Casablanca | TRIDENT | Owner`s manual | Casablanca TRIDENT Owner`s manual

Casablanca TRIDENT Owner`s manual
Trident™ Owner’s Manual
Read and Save These Instructions!
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper
installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and
carefully. Retain this manual for future reference.
Caution: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box
before attempting any installation procedure.
CONTENTS
Introduction
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safe Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MOUNTING RECOMMENDATIONS
General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sloped Ceiling Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Fan Installation
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Crossbar Mounting Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Lag Screw Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Canopy Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Fan Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Blade Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hanging the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Canopy Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Canopy Hatch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Light Housing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Light Fixture Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PRIME•TOUCH® Control
Control Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Changing Transmitter Frequency Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Care Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Authorized service centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TR43001 AT1008
1
Introduction
Before You Start
• CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code,
ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician.
To avoid overheating and possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture,
motor operated appliance, or transformer-supplied appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations. If it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 2.3 amps. The fan uses about 1 amp or 100 watts. Maximum light current
is about 1.3 amps or 120 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
• WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. Do not
insert foreign objects in between the rotating fan blades.
• WARNING: to reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device. Use
only the control provided with or recommended for this fan.
Unpacking
Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts
listed in the Parts Guide. Before discarding packaging materials, be certain that all parts have been removed.
NOTE: For best performance and for your warranty to be valid, use only genuine Casablanca blades, light
fixtures, and accessories.
Safe Use
• Inspect the contents of your carton for possible shipping
or handling damage and report any such damage directly
to your authorized Casablanca dealer.
• It is always a good idea to have an assistant to help with
the installation.
Fuse Box
(Remove fuse for the
circuit you will be
working on)
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
• The blades in each pack are matched for equal weight
to assure smooth fan operation. If more than one fan is
being installed, be careful not to mix blades from different
cartons.
•Never install a fan over a pool or spa.
• For safety reasons, the fan blades must be a minimum of
7 feet above the floor.
• In any installation, the tips of the blades must be at least 18
inches from the wall in order to provide sufficient clearance
for the blades.
18" ↑
•Never insert anything into the path of the fan blades while
the fan is in operation.
• When cleaning, painting, or working near your fan, be
very careful of the fan and blades. Always turn the power
OFF to the ceiling fan before servicing it, working on it,
or replacing lightbulbs.
•Never operate a fan that has been damaged in any way.
For assistance in obtaining service, call Casablanca Fan
Company toll-free at 1-888-335-5247, or contact your
local Casablanca Authorized Dealer.
2
84" ↑
Trident™
MOUNTING RECOMMENDATIONS
General Guidelines
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
support
brace
Ceiling fans have practical uses in almost every room in your home. We suggest
you follow these mounting recommendations as you decide where to install
your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7' above the floor.
standard
mounting
style
• Do not locate the fan in a doorway or above a swinging door.
• In bedrooms, fans work best when mounted above the foot of the bed.
ceiling outlet
box
• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan
blades.
• Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy the finish and
warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms, two fans may
be needed.
Sloped Ceiling Installations
Suggested Extension Pole Lengths
Ceiling Height
8' 0"
8' 6"
9' 0"
9' 6"
10' 0"
11' 0"
12' 0"
13' 0"
14' 0"
Pole Length
Extension
Pole
standard
standard
6"
12"
12"
18"
24"
36"
48"
Maximum
Hang-Tru®
angle 32º
Blades must be a
minimum of 7 feet
above the floor
7' minimum
When to Use Extension Poles
For best performance and appearance, an extension pole
should be used with your Casablanca fan when installing
on high (cathedral) ceilings or sloped ceilings. Casablanca
offers standard poles in increments of 6 inches up to 5 feet.
Custom poles are available in lengths up to 9 feet 9 inches.
See your Authorized Casablanca Dealer for details.
Note: The fan may wobble or vibrate if pole length is
not long enough and inside blade is too close to downslope
or side wall. Extending pole length will usually solve
problem.
Calculation of 32 Degrees
Use the tear-off Ceiling Angle Template card inserted in
this manual. It provides you with a simple “go” or “no-go”
for installing your fan on a sloped ceiling.
EXAMPLE 1
EXAMPLE 2
EXAMPLE 3
This slope is less than 32º.
It is OK to install your fan.
This slope is 32º. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your fan.
This slope is more than 32º. Your fan will not
hang straight down, an adaptor is necessary.
Contact your local Authorized Casablanca
Dealer in regards to purchasing a “Sloped
Ceiling Adaptor.”
3
Fan Installation
Getting Started
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.
warning!
To reduce the risk of fire, electrical shock, or
personal injury, mount to outlet box marked
“Acceptable Fan Support of 22.7 kg (50 lbs.) or
less” using the mounting hardware provided with
the outlet box.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either the circuit
breaker or fuse box), lower the old fixture and disconnect
the wiring. Check the ceiling fixture outlet box to be sure
it is marked “Approved for Ceiling Fan Mounting.” If it is
not, a new box must be installed.
Note: The weight of this fan is 19 pounds.
Crossbar Mounting Bracket Installation
Ceiling Hardware (not to scale)
Crossbar Mounting Bracket
Pack A:
Lag Screw and Washer (1)
1" x 8-32 Roundhead Screws and Washers (2)
Note: After removing the old fixture, check the outlet box
to insure that it is supported by a joist or beam across its
upper surface. If not, a 2 x4 stud must be installed.
Step 1a. Remove the knockout plug in the center of the
outlet box or drill a 1/2-inch hole for the lag screw to pass
through. Then drill a 1/4-inch guide hole into the joist or
beam to a depth of 3 inches.
Step 1b. Route the outlet box wires through the center
hole of the crossbar mounting bracket as shown. Attach
the crossbar mounting bracket to the outlet box with the
screws provided in Pack A, making sure the outlet box
wires are not pinched by the washer.
Joist
Ceiling-Fan-Approved Wiring
Box
Crossbar Mounting
Bracket
Green Ground Wire
CAUTION:
To reduce the risk of personal injury, use only the
mounting hardware provided with the approved
outlet box to install the crossbar mounting
bracket.
warning!
Support directly to building structure only.
4
Wire Nuts (4)
1" x 8-32
Roundhead Screw
Ceiling Wiring
Ridge side down
Washer
Trident™
Lag Screw Installation
NOTE: This step is required only under two conditions:
If the fan weighs 35lbs. or more (which does not pertain
to this fan) or if the existing ceiling fixture outlet box
needs to be modified for a ceiling fan application (for
example, if the house is not new construction and you are
replacing an existing light fixture). We recommend that
the ceiling box be of sufficient capacity to support the
weight of the fan and light fixture under any conditions. If
in doubt whether you need to install the lag screw, consult
a qualified electrician.
Step 2 (optional). With the large washer attached, pass
the lag screw through the center hole of the crossbar
mounting bracket and screw into the guide hole. Tighten
until outlet box is mounted firmly to the beam. This box
must be secured to the ceiling firmly.
Large Washer
Lag Screw
Canopy Installation
Canopy Hardware (not to scale)
Canopy Hatch
Canopy Screws and
Washers (5)
Canopy
Step 3. Attach the canopy to the crossbar mounting bracket
with three of the 8-32 x 21/2" long canopy screws and lock
washers provided with your Casablanca fan. Tighten using
the provided screwdriver until snug against the ceiling.
NOTE: On sloped ceilings, align the canopy opening with
the top or peak of the room.
Feed outlet box
wires through
canopy opening
Canopy
Lock Washer
Canopy Screw
5
Fan Preparation
Perma•Lock™ Hardware (not to scale)
Allen Wrench
3" Perma•Lock™ Downrod
and Ball Assembly
IMPORTANT SAFETY INFORMATION:
Before starting the installation of your ceiling
fan, install the threaded downrod into the motor
coupling and lock the assembly.
Motor Wires
(leave at least 6" long)
Prepare for fan installation as follows:
Step 4a. Remove the paper shield from the motor.
Step 4b. Using the provided allen wrench (attached to the
paper motor warning shield), loosen the allen set screw
attached to the motor coupling.
Step 4c. Route the wires through the Perma•Lock ™
downrod and ball assembly. Insert the downrod into the
motor coupling and turn it clockwise until it stops turning,
ensuring that the pole has bottomed out.
Allen Wrench
Allen
Set Screw
Ground Wire
(green)
Perma•Lock™ Downrod
and Ball Assembly
Tapered thread
Motor
Coupling
Caution Shield
Motor Housing
Assembly
Tip: The downrod has a tapered thread that is designed
to lock completely when installed correctly.
Step 4d. Tighten the set screw with the allen wrench to
ensure safe operation of your fan. If it is tight enough, you
should not be able to turn the downrod counterclockwise
with your hands. If in doubt, tighten the set screw with the
allen wrench until you cannot turn it any further.
Caution Shield
CAUTION: Failure to fully lock in the downrod
before securely tightening the allen set screw may
cause the fan to separate from the downrod and fall
during normal operation.
6
Trident™
Blade Installation
Blade Hardware (not to scale)
Pack C:
Metal Washer (9)
Pack C:
Blade Screws (9)
Blades (3)
Blade Assembly
Step 5. Attach a blade to the motor as shown using the 3
blade scres and 3 metal washers. Repeat for each blade.
NOTE: Be sure that the blade badge is facing
downward.
TIP: For balancing purposes, loosely install all three blades
to the motor before tightening the blade screws securely.
Caution:
Blade screws must be tightened securely before
operating the fan.
7
Hanging the Fan
Step 6a. To hang the fan body in the canopy, hold the fan
body firmly and insert the ball into the canopy opening.
Check that no wires are pinched. Rotate the fan body until
the slot in the ball fits into the pin opposite the canopy
opening.
Step 6b. Trim excess motor wires, leaving at least 6 inches
above the downrod. Strip 1/2-inch insulation from the end
of each wire using a wire stripper (available at your local
hardware store). The splices after being made should be
turned upward and pushed carefully into the outlet box.
Ball
Slot
Canopy Electrical Connections
Step 7. Attach the fan wires to the ceiling fixture outlet box
wiring by placing the bare ends of the wires side by side and
then securing with a wire nut. Test that the connection is
secure by pulling on the wire nut. Connect in this order:
• GREEN leads from mounting plate and downrod
assembly of fan to GROUND conductor of power
source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in
ceiling fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to BLACK power wire in
ceiling outlet box. Secure with wire nut.
After making the wire connections, the wires should
be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet
box and the ungrounded conductor on the other side of
the outlet box.
Wire Nut
2 Black Wires
2 White Wires
3 Green Wires
NOTE: If the color of your ceiling wires differs from that
described, consult an electrician.
Canopy Hatch Installation
Step 8a. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are
on opposite sides of the canopy and all
wires are clear of the canopy opening.
Step 8b. Install the canopy hatch with the
last canopy screw and lock washer using
the provided screwdriver. To do this, tilt
the fan body away from the hatch opening.
Tighten the screws firmly.
Canopy Hatch
Canopy Washer
Canopy Screw
Tilt the fan to install last
canopy screw
8
Pin
Trident™
Install LIGHT BULB AND GLASS
Step 9a. Remove the socket plug from the light bulb socket
and put aside for safe keeping. If you ever decide to install the
no light cap option you will need the plug. Screw the 100 Watt
Halogen bulb into the socket. Do not touch the glass bulb with
your fingers-it is extremely important that the glass be clean. If
it is touched, or dirty, clean carefully with a tissue. A dirty glass
bulb will cause the bulb to fail almost immediately.
IMPORTANT! When installing the halogen bulb,
carefully cut off the end of the plastic sleeve the bulb
comes in and hold the bulb by the plastic sleeve to
screw it into the socket.
Socket Plug
Tabs
Halogen Bulb
Halogen Bulb
100 Watt
Step 10a. Position the indentations in the outer rim of the glass
shade so that they line up with the tabs on the inside surface of
the fan light fixture rim.
Step 10b. Carefully lift the glass shade up inside the light fixture
as far as it will go.
Step 10c. Rotate the shade in a clockwise direction until it is
held tightly in place by the three tabs.
Glass Shade
Glass Shade
Indentation
Note: In compliance with US Federal Energy Regulations, this ceiling fan contains a device that resctricts
the light kit to a maximum of 190 watts. Exceeding
that limit or the marked limit on this product may
result in fire hazard or improper operations.
MOUNTING THE NO Light CAP
Step 11a. Remove existing glass by gently pushing up on the
glass and rotate glass counter-clockwise until the glass tabs from
the fixture align with the indentations on the glass.
Step 11b. Remove halogen light bulb from socket.
Step 11c. Package up glass and bulb for safe keeping if you ever
decide to re-install.
Step 12a. Install socket plug into the socket.
Step 12b. Take the No Light Cap and position the indentations
in the outer rim of the cap so that they line up with the tabs on
the inside surface of the fixture rim.
Socket Plug
Step 12c. Carefully push the cap up inside the light fixture as
far as it will go and rotate in a clockwise direction until it falls
into the notch for each tab.
Step 12d . Turn power back on at the circuit breaker or fusebox.
This completes the installation of the No Light Cap.
No Light
Cap
9
Prime •TOUCH® Control INSTALLATION
PRIME•Touch2™ Hardware (not to scale)
12v Battery
W-505
Control
Drywall Anchor
6-32 (2)
Wood
Screw
1" (2)
Screw
6-32 X 3/8"
(2)
W-505
Control Bracket
Control Bracket Installation
SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with
an isolating wall control/switch. CAUTION! Do not use with wall dimmer.
Step 10. Follow instructions below for the type of
transmitter control you will be installing.
Standard Toggle Light Switch
a. Remove the two screws holding the switch cover plate.
Do not remove the cover plate.
b. Orient the control bracket as shown and line up the two
inner mounting holes with those on the switch.
c. Install and tighten screws using the provided
screwdriver.
CAUTION! Do not use with wall dimmer.
warning! To reduce the risk of fire or electric
shock, do not use this fan with any solid state speed
control device. Use only the control provided with
this fan.
Wall Installation
a. Locate a 2 x 4 wall stud in a convenient -location.
b. Orient the control bracket as shown over the 2x4 stud.
c. Use the 1-inch wood screws in the inner mounting
holes. Insert and tighten the screws using the provided
screwdriver.
Note: The wall anchors and 6-32 x 1” screws may be
used in situations where mounting to a stud is not possible.
Use the inner mounting holes. After securing the anchor,
discard the anchor’s pointed screws and use the supplied
6-32 decor ovalhead screws.
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions: (1) This device may not cause
interference, and (2) This device must accept any
interference, including interference that may
cause undesired operation of the device.
10
NOTICE: Changes or modifications not expressly
approved in writing by Casablanca Fan Company
may void the user’s authority to operate this
equipment.
Remote Operation
Fan Control
Trident™
To start the fan, press the appropriate speed button to run the fan at the desired
speed.
• = Low speed
•• = Medium speed
••• = High speed
Reverse
Send Signal
LED
High
Med
To turn off the fan, press the FAN OFF button.
Low
Airflow Direction
To reverse the airflow, press the REVERSE button. Reverse operates at any speed,
whether the fan is on or off. The fan returns to its set speed after reversing.
Fan
Off
Light
Light Control
Turn the light on or off independently from the fan by pressing the LIGHT button. If
you press the button for more than 0.7 seconds, it becomes a dimmer. The light varies
from “bright” to “dim” over approximately 8 seconds. If you continue to hold the LIGHT
button, this sequence will reverse when the light reaches the brightest or dimmest level.
Release the button when the desired level is reached.
Changing Transmitter Frequency Setting
Note: All fans leave the factory set to “0000.”
You will only have to change the dip switch settings in the remote
if you are using more than one fan in the same area and want to
control them separately.
Step 1. At the circuit breaker or fuse box, turn the power off for
the fan you want to change.
Dip Switch
Set to “1000”
Dip Switch
Set to “0101”
Step 2. Open the battery door of the Prime•Touch control and
remove the batteries.
Step 3. Change the dip switch settings, assuring that they are
different from the previously installed Prime•Touch fan.
Step 4. Re-install the batteries and the battery door on the control.
Step 5. At the circuit breaker or fuse box, turn the power back
on for the fan whose frequency you are changing.
Step 6. Within 20 seconds of restoring power, push the High,
Med, and Low buttons (in that order).
warning!
Do not turn the power off at the circuit breaker, then
back on, for the previously installed Prime•Touch
fan(s), as you may inadvertently change the frequency
settings for it as well.
Note: You may want to label your controls to assure you
do not mix them up.
High 3
med 2
low 1
If the fan is not functioning after installation:
Step 1. Check to make sure that batteries are installed correctly
in the control.
Step 2. Turn the power off to the fan (from the circuit breaker)
for at least 5 seconds.
Step 3. Turn the power back on (at the circuit breaker) and push
the High, Med, and Low buttons–in that order–within 20
seconds.
Circuit Breaker
or Fuse Box
Press in this order to set new
frequency:
1. High
2. Med
3. Low
Step 4. The fan should now function properly.
11
Troubleshooting tips
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
PROBLEMPOSSIBLE REMEDIES
Fan will not start
• Check the main circuit fuses, circuit breakers, and wall switch position. Check
all wire connections. Make sure the power is turned off during this inspection.
• The battery is weak. Install a fresh battery.
• The fan receiver is defective. Replace the fan receiver.
Fan wobbles or shakes excessively
• Check the frequency setting: Turn the power off at the circuit breaker for the
fan that is not functioning only. Check that the jumper switches match in both
the receiver and the transmitter.
• Be sure the canopy pin is set properly into the slot on the ball.
• Check that the bladeholders have not been bent during installation and the blades
are balanced.
• The hanger bracket and/or the ceiling outlet are attached too loosely. Make sure
the hanger bracket is attached tightly to the ceiling outlet box and the downrod
assembly is secured firmly.
Fan is noisy during operation
• The downrod is attached to the downrod base too loosely. Make sure all the
screws are securely tightened.
• Check and tighten the light fixture retaining screws, glass shade screws, and/or
lightbulb(s).
• Tighten the canopy screws and mounting plate assembly. Make sure the wire
nuts inside the canopy and switch housing are not touching the metal parts and
that they have not fallen off the wire splices. Tighten as necessary.
• Tighten the blade holders to the flywheel (or direct drive motor) and the blades
to the bladeholder screws.
Fan does not run on low speed
Battery life is short
Light works, but fan does not work
Fan and light run only on full speed Fan is missing one speed
• Make sure all the screws in the motor housing are snug but not overly tight.
• If fan is new, it may need to be “broken in.” Run at high speed for several days.
• Replace with alkaline batteries.
• The fan wires are not connected properly. Follow the instructions in Step 8.
• The fan receiver is defective. Replace the fan receiver.
• The fan receiver is defective. Replace the fan receiver.
Fan does not change speed, but light works • The fan receiver is defective. Replace the fan receiver.
Reverse does not work
Fan starts working by itself • The fan receiver is defective. Replace the fan receiver.
• There is frequency interference. Change frequency as described on Page 11.
Fan operates only when transmitter is close • Check that antenna wire is not touching the metal plate.
Fan works, but light does not dim
• The fan receiver is defective. Replace the fan receiver.
• The light socket is broken. Replace the socket.
Fan works, but light does not work
• The fan receiver is defective. Replace the fan receiver.
• A lightbulb is defective. Replace the lightbulb.
12
Trident™
Care Recommendations
Fan Finishes
• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened
soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish.
Blades
• Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
• For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily using a mild
detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these
will damage the finish.
No Need for Lubrication
• Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated
for life.
• Do not attempt to oil the motor.
Changing Lightbulbs
• Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
• Replace bulbs with the same type as you removed from the light fixture.
• The maximum wattage rating for this fan’s light kit is 120 watts for the light.
• In compliance with US Federal Energy Regulations, this ceiling fan contains a device that restricts the light kit to a maximum
of 190 watts. Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation.
For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178
or visit us on the web at: www.casablancafanco.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communication. However, there is no guarantee that the interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company
may void one's authority to operate this remote control.
13
Product Specifications
Model Name:TridentTM
Model Number:TRIH-XX
Dimensions:
Dimension B
NOTE:
includes light fixture
and glass.
Weight:
A =12"
B = 15"
C =3.25"
D =11.4"
E =5.6"
19 lbs.
Motor:
Blade Span:
Blade Iron Pitch:
No. of Blades:
Technology:
Lightbulbs:
188 x 20mm Direct DriveTM
54"
14°
3
Prime•Touch® W-505
(1) 100-watt Halogen bulb
Airflow:
Electricity Use*:
Airflow Efficiency*:
6,694 cfm
86 watts
92.7 cfm/watt
* Performance data is for fan only. No lighting wattage is included.
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising