vhs-3175q_en_manual

vhs-3175q_en_manual
EN
HEATING
WALL MOUNT QUARTZ HEATER
Model: VHS-3175Q
Instruction manual
ENGLISH
GENERAL INFORMATION
· Before carrying out any operation, read carefully the following instructions. KEEP THIS BOOKLET IN A
SAFE PLACE SO THAT YOU MAY CONSULT IT LATER.
· After removing the packaging, make sure that the appliance is in good condition. If you have doubts, do not
use the appliance and return to your retailer.
· The packaging materials contain plastic, nails, etc. which may be hazardous and therefore should not be left
within the reach of children.
ELECTRICAL CONNECTION
· Before connecting the appliance, make sure that the specifications on the data plate correspond to the
conditions of the electrical supply network.
· The electrical safety of this appliance can only be assured if it has been correctly grounded.
· This appliance conforms to the directives 89/336/CEE concerning electromagnetic interference.
WARNING
· We strongly recommend that the electrical installation be carried out by qualified professional personnel.
· Do not install the appliance in the immediate vicinity of bath tubs, showers, wash basins, swimming pools,
etc.
· This appliance is to be used only for the purpose intended by the manufacturer that is for area heating. Any
other use is improper and therefore dangerous. The manufacturer is not responsible for any damages caused by
improper and unreasonable use of this appliance.
· DO NOT PUT A COVER OVER THE APPLIANCE AS THE COVER COULD CATCH FIRE DURING
USE.
· Do not attach accessories or equipment not foreseen by the manufacturer.
· Improper installation can cause harm to persons and animals or damage to objects, for
· Install the appliance only in a horizontal position.
· Do not install the appliance under a light or fixed source of electrical supply.
· Avoid installation behind a door.
INSTALLATION
· Maintain a sufficient distance between the appliance and walls and objects. Minimum distances.
· Whenever the appliance is to be installed in a bathroom, it is necessary to maintain the required safety zone
around it.
· Do not install the appliance so that the heat rays directly bear on walls or adjacent objects.
· For fixture to a wall, proceed in the following manner:
-Unscrew by one turn the screw A which determines the inclination of the appliance.
-Turn the wall support to the end of its travel.
-Unscrew the screw which fastens the cover of the wall support and remove the cover.
-Determine the placement of the appliance and, with the help of the holes of the holes are to be drilled in the
wall.
-Drill two 6 mm holes and insert the supplied dowels.
ENGLISH
2
ELECTRICAL CONNECTION
THIS APPLIANCE MUST BE EARTHED
This is appliance is intended or a fixed installation, that is with a permanent electrical connection.
The power cord must have the power consumption.
Material: PVC
NR. 3 wires (neutral, live, earth)
Section: 1mm2 (minimum)
Sheath: 10mm (maximum diameter)
Once the power cord is inserted through the wall support, attach the support by means of the supplied screws
and dowels which were previously inserted into the wall.
Remove the screw B from the cable in the cable clamp, and place the cable in the provided seat. Make sure that
the wires connections correspond to the stamped symbols on the support.
WARNING – THIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in the mains lead are colored in accordance with the following code:
Green and yellow: Earth
Blue: Neutral
Brown: Live
The green and yellow wire must be connected to the terminal marked with the letter E or the earth symbol
The blue wire must be connected to the terminal marked with the letter N or colored black.
The brown wire must be connected to the terminal marked with the letter L.
.
Clamp the wires, to the cable holder by means of the screw B.
Put the cover back into its place on the wall support and fasten it by means of the appropriate screw.
Unscrew by one turn the screws which regulate the inclination of the appliance.
Determine the desired heating inclination and fasten the screw by means of the screws (A).
Do not change the inclination without loosening the appropriate screws. Otherwise permanent damage
could be caused to the appliance.
IMPORTANT
During the assembly is important to be especially careful to touch with the hands the heating elements as this
could leave spots which would diminish the thermal radiation.
INSTRUCTIONS FOR USE
In order to turn the appliance on, turn on the switch.
0=OFF ; 1=500W ; 2=1000W ; 3=1500W
If you notice while turning on the appliance that there are slight vibrations which then gradually fade away,
don’t become unduly alarmed. This is part of the normal behaviour of the appliance.
ENGLISH
3
MAINTENANCE
· Before undertaking any maintenance operation, disconnect the appliance from the power supply.
- This appliance does not require any particular maintenance. For cleaning it is recommended to use a soft
moist rag and neutral detergent. Do not use an abrasive cloth or devices which could effect the outward
appearance of the appliance. Check that the parts exposed to the heat rays and the ventilation are free of dust
and dirt.
During cleaning, be careful not to touch the quartz heating elements.
· In case of breakdown and/or poor function of the appliance, disconnect the appliance from the power supply
and contact an authorized service center. Always request the use of original spare parts.
The non-observation of these instructions can compromise the safety of the appliance and render guaranty
invalid.
According to Waste of Electrical and Electronic Equipment (WEEE) directive, WEEE should be
separately collected and treated. If at any time in future you need to dispose of this product please do
NOT dispose of this product with household waste. Please send this product to WEEE collecting
points where available.
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising