ifs de7300 7400 series install & oper instr

ifs de7300 7400 series install & oper instr
DE7300-EE
DE7300-ME
DE7300-SE
DE7300-MM
DE7300-MS
DE7300-SS
DE7300-M3
DE7300-S3
DE7400-M
DE7400-S
DE7400-MM
DE7400-SS
DE7400-MS
IFS Fiber Module
Installation & Operation
Instructions
P/N 1062841 • REV B • ISS 01OCT11
DE7300 SERIES
LOSS OF SIGNAL
Fiber Port A
LOSS OF SIGNAL
Fiber Port B
LOSS OF SIGNAL
Fiber Port C
FIBER LINK
CONTACTS
(All Optical Ports)
On
LOS A Off
CONTACT CLOSURE
FOR LOS
On
On
NO
CONTACT CLOSURE
LOS B Off
CONTACT CLOSURE
FOR LOS
LOS B
NO
CONTACT CLOSURE
LOS C Off
CONTACT CLOSURE
FOR LOS
LOS A
LOS C
NO
CONTACT CLOSURE
3
Normal Open
2
COM
1
Normal Closed
DE7300 SERIES
D
A
C
B
H
E
F
A
B
C
D
E
F
G
H
I
I
G
Fiber port A
Fiber port B
Link Speed (Channels A & B)
Simplex/Duplex (Channels A&B)
Power connection
Power
LOS A, B, C switch
Fiber link contacts connection
Port connection
GREEN = 100
RED = 10
GREEN = DUPLEX
OFF = SIMPLEX
LED illuminates with fiber connection
DE7400-S
GIGABIT ETHERNET MEDIA CONVERTER
LNK
10/100/1000TX
ACT
TX
10/100/1000TX
NO - 3
1000FX
CONTACT
CLOSURE
RX
COM - 2
NC - 1
ifs
-3
LOS - 2
-1
Inter nati onal
F i ber
Sy s tem s
Inc or por ated
OFF
POWER
POWER
-2
+12-24
VDC - 1
Multimode
fiber optic cable
DE7300-SS
3 PORT GIGABIT ETHERNET SWITCH
TX
PORT C
10/100/1000TX
B
1000FX
10/100/1000TX
RX
NO - 3
CONTACT
CLOSURE
COM - 2
NC - 1
LNK
TX
ACT
ifs
A
1000FX
RX
-3
LOS B - 2
LOS A - 1
Inter nati onal
F i ber
Sy s tem s
Inc or por ated
OFF
POWER
POWER
-2
+12-24 VDC - 1
Singlemode
fiber optic cable
DE7400-S
GIGABIT ETHERNET MEDIA CONVERTER
LNK
10/100/1000TX
ACT
TX
NO - 3
100FX
CONTACT
CLOSURE
RX
COM - 2
NC - 1
ifs
-3
LOS - 2
-1
Inter nati onal
F i ber
Sy s tem s
Inc or por ated
OFF
POWER
POWER
-2
+12-24 VDC - 1
10/100/1000TX
IF YOUR POWER OUTLET DOES NOT HAVE A CONNECTION
TO GROUND:
For proper installation the DE7100-XX stand alone units must be
attached to earth ground. Ordinarily, this is accomplished through the power
supply. If your power outlet does not have a ground prong then a wire must
be attached from the power connector to ground. Connect the green wire
included, from ground to the power connector as shown below.
GREEN WIRE
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by International Fiber Systems, Inc. could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CLASS 1 LASER PRODUCT
(For purposes of IEC 60825-1)
Complies with FDA Performance Standard for Laser Products
Title 21
Code of Federal Regulations
Subchapter J
Comprehensive
Lifetime Warranty
(a) Seller warrants to the original End User that products and any
services furnished hereunder will be free from defects in material
and workmanship as of the date of delivery, and will conform to
Seller’s published technical specifications. The foregoing shall
apply only to failures to meet said warranties which appear within
that period of time during which the Products are installed in their
original installation for the original End User and operator of such
Products; provided, however, that in the event of product discontinuance, warranty support is limited to five (5) years from the
announcement of discontinuance. Notwithstanding the preceding
sentence, the duration of the warranty period for products not
manufactured by Seller (e.g., fiber optic cabling, test equipment,
power supplies or batteries) shall be the warranty period offered by
the original manufacturer, if any.
(b) The conditions of any tests shall be mutually agreed upon and
Seller shall be notified of, and may be represented at, all tests that
may be made. The warranties and remedies set forth herein are
conditioned upon (a) proper storage, installation, use and maintenance, and conformance with any applicable recommendations of
Seller and (b) Buyer promptly notifying Seller of any defects and,
if required, promptly making the product available for correction.
(c) If any product or service fails to meet the foregoing warranties,
Seller shall thereupon correct any such failure either at its option,
(i) by repairing any defective or damaged product or parts of the
products, or (ii) by making available any necessary repaired or
replacement products or parts thereof. Any repaired or replacement
part or product shall be warranted for the remaining period of the
original Warranty Period. Seller shall pay, or credit Buyer for, the
cost of freight for all return shipments of products or parts to
Buyer. Where a failure cannot be corrected by Seller's reasonable
efforts, the parties will negotiate an equitable adjustment in price.
(d) The preceding paragraph sets forth the exclusive remedies for
claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,
all such liability shall terminate and BUYER shall have a reasonable time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the warranty
period. The foregoing warranties are exclusive and in lieu of all
other warranties, whether written, oral, implied or statutory.
NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. Seller does not warrant any
products or services of others which BUYER has designated.
Contacting us
For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any
other documentation provided. If you still have questions, contact us during business hours (Monday through
Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).
Table 3. Sales and support contact information
Sales
Phone:
Toll-free: 888.437.3287 in the US, including Alaska and Hawaii;
Puerto Rico; Canada.
Outside the toll-free area: 503.885.5700.
E-mail
Fax
Technical support
[email protected]
888.329.0331
888.329.0332
Note: Be ready at the equipment before calling.
Online
Another great resource for assistance with your Interlogix product is our online publication library. To access
the library, go to our website at the following location:
http://www.interlogix.com/transmission1
1.
Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will
need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.
Product Disassembly Instructions for WEEE
Per European Directive 2002/95/EC Waste Electrical and
Electronic Equipment
Required Tools:
One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.
For the enclosed box version:
1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.
2. Lift off box top cover.
3. Locate and remove securement screws for printed circuit board.
4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
5. Lift off printed circuit board.
6. Disassembly of box version of product is complete.
For rack version:
1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.
2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
3. Lift off printed circuit board(s).
4. Disassembly of rack card version of product is complete.
Copyright
Trademarks and
patents
Manufacturer
Certification
FCC compliance
ACMA compliance
Canada
European Union
directives
© 2011 UTC Fire & Security. All rights reserved.
Interlogix and IFS names and logos are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
N4131
Class A: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
2004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information, see www.interlogix.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement