Brocade Communications Systems | ICX 6650 | Installation guide | Brocade Communications Systems ICX 6650 Installation guide

Brocade Communications Systems ICX 6650 Installation guide
53-1003398-01
30 September 2014
Brocade ICX 6650
Hardware Installation Guide
Supporting FastIron Software Release 08.0.20
© 2014, Brocade Communications Systems, Inc. All Rights Reserved.
Brocade, the B-wing symbol, Brocade Assurance, ADX, AnyIO, DCX, Fabric OS, FastIron, HyperEdge, ICX, MLX, MyBrocade, NetIron,
OpenScript, VCS, VDX, and Vyatta are registered trademarks, and The Effortless Network and the On-Demand Data Center are trademarks
of Brocade Communications Systems, Inc., in the United States and in other countries. Other brands and product names mentioned may be
trademarks of others.
Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any
equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document
at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be
currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in
this document may require an export license from the United States government.
The authors and Brocade Communications Systems, Inc. assume no liability or responsibility to any person or entity with respect to the
accuracy of this document or any loss, cost, liability, or damages arising from the information contained herein or the computer programs that
accompany it.
The product described by this document may contain open source software covered by the GNU General Public License or other open
source license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to
the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd.
Contents
Preface..................................................................................................................................... 7
Document conventions......................................................................................7
Text formatting conventions.................................................................. 7
Command syntax conventions.............................................................. 7
Notes, cautions, and warnings.............................................................. 8
Brocade resources............................................................................................ 9
Contacting Brocade Technical Support.............................................................9
Document feedback........................................................................................ 10
About This Document.............................................................................................................. 11
Supported hardware and software.................................................................. 11
What’s new in this document.......................................................................... 11
Brocade ICX 6650 Overview.................................................................................................... 13
Brocade ICX 6650 features.............................................................................13
Brocade ICX 6650 orderable models.............................................................. 13
Brocade ICX 6650 customizable models........................................................ 14
Views of the Brocade ICX 6650 switch........................................................... 17
Ports on Demand licensing............................................................................. 17
Brocade ICX 6650 slot and Ethernet port numbering..................................... 19
Supported transceivers and cables.................................................................20
Breakout cables.............................................................................................. 21
Installing the Brocade ICX 6650..............................................................................................23
Unpacking the device......................................................................................23
Package contents (ICX6650-32-E-ADV, ICX6650-48-E-ADV, and
ICX6650-56-E-ADV)...................................................................... 23
Package contents (ICX6650-32-ADV)................................................ 23
Installation and safety considerations............................................................. 24
Electrical considerations..................................................................... 24
Environmental considerations............................................................. 24
Location considerations...................................................................... 24
Cabinet considerations........................................................................25
Recommendations for cable management......................................... 25
Installation tasks..............................................................................................25
Installation precautions................................................................................... 26
General precautions............................................................................26
Lifting precautions............................................................................... 27
Power precautions.............................................................................. 27
Installing the device in a rack or cabinet......................................................... 28
2-post rack mount installation............................................................. 28
4-post rack mount installation............................................................. 30
Attaching a PC or terminal.............................................................................. 32
Powering on the system..................................................................................33
Power supplies................................................................................................33
Installing and replacing a power supply unit....................................... 33
Installing an AC power supply.............................................................34
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
3
Installing a DC power supply.............................................................35
Installing an SFP+ transceiver...................................................................... 39
Configuring the Brocade ICX 6650........................................................................................ 41
Assigning permanent passwords.................................................................. 41
Setting passwords.............................................................................41
Recovering from a lost password......................................................42
Configuring IP addresses..............................................................................42
Devices running Layer 2 software.....................................................42
Devices running Layer 3 software.....................................................43
Connecting network devices......................................................................... 46
Connectors........................................................................................46
Connecting a network device to a fiber port......................................46
Testing connectivity.......................................................................................47
Pinging an IP address....................................................................... 47
Tracing a route.................................................................................. 48
Troubleshooting network connections.......................................................... 48
Brocade ICX 6650 Operation.................................................................................................49
LED activity interpretation............................................................................. 49
Brocade ICX 6650 front panel LEDs.............................................................49
Brocade ICX 6650 rear panel LEDs..............................................................50
LED patterns................................................................................................. 51
Brocade ICX 6650 maintenance................................................................... 53
Diagnostic tests and monitoring....................................................................53
Managing the Brocade ICX 6650...........................................................................................55
Managing temperature settings.................................................................... 55
Displaying the temperature............................................................... 55
Displaying syslog messages for temperature................................... 56
Changing the temperature warning level ......................................... 56
Changing the temperature poll time.................................................. 57
Removing MAC address entries................................................................... 57
Displaying Brocade ICX 6650 CPU usage....................................................57
Hardware maintenance schedule................................................................. 58
Replacing a copper or fiber-optic module..................................................... 58
Removing a copper or fiber-optic module......................................... 58
Cabling a fiber-optic module............................................................. 59
Cleaning the fiber-optic connectors...................................................59
FRU removal and replacement procedures.................................................. 60
Replacing a power supply unit...................................................................... 61
Determining the need to replace a power supply..............................62
Time and items required................................................................... 62
Replacing a power supply................................................................. 62
Replacing fan trays....................................................................................... 63
Determining the need to replace a fan assembly..............................63
Time and items required................................................................... 63
Installing or replacing the fan assembly............................................ 63
Brocade ICX 6650 Specifications..........................................................................................67
Weight and physical dimensions...................................................................67
Environmental considerations.......................................................................67
Cooling system and fans...............................................................................68
Power supply specifications.......................................................................... 70
4
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
General specifications for Brocade ICX 6650................................................. 72
Supported media types................................................................................... 72
Pinouts and signaling...................................................................................... 72
Memory specifications.....................................................................................72
Regulatory compliance....................................................................................73
Brocade ICX 6650 Regulatory Statements...............................................................................75
BSMI statement (Taiwan)................................................................................75
Canadian requirements...................................................................................75
China CC statement........................................................................................76
China ROHS................................................................................................... 76
Europe and Australia (CISPR 22 Class A Warning)....................................... 77
FCC warning (US only)................................................................................... 77
Germany......................................................................................................... 77
KCC statement (Republic of Korea)................................................................77
VCCI statement...............................................................................................77
Brocade ICX 6650 Cautions and Danger Notices .....................................................................79
Cautions.......................................................................................................... 79
Danger Notices............................................................................................... 84
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
5
6
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Preface
● Document conventions......................................................................................................7
● Brocade resources............................................................................................................ 9
● Contacting Brocade Technical Support.............................................................................9
● Document feedback........................................................................................................ 10
Document conventions
The document conventions describe text formatting conventions, command syntax conventions, and
important notice formats used in Brocade technical documentation.
Text formatting conventions
Text formatting conventions such as boldface, italic, or Courier font may be used in the flow of the text
to highlight specific words or phrases.
Format
Description
bold text
Identifies command names
Identifies keywords and operands
Identifies the names of user-manipulated GUI elements
Identifies text to enter at the GUI
italic text
Identifies emphasis
Identifies variables and modifiers
Identifies paths and Internet addresses
Identifies document titles
Courier font
Identifies CLI output
Identifies command syntax examples
Command syntax conventions
Bold and italic text identify command syntax components. Delimiters and operators define groupings of
parameters and their logical relationships.
Convention
Description
bold text
Identifies command names, keywords, and command options.
italic text
Identifies a variable.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
7
Notes, cautions, and warnings
Convention
Description
value
In Fibre Channel products, a fixed value provided as input to a command
option is printed in plain text, for example, --show WWN.
[]
Syntax components displayed within square brackets are optional.
Default responses to system prompts are enclosed in square brackets.
{x|y|z}
A choice of required parameters is enclosed in curly brackets separated by
vertical bars. You must select one of the options.
In Fibre Channel products, square brackets may be used instead for this
purpose.
x|y
A vertical bar separates mutually exclusive elements.
<>
Nonprinting characters, for example, passwords, are enclosed in angle
brackets.
...
Repeat the previous element, for example, member[member...].
\
Indicates a “soft” line break in command examples. If a backslash separates
two lines of a command input, enter the entire command at the prompt without
the backslash.
Notes, cautions, and warnings
Notes, cautions, and warning statements may be used in this document. They are listed in the order of
increasing severity of potential hazards.
NOTE
A Note provides a tip, guidance, or advice, emphasizes important information, or provides a reference
to related information.
ATTENTION
An Attention statement indicates a stronger note, for example, to alert you when traffic might be
interrupted or the device might reboot.
CAUTION
A Caution statement alerts you to situations that can be potentially hazardous to you or cause
damage to hardware, firmware, software, or data.
DANGER
A Danger statement indicates conditions or situations that can be potentially lethal or
extremely hazardous to you. Safety labels are also attached directly to products to warn of
these conditions or situations.
8
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade resources
Brocade resources
Visit the Brocade website to locate related documentation for your product and additional Brocade
resources.
You can download additional publications supporting your product at www.brocade.com. Select the
Brocade Products tab to locate your product, then click the Brocade product name or image to open the
individual product page. The user manuals are available in the resources module at the bottom of the
page under the Documentation category.
To get up-to-the-minute information on Brocade products and resources, go to MyBrocade. You can
register at no cost to obtain a user ID and password.
Release notes are available on MyBrocade under Product Downloads.
White papers, online demonstrations, and data sheets are available through the Brocade website.
Contacting Brocade Technical Support
As a Brocade customer, you can contact Brocade Technical Support 24x7 online, by telephone, or by email. Brocade OEM customers contact their OEM/Solutions provider.
Brocade customers
For product support information and the latest information on contacting the Technical Assistance
Center, go to http://www.brocade.com/services-support/index.html.
If you have purchased Brocade product support directly from Brocade, use one of the following methods
to contact the Brocade Technical Assistance Center 24x7.
Online
Telephone
E-mail
Preferred method of contact for nonurgent issues:
Required for Sev 1-Critical and Sev
2-High issues:
support@brocade.com
• My Cases through MyBrocade
•
Continental US: 1-800-752-8061
• Software downloads and licensing •
tools
Europe, Middle East, Africa, and
Asia Pacific: +800-AT FIBREE
(+800 28 34 27 33)
• Knowledge Base
•
For areas unable to access toll
free number: +1-408-333-6061
•
Toll-free numbers are available in
many countries.
Please include:
•
Problem summary
•
Serial number
•
Installation details
•
Environment description
Brocade OEM customers
If you have purchased Brocade product support from a Brocade OEM/Solution Provider, contact your
OEM/Solution Provider for all of your product support needs.
• OEM/Solution Providers are trained and certified by Brocade to support Brocade® products.
• Brocade provides backline support for issues that cannot be resolved by the OEM/Solution Provider.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
9
Document feedback
• Brocade Supplemental Support augments your existing OEM support contract, providing direct
access to Brocade expertise. For more information, contact Brocade or your OEM.
• For questions regarding service levels and response times, contact your OEM/Solution Provider.
Document feedback
To send feedback and report errors in the documentation you can use the feedback form posted with
the document or you can e-mail the documentation team.
Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and
completeness of this document. However, if you find an error or an omission, or you think that a topic
needs further development, we want to hear from you. You can provide feedback in two ways:
• Through the online feedback form in the HTML documents posted on www.brocade.com.
• By sending your feedback to documentation@brocade.com.
Provide the publication title, part number, and as much detail as possible, including the topic heading
and page number if applicable, as well as your suggestions for improvement.
10
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
About This Document
● Supported hardware and software.................................................................................. 11
● What’s new in this document.......................................................................................... 11
Supported hardware and software
This document is specific to the Brocade ICX 6650 running FastIron release 08.0.20.
What’s new in this document
The following table lists the new information added to this guide for FastIron release 08.0.20.
TABLE 1 Summary of enhancements in FastIron release 08.0.20
Feature
Description
Location
No new features have been added to
this release.
Documentation bugs have been
addressed.
Small updates spread throughout the
guide.
Hardware specifications
Documentation bugs have been
addressed.
Pinouts and signaling on page 72
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
11
What’s new in this document
12
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Overview
● Brocade ICX 6650 features.............................................................................................13
● Brocade ICX 6650 orderable models.............................................................................. 13
● Brocade ICX 6650 customizable models........................................................................ 14
● Views of the Brocade ICX 6650 switch........................................................................... 17
● Ports on Demand licensing............................................................................................. 17
● Brocade ICX 6650 slot and Ethernet port numbering..................................................... 19
● Supported transceivers and cables.................................................................................20
● Breakout cables.............................................................................................................. 21
Brocade ICX 6650 features
The Brocade ICX 6650 is an Ethernet switch for campus LAN aggregation and classic Ethernet data
center Top of Rack (ToR) environments.
The Brocade ICX 6650 is a high-density aggregation switch that offers both 1/10 and 10/40 Gigabit
Ethernet (GbE) line rates, low latency cut-through switching, and 1600 Gbps switching capacity for
campus LAN and classic Ethernet data center environments.
The Brocade ICX 6650 features:
• Comprehensive support for a range of 10GbE and 40GbE optics (refer to the Brocade Optics Family
Data Sheet).
• Dual redundant, hot-swappable 250 W AC or 510 W DC power supplies available with intake or
exhaust airflow.
• Dual redundant, hot-swappable fan units available with intake or exhaust airflow.
• One Gigabit Ethernet port (RJ-45) and one serial management port to configure and manage the
switch through the CLI.
Brocade ICX 6650 orderable models
The Brocade ICX 6650 switches consists of these orderable models.
TABLE 2 Brocade ICX 6650 orderable switch models
Model
Description
ICX6650-32-ADV
Brocade ICX 6650 with 32 10 GbE SFP+ ports enabled. No power supplies or fan units
(need to be ordered separately). Advanced software. Optional Ports on Demand (PoD)
licenses to enable up to 56 10 GbE SFP+ ports and 6 QSFP+ ports can be ordered
separately. No optics.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
13
Brocade ICX 6650 customizable models
TABLE 2 Brocade ICX 6650 orderable switch models (Continued)
Model
Description
ICX6650-32-E-ADV
Brocade ICX 6650 with 32 10 GbE SFP+ ports enabled. Includes two 250 W AC power
supplies and two fan units, power-supply-side exhaust (port-side intake) airflow.
Advanced software. No optics.
ICX6650-48-E-ADV
Brocade ICX 6650 with 48 10 GbE SFP+ ports enabled. Includes two 250 W AC power
supplies and two fan units, power-supply-side exhaust (port-side intake) airflow.
Advanced software. No optics.
ICX6650-56-E-ADV
Brocade ICX 6650 with 56 10 GbE SFP+ ports enabled. Includes two 250 W AC power
supplies and two fan units, power-supply-side exhaust (port-side intake) airflow.
Advanced software. No optics.
Brocade ICX 6650 customizable models
After March 2014, you will no longer be able to order the following SKUs:
•
•
•
•
•
•
•
ICX6650-32-I-ADV
ICX6650-40-E-ADV
ICX6650-40-I-ADV
ICX6650-48-I-ADV
ICX6650-56-I-ADV
ICX6650-80-E-ADV
ICX6650-80-I-ADV
However, you can build your own equivalent models by combining the ICX6650-32-ADV SKU with
PoD license, power supply, and fan SKUs. The following table lists the models you can build by
combining these components:
TABLE 3 Brocade ICX 6650 custom models
Model
Description
License, power
supply, and fan
SKUs needed
Quantity
ICX6650-32-I-ADV
Brocade ICX 6650 with 32 10-GbE
SFP+ ports enabled. Includes two
250 W AC power supplies and two
fan units, intake airflow. Advanced
software. No optics.
RPS15-I
2
XICX6650-FAN-I
2
Brocade ICX 6650 with 40 10-GbE
SFP+ ports enabled. Includes two
250 W AC power supplies and two
fan units, exhaust airflow. Advanced
software. No optics.
ICX6650-8P10G-LICPOD
1
RPS15-E
2
XICX6650-FAN-E
2
ICX6650-40-E-ADV
14
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Overview
TABLE 3 Brocade ICX 6650 custom models (Continued)
Model
Description
License, power
supply, and fan
SKUs needed
Quantity
ICX6650-40-I-ADV
Brocade ICX 6650 with 40 10-GbE
SFP+ ports enabled. Includes two
250 W AC power supplies and two
fan units, intake airflow. Advanced
software. No optics.
ICX6650-8P10G-LICPOD
1
RPS15-I
2
XICX6650-FAN-I
2
ICX6650-8P10G-LICPOD
2
RPS15-I
2
XICX6650-FAN-I
2
ICX6650-8P10G-LICPOD
3
RPS15-I
2
XICX6650-FAN-I
2
ICX6650-8P10G-LICPOD
3
ICX6650-2P40G-LICPOD
3
RPS15-E
2
XICX6650-FAN-E
2
ICX6650-8P10G-LICPOD
3
ICX6650-2P40G-LICPOD
2
RPS15-I
2
XICX6650-FAN-I
2
ICX6650-48-I-ADV
ICX6650-56-I-ADV
ICX6650-80-E-ADV
ICX6650-80-I-ADV
Brocade ICX 6650 with 48 10-GbE
SFP+ ports enabled. Includes two
250 W AC power supplies and two
fan units, intake airflow. Advanced
software. No optics.
Brocade ICX 6650 with 56 10-GbE
SFP+ ports enabled. Includes two
250 W AC power supplies and two
fan units, intake airflow. Advanced
software. No optics.
Brocade ICX 6650 with 56 10-GbE
SFP+ and 6 40-GbE ports enabled.
Includes two 250 W AC power
supplies and two fan units, exhaust
airflow. Advanced software. No
optics.
Brocade ICX 6650 with 56 10-GbE
SFP+ and 6 40-GbE ports enabled.
Includes two 250 W AC power
supplies and two fan units, intake
airflow. Advanced software. No
optics.
In addition to the models listed in the previous table, you can create other custom models by making
different SKU combinations as described in the following table.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
15
Brocade ICX 6650 Overview
TABLE 4 SKUs for creating custom Brocade ICX 6650 switch models
16
SKU
Description
ICX6650-8P10G-LIC-POD
Ports on Demand license for Brocade ICX 6650, for
8×10 GbE SFP+ ports.
ICX6650-2P40G-LIC-POD
Ports on Demand license for Brocade ICX 6650, for two
QSFP+ (40 GbE or 4×10 GbE) ports.
RPS15-E
250 W AC power supply; port-side exhaust airflow.
RPS15-I
250 W AC power supply; port-side intake airflow.
RPS16DC-E
510 W DC power supply; power-supply-side exhaust
(port-side intake) airflow.
RPS16DC-I
510 W DC power supply; power-supply-side intake
(port-side exhaust) airflow.
XICX6650-FAN-E
Brocade ICX 6650 fan unit, exhaust airflow.
XICX6650-FAN-I
Brocade ICX 6650 fan unit, intake airflow.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Views of the Brocade ICX 6650 switch
Views of the Brocade ICX 6650 switch
1
2
3
4
5
Push button reset
PSU1 and PSU2 status LEDs
DIAG and MS status LEDs
40 GbE QSFP rear port status/activity
LEDs
10 GbE QSFP-to-SFP breakout port
status/activity LED
6
7
8
9
10
Air intake/exhaust
Ports 1/1 through 1/32
Ports 1/33 through 1/40
Ports 1/41 through 1/48
Ports 1/49 through 1/56
FIGURE 1 Front view of the Brocade ICX 6650
1
2
3
4
5
Fan unit
Mini-USB serial console port
Ports 2/1 through 2/2
Port 2/3
Fan unit
6
7
8
9
10
Power supply
Ethernet management port
Port 2/4
Ports 3/1 through 3/8
Power supply
FIGURE 2 Rear view of the Brocade ICX 6650
Ports on Demand licensing
The Brocade ICX 6650 features Ports on Demand licensing. With Ports on Demand licensing, software
features do not require licenses and you can add port licenses as needed.
A fully populated device supports 56 front-panel, dual-speed 1/10 GbE SFP+ ports, 4 rear-panel 40
GbE QSFP+ ports, and 2 rear-panel 4x10 GbE QSFP+ breakout ports.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
17
Brocade ICX 6650 Overview
You can purchase and install Ports on Demand licenses in blocks of eight dual-speed 1/10 GbE SFP+
on the front-panel ports. These ports are grouped sequentially, enabling ports 33 through 40, 41
through 48, and 49 through 56. To enable the additional front-panel ports, you must purchase and
install an ICX6650-8P10G-LIC-POD license.
1
2
3
Base (32x10 GbE)
8x10 GbE (33-40)
8x10 GbE (41-48)
4
5
8x10 GbE (49-56)
Blocks of 8x10 GbE SFP+ ports
FIGURE 3 Brocade ICX 6650 front-panel ports
You can purchase and install up to three ICX6650-2P40G-LIC-POD licenses to enable pairs of 40
GbE ports or 4x10 GbE breakout ports on the rear panel. An ICX6650-2P40G-LIC-POD license can be
applied to any of the following pairs of 40 GbE rear-panel ports or 4x10 GbE breakout ports:
• 2/1 and 2/2 40 GbE rear-panel ports
• 2/3 and 2/4 40 GbE rear-panel ports
• 3/1-4 and 3/5-8 4x10 GbE rear-panel breakout ports
NOTE
You can add an ICX6650-2P40G-LIC-POD license to any configuration.
1
2
3
2/1-2: Any pair of QSFP+ ports—2x40
GbE ports (2/1-2, 2/3-4), 2 4x10 GbE
ports (3/1-4,3/5-8)
2/4
3/1-8: 4x10 GbE breakout ports (3/1-4,
3/5-8)
FIGURE 4 Brocade ICX 6650 rear-panel ports
The breakout ports support one of the following options:
• Direct-attached QSPF+ to 4 SFP+ copper breakout cables (Part number 40G-QSFP-4SFP-C-/
0101/0301/0501)
• Breakout-capable SR4 QSPF+ optical transceiver (Part number 40G-QSFP-SR4-INT)
No trial licenses are available with Ports on Demand licensing.
18
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 slot and Ethernet port numbering
Brocade ICX 6650 slot and Ethernet port numbering
Many CLI commands require users to enter port numbers as part of the command syntax, and many
show command outputs display port numbers. The port numbers are entered and displayed in stackunit/slot number/port number format. In all Brocade ICX 6650 inputs and outputs, the stack-unit number
is always 1.
The Brocade ICX 6650 contains the following slots and Ethernet ports:
• Slot 1 is located on the front of the Brocade ICX 6650 switch and contains ports 1 through 56, which
are 1/10 GbE SFP+ ports. Refer to the following figure.
1
Slot 1
FIGURE 5 Brocade ICX 6650 front-panel ports
• Slot 2 is located on the rear of the Brocade ICX 6650 switch and contains ports 1 through 3 on the
top row and port 4 on the bottom row. These ports are 40 GbE QSFP+ ports. Refer to the following
figure.
NOTE
The QSFP+ 40 GbE LR4 optical transceiver is supported in ports 1 and 2 only. When the module is
inserted into a stack-unit/slot number/port number combination that is not 1/2/1 or 1/2/2, the following
error message displays: “QSFP LR-4 optics not supported on port port-number.”
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
19
Supported transceivers and cables
1
2
3
Slot 2
Slot 2
Slot 3
FIGURE 6 Brocade ICX 6650 rear-panel ports
• Slot 3 is located on the rear of the Brocade ICX 6650 switch and contains ports 1 through 8. These
ports are 4x10 GbE breakout ports and require the use of a breakout cable. Refer to the previous
figure.
Supported transceivers and cables
The Brocade ICX 6650 supports the following transceivers and cables:
• 1 GbE
‐
SX
‐
LX
‐
Copper
• 10 GbE
‐
SFP+: USR, Short Reach, Long Reach
‐
Active twinaxial copper (1 meter, 3 meter, and 5 meter)
‐
10 GbE ER SFP+
• 40 GbE
‐
‐
‐
‐
‐
Standard 40 GbE (SR4) transceiver without breakout
40 GbE (SR4) QSFP+ transceiver with breakout to 4x10 GbE up to 100 meters on OM3
fiber
40 GbE direct attach (DAC) copper breakout (1 meter, 3 meter, and 5 meter)
40 GbE QSFP to QSFP active twinaxial (1 meter, 3 meter, and 5 meter)
40 GbE (LR4) QSFP+ transceiver up to 10 km
NOTE
Non-branded active twinaxial cables can be used, but Brocade does not support them.
20
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Breakout cables
Breakout cables
The rear panel of the Brocade ICX 6650 contains two 4x10 GbE ports which support the following
cables:
• QSFP+ to 4 SFP+ (4x10 GbE) direct-attach copper breakout cables
• QSFP+ (MTP 1x8 or 1x12) optical breakout cables
FIGURE 7 QSFP+ to 4 SFP+ (4x10 GbE) direct-attach copper breakout cable
FIGURE 8 QSFP+ (MTP 1x8 or 1x12) optical breakout cable
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
21
Breakout cables
22
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Installing the Brocade ICX 6650
● Unpacking the device......................................................................................................23
● Installation and safety considerations............................................................................. 24
● Installation tasks..............................................................................................................25
● Installation precautions................................................................................................... 26
● Installing the device in a rack or cabinet......................................................................... 28
● Attaching a PC or terminal.............................................................................................. 32
● Powering on the system..................................................................................................33
● Power supplies................................................................................................................33
● Installing an SFP+ transceiver........................................................................................ 39
Unpacking the device
The Brocade ICX 6650 ships with all of the items listed below. Verify the contents of your shipping
container. If any items are missing, contact the place of purchase.
Package contents (ICX6650-32-E-ADV, ICX6650-48-E-ADV, and
ICX6650-56-E-ADV)
The following items are included in your shipping carton:
• A Brocade ICX 6650 device
• One accessory kit, containing the following items:
‐
‐
‐
‐
‐
‐
Two power cords
One RJ-45 to DB9F adapter
One RJ-45 crossover cable
One mini-USB (M)-DB9(F) cable
Two mounting ears and screws
Grounding terminal screw
Package contents (ICX6650-32-ADV)
The following items are included in your shipping carton:
• A Brocade ICX 6650 device
• One accessory kit, containing the following items:
‐
One RJ-45 to DB9F adapter
‐
One RJ-45 crossover cable
‐
One mini-USB (M)-DB9(F) cable
‐
Two mounting ears and screws
‐
Grounding terminal screw
• Installed filler panels for the right power supply unit (PSU1) slot and left fan slot.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
23
Installation and safety considerations
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
Installation and safety considerations
You can install the Brocade ICX 6650 in the following ways:
• As a standalone unit on a flat surface.
• In an EIA cabinet using a fixed-rail rack mount kit. The optional fixed-rail rack mount kit can be
ordered from your switch retailer. Both the 24"-28" rack depth kit and the 28"-32" rack depth kit will
work with the Brocade ICX 6650.
• In a 2-post Telco rack using a flush mount rack kit. The optional flush mount rack kit for switches
can be ordered from your switch retailer.
• In a 2-post Telco rack using a mid-mount rack kit. The optional mid-mount rack kit for switches can
be ordered from your switch retailer.
Electrical considerations
To install and operate the switch successfully, ensure compliance with the following requirements:
• The primary outlet is correctly wired, protected by a circuit breaker, and grounded in accordance
with local electrical codes.
• The supply circuit, line fusing, and wire size are adequate, as specified by the electrical rating on
the switch nameplate.
• The power supply standards are met.
Environmental considerations
For successful installation and operation of the switch, ensure that the following environmental
requirements are met:
• Because the Brocade ICX 6650 can be ordered with fans that move air either front to back or back
to front, be sure to orient your switch with the airflow pattern of any other devices in the rack. All
equipment in the rack should force air in the same direction to avoid intake of exhaust air.
• The ambient air temperature does not exceed 40° C (104° F) while the switch is operating.
• Some combinations of intake and exhaust airflows may not be compatible with your environment.
Consult your fan and power supply module FRU kit to determine the correct configuration.
Location considerations
Before installing the device, plan its location and orientation relative to other devices and equipment.
Devices can be mounted in a standard 19-inch equipment rack or on a flat surface.
The site should meet the following requirements:
• Maintain the operating environment as specified in Environmental considerations on page 24.
• Allow a minimum of 3 in. of space between the front and the back of the device and walls or other
obstructions for proper airflow.
24
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Cabinet considerations
• Allow at least 3 in. of space at the front and back of the device for the twisted-pair, fiber-optic, and
power cabling.
• Be accessible for installing, cabling, and maintaining the devices.
• Allow the status LEDs to be clearly visible.
• Allow for twisted-pair cables to be routed away from power lines, fluorescent lighting fixtures, and
other sources of electrical interference, such as radios and transmitters.
• Allow for the unit to be connected to a separate grounded power outlet that provides 100 to 240 VAC,
50 to 60 Hz, is within 2 m (6.6 ft) of each device, and is powered from an independent circuit breaker.
As with any equipment, a filter or surge suppressor is recommended.
Cabinet considerations
For successful installation and operation of the switch in a cabinet, ensure the following cabinet
requirements are met:
• The cabinet must be a standard EIA cabinet.
• The equipment in the cabinet is grounded through a reliable branch circuit connection and maintains
ground at all times. Do not rely on a secondary connection to a branch circuit, such as a power strip.
• Airflow and temperature requirements are met on an ongoing basis, particularly if the switch is
installed in a closed or multicabinet assembly.
• The additional weight of the switch does not exceed the cabinet’s weight limits or unbalance the
cabinet in any way.
• The cabinet is secured to ensure stability in case of unexpected movement, such as an earthquake.
Recommendations for cable management
Cables can be organized and managed in a variety of ways; for example, use cable channels on the
sides of the cabinet or patch panels to reduce the potential for tangling the cables. The following list
provides some recommendations for cable management:
CAUTION
Before plugging a cable into to any port, be sure to discharge the voltage stored on the cable by
touching the electrical contacts to ground surface.
NOTE
You should not use tie wraps with optical cables because they are easily overtightened and can
damage the optic fibers. Velcro-like wraps are recommended.
• Plan for the rack space required for cable management before installing the switch.
• Leave at least 1 m (3.28 ft) of slack for each port cable. This provides room to remove and replace
the switch, allows for inadvertent movement of the rack, and helps prevent the cables from being
bent to less than the minimum bend radius.
• For easier maintenance, label the cables and record the devices to which they are connected.
• Keep LEDs visible by routing port cables and other cables away from the LEDs.
Installation tasks
Perform the following steps to install your device. Details for each of these steps are provided on the
pages indicated.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
25
Installation precautions
TABLE 5 Installation tasks
Task number Task
Where to find more information
1
Ensure that the physical environment that will host the
device has the proper cabling and ventilation.
Environmental considerations on
page 24
2
If customizing the ICX6650-32-ADV baseline chassis:
Installing and replacing a power
supply unit on page 33
1. Install at least one power supply unit.
2. Install at least one fan.
3. Obtain and install a PoD license, as described in the
FastIron Ethernet Switch Administration Guide.
Installing or replacing the fan
assembly on page 63
3
Install the device in an equipment rack.
Installing the device in a rack or
cabinet on page 28
4
Attach a terminal or PC to the device. This will enable you to
configure the device through the command line interface
(CLI).
Attaching a PC or terminal on page
32
5
Plug the device into a nearby power source that adheres to
the regulatory requirements outlined in this manual.
Powering on the system on page
33
6
Assign a password for additional access security. No default
password is assigned to the CLI.
Assigning permanent passwords
on page 41
7
Before attaching equipment to the device, you must
configure an interface IP address to the subnet on which the
device will be located. Initial IP address configuration is
performed using the CLI with a direct serial connection.
Subsequent IP address configuration can be performed
using the Web management interface.
Configuring IP addresses on page
42
8
Test IP connectivity to other devices by pinging them and
tracing routes.
Testing connectivity on page 47
9
Continue configuring the device using the CLI or the Web
management interface.
FastIron Ethernet Switch
Administration Guide
10
Secure access to the device.
FastIron Ethernet Switch
Administration Guide
Installation precautions
Follow all precautions when installing a device.
General precautions
DANGER
All fiber-optic interfaces use Class 1 lasers.
26
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Lifting precautions
CAUTION
Do not install the device in an environment where the operating ambient temperature might
exceed 40°C (104°F).
CAUTION
Make sure the airflow around the front, sides, and back of the device is not restricted.
CAUTION
Never leave tools inside the chassis.
Lifting precautions
DANGER
Make sure the rack housing the device is adequately secured to prevent it from becoming
unstable or falling over.
Power precautions
CAUTION
Use a separate branch circuit for each power cord, which provides redundancy in case one of
the circuits fails.
DANGER
To avoid high voltage shock, do not open the device while the power is on.
CAUTION
Ensure that the device does not overload the power circuits, wiring, and over-current protection.
To determine the possibility of overloading the supply circuits, add the ampere (amp) ratings of
all devices installed on the same circuit as the device. Compare this total with the rating limit for
the circuit. The maximum ampere ratings are usually printed on the devices near the input
power connectors.
DANGER
Disconnect the power cord from all power sources to completely remove power from the device.
CAUTION
Before plugging a cable into to any port, be sure to discharge the voltage stored on the cable by
touching the electrical contacts to ground surface.
DANGER
If the installation requires a different power cord than the one supplied with the device, make
sure you use a power cord displaying the mark of the safety agency that defines the regulations
for power cords in your country. The mark is your assurance that the power cord can be used
safely with the device.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
27
Installing the device in a rack or cabinet
Installing the device in a rack or cabinet
DANGER
Make sure the rack housing the device is adequately secured to prevent it from becoming
unstable or falling over.
NOTE
You need a #2 Phillips screwdriver for installation.
Before mounting the switch in a rack, pay particular attention to the following factors:
• Temperature: Because the temperature within a rack assembly may be higher than the ambient
room temperature, check that the rack-environment temperature is within the specified operating
temperature range.
• Mechanical loading: Do not place any equipment on top of a rack-mounted unit.
• Circuit overloading: Be sure that the supply circuit to the rack assembly is not overloaded.
• Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be
given to supply connections other than direct connections to the mains.
2-post rack mount installation
NOTE
The Brocade ICX 6650 is shipped with a 2-post rack mount kit to mount the switch into 2-post Telco
style racks only. If the Brocade ICX 6650 is to be installed into a standard 4-post rack, make sure that
you use the correct rack mount kit.
Use the following procedure when installing the Brocade ICX 6650 in a 2-post rack. For 4-post racks,
follow the procedures in 4-post rack mount installation on page 30.
1. Remove the rack mount kit from the shipping carton. The kit contains the following:
• Two L-shaped mounting brackets.
• Sixteen 8-32 x 5/16 in., panhead Phillips screws with patchlocks.
• Four 10-32 x 5/8 in., panhead Phillips screws (torque to 25 in-lb, 29 cm-kg). Refer to item 1 in the
following figure.
• Eight 32-10 retainer nuts (for square-hole rack rails). Refer to item 2 in the following figure.
• Eight 32-10 retainer nuts (for round-hole rack rails). Refer to item 3 in the following figure.
28
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Installing the Brocade ICX 6650
FIGURE 9 2-post screws and retainer nuts
2. Attach the mounting brackets to the sides of the device using the 8-32 x 5/16 in. screws.
FIGURE 10 Attaching the mounting brackets for a Brocade ICX 6650
3. Position the device in the cabinet, providing temporary support under the switch until the rail kit is
secured to the cabinet.
4. Attach the front right bracket to the rail rack using two 10-32 x 5/8 in. screws and the appropriate
round-hole or square-hole retainer nuts. Refer to the following figure.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
29
4-post rack mount installation
FIGURE 11 Installing the Brocade ICX 6650 in a 2-post rack
5. Repeat step 3 to attach the left front bracket to the left front rack rail and tighten all 10-32 x 5/8 in.
screws to a torque of 25 in-lb (29 cm-kg).
Proceed to Attaching a PC or terminal on page 32.
4-post rack mount installation
Kits for 4-post rack mounting are not included in the shipping carton and must be ordered separately.
NOTE
Use the following procedure when installing the Brocade ICX 6650 in a 4-post rack cabinet. For 2-post
cabinets, follow the procedures in 2-post rack mount installation on page 28.
Use the following steps to mount the Brocade ICX 6650 in a 4-post rack.
1. Remove the rack mount kit from the shipping carton. The kit contains the following:
•
•
•
•
Two L-shaped mounting brackets.
Four rack mount rails: two for side attach and two for rear attach racks.
Thirty-two 8-32 x 5/16 in., panhead Phillips screws with patchlocks.
Eight 10-32 x 5/8 in., panhead Phillips screws (torque to 25 in-lb, 29 cm-kg). Refer to item 1 in
the following figure.
• Eight 32-10 retainer nuts (for square-hole rack rails). Refer to item 2 in the following figure.
• Eight 32-10 retainer nuts (for round-hole rack rails). Refer to item 3 in the following figure.
30
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Installing the Brocade ICX 6650
FIGURE 12 4-post screws and retainer nuts
NOTE
Do not use the hardware supplied in a 2-post rack mounting kit to mount a Brocade ICX 6650 in a 4post rack. Mounting the device in a 4-post rack requires additional hardware to prevent drooping from
possible flexing and distortion of the 4-post rack when a device is not properly installed.
2. Attach the mounting brackets to the sides of the device as illustrated in 2-post rack mount installation
on page 28 using the 8-32 x 5/16 in. screws.
3. Attach the appropriate rails: either side attach or rear attach as determined by the type of rack in
which you are installing the device.
The following figures show exploded views of the optional 4-post rack mount kit.
FIGURE 13 Optional 4-post rack mount kit, rear attachment
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
31
Attaching a PC or terminal
FIGURE 14 Optional 4-post rack mount kit, side attachment
4. Position the switch in the cabinet, providing temporary support under the switch until the rail kit is
secured to the cabinet.
5. Attach the front right bracket to the rail rack using two 10-32 x 5/8 in. screws and the appropriate
round-hole or square-hole retainer nuts.
6. Repeat step 5 to attach the left front bracket to the left front rack rail and tighten all 10-32 x 5/8 in.
screws to a torque of 25 in-lb (29 cm-kg).
7. Attach the rear right bracket to the rail rack using two 10-32 x 5/8 in. screws and the appropriate
round-hole or square-hole retainer nuts.
8. Repeat step 7 to attach the rear left bracket to the rail rack and tighten all 10-32 x 5/8 in. screws to
a torque of 25 in-lb (29 cm-kg).
Proceed to Attaching a PC or terminal on page 32.
Attaching a PC or terminal
To assign an IP address, you must have access to the command line interface (CLI). The CLI is a textbased interface that can be accessed through a direct serial connection to the device and through
Telnet connections. The CLI is described in detail in the FastIron Ethernet Switch Administration
Guide.
Access the CLI by connecting to the console port. After you assign an IP address, you can access the
system through Telnet, the Web management interface, or Brocade Network Advisor.
Use the following steps to attach a management station to the console port.
1. Connect a PC or terminal to the console management port on the rear of the Brocade ICX 6650
using the mini-USB serial console port cable (Part number 50-1000059-01).
For port pinout information for the mini-USB serial console port, refer to Pinouts and signaling on
page 72.
32
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Powering on the system
NOTE
You must run a terminal emulation program on the PC.
2. Launch the terminal emulation program and set the following session parameters:
•
•
•
•
•
Baud: 9600 bps
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
The console serial communication port serves as a connection point for management by a PC.
Powering on the system
After you complete the physical installation, you can power on the system.
1. Remove the power cable from the shipping package container.
2. Attach the AC power cable to the AC connector on the rear panel.
3. Insert the power cable plug into a 100V-240V outlet.
NOTE
To turn the system off, simply unplug the power cable or cables.
NOTE
The socket should be installed near the equipment and should be easily accessible.
Power supplies
Each Brocade ICX 6650 comes with two alternating-current (AC) power supplies. The Brocade ICX
6650 device also supports direct-current (DC) power supplies. The Brocade ICX 6650 is capable of
running on one power supply and one fan. The second set provide redundancy.
If the second power supply and fan slots are unused, you must cover them with filler panels.
NOTE
When running two power supplies, they must be of the same type: either two alternating-current (AC)
power supplies or two direct-current (DC) power supplies. AC and DC units cannot be mixed in a
device.
Installing and replacing a power supply unit
When installing or replacing a power supply unit, keep in mind the following:
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
33
Installing an AC power supply
• Power supplies can be swapped in or out while the device is running. The remaining power supply
provides enough power for the device.
• The airflow direction of the power supply must match that of the installed fan tray. All must be either
exhaust or intake.
CAUTION
Remove the power cord from a power supply before you install it in or remove it from the
device. Otherwise, the power supply or the device could be damaged as a result. (The device
can be running while a power supply is being installed or removed, but the power supply itself
should not be connected to a power source.)
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or
an orange arrow with an "I."
Installing an AC power supply
You need a #2 Phillips screwdriver and a flat-head screwdriver for installation.
Brocade recommends using an ESD wrist strap during installation.
FIGURE 15 Installing an AC power supply unit
Use the following steps to install an AC power supply in the switch.
1. If replacing a power supply, remove the previously installed power supply from the appropriate slot
by removing the two screws with a flat-head screwdriver.
2. If installing a new power supply into a slot covered with a filler panel:
a)
b)
Using a Phillips screwdriver, unscrew the screws on the filler panel.
Remove the filler panel.
3. Before opening the package that contains the power supply, touch the bag to the switch casing to
discharge any potential static electricity.
4. Remove the power supply from the anti-static shielded bag.
34
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Installing a DC power supply
5. Holding the power supply level, guide it into the carrier rails on each side and gently push it all the
way into the slot, ensuring that it firmly engages with the connector.
6. When you are sure the power supply has properly engaged the connector, tighten the retainer
screws to secure the power supply in the slot.
When the device is powered on, the AC or DC LEDs on the power supply back panel should light green
to confirm that the power supply is correctly installed and supplying power.
You can also verify correct installation by running the show chassis command, as shown in this
example:
Device#show chassis
The stack unit 1 chassis info:
Power supply 1 (AC - Regular) present, status ok
Model Number: 23-0000144-01
Serial Number: 028
Firmware Ver: A
Power supply 1 Fan Air Flow Direction: Front to Back
Power supply 2 not present
Fan 1 ok, speed (auto): [[1]]<->2
Fan 2 ok, speed (auto): [[1]]<->2
Fan controlled temperature: 37.5 deg-C
Fan speed switching temperature thresholds:
Speed 1: NM<----->70 deg-C
Speed 2: 65<-----> 85 deg-C (shutdown)
Fan 1 Air Flow Direction: Front to Back
Fan 2 Air Flow Direction: Front to Back
MAC-Back Temperature Readings:
Current temperature : 37.5 deg-C
MAC-Left Temperature Readings:
Current temperature : 34.0 deg-C
MAC-Right Temperature Readings:
Current temperature : 33.0 deg-C
MAC-Front Temperature Readings:
Current temperature : 33.0 deg-C
CPU Temperature Readings:
Current temperature : 37.5 deg-C
Center Temperature Readings:
Current temperature : 30.5 deg-C
sensor A Temperature Readings:
Current temperature : 37.5 deg-C
sensor B Temperature Readings:
Current temperature : 31.0 deg-C
sensor C Temperature Readings:
Current temperature : 34.5 deg-C
sensor D Temperature Readings:
Current temperature : 30.5 deg-C
Warning level.......: 45.0 deg-C
Shutdown level......: 85.0 deg-C
Boot Prom MAC : 748e.f893.eabe
Management MAC: 748e.f893.eabe
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
Installing a DC power supply
DANGER
Do not power on the DC power supply until you have wired the connector and installed the unit
into the device.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
35
Installing the Brocade ICX 6650
CAUTION
For the DC input circuit to the system, make sure there is a 20 Amp circuit breaker, minimum
60 VDC, double pole, on the input terminal block to the power supply. The input wiring for
connection to the product should be copper wire, 12 AWG, marked VW-1, and rated minimum
90°C.
CAUTION
For DC system, use grounding wire of at least 12 American Wire Gauge (AWG). The grounding
wire should be attached to the DC input connector; the other end connects to the building
ground.
NOTE
AC and DC power supplies cannot be installed and used in the same device. Mismatched power
supplies in the same device cause continual reboot on power up.
FIGURE 16 DC power supply unit
You need a #2 Phillips screwdriver and a flat-head screwdriver for installation.
Brocade recommends using an ESD wrist strap during installation.
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
1. Remove the previously installed power supply from the appropriate slot by removing the chassis
attachment screws located in the upper right and lower left of the power supply unit using a flathead screwdriver.
36
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Installing the Brocade ICX 6650
FIGURE 17 DC power supply screws
1 Chassis attachment screws
2 Assembly screws
2. Before opening the package that contains the DC power supply, touch the bag to the switch casing to
discharge any potential static electricity.
3. Remove the DC power supply from the anti-static shielded bag.
4. Insert the DC power supply source wires into the DC wiring assembly, matching the terminals.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
37
Installing the Brocade ICX 6650
FIGURE 18 DC power supply wiring assembly
1 Wire tightening screws
2 DC power source wires
3 Earth ground wire
4 Assembly screws
5. Use the wire tightening screws to secure the wires.
6. Insert the earth ground wire into the ground terminal on the DC wiring assembly.
ATTENTION
This equipment installation must meet NEC/CEC Code requirements. Consult local authorities for
regulations.
7. Insert the DC power supply wiring assembly with the wires connected into the power supply and
tighten the assembly screws.
38
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Installing an SFP+ transceiver
8. Using the handle on the power supply, hold the power supply level and guide it into the carrier rails
on each side of the power supply slot. Gently push the power supply all the way into the slot,
ensuring that it firmly engages with the connector.
FIGURE 19 Installing a DC power supply unit
9. When you are sure the power supply has properly engaged the connector, tighten the chassis
attachment screws to secure the power supply in the slot.
When the device is powered on, the power LED on the device should turn green to confirm that the
power supply is correctly installed and supplying power.
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
Installing an SFP+ transceiver
To monitor the transceivers, the show media command output shows the transceiver information for all
interfaces on the switch. Third-party transceivers are allowed. Brocade provides support for third-party
transceivers, but may require a Brocade transceiver be used for troubleshooting.
Support will not be provided if there is an issue with the third-party transceiver.
Complete the following steps to install an SFP+ transceiver.
1. Remove any protector plugs from the transceivers and the ports.
2. Making sure that the bail (wire handle) is in the unlocked position, place the SFP+ transceiver in the
correctly oriented position on the port.
NOTE
The QSFP+ 40 GbE LR4 optical transceiver is supported in ports 1 and 2 only. When the module is
inserted into a stack-unit/slot number/port number combination that is not 1/2/1 or 1/2/2, the following
error message displays: “QSFP LR-4 optics not supported on port port-number.”
3. Slide the SFP+ transceiver into the port until you feel it click into place; then close the bail.
NOTE
Each SFP+ transceiver has a 10-pad gold-plated edge connector on the bottom. The correct position
to insert an SFP+ transceiver in the upper row of ports is with the gold-plated edge down. The correct
position to insert an SFP+ transceiver in the lower row of ports is with the gold-plated edge up.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
39
Installing the Brocade ICX 6650
FIGURE 20 Installing an SFP+ transceiver in a port slot
40
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Configuring the Brocade ICX 6650
● Assigning permanent passwords.................................................................................... 41
● Configuring IP addresses................................................................................................42
● Connecting network devices........................................................................................... 46
● Testing connectivity.........................................................................................................47
● Troubleshooting network connections.............................................................................48
Assigning permanent passwords
By default, the CLI is not protected by passwords. To secure CLI access, Brocade strongly
recommends assigning passwords. Refer to the FastIron Ethernet Switch Administration Guide.
You can set the following levels of Enable passwords:
• Super User - Allows complete read-and-write access to the system. This is generally for system
administrators and is the only password level that allows you to configure passwords.
NOTE
You must set a Super User password before you can set other types of passwords.
• Port Configuration - Allows read-and-write access for specific ports but not for global (system-wide)
parameters.
• Read Only - Allows access to the Privileged EXEC mode and CONFIG mode but only with read
access.
Setting passwords
1. At the opening CLI prompt, enter the following command to change to the Privileged EXEC mode:
device> enable
2. Access the CONFIG level of the CLI by entering the following command:
device# configure terminal
device(config)#
3. Enter the following command to set the Super User password:
device(config)# enable super-user-password text
NOTE
You must set the Super User password before you can set other types of passwords.
4. Enter the following commands to set the port configuration and read-only passwords:
device(config)# enable port-config-password text
device(config)# enable read-only-password text
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
41
Recovering from a lost password
NOTE
If you forget your Super User password, refer to Recovering from a lost password on page 42.
Syntax: enable { super-user-password | read-only-password | port-config-password } text
Passwords can be up to 32 characters long.
Recovering from a lost password
By default, the CLI does not require passwords. However, if a password has been configured for the
device but the password has been lost, you can regain Super User access to the device using the
following procedure.
NOTE
Recovery from a lost password requires direct access to the serial port and a system reset.
1. Start a CLI session over the serial interface to the Brocade device.
2. Reboot the device.
3. While the system is booting, before the initial system prompt appears, enter b to enter the boot
monitor mode.
4. Enter no password. (You cannot abbreviate this command.)
After the console prompt reappears, assign a new password.
Configuring IP addresses
You must configure at least one IP address using the serial connection to the CLI before you can
manage the system using the other management interfaces.
Brocade devices support both classical IP network masks (Class A, B, and C subnet masks, and so
on) and Classless Interdomain Routing (CIDR) network prefix masks.
• To enter a classical IP network mask, enter the mask in IP address format. For example, enter
"209.157.22.99 255.255.255.0" for an IP address with a Class C subnet mask.
• To enter a prefix number for a network mask, enter a forward slash ( / ) and the number of bits in
the mask immediately after the IP address. For example, enter "209.157.22.99/24" for an IP
address that has a network mask with 24 significant ("mask") bits.
By default, the CLI displays network masks in classical IP address format (for example,
255.255.255.0). You can change the display to the prefix format. Refer to the FastIron Ethernet Switch
Administration Guide.
Devices running Layer 2 software
Use the following procedure to configure an IP address on a device running Layer 2 software.
42
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Devices running Layer 3 software
1. At the opening CLI prompt, enter enable.
device> enable
2. Enter the following command at the Privileged EXEC level prompt, then press Enter. This command
erases the factory test configuration if still present.
device# erase startup-config
CAUTION
Use the erase startup-config command only for new systems. If you enter this command on a
system you have already configured, the command erases the configuration. If you
accidentally do erase the configuration on a configured system, enter the write memory
command to save the running configuration to the startup-config file.
3. Access the configuration level of the CLI by entering the following command:
device# configure terminal
device(config)#
4. Configure the IP addresses and mask for the switch.
device(config)# ip address 192.168.0.0 255.255.255.0
5. Set a default gateway address for the switch.
device(config)# ip default-gateway 192.168.0.0
NOTE
You do not need to assign a default gateway address for single subnet networks.
Devices running Layer 3 software
Before attaching equipment to a Brocade ICX 6650, you must assign an interface IP address to the
subnet on which the router connected to the switch will be located. You must use the serial connection
to assign the first IP address. For subsequent addresses, you also can use the CLI through Telnet or
the Web management interface.
By default, you can configure up to 24 IP addresses on each port, virtual interface, and loopback
interface. You can increase this amount to up to 64 IP subnet addresses per port by increasing the size
of the subnet-per-interface table.
The following procedure shows how to add an IP address and mask to a router port.
1. At the opening CLI prompt, enter enable.
device> enable
2. Enter the following command at the Privileged EXEC level prompt, and then press Enter. This
command erases the factory test configuration if still present.
device# erase startup-config
CAUTION
Use the erase startup-config command only for new systems. If you enter this command on a
system you have already configured, the command erases the configuration. If you
accidentally do erase the configuration on a configured system, enter the write memory
command to save the running configuration to the startup-config file.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
43
Configuring IP parameters for devices running Layer 3 software
3. Access the configuration level of the CLI by entering the following command.
device# configure terminal
device(config)#
4. Configure the IP addresses and mask addresses for the interfaces on the router.
device(config)# interface e 1/1/1
device(config)# ip address 192.168.0.0 255.255.255.0
NOTE
You can use the ip address ip-addr /mask-bits command if you know the subnet mask length. In
the example in step 4, you could enter ip address 192.168.0.0/24.
Use the secondary parameter if you have already configured an IP address within the same subnet
on the interface.
Configuring IP parameters for devices running Layer 3 software
This section describes how to configure IP parameters for devices running Layer 3 software.
Configuring IP addresses
You can configure an IP address on the following types of Layer 3 switch interfaces:
• Ethernet port
• Virtual routing interface (also called a Virtual Ethernet or "VE")
• Loopback interface
By default, you can have up to 24 IP addresses on each interface, but you can increase this number to
128 IP addresses.
NOTE
Once you configure a virtual routing interface on a VLAN, you cannot configure Layer 3 interface
parameters on individual ports in the VLAN. Instead, you must configure the parameters on the virtual
routing interface itself.
Brocade devices support both classical IP network masks (Class A, B, and C subnet masks, and so
on) and Classless Interdomain Routing (CIDR) network prefix masks.
• To enter a classical IP network mask, enter the mask in IP address format. For example, enter
"209.157.22.99 255.255.255.0" for an IP address with a Class C subnet mask.
• To enter a prefix network mask, enter a forward slash ( / ) and the number of bits in the mask
immediately after the IP address. For example, enter "209.157.22.99/24" for an IP address that has
a network mask with 24 significant bits (ones).
By default, the CLI displays network masks in classical IP address format (for example,
255.255.255.0). You can change the display to prefix format.
Assigning an IP address to an Ethernet port
Enter the following commands to assign an IP address to port 1/1/1.
device(config)# interface ethernet 1/1/1
device(config-if-1/1/1)# ip address 192.168.0.0 255.255.255.0
44
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Configuring the Brocade ICX 6650
You also can enter the IP address and mask in CIDR format, as follows:
device(config-if-1/1/1)# ip address 192.168.0.0/24
Syntax: [no] ip address ip-addr ip-mask
or
Syntax: [no] ip address ip-addr/mask-bits
Assigning an IP address to a loopback interface
Loopback interfaces are always up, regardless of the states of physical interfaces. They can add
stability to the network because they are not subject to route flap problems that can occur due to
unstable links between a Layer 3 switch and other devices. You can configure up to four loopback
interfaces on a Layer 3 switch.
You can add up to 24 IP addresses to each loopback interface.
To add a loopback interface, enter commands such as those shown in the following example:
device(config)# interface loopback 1
device(config-lbif-1)# ip address 192.168.0.0/24
Syntax: interface loopback num
The num parameter specifies the virtual interface number. You can specify from 1 through the
maximum number of virtual interfaces supported on the device. To display the maximum number of
virtual interfaces supported on the device, enter the show default values command.
Assigning an IP address to a virtual routing interface
A virtual interface is a logical port associated with a Layer 3 Virtual LAN (VLAN) configured on a Layer 3
switch. You can configure routing parameters on the virtual interface to enable the Layer 3 switch to
route protocol traffic from one Layer 3 VLAN to the other, without using an external router.
NOTE
The switch uses the lowest MAC address on the device (the MAC address of port 1 or 1/1/1) as the
MAC address for all ports within all virtual interfaces you configure on the device.
Enter commands similar to the following to add a virtual interface to a VLAN and configure an IP
address on the interface.
device(config)# vlan 2 name IP-Subnet_1.1.2.1/24
device(config-vlan-2)# untag 1/1/1 to 1/1/4
device(config-vlan-2)# router-interface ve1
device(config-vlan-2)# interface ve1
device(config-vif-1)# ip address 1.1.2.1/24
The first two commands in this example create a Layer 3 protocol-based VLAN named "IPSubnet_1.1.2.1/24" and add a range of untagged ports to the VLAN. The router-interface command
creates virtual interface 1 as the routing interface for the VLAN. The last two commands change to the
interface configuration level for the virtual interface and assign an IP address to the interface.
Syntax: router-interface venum
Syntax: interface venum
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
45
Deleting an IP address
Deleting an IP address
Enter a command similar to the following to delete an IP address.
device(config-if-1/1/1)# no ip address 1.1.2.1
This command deletes IP address 1.1.2.1. You do not need to enter the subnet mask.
To delete all IP addresses from an interface, enter the following command.
device(config-if-1/1/1)# no ip address *
Syntax: no ip address ip-addr | *
Connecting network devices
Brocade devices support connections to other vendors’ routers, switches, and hubs, as well other
Brocade devices.
Connectors
For port pinouts, refer to Pinouts and signaling on page 72.
Connecting a network device to a fiber port
For direct attachment from the device to a Gigabit NIC, switch, or router, using a fiber-optic
transceiver, you need fiber cabling with an LC connector.
For information about transceivers supported on the Brocade ICX 6650, refer to the following Brocade
website:
http://www.myBrocade.com/downloads/documents/data_sheets/product_data_sheets/Optics_DS.pdf
To connect the device to another network device using a fiber port, you must perform the following
tasks:
• Install a fiber-optic transceiver (SFP or SFP+).
• Cable the fiber-optic transceiver.
Installing a transceiver
You can install a new transceiver in an SFP+ slot while the device is powered on and running.
While installing a transceiver, wear an ESD wrist strap with a plug for connection to a metal surface.
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
DANGER
All fiber-optic interfaces use Class 1 lasers.
Use the following steps to install a transceiver:
46
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Cabling a fiber-optic transceiver
1. Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as
an equipment rack) to act as ground.
2. Remove the new transceiver from the protective packaging.
3. Gently insert the transceiver into the slot until it clicks into place. Transceivers are keyed to prevent
incorrect insertion.
Cabling a fiber-optic transceiver
Perform the following steps to cable a fiber-optic transceiver.
1. Remove the protective covering from the fiber-optic port connectors and store the covering for future
use.
NOTE
Before cabling a fiber-optic transceiver, Brocade strongly recommends cleaning the cable connectors
and the port connectors. For more information, refer to Cleaning the fiber-optic connectors on page
59.
2. Gently insert the cable connector (a tab on each connector should face upward) into the transceiver
connector until the tabs lock into place.
3. Observe the link and active LEDs to determine if the network connections are functioning properly.
For more information about the LED indicators, refer to LED activity interpretation on page 49.
Cleaning the fiber-optic connectors
To avoid problems with the connection between the fiber-optic transceiver (SFP, SFP+, or QSFP+) and
the fiber cable connectors, Brocade strongly recommends cleaning both connectors each time you
disconnect and reconnect them. Dust can accumulate in the connectors and cause problems, such as
reducing the optic launch power.
To clean the fiber cable connectors, Brocade recommends using a fiber-optic reel-type cleaner. When
not using an SFP connector, make sure to keep the protective covering in place.
Testing connectivity
Test for connectivity by observing the LEDs related to network connection.
Pinging an IP address
To verify that a Brocade ICX 6650 can reach another device through the network, enter a command
similar to the following at any level of the CLI.
device# ping 192.168.0.0
Syntax: ping ip_addr [ source ip_addr ] [ count num ] [ timeout msec ] [ ttl num ] [ verify ] [ nofragment ] [ quiet ] [ data 1-to-4 byte hex#, e.g. abcdef00 ] [ numeric ] [ size byte ] [ brief [ max-printper-sec num 0-2047 ] ]
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
47
Tracing a route
NOTE
If you address the ping to the IP broadcast address, the device lists the first four responses.
If a problem persists after taking these actions, contact Brocade Technical Support.
Tracing a route
To determine the path through which a Brocade device can reach another device, enter a command
similar to the following at any level of the CLI.
Brocade# traceroute 192.168.0.0
Syntax: traceroute host-ip-addr [ maxttl value ] [ minttl value ] [ numeric ] [ timeout value ] [
source-ip ipaddr ]
The CLI displays trace route information for each hop as soon as the information is received.
Traceroute requests display all responses to a given TTL. In addition, if there are multiple equal-cost
routes to the destination, the Brocade device displays up to two responses by default.
Troubleshooting network connections
• For the indicated port, verify that both ends of the cabling (at the device and the connected device)
are snug.
• Verify that the device and the connected device are both powered on and operating correctly.
• Verify that you have used the correct cable type for the connection:
‐
‐
For twisted-pair connections to an end node, use straight-through cabling.
For fiber-optic connections, verify that the transmit port on the device is connected to the
receive port on the connected device, and that the receive port on the device is connected
to the transmit port on the connected device.
• Use the CLI to verify that the port has not been disabled through a configuration change. If you
have configured an IP address on the device, you also can use the Web management interface or
Brocade Network Advisor.
• If the other procedures do not resolve the problem, try using a different port or a different cable.
48
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Operation
● LED activity interpretation............................................................................................... 49
● Brocade ICX 6650 front panel LEDs............................................................................... 49
● Brocade ICX 6650 rear panel LEDs................................................................................50
● LED patterns................................................................................................................... 51
● Brocade ICX 6650 maintenance..................................................................................... 53
● Diagnostic tests and monitoring...................................................................................... 53
LED activity interpretation
System activity and status can be determined through the activity of the LEDs on the switch.
There are three possible LED states: off (no light), a steady light, and a flashing light. Flashing lights
may be slow, fast, or flickering. The LED colors are blue, green, or amber.
Sometimes, the LEDs flash either of the colors during boot, POST, or other diagnostic tests. This is
normal; it does not indicate a problem unless the LEDs do not indicate a healthy state after all boot
processes and diagnostic tests are complete.
Brocade ICX 6650 front panel LEDs
The Brocade ICX 6650 has the following LEDs on the front panel:
•
•
•
•
Two power supply unit (PSU) bicolor status LEDs (green and amber) labeled PSU1 and PSU2
One DIAG status LED (green and amber)
One MS status LED (green and amber)
Four 1x40 GbE QSFP port status and activity LEDs (blue) which indicate the status of the 40 GbE
ports located on the rear panel
• Eight 4x10 GbE QSFP-to-SFP breakout port status and activity LEDs (green) which indicate the
status of the 4x10 GbE breakout ports located on the rear panel
• 56 10 GbE bicolor status LEDs (green for 10 GbE and amber for 1 GbE) which indicate the mode of
operation
In the following figure, the up-arrow port status LEDs for the 1/10 GbE ports correspond to the upper,
odd-numbered ports; the down-arrow port status LEDs correspond to the lower, even-numbered ports.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
49
Brocade ICX 6650 rear panel LEDs
FIGURE 21 Brocade ICX 6650 front panel LEDs and port numbering
1.
2.
3.
4.
5.
6.
7.
Push button reset
PSU1 and PSU2 status LEDs
DIAG and MS status LEDs
40 GbE QSFP rear port status/activity LEDs
4x10 GbE QSFP-to-SFP breakout port status/activity LEDs
1/10 GbE port status LEDs
Port numbering (odd-numbered port at top, even-numbered port at bottom)
Brocade ICX 6650 rear panel LEDs
The Brocade ICX 6650 has the following LEDs on the rear panel:
• Six 40 GbE QSFP+ port status LEDs (green)
• One DIAG LED bicolor status LED (green and amber)
• Two Management port status LEDs
50
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
LED patterns
FIGURE 22 Brocade ICX 6650 rear panel LEDs and ports
1.
2.
3.
4.
5.
Mini-USB connector console port
Management port status LEDs
40 GbE ports
Ethernet management port
40 GbE port status LEDs
LED patterns
This section describes the Brocade ICX 6650 LED patterns.
PSU 1 and PSU2
TABLE 6 PSU 1 and PSU2
LED State
Status of hardware
Recommended action
Off (no light)
System is off or there is no power.
Verify the system is on and has completed booting.
Steady green
PSU is on and functioning properly.
No action required.
Steady amber
PSU is in faulty state or missing power.
Replace power supply.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
51
Brocade ICX 6650 Operation
DIAG LED
TABLE 7 DIAG LED
LED State
Status of hardware
Recommended action
Off (no light)
Diagnostic is off.
No action required.
Blinking green System self-diagnostic test is in progress.
No action required.
Steady green
No action required.
System self-diagnostic test is successfully completed. Device reboots
and clears back to off.
Steady amber System self-diagnostic test has detected a fault.
Contact support.
Management port status LED
TABLE 8 Management port status LED
LED State
Status of hardware
Recommended action
Off (no light)
Not cabled.
No action required
Blinking
There is traffic and packets are being transmitted or received.
No action required.
Steady
No traffic being transmitted, but link is up.
No action required.
1/10 GbE SFP+ port LEDs
TABLE 9 1/10 GbE SFP+ port LEDs
LED State
Status of hardware
Recommended action
Green
Link is up in 10 GbE mode.
No action required.
Blinking green
There is 10 GbE activity (traffic) and packets are being transmitted or
received.
No action required.
Amber
Link is up in 1 GbE mode.
No action required.
Blinking amber There is 1 GbE activity (traffic) and packets are being transmitted or
received.
52
No action required.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 maintenance
40 GbE QSFP+ rear port LEDs on front panel
TABLE 10 40 GbE QSFP+ rear port LEDs on front panel
LED State
Status of hardware
Recommended action
Off (no light)
Not enabled.
No action required.
Blue
Link is up in 40 GbE mode.
No action required.
Blinking blue
Indicates activity, and packets are being transmitted or received.
No action required.
4x10 GbE QSFP+ rear port LEDs on front panel
TABLE 11 4x10 GbE QSFP+ rear port LEDs on front panel
LED State
Status of hardware
Recommended action
Off (no light)
Not enabled.
No action required.
Green
Link is up in 10 GbE mode.
No action required.
Blinking green
Indicates activity, and packets are being transmitted or received.
No action required.
Brocade ICX 6650 maintenance
The Brocade ICX 6650 is designed for high availability and low failure; it does not require any regular
physical maintenance. Supported transceivers and diagnostic tests are described in the following
sections.
Diagnostic tests and monitoring
Brocade FastIron software includes diagnostic tests to help you troubleshoot the hardware. System
diagnostic software is designed to fulfill the purpose of offline diagnostics. In offline diagnostics, you
must turn on or off the diagnostic flags to execute diagnostic tests during the next bootup.
The CLI commands for system diagnostic tests are dm diag and dm alt-diag. These diagnostic tests
verify all available hardware components including:
•
•
•
•
•
I2C devices
EEPROMS
CPU packet
Test MAC alignment
Line rate
During system diagnostic testing, the system is completely under the control of the diagnostic software.
All hardware components are verified, and results are displayed on the console. In cases where a
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
53
Brocade ICX 6650 Operation
failure is detected, results and corrective actions will be displayed. After the system diagnostic testing
is complete, the system exits from the diagnostic mode and reloads the system for normal operation.
System diagnostic testing runs at link speeds 10 Gbps and 40 Gbps (QSFP ports) depending on the
speed of the link being tested and the type of port.
54
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Managing the Brocade ICX 6650
● Managing temperature settings.......................................................................................55
● Removing MAC address entries..................................................................................... 57
● Displaying Brocade ICX 6650 CPU usage......................................................................57
● Hardware maintenance schedule....................................................................................58
● Replacing a copper or fiber-optic module....................................................................... 58
● FRU removal and replacement procedures.................................................................... 60
● Replacing a power supply unit........................................................................................ 61
● Replacing fan trays......................................................................................................... 63
Managing temperature settings
The device contains temperature sensors that the software reads based on a configurable device poll
time. To protect the device from overheating, the following temperature threshold levels exist:
• The warning level is the temperature at which the device generates a syslog message and SNMP
trap. It is configurable.
• The shutdown level is the temperature at which the device reboots. It is set by the device and is not
configurable.
The fan speed settings are set by the device, and are not configurable.
Displaying the temperature
To display the temperature of a device, enter the show chassis command at any level of the CLI.
NOTE
The temperature displayed by the show chassis command reflects the temperature of the board inside
the device.
device#show chassis
The stack unit 1 chassis info:
Power
Power
Power
Power
supply
supply
supply
supply
1
1
2
2
(NA
Fan
(NA
Fan
- AC - Regular) present,
Air Flow Direction: Back
- AC - Regular) present,
Air Flow Direction: Back
status ok
to Front
status ok
to Front
Fan 1 ok, speed (auto): [[1]]<->2
Fan 2 ok, speed (auto): [[1]]<->2
Fan controlled temperature: 47.5 deg-C
Fan speed switching temperature thresholds:
Speed 1: NM<----->68 deg-C
Speed 2: 63<-----> 85 deg-C (shutdown)
Fan 1 Air Flow Direction: Back to Front
Fan 2 Air Flow Direction: Back to Front
MAC-Back Temperature Readings:
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
55
Displaying syslog messages for temperature
Current temperature : 41.5 deg-C
MAC-Left Temperature Readings:
Current temperature :
MAC-Right Temperature Readings:
Current temperature :
MAC-Front Temperature Readings:
Current temperature :
CPU Temperature Readings:
Current temperature :
Center Temperature Readings:
Current temperature :
sensor A Temperature Readings:
Current temperature :
sensor B Temperature Readings:
Current temperature :
sensor C Temperature Readings:
Current temperature :
sensor D Temperature Readings:
Current temperature :
Warning level.......:
Shutdown level......:
42.0 deg-C
42.5 deg-C
44.5 deg-C
41.0 deg-C
26.0 deg-C
34.5 deg-C
35.5 deg-C
47.5 deg-C
39.5 deg-C
68.0 deg-C
85.0 deg-C
Boot Prom MAC : 00.00.00
Management MAC: 00-00-00
Syntax: show chassis
Displaying syslog messages for temperature
The software sends a syslog message and an SNMP trap if the temperature crosses the warning or
shutdown thresholds. The following method describes how to view the system log on the device. If you
have configured the device to use a syslog server or SNMP trap receiver, refer to the documentation
for the server or receiver.
To display the system log, enter the show log command at any CLI level.
device# show log
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
Buffer logging: level ACDMEINW, 8 messages logged
level code: A=alert C=critical D=debugging M=emergency E=error
I=informational N=notification W=warning
Static Log Buffer:
Dynamic Log Buffer (50 entries):
at 0 days 0 hours 2 minutes 0 seconds, level alert
Temperature 48.0 C degrees, warning level 45.0 C degrees, shutdown level 55.0 C
degrees
at 0 days 0 hours 1 minutes 0 seconds, level alert
Temperature 40.0 C degrees, warning level 35.0 C degrees, shutdown level 45.0 C
degrees
Changing the temperature warning level
To change the temperature at which the device sends a syslog message and an SNMP trap, enter a
command similar to the following at the Privileged EXEC level of the CLI.
device# temperature warn 85
Syntax: temperature warn value
The value variable is the temperature warning level, in Celsius. The maximum value of the
temperature warning level is 5 degrees below the shutdown level, which is automatically set by the
device.
If you change the device hardware configuration (for example, by adding a fan tray), the device may
change the temperature shutdown level the next time it boots. This can result in the temperature
56
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Changing the temperature poll time
warning level being higher than the temperature shutdown level. If this happens, a warning message is
displayed during bootup.
Changing the temperature poll time
By default, the software polls the temperature sensor every 60 seconds to get the current temperature.
This poll rate is controlled by the device poll time, which also controls how often the software polls other
system components.
To change the poll time, enter a command similar to the following at the global CONFIG level.
device(config)# chassis poll-time 200
Syntax: chassis poll-time value
The value variable can be from 0 through 65535.
Removing MAC address entries
You can remove the following types of learned MAC address entries from the system MAC address
table:
•
•
•
•
All MAC address entries
All MAC address entries for a specified Ethernet port
All MAC address entries for a specified VLAN
A specified MAC address entry in all VLANs
For example, to remove entries for the MAC address 00.00.00 in all VLANs, enter the following
command at the Privileged EXEC level of the CLI.
device# clear mac-address 00.00.00
Syntax: clear mac-address [mac-address | ethernet port-num | vlan number]
If you enter the clear mac-address command without any parameters, the software removes all MAC
entries.
Use the mac-address parameter to remove a specified MAC address from all VLANs. Specify the MAC
address in the following format: HHHH.HHHH.HHHH.
Use the ethernet port-num parameter to remove all MAC addresses for a specified Ethernet port.
Use the vlan number parameter to remove all MAC addresses for a specified VLAN.
Displaying Brocade ICX 6650 CPU usage
You can display the amount of the CPU in use. To do so, enter the show cpu command at any level of
the CLI.
device# show cpu
31 percent busy, from 3248 sec ago
1
sec avg: 10 percent busy
5
sec avg: 10 percent busy
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
57
Hardware maintenance schedule
60 sec avg:
300 sec avg:
10 percent busy
10 percent busy
Syntax: show cpu
Hardware maintenance schedule
Brocade ICX 6650 switch hardware components require minimal maintenance. Brocade recommends
cleaning the fiber-optic connectors on a fiber-optic port and the connected fiber cable each time you
disconnect the cable.
Replacing a copper or fiber-optic module
You can remove an SFP+ or QSFP+ transceiver from a slot and replace it with a new one while the
Brocade ICX 6650 is powered on and running.
This section provides information about the following tasks:
• Removing a copper or fiber-optic module
• Cabling a fiber-optic module
• Cleaning the fiber-optic connectors
Removing a copper or fiber-optic module
You can remove a copper or fiber SFP+ or QSFP+ transceiver from a slot while the Brocade ICX 6650
is powered on and running.
While removing a copper or fiber-optic module, be sure to wear an ESD wrist strap with a plug that can
be inserted in the ESD connector on the Brocade ICX 6650.
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
To remove a copper or fiber-optic module from an SFP slot, do the following.
1. Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as
an equipment rack).
2. Disconnect the copper or fiber cable connector from the port connector.
3. Unlock the copper or fiber-optic module by pulling the bail latch forward, away from the front panel
of the module, as shown in the following figure.
NOTE
On 1000Base-SX ports, the bail latch is enclosed in a black sleeve, and on 1000Base-LX ports, the
bail latch is enclosed in a blue sleeve.
58
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Cabling a fiber-optic module
1
Bail Latch
FIGURE 23 Unlocking the bail latch
NOTE
The bail latch may be attached to either the top or the bottom of the SFP+ or QSFP+ transceiver.
4. Grasp the bail latch and pull the copper or fiber-optic module out of the port, as shown in the
following figure.
FIGURE 24 Removing the fiber-optic module
5. Store the copper or fiber-optic module in a safe, static-free place or in an anti-static bag.
6. Install a new copper or fiber-optic module in the port.
Cabling a fiber-optic module
For instructions on cabling a fiber-optic module, refer to Cabling a fiber-optic transceiver on page 47.
Cleaning the fiber-optic connectors
For instructions on cleaning a fiber-optic module, refer to Cleaning the fiber-optic connectors on page
47.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
59
FRU removal and replacement procedures
FRU removal and replacement procedures
The field-replaceable units (FRUs) in the Brocade ICX 6650 can be removed and replaced without
special tools. The switches can continue operating during the FRU replacement if the conditions
specified in these procedures are followed. This covers both the power supply unit (PSU) FRUs and
fan FRUs.
NOTE
This document describes how to change FRUs for units with either an air intake or air exhaust. You
must replace a failed FRU with a FRU of the same type. This applies to both power supplies and fans.
A new FRU must have the same part number (P/N) as the FRU being replaced. The manufacturing
P/N is located on the top of the FRU.
If a mismatched power source or fan assembly is installed by mistake, a warning is sent to the
console. The warning messages will be similar to the following:
• For a fan mismatch: WARNING, Brocade ICX 6650, MISMATCH in Fan Air Flow direction. Replace
FRU with fan air flows in the same direction.
• For a power supply: WARNING, Brocade ICX 6650, MISMATCH in PSU Air Flow direction. Replace
PSU with air flows in the same direction
You can use external labels as a guide. The power supplies and fan assemblies are labeled with an
airflow symbol on the faceplate to indicate whether the assembly takes in or exhausts air. The symbol
also appears on the top of the FRU. All FRUs in a chassis must have the same label affixed so that
airflow direction is consistent.
FIGURE 25 Examples of airflow symbols
The green E symbol indicates an exhaust FRU. This unit pulls air in from the front of the switch and
exhausts it out the rear side. This is called front-to-back airflow or forward airflow.
The orange I symbol indicates an intake FRU. This unit pulls air in from the rear side of the switch and
exhausts it out the front side. This is called back-to-front airflow or reverse airflow.
60
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Replacing a power supply unit
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or an
orange arrow with an "I."
The show chassis command displays a device’s airflow direction: Front-to-Back or Back-to-Front.
Replacing a power supply unit
CAUTION
Remove the power cord from a power supply before you install it in or remove it from the device.
Otherwise, the power supply or the device could be damaged as a result. (The device can be
running while a power supply is being installed or removed, but the power supply itself should
not be connected to a power source.)
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or an
orange arrow with an "I."
NOTE
Maintain all power supply and fan assemblies in operational condition to provide redundancy.
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
CAUTION
Changes or modifications made to this device that are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
The following table describes the Brocade ICX 6650 power supply status LED colors, behaviors, and
actions required, if any.
TABLE 12 Power supply status LED behavior, description, and required actions
LED color and behavior Description
Action required
Off (no light)
Power supply is not receiving power.
Verify that the power supply is on and seated
and the power cord is connected to a
functioning power source.
Steady green
Power supply is operating normally.
No action is required.
Steady amber
Power supply cable is disconnected or
the power supply has failed.
Check the power cable connection.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Replace the power supply
61
Determining the need to replace a power supply
Determining the need to replace a power supply
Use one of the following methods to determine the status of the power supplies:
• Check the power supply status LED (refer to Replacing a power supply unit on page 61).
• Enter the show chassis command at the prompt to display power supply status.
Time and items required
Replacing a power supply in the Brocade ICX 6650 should take less than two minutes to complete.
You need the following items to replace a power supply in a Brocade ICX 6650:
• A new power supply (must have the same part number and the same airflow label as the power
supply being replaced)
• A #1 Phillips screwdriver
Replacing a power supply
Complete the following steps to replace a power supply in a Brocade ICX 6650.
NOTE
To display power supply status, you can enter the show chassis command at the command line
prompt.
1. To leave the Brocade ICX 6650 in service while replacing a power supply, verify that the other
power supply (the one not being replaced) has been powered on for at least four seconds and has a
steady green status LED.
2. Before opening the package that contains the power supply, touch the bag to the switch casing to
discharge any potential static electricity. Brocade recommends using an ESD wrist strap during
installation.
3. Remove the power supply from the anti-static shielded bag.
4. Ensure that the replacement power supply has the same part number and airflow label as the power
supply being replaced.
5. Unplug the power cord from the power supply that is being replaced.
6. Using the Phillips screwdriver, unscrew the two captive screws on the power supply.
7. Remove the power supply from the chassis by pulling the handle on the power supply out and away
from the chassis.
8. Holding the power supply level, guide it into the carrier rails on each side and gently push it all the
way into the slot, ensuring that it firmly engages with the connector.
CAUTION
Carefully follow the mechanical guides on each side of the power supply slot and make sure
the power supply is properly inserted in the guides. Never insert the power supply upside
down.
9. When you are sure the power supply has properly engaged the connector, tighten the retainer
screws to secure the power supply in the slot.
10.Plug the power cord into the power supply to power on the unit.
62
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Replacing fan trays
The power supply will immediately attempt to power up.
11.Verify that the LED on the new power supply displays steady green while the Brocade ICX 6650 is
operating (refer to Replacing a power supply unit on page 61). If the LED is not steady green, ensure
that the power supply is securely installed and seated properly.
Replacing fan trays
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or an
orange arrow with an "I."
Orderable Brocade ICX 6650 models include two redundant, hot-swappable fan units. However, it can
run on one power supply and one fan. In that case, the empty power supply and fan slots must be
covered using the filler panels.
NOTE
Maintain all power supply and fan assemblies in operational condition to provide redundancy.
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
CAUTION
Changes or modifications made to this device that are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Determining the need to replace a fan assembly
Enter the show chassis command in the command line interface to display fan status.
Time and items required
Replacing a fan assembly in the Brocade ICX 6650 should take less than two minutes to complete.
You need the following items to replace a fan assembly in the Brocade ICX 6650 switch:
• A new fan assembly (must have the same part number and the same airflow label as the fan
assembly being replaced; refer to FRU removal and replacement procedures on page 60 for the
location of the airflow label)
• A #1 Phillips screwdriver
Installing or replacing the fan assembly
Complete the following steps to install or replace a fan assembly in a Brocade ICX 6650.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
63
Managing the Brocade ICX 6650
1. If replacing a fan assembly:
a)
b)
c)
Using a Phillips screwdriver, unscrew the captive screw on the fan assembly.
Remove the fan assembly from the chassis by pulling the handle on the fan assembly out
and away from the chassis.
Ensure that the replacement fan assembly has the same part number and airflow label as
the fan assembly being replaced.
2. If installing a new fan assembly into a slot covered with a filler panel:
a)
b)
Using a Phillips screwdriver, unscrew the captive screw on the filler panel.
Remove the filler panel.
3. Before opening the package that contains the new fan tray, touch the bag to the switch casing to
discharge any potential static electricity. It is recommended that you wear an ESD wrist strap during
installation.
4. Remove the fan tray from the anti-static shielded bag.
CAUTION
Do not force the installation. If the fan assembly does not slide in easily, ensure that it is
correctly oriented before continuing.
5. Holding the fan tray level, guide it into the carrier rails on each side and gently push it all the way
into the slot, ensuring that it firmly engages with the connector.
6. When you are sure the fan tray has properly engaged the connector, tighten the captive screw to
secure the fan tray in the slot.
NOTE
The fans are controlled automatically by the device .
7. Verify correct installation by running the show chassis command, as shown in the following
example:
device#show chassis
The stack unit 1 chassis info:
Power supply 1 (AC - Regular) present, status ok
Model Number: 23-0000144-01
Serial Number: 028
Firmware Ver: A
Power supply 1 Fan Air Flow Direction: Front to Back
Power supply 2 not present
Fan 1 ok, speed (auto): [[1]]<->2
Fan 2 ok, speed (auto): [[1]]<->2
Fan controlled temperature: 37.5 deg-C
Fan speed switching temperature thresholds:
Speed 1: NM<----->70 deg-C
Speed 2: 65<-----> 85 deg-C (shutdown)
Fan 1 Air Flow Direction: Front to Back
Fan 2 Air Flow Direction: Front to Back
MAC-Back Temperature Readings:
Current temperature : 37.5 deg-C
MAC-Left Temperature Readings:
Current temperature : 34.0 deg-C
MAC-Right Temperature Readings:
Current temperature : 33.0 deg-C
MAC-Front Temperature Readings:
Current temperature : 33.0 deg-C
CPU Temperature Readings:
Current temperature : 37.5 deg-C
Center Temperature Readings:
Current temperature : 30.5 deg-C
sensor A Temperature Readings:
Current temperature : 37.5 deg-C
sensor B Temperature Readings:
64
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Managing the Brocade ICX 6650
Current temperature :
sensor C Temperature Readings:
Current temperature :
sensor D Temperature Readings:
Current temperature :
Warning level.......:
Shutdown level......:
Boot Prom MAC : 748e.f893.eabe
Management MAC: 748e.f893.eabe
31.0 deg-C
34.5 deg-C
30.5 deg-C
45.0 deg-C
85.0 deg-C
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
65
Installing or replacing the fan assembly
66
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Specifications
● Weight and physical dimensions.....................................................................................67
● Environmental considerations......................................................................................... 67
● Cooling system and fans.................................................................................................68
● Power supply specifications............................................................................................ 70
● General specifications for Brocade ICX 6650................................................................. 72
● Supported media types................................................................................................... 72
● Pinouts and signaling...................................................................................................... 72
● Memory specifications.....................................................................................................72
● Regulatory compliance....................................................................................................73
Weight and physical dimensions
The following table lists the weight and dimensions of the Brocade ICX 6650.
TABLE 13 Physical specifications
Dimension
Value
Height
44 mm (1.73 in)
Depth
406.4 mm (16.00 in)
Width
429 mm (16.88 in)
Weight (with all power supplies and fan assemblies, and no transceivers installed)
8.41 kg (18.5 lb)
Environmental considerations
The following table lists the acceptable environmental ranges for both operating and nonoperating (such
as during transportation or storage) conditions.
TABLE 14 Environmental requirements
Condition
Acceptable during operation
Acceptable during non-operation
Ambient Temperature 0º to 40ºC (32º to 104ºF)
-25º to 70ºC (-23º to 158ºF)
Humidity
5% to 80% RH non-condensing, at 70ºC
(158ºF)
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
10% to 95% RH non-condensing, at 40ºC
(104ºF)
67
Cooling system and fans
TABLE 14 Environmental requirements (Continued)
Condition
Acceptable during operation
Acceptable during non-operation
Altitude
0 to 3 km (9,842 feet) above sea level
0 to 12 km (39,370 feet) above sea level
Shock
20 G, 6 ms, half-sine wave
33 G, 11 ms, half-sine wave, 3/eg Axis
Vibration
0.5 G sine, 0.4 gms random, 5-500 Hz
2.0 G sine, 1.1 gms random, 5-500 Hz
Airflow
Maximum - 90.1 cmh (53 cfm)Nominal - 59.5
cmh (35 cfm)
N/A
Heat dissipation
478 BTU/hr
N/A
Operating noise
46.7 dB
N/A
Cooling system and fans
The fans cool the CPU, main memory, and voltage regulators. For Brocade ICX 6650 switches, the
fans use either:
• An exhaust airflow which moves air from front to back. Refer to the first figure below. Devices with
exhaust airflow are labeled with a green arrow with an “E.”
• An intake airflow which moves air from back to front. Refer to the third figure below. Devices with
intake airflow are labeled with an orange arrow with an “I.”
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or
an orange arrow with an "I."
68
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Specifications
FIGURE 26 Brocade ICX 6650 airflow—front to back (with E-labeled power supply and fan tray)
1. Intake
2. Exhaust
FIGURE 27 Exhaust airflow label
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
69
Power supply specifications
FIGURE 28 Brocade ICX 6650 airflow—back to front (with I-labeled power supply and fan tray)
1. Intake
2. Exhaust
FIGURE 29 Intake airflow label
For a complete list of regulatory compliances, refer to Cooling system and fans.
Power supply specifications
All units ship with two RPS15 redundant, load sharing, and hot-swappable power supplies. The power
supplies are universal and capable of functioning worldwide without voltage jumpers or switches. They
meet IEC 61000-4-5 surge voltage requirements and are autoranging in terms of accommodating input
voltages and line frequencies.
The following table lists the power state definitions for the Brocade ICX 6650.
70
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Specifications
TABLE 15 Power state definitions
Power state Definition
Idle
All ports down, no optics or cables connected.
Typical
56x10 GbE, 4x40 GbE, and 4x4x10 GbE ports linked and up. 10% traffic with 64-byte packets. Fans
at normal speed.
Maximum
All ports connected with optics to draw maximum power per MSA Optics Specification. Traffic at full
rate or 100% throughput. Fans at full speed.
The following table lists the power supply specifications for the AC power draw for the Brocade ICX
6650.
TABLE 16 AC power supply system power specifications
AC voltage
Input watts
BTU/hr
Power state
100-120 VAC
114.6
391.14
Idle
100-120 VAC
154.6
527.66
Typical Light Load
100-120 VAC
171.6
585.68
Typical Full Load
100-120 VAC
230
785.01
Maximum
Inrush current should be limited to a 35A peak for any initial current surge or spike of 10 ms or less at
either cold or warm start. Any additional inrush current surges or spikes in the form of AC cycles or
multiple AC cycles greater than 10 ms and less than 150 ms must not exceed a 25A peak. After 150
ms, the AC input current will be less than the rating of input fuses and the other components within the
power supply.
The following table lists the power supply specifications for the DC power draw for the Brocade ICX
6650.
TABLE 17 DC power supply system power specifications
DC voltage
Input watts
BTU/hr
Power state
40-60 VDC
114.6
391.14
Idle
40-60 VDC
154.6
527.66
Typical Light Load
40-60 VDC
171.6
585.68
Typical Full Load
40-60 VDC
230
785.01
Maximum
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
71
General specifications for Brocade ICX 6650
General specifications for Brocade ICX 6650
The following table lists the general specifications for the Brocade ICX 6650.
TABLE 18 General specifications
Specification
Description
System architecture
Nonblocking shared-memory switch
System processor
800 MHz PowerPC
Switch bandwidth
1600 Gbps
Forwarding bandwidth (data rate, full duplex)
1190 Mpps
Supported media types
For a list of supported media types, refer to the Brocade Optics Family Data Sheet.
Pinouts and signaling
Pinout information for the rear panel mini-USB console connector is provided in the following table.
TABLE 19 Mini-USB serial management port pinouts
Pin number
Definition
Notes
1
+5V
Not used
2
RS-232 RX
Console receive
3
RS-232 TX
Console transmit
4
IN
Not used
5
GND
Ground
Memory specifications
The Brocade ICX 6650 has two types of memory devices: boot flash and main memory. The size of
each is listed in the following table.
72
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Regulatory compliance
TABLE 20 Brocade ICX 6650 memory specifications
Type
Size
Boot flash
64 MB NOR flash
Main memory - DDR2-400 SDRAM with ECC (RDIMM)
1 GB
Regulatory compliance
The following table lists the Electromagnetic Compatibility (EMC), Immunity standards, and safety
agency approvals for the FastIron family of switches.
TABLE 21 Regulatory compliance and safety approvals
Certifications
Electromagnetic:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
FCC Part 15, Subpart B, Class A
ICES-003: 2004
VCCI-Technical Requirement (V-3/2011.04)/Class A
EN 55022: 2006+A1: 2007 Class A
EN 61000-3-2: 2006+A1: 2009+A2: 2009 Class A
EN 61000-3-3: 2008
EN 61000-6-1: 2007
EN 61000-6-3: 2007
EN 55024: 1998+A1: 2001+A2: 2003
EN 300 386 (V1.4.1): 2008
IEC 61000-4-2: 2008 ED. 2.0
IEC 61000-4-3: 2006+A1: 2007+A2: 2010 ED. 3.2
IEC 61000-4-4: 2004+A1: 2010 ED. 2.0
IEC 61000-4-5: 2005 ED. 2.0
IEC 61000-4-6: 2008 ED. 3.0
IEC 61000-4-8: 2009 ED. 2.0
IEC 61000-4-11: 2004 ED. 2.0
Environmental:
•
RoHS-compliant (6 of 6); WEEE-compliant
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
73
Regulatory compliance
74
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Regulatory Statements
● BSMI statement (Taiwan)................................................................................................75
● Canadian requirements...................................................................................................75
● China CC statement........................................................................................................76
● China ROHS................................................................................................................... 76
● Europe and Australia (CISPR 22 Class A Warning)....................................................... 77
● FCC warning (US only)................................................................................................... 77
● Germany......................................................................................................................... 77
● KCC statement (Republic of Korea)................................................................................77
● VCCI statement...............................................................................................................77
BSMI statement (Taiwan)
Warning:
This is Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Canadian requirements
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations, ICES-003 Class A.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
75
China CC statement
China CC statement
China ROHS
Refer to the latest revision of the China ROHS document (P/N 53‐1000428‐xx) which ships with the
product.
76
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Europe and Australia (CISPR 22 Class A Warning)
Europe and Australia (CISPR 22 Class A Warning)
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
FCC warning (US only)
This equipment has been tested and complies with the limits for a Class A computing device pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used
in accordance with the instruction manual, might cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at the user’s own expense.
Germany
Machine noise information regulation - 3. GPSGV, the highest sound pressure level value is 53.0 dB(A)
in accordance with EN ISO 7779.
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel beträgt 53.0 dB(A)
gemäss EN ISO 7779.
KCC statement (Republic of Korea)
Class A device (Broadcasting Communication Device for Office Use): This device obtained EMC
registration for office use (Class A), and may be used in places other than home. Sellers and/or users
need to take note of this.
VCCI statement
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
77
Brocade ICX 6650 Regulatory Statements
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance might arise. When such trouble occurs, the user might be required to take corrective
actions.
78
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Cautions and Danger Notices
● Cautions.......................................................................................................................... 79
● Danger Notices............................................................................................................... 84
Cautions
A Caution statement alerts you to situations that can be potentially hazardous to you or cause damage
to hardware, firmware, software, or data.
Ein Vorsichthinweis warnt Sie vor potenziellen Personengefahren oder Beschädigung der Hardware,
Firmware, Software oder auch vor einem möglichen Datenverlust
Un message de mise en garde vous alerte sur des situations pouvant présenter un risque potentiel de
dommages corporels ou de dommages matériels, logiciels ou de perte de données.
Un mensaje de precaución le alerta de situaciones que pueden resultar peligrosas para usted o causar
daños en el hardware, el firmware, el software o los datos.
General cautions
CAUTION
Do not install the device in an environment where the operating ambient temperature might
exceed 40°C (104°F).
VORSICHT
Das Gerät darf nicht in einer Umgebung mit einer Umgebungsbetriebstemperatur von über
40°C (104°F) installiert werden.
MISE EN
GARDE
N'installez pas le dispositif dans un environnement où la température d'exploitation ambiante
risque de dépasser 40°C (104°F).
PRECAUCIÓN
No instale el instrumento en un entorno en el que la temperatura ambiente de operación pueda
exceder los 40°C (104°F).
CAUTION
Make sure the airflow around the front, sides, and back of the device is not restricted.
VORSICHT
Stellen Sie sicher, dass an der Vorderseite, den Seiten und an der Rückseite der Luftstrom
nicht behindert wird.
MISE EN
GARDE
Vérifiez que rien ne restreint la circulation d'air devant, derrière et sur les côtés du dispositif et
qu'elle peut se faire librement.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
79
Brocade ICX 6650 Cautions and Danger Notices
PRECAUCIÓN
Asegúrese de que el flujo de aire en las inmediaciones de las partes anterior, laterales y
posterior del instrumento no esté restringido.
CAUTION
Never leave tools inside the chassis.
VORSICHT
Never leave tools inside the chassis.
MISE EN
GARDE
Ne laissez jamais d'outils à l'intérieur du châssis
PRECAUCIÓN
No deje nunca herramientas en el interior del chasis.
CAUTION
Changes or modifications made to this device that are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
VORSICHT
Falls dieses Gerät verändert oder modifiziert wird, ohne die ausdrückliche Genehmigung der
für die Einhaltung der Anforderungen verantwortlichen Partei einzuholen, kann dem Benutzer
der weitere Betrieb des Gerätes untersagt werden.
MISE EN
GARDE
Les éventuelles modifications apportées à cet équipement sans avoir été expressément
approuvées par la partie responsable d'en évaluer la conformité sont susceptibles d'annuler le
droit de l'utilisateur à utiliser cet équipement.
PRECAUCIÓN
Si se realizan cambios o modificaciones en este dispositivo sin la autorización expresa de la
parte responsable del cumplimiento de las normas, la licencia del usuario para operar este
equipo puede quedar anulada.
CAUTION
Ensure that adequate ventilation is provided for the system. A 3 cm clearance is recommended
above the device and 8 cm clearance is recommended on each side.
80
VORSICHT
Stellen Sie sicher, dass das System ausreichend belüftet wird. Über dem Gerät wird 3 cm
Freiraum, auf beiden Seiten jeweils 8 cm Freiraum empfohlen.
MISE EN
GARDE
Assurez-vous que le circuit est correctement ventilé. Il est recommandé de conserver un
espace de 3 cm au-dessus du dispositif, et de 8 cm sur chaque côté.
PRECAUCIÓN
Asegúrese de proporcionar una ventilación adecuada al sistema. Se recomienda dejar 3 cm
de espacio libre por encima del dispositivo y 8 cm a cada lado.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Cautions and Danger Notices
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or an
orange arrow with an "I."
VORSICHT
Vergewissern Sie sich, dass die Luftstromrichtung des Netzteils der eingebauten Lüftereinheit
entspricht. Die Netzteile und Lüftereinheiten sind eindeutig mit einem grünen Pfeil und dem
Buchstaben "E" oder einem orangefarbenen Pfeil mit dem Buchstaben "I" gekennzeichnet.
MISE EN
GARDE
Veillez à ce que le sens de circulation de l'air du bloc d'alimentation corresponde à celui du
tiroir de ventilation installé. Les blocs d'alimentation et les tiroirs de ventilation sont étiquetés
d'une flèche verte avec un "E " ou d'une flèche orange avec un " I ".
PRECAUCIÓN
Asegúrese de que la dirección del flujo de aire de la unidad de alimentación se corresponda
con la de la bandeja del ventilador instalada. Los dispositivos de alimentación y las bandejas
del ventilador están etiquetadas claramente con una flecha verde y una "E" o con una flecha
naranja y una "I".
CAUTION
Use the erase startup-config command only for new systems. If you enter this command on a
system you have already configured, the command erases the configuration. If you accidentally
do erase the configuration on a configured system, enter the write memory command to save
the running configuration to the startup-config file.
VORSICHT
Verwenden Sie den Befehl "Erase startup-config " (Löschen Startup-Konfig) nur für neue
Systeme. Wenn Sie diesen Befehl in ein bereits konfiguriertes System eingeben, löscht der
Befehl die Konfiguration. Falls Sie aus Versehen die Konfiguration eines bereits konfigurierten
Systems löschen, geben Sie den Befehl "Write Memory " (Speicher schreiben) ein, um die
laufende Konfiguration in der Startup-Konfig-Datei zu speichern.
MISE EN
GARDE
N'utilisez la commande erase startup-config que pour les nouveaux systèmes. Si vous entrez
cette commande sur un système que vous avez déjà configuré, elle efface la configuration. Si
vous effacez la configuration par accident sur un système configuré, entrez la commande write
memory pour enregistrer la configuration actuelle dans le fichier startup-config.
PRECAUCIÓN
Use el comando erase startup-config (borrar configuración de inicio) para sistemas nuevos
solamente. Si usted introduce este comando en un sistema que ya ha configurado, el comando
borrará la configuración. Si usted borra accidentalmente la configuración en un sistema ya
configurado, introduzca el comando write memory (escribir memoria) para guardar la
configuración en ejecución en el archivo startup-config.
Electrical cautions
CAUTION
Use a separate branch circuit for each power cord, which provides redundancy in case one of
the circuits fails.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
81
Brocade ICX 6650 Cautions and Danger Notices
VORSICHT
Es empfiehlt sich die Installation eines separaten Stromkreiszweiges für jede Elektroschnur
als Redundanz im Fall des Ausfalls eines Stromkreises.
MISE EN
GARDE
Utilisez un circuit de dérivation différent pour chaque cordon d’alimentation ainsi, il y aura un
circuit redondant en cas de panne d’un des circuits.
PRECAUCIÓN
Use un circuito derivado separado para cada cordón de alimentación, con lo que se
proporcionará redundancia en caso de que uno de los circuitos falle.
CAUTION
Ensure that the device does not overload the power circuits, wiring, and over-current
protection. To determine the possibility of overloading the supply circuits, add the ampere
(amp) ratings of all devices installed on the same circuit as the device. Compare this total with
the rating limit for the circuit. The maximum ampere ratings are usually printed on the devices
near the input power connectors.
VORSICHT
Stromkreise, Verdrahtung und Überlastschutz dürfen nicht durch das Gerät überbelastet
werden. Addieren Sie die Nennstromleistung (in Ampere) aller Geräte, die am selben
Stromkreis wie das Gerät installiert sind. Somit können Sie feststellen, ob die Gefahr einer
Überbelastung der Versorgungsstromkreise vorliegt. Vergleichen Sie diese Summe mit der
Nennstromgrenze des Stromkreises. Die Höchstnennströme (in Ampere) stehen
normalerweise auf der Geräterückseite neben den Eingangsstromanschlüssen.
MISE EN
GARDE
Assurez-vous que le dispositif ne risque pas de surcharger les circuits d'alimentation, le
câblage et la protection de surintensité. Pour déterminer le risque de surcharge des circuits
d'alimentation, additionnez l'intensité nominale (ampères) de tous les dispositifs installés sur le
même circuit que le dispositif en question. Comparez alors ce total avec la limite de charge du
circuit. L'intensité nominale maximum en ampères est généralement imprimée sur chaque
dispositif près des connecteurs d'entrée d'alimentation.
PRECAUCIÓN
Verifique que el instrumento no sobrecargue los circuitos de corriente, el cableado y la
protección para sobrecargas. Para determinar la posibilidad de sobrecarga en los circuitos de
suministros, añada las capacidades nominales de corriente (amp) de todos los instrumentos
instalados en el mismo circuito que el instrumento. Compare esta suma con el límite nominal
para el circuito. Las capacidades nominales de corriente máximas están generalmente
impresas en los instrumentos, cerca de los conectores de corriente de entrada.
CAUTION
Before plugging a cable into to any port, be sure to discharge the voltage stored on the cable
by touching the electrical contacts to ground surface.
82
VORSICHT
Bevor Sie ein Kabel in einen Anschluss einstecken, entladen Sie jegliche im Kabel
vorhandene elektrische Spannung, indem Sie mit den elektrischen Kontakten eine geerdete
Oberfläche berühren.
MISE EN
GARDE
Avant de brancher un câble à un port, assurez-vous de décharger la tension du câble en
reliant les contacts électriques à la terre.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Cautions and Danger Notices
PRECAUCIÓN
Antes de conectar un cable en cualquier puerto, asegúrese de descargar la tensión
acumulada en el cable tocando la superficie de conexión a tierra con los contactos eléctricos.
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
VORSICHT
Falls kein Modul oder Netzteil im Steckplatz installiert wird, muss die Steckplatztafel angebracht
werden. Wenn ein Steckplatz nicht abgedeckt wird, läuft das System heiß.
MISE EN
GARDE
Si vous n’installez pas de module ou de bloc d'alimentation dans un slot, vous devez laisser le
panneau du slot en place. Si vous faites fonctionner le châssis avec un slot découvert, le
système surchauffera.
PRECAUCIÓN
Si no instala un módulo o un fuente de alimentación en la ranura, deberá mantener el panel de
ranuras en su lugar. Si pone en funcionamiento el chasis con una ranura descubierta, el
sistema sufrirá sobrecalentamiento.
CAUTION
For the DC input circuit to the system, make sure there is a 20 Amp circuit breaker, minimum 60
VDC, double pole, on the input terminal block to the power supply. The input wiring for
connection to the product should be copper wire, 12 AWG, marked VW-1, and rated minimum
90°C.
VORSICHT
Für den Eingangs-Gleichstromkreis zum System ist ein 20 A (Minimum), -60 V DC, doppelpolig,
am Eingang zur Reihenklemme zu installieren. Bei der Eingangsverdrahtung zum Anschluss
des Produkts sollte es sich um einen 12 AWG-Kupferdraht (VW-1) und einer
Mindestnenntemperatur von 90° C handeln.
MISE EN
GARDE
Pour le circuit d'alimentation C.C du système, assurez-vous de la présence d'un disjoncteur de
20 ampères, minimum -60 V C.C., double coupure, sur l'entrée vers le bloc d'alimentation. Les
câbles d'alimentation pour le produit doivent être en fils de cuivre, 12 AWG (American Wire
Gauge), marqués VW-1 et classés 90 degrés Celsius.
PRECAUCIÓN
Pour le circuit d'alimentation C.C du système, assurez-vous de la présence d'un disjoncteur de
20 ampères, minimum -60 V C.C., double coupure, sur l'entrée vers le bloc d'alimentation. Les
câbles d'alimentation pour le produit doivent être en fils de cuivre, 12 AWG (American Wire
Gauge), marqués VW-1 et classés 90 degrés Celsius.
CAUTION
Carefully follow the mechanical guides on each side of the power supply slot and make sure the
power supply is properly inserted in the guides. Never insert the power supply upside down.
VORSICHT
Beachten Sie mechanischen Führungen an jeder Seite des Netzteils, das ordnungegemäß in
die Führungen gesteckt werden muss. Das Netzteil darf niemals umgedreht eingesteckt
werden.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
83
Danger Notices
MISE EN
GARDE
Suivez attentivement les repères mécaniques de chaque côté du slot du bloc d'alimentation et
assurez-vous que le bloc d'alimentation est bien inséré dans les repères. N'insérez jamais le
bloc d'alimentation à l'envers.
PRECAUCIÓN
Siga cuidadosamente las guías mecánicas de cada lado de la ranura del suministro de energía
y verifique que el suministro de energía está insertado correctamente en las guías. No inserte
nunca el suministro de energía de manera invertida.
CAUTION
Remove the power cord from a power supply before you install it in or remove it from the
device. Otherwise, the power supply or the device could be damaged as a result. (The device
can be running while a power supply is being installed or removed, but the power supply itself
should not be connected to a power source.)
VORSICHT
Nehmen Sie vor dem Anschließen oder Abtrennen des Geräts das Stromkabel vom Netzteil
ab. Ansonsten könnten das Netzteil oder das Gerät beschädigt werden. (Das Gerät kann
während des Anschließens oder Annehmens des Netzteils laufen. Nur das Netzteil sollte nicht
an eine Stromquelle angeschlossen sein.)
MISE EN
GARDE
Enlevez le cordon d'alimentation d'un bloc d'alimentation avant de l'installer ou de l'enlever du
dispositif. Sinon, le bloc d'alimentation ou le dispositif risque d'être endommagé. (Le
dispositive peut être en train de fonctionner lorsque vous installez ou enlevez un bloc
d'alimentation, mais le bloc d'alimentation lui-même ne doit pas être connecté à une source
d'alimentation.)
PRECAUCIÓN
Retire el cordón de corriente del suministro de corriente antes de instalarlo o retírarlo del
instrumento. De no hacerse así, el suministro de corriente o el instrumento podrían resultar
dañados. (El instrumento puede estar encendido mientras se instala o retira un suministro de
corriente, pero el suministro de corriente en sí no deberá conectado a la corriente).
Danger Notices
A Danger statement indicates conditions or situations that can be potentially lethal or extremely
hazardous to you. Safety labels are also attached directly to products to warn of these conditions or
situations.
Ein Gefahrenhinweis warnt vor Bedingungen oder Situationen die tödlich sein können oder Sie extrem
gefährden können. Sicherheitsetiketten sind direkt auf den jeweiligen Produkten angebracht um vor
diesen Bedingungen und Situationen zu warnen.
Un paragraphe Danger indique des conditions ou des situations potentiellement mortelles ou
extrêmement dangereuses. Des labels de sécurité sont posés directement sur le produit et vous
avertissent de ces conditions ou situations
Una advertencia de peligro indica condiciones o situaciones que pueden resultar potencialmente
letales o extremadamente peligrosas. También habrá etiquetas de seguridad pegadas directamente
sobre los productos para advertir de estas condiciones o situaciones.
84
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Cautions and Danger Notices
General dangers
DANGER
The procedures in this manual are for qualified service personnel.
GEFAHR
Die Vorgehensweisen in diesem Handbuch sind für qualifiziertes Servicepersonal bestimmt.
DANGER
Les procédures décrites dans ce manuel doivent être effectuées par un personnel de
maintenance qualifié.
PELIGRO
Los procedimientos de este manual deben llevarlos a cabo técnicos cualificados.
DANGER
Be careful not to accidently insert your fingers into the fan tray while removing it from the
chassis. The fan may still be spinning at a high speed.
GEFAHR
Die Finger dürfen nicht versehentlich in das Ventilatorblech gesteckt werden, wenn dieses vom
Gehäuse abgenommen wird. Der Ventilator kann sich unter Umständen noch mit hoher
Geschwindigkeit drehen.
DANGER
Faites attention de ne pas accidentellement insérer vos doigts dans le boîtier du ventilateur
lorsque vous l'enlevez du châssis. Il est possible que le ventilateur tourne encore à grande
vitesse
PELIGRO
Procure no insertar los dedos accidentalmente en la bandeja del ventilador cuando esté
desmontando el chasis. El ventilador podría estar girando a gran velocidad.
Electrical dangers
DANGER
Before beginning the installation, see the precautions in “Power precautions.”
GEFAHR
Vor der Installation siehe Vorsichtsmaßnahmen unter “Power Precautions”
(Vorsichtsmaßnahmen in Bezug auf elektrische Ablagen).
DANGER
Avant de commencer l'installation, consultez les précautions décrites dans “Power Precautions”
(Précautions quant à l'alimentation).
PELIGRO
Antes de comenzar la instalación, consulte las precauciones en la sección “Power Precautions”
(Precauciones sobre corriente).
DANGER
Disconnect the power cord from all power sources to completely remove power from the device.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
85
Brocade ICX 6650 Cautions and Danger Notices
GEFAHR
Ziehen Sie das Stromkabel aus allen Stromquellen, um sicherzustellen, dass dem Gerät kein
Strom zugeführt wird.
DANGER
Débranchez le cordon d'alimentation de toutes les sources d'alimentation pour couper
complètement l'alimentation du dispositif.
PELIGRO
Para desconectar completamente la corriente del instrumento, desconecte el cordón de
corriente de todas las fuentes de corriente.
DANGER
If the installation requires a different power cord than the one supplied with the device, make
sure you use a power cord displaying the mark of the safety agency that defines the
regulations for power cords in your country. The mark is your assurance that the power cord
can be used safely with the device.
GEFAHR
Falls für die Installation ein anderes Stromkabel erforderlich ist (wenn das mit dem Gerät
gelieferte Kabel nicht passt), müssen Sie sicherstellen, dass Sie ein Stromkabel mit dem
Siegel einer Sicherheitsbehörde verwenden, die für die Zertifizierung von Stromkabeln in
Ihrem Land zuständig ist. Das Siegel ist Ihre Garantie, dass das Stromkabel sicher mit Ihrem
Gerät verwendet werden kann.
DANGER
Si l'installation nécessite un cordon d'alimentation autre que celui fourni avec le dispositif,
assurez-vous d'utiliser un cordon d'alimentation portant la marque de l'organisation
responsable de la sécurité qui définit les normes et régulations pour les cordons d'alimentation
dans votre pays. Cette marque vous assure que vous pouvez utiliser le cordon d'alimentation
avec le dispositif en toute sécurité.
PELIGRO
Si la instalación requiere un cordón de corriente distinto al que se ha suministrado con el
instrumento, verifique que usa un cordón de corriente que venga con la marca de la agencia
de seguridad que defina las regulaciones para cordones de corriente en su país. Esta marca
será su garantía de que el cordón de corriente puede ser utilizado con seguridad con el
instrumento.
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
GEFAHR
Aus Sicherheitsgründen sollte ein EGB-Armband zum Schutz von elektronischen gefährdeten
Bauelementen mit einem 1 Megaohm-Reihenwiderstand ausgestattet sein.
DANGER
Pour des raisons de sécurité, la dragonne ESD doit contenir une résistance de série 1 méga
ohm.
PELIGRO
Por razones de seguridad, la correa de muñeca ESD deberá contener un resistor en serie de
1 mega ohmio.
DANGER
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
86
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Brocade ICX 6650 Cautions and Danger Notices
GEFAHR
Es besteht Explosionsgefahr, wenn ein unzulässiger Batterietyp eingesetzt wird.
Verbrauchte Batterien sind entsprechend den geltenden Vorschriften zu entsorgen.
DANGER
Risque d'explosion en cas de remplacement de la pile par un modèle incorrect.
Débarrassez-vous des piles usagées conformément aux instructions.
PELIGRO
Riesgo de explosión si se sustituye la batería por una de tipo incorrecto.
Deshágase de las baterías usadas de acuerdo con las instrucciones.
DANGER
To avoid high voltage shock, do not open the device while the power is on.
GEFAHR
Das eingeschaltete Gerät darf nicht geöffnet werden, da andernfalls das Risiko eines
Stromschlags mit Hochspannung besteht.
DANGER
Afin d'éviter tout choc électrique, n'ouvrez pas l'appareil lorsqu'il est sous tension.
PELIGRO
Para evitar una descarga de alto voltaje, no abra el dispositivo mientras esté encendido.
Dangers related to equipment weight
DANGER
Make sure the rack housing the device is adequately secured to prevent it from becoming
unstable or falling over.
GEFAHR
Stellen Sie sicher, dass das Gestell für die Unterbringung des Geräts auf angemessene Weise
gesichert ist, so dass das Gestell oder der Schrank nicht wackeln oder umfallen kann.
DANGER
Vérifiez que le bâti abritant le dispositif est bien fixé afin qu'il ne devienne pas instable ou qu'il
ne risque pas de tomber.
PELIGRO
Verifique que el bastidor que alberga el instrumento está asegurado correctamente para evitar
que pueda hacerse inestable o que caiga.
DANGER
Mount the devices you install in a rack as low as possible. Place the heaviest device at the
bottom and progressively place lighter devices above.
GEFAHR
Montieren Sie die Geräte im Gestell so tief wie möglich. Platzieren Sie das schwerste Gerät
ganz unten, während leichtere Geräte je nach Gewicht (je schwerer desto tiefer) darüber
untergebracht werden.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
87
Brocade ICX 6650 Cautions and Danger Notices
DANGER
Montez les dispositifs que vous installez dans un bâti aussi bas que possible. Placez le
dispositif le plus lourd en bas et le plus léger en haut, en plaçant tous les dispositifs
progressivement de bas en haut du plus lourd au plus léger.
PELIGRO
Monte los instrumentos que instale en un bastidor lo más bajos posible. Ponga el instrumento
más pesado en la parte inferior y los instrumentos progresivamente más livianos más arriba.
Laser dangers
DANGER
All fiber-optic interfaces use Class 1 lasers.
88
GEFAHR
Alle Glasfaser-Schnittstellen verwenden Laser der Klasse 1.
DANGER
Toutes les interfaces en fibres optiques utilisent des lasers de classe 1.
PELIGRO
Todas las interfaces de fibra óptica utilizan láser de clase 1.
Brocade ICX 6650 Hardware Installation Guide
53-1003398-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising