BOB | Duallie | Instruction manual | BOB Duallie Instruction manual

BOB Duallie Instruction manual
BRITAX RÖMER Kindersicherheit GmbH
Blaubeurer Straße 71, 89077 ULM, Germany
SPORT UTILITY STROLLER DUALLIE
IRONMAN DUALLIE
ENGLISH
Owner’s Instruction Manual
READ AND UNDERSTAND THESE
INSTRUCTIONS COMPLETELY!
IMPORTANT - KEEP THESE
INSTRUCTIONS FOR FUTURE
REFERENCE
Before attempting to assemble or use your
new stroller, read and understand these
assembly and use instructions completely,
as well as the warnings at the beginning
and throughout this document, to ensure
proper assembly and operation.
If you are unclear on any point, contact
your dealer or BRITAX before use.
For a list of dealers, visit www.bobgear.eu
WARNINGS
• If your stroller is to be used by other
people who are not familiar with it
(such as grandparents),always show
them how the stroller is used.
• Accessories which are not approved
by BOB shall not be used.
• This product is not suitable...
- as a substitute for a bed or cot.
Strollers and pushchairs may only be
used for transport.
- for more than two children.
- for commercial use.
- as a travel system in combination
with other infant carriers.
• Ensure that all the locking devices
are engaged before use.
• When carrying the stroller, make sure
you do not open the safety locks by
mistake.
• Never allow occupants to stand in
stroller. Stroller can tip over.
• Always use wrist strap to prevent
being separated from stroller.
• Any load attached to the handle
affects the stability of the pushchair.
• Do not attach parcels or bags to the
handlebar or frame of stroller except
those recommended by BOB.
• Do not place sharp objects in the
seat back pocket. Leaning against
sharp objects in seat back pocket
can result in injury to occupants.
• When starting out and during use,
always make sure the children´s
hands and feet are away from
wheels.
• Do not use stroller on stairs or steep
inclines. Stroller can tip over.
• Never use with low tire pressure or
deflated tires as this could result in
loss of control.
• Never pull stroller backward up
stairs. Doing so could damage the
suspension system, leading to frame
failure.
• Use extreme caution when using
stroller on uneven and/or unpaved,
wet or slick surfaces, as these
conditions create additional hazards
and can lead to a loss of stability.
• Do not modify the stroller or any
•
•
•
•
•
•
•
•
•
•
•
•
•
•
labels. Doing so voids the warranty
and could lead to a dangerous
condition.
Protect stroller when transporting
or shipping to prevent damage to
stroller and stroller components.
Check closely for damage after
transporting or shipping.Discontinue
using stroller if damaged or if any
parts are missing.
Never fold the stroller when a child is
sitting in it.
To avoid injury ensure that your
children are kept away when folding
and unfolding this product
Always use the restraint system.
Never leave your children
unattended.
Always engage the brake when you
park the stroller, before you put your
child into it and before you remove
your children.
When making adjustments, make
sure your children cannot reach into
moving parts.
Protect your children from strong
sunlight. The hood does not provide
complete protection from dangerous
UV rays.
The stroller is not equipped for use
in low light or after dark.
Failure to properly assemble or
install the quick release wheels on
this stroller may result in the wheels
becoming detached while moving
and a subsequent loss of control.
The parking brake is not designed
as a stopping brake. The brake
should not be used to slow or stop
the stroller because doing so could
cause the stroller to stop abruptly,
resulting in loss of control.
Do not park on inclines. The parking
brake is intended to park the stroller
on flat surfaces only. Parking on
inclines may result in tip over or
runaway stroller.
Check that the pram body or seat
unit or car seat attachment devices
are correctly engaged before use.
Always re-adjust the harness when
26
WARNINGS
•
•
•
•
•
changing the seating position of
your children.
When seat is fully reclined, backward
tip over is more likely.
Do not exceed the maximum weight
limit of 1 kg for each of the backrest
pockets.
Do not exceed the maximum weight
limit of 4 kg for the shopping basket.
Do not let your children play with
this product.
This seat unit is not suitable for
children under 6 months.
27
TABLE OF CONTENTS
WARNINGS
Page 26
TABLE OF CONTENTS
Page 28
STROLLER ANATOMY
Page 29
AGE RECOMMENDATIONS
Page 30
STROLLER ASSEMBLY
Page 30
Unpack Stroller
Page 30
Wheels
Page 30
Adjust Quick Release
Page 31
Rear Wheel Installation
Page 31
Removing Rear Wheel
Page 33
Front Wheel Secondary Retention Devices
Page 33
Front Wheel Installation
Page 34
Removing Front Wheel
Page 35
Hand Brake
Page 36
Unfold Stroller
Page 37
Fold Stroller
USING Stroller for jogging off-road mode
Page 37
STROLLER ADJUSTMENTS
Page 39
Page 40
Check Tire Pressure
Page 40
Adjust Tracking
Page 40
Fine Tune Tracking
Page 41
Select Shock Setting
Page 42
Setting Parking Brake
Page 42
Secure Child In Seat
Page 43
Attach Wrist Strap
Page 44
Recline Seat
Page 44
Position Canopy
Page 45
Accessory Adapter
Page 45
WEATHER SHIELD
Page 45
CARE AND MAINTENANCE
Page 46
STORAGE
Page 47
CARGO
Page 47
STROLLER ACCESSORIES
Page 47
LIMITED WARRANTY
Page 47
28
STROLLER ANATOMY
SPORT UTILITY STROLLER DUALLIE, IRONMAN DUALLIE
Hand Brake Lever
Handlebar
Canopy
Handlebar
Release Lever
Seat Harness
Shock Release
Knob
Swing Arm
Fender
Quick Release
Lever
Brake Caliper
Assembly
Low Boy
Cargo Basket
Wrist Strap
Seat Back Pocket
CONGRATULATIONS
Congratulations on your purchase
of the BOB Sport Utility Stroller
®
®
Duallie or IRONMAN Duallie
Stroller.
For updates to this manual,
warranty and other recent product
notifications, please visit www.
bobgear.eu periodically or any
time before making approved
changes or adding approved
equipment to your stroller.
Frame Release
Handle
Seat Retention
Strap
Parking Brake
Quick Release
Lever
29
AGE RECOMMENDATIONS
Your child should be at least 6
months old before riding in a BOB
Duallie® stroller. For jogging/off-road
stroller use, children should be at
least 9 months old. This pushchair is
designed for children up to 3 years or
maximum 17 kg weight.
FENDER INSTALLATION
Before installing the front wheel, you
will need to attach the fender.
1. Remove Mounting Screws
Two fender mounting screws can be
found already installed in the stroller
frame. Remove the two fender
mounting screws.
Children develop at different rates.
Prior to first use, consult with your
pediatrician regarding suitability of
stroller use with your child.
Please refer to the below table for
age/use guidelines:
RECOMMENDED
USE
AGE
Walk Only
6 Months - 3 Years
or 17 kg weight per
occupant
Jogging/Off-Road
9 Months - 3 Years
or 17 kg weight per
occupant
When using the stroller in jogging/
off-road mode, make sure to follow
the section USING STROLLER for
jogging/off-road.
STROLLER ASSEMBLY
UNPACK STROLLER
Remove stroller and wheels from box.
Front wheel is stowed in folded stroller.
NOTE: You might want to remove
a fabric screw (right or left) to give
better access to the cross tube
mounting hole.
2. Align Fender And Cross Tube Hole
Align the hole in the metal tab of the
fender with the threaded hole in the
center of the front cross tube and
install screw.
3. Align Fender And Brake
Mounting Hole
Align the hole in the plastic fender
with the hole in the brake mounting
plate and install screw.
4. Tighten Screws
Center fender on stroller and tighten
screws. Reinstall and tighten any
additional fabric screws that had
been removed.
Remove all packaging materials
and discard to avoid choking and
suffocation hazards.
30
WHEELS
ADJUST QUICK RELEASE
Before attempting to install wheels,
read and understand warnings and
instructions completely.
The rear wheels are correctly
clamped in place by the force
generated when the quick release
lever is closed and the cam action
pulls the axle against the dropout,
securing it in place.
Using your stroller with an
improperly adjusted wheel quick
release can allow the wheel to
vibrate, wobble or become
detached from the stroller.
Accordingly, it is critical that you:
• Ask your dealer to instruct you
on the proper technique for
safely installing and removing
your wheels.
The front wheel is correctly clamped
in place by the force generated when
the quick release lever is closed
and the cam action pulls the lever
housing against one dropout, and
pulls the adjusting nut against the
other dropout, clamping the hub
between the dropouts.
•
Understand and use the proper
method for securely clamping
a wheel to the stroller using a
quick release.
•
Check to make sure the wheels
are securely clamped before
each use of the stroller.
The wheel quick release is a cam
device that supplies the clamping
force required to hold the stroller
wheel securely in place. To safely
secure a wheel to the stroller, it is
critical that you understand how
the quick release works, how to
use and adjust it properly and the
amount of force necessary to safely
secure the wheel.
The quick release is a cam device
and must be used correctly to
supply the necessary clamping
force to safely hold the wheel in
place. It is not a wing nut system
and turning the lever while holding
the tension adjusting nut does not
supply the required force to
safely clamp the wheel in the
dropouts.
The tension adjusting nut sets
the amount of clamping force.
Turning the tension adjusting nut
in the clockwise direction while
preventing the quick release lever
from rotating, increases the amount
of clamping force. Alternatively,
turning the tension adjusting nut
counterclockwise, while preventing
the quick release lever from rotating,
reduces the amount of clamping
force. The tension adjusting nut only
needs minor adjustments to provide
the correct clamping force, less than
a half turn can mean the difference
between safe and unsafe clamping
force.
REAR WHEEL INSTALLATION
1. Unlock Parking Brake
Prior to installing the rear wheels,
position the parking brake in the
unlocked position.
31
2. Rotate Quick Release Lever
Rotate the quick release lever so it
curves away from the dropout.
FULLY CLOSED
Tension Adjusting Nut
Quick Release
Lever
3. Insert Rear Wheel Stub Axle
Insert the rear wheel’s stub axle into
the hole in the rear dropout. If the
axle does not slide in easily, loosen
the quick release tension adjusting
nut by hand. Re-insert the axle fully
into the rear dropout until the axle
shoulder or snap ring on the axle
comes in contact with the dropout.
To properly close the quick release
and secure the rear wheel in the
dropouts, confirm the axle is fully
inserted in the dropout, while
maintaining the wheel in this
position, rotate the quick release
toward stroller and into the FULLY
CLOSED position.
When properly closed, the curve of
the quick release will be pointing
toward the dropout and angled
slightly toward the center of the
stroller. To generate enough
clamping force it is necessary to wrap
your fingers around the dropout
while closing the quick release lever.
The proper force required to close
the quick release lever should leave
a visible imprint in the palm of your
hand.
Stub Axle
Dropout
4. Adjust Quick Release Cam Lever
To adjust the quick release, hold the
quick release cam lever in the FULLY
OPEN position with your right hand,
and tighten the tension adjusting nut
with your left hand until it is finger
tight against the dropout.
To TIGHTEN tension adjusting nut,
turn clockwise.
It takes considerable force to
securely clamp the wheel. If you
are able to completely close the
quick release without wrapping
your fingers around the dropout
and the quick release lever does
not leave a visible imprint in the
palm of your hand, the tension is
not adequate. Rotate the lever to
the FULLY OPEN position and turn
the tension adjusting nut a quarter
turn clockwise and repeat the
closing process.
32
If the quick release lever cannot be
rotated to the FULLY CLOSED
position, rotate the lever to the
FULLY OPEN position and turn the
tension adjusting nut a quarter
turn counterclockwise. Repeat the
closing process.
To LOOSEN tension adjusting nut,
turn counterclockwise.
FULLY CLOSED
FRONT WHEEL SECONDARY
RETENTION DEVICES
Your stroller fork utilizes secondary
wheel retention devices designed to
help keep the wheel from
disengaging from the fork if the quick
release is incorrectly adjusted and
tightened. The wheel can still remain
loose and wobbly even with the
secondary retention device working if
the quick release has not been
properly tightened and adjusted. The
secondary retention devices on your
stroller are the integral type that are
formed into the outer faces of the
fork dropouts.
REMOVING REAR WHEEL
1. Unlock Parking Brake
Prior to removing the rear wheels,
position the parking brake in the
unlocked position.
2. Open Quick Release Lever
Move the wheel’s quick release lever
from the locked or FULLY CLOSED
position to the FULLY OPEN position.
FULLY CLOSED
FULLY OPEN
3. Remove Wheel
Raise the wheel a few centimeters off
the ground and pull the wheel out of
the dropout.
Dropouts
(Secondary Retention Devices)
It is critical that you do not remove
or disable the secondary retention
devices. The secondary retention
devices serve as a backup for a
critical adjustment. The secondary
retention devices can reduce the
risk of the wheel disengaging from
the fork if the quick release is not
adjusted and tightened correctly.
Removing or disabling the
secondary retention devices will
void the warranty.
Secondary retention devices are
not a substitute for correct quick
release adjustment and tightening.
Using your stroller with an
33
Make a periodical routine check
of adequate wheel fixing and
clamping. If the wheel is not fully
engaged and slightly moves to the
outside the wheel has to be fixated
instantly.
FRONT WHEEL INSTALLATION
1. Install Front Wheel Quick Release Lever
Remove Tension Adjusting Nut
from quick release rod and take
off first spring. Slide quick release
rod through front wheel axle, place
spring back on quick release rod,
small side toward axle, and thread
tension adjusting nut back on.
3. Rotate Front Wheel Quick
Release Lever
Rotate quick release lever so that it
curves away from the wheel. This
places it in the FULLY OPEN position.
Quick Release Lever
FULLY OPEN
FULLY CLOSED
O P EN
improperly adjusted and tightened
wheel quick release can allow
the wheel to vibrate, wobble or
become detached from the stroller.
4. Insert Front Wheel
When facing the front of the stroller,
insert the wheel between the fork
dropouts so that the axle firmly
contacts the top of the slots of the
fork dropouts.
Tension Adjusting Nut
Dropout
Spring
Quick Release
Rod
NOTE: Prior to installing the front
wheel it is necessary to open the
brake quick release to provide clearance for the wheel/tire to pass the
brake pads.
2. Open Brake Quick Release
Open the brake quick release by
rotating the brake quick release lever
in the clockwise direction.
Brake Quick Release
OPEN
5. Adjust Quick Release Lever
To adjust the quick release, hold the
quick release cam lever in the FULLY
OPEN position with your right hand
as shown. Tighten the tension adjusting nut with your left hand until it is
finger tight against the fork dropout.
Tension Adjusting Nut
Quick Release Lever
6. Close Quick Release Lever
To properly close the quick release
and secure the front wheel in
the dropouts, confirm the axle is
34
contacting the top of the dropouts
on both sides and the wheel is
centered left to right.
Fork Blade
FULLY CLOSED
Dropouts
FULLY OPEN
While maintaining the wheel in this
position, rotate the quick release
upward and into the FULLY CLOSED
position. When properly closed,
the curve of the quick release will
be pointing toward the wheel
and parallel to the fork blade. To
generate enough clamping force
it is necessary to wrap your fingers
around the fork blade while closing
the quick release lever. The proper
force required to close the quick
release lever should leave a visible
imprint in the palm of your hand.
It takes
considerable force to securely
clamp the wheel. If you are able to
completely close the quick release
without wrapping your fingers
around the fork blade and the
quick release lever does not leave
a visible imprint in the palm of your
hand, the tension is not adequate.
Rotate the lever to the FULLY
OPEN position and turn the
tension adjusting nut a quarter
turn clockwise and repeat the
closing process.
7. Close Brake Quick Release
After installing the front wheel, the
brake quick release will need to be
placed in the closed position. Close
the brake quick release lever by
squeezing the brake pads against
the wheel with one hand, then rotate
the brake quick release lever in the
counter clockwise direction with your
other hand until it points downward.
Brake Quick Release
CLOSED
REMOVING FRONT WHEEL
1. Open Brake Quick Release
See Front Wheel Installation section.
2. Open Quick Release Lever
Move the wheel’s quick release lever
from the locked or FULLY CLOSED
position to the FULLY OPEN position.
Your front fork has integral secondary
retention devices that require loosening the tension adjusting nut enough
to allow removal of the wheel.
3. Remove Front Wheel
Raise the front wheel a few centimeters off the ground and tap the top of
the wheel with the palm of your hand
to knock the wheel out of the front
fork.
If the quick release lever cannot
be rotated to the FULLY CLOSED
position, rotate the lever to the
FULLY OPEN position and turn the
tension adjusting nut a quarter
turn counterclockwise. Repeat the
closing process.
35
HAND BRAKE
HAND BRAKE
1. Align Brake Pads
If brakes are misaligned, use a 10mm
wrench to loosen brake pad nuts,
slide pads into correct position and
tighten securely.
CL
OS
E
Brake Caliper
Brake Pad Aligned With Rim
2. Adjust Cable Tension
The cable tension is pre-adjusted at
the factory, but the brake cable will
need periodic adjustment (as the
cable stretches slightly and the black
cable housing compresses over time).
To adjust cable tension, there are two
barrel adjusters in the brake system;
one at the hand brake lever, and one at
the caliper brake. To adjust the brake
cable tension, one or both barrel adjusters may need to be adjusted.
Hand Brake Lever
Handlebar
CALIPER BRAKE
Brake Caliper
Mounting Nut
Barrel Adjuster
Lock Ring
CL
OS
E
The hand brake may be used to help
slow or stop a stroller. The hand
brake is not a parking brake.
NOTE: For the hand brake to work
correctly, it is critical that it be
adjusted properly. Squeeze the brake
lever and verify that the brake pads
contact the rim. Verify brake quick
release is in closed position. See
Front Wheel Installation section.
The hand brake system is equipped
with two barrel adjusters. If you are
not familiar with how to use the
barrel adjusters, please contact BOB
customer service or visit your local
dealer for assistance.
Brake Caliper
To tighten the cable, loosen the lock
ring and turn the barrel adjuster
in the counter clockwise direction.
Secure the barrel adjuster in the new
position by tightening the lock ring
against the caliper or brake lever
body.
To loosen the cable, turn the barrel
adjuster in a clockwise direction and
secure by tightening the lock ring.
There should be a 1 mm clearance
between the rim and brake pads.
3. Reposition Brake Caliper
If gap is not equal on each brake
pad, the brake caliper can easily be
repositioned on the frame by
loosening the caliper mounting nut
with a 10mm wrench, adjust caliper
position and re-tighten the same nut.
Brake Pad
36
If you do not
understand these instructions, or
feel the brake is adjusted
incorrectly, take the stroller to your
dealer for proper adjustment. If
your brake pads are worn, see your
dealer for replacements.
SNAP
UNFOLD STROLLER
Care must be taken when folding
and unfolding the stroller to
prevent finger entrapment or
injury.
2. Rotate Handlebar
Lift handlebar up and back until it
“snaps” into locked and upright
position.
To avoid injuries, never fold or
unfold stroller with other
individuals within reach of stroller.
Ensure that all the locking devices
are engaged before use.
SNAP
1. Lift Red Frame Release Handle
Keep tires on ground as stroller swing
arm begins to swing open.
NOTE: Stroller swing arm will swing
open and “snap” into an open and
locked position.
37
3. Attach Seat Retention Strap
Loop seat retention strap around cross
tube and secure with buckle.
Do not loop seat
retention strap around or over brake
bar.
Seat retention strap
must be correctly attached before
loading stroller.
Correctly Attached Seat Retention Strap
FOLD STROLLER
1. Lock Parking Brake
Set parking brake in locked position.
2. Remove Child From Seat
3. Empty Stroller
Remove contents from low boy cargo
basket and pockets.
4. Rotate Handlebar
Squeeze both handlebar release levers
simultaneously. Rotate handlebar
forward onto seat.
38
7. Secure Folded Stroller
Use wrist strap buckle to secure
stroller in folded position.
Handlebar
5. Lift Red Frame Release Handle
Using a short, quick tug, lift red frame
release handle up. Keep tires on
ground as stroller collapses toward
front wheel.
8. Make It Smaller
Take off the front and rear wheels to
make it even smaller. See Removing
Rear Wheel and Removing Front
Wheel sections.
USING STROLLER FOR JOGGING
OFF-ROAD MODE
Please make sure to follow the
instructions below when using your
BOB stroller for running/jogging or in
off-road mode:
6. Lay Stroller Flat
Never use any attachments when
using the stroller for jogging or
off-road.
Using the stroller in jogging/offroad mode for children under 9
months of age which cannot sit
upright on their own can be a
serious health hazard and may
impact their physical development.
39
Always go jogging/off-road with
the stroller seat in the fully upright
position. Going jogging/off-road
with the seat in reclined positions
may result in a loss of stability and
injury.
STROLLER ADJUSTMENTS
CHECK TIRE PRESSURE
Plastic wheels are rated to a
maximum tire inflation pressure of 2
bar. The maximum inflation pressure
is embossed on the wheel next to the
valve stem.
Inflating tires above 2 bar can
damage the wheel and/ or tire
resulting in loss of control and
injury.
Aluminum wheels can have the tires
inflated to the pressure embossed on
the tire. However, we recommend 2
bar for a comfortable ride.
Inflating tires above the maximum
inflation pressure embossed on the
tire can damage rim and or tire
resulting in loss of control
and injury.
ADJUST TRACKING
If stroller pulls left or right when the
stroller is on flat terrain, adjust the
tracking as outlined in the following
steps.
Do not roll test
with a child or any occupant in the
stroller.
1. Empty Stroller
Remove contents from low boy cargo
basket and pockets.
2. Check Tire Pressure
3. Place Stroller On Level Ground
Find a stretch of level ground about 5
metres long.
5m
4. Align Rear Wheel Axles
Align stroller so rear wheel axles are
perpendicular to a straight line.
5. Test Alignment
Push stroller straight forward and
release to see if stroller veers right or
left. Repeat push test several times.
NOTE: If stroller consistently pulls to
left or right, the tracking can often
be corrected by simply rotating the
front wheel axle and/or reorienting
the front wheel by removing the
front wheel, flipping it around and
reinstalling it.
6. Rotate The Front Wheel Axle
Open the front wheel quick release
and rotate axle 90 degrees in
dropout. Retighten quick release.
See Removing Front Wheel and
Front Wheel Installation sections.
40
Tracking Knobs
Rotate Axle 90°
7. Perform Roll Testing
If the stroller still consistently pulls
to the left or right when pushed
straight, proceed to next step.
8. Reorient The Front Wheel
Open the front wheel and front brake
quick releases. Remove the front
wheel and flip it around so the quick
release lever is on the opposite side.
Reinstall the front wheel, secure the
wheel and brake quick release levers.
See Removing Front Wheel and
Front Wheel Installation sections.
If Stroller Pulls RIGHT
1. Open Quick Release Lever
Open quick release lever on front
wheel. It is not necessary to remove
the front wheel. See Removing Front
Wheel section.
2. Adjust RIGHT Tracking Knob
Turn the RIGHT tracking knob
clockwise one full turn thereby
pushing the right side of the wheel
forward and retighten quick release.
See Front Wheel Installation section.
RIGHT Knob
Wheel Reoriented With Quick
Release Lever On Opposite Side
9. Perform Roll Test
If the stroller still consistently pulls
to the left or right when pushed
straight, proceed to Fine Tune Tracking section.
FINE TUNE TRACKING
For fine tune tracking of stroller the
tracking knobs must be used.
3. Perform Roll Test
Repeat Roll test. If stroller still pulls
to the right, repeat steps 1 and 2.
If Stroller Pulls LEFT
1. Open Quick Release Lever
Open quick release lever on front
wheel. It is not necessary to remove
the front wheel. See Removing Front
Wheel section.
2. Adjust LEFT Knob
Turn the left knob clockwise one full
turn thereby pushing the left side
of the wheel forward. Retighten
quick release. See Front Wheel
Installation.
41
Position 2: HARDER
LEFT Knob
3. Repeat Roll Test
If stroller still pulls to the left, repeat
steps 1 and 2.
SELECT SHOCK SETTING
1. Remove Children From Seats
2. Set Shock Setting To Position 2
Depress shock release knob and
simultaneously pull toward back of
stroller, sliding knob into position 2.
Knob will “snap” into place when in
correct position.
REPEAT on opposite side.
CLICK
NOTE: Every time stroller is folded,
stroller shocks default SOFTER position.
SETTING PARKING BRAKE
The parking brake prevents the
stroller from moving while loading
and unloading. The parking brake is
not designed as a stopping brake.
The parking brake is not designed
as a stopping brake. The brake
should not be used to slow or stop
the stroller because doing so could
cause the stroller to stop abruptly,
resulting in loss of control.
Do not park on inclines. The
parking brake is intended to park
the stroller on flat surfaces only.
Parking on inclines may result in tip
over or runaway stroller.
Position 1: SOFTER
To set the parking brake, press the
brake bar down into the locked
position with your foot on the red foot
pedal – making sure the locking pin
fully engages the locking disk.
LOCKED POSITION
CLICK
42
To ensure the brake is set properly,
attempt to roll the stroller fore and
aft after setting the brake. If the
stroller will not roll, the brake is set
properly.
2. Place Child In Seat
Slip one shoulder strap over each
shoulder. Position crotch strap
between legs.
To release the parking brake, lift up
on the red foot pedal with your foot
until the brake bar springs up into
the fully unlocked position.
UNLOCKED POSITION
Shoulder Strap
Crotch Strap
SECURE
CHILD IN SEAT
click!
This vehicle is intended for up to 2
children from 6 months and up to
17 kg weight per occupant. Do not
exceed the maximum weight, as
stroller will become unstable.
Avoid serious injury from falling or
sliding out. Always use seat
harness.
Always use the crotch strap in
combination with the waist belt.
3. Fasten Shoulder Straps
Insert both shoulder strap buckles
into crotch strap buckle.
NOTE: Crotch strap should be
adjusted to have a snug fit.
Crotch Strap Buckle
4. Adjust Shoulder Strap Height
Adjust height of shoulder strap to fit
just above child shoulder height.
Never leave your child in the
stroller unattended with or without
the parking brake set.
1. Set Parking Brake
Rotate parking brake bar down into
locked position.
NOTE: Rear wheels should not rotate
when parking brake is set.
5. Adjust Shoulder Straps
Open Velcro pads. Slide buckle up or
down to adjust straps. Seat harness
should fit snug and be comfortable.
43
RECLINE SEAT
Set parking brake before making
any seat adjustments.
Hold the backrest securely while
you adjust the stroller seat.
6. Tighten Lap Straps
Adjust lap straps to fit snug and be
comfortable.
1. Recline Seat
Pull up on seat recline buckle to
loosen recline straps.
Seat Recline
Buckle
Lap Strap
ATTACH WRIST STRAP
The wrist strap is designed to help
prevent the stroller from rolling away
should you lose your grip on the
stroller. When using the stroller, make
sure the strap is securely looped over
your wrist.
Failure to attach wrist strap can
result in damage or injury.
Seat Recline
Strap
2. Return To Upright Position
To raise seat, lift seat back with one
hand and pull recline strap down with
other hand.
REPEAT on opposite side.
Secure Wrist Strap
Slip loop of strap securely onto wrist.
44
2. Retract Canopy
Push canopy toward handlebar.
When seat/seats is/are fully
reclined, backward tip over is more
likely to occur and may result in an
accident or injury, as seat/seats
and/or passenger may contact
ground before handlebar.
Always go Jogging/Off-Road with
the stroller seat in the fully upright
position. Going Jogging/Off-Road
with the seat/seats in reclined
positions may result in a loss of
stability and injury.
ACCESSORY ADAPTER
This BOB stroller is equipped with
an accessory adapter providing
easy attachment for BOB Stroller
accessories.
TENSION STRAP
Centre Tension Strap provides
support for the centre of the seats
and positions the Centre Mount for
the canopies. It comes pre-adjusted
from the factory; however it can also
be tightened if necessary. Tighten
this strap to keep the seats from
leaning toward each other.
POSITION CANOPY
1. Extend Canopy
Rotate canopy away from
handlebar for additional shade.
Attaching BOB accessories is simple
and easy with this push button, lock
and release design. See Stroller
Accessories section of this manual
for more information on all available
accessories.
WEATHER SHIELD
The Weather Shield is available as an
accessory and not included in your
box.
When using the Weather Shield,
rear flap must be positioned
accordingly to ensure proper air
flow to children.
1. Adjust Seat Position
Pull seat recline straps to raise seats
back into upright position.
45
2. Stow Window Cover
Stow window cover in pocket to
expose canopy straps.
After installing Weather Shield,
confirm vents on Weather Shield are
aligned with space above seat back
and all other vents are free of
obstruction. C
CARE AND MAINTENANCE
ARN MAINTENANCE
3. Pull Canopy Straps
Pull canopy straps and secure to
Velcro strips on back of canopy.
4. Store Canopy
Position rear canopy stay against
handlebar and fold canopy flap up
and over canopy, connecting Velcro
strips. Inspect opening at back of
stroller to make sure space between
top of seat back and canopy is
unobstructed.
Check tire pressure before every
use.
CLEANING
The fabric has a stain resistant
treatment that makes most cleanups
easy. Use a sponge with a solution of
mild soap and cold water (maximum
temperature of 100 deg. F / 38 deg.
C). Rinse thoroughly with clean water
to remove soap then air dry. Do not
use detergent.
REGULAR INSPECTIONS
We recommend inspecting your
stroller before every use. Verify
tire pressure. Verify all screws,
attachment points and fasteners are
tight. Check all wheels to be sure
they are securely clamped. Check for
tears or excessive wear in the fabric.
We recommend you take your stroller
to a designated BOB dealer for
periodic inspection and service.
46
STORAGE
It is best to store your stroller indoors
when it is not in use. This will prolong
its attractive appearance. Extended
exposure to the sun’s ultraviolet rays
can fade and damage the fabric,
tires, and plastic parts.
CARGO
The stroller is equipped with four
small seat pockets for your children,
2 seat back pockets and a low boy
cargo basket under the stroller.
Adding weight to the seat back
changes the center of gravity of
the stroller, and increases the
possibility that it will tip over
backwards, resulting in injury. For
this reason, loads in the seat back
pocket should never exceed 1 kg
and maximum weight capacity for
low boy cargo basket is 4 kg.
Although the seat backs are padded,
it is important to remember that this
is what your child leans against.
Do not place sharp objects in the
seat back pockets. Leaning against
sharp objects in the seat back
pockets can result in injury to
occupants.
STROLLER ACCESSORIES
BOB offers a complete line of
accessories for your Revolution
stroller. Visit our website for full
details.
Add warmth and comfort to your
children’s stroll. The warm & fuzzy
cosytoes insert is a padded fleece
seat liner that inserts into any BOB
Stroller seat.
WEATHER SHIELD
The Weather Shield’s water resistant
design helps to protect your child
from rain and wind while still allowing
a view of the world. Please see page
19 for the usage.
SUN SHIELD
The Sun Shield’s specially designed
mesh screen reduces the sun’s
harmful ultraviolet UVA/UVB rays and
helps to provide a barrier to wind
and flying insects.
SNACK TRAY
The Snack Tray easily inserts into
any BOB Stroller utilizing the BOB
Accessory Adapter feature, placing
snacks and sippy cups at your child’s
fingertips. Folds with stroller.
LIMITED WARRANTY
For this stroller, we provide a
warranty for manufacturing or
material defects for 2 years. The
warranty period begins on the date
of purchase. Please keep the receipt
as proof of purchase.
For complaints please return the
stroller with the receipt. The warranty
is limited to strollers that have been
properly handled and are returned in
a clean and proper condition.
The warranty does not cover:
• natural wear and tear and damage
due to excessive stress.
• damage caused by unsuitable or
WARM FUZZY COSYTOES
47
improper use.
WARRANTY OR NOT?
Fabrics: All our fabrics meet the
highest requirements in terms of
colour fastness to UV radiation.
However, all substances fade if they
are exposed to UV radiation. This
is not a material defect, but normal
wear and tear for which no warranty
is given.
Buckle: If any problems occur on the
buckle, these are often due to dirt
that can be washed out.
For warranty service, please contact
your dealer immediately. You will be
given advice and assistance. When
processing claims, product-specific
depreciation rates apply. For this
we refer you to the general terms
and conditions displayed at the
dealership.
USE, CARE AND MAINTENANCE:
The stroller must be treated
according to the instructions. We
expressly point out that only original
accessories or spare parts may be
used.
SERIAL NUMBER
Open the stroller. From the back
of stroller, look on the inside of the
right swing arm.
MODEL:
XXXXXXXXXX
OR: 0000000000
MFG: DATE XXXX-XX-XX
XXXXXXXX
Serial Number
Serial Number - Warranty Void if Removed
Copyright © 2013.
BRITAX RÖMER Kindersicherheit
GmbH
www.britax.eu
48
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising