SEGA Golden Gun Manual

MANUAL
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
To maintain safety:
To ensure the safe operation of this product, be sure to read the following before usage.
The following instructions are intended for the users, operators and the personnel in charge of the
operation of the product. After carefully reading and sufficiently understanding the warning displays
and cautions, handle the product appropriately. Be sure to keep this manual close to the product or
in a convenient place for future reference.
Herein, explanations which require special attention are enclosed with dual lines. Depending on
the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. are used.
Be sure to understand the contents of the displays before reading the text.
Indicates that mishandling the product by disregarding this pictograph will
cause severe injury or death.
Indicates that mishandling the product by disregarding this warning will cause
a potentially hazardous situation which can result in death or serious injury.
Indicates that mishandling the product by disregarding this caution will cause
a slight hazardous situation which can result in personal injury and/or material
damage.
For the safe usage of the product, the following pictographs are used:
Indicates "HANDLE WITH CARE." In order to protect the human body and equipment,
this display is attached to places where the instruction manual should be referred to.
Indicates a "protective earth terminal." Before operating the equipment, be sure to connect
it to the ground.
(The step may be omitted for products in which a power cable with earth is used.)
• Perform work in accordance with the instructions herein stated.
Instructions for work are explained by paying attention to the aspect of accident prevention.
Failing to perform work as per the instructions can cause accidents. In the case where only
those who have technical expertise should perform the work to avoid hazardous situation, the
instructions herein state that the site maintenance personnel should perform such work.
• Be sure to turn off the power before working on the machine.
To prevent an electric shock, be sure to turn off the power and unplug the power cable before
carrying out any work that requires direct contact with the interior of the product. If the work is
to be performed in the power-on status, the instruction manual herein always states to that effect.
• Be sure to ground the earth terminal.
(This is not required in the case where a power cable with earth is used.)
This product is equipped with the earth terminal. When installing the product, connect the earth
terminal to the "accurately grounded indoor earth terminal" by using an earth wire. Unless the
product is grounded appropriately, the user can be subject to an electric shock. After performing
repair, etc. for the control equipment, ensure that the earth wire is firmly connected to the control
equipment.
• Ensure that the power supply used is equipped with an earth leakage breaker.
Using a power supply which is not equipped with the earth leakage breaker can cause a fire when
earth leakage occurs.
• Be sure to use fuses which meet the specified rating.
(Only for the machines which use fuses.)
Using fuses exceeding the specified rating can cause a fire and an electric shock.
• Specification changes (removal of equipment, conversion and addition) not
designated by SEGA are not allowed.
The parts of the product include warning labels for safety, covers for personal protection, etc. It
is very hazardous to operate the product by removing parts and/or modifying the circuits. Should
doors, lids and protective parts be damaged or lost, refrain from operating the product, and
contact where the product was purchased from or the office herein stated.
SEGA shall not be held responsible for any accidents, compensation for damage to a third party,
resulting from the specifications not designated by SEGA.
• Ensure that the product meets the requirements of appropriate electrical
specifications.
Before installing the product, check for electrical specifications. SEGA products have a
nameplate on which electrical specifications are described. Ensure that the product is compatible
with the power supply voltage and frequency requirements of the location. Using any electrical
specifications different from the designated specifications can cause a fire and an electric shock.
• Install and operate the product in places where appropriate lighting is available,
allowing warning labels to be clearly read.
To ensure safety for the customers, labels and printed instructions describing potentially
hazardous situations are applied to places where accidents can be caused. Ensure that where the
product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled
off, apply it again immediately. Please place an order with where the product was purchased from
or the office herein stated.
• When handling the monitor, be very careful.
(Applies only to products with monitors.)
Some of the monitor parts are subject to high tension voltage. Even after turning off the power,
some portions are still subject to high tension voltage sometimes. Monitor repair and replacement
should be performed only by those technical personnel who have knowledge of electricity and
technical expertise.
• Be sure to adjust the monitor properly.
(Applies only to products with monitors.)
Do not operate the product leaving on-screen flickering or blurring as it is. Using the product
with the monitor not properly adjusted may cause dizziness or a headache to an operator, a
player, or the customers.
• When transporting or reselling this product, be sure to attach this manual to the
product.
* In the case where commercially available monitors and printers are used in this product, only the
contents relating to this product are explained herein. Some commercially available equipment
has functions and reactions not stated in this manual. Read this manual together with the specific
instruction manual of such equipment.
* Descriptions herein contained may be subject to improvement changes without notice.
* The contents described herein are fully prepared with due care. However, should any question
arise or errors be found, please contact SEGA.
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately
after transporting to the location. Nevertheless, an irregular situation may occur during
transportation. Before turning on the power, check the following points to ensure that the product
has been transported in a satisfactory status.
Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?
Are casters and adjusters damaged?
Do the power supply voltage and frequency requirements meet with those of the location?
Are all wiring connectors correctly and securely connected? Unless connected in the correct way,
connector connections can not be made accurately. Do not insert connectors forcibly.
Do power cables have cuts and dents?
Are all accessories available?
Can all doors and lids be opened with the accessory keys? Can doors and lids be firmly closed?
TABLE OF CONTENTS
i
T ABLE OF CONTENTS
1
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
TABLE OF CONTENTS
INTRODUCTION
i
iv
Definition of 'Site Maintenance Personnel or
Other Qualified Individuals'...................................................................v
1
2
HANDLING PRECAUTIONS
PRECAUTIONS REGARDING INSTALLATION LOCATION
2-1
2-2
3
3-1
3-2
3
4
5
1
3
LIMITATIONS OF USAGE........................................................ 3
OPERATION AREA.................................................................. 4
PRECAUTIONS REGARDING PRODUCT OPERATION
2
6
7
8
9
5
BEFORE OPERATION............................................................. 5
PAYING ATTENTION TO CUSTOMERS................................. 7
10
11
12
13
4
14
5
ACCESSORIES
6
ASSEMBLY AND INSTALLATION
6-1
6-2
6-3
6-4
ATTACHING THE BILLBOARD.............................................. 13
INSTALLING THE CABINET.................................................. 14
CONNECTING THE POWER CABLE AND EARTH.............. 15
ASSEMBLING CHECK........................................................... 17
7
PRECAUTIONS WHEN MOVING THE MACHINE............ 22
9
11
15
16
17
18
19
20
21
22
23
24
E0-1011
420-7318-01
ii
TABLE OF CONTENTS
8
1
8-1
8-2
2
3
4
GAME DESCRIPTION
9
23
HOW TO PLAY....................................................................... 23
SPECIAL FEATURES............................................................ 28
SWITCH UNIT AND COIN METER
31
10 SYSTEM TEST MODE
33
11 GAME TEST MODE
34
5
6
7
8
9
10
11
12
13
14
15
16
17
11-1
11-2
11-3
11-4
11-5
11-6
11-7
11-8
GAME TEST MENU............................................................... 34
BOOKKEEPING..................................................................... 35
INPUT TEST........................................................................... 37
OUTPUT TEST....................................................................... 38
GAME ASSIGNMENTS.......................................................... 39
OPTION ASSIGNMENTS....................................................... 40
CONTROLLER CALIBRATION SETTING.............................. 41
BACKUP DATA CLEAR......................................................... 44
12 CONTROL PANEL
45
12-1 REMOVING THE CONTROL PANEL..................................... 45
12-2 REPLACING THE START BUTTON...................................... 46
13 LCD UNIT
48
13-1 CLEANING THE SCREEN..................................................... 49
18
19
20
21
22
23
24
14 CONTROL UNIT
14-1
14-2
14-3
14-4
50
REMOVING THE CONTROL UNIT........................................ 52
REPLACING THE MICROSWICH.......................................... 54
REPLACING THE SENSOR UNIT......................................... 55
REPLACING THE SOLENOID............................................... 56
15 COIN SELECTOR
15-1 CLEANING THE COIN SELECTOR....................................... 58
15-2 REMOVING THE JAMMED COIN.......................................... 59
15-3 COIN INSERTION TEST........................................................ 59
58
TABLE OF CONTENTS
16 FLUORESCENT LAMP REPLACEMENT
iii
60
1
16-1 BILLBOARD............................................................................ 61
2
17 REPLACING THE FUSE
62
18 PERIODIC INSPECTION
64
3
4
5
19 TROUBLESHOOTING
66
19-1 TROUBLESHOOTING TABLE............................................... 67
19-2 REPLACING THE LED BOARD............................................. 68
6
7
8
20 RINGWIDE
71
20-1 REMOVING THE RINGWIDE................................................. 72
20-2 CLEANING THE RINGWIDE.................................................. 73
20-3 COMPOSITION OF THE RINGWIDEL................................... 74
21 DESIGN RELATED PARTS 9
10
11
75
12
13
22 PARTS LIST
76
23 WIRE COLOR CODE TABLE
83
14
15
16
24 WIRING DIAGRAM
SEGA AMUSEMENTS OFFICES
84
17
18
19
20
21
22
23
24
iv
INTRODUCTION
INTRODUCTION
This manual is intended to provide detailed descriptions together with all the necessary information covering the
general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product,
"SEGA GOLDEN GUN."
This manual is intended for the owners, personnel and managers in charge of operation of the product.
Operate the product after carefully reading and sufficiently understanding the instructions.
In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician
to touch the internal system. Turn off the power to the machine, making sure to unplug the electrical cord from the
outlet, and contact the office listed below or the point of purchase for this product.
Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special
attention are indicated by bold text, the word "IMPORTANT" and the symbol below.
Indicates important information that, if ignored, may result in the mishandling of
the product and cause faulty operation or damage to the product.
SPECIFICATIONS
Instralltion space
46 inches [Width] × 62 inches [Depth]
Height
90 inches
Weight
430 lbs
Power, maximum current
550 W, 4.6A (AC 120 V 60 Hz Area)
INTRODUCTION
Definition of 'Site Maintenance Personnel or Other Qualified Individuals'
Procedures not described in this manual or marked as 'to be carried out by site
maintenance personnel or other qualified professionals' should not be carried
out by personnel without the necessary skill or technology. Work carried out by
unqualified persons may cause serious accidents, including electrocution.
Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel
or other qualified professionals. This manual includes directions for potentially dangerous procedures which should
only be carried out by professionals with the appropriate specialized knowledge.
The site maintenance personnel or other qualified professionals mentioned in this manual are defined as follows:
Site maintenance personnel:
Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the
supervision of the owner/operator of this product to maintain machines within amusement facilities or similar
premises by carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/
expendable parts.
Activities to be carried out by site maintenance personnel:
Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable
parts.
Other qualified professionals:
Persons employed by amusement equipment manufacturers, or involved in design, production, testing or
maintenance of amusement equipment. The individual should have either graduated from technical school or hold
similar qualifications in electrical/electronics/mechanical engineering.
Activities to be carried out by other qualified professionals:
Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.
Game Version Notation
Version numbers appearing in TEST MODE are displayed as asterisks. When describing software version upgrades,
only major version numbers are displayed. Minor version and release version numbers are for Sega’s administrative
use only. If you require these numbers, please contact the office listed in this document.
(Ver)
VER.**.**.**
Major version
(may be only one digit)
Minor version
Release version
v
HANDLING PRECAUTIONS
1
1 HANDLING PRECAUTIONS
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that
the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the cautionary matters
herein stated can cause personal injury or damage to the machine.
● Before performing work, be sure to turn the power off. Performing the work
without turning the power off can cause an electric shock or short circuit. In the
case work should be performed in the status of power on, this manual always
states to that effect.
● To avoid an electric shock or short circuit, do not plug in or unplug quickly.
● To avoid an electric shock, do not plug in or unplug with a wet hand.
● Do not expose power cable or earth wires on the surface, (floor, passage, etc.). If
exposed, the power cable and earth wires are susceptible to damage. Damaged
cords and wires can cause an electric shock or short circuit.
● To avoid causing a fire or an electric shock, do not put things on or damage the
power cable.
● When or after installing the product, do not unnecessarily pull the power cable.
If damaged, the power cable can cause a fire or an electric shock.
● In case the power cable is damaged, ask for a replacement through where the
product was purchased from or the office herein stated. Using the cord as is
damaged can cause fire, an electric shock or leakage.
● Be sure to perform grounding appropriately. Inappropriate grounding can cause
an electric shock.
● Be sure that connections such as IC board are made properly. Insufficient
insertion can cause an electric shock.
● Specification changes, removal of equipment, conversion and/or addition, not
designated by SEGA are not permitted.
- Failure to observe this may cause a fire or an electric shock. Non-compliance
with this instruction can have a bad influence upon physical conditions of the
players or the onlookers, or result in injury during play.
- SEGA shall not be held responsible for damage, compensation for damage to a
third party, caused by specification changes not designated by SEGA.
● Do not perform any work or change parts not listed in this manual. Doing so may
lead to an accident.
● If you need to perform any work not listed in this manual, request work from the
office indicated in this manual or the point of purchase, or inquires for details.
● Be sure to perform periodic maintenance inspections herein stated.
1
2
HANDLING PRECAUTIONS
1
●For the IC board circuit inspections, only the logic tester is allowed. The use of a
multiple-purpose tester is not permitted, so be careful in this regard.
●Static electricity from your body may damage some electronics devices on the IC
board. Before handling the IC board, touch a grounded metallic surface so that
the static electricity can be discharged.
●This product uses a DLP projector. DLP projector screens scratch easily, so
be careful when cleaning the screen. See Chapter 13 "DLP PROJECTORS" for
details.
●Some parts are not designed and manufactured specifically for this game
machine. The manufacturers may discontinue, or change the specifications of
such general-purpose parts. If this is the case, SEGA cannot repair or replace a
failed game machine whether or not a warranty period has expired.
●Do not turn the power on and off continuously. Repeatedly turning the power on
and off may cause product malfunction or parts damage.
CONCERNING THE SERIAL NO. AND THE ELECTRICAL SPECIFICATIONS DISPLAYS
This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical
Specifications. It also has a Sticker describing where to contact for repair and for purchasing parts.
When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker.
The Serial Number indicates the product register. Identical machines could have different parts depending on the
date of production. Also, improvements and modifications might have been made after the publication of this
manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places.
CONCERNING WARNING DISPLAYS
This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or
incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended
for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing
work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing
maintenance, be very careful of the warning displays. It is especially important that any complex repair and
replacement work not mentioned herein should be performed by those technical personnel who have knowledge of
electricity and technical expertise.
In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately.
PRECAUTIONS REGARDING INSTALLATION LOCATION
3
2 PRECAUTIONS REGARDING INSTALLATION LOCATION
2
This product is an indoor game machine. Do not install it outside. Even indoors,
avoid installing in places mentioned below so as not to cause a fire, electric
shock, injury and/or malfunction.
- Places subject to rain or water leakage, or places subject to high humidity in the
proximity of an indoor swimming pool and/or shower, etc.
- Places subject to direct sunlight, or places subject to high temperatures in the
proximity of heating units, etc.
- Places filled with inflammable gas or vicinity of highly inflammable/volatile
chemicals or hazardous matter.
- Dusty places.
- Sloped or unstable surfaces.
- Places subject to any type of violent impact.
- Vicinity of anti-disaster facilities such as fire exits and fire extinguishers.
- Areas where the temperature exceeds the applicable temperature (ambient
temperature) range of 5 to 30 degrees centigrade.
2-1 LIMITATIONS OF USAGE
● Be sure to check the Electrical Specifications. Ensure that this product
is compatible with the location's power supply, voltage, and frequency
requirements. A plate describing Electrical Specifications is attached to the
product. Non-compliance with the Electrical Specifications can cause a fire and
electric shock.
● This product requires a breaker and earth mechanism as part of the location
facilities. Using the product without these can cause a fire and electric shock.
● Be sure to use an independent power supply equipped with an earth leakage
breaker. Using a power supply without an earth leakage breaker can cause an
outbreak of fire if a power surge occurs.
● Putting many loads on one electrical outlet can cause generation of heat and a
fire resulting from overload.
● Ensure that the indoor wiring for the power supply is rated at 15 A or higher (AC
single phase 100 V ~ 120 V area), and 7 A or higher (AC 220 V ~ 240 V area). Noncompliance with the Electrical Specifications can cause a fire and electric shock.
● When using an extension cord, ensure that the cord is rated at 15 A or higher (AC
100 V ~ 120 V area) and 7 A or higher (AC 220 V ~ 240 V area). Using a cord rated
lower than the specified rating can cause a fire and electric shock.
4
PRECAUTIONS REGARDING INSTALLATION LOCATION
Electricity Consumption
MAX. 4.6 A
Single phase AC 120 V, 60 Hz Area
2
2-2 OPERATION AREA
● For safe operation, use and operate this product in an area measuring at least
2.1 m (82.7 in) in width and 2.8 m (110.2 in) in depth. The area prescribed in this
manual is absolutely necessary, for if one should fall over and hit their head
against something, there could be a serious accident.
● Be sure to provide sufficient space specified in this manual. Do not allow objects
to block the ventilation ports. It can cause generation of heat and a fire.
● SEGA shall not be held responsible for damage or compensation for damage to
a third party, resulting from the failure to observe this instruction.
● The ceiling where this product is installed must be at least 2.4 m (94.5 in) high. If
the ceiling is too low, the heat emitted from the product may cause it to catch on
fire.
0.2 m
(7.9 in)
2.1m (82.7 in)
2.8 m (110.2 in)
0.25m
(9.8 in)
0.6m (23.6 in)
0.25m
(9.8 in)
PRECAUTIONS REGARDING PRODUCT OPERATION
5
3 PRECAUTIONS REGARDING PRODUCT OPERATION
To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.
3-1 BEFORE OPERATION
In order to avoid accidents, check the following before starting the operation:
● To ensure maximum safety for the players and the customers, ensure that where
the product is operated has sufficient lighting to allow any warnings to be read.
Operation under insufficient lighting can cause bodily contact with each other,
hitting accident, and/or trouble between customers.
● Be sure to perform appropriate adjustment of the monitor. For operation of this
product, do not leave monitor's flickering or deviation as is. Failure to observe
this can have a bad influence upon the players' or the customers' physical
conditions.
● It is suggested to ensure a space allowing the
players who feel sick while playing the game
to take a rest.
● Check if all of the adjusters are in contact
with the surface. If they are not, the cabinet
can move and cause an accident.
Ensure that all of the adjusters
are in contact with the floor.
● Do not put any heavy item on this product. Placing any heavy item on the
product can cause a falling down accident or parts damage.
● Do not climb on the product. Climbing on the product can cause falling down
accidents. To check the top portion of the product, use a stepstool.
● To avoid electric shock, check to see if door and cover parts are damaged or
omitted.
● Do not place the following items on top of the product, nearby the product or
hang them from the ceiling. Doing so could result in electric shock, short circuits
and/or damage to the parts.
Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/
containers/vessels containing chemicals and water.
3
6
PRECAUTIONS REGARDING PRODUCT OPERATION
● To avoid injury, be sure to provide sufficient space by considering the potentially
crowded situation at the installation location. Insufficient installation space can
cause contact, collisions, and/or trouble between customers.
3
● During daily cleaning, be sure to check the surface of the parts that the player
touches with his/her hands for damage, cracks, or loose screws. If a player uses
the machine while it is damaged, cracked, or has a loose screw, the player may
become injured.
● Be sure to check carefully that there are no gaps or rattling at the door or/and
the junction of the cabinet. If there are gaps or rattling, the players could get
fingers or hands caught, resulting in injury.
● Make sure all the doors are locked securely and that they do not rattle. If the
doors are not locked properly or there are gaps or rattling, the players could get
their fingers or hands caught. It could also invite mischief.
● Be sure to perform appropriate adjustment of DLP projector. For operation
of this machine, do not leave monitor's flickering or deviation as is. Failure
to observe this can have a bad influence upon the players' or the customers'
physical conditions.
● Prepare a place where players can rest if they feel sick.
●Players directly hold the controller with their bare hands so it is recommended
that wet towels (paper towels) be provided.
●Placing the DLP projector near halogen lamps or other types of light fixtures
which emit strong light may cause a malfunction. Make sure to install the
projector at a reasonable distance from such sources of light.
PRECAUTIONS REGARDING PRODUCT OPERATION
7
3-2 PAYING ATTENTION TO CUSTOMERS
To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.
● For safety reasons, do not allow any of the following people to play the game.
Failure to observe this warning could result in serious injury.
- Those who need assistance such as the use of apparatus when walking.
- Those who are intoxicated or under the influence of drugs.
- Persons who disregard the product's warning displays.
● Instruct those who feel sick during play to have a medical examination.
● To avoid injury from falls and electric shocks due to spilled drinks, instruct the
player not to place heavy items or drinks on the product.
● To avoid electric shocks and short circuits, do not allow customers to put
hands and fingers or extraneous matter in the openings of the product or small
openings in or around the doors.
● To avoid falls and resulting injury, immediately stop the customer from leaning
against or climbing on the product, etc.
● To avoid electric shock and short circuit, do not allow customers to unplug the
power plug without a justifiable reason.
● For safety reasons, do not allow any of the following people to play the game.
Failure to observe this caution could result in an accident or injury.
- Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
- Those who are not in good health.
- Pregnant women.
- Persons susceptible to motion sickness.
- Those who have high blood pressure or a heart problem.
- Those who have neck or spinal cord problems.
● Even players who have never been adversely affected by light stimulus might
experience dizziness or headache depending on their physical condition when
playing the game. Small children are especially likely to experience these
symptoms. Caution guardians of small children to keep watch on their children
during play.
● Immediately stop such violent acts as hitting and kicking the product. Such
violent acts can cause parts damage or falling down, resulting in injury due to
fragments and falling down.
● Persons other than the player should not be allowed to touch the controls during
play. They may brush against or collide with the controls or the player, possibly
resulting in accidents.
3
8
3
PRECAUTIONS REGARDING PRODUCT OPERATION
● Be sure to instruct the adult responsible for their children to watch them.
Children cannot sense danger. Approaching the player during play may result
in accidental contact, collisions or falls. If the control unit is pulled from the
controller holder and dropped on the head, it may cause injury.
● Caution the player not to wrap the control unit cable around his/her wrist or
neck, as this can lead to serious injury.
● Immediately stop users from leaning or sitting on the controller panel. Such acts
can lead to injury or damage to parts or the shape of the cabinet.
● Immediately stop users from swinging or reloading the control unit in a violent
manner. Such acts may hurt the user or other people around them.
● Playing too close to the cabinet may cause the control unit to hit the cabinet
and cause damage. Make sure that players understand to play at a safe distance
from the cabinet.
● Make sure that players understand not to stand too close together when playing
a 2 player game. Swinging the control unit could lead to a player getting hit and
may cause injury.
● Instruct players to hold the control unit securely while playing. If the Control
Unit is dropped, it could cause injury to the player.
● Items such as large finger rings can cause injury to the fingers while playing.
Instruct players to remove all accessories that could cause an accident before
playing.
● Instruct players that a single control unit is never to be held by 2 or more people
during play. Otherwise there could be dangerous contact or a collision.
The control units for use on 1P side (left side) and 2P side (right side) are different.
Ensure that players do not confuse the right and left side Control Units when
starting play.
ACCESSORIES
9
4 ACCESSORIES
Confirm that the accessories listed in the table below are present when setting up the product.
Accessories marked Spare in the note column are consumable items but included as spares.
Parts not labeled with part numbers are as yet unregistered or cannot be registered. Be sure to handle all parts with
care, as some parts are not available for purchase separately.
Part name/Part no.
Diagram/Use etc.
Quantity
5
OWNER’S MANUAL
574-30-300
1
This manual
KEY
2
POWER CABLE
DVD SOFTWARE KIT
1
When you order the DVD only, specify the part number DVR-0026
RGW DVDROM GLG
10
ACCESSORIES
The DVD drive is sold separately, but it is required in order to install the software for this product. If you do not
have the drive when installing the product, consult the dealer from which you purchased this product. Alternatively,
use the kit number below to arrange for a drive.
XKT-1515-01:DVD DRIVE KIT FOR LBG ENG
5
Part name/Part no.
Diagram/Use etc.
DVD DRIVE SERVICE MANUAL
420-6923-01
Quantity
1
DVD DRIVE
610-0719-03
1
For software installation
DVD WIRE
605-0094
2
For software installation
ASSEMBLY AND INSTALLATION
11
6 ASSEMBLY AND INSTALLATION
● Perform assembly work by following the procedure herein stated. If instructions
are not followed, or if tasks and/or checks are neglected, an electric shock or
other very serious accident, even fatal accident, can occur. Also, customers
could be injured while operating the product.
● Be careful not to damage the wires. Damaged wires may cause electric shock or
short circuit or present a risk of fire.
● Provide sufficient space so that assembling can be performed. Performing work
in places with narrow space or low ceiling may cause an accident and assembly
work to be difficult.
● To perform work safely and avoid serious accident such as the cabinet falling
down, do not perform work in places where step-like grade differences, a ditch,
or slope exist.
● When assembling, more than one person is required. Depending on the
assembly work, there are some cases in which working by one person alone can
cause personal injury or parts damage.
● Ensure that connectors are properly connected. Improper connections can
cause electric shock.
● This work should be carried out by the site maintenance personnel or other
qualified professionals. Work performed by non-technical personnel can cause
a severe accident such as electric shock. Failing to comply with this instruction
can cause a severe accident such as electric shock to the player during
operation. If no one with proper technological expertise is available, request
service from the office indicated in this document or the point-of-purchase so as
to ensure safety.
● Do not leave power cable, earth wires, or network cables exposed in areas of
heavy foot traffic. Doing so may cause them to become damaged, possibly
resulting in electric shock and/or short circuits. When laying wiring across the
floor, always use safety covers to protect the wires. (Wiring diameter: power
cable, approx. 8 mm)
● Be careful in handling plastic parts. Be sure not to tighten screws or nuts too
tightly. If such parts are exposed to excessive loads or impact, they might
become damaged, resulting in fragments or cracks that could cause accidental
injury.
● When attaching or removing doors or parts, be careful that your hand or finger
does not get caught in anything.
● Wear appropriate work clothing so that work can be performed safely. Use
gloves and safety shoes to prevent accidents or injuries.
● To perform work safely and securely, be sure to prepare a step which is in a
secure and stable condition. Performing work without using the step can cause
accidents such as falling down.
6
12
ASSEMBLY AND INSTALLATION
Be very careful when handling the DLP projector screen. The screen is easily
damaged but cannot be repaired. If damaged the entire screen must be replaced.
TOOLS NECESSARY FOR WORK
6
Phillips screwdriver Spanner with variable measuring distance
Socets for hexagon bolts and nuts
Master key
Stepstool
ASSEMBLY AND INSTALLATION
13
6-1 ATTACHING THE BILLBOARD
Use several steps to perform the assembly work on the top of the machine.
1
Lift the 574-50-111 marquee front cover with at least 2 people and set it on top of the LCD from the back.
Unscrew 4 screws on marquee bracket, and insert between back marquee bracket.
6
2
Lift the 574-30-211 rear marquee with at least 2 people and set it on top of the LCD from the back.
Unscrew 4 screws on marquee bracket, and insert between back marquee bracket.
14
ASSEMBLY AND INSTALLATION
6-2 INSTALLING THE CABINET
Be sure to ground the adjusters, and secure the product firmly to the installation
location. If the projector moves either during assembly work or during operation
after the completion of assembly, a serious accident may occur.
6
This product has 4 casters and 4 adjusters. After determining the installation location, have the adjusters contact the
floor directly, and adjust them so the machine will remain in a level position keeping a space of about 5 mm between
the floor and the casters.
1
2
3
Move the product to the installation site. Hold the grips on the sides of the cabinet when moving it and
changing the direction it faces. Secure a 200 mm space between the back wall and the back of the cabinet
for ventilation.
Use a wrench to set adjuster heights so that the unit will stay level.
After setting, turn adjuster nuts upwards to tighten them and secure adjuster heights.
ASSEMBLY AND INSTALLATION
15
6-3 CONNECTING THE POWER CABLE AND EARTH
● Use the power supply equipped with an earth leakage breaker. Use of power
supply without such a breaker could result in fire if there is a current leakage.
● Have available a securely grounded indoor earth terminal. This product is
equipped with a earth terminal. Connect it to a earth terminal in the room with
the earth wire. Without proper grounding, customers could be electrocuted and
product operations might not always be stable.
● Do not expose the power cable or earth wire. If these are exposed, customers
could stumble over them, for instance, and easily damage them. Additionally, if
these lines are damaged, there could be a risk of electrical shock or short circuit.
Set these lines at locations where they will not interfere with customer traffic, or
attach covers to them.
● After laying out the power cable on the floor, be sure to always protect it. If the
power cable is left exposed, it can easily be damaged, resulting in electrical
shock.
● For safety reasons, be sure to first connect the power cable to the product. If the
power cable is first connected to the power plug, an accident such as an electric
shock or short circuit may occur.
If grounding has been established with the earth wire inside the power cable, do not
perform grounding with the AC unit earth terminal. Conversely, if the AC unit earth
terminal has been used for grounding, do not establish ground with the earth wire in
the power cable. Otherwise there could be faulty or erroneous operations.
6
16
ASSEMBLY AND INSTALLATION
The AC unit has main switch, circuit protector and the inlet which connects the power cable.
1
6
Confirm that the AC unit power switch is at OFF.
Main switch OFF.
2
3
Connect one end of the earth wire to the AC earth terminal, and the other end to the indoor earth terminal.
The accessory power cable contains earth wire. Connect power cable to AC unit inlet, and then insert
power plug into "power outlet with earth terminal".
When using a conversion adapter sold on the market to provide power, connect the adaptor’s earth wire
terminal to an "earth terminal that is securely grounded".
The power cable is laid out indoors. Protect the power cable by attaching wire cover to it.
ASSEMBLY AND INSTALLATION
17
6-4 ASSEMBLING CHECK
Using TEST MODE, verify points such as the proper assembly of the machine. Also verify normal operation of
the RINGWIDE, boards which have been connected, and the product’s various input and output devices. In TEST
MODE, conduct the tests described below.
(1) MONITOR TEST
When MONITOR TEST is chosen from SYSTEM TEST MENU screen, a screen to test the Monitor will be
displayed.
Though the Monitor is pre-adjusted at the time of shipment from the factory, view the test screen to determine
whether or not adjustment is necessary. If so, refer to Chapter 13-2 "DLP PROJECTOR ADJUSTMENT"and adjust
the Monitor.
MONITOR TEST 1/2
MONITOR TEST 2/2
1
32
PRESS TEST BUTTON TO EXIT
PRESS TEST BUTTON TO NEXT
(2) SPEAKER TEST
When SPEAKER TEST is chosen from SYSTEM TEST MENU screen, a screen to test each of the speakers will be
displayed.
The RIGHT SPEAKER and the LEFT SPEAKER are the only speakers which can be checked by just changing their
respective settings to ON and OFF.
SPEAKER TEST
LEFT SPEAKER
RIGHT SPEAKER
REAR LEFT SPEAKER
REAR RIGHT SPEAKER
CENTER SPEAKER
WOOFER SPEAKER
OFF
OFF
OFF
OFF
OFF
OFF
-> EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
6
18
ASSEMBLY AND INSTALLATION
(3) INPUT TEST
When INPUT TEST is chosen from GAME TEST MENU screen, a screen to test the game’s switches will be
displayed.
Confirm each input device is functioning correctly.
[Normal]
- When the controller is turned towards the screen, the word "OUT" beside "SCREEN IN" will change to "IN."
- If other input devices are operated, the word "OFF" beside the device name will change to "ON."
(See 11-3.)
INPUT TEST
6
CONTROLLER TRIGGER
CONTROLLER X
CONTROLLER Y
SCREEN IN
START
SERVICE
TEST
PLAYER1
OFF
**
**
OUT
OFF
PLAYER2
OFF
**
**
OUT
OFF
OFF
OFF
PRESS TEST BUTTON AND
SERVICE BUTTON TO EXIT
INPUT TEST screen
(4) OUTPUT TEST
When OUTPUT TEST is chosen from GAME TEST MENU screen, a screen to test lamps and their wiring
connections will be displayed.
Confirm each output device is functioning correctly.
[Normal]
- When the TEST Button is pressed, the selected item will change from "OFF" to "ON" and the corresponding
output device will operate. If the TEST Button is pressed for an item that is "ON," the device will change to "OFF"
and stop operating.
(See 11-4)
OUTPUT TEST
START1 LAMP
START2 LAMP
PANEL1 LAMP
PANEL2 LAMP
PLAYER1 CONTROLLER REACTION
PLAYER2 CONTROLLER REACTION
-> EXIT
OFF
OFF
OFF
OFF
OFF
OFF
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
OUTPUT TEST screen
ASSEMBLY AND INSTALLATION
19
(5) CONTROLLER ADJUSTMENT
When CONTROLLER ADJUSTMENT is chosen from CONTROLLER CALIBRATION SETTING under GAME
TEST MENU screen, a screen for adjusting the Control Unit crosshair will be displayed.
Before operating the product, always play the game to verify that there are no irregularities during play and that the
crosshair does not require adjustment.
Though the crosshair is adjusted at the factory, adjustment may be required in some situations because the product is
disassembled for shipment. (See 11-7.)
PLAYER1 CONTROLLER ADJUSTMENT
6
↑PLEASE SHOOT GRID WITH PLAYER1 CONTROLLER
PRESS TEST BUTTON TO EXIT
CONTROLLER ADJUSTMENT screen
NOTE: Strong lighting located near the monitor, other machines in the surrounding area, and other objects may
have an effect on the controller adjustment.
The above inspections (1) – (4) should be conducted regularly as part of a monthly inspection.
However, (5) CONTROLLER ADJUSTMENT should be conducted once per week.
20
ASSEMBLY AND INSTALLATION
THE INTERFERENCE PREVENTION WIRING
● This work should be performed by the site maintenance individual or other
skilled professional. Work performed by non-technical personnel can cause
malfunctioning.
● In order to prevent electric shock and short circuit hazards, be sure to turn the
power off before performing work.
6
● Be careful not to damage the wires. Damaged wires may cause electric shock or
short circuit or present a risk of fire.
When the game machines of a same or similar type are installed side by side, their sensors may interfere with each
other. To reject the interference, follow the procedure below.
The following game machines employ a same or similar type of sensor. If interference happens to the sensors,
operation of the games may be mutually disturbed.
- THE HOUSE OF THE DEAD 2, U/R type, DX type and Super DX type
- DEATH CRIMSON, U/R type and DX type
- THE LOST WORLD, U/R type, DX type and Super DX type
- BRAVE FIRE FIGHTERS
- SAMBA DE AMIGO
- CONFIDENTIAL MISSION, U/R type and DX type
- SHAKATTO TAMBOURINE
- LUPIN THE 3RD THE SHOOTING, U/R type and DX type
- THE MAZE OF THE KINGS, U/R type and DX type
- THE HOUSE OF THE DEAD 3, U/R type and DX type
- VIRTUA COP 3, U/R type and DX type
- GHOST SQUAD, U/R type and DX type
- THE HOUSE OF THE DEAD 4 DX type and SPECIAL type
- 2SPICY
- RAMBO
- Ai Sareru Yori Ai Shitai
- SEGA GOLDEN GUN
1
2
Turn the power off.
Remove the 8 screws, and take back cover off.
ASSEMBLY AND INSTALLATION
3
21
There is an interference prevention wire on the lower level inside the left side front door.
INTERFERENCE PREVENTION WIRE
RMB-60047
6
Enlargement
4
5
Refer to Step 2 and work in reverse order to attach the left front door.
If several of the same type of game machines are to be installed beside each other, they should be lined
up alternating between ones with the interference prevention wire connected and ones that with the wire
removed. Be sure to keep the removed interference prevention wire.
22
PRECAUTIONS WHEN MOVING THE MACHINE
7 PRECAUTIONS WHEN MOVING THE MACHINE
● When moving the machine, be sure to pull out the plug from the power supply.
Moving the machine with the plug still inserted can cause the power cable to be
damaged, resulting in a fire and/or electric shock.
● When moving the machine on the floor, retract the adjusters, and ensure that the
casters make contact with the floor. Pay careful attention so that the casters do
not run over power cable and earth wires. Damaging the power cable can cause
an electric shock and/or short circuit.
7
● When lifting the cabinet, be sure to hold the grips and the bottom part. Lifting the
cabinet by holding other portions may damage parts and installation portions
due to the empty weight of the cabinet, and may cause personal injury.
● When moving the DLP projector, do not push it from the rear side. Push it
from sideways. Pushing the DLP projector from the rear side can have the DLP
projector fall down, causing personal injury, etc. In case the floor has slanted
surfaces or step-like differences, be sure to move the machine by 2 or more
persons.
● Never disassemble the unit in ways other than those described in this manual.
Doing so can cause accidents such as electric shocks, short circuits, and fires.
● Do not hold or press the plastic parts as indicated by the figure. Failure to
observe this instruction may break the parts, and eventually the broken pieces
may cause a personal injury.
● When moving the cabinet, push on the parts made of sheet metal or by holding
the handles. Putting fingers into the coin return or other open slots, or opening
doors and holding the machine by the door frames could damage the edges or
may result with fingers getting shut in the doors.
●If the machine is going to be moved somewhere on a different level, disassemble
it into the individual units before doing so. If the machine is tilted or the cabinet
is set on an uneven surface the joints may break.
●Do not allow ropes to come in contact with the surface of the machine directly or
they may scratch it. Put some kind of protective material under the rope where it
will touch the machine.
●When moving the cabinet, do not hold it by the control unit or pull on the control
unit. Doing so could damage the parts or cause them to become deformed.
GAME DESCRIPTION
23
8 GAME DESCRIPTION
8-1 HOW TO PLAY
1
2
3
When you insert coins, they will be counted in the credit display at the bottom of the screen. When you
insert enough coins for a game, the message at the bottom will change from "INSERT COIN (S)" to
"PRESS START BUTTON," and the start buttons on either side will flash.
Up to 24 credits can be counted at once. Coins inserted after 24 credits are recorded will not be counted or
returned. However, the number of coins inserted will be counted in the data display and the coin meter.
NOTE: The number of credits required for a game can be set in SYSTEM TEST MODE. Refer to 10.
"SYSTEM TEST MODE" for details.
Which START button you press determines which side you play on. Once you press the START button,
the game begins.
Once the game starts, the video demonstration will play, followed by the stage title, and then it will go to
the actual game.
GAME SCREEN
The score, ammo remaining, player mark, and life of the player playing on the left (PLAYER 1) are shown at the
left side of the screen, while those of the player playing on the right (PLAYER 2) are shown at the right side of the
screen. Credits are always displayed at the bottom of screen.
If there is no player, the required number of credits is displayed instead.
ITEM TIME LIMIT
SCORE
AMMO REMAINING
PLAYER MARK
LIFE
GAME screen
CREDITS
CREDITS REQUIRED
RELOADING
When the player fires all ammo remaining, the gun will be empty. The player can then reload the weapon by aiming
it outside the screen. The player can reload this way even if there are still bullets left.
The gun is also reloaded automatically when the trigger is pulled with no ammo remaining. However, this type of
reload takes longer than a normal reload.
8
24
GAME DESCRIPTION
SCORE ITEMS
Various score items appear when the player shoots treasure boxes or "hidden" boxes in the background. Hidden box
appear when the player aims at certain secret areas.
Picking up score items increases the player’s score by various amounts based on the type of item.
Shooting fireworks boxes causes explosions that defeat nearby enemies.
8
Coin (+200)
Silver Ingot (+400)
Gold Ingot (+600)
Sword (+800)
Fan (+1,000)
Ginseng (+2,000)
Drum (+100×max.20)
Imperial Seal (+3,000)
Fireworks Box
GAME DESCRIPTION
25
SHOP ITEMS
In each stage, the player meets an item merchant twice.
The player can purchase various weapons and items from the merchant.
For each stage the player advances, item prices go up by 10%.
In 2-player mode, items cost 70% of the price they are in 1-player mode.
■Weapons (permanent effect)
Attack Power Up (+1) Magazine (+1) 8
■Weapons (limited use)
Machine Gun (+6 sec.)
Shot Gun (+6 sec.)
Piercing Ammo (+1) Missile (+1)
■Items (one-time use)
Enemy Weakener (+1) ■Etc.
Mystery Ball
Fast Reload
Life (+1)
26
GAME DESCRIPTION
EVENTS
Various events occur in the course of the game, such as "Shoot the arch to block enemies," "Battle your secret rival,"
"Shoot down the incoming energy balls," and "Shoot the driver of the car."
A "Shoot" prompt appears on screen, telling the player to shoot the target objects marked with red circles.
8
EVENT screen
If the player succeeds, he/she can get a score bonus (1000 pts.) and sometimes avoid enemy attacks.
If the player fails, he/she will have to battle many enemies or be forced to take damage.
BATTLES WITH BOSSES
A unique boss awaits the player at the end of each stage.
Their weak points are revealed in the form of on-screen prompts.
BOSS BATTLE START screen
WEAK POINT PROMPT
GAME DESCRIPTION
27
BOSS BATTLE SCREEN
Attacking the boss’s weak point drains the boss’s LIFE gauge significantly.
When the boss begins an attack, a cancel gauge will sometimes appear.
As the boss approaches the player, the cancel gauge changes from green to yellow, orange, and finally red according
to the danger level.
The boss’s attack can be avoided by forcing the cancel gauge down to zero.
BOSS'S LIFE GAUGE
BOSS'S CANCEL GAUGE
8
BOSS BATTLE screen
Shooting the boss drains the boss’s LIFE gauge. When the boss’s LIFE gauge reaches zero, the boss is defeated.
GAME OVER
If both players run out of LIFE, the game ends. LIFE is shown as burning fire.
1
2
3
If you want to join the game during play, insert coins and press the START button at any time. If there are
enough credits remaining to play, the START button on the side with no one playing flashes continuously.
Join the game by pressing the flashing START button.
When all LIFE is lost, the CONTINUE message is displayed. If you wish to CONTINUE, insert the
required number of coins and press the START button again. If there are enough credits remaining to
CONTINUE, you can join again by pressing the START button.
NOTE: The number of credits required to continue can be set in SYSTEM TEST MODE. Refer to 10."
SYSTEM TEST MODE" for details.
If your total points rank among the top 10 after completing all the stages in the game, you can enter your
name.
28
GAME DESCRIPTION
8-2 SPECIAL FEATURES
These are special features to encourage users to play the game.
Each feature can be turned ON/OFF and its effects adjusted in TEST MODE.
PREMIUM START CHANCE
Using extra credits to start the game allows players to start in a powered-up state.
Both Players 1 and 2 have only a single chance to do this. The Premium Start Chance feature cannot be used twice
in a row.
CREDIT(S) REQUIRED
TIME LIMIT
8
OK BUTTON
EXIT BUTTON
CREDIT(S) INSERTED
■Controls
- The [OK] button lights up when the number of credits inserted meets the requirement for a Premium Start.
- Shooting the [OK] button when it is lit up causes the game to start powered up at the cost of credits.
- Shooting the [EXIT] button causes the game to start normally.
■Menu Items
ATTACK POWER UP
Can be set from +1 to +10 in TEST MODE (Default setting: +2)
LIFE BONUS
Can be set from +1 to +9 in TEST MODE (Default setting: +1)
MAGAZINE BONUS
Can be set from +1 to +10 in TEST MODE (Default setting: +2)
GAME DESCRIPTION
29
EXCHANGE CHANCE
NOTE: Scores achieved with this feature cannot be entered in the score rankings at the end of the game.
Players can spend credits in items shops to gain extra score, which can then be used to purchase items.
Both Players 1 and 2 have only a single chance to do this. The Exchange Chance feature cannot be used twice in a
row. (It can, however, be used again in a different shop.)
CREDIT(S) REQUIRED
TIME LIMIT
SCORE BONUS
8
OK BUTTON
EXIT BUTTON
CREDIT(S) INSERTED
■Controls
- The [OK] button lights up when the number of credits inserted meets the requirement for an Exchange Chance.
- Shooting the [OK] button when it is lit up causes the game to award a set number of points at the cost of credits,
and then return to the shopping screen.
- Shooting the [EXIT] button causes the player to exit the shop and continue the game.
■Menu Item
SCORE BONUS
Can be set from +10000 to +90000 in increments of 10000 in TEST MODE (Default setting:
+10000)
30
GAME DESCRIPTION
CONTINUE BONUS
NOTE: This feature is not included for REGION EXP (EUROPE).
1
2
3
4
When the Continue screen appears, an item roulette begins spinning.
The player inserts the required number of credits and presses the START button to continue the game.
The player is awarded whichever item was lit up when the START button was pressed.
The game continues.
8
ROULETTE
BONUS ITEM (LIT UP)
SWITCH UNIT AND COIN METER
31
9 SWITCH UNIT AND COIN METER
Do not touch undesignated places. Touching places not designated can cause
electric shock or short circuit.
When opening/closing or attaching or removing the doors or the other parts, be
careful that your hand or finger does not get caught in anything.
9
●When you enter the TEST MODE, fractional coin and bonus adder data is erased.
●Adjust the sound to the optimum volume, taking into consideration the
environmental requirements of the installation location.
●Removing the coin meter circuitry renders the game inoperable.
In TEST MODE, the switch unit in the coin chute door is operated.
Unlock and open the coin chute door. Inside is a switch unit.
SWITCH UNIT
TEST BUTTON
SERVICE BUTTON
SOUND VOLUME SWITCH
TEST Button
(TEST)
Activates TEST MODE. Becomes the button to confirm selections in TEST
MODE.
SERVICE Button
(SERVICE)
Makes it possible to enter credits for service without increasing the coin meter.
Becomes the button to select items in TEST MODE.
SOUND VOLUME Knob
(SOUND VOLUME)
Controls the volume for the speakers to the left and right of the control panel.
Turn the knob to the right to increase speaker volume.
32
SWITCH UNIT AND COIN METER
COIN METER
After using a special-purpose key to unlock the cashbox door, the coin meter can be found at the bottom of the
cashbox.
COIN METER
9
SYSTEM TEST MODE
33
10 SYSTEM TEST MODE
●Go to BOOKKEEPING in GAME TEST MODE to access this product’s data.
●Read the RINGWIDE service manual that comes with the product for details on
the SYSTEM TEST MODE. However, you should perform the settings for this
product according to the manual you are reading.
●The details of changes to TEST MODE settings are saved when you exit from
TEST MODE by selecting EXIT from the SYSTEM TEST MODE menu. Be careful
because if the power is turned off before that point, changes to the settings will
be lost.
●Use with the specified settings. If settings other than those specified are used,
inappropriate operations or malfunction may occur.
In the SYSTEM TEST MODE, the main activities include checking RINGWIDE information and actions and the
setting of coin/credit. Also, a screen appears for checking screen adjustments. For details, refer to the RINGWIDE
service manual, which is provided with the product. Press the TEST Button to enter TEST MODE and bring up the
SYSTEM TEST MENU screen.
Use the following settings with this product. If the settings are not as specified, error messages may appear and the
product may not operate as intended.
COIN ASSIGNMENTS
COIN CHUTE TYPE
COMMON
SERVICE TYPE
COMMON
NETWORK SETTING
DHCP
ENABLE
The GAME COST SETTING screen in COIN ASSIGNMENTS appears as follows:
COIN ASSIGNMENTS
GAME COST SETTING
*credit
*credit
*credit
*credit
->
(s)
(s)
(s)
(s)
to
to
to
to
start
continue
premium start
exchange
EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
■Menu Items
* credit (s) to start
Sets the number of credits required to start the game.
* credit (s) to continue
Sets the number of credits required to continue.
* credit (s) to premium start
Sets the number of credits required for Premium Start.
* credit (s) to exchange
Sets the number of credits required for Exchange Chance.
10
34
GAME TEST MODE
11 GAME TEST MODE
●To change settings in the GAME TEST MODE, simply making changes on the
setting screen will not be effective. Complete the TEST MODE in normal fashion.
●Use with the specified settings. If settings other than those specified are used,
inappropriate operations or malfunction may occur.
11-1 GAME TEST MENU
Select GAME TEST MENU from the SYSTEM TEST MODE screen to display the GAME TEST MENU screen as
follows.
GAME TEST MENU
BOOKKEEPING
INPUT TEST
OUTPUT TEST
GAME ASSIGNMENTS
OPTION ASSIGNMENTS
CONTROLLER CALIBRATION SETTING
BACKUP DATA CLEAR
→ EXIT
11
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
GAME TEST MENU screen
■Controls
- Use the SERVICE Button to move the cursor to the desired test item.
- Press the TEST Button to confirm selection of the item.
- Select EXIT and press the TEST Button to return to the SYSTEM TEST MENU screen.
■Menu Items
BOOKKEEPING
Displays all recorded game data.
INPUT TEST
Tests each input device used for the game.
OUTPUT TEST
Tests each output device used for the game.
GAME ASSIGNMENTS
Adjusts all game settings.
OPTION ASSIGNMENTS
Adjusts game options.
CONTROLLER CALIBRATION SETTING
Adjusts aim settings for control units.
BACKUP DATA CLEAR
Erases all types of game records.
GAME TEST MODE
35
11-2 BOOKKEEPING
Each game record can be viewed.
BOOKKEEPING 1/3
COIN 1
COIN 2
TOTAL COINS
*
*
*
COIN CREDITS
SERVICE CREDITS
TOTAL CREDITS
*
*
*
PRESS TEST BUTTON TO NEXT
■Controls
BOOKKEEPING 1/3 screen
- Press the TEST Button to move to BOOKKEEPING 2/3 screen.
11
■Menu Items
COIN 1
Number of coins inserted in coin chute 1.
COIN 2
Number of coins inserted in coin chute 2.
TOTAL COINS
Total Number of coins inserted in coin chute.
COIN CREDITS
Number of credits for coins inserted.
SERVICE CREDITS
Number of credits entered with the SERVICE Button.
TOTAL CREDITS
Total number of all credits.
36
GAME TEST MODE
BOOKKEEPING 2/3
NUMBER OF GAMES
*
FIRST PLAY
*
CONTINUE PLAY
*
PREMIUM START CHANCE
*
EXCHANGE CHANCE
*
TOTAL TIME
*D **H **M **S
PLAY TIME
*D **H **M **S
AVERAGE PLAY TIME
*M **S
LONGEST PLAY TIME
*M **S
SHORTEST PLAY TIME
*M **S
PRESS TEST BUTTON TO NEXT
BOOKKEEPING 2/3 screen
■Controls
- Press the TEST Button to move to BOOKKEEPING 3/3 screen.
■Menu Items
11
NUMBER OF GAMES
Total number of games played by Player 1 and Player 2.
FIRST PLAY
Total number of first time plays by Player 1 and Player 2.
CONTINUE PLAY
Total number of times Player 1 and Player 2 opted to continue.
PREMIUM START CHANCE
Total number of times Player 1 and Player 2 opted for Premium Start.
EXCHANGE CHANCE
Total number of times Player 1 and Player 2 opted for Exchange Chance.
TOTAL TIME
Amount of time the cabinet has been in operation.
PLAY TIME
Amount of time the game has been played.
AVERAGE PLAY TIME
Average play time for one game.
LONGEST PLAY TIME
Longest play time for one game.
SHORTEST PLAY TIME
Shortest play time for one game.
BOOKKEEPING 3/3
GAME HISTOGRAM
0M
0M
1M
1M
00S
30S
00S
30S
-
0M
0M
1M
1M
29S
59S
29S
59S
:
:
9M 00S - 9M 29S
9M 30S - 9M 59S
OVER
10M 00S
*
*
*
*
*
*
*
PRESS TEST BUTTON TO EXIT
■Controls
BOOKKEEPING 3/3 screen
- Press the TEST Button to return to GAME TEST MENU screen.
■Menu Items
This displays play times on a scale from 0M00S to 9M59S based on 30-second intervals.
All play times 10 minutes or over are included in the item OVER 10M00S.
GAME TEST MODE
37
11-3 INPUT TEST
Select INPUT TEST to display the following screen and check the status of input devices.
This test should be used periodically to check that each input device is functioning correctly.
INPUT TEST
CONTROLLER TRIGGER
CONTROLLER X
CONTROLLER Y
SCREEN IN
START
PLAYER1
OFF
**
**
OUT
OFF
SERVICE
TEST
OFF
OFF
PLAYER2
OFF
**
**
OUT
OFF
PRESS TEST BUTTON AND
SERVICE BUTTON TO EXIT
INPUT TEST screen
11
■Controls
- The SCREEN IN setting is normal if it changes from "OUT" to "IN" when the control units are pointed at the
screen.
- Settings other than SCREEN IN are normal if they change from "OFF" to "ON" when the corresponding input
device is operated.
- Press the TEST Button and the SERVICE Button simultaneously to return to GAME TEST MENU screen.
■Menu Items
CONTROLLER TRIGGER
This will say "ON" when the triggers on the control units are being pulled and
"OFF" when they are released.
CONTROLLER X
This shows the aim location for the X direction on the control units.
CONTROLLER Y
This shows the aim location for the Y direction on the control units.
SCREEN IN
This will say "IN" when the control units are aimed inside the screen and
"OUT" when they are aimed outside the screen.
START
This will say "ON" when the START buttons are being pressed and "OFF"
when they are released.
SERVICE
This will say "ON" when the SERVICE Button is being pressed and "OFF"
when it is released.
TEST
This will say "ON" when the TEST Button is being pressed and "OFF" when it
is released.
38
GAME TEST MODE
11-4 OUTPUT TEST
This screen is for confirming the proper operation of each output device used by the game.
Periodically use this screen to check the status of each output device.
OUTPUT TEST
START1 LAMP
START2 LAMP
PANEL1 LAMP
PANEL2 LAMP
PLAYER1 CONTROLLER REACTION
PLAYER2 CONTROLLER REACTION
→ EXIT
OFF
OFF
OFF
OFF
OFF
OFF
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
OUTPUT TEST screen
■Controls
11
- Use the SERVICE Button to move the cursor to the desired test item.
- On the PANEL1/2 LAMP settings, the value changes each time the TEST Button is pressed, switching to a
different color.
- When the TEST Button is pressed for other selected items, "OFF" will change to "ON" and the corresponding
output device will operate. If the TEST Button is pressed for an item that is "ON," the device will change to "OFF"
and stop operating.
- Select EXIT and press the TEST Button. The GAME TEST MENU screen reappears.
■Menu Items
START1 LAMP
Player 1 START Button lamp.
START2 LAMP
Player 2 START Button lamp.
PANEL1 LAMP
LED panel lights up in a "+" shape. (See "1" on the figure in
below.) Cycle setting from "1" through "7" to change colors.
PANEL2 LAMP
LED panel lights up in an "X" shape. (See "2"on the figure in
below.) Cycle setting from "1" through "7" to change colors.
PLAYER1 CONTROLLER REACTION
Activates the solenoid in Player 1’s control unit. Reverts to "OFF"
after one activation.
PLAYER2 CONTROLLER REACTION
Activates the solenoid in Player 2’s control unit. Reverts to "OFF"
after one activation.
2
1
2
1
1
2
1
2
GAME TEST MODE
39
11-5 GAME ASSIGNMENTS
All settings such as level of game difficulty or mode of the game are adjusted.
GAME ASSIGNMENTS
GAME DIFFICULTY
ADVERTISE SOUND
INITIAL LIFE
MAX LIFE
RANDOM REVIVAL
PLAYER1 CONTROLLER REACTION
PLAYER2 CONTROLLER REACTION
VOICE LANGUAGE
CABINET TYPE
NORMAL
NORMAL
*
*
ON
ON
ON
ENGLISH
EUROPE
→ EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
GAME ASSIGNMENT screen
■Controls
- Use the SERVICE Button to move the cursor to the desired test item.
- Press the TEST Button to change the value of the selected setting.
- Select "EXIT" and press the TEST Button to return to the GAME TEST MENU screen.
■Menu Items
GAME DIFFICULTY
Sets the level of difficulty to one of five levels. In order of difficulty: VERY
EASY -> MEDIUM EASY ->NORMAL -> MEDIUM HARD -> VERY
HARD.
(Default setting: NORMAL)
ADVERTISE SOUND
Sets the sound level for the advertisements to one of 5 levels, from loudest to
softest: NORMAL -> 3/4 -> 1/2 -> 1/4 -> OFF.
(Default setting: NORMAL)
INITIAL LIFE
The number of LIFE(s) the player will start the game with. Can be set between
1 and 9. However, cannot be set higher than the MAX LIFE setting.
(Default setting: 3)
MAX LIFE
The maximum amount of LIFE(s) a player may have. Can be set between 1
and 9.
(Default setting: 9)
RANDOM REVIVAL
Turns RANDOM REVIVAL ON/OFF;
If set to "ON," two players cannot die at the same time.
(Setting this to "ON" extends play time, but also increases the rate of
continues.)
(Default setting: ON)
PLAYER1 /PLAYER2
CONTROLLER REACTION
Turns the reaction of player control units ON/OFF.
(Default setting: ON)
VOICE LANGUAGE
Toggles the in-game language. (ENGLISH/CHINESE)
(Default setting: ENGLISH)
CABINET TYPE
Automatically displays the cabinet type. (EUROPE/ASIA)
(REGION EXP only)
11
40
GAME TEST MODE
11-6 OPTION ASSIGNMENTS
Adjust game options.
OPTION ASSIGNMENTS
PREMIUM START CHANCE
ATK POWER +
LIFE +
MAGAZINE +
EXCHANGE CHANCE
SCORE +
CONTINUE BONUS
→ EXIT
ON
*
*
*
ON
*
ON
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
OPTION ASSIGNMENTS screen
11
■Controls
- Use the SERVICE Button to move the cursor to the desired test item.
- Select EXIT and press the TEST Button. The GAME TEST MENU screen reappears.
■Menu Items
PREMIUM
START
CHANCE
EXCHANGE
CHANCE
Set PREMIUM START CHANCE ON/OFF:
Setting to "ON" makes the Premium Start menu available at the start of the game (credits
required). Inserting additional credits awards the player bonuses as set below.
NOTE: Cannot be set to "ON" when set to FREE PLAY.
(Default setting: ON)
ATK POWER +
The level of ATTACK POWER the player will gain. Can be set
between 1 and 10. (Default setting: 2)
LIFE +
The amount of LIFE the player will gain. Can be set between 1 and 9.
(Default setting: 1)
MAGAZINE +
The number of MAGAZINEs the player will gain. Can be set between 1
and 10. (Default setting: 2)
Set EXCHANGE CHANCE ON/OFF:
Setting to "ON" allows players to exchange credits for score items at the item store screen.
Scores are worth 70% of the set value during 2-player simultaneous play.
NOTE: Cannot be set to "ON" when set to FREE PLAY.
(Default setting: ON)
SCORE +
CONTINUE
BONUS
The number of points the player will gain. Can be set between 10000
and 90000, in 10000 increments. (Default setting: 10000)
Set CONTINUE BONUS ON/OFF.
Setting to "ON" allows players to get bonus items when continuing.
NOTE: The CONTINUE BONUS setting is not displayed for CABINET TYPE EUROPE;
the setting defaults to "OFF" for CABINET TYPE ASIA. Cannot be set to "ON" when set to
FREE PLAY.
GAME TEST MODE
41
11-7 CONTROLLER CALIBRATION SETTING
This screen allows for the adjustment of the control unit’s crosshair settings which are used during game play.
CONTROLLER CALIBRATION SETTING
CONTROLLER MARK CHECK
PLAYER1 CONTROLLER ADJUSTMENT
PLAYER1 CONTROLLER DEFAULT ADJUSTMENT
PLAYER2 CONTROLLER ADJUSTMENT
PLAYER2 CONTROLLER DEFAULT ADJUSTMENT
→ EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
CONTROLLER CALIBRATION SETTING screen
■Controls
- Use the SERVICE Button to move the cursor to the desired test item.
- Press the TEST Button to change the value of the selected setting.
- To abort calibration, press the TEST Button to cancel.
- Select EXIT and press the TEST Button. The GAME TEST MENU screen reappears.
■Menu Items
CONTROLLER MARK CHECK
Checks the gun sights. P1 and P2 control units are checked at
the same time.
PLAYER1 / PLAYER2
CONTROLLER ADJUSTMENT
Calibrates Player 1 and Player 2 control units.
PLAYER1 / PLAYER 2
CONTROLLER DEFAULT ADJUSTMENT
Resets Player 1 and Player 2 control units to their factory
default settings.
11
42
GAME TEST MODE
CONTROLLER MARK CHECK
Check the marks (targeting sights) for Players 1 and 2.
CONTROLLER MARK CHECK
+OUT OF SCREEN P2+
Displayed if PLAYER 2
control unit is pointed
outside the screen.
P1 MARK (blue)
(P2 MARK is displayed in red)
PRESS TEST BUTTON TO EXIT
CONTROLLER MARK CHECK screen
■Controls
11
-Point the control units at the screen to display the marks (targeting sights).
-"OUT OF SCREEN" is displayed when the control units are pointed outside the screen.
-Press the TEST Button to return to the CONTROLLER CALIBRATION SETTING screen.
PLAYER1 / PLAYER2 CONTROLLER ADJUSTMENT
Calibrate PLAYER 1/PLAYER 2 control units.
(The below image shows the calibration screen for Player 1. The screen for Player 2 is the same.)
PLAYER1 CONTROLLER ADJUSTMENT
GRID
PLEASE SHOOT GRID WITH
PLAYER1 CONTROLLER
PRESS TEST BUTTON TO EXIT
CONTROLLER ADJUSTMENT screen
■Controls
1
2
3
Align the top of the groove on the control unit’s rear sight with the horizontal line of the plus sign on the
screen.
Align the top of the control unit’s front sight with the horizontal line as well.
Pull the trigger when the top of the rear sight and top of the front sight line up with the center of the plus
sign on the screen.
GAME TEST MODE
4
5
43
Shoot the upper left, then the lower right, and finally the center of the screen to complete the process. The
screen will display "NOW CALCULATING.".
When the calibration screen is complete, check to make sure the mark (targeting sight) is properly
displayed.
PLAYER1 CONTROLLER ADJUSTMENT
PLAYER1 CONTROLLER MARK CHECKING
MARK
TEST BUTTON
: TO MEMORIZE
SERVICE BUTTON : TO CANCEL
CONROLLER ADJUSTMENT screen (MARK CHECK)
6
Press the TEST Button to save calibration settings and return to the CONTROLLER CALIBRATION
SETTING screen. Press the SERVICE Button to exit to the CONTROLLER CALIBRATION SETTING
screen without saving calibration settings.
DEFAULT ADJUSTMENT
Set the values for the control units to default.
PLAYER1 CONTROLLER ADJUSTMENT
TEST BUTTON
: TO SET DEFAULT
SERVICE BUTTON : TO CANCEL
DEFAULT ADJUSTMENT screen
■Controls
- Press the TEST Button to reset settings to their factory defaults. The screen will display "COMPLETED". Press the
TEST Button again to return to the CONTROLLER CALIBRATION SETTING screen.
- Press the SERVICE Button to exit to the CONTROLLER CALIBRATION SETTING screen without resetting
calibration settings to default.
11
44
GAME TEST MODE
11-8 BACKUP DATA CLEAR
Delete various game data.
BACKUP DATA CLEAR
YES (CLEAR)
-> NO (CANCEL)
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
BACKUP DATA CLEAR screen (1/2)
11
BACKUP DATA CLEAR
COMPLETED
PRESS TEST BUTTON TO EXIT
BACKUP DATA CLEAR screen (2/2)
■Controls
- Use the SERVICE Button to move the cursor to the desired test item.
- Select "YES (CLEAR)" and press the TEST Button to clear game operational data. Once data is cleared, the screen
will display "COMPLETED". Press the TEST Button again to return to the GAME TEST MENU screen.
- Select "NO (CANCEL)" and press the TEST Button to return to the GAME TEST MENU screen without clearing
data.
CONTROL PANEL
45
12 CONTROL PANEL
● Before starting to work,, be sure to turn the power off. Without turning the power
off can cause an electric shock or short circuit.
● Be careful not to damage the wires. Damaged wires may cause electric shock or
short circuit or present a risk of fire.
12-1 REMOVING THE CONTROL PANEL
1
2
Turn the power off.
Remove the 4 tamper screws.
12
Tamper Scres(4)
3
Lift the front side of the control panel and then
pull the back forward. At this point, the connector on the back of the control panel is still attached, so do
not force it.
46
CONTROL PANEL
4
Disconnect the connector and take the control
panel off.
CONNECTOR
YL8P
12-2 REPLACING THE START BUTTON
12
1
2
Refer to 12-1 "REMOVING THE CONTROL PANEL" to take the control panel off.
Disconnect the connector from the switch.
NOTE: The 1P and 2P START buttons are
distinguished by a stamp.
CONNECTOR
SM4P
3
Turn the switch about 45 degrees in a
counterclockwise direction and pull it out.
CONTROL PANEL
4
47
Remove the plastic nut and take off the stopper and the button.
NOTE: When ordering a replacement start button, order part number 509-6077.
BUTTON
STOPPER
PLASTIC NUT
BUTTON
STOPPER
PLASTIC NUT
SWITCH
START BUTTON (509-6077)
12
48
DLP PROJECTOR
13 LCD unit
The LCD is adjusted when shipping from the factory. Avoid any unnecessary
adjustment. Failure to observe this can have a bad influence upon the players' or
the customers' physical conditions.
● If the adjustment method in this manual does not resolve the problem contact the
customer service number in this manual or your supplier.
● There is no way of knowing when the LCD light is going to cease to function.
Once it ceases to function, the LCD unit will be unable to display anything and the
product cannot be used.
● Do not stick tape, stickers or anything else onto the screen. Any kind of adhesive
may damage the surface of the screen.
13
DLP PROJECTOR
49
13-1 CLEANING THE SCREEN
Since the LCD screen is susceptible to damage, pay careful attention to its handling.
Do not clean the screen with volatile chemicals, solvents or alkaline/acidic cleaners.
Clean the screen surface once a week.
Dip a soft cloth in water 40 degrees or below, wring it out firmly, and use it to gently wipe the screen.
If there are stains that can’t be removed with warm water, use a neutral detergent diluted to 2-3%.
Refrain from using other chemicals, solvents, bleaches and cleaners because they may affect the screen.
Also do not use chemically-treated cloths.
The screen is easily damaged, so avoid scratching it with hard objects or striking it with a duster or other objects.
If the stains are serious, contact the office detailed in this manual or the point-of-purchase for this product.
13
50
CONTROL UNIT
14 CONTROL UNIT
● Before starting to work, be sure to turn the power off. Without turning the power
off can cause an electric shock or short circuit.
● Be careful not to damage the wires. Damaged wires may cause electric shock or
short circuit or present a risk of fire.
● Exercise due caution in performing soldering procedures. If soldering iron is
handled carelessly, there could be fires or burns.
● When fastening plastic parts, be careful not to tighten screws and nuts
excessively. Failure to observe this may damage the parts and cause injury due
to fragments resulting from damage.
● After the unit has been disassembled and reassembled again, check carefully
to be sure that there are no gaps or rattling at the junctions and that the trigger
can be operated smoothly. If there are gaps or rattling, or if operation is not
satisfactory, the players could get fingers or hands caught, resulting in injury.
14
● Be sure to inspect control unit surfaces for cracks and damage. Players could
be injured if they play when the unit is cracked or damaged.
● Assemble so that there is no gap between the L and R covers. If there is a gap or
rattling, the players could get fingers or hands caught, resulting in injury.
●Do not cut the tie that holds the wires together inside the control unit. Doing
so can lead to connection failures with the connectors inside the unit. If the tie
must be cut to replace wires or perform other such work, make sure that they are
returned to the original position and tied together again.
●Once the product has been disassembled, use slack preventive agent (product
No. : 090-0012-N). Coat screws with suitable amounts of this agent and then
tighten them. If this agent is not used, the product might start rattling or come
apart.
●Use the slack preventive agent prescribed in these instructions. If any other
agent is used, there could be chemical changes that inhibit the use of screws and
part surfaces could be damaged.
●Be careful not to damage or lose small parts or screws.
●When a part has been replaced, be sure to always make adjustments and check
conditions in TEST MODE.
CONTROL UNIT
51
If the control unit does not operate satisfactorily and adjustments in TEST MODE are ineffective, it could be that
parts inside the control unit have been damaged.
Follow the steps given below to remove the control unit, then take it apart and replace parts.
To replace parts in the control unit, detach the L and R covers of the outer part.
Because internal parts are inserted on the R cover side, work with the R cover facing downward.
14
52
CONTROL UNIT
14-1 REMOVING THE CONTROL UNIT
Remove the 1P and 2P control units.
1P CONTROL UNIT
2P CONTROL UNIT
1
2
Turn the power off.
Remove the 4 screws and pull out the control unit’s connector.
14
SCREW (4), black
NOTE: When attaching, confirm the direction of the bracket and the cable.
CONTROL UNIT
3
4
53
Disconnect the connector and take the control
unit off.
Remove the screw and take the controller cable bracket off.
SCREW (1)
M4 x 8, w/flat & spring washers
CONTROLLER CABLE BRACKET
14
54
CONTROL UNIT
14-2 REPLACING THE MICROSWICH
There are microswitches for the trigger and button inside the control unit.
1
3 kinds of screws are used to fasten the L and R covers in place. Remove the 10 screws and separate the L
and R covers.
SCREW (8), black
M3 x 12, w/small flat &
spring washers
SCREW (1), black
M3 x 10, w/small flat &
spring washers
COUNTERSUNKHEAD SCREW (1), black
M3 x 8
2
3
Place cover R face down on the work surface and slowly lift cover L directly upward.
Remove the trigger microswitch from the R
cover.
14
TRIGGER MICROSWITCH
509-5080
4
5
6
7
Remove the soldered part and then remove the microswitch.
Solder and attach the new button microswitch. Protect the soldered part with heat-shrinkable tubing.
After replacing the microswitch, re-assemble the control unit. Confirm the microswitches turn on and off
properly by pulling the trigger and pushing the button and then attach the L and R covers. Be careful not to
tighten screws excessively.
Refer to 11-3 "INPUT TEST" and perform the input test.
CONTROL UNIT
55
14-3 REPLACING THE SENSOR UNIT
1
2
Refer to 14-2 "REPLACING THE MICROSWITCH" and remove the cover L.
Disconnect the connector and take the sensor
unit off.
SENSOR UNIT
GLG-2130
CONNECTOR
XA9P
3
4
After replacing the sensor unit, re-assemble the control unit. Confirm the microswitches turn on and off
properly by pulling the trigger and pushing the button and then attach the L and R covers. Be careful not to
tighten screws excessively.
Refer to 11-7 "CONTROLLER CALIBRATION SETTING" and perform the aim adjustment.
14
56
CONTROL UNIT
14-4 REPLACING THE SOLENOID
1
2
Refer to 14-2 "REPLACING THE MICROSWITCH" and remove the cover L.
Undo the cord clamp and disconnect the connector.
CONNECTOR
SM2P
3
14
Remove the 2 screws and take the solenoid unit off.
SCREW (2)
M4 x 8, w/flat & spring washers
SOLENOID UNIT
4
Be careful not lose or damage the spring and other
small parts when removing the solenoid unit.
CONTROL UNIT
5
Remove the 8 screws and the E-ring (2 mm), and replace the solenoid. Be careful not to lose small parts.
SCREW (8)
M3 x 8, w/spring washer
6
57
SOLENOID
124-5101
E-RING
2 mm
Refer to Step 2 to Step 5 and work in reverse order to affix the solenoid unit. Refer to the drawing below
and be careful with the order in which the small parts are attached and the direction the side with the
solenoid wire faces. Attaching the parts the wrong way may result in malfunction of the unit or pinching of
the wire.
14
7
8
After replacing the solenoid, re-assemble the control unit. Confirm the microswitches turn on and off
properly by pulling the trigger and pushing the button and then attach the L and R covers. Be careful not to
tighten screws excessively.
Refer to 11-4 "OUTPUT TEST"and perform the output test.
58
COIN SELECTOR
15 COIN SELECTOR
●Remove and clean smears using a soft cloth dipped in water or diluted chemical
detergent which is then wrung dry.
●Never apply machine oil, greace, etc. to the coin selector.
●After cleaning the coin selector, properly insert a standard coin to ensure that the
selector functions correctly.
15-1 CLEANING THE COIN SELECTOR
The coin selector should be cleaned once per month. When cleaning, follow the procedures below:
1
2
Turn the power off. Open coin chute door.
Open gate and wipe away dirt with animal hairbrush or other soft brush.
15
3
4
5
6
Soak a soft cloth in water or in a neutral cleaning agent diluted with water, wring it tightly and wipe away
dirt.
Remove cradle. When removing the retaining ring
(E ring), be careful not to bend the rotary shaft.
Use soft cloth to wipe dirt from rotary shaft and bearing.
After wiping off dirt, wipe away moisture with a dry cloth and make sure that the coin selector is
completely dry.
COIN SELECTOR
59
15-2 REMOVING THE JAMMED COIN
When the REJECT button fails to refund coins, open the coin chute door and open the selector gate. Once the
jammed coin is removed, insert a standard coin to ensure that the selector is working properly.
15-3 COIN INSERTION TEST
Carry out a coin insertion test once per month. At the same time, check the following points:
□ Does the coin meter count properly?
□ Do coins drop into the cashbox correctly?
□ Are coins rejected when inserted while holding down the REJECT button?
□ Are extra coins and incorrect coins properly returned?
COIN INSERTION SLOT
REJECT BUTTON
15
COIN RETURN SLOT
60
FLUORESCENT LAMP REPLACEMENT
16 FLUORESCENT LAMP REPLACEMENT
● Before starting to work, be sure to turn the power off. Without turning the power
off can cause an electric shock or short circuit.
● You may get burned by a hot fluorescent lamp or other lamps. Pay full attention
to the lamps when performing the work.
● Be sure to use lamps meeting specified rating. Using lamps exceeding the
specified rating can cause fire and/or accident.
● Such things as deteriorated insulation in lighting fixtures can cause a short
circuit and/or smoke. Make sure there are no abnormalities. For example, check
if you can smell anything burning, if any sockets have been discolored and if the
lamp has to be replaced frequently.
● To perform work safely and securely, be sure to prepare a stepstool which is in
a secure and stable condition. Performing work without using the stepstool can
cause violent falling down accidents.
● When fastening plastic parts, be careful not to tighten screws and nuts
excessively.
16
FLUORESCENT LAMP REPLACEMENT
61
16-1 BILLBOARD
1
2
3
4
Turn the power off.
Unscrew the 3 screws,
to remove glass holder bracket.
Stand on a stepstool when replacing FL unit. For safety reasons, this should be done together with at least
2 people.
Replace the fluorescent lamp.
NOTE: Replace the glow lamp if necessary.
16
62
REPLACING THE FUSE
17 REPLACING THE FUSE
● In case fuse replacements other than those stated in this manual are necessary,
contact where you purchased the product from for inquiries regarding this
matter.
● In order to prevent an electric shock, be sure to turn power off and unplug from
the socket outlet before performing work by touching the internal parts of the
product.
● Be careful not to damage the wire. Damaged wires may cause electric shock or
short circuit or present a fire risk.
● Be sure to use fuses meeting specified rating. Using fuses exceeding the
specified rating can cause fire and electric shock accidents.
● After eliminating the cause of the blowing of fuse, replace the fuse. Depending
on the cause of fuse blowing, continued use with the fuse as is blown can cause
generation of heat and fire hazard.
For continued protection against risk of fire, replace only with the same type of
fuse having the same electrical ratings.
17
1
2
Turn the power off.
Remove the 8 screws, and remove back cover.
REPLACING THE FUSE
3
63
Replace the fuse.
FUSE 250 V 0.2 A (1P SENSOR UNIT)
514-5143-200
FUSE 250 V 2 A (1P SOLENOID)
514-5143-2000
FUSE 250 V 0.2 A (2P SENSOR UNIT)
514-5143-200
FUSE 250 V 2 A (2P SOLENOID)
514-5143-2000
17
64
PERIODIC INSPECTION
18 PERIODIC INSPECTION
The items listed below require periodic check and maintenance to retain the performance of this machine and to
ensure safe business operation.
Players operate the control unit by touching it and holding it with their hands. Clean the control unit on a regular
basis and have hand wipes, etc. available to ensure that players will always fully enjoy the game.
● Have work performed by site maintenance personnel or other qualified
individuals. Do not allow people without proper knowledge and technical
expertise to work on the product. Otherwise there could be an electric shock
or other serious accident. Also, customers could be injured while operating the
product.
● Be sure to check once a year to see whether power cables are damaged, the
plug is securely inserted, dust has accumulated between the socket outlet and
the power plug, etc. Using the product with accumulated dust can cause fire and
electric shock.
● Periodically, around once a year, get in touch with the place of contact herein
stated or the Distributor, etc. where the product was purchased from, regarding
internal cleaning. Using the product with accumulated dust in the interior can
cause a fire or accident. Note that professional cleaning will require a fee.
● There is the danger of accidents involving electrical shorts circuits or fire caused
by factors such as the deterioration of insulation in electrical and electronic
equipment over time. Check that there are no anomalies such as odors from
burning.
● Before starting to work, be sure to turn the power off. Without turning the power
off can cause an electric shock or short circuit.
18
● Do not clean the product with a water jet or water cannon. The product has not
been designed for water jet cleaning. Water infiltration can cause electric shock
or short circuit. It will also cause damage that is difficult to repair.
PERIODIC INSPECTION
65
■ PERIODIC INSPECTION TABLE
ITEMS
DESCRIPTION
PERIOD
REFERENCE
CABINET
Confirm that adjusters
contact floor
Daily
Chapter 3
CONTROL UNIT
Cleaning
As appropriate
-
Aim test
Weekly
Chapter 11
Microswitch test
Monthly
Chapter 14
Coin switch inspection
Monthly
Chapter 15
Coin insertion test
Monthly
15-3
Cleaning
Monthly
15-1
Screen cleaning
Weekly
13-1
Check screen adjustment
Monthly or when
moving
13-2
Memory test
Monthly
“S/M”
Settings check
Monthly
“S/M”
Cleaning
Every 3 months
20-2
POWER CABLE
Inspection, Cleaning
1 year
6-8
CABINET INTERIOR
Cleaning
1 year
As above
CABINET SURFACES
Cleaning
As appropriate
See below
COIN SELECTOR
LCD UNIT
RINGWIDE
NOTE: The “S/M” referenced in the table denotes RINGWIDE Service Manual, which is provided separately.
Cleaning the Cabinet Surfaces
When the cabinet surfaces become dirty, remove stains with a soft cloth soaked in water or diluted (with water)
chemical detergent and then wrung dry. To avoid damaging the finish, do not use such solvents as thinner, benzene,
etc. (other than ethyl alcohol) or abrasives (bleaching agent and chemical dust-cloth).
Some general-purpose household, kitchen, and furniture cleaning products may contain strong solvents that degrade
plastic parts, coatings, and print. Before using any cleaning product, read the product's cautionary notes carefully
and test the product first on a small area that is not highly visible.
18
66
TROUBLESHOOTING
19 TROUBLESHOOTING
● If problems other than those covered in this manual arise, or if no improvements
can be noted after measures given in this manual have been taken, do not
take measures indiscriminately. Cut off the power immediately and contact the
office shown in this manual or the dealer from whom the product was originally
purchased. If the power is left on while there is an abnormality, a fire, electric
shock or other serious accident can occur.
● Before starting to work, be sure to turn the power off. Without turning the power
off can cause an electric shock or short circuit.
● Be careful not to damage the wires. Damaged wires may cause electric shock or
short circuit or present a risk of fire.
● After the cause of circuit protector activation has been removed, have the circuit
protector re-engaged. If the unit is used continuously as is, there could be heat
generation or fire, depending on the cause of the activation.
● Have work performed by site maintenance personnel or other qualified
individuals. Do not allow people without proper knowledge and technical
expertise to work on the product. Otherwise there could be an electric shock
or other serious accident. Also, customers could be injured while operating the
product.
If a problem occurs, first inspect the connection of any wiring connectors.
19
TROUBLESHOOTING
67
19-1 TROUBLESHOOTING TABLE
PROBLEMS
CAUSE
With main switch ON, no
activation.
Power is not supplied.
Securely insert the power plug into
the plug socket.
Power supply/voltage is not correct.
Make sure that power supply/
voltage is correct.
The circuit protector functioned due
to the momentary overload.
After eliminating the cause of
overload, reinstate the AC unit’s
circuit protector.
<See 6-8, see below>
Faulty adjustment of sound volume.
Adjust the sound volume.
<See Chapter 9>
Failure of the Board and Amplifier.
Contact the customer service center
listed in this manual.
Sights are not aligned due to
changes in the surrounding
environment.
Perform sighting adjustment in the
TEST MODE.<See 6-10>
Failure of the LED board.
Check to ensure that the LED lights
up. If it does not light up, replace.
<See 19-2>
Failure of the sensor unit.
Replace the sensor unit.
(GLG-2130 SENSOR UNIT)
<See Chapter 14-3>
LED board and LED board cover
are contaminated.
Wipe off soiled surfaces.
Failure of the microswitches.
Use an Input Test to make sure they
change between ON and OFF. If
they do not, exchange the faulty
microswitches. (509-5080 SW
MICRO TYPE)
<See 14-2>
Failure of the LED board.
Check that the LEDs are on. If not,
replace them. <See 19-2>
Failure of the sensor unit.
Replace the sensor unit. <See 14-3>
Fluorescent lamp and glow lamp
need replacement.
Replace the fluorescent lamp/grow
lamp. <See Chapter 16>
Fuse need replacement.
Replace the fuse.<See Chapter 17>
No sound is generated from the
speaker.
The control unit sighting is not
satisfactory.
The control unit does not appear to
be operating correctly.
Fluorescent lamp does not
illuminate.
COUNTERMEASURES
19
68
TROUBLESHOOTING
19-2 REPLACING THE LED BOARD
Removing or attaching of the mask must be carried out by at least 2 people, one
on the left and one on the right. A single person working alone can lead to injury.
If the light from the 2 LEDs cannot be seen then there is a problem or malfunction. Follow the steps below to
exchange them. You can also use the following steps to clean the screen.
1
Turn the power off.
Replacement is required when the light from
2 LEDs cannot be seen.
2
Unscrew 7 screws on both side of monitor cover.
19
3
Unscrew 4 screws on top of monitor cover..
TROUBLESHOOTING
4
69
CONNECTOR
VL1P
Disconnect the 2 connectors.
CONNECTOR
SM6P
5
The mask has the LED boards attached. Remove the 2 U nuts holding the malfunctioning board,
disconnect both connectors and remove and replace the LED board. Be sure not to lose the plastic washers.
Attach the LED board after checking to make sure it is facing the same way as before.
19
70
TROUBLESHOOTING
5
6
19
7
The mask has the LED boards attached. Remove the 2 U nuts holding the malfunctioning board,
disconnect both connectors and remove and replace the LED board. Be sure not to lose the plastic washers.
Attach the LED board after checking to make sure it is facing the same way as before.
If the problematic LED board is in the corner of the mask remove the 5 screws and remove the joint
bracket. The joint bracket has the same parts are the boards along the straight sections of the mask, and
there are 2 types.
After exchanging the LED board enter TEST MODE and perform a controller adjustment. (See 11-7.)
RINGWIDE
71
20 RINGWIDE
● Before starting to work, be sure to turn the power off. Without turning the power
off can cause an electric shock or short circuit.
● Be careful not to damage the wires. Damaged wires may cause electric shock or
short circuit or present a risk of fire.
● Do not expose the game board, etc. Failure to observe this can cause electric
shock hazard or malfunctioning.
● This product does not use any connectors other than those connected to and
used by the game board when it leaves the factory. Do not needlessly connect
wires to unused connectors. This could lead to overheating, generation of
smoke and burn related injuries.
● Have work performed by site maintenance personnel or other qualified
individuals. Do not allow people without proper knowledge and technical
expertise to work on the product. Otherwise there could be an electric shock
or other serious accident. Also, customers could be injured while operating the
product.
● When returning the game board after making repairs or replacements, make sure
that there are no errors in the connection of connectors. Erroneous connections
can lead to electrical shock, short circuits or fires.
● When connecting a connector, check the direction carefully. Connectors must
be connected in only one direction. If indiscriminate loads are applied in making
connections, the connector or its terminal fixtures could be damaged, resulting
in electrical shock, short circuits or fires.
When opening/closing or attaching or removing the doors or the other parts, be
careful that your hand or finger does not get caught in anything.
20
●Static electricity from human body may damage some electronics devices. Before
handling starting to work, touch a grounded metallic surface so that the static
electricity can be discharged.
●The product’s settings are changed in TEST MODE. If using only one machine,
the RINGWIDE DIP SW setting does not need to be configured. Leave RINGWIDE
on the default setting. Changing it could cause malfunctions or damage to the
parts.
72
RINGWIDE
20-1 REMOVING THE RINGWIDE
The RINGWIDE is inside the left side front door of the cabinet on the left side when facing the screen. Remove the
entire wooden board (ASSY MAIN BD) on which the RINGWIDE is placed.
1
2
3
20
4
Turn the power off.
Unscrew 8 screws, and remove back cover
Disconnect all connecters connected to the RINGWIDE.
Remove the 4 screws and take the RINGWIDE off.
RINGWIDE
73
20-2 CLEANING THE RINGWIDE
Clean the RINGWIDE once a year or when "Error 0090" or "Error 0091" is displayed.
If dust accumulates inside the RINGWIDE, it could lead to malfunction and other
trouble.
Take the RINGWIDE off once a year and use a vacuum cleaner to clean the areas around the intake and exhaust
vents and where it is attached to the cabinet.
1
2
Refer to 20-1 "REMOVING THE RINGWIDE" and take the RINGWIDE off from the cabinet.
Clean around the air vent of the RINGWIDE with a vacuum cleaner.
AIR INTAKE
EXHAUST VENT
3
4
EXHAUST VENT
Clean around installment parts of the RINGWIDE in the cabinet with a vacuum cleaner. Be sure not to
damage wirings and boards. Electronic devices on boards may damage by static electricity, and be sure not
to vacuum electronic devices by a vacuum cleaner.
Refer to 20-1 "REMOVING THE RINGWIDE" and work in reverse order to attach the RINGWIDE to the
cabinet.
20
74
RINGWIDE
20-3 COMPOSITION OF THE RINGWIDE
●The RINGWIDE becomes the RINGWIDE for this product once the key chip is
inserted.
●The DIP SW (dip switches) on the RINGWIDE must be set as specified below. If
set incorrectly for this product, an error will be displayed and the game will not
run.
ASSY CASE WDE W 1GB USA (847-0001D-01)
DIP SW Setting
Use this product with the DIP SW settings shown in the figure below.
Pin
Setting
20
1
2
3
4
5
6
7
8
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
DESIGN RELATED PARTS
75
21 DESIGN RELATED PARTS
21
76
PARTS LIST
22 PARTS LIST
(1) ELECTRONIC PARTS
(2) CONTROL PANEL
22
PARTS LIST
(3) GLG-0550
ASSY MASK
77
(D-1/2)
22
78
PARTS LIST
(3) GLG-0550
ASSY MASK
22
(D-2/2)
ITEM NO.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
101
102
201
202
203
204
205
206
207
301
302
303
304
RMB-0551
HDF-0531
HDF-0532
HDF-0534
HDF-0535
JPT-1082X
GLG-0551
GLG-0552
SIDE MASK
UPPER MASK
LOWER MASK
MASK JOINT BRKT L
MASK JOINT BRKT R
IR COVER
STICKER MASK LONG
STICKER MASK SHORT
838-15119
280-5009-02-91
LED BD HFN G.SENSE GLG
CORD CLAMP 21 CN
000-P00408-W
050-U00300
069-000034-PN
FAS-680016
050-H00400
060-S00400
060-F00400
M SCR PH W/FS M4x8
U NUT M3
FLT WSHR PLASTIC BLK 3-8x1
FLT WSHR NI 3-10x0.5
HEX NUT M4
SPR WSHR M4
FLT WSHR M4
GLG-60029
GLG-60030
GLG-60031
600-7010-0300
WH MASK1
WH MASK2
WH MASK3
WIRE HARN EARTH VL1P P 0300MM
NOTE
PARTS LIST
79
(5) GLG-2050
ASSY LED
ITEM NO.
PART NO.
DESCRIPTION
1
101
102
GLG-2052
LED BRKT
838-14973-02
280-7896-05
LED BD RGB 3x2BLOCK
SPACER WN-05G (HIROSUGI)
NOTE
22
80
PARTS LIST
(6) GLG-2060
ASSY BUTTON PLATE
22
ITEM NO.
PART NO.
DESCRIPTION
1
2
101
301
GLG-2061
421-12771
BUTTON PLATE
STICKER DENOMI BLANK
509-6077
SW PB OBSA-45UM-W-1FLED-W-12V
GLG-60025
WH START BUTTON PLATE
NOTE
PARTS LIST
(27)GLG-2100
CONTROL UNIT
81
(D-1/2)
22
82
PARTS LIST
(27)GLG-2100-01
CONTROL UNIT
22
(D-2/2)
ITEM NO.
PART NO.
DESCRIPTION
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
101
102
103
104
201
202
203
204
205
206
207
208
301
GLG-2130
APA-2101-04
APA-2102-04
APA-2103-01
APA-2104-04
APA-2106-03
APA-2107
APA-2108
APA-2109
APA-2110-01
APA-2111
APA-2112
APA-2113
APA-2114
APA-2115
APA-2116
APA-2117
APA-2118
APA-2119
APA-2123-01
APA-2124
APA-2120
CTF-2123
SENSOR UNIT (OMJ-GZH200HFXA)
COVER LEFT GOLD
COVER RIGHT GOLD
TRIGGER GOLD
SIGHT GOLD
CORD FRAME COVER GOLD
CORD CLAMP
CORD FRAME
SOLENOID FRAME
SLIDE FRAME
SOLENOID DAMPER
SOLENOID SPRING
SOLENOID SHAFT
SOLENOID WSHR
WEIGHT
DAMPER COLLAR
WEIGHT SPRING
WEIGHT WSHR
SLIDE BASE UPPER
BUSH
PLUG CUSHION
SLIDE BASE LOWER
TRIGGER SPRING
509-5080
310-5029-D20
124-5101-91
280-7881
SW MICRO TYPE (SS-5GL2)
SUMITUBE F D 20MM
SOLENOID DC24V
CORD CLAMP SR10 CN
000-P00408-W
FAS-000188
FAS-000100
FAS-000099
FAS-290110
000-F00308-0B
065-E00200
060-S00300
M SCR PH W/FS M4x8
M SCR PH W/SMALL FS BLK M4x8
M SCR PH W/SMALL FS BLK M3x12
M SCR PH W/SMALL FS BLK M3x10
HEX SKT ELH CAP STN M3x8
M SCR FH BLK M3x8
E RING 2MM
SPR WSHR M3
APA-60035X
WH CONTROLLER
NOTE
WIRE COLOR CODE TABLE
83
23 WIRE COLOR CODE TABLE
The DC power wire color for this product is different from previous SEGA titles.
Working from the previous wire colors will create a high risk of fire.
The color codes for the wires used in the diagrams in the following chapter are as follows.
A
B
C
D
E
PINK
SKY BLUE
BROWN
PURPLE
LIGHT GREEN
Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.
1
2
3
4
5
7
8
9
RED
BLUE
YELLOW
GREEN
WHITE
ORANGE
BLACK
GRAY
If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side
numeral (see the above).
Note 1: If the right-hand side numeral is not 0, that particular wire has a spiral color code. The left-hand side
character shows the base color and the right-hand side one, the spiral color.
<Example> 51………WHITE/RED
RED
WHITE
Note 2: The character following the wire color code indicates the size of the wire.
U: K: L: None: AWG16
AWG18
AWG20
AWG22
23
WIRING DIAGRAM
24 WIRING DIAGRAM
84
(D-1/3)
24
WIRING DIAGRAM
85
(D-2/3)
24
WIRING DIAGRAM
86
(D-3/3)
24
SEGA AMUSEMENTS OFFICES
SEGA AMUSEMENTS U.S.A., INC.
800 Arthur Avenue, Elk Grove Village, IL 60007-5215, U.S.A.
Telephone: +1-847-364-9787
Toll free:
+1-888-877-2669
Facsimile: +1-847-427-1065
SEGA AMUSEMENTS EUROPE, LTD.
42, Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY United Kingdom
Telephone: +44 (0) 208 391 8090
Facsimile: +44 (0) 208 391 8099
e-mail: [email protected]
http://www.sega-amusements.co.uk
SEGA CORPORATION
TRC Haneda Building, 2-13-1, Higashikojiya, Ohta-ku, Tokyo 144-0033, Japan
Telephone: +81-3-6863-8401
Facsimile: +81-3-6863-8407
1ST PRINTING
2011.03
">