DAPAudio | IMIX-7.2 USB | User manual | DAPAudio IMIX-7.2 USB User manual

DAPAudio IMIX-7.2 USB User manual
MANUAL
ENGLISH
IMIX 7.2 USB
Ordercode: D2353
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
IMIX 7.2 USB
Table of contents
Warning ...............................................................................................................................................................................2
Unpacking Instructions .................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................3
Connection with the mains.........................................................................................................................................4
Return Procedure ..........................................................................................................................................................4
Claims ..............................................................................................................................................................................4
Description of the device .................................................................................................................................................4
Features ..........................................................................................................................................................................4
Overview ........................................................................................................................................................................5
Front ..............................................................................................................................................................................5
Rear ..............................................................................................................................................................................6
Installation ......................................................................................................................................................................6
Functions .............................................................................................................................................................................7
Set Up and Operation .....................................................................................................................................................12
Connection Cables .........................................................................................................................................................12
Maintenance ....................................................................................................................................................................12
Troubleshooting ...............................................................................................................................................................13
Product Specification .....................................................................................................................................................13
Block diagram .................................................................................................................................................................14
Ordercode: D2352
1
IMIX 7.2 USB
Warning
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:

DAP IMIX-7.2 USB

IEC cable 1,5m

User manual
CAUTION!
Keep this device away from rain and moisture!
Safety Instructions
Every person involved with the installation, operation and maintenance of this system has to:


be qualified
follow the instructions of this manual
CAUTION! Be careful with your operations.
With a dangerous voltage you can suffer
a dangerous electric shock when touching the wires!
Before you initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the system.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the system are not subject to
warranty.
This system contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the system.
Ordercode: D2352
2
IMIX 7.2 USB





























Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this system to a dimmerpack.
Do not switch the system on and off in short intervals, as this would reduce the system’s life.
Do not open the device and do not modify the device.
Do not drive the inputs with a signal level bigger, than required to drive the equipment to full output.
Do not plug Mics into the console (or stagebox) while Phantom Power is on. Also mute the monitor /
Pa system when turning Phantom Power on or off. Allow the system to adjust for a couple of seconds,
before setting the input gains.
Only use system indoor, avoid contact with water or other liquids.
Avoid flames and do not put close to flammable liquids or gases.
Always disconnect power from the mains, when system is not used. Only handle the power-cord by
the plug. Never pull out the plug by tugging the power-cord.
Always operate the unit with the AC ground wire connected to the electrical system ground.
Make sure you don’t use the wrong kind of cables or defective cables.
Make sure that the signals into the mixer are balanced, otherwise hum could be created.
Make sure you use DI boxes to balance unbalanced signals; All incoming signals should be clear.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power-cord is never crimped or damaged. Check the system and the powercord from time to time.
Please turn off the power switch, when changing the power cord or signal cable, or select the input
mode switch.
Extreme frequency boosts in connection with a high input signal level may lead to overdriving your
equipment. Should this occur, it is necessary to reduce the input signal level by using the INPUT
control.
To emphasize a frequency range, you don’t necessarily have to move its respective control upward;
try lowering surrounding frequency ranges instead. This way, you avoid causing the next piece of
equipment in your sound path to overdrive. You also preserve valuable dynamic reserve
(“headroom”)
Avoid ground loops! Always be sure to connect the power amps and the mixing console to the
same electrical circuit to ensure the same phase!
If system is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your system. Leave the
system switched off until it has reached room temperature.
If your Dap Audio device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Dap Audio dealer for service.
Repairs, servicing and electric connection must be carried out by a qualified technician.
For replacement use fuses of same type and rating only.
WARRANTY: Till one year after date of purchase.
Operating Determinations
This system is not designed for permanent operation. Consistent operation breaks will ensure that the
system will serve you for a long time without defects.
If this system is operated in any other way, than the one described in this manual, the product may suffer
damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, etc.
You endanger your own safety and the safety of others!
Improper installation can cause serious damage to people and property!
Ordercode: D2352
3
IMIX 7.2 USB
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
L
N
EU Cable
UK Cable
US Cable
BROWN
RED
YELLOW/COPPER
BLUE
BLACK
SILVER
YELLOW/GREEN
GREEN
GREEN
Make sure that the device is always connected properly to the earth!
Pin
FASE
NUL
EARTH
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
1) Your name
2) Your address
3) Your phone number
4) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
Description of the device
Features
The IMIX-7.2 USB is a compact installation mixer with zone control. It has exact the same functionality as
the IMIX-7.2 USB but each input on the IMIX-7.2 USB can be routed to the desired output. This function
makes it possible to control 3 areas with different music, sound level and EQ settings.




Gain settings at backside
Special front input for phone/mp3 devices
Zone control for 3 balanced outputs
2 Mic, 11 Line inputs.
Ordercode: D2352
4
IMIX 7.2 USB
Overview
Front
Low control (mic 1/2)
Input display
High control (mic1/2)
Channel fader (channel 1-5)
Mid control (mic1/2)
VU-meter (master A/B)
Talkover on/off switch
Balance control (master A/B)
Master assign button (all channels)
Master control (master A/B)
Reverb control
Power on/off switch
Mic volume control (mic 1/2)
Monitor volume control
Mic on/off button
Mic 1 balanced input connector
Input selection switch (channel 1/2)
Channel select switch
Channel VU-meter (all channels)
Headphone level control
Low control (channel 1-5)
Aux in unbalanced mini jack input connector
High control (channel 1-5)
Headphone output connector
Mid control (channel 1-5)
Aux in unbalanced RCA input connectors
Input selection switch (channel 3/4)
Phone/line button
Input selection switch (channel 5)
Ordercode: D2352
5
IMIX 7.2 USB
Rear
IEC cable inlet
Channel 1 line input connectors
Trim output control (master A/B)
GND screw
Master A mono/stereo switch
USB 2 input
Master A RCA unbalanced out connector
USB 1 input
Monitor unbalanced out connector
Master B XLR balanced out connector
Record A RCA unbalanced out connector
Master A XLR balanced out connector
Channel 5 line 1 input connectors
Display select switch (all RCA inputs)
Channel 4 line 1/line 2 input connectors
Channel gain control (all RCA inputs)
Channel 3 line 1/line 2 input connectors
Mic 2 combo input connector
Channel 2 line input connectors
Mic 1 combo input connector
Installation
Remove all packing materials from the IMIX-7.2 USB. Check that all foam and plastic padding is removed.
Connect all cables.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Ordercode: D2352
6
IMIX 7.2 USB
Functions
1/2/3. Equalizer section (hi/mid/low)
The microphone channel’s equalizer section allows shaping of the incoming
audio signal. All input channels are fitted with 3-band EQ. The hi (2) and low
(1) shelving controls have their frequencies fixed at 5 KHz and 120 Hz
respectively. The mid (3) range control has a peaking response frequency
at 800 KHz. All 3 bands have up to 12dB cut and boost, with a centre detent
for off. Turning an equalizer control to the right amplifies the frequency
range; turning to the left attenuates the signal. Minor changes to an
equalizer control usually produce the best results. Try to avoid excessive
enhancement of the mid band.
4. Talkover on switch
Use this switch to activate the talkover function.
5. Master assign buttons
Use these 2 switches to assign the channel to the master A, master B output
or both.
6. Reverb control
Use this control to adjust the amount of reverb you wish to add to the
corresponding microphone channel.
7. Mic volume control (Mic 1/2)
Controls the volume of the corresponding microphone channel.
8. Mic on/off button
Use this witch to mute the according microphone channel.
Ordercode: D2352
7
IMIX 7.2 USB
9. Input selection switch (channel 1/2)
With this you are able to assign the line (39/40) input
or the USB (42/43) input to the according channel. If
the line input is selected, the according channel
display (16) shows the text you have assigned to it
with the display select (16) switch. If the USB input is
selected, the channel display (16) shows USB 1 or
USB 2 depending on the channel.
10. Channel VU-meter
This meter is a multi-step LED. The accurate level
indication allows you to monitor the channel level
anytime. If the red LEDs frequently blink or constantly
light, the corresponding channel is likely to enter
clipping and you have to reduce the input’s
amplification using the gain control. Make sure that
the red LEDs light only briefly during dynamic peaks.
11/12/13. Equalizer section (channel 1-5)
The channel equalizer section allows shaping of the
incoming audio signal. All input channels are fitted
with 3-band EQ. The hi (2) and low (1) shelving
controls have their frequencies fixed at 12 KHz and
80 Hz respectively. The mid (3) range control has a
peaking response frequency at 1 KHz. All 3 bands
have up to 12dB cut and boost, with a centre
detent for off. Turning the equalizer control to the
right amplifies the frequency range; turning to the
left attenuates the signal. Minor changes to an
equalizer control usually produce the best results. Try
to avoid excessive enhancement of the mid band.
14. Input selection switch (channel 3/4)
With this you are able to assign two sets of line (37/38) inputs to the according channel. The according
channel display (16) shows the text you have assigned to it with the display select (16) switches.
15. Input selection switch (channel 5)
With this you are able to assign the line (36) input or the aux (26/28) inputs to the according channel. If
the line input is selected, the according channel display (16) shows the text you have assigned to it with
the display select (16) switch. If the aux (26/28) inputs are selected, the channel display (16) shows from
aux.
16. Input display
Shows the text you have assigned to the display using the corresponding display select (46) switch.
17. Channel fader
A logarithmic 50mm fader, which controls the volume of the corresponding channel. The overall volume
is set with the master control.
Ordercode: D2352
8
IMIX 7.2 USB
18. Output signal VU-meter (master A/B)
This meter is a multi-step LED. The accurate level indication allows you
to monitor the output signal level at anytime, and match with other
devices.
19. Balance control
By using the bal(ance) control you can adjust the balance between
the left and the right channel. If you use a mono source (input left
mono) the control works as a pan(orama) control and lets you
change the input signal’s position within the stereo image.
20. Master control (master A/B)
Allows you to adjust the output signal to the master A/B (33,44,45)
outputs.
21. Power on/off switch
Do not supply power before the whole system is set up and
connected properly.
22. Monitor volume control
Allows you to adjust the output signal to the monitor (34) output.
23. Mic 1 input combo connector
Electronically balanced combo-type input for connecting low
impedance microphones. The input has extremely low noise and low
hum. When connecting a microphone make sure that the pin
assignment is correct. Always make sure to read the manual of the
microphone you want to connect. The combo- input is not suitable for
connecting an additional mixing console, FX- unit, etc. You have to
use the line (26,28,36-40) inputs, when connecting this kind of
equipment.
Note: When connecting signal sources, please make sure the corresponding channel faders and the
master faders are at their minimum settings. Otherwise unpleasant plug-in noise can occur.
24. Channel select switch
Allows you to assign a source to your headphone section. You are able to select: mic 1, mic 2, channel 1,
channel 2, channel 3, channel 4, channel 5, master A or master B.
25. Headphones level control
This control allows you to adjust the headphones’ volume.
26. Aux mini jack in connector
Unbalanced stereo mini jack aux input for connecting a line/phones level device. Use the Phone/Line ()
switch to set up this input for connecting either headphone or line level output devices.
27. Headphone out connector
You can connect a pair of headphones with an impedance of 32 - 600 Ohm to the headphones
connector. It is a 6,3mm/ 1/4” TRS socket, wired as Tip=left, Ring=right and sleeve = ground.
Caution: Depending on the type of headphones connected to the Headphones jack, the IMIX-7.2 is
capable of producing high output levels via the phones output. Therefore, make sure to turn the
control all the way to the left (minimum setting) before connecting the headphones. Be aware of the
fact that listening to loud sound pressure levels over a longer period of time leads to hearing damage!
28. Aux RCA in connectors
Unbalanced stereo RCA aux input for connecting a line/phones level device. Use the phone/line (29)
button to set up this input for connecting either headphone or line level output devices.
Ordercode: D2352
9
IMIX 7.2 USB
29. Phone/line button
Use this button to configure both aux (26,28) inputs for either line level or phone level.
When the input level is too low, press the line/phone level switch. When the light is on, the level of the
input signal will be boosted. The phone level adjusts the input sensitivity into the correct level for MP3
players, smartphones or tablets. Now you can playback your MP3 devices directly without signal loss.
30. IEC power inlet
This connector is meant for the connection of the supplied main cord. Connect one end of the power
cord to the connector, the other end to the mains, and then turn on the power (21) switch to operate
the unit.
31. Master trim output
This selector allows you, to trim the output level for the master A/B (44,45) outputs. Range -10 to +10dB.
32. Master A mono/stereo switch
Use this switch if you want to connect a mono amplifier to the master A (45) outputs.
33. Master A RCA unbalanced out connectors
Use these outputs to connect an amplifier with unbalanced inputs.
34. Monitor RCA unbalanced out connectors
Use these outputs to connect an amplifier with unbalanced inputs.
35. Record A RCA unbalanced out connector
Use these to connect a recording device.
36. Channel 5 RCA line input connectors
Use to connect a line level device. You can select either this line input or the aux group with the
corresponding input selection (15) switch on the frontpanel.
37. Channel 4 RCA line input connectors
Use to connect a line level device. You can select one of the two line inputs with the corresponding input
selection (14) switch on the frontpanel.
38. Channel 3 RCA line input connectors
Use to connect a line level device. You can select one of two the Line inputs with the corresponding
input selection (14) switch on the frontpanel.
39. Channel 2 RCA line input connectors
Use the RCA inputs to connect a line level device.
40. Channel 1 RCA line input connectors
Use the RCA inputs to connect a line level device.
Ordercode: D2352
10
IMIX 7.2 USB
41. GND screw
Use to connect the ground wire of your turntable.
42. USB 2 port
This USB port can be used to connect the IMIX-7.2 to your PC/ laptop. The USB port is bidirectional, the
input can be assigned to channel 2 by means of the channel select (9) switch. The output of the USB port
is connected to rec A (35) output. This means that you’re only able record a channel with your software if
the channel is assigned to master A.
43. USB 1 port
This USB port can be used to connect the IMIX-7.2 to your PC/ laptop. The USB port is bidirectional, the
input can be assigned to channel 1 by means of the channel select (9) switch. The output of the USB port
is connected to rec A (35) output. This means that you’re only able record a channel with your software if
the channel is assigned to master A.
44. Master B XLR balanced out connectors
Use these outputs to connect an amplifier with balanced inputs.
45. Master A XLR balanced out connectors
Use these outputs to connect an amplifier with balanced inputs.
46. Display select switch
This switch allows you to setup a text for each RCA input. If the input is selected the text will be displayed
on the input display (17). You are able to assign following text: CD 1, CD 2, TUNER, DVD, TV, BEAMER, PC1,
PC2, DJ, AREA 2, AUX 1, AUX 2.
47. Channel gain control
Channel input level is determined by the gain control. With the gain control you are able to adjust the
line input-sensitivity for an optimal match with the mixer’s internal operation level. The high gain of this
mixer is ideal when dealing with very low input levels.
48. Mic 2 combo input connector
Electronically balanced combo-type input for connecting low impedance microphones. The input has
extremely low noise and low hum. When connecting a microphone make sure that the pin assignment is
correct. Always make sure to read the manual of the microphone you want to connect. The XLR- input is
not suitable for connecting an additional mixing console, FX- unit, etc. You have to use the line (54-58)
inputs, when connecting this kind of equipment.
Note: When connecting signal sources, please make sure the corresponding channel faders and the
master faders are at their minimum settings. Otherwise unpleasant plug-in noise can occur.
49. Mic 1 combo input connector
Depending on what’s most suitable in a given situation, you can use the Combo input at the front or the
rear. Both inputs are wired in parallel so you can even use them to link through.
Note: When connecting signal sources, please make sure the corresponding channel faders and the
master faders are at their minimum settings. Otherwise unpleasant plug-in noise can occur.
Ordercode: D2352
11
IMIX 7.2 USB
Set Up and Operation
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 115V specification product on 230V power, or vice versa.
Connection Cables
Take care of your cables, always holding them by the connectors and avoiding knots and twists when
coiling them: This gives the advantage of increasing their life and reliability. Periodically check your
cables. A great number of problems (faulty contacts, ground hum, discharges, etc.) are caused entirely
by using unsuitable or faulty cables.
Unbalanced
Balanced
For these applications the unit provides 1/4" TRS and XLR connectors to easily interface with most
professional audio devices. Follow the configuration examples below for your particular connection.
Maintenance
The DAP Audio IMIX-7.2 USB requires almost no maintenance. However, you should keep the unit clean.
Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in
liquid. Do not use alcohol or solvents.
Keep connections clean. Disconnect electric power, and then wipe the audio connections with a damp
cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
Ordercode: D2352
12
IMIX 7.2 USB
Troubleshooting
DAP Audio IMIX-7.2 USB
This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps
below in sequence until a solution is found. Once the unit operates properly, do not carry out following
steps.
1.
2.
3.
4.
5.
If the device does not operate properly, unplug the device.
Check power from the wall, all cables, connections, etc.
If all of the above appears to be O.K., plug the unit in again.
If nothing happens after 30 seconds, unplug the device.
Return the device to your DAP Audio dealer.
Product Specification
Input channels:
2 x Microphone, combo XLR/Jack
8 x Line, RCA
2 x audio interface, USB-B chassis
1 x Phone, 3,5mm jack
Output channels:
2 x Master Balanced, XLR/RCA
1 x Record, RCA
1 x Monitor, RCA
1 x Headphones, 6.3mm Jack
Display presets:
USB interfaces:
Channel EQ:
Mic EQ:
Frequency response:
T.H.D.:
Dimensions:
Power supply:
Power consumption:
Weight:
CD 1, CD 2, TUNER, DVD, TV, BEAMER, PC1, PC2, DJ, AREA 2, AUX 1, AUX 2
48 KHz, 16 bit plug & play for windows and MAC
80 Hz, 1 KHz, 12 KHz, -12dB / +12dB
120 Hz, 800 Hz, 5 KHz, -12dB / +12dB
20 Hz – 20 KHz
<0.05%
483 x 256 x 126 mm (WxHxD)
100-240V AC, 50/60Hz
32Watt
5,9 Kg
Design and product specifications are subject to change without prior notice.
Ordercode: D2352
13
IMIX 7.2 USB
Block diagram
Ordercode: D2352
14
©2013 DAP Audio
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising