MerCruiser MEFI 3 Engine User manual

Table of Contents
Page
Speed / Density Theory and Operation . . . . .
1-1
Speed/Density Theory . . . . . . . . . . . . . . .
1-1
Mass Air Flow Systems . . . . . . . . . . . . . .
1-1
Speed/Density Operation . . . . . . . . . . . . .
1-2
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3
MEFI 3 ECM Input and Sensor Descriptions .
1-4
PCM 555/03 Input and Sensor Description. . .
1-5
Two-Wire and Three-Wire Sensors . . . . . . . . .
1-6
MEFI ECM Identification
....
1-7
ECM555 and PCM555/03 Identification
..............
1-8
Factors Determining Fuel Injector Pulse Width . 1-9
MEFI ECM Comparison
. . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
MEFI-3 and Audio Warning . . . . . . . . . . . . . . . 1-12
Additional MEFI-3 ECM Features . . . . . . . . . 1-13
Moving Desired RPM Mode (ECM’s with
Delphi #1623999) . . . . . . . . . . . . . . . . . 1-13
Load Anticipation Mode . . . . . . . . . . . . . . 1-13
Shift Switch Operation . . . . . . . . . . . . . . . 1-13
ECM/PCM 555 Engine Guardian Strategy &
Additional Guardian Sensors . . . . . . . . . . . 1-14
ECM 555 Warning System Operation . . . . . . 1-15
Manifold Vacuum / Pressure Reference Chart . 1-18
Vacuum Gauge vs Map Sensor . . . . . . . . . . . . 1-19
Fuel Systems Diagrams . . . . . . . . . . . . . . . . . . . 1-20
Multi-Port Injection with Vapor Separator
Tank (VST) . . . . . . . . . . . . . . . . . . . . . . 1-20
350 Magnum Multi-Port Injection with
MEFI 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
Throttle Body Injection with
Vapor Separator Tank (VST) . . . . . . . . 1-22
Throttle Body Injection With
Cool Fuel System . . . . . . . . . . . . . . . . . 1-23
1-i - EFI SYSTEM COMPONENTS/OPERATION
Page
Fuel Pressure Regulator Assembly . . . . . . . . 1-24
“Cool Fuel” System Fuel Pressure
Regulators . . . . . . . . . . . . . . . . . . . . . . . 1-25
Fuel Pressure Regulator Identification
(Revised Aug. 6, 2004) . . . . . . . . . . . . . . . . 1-26
Fuel Injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28
Throttle Body Injection (TBI)
Fuel Injector . . . . . . . . . . . . . . . . . . . . . . 1-28
Multi-Port Injection (MPI) Fuel Injector . 1-28
Fuel Injector Identification
(Revised (Aug. 6, 2004) . . . . . . . . . . . . . . . . 1-30
Engine Wiring Diagrams . . . . . . . . . . . . . . . . . 1-32
MEFI 3 MCM 5.0L EFI, 5.7L EFI and
350 Mag MPI Engines . . . . . . . . . . . . . 1-32
MEFI 3 350 Magnum MPI and
All Black Scorpion Engines . . . . . . . . . 1-33
ECM Wiring Diagram – MEFI 3
(V6 and Small Block V8) (1 of 4) . . . . . . . . 1-34
ECM Wiring Diagram – MEFI 3 (V6 and
Small Block V8) (2 of 4) . . . . . . . . . . . . . . . . 1-35
ECM Wiring Diagram – MEFI 3 with Mercury
Distributor (V6 and Small Block V8) (3 of 4) . 1-36
ECM Wiring Diagram – MEFI 3 with
GM EST Distributor
(V6 and Small Block V8) (4 of 4) . . . . . . . . 1-37
PCM 555 – Charging Harness . . . . . . . . . . . . 1-38
PCM 555 – 10 Pin Harness Circuit . . . . . . . . 1-39
PCM 555 – Crank Position and
Camshaft Position Circuits . . . . . . . . . . . . . 1-40
PCM 555 – Fuel Injector Harness . . . . . . . . . 1-41
PCM 555 – Ignition Circuit . . . . . . . . . . . . . . . . 1-42
PCM 555 – Coil Harness Circuit . . . . . . . . . . . 1-43
MEFI III to IV ECM Conversion Kits . . . . . . . 1-44
Gen III Cool Fuel System . . . . . . . . . . . . . . .
1-55
Gen III Cool Fuel Module Diagnostics . . . . .
1-63
MerCruiser EFI III (1004)
1
Speed / Density Theory and Operation
Speed/Density Theory
All MerCruiser EFI engines operate on the fuel injection strategy called “Speed/Density”. This
means that the ECM primarily looks at the engine’s speed and the intake manifold’s air density in order to calculate the correct amount of fuel to inject.
The engine requires an air/fuel mixture of approximately 14:7 to 1 in the combustion chambers. Since the EFI system doesn’t control air flow, it must determine how much air is flowing
through the engine in order to calculate the correct amount of time to fire the fuel injectors.
The net result is that there must be 1 part of fuel for every 14.7 parts of air going through the
engine.
Since the engine is basically an air pump, we know that an engine is capable of pumping a
certain (maximum) amount of air at any specific rpm. The actual amount of air it pumps (at
a specific rpm) depends on the density of the air in the intake manifold. The air density (in the
intake manifold) will vary depending on rpm, throttle plate position and barometric pressure.
If the air density in the intake manifold is known, the actual amount of air flowing through the
engine (the “Air Mass” or “Mass Air Flow”) could be calculated. This calculated (and the actual) air flow is a repeatable function, meaning that at a specific rpm and a specific manifold
absolute pressure reading, the air flow through the engine will always be the same.
However, in the speed/density system we do not actually calculate the actual air flow. Instead,
the ECM measures the rpm and the air density, then refers to a programmed “lookup table”
in the ECM’s EEPROM. This lookup table will be programmed with the correct fuel injector
information for every rpm and density reading. The programming engineer has to come up
with these figures, because the ECM is not actually calculating the Mass Air Flow.
The speed-density system depends on the engine being unmodified (from its original production state). If we change the volumetric efficiency of the engine in any manner, the amount
of air flow for a given rpm and air density will change, causing the ECM to deliver the incorrect
amount of fuel. Any modification to the following components will influence the air flow
through the engine, throwing the speed-density system out of calibration.
1. Pistons and combustion chambers (anything that changes the compression ratio).
2. Camshaft changes (effecting the valve timing, lift and duration).
3. Changes to intake and exhaust valve size, as well as “porting and polishing”
4. Installing different intake and/or exhaust manifolds.
5. Installing a different size throttle body and/or flame arrestor.
Mass Air Flow Systems
Mass Air Flow systems actually measure the amount of air (or “Air Mass”) entering the engine,
so they generally can compensate for modifications or changes to the air flow through the
engine. While these systems are generally considered more accurate, they are generally not
as robust (and cost effective) as the speed-density system. Mass Air Flow systems are typically used in automotive applications to meet stringent emissions and fuel economy requirements.
One method of measuring the mass of the air flow into the engine is the “Hot Wire” system.
A small wire is stretched across the air intake. An electrical charge is run through the wire
(causing it to heat up). As air flows over the wire, it changes the temperature of the wire, which
changes its resistance (and the resulting current flow). The ECM can pick up this change in
current flow and calculate the amount of air entering the system.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-12
Another method of measuring the mass of the air flow into the engine is the “vane-type” Mass
Air Flow sensor. A movable vane is mounted in (protrudes into) the air intake system. The rush
of intake air through the sensor causes the vane to be deflected. The deflection is measured
and a signal sent to the ECM.
NOTE: The speed-density system is more than accurate enough for our marine applications.
The additional reduction in emissions and the resulting increase in fuel economy (with the
Mass Air Flow system) are negligible. But when automotive manufacturers must meet emissions standards, they often have to take small improvements where they can find them.
Speed/Density Operation
The engine’s RPM is easily determined from the REF HIGH signal on systems with EST ignition, or the timing signal from the Thunderbolt Distributor’s hall-effect sensor on small-block
MEFI 3 models.
To determine the density of the air in the intake manifold, we need to know the intake manifold
vacuum, which we measure with the MAP (Manifold Absolute Pressure) sensor. It is important
to remember that a MAP sensor measures the manifold pressure above absolute zero (like
a barometer), while a conventional vacuum gauge measures the manifold pressure below
the current atmospheric pressure. The use of the Manifold Absolute Pressure Sensor allows
us to compensate for variations in atmospheric pressure due to weather and altitude changes. A conventional vacuum gauge would not provide us with this needed information.
NOTE: While the temperature of the air does affect its density, not all engines use an IAT (intake air temperature) sensor. If no IAT is present, then the ECM assumes 75 degree Fahrenheit for all density calculations. If an IAT is present, then the ECM can more accurately determine the air’s density. However, the amount of correction the IAT adds is a relatively small
amount (approximately 10% maximum change in fuel flow).
In review, our standard, unmodified production engines flow a repeatable (and therefore
“known”) amount of air at any specific engine rpm and manifold pressure. With this knowledge, the ECM can be programmed to deliver the correct amount of fuel from the combination
of the speed sensor (distributor signal) and density information (from the MAP sensor).
It is often said that the speed-density system runs “in theory alone”, since the ECM doesn’t
really know how much air is flowing through the engine, it is just assuming it knows how much
(based on the repeatability of airflow theory). In reality, the system is simple, rugged and
works extremely well. But, the ECM cannot compensate for changes in volumetric efficiency
of the engine.
1-2 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
3
Abbreviations
Amp
Amperes
IAC
Idle Air Control
Barometric Pressure
IAT
Intake Air Temperature
Bat
Battery Positive Terminal,
Battery or System Voltage
IC
Ignition Control
B+
Battery Positive
Bps
Beeps
CAM
Camshaft
INJ
Injection
cond
Condition
kPa
Kilopascal
cont
Continuous
KS
Knock Sensor System
Crank
Crankshaft
kV
Kilovolts
CAN
Control Area Network
mA
Milliamperes
CKT
Circuit
MPR
Main Power Relay
CMP
Camshaft Position Sensor
MAP
Manifold Absolute Pressure
Conn
Connector
MAT
Manifold Air Temperature
CPS
Crankshaft Position Sensor
MIL
Malfunction Indicator Lamp
BARO
Cyl
Cylinder
IGN
In. hg.
mohms
Inches of Mercury
Milliohms
DDT
Digital Diagnostic Tester
Deg
Degrees
N/C
Normally Closed
Diag
Diagnostic
N/O
Normally Open
DIS
Distributorless Ignition System
PCM
Propulsion Control Module
Dist
Distributor
DLC
Data Link Connector
DTC
Diagnostic Trouble Code
REF HI
Reference High
Digital Volt Ohm Meter
REF LO
Reference Low
DVOM
mSec
Ignition
PROM
RAM
Millisecond
Programmable Read Only Memory
Random Access Memory
DMM
Digital Multimeter
ROM
Read Only Memory
DMT
Digital Multimeter & Tachometer
SLV
Slave
ECM
Engine Control Module
SW
Switch
ECT
Engine Coolant Temperature
TACH
Tachometer
Electronically Erasable Programmable
Read Only Memory
Term
Terminal
Electronic Fuel Injection
TPS
Throttle Position Sensor
EEPROM
EFI
EMCT
Exhaust Manifold Coolant Temperature
V
EMI
Electromagnetic Interference
Vac
ERC
Electronic Remote Control
WOT
ESC
Electronic Shift Control
ETC
Electronic Throttle Control
GND
Ground
HEI
High Energy Ignition
HVS
High Voltage Switch
MerCruiser EFI III (1004)
Volts
Vacuum
Wide Open Throttle
EFI SYSTEM COMPONENTS/OPERATION - 1-34
MEFI 3 ECM Input and Sensor Descriptions
d
c
KNOCK
SENSOR 2
(7.4L)
DISCRETE SWITCHES
(AUDIO WARNING)
e
KNOCK
SENSOR 1
b
a
SYSTEM
RELAY
f
DIST. FOR
REF RPM
h
j
LOAD
SW
FP
g
TP
k
i
MAP
IAT
ECT
INPUTS l
ECM m
OUTPUTS n
o
q
FUEL
PUMP
RELAY
IGNITION
CONTROL
r
p
- System Relay
- Dist. For Ref. RPM
- Discrete Switches (Audio Warning)
- Knock Sensor 2 (7.4L)
- Knock Sensor 1
- TP
- MAP
- Load Sw.
- ECT
- FP
- IAT
1 - 4 - EFI SYSTEM COMPONENTS/OPERATION
FUEL
INJECTORS
IAC
MOTOR
V-REFERENCE
(5-V OUTPUT
TO SENSORS)
FUEL
PUMP
a
b
c
d
e
f
g
h
i
j
k
t
s
u
AUDIO
WARNING
BUZZER
v
SERIAL
DATA (DLC)
l - Inputs
m- ECM
n - Outputs
o - Fuel Pump Relay
p - Fuel Pump
q - Ignition Control
r - V-Reference (5-V Output to Sensors)
s - IAC Motor
t - Fuel Injectors
u - Audio Warning Horn (Buzzer)
v - Serial Data (DLC)
MerCruiser EFI III (1004)5
PCM 555/03 Input and Sensor Descriptions
The following lists the sensors, switches, and other inputs used by the PCM 555 to control
its various systems. Although we will not cover them all in great detail, there will be a brief
description of each.
ff
c
b
a
ee
d
g
j
e
h
k
f
i
l
m
gg
dd
o
n
PCM
jj
hh
q
p
r
ii
cc
aa
bb
z
v
w
t
s
u
y
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
MerCruiser EFI III (1004)
- MAP
- MAT
- TP
- ECT
- Sea Pump
- Oil Pressure
- Port EMCT
- Starboard EMCT
- Lube Oil Bottle
- Knock 1
- Knock 2
- Fuel Level
- Paddle Wheel/Sea Temp
- Transom Harness
- Pitot
- Steering Angle
- DLC
- CAN Line
x
s - Fuel Injectors 1 – 8
t - Ignition Coils 1 – 8
u - Tach Signal
v - IAC
w - Fuel Pump Relay
x - Boost Fuel Pump
y - Cool Fuel Pump
z - Main Power Relay (MPR)
aa - Trim UP Relay
bb - Warning Horn
cc - Tabs
dd - Key B+
ee - Crank Position Sensor (CPS)
ff - Cam Position Sensor (CMP)
gg - Inputs
hh - PCM 555 Controller
ii - Outputs
jj - Input/Output
EFI SYSTEM COMPONENTS/OPERATION - 1-56
Two-Wire Sensors (ECT and IAT)
The following figure is the schematic of a 2-wire type sensor. This sensor is basically a variable resistor in series with a fixed-known resistor within the computer. By knowing the values
of the input voltage and the voltage drop across the known resistor, the value of the variable
resistor can be determined. The variable resistors that are commonly used are called thermistors. A thermistor’s resistance varies inversely with temperature.
Current
Limiting
Resistor
2-Wire Sensor
Three-Wire Sensors (MAP, TP and FP)
The following figure shows a schematic representation of a 3-wire sensor. All 3-wire sensors
have a reference voltage, a ground and a variable “wiper.” The lead coming off of the wiper
will be the signal to the Engine Control Module (ECM). As this wiper position changes, the
signal voltage returned to the computer also changes.
3-Wire Sensor
1-6 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
7
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-7
8
ECM 555 and PCM 555/03 Identification
Typical ECM Calibration Label
An ECM can be readily identified by the two wire harness connectors
(A–B).
4.3L ALPHA
c
a
864270-3
884521
b
MY2002p5AAAV_0038_4.3_ALPHA_P_AA12345678
Typical ECM Calibration Label
a - Engine Model
b - Calibration Part Number
c - Model Year
Typical PCM Calibration Label
A PCM can be readily identified by the three wire harness connectors (A–B–C).
a - Connector A
b - Connector B
c - Connector C
d - PCM 555
d
a
c b
496 MAG HO
863619-6
859610
MY2002pOAACS_0091_8.1_HOSDM_P_AB12345678
a
b
77498
Typical PCM Calibration Label
a - Engine Model
b - Calibration Part Number
c - Model Year
c
1-8 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
9
Factors Determining Fuel Injector Pulse Width
NOTE: The charts below are shown as examples only and represent no particular engine or
ECM.
MAP & RPM vs Injector on Time
(Base Pulse Width [BPW])
MAP (kPa)
100
90
80
70
60
50
40
30
20
RPM
6
5.5
4
3.5
3
2.75
2.5
2.23
2
1000
BPW in mSec
7
8
9
6.5
7.5
8.5
6
7
8
5.5
6.5
7.5
5
6
7
4.5
5.5
6.5
4
5
6
3.5
4.5
5.5
3
4
5
2000
3000
4000
10.5
10
8
8.5
8
7
6.5
6
5
5000
Base Pulse Width
Multipliers
Water Temp
Deg F
0
50
100
150
Throttle %
25
50
75
100
Air Temp
Deg F
0
50
100
150
MerCruiser EFI III (1004)
Multiplier
2.50
2.00
1.50
1.00
Multiplier
1.50
2.00
2.50
3.00
Multiplier
1.10
1.05
1.00
1.00
EFI SYSTEM COMPONENTS/OPERATION - 1-9
10
1-10 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
11
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-11
12
MEFI-3 and Audio Warning
The MEFI-3 engine’s Audio Warning system will sound the alarm differently and it has more
items that will cause it to sound.
There is what is called a ‘soft’ and a ‘hard’ alarm.
1. Soft Alarm = Below 3000 rpm. Horn on for 1 second, off for 3 seconds, on for 1 second,
off for 3 seconds, etc.
2. Hard Alarm = Above 3000 rpm. Horn sounds all the time.
Audio alarm sounds for the same malfunctions as MEFI-1 and -2;
1. MCM - Low lube level in Gear Lube Bottle. [General 1] or MIE - High Transmission fluid
temperature [General 2].
2. MCM/MIE - Low engine oil pressure.
3. MCM/MIE - Too high engine coolant temperature.
Early production and service ECMs had the following items that will sound the
alarm;
1. MCM/MIE – Horn will sound if there is an active engine Diagnostic Trouble Code [DTC]
that is occurring while the engine is running. The horn will not sound a stored DTC.
Correcting the DTC malfunction will stop the horn.
2. MCM/MIE – Horn will sound if the battery voltage to the ECM is low, [less than 9v for at
least 5 seconds]. Using the throttle lever to increase engine rpm to get the alternator to
put out more voltage will correct most low voltage problems.
3. MCM/MIE – V6 and V8 305/350 cid engines only. Horn will sound if there is low fuel
pressure [for at least 5 seconds]. These engines have a fuel pressure sensor. The EFI
engines have the sensor in the throttle body unit and the MPI engines have the sensor
located in the port fuel rail toward the rear of the engine. Correcting the cause of the low
fuel pressure will stop the horn.
The ECM checksums listed below have these additional alarms turned ON in them.
NOTE: Later production and service replacement ECMs have these extra alarms
turned off. If the ECM checksum is different from the ones listed below, the extra
alarms in that ECM is turned OFF.
MCM 4.3L EFI: ECM never had these extra alarms turned on.
MCM 5.0L EFI: With D04B or D074 checksum.
MCM 5.7L EFI: With D7ED or D798 checksum.
MCM 350 MPI, MCM 350 MPI Horizon, MIE 350 MPI Ski, MIE 350 MPI Inboard or MIE 350
MPI Horizon Inboard: With E60D or EAED checksum.
MIE Black Scorpion: With BB98 or BB42 checksum.
MCM 7.4L MPI or MIE 7.4L MPI Inboard: With FE28.checksum.
MCM 454 MPI, MCM 454 MPI Horizon or MIE 454 MPI Horizon Inboard: With EBC4 checksum.
MCM 502 MPI or MIE 8.2L MPI Inboard: With F02D checksum.
1-12 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
13
Additional MEFI-3 ECM Features
Moving Desired RPM Mode (ECM’s with Delphi #1623999)
A Moving Desired RPM mode has been added to the MEFI-3 ECM. This mode will increase
the desired idle rpm to a calibrated set point according to the throttle position. When the
Throttle Position (TP) sensor is at the closed throttle setting, the ECM will use Idle Air Control
(IAC) and Ignition Control (IC) to maintain the calculated ’desired rpm’. This will make the transition from idle (closed throttle) to higher throttle settings smoother. It will also help maintain
constant low engine speeds from 700 to 1200 rpm. At 5% or greater TP sensor setting, the
Moving Desired RPM mode is not active.
IMPORTANT: An improperly adjusted throttle cable can cause the engine idle rpm to
be higher than the normal 600 rpm even though the control throttle lever is back to the
idle rpm position.
Load Anticipation Mode
The Load Anticipation mode is used on MIE inboard and ski engines only. The function is used
to help inboard engines during shifting. An electrical signal from the neutral safety switch (on
the transmission) goes to the ECM on J2-20. This signal tells the ECM if the switch is closed
or open. In neutral gear, the neutral safety switch is closed (signal grounded). When shifting
into gear, the switch opens (signal open).
When the transmission is shifted into gear, the open signal causes the ECM to add a calibrated amount of bypass air with the IAC. This is done to increase the load handling capability
of the engine when going into gear on larger boats. When shifting back into neutral gear, the
additional IAC bypass air is removed in an attempt to limit engine rpm flares. The amount of
IAC air used is constantly monitored by the ECM. After the transmission is shifted, and the
engine has stabilized, the ECM calculates an ’error band’ from the Moving Desired RPM
mode and adjusts the Load Anticipation mode IAC count accordingly. This allows the ECM
to ’learn’ the best IAC bypass air position to use for shifting each particular boat.
NOTE: The Load Anticipation mode is on MIE 454/502 cid inboard engines also.
Shift Switch Operation
The Shift Switch is used on Alpha models only. The switch is normally ‘closed’, completing
a circuit from the ECM’s J2-9 terminal through the shift switch, to ground. When shifting, the
switch will ‘open’ the J2-9 wire between the ECM and ground. This will cause the ECM to go
and lower the IAC motor count and retard the ignition timing to help the shifting. When the
shift switch is back in the normal position, ignition timing and IAC motor count are restored.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-13
14
ECM/PCM 555 Engine Guardian Strategy & Additional
Guardian Sensors
Engine Guardian is the focal point of the self-diagnostic strategy of ECM/PCM 555. It helps
protect the engine from possible damage that could result from several faulty conditions. The
system monitors the sensors incorporated on the engine and if a malfunction is discovered
a fault description is stored in the PCM and available power is normally reduced. By ensuring
engine output is at a low enough level, the engine is better protected from thermally induced
failures.
For example, if an open or short is found in an exhaust manifold sensor, available power will
be reduced to 90% of total, the warning horn will sound 2 beeps per minute and the MercMonitor gauge (SC1000) will display a warning lamp. In an exhaust manifold overheat condition
the maximum rpm will vary with the temperature of the manifold and could be limited to idle
in extreme cases of overheating, a continuous horn will sound and the SC1000 will display
a warning lamp.
IMPORTANT: Engine Guardian cannot guarantee that engine damage will not occur
when adverse operating conditions are encountered. Engine Guardian is designed to
warn the operator of an adverse condition and to reduce power by limiting rpm in an
attempt to reduce possible engine damage. The boat operator is ultimately
responsible for proper engine operation.
1-14 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
15
ECM 555 Warning System Operation
The engine warning system incorporates an audio alarm and, if installed, Smartcraft Gauges
System. When the key switch is turned to the ON position, the audio alarm will momentarily
activate to test the warning system. The alarm should sound once if the system is operable.
This table is a guick guide, showing what warning output will accompany a fault.
Smartcraft
Gauges
Audio
Alarm
Available
Power
ECT CKT HI
Yes
2 Bp/min
90%
Open
ECT CKT LO
Yes
2 Bp/min
90%
Short
ECT Coolant
Overheat
Yes
Constant
6 - 100 %
EST 1 Open 1
Yes
2 Bp/min
100%
Coil harness wire open
EST 1 Short
Yes
2 Bp/min
100%
Coil harness wire short
Fuel Injector 1-7-4-6
Open
Yes
2 Bp/min
100%
Fuel injector wire open
Fuel Injector 3-5-2-8
Open
Yes
2 Bp/min
100%
Fuel injector wire open
Guardian Strategy
Yes
Constant
IAC Output LO/HI
2
Yes
2 Bp/min
90%
Open
Knock Sensor 1 Lo
Yes
2 Bp/min
90%
Open
Knock Sensor 1 Hi
Yes
2 Bp/min
90%
Short
Low Drive Lube
Strategy
Yes
Constant
100%
Low oil in sterndrive
Low Oil Pressure
Strategy
Yes
Constant
0 - 100%
Fault
1
Description
Engine guardian overheat
condition
0% - 100% Protection Strategy
Low oil pressure strategy
NOTE: If any 5v sensor becomes shorted to ground the engine will not start. If the engine is
operating when the short occurs the engine may stop operating and will not start.
NOTE: 1 GM EFI ignition system failure open or shorted, driver will flag EST 1 fault.
NOTE: 2 TPS must see 5% throttle then back to 0% to flag IAC fault.
NOTE: 3 2-wire sensor open will read sensor Hi on scan tool.
NOTE: 4 VDC PWR Low - if shorted or no voltage engine will not start; if VDC PWR voltage
falls velow 22 volts will set sensor faults.
NOTE: 5 Shift Switch - will activate code when engine rpm are above 3500 rpm and 40% load.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-15
16
ECM 555 Warning System Operation (continued)
Smartcraft
Gauges
Audio
Alarm
Available
Power
Main Power Relay
Output
Yes
No
N/A
Engine will not start
Main Power Relay
Backfeed
Yes
No
N/A
Engine will not start
MAP Sensor 1 Input
High
Yes
2 Bp/min
90%
High voltage or short
MAP Sensor 1 Input
Low
Yes
2 Bp/min
90%
Open, no visual on
SC1000
Oil PSI CKT Hi
Yes
2 Bp/min
90%
Open, defaults to 50.7 psi
Oil PSI CKT Lo
Yes
2 Bp/min
90%
Short, defaults to 50.7 psi
Overspeed
Yes
Constant
rpm limit
Engine over rpm limit
Pitot CKT Hi
No
No
100%
Short or high voltage
Pitot CKT Lo
No
No
100%
Open
Sea Pump PSI Lo
Yes
Constant
6-100%
Sea Pump CKT Hi
Yes
2 Bp/min
90%
Open - 0 psi reading
Sea Pump CKT Lo
Yes
2 Bp/min
90%
Voltage high or short
Sea Water Temp
No
No
N/A
Defaults to –31 degrees C
Fuel Level #1
No
No
N/A
Only if turned on
STB EMCT CKT Hi
N/A
N/A
N/A
N/A
STB EMCT CKT Lo
N/A
N/A
N/A
N/A
STB EMCT CKT
Overheat
N/A
N/A
N/A
N/A
Fault
Description
Guardian Strategy
NOTE: If any 5v sensor becomes shorted to ground the engine will not start. If the engine is
operating when the short occurs the engine may stop operating and will not start.
NOTE: 1 GM EFI ignition system failure open or shorted, driver will flag EST 1 fault.
NOTE: 2 TPS must see 5% throttle then back to 0% to flag IAC fault.
NOTE: 3 2-wire sensor open will read sensor Hi on scan tool.
NOTE: 4 VDC PWR Low - if shorted or no voltage engine will not start; if VDC PWR voltage
falls velow 22 volts will set sensor faults.
NOTE: 5 Shift Switch - will activate code when engine rpm are above 3500 rpm and 40% load.
1-16 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
17
ECM 555 Warning System Operation (continued)
Smartcraft
Gauges
Audio
Alarm
Available
Power
Steer CKT Hi
No
No
100%
Short or high voltage
Steer CKT Lo
No
No
100%
Open
TPS1 CKT or
Range Hi
Yes
2 Bp/min
90%
Short or high voltage
TPS1 CKT or
Range Lo
Yes
2 Bp/min
90%
Open or low voltage
Trim CKT or Range
Hi
Yes
No
100%
Open or high voltage
Trim CKT or Range
Lo
Yes
No
100%
Short
5 VDC PWR Low 4
Yes
2 Bp/min
90%
Short or low - engine may
not start
MAT Sensor Hi
Yes
2 Bp/min
90%
Open default to –32 degrees F
MAT Sensor Lo
Yes
2 Bp/min
90%
Short default to –32 degrees F
Shift Switch 5
Yes
2 Bp/min
90%
Open Circuit
Fault
Description
NOTE: If any 5v sensor becomes shorted to ground the engine will not start. If the engine is
operating when the short occurs the engine may stop operating and will not start.
NOTE: 1 GM EFI ignition system failure open or shorted, driver will flag EST 1 fault.
NOTE: 2 TPS must see 5% throttle then back to 0% to flag IAC fault.
NOTE: 3 2-wire sensor open will read sensor Hi on scan tool.
NOTE: 4 VDC PWR Low - if shorted or no voltage engine will not start; if VDC PWR voltage
falls velow 22 volts will set sensor faults.
NOTE: 5 Shift Switch - will activate code when engine rpm are above 3500 rpm and 40% load.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-17
18
Manifold Vacuum / Pressure Reference Chart
Manifold
Vacuum
psi
Absolute Pressure
psi
kPa
Manifold
Vacuum
Absolute Pressure
psi
psi
kPa
0
14.7
101.3
7 1/4
7.45
51.4
1/4
14.45
99.6
7 1/2
7.2
49.6
1/2
14.2
97.9
7 3/4
6.95
47.9
3/4
13.95
96.2
8
6.7
46.2
1
13.7
94.4
8 1/4
6.45
44.5
1 1/4
13.45
92.7
8 1/2
6.2
42.7
1 1/2
13.2
91.0
8 3/4
5.95
41.0
1 3/4
12.95
89.3
9
5.7
39.3
2
12.7
87.5
9 1/4
5.45
37.6
2 1/4
12.45
85.8
9 1/2
5.2
35.8
2 1/2
12.2
84.1
9 3/4
4.95
34.1
2 3/4
11.95
82.4
10
4.7
32.4
3
11.7
80.6
10 1/4
4.45
30.7
3 1/4
11.45
78.9
10 1/2
4.2
29.0
3 1/2
11.2
77.2
10 3/4
3.95
27.2
3 3/4
10.95
75.5
11
3.7
25.5
4
10.7
73.8
11 1/4
3.45
23.8
4 1/4
10.45
72.0
11 1/2
3.2
22.1
4 1/2
10.2
70.3
11 3/4
2.95
20.3
4 3/4
9.95
68.6
12
2.7
18.6
5
9.7
66.9
12 1/4
2.45
16.9
5 1/4
9.45
65.1
12 1/2
2.2
15.2
5 1/2
9.2
63.4
12 3/4
1.95
13.4
5 3/4
8.95
61.7
13
1.7
11.7
6
8.7
60.0
13 1/4
1.45
10.0
6 1/4
8.45
58.2
13 1/2
1.2
8.3
6 1/2
8.2
56.5
13 3/4
0.95
6.5
6 3/4
7.95
54.8
14
0.7
4.8
7
7.7
53.1
14 1/4
0.45
3.1
14 1/2
0.2
1.4
1-18 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
19
Vacuum Gauge vs MAP Sensor
This graph is correct at Sea Level only.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-19
20
Fuel Systems Diagrams
Multi-Port Injection With Vapor Separator Tank (VST)
g
h
f
e
i
d
b
c
a
73895R2
a
b
c
d
e
f
g
h
i
- Fuel line from boat’s fuel tank
- Water separating fuel filter
- Supply pump (mechanical or electric)
- Vapor separator tank
- Fuel rail
- Fuel injectors (8)
- Fuel pressure regulator
- Vacuum line to intake manifold
- Return line to vapor separator tank
1-20 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
21
350 Magnum Multi-Port Injection with MEFI 3
j
k
h
a
b
c
g
d
f
i
e
74871
350 Mag MPI Shown - Scorpion Is Similar
a
b
c
d
e
f
g
h
i
j
k
- Vacuum Line To Intake Manifold Base
- Fuel Pressure Regulator
- Fuel Cooler
- Electric Fuel Pump
- Water Separating Fuel Filter
- Fuel From Tank
- Direction Of Water Flow
- Fuel Line To Fuel Rail
- Excess Fuel Return To Water Separating Fuel Filter
- Fuel Injectors (8)
- Fuel Rail
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-2122
Throttle Body Injection With Vapor Separator Tank (VST)
e
f
g
d
b
c
a
73895R1
a
b
c
d
e
f
g
- Fuel line from boat’s fuel tank
- Water separating fuel filter
- Supply pump (mechanical or electric)
- Vapor separator tank
- Throttle body with 2 fuel injectors
- Fuel pressure regulator
- Return line to vapor separator tank
1-22 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
23
Throttle Body Injection With Cool Fuel System
i
J
h
e
d
g
f
c
a
b
74871R1
a
b
c
d
e
f
g
h
i
j
- Fuel line from boat’s fuel tank
- Water separating fuel filter
- Electric fuel pump
- Fuel cooler
- Fuel pressure regulator
- Return line to fuel filter
- Water flow through cooler
- Vent line to flame arrestor
- Throttle body with 2 fuel injectors
- “dummy” fuel pressure regulator
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-23
24
Fuel Pressure Regulator Assembly
The pressure regulator is a diaphragm-operated relief valve with fuel pump pressure on one
side, and regulator spring pressure and intake manifold vacuum on the other. The regulator’s
function is to maintain a constant pressure differential across the injectors at all times. The
pressure regulator compensates for engine load by increasing fuel pressure as engine vacuum drops.
If the pressure is too hi or low, poor performance can result.
1-24 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
25
“Cool Fuel” System Fuel Pressure Regulators
There are 3 different “Cool Fuel”, fuel pressure regulators that are used in production. If the
wrong regulator is used on an engine, that engine can have a problem with its fuel supply to
the injectors. When checking regulator pressure on MPI engines, always remove the small
black hose that goes to the regulator before the test. This hose goes to the intake manifold
or plenum and it has vacuum on it, which causes the pressure to read lower at idle RPM. By
removing the hose, the regulator’s true pressure will be shown.
a
b
c
d
e
- Filter
- Fuel Cooler Orifice
- Pressure Regulator
- Screw and Washer
- Fuel Line
75708
There are 2 ways of identifying each regulator by looking at them. By a colored paint mark
on its’ mounting flange and by a small ring that is on the regulator’s hose fitting.
ALL TBI ENGINES AND SMALL BLOCK MPI ENGINES:
(Black Scorpion, with Cool Fuel module on starboard side, has a 43 PSI fuel system)
30 psi (207 kPa)
Paint Mark: Pink
Ring on Regulator’s Hose Fitting: None.
ALL 7.4L MPI (L29) ENGINES AND ALL 454/502 MAG EFI/MPI ENGINES WITH MEFI-3 ECM’S AND
ECM/PCM 555 ENGINES:
43 psi (296 kPa)
Paint Mark: Blue
Ring on Regulator’s Hose Fitting: Green.
ALL 454/502 MAG MPI ENGINES WITH MEFI-1 ECM’S:
36 psi (248 kPa)
Paint Mark: Yellow and Orange
Ring on Regulator’s Hose Fitting: Black.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-25
26
Fuel Pressure Regulator Identification (Revised Aug. 6, 2004)
•
Engine
Model
ECM and PCM 555 Fuel Regulator Identification
Color
Code
System
psi (kPa)
Regulator
P/N
Comments
V6 4.3L, V8 5.7L, 6.2L, ECM 555, (MPI, Cool Fuel, GM MPI intake, GMEFI system).
V6 4.3L, V8
Blue/Brown 43 (296)
861126A 1
Regulator on fuel cooler. Green ring on
5.0L, 350 Mag,
hose fitting.
MX6.2 Models
V8 5.7L, 6.2L, ECM 555, (MPI, Cool Fuel, MerCruiser 320 EFI style intake, plenum, Keihin injectors).
Black Scorpion
Pink
30 (207)
807952A 1
Regulator on fuel cooler. No ring on
(5.7L & 6.2L),
hose fitting.
377 Scorpion
Bravo & Ski
V8 5.0L, 5.7L, 6.2L, ECM 555, (MPI, Gen 3 Cool Fuel, GM MPI intake, GMEFI system).
5.0L MPI, 350 Mag, None
42.5 (288) 892681
Regulator in top of Gen 3 Cool Fuel Module
MX6.2 Models
V8 8.1L, PCM 555, (MPI, Cool Fuel, GM intake, plenum, injectors).
V8 496 Mag,
Blue/Brown 43 (296)
861126A 1
Regulator on fuel cooler. Green ring on
8.1S Models
hose fitting.
V8 8.1L, PCM 555, (MPI, Gen 3 Cool Fuel, GM intake, plenum, injectors).
V8 496 Mag,
None
42.5 (288) 892681
Regulator in top of Gen 3 Cool Fuel Module
8.1S Models
•
Engine
Model
MEFI-1, -2, -3 ECM Fuel Regulator Identification
Color
Code
System
psi (kPa)
Regulator
P/N
V8 5.7L, MEFI-1, (TBI, VST, Non-Gen+ engines, GM TBU).
350 Mag EFI
Unknown
12 (82)
None
Ski
Comments
Regulator in TBU. See SB 94-8.
V6 4.3L, V8 5.0L, 5.7L, MEFI-1, (TBI, VST, Non Gen+ and Gen+ engines, GM TBU).
All V6 EFI, all
Unknown
30 (207)
852955
Regulator in TBU
V8 EFI models
V6 4.3L, V8 5.0L, 5.7L, MEFI-1, -3, (TBI, Cool Fuel engines, GM TBU).
All V6 EFI, all
Unknown
30 (207)
852955
Regulator in TBU
V8 EFI models
V8 5.7L, MEFI-1, (MPI, VST, Non-Gen+ engines, Keihin injectors).
350 Mag MPI
Unknown
43 (296)
806808A 2
Regulator on the fuel rail.
Bravo, Ski
V8 5.7L, MEFI-1, (MPI, VST, Gen+ engines, Keihin injectors).
350 Mag MPI
Unknown
43 (296)
806808A 2
Bravo
Regulator on fuel rail.
V8 5.7L, MEFI-1, (MPI, Cool Fuel on Starboard side, Gen+ engines, Keihin injectors).
Black Scorpion
Unknown
43 (296)
808062A 1
Regulator on fuel rail.
Ski (5.7L)
1-26 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
27
•
Engine
Model
MEFI-1, -2, -3 ECM Fuel Regulator Identification - Contd.
Color
Code
System
psi (kPa)
Regulator
P/N
Comments
V8 5.7L, MEFI-1, (MPI, Cool Fuel on Port side, Gen+ engines, Keihin injectors).
350 Mag MPI
Pink
30 (207)
807952A 1
Regulator on fuel cooler. No ring on hose
Bravo, Inbrd, Ski,
fitting.
Black Scorpion
Ski
V8 5.7L, 6.2L, MEFI-2, -3, (MPI, Cool Fuel on Port side, Gen+ engines, Magneti-Marelli injectors).
350 Mag MPI
Pink
30 (207)
807952A 1
Regulator on fuel cooler. No ring on hose
Alpha, Bravo,
fitting.
Inbrd, Ski, and
MX 6.2 MPI
Bravo, Inbrd
V8 5.7L, 6.2L, MEFI-3, (MPI, Cool Fuel on Port side, Gen+ engines, Keihin injectors).
Black Scorpion
Pink
30 (207)
807952A 1
Regulator on fuel cooler. No ring on hose
(5.7L & 6.2L)
fitting.
V8 7.4L (L29), MEFI-2, -3, (MPI, Cool Fuel, GM MPI intake, plenum, injectors).
7.4L MPI
Blue/Brown 43 (296)
861126A 1
Regulator on fuel cooler. Green ring on hose
Bravo & Inbrd
fitting. GM regulator on the fuel rail does not
operate or control fuel psi.
V8 7.4L MEFI-1, (GM TBI, Cool Fuel, GM TBI intake, GM TBU).
7.4LX EFI Bravo, Pink
30 (207)
807952A 1
Regulator on fuel cooler. No ring on hose
7.4L EFI Inbrd
fitting.
V8 7.4L, 8.2L, MEFI-1, (MPI, VST, MerCruiser MPI intake, Keihin injectors).
All 7.4L & 8.2L
Unknown
36 (248)
805227A 1
Regulator on fuel rail. Hose fitting points toward
MPI models
port side.
V8 7.4L, 8.2L, MEFI-1, (MPI, Cool Fuel, MerCruiser MPI intake, Keihin injectors).
All 7.4L & 8.2L
Yellow/
36 (248)
860349A 1
Regulator on fuel cooler. Black ring on hose
MPI models
Orange
fitting. Regulator on fuel rail does not control
fuel pressure.
V8 7.4L, 8.2L, MEFI-3, (MPI, Cool Fuel, MerCruiser MPI intake, Magneti-Marelli injectors).
All 7.4L & 8.2L
Blue/
43 (296)
861126A 1
Regulator on fuel cooler. Green ring on hose
All 7.4L & 8.2L
fitting. No regulator on the fuel rail.
V8 8.2L, MEFI-3, (MPI, Cool Fuel, MerCruiser MPI intake).
HP500 EFI
Blue/
43 (296)
861126A 1
Brown
[1999-UP]. Green ring on hose fitting.
V8 8.2L, MEFI-3, (Dual TBI, Cool Fuel, Super Charger intake, GM TBU).
HP575 SCi
Pink
30 (207)
807952A 1
[2000-UP].No ring on hose fitting.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-27
28
Fuel Injectors
The EFI injector assembly is a solenoid-operated device, controlled by the ECM, that meters
pressurized fuel to engine cylinders. The ECM grounds the injector solenoid, which opens
a valve, allowing fuel to flow past the valve. The injector tip has holes that control the fuel flow,
generating a conical spray pattern of finely atomized fuel at the injector tip. On throttle body
systems, fuel is directed into the bore of the Throttle Body Assembly, and then it passes into
the intake manifold.
On MPI models, fuel is directed at the intake valve, causing it to become further atomized and
vaporized before entering the combustion chamber.
Throttle Body Injection (TBI) Fuel Injector
Multi-Port Injection (MPI) Fuel Injector
s
r
q
a b c d e f g h i j k l mn o p q r s -
Needle Valve
Nozzle
Cap
O-Ring
Valve Stopper
Core
O-Ring
Spring
Housing
Solenoid Coil
Tape
Bobbin
O-Ring
Inner Collar
Sleeve
Terminal
Connector
Filter
O-Ring
p
o
n
l
k
m
J
i
g
h
f
e
d
c
b
a
Early 454/502 Models
1-28 - EFI SYSTEM COMPONENTS/OPERATION
72970
7.4L (454 c.i.) L-29 Models
MerCruiser EFI III (1004)
29
Fuel Injector Identification (Revised Aug. 6, 2004)
•
Engine
Model
ECM and PCM 555 Engine Injector Identification
Color
Code
System
psi (kPa)
Injector
P/N
[Manufacture] Comments
V6 4.3L, V8 5.7L, 6.2L, ECM 555, (MPI, Cool Fuel, GM MPI intake, GMEFI system).
V6 4.3L, V8
Neutral Tip 43 (296)
885176
[GM].
5.0L, 350 Mag,
MX6.2 Models
V8 5.7L, 6.2L, ECM 555, (MPI, Cool Fuel, MerCruiser 320 EFI style intake, plenum, Keihin
injectors).
Black Scorpion
White Tip
30 (207)
805225A 1
[Keihin].
(5.7L & 6.2L)
V8 8.1L, PCM 555, (MPI, Cool Fuel, GM intake, plenum, injectors).
V8 496 Mag,
Black Tip
43 (296)
881693
[GM]. Delphi.
8.1S Models
Neutral Tip 43 (296)
881693
[GM]. Delphi.
•
Engine
Model
MEFI-1, -2, -3 ECM Engine Injector Identification
Color
Code
System
psi (kPa)
Injector
P/N
[Manufacture] Comments
V8 5.7L, MEFI-1, (TBI, VST, Non-Gen+).
350 Mag EFI
Blue/Black
12 (82)
None
[GM]. See SB 94-8.
Ski
V6 4.3L, V8 5.0L, 5.7L, MEFI-1, (TBI, VST and Cool Fuel, Non-Gen+ and Gen+ engines).
All V6 EFI, all
Pink/Purple 30 (207)
852956
[GM].
V8 EFI models
V8 5.7L, MEFI-1, (MPI, VST, Non-Gen+).
350 Mag MPI
Orange Tip 43 (296)
Bravo, Ski
806807A 1
[Keihin].
V8 5.7L, MEFI-1, (MPI, VST, Gen+).
350 Mag MPI
Orange Tip 43 (296)
Bravo
806807A 1
[Keihin].
V8 5.7L, MEFI-1, (MPI, Cool Fuel on Starboard side, Gen+).
Black Scorpion
Orange Tip 43 (296)
806807A 1
Ski (5.7L)
[Keihin].
V8 5.7L, 6.2L, MEFI-1, -3, (MPI, Cool Fuel on Port side, Gen+).
350 Mag MPI
White Tip
30 (207)
805225A 1
[Keihin].
Bravo, Inbrd, Ski,
Black Scorpion
Ski (5.7L & 6.2L),
377 Scorpion
Bravo & Ski
1-30 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
30
•
MEFI-1, -2, -3 ECM Engine Injector Identification - Contd.
Engine
Model
Color
Code
System
psi (kPa)
Injector
P/N
[Manufacture] Comments
V8 5.7L, 6.2L, MEFI-2, -3, (MPI, Cool Fuel on Port side, Gen+).
350 Mag MPI
None
30 (207)
861260T
[Magneti-Marelli].
Alpha, Bravo,
Inbrd, Ski, and
MX 6.2 MPI
Bravo, Inbrd
V8 7.4L (L29), MEFI-2, -3, (MPI, Cool Fuel, GM MPI intake, plenum, injectors).
7.4L MPI
Olive Green 43 (296)
802632
[GM].
Bravo & Inbrd
Band on Tip
V8 7.4L MEFI-1, (GM TBI, Cool Fuel, GM TBI intake).
7.4LX EFI Bravo, Yellow/Black 30 (207)
853998
7.4L EFI Inbrd
[GM].
V8 7.4L, 8.2L, MEFI-1, (MPI, VST and Cool Fuel, MerCruiser MPI intake).
All 7.4L & 8.2L
White Tip
36 (248)
805225A 1
[Keihin].
MPI models
V8 7.4L, 8.2L, MEFI-3, (MPI, Cool Fuel, MerCruiser MPI intake).
All 7.4L & 8.2L
None
43 (296)
861260T
[Magneti-Marelli].
All 7.4L & 8.2L
V8 8.2L, MEFI-3, (MPI, Cool Fuel, MerCruiser MPI intake).
HP500 EFI
(Unknown) 43 (296)
849896
[1999-UP, GM].
V8 8.2L, MEFI-3, (Dual TBI, Cool Fuel, Super Charger intake, GM TBU).
HP575 SCi
Yellow/Black 30 (207)
853998T
[2000-UP GM].
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-31
31
Engine Wiring Diagrams
MEFI 3 MCM 5.0L EFI, 5.7L EFI and 350 Mag MPI Engines
c
b
90 Amp
Fuse
a
76061
A - Audio Warning Components
1. - Oil Pressure Switch
B - Instrumentation Components
1. - Oil Pressure Sender
2. - Trim Sender
a - Positive Power Wire To
EFI System Harness
b - Harness Connector To
EFI System Harness
c - Auxiliary Tachometer Lead
1-32 - EFI SYSTEM COMPONENTS/OPERATION
C - Charging and Starting Components
1. - Alternator
2. - Ground Stud
3. - Starter
4. - Circuit Breaker
5. - Starter Slave Solenoid
6. - Jumper Wire Connection
7 - Battery
7.
MerCruiser EFI III (1004)
32
MEFI 3, 350 Magnum MPI and All Black Scorpion Engines
NOTE: All BLACK wires with a ground symbol are interconnected within the EFI system
harness.
NOTE: Component position and orientation shown is arranged for visual clarity and ease of
circuit identification.
1. - Fuel Pump
2. - Distributor
3. - Coil
4. - Knock Sensor (KS) Module
5. - Data Link Connector (DLC)
6. - Manifold Absolute Pressure (MAP) Sensor
7. - Idle Air Control (IAC)
8. - Throttle Position (TP) Sensor
9. - Engine Coolant Temperature (ECT) Sensor
10. - Electronic Control Module (ECM)
11. - Fuel Pump Relay
12. - Ignition/System Relay
BLK
BLU
BRN
GRY
GRN
ORN
PNK
PUR
RED
TAN
WHT
YEL
LIT
DRK
=
=
=
=
=
=
=
=
=
=
=
=
=
=
13. - Fuse (15 Amp) Fuel Pump,
Fuse (15 Amp) ECM/DLC/Battery, Fuse (10
Amp) ECM/Injector/Ignition/Knock Module
14. - Harness Connector To Starting/Charging
Harness
15. - Positive (+) Power Wire To Engine Circuit
Breaker
16. - Shift Plate (Not used on Ski models)
17. - Oil Pressure (Audio Warning System)
18. - Gear Lube Bottle (Not used on Ski models)
19. - Fuel Pressure Switch
20. - Water Temperature Sender
BLACK
BLUE
BROWN
GRAY
GREEN
ORANGE
PINK
PURPLE
RED
TAN
WHITE
YELLOW
LIGHT
DARK
(–)
(+)
MerCruiser EFI III (1004)
76064
EFI SYSTEM COMPONENTS/OPERATION - 1-33
33
ECM Wiring Diagram – MEFI 3 (V6 and Small Block V8) (1 of 4)
INJECTORS - ONE IF EFI, FOUR IF MPI
(INJECTORS 2, 3, 5, 8 - IF FOUR)
From
INJ/
ECM
FUSE
10 AMP
481
BLK
439 PNK
J1-1
467 DK BLU
INJECTORS - ONE IF EFI, FOUR IF MPI
(INJECTORS 1, 4, 6, 7 - IF FOUR)
15A
481
BLK
468 DK GRN
J1-17
From
B+
439 PNK
2
465 DK GRN/WHT
J1-23
339 PNK
15A
ECM
87a 30 85 86 87
150
BLK
IDLE AIR
CONTROL
(IAC) VALVE
441 BRN OR BLU/WHT
J1-28
442 RED OR BLU/BLK
J1-12
443 YEL OR GRN/WHT
J1-11
444 GRN/BLK
J1-27
461 ORN
916 YEL
J1-32
SERIAL DATA
J2-21
MASTER/SLAVE
J2-22
DIAGNOSTIC “TEST”
TERMINAL
150 BLK
DLC
450 BLK
FROM
ECM/BAT
FUSE
15A
440 ORN
451 BLK/WHT
419 BRN/WHT
J1-9
MALFUNCTION INDICATOR
LAMP
76097
1-34 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
34
ECM Wiring Diagram – MEFI 3 (V6 and Small Block V8) (2 of 4)
472 TAN
INTAKE AIR
TEMPERATURE (IAT)
J2-30 INTAKE AIR TEMPERATURE
(IAT) SENSOR SIGNAL
813 BLK
813 BLK
813 BLK
B
SENSOR GROUND
813 BLK
C
(TP)
J2-3
417 DK BLU
J2-26
A
416 GRY
J2-4
475 GRN
J2-12
416 GRY
J2-19
432 LT GRN
J2-27
814 BLK
J2-18
B
FUEL PRESSURE
SENSOR (FP)
C
FUEL PRESSURE
SENSOR SIGNAL
A
ECM
813 BLK
814 BLK
814 BLK
ENGINE COOLANT
TEMPERATURE (ECT)
410 YEL
J2-11
496 DK BLU
J1-30
114 BLU
ENGINE COOLANT
TEMPERATURE (ECT)
SENSOR SIGNAL
KNOCK SENSOR 1
J2-7
OIL PRESSURE
SWITCH
J2-24
LUBE BOTTLE
J2-9
SHIFT INTERRUPT
SIGNAL
KNOCK
SENSOR 1
906 TAN/WHT
150 BLK
150 BLK
SHIFT SWITCH
B
A
207 PPL
76098
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-35
35
ECM Wiring Diagram – MEFI 3 with Mercury Distributor
(V6 and Small Block V8) (3 of 4)
TO FUEL PUMP RELAY
FUSE
440 0RN
J2-1
2 RED
ECM BAT FUSE/
DLC 15A
TO
B+
TO
B+
B
2 RED
A
2 RED
3 PNK
440 0RN
BATTERY
FEED
TO DLC
CONNECTOR
SYSTEM/IGNITION RELAY
IGN / INJ FUSE
30
87
86
85
902 RED
439 PNK
J2-32
IGNITION
150
BLK
T0 INJECTORS
AND
FUEL PUMP RELAY
902 RED
WHT/GRN
450
BLK
J1-4
ECM
GROUND
450
BLK
J1-5
ECM
GROUND
450
BLK
J1-20
ECM
GROUND
J2-10
DIST. REF.
J1-2
IGN. COIL
WHT/RED
ECM
DISTRIBUTOR
439 PNK
430 PPL/WHT
902 RED
+
–
121 WHT
121 WHT
IGNITION
COIL
TEMP SENDER
121 WHT
TO IGN
TO TEMP GAUGE
TO TACH
208 BRN
J2-20
LOAD ANTICIPATION
J2-8
TRANSMISSION
OVERTEMP
AUDIO WARNING
CIRCUIT
A
F
901 TAN
B
E
3 PNK
C
D
PUR
C
D
TAN/BLU
TO AUDIO WARNING HORN
TAN
B
E
BLU/TAN
TO TRANSMISSION TEMP SWITCH
GRY
A
F
YEL/BLK
T0 TRANSMISSION
585 TAN/WHT
29 DK GRN
CONNECTOR HALVES
J1-26
76099
1-36 - EFI SYSTEM COMPONENTS/OPERATIO
MerCruiser EFI III (1004)
ECM Wiring Diagram – MEFI 3 with GM EST Distributor
(V6 and Small Block V8) (4 of 4)
TO FUEL PUMP RELAY
FUSE
440 0RN
J2-1
2 RED
ECM BAT FUSE/
DLC 15A
TO
B+
TO
B+
B
2 RED
A
2 RED
440 0RN
BATTERY
FEED
TO DLC
CONNECTOR
SYSTEM/IGNITION RELAY
IGN / INJ FUSE
902 RED
439 PNK
150
BLK
3 PNK
J2-32
IGNITION
TO INJECTORS
902 RED
TO FUEL
PUMP RELAY
TO IGNITION
COIL TERM
FROM
IGNITION
RELAY
J1-4
450
BLK
J1-5
ECM
GROUND
450
BLK
J1-20
ECM
GROUND
423 WHT
J1-10
IGNITION
CONTROL
430 PUR/WHT
J2-10
DIST. REF. HIGH
424 TAN/BLK
J1-24
BYPASS
453 RED/BLK
J1-3
DIST. REF. LOW
J2-20
LOAD ANTICIPATION
J2-8
TRANSMISSION
OVERTEMP
J1-26
AUDIO WARNING
CIRCUIT
902 RED
121 WHT
TEMP SENDER
TO IGN
TO TEMP GAUGE
TO TACH
ECM
GROUND
ECM
450
BLK
208 BRN
A
F
901 TAN
B
E
3 PNK
C
D
PUR
C
D
TAN/BLU
TAN
B
E
BLU/TAN
GRY
A
F
YEL/BLK
585 TAN/WHT
29 DK GRN
CONNECTOR HALVES
76099
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-37
PCM 555 – Charging Harness
3
2
10
4
1
5
8
6
7
TAN
GRY
BLK
LT BLU
YEL/RED
BRN/
WHT
RED/PPL
PPL
TAN/BLU
TAN/BLU
C D
BLU/TAN
E
ORA
YEL/RED
PPL
RED/PPL
BLK
NOT USED
BATT.
NOT USED
OIL
SENDER
BLU/TAN
TRIM
SENDER
AUX
TACH
BREAKER
CIRCUIT
GROUND
LT BLU
YEL/RED
GRY
77671
SOLENOID
SLAVE
GRY
MIE
TRANSMISSION
SWITCH
BLK
BLU/TAN
YEL/RED
BLK
MERCATHODE
GROUND
ORA
BRN/WHT
BRN/WHT
POWER
GRY
BRN/WHT
LT BLU
BLK
BLK
BLK
BLK
RED
RED/PPL
RED/PPL
RED/PPL
YEL/BLK
BLK
RED/PPL
ALTERNATOR
STARTER
RED
PCM
B
PPL
HARNESS
A
TAN
MerCruiser EFI III (1004)
1-38 - EFI SYSTEM COMPONENTS/OPERATION
GRY
PCM 555 – 10 Pin Harness Circuit
B
4
5
6
7
8
1
9 10 11 12 13 14 15 16
3
4
5
A
6
7
8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
WHT
17 18 19 20 21 22 23 24
2
BRN
1
3
1
2
3
4
5
6
7
8
9 10 11
12 13 14 15 16 17 18 19 20 21
22 23 24 25 26 27 28 29 30 31 32
PNK
C
2
c
d
ANALOG
COOLANT
BRN
TAN/BLK
PNK
a
WHT
b
SPLICE 102
TAN
e
A B C D F
MERC
77684
HARNESS
a
b
c
d
e
- Tachometer Signal
- Analog Coolant
- 12 Volt Power
- Audio Warning Alarm
- Neutral Start Switch
The 10 pin harness (MERC harness) is the connecting point between the Mercury MerCruiser
electronic EFI harness and the 10 pin engine harness. It supplies the PCM with the analog
coolant, tachometer, audio warning alarm and neutral safety signals.
A malfunction of the 10 pin harness connection will not set a fault.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-39
PCM 555 – Crank Position and Camshaft Position Circuits
B
3
4
5
6
7
8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
PPL/WHT
e
1
2
1
3
4
5
6
7
8
9 10 11
12 13 14 15 16 17 18 19 20 21
22 23 24 25 26 27 28 29 30 31 32
BLK/PNK
2
TAN
1
A
GRY
C
SPLICE 100
d
SPLICE 101
b
a
b
c
d
e
GRY
BLK/BRN
BLK/BRN
GRY
c
A B C
A B C
CAM
POS
CRANK
POS
e
a
77680
- Crankshaft Position Sensor
- Camshaft Position Sensor
- 5 Volt Power
- 5 Volt Ground
- Signal To The PCM
The crankshaft position sensor, located at the rear of the engine, and the camshaft position
sensor, located at the front of the engine, supply the PCM with timing and rpm information.
If a failure occurs in these sensor circuits, the engine will operate extremely rough or stop
operating. Check for continuity between the PCM and the sensor.
The normal resistance values for these sensors at 21 degrees C (70 degrees F) are:
•
Camshaft Position Sensor - A to B 24.04 mohms and B to C 24.05 mohms
•
Crankshaft Position Sensor - A to B 23.2 mohms and B to C 23.21 mohms.
With software prior to level 091, a malfunction of the crankshaft position sensor or the
camshaft position sensor will not set a fault. With level 091 software, if the camshaft position
sensor is bad and does not send a signal to the PCM, the engine will backfire and not start.
Stop cranking the engine when this occurs and then try to start the engine. Operate the engine
for 20 seconds to set faults. The Audio Warning alarm will signal 2 beeps per minute. The
Smartcraft system monitor will show the check engine light.
1-40 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
GRN/BLK
AB
2
AB
PNK/WHT
SPLICE
5
RED/BLK
SPLICE
BLK
BLU/WHT
a
PNK
PNK/WHT
BLK/WHT
AB
7
BLU/BLK
PNK/BLK
F G H J K
YEL/BLK
AB C D E
PCM 555 – Fuel Injector Harness
2
PNK
PNK
PNK/WHT
8
A B
6
AB
PNK/WHT
A B
3
b
AB
1
4
b
AB
PNK
PNK/WHT
a - Injector Harness To Engine Harness Connector
b - Individual Injector Connectors
77696
The fuel injectors receive fused 12 volt power from Splice 108 (Pins J and K) on the injector
harness. The PCM signals the injector to fire by pulling the 12 volts to ground and completing
the circuit. The normal resistance at 21 degrees C (70 degrees F) is 12.5 ohms.
A malfunction in the fuel injector harness will set the fault of FINJ 1-8 Open or FINJ 1-8 Short.
When the fuel injector driver wire is shorted to ground, the scan tool will read Open Sensor,
this means that the fuel injector is full Open.
When the fuel injector is shorted, the scan tool will read Short Injector.
A shorted 12 volt fuel injector power lead will blow the injector fuse E-F; the scan tool will read
Bad Fuel Pump Fuse.
Fuel Injector Number
1
2
3
4
5
6
7
8
MerCruiser EFI III (1004)
Wire Colors on Fuel
Injector Harness
BLK
GRN/BLK
PNK/BLK
BLU/BLK
BLK/WHT
YEL/BLK
RED/BLK
BLU/WHT
PCM Pinout
C-6
C-11
B-22
B-20
C-23
C-21
C-5
C-3
EFI SYSTEM COMPONENTS/OPERATION - 1-41
PCM 555 – Ignition Circuit
CAM
H
C
B
A
PPL/WHT
BLK/BRN
GRY
WHT/LT BLU
WHT
F G
WHT/RED
BRN
BLK
BLK/WHT
A B C E
RED
COILS 2
SPLICE
101
SPLICE
105
IGNITION
KEY ON
SPLICE
100
C
2
1
9
3
B
4
5
6
7
8
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
2
1
9
3
SPLICE
106
4
5
A
6
7
8
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
2
1
3
4
5
6
7
8
9
10 11
12 13 14 15 16 17 18 19 20 21
22 23 24 25 26 27 28 29 30 31 32
SPLICE
100
WHT/PPL
SPLICE
101
BLK/BRN
GRY
WHT/RED
WHT
F G
TAN
A B C E
RED
WHT/BLK
BRN
SPLICE
105
WHT/PPL
BLK
BLK
BLK
WHT/BLK
SPLICE
106
H
C
B
A
CRANK
COILS 1
77672
POS
With initial key ON, 12 volt power is sent from the battery through the purple lead in the 10-pin
harness to the pink lead at Engine Harness Pin C. This is wake up power to the PCM. The
PCM powers pin B4 which in turn pulls the MPR low. The MPR powers the coils through Splice
105 and powers the engine for ignition.
PCM Pinout
Cyl. Number
PCM Pinout
Cyl. Number
PCM Pinout
Cyl. Number
B2
1
C8
4
B9
7
C7
2
C13
5
C14
8
B10
3
C12
6
1-42 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
A B C D
PCM 555 – Coil Harness Circuit
RED
BRN
BLK
A B C D
d
e
GRN
PNK
PNK
BLK
BRN
PNK
BRN
A B C
D
a
E F G
BRN
H
PNK
BRN
BLK
PNK
A B C D
cBRN
SPLICE
PNK
BLU
PNK
PUR
BRN
BLK
A B C D
SPLICE
b
77695
a
b
c
d
e
- Coil Harness To Engine Harness Connector
- 1 And 8 Coil Connector
- 3 And 6 Coil Connector
- 5 And 4 Coil Connector
- 7 And 2 Coil Connector
There are 2 coil harnesses on the engine, one for each side of the engine. The harnesses
are wired identically. The signal wire color for coils 1 and 8 is BLU, coils 3 and 6 is PUR, 5
and 4 wire is GRN, and 7 and 2 is RED The PNK wire is 12 volt power, the BRN wire is 5 volt
power and the BLK wire is ground. If a possible problem is suspected in the ignition system,
check for faults once with key ON and once with engine running. An EST Open will only
register a fault in a key ON only state and an EST Short will only register with the engine
operating.
A malfunction in the coil harness will set the fault of EST 1-8 Open or EST 1-8 Short.
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-43
MEFI III to IV Conversion Kits
• Project Objectives
– Provide long term resolution to
availability issues with MEFI III
ECM
– Prioritize highest volume service
ECMs for conversion
– started in 2004 season
MEFI III to IV Conversion Kits
• System Overview
– MEFI IV ECM which physically appears the
same as a MEFI III
• Pin out locations are different
• Coil driver is not internal
– Calibrations have been directly converted into
MEFI IV code
MEFI III to IV Conversion Kits
•
•
Kit Components
– MEFI IV ECM
– Cross-Over harness
– Secondary harnesses
– Coil driver with heat sink
– Coil driver bracket
– Hardware
– Instruction sheet
Kit Models
– 350 MPI & MIE 350 MPI FWC
– 6.2 MPI
– 7.4 MPI & MIE 7.4 MPI FWC
– 454 MPI & MIE 454 MPI FWC
– 502/8.2 MPI & MIE 8.2 MPI FWC
– 4.3 EFI
– 5.0 EFI
– 5.7 EFI
– MEFI III remans to remain for Black Scorpion and some High Perf models
MEFI III to IV Conversion Kits
•
Installation Big Block
–
Mount the MEFI IV ECM with existing hardware
– Connect the J1 & J2 connections on the crossover harness
– Connect ground wire to flywheel housing bolt that has no other ground
connection on it
MEFI III to IV Conversion Kits
Big Block
MEFI III to IV Conversion Kits
Big Block
MEFI III to IV Conversion Kits
Big Block
MEFI III to IV Conversion Kits
•
Installation Small Block
– Mount the MEFI IV ECM with existing hardware
– Connect the J1 & J2 connections on the crossover harness
– Mount coil driver/bracket to relay bracket
• Alpha requires spacer and screw provided
• Bravo remove and retain rear MerCathode and rear relay bracket screw for
mounting
– MPI models connect coil driver harness to crossover harness then to coil driver
– EFI models connect coil driver Y harness to crossover harness then to coil driver
• Route Y harness to cool fuel box
• Disconnect engine harness from fuel pump
• Connect male connector of the Y harness to fuel pump
• Connect female connector of the Y harness to the male engine harness
connector
MEFI III to IV Small Block Kit
Harnesses
MEFI III to IV Conversion Kits
•
Service Diagnostic Tools
– CDS version 3.14 or higher
(Version 4.18 or higher for fuel pressure data stream correction)
– MerCruiser Scan Tool version 4.0
(Refer to bulletin number 2001-1)
– THE DDT WILL NOT COMMUNICATE WITH THIS ECM (N0 UPDATE
CARTRIDGE WILL BE AVAILABLE)
Gen II I Cool Fuel System
System features:
·
Single Integrated Module
- Filter, pumps, pressure regulator and cooler, all in one unit
- Fuel flows through filter before getting to lift pump
·
More Reliable
- Fewer components
- Fewer fuel paths
·
Better Accessibility
·
“Production-Friendly”
- Eliminates installation of separate pre-filter at OEM
·
Re-usable, consumer serviceable filter element
- Pull element, dump water, re-install, continue voyage
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-55
This system will be standard on:
·
Small-Block MPI V8 Bravo
·
Small-Block MPI MIE
·
Big-Block MPI Sterndrive
·
Big-Block MPI MIE
It will not be available on:
·
V6 Sterndrive
·
Small-Block Ski
·
Small-Block Alpha
System Overview
·
Water Separating Filter Element
·
2 pumps – Lift & Pressure
- Lift pump - Gerotor
- Pressure pump – Turbine
·
Fuel Pressure Regulator
- New 288 kpa (~42 psi) regulator
- O-rings seal between OD on regulator and ID in cover, rather than a face
seal and return hose
- Regulator dumps excess fuel to inlet side of pressure pump
- Fuel pressure vs. flow characteristics differ slightly from Gen II, requires
minor calibration changes
·
Internal Low Pressure Relief Valve
- Limits pressure across lift pump to 10 psi +/- 5 psi
- Dumps fuel to inlet side of filter
1-56 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
System Module Features:
·
Dual Pump Configuration
- Improved Vapor Lock resistance compared to engines equipped with current
boost pumps
·
Corrosion Protection
- Strontium-coated Internal water passage (same as outboards)
- External housing e-coated
·
Engine Installation
- Low profile water connection, disconnect as required during engine
installation
- 3/8 NPTF thread inlet fuel connection
·
Service Access
- Modules located above front engine mount brackets in all applications
·
Water Jacketed
- Parallel water flow through module permits smaller module
·
Pumps immersed in fuel and draw from bottom of cavity
- Vapor rises to top of cavity, pumps always draw liquid
- Reduced pump noise – not audible over engine at idle
·
No external lines between filter, boost pump, pressure pump, and regulator
- Eliminates 20 external fuel connectors
·
5 seals, not counting inlet and outlet
- Filter cap – Modified SAE o-ring seal
- Module Cover – Controlled-Crush quad ring
- Pressure Regulator – Diametric o-ring
- Pressure Relief Valve – Diametric o-ring
- Harness – Fuel-tight pass-through fitting
·
Self-Draining
- Drains when seawater pump outlet is drained
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-57
System Overview:
Heat Exchanger
(housing - casting)
Fuel pressure
Regulator
Water Outlet
Low pressure
pump
Fuel Filter
High Pressure
Pump
Check Valve
(in pump)
To Engine
(Fuel Rail)
Water Inlet
1st stage relief
(10 psi)
Pressure
Regulator
Water Separating
Fuel Filter
Water Jacket
High Pressure
Pump
1-58 - EFI SYSTEM COMPONENTS/OPERATION
Lift Pump
( Boost Pump)
MerCruiser EFI III (1004)
Fuel Flow Through the System
"2-Story" Water Flow Path
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-59
Cool Fuel III System - Mounted on Small-Block Engine
1-60 - EFI SYSTEM COMPONENTS/OPERATION
MerCruiser EFI III (1004)
Gen III Cool Fuel Module
MerCruiser EFI III (1004)
EFI SYSTEM COMPONENTS/OPERATION - 1-61
Service Bulletin
Bulletin No. 2004-06
Circulate to:
Sales Manager
Accounting
Service Manager
Technician
Parts Manager
Gen III Cool Fuel Module Diagnostics
Models Affected
Application
Model
Serial Number
MCM
496 Mag
0W060000 and above
All Bravo
5.0L MPI
0W060000 and above
All Bravo
350 Mag MPI
0W060000 and above
All Bravo
6.2L MPI
0W060000 and above
MIE
8.1L (all)
0W090000 and above
MIE
350 Mag MPI
0M398372 and above
MIE
6.2L MPI
0M398395 and above
Situation
A new generation of the MerCruiser fuel cooling system has been developed and released
into production. The Generation III Cool Fuel System incorporates many design elements.
The following information is provided for maintenance and troubleshooting of the
Generation III Cool Fuel Module. Upon completion of these tests, if a problem exists,
replace the complete Cool Fuel Module assembly.
Changing Water Separating Fuel Filter Element
! WARNING
Avoid Fire or Explosion: The fuel injection system is pressurized during operation. Use
care when removing the water separating fuel filter. Allow the engine to cool down before
attempting to remove the water separating fuel filter in the following procedure.
! WARNING
Be careful when changing the water separating fuel filter. Gasoline is extremely
flammable and highly explosive under certain conditions. Ensure the ignition key is
"OFF". Do not smoke or allow spark or open flame in the area when changing the fuel
filter. Wipe up any spilled fuel immediately.
THE INFORMATION IN THIS DOCUMENT IS CONFIDENTIAL AND PROTECTED BY COPYRIGHT AND IS THE PROPERTY OF MERCURY MARINE.
This document is provided for the sole and exclusive use of the original recipient as prescribed by Mercury Marine and may not be distributed or copied, digitally or otherwise,
without the prior written consent of Mercury Marine.
2004-06R SEPTEMBER 2004
© 2004 Mercury Marine
Page 1 / 4
Gen III Cool Fuel Module Diagnostics
! WARNING
Ensure that no fuel leaks exist before closing the engine hatch.
1. Allow the engine to cool down.
NOTE: Mercury MerCruiser recommends that the engine be shut off for 12 hours prior to
filter removal.
2. Disconnect the Cool Fuel Module harness from the engine wiring harness.
3. Turn the key switch to the start position and allow the starter to operate for 5 seconds
to relieve fuel system pressure.
4. Turn key switch to off position.
5. Loosen each filter assembly retaining screw until the screw is disengaged from the Cool
Fuel Module. Do not remove the filter assembly retaining screws from the filter cap.
d
c
e
b
h
f
g
a
8837
abcd-
Cool Fuel Module
Cool Fuel Module harness
Filter cup
Filter assembly retaining screw
efgh-
Fuel filter element
Filter cup
Cool Fuel Module filter reservoir
O-ring
6. Unseat the filter assembly by grasping the filter assembly handle and pulling upward.
Do not remove the filter assembly from the Cool Fuel Module at this time.
7. Allow any fuel that may be in the filter assembly to drain out through the bottom of the
filter assembly and into the Cool Fuel Module filter reservoir.
8. Remove the filter cup from the filter cap by grasping the filter cap and rotating it in a
clockwise direction while holding the filter cup stationary.
THE INFORMATION IN THIS DOCUMENT IS CONFIDENTIAL AND PROTECTED BY COPYRIGHT AND IS THE PROPERTY OF MERCURY MARINE.
This document is provided for the sole and exclusive use of the original recipient as prescribed by Mercury Marine and may not be distributed or copied, digitally or otherwise,
without the prior written consent of Mercury Marine.
Page 2 / 4
© 2004 Mercury Marine
SEPTEMBER 2004
2004-06R
Gen III Cool Fuel Module Diagnostics
9. Remove the used water separating fuel filter element from the filter cup, place it in a
clean, approved container.
10. Dispose of any water or debris that may be in the filter cup.
11. Install a new water separating fuel filter element into the filter cup. Push the element
into the cup until completely seated.
12. Install new O-ring on the filter cup.
13. Attach the filter cap to the filter cup by grasping the filter cap and rotating it in a counter
clockwise direction while holding the filter cup stationary, until the filter cap locks
securely into place.
14. Install the fuel filter assembly slowly into the Cool Fuel Module to prevent spilling fuel,
and align the screws retained in the filter cap with the screw holes in the Cool Fuel
Module. Tighten the filter assembly retaining screws until hand tight.
15. Ensure that the filter cap is firmly seated against the Cool Fuel Module and torque each
filter assembly retaining screw.
Description
Filter assembly retaining screw
Nm
lb. in.
6
53
lb. ft.
16. Reconnect the Cool Fuel Module harness to the engine wiring harness.
17. Supply cooling water to the engine.
18. Properly ventilate the engine compartment.
! WARNING
Avoid serious injury or death due to FIRE or EXPLOSION. Ensure that the engine
compartment is well ventilated and that no gasoline vapors are present to prevent the
possibility of a FIRE or EXPLOSION.
! WARNING
Ensure that no fuel leaks exist before closing the engine hatch.
19. Start the engine. Check for gasoline leaks around the fuel filter assembly. If leaks exist,
stop the engine immediately. Recheck the filter installation, clean spilled fuel and
properly ventilate the engine compartment. Correct the leak.
Electrical
1. Disconnect the electrical connector at the Cool Fuel Module.
2. Connect a Digital Volt / Ohm Meter (DVOM) to the engine side of the electrical
connector.
3. Turn the ignition switch to the run position.
4. Verify that there is 12 volt battery (+) power going to the Cool Fuel Module. If voltage
is less than 11.5 vdc, find and correct the voltage drop or no voltage condition.
NOTE: The fuel pump relay will only remain active for 2-3 seconds while the key is in the
RUN position.
THE INFORMATION IN THIS DOCUMENT IS CONFIDENTIAL AND PROTECTED BY COPYRIGHT AND IS THE PROPERTY OF MERCURY MARINE.
This document is provided for the sole and exclusive use of the original recipient as prescribed by Mercury Marine and may not be distributed or copied, digitally or otherwise,
without the prior written consent of Mercury Marine.
2004-06R SEPTEMBER 2004
© 2004 Mercury Marine
Page 3 / 4
Gen III Cool Fuel Module Diagnostics
Checking Fuel Pressure
1. Connect a fuel pressure gauge to the shrader valve on the fuel rail.
2. Cycle key switch 2-3 times (OFF to RUN position) at 3 second intervals to reach
maximum pressure.
3. Verify that the pressure is within specification.
4. If pressure exceeds 44 psi (303 kPa):
a. Replace the Cool Fuel Module.
5. If pressure is equal to or less than 40 psi (276 kPa):
a. Use a tee fitting and connect a vacuum gauge to the fuel inlet side of the Cool
Fuel Module. Do not remove the fuel inlet fitting adapter.
b. Relieve the fuel pressure in the fuel rail. Refer to section 2A for fuel pressure relief
procedure.
c. Cycle the key switch 2-3 times (OFF to RUN position) at 3 second intervals to
reach maximum pressure.
d. Verify that the vacuum from the fuel source is within specification. If the vacuum
exceeds 2 in. Hg (7 kPa) , excessive fuel restriction exists. Correct the fuel
restriction before proceeding.
e. With the vessel secured to the dock and the engine running in neutral, restrict the
fuel supply and verify that the Cool Fuel Module has the ability to cause a vacuum
reading of 11 in. Hg (37 kPa) or greater. If the vacuum reading is less than 11 in.
Hg (37 kPa) with the fuel supply restricted, replace the Cool Fuel Module.
In-Water Test
1. With a vacuum gauge and a fuel pressure gauge in place, operate the boat throughout
the RPM range and record the pressure and vacuum readings.
2. If the fuel the supply vacuum reading is greater than 2 in. Hg (7 kPa) , find and correct
the fuel supply restriction.
3. If the fuel supply vacuum is within specification and the fuel pressure is less than 40
psi (276 kPa), replace the Cool Fuel Module.
IMPORTANT: It will be necessary to sea-trial the boat following repairs to be sure that the
pressure and the fuel system vacuum remain within specification throughout the RPM
range.
THE INFORMATION IN THIS DOCUMENT IS CONFIDENTIAL AND PROTECTED BY COPYRIGHT AND IS THE PROPERTY OF MERCURY MARINE.
This document is provided for the sole and exclusive use of the original recipient as prescribed by Mercury Marine and may not be distributed or copied, digitally or otherwise,
without the prior written consent of Mercury Marine.
Page 4 / 4
© 2004 Mercury Marine
SEPTEMBER 2004
2004-06R
P/N 91-805747A2 Timing Tool for MerCruiser EFI Engines
a - Timing Tool
b - DLC Connector
71839
CODEMATETM
Marine EFI Code Reader (Rinda)
CodeMate serves as both an EFI problem indicator and a spark timing service tool. The device connects to the DLC in a matter of seconds and alerts the boat owner or technician when
EFI problems are detected. CodeMate allows diagnostic trouble codes (DTC’s) to be read
and when used with a timing light, allows the technician to verify/set the base ignition timing.
Available from:
Rinda Technologies, Inc. Chicago, IL
Telephone: (773) 736-6633
Fax: (773) 736-2950
Rinda #94008
Scan Tools
Older Software and Newer EFI Systems
Older scan tool software for the Quicksilver Digital Diagnostic Terminal (DDT) and
MerCruiser/Rinda scan tools will not be able to read the information coming from either the
newer MEFI’s or the ECM/PCM 555 ECM’s. If you use the wrong software you will get an
“error” message on the display of the DDT scan tool, or you will get incorrect information from
a MerCruiser/Rinda scan tool.
Quicksilver DDT Scan Tool (New Cartridge)
The DDT will need MerCruiser cartridge, version 2.0 (P/N 91-803999), to read MEFI-3 ECM’s.
This cartridge can also read data from Thunderbolt 5 ignition used on carbureted models. See
Service Bulletin 2001-2. A second cartridge will be required to read ECM/PCM 555 controllers. Order SmartCraft DDT cartridge, version 1.31 (P/N 91-880118A04).
2-18 - TOOLS & TECH TIPS
MerCruiser EFI III (1004)
Tech Tips
The following “Tech Tips” are ideas that you may find useful.
1. Cylinder Balance Test Tool
Construct eight tools as shown above. Insert a hose end into each spark plug wire tower
on HVS (distributor) cap and insert bullet terminal end into corresponding spark plug wire
boot. Start engine. By grounding each hose in turn with a 12v test light, you will be able
to tell if each cylinder is functioning.
2. Remote Starter Switch, PN 91-52024A1
Probably the easiest way to attach the remote starter switch is to hook one lead to any
convenient power source, such as either side of the circuit breaker or the slave solenoid
red-purple terminal, and the other lead to the slave solenoid small yellow-red terminal.
! CAUTION
DO NOT attach the remote starter switch to both large terminals of the slave solenoid. If this is done, pressing the switch will bypass the slave solenoid and all starting current will flow through the switch and its attaching wires. This can cause
equipment damage and personal injury.
3. When it is necessary to probe circuits, NEVER puncture wiring insulation as this can permit moisture to enter and result in circuit failure due to corrosion. Care should also be exercised when probing terminals in harness blocks. Insertion of a probe that is too large can
spread the terminal, preventing good pin to pin contact when the harness block is reconnected. Use of the GM style test leads, PN J-35616-A, and/or the Rinda EFI test lead set,
PN 94025, can prevent both these problems.
4. When an engine won’t start or starts but runs poorly, be sure to not forget to check for
water in the fuel and for old, deteriorated fuel. If either of these conditions is suspected,
use of a portable outboard tank can be very helpful.
5. The PG (Permanent magnet, Gear reduction) starters used on all current sterndrive engines are highly efficient. Because of this, a battery that is too weak to provide sufficient
voltage at the ECM/PCM to start an engine can, at times, turn it over so fast that the battery
is not immediately suspected. Don’t forget to check battery voltage when troubleshooting
a “hard start” complaint.
6. The crank position sensor (CPS), fuel pump and injectors on ECM 555 equipped engines
can be easily checked. Remove the CPS from the engine. With the harness attached to
the CPS and with the ignition switch on, rapidly pass the flat side of a screwdriver blade
close to the sensor tip. A scan tool will show RPM, the injectors will fire and the fuel pump
will run if the sensor is functioning.
MerCruiser EFI III (1004)
TOOLS & TECH TIPS - 2-19
b
6HUYLFH%XOOHWLQ
:DUUDQW\,QIRUPDWLRQ
6HUYLFH,QIRUPDWLRQ
%XOOHWLQ1Rb
3DUWV,QIRUPDWLRQ
&LUFXODWHWR
6DOHV0DQDJHU
$FFRXQWLQJ
6HUYLFH0DQDJHU
7HFKQLFLDQ
3DUWV0DQDJHU
6HUYLFH5HSDLURI(OHFWULFDO7HVW(TXLSPHQW
1RWLFH
7KLVEXOOHWLQUHSODFHV0HU&UXLVHU6HUYLFH%XOOHWLQ
7HVW(TXLSPHQW
$OOHOHFWULFDOWHVWHTXLSPHQWPXVWEHUHWXUQHGWRWKHYHQGRURUUHSDLUIDFLOLW\IRUVHUYLFH
UHSDLUDQGRUUHSODFHPHQWSDUWV$Q\HOHFWULFDOWHVWHTXLSPHQWUHFHLYHGLQ)RQGGX/DF
VKDOOEHUHWXUQHGWRWKHVHQGHU:HHQFRXUDJHFRQWDFWZLWKWKHEXVLQHVVSULRUWRVKLSSLQJ
WKH XQLW WR REWDLQ VKLSSLQJ HVWLPDWH DQG UHSDLU GHWDLOV 7KH DGGUHVVHV DQG SKRQH
QXPEHUVDUHIROORZLQJ
9HQGRU
(OHFWURQLF6SHFLDOWLHV,QF
3LHUFH'ULYH
6SULQJ*URYH,/
)D[b
(TXLSPHQW
3DUW1XPEHU
7LPLQJ/LJKWVHOIFRQWDLQHG
0XOWL0HWHU'9$
0HUFWDFK'LJLWDO7DFKRPHWHU
$
(),7HVWHU
$
127( 'LJLWDO 9ROW 0HWHU LV QRW VHUYLFHDEOH 3XUFKDVH D JRRG TXDOLW\ PHJ RKPV
LPSHGDQFH1RWXVLQJPHJRKPVLPSHGDQFHPD\QRWDOORZ(),WHVWHUWRQRUPDOL]H
9HQGRU
(TXLSPHQW
0HUF27URQLF6HUYLFH'HSDUWPHQW
%UDQFK
32%R[
$OPRQW0,
)D[b
3DUW1XPEHU
7DFK'ZHOO0HWHU
,JQLWLRQ$QDO\]HU
7+(,1)250$7,21,17+,6'2&80(17,6&21),'(17,$/$1'3527(&7('%<&23<5,*+7$1',67+(3523(57<2)0(5&85<0$5,1(
7KLVGRFXPHQWLVSURYLGHGIRUWKHVROHDQGH[FOXVLYHXVHRIWKHRULJLQDOUHFLSLHQWDVSUHVFULEHGE\0HUFXU\0DULQHDQGPD\QRWEHGLVWULEXWHGRUFRSLHGGLJLWDOO\RU
RWKHUZLVHZLWKRXWWKHSULRUZULWWHQFRQVHQWRI0HUFXU\0DULQH
5b'(&(0%(5b
k0HUFXU\0DULQH
3DJHb
b
6(59,&(5(3$,52)(/(&75,&$/7(67(48,30(17
9HQGRU
(TXLSPHQW
1RWDYDLODEOH
5HSODFHPHQWSDUWVDUHQRWDYDLODEOH
3DUW1XPEHU
7KXQGHUEROW,JQLWLRQ$QDO\]HU
$
92$0HWHU
0DUN7HVWHU
9HQGRU
63;&RUSRUDWLRQ
3DUN'ULYH
2ZDWRQQD01
,QWHUQDWLRQDO
$
(TXLSPHQW
3DUW1XPEHU
'LJLWDO'LDJQRVWLF7HVWHU''7
$
127($Q\HOHFWULFDOWHVWHTXLSPHQWUHFHLYHGLQ)RQGGX/DFVKDOOEHUHWXUQHGWRWKH
VHQGHU
9HQGRU
(TXLSPHQW
3DUW1XPEHU
%OXH3RLQW3URGXFWV
'07'LJLWDO7DFKRPHWHU0XOWLPHWHU 6:$OOHQ%OYG6WH '07$'LJLWDO7DFKRPHWHU
%HDYHUWRQ25
0XOWLPHWHU
127( 3OHDVH FDOO DQG PDNH UHSDLU DUUDQJHPHQWV SULRU WR VHQGLQJ PHWHU %OXH3RLQW
7HFKQLFDODQG&XVWRPHU6HUYLFHRIILFHKRXUV$0303DFLILF7LPH=RQH
7+(,1)250$7,21,17+,6'2&80(17,6&21),'(17,$/$1'3527(&7('%<&23<5,*+7$1',67+(3523(57<2)0(5&85<0$5,1(
7KLVGRFXPHQWLVSURYLGHGIRUWKHVROHDQGH[FOXVLYHXVHRIWKHRULJLQDOUHFLSLHQWDVSUHVFULEHGE\0HUFXU\0DULQHDQGPD\QRWEHGLVWULEXWHGRUFRSLHGGLJLWDOO\RU
RWKHUZLVHZLWKRXWWKHSULRUZULWWHQFRQVHQWRI0HUFXU\0DULQH
3DJHb
k0HUFXU\0DULQH
'(&(0%(5bb
5
DIAGNOSTICS
3
MerCruiser EFI III (1004)
Table of Contents
Page
Testing Fuel System Pressure on EFI
Throttle Body Injection Systems . . . . . . . . .
Fuel Pressure Test Gauge Adaptor
Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing Mechanical, or Electric Fuel
Supply Pump (used on VST models) . . . .
Precautions . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body Injection With Vapor
Separator Tank (VST) . . . . . . . . . . . . . .
Testing Fuel System Pressure on EFI
Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing Boost Pump (If so equipped) . . . . . .
Precautions . . . . . . . . . . . . . . . . . . . . . . . .
Checking for Restrictions/Vapor Lock
Problems in Fuel Delivery Systems . . . . . .
Delco EST Ignition Troubleshooting . . . . . . .
Erratic Spark Symptoms . . . . . . . . . . . . .
No Spark Troubleshooting . . . . . . . . . . . .
Non-Scan Diagnosis of Driveability
Concerns (With No Codes Set) . . . . . . . . .
“Out-of-Range” Sensors . . . . . . . . . . . . . . . . . .
3-i - DIAGNOSTICS
3-1
3-1
3-2
3-2
3-3
3-4
3-4
3-4
3-6
3-8
3-8
3-8
3-10
3-11
Page
Scan Tool Use With Intermittents . . . . . . 3-11
Quicksilver Digital Diagnostic Terminal
Data Screen Information – MEFI ECM’s . . 3-12
MEFI Data Log Sheet (DDT) . . . . . . . . . . . . . . 3-13
PCM 555/03 and ECM 555
Data Log Sheet (DDT) . . . . . . . . . . . . . . . . . 3-14
MC/Rinda MEFI Data Sheet . . . . . . . . . . . . . . 3-15
PCM/ECM 555 Data Log Sheet
(Rinda Scan Tool) . . . . . . . . . . . . . . . . . . . . . 3-16
Mercury Marine Computer Diagnostic
System (CDS) Data List . . . . . . . . . . . . . . . . 3-17
General Service Precautions When
Working On EFI Systems . . . . . . . . . . . . .
Intermittent Faults . . . . . . . . . . . . . . . . . . . . .
EFI Troubleshooting Guide – MEFI Systems .
PCM/ECM 555 Diagnostics . . . . . . . . . . . . . . .
ECM 555 Troubleshooting Preliminary
Checks . . . . . . . . . . . . . . . . . . . . . . . . . .
MerCruiser Fault Data Lists and
MEFI/ECM/PCM Pin Locations . . . . . . . .
3-19
3-21
3-22
3-26
3-31
3-35
MerCruiser EFI III (1004)
Testing Fuel System Pressure on EFI Throttle Body Injection
Systems
91-881833A2
91-806901
a
a - Remove Fuel Line from Throttle Body Unit and Install Fuel Fitting Connector P/N
91-806901. Connect Fuel Pressure Gauge Kit, P/N 91-881833A2 (S.S. from
91-16850A7), to test system pressure.
Fuel Pressure Test Gauge Adaptor Fittings
The following information is contained in revised Service Bulletin 97-24.
1998-2000 MCM/MIE 7.4L MPI (L29) uses a different size and type of ‘test port’ valve on it
for checking the fuel pressure at the fuel rail. The older Fuel Pressure Gauge Kit (P/N
91-16850A 2) will not attach to this valve. A new kit has superseded this kit and it contains
2 fittings so it will fit both types of ‘test ports’ and a TBI pressure valve to allow the gauge to
connect to TBI engines.
Quicksilver will also sell an Adapter Kit that can be purchased to update the older
91-16850A 1, 2, 3 kit. This kit comes with both size ‘test port’ valve adapters and instructions
on how to fit it to the older gauge kit.
91-881833A 2
Fuel Pressure Gauge Kit.
Kit contains Adapter Kit
and TBI Pressure Valve.
To update older 91-16850A 1, A 2, or A 3
Fuel Pressure Gauge Kits, order the following:
91-806901
91-803135
MerCruiser EFI III (1004)
TBI Pressure Valve.
Allows older Gauge Kits to
connect to TBI engines.
Adapter Kit. Allows older
Gauge Kits to connect to
either type of ‘test port’
valve.
DIAGNOSTICS - 3-1
Testing Mechanical, or Electric Fuel Supply Pump
(used on VST models)
Precautions
WARNING
Always disconnect battery cables from battery BEFORE working on fuel system to
prevent fire or explosion.
WARNING
Be careful when changing fuel system components; gasoline is extremely flammable and highly explosive under certain conditions. Be sure that ignition key is OFF.
DO NOT smoke or allow sources of spark or flame in the area while changing fuel filters. Wipe up any spilled fuel immediately.
WARNING
Make sure that no fuel leaks exist before closing engine hatch.
CAUTION
DO NOT operate engine without cooling water being supplied to seawater pickup
pump, or pump impeller will be damaged and subsequent overheating damage may
result.
NOTICE
BEFORE proceeding, refer to “Precautions”.
1. Disconnect battery cables from battery.
2. Remove fuel line from outlet side of mechanical, or electric fuel supply pump, or from inlet
side of VST tank.
3. Install Fuel Pressure Connector (91-18078) to fuel supply pump, or VST tank and reinstall
fuel line. Tighten connector and fuel line securely.
4. Connect fuel pressure test gauge (0-15 psi) to connector.
5. Reconnect battery cables, start engine, and run at 1800 RPM. If engine will not start, crank
engine to obtain reading.
6. Fuel pressure should be within specifications (7-9 psi). If not, replace fuel pump.
Fuel Fitting Connector
91-18078
Description: Connects fuel pressure gauge
to fuel system, installed between fuel supply
pump and VST unit.
73469
3-2 - DIAGNOSTICS
MerCruiser EFI III (1004)
Testing Mechanical, or Electric Fuel Supply Pump
(used on VST models) (cont.)
Throttle Body Injection With Vapor Separator Tank (VST)
e
f
g
d
Attach Fuel Fitting Connector
at Either Location
b
c
a
a
b
c
d
e
f
g
- Fuel line from boat’s fuel tank
- Water separating fuel filter
- Supply pump (mechanical or electric)
- Vapor separator tank
- Throttle body with 2 fuel injectors
- Fuel pressure regulator
- Return line to vapor separator tank
MerCruiser EFI III (1004)
73895R1
DIAGNOSTICS - 3-3
Testing Fuel System Pressure on EFI Systems
d
a
b
c
a
b
c
d
76681
- Fuel Rail Assembly
- Intake Manifold
- Throttle Body
- Fuel Pressure Test Port
Testing Boost Pump (If so equipped)
Precautions
WARNING
Always disconnect battery cables from battery BEFORE working on fuel system to
prevent fire or explosion.
WARNING
Be careful when changing fuel system components; gasoline is extremely flammable and highly explosive under certain conditions. Be sure that ignition key is OFF.
DO NOT smoke or allow sources of spark or flame in the area while changing fuel filters. Wipe up any spilled fuel immediately.
WARNING
Make sure that no fuel leaks exist before closing engine hatch.
CAUTION
DO NOT operate engine without cooling water being supplied to seawater pickup
pump, or pump impeller will be damaged and subsequent overheating damage may
result.
NOTICE
BEFORE proceeding, refer to “Precautions”.
1. Disconnect battery cables from battery.
2. Remove fuel line from outlet side of boost pump, or from inlet side of water separating fuel
filter.
3. Install Fuel Pressure Connector (91-18078) to boost pump, or water separating fuel filter
and reinstall fuel line. Tighten connector and fuel line securely.
3-4 - DIAGNOSTICS
MerCruiser EFI III (1004)
4. Connect fuel pressure test gauge (0-15 psi) to connector.
5. Reconnect battery cables, start engine, and run at 1800 RPM. If engine will not start, crank
engine to obtain reading.
6. Fuel pressure should be within specifications (7-9 psi). If not, replace fuel pump.
NOTE: If the screen on the inlet side of the boost pump is clogged, the boost pump pressure
will be low.
d
b
a
77645
e
c
a
b
c
d
e
- Fuel from Tank
- Fuel Boost Pump
- Water Separating Fuel Filter
- Fuel Cooler
- Install Fuel Fitting Connector (91-18078) at Either Location
Fuel Fitting Connector
91-18078
Description: Connects fuel pressure gauge
to fuel system, installed between fuel supply
pump and VST unit.
73469
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-5
Checking for Restrictions/Vapor Lock Problems in Fuel
Delivery Systems
If there are any restrictions in the fuel delivery system the engine may experience vapor lock
and other driveability problems. Fuel supply problems can be checked by using a vacuum
gauge on a water separating fuel filter fitting port. Installing it on the inlet side will check the
fuel tank to filter supply line and hardware (anti-siphon valve, fuel fittings, etc.). Installing it
on the outlet side will check the supply line, hardware and the filter. If the outlet vacuum reading is higher than the inlet reading, the filter is clogged. If both readings are high then inspect
the fuel tank, supply line and hardware. Check for trash in the tank (blocking the pick-up),
clogged fuel filter screens on the end of pick-up tubes in the tank, clogged in-line fuel filters,
blocked off fuel tank vent, bent pick-up tube, dirt and debris in fuel fittings, wrong size fuel
fittings (undersize connector fittings, undersize fuel shut off valve passages, etc.), undersize
fuel line, or a malfunctioning anti-siphon valve.
Digital Vacuum
Gauge
“T” Fitting
Clear hose
can be used
to check
for air
bubbles
EFI
Fuel System
Fuel Pump
(Mechanical, or Electric,
depending on Fuel System)
Water Separating
Fuel Filter
Fuel Tank
There is a MerCruiser specification for allowable vacuum, when measured at the inlet side
of the engine mounted MerCruiser Water Separating Fuel Filter or if there is none mounted
on the engine, at the inlet side of a fuel pump. Use a digital vacuum gauge (an analog gauge
may not give accurate enough readings at these low levels) that reads in either in. Hg. (inches
of mercury), or kPa (kilopascals).
The specification is: 2 in. Hg. (7 kPa) maximum at: idle, 3000 rpm, full throttle and then
back at idle rpm (check at each point).
Any anti siphon valve or restriction that causes a higher reading can contribute to vapor locking and other driveability problems. In hot weather, if you see 0 vacuum on the gauge and the
engine is still running poorly, check the inlet fuel line to ensure that a good solid flow of fuel
is in the line, instead of a mixture of fuel and vapors. If the vacuum is too high, try a less restrictive anti siphon valve. Restrictive anti siphon valves can cause vapor locking conditions.
Going to the next larger Inside Diameter fuel lines and fittings can help lower the vacuum also.
This larger diameter ID can also help correct vapor locking conditions. An example is shown
below.
5/16 in. (8 mm) Fuel Line ID
5.5 in. Hg or (17.8 kPa)
Too high.
3/8 in. (9.5 mm) Fuel Line ID
2.5 in. Hg or (8.2 kPa)
Too high.
1/2 in. (12.5 mm) Fuel Line ID
0.8 in. Hg or (2.7 kPa)
Good
See MerCruiser Service Bulletin 99-7 (Rev. 1/01) for information on gasoline engine vapor
locking.
3-6 - DIAGNOSTICS
MerCruiser EFI III (1004)
Delco EST Ignition Troubleshooting
Erratic Spark Symptoms
1. If the erratic spark occurs only when the engine is warm, or is especially bad on warm
2.
3.
4.
5.
6.
days, remove the ignition module and make sure that plenty of thermal transfer compound
is present on the module’s base. The module will misfire if it is too hot.
Verify that the purple power lead (carbureted) or red power lead (EFI) to the ignition coil
is holding steady battery voltage during the erratic spark (misfiring) event. If not, check
the key switch and safety lanyard switch for loose connections or internal failure.
a. Try isolating the boat harness with a shop test harness (the 3-foot MerCruiser harness
– part #84-812475A3 and MerCruiser ignition switch assembly – part #54212A7). If
the problem disappears, the problem is in the boat harness, not the MerCruiser engine
harness.
b. There are several splices in the purple lead on almost all MerCruiser engines, so it
may be necessary to go into the engine harness to find the loose connection. On an
EFI engine, ignition coil power comes from the system relay.
If the purple (or red) power lead to the coil holds steady voltage, carefully flex the pink and
brown harness (between the coil and the ignition module) while the engine is running. If
the engine runs better or quits, replace the harness between the coil and ignition module.
This is usually because the filter in the pink lead has failed.
If erratic spark is still present, isolate the gray (carbureted) or white (EFI) tach lead at the
negative side of the ignition coil. Use a suitable jumper lead to jump the purple (or red)
lead to the ignition coil and leave the tach lead disconnected. Kent-Moore Jumper Lead
Kit #J-35616 works well, or you can cut the gray (or white) tach lead near the ignition coil
and install a bullet connector from Quicksilver connector kit part #86-813937A2. If the engine now runs better, tach lead is partially shorted to ground in the engine harness, boat
harness or in the tach itself.
Alpha EFI “MEFI-1” Models – if erratic spark is still present, bypass shift interrupt switch
with the Bravo jumper lead (P/N 805592A1). If the engine now runs better, replace the shift
interrupt switch.
If erratic spark is still present, troubleshoot the secondary system with a Kv meter.
No Spark Troubleshooting
1. Visually check the ignition coil for melted plastic on its outer case. If the case is melted,
the tachometer lead (gray or white) is shorted to ground somewhere. Isolate and repair
before replacing the ignition coil.
2. Make sure that battery voltage is present at the purple power lead (carbureted) or red
power lead (EFI) at the ignition coil. If not, isolate and repair the problem in the engine or
boat harness.
3. Isolate the gray (carbureted) or white (EFI) tach lead at the negative side of the ignition
coil as described in the previous section, step 4. If spark is now present, the tach lead is
shorted to ground in the engine harness, boat harness or in the tach itself.
4. Disconnect the 4 pin connector from the ignition module.
Carbureted models: if spark is now present, the shift cut-out switch is stuck on or shorted
closed. Replace the switch and retest.
EFI models: if spark is now present, the ECM is sending bypass voltage to pin “B” of the
ignition module and it is not supposed to. The EFI system will have to be diagnosed at
this time, as there is not a problem with the EST system.
3-8 - DIAGNOSTICS
MerCruiser EFI III (1004)
5. Disconnect the 2-pin connector from the ignition module. With the Key ON, check for battery voltage at both the pink and brown terminals of the harness.
a. If there is not battery voltage at the pink terminal, replace the 2-wire harness as the
filter is most likely blown open.
b. If there is not battery voltage at the brown terminal, replace the ignition coil as the primary windings have most likely melted open (because of a shorted tach lead).
c. Reconnect the 2-pin connector to the ignition module when finished.
6. If spark is still not present, remove the distributor cap and check the pickup coil for resist-
ance and short-to-grounds. Resistance across the green and white leads must be
500-1500 ohms (750-850 preferred) and the reading must be steady. Resistance between the green lead and the distributor frame must be “infinity” and resistance between
the white lead and the distributor frame must be “infinity”. If any of these readings differ
from specifications, replace the pickup coil.
7. Verify that the timer core is still magnetic. This is the part that rotates above the pickup
coil.
8. If spark is still not present, you will need to “false trigger” the module to determine if it is
opening and closing the primary circuit. Proceed as follows:
a. If still isolated, reconnect the tach lead to the ignition coil. Connect a voltmeter to the
gray tachometer lead bullet connector (near the ignition coil). Set the meter to read
DC volts. Connect an air gap tester from the coil’s secondary terminal to ground.
b. Remove one of the ignition module mounting screws and loosen the other. Rotate the
module out from the distributor frame, then retighten the loose screw. Connect the
positive lead from a 1.5 volt AA (or similar) battery to the ignition module’s “P” terminal
(pickup coil terminal).
c. With the key in the ON position, note the voltmeter reading. It must be battery voltage.
If not, you didn’t verify the coil primary windings are good or you didn’t find the short
to ground in the gray tach lead. If the voltage is OK, proceed.
d. While observing the voltmeter, momentarily connect the negative lead of the 1.5 volt
battery to the distributor frame. The voltage must drop several volts as the module
grounds the negative side of the coil. If not, replace the ignition module.
e. When the negative battery lead is disconnected from the distributor frame, the voltage
must rise back to battery voltage and the ignition coil should fire. If the voltage
changes, but the coil does not fire, replace the ignition coil (the secondary windings
are open or shorted).
f.
MerCruiser EFI III (1004)
When finished, reconnect all leads and connectors.
DIAGNOSTICS - 3-9
Non-Scan Diagnosis of Driveability Concerns
(With No Codes Set)
If a driveability concern still exists after following the diagnostic circuit check and reviewing
“Troubleshooting,” an out-of-range sensor may be suspected. Because of the unique design
of the EFI system, fail-safes have been incorporated into the ECM to replace a sensed value
with a default value in the case of a sensor malfunction or sensor wiring concern. By allowing
this to occur, limited engine performance is restored until the vessel is repaired. A basic understanding of sensor operation is necessary in order to diagnose an out-of-range sensor.
If the sensor is within its working or acceptable parameters, as shown, (Figure A) the ECM
does not detect a problem. If the sensor should happen to fall out of this “window,” a code will
be stored. A known default value will replace the sensed value to restore engine performance.
If the sensor is out of range, but still within the operating window of the ECM, the problem will
go undetected by the ECM and may result in a poor driveability condition.
A good example of this would be if the coolant (ECT) sensor was reading incorrectly and indicating to the ECM that coolant temperature was at 20° F, but actual coolant temperature was
175° F. (Figure B) This would cause the ECM to believe that the engine was running cold. The
ECM would then control the fuel injectors to deliver more fuel than was actually needed and
result in an overly rich, rough running condition. This condition would not have caused a code
to set as the ECM interprets this as within its range.
To identify a sensor which is out of range, unplug it while running the engine. After approximately two minutes, the diagnostic code for that sensor will set a code, and replace the
sensed value with a default value. If at that point a noticeable performance increase is observed, the diagnostic testing code chart for that particular sensor should be followed to correct the problem.
NOTE: Be sure to clear each code after disconnecting and reconnecting each sensor. Failure
to do so may result in a misdiagnosis of the problem.
3-10 - DIAGNOSTICS
MerCruiser EFI III (1004)
“Out-of-Range” Sensors
Scan Tool Use With Intermittents
The scan tool allows manipulation of wiring harnesses or components with the engine not running, while observing the scan tool readout.
The scan tool can be plugged in and observed while running the vessel under the condition
when the Malfunction Indicator Lamp turns ON momentarily or when the engine driveability
is momentarily poor. If the problem seems to be related to certain parameters that can be
checked on the scan tool, they should be checked while running the vessel. If there does not
seem to be any correlation between the problem and any specific circuit, the scan tool can
be checked on each position, watching for a period of time to see if there is any change in
the readings that indicates intermittent operation.
The scan tool is also an easy way to compare the operating parameters of a poorly operating
engine with those of a known good one. For example, a sensor may shift in value but not set
a trouble code. Comparing the senor’s readings with those of the typical scan tool data readings may uncover the problem.
The scan tool has the ability to save time in diagnosis and prevent the replacement of good
parts. The key to using the scan tool successfully for diagnosis lies in the technician’s ability
to understand the system he is trying to diagnose as well as an understanding of the scan
tool operation and limitations. The technician should read the tool manufacturer’s operating
manual to become familiar with the tool’s operation.
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-11
General Service Precautions When Working On EFI Systems
The following requirements must be observed:
1. Before removing any ECM system component, disconnect the negative battery cable.
2. Never start the engine without the battery being solidly connected.
3. Never separate the battery from the on-board electrical system while the engine is
running.
4. Never separate the battery feed wire from the charging system while the engine is
running.
5. When charging the battery, disconnect it from the boat’s electrical system.
6. Ensure that all cable harnesses are connected solidly and that battery connections are
thoroughly clean.
7. Never connect or disconnect the wiring harness at the ECM when the ignition is switched
ON.
8. Before attempting any electric arc welding, disconnect the battery leads and the ECM
connector(s).
9. When steam cleaning engines, do not direct the steam cleaning nozzle at ECM system
components. If this happens, corrosion of the terminals or damage of components can
take place.
10. Use only the test equipment specified in the diagnostic charts, since other test equipment
may either give incorrect results or damage good components.
11. All voltage measurements using a voltmeter require a digital voltmeter with a rating of 10
megohms input impedance.
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-19
12. When a test light is specified, a “low-power” test light must be used. DO NOT use a highwattage test light. While a particular brand of test light is not suggested, a simple test, as
shown below, on any test light will ensure it to be safe for system circuit testing. Connect
an accurate ammeter (such as the high impedance digital multimeter) in series with the
test light being tested, and power the test light ammeter circuit with the vehicle battery.
a
b
a - Test Light
b - Battery
IMPORTANT: If the ammeter indicates LESS than 3/10 amp. current flow (.3 A or 300
mA), the test light is SAFE to use.
If the ammeter indicates MORE than 3/10 amp. current flow (.3 A or 300 mA), the test
light is NOT SAFE to use.
NOTE: Using a test light with 100 mA or less rating may show a faint glow when test actually
states no light.
13. When using a DVOM to perform voltage measurements, turn the ignition OFF when connecting the DVOM to the circuitry to be tested.
3-20 - DIAGNOSTICS
MerCruiser EFI III (1004)
Intermittent Faults
IMPORTANT: Problem may or may not turn “ON” the Malfunction Indicator Lamp (MIL)
or store a DTC. DO NOT use the Diagnostic Trouble Code (DTC) tables for intermittent
problems. The fault must be present to locate the problem.
Most intermittent problems are caused by faulty electrical connections or wiring. Perform
careful visual/physical check. Check for the following conditions:
•
Poor mating of the connector halves, or a terminal not fully seated in the connector body
(backed out or loose).
•
Improperly formed or damaged terminals and/or connectors.
All connector terminals in the problem circuit should be carefully checked for proper contact
tension.
•
Poor terminal to wire connection (crimping).This requires removing the terminal from the
connector body to check. Refer to “Wiring Harness Service” in the “Description and System Operation” section.
The vessel may be driven with a Digital Multimeter connected to a suspected circuit. An
abnormal voltage when malfunction occurs is a good indication that there is a fault in the circuit being monitored.
A scan tool (see “Special Tools” for part numbers) can be used to help detect intermittent
conditions. The scan tools have several features that can be used to locate an intermittent
condition. The following features can be used in finding an intermittent fault:
The “Record” feature or choosing not to erase data can be triggered to capture and store
engine parameters within the scan tool when the malfunction occurs. This stored information
can then be reviewed by the service technician to see what caused the malfunction.
To check loss of DTC memory, disconnect TP sensor and idle engine until the MIL comes
“ON.” A trouble code should be stored and kept in memory when ignition is turned “OFF.” If
not, the ECM is faulty. When this test is completed, make sure that you clear the DTC 22 from
memory.
An intermittent MIL with no stored DTC may be caused by the following:
•
Ignition coil shorted to ground and arcing at ignition wires or plugs.
•
MIL wire to ECM shorted to ground.
•
Poor ECM grounds, Go to ECM wiring diagrams.
•
Check for an electrical system interference caused by a sharp electrical surge. Normally,
the problem will occur when the faulty component is operated.
•
Check for improper installation of electrical options such as lights, ship to shore radios,
sonar, etc.
•
Check that knock sensor wires are routed away from spark plug wires, ignition system
components and charging system components.
•
Check for secondary ignition components shorted to ground, or an open ignition coil
ground (coil mounting brackets).
•
Check for components internally shorted to ground such as starters, alternators or relays.
All Ignition Control (IC) module wiring should kept away from the alternator. Check all wires
from the ECM to the ignition control module for poor connections.
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-21
EFI Troubleshooting Guide - MEFI Systems
Troubleshooting Flow Chart for MerCruiser EFI/MPI Engines (abbreviated)
A Diagnostic Trouble Code indicates that the ECM has sensed that the circuit in question has recorded a sensor value outside of its acceptable “window” for at least as long as its pre-programmed
time period.
I. The process begins with a Customer Complaint or when the technician notes an “Observable
Symptom”.
II. The technician must Verify (or Duplicate) the complaint (or symptom).
III. The technical must perform the OBD (On Board Diagnostic) check, which consists of three major
steps:
A. Verify scan tool link up (communication with ECM) or code 12 on the winky-blinky. If not, go to
the appropriate chart in the service manual (usually Chart A-1 and/or A-2).
B. Verify that the engine will start. If not, go to the “no-start” chart (usually Chart A-3). Note that the
engine does not have to run correctly, it just must run.
C. Check for Diagnostic Trouble Codes. If codes are present, fix active codes first (lowest number
code to highest number code), then repair logged codes in same manner. Locate the code in the
table of contents (of the appropriate service manual and section). The section is usually called
“general system diagnostics” or just “diagnostics”.
1. When troubleshooting active codes, the circuit in question is experiencing a failure right
now. You are looking for an open circuit or short circuit in the 2 or 3 wires involved with the
sensor in question, the sensor itself has actually failed or the connections at the ECM have
failed. In one fashion or another, the troubleshooting chart will have you check each wire for
continuity and shorts and test the sensor for correct operation.
2. When troubleshooting logged codes, the circuit in question is not experiencing a failure at
this time. You are looking for an intermittent connection or an intermittent short circuit that is
not present right now. You must still check circuits for opens and shorts, but you must wiggle
wires and connectors during all tests in attempt to locate the poor connection. Carefully look
for subtle problems, such as corroded connections and internal wiring harness splices; and
for connectors with a loose fit between the male and female pins.
3. Codes rarely indicate a fault with the ECM. Assume that the ECM is working correctly until
complete and thorough troubleshooting procedures prove otherwise.
IV. If no codes are present, but you still have an observable symptom, go to the “diagnosis by symptom”
section, usually called “fuel injection system troubleshooting”. Match the observed symptom with
the closest chart in the table of contents. Carefully follow the troubleshooting chart to test each suspect system or circuit. The problem may be that a sensor is “out of calibration” or it may be that the
problem has nothing to do with the EFI system.
V. If there are no codes and no observable symptoms, then troubleshooting is finished.
3-22 - DIAGNOSTICS
MerCruiser EFI III (1004)
EFI Troubleshooting Guide - MEFI Systems (cont.)
Visual/Physical Check:
I.
Verify that the battery is fully charged and is of sufficient capacity for the engine being tested. If
necessary, substitute a known good battery.
II. Check the battery cable connections. Make sure they are clean and tight. If present, discard wing
nuts and replace with corrosion resistant hex nuts. A corrosion resistant toothed washer should be
installed between the battery terminal and the cable end (stack up must be battery terminal, washer, cable, nut). Make sure the cable connections are tight at the starter solenoid and that the block
fuse on the starter solenoid (if present) is tight and its’ through bolt is not loose. Also make sure the
ground stud is not loose in the engine block and that its’ nut is tight.
III. If there is any doubt about the mechanical condition of the engine, perform a compression test.
IV. Make sure the safety lanyard is correctly installed and that the customer understands the correct
starting procedure (clear flood mode).
V. Check that all grounds are clean and tight. If the negative battery cable is connected to the ground
stud that does not contain all of the EFI and engine wiring harness ground leads, consider moving
the negative battery cable to that ground stud.
VI. Check all vacuum lines for splits, kinks and proper connections. The fuel regulator on MPI models
must be connected to manifold vacuum, while the fuel regulator on TBI models (cool fuel models)
must be vented to atmospheric pressure (usually at the flame arrestor. The PCV valve used on
newer models is a calibrated air leak, if it is missing or the incorrect valve is installed, engine operation will be effected.
VII. Check for any other additional air leaks in the induction system, such as throttle body and intake
manifold gaskets. If the normal IAC counts for the engine are known, then any air leak will result in
a lower IAC count than normal.
VIII. Unplug and inspect the ECM J-1 and J-2 connectors. Make sure there are no ECM pins bent over
and that all of the correct pins are present. Refer to the service manual charts for the pins used and
not used. Look for signs of tampering, corrosion, damage to the pin locking mechanisms, melted
insulation and any other evidence of shorts or other damage.
IX. Unplug and inspect as many of the sensors and actuators as you can reasonably access. Look for
signs of tampering, corrosion, damage to the pin locking mechanisms, melted insulation and any
other evidence of shorts or other damage. Based on the results of this inspection, further inspection of the harness may be necessary. Remember that there are many internal splices in the harness that may be damaged or defective. If there is damage on the external connections, you will
have to inspect several of the internal splices to verify that the damage is not also present at these
locations.
X. Check for adequate secondary spark. If an air gap tester is used, make sure it will not ignite any
fuel vapors that may be present in the bilge. A KV meter can also be used to check for adequate
secondary voltage. Make sure the secondary wires are in good physical shape (correctly routed
and that the boots are not split at either end). Remove the distributor cap and check for signs of
moisture and carbon tracking.
A. If there is no spark and the engine is equipped with Delco EST ignition, unplug the 4-pin connector at the distributor and recheck spark. If spark is still not present, the fault is isolated in
the EST ignition system and is not an EFI system fault. With the 4-pin connector disconnected, this ignition can be diagnosed in the same manner as the 3.0 liter carbureted engine.
B. If there is no spark and the engine is equipped with the Mercury Marine Thunderbolt distributor, refer to Service Bulletin 99-2 for troubleshooting procedures. These engines do not have
a separate ignition module, instead they use the MEFI 3 ECM to control the ignition coil primary circuit.
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-23
EFI Troubleshooting Guide - MEFI Systems (cont.)
XI. Check for adequate fuel pressure at the throttle body or fuel rail.
A. If there is no fuel pressure, check that the fuel pump is actually operating. The pump must run
for at least 2 seconds each time the key is turned to the on position. If the fuel pump and the
warning horn are not operating as the key is turned on, make sure the ECM is powering up
(check the fuses and the system relay).
B. On TBI models, the fuel pressure must be constant at all speeds and must be 30 psi +/– 2psi.
C. On MPI models, the fuel pressure varies with engine vacuum. Fuel pressure will be high during cranking, low at idle and increase proportionally as the throttle is opened to the wide-open
position. Disconnect the vacuum line to find the regulator’s rated pressure, then reconnect
the vacuum line to make sure the pressure drops at idle. Pressure specifications are 30, 36 or
43 psi (+/– 2psi) depending on model and year. Pressure usually drops about 6 psi at idle
(from the regulator’s rated specification). Refer to the service manual for specifications.
D. If fuel pressure drops at higher speed and higher engine loads, check the boat’s fuel system
(the supply system) for restrictions with an accurate vacuum gauge and clear hose at the water separating fuel filter’s inlet. As the engine is run from idle to wide open throttle and back to
idle, the clear hose must not show the presence of any air bubbles and the vacuum gauge
must not read higher than 2 in.-hg. Refer to Service Bulletin 99-7 for additional information.
E. If the supply system tests ok, but the fuel pressure is low at high speeds and loads, replace the
water separating fuel filter and retest. If pressure is still low, most likely the fuel pump is defective.
XII. Unplug and inspect the main harness (10 pin) connector between the engine and boat harnesses.
If there is any doubt about the boat harness, substitute a shop harness and key switch assembly
and rerun the boat. If the problem disappears, the problem is in the boat harness, not the MerCruiser engine harness. A suitable test harness can be assembled from the following components:
A. MerCruiser 3 foot instrument harness cable – part number 84-812475A3
B. MerCruiser ignition switch assembly – part number 54212A7
C. Use suitable machine screws and nuts to join the switch’s ring terminals to the harness’s ring
terminals, then cover the connections with heat shrink tubing.
D. A standard piezo warning horn can also be added to provide audible warning of cooling system overheat, low crankcase oil pressure and low drive oil level (or high transmission temperature).
3-24 - DIAGNOSTICS
MerCruiser EFI III (1004)
EFI Troubleshooting Guide - MEFI Systems (cont.)
Clearing Codes:
Codes are automatically erased after the engine has gone through its preprogrammed number of
“power ups”.
I. Scan tools:
A. The Quicksilver DDT requires that the engine be running in order to clear the codes. If you attempt to clear the codes with the engine not running, the scan tool will attempt to clear the codes,
but fail to actually accomplish it.
B. The Rinda MerCruiser Scan tool can clear the codes with the engine running or with the engine
in the “key-on, engine off” (KOEO) mode.
II. Codemate (winky-blinky):
A. Clearing codes with the winky-blinky requires 2 separate procedures depending on whether you
are working on a MEFI 1 system or a MEFI 2 or 3 system.
1. MEFI 1: It is very difficult to clear codes on a MEFI 1 system because the engine must be
cranked and started during the code clearing process. If the voltage at the ECM drops below
6.9 volts for even the briefest period of time, the ECM will “reset” and “forget” to clear the
codes.
a) Install winky-blinky to the DLC.
b) Key On, Engine-Off (KOEO).
c) Turn the winky-blinky to ON.
d) While in Neutral, cycle the throttle from 0% to 100% and back to 0%.
e) Turn the winky-blinky to OFF for at least 5 seconds.
f) Turn the ignition key to OFF for at least 20 seconds.
g) Start and run the engine for at least 20 seconds.
h) Turn the ignition key to OFF for at least 20 seconds.
i) Verify that the codes were erased.
2. MEFI 2 and 3: Codes can be easily cleared on these models because the engine does not
have to be started.
a) Install winky-blinky to the DLC.
b) Key On, Engine-Off (KOEO).
c) Turn the winky-blinky to ON.
d) While in Neutral, cycle the throttle form 0% to 100% and back to 0%.
e) Turn the ignition key to OFF for at least 5 seconds.
f) Verify that the codes were erased.
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-25
PCM/ECM 555 Diagnostics
A “Fault” indicates that the PCM/ECM555 has either sensed that the circuit in question has recorded a sensor value outside of its acceptable “window” or that a sensor value has gone outside
its “normal” range. For example:
1. A circuit with an open or short would give a fault that is “CKT HI” or “CKT LO”. This means that
the sensor itself has failed with an open or short circuit, or one of the leads between the sensor
and the PCM/ECM is open or shorted. A “CKT HI” fault means that the PCM/ECM is seeing a
5.0 (or nearly 5) volt signal and a “CKT LO” fault means that the PCM/ECM is seeing a 0.0 (or
nearly 0) volt signal.
2. A sensor showing a reading outside of its normal range, but not shorted or open, would give a
fault identifying an abnormal operating condition, such as “ECT Coolant Overheat”, which
means the ECT circuit is operating correctly, but the engine is simply overheating.
Abbreviated Procedure:
I.
The process begins with a Customer Complaint or when the technician notes an “Observable
Symptom”.
II. The technician must Verify (or Duplicate) the complaint (or symptom).
III. The technical should connect a scan tool and check for faults.
A. If the fault is a CKT HI or CKT LO, refer to the wiring diagram and check each of the leads
between the suspect sensor and the PCM/ECM for open and short circuits. The short circuit does not have to be to ground, it could be to any other wire in the harness. If the
leads test good, then the sensor should be replaced.
1. When troubleshooting active faults (faults displayed under the “Fault Status” screen),
the circuit in question is experiencing a failure right now. You are looking for an open
circuit or short circuit in the 2 or 3 wires involved with the sensor in question, the sensor itself has actually failed or the connections at the PCM/ECM have failed.
2. When troubleshooting intermittent faults (faults displayed under the “Fault History”
screens or faults that are NOT active in the “Fault Status” screen), the circuit in
question is not experiencing a failure at this time. You are looking for an intermittent
connection or an intermittent short circuit that is not present right now. You must still
check circuits for opens and shorts, but you must wiggle wires and connectors during
all tests in attempt to locate the poor connection. Carefully look for subtle problems,
such as corroded connections and internal wiring harness splices; and for connectors
with a loose fit between the male and female pins.
a) An excellent way to find an intermittent problem is to use the data monitor function
of the scan tool. While observing the data from the suspect circuit, wiggle the wires
and connectors (of the suspect circuit) while the key is on or while the engine is running. When you locate the bad connection or broken/shorted lead, the data reading
will fluctuate on the scan tool. Keep in mind that the refresh rate of the scan tool is
relatively slow (every 50 milliseconds or so).
b) The record (or min/max) function of the DMT 2000 (or equivalent) multimeter can
also be used to monitor and record the voltage signals on the suspect circuit. Use
the Rinda 94025 Jumper Lead Set (or equivalent) to connect the meter to the
suspect sensor’s signal lead. Sensor signals must never be 0.0 or 5.0 volts. A
multimeter can catch glitches as quick as a micro-second.
3-26 - DIAGNOSTICS
MerCruiser EFI III (1004)
PCM/ECM 555 Diagnostics (continued)
B. If the fault is an abnormal operating condition, repair the system as needed. For example,
if the sea pump pressure is low, check the water pickups for obstructions, then replace the
water pump impeller (and other parts as needed). Abnormal operating condition faults can
be active or intermittent.
C. Faults rarely indicate a defective PCM/ECM. Assume that the PCM/ECM is working correctly until complete and thorough troubleshooting procedures prove otherwise.
IV. If no faults are present, but you still have an observable symptom, then the problem is with a
component or system that the PCM/ECM cannot monitor. Carefully perform the Visual/Physical check (in the following section) and check for obvious things, such as incorrect fuel pressure, engine mechanical problems, exhaust blockage, etc.
A. The problem may be that a sensor is “out of calibration” or it may be that the problem has
nothing to do with the EFI system (clogged fuel supply system, mechanical engine problems, etc.).
B. You can use the scan tool to fire the ignition coil(s) with or without the spark plugs
installed. You can also use the scan tool to drop cylinders (while running) to do “power
balance” tests. On PCM models, each cylinder’s injector can be dropped individually. On
ECM models, each injector “bank” can be dropped individually.
V. If there are no faults and no observable symptoms, then troubleshooting is finished.
Visual/Physical Check:
I.
Verify that the battery is fully charged and is of sufficient capacity for the engine being tested.
If necessary, substitute a known good battery.
II. Check the battery cable connections. Make sure they are clean and tight. If present, discard
wing nuts and replace with corrosion resistant hex nuts. A corrosion resistant toothed washer
should be installed between the battery terminal and the cable end (stack up must be battery
terminal, washer, cable, nut). Make sure the cable connections are tight at the starter solenoid
and that the block fuse on the starter solenoid (if present) is tight and its’ through bolt is not
loose. Also make sure the ground stud is not loose in the engine block and that its’ nut is tight.
III. If there is any doubt about the mechanical condition of the engine, perform a compression test.
IV. Make sure the safety lanyard is correctly installed and that the customer understands the correct starting procedure.
V. Check that all grounds are clean and tight. If the negative battery cable is connected to the
ground stud that does not contain all of the EFI and engine wiring harness ground leads, consider moving the negative battery cable to that ground stud.
VI. Unplug and inspect the main harness (10 pin) connector between the engine and boat harnesses. If there is any doubt about the boat harness, substitute a shop harness and key
switch assembly and rerun the boat. If the problem disappears, the problem is in the boat harness, not the MerCruiser engine harness. A suitable test harness can be assembled from the
following components:
A. MerCruiser 3 foot instrument harness cable – part number 84-812475A3
B. MerCruiser ignition switch assembly – part number 54212A7
C. Use suitable machine screws and nuts to join the switch ring terminals to the harness’s
ring terminals, then cover the connections with heat shrink tubing.
D. A standard piezo warning horn (such as 816492A6) can also be added to provide audible
warning of cooling system overheat, low crankcase oil pressure and low drive oil level (or
high transmission temperature).
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-27
PCM/ECM 555 Diagnostics (continued)
VII. Check for adequate fuel pressure at the fuel rail.
A. If there is no fuel pressure, check that the fuel pump(s) is(are) actually operating. The
pump(s) must run for at least 2 seconds each time the key is turned to the on position. If
the fuel pump(s) and the warning horn are not operating as the key is turned on, make
sure the PCM/ECM is powering up (check the fuses and the wake-up line).
B. On PCM/ECM models, fuel pressure varies with engine vacuum. Fuel pressure will be
high during cranking, low at idle and increase proportionally as the throttle is opened to the
wide-open position. Disconnect the vacuum line (on the cool fuel regulator) to find the
regulator’s rated pressure, then reconnect the vacuum line to make sure the pressure
drops at idle. Pressure specification is 43 psi (+/– 2 psi) on all models. Pressure usually
drops about 6-8 psi at idle (from the regulator’s rated specification).
NOTE: Remember that PCM (and some ECM) models use a boost pump that must maintain
7-9 psi at all speeds and loads. This means that the water separating fuel filter is also
pressurized at 7-9 psi. All Boost pumps must use a “pre-filter”, refer to Service Bulletin
2002-02 and 2002-03 for “pre-filter” information.
C. If fuel pressure drops at higher speed and higher engine loads, check the boat’s fuel
system (the supply system) for restrictions with an accurate vacuum gauge and clear hose
at the water separating fuel filter’s inlet. As the engine is run from idle to wide open
throttle and back to idle, the clear hose must not show the presence of any air bubbles and
the vacuum gauge must not read higher than 2 in.-hg. Refer to Service Bulletin 99-7 for
additional information.
D. If the supply system tests ok, but the fuel pressure is low at high speeds and loads,
replace the water separating fuel filter and retest. If pressure is still low, most likely the
fuel pump is defective
E. All PCM/ECM models use a “dummy” fuel pressure regulator on the fuel rail. This is not
used on marine applications (but is a GM supplied part). The vacuum line attached to the
“dummy” regulator is a possible vacuum leak and a possible fuel leak (if the “dummy”
regulator’s diaphragm should fail). Only the Cool Fuel regulator actually controls fuel rail
pressure.
VIII. Check all vacuum lines for splits, kinks and proper connections. The fuel regulator on all
PCM/ECM models must be connected to manifold vacuum. The PCV valve is a calibrated air
leak, if it is missing or the incorrect valve is installed, engine operation will be effected.
IX. Check for any other additional air leaks in the induction system, such as throttle body and
intake manifold gaskets. If the normal IAC % for the engine are known, then any air leak will
result in a lower IAC % than normal.
X. Unplug and inspect the PCM/ECM A, B and C connectors. Make sure there are no PCM/
ECM pins bent over and that all of the correct pins are present. Refer to the service manual
charts for the pins used and not used. Look for signs of tampering, corrosion, damage to the
pin locking mechanisms, melted insulation and any other evidence of shorts or other damage.
XI. Unplug and inspect as many of the sensors and actuators as you can reasonably access.
Look for signs of tampering, corrosion, damage to the pin locking mechanisms, melted
insulation and any other evidence of shorts or other damage. Based on the results of this
inspection, further inspection of the harness may be necessary. Remember that there are
many internal splices in the harness that may be damaged or defective. If there is damage on
the external connections, you will have to inspect several of the internal splices to verify that
the damage is not also present at these locations.
3-28 - DIAGNOSTICS
MerCruiser EFI III (1004)
PCM/ECM 555 Diagnostics (continued)
XII. Check for adequate secondary spark. If an air gap tester is used, make sure it will not ignite
any fuel vapors that may be present in the bilge. A KV meter can also be used to check for
adequate secondary voltage. Make sure the secondary wires are in good physical shape (correctly routed and that the boots are not split at either end). Remove the distributor cap (ECM
models) and check for signs of moisture and carbon tracking.
Clearing Codes:
Faults are cleared with a scan tool only. Refer to the appropriate DDT flow chart in the PCM/ECM
Technician Guide for appropriate menus.
IMPORTANT NOTES:
1. When firing the ignition coil(s) under the “Auto Self Test” and “Output Load Test” screens:
A. You must specify if the spark plugs are installed or not. If the spark plugs are installed, the
PCM/ECM will fire the coil(s) at the minimum dwell time to prevent it from actually sparking
in the combustion chamber (possibly igniting fuel vapors). If the spark plugs are not
installed, the PCM/ECM will fire the coil(s) at the maximum dwell time to allow for visible
spark. In either case, the PCM/ECM will monitor the 5 volt trigger circuits to attempt to
detect whether the coil has “fired”.
NOTE: If using an air gap tester (instead of a resistor-type spark plug), it may cause RFI
that can result in the warning horn chirping or other unusual symptoms to occur. DO NOT
allow open spark to occur if fuel vapors might be present.
B. A PCM can individually fire each coil. An ECM only has one coil, so no matter what
“cylinder” you attempt to activate, the same coil will fire in each case. However, the spark
will attempt to go to wherever the rotor (in the distributor) is pointing. You must test at the
coil lead or know where the rotor is pointing and install the test spark plug in that cylinders
lead.
2. When performing the “Cylinder Misfire Test”, the PCM/ECM will add extra fuel through the fuel
injectors at idle and off-idle speeds, but will turn off the fuel injector(s) at higher speeds. The
test is best performed under high-load/high-speed conditions. A PCM can individually control
each fuel injector. An ECM engine fires the fuel injectors in banks. Bank #1 is 1,3 & 5 on a V6
and 1,4,6 & 7 on a V8. Bank #2 is 2, 4 & 6 on a V6 and 2,3,5 & 8 on a V8. Pressing number 1
activates “bank 1”, while pressing number 2 activates “bank 2”. Pressing any other number will
result in an error message.
3. When firing the fuel injectors under the “Auto Self Test” and “Output Load Test” screens, the
same rules apply as above. PMC fires individual injectors, ECM fires banks.
4. Timing is not adjustable on any PCM/ECM engine. The distributor on ECM engines only
decides “where” the spark goes, not “when” it goes. Rotating the distributor from its properly
“indexed” position will cause the spark to jump to the wrong tower in the distributor cap.
5. IMPORTANT: On ECM555 engines, when the crankshaft is EXACTLY at #1 TDC
compression, the distributor’s rotor must EXACTLY align with the #6 (V6 engines) or #8
(V8 engines) cast into the distributor housing. If not, the spark will jump to the wrong
“tower” in the distributor cap.
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-29
PCM/ECM 555 Diagnostics (continued)
DTS Faults:
Faults relating to the ERC (electronic remote control) are only displayed on the System View
(SC5000). There are 3 potentiometers in an ERC, 1 for shift control and 2 for throttle control, as
well as switches for trim control, system view cursor control and other features.
Faults relating to the ETC (electronic throttle control) and the ESC (electronic shift control) are
displayed on the DDT and the System View.
Two TPS sensors are integrated into the ETC. The ETC is replaced as an assembly and is not
serviceable. There are 6 wires on an ETC. Sensor Power, Sensor Ground, TP1 signal, TP2 signal
and 2 wires to run the servo motor.
The ESC contains one integrated sensor (like a TPS). The ESC is replaced as an assembly and is
not serviceable. There are 5 wires on an ESC. Sensor Power, Sensor Ground, Sensor Signal and
2 wires to run the servo motor. A separate 2-wire Neutral Switch is used to cross-check the
integrated sensor. The switch is located on the shift bracket (Bravo models) and is the
Transmission’s Neutral Safety switch on Inboard models.
DTS engines use a different PCM555 controller with a Motorola Base Part Number of 859611.
Wiring diagrams are not in print at this time. Refer to the PCM/ECM spreadsheet showing the
location, function and color-code of each PCM/ECM pin.
3-30 - DIAGNOSTICS
MerCruiser EFI III (1004)
ECM 555 Troubleshooting Preliminary Checks
Several of the diagnostic procedures call for the completion of a Visual / Physical Checklist.
The importance of this step cannot be stressed too strongly. It can lead to correcting a
problem without further checks and can save valuable time. This check is outlined below:
Visual / Physical Checklist
Step
1.
Action
Is the battery fully charged?
Yes
No
Go to Step 2.
Recharge or
replace battery.
Restart
checklist.
Go to Step 3.
Clean or
tighten battery
cable
connections.
Go to Step 3.
2.
Are the battery cable connections clean
and tight?
3.
Are the external engine grounds tight and
clean?
Go to Step 4.
Clean or
tighten engine
grounds.
Go to Step 4.
4.
Check fuel line and fuel line connections for
leaks, corrosion and blockage.
Was a problem found?
Repair
problem.
Go to Step 5.
Go to Step 5.
5.
Check the 3 fuses located next to the ECM
on the engine.
Are the fuses good?
Go to Step 6.
Replace fuse.
Go to Step 6.
6.
Check the 50 amp circuit breaker located on
the engine to ensure that the circuit is
closed.
Was the circuit breaker tripped?
Reset the
circuit breaker.
Go to Step 7.
Go to Step 7.
7.
Is the Lanyard Stop Switch in the wrong
position?
Toggle switch.
Go to Step 8.
Go to Step 8.
Go to OBD
System Chart.
Obtain
appropriate
version of
software.
Go to OBD
System Chart.
8.
MerCruiser EFI III (1004)
Are you using the correct version of scan
tool software for the engine in question?
DIAGNOSTICS - 3-31
ECM 555 On-Board Diagnostic (OBD) System Chart
Step
3-32 - DIAGNOSTICS
Action
Yes
No
1.
Was the Visual / Physical Checklist
completed?
Go to Step 2.
Go to Visual /
Physical
Checklist.
2.
Connect scan tool to the engine.
Ignition ON.
Is the scan tool communicating with the
ECM?
Go to Step 10.
Go to Step 3.
3.
Ignition ON.
Check for battery voltage (B+) at Pin 5 of the
10-pin connector coming from the helm.
Ignition OFF.
With the ignition ON, was B+ present?
Go to Step 4.
Locate and
repair problem
from the
keyswitch to
the engine ten
pin connector.
Re-test system.
4.
Ignition ON.
Check for B+ at ECM Connector B-18.
Ignition OFF.
With the ignition ON, was B+ present?
Go to Step 6.
Go to Step 5.
5.
Check for continuity between Pin 5 of the
10-pin Connector of the engine harness and
ECM Connector B-18.
Was continuity present?
Go to Step 6.
Locate and
repair the open
in the harness.
Re-test system.
MerCruiser EFI III (1004)
ECM 555 On-Board Diagnostic (OBD) System Chart (continued)
6.
Ignition ON.
Check for B+ at Diagnostic connector Pin D.
Ignition OFF.
With the ignition ON, was B+ present?
7.
Check continuity of the ground wire,
Diagnostic connector Pin A and Pin 1 of the
10-pin Connector.
Was continuity present?
Go to Step 7.
Repair or
replace
harness.
Re-test system.
Go to Step 8.
Locate and
repair the open
in the harness.
Re-test system.
8.
Check continuity between Diagnostic
connector Pin B and ECM connector A-12.
Was continuity present?
Go to Step 9.
Locate and
repair the open
in the harness.
Re-test system.
9.
Check continuity between Diagnostic
connector Pin C and ECM connector A-5.
Was continuity present?
Locate and
repair the open
Replace ECM. in the harness.
Re-test system.
10.
Using the scan tool, check for faults stored
in the ECM.
Were any faults present?
Inspect and
Go to
repair fault.
appropriate
Re-test system. symptom chart.
MerCruiser EFI III (1004)
DIAGNOSTICS - 3-33
Fault Data Lists
and
MEFI / ECM / PCM Pin Locations
10/20/2004
Index to Fault Data Lists and MEFI / ECM / PCM Pin Locations
Fault Data Lists
•
•
•
•
MEFI 1, 2 and 3 Faults (“Codes”)
ECM 555/ PCM 555/ PCM 03 Faults
DTS Command Module Faults
DTS Command Module “City ID’s”
Controller Pin Locations
•
•
•
•
•
•
•
•
•
MEFI 1, 2 and 3
ECM 555
PCM 555 and PCM 03
DTS Command Module (and CAN Circuit)
ETC (Electronic Throttle Control), ESC (Electronic Shift Control)
System View
MC Thunderbolt V
MC High-Performance HP525EFI PCM
MC High-Performance HP1075SCi PCM
MEFI 1, 2 and 3 Fault Lists
MEFI 1 Fault List (not all faults are used on each engine)
Fault #
14
21
23
33
42
43
51
CDS Fault Description
ECT Circuit High or Low
TPS Circuit High or Low
IAT Circuit High or Low
MAP Circuit High or Low
IC or Bypass Circuit
Knock Circuit
Calibration Checksum Error
MEFI 2 Fault List
Fault #
14
15
21
22
23
24
25
33
34
41
42
43
44
51
52
CDS Fault Description
ECT Circuit High (open)
ECT Circuit Low (shorted)
TPS Circuit High
TPS Circuit Low
IAT Circuit High (open)
Reserved
IAT Circuit Low (shorted)
MAP Circuit High
MAP Circuit Low
Open IC Circuit
Shorted IC Circuit or Bypass Open/Shorted
Continuous Knock Detected
Knock Sensor Inactive
Calibration Checksum Error
EEPROM failure
MEFI 3 Fault List (not all faults are used on each engine)
Fault #
14
15
21
22
23
24
25
31
32
33
34
41
42
43
44
45
51
52
54
55
61
62
CDS Fault Description
ECT Circuit High (open)
ECT Circuit Low (shorted)
TPS Circuit High
TPS Circuit Low
IAT Circuit High (open)
Reserved
IAT Circuit Low (shorted)
Reserved
Reserved
MAP Circuit High
MAP Circuit Low
Open IC Circuit
Shorted IC Circuit or Bypass Open/Shorted
Continuous Knock Detected
Knock Sensor Inactive
Ignition Coil Driver Circuit Fault
Calibration Checksum Error
EEPROM failure
Reserved
Reserved
Fuel Pressure Sensor Circuit High (high volts)
Fuel Pressure Sensor Circuit Low (low volts)
09-08-04
CDS – ECM 555/ PCM 555/ PCM 03 Master Fault List
NOTE: All faults are not used on each engine
MerCruiser Fault #
1
2
3
4
5
6
7
8
9
10
11
12
13 and 14
15
16
17
18
19
20
21
22
23 – 35
36
37
38
39
40
41 and 42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
MerCruiser Fault Description
Battery Voltage High
Battery Voltage Low
Sea Pump Pressure is Low
Not used by MerCruiser
ETC Loss of Control
ETC Sticking
Fuel Pressure Sensor Circuit High
Fuel Pressure Sensor Circuit Low
Guardian Strategy
Knock Sensor 1
Knock Sensor 2
Oil Pressure is Low
Not used by MerCruiser
MAP Sensor Circuit High
MAP Sensor Circuit Low
MAP Sensor Idle Fault
Not used by MerCruiser
Overspeed
Not used by MerCruiser
ECT Overheat
Warning Horn Output
Not used by MerCruiser
Sea Pump Pressure Circuit High
Sea Pump Pressure Circuit Low
Not used by MerCruiser
Manifold Air Temp Circuit High
Manifold Air Temp Circuit Low
Not used by MerCruiser
EST 1 Open Circuit
EST 1 Shorted Circuit
EST 2 Open Circuit
EST 2 Shorted Circuit
EST 3 Open Circuit
EST 3 Shorted Circuit
EST 4 Open Circuit
EST 4 Shorted Circuit
EST 5 Open Circuit
EST 5 Shorted Circuit
EST 6 Open Circuit
EST 6 Shorted Circuit
EST 7 Open Circuit
EST 7 Shorted Circuit
EST 8 Open Circuit
EST 8 Shorted Circuit
Fuel Injector 1 Open Circuit
Fuel Injector 1 Shorted Circuit
Fuel Injector 2 Open Circuit
Fuel Injector 2 Shorted Circuit
Fuel Injector 3 Open Circuit
Fuel Injector 3 Shorted Circuit
Fuel Injector 4 Open Circuit
Page 1 of 4
10-20-04
CDS – ECM 555/ PCM 555/ PCM 03 Master Fault List
NOTE: All faults are not used on each engine
MerCruiser Fault #
66
67
68
69
70
71
72
73
74
75
76
77
78 and 79
80
81
82 and 83
84
85
86 - 88
89
90
91
92
93
94
95 and 96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
MerCruiser Fault Description
Fuel Injector 4 Shorted Circuit
Fuel Injector 5 Open Circuit
Fuel Injector 5 Shorted Circuit
Fuel Injector 6 Open Circuit
Fuel Injector 6 Shorted Circuit
Fuel Injector 7 Open Circuit
Fuel Injector 7 Shorted Circuit
Fuel Injector 8 Open Circuit
Fuel Injector 8 Shorted Circuit
Fuel Level 1 Circuit High
Fuel Level 1 Circuit Low
Camshaft Sensor Fault
Reserved
Main Power Relay Output
Main Power Relay Backfeed
Not used by MerCruiser
Oil Pressure Circuit High
Oil Pressure Circuit Low
Not used by MerCruiser
Oil Temperature Circuit High (Racing models only)
Oil Temperature Circuit Low (Racing models only)
Oil Temperature Overheat (Racing models only)
Paddle Wheel Sensor Fault
Pitot Pressure Circuit High
Pitot Pressure Circuit Low
Not used by MerCruiser
Port Tab Circuit High
Port Tab Circuit Low
Port Tab Down Solenoid Output
Port Tab Up Solenoid Output
CAN Comm. Fault Type 1
CAN Comm. Fault Type 2
CAN Comm. Fault Type 3
Lake/Sea Temp Circuit High
Lake/Sea Temp Circuit Low
Shift Actuator Driver Overtemp
Shift Actuator FeedBack High
Shift Actuator Feedback Low
Shift Actuator No Adapt
Shift Position Switch Fault
ECT Circuit High
ECT Circuit Low
Starboard Tab Circuit High
Starboard Tab Circuit Low
Starboard Tab Down Solenoid Output
Starboard Tab Up Solenoid Output
Start Solenoid Output
Steering Position Circuit High
Steering Position Circuit Low
TPS 1 Circuit High
TPS 1 Circuit Low
TPS 1 Range High
Page 2 of 4
10-20-04
CDS – ECM 555/ PCM 555/ PCM 03 Master Fault List
NOTE: All faults are not used on each engine
MerCruiser Fault #
123
124
125
126
127
128
129
130
131
132
133
134
135
136 and 137
138
139 - 147
148
149
150
151
152
153
154
155
156
157
158
159
160
161 and 162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
MerCruiser Fault Description
TPS 1 Range Low
TPS 1 No Adapt
TPS 2 Circuit High
TPS 2 Circuit Low
TPS 2 Range High
TPS 2 Range Low
TPS 2 No Adapt
Trim Sensor Circuit High
Trim Sensor Circuit Low
Crank Position Sensor Fault
Power 1 Volts (5VDC) Low
Overspeed 1
Overspeed 2
Not used by MerCruiser
ECM Memory Fault
Reserved
ESC and Neutral Switch Position Fault
ETC Idle Range Fault
Multiple CAN Circuit Faults
Fuel Pump Relay Circuit
IAC Output
Drive Lube Bottle Low
Mass Airflow too High
Secondary Map Sensor Circuit High
Secondary Map Sensor Circuit Low
Secondary Map Sensor Idle Fault
Port EMCT Circuit High
Port EMCT Circuit Low
Port EMCT Overheat
Reserved
CAN Comm. Fault Type 5
Secondary Fuel Injector 1 Short Circuit
Secondary Fuel Injector 1 Open Circuit
Secondary Fuel Injector 2 Short Circuit
Secondary Fuel Injector 2 Open Circuit
Secondary Fuel Injector 3 Short Circuit
Secondary Fuel Injector 3 Open Circuit
Secondary Fuel Injector 4 Short Circuit
Secondary Fuel Injector 4 Open Circuit
Secondary Fuel Injector 5 Short Circuit
Secondary Fuel Injector 5 Open Circuit
Secondary Fuel Injector 6 Short Circuit
Secondary Fuel Injector 6 Open Circuit
Shift Actuator Position Sensor Fault
Starboard EMCT Circuit High
Starboard EMCT Circuit Low
Starboard EMCT Overheat
MAP/TPI Difference Fault
TPI Sensors (All)
TPS 1 Difference Fault
TPS 2 Difference Fault
Trim Down Relay Output
Page 3 of 4
10-20-04
CDS – ECM 555/ PCM 555/ PCM 03 Master Fault List
10-20-04
NOTE: All faults are not used on each engine
MerCruiser Fault #
185
186
187
188
189
190
191
192
193
194
195
196
197 -208
209
210
211
212
213 and 214
215
216
217
218
219
220 – 225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243*
244*
245*
MerCruiser Fault Description
Trim Up Relay Output
CAN Comm. Fault Type 7
CAN Comm. Fault Type 8
Primary Demand to Redundant Diff
Demand Cross Check Difference
Shift Cross Check Difference
Fuel Level 2 Circuit High
Fuel Level 2 Circuit Low
Shift Anticipate Switch Fault
ESC Timeout Fault
Not used by MerCruiser
Transmission Overheat
Not used by MerCruiser
Driver Power Low
Overspeed in Neutral
Overspeed in Reverse
Start Failed – No RPM Detected
Not used by MerCruiser
CAN Comm. Fault Type 9
CAN Comm. Fault Type 10
Power 2 (5 VDC) Volts Low
Helm ADC Check
ESC Loss of Control
Not used by MerCruiser
CAN Comm. Fault Type 11
Hydraulic Shift Pressure Sensor A Circuit Low
Hydraulic Shift Pressure Sensor A Circuit High
Hydraulic Shift Pressure Sensor A Undefined
Hydraulic Shift Pressure Sensor B Circuit Low
Hydraulic Shift Pressure Sensor B Circuit High
Hydraulic Shift Pressure Sensor B Undefined
Hydraulic Shift System Fault
Hydraulic Shift System Pressure too high
Hydraulic Shift System Position Fault
Emergency Stop Activated
Excessive Knock Detected
Overspeed in Trailer Mode
Underwater Impact
Low Battery
Manifold Air Temp Overheat
Fuel Vent Purge Valve
Center Tab Circuit High
Center Tab Circuit Low
Shift Switch 2 Fault
Note: Faults 101, 102, 103, 150, 163, 186, 187, 212, 215, 216 and 226
will receive the text changes (as shown in this chart) in CDS Version
5.XX
*Faults 243 thru 245 will be added to CDS in Version 5.XX
Page 4 of 4
DTS Command Module Faults
DTS
System View Text
Fault # (MY04/Ver 3.33)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Warning Device Open
Lever 1 HIRES Range
Lever 1 INC Range
Lever 1 DEC Range
Lever 1 HIRES Diff
Lever 1 INC Diff
Lever 1 DEC Diff
Lever 1 Multiple
Lever 2 HIRES Range
Lever 2 INC Range
Lever 2 DEC Range
Lever 2 HIRES Diff
Lever 2 INC Diff
Lever 2 DEC Diff
Lever 2 Multiple
Primary Ctrl SOH
System View Text
(MY05/Ver 3.42)
CDS (Version 3.23 or higher)
Text (MY 04 and MY05)
Guardian
Sticky/Non-Sticky
Pin #
Color Code
(Single/Stbd)
Color Code
(Dual/Port)
Warning Device Open
Warning Horn Output
Lever 1 Fault 2
Lever 1 High Resolution Circuit
High or Low
The circuit is open or shorted between the Command
module and the ERC, or the "pot" in the ERC is open
or shorted
NA
NA
24
TAN/LT-BLU
TAN/LT-BLU
Lever 1 Fault 3
Lever 1 Increasing Circuit High
or Low
The circuit is open or shorted between the Command
module and the ERC, or the "pot" in the ERC is open
or shorted
65%
Non-Sticky
5
BLU/YEL
BLU/RED
65%
Non-Sticky
17
PNK/BRN
PNK/YEL
Lever 1 Fault 4
Lever 1 Decreasing Circuit High The circuit is open or shorted between the Command
module and the ERC, or the "pot" in the ERC is open
or Low
or shorted
Lever 1 Fault 5
Lever 1 High Resolution
Difference Error
65%
Non-Sticky
4
PNK/RED
PNK/DK-BLU
When compared to the other 2 "pots", the ERC's High
Resolution pot is reading wrong. Faulty Pot or circuit.
Lever 1 Fault 6
Lever 1 Increasing Circuit
Difference Error
65%
Sticky
5
BLU/YEL
BLU/RED
When compared to the other 2 "pots", the ERC's
Increasing pot is reading wrong. Faulty Pot or circuit.
Lever 1 Fault 7
Lever 1 Decreasing Circuit
Difference Fault
65%
Sticky
17
PNK/BRN
PNK/YEL
65%
Sticky
4
PNK/RED
PNK/DK-BLU
5%
Sticky
The circuit is open or shorted between the Command
module and the ERC (or Foot Throttle), or the "pot" in
the ERC (or Foot Throttle) is open or shorted
65%
Non-Sticky
16
GRN/YEL
GRN/BLK
The circuit is open or shorted between the Command
module and the ERC (or Foot Throttle), or the "pot" in
the ERC (or Foot Throttle) is open or shorted
65%
Non-Sticky
3
GRN/ORN
PNK/ORN
Lever 2 Decreasing Circuit High The circuit is open or shorted between the Command
or Low
module and the ERC(or Foot Throttle), or the "pot" in
the ERC(or Foot Throttle) is open or shorted
65%
Non-Sticky
15
GRN/RED
GNR/BLU
Lever 2 High Resolution
Difference Error
When compared to the other 2 "pots", the ERC's (or
Foot Throttle's) High Resolution pot is reading wrong.
Faulty Pot or circuit.
65%
Sticky
16
GRN/YEL
GRN/BLK
Lever 2 Increasing Circuit
Difference Error
When compared to the other 2 "pots", the ERC's (or
Foot Throttle's) Increasing pot is reading wrong.
Faulty Pot or circuit.
65%
Sticky
3
GRN/ORN
PNK/ORN
Lever 2 Decreasing Circuit
Difference Fault
When compared to the other 2 "pots", the ERC's (or
Foot Throttle's) decreasing pot is reading wrong.
Faulty Pot or circuit.
65%
Sticky
15
GRN/RED
GNR/BLU
Lever 2 Fault 15
Lever 2 Multiple Circuit Fault
More than one Lever 2 Fault is active (2 or more
Lever 2 faults are active). The other faults will be
listed individually. Fix Faults 9 thru 14 (as needed)
and this fault will go away.
5%
Sticky
CAN 2 Fault 16
Primary Control Data Failure
(PCM may show CAN Circuit
Fault 1)
The Data for control of the ETC and ESC actuators
has not been received (on the CAN 2 bus) when
expected.
65%
Non-Sticky
Lever 1 Fault 8
Lever 2 Fault 9
Lever 2 Fault 10
Lever 2 Fault 11
Lever 2 Fault 12
Lever 2 Fault 13
Lever 2 Fault 14
Lever 1 Multiple Circuit Fault
Lever 2 High Resolution Circuit
High or Low
Lever 2 Increasing Circuit High
or Low
What's probably wrong
The command module has detected a problem with
its warning horn circuit.
When compared to the other 2 "pots", the ERC's
decreasing pot is reading wrong. Faulty Pot or circuit.
More than one Lever 1 Fault is active (2 or more
Lever 1 faults are active). The other faults will be
listed individually. Fix Faults 2 thru 7 (as needed)
and this fault will go away.
Page 1 of 2
6&7
YEL and BRN in YEL and BRN in
the CAN Bus
the CAN Bus
DTS Command Module Faults
DTS
System View Text
Fault # (MY04/Ver 3.33)
17
18
19
Reduntant Ctrl SOH
Med Spd Eng Data SOH
Lo Spd Eng Data SOH
System View Text
(MY05/Ver 3.42)
CAN 1 Fault 17
CAN 1 Fault 18
CDS (Version 3.23 or higher)
Text (MY 04 and MY05)
Reduntant Control Data Failure
(PCM may show CAN Circuit
Fault 3)
Medium Speed Engine Data
Fault (PCM may show Can
Circuit Fault 3)
What's probably wrong
Low Speed Engine Data Fault
The backup data for the control of the ETC and ESC
actuators has not been received (on the CAN 1 Bus)
when expected.
The medium speed engine data (from the PCM) has
not been received (on the CAN 1 bus) when
expected. See Note 1.
The low speed engine data (from the PCM) has not
been received (on the CAN 1 bus) when expected.
See Note 2.
CAN 1 Fault 19
Pin #
65%
Non-Sticky
8&9
WHT and BLU WHT and BLU in
in the CAN Bus
the CAN Bus
NA
NA
8&9
WHT and BLU WHT and BLU in
in the CAN Bus
the CAN Bus
NA
NA
8&9
WHT and BLU WHT and BLU in
in the CAN Bus
the CAN Bus
6&7
YEL and BRN in YEL and BRN in
the CAN Bus
the CAN Bus
20
Multiple Eng Fault
DTS Fault 20
Multiple Engine Fault
Unknown at this time
NA
NA
Failsafe Mode Fault
DTS Fault 21
FailSafe Mode Fault
Unknown at this time
65%
Non-Sticky
DTS Fault 22
ETC/ESC Crosscheck Data
Failure (PCM may show Can
Circuit Fault 9)
The Crosscheck Data for control of the ETC and ESC
actuators (from the PCM) has not been received when
expected.
65%
Non-Sticky
DTS Fault 23
TPS% Crosscheck Difference
Fault
The PCM and Command Module are disagreeing on
the throttle plate's position. See Note 3
E-stop
Non-Sticky
Shift% Crosscheck Difference
Fault
The PCM and Command Module are disagreeing on
the shift actuator's position. See Note 3
E-stop
Non-Sticky
Advancing Throttle Fault
Rpm Data from the PCM (on the CAN 2 bus) has not
been received when expected. Used for
synchronization. Fastest possible update rate.
65%
Non-Sticky
23
24
25
Crosscheck SOH
TPS Crosscheck Diff
Shft Crosscheck Diff
(Not used in MY 04)
NOTE: Not all codes may be
turned on in each DTS
Command Module
Calibration
DTS Fault 24
DTS Fault 25
NOTE: DTS Faults are read
through the CAN 1 circuits
with the 84-892663 CAN 1
Cable
Color Code
(Dual/Port)
Sticky/Non-Sticky
21
22
Color Code
(Single/Stbd)
Guardian
Note 1: The medium speed engine data (updated at
a moderate rate) contains information on RPM, Fuel
Flow and pressure, MAP, Gear Position, Speed (pitot
and paddle), Trim Angle, Steering, Trim Tabs and
Warning System data.
Note 2: The low speed engine data (updated the
slowest) contains information on the Engine State,
Guardian, Run Time, Break-in, Fuel Level(s), Oil
system, Cooling System, Barometric, Battery Voltage,
Depth and Sea temp data.
Note 3: On these faults, the PCM sends the raw AD
counts of the sensor to the Command Module thru the
CAN Bus. The Command Module then calculates the
sensor's position and compares it to the PCM's
calculated position. If they disagree, the Command
Module sets the appropriate fault.
Page 2 of 2
9/7/2004
Helm 1
Helm 2
Helm 3
Helm 4
DTS Command Module "City ID's"
Single
Twins
Triples
Starboard Outer
Port Outer
Starboard Inner
91
92
93
95
96
97
99
9A
9B
9D
9E
9F
Quads
Port Inner
94
98
9C
Not supported
Note 1:
The important thing is that each command module has its own location (id)
CDS may incorrectly display the helm id's in triple and quad setups.
The City ID numbers will be correct, but they may appear in the wrong box
in the "DTS CMD MOD Info" screen grid. Version 5.XX will be correct.
Note 2:
If multiple helms have the same address, you will not be able to see
the individual modules, they will be "Stacked" on the single address.
Note 3:
The "Ver" number shown above the CityID in CDS is the DTS
Command Module software version.
Version "0" is Model Year 04 (used with the Yellow 10-pin CAN cable)
Version "6X" (61 through 69) is Model Year 05 (used with the Black 14-pin CAN cable)
You must not intermix different model year DTS Command Modules.
The model year of the DTS Command Module must match the model year of the PCM calibration.
10/20/2004
MEFI / ECM / PCM Pin Locations
•
•
•
•
•
•
•
•
•
MEFI 1, 2 and 3
ECM 555
PCM 555 and PCM 03
DTS Command Module (and CAN Circuit)
ETC (Electronic Throttle Control), ESC (Electronic Shift Control)
System View
MC Thunderbolt V
MC High-Performance HP525EFI PCM
MC High-Performance HP1075SCi PCM
MerCruiser MEFI 1, 2 and 3 Pinouts
J11
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#24 & #25 SB/V6
MEFI 1&2 - J1
Function
Knock Signal
ECT Signal
Empty
Discrete Input (not used)?
Master/Slave
Discrete Input (used)
Diagnostic IN
Empty
MAP Signal
TP Signal
Key B+
Empty
Sensor Ground (tp)
ECM Ground
Vref-TP
Battery +
Empty
Serial Data
Shift Switch IN**
Empty
Lanyard Stop*
Empty
Empty
Empty
Empty
Empty
Empty
Empty
Sensor Ground (map/ect)
ECM Ground
Vref-MAP
Battery +
Color
GRN
YEL
BRN
YEL
BRN
BLK/WHT
LT-GRN
DK-BLU
PNK/BLK
BLK
BLK/WHT
GRY
ORN
ORN/BLK
WHT
PNK
BLK
BLK/WHT
GRY
ORN
J21
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#24 & #25 SB/V6
MEFI 1&2 - J2
Function
Empty
Empty
Empty
Empty
Injector Driver "B"
Reference Low
MPI Fuel Jumper
Reference High
Fuel Pump Relay Driver
Empty
Horn Driver (ECT)
Empty
IAC "A" Low
IAC "B" High
Injector Ground
Empty
Empty
Empty
Empty
Injector Ground
Injector Driver "A"
MPI Fuel Jumper
Ignition Control Signal
Ignition Bypass
Empty
Discrete Switch???
Horn Driver (switches)
IAC "A" High
IAC "B" Low
Empty
CEL / MIL Driver
Empty
Color
LT-GRN
RED/BLK*
WHT
PPL/WHT
DK-GRN/WHT
DK-GRN
RED (BLU/BLK)
YEL (GRN/WHT)
BLK/WHT
BLK/WHT
DK-BLU
WHT
WHT
TAN/BLK
TAN
TAN
BRN (BLU/WHT)
GRN/BLK
BRN/WHT
*or BLK/RED?
*MEFI 1
**MEFI 2
Color codes in ( ) are
late MEFI 1 & all MEFI 2
Page 1 of 6
MerCruiser MEFI 1, 2 and 3 Pinouts
J11
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#24 & #25 SB/V6
MEFI 3 - J1
Function
Injector Driver "B"
Ignition Coil Driver*
Reference Low
ECM Ground
ECM Ground
Empty
Empty
Empty
CEL / MIL Driver
Ignition Control Signal
IAC "B" High
IAC "A" Low
Empty
Empty
Empty
Empty
Injector Driver "A"
Empty
Empty
ECM Ground
Empty
Empty
Fuel Pump Relay Driver
Ignition Bypass
Empty
Horn Driver (ALL)
IAC "B" Low
IAC "A" High
Empty
Knock Signal (sensor 1)
Empty
Serial Data
*Thunderbolt system only
Color
DK-BLU
WHT
RED/BLK*
BLK
BLK
J2-
BRN/WHT
WHT
GRN/WHT
BLU/BLK
DK-GRN
BLK
DK-GRN/WH
TAN/BLK
DK-GRN
GRN/BLK
BLU/WHT
BLU
ORN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#24 & #25 SB/V6
MEFI 3 - J2
Function
Battery +
Empty
Sensor Ground (TP, FP, IAT)
Vref (TP and FP)
Empty
Empty
Discrete Switch (oil pressure)
Discrete Switch (trans temp)
Shift Interrupt
Reference High
ECT Signal
Fuel Pressure Signal
Empty
Empty
Empty
Empty
Empty
Sensor Ground (ECT & MAP)
Vref (MAP)
Discrete Switch (Load Ant.)
Master/Slave
Diagnostic IN
Empty
Discrete Switch (lube bottle)
Empty
TP Signal
MAP Signal
Empty
Empty
IAT Sensor
Empty
Key B+
*BLK/RED?
Page 2 of 6
Color
ORN
BLK
GRY
BLU
TAN/WHT
PPL
PPL/WHT
YEL
GRN
BLK
GRY
BRN
YEL
BLK/WHT
TAN/WHT
DK-BLU
LT-GRN
TAN
PNK
MerCruiser MEFI 1, 2 and 3 Pinouts
J11
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#23 BB
MEFI 1 - J1
Function
Knock Signal
ECT Signal
Empty
Discrete Input (not used)?
Master/Slave
Discrete Input (used)
Diagnostic IN
Empty
MAP Signal
TP Signal
Key B+
Empty
Sensor Ground (tp & iat)
ECM Ground
Vref-TP
Battery +
Empty
Serial Data
Empty
Empty
Lanyard Stop
Empty
Empty
IAT Signal
Empty
Empty
Empty
Empty
Sensor Ground (map/ect)
ECM Ground
Vref-MAP
Battery +
Color
BLK
YEL
YEL
BRN
WHT/BLK
LT-GRN
DK-BLU
PNK/BLK
BLK
BLK/WHT
GRY
ORN
ORN/BLK
PNK
TAN
BLK
BLK/WHT
GRY
ORN
J21
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#23 BB
MEFI 1 - J2
Function
Empty
Empty
Empty
Empty
Injector Driver "B"
Reference Low
MPI Fuel Jumper
Reference High
Fuel Pump Relay Driver
Empty
Horn Driver (ECT)
Empty
IAC "A" Low
IAC "B" High
Injector Ground
Empty
Empty
Empty
Empty
Injector Ground
Injector Driver "A"
MPI Fuel Jumper
Ignition Control Signal
Ignition Bypass
Empty
Empty
Horn Driver (switches)
IAC "A" High
IAC "B" Low
Empty
CEL / MIL Driver
Empty
Page 3 of 6
Color
LT-GRN
BLK/RED
WHT
PPL/WHT
DK-GRN/WH
DK-GRN
BLU/BLK
GRN/WHT
BLK/WHT
BLK/WHT
DK-BLU
WHT
WHT
TAN/BLK
TAN
BLU/WHT
GRN/BLK
BRN/WHT
MerCruiser MEFI 1, 2 and 3 Pinouts
J11
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#23 BB L29
MEFI 2 - J1
Function
Knock Signal
ECT Signal
Empty
Discrete Input (early)
Master/Slave
Discrete Input (late)
Diagnostic IN
Empty
MAP Signal
TP Signal
Key B+
Empty
Sensor Ground (tp & iat)
ECM Ground
Vref-TP
Battery +
Empty
Serial Data
Empty
Empty
Empty
Empty
Empty
IAT Signal
Empty
Empty
Empty
Empty
Sensor Ground (map/ect)
ECM Ground
Vref-MAP
Battery +
Color
GRN
YEL
BRN
YEL
BRN
BLK/WHT
LT-GRN
DK-BLU
PNK (PNK/BLK)
BLK
BLK
GRY
ORN
ORN
TAN
BLK
BLK
GRY
ORN
J21
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#23 BB L29
MEFI 2 - J2
Function
Empty
Empty
Empty
Empty
Injector Driver "B"
Reference Low
MPI Fuel Jumper
Reference High
Fuel Pump Relay Driver
Empty
Horn Driver (ECT)
Empty
IAC "A" Low
IAC "B" High
Injector Ground
Empty
Empty
Empty
Empty
Injector Ground
Injector Driver "A"
MPI Fuel Jumper
Ignition Control Signal
Ignition Bypass
Empty
Horn Driver (switches)
Empty
IAC "A" High
IAC "B" Low
Empty
CEL / MIL Driver
Empty
Color in ( ), not sure of correct color,
Manual has conflicting information
Color
DK-GRN
RED/BLK*
BLK (WHT)?
PPL/WHT
DK-GRN/WHT
DK-GRN (GRY)?
LT-BLU/BLK
LT-GRN/WHT
BLK (BLK/WHT)
BLK (BLK/WHT)
DK-BLU
BLK (WHT)?
WHT
TAN/BLK
DK-GRN
LT-BLU/WHT
LT-GRN/BLK
BRN/WHT
*or BLK/RED?
Page 4 of 6
MerCruiser MEFI 1, 2 and 3 Pinouts
J11
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#23 BB
MEFI 3 - J1
Function
Injector Driver "B"
Empty
Reference Low
ECM Ground
ECM Ground
Empty
Empty
Empty
CEL / MIL Driver
Ignition Control Signal
IAC "B" High
IAC "A" Low
Empty
Knock Signal (sensor 2)
Empty
Empty
Injector Driver "A"
Empty
Empty
ECM Ground
Empty
Empty
Fuel Pump Relay Driver
Ignition Bypass
Empty
Horn Driver (ALL)
IAC "B" Low
IAC "A" High
Empty
Knock Signal (sensor 1)
Empty
Serial Data
Color
DK-BLU
RED/BLK*
BLK
BLK
BRN/WHT
WHT
GRN/WHT
BLU/BLK
BLU
DK-GRN
BLK
DK-GRN/WHT
TAN/BLK
DK-GRN
GRN/BLK
BLU/WHT
BLU
ORN
J21
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#23 BB
MEFI 3 - J2
Function
Battery +
Empty
Sensor Ground (TP & IAT)
Vref (TP)
Empty
Empty
Discrete Switch (oil pressure)
Discrete Switch (trans temp)
Empty
Reference High
ECT Signal
Empty
Empty
Empty
Empty
Empty
Empty
Sensor Ground (ECT & MAP)
Vref (MAP)
Discrete Switch (Load Ant.)
Master/Slave
Diagnostic IN
Empty
Discrete Switch (lube bottle)
Empty
TP Signal
MAP Signal
Empty
Empty
IAT Sensor
Empty
Key B+
*BLK/RED?
Page 5 of 6
Color
ORN
BLK
GRY
BLU
TAN/WHT
PPL/WHT
YEL
BLK
GRY
WHT (BRN)?
YEL
BLK/WHT
TAN/WHT
DK-BLU
LT-GRN
TAN
PNK
MerCruiser MEFI 1, 2 and 3 Pinouts
J11
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#16, 17 & 18
MEFI 1 - J1
Function
Knock Signal
ECT Signal
Empty
Empty
Master/Slave
Discrete Input (used)
Diagnostic IN
Empty
MAP Signal
TP Signal
Key B+
Empty
Sensor Ground (tp & iat)
ECM Ground
Vref-TP
Battery +
Empty
Serial Data
Empty
Empty
Lanyard Stop
Empty
Empty
IAT Signal
Empty
Empty
Empty
Empty
Sensor Ground (map/ect)
ECM Ground
Vref-MAP
Battery +
Color
BLK
YEL
YEL
BRN
WHT/BLK
LT-GRN
DK-BLU
PNK/BLK
BLK
BLK/WHT
GRY
ORN
ORN/BLK
PNK
TAN
BLK
BLK/WHT
GRY
ORN
J21
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SM#16, 17 & 18
MEFI 1 - J2
Function
Empty
Empty
Empty
Empty
Injector Driver "B"
Reference Low
MPI Fuel Jumper
Reference High
Fuel Pump Relay Driver
Empty
Horn Driver (ECT)
Empty
IAC "A" Low
IAC "B" High
Injector Ground
Empty
Empty
Empty
Empty
Injector Ground
Injector Driver "A"
MPI Fuel Jumper
Ignition Control Signal
Ignition Bypass
Empty
Empty
Horn Driver (switches)
IAC "A" High
IAC "B" Low
Empty
CEL / MIL Driver
Empty
Color
LT-GRN
BLK/RED
WHT
PPL/WHT
DK-GRN/WHT
DK-GRN
BLU/BLK
GRN/WHT
BLK/WHT
BLK/WHT
DK-BLU
WHT
WHT
TAN/BLK
TAN
BLU/WHT
GRN/BLK
BRN/WHT
10/20/2004
Page 6 of 6
ECM555 MerCruiser Pinouts
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
ECM555 Mercruiser
Empty
Fuel Injector Bank 2 driver
Empty
CAN 1 (+)
Scan Tool (-)
Knock Odd (-) V8
Knock Even (-) V6
TransTemp/Lube Bottle
Warning Horn driver
Tach Signal Out
CAN 1 (-)
Scan Tool (+)
Knock Odd (+) V8
Knock Even (+) V6
E-Stop (thru CAN bus)
Ground
Fuel Injector Bank 1 driver
Empty
Fuel Pump Relay Control
IAC Valve Control
Gear Position Switch
MPR control
MPR Output (to ECM)
Ground
ECM555 MerCruiser
Sender Ground
MAT Signal
MAP Signal
Fuel Level 1 Signal
Empty
Empty
Oil Pressure Signal
Steering Angle Signal
PaddleWheel Signal
Crank Position Signal
SeaPump Signal
Pitot Signal
DigitalTrim Signal
ECT Signal
Empty
Empty
Empty
Wakeup (key-switch B+)
Shift Interrupt Signal
TPS Signal
Sender Power (Power 1)
SeaTemp Signal
EST Trigger (coil control)
Empty
V6 Alpha/Bravo
Color Code V6
Empty
LT-GRN/WHT
Empty
WHT
WHT/PPL
Empty
YEL/DK-BLU
DK-BLU/BRN
BRN/DK-BLU
GRY/WHT
LT-BLU
WHT/BLK
Empty
DK-BLU/YEL
DK-GRN/YEL
BLK
LT-GRN/PPL
Empty
DK-GRN
BLK/DK-GRN
YEL/DK-GRN
PPL/DK-GRN
PNK
BLK
Color Code V6 MCM
BLK/PNK
BRN/YEL
LT-GRN
LT-BLU/BLK
Empty
Empty
DK-BLU/BLK
PNK/DK-BLU
GRY/BLK (YEL/GRY)
TAN/BLK
DK-BLU/WHT
WHT/LT-BLU
ORN/WHT
YEL
Empty
Empty
Empty
PPL
YEL/PPL
DK-BLU/ORN
GRY
LT-BLU/ORN (WHT/YEL)
WHT/DK-GRN
Empty
V8 Alpha/Bravo
Color Code V8 MCM
Empty
LT-GRN/WHT
Empty
WHT
WHT/PPL
ORN/BLK
YEL/DK-BLU (Empty)
DK-BLU/BRN
BRN/DK-BLU
GRY/WHT
LT-BLU
WHT/BLK
BLK/ORN
DK-BLU/YEL (Empty)
DK-GRN/YEL
BLK
LT-GRN/PPL
Empty
DK-GRN
BLK/DK-GRN
YEL/DK-GRN
PPL/DK-GRN
PNK
BLK
Color Code V8 MCM
BLK/PNK
BRN/YEL
LT-GRN
LT-BLU/BLK
Empty
Empty
DK-BLU/BLK
PNK/DK-BLU
GRY/BLK (YEL/GRY)
TAN/BLK
DK-BLU/WHT
WHT/LT-BLU
ORN/WHT
YEL
Empty
Empty
Empty
PPL
YEL/PPL
DK-BLU/ORN
GRY
GRY/BLK (YEL/GRY)
WHT/DK-GRN
Empty
NOTE: PaddleWheel and SeaTemp appear
to have changed colors, current colors are in (XXX)
Page 1 of 2
V8 Inboard
Color Code V8 MIE
Empty
LT-GRN/WHT
Empty
WHT
WHT/PPL
ORN/BLK
Empty
DK-BLU/BRN
BRN/DK-BLU
GRY/WHT
LT-BLU
WHT/BLK
BLK/ORN
Empty
DK-GRN/YEL
BLK
LT-GRN/PPL
Empty
DK-GRN
BLK/DK-GRN
YEL/DK-GRN
PPL/DK-GRN
PNK
BLK
Color Code MIE
BLK/PNK
BRN/YEL
LT-GRN
PNK/BLK
Empty
Empty
DK-BLU/BLK
PNK/DK-BLU
GRY/BLK (YEL/GRY)
TAN/BLK
DK-BLU/WHT
WHT/LT-BLU
LT-BLU/BLK (FUEL 2)
YEL
Empty
Empty
Empty
PPL
Empty
DK-BLU/ORN
GRY
GRY/BLK (YEL/GRY)
WHT/DK-GRN
Empty
NOTE: MIE models are
wired for 2 fuel tanks
ECM555 MerCruiser Pinouts
Note: V6 Stern Drives are wired only for one knock sensor, early V8 models were wired for 2,
but only one knock sensor was connected (to the knock "odd" leads).
Current V8 are wired for only one knock sensor.
Splices
100
101
102
103
104
104A
105
106
107
108
109
110
111
112
113
114
115
Function (ECM555SD)
Sender Ground
Sender Power
Key-Switch B+ (wake)
B+ (pre-fuse, post breaker)
Engine Ground
Engine Ground (aux)
MPR Output (pre-fuse)
MPR Output (post-fuse)
MPR Output (post-fuse)
MPR Output (post-fuse)
LubeBottle/TransTemp
Fuel Injector Bank 1
Fuel Injector Bank 2
Ignition Coil & Driver
Tach signal out
NOT USED
NOT USED
Color Code V6 MCM
BLK/PNK
GRY
PPL
RED/PPL
BLK
BLK
RED/BLK
PNK
PNK/LT-GRN
PNK/WHT
DK-BLU/BRN
LT-GRN/PPL
LT-GRN/WHT
WHT/LT-GRN
GRY/WHT
Color Code V8 MCM
BLK/PNK
GRY
PPL
RED/PPL
BLK
BLK
RED/BLK
PNK
PNK/LT-GRN
PNK/WHT
DK-BLU/BRN
LT-GRN/PPL
LT-GRN/WHT
WHT/LT-GRN
GRY/WHT
Color Code MIE
BLK/PNK
GRY
PPL
RED/PPL
BLK
BLK
RED/BLK
PNK
PNK/LT-GRN
PNK/WHT
Not Used
LT-GRN/PPL
LT-GRN/WHT
WHT/LT-GRN
GRY/WHT
10/20/2004
Page 2 of 2
PCM555/PCM03 MerCruiser Pinouts
NOTE:
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
This chart only valid with models
not equipped with 14 pin CAN Bus
496/8.1L MerCruiser
Wakeup (Key-Switch B+)
Shift Position Signal (from ESC)
MAP Signal
Oil Pressure Signal
Pitot Signal
TP1 Signal
TP2 Signal
Digital Trim Signal
Stbd Tab Position Signal
Port Tab Position Signal
CAN 1 (+)
Steering Angle Signal
SeaTemp Signal
MAT Signal
ECT Signal
Port EMCT Signal
Stbd EMCT Signal
Scan Tool (-)
Knock 1 (-)
Knock 2 (-)
CAN 1 (-)
Sender Ground
Sender Power (Power 1 / Engine)
SeaPump Signal
Fuel Level 2 Signal
Fuel Level 1 Signal
Empty
Scan Tool (+)
Knock 1 (+)
Knock 2 (+)
CAN 2 (+)
CAN 2 (-)
Early "Mechanical"
2-piece Harness
Color-mech
PNK
Empty
LT-GRN
DK-BLU/BLK
LT-BLU/BLK
DK-BLU
Empty
ORN/DK-BLU
DK-BLU/YEL
LT-BLU
ORN
LT-BLU/BLK
YEL/BLK
TAN
YEL
TAN/WHT
TAN/BLK
WHT/PPL
BLK/YEL
BLK/WHT
YEL/WHT
BLK/PNK
GRY
DK-BLU/YEL
LT-BLU/BLK
PNK/BLK
Empty
WHT/BLK
BLK/ORN
BLK/RED
ORN/DK-BLU
YEL/RED
Later "Integrated" 1-pc.
Harness (Mechanical)
Color-integrated
PPL
Empty
LT-GRN
DK-BLU/BLK
WHT/LT-BLU
DK-BLU/ORN
Empty
ORN/WHT
DK-BLU/RED
GRY/RED
WHT
PNK/DK-BLU
WHT/YEL
TAN/YEL
YEL
BRN/WHT
BRN/BLK
WHT/PPL
ORN/BLK
YEL/DK-BLU
LT-BLU
BLK/PNK
GRY
DK-BLU/WHT
LT-BLU/BLK
PNK/BLK
Empty
WHT/BLK
BLK/ORN
DK-BLU/YEL
DK-GRN/ORN
DK-GRN/RED
Page 1 of 4
Earyly DTS (MY03)
SysView = DTS
Color-DTS (MY03)
PPL
LT-BLU/YEL
LT-GRN
DK-BLU/BLK
WHT/LT-BLU
DK-BLU/ORN
BLK/LT-BLU
ORN/WHT
DK-BLU/RED
GRY/RED
WHT
PNK/DK-BLU
WHT/YEL
TAN/YEL
YEL
BRN/WHT
BRN/BLK
WHT/PPL
ORN/BLK
YEL/DK-BLU
LT-BLU
BLK/PNK
GRY
DK-BLU/WHT
LT-BLU/BLK
PNK/BLK
Empty
WHT/BLK
BLK/ORN
DK-BLU/YEL
DK-GRN/ORN
DK-GRN/RED
Late DTS (MY04)
DTS Cmd Module
Color-DTS (MY04)
PPL
BLU/GRN
LT-GRN
DK-BLU/BLK
WHT/LT-BLU
DK-BLU/ORN
BLK/BLU
ORN/WHT
DK-BLU/RED
GRY/RED
WHT
PNK/DK-BLU
WHT/YEL
TAN/YEL
YEL
BRN/WHT
BRN/BLK
WHT/PPL
ORN/BLK
YEL/GRN
LT-BLU
BLK/PNK
GRY
DK-BLU/WHT
LT-BLU/BLK
PNK/BLK
Empty
WHT/BLK
BLK/ORN
DK-BLU/YEL
DK-GRN/ORN
DK-GRN/RED
PCM555/PCM03 MerCruiser Pinouts
NOTE:
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
This chart only valid with models
not equipped with 14 pin CAN Bus
496/8.1L MerCruiser
EST Return
EST Coil #1 Trigger
PaddleWheel Signal
MPR control
Empty
Cam Sensor Signal
IAC Valve control
Assist Solenoid driver
EST Coil # 5 Trigger
EST Coil #3 Trigger
Fuel Pump Relay Control
Tach Signal out
Empty
Crank Position Signal
Gear Position Switch Signal
LubeBottle/TransTemp Signal
MPR Output (to PCM)
MPR Output (to PCM)
Empty
Fuel Injector #4 driver
Warning Horn driver
Fuel Injector #3 driver
E-Stop (thru CAN bus)
Power 2 (smartcraft sensors / PCM03)
Early "Mechanical"
2-piece Harness
Color-mech
BRN
WHT/RED
GRY/BLK
PPL
Empty
PPL/WHT
BLK/DK-GRN
EMPTY
WHT/PPL
WHT
DK-GRN
WHT
Empty
TAN
BRN
TAN/WHT
PNK
PNK
Empty
DK-GRN/YEL
TAN/BLK
DK-GRN/ORN
YEL/BLK
Empty
Later "Integrated" 1-pc.
Harness (Mechanical)
Color-integrated
BRN
WHT/BLK
YEL/GRY
PPL/DK-GRN
Empty
PPL/WHT
BLK/DK-GRN
EMPTY
WHT/LT-BLU
WHT/PPL
DK-GRN
GRY/WHT
Empty
TAN/BLK
YEL/DK-GRN*
DK-BLU/BRN
PNK/LT-GRN
PNK/LT-GRN
Empty
LT-GRN/BLK
BRN/DK-BLU
LT-GRN/LT-BLU
DK-GRN/YEL
Empty
Earyly DTS (MY03)
SysView = DTS
Color-DTS (MY03)
BRN
WHT/BLK
YEL/GRY
PPL/DK-GRN
Empty
PPL/WHT
EMPTY
YEL/BLK
WHT/LT-BLU
WHT/PPL
DK-GRN
GRY/WHT
Empty
TAN/BLK
YEL/DK-GRN
DK-BLU/BRN
PNK/LT-GRN
PNK/LT-GRN
Empty
LT-GRN/BLK
BRN/DK-BLU
LT-GRN/LT-BLU
DK-GRN/YEL
Empty
*This circuit is missing in Service manual #33
Page 2 of 4
Late DTS (MY04)
DTS Cmd Module
Color-DTS (MY04)
BRN
WHT/BLK
YEL/GRY
PPL/DK-GRN
Empty
PPL/WHT
EMPTY
YEL/BLK
WHT/LT-BLU
WHT/PPL
DK-GRN
GRY/WHT
Empty
TAN/BLK
YEL/DK-GRN
DK-BLU/BRN
PNK/LT-GRN
PNK/LT-GRN
Empty
LT-GRN/BLK
BRN/DK-BLU
LT-GRN/LT-BLU
DK-GRN/YEL
GRY/BLK
PCM555/PCM03 MerCruiser Pinouts
NOTE:
Pin
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
This chart only valid with models
not equipped with 14 pin CAN Bus
496/8.1L MerCruiser
PortTabUp Solenoid driver
ETC (pin 3) Motor "B"
Fuel Injector #8 driver
ETC (pin 5) Motor "A"
Fuel Injector #7 driver
Fuel Injector #1 driver
EST Coil #4 Trigger
EST Coil #2 Trigger
StbdTabUp Solenoid driver
StbdTabDn Solenoid driver
Fuel Injector #2 driver
EST Coil #6 Trigger
EST Coil #7 Trigger
EST Coil #8 Trigger
Ground
Ground
ESC (pin D) Motor "A"
ESC (pin E) Motor "B"
PortTabDn Solenoid driver
TrimDownRelay Control
Fuel Injector #6 driver
TrimUpRelay Control
Fuel Injector #5 driver
Ground
Early "Mechanical"
2-piece Harness
Color-mech
LT-BLU/RED
Empty
DK-GRN/BLK
Empty
BRN/WHT
LT-GRN/BLK
WHT/RED
WHT/BLK
LT-BLU/BLK
LT-GRN/BLK
LT-GRN/RED
WHT/LT-BLU
WHT/BLK
WHT
BLK
BLK
Empty
Empty
DK-GRN/WHT
LT_BLU/WHT
GRY/BLK
DK-BLU/WHT
BRN/DK-BLU
BLK
Later "Integrated" 1-pc.
Harness (Mechanical)
Color-integrated
BLK/LT-BLU
Empty
LT-GRN/DK-BLU
Empty
LT-GRN/BLK
LT-GRN/ORN
WHT/RED
WHT/DK-GRN
BLK/LT-GRN
GRY/DK-BLU
LT-GRN/PPL
WHT/LT-GRN
WHT/DK-BLU
WHT/PPL
BLK
BLK
Empty
Empty
GRY/DK-GRN
Empty
LT-GRN/RED
DK-BLU/RED
LT-GRN/WHT
BLK
Page 3 of 4
Earyly DTS (MY03)
with System View
Color-DTS (03)
BLK/LT-BLU
PPL/WHT
LT-GRN/DK-BLU
LT-BLU/WHT
LT-GRN/BLK
LT-GRN/ORN
WHT/RED
WHT/DK-GRN
BLK/LT-GRN
GRY/DK-BLU
LT-GRN/PPL
WHT/LT-GRN
WHT/DK-BLU
WHT/PPL
BLK
BLK
YEL/RED
YEL/LT-GRN
GRY/DK-GRN
DK-GRN/WHT
LT-GRN/RED
DK-BLU/RED
LT-GRN/WHT
BLK
Late DTS (MY04)
with Command Module
Color-DTS (MY04)
BLK/BLU
PPL/WHT
LT-GRN/DK-BLU
LT-BLU/WHT
LT-GRN/BLK
LT-GRN/ORN
WHT/RED
WHT/DK-GRN
BLK/LT-GRN
GRY/DK-BLU
LT-GRN/PPL
WHT/LT-GRN
WHT/DK-BLU
WHT/PPL
BLK
BLK
YEL/RED
YEL/GRN
GRY/DK-GRN
DK-GRN/YEL
LT-GRN/RED
DK-BLU/RED
LT-GRN/WHT
BLK
PCM555/PCM03 MerCruiser Pinouts
Splices
100
101
102
103
104
104A
105
106
107
108
109
110
111
112
113
114
115
Function (496/8.1L)
Sender Ground
Sender Power (Power 1)
Key-switch B+ (wake)
B+ (post-fuse)
Engine Ground
Engine Ground (aux)
MPR Output (pre-fuse)
EST Return
MPR Output (post-fuse)
MPR Output (post-fuse)
Sender Ground (aux)
B+ (pre-fuse, post breaker)
Fuel Pumps (post Fuel Pump Realy)
Unique
Not Used*
TACH signal out
LubeBottle/TransTemp
"Mechanical"
BLK/PNK
GRY
PNK
RED
BLK
Not used
RED
BRN
PNK
PNK
BLK/PNK
RED
PNK
BRN*
Not used
Not used
Not used
"Integrated"
BLK/PNK
GRY
PPL
PNK
BLK
BLK
RED/BLK
BRN
PNK/LT-GRN
PNK/WHT
Not used
RED/PPL
PNK/YEL
Not used
Not used*
GRY/WHT
DK-BLU/BRN
DTS (MY03)
BLK/PNK
GRY
PPL
PNK
BLK
BLK
RED/BLK
BRN
PNK/LT-GRN
PNK/WHT
Not used
RED/PPL
PNK/YEL
PPL/RED*
Not used
GRY/WHT
DK-BLU/BRN
*NSS circuit
*Splice 113 is listed
incorrectly in #33
Splice 114 is correct
number of this splice
*Trim up/down
relays (pin 30) &
Transom Harness
pin H
Page 4 of 4
10/20/2004
DTS Command Module (and CAN circuit) Pinout Information
MY 04/MY05
DTS Command
Module
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Service
Function
Sensor Ground
Wakeup (Key switch B+)
Lever 2 Increasing Signal
Lever 1 Decreasing Signal
Lever 1 HiResolution Signal
CAN 2 (-)
CAN 2 (+)
CAN 1 (-)
CAN 1 (+)
Start Signal Input
Neutral Switch Input
Synch LED driver
Power (12v)
Ground
Lever 2 Decreasing Signal
Lever 2 HiResoltion Signal
Lever 1 Increasing Signal
Sensor Power 5v (Power 1)
Trim Down input
Trim Up input
E-stop input
Active LED driver
Neutral LED driver
Horn Driver
Single Console/
Single Zero Effort
Color
BLK/ORN
PPL
GRN/ORN
PNK/RED
BLU/YEL
BRN
YEL
DK-BLU
WHT
YEL/RED
YEL/BLK
*
RED/PPL
BLK
GRN/RED
GRN/YEL
PNK/BRN
PPL/YEL
GRN/WHT
LT-BLU/WHT
BLK/YEL
GRY
WHT/YEL
TAN/LT-BLU
*Not used
Dual Console/
Dual Zero Effort
Color (STBD)
BLK/ORN
PPL
GRN/ORN
PNK/RED
BLU/YEL
BRN
YEL
DK-BLU
WHT
YEL/RED
YEL/BLK
*
RED/PPL
BLK
GRN/RED
GRN/YEL
PNK/BRN
PPL/YEL
GRN/WHT
LT-BLU/WHT
BLK/YEL
GRY
ORN
TAN/LT-BLU
*Not used
Page 1 of 3
Dual Console/
Dual Zero Effort
Color (PORT)
BLK/ORN
PPL
PNK/ORN
PNK/DK-BLU
BLU/RED
BRN
YEL
DK-BLU
WHT
YEL/GRN
YEL/BLK
TAN
RED/PPL
BLK
GRN/BLU
GRN/BLK
PNK/YEL
PPL/YEL
GRN
LT-BLU
BLK/YEL
GRY
WHT/YEL
TAN/LT-BLU
Single Engine
Panel Mount
Color
BLK/ORN
PPL
GRN/ORN
PNK/RED
BLU/YEL
BRN
YEL
DK-BLU
WHT
YEL/RED
YEL/BLK
*
RED/PPL
BLK
GRN/RED
GRN/YEL
PNK/BRN
PPL/YEL
GRN/WHT
LT-BLU/WHT
BLK/YEL
*
*
TAN/LT-BLU
*Not used
DTS Command Module (and CAN circuit) Pinout Information
System Link
Connectors
1
2
3
Function
Color (Harness)
Power (12v)
PPL/WHT
Ground
BLK
Data (VDO Bus)
YEL (single)*
*YEL/PPL (stbd)
*YEL/WHT (port)
Color (Gauges)
RED
BLU
YEL
On Console and Panel mounts, there is 1 "lever" on the ERC.
On Panel Mounts, "Lever 2" is the optional Foot Throttle.
On Zero Effort, there are 2 "levers",
Lever 1 is the Shift Lever and Lever 2 is the Throttle
All "levers" use a single piece proprietary potentiometer (5-wire)
with 3 separate signals. High Res(olution), Incr(easing), Decr(easing)
Pin A
Sensor Power
Pin B
Pot 1 (HiRes)
Reads 5 to 0 to 5 volts
Pin C
Pot 2 (Incr)
Reads 0 to 5 volts
Pin D
Pot 3 (Decr)
Reads 5 to 0 volts
Pin E
Sensor Ground
CAN BUS and
Typical
Junction Boxes
Function
Color
A
Power (12v)
RED
B
Ground
BLK
C
CAN 3 (+)
ORN
D
CAN 3 (-)
GRN
E
E-Stop
BLK/YEL
F
Wakeup
PPL
G
CAN 2 (+)
YEL
H
CAN 2 (-)
BRN
J
CAN 1 (+)
WHT
K
CAN 1 (-)
BLU
Note: On MY05 applications, Pin G may be GRY on
the helm side for "tach link" purposes.
CAN 3 will be Vessel System.
CAN 2 is ONLY Digital Throttle and Shift.
CAN 1 is gauges and backup for Digital Throttle
and Shift Commands.
Scan tools talk thru CAN 1.
MY 05 Deutsch 14 pin Main Engine Connector
Outboard
MerCruiser
MerCruiser
Pin
DTS Function
OB DTS Color DTS Function
DTS Color
A
Power (12V B+) RED/BLK
Power (12V B+)
PNK
B
Ground
BLK
Ground
BLK
C
Wakeup
PPL/WHT
Wakeup
PPL
D
E-Stop
BLK/YEL
E-Stop
GRN/YEL
E
Empty
-------Analog Oil Pressure BLU
F
CAN 1 (+)
WHT
CAN 1 (+)
WHT
G
CAN 1 (-)
DK-BLU
CAN 1 (-)
LT-BLU
H
Trim Up
LT-BLU/WHT*
Empty
Empty
J
Trim Down
GRN/WHT*
Empty
Empty
K
CAN 2 (+)
YEL
CAN 2 (+)
GRN/ORN
L
CAN 2 (-)
BRN
CAN 2 (-)
GRN/RED
M
Tach Signal
GRY
Tach Signal
GRY/WHT
N
Empty
Empty
Analog Trim
ORN/WHT
P
Empty
Empty
Analog Temp
TAN
*Wired to relay, but no connection at helm
Page 2 of 3
DTS Command Module (and CAN circuit) Pinout Information
MY 05 Deutsch 14 pin Main CAN Harness (Black Boat Cable)
Pin
Color Code
Outboard DTS Engines
A
RED
CAN B+ (from Clean Power)
B
BLK
Ground
C
PPL
Wake-up (Key Switched B+)
D
BLK/YEL
E-Stop (Key Switch/Lanyard Switch)
E
ORN
Not used
F
WHT
CAN 1(+), Gauge Data/Backup DTS
G
DK-BLU
CAN 1(-), Gauge Data/Backup DTS
H
LT-BLU/WHT
Not used on Helm end of harness
J
GRN/WHT
Not used on Helm end of harness
K
YEL
CAN 2 (+) Primary DTS commands
L
BRN
CAN 2 (-) Primary DTS commands
M
GRY
Tach Signal (analog)
N
YEL/RED
Not used
P
GRN
Not used
MerCruiser DTS Engines
CAN B+ (from Clean Power)
Ground
Wake-up (Key Switched B+)
E-Stop (Keyswitch/Lanyard Switch
Analog Oil Pressure Signal
CAN 1(+), Gauge Data/Backup DTS
CAN 1(-), Gauge Data/Backup DTS
Empty
Empty
CAN 2 (+) Primary DTS commands
CAN 2 (-) Primary DTS commands
Tach Signal (analog)
Analog Trim Signal
Analog Temp Signal
NOTE: It takes both sides of a given CAN circuit in order for it to function.
Both the BLU and WHT must have continuity and no shorts for the CAN 1 circuit to work (except for termination resistors)
Both the BRN and YEL must have continuity and no shorts for the CAN 2 circuit to work (except for termination resistors)
NOTE:
CAN 3 will be Vessel System.
CAN 2 is ONLY Digital Throttle and Shift.
CAN 1 is gauges and backup for DTS commands.
Scan tools talk thru CAN 1 only.
If CAN 1 is down, then the CDS and the system view can not show any faults or data.
NOTE:
DTS trim commands are sent digitally thru the CAN 2 circuit. They are NOT sent thru the GRN/WHT
and LT-BLU/WHT leads in the 14-pin Boat harness.
Page 3 of 3
10/20/2004
ETC, ESC and Boost Valve Pinouts
ETC (Electric Throttle Control)
Connector Function
1
TPS-1 Signal
2
Power 1 (5vdc)
3
Motor "B"
4
TPS-2 Signal
5
Motor "A"
6
Sensor Ground
All DTS OB
Color
LT-BLU/WHT
PPL/YEL
RED/BLU
WHT/YEL
RED/BLK
BLK/ORN
MerCruiser DTS
(MY 03) Color
DK-BLU/ORN
GRY
PPL/WHT
BLK/LT-BLU
BLU/WHT
BLK/PNK
MerCruiser DTS
(MY 04) Color
DK-BLU/ORN
GRY
PPL/WHT
BLK/BLU
BLU/WHT
BLK/PNK
ESC (Electric Shift Control)
Connector Function
A
Power 1 (5vdc)
B
Shift Position Signal
C
Sensor Ground
D
Motor "B"
E
Motor "A"
All DTS OB
Color
PPL/YEL
GRN
BLK/ORN
BLK
RED
MerCruiser DTS
Color (all years)
GRY
BLU/GRN
BLK/PNK
YEL/GRN
YEL/RED
Color-ESC Side
PPL/YEL
GRN
BLK/ORN
BLK
RED
MerCruiser DTS
(MY 05) Color
BLU/PNK
GRY
PPL/WHT
BLK/BLU
LT-BLU/WHT
BLK/PNK
Note: ETC and ESC motors are 2 wire permanent magnet electrical motors, just like the trim motor on an OB.
The PCM changes polarity on these 2 wires to reverse the direction of the motor as needed.
Neither wire is really positive or negative, it depends on which way you are trying to run the motor.
Both wires must have continuity and not be shorted to ground or any other wire in order for these motors to work.
Excessive current flow in the ETC Motor A and B circuit will cause an "ETC Sticking" fault.
An Open circuit in the ETC Motor A and B circuit will cause an "ETC Loss of Control" fault.
Corrosion/Oxidiation on the ETC connector can cause the "ETC Sticking" fault.
Boost Valve (Verado/Family 3)
Pin
Function
1
Ground
2
Power (12vdc)
3
Bypass Valve Control
4
Bypass Valve Status
Color Code
BLK
RED/ORN
BLU/YEL
LT-BLU
to PCM C-9
to PCM B-16
10/20/2004
System View Pinouts
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
System View
Service Function
Horn
Main Power Relay
Station Active LED
Port Neutral LED
STBD Neutral LED
Throttle Only LED
CAN 2 (+)
CAN 2 (-)
Battery (12v)
Wake up (Key Switch B+)
Not Used
Auxiliary Potentiometer 4
Auxiliary Potentiometer 6
Track Pad Up
Track Pad Left
Ground
LED Power (12V)
Sensor Power (5V)
HiResolution Pot Signal
Aux Potentionmeter 1
Aux Potentionmeter 5
Pitch Sensor
Track Pad Down
Track Pad Right
Service Function
Increasing Pot Signal
Not Used
Decreasing Pot Signal
Not Used
Aux Potentiometer 2
Aux Potentiometer 3
Roll Sensor
Emergency Stop Input
Sensor Ground
Start Signal Input (Port)
Not Used
Stbd Trim Down Input
System Link Signal (Stbd_
NMEA 0183 (+)
CAN 1 (+)
Ambient Temp Sensor
Track Pad Enter
Start Signal Input (Stbd)
Not Used
Stbd Trim Up Input
Neutral Switch
System Link Signal (Port)
NMEA 0183 (-)
CAN 1 (-)
Display only
ColorCode
TAN/BLU
PPL/WHT
*
*
*
*
*
*
RED
PPL
*
*
*
*
*
BLK
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
BLK/ORN
*
*
*
YEL/PPL
WHT/LT.BLU
WHT
TAN
*
*
*
*
*
YEL/WHT
BLU/WHT
BLU
*Not Used
03 DTS
Color Code
TAN/BLU
RED/BLK
GRAY
WHT/YEL
ORN
TAN/GRN
YEL
BRN
RED
PPL
*
GRN/ORN
GRN/YEL
WHT/RED
WHT/ORN
BLK
WHT/PPL
PPL/YEL
BLU/YEL
PNK
GRN/RED
GRN/PPL
WHT/BLU
WHT/BRN
Color Code
PNK/PPL
*
PNK/RED
*
GRN/BLU
GRN/BLK
GRN/PPL
BLK/YEL
BLK/ORN
YEL/GRN
*
GRN/WHT
YEL/PPL
WHT/LT.BLU
WHT
TAN
WHT/GRY
YEL/RED
*
LT.BLU/WHT
YEL/BLK
*
BLU/WHT
BLU
*Not Used
Note:
10/20/2004
For MY03 DTS, the system view is also the DTS Command Module
For MY04 and MY05 DTS, the system view is a "display only" device and does not control throttle and shift.
ThunderBolt V - MerCruiser Pinouts
Requires DDT Adaptor Harness (84-861540A1)
Thunderbolt V
Layout:
Looking into
the connector
with the tab up
Left to Right
1 thru 8
95-97
1
2
3
4
5
6
7
8
Scan Data is thru
2 external tabs.
Thunderbolt V
Layout:
AC EGIK
BD FHJL
Looking into
connector with
the tab up
98 & up
A
B
C
D
E
F
G
H
I
J
K
L
Color
BLK
Empty#
PPL/WHT
WHT/GRN
WHT/RED
PPL
BLK
GRY
Function
Shift Int.*
Warning Horn
Knock/Timing
Timing Signal
Sensor Power
Key B+
Ground
Ignition Coil Driver
# TAN/BLU
on some
drawings
*Alpha Shift Interrupt (normally open)
*Bravo must be grounded to run normally
Color
#
#
PPL
TAN/BLU
WHT/BLK
PPL/WHT
WHT/GRN
YEL
WHT/RED
BLK
-------------GRY
Function
Scan Tool Data
Scan Tool Data
Key Switch B+
Warning Horn
Shift Int.*
Knock/Timing
Timing Signal
ECT
Sensor Power
Ground
Empty
Ignition Coil Driver
#Pins A & B are only used
by the DDT harness
Knock Modules
A
B
C
D
E
Color
Empty
PPL
PPL/WHT
BLK
BLU
*Alpha Shift Interrupt (normally open)
*Bravo must be grounded to run normally
Function
Key B+
Knock Retard Out to ignition module
Ground
Knock Signal In from sensor
10/20/2004
High-Performance HP525EFI
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
PCM03 HP525EFI
Wakeup (Key-Switch B+)
Empty
MAP Signal
Oil Pressure Signal
Pitot Signal
TP1 Signal
Empty
Fuel Pressure Signal
Tab Position Signal
Tab Position Signal
CAN1 (+)
Steering Angle Signal
Empty
MAT Signal
ECT Signal
Oil Temp Signal
Empty
Scan Tool (-)
Knock 1 (-)
Knock 2 (-)
CAN 1 (-)
Sender Ground
Power 1 (5vdc)
SeaPump Signal
Fuel Level 2 Signal
Fuel Level 1 Signal
Trim Position (smartcraft)
Scan Tool (+)
Knock 1 (+)
Knock 2 (+)
Empty
Empty
Color
PPL
Empty
YEL
LT-BLU/RED
WHT/ORN
LT-BLU/WHT
Empty
PNK/RED
DK-BLU
BLU/YEL
WHT
GRY/RED
Empty
TAN
TAN/WHT
BLU/YEL
Empty
WHT/BLU
BLK/RED
BLK/WHT
BLU
BLK/ORN
PPL/YEL
WHT/YEL
YEL/PNK
YEL/RED
BRN
DK-BLU/WHT
WHT/BLU
WHT/BLK
Empty
Empty
Page 1 of 3
High-Performance HP525EFI
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
Pin
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
PCM03 HP525EFI
Empty
EST Coil Pack #1&6 Trigger
Empty
MPR control
Crank Position Signal (-)
Cam Position Signal
IAC Valve control
Empty
Empty
EST Coil Pack #7&4 Trigger
Fuel Pump Relay Control
Tach Signal out
Crank Position Signal (+)
Empty
Gear Position Switch Signal
Lube Bottle Switch Input
MPR Output (to PCM)
MPR Output (to PCM)
Trim Up Relay Control
Fuel Injector #4 driver
Warning Horn driver
Fuel Injector #3 driver
E-Stop (thru CAN bus)
Empty
PCM03 HP525EFI
Empty
Empty
Fuel Injector #8 driver
Empty
Fuel Injector #7 driver
Fuel Injector #1 driver
EST Coil Pack #3&2 Trigger
EST Coil Pack #5&8 Trigger
Empty
Empty
Fuel Injector #2 driver
Empty
Empty
Empty
Ground
Ground
Empty
Empty
Empty
Empty
Fuel Injector #6 driver
Empty
Fuel Injector #5 driver
Ground
Color
Empty
GRN/BRN
Empty
YEL/PPL
WHT
WHT/BRN
WHT/PPL
Empty
Empty
GRN/RED
YEL/BLK
GRY
RED
Empty
BLK/RED
BLU/TAN
RED/BLU
RED/BLU
WHT/YEL
YEL/PNK
TAN/LT-BLU
ORN/PNK
BLK/YEL
Empty
Color
Empty
Empty
PNK/PPL
Empty
PNK/DK-BLU
BRN/PNK
GRN/RED
GRN/BLK
Empty
Empty
RED/PNK
Empty
Empty
Empty
BLK/WHT
BLK/WHT
Empty
Empty
Empty
Empty
PNK/PPL
Empty
DK-BLU/PNK
BLK/WHT
Page 2 of 3
High-Performance HP525EFI
Splices
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Function (HP525EFI)
Sender Ground
Wakeup
Fuel Pressure Signal
Fuel Injector Power
Fuel Injector Power
ECT Signal
Trim Position (Smartcraft)
Power 1 (5vdc)
Ground
Fuel Injector Power
Sender Ground
Sender Ground
MPR Output (to PCM)
Sender Ground
Power 1 (5vdc)
B+
MPR Output (to PCM)
MPR Output (to fuse block)
Ground
Solenoid Gnd (neutral switch)
B+ (fused)
MPR Output (to PCM)
Power 1 (5vdc)
B+ (fused)
Power 1 (5vdc)
Oil Temp Signal
EST Power (12vdc)
Oil Pressure Signal
Color
BLK/ORN
PPL
PNK/RED
RED/WHT
RED/WHT
TAN/WHT
BRN
PPL/YEL
BLK
RED/WHT
BLK/ORN
BLK/ORN
RED/BLU
BLK/ORN
PPL/YEL
RED
RED/BLU
RED/GRN
BLK
BLK/RED
RED/PPL
RED/BLU
PPL/YEL
RED/PPL
PPL/YEL
BLU/YEL
RED/YEL
LT-BLU/RED
10/20/2004
Page 3 of 3
High-Performance HP1075SCi Pinouts
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
PCM03 HP1075SCi
Wakeup (Key Switch B+)
Empty
MAP Signal
Oil Pressure Signal
Pitot Signal
TP1 Signal
Empty
Fuel Pressure Signal
StbdTab Position Signal
PortTab Position Signal
CAN1 (+)
Steering Angle Signal
Empty
MAT Signal
ECT Signal
Oil Temp Signal
Transmission Temperature
Scan Tool (-)
Knock 1 (-)
Knock 2 (-)
CAN 1 (-)
Sender Ground
Power 1 (engine sensors)
SeaPump Signal
Fuel Level 2 Signal
Fuel Level 1 Signal
Trim Position (smartcraft)
Scan Tool (+)
Knock 1 (+)
Knock 2 (+)
Empty
Empty
Color
PPL
Empty
YEL
LT-BLU/RED
WHT/ORN
LT-BLU/WHT
Empty
PNK/RED
GRN/RED
GRN
WHT
GRY/RED
Empty
TAN
TAN/WHT
BLU/YEL
ORN
WHT/BLU
BLK/RED
BLK/WHT
BLU
BLK/ORN
PPL/YEL
WHT/YEL
YEL/PNK
YEL/RED
BRN
DK-BLU/WHT
WHT/BLU
WHT/BLK
Empty
Empty
Page 1 of 3
High-Performance HP1075SCi Pinouts
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
Pin
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
PCM03 HP1075SCi
EST Return
EST Coil #1 Trigger
Boost Bypass Status
MPR control
Crank Position Signal (-)
Cam Position Signal
IAC Valve control
Empty
EST Coil # 5 Trigger
EST Coil #3 Trigger
Fuel Pump Relay Control
Tach Signal out
Crank Position Signal (+)
Empty
Gear Position Switch Signal
Empty
MPR Output (to PCM)
MPR Output (to PCM)
Empty
Fuel Injector #4 driver
Warning Horn driver
Fuel Injector #3 driver
E-Stop (thru CAN bus)
Power 2 (smartcraft sensors)
PCM03 HP1075SCi
Empty
Empty
Fuel Injector #8 driver
Empty
Fuel Injector #7 driver
Fuel Injector #1 driver
EST Coil #4 Trigger
EST Coil #2 Trigger
Boost Bypass Valve Control
Empty
Fuel Injector #2 driver
EST Coil #6 Trigger
EST Coil #7 Trigger
EST Coil #8 Trigger
Ground
Ground
Empty
Empty
Empty
Empty
Fuel Injector #6 driver
Empty
Fuel Injector #5 driver
Ground
Color
BLK/GRN
GRN/BRN
LT-BLU
YEL/PPL
WHT
RED/WHT
WHT/BLU
Empty
GRN/DK-BLU
BRN/ORN
YEL/BLK
GRY
RED
Empty
BLK/RED
Empty
RED/BLU
RED/BLU
Empty
PNK/YEL
TAN/LT-BLU
PNK/ORN
BLK/YEL
PPL/BLK
Color
Empty
Empty
PNK
Empty
PNK/PPL
PNK/BRN
GRN/YEL
GRN/RED
BLU/YEL
Empty
PNK/RED
GRN/BLK
GRN/WHT
GRN
BLK/WHT
BLK/WHT
Empty
Empty
Empty
Empty
PNK/BLK
Empty
PNK/DK-BLU
BLK/WHT
Page 2 of 3
High-Performance HP1075SCi Pinouts
Splices
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Function (HP1075SCi)
Key-switch B+ (wake)
Oil Pressure Signal
Fuel Injector #2 Signal
ECT Signal
Sender Ground
Sender Ground
Sender Ground
Power 1
Trim Position (smartcraft)
Power 1
B+
B+
MPR Output (to fuse block)
MPR Output (to PCM)
MPR Control
B+ Fused
Ground
CAN 1 (+)
CAN 1 (-)
EST Return
EST Return
Ground
Ground
PCM Ground
PCM Ground
EST Power (12v)
EST Power (12v)
EST Power (12v)
IAC Valve control
Fuel Injector #4 Signal
Fuel Injector Power
Fuel Injector Power
Fuel Injector Power
Fuel Injector Power
Fuel Injector #3 Signal
Fuel Injector #8 Signal
Fuel Injector #7 Signal
Fuel Injector #1 Signal
Fuel Injector #2 Signal
Fuel Injector #6 Signal
Fuel Injector #5 Signal
Solenoid Gnd (neutral switch)
MPR Output (to PCM)
Power 2
Ground
???
MPR Output (to PCM)
Sender Ground
Color
PPL
LT-BLU/RED
PNK/RED
TAN/WHT
BLK/ORN
BLK/ORN
BLK/ORN
PPL/YEL
BRN
PPL/YEL
RED
RED
RED/GRN
RED/BLU
YEL/PPL
RED/PPL
BLK
WHT
DK-BLU
BLK/GRN
BLK/GRN
BLK
BLK
BLK/WHT
BLK/WHT
RED/YEL
RED/YEL
RED/YEL
WHT/BLU
PNK/YEL
RED/WHT
RED/WHT
RED/WHT
RED/WHT
PNK/ORN
PNK
PNK/PPL
PNK/BRN
PNK/RED
PNK/BLK
PNK/DK-BLU
BLK/RED
RED/BLU
PPL/BLK
BLK
BLU/YEL
RED/BLU
BLK/ORN
10/20/2004
Page 3 of 3
GENERAL INFORMATION
4
MerCruiser EFI III (1004)
Table of Contents
Page
Fuel Recommendations . . . . . . . . . . . . . . . . . .
4-1
Fuel Delivery System . . . . . . . . . . . . . . . . . . . .
4-3
Battery Requirements for MerCruiser
Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7
Battery Ratings . . . . . . . . . . . . . . . . . . . . .
4-7
Cold Cranking Amps – (CCA) . . . . . . . . .
4-7
Marine Cranking Amps – (MCA) . . . . . . .
4-7
Reserve Capacity . . . . . . . . . . . . . . . . . . .
4-7
Amp-Hour Rating . . . . . . . . . . . . . . . . . . . .
4-7
Battery Cables - Length and Size . . . . . . . . .
4-9
Battery Testing . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Hydrometer Tests . . . . . . . . . . . . . . . . . . . 4-10
Capacity Tests . . . . . . . . . . . . . . . . . . . . . . 4-10
Charging Guide . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
12 Volt Battery Recommended Rate* and
Time for Fully Discharged Condition . 4-11
Wiring Colors for MerCruiser . . . . . . . . . . . . . . 4-12
Wiring Harness Service . . . . . . . . . . . . . . . . . . 4-13
Wire Repair . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Wiring Connector Service . . . . . . . . . . . . . . . . 4-14
4-i - GENERAL INFORMATION
MerCruiser EFI III (1004)
Fuel Recommendations
IMPORTANT: Use of improper gasoline can damage your engine seriously. Engine damage resulting
from use of improper gasoline is considered misuse of engine, and damage caused thereby will not be
covered under the limited warranty.
FUEL RATINGS
USA and Canada - MerCruiser engines (with the exception of the early Black Scorpions [specified below]) in
the USA and Canada will operate satisfactorily when using a major brand of unleaded gasoline having a
MINIMUM pump posted Octane Rating of 87 AKI (anti knock index), which is the average of the RON (research
octane number) and the MON (motor octane number).
Federal regulations mandate that you DO NOT use leaded gasoline in the USA and Canada.
Higher octane fuels can be used on all models with the exception of early EFI models. On early EFI models refer
to Service Bulletin 94-12. If these engines are equipped with the original ECM, 87 AKI fuel must be used and
higher octane fuels must NOT be used.
Early Black Scorpions – Black Scorpions with serial number 0L0058999 and below must use fuel with a 91
AKI minimum. Black Scorpions with serial number 0L0059000 and above can use fuel with a 87 AKI minimum.
Outside USA and Canada - MerCruiser engines (with the exception of the early Black Scorpions [specified
below]) outside the USA and Canada will operate satisfactorily when using a major brand of unleaded gasoline
having a MINIMUM research octane number (RON) of 90. The use of leaded gasoline is acceptable unless
prohibited by government regulations.
Higher octane fuels can be used on all models with the exception of early EFI models. On early EFI models refer
to Service Bulletin 94-12. If these engines are equipped with the original ECM, 90 RON fuel must be used and
higher octane fuels must NOT be used.
Early Black Scorpions – Black Scorpions with serial number 0L0058999 and below must use fuel with a 98
RON minimum. Black Scorpions with serial number 0L0059000 and above can use fuel with a 90 RON minimum.
USING REFORMULATED (OXYGENATED) GASOLINES (USA ONLY)
This type of gasoline is required in certain areas of the USA. The two types of “oxygenates” used in these fuels
is Alcohol (Ethanol) or Ether (MTBE or ETBE). If Ethanol is the “oxygenate” that is used in the gasoline in your
area, refer to “Gasolines Containing Alcohol.”
These “Reformulated Gasolines” are acceptable for use in your MerCruiser engine.
MerCruiser EFI III (1004)
GENERAL INFORMATION - 4-1
GASOLINES CONTAINING ALCOHOL
If the gasoline in your area contains either “methanol” (methyl alcohol) or “ethanol” (ethyl alcohol), you should
be aware of certain adverse effects that can occur. These adverse effects are more severe with “methanol.” Increasing the percentage of alcohol in the fuel can also worsen these adverse effects.
Some of these adverse effects are caused because the alcohol in the gasoline can absorb moisture from the
air, resulting in a separation of the water/alcohol from the gasoline in the fuel tank.
The fuel system components on your MerCruiser engine will withstand up to 10% alcohol content in the gasoline.
We do not know what percentage your boat’s fuel system will withstand. Contact your boat manufacturer for specific recommendations on the boats fuel system components (fuel tanks, fuel lines, and fittings). Be aware that
gasolines containing alcohol may cause increased:
• Corrosion of metal parts.
• Deterioration of rubber or plastic parts.
• Fuel permeation through rubber fuel lines.
• Starting and operating difficulties.
! WARNING
FIRE AND EXPLOSION HAZARD: Fuel leakage from any part of fuel system can be a fire and explosion
hazard which can cause serious bodily injury or death. Careful periodic inspection of entire fuel system
is mandatory, particularly after storage. All fuel components including fuel tanks, whether plastic metal
or fiberglass, fuel lines, fittings, fuel filters and carburetors/fuel injection components should be inspected for leakage, softening, hardening, swelling or corrosion. Any sign of leakage or deterioration
requires replacement before further engine operation.
Because of possible adverse effects of alcohol in gasoline, it is recommended that only alcohol-free gasoline
be used where possible. If only fuel containing alcohol is available, or if the presence of alcohol is unknown, increased inspection frequency for leaks and abnormalities is required.
IMPORTANT: When operating a MerCruiser engine on gasoline containing alcohol, storage of gasoline
in the fuel tank for long periods should be avoided. Long periods of storage, common to boats, create
unique problems. In cars alcohol-blend fuels normally are consumed before they can absorb enough
moisture to cause trouble, but boats often sit idle long enough for phase separation to take place. In
addition, internal corrosion may take place during storage if alcohol has washed protective oil films from
internal components.
4-2 - GENERAL INFORMATION
MerCruiser EFI III (1004)
Fuel Delivery System
! WARNING
Boating standards (NMMA, ABYC, etc.) and Coast Guard regulations must be adhered to when
constructing the engine compartment.
GENERAL
The main concern of a boat’s fuel system is safety; this must be achieved through a technically sound installation
and constant inspection.
The fuel system, from the filler pipe to the fuel pump, is the same in principle for all boats.
The fuel tank is an integrated component of the boat. Refer to the special information on service and maintenance, which you have received from the tank manufacturer.
Only a few points related to function and safety are listed here [Refer to boating standards (NMMA, ABYC, etc.)
and Coast Guard regulations for complete guidelines]:
• All connections should be on the upper side of the tank.
• The drain plug at the lowest point on the tank serves to permit the removal of water and sediment.
• The filler pipe outer diameter should be at least 2 in. (50 mm).
• The tank breather pipe must have an inner diameter of at least 1/2 in. (13 mm) and must be fitted with a swan
neck to prevent water from entering the tank.
It is recommended that the exact route and length of the fuel lines be established at the first installation of the
engine to prevent problems later in connecting them to the engine.
All fuel lines must be well secured. The holes where the lines run through the bulkheads should be carefully
rounded off or protected with rubber grommets. This prevents damage to the lines from abrasion.
The following, but not limited to the following, additional fuel connection related points, applying to all engines
unless otherwise stated, must be considered [Refer to boating standards (NMMA, ABYC, etc.) and Coast Guard
regulations for complete guidelines]:
1. On Gasoline Engines: Fuel tank should be mounted below carburetor level (if possible) or gravity feed may
cause carburetor fuel inlet needle to unseat and flooding may result.
2. Fuel pickup should be at least 1 in. (25 mm) from the bottom of fuel tank to prevent picking up impurities.
3. On Gasoline Engines: The maximum measured vacuum at the engine’s fuel inlet must not exceed 2 in. Hg
or 1 psi (6.9 kPa) at 600, 3000, full throttle rpm, and idle rpm.
IMPORTANT: Vacuum reading higher than specified can cause vapor locking with some of today’s fuels.
It can also cause poor engine performance because of fuel starvation.
4. On Gasoline Engines: Fuel lines used must be Coast Guard approved (USCG Type A1).
Diameter of fittings and lines must not be smaller than 5/16 in. (8 mm) ID on 262 CID/4.3L and 305 CID/5.0L
and 350 CID/5.7L engines.
Diameter of fittings and lines must not be smaller than 3/8 in. (10 mm) I.D. on 377 CID/6.2L, 454 CID/7.4L and
502 CID/8.2L engines.
5. On Multi-Engine Gasoline Installations: It is best to use a fuel pickup and supply line for each engine. If
a single pickup and line is used, line must not be smaller than 1/2 in. (13mm) I.D.
6. Larger diameter (than previously specified) lines and fittings must be used on installations requiring long lines
or numerous fittings.
7. Fuel line(s) should be installed free of stress and firmly secured to prevent vibration and/or chafing.
MerCruiser EFI III (1004)
GENERAL INFORMATION - 4-3
8. Sharp bends in fuel lines should be avoided.
9. A flexible fuel line must be used to connect fuel supply line to fuel inlet fitting on engine to absorb deflection
when engine is running.
SPECIAL INFORMATION ABOUT ELECTRIC FUEL PUMPS
! CAUTION
The electric fuel pump and factory installed water separating fuel filter have been carefully designed to
function properly together. Do not install additional fuel filters and/or water separating fuel filters between fuel tank and engine.
The installation of additional filters may cause:
• Fuel Vapor Locking
• Difficult Warm-Starting
• Piston Detonation Due to Lean Fuel Mixture
• Poor Driveability
SPECIAL INFORMATION FOR ALL GASOLINE ENGINES
! WARNING
Avoid gasoline fire or explosion. Gasoline is extremely flammable and highly explosive under certain
conditions. NEVER use gasoline as a cleaning solvent.
IMPORTANT: The following information is provided to ensure proper installation of brass fittings or
plugs installed into fuel pump or fuel filter base:
• Use #592 Loctite Pipe Sealant with Teflon on threads of brass fittings or plugs. DO NOT USE TEFLON
TAPE.
• Brass fittings or plugs should first be threaded into fuel pump or fuel filter base until finger tight.
• Fittings or plugs should then be tighten an additional 1-3/4 to 2-1/4 turns using a wrench. DO NOT
OVERTIGHTEN.
• To prevent over-tightening when installing a fuel line, the brass fittings should be held with a suitable
wrench as fuel line connectors are tightened securely.
4-4 - GENERAL INFORMATION
MerCruiser EFI III (1004)
MerCruiser EFI III (1004)
GENERAL INFORMATION - 4-5
4-6 - GENERAL INFORMATION
MerCruiser EFI III (1004)
Battery Requirements for MerCruiser Products
Battery Ratings
There are two major rating systems used in the USA for marine engine cranking batteries.
The most common is cca (cold cranking amps) which rates the cranking amps at 0° F. The
second system, mca (marine cranking amps), rates the cranking amps at 32° F. The mca
(marine cranking amps) rating of a given battery is always higher than the cca (cold cranking
amps) rating. There is a third rating system that some discount stores use which rates the
cranking amps of a battery at 80° F. The advertised cranking amps of these batteries is high
while the actual cca of it is very low.
Cold Cranking Amps – (CCA)
This figure represents in amps the current flow the battery can deliver for 30 seconds at 0º
Fahrenheit without dropping below 1.2 volts per cell (7.2 volts on a standard 12 volt battery).
The higher the number, the more amps it can deliver to crank the engine. (CCA x 1.3 = MCA)
Marine Cranking Amps – (MCA)
This figure is similar to the CCA test figure except that the test is run at 32º Fahrenheit instead
of “0”. (MCA x .77 = CCA)
This is more in line with actual boat operating conditions.
Reserve Capacity
This figure represents the time in minutes that a fully charged battery at 80º Fahrenheit can
deliver 25 amps, without dropping below 1.75 volts per cell (10.5 volts on a standard 12 volt
battery). The reserve capacity rating defines the length of time that a typical vehicle can be
driven after the charging system fails. The 25 amp figure takes into account the power
required by the ignition, lighting and other accessories. The higher the reserve capacity
rating, the longer the vehicle could be driven after a charging system failure.
Amp-Hour Rating
The ampere hour rating method is also called the 20 hour rating method. This rating represents the steady current flow that the battery will deliver for 20 hours while at 80º Fahrenheit
without dropping below 1.75 volts per cell (10.5 volts on a standard 12 volt battery). The rating
is actually the steady current flow times the 20 hours. Example: A 60 amp-hour battery will
deliver 3 amps continuously for 20 hours.
MerCruiser EFI III (1004)
GENERAL INFORMATION - 4-7
The following battery charts list the minimum cca, mca and Ah (Amp hour) ratings required
for use on MerCruiser products. The Amp hour rating is used outside the USA and Canada.
GASOLINE ENGINES
Engine
CID (L)
Minimum Required
Cranking Battery Size
4
4
V6
6
V8
V8
V8 Carb
V8
153 (2.5)
181 (3.0)
229 (3.8)
250 (4.0)
302 (5.0)
305 (5.0)
350 (5.7)
351 (5.8)
375 cca or
475 mca or
90 Ah
4
V6
V8
V8 Carb
224 (3.7)
262 (4.3)
427 (7.0)
454 (7.4)
450 cca or
575 mca or
90 Ah
V8
V8 Carb
V8
482 (7.9)
502 (8.2)
540 (8.9)
550 cca or
700 mca or
120 Ah
V8 Carb
572 (9.4)
600 cca or 750 mca
or 150 Ah
All EFI and MPI
Models
750 cca or 950 mca
or 180 Ah
DIESEL ENGINES
4-8 - GENERAL INFORMATION
Engine
CID (L)
Minimum Required
Cranking Battery Size
4
4
5
6
6
V8
103 (1.7)
169 (2.8)
183 (3.0)
219 (3.6)
254 (4.2)
444 (7.3)
750 cca or
950 mca or
180 Ah
MerCruiser EFI III (1004)
Battery Cables - Length and Size
NOTE: Battery should be located as close to engine as possible.
1. Select proper size positive (+) and negative (–) battery cables using the chart.
1. Add the positive and negative cable lengths together.
2. Divide by 2 to obtain the average cable length.
IMPORTANT: Terminals must be soldered to cable ends to ensure good electrical contact. Use electrical grade (resin flux) solder only. Do NOT use acid flux solder, as it may
cause corrosion and a subsequent failure.
IMPORTANT: Tapered post connectors with wing nut connections can be used. The
tapered posts must be used for the engine battery cables. The wing nut connections
should be used only for the power trim pump and accessories. It is recommended that
the wing nuts be replaced with regular nuts to ensure that the connections are
tightened securely.
GASOLINE ENGINES
Battery
Cable Length
Minimum
Cable Gauge
Up to 3-1/2 ft. (1.1 m)
4 (25mm2)
3-1/2 - 6 ft. (1.1 - 1.8 m)
2 (35mm2)
6 - 7-1/2 ft. (1.8 - 2.3 m)
1 (50mm2)
7-1/2 - 9-1/2 ft. (2.3 - 2.9 m)
0 (50mm2)
00 (70mm2)
9-1/2 - 12 ft. (2.9 - 3.7 m)
12 - 15 ft. (3.7 - 4.6 m)
000 (95mm2)
15 - 19 ft. (4.6 - 5.8 m)
0000 (120mm2)
DIESEL ENGINES
Battery
Cable Length
Minimum
Cable Gauge
Up to 3 ft. (0.9m)
•
2 (35mm2)
3 - 3-3/4 ft. (0.9 - 1.1m)
•
1 (50mm2)
3-3/4 - 4-3/4 ft. (1.1 - 1.4m)
•
0 (50mm2)
4-3/4 - 6 ft. (1.4 - 1.8m)
•
00 (70mm2)
6 - 7-1/2 ft. (1.8 - 2.3m)
• 000 (95mm2)
7-1/2 - 9-1/2 ft. (2.3 - 2.9m)
• 0000 (120mm2)
9-1/2 - 12 ft. (2.9 - 3.7m)
•
12 - 15 ft. (3.7 - 4.6m)
• 000 (95mm2)
15 - 19 ft. (4.6 - 5.8m)
• 0000 (120mm2)
00 (70mm2)
• Two cables of specified gauge required for positive and two required for negative.
MerCruiser EFI III (1004)
GENERAL INFORMATION - 4-9
With the old battery cable recommendation, the negative (–) and the positive (+) battery
cables were measured separately and then select the correct cable gauge to fit the length
measured for each. This was OK if they were both the same length. It did not work well if there
was a battery switch installed in the positive (+) battery cable between the engine and battery. Then, the positive (+) cable had to use a much larger gauge than the negative (–) did.
In the example below, this would have meant the shorter 36 in. (91.4 cm) length negative (–)
would have used a 4 (25mm2) gauge cable. The longer 228 in. (579.1 cm) positive (+) cable
would have used 0000 (120mm2) gauge.
EXAMPLE: A person measures 36 in. (91.4 cm) length of negative (–) cable between
engine and battery. They measure 108 in. (274.3 cm) of positive (+) cable between the
engine and the battery switch and 120 in. (304.8 cm) between the battery switch and
battery. Add 36 in. (91.4 cm) + 108 in. (274.3 cm) + 120 in. (304.8 cm) = 264 in. (670.5 cm)
divide by 2 = 132 in. (335.3 cm) or 11 ft. (3.4 m). So BOTH the negative (–) AND positive (+)
battery cable use the 00 (70mm2) gauge cable.
By using the same gauge battery cable, 00 (70mm2) gauge in the example above, for BOTH
the negative (–) and positive (+) cable, the longer length positive (+) cable can use a smaller
gauge cable than it would have if the negative (–) and positive (+) gauges were sized to their
respective lengths.
Battery Testing
Hydrometer Tests:
A fully charged battery will read between 1.225 and 1.280 at 80º Fahrenheit. Readings of
1.225 and lower will require recharging & retesting. All cells should read within 30 points of
each other. You must correct the Hydrometer reading for Ambient Temperature.
Capacity Tests:
(The Specific Gravity must be 1.225 or higher before continuing)
Variable Load High Rate Discharge Tester (Recommended): Discharge the battery with a
load bank (carbon pile) set to 1/2 the CCA Rating or 3 times the Amp–Hour Rating for 15
Seconds, at the end of the 15 second period the battery voltage must be 9.6 volts or higher*.
Fixed Resistance: This equipment has built–in load for high–rate discharge testing. Follow
equipment manufacturer’s instructions regarding test period and meter readings.
Cranking Discharge Method: With a Voltmeter attached to the battery, Crank the engine for
15 seconds, the battery voltage must be 9.6 Volts or higher* at the end of the 15 second
period.
* Lower ambient temperature readings (below 70º Fahrenheit) will result in lower voltage
readings.
4-10 - GENERAL INFORMATION
0ºF
10ºF
20ºF
30ºF
40ºF
50ºF
60ºF
8.5v
8.7v
8.9v
9.1v
9.3v
9.4v
9.5v
MerCruiser EFI III (1004)
Charging Guide
12 Volt Battery Recommended Rate* and Time for Fully Discharged Condition
Twenty Hour
Rating
5
Amperes
10
Amperes
20
Amperes
30
Amperes
50
Ampere-Hours or
less
10 Hours
5 Hours
2-1/2
Hours
2 Hours
Above 50 to 75
Ampere-Hours
15 Hours
7-1/2
Hours
3-1/2
Hours
Above 75 to 100
Ampere-Hours
20 Hours
10 Hours
Above 100 to
150
Ampere-Hours
30 Hours
Above 150
Ampere-Hours
40
Amperes
50
Amperes
2-1/2
Hours
2 Hours
1-1/2
Hours
5 Hours
3 Hours
2-1/2
Hours
2 Hours
15 Hours
7-1/2
Hours
5 Hours
3-1/2
Hours
3 Hours
20 Hours
10 Hours
6-1/2
Hours
5 Hours
4 Hours
* Initial rate for constant voltage taper rate charger
To avoid damage, charging rate must be reduced or temporarily halted, if:
1. Electrolyte temperature exceeds 125° F (52° C).
2. Violent gassing or spewing of electrolyte occurs.
Battery is fully charged when, over a two hour period at a low charging rate in amperes, all
cells are gassing freely and no change in specific gravity occurs. For the most satisfactory
charging, the lower charging rates in amperes are recommended.
Full charge specific gravity is 1.260-1.280, corrected for temperature with electrolyte level at
split ring.
Battery Power as Affected by Temperature
100%
80°F
(27°C)
100%
165%
83%
32°F (0°C)
250%
61%
0°F
(-18°C)
45%
-20°F
(-29°C)
350%
74310
Power (Watts) Available
MerCruiser EFI III (1004)
Power (Watts) Required
GENERAL INFORMATION - 4-11
Wiring Colors for MerCruiser
NOTE: Color codes listed below DO NOT apply to fuel injection system harnesses.
NMMA COLOR CODE AND
ABBREVIATIONS
WHERE USED
BLACK (BLK)
All Grounds
BROWN (BRN)
Reference Electrode - MerCathode
LT. BLUE/WHITE (LT BLU/WHT)
Trim - “Up” Switch
GRAY (GRY)
Tachometer Signal
GREEN/WHITE (GRN/WHT)
Trim - “Down” Switch
TAN (TAN)
Water Temperature Sender to Gauge
LIGHT BLUE (LT BLU)
Oil Pressure Sender to Gauge
PINK (PNK)
Fuel Gauge Sender to Gauge
BROWN/WHITE (BRN/WHT)
Trim Sender to Trim Gauge
PURPLE/WHITE (PUR/WHT)
Trim - “Trailer” Switch
RED (RED)
Unprotected Wires from Battery
RED/PURPLE (RED/PUR)
Protected (Fused) Wires from Battery
RED/PURPLE (RED/PUR)
Protected (+12V) to Trim Panel
ORANGE (ORN)
Alternator Output / Anode Electrode - MerCathode
PURPLE/YELLOW (PUR/YEL)
Bypass-Ignition / Electric Fuel Pump*
PURPLE (PUR)
Ignition Switch (+12V)
YELLOW/RED (YEL/RED)
Starter Switch to Starter Solenoid to Neutral Start
Switch
TAN/BLUE (TAN/BLU)
Audio Warning System
* Also Electric Chokes on models so equipped
NOTE: Yellow used as GROUND wire in Europe and by some North American builders.
NOTES:
4-12 - GENERAL INFORMATION
MerCruiser EFI III (1004)
Wiring Harness Service
Marine engine control circuits contain many special design features not found in standard
land vehicle wiring. Environmental protection is used extensively to protect electrical contacts
and proper splicing methods must be used.
The proper operation of low amperage input/output circuits depends upon good continuity between circuit connectors. Before component replacement and/or during normal troubleshooting procedures, visually inspect any questionable mating connector. Mating surfaces should
be properly formed, clean and likely to make proper contact. Some typical causes of connector problems are listed below.
1. Improperly formed contacts and/or connector housing.
2. Damaged contacts or housing due to improper engagement.
3. Corrosion, sealer or other contaminants on the contact mating surfaces.
4. Incomplete mating of the connector halves during initial assembly or during subsequent
troubleshooting procedures.
5. Tendency for connectors to come apart due to vibration and/or temperature cycling.
6. Terminals not fully seated in the connector body.
7. Inadequate terminal crimps to the wire.
Wire harnesses should be replaced with proper part number harnesses. When signal wires
are spliced into a harness, use the same gauge wire with high temperature insulation only.
With the low current and voltage levels found in the system, it is important that the best possible bond be made at all wire splices by soldering the splices, as shown in the following illustrations. Use care when probing a connector or replacing connector terminals. It is possible
to short between opposite terminals. If this happens, certain components can be damaged.
Always use jumper wires with the corresponding mating terminals between connectors for
circuit checking. NEVER probe through connector seals, wire insulation, secondary ignition
wires, boots, nipples or covers.
Microscopic damage or holes will result in eventual water intrusion, corrosion and/or component or circuit failure.
Wire Repair
NOTE: Warranty repairs normally require the installation of a new harness.
1. Locate damaged wire.
2. Remove insulation as required.
73048
3. Splice two wires together using splice clips and rosin core solder.
73048
4. Cover splice with heat shrink sleeve to insulate from other wires.
73048
MerCruiser EFI III (1004)
GENERAL INFORMATION - 4-13
Wiring Connector Service
Most connectors in the engine compartment are protected against moisture and dirt that
could create oxidation and deposits on the terminals. This protection is important because
of the very low voltage and current levels found in the electronic system. The connectors have
a lock which secures the male and female terminals together. A secondary lock holds the seal
and terminal into the connector.
When diagnosing, open circuits are often difficult to locate by sight because oxidation or terminal misalignment are hidden by the connectors. Merely wiggling a connector on a sensor
or in the wiring harness may locate the open circuit condition. This should always be considered when an open circuit or failed sensor is indicated. Intermittent problems may also be
caused by oxidized or loose connections.
Before making a connector repair, be certain of the type of connector. Some connectors look
similar but are serviced differently. Replacement connectors and terminals are listed in the
Parts Catalog.
Ensure that the connector seals are not deformed or crushed when mating the connectors
together.
NOTES:
4-14 - GENERAL INFORMATION
MerCruiser EFI III (1004)
">