Blackhawk USB560 m JTAG Emulator Quick Start Guide

Below you will find brief information for JTAG Emulator USB560 USB560m. This device is a JTAG emulator that allows you to debug and program Texas Instruments DSPs. It is compatible with Code Composer Studio, a software development environment for TI DSPs. The JTAG emulator uses USB2.0 for communication and is compatible with a number of popular DSP targets, including TMS320C55x, TMS320C64x, and TMS320C66x.

PDF Download

Document

4 CCStudio Setup
A.) Importing a Pre-defined Import or Factory Board
These instructions apply to CCStudio v2.2 - v3.3, but the import dialog varies slightly between versions. Refer to the USB560m Installation Guide if more information is needed.
1.
2.
3.
Run CCStudio Setup. And for CCStudio v3.0 and earlier, start the “Import a
Configuration” dialog.
Find and select “bh-usb560(m)emulator” from the “Platform” pull down menu
located at the top of the middle CCSetup window or in the center of the import
dialog box (this will list the USB560m imports).
You can narrow down the import options further by using the “Family” pull down
(i.e. select “C55xx“ to list all TMS320C55x device imports).
4.
When you find your target, or an import close to it, highlight the entry and choose
the option to “add it to your system”.
5.
If this import setup does not completely match your target, you can edit the properties manually (i.e. to add or change a GEL file).
QUICK
START
GUIDE
Blackhawk™
USB560
JTAG
Emulator (USB560m )
Installation Requirements
•
PC or Notebook computer with at least one free USB v1.1 or v2.0 port.
•
Windows&reg; 2000/XP/Vista Operating Systems (32 or 64-bit versions).
•
Texas Instruments Code Composer Studio version 2.2 or later.
•
CD ROM Drive.
†
Inventory of Items Included
6. When finished, save the setup and start CCStudio.
B.) Using Create Board for CCStudio v3.1 and later
1.
2.
Run CCStudio Setup.
Select the “Create Board” tab and drag the “BH USB560-M Connection” to
My System on the left. This will prompt you for a connection name. You can
enter any string you want, but at a minimum, it typically includes the emulator
name and target DSP or board name (i.e. “Blackhawk USB560m—C5509”).
3. Now, highlight the new connection name you added under My System and add
the available processor(s) from the middle window to match your hardware.
4. Save your setup and start CCS.
C.) Changing an XDS560 PCI import for CCStudio v2.2-v3.0
1.
2.
3.
4.
Run CCStudio Setup and import a setup for the TI XDS560 PCI card that
matches your target (refer to section (A.) above for importing).
Highlight the board you added under My System, right click with the mouse and
choose properties.
Locate the Emulator Name field under board properties tab and change the
name from “XDS560 0” to “BH560USBM 0”. If you need to change other properties (GEL, DSP, etc.) , you can do that too.
Save CCSetup and start CCS.
1. Blackhawk USB560 JTAG Emulator
POD (USB560m).
2. USB 2.0 Compliant Cable.
3. 5 Volt DC power supply.
4. AC power cord.
5. 20-pin cTI JTAG cable.
6. 20e_cTI-14t_TI Pin Converter.
7. 20e_cTI-20t_ARM Pin Converter.
8. 20e_cTI-60t_TI Pin Converter.
9. Installation CD ROM.
10. Warranty and Product Registration
Cards.
11. Quick Start Guide.
Other Items Required
1. Target Board System—a selfpowered board with a TI DSP and
compatible JTAG header connection conforming to IEEE 1149.1
Standard.
2. Copy of Code Composer
†
Studio Version 2.2 or later.
IMPORTANT
ENVIRONMENTAL
CONSIDERATIONS
This equipment is designed to
be operated under the following environmental conditions:
Temperature between 0&deg;C –
55&deg;C. Relative Humidity of
20% - 70% non-condensing.
Operation of the unit outside of
the above range may affect
structual and mechanical
integrity and cause permanent
damage.
Caution is necessasry to
minimize ESD (Electro-stactic
Discharge) which can damage
electronic components. Use in
a controlled environment
where ESD materials and
practices are employed is
highly recommended.
†
4
Blackhawk
123 Gaither Drive, Mt. Laurel, NJ 08054-1701
www.blackhawk-dsp.com
Blackhawk is a registered trademark of EWA Technologies, Inc.
USB560m-QS-06
For CCStudio v2.0 and v2.1 (only), download the XDS560 emulation driver subsystem from the TI web site:
https://www-a.ti.com/downloads/sds_support/XDS560Update.html. These files are included with CCS v2.2 and later.
A TI USCIF Update (v35.23.10.0) is necessary for CCStudio v3.2 or earlier, which is included with our
driver installations on CD ROM and Web Site.
1
USB PnP Installation 3
1 Emulation Driver Installation
The USB560m JTAG Emulator shipped with its emulation drivers on CD ROM
media that are needed by Windows and CCStudio for operation.
Windows 2000/XP/Vista
1. Make sure the USB560m Emulator is powered.
1. Insert the Emulation Driver CDROM into your PC’s CDROM drive.
2. Follow the installation wizard, and when done, you are ready to install
the emulator hardware.
If the installation executable fails to start automatically, run X:\Setup\Setup.exe,
where [X] is the drive letter for your CD ROM drive.
2 Hardware Installation
WARNING
Be careful to connect interface cables with the correct orientation. Pin 1 on
the interface cable should match Pin 1 on the DSP system connector. The
JTAG cable assembly features a &quot;keyed&quot; connector to minimize the chance
of error.
Do not force cables into position. Forcing them may damage the cables or
the interconnected boards and systems.
2. If not already connected, connect the USB cable to the USB560m and to
the computer.
3. Follow the Windows “Found New Hardware” wizard prompts.
4. You can select the “automatic” option for locating drivers.
5. If the automatic option did not locate them, you can manually specify the
location. These files were installed to your system during the Emulation
Driver Installation - section 1. The typical location for these files is
folder: C:\CCStudio_v3.3\blackhawk\drivers.1 , where
&lt;C:\CCStudio_v3.3&gt; is the location selected in section 1.
6. When completed, the Blackhawk Control Panel and Windows Device
Manager will show the device. The Blackhawk Control Panel can be activated from its icon, located in the Windows Control Panel Dialog Box.
7. Now follow the Code Composer Studio Setup in section 4.
1. Place the USB560m module in desired location.
2. Connect the 5v DC power plug of the power supply to the 5-volt DC
input on the USB560m (see figure 1).
High Speed USB
Cable Connection
5 Volt DC Power
Supply Connection
3. Attach the USB cable to an available USB port on the PC and to the
USB connector on the USB560m (see figure 1).
Use of a USB hub for isolation between the PC and the
emulator is STRONGLY recommended.
4. Once the emulator is powered and attached to the PC, the Windows
Found New Hardware Wizard will start.
FIGURE 1—USB &amp; Power End Panel
5. Follow the Windows Plug and Play Found New Hardware Wizard installation for the Windows device driver (refer to section 3 on USB PnP
Installation).
JTAG Cable
Connection
Emulator ships with JTAG
cable already attached.
6. After enumeration, attach the JTAG cable assembly to the target
board. Make sure the target is not powered when connecting!
7. Setup and start CCStudio as described in section 4, CCStudio Setup.
2
FIGURE 2—JTAG End Panel
3
">

Hello! I am an AI chatbot specifically trained to assist you with the Blackhawk USB560 m JTAG Emulator Quick Start Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Hide related prompts

Assistant typing

Assistant terminated