Up Isolated
DC/DC Converter
9-18 Vdc
4A at 24.5 Vdc
$135.09
SXA-06708
IDC-100C-24
Isolated DC/DC Converter
30-60 Vdc
4A at 24.5 Vdc
$135.09
SXA-06720
IDC-200A-12
Isolated DC/DC Converter
9-18 Vdc
16A at 12.5 Vdc
$164.95
SXA-06721
IDC-200B-12
Isolated DC/DC Converter
20-35 Vdc
16A at 12.5 Vdc
$160.74
SXA-06722
IDC-200C-12
Isolated DC/DC Converter
30-60 Vdc
16A at 12.5 Vdc
$158.95
SXA-06723
IDC-200D-12
Isolated DC/DC Converter
60-120 Vdc
16A at 12.5 Vdc
$160.74
SXA-06726
IDC-200A-24
Isolated DC/DC Converter
9-18 Vdc
8A at 24.5 Vdc
$160.74
SXA-06728
IDC-200C-24
Isolated DC/DC Converter
30-60 Vdc
8A at 24.5 Vdc
$160.74
SXA-06730
IDC-360A-12
Isolated DC/DC Converter
9-18 Vdc
30A at 12.5 Vdc
$300.96
DXE Number Samlex Number
If you have a positive-ground system
and need a reliable step-down converter to
produce noise-free power, Samlex comes to your
rescue. These converters are fully isolated, which
means they’re compatible with both negative- and
positive-ground systems. They all also feature automatic
short-circuit, overload and over-voltage protection.
Description
Input Range
Output Range
Price
SXA-06044
SD-150D-12
Fully Isolated DC/DC Converter
72-144 Vdc
12.5A at 12 Vdc
$103.14
SXA-06054
SD-150C-12
Fully Isolated DC/DC Converter
36-72 Vdc
12.5A at 12 Vdc
$103.14
SXA-06064
SD-150C-24
Fully Isolated DC/DC Converter
36-72 Vdc
6.25A at 24 Vdc
$103.14
SXA-06104
SD-150B-24
Fully Isolated DC/DC Converter
19-36 Vdc
6.25A at 24 Vdc
$103.14
More Products, Specs and Photos at DXEngineering.com
DC Power & Accessories
37
SXA-03431
SXA-14242
SXA-14008
SXA-03435
Desktop Switching Power Supplies
Need a rock-solid 13.8 Vdc power supply that doesn’t take up half of your shack?
Samlex offers compact and reliable Desktop Switching Power Supplies. They’re loaded
with over-current, over-voltage and short-circuit protection and are well filtered to
produce clean, noise-free power.
SXA-14002
Mean Well Single Output Switching Power Supplies
For a versatile supply that delivers reliable power levels, check out these offerings
from Samlex. You can adjust both input and output voltage, making these power
supplies handy tools in your shack or on your bench. They are well-filtered units
that give you clean, reliable power without unwanted noise and RFI. They also offer
over-voltage, over-current and short-circuit protection to keep your gear safe.
DXEngineering.com has more detailed specs on each of these supplies.
Description
Power
Input
Range
Power
Output
Range
Price
S-25-12
25 Watt Power Supply
2.1A at 12 Vdc
85-260 Vac
10.8-13.2
Vdc
$31.14
SXA-14003
S-60-12
60 Watt Power Supply
5A at 12 Vdc
85-260 Vac
10.8-13.2
Vdc
$41.04
SXA-14012
S-100F-12
100 Watt Power Supply
85-370 Vac
8.5A at 12 Vdc
10.8-13.2
Vdc
$49.77
SXA-14004
S-150-12
150 Watt Power Supply
85-260 Vac
12.5A at 12 Vdc
10.6-13.2
Vdc
$58.68
SXA-14022
S-320-12
320 Watts Power
Supply 25A at 12 Vdc
85-260 Vac
10-13.2
Vdc
$118.89
SXA-14005
S-25-24
25 Watt Power Supply
1.1A at 24 Vdc
85-260 Vac
21.6-26.4
Vdc
$31.14
SXA-14009
S-60-24
60 Watt Power Supply
2.5A at 24 Vdc
85-260 Vac
21.6-26.4
Vdc
$41.04
SXA-14006
S-150-24
150 Watt Power Supply
85-250 Vac
6.5A at 24 Vdc
21-28.4
Vdc
$58.68
SXA-14008
S-320-24
320 Watt Power Supply
85-260 Vac
12.5A at 24 Vdc
21-28.4
Vdc
$118.89
SXA-14125
SE-600-48
600 Watt Power Supply
85-260 Vac
12.5A at 48 Vdc
43-56
Vdc
$185.40
SXA-14242
SE-100-48
1,000 Watt Power
Supply 20.8A at 48 Vdc
43-56
Vdc
$342.00
DXE
Number
SXA-14002
Samlex
Number
85-370 Vac
DXE
Number
Samlex
Number
Desktop Power Supply
Description
SEC-1212
120 Vac
10A at 13.8 Vdc
$101.75
SXA-03052
SEC-1212CE
230 Vac
10A at 13.8 Vdc
$107.44
SXA-03061
SEC-1223
120 Vac
23A at 13.8 Vdc
$125.97
SXA-03062
SEC-3062
230 Vac
23A at 13.8 Vdc
$132.43
SXA-03431
SEC-1235
120 Vac
30A at 13.8 Vdc
$133.28
SXA-03435
SEC-1235M
Dual Meters, 120 Vac
30A at 13.8 Vdc
$143.74
SXA-03064
SEC-03064
Battery Backup, 120 Vac
23A at 13.8 Vdc
$118.95
Rack Plates
These durable standard-width rack
plates are a great way to get your
SEC-series power supplies off your
desk and into a rack. They have a black
powdercoat finish and cutouts for bottom-mounted fans.
SXA-03104
Rack Plate for Single Supply, 3.5" High ............................... $41.95
SXA-03105
Rack Plate for Dual Supplies, 3.5" High............................... $49.95
Rackmount
Switching
Power Supplies
Do you have a rack in your
shack? Here’s a great way to get
your power supply off of your
desk without compromising
SXA-03111
your power needs. They all
produce clean, reliable power and are available in a wide range of DC output levels. These
power supplies come mounted on a two rack unit size plate and feature over-current,
over-voltage and short-circuit protection to keep your gear safe.
DXE
Number
Samlex
Number
Going from 24 Vdc down to 13.8 Vdc is no problem
with these reliable step-down converters. If you
have an input voltage of 20-35 Vdc, these
converters let your expensive gear sip a steady diet
of clean, stable 13.8 Vdc. Designed for negative
ground, heavy-duty applications, the converters
all offer over-voltage, reverse polarity and shortcircuit protection, plus temperature-regulated
current limiting.
DXE
Number
Samlex
Number
Description
Output
SXA-06014
SDC-15
DC/DC Converter
15A at 13.8 Vdc
$74.95
SXA-06024
SDC-23
DC/DC Converter
20A at 13.8 Vdc
$83.95
SXA-06034
SDC-5
DC/DC Converter
5A at 13.8 Vdc
$40.95
SXA-06036
SDC-12
DC/DC Converter
12A at 13.8 Vdc
$54.95
DC/DC Converter
30A at 13.8 Vdc
Power
Output
Price
SEC-1223R1
Rackmount Power Supply
120 Vac
20A at
13.8 Vdc
$159.95
SXA-03261
SEC-40BRM
Rackmount Power Supply
with Battery Backup
and Charger 120 Vac
40A at
13.8 Vdc
$388.95
SXA-03271
SEC-60BRM
Rackmount Power Supply
with Battery Backup
and Charger 120 Vac
60A at
13.8 Vdc
$448.95
SXA-03281
SEC-80BRM
Rackmount Power Supply
with Battery Backup
and Charger 120 Vac
80A at
13.8 Vdc
$454.95
SXA-03291
SEC-100BRM
Rackmount Power Supply
with Backup, Charger
and Meter 120 Vac
100A at
13.8 Vdc
$549.95
SXA-03312
SEC-40BRM-220
Rackmount Power Supply
with Battery Backup
and Charger 230 Vac
40A at
13.8 Vdc
$428.95
SXA-03342
SEC-100BRM-220
Rackmount Power Supply
with Battery Backup
and Charger
100A at
13.8 Vdc
$598.95
SXA-03364
SEC-2450BRM
Rackmount Power Supply
with Backup, Charger
and Meter
50A at
27.6 Vdc
$528.95
Price
$136.95
Description
SXA-03111
Switching DC/DC Converters
SDC-30
Price
SXA-03051
SXA-06014
SXA-06174
Power
Output
FREE Standard SHIPPING for Orders Over $99, See Page 58 for Details
38
DC P
DC
Power
ower & A
Accessories
ccessories
SXA-07374
Super Battery Booster
Your mobile rig may not always get a stable
13.8 Vdc from your vehicle’s battery. To
combat the fluctuations in power and keep
your radio operating at its fullest potential,
install this MFJ Battery Booster. It ensures a
steady stream of 13.8 Vdc and can be tailored to specific voltage limits, protecting your
battery from over-discharge. An internal 30 amp input fuse prevents excess output and
this unit has over-voltage protection. Input voltage and output voltage are adjustable.
MFJ-4416B
Super Battery Booster ........................................................ $149.95
SXA-07323
DC/AC Pure Sine Wave Inverters
Radios, computers, A/V equipment and virtually any piece of precision
electronic gear need the cleanest, most stable power source to function properly. Pure sine wave inverters are the best way to keep your
transceiver and shack equipment functioning at their peak.
DXE
Number Samlex Number
SXA-07173 PST-15S-12A
SXA-07215 PST-600-12
SXA-07313 PST-30S-12E
SXA-07323 PST-60S-12E
SXA-07374 SSW-1500-12A
SXA-07461 SA-300-112
Power
In/Out
12 Vdc/110 Vac
12 Vdc/110 Vac
12 Vdc/230 Vac
12 Vdc/230 Vac
12 Vdc/115 Vac
12 Vsc/110 Vac
Watts
Cont./Surge
150/300
600/1,200
300/500
600/1,000
1,500/3,000
300/400
Receptacles
1 AC
2 AC
1 Schuko
1 Schuko
2 AC
2 AC
Price
$121.81
$225.59
$191.52
$273.60
$374.34
$153.95
Battery Backup Module
Add battery backup to your shack. Just connect
this unit between your power supply and a wet or SLA
standby battery, and it acts as a float charger to keep the battery
ready. If your AC power fails, it will automatically switch to the
battery in an instant. Fuses protect the circuit during battery
charge/discharge, and a front LED indicates the charging status.
Maximum battery load is 30A and the unit limits charging at 3.6A. The
module works with 12- and 24-volt systems.
ASR-BB-30M
Battery Backup Module ........................................................ $53.95
Battery Backup Module
Connect this module to your power supply
and battery to make a battery backup
system. When your AC power fails, the unit
will instantly switch to your battery. When the AC
power is restored, it switches back to charging.
The module works with voltages from below 12 Vdc, up to
28 Vdc and can handle a maximum output current of 100 amps. This float-type battery
charger can be an essential backbone for your shack or EMCOMM setup.
SXA-08081
Battery Backup Module ...................................................... $128.95
N2412-12 and N2412-24
DC/DC Converters
ASR-N2412-12
Astron has packed these converters with
ASR-N2412-24
some impressive features, including over-voltage, over-current
and short circuit protection. You can also set up these converters to turn on
with your ignition switch for hassle-free operation. They accept 22-33 Vdc input with a
13.8 Vdc output. The N2412-12 delivers 10 amps of continuous current with a 12 amp
peak, while the N2412-24 delivers 20 amps continuous with a 24 amp peak.
ASR-N2412-12
DC/DC Converter, 12 Amp Peak............................................ $59.95
ASR-N2412-24
DC/DC Converter, 24 Amp Peak............................................ $89.95
Step-Down DC/DC Converters
Battery Isolating Load Protector
This unit protects your battery and its load by isolating
them from a variety of power faults. In the event of
excessive load, this device will disconnect the battery
automatically. You can program your own fault thresholds
and it can handle 40 amps.
SXA-08645
DC Isolating Load Protector ................................................. $73.95
Universal Computerized
Battery Analyzer
A complete battery-test lab in a box.
The “CBA” carries advanced features
you won’t see in a standard battery
tester. It can test virtually any battery
up to 55V, regardless of type, size, or
cell number. The analyzer handles a
maximum of 40 amps and 150 watts.
Test data is displayed in easy-to-read
chart and graph readouts, and there
is a slick printout feature that lets you
create labels to attach to the battery.
That means you’ll be able to keep tabs on the status of your battery.
You can also add an optional DC amplifier that amplifies and regulates discharge current
so you can test your battery at a high discharge rate. The 58206-1009 is intended for
industrial grade use and improper use is hazardous, so make sure this amplifier isn’t
overkill for your application.
An optional temperature probe lets you limit how hot your batteries get during testing.
WMT-58250-1015 Universal Computerized Battery Analyzer ........................ $189.95
WMT-58206-1009 CBA Battery Discharge Amplifier.......................................... $33.95
WMT-58256-1020 Temperature Probe for CBA.................................................. $12.95
Offering a high-efficiency DC conversion, these
units are great if you’ve got a specialized DC
power source and need it stepped-down to a
stable 13.8 Vdc. They have over-voltage, short circuit
and reverse polarity protection (on the input side).
The 2412-40 and A4812-12 are designed for negative ground
applications, while the ISO4812-24 is fully isolated, ideal for positive ground systems.
Part Number
Description
ASR-2412-40
ASR-A4812-12
ASR-ISO4812-24
DC/DC Converter
DC/DC Converter
Isolated DC Converter
Input Voltage
Max.
Output
Current
Price
22 to 32 Vdc
30-56 Vdc
36 to 72 Vdc
32A
9A
20A
$205.95
$49.95
$149.95
Find More Brands, More Products and
More Specs at DXEngineering.com
• We’re constantly adding more products to make your on-air
experience better. Check back often and see what’s new.
• Want more info on anything we sell? You’ll find
detailed specs and a comprehensive F.A.Q. section.
• Whenever possible, we post FREE downloadable
instruction manuals a nd stat sheets so you
can better research a product.
• There’s a wealth of interesting and FREE tech
articles available. Maybe you can learn
something new?
Hit the Air
Whether it’s a long-haul contest or a casual ragchew, the fun of our hobby is
being on the air. We only carry products that improve your on-air experience,
gear that allows you to hear and be heard. And we’re always adding more.
Visit DXEngineering.com and see what’s new.
1-330-572-3200: Expert Tech Advice 8:30 am to 4:30 pm ET Monday-Friday
DC Power & Accessories
SXA-08302
Battery Tender Systems
SXA-08306
Three Stage Battery Chargers
Capable of charging flooded, AGM or Gel-Cell batteries, these UL-/ETL-approved
chargers are versatile enough for multiple applications. Depending on the model, they
can charge several banks of batters simultaneously, and when sized right, they’ll be
able to charge a battery even while it is under load. The chargers feature an ammeter,
and incorporate short circuit, overload, and reverse polarity protection.
DXE
Number
SXA-08301
SXA-08302
SXA-08305
SXA-08306
Samlex
Number
SEC-1215UL
SEC-1230UL
SEC-2415UL
SEC-2425UL
Description
Charger
Charger, Handles 3 Battery Banks
Charger
Charger, Dual Ammeters
Voltage/
Amperage
12 Vdc/15A
12 Vdc/30A
24 Vdc/15A
24 Vdc/25A
Price
$144.25
$218.03
$218.03
$352.07
Solar Charging Kits
Harness the sun to power your gear. These
comprehensive kits include everything but
a battery. They are expandable to 500 watts,
so they’re the perfect starting point for your
solar powered system. The kits feature a
30 amp charge controller, a high-efficiency
solar panel, solar connecting wires and
mounting hardware. You can use these
kits in your mobile, EMCOMM, or battery
backup systems. See DXEngineering.com for
complete system specs.
DXE
Number
Samlex
Number
SXA-18018
SRV-50-KIT-USA
SXA-18019
SRV-EXP-50-KIT-USA
SXA-18014
SRV-90-KIT-USA
SXA-18016
SRV-EXP-90-KIT-USA
SXA-18015
SRV-135-KIT-USA
SXA-18017
SRV-EXP-135-KIT-USA
SXA-08725
SOLSUM 6.6 F
SXA-08727
SOLSUM 10.10 F
39
Description
50 W Charging System,
3.2A Max. Output Current
Solar Panel Expansion Kit for
50 W System
90 W Charging System,
5.31A Max. Output Current
Solar Panel Expansion Kit for
90 W System
135 W Charging System,
8.1A Max. Output Current
Solar Panel Expansion Kit for
135 W System
Solar Charger Controller,
6 Amp Max. Current
Solar Changer Controller,
10 Amp Max. Current
Price
$424.95
If you’re running a high-power mobile rig, dual
batteries or a battery-powered standalone
EMCOMM trailer, it’s a good idea to take care of
your battery. Deltran offers you several fantastic
options in the Battery Tender line. Much better
than simple trickle chargers, these units are
packed with features to ensure that you’ll have
plenty of reliable DC on hand when you need it.
Battery Tender Plus
Designed to charge and maintain batteries at the proper
storage level, the Battery Tender Plus is the flagship of
Deltran’s Battery Tender line. Using a three-step charging
mode (bulk charge, absorption and float), the Battery
Tender Plus keeps your battery charged without
the damaging effects of a basic trickle charger. It
features a quick-connect harness, reverse polarity
protection and auto-switching between charging
modes. It even reacts to ambient temperatures, adjusting
charging power to ensure that your battery is ready to go, when you need it.
DTN-021-0128
Battery Tender Plus .........................................................$51.87
Battery Power Tender Plus
The Battery Power Tender Plus can charge and maintain both
sealed maintenance-free batteries and traditional
lead-acid batteries. Its four-step charging program
is microprocessor-controlled to avoid damaging
your battery while charging, and it features reverse
polarity protection for trouble-free use.
DTN-0220142DLWHB Battery Power Tender Plus........................................... $101.20
Battery Tender Waterproof 800
Great for the field, the Battery Tender Waterproof 800 Charging
System packs 800 mA of charging power into a compact package. It
will constantly monitor your battery, making sure that it maintains
optimum performance levels. The Waterproof 800 features short
circuit and reverse polarity protection and resists the elements for
years of trouble-free use.
DTN-022-0150DLWH Battery Tender Waterproof 800 .....$39.33
Battery Tender Junior
If you’re small on space but big on power demands, ensure you have
a steady supply of DC with Deltran’s Battery Tender Plus Junior. It
has many of the powerful features of its big brothers in a small,
extremely portable and lightweight package. It’s spark-proof,
with reverse polarity protection and a two-color LED
indicates your battery’s charging state.
DTN-021-0123
Battery Tender
Junior .......................................$25.30
$384.95
Powermaster
Battery Isolator
$557.95
We’ve all been there: a busy Field Day or
DXpedition. You make plenty of contacts
while your gear sips a steady diet of voltage from your car’s
auxiliary battery. When it’s time to leave—your car won’t start!
Using an auxiliary battery doesn’t always protect your primary battery from draining.
Powermaster’s Battery Isolator prevents this unwanted drain. It ties your batteries
together, allowing them both to charge from your engine’s alternator. Since your
auxiliary battery is isolated, it won’t drain the charge from your primary battery in the
event of excess load.
Use Powermaster’s Battery Isolator when you’re operating off your vehicle’s battery
power and keep yourself from being stranded.
PWM-903
Powermaster Battery Isolator ............................................ $109.97
$465.95
$594.95
$557.95
$39.95
$62.95
Solar Trickle Chargers
These chargers are designed for maintaining lighter-duty,
12-volt batteries. Well suited to vehicle applications, these
trickle chargers will keep your battery ready to go, even if it’s
been sitting idle for months. The chargers plug right into a
cigarette lighter socket—just make sure the socket remains
on with the vehicle’s key out.
They can be used in permanent or temporary installations, and are perfect
solutions if you park your vehicle in a remote garage without AC power.
SXA-17031
Solar Trickle Charger, 4.8 Peak Watts, 0.30A Output .......... $85.95
SXA-17032
Solar Trickle Charger, 9.5 Peak watts, 0.56A Output ........$122.95
Digital 1200 Battery Charger
A battery charger for the 21st century! This
charger can recover deeply discharged batteries and
extend battery life. It features an LCD display and intuitive GUI
that indicates charging status, plus an integrated work light. The Digital 1200 even
includes a USB part to charge your smart phone and other USB-powered devices. It
accepts 100 to 120 Vac, has up to 14.9 Vdc output and can be used for flooded and AGM
batteries—find all the specs at DXEngineering.com.
ULT-150-34178
Digital 1200 Battery Charger .............................................. $199.99
International Shipping is Quick and Easy! See Page 58 for Details
40
DC Power & Accessories
RS-50A
Linear Power Supply
WMT-58303-1030
WMT-58315-1043
WMT-58307-1037
RIGrunner
DC Outlet Panels
Got a pile of spaghetti where
your DC power cables should
be? These RIGrunner Outlet Panels will clean up your shack,
while giving you some advanced features in the process.
WMT-58307-1034
Each outlet is fused for protection and ensures you have
reliable power distribution for your gear. They provide 40 amps of maximum output current and include
Powerpole® connectors and fuses. “U” models have USB ports, handy for charging your smartphone.
Voltage
Alarm
Part Number
Description
WMT-58301-1028
WMT-58303-1030
WMT-58303-1031
WMT-58305-1032
WMT-58305-1033
WMT-58307-1034
WMT-58307-1036
WMT-58307-1037
WMT-58307-1124
WMT-58307-1126
WMT-58307-1125
WMT-58312-1038
WMT-58312-1039
WMT-58312-1040
WMT-58312-1041
WMT-58315-1042
WMT-58315-1043
RIGrunner 8012, 80A Input
RIGrunner 4010S, Auto Turn-On
RIGrunner 4010S, Auto Turn-On
RIGrunner 4012
RIGrunner 4012
RIGrunner 4008
RIGrunner 4008H, Side Connectors
RIGrunner 4008H, Side Connectors
RIGrunner 4008, -48 Vdc Negative
RIGrunner 4008, -48 Positive
RIGrunner 4008, -24 Positive
RIGrunner 4005
RIGrunner 4005
RIGrunner 4005, Side Connectors
RIGrunner 4005, Side Connectors
RIGrunner 4004U, 2 USB Charge Ports
RIGrunner 4004U, 2 USB Charge Ports
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
No
No
No
No
No
Power Cables
8 AWG, 6'
10 AWG, 6'
Sold Separately
10 AWG, 6'
Sold Separately
10 AWG, 6'
10 AWG, 6'
Sold Separately
Sold Separately
Sold Separately
Sold Separately
10 AWG, 6'
Sold Separately
10 AWG, 6'
Sold Separately
10 AWG, 6'
Sold Separately
Powerpole®
Connections
Price
12
10
10
12
12
8
8
8
8
8
8
5
5
5
5
4
4
$159.95
$149.95
$129.95
$129.95
$109.95
$119.95
$109.95
$89.95
$164.95
$124.95
$124.95
$74.95
$64.95
$84.95
$69.95
$94.95
$79.95
When you’ve still got 105-125
Vac available, make sure your DC
power demands are met with this durable and stable
power supply from Astron. It puts out a reliable 13.8
Vdc with 50 amps peak and 37 amps continuous. To
help protect your gear against wild electrical swings,
this electronically-regulated power supply features
over-voltage and current limiting protection.
ASR-RS-50A
Linear Power Supply ..............$281.95
YellowTop
Deep Cycle
12-Volt Battery
Your DC power source needs
to be reliable, rugged and ready-to-go
at a moment’s notice. OPTIMA’s YellowTop battery is
resistant to the elements, recharges quickly and can
recover from deep discharges. This battery is an
excellent fit for your sensitive communications
equipment and can be safely used indoors. In addition
to being spill-proof, YellowTop batteries last longer and
are more durable than most other AGM batteries.
ULT-9050-160
YellowTop
Deep Cycle 12V Battery ..........$285.97
Super PWRgate PG40S
The Super PWRgate maintains
a steady stream of up to
40A continuous from your
power supply or battery
and will instantly switch to battery backup if you lose
power—you won’t even notice the switchover. It also has
a built-in battery charger to ensure that your battery is
ready when you need it.
WMT-58403-1046 Super PWRgate PG40S ...........$139.95
PWRguard Plus PG40S
If your power supply is rapidly
changing, the PWRguard Plus can
sense it and shut the system down,
preventing expensive damage to your equipment. You
can set the voltage trip threshold and the PWRguard has
in-rush current protection as an extra precaution against
damage. It’s rated for a maximum of 40 amps (peak) and
indicator LEDs let you know it is working.
WMT-58402-1045 PWRguard Plus PG40S ...........$114.95
WMT-58312-1355
Powerpole®
Accessories
WMT-58312-1354
Internet Monitored DC Outlet Panels
Take a RIGrunner 4005. Now, add the ability to check its status over
the Internet. The result: the ideal power supply for EMCOMM, remote
power stations or repeaters. They’re also perfectly at home in your shack.
They use an RJ-45 or Wi-Fi for hookup and there is a front-panel LCD to show
the status, voltage and current draw of each outlet.
But the real magic is through the Internet. Using their integrated web server, you can monitor critical parameters or
turn on/off each outlet independently. These are also capable of sending out e-mail alerts for certain alarms.
Part Number
Description
WMT-58312-1353
WMT-58312-1354
WMT-58312-1355
RIGrunner 4005i
RIGrunner 4005i, Wi-Fi Enabled
RIGrunner 4005i, Rack-Mount
Powerpole® Connections
Price
5
5
5
$259.95
$309.95
$429.95
Anderson Powerpole connectors are
quickly becoming the industry standard
for DC power. They have been adopted
by RACES and ARES® for emergency
service and installations. DX Engineering
carries the connectors, plus a tool that makes crimping
them easy and hassle-free.
DXE-PP30
Powerpole Connectors,
12-16 AWG, 30A, 10 Pairs*...$12.95
DXE-PP45
Powerpole Connectors,
10-14 AWG, 45A, 10 Pairs*...$17.95
DXE-UT-CRIMP-PWR Ratcheting Crimp Tool ........$38.95
*One pair equals (1) red and (1) black.
Powerpole® Retention Clips
Avoid accidentally pulling out your
Powerpole connectors by using these clips
to lock them securely to your outlet panel.
WMT-58257-1092
Powerpole Retention Clips,
Set of 12 .................................. $7.95
International Shipping is Quick and Easy! See Page 58 for Details
Your Single Source for Emergency Communication!
IC-7200
HF/50 MHz Transceiver
IC-2820H
Dual-Band FM Transceiver
Rely on this 2M/70cm mobile transceiver to give you
both analog and digital functionality. This transceiver
also uses Icom’s dualwatch feature, so you can monitor
two frequencies at the same time. It packs 50 watts
of power on both bands, which really lets your signal
travel. You can add D-STAR DV mode and GPS receiver
capabilities.
ICO-IC-2820H
Dual-Band FM Transceiver...CALL/WEB
You need a reliable keyer. MFJ’s MFJ-495 lets you key in
CW with a paddle or keyboard and store messages in
its non-volatile memory. The MFJ-495 also has a built-in
speaker with front-panel volume control. It features a
user-friendly interface that is straightforward and intuitive.
It’s easy to set up, so you can get on the air quickly during
an emergency.
MFJ-495
Millennium CW
Memory Keyer .........................$169.95
SX-600
Dual Power Meter
With two meters in one, the SX-600 lets you monitor either
your VHF/UHF or your Low-Band/HF rig. This meter has
low insertion loss yet still gives you accurate readings.
Well suited for QRP, handheld and even high-power
applications, the SX-600 meter is small enough to fit into
a backpack. In an emergency situation, you’ll want to
ensure that your station is working properly. Keep an eye
on things with the SX-600.
DMN-SX600
Dual Power Meter ...................$179.95
RT-21
Universal Digital
Rotor Controller
The latest version of Green Heron’s ubiquitous rotor
controller, the RT-21 is a reliable asset to any installation.
It’s precise and accurate and gives you variable-speed
control. This controller is compatible with a variety of
rotators and is well suited to the Hy-Gain HAM and T2X
units. The RT-21 can support side-mounted antennas and
is fully programmable with easy setup utility software.
GHE-RT-21
Universal Digital
Rotor Controller ......................$559.00
To distribute power through your shack, look to West
Mountain’s RIGrunners. These durable units are the
safest way to power all of your 12 Vdc equipment.
Featuring ultra-reliable Powerpole® connectors,
RIGrunners use automotive-style fuses to prevent
damage and are rated up to 40 amps.
WMT-58307-1035 RIGrunner 4008 .........................$84.95
PWRcheck
Put this in-stream between
your source and load and
you’ll be able to closely
monitor voltage, current, wattage and amp-hours in
real time, in both directions. A large LCD screen displays
everything and there’s an intuitive USB interface.
The PWRcheck also has logging capabilities and the
readouts provide millivolt/milliamp precision.
WMT-58430-1286 PWRcheck ................................$179.95
ISOpwr
Turn your vehicle into a
battery charger! The
ISOpwr lets you connect
an additional battery to
your vehicle’s battery to
charge both of them when the alternator is running.
When the alternator stops, this unit isolates your main
battery to prevent it from draining. It’s an essential tool
for power-hungry mobile installations like an ARES® or
RACES command station.
WMT-58401-1044 ISOpwr .......................................$89.95
CBA IV
Short for “Computerized Battery
Analyzer” the CBA IV is way more advanced than a simple
battery tester. It can handle virtually any battery up to
55V, regardless of type, size, or cell number. It is the best
way to ensure that a battery is ready for an emergency.
WMT-58250-1014 CBA IV .......................................$149.95
DC-to-GO
Battery Box Kit
• Ideal for a trunk-mounted second battery
• Kit includes cables and hardware
SUM-G1200A
Battery Box Kit ..................... $99.97
SUM-G1210
Battery Box Only .................. $14.97
41
Stay Ready—Don’t wait until the power
is out to make a power backup plan, get prepared with
DX Engineering. We’ve put together a comprehensive
list of what you’ll need to get on the air during an
emergency. Find more detailed information on each of
these products at DXEngineering.com.
With the perfect blend of durability, ease of use and
features, this portable transceiver is an excellent choice
for use in the field. It offers up to 100 watts of RF output
(SSB/CW) while giving you VOX and full break-in CW
operation. A backlit LCD screen means you can use it in
dim light and its digital noise reduction makes it easier
to hear weak signals.
ICO-IC-7200
HF/50 MHz Receiver .............CALL/WEB
RIGrunner 4008
MFJ-495
Millennium CW Memory Keyer
EMCOMM
Combine a durable and weather
resistant battery box with one of
West Mountain’s RIGrunner power
distribution centers and you have
a portable power station capable of feeding an entire
radio setup. Available in multiple sizes and RIGrunner
types, these DC-to-GO boxes can be the backbone of your
emergency power system.
WMT-58513-1061 DC-to-GO..................................$134.95
DX Engineering has the tools and equipment to help you
assemble a potent emergency communications unit,
just like this one from the Ashtabula County, Ohio
Amateur Radio Club, K8CY.
Power-Up
with A-iPower
Prepare yourself for
power outages with
the steady power delivery of an A-iPower Portable
generator. These 120-/240-volt AC generators feature
an air-cooled 4-stroke engine, for quiet and reliable
operation. There are several models available, so
whether you need to power an EMCOMM station or a
refrigerator, it’s easy to find the perfect generator for
the job. See detailed specs at DXEngineering.com.
3,750 Watt Generators
• 4.4 HP engine
• 4 gallon fuel tank
with level gauge
• Low oil alert
• Recoil start
• SU4000-CARB E.O. number: U-U-164-0024
AIP-SU4000
3,750 Watt Generator,
49-State Legal..........................$386.97
AIP-SU4000-CARB 3,750 Watt Generator,
50-State Legal..........................$415.97
5,750 Watt Generator
• 7 HP engine
• 7 gallon fuel tank
with level gauge
• Low oil alert
• Digital run time gauge
• Recoil and electric start
AIP-SU5750E
5,750 Watt Generator,
49-State Legal ..................$659.97
7,000 Watt Generator
• 8.1 HP engine
• 7 gallon fuel tank with
level gauge
• Low oil alert
• Digital run time gauge
• Recoil and electric start
AIP-SU7500E
7,000 Watt Generator,
49-State Legal ..................$712.97
8,250 Watt Generators
• 9.7 HP engine
• 7 gallon fuel tank with
level gauge
• Low oil alert
• Digital run time gauge
• Recoil and electric start
• SU-8250E-CARB E.O. number: U-U-164-0026
AIP-SU8250E
8,250 Watt Generator,
49-State Legal ...................$805.97
AIP-SU8250E-CARB 8,250 Watt Generator,
50-State Legal ...................$832.97
1-330-572-3200: Expert Tech Advice 8:30 am to 4:30 pm ET Monday-Friday
Clamps
42
DX Engineering U-Bolt Saddle Clamps
Our U-Bolt Saddle Clamps are ideal for use with round tubing.
Unlike common hardware store clamps that are sized to fit pipe, our clamps are designed and sized to fit tubing.
The U-Bolt Saddle Clamps come with high strength, 18-8 grade stainless steel U-bolts that are long enough to attach
tubing or components to thick mounting plates. The U-bolts are available in 1/4 inch, 5/16 inch and 3/8 inch as listed.
Note that the 2 inch, 2.5 inch and 3 inch clamps are available with either 5/16 inch or 3/8 inch U-bolts.
The U-Bolt Saddle Clamp saddles are cast from high strength 535 aluminum, which has superior anti-corrosion
properties. Unlike stamped or machined types, the saddles’ rippled surface grips tubing closely for a secure fit.
The U-Bolt Saddle Clamps are designed for use with mounting plates, which are available separately.
The clamps are sold only as a set with aluminum saddle, stainless steel U-bolts, nuts, flat washers and
lock washers.
The use of a lubricant and sealant, such as Never-Seez®, is highly recommended to achieve proper torque and prevent
galling. DX Engineering sells replacement U-bolts with hardware kits.
Size
DXE Part
Number
D
L
C
I
T
Hole Size
W
H
t
0.50
DXE-SAD-050A
0.50
1.35
0.75
0.87
1/4"-20
0.266 “H”
0.90
0.188
0.63
$5.25
0.75
DXE-SAD-075A
0.75
1.81
1.00
0.87
1/4"-20
0.266 “H”
1.13
1.00
DXE-SAD-100A
1.00
2.06
1.25
0.87
1/4"-20
0.266 “H”
1.50
0.188
0.75
$5.65
0.250
1.00
$6.05
1.25
DXE-SAD-125A
1.25
2.37
1.50
0.87
1/4"-20
0.266 “H”
1.75
0.250
1.00
$6.85
1.50
DXE-SAD-150A
1.50
2.62
1.75
0.87
1/4"-20
0.266 “H”
1.75
DXE-SAD-175A
1.75
3.00
2.00
1.00
1/4"-20
0.266 “H”
2.00
0.250
1.00
$7.75
2.31
0.250
1.00
$8.90
2.00
DXE-SAD-200A
2.00
3.43
2.31
1.12
5/16"-18
0.332 “Q”
2.62
2.00
DXE-SAD-200B
2.00
4.00
2.37
1.50
3/8"-16
0.397 “X”
2.62
0.375
1.00
$10.05
0.375
1.00
$11.25
2.50
DXE-SAD-250A
2.50
4.18
2.81
1.25
5/16"-18
0.332 “Q”
3.13
0.375
1.13
$12.05
2.50
DXE-SAD-250B
2.50
4.75
2.87
1.75
3/8"-16
0.397 “X”
3.13
0.375
1.13
$13.55
3.00
DXE-SAD-300A
3.00
4.68
3.31
1.25
5/16"-18
0.332 “Q”
3.62
3.00
DXE-SAD-300B
3.00
5.25
3.37
1.75
3/8"-16
0.397 “X”
3.62
0.375
1.25
$13.60
0.375
1.25
$15.25
4.00
DXE-SAD-400A
4.05
5.56
4.43
1.50
3/8"-18
0.397 “X”
4.80
0.438
1.50
$34.70
4.50
DXE-SAD-450A
4.55
6.06
4.93
1.50
3/8"-16
0.397 “X”
5.30
0.438
1.50
$39.95
Correct
Incorrect
Price
Each
Saddle clamps must be used on a flat surface or customer
supplied backing plate. Personal injury and property damage
can occur without proper installation. Always use a lubricant
such as Never-Seez® or Anti-Seize to prevent the stainless steel
hardware from seizing.
DX Engineering Clamps Have Hundreds of Uses!
DX
U-Bolt,
V-Bolt,
andHundreds
Band Clamps
are
DXEngineering
Engineering
Clamps
Have
of Uses!
very
versatile. ForU-Bolt,
example,
we’ve
seen
theClamps
ECLS are
DX Engineering
V-Bolt,
and
Band
Studded
Band Clamps
used towe’ve
fastenseen
merchandise
very versatile.
For example,
the ECLS
display
signs
to upright
Studded
Band
Clampstubing.
used to fasten merchandise
display
tubing.
Havefor
youotused
Have
yousigns
usedto
DXupright
Engineering
clamps
her, nonDX Engineering
for ot
non-antenna
antenna
projects?clamps
We’d love
toher,
know
about it—drop us a
projects?
We’d
love
to
know
about
it—drop
us a note
note and send pictures if you have them!
and send pictures if you have them!
Suggested Hole Size: 0.266" is letter “H” drill bit, 0.332" is letter “Q” drill bit, and 0.397" is letter “X” drill bit. All U-Bolts are formed from premium 18-8 stainless steel.
All Saddles are cast 535 aluminum. All Saddle Clamp Sets are supplied with 18-8 stainless steel nuts and lock washers. Dimensions shown are in inches. Note: These are NOT Automotive Muffler Clamps.
DX Engineering V-Bolt Saddle Clamps
Incorrect
Our V-Bolt Saddle Clamps are sized to fit ranges of tubing. The V-bolts are long enough
to attach tubing or components to thick plates and are highly corrosion-resistant.
The V-Bolt Saddle Clamps are intended for use with a backing plate or mounting plate to
retain the bolt spacing. The saddles’ rippled surface will clamp tubing securely to a flat surface.
Features
• 18-8 stainless steel V-bolts with nuts, flat washers and lock washers
• Cast aluminum saddles with rippled surface
• Available in a number of size ranges
Tubing Recommendations
DXE-CAVS-1P: fits 1/2 inch to 1 3/4 inch O.D. tubing, 1/4"-20 bolt
DXE-CAVS-11P: fits 1/2 inch to 1 3/4 inch O.D. tubing, 5/16"-18 bolt
DXE-CAVS-2P: fits 1 inch to 2 inch O.D. tubing, 5/16"-18 bolt
DXE-CAVS-3P: fits 2 inch to 3 inch O.D. tubing, 3/8"-16 bolt
The clamps are sold only as a set with aluminum saddle, stainless steel V-bolts, nuts, flat washers and lock washers.
The use of a lubricant and sealant, such as Never-Seez®, is highly recommended to achieve proper torque and
prevent galling. For high torque load applications where the tubing is subjected to twisting motion, we recommend
using our U-Bolt Saddle Clamps.
Nominal
Size
DXE Part
Number
D
L
C
I
T
Hole Size
W
0.50 to 1.75
DXE-CAVS-1P
1.75
3.438
1.968
2.313
1/4"-20
0.266 “H”
2.313
0.50 to 1.75
DXE-CAVS-11P
1.75
3.438
2.063
2.313
5/16"-18
0.332 “Q”
2.313
1 to 2
DXE-CAVS-2P
2.00
3.438
2.313
2.000
5/16"-18
0.332 “Q”
2.835
2 to 3
DXE-CAVS-3P
3.13
4.610
3.500
1.750
3/8"-16
0.397 “X”
4.250
H
t
Price
Each
0.250
1
$10.25
0.250
1
$10.75
0.375
1
$12.25
0.500
2
$15.25
All dimensions are in inches. Note: DXE-CAVS-1/11/2P saddle material is cast 535 aluminum, DXE-CAVS-3P saddle material is cast 319 aluminum.
Suggested Hole Size: 0.266" is letter “H” drill bit, 0.332" is letter “Q” drill bit, and 0.397" is letter “X” drill bit. Note: These are NOT Automotive Muffler Clamps.
World-Class Products Shipped Worldwide
Correct
Clamps
DX Engineering Clamps are
Specified by Scientific, Military &
Government Designers, &
Used by Antenna Builders: Both
Commercial & Amateur!
DX Engineering
Super Duty Saddle Clamps
Our Super Duty Saddle Clamps are designed for applications where maximum
clamping ability is needed. Super Duty Saddle Clamp Kits are constructed of two
corrosion-resistant A356-T6 cast aluminum saddles with a cast stainless steel
reinforcement plate. These clamps are the correct size to fit tubing closely and
their rippled surface will grip the aluminum tubing for a secure fit that resists the
ravages of weather.
Due to the wide variety of clamping applications where a Super Duty Saddle Clamp
would be beneficial, we do not include mounting hardware, but we do offer armorcoated bolt sets separately. Super Duty Saddle Clamps are made to fit 3 sizes of tubing:
2 inch O.D., 2.5 inch O.D. and 3 inch O.D.
The use of a lubricant and sealant, such as Never-Seez®, is highly recommended to
achieve proper torque and prevent galling.
Clamps
Part Number
Tube
O.D.
L
W
D
H
C
DXE-SDS-200P
2
3.640
2.000
2.400
2.000
1.570
$34.00
DXE-SDS-250P
2.5
4.150
2.250
2.900
2.500
1.820
$41.00
DXE-SDS-300P
3
4.650
2.500
3.400
3.000
2.060
$51.00
Highest Quality—Lasting Performance!
DX Engineering is famous for its Saddle
Clamps—the ones with stainless steel
U-bolts or V-bolts and matching cast
aluminum saddles. The U-bolts are the
exact size for inch-sized tubing O.D.; the
saddles feature an as-cast roughness that
keeps the tube from sliding.
Our Super Duty Saddle Clamps are
designed for applications where
maximum torque is needed to control
large or unbalanced antenna arrays, or
for other applications where other torque
control products have proven inadequate.
Our Resin Support Blocks are useful
for securely mounting tubing to
any flat surface while providing
electrical insulation.
Whether you are building a Yagi from
scratch, refurbishing a well-used “old
friend,” or experimenting with a new
antenna project, DX Engineering can
supply the best hardware for your
application. You can find useful tips
and complete dimensions for each clamp
and bracket type at DXEngineering.com.
.390
Price
Each
D
W
Plate
Bolt and Nut Sets
Armor-Coated Bolt Sets are available in 5 different bolt lengths (4.5 inch, 5 inch, 5.5 inch,
6 inch and 6.5 inch). They include Grade 8 hex head bolts (2), split washers (2), flat
washers (2) and nuts (2).
DXE-SDSBOLT-4-5 4.5" Bolts ............................................................................ set $5.25
DXE-SDSBOLT-5
5.0" Bolts ............................................................................ set $5.50
DXE-SDSBOLT-5-5 5.5" Bolts ............................................................................ set $5.75
DXE-SDSBOLT-6
6.0" Bolts ............................................................................ set $6.00
DXE-SDSBOLT-6-5 6.5" Bolts ............................................................................ set $6.25
L
Saddle
C
H
Support Block Dimensions in Inches
DX Engineering
Resin Support Block Clamps
Our Resin Support Block Clamps are ideal for securing mounting brackets or plates
to tubing, while also providing electrical insulation. That makes the clamps a good
choice for electronic components. The clamps are sturdy and provide a strong,
well-insulated mounting that is easy to construct. They are available in many sizes
for most any project you might have—see chart.
The Resin Support Block is shown with an optional stainless steel reinforcement
plate. These plates provide additional stiffness and can also be used as sturdy
hole-drilling templates.
W
d
Plate
t
Block
Part Number
Tube
O.D.
H
T
L
W
Reinforcement
Plate Required
Price
Each
1/4
1/4
1.050
1.185
1.350
0.784
DXE-RSB-DP-1
$2.65
DXE-RSB-I03125
5/16
5/16
1.050
1.185
1.350
0.784
DXE-RSB-DP-1
$2.85
DXE-RSB-I03750
3/8
3/8
1.050
1.185
1.350
0.784
DXE-RSB-DP-1
$2.65
DXE-RSB-I05000
1/2
1/2
1.290
1.192
1.595
1.024
DXE-RSB-DP-2
$2.90
DXE-RSB-I06250
5/8
5/8
1.290
1.192
1.595
1.024
DXE-RSB-DP-2
$2.90
DXE-RSB-I03400
3/4
3/4
1.394
1.186
1.910
1.301
DXE-RSB-DP-3
$3.10
DXE-RSB-I10000 1.000 1.000 1.394
1.186
1.910
1.301
DXE-RSB-DP-3
$3.15
DXE-RSB-I11250 1.125 1.125 1.665
1.189
2.258
1.575
DXE-RSB-DP-4
$4.70
DXE-RSB-I12500 1.250 1.250 2.292
1.182
2.760
2.050
DXE-RSB-DP-5
$4.70
DXE-RSB-I11500 1.500 1.500 2.292
1.182
2.760
2.050
DXE-RSB-DP-5
$4.70
DXE-RSB-I13400 1.750 1.750 2.674
1.184
3.394
2.600
DXE-RSB-DP-6
$7.30
DXE-RSB-I20000 2.000 2.000 2.678
1.184
3.394
2.600
DXE-RSB-DP-6
$7.30
DXE-RSB-I22500 2.250 2.250 2.904
1.184
3.394
2.600
DXE-RSB-DP-6
$7.95
Reinforcement Plates Dimensions in Inches
Part Number
D
L
D
DXE-RSB-I02500
DXE-RSB-I11250
H
43
T
Order Online 24/7 at DXEngineering.com
W
Each
DXE-RSB-DP-1
0.275
d
0.119
t
0.784
$3.20
DXE-RSB-DP-2
0.275
0.119
1.024
$3.55
DXE-RSB-DP-3
0.275
0.119
1.301
$3.95
DXE-RSB-DP-4
0.275
0.119
1.575
$4.25
DXE-RSB-DP-5
0.275
0.119
2.050
$4.90
DXE-RSB-DP-6
0.275
0.119
2.600
$5.65
Clamps & Rigid Tubing
Clamps
44
Highest Quality—Lasting Performance! DX Engineering is famous for its
Saddle Clamps—the ones with stainless steel U-bolts or V-bolts and matching
cast aluminum saddles. The U-bolts are the exact size for inch-sized tubing O.D.; the saddles feature an as-cast
roughness that keeps the tube from sliding. Our Super Duty Saddle Clamps are designed for applications
where maximum torque is needed to control large or unbalanced antenna arrays, or for other applications
where other torque control products have proven inadequate. Our Resin Support Blocks are useful for securely
mounting tubing to any flat surface while providing electrical insulation.
Saddle Clamps with
Powdercoated Saddles
ECLS-Series
Band Clamps with Stud
• Stainless steel flat washers,
lock washers, nuts and bolts
• Black powdercoated saddle finish
U-Bolt Style
The ECLS-Series clamps are marine
grade stainless steel with a 10-24
stud welded to the band. They are
ideal for mechanical fastening to
round or odd-shaped members.
The clamps can be used for
electrical connections (including
grounding) or for mechanical assembly of components,
attachment of signs, etc. Threaded hardware is included.
Band Clamps with Stud
Pack of 2
DXE-ECLS-050
0.500" O.D. Tube .........................$9.99
DXE-ECLS-175
1.750" O.D. Tube .......................$11.49
DXE-ECLS-062
0.625" O.D. Tube .........................$9.99
DXE-ECLS-200
2.000" O.D. Tube .......................$11.49
DXE-ECLS-075
0.750" O.D. Tube .........................$9.99
DXE-ECLS-225
2.250" O.D. Tube .......................$11.49
DXE-ECLS-087
0.875" O.D. Tube .......................$10.99
DXE-ECLS-250
2.500" O.D. Tube .......................$11.99
DXE-ECLS-100
1.000" O.D. Tube .......................$10.99
DXE-ECLS-275
2.750" O.D. Tube .......................$11.99
DXE-ECLS-300
3.000" O.D. Tube .......................$11.99
DXE-ECLS-125
1.250" O.D. Tube .......................$11.49
DXE-ECLS-325
3.250" O.D. Tube .......................$11.99
DXE-ECLS-150
1.500" O.D. Tube .......................$11.49
U-Bolt
Part Number
DXE-PSAD-050A
DXE-PSAD-075A
DXE-PSAD-100A
DXE-PSAD-125A
DXE-PSAD-150A
DXE-PSAD-175A
DXE-PSAD-200A
DXE-PSAD-250A
DXE-PSAD-300A
Nominal
Size
Thread
Bolt Size
Price
Each
0.50
0.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
1/4"-20
1/4"-20
1/4"-20
1/4"-20
1/4"-20
1/4"-20
5/16"-18
5/16"-18
5/16"-18
$10.80
$10.95
$11.05
$11.85
$12.75
$13.90
$15.05
$17.05
$18.60
V-Bolt Style
V-Bolt
Part Number
Nominal
Size
Thread
Bolt Size
Price
Each
DXE-PCAVS-1P
DXE-PCAVS-2P
0.50 to 1.75
1.00 to 2.00
1/4"-20
5/16"-18
$10.90
$12.95
Dimensions in Inches.
Our stainless steel V-clamps are ideal
for mounting accessories to steel pipe.
The V-saddle has serrations that
bite into the tube or pipe surface,
providing a strong, secure hold.
For this reason, these clamps are
not recommended for aluminum
tubing or pipe. The bolts supplied
are long enough to attach tubing to thick
plates and have anti-corrosive properties for long
life. Some clamps are available with a tab and 1/4"
hardware for adding grounding wires.
DXE-SSVC-1P
DXE-SSVC-1PG
DXE-SSVC-150P
DXE-SSVC-150PG
DXE-SSVC-2P
DXE-SSVC-3P
Pipe Size
Ground
Lug
Price
Each
1/2" to 3/4"
1/2" to 3/4"
1" to 1.5"
1" to 1.5"
1" to 2"
2.375" to 3"
No
Yes
No
Yes
No
No
$6.95
$7.95
$9.95
$10.95
$11.95
$14.95
Typical elements are built using 0.058 inch
wall tubing, which allows successive sizes
to slide together with good contact. These
clamps are used to hold the telescoping
tubing in place at the length that you have
chosen. Our clamps are marine-grade—they
are made entirely of stainless steel, unlike the
normal hardware store variety. The high nickel
alloy stainless steel meets the demands of severe
corrosive environments.
DXE-ECL-020
For 0.500" and smaller Tube ......$1.90
DXE-ECL-040
For 0.625" Tube ...........................$1.90
DXE-ECL-060
For 0.750" and 0.875" Tube........$1.90
DXE-ECL-10SS
For 1.00" Tube .............................$1.90
DXE-ECL-12SS
For 1.250" and 1.125" Tube........$1.90
DXE-ECL-16SS
For 1.375" and 1.500" Tube........$1.90
DXE-ECL-20SS
For 1.625" and 1.750" Tube........$1.90
DXE-ECL-24SS
For 1.875" and 2.000" Tube........$1.90
DXE-ECL-28SS
For 2.125" and 2.250" Tube........$1.90
DXE-ECL-32SS
For 2.375" and 2.500" Tube........$1.90
DXE-ECL-36SS
For 2.625" and 2.750" Tube........$1.90
DXE-ECL-40SS
For 2.875" and 3.000" Tube........$1.90
DXE-ECL-44SS
For 3.25" Max. Tube ....................$1.95
Ridgid® Tubing Cutter
DXE-CPC-375
Cushioned
P-Clamps
DXE-CPC-250
DX Engineering P-Clamps are ideal for providing strain
relief of coaxial cable connections. The rubber insert
grips the cable jacket securely without nicking or cutting
the jacket, preventing water entry.
DXE-CPC-250
For RG-8X, RG-6, RG-59 Cable,
Pack of 10...................................$14.95
DXE-CPC-375
For RG-213, RG-8, RG-11 Cable,
Pack of 10...................................$14.95
DXE-UT-2125
If you’re building a tower, mast
or beam antenna, these tools will
be worth their weight in gold.
They make the tedious deburring
process much easier. These tools
smooth the rough edges on the
inside and outside of your telescoping
aluminum, fiberglass, copper, steel
or plastic pipe and tubing, assuring
a smooth surface when joined with
DXE-UT-3500
another section.
You can purchase each tool separately or together in
a kit that includes both deburring tools, a small hand
deburring tool, half-round file and a carrying case.
DXE-UT-2125
Deburring Tool, for
.375" to 2.125" O.D. Tubing ......$24.95
DXE-UT-3500
Deburring Tool, for
1.875" to 3.5" O.D. Tubing ........$29.95
DXE-UT-KIT-DBR Deburring Tool Kit.....................$69.95
Stainless Steel
Element Clamps
DX Engineering
Stainless Steel V-Clamps
V-Clamp
Part Number
Pipe and Tube Deburring Tools
This high-quality cutter will make clean,
smooth edges in tubing sections that
require minimal deburring. The tool can
cut aluminum, copper, and brass tubing
as well as thin-wall conduit.
• Adjustable from 1/4 inch to 1 1/8 inch O.D.
• Telescoping feed screw design
• Enclosed feed screw eliminates clogging
• Grooved rollers for close-to-flare cuts
• Fold-away reamer
• X-CEL knob and pin for quicker cutting
• Spare cutter wheel included
DXE-31622
Ridgid Tubing Cutter.............$41.95
Proven Products, Expert Advice, Same-Day Shipping
Drill Guide Kit
This easy-to-use drill guide locates
exact drilling centers and guides
drill bits perfectly perpendicular
to the work piece, including round,
spherical, and corner edges. It is
ideal for making clean, accurate holes in
aluminum tubing for mounting hardware.
The kit includes 3/16 inch, 1/4 inch, 5/16 inch,
3/8 inch, 7/16 inch, and 1/2 inch drill bushings, a
locating pin, and drill bit guide.
DXE-D3206
Drill Guide Kit ............................$15.25
Deburring Tools
Adjustable Length Deburring Tool
DXE-22600
Deburring Tool ..........................$13.95
DXE-22110
Replacement Blades for Aluminum/
Steel, Pack of 10 ........................$10.75
Slim Grip Deburring Tool
DXE-22166
Slim-Grip Deburring Tool ...........$7.55
DXE-22110
Replacement Blades, 10 Pack; $10.75
Never-Seez®
and Anti-Seize—a
Must for Stainless Steel
• Prevents galling and
galvanic corrosion
• Protects metal parts against rust, corrosion and seizure
DXE-NSBT8
Never-Seez, 8 oz. Brush Top .......$13.99
DXE-NMCBT8
Never-Seez, Marine Grade,
8 oz. Brush Top .............................$16.95
UMI-81343
Anti-Seize, 1 oz. Squeeze Tube ..... $3.29
UMI-81464
Anti-Seize, 8.5 oz. Aerosol Can ..... $9.99
Hazardous, limited to domestic UPS Ground shipping only.
Penetrox A
• Keeps parts from seizing
• Helps create a substantial electrical
connection between metal parts
• For aluminum-to-aluminum or
aluminum-to-copper connections
DXE-P8A
Penetrox A,
8 oz. Squeeze Tube.....$13.95
Hazardous, limited to domestic UPS Ground shipping only.
Rigid Tubing
45
Aluminum Tubing
Custom-made for DX Engineering, this high strength Type 6063-T832
seamless drawn aluminum tubing is available in 3 and 6 foot
lengths—ideal for your antenna projects. Type 6063 alloy provides
good resistance to general corrosion, including stress
corrosion cracking, and has excellent surface appearance.
Use the 3 foot lengths for fast taper, low-wind resistance
applications. The 6 foot slow taper lengths afford the
greatest bandwidth. Most sizes are slit on one end
for use with DX Engineering Stainless Steel Element
Clamps. If unslit ends are required for your application, merely insert the slit end into the next larger size
in the stack and use your own attachment method.
The 0.058 inch wall tubing is available in 1/8 inch
increments from 3/8 inch to 2 1/8 inch O.D. It is ideal for
a free, yet solid telescoping fit from size to size for vertical or
Yagi elements. Some larger sizes are available in 0.120 inch wall,
6061-T8 aluminum, which assures maximum strength at
Aluminum Tubing Slit 1 End
very long assembly lengths.
• High strength Type 6063 seamless aluminum tubing—
drawn, not extruded
• Ideal for telescoping antenna elements,
support masts, and booms
• Available in unslit and pre-slit lengths
• Use DX Engineering Stainless Steel Element
Clamps to assemble lengths of slit tubing
DX Engineering Has Stainless Steel Element Clamps
for Exact Tubing Sizes. See DXEngineering.com for
Specs and Additional Tubing.
Aluminum Tubing, No Slit
Part Number
O.D.
Wall
Length
Each
DXE-AT1240
DXE-AT1494
DXE-AT1495
DXE-AT1496
DXE-AT1497
DXE-AT1498
DXE-AT1499
DXE-AT1500
DXE-AT1501
DXE-AT1502
DXE-AT1503
DXE-AT1504
DXE-AT1505
DXE-AT1506
DXE-AT1255
DXE-AT1507
DXE-AT1189
DXE-AT1480
DXE-AT1481
DXE-AT1482
DXE-AT1483
DXE-AT1484
DXE-AT1485
DXE-AT1486
DXE-AT1487
DXE-AT1488
DXE-AT1489
DXE-AT1490
DXE-AT1491
DXE-AT1492
DXE-AT1493
0.375"
0.500"
0.625"
0.750"
0.875"
1.000"
1.125"
1.250"
1.375"
1.500"
1.625"
1.750"
1.875"
2.000"
2.000"
2.125"
0.375"
0.500"
0.625"
0.750"
0.875"
1.000"
1.125"
1.250"
1.375"
1.500"
1.625"
1.750"
1.875"
2.000"
2.125"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.120"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
$1.45
$2.05
$2.35
$2.65
$2.75
$2.95
$3.25
$4.15
$4.45
$5.25
$6.05
$6.85
$7.65
$8.45
$14.85
$9.25
$2.95
$4.15
$4.75
$5.35
$5.65
$5.95
$6.55
$7.75
$8.45
$8.95
$9.75
$10.65
$11.55
$12.45
$13.35
DX Engineering Fiberglass Tubing
Part Number
O.D.
Wall
Length
Each
DXE-AT1241
DXE-AT1242
DXE-AT1243
DXE-AT1244
DXE-AT1245
DXE-AT1246
DXE-AT1247
DXE-AT1248
DXE-AT1249
DXE-AT1250
DXE-AT1251
DXE-AT1252
DXE-AT1253
DXE-AT1254
DXE-AT1205
DXE-AT1206
DXE-AT1207
DXE-AT1208
DXE-AT1209
DXE-AT1210
DXE-AT1211
DXE-AT1212
DXE-AT1213
DXE-AT1214
DXE-AT1215
DXE-AT1216
DXE-AT1217
DXE-AT1218
0.500"
0.625"
0.750"
0.875"
1.000"
1.125"
1.250"
1.375"
1.500"
1.625"
1.750"
1.875"
2.000"
2.125"
0.500"
0.625"
0.750"
0.875"
1.000"
1.125"
1.250"
1.375"
1.500"
1.625"
1.750"
1.875"
2.000"
2.125"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
0.058"
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
3 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
$3.75
$4.05
$4.35
$4.45
$4.65
$4.95
$5.85
$6.15
$6.95
$7.75
$8.55
$9.35
$10.15
$10.95
$6.05
$6.65
$7.25
$7.55
$7.85
$8.45
$9.65
$10.35
$10.85
$11.65
$12.55
$13.45
$14.35
$15.25
6061-T8 Aluminum Tubing, Heavy Wall, Unslit—Ideal for
Booms and HD Element Designs!
Part Number
O.D.
Wall
Length
Each
DXE-AT1311
DXE-AT1312
DXE-AT1313
DXE-AT1314
DXE-AT1315
DXE-AT1316
DXE-AT1317
DXE-AT1325
1.500"
1.750"
2.000"
2.250"
2.500"
2.750"
3.000"
3.000"
0.120"
0.120"
0.120"
0.120"
0.120"
0.120"
0.120"
0.120"
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
6 Foot
12 Foot
$23.85
$28.20
$33.00
$37.45
$42.50
$46.95
$51.40
$103.95
DX Engineering 1/8" wall extruded fiberglass tubing is
available in telescoping lengths. The strong 8 foot lengths
are ideal for building your own antenna support, like
quad spreaders and insulated UHF stacking frames—
even push-up masts.
The optional slit ends are ideal for clamping without
drilling (drilling weakens the tubing). Don’t forget
DX Engineering Stainless Steel Element Clamps for a
final, long-lasting assembly or easy-to-assemble
portable installation.
Telescoping Fiberglass Unslit Tubing
Part Number
O.D.
Wall
Length
Each
DXE-FT0500-8
DXE-FT0750-8
DXE-FT1000-8
DXE-FT1250-8
DXE-FT1500-8
DXE-FT1750-8
DXE-FT2000-8
DXE-FT2250-8
DXE-FT2500-8
DXE-FT2750-8
0.500"
0.750"
1.000"
1.250"
1.500"
1.750"
2.000"
2.250"
2.500"
2.750"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
$6.45
$8.95
$9.95
$11.95
$18.95
$20.95
$25.95
$34.95
$38.95
$44.95
Telescoping Fiberglass Tubing with 1 End Slit
Part Number
DXE-FT0750-8S
DXE-FT1000-8S
DXE-FT1250-8S
DXE-FT1500-8S
DXE-FT1750-8S
DXE-FT2000-8S
DXE-FT2250-8S
DXE-FT2500-8S
DXE-FT2750-8S
O.D.
Wall
Length
Each
0.750"
1.000"
1.250"
1.500"
1.750"
2.000"
2.250"
2.500"
2.750"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
0.125"
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
8 Foot
$13.95
$14.95
$16.95
$23.95
$25.95
$30.95
$39.95
$44.95
$49.95
Telescopic
Aluminum Mast
Perfect for stealth operation, this mast can quickly
extend from a mere 4.5 feet to almost 15 feet. It handles
antennas up to 22 pounds and features a guy bracket
(45 feet of guy line is included) to keep it rock-steady
when extended. The mast’s top tube is .875" O.D. and
the bottom tube is 1.625" O.D., all in portable package
that only weighs three pounds.
CMA-CP-45
Telescopic Aluminum Mast.......$99.95
Aluminum Tripod
The perfect companion to your Telescopic Aluminum
Mast, this portable tripod is an easy way to get on the air
for Field Day or EMCOMM. It can handle a guyed mast up
to 55 inches long while supporting 22 pounds of antenna
load.
CMA-YS-45
Aluminum Tripod....................... $119.95
Guy Rings
You can use DX Engineering’s newly engineered Guy Rings to secure your rope guys and stabilize your DX Engineering,
Hustler or other aluminum vertical antenna. They’re also great for our Telescoping Fiberglass and Aluminum Tubing Kits.
These guy rings are super strong, virtually impervious to the elements and fit 0.75", 1.0", 1.25", 1.50" and 2.0" O.D. tubing.
For all the specs, please visit DXEngineering.com.
DXE-GR-5P
Guy Rings, Set of 5 .........................................................................................................................$7.95
Need Advice? 1-330-572-3200 or DXEngineering@DXEngineering.com
46
Towers
Phillystran®
Non-Metallic
Tower Guy Line
These insulator-free, non-metallic guys have been protecting the towers of knowledgeable amateur radio operators since 1973. Following their introduction, Phillystran Guy
Lines have been installed on more than one thousand commercial broadcast towers
worldwide. Electrically transparent Phillystran tower guys are protected by an extruded
jacket, providing excellent resistance to weather and abrasion.
• Complete isolation of tower-guy system from the antenna field
• Improved signal coverage, eliminating distortion caused by re-radiated signals
• Quick, easy, maintenance-free tower installations
• A neat tower appearance, free of corroded steel guys and troublesome ceramic
insulators (solving arcing white noise issues, too)
• No need to calculate guy lengths to avoid guyline resonance
• No insulators required
• None of the stretching or aging problems associated with conventional synthetic ropes
• Never again be bothered by zapping, snapping and crackling across porcelain
insulators
PHI-HPTG-1200I
4mm Dia., 1,200 Lbs. Break Strength ......................per foot $0.49
PHI-HPTG-2100I
6mm Dia., 2,100 Lbs. Break Strength ......................per foot $0.75
PHI-HPTG-4000I
8mm Dia., 4,000 Lbs. Break Strength ......................per foot $0.99
PHI-HPTG-6700I
9mm Dia., 6,700 Lbs. Break Strength ......................per foot $1.39
PHI-HPTG-11200I 11mm Dia., 11,200 Lbs. Break Strength ..................per foot $2.39
Phillystran® Big Grip Dead-Ends
Phillystran has answered the call for field-installable, nonmetallic tower-guy systems
with HPTG-I and PLP Big Grip Dead-Ends. Phillystran Big Grip Dead-Ends
have a variety of unique features:
• Grip designed to match rope twist direction (RHL)
• Special-sized wires for ease of application
• Galvanized steel and “C” coat construction
• Color-coded for ease of identification
• Longer length to match Phillystran’s
high performance Forged steel
galvanized wire rope clips are
recommended for the small PHI-HPTG-1200I Guy Line
DXE-6990334
3/16" Wire Rope Clip, Use with HPTG-1200I ............................... $3.29
PHI-PLP-2738 Blue Tag, use with HPTG-2100I Guy Line .................................... $9.00
PHI-PLP-2739 Yellow Tag, use with HPTG-4000I Guy Line ............................... $12.00
PHI-PLP-2755 Red Tag, use with HPTG-6700I Guy Line ................................... $18.00
PHI-PLP-2558 Black Tag, use with HPTG-11200I Guy Line .............................. $21.00
Galvanized Thimbles Phillystran® Guy Line
Extra heavy-duty, hot-dip galvanized steel for strength and long life.
DXE-1037639
Use with HPTG-1200I Guy Line ..................$0.95
DXE-1037675
Use with HPTG-2100I Guy Line ..................$1.45
DXE-1037693
Use with HPTG-4000I Guy Line ..................$2.45
DXE-1037719
Use with HPTG-6700I/11200I Guy Line......$3.45
Vinyl End Caps Phillystran® Guy Line
Heavy-duty vinyl to cover and protect cut cable ends. 20 per pack.
DXE-H166
Use with HPTG-1200I Guy Line ...................... $5.95
DXE-H165
Use with HPTG-2100I Guy Line ...................... $5.95
DXE-H164
Use with HPTG-4000I Guy Line ...................... $5.95
DXE-H142
Use with HPTG-6700I Guy Line ...................... $5.95
DXE-H204
Use with HPTG-11200I Guy Line .................... $5.95
Accessory Items for Phillystran® Guy Line
Cable
Price Per Foot
PHI-HPTG-1200I...$0.49
PHI-HPTG-2100I...$0.75
PHI-HPTG-4000I...$0.99
PHI-HPTG-6700I...$1.39
PHI-HPTG-11200I;$2.39
Big Grip
Price Each
PHI-PLP-2738.....$9.00
PHI-PLP-2739...$12.00
PHI-PLP-2755...$18.00
PHI-PLP-2558...$21.00
Thimble
Price Each
DXE-1037639...$0.95
DXE-1037675...$1.45
DXE-1037693...$2.45
DXE-1037719...$3.45
DXE-1037719...$3.45
3/16" Wire Rope Clip
Forged steel galvanized wire rope clips are recommended
for the small 3/16" Guy Line. Made from extra heavy-duty,
galvanized, forged carbon steel, for 3/16" wire rope.
A minimum of 2 clips is required.
DXE-6990334
3/16" Wire Rope Clip, Use with HPTG-1200I ... $3.29
End Cap
Price 20 Pack
DXE-H166...$5.95
DXE-H165...$5.95
DXE-H164...$5.95
DXE-H142...$5.95
DXE-H204...$5.95
50 Foot Telescoping
Fiberglass Tubing Mast Kit
• Custom-made tubing
for DX Engineering
• Smoothly telescoping
• Neutral light gray color
• Includes DX Engineering
Stainless Steel Element
Clamps to assemble slit lengths
DXE-FTK50
Telescoping Tubing Kit ........ $138.00
Telescoping
Aluminum Antenna Kit
• Eleven telescoping sections from
2" to 7/8" O.D.
• Stainless steel element clamps
DXE-ATK65
Telescoping Aluminum
Antenna Kit ...............................$194.50
DXE-VE-BASE Vertical Antenna Fixed
Base Assembly ........................... $99.50
DXE-VA-BASE Vertical Antenna Heavy-Duty
Tilt Base Assembly ...................$159.95
Telescoping Masts
Rohn telescoping masts are available in 28', 34', 36'
and 43' nominal heights. They are pre-galvanized
for corrosion protection and come assembled with
hardware. All masts must be guyed or bracketed; installation should
be done by experienced professionals. Telescoping masts are not
recommended for commercial, CB or beam antenna installations.
ROH-H30 28' Telescoping Mast .................................................................$79.95
ROH-H40 36' Telescoping Mast ...............................................................$119.95
ROH-H50 43' Telescoping Mast ...............................................................$144.95
ROH-9H50 34' Telescoping Mast, UPS-shippable ...................................$129.95
Guy Tools
You’ve got a lot of money invested in your mast and antenna, and you’ve selected
reliable guy line—now the weak link in mast stability could literally be your links!
Gripple is an industry leader in wire joiners and tensioners, offering professional-grade
products that have been fully vetted in practically every environment on Earth. When it
comes time to erect your mast, don’t overlook the importance of having the right tools
and grips for the job.
Cable Cutters
Cutting steel cables and guy lines
is no easy task. Gripple offers the
tools to make it manageable. Made
with hardened jaws for durability and
vinyl grips for comfort, they are designed to be the only cutters
you’ll ever need. The innovative design multiplies your own strength to make cuts clean
and effortless.
The Regular Cable Cutter can handle cutting up to 3/16" O.D. EHS steel cable. The Large
Cable Cutter is designed for cutting cable up to 1/4" diameter.
GPL-CUTTER-1-4
Large Cable Cutter ............................................................. $95.95
GPL-CUTTERGRIPPL Regular Cable Cutter ......................................................... $35.95
Lockable Guy Line Grip and Key
As an easy way to assemble and re-tension your 1/8"
EHS guy line, you can use these grips and keys to
terminate cable and keep it secure. The Grip’s innovative
design uses external pressure to lock the cable in place until
you use the key to release it, making them easy to install and adjust.
They’re tailored to .125" (3mm) guy lines.
The Lockable Release Keys are a must for re-tensioning cables and removing the
grips. You just inset the key and push; the internal wedges are released and the grip
is free. Choose from the ergonomically designed Logo Key or the high-visibility
Flag-Shaped Key.
GPL-LK-1-8-160BB Lockable Guy Line Grip ........................................................... $5.95
GPL-KEY-FLAG
Lockable Release Key, Flag..................................................... $0.95
GPL-KEY-LOGO
Gripple Logo Setting Key ........................................................ $3.99
More Products, Specs and Photos at DXEngineering.com
Towers
47
Rohn Commercial Towers DX Engineering is now an Authorized Distributor of Rohn
Commercial Tower products and accessories. We have the Rohn products you need to
solve your tower structural needs—contact us for technical information and availability.
Shipping the Big Stuff
DX Engineering will arrange to ship larger tower
sections and masts to you for an additional truck
freight fee. The fee depends on the product you’ve
ordered. So even if you’ve ordered a large item,
you can expect it to get to your door quickly.
Heavy-Duty
Tripod Roof Mount
This five foot tall, commercial-strength mount is
an ideal support for medium size antennas such
as the DX Engineering HEXX Beam. The mount
is also a good choice for small HF or VHF Yagi
or tri-band antennas as well as HF and VHF
vertical antennas.
The tall tripod configuration allows peak
mounting on a variety of pitched or flat roofs.
The 1.5" O.D. steel legs have two 10 inch long
mounting feet each. Each mounting foot is
secured with five lag bolts. Thirty lag bolts
are supplied, along with tar strips
for weatherproofing under each foot.
A five foot long, 2" O.D. steel
antenna/rotor mounting mast is
also furnished for easy mounting of
rotors such as the Hy-Gain CD-45II
and HAM-series.
RON-1011 Heavy-Duty 5' Tripod
Roof Mount...$149.95
Rotor-Ready Heavy-Duty
Chimney Roof Mount
Use this ready-to install package
for chimney mounting medium size
antennas with rotors (such as the
DX Engineering HEXX Beam)
and small HF or VHF Yagis and
tri-banders. The mount is also ideal
for HF and VHF vertical antennas
with no rotors.
Two sections of 1.5" O.D., 16-gauge steel
mast are supplied. The 42" long section is preassembled
with chimney corner brackets for fastening to the
chimney and antenna/rotor mounting. The 24" long
section is for mounting the antenna to the upper bracket
of a rotor such as the Hy-Gain CD-45II and HAM-series.
The four chimney corner brackets are 1.5" wide
11-gauge steel. The stainless steel fastening straps are
24 feet long, more than long enough for multiple-flue
residential and even commercial chimneys. Shipped
partially assembled for quick installation.
RON-3324 Heavy-Duty Chimney Roof Mount ...$149.95
Feature a universal mast
clamp that is capable
of mounting masts with
up to 1.75 in. diameters
and bolt-on swivel feet
that adjust to the pitch
of almost any roof. Installation is simple
and fast with lag screws (not included) in the base feet
that securely anchor the towers for long, trouble-free
service. Rohn tripod roof towers feature a lower mast
support bracket, hot-dip galvanized construction for
corrosion protection, and prevailing torque locknuts on
the bolt-on feet.
ROH-TRT36
Tripod Roof Tower, 3'................$49.95
ROH-TRT60
Tripod Roof Tower, 5'................$64.95
Adjustable House Brackets
Perfect for bracing your lightly guyed or self-supporting
Rohn 25G series tower, these adjustable brackets let
you compensate for eaves and overhangs. They’re great
solutions if your community requires all self-supported
or guyed towers to be bracketed.
Wall Clearance
Adjustable 0-24"
Adjustable 0-15"
Adjustable 0-36"
Part Number
ROH-618
GPL-LK-1-8-160BB
ROH-3-16EHS500
ROH-3-16EHS1000
ROH-1-4EHS500
Tripod Roof Towers
Part Number
ROH-HB25BG
ROH-HB25AG
ROH-HB25CG
Rohn 55G
50' Fold-Over Tower
The top of the 55G can be
lowered down to ground
level so maintenance and
ROH-55FK-50LAB
replacements can be performed
at a comfortable and safe working level without climbing
to dangerous heights. When the work is complete, the
tower is easily returned to the upright position and
locked into place. You never have to leave the ground!
The Rohn 55FK design is based on 90 mph winds with no
ice. 20', 30', 40', and 60' tall towers are also available.
ROH-55FK-50LAB 55G Fold-Over Assembly... $7,599.95
ROH-45GSRSB
45GSR Concrete Base,
Short 4.29' ..............................$479.95
Erection Fixture
You probably call this a Gin Pole, it is a must-have tool
to safely raise or repair your tower. The fixture is
designed for 25G or 45G towers. It has the correct sheave
and clamps to do the job right, you supply the rope
and muscle.
ROH-EF2545 Erection Fixture ............................$899.95
Work Platform
Don’t get your feet stuck in the cross-bracing, install this
platform on your 25G Tower and perform your repairs
safely. Snaps into place and lets you work without strain.
ROH-WP25G Work Platform ..............................$139.95
Telescopic Mast Ground Mount
Built for your Rohn H and 9H (or any other 1.25"-1.5"
telescopic mast), simply drive this ground mount into
the soil, add your guy lines and get on the air.
ROH-GTMBL Ground Mount ................................$49.95
Turnbuckle
Never trust your guy line tension to an average hardware
store turnbuckle. Only use genuine Rohn accessories.
This turnbuckle has a 1,200 pound working load with an
extended/retracted length of 12/18 inches.
ROH-3-8TBE-J Turnbuckle .....................................$39.95
Installation Accessories
Width
25"
25"
30"
Price
$135.95
$99.95
$144.95
ROH-BG2142
ROH-BG2144
ROH-GAC3455TOP
ROH-GAR30
ROH-GAS604
ROH-EP25343
ROH-EP25345
ROH-TB3
ROH-TB4
ROH-25AJBK
ROH-45JBK
ROH-HBUTVRO
ROH-3-4X12PP
Description
6-Strand 18 AWG
Wire, 1,000' Reel
618/620 Wire Gripple
HDG Guy Wire,
3/16" EHS x 500' Coil
HDG Guy Wire, 3/16"
EHS x 1,000' Coil
HDG Guy Wire,
1/4" EHS x 500' Coil
Big Grip, 3/16" with
End Sleeve
Big Grip, 1/4" with
End Sleeve
Anchor Rod, 3455,
.75" dia. x 7'
Anchor Rod, Eye,
Rated to 7,330 lbs.
Screw Anchor
Equalizer Plate
Assembly 25, 3-Hole
Equalizer Plate
Assembly 25, 5-Hole
HD Thrust Bearing
for 25G, 45AG, 55AG
HD Thrust Bearing
for 45AG, 55AG
25AG Joint Bolt Kit
45G Joint Bolt Kit
Universal HD House
Bracket, 18-36"
Standoff for
25G, 45G, 55G
Base Pier Pin, 3/4" x
12"- 25G, 45G, 55G
Price
$95.95
$5.95
$124.95
$249.95
$182.00
$11.95
$13.95
$119.95
$41.95
$64.95
$45.95
$59.95
$149.95
$179.95
$6.95
$11.95
$234.95
$22.95
The World Leader in Towers
Rohn has been the world leader in
tower design and manufacturing
for more than six decades. Rohn
maintains one of the largest
manufacturing and staging facilities
in the industry—it is committed to
supplying the best.
Designed for areas where land
cost or availability are not an
issue, Rohn GT Series guyed
towers provide one of the most cost
effective solutions in the industry.
Guyed towers install quickly and
are often the choice of broadcast
communications tower stations and
backbone system providers.
All GT Series towers are built with
high strength steel tubing that is
hot-dip galvanized after fabrication.
Rohn’s exclusive Zig-Zag® solid rod bracing provides
exceptional strength.
All Rohn towers, poles and masts must be installed and
dismantled by trained personnel. See the Rohn manuals
and drawings for detailed information.
25G Tower and Accessories
The Model 25 originated at Rohn and the original
still stands as the benchmark of lightweight
guyed tower design quality. The 25G is available
in the standard 10' section length and in a special
order, UPS-shippable 7' length. The 25G uses
double-bolted joints—proven to be the best
method of joining tower sections for sturdiness
and dependability. The 25G stands 190' tall.
• Completely hot-dip galvanized after fabrication
• Built on a stable 11.25" equilateral triangle design
• High strength tubular legs joined by
Zig-Zag® crossmembers
• Each section length is shipped with all required nuts
and bolts
• Continuous solid round steel bracing
ROH-25G
25G Standard Section, 10' ...........$117.95
ROH-25AG2
25G Top Section,
accepts 2" O.D. Mast.....................$189.95
ROH-SB25G5 25G Short Base, 5'...........................$99.95
ROH-SB25G 25G Short Base, 3.33' .....................$72.95
ROH-25GSSB 25G Self Supporting Base Plate ...$179.95
ROH-BPH25G 25G Hinged Base Plate .................$279.95
ROH-SBH25G 25G Short Hinged Base, 3.33' ......$229.95
ROH-SDB25G Drive-In Base Plate for
Temporary Use..............................$254.95
ROH-AS25G 25G Top Single Accessory Shelf.....$52.95
ROH-GA25GD 25G Guy Bracket Assembly
with Hardware ..............................$159.95
ROH-UHF25G 25G Side Arm Mount.......................$31.95
ROH-BPC25G Concrete Base Plate for 25G ..........$68.95
45G Tower and Accessories
The 45G is a true multi-use structure that provides
excellent strength for applications up to 300' tall.
• Completely hot-dip galvanized after fabrication
• Built on a stable 16.75" equilateral triangle design
• High strength tubular legs joined by
Zig-Zag® cross members
• Continuous solid round steel bracing
• Each section is shipped with all required nuts and bolts
ROH-45G
45G Standard Section, 10'...........$234.95
ROH-45AG
45G Top Section, 9' ......................$299.95
ROH-SB45G
45G Short Base, 5' ........................$119.95
ROH-BPL45G 45G Top Plate for TB3 &
TB4 Bearings ................................$219.95
ROH-BPC45G 45G Concrete Base Plate .............$119.95
ROH-AS455G 45G & 55G Accessory Shelf ..........$112.95
ROH-GA45GD 45G Guy Bracket Assembly
with Hardware..............................$149.95
FREE Standard SHIPPING for Orders Over $99, See Page 58 for Details
48
Antennas: Hardware
DXE-BEP-4B
Insulated
Boom-to-Element Brackets
DXE-BEB2 to Tower Leg
DX Engineering offers insulated
boom-to-element brackets to fit
1.75 inch, 2 inch and 3 inch booms.
The non-metallic brackets electrically
insulate the elements from the boom,
which virtually nullifies the shortening
effect that the boom and the normal
metallic boom-to-element plates
have on element length. This means
the element lengths determined
through the use of commonly available
antenna design programs like YO,
EZNEC and others will correspond
more closely to the actual lengths
needed. In most cases, the cost of the
boom-to-element brackets will be less
than using a metallic plate and the
necessary saddle clamps.
(Mounting plate
customer supplied)
DXE-BEB-1
DXE-BEB-1
The DXE-BEB-1 is used to replace KLM or equivalent
boom-to-element brackets or for any other application
where insulated elements are desired. This patented
DX Engineering bracket is made from a much stronger
material and has a vastly improved design. It is 5 times
as strong as the original brackets and allows use of up to
1.25 inch O.D. element tubing. Use the DXE-ELA-1-2
Element Adapters to use a 1 inch diameter element with
the DXE-BEB-1.
The DXE-BEB-1 is designed to use DX Engineering’s Gorilla Grip™ stainless steel boom
clamps that will end all of your concerns about elements rotating on the boom.
DX Engineering offers two hardware kits. The standard kit is a direct KLM hardware
replacement with #10 fasteners for the elements. It includes Gorilla Grip™ stainless steel
boom clamps, stainless steel bolts with nuts and washers to attach clamps to the
DXE-BEB-1 element bracket, and stainless steel bolts with nuts and washers to attach
elements or adapters to the element brackets. The nuts have nylon inserts and are
vibration-resistant. The heavy-duty kit uses 1/4 inch bolts and hardware, so it is not a
direct replacement for KLM brackets, but is similar in all other respects to the standard
hardware kit.
DXE-BEB-1
Insulated Boom-to-Element Bracket, 3" Boom ............. $49.95
DXE-BEB-1HWK
KLM Direct Replacement Hardware Kit .......................... $25.95
DXE-BEB-1HWK-2
Hardware Kit with 1/4" Bolts ........................................... $25.95
DXE-ELA-1-2
Element Adapters, 1.25" to 1", for DXE-BEB-1 .................. $9.95
Boom-to-Element Plates
Boom-to-element plates are similar in
function to insulated boom-to-element brackets,
in that they each attach the elements to the boom.
The primary advantage of plates over brackets is that
it is a simple mechanical arrangement. The main
disadvantage is that the plate does not insulate the element
from the boom, which means that the element dimensions
that you bring from your antenna design program
(YO, AO, EZNEC and others) will be incorrect unless
you make some length adjustment for the width of the plate and boom.
DXE-BEP-4B
Fabricated from alloy 6061-T6 aluminum, the DXE-BEP-4B is primarily for the smaller
6 meter, 10-12 meter and 17-15 meter beam. This plate can also be used to mount
smaller VHF/UHF antennas to a mast using appropriate clamps. The dimensions of
the DXE-BEP-4B are 8 inch L x 3.5 inch W x 0.25 inch T. This plate comes pre-drilled for
DX Engineering Saddle Clamps.
• For mounting a 2 inch boom use (2) DXE-SAD-200A Clamps
• For mounting a 1.50 inch boom use (2) DXE-SAD-150A Clamps
• For mounting a 1.25 inch grounded element use (2) DXE-SAD-125A Clamps
• For mounting a 1 inch grounded element use (2) DXE-SAD-100 Clamps
• For mounting a 3/4 inch grounded element use (2) DXE-SAD-075 Clamps
DXE-BEP-5B
Fabricated from alloy 6061-T6 aluminum, the
DXE-BEP-5B is for the larger 17-15 meter and 20
DXE-BEP-5B
meter beams. This plate can also be used to mount
smaller VHF/UHF antennas to a mast using appropriate clamps. The dimensions of the DXE-BEP-5B are
8 inch L x 3.5 inch W x 0.25 inch T. The plate comes
pre-drilled for DX Engineering saddle clamps.
• For mounting a 3 inch boom use (2) DXE-SAD-300A Clamps
• For mounting a 2 inch boom use (2) DXE-SAD-200A Clamps
• For mounting a 1.50 inch grounded element use (2) DXE-SAD-150A Clamps
• For mounting a 1.25 inch grounded element use (2) DXE-SAD-125A Clamps
• For mounting a 1 inch grounded element use (2) DXE-SAD-100 Clamps
DXE-BEP-4B
Boom-to-Element Plate, 1.5" or 2" booms ......................... $19.45
DXE-BEP-5B
Boom-to-Element Plate, 2" or 3" booms ............................ $20.45
These brackets are made for 3 inch O.D. booms only. For 2 inch booms, please use DXE-BEB-2.
Multi-Purpose Mounting Plates
DXE-BEB-2
The DXE-BEB-2 is made from an extremely
strong polymer that is also highly UVresistant. When bolted to your 2 inch boom
with our hardware kit, it will easily support a
split 20 meter element without a fiberglass
centerpiece. It is a convenient, low-cost
DXE-BEB-2
method for the insulated attachment of
elements when building Yagi, LPDA or other antennas on 2 inch booms.
It accepts up to a 7/8 inch element, which is suitable for antennas built for 6 meters up
thru 20 meters with reasonable wind survivability. For larger antennas, please use our
DXE-BEB-1 Boom-to-Element Bracket.
The DXE-BEB-2 comes in 2 pieces and bolts together with a DXE-BEB-2HWK Stainless
Steel Hardware Clamp Kit that also holds it securely to the boom. The hardware kit
includes four stainless steel bolts, washers and lock nuts that securely clamp the
element halves together, and a Gorilla Grip™ stainless steel boom clamp with the
stainless steel bolts, nuts and washers that attach it to the element bracket. Nuts are
vibration-resistant with nylon inserts. DXE-BEB-2HWK Hardware Kit for the DXE-BEB-2
Bracket is sold separately. Larger antennas that experience high winds will require the
boom clamp to be pinned to the boom.
DXE-BEB-2
Insulated Boom-to-Element Bracket, 2" Boom ................... $16.95
DXE-BEB-2HWK
Hardware Kit for DXE-BEB-2 .................................................. $13.95
These universal mounting plates can be used for
DXE-UMP-1
many applications. They are available in aluminum
or non-conductive black polymer and come blank
or pre-drilled to accept our standard DXE-CAVS-1P
V-Saddle Clamps, which can accommodate tubing
or pipe from 1/2 inch to 1.75 inch O.D.
If you are looking for larger sizes, one of our
Boom-to-Mast Plates may work. They are available
DXE-UMP-2
for 1.75 inch, 2 inch, and 3 inch O.D. tubing or
pipe. Visit DXEngineering.com for the clamps
recommended for use with each specific plate.
DXE-UMP-1
Universal Mounting Plate for 1.75" Saddle Clamp ............. $15.00
DXE-UMP-2
Universal Mounting Plate for 2" Saddle Clamp .................. $15.00
DXE-MMP-P2
Non-Conductive Blank Polymer Plate,
1/4" x 7.5" x 11.5" .................................................................... $7.50
DXE-MMP-P3
Non-Conductive Blank Polymer Plate,
1/4" x 7.5" x 16" ....................................................................... $9.90
DXE-BEB-3
DXE-SEI-1
Great for 6 meter Yagi antennas!
The DXE-BEB-3 Insulated Boom-to-Element
Bracket is the convenient, low cost way to mount
elements to smaller (1 inch to 1.75 inch) booms.
The bracket accepts elements up to 3/4 inches.
Use the DXE-SEI-1 Split Element Insulator for 3/4 inch
O.D. aluminum tube used for the driven element.
The insulator allows the element to be securely
clamped without crushing the tube.
DXE-BEB-3
Insulated Boom-to-Element Bracket,
1" to 1.75" Boom ...............$4.49
DXE-SEI-1
Split Element Insulator .....$6.49
DXE-BEB-3
Boom Support Systems
As antennas become larger, booms become
longer, or the wind speed becomes higher, our
3 inch Boom Support Systems will keep the
boom straight. Your antenna will look better,
perform better, and survive storms in better
shape. Many of the individual pieces in these
systems are available separately so you can
design and build your own support systems.
2 Inch Boom Support Components
DXE-ATBB-2
2" Boom Bracket.................$10.75
DXE-TCS-1
Truss Bracket ......................$23.50
3 Inch Dual Boom Support System and Components
DXE-ATBB-3
3" Boom Bracket.................$12.75
DXE-TCS-1
Truss Bracket ......................$23.50
Turnbuckles
DXE-TRBK-14
Turnbuckle, 5.25" Retracted, 7.375" Extended ..................... $6.45
DXE-TRBK-15
Turnbuckle, 6.5" Retracted, 9.125" Extended ....................... $8.85
Orders by 10 pm ET Ship Same Day, See 58 for Details
Antennas: Hardware
49
Yagi Mechanical®
Antenna Design Software
ROH-WM12S
ROH-WM12S
ROH-WM18S
Wall Mounts
Take advantage of rigid walls, use a Rohn Wall
Mount to install your antenna. These mounts include
all the clamps and hardware you need, just add your mast
and you’re ready to go. They handle .875"-2.75" O.D. tubing
and hold the mast away from your wall. They’re hot-dip galvanized to resist corrosion.
Part Number
Description
ROH-WM4
ROH-WM12S
ROH-WM18S
Double Bracket Wall Mount
Extended Wall Mount
Extended Wall Mount
Double Bracket Extended
Wall Mount
ROH-WM18D
Wall
Clearance
Brackets
Included
3"
12"
18"
2
1
1
$28.95
$30.95
$33.95
18"
2
$53.95
Price
Yagi Mechanical® is a tool for anyone who
designs their own antennas or is interested
in modeling an antenna they already own.
Electrical design is first and foremost in crafting a
useful antenna, but the mechanical side of things is
also critical. After all, what good is a great performing
antenna if the wind is going to break the elements
when you put it up on a tower?
DX Engineering’s Yagi Mechanical Antenna Design
Software enables you to analyze your designs and
instantly see where a failure could occur. Whether you
use it to find weak points in old designs or to start brand
new designs with robust mechanical properties, Yagi
Mechanical will provide you with the tools you need to test your
elements for wind and ice, to balance weight and torque on the boom,
and determine if the materials you have selected are up to the task.
Call it good planning for the kind of stress your antennas are going to see. Call it smart
design to prevent regular failures and repairs. Call it peace-of-mind at an affordable
price. We call it Yagi Mechanical!
Yagi Mechanical is a Windows® program, so the graphic user interface should be
very familiar.
DXE-SOF-YAGIMECH Yagi Mechanical® Antenna Design Software w/Key .........$39.95
DXE-SOF-YMKEY
Yagi Mechanical® Key Code Only ......................................$39.95
DXE-SOF-YMDISC
Yagi Mechanical® Backup CD Only ....................................$20.95
Hairpin-Style Driven
Element Matching Kits
Most Yagi antennas have a feedpoint
impedance of about 25 Ω. Obviously,
this will not allow a connection to a 50 Ω
feedline without a serious mismatch.
There are various ways to match the
DXE-HMS-1P
driven element to the feedline successfully.
Gamma, T-Match, and the Hairpin (aka
Beta Match) are favorites.
The Gamma match is an unbalanced
system that typically distorts the antenna
pattern. The T-Match is basically two
Gamma match systems on either side of
the boom, which corrects the imbalance
but is a mechanical nightmare and difficult
to tune correctly.
The DX Engineering Hairpin is balanced and easy to tune. It has the correct electrical
and mechanical design to allow it to be easily installed and tuned in 10 minutes, and has
enough capacity for almost any Yagi design.
For use with BEB-2 Insulated Boom-to-Element Brackets
DXE-HMS-1P
2" Boom ................................................................................. $39.95
For use with BEB-3 Insulated Boom-to-Element Brackets and an SEI Split Element Insert
DXE-HMS-2P
1" to 1.75" Boom ................................................................... $39.95
For use with BEB-1 Insulated Boom-to-Element Brackets
DXE-HMS-4P
3" Boom ................................................................................. $39.95
Boom Mounting Plates
Create and analyze mechanical design parameters.
Create and edit material details and costs.
If you are interested in Yagi
Mechanical, you can download
a trial version FREE! The save,
print, and update functions
are disabled, but the rest of
the program is fully functional,
allowing you to try everything
before you buy.
DXE-BMP-3C
Use these plates to build, mount or repair your Yagi
antenna. These quarter inch-thick aluminum plates are
super-strong to prevent twisting and distortion. They
also represent an excellent way to mount your boom to
the side of your mast or tower. The DXE-BMP-2B plate is
pre-drilled to accept DX Engineering’s Saddle Clamps.
We can help you select the appropriate clamp for your
application, visit online or call us.
DXE-BMP-1C
Plate for 2"-3" Mast, Undrilled, 30" W x 18" L ..................... $78.50
DXE-BMP-3C
Plate for 2"-3" Mast, Undrilled, 24" W x 18" L ..................... $58.50
DXE-BMP-2B
Plate for 1.5"-3" Mast, Pre-Drilled, 8" W x 10" L.................. $34.75
School’s In Session. Unless you’re a teenager, you don,t know everything. This is
especially true in Ham radio. Technology is always marching forward and you have to
keep up. At DXEngineering.com there’s a huge tech library with articles, FAQs, manuals
and videos. Plus, if you’re dealing with a specific issue, call us and we can help.
FREE trial version
at DXEngineering.com
Black Vinyl Caps
These black vinyl caps are designed to fit over the
end of tubing or pipe to keep moisture out. Open vertical tubing
serves as a collection point for rain water. By keeping water out
of the tube end, you reduce corrosion and prevent any collected water from
bursting the tubing when it freezes. They are also perfect for sealing off booms
and Yagi antenna elements. Made from a strong UV-rated material, our caps will
withstand the abuse of nature and keep your installation safe and looking good for years.
Range from 1/8" O.D. Tube to 3" O.D. Tube, visit DXEngineering.com for complete line.
International Shipping is Quick and Easy! See Page 58 for Details
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising