Advantech | AIMB-564 | User manual | Advantech AIMB-564 User manual

Advantech AIMB-564 User manual
AIMB-564
User Manual
Copyright Notice
The material in this document is the intellectual property of Advantech
Co, LTD. We take every care in the preparation of this document, but no
guarantee is given as to the correctness of its contents. Our products are
under continual improvement and we reserve the right to make changes
without notice.
Trademarks
Products and corporate names appearing in this manual may or may not
be registered trademarks or copyrights of their respective companies, and
are used only for identification or explanation and to the owners’ benefit,
without intent to infringe.
Part No. 2002056401 2nd. Edition
Printed in Taiwan
January 2008
AIMB-564 User Manual
ii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning! The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party
responsible for compliance could void the user’s
authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
iii
Safety Information
Electrical safety
•
•
•
•
•
•
To prevent electrical shock hazard, disconnect the power cable
from the electrical outlet before relocating the system.
When adding or removing devices to or from the system, ensure
that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables
from the existing system before you add a device.
Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.
Seek professional assistance before using an adapter or extension
cord. These devices could interrupt the grounding circuit.
Make sure that your power supply is set to the correct voltage in
your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
Operation safety
•
•
•
•
•
•
Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package.
Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any
damage, contact your dealer immediately.
To avoid short circuits, keep paper clips, screws, and staples away
from connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
Place the product on a stable surface.
If you encounter technical problems with the product, contact a
qualified service technician or your retailer.
AIMB-564 User Manual
iv
About this Guide
This user guide contains the information you need when installing and
configuring the motherboard.
How this guide is organized
This manual contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it supports. It also lists the hardware setup procedures that you
have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
•
Chapter 2: BIOS setup
This chapter tells how to change system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
•
Chapter 3: Software support
This chapter describes the contents of the support CD that comes with the
motherboard package.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1.
Advantech websites
For more information on this and other Advantech products, please visit
our website at:
http://www.advantech.com
For technical support and service, please visit our support website at:
http://www.advantech.com.tw/support/
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents
are not part of the standard package.
v
Typography
Bold text
Italics
<Key>
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
Keys enclosed in the less-than and greaterthan sign means that you must press the
enclosed key.
Example: <Enter> means that you must press
the Enter or Return key.
<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously, the key names are linked with a plus
sign (+).
Example: <Ctrl+Alt+D>
Command
Means that you must type the command
exactly as shown, then supply the required
item or value enclosed in brackets.
Example: At the DOS prompt, type the command line:
afudos /i[filename]
AIMB-564 User Manual
vi
AIMB-564 Specifications Summary
LGA775 socket for Intel® Quad-core / Core™ 2 Extreme/
Core™ 2 Duo / Pentium® D / Pentium® 4 / Celeron® D proCPU
cessor
Compatible with Intel® 05B/05A/06 processors Intel® HyperThreading Technology ready
Intel® Q965 / ICH8DO with Intel® Active Management TechChipset
nology
System Bus 1066 / 800 / 533 MHz
4 x DIMM, max. 8GB, DDR2 800 / 667 / 533 MHz, non-ECC,
Memory
un-buffered memory
Dual channel memory architecture
1 x PCI-E x16 slot
Expansion
1 x PCI-E x4 slot
Slots
2 x PCI slots
Intel® Graphics Media Accelerator 3000 (Intel® GMA 3000)
integrated
VGA
High Definition Video Processing with Max resolution to 2048
x 1536 bpp (@75Hz) Max. shared memory of 256MB
Support Microsoft® DX 9, OpenGL 1.4, Pixel Shader 2.0
Southbridge
- 6 x SATA 3.0 Gb/s ports
- Intel® Matrix Storage Technology supports RAID 0, 1, 5,
and 10
Storage
JMicron® JMB363 PATA and SATA controller
- 1 x UltraDMA 133/100/66/33 for up to 2 PATA devices
- 1 x Internal SATA 3.0 Gb/s port
- 1 x External SATA 3.0 Gb/s port (SATA On-the-Go)
LAN
Intel® 82566DM PCI-E Gigabit Ethernet Controller
ADI® AD 1988 8-channel High Definition Audio CODEC
- Support Jack-Sensing, Enumeration, Multi-streaming and
Audio
Jack-Retasking
- S/PDIF_OUT interface
TI®1394a controller supports 2 x IEEE 1394a ports (one at
IEEE 1394
midboard; one at back panel)
10 x USB 2.0 ports (6 ports at mid-board, 4 ports at back
USB
panel)
vii
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x Parallel port
1 x External Serial ATA port
Back Panel I/
1 x VGA port
O Ports
1 x IEEE 1394a connector
1 x RJ45 port
4 x USB 2.0/1.1 ports
8-channel Audio I/O ports
3 x USB 2.0 connectors support additional 6 USB ports
1 x Floppy disk drive connector
1 x IDE connector for two devices
1 x COM connector
1 x TPM connector
7 x Serial ATA connectors
1 x CPU Fan connector
2 x Chassis Fan connectors
Internal
1 x Power Fan connector
Connectors
1 x IEEE1394a connector
Front panel audio connector
1 x Azalia Digital Header
1 x S/PDIF Out Header Chassis intrusion connector CD audio
in
24-pin ATX Power connector
1 x 4-pin ATX 12 V Power connector
System panel connector
BIOS
16 Mb Flash ROM, AMI BIOS, PnP, DMI 2.0, WfM2.0, SM
Features
BIOS 2.3, ACPI 2.0a
ManageabilWfM 2.0, DMI 2.0, WOL by PME, WOR by PME, PXE, RPL
ity
Support CD Drivers
Contents
Advantech manual
Form
uATX form factor: 9.6” x 9.6” (24.4 cm x 24.4 cm)
Factor
*Specifications are subject to change without notice.
AIMB-564 User Manual
viii
Contents
Chapter
1 Product Information ........................................2
1.1
1.2
Welcome! .......................................................................... 2
Package Contents .............................................................. 2
1.3
Before you Proceed ........................................................... 3
Table
1.3.1
1.4
1.4.3
1.4.4
1.5.2
1.5.3
1.6.2
1.6.3
1.6.4
1.7.4
1.7.5
1.7.6
Installing an Expansion Card........................................ 23
Configuring an Expansion Card ................................... 23
Interrupt Assignments................................................... 24
Table 1.2 Standard Interrupt Assignments ............. 24
Table 1.3 IRQ Assignments for AIMB-564 ........... 24
PCI Slots ....................................................................... 26
PCI Express x4 Slot ...................................................... 26
PCI Express x16 Slot .................................................... 27
Jumper ............................................................................. 28
1.8.1
1.8.2
1.9
Overview....................................................................... 19
Figure 1.6 240-pin DDR2 DIMM socket................. 19
Memory Configuration ................................................. 20
Installing a DIMM ....................................................... 21
Removing a DIMM....................................................... 22
Expansion Slots ............................................................... 23
1.7.1
1.7.2
1.7.3
1.8
Installing the CPU......................................................... 10
Figure 1.4 AIMB-564 CPU socket 775 ................... 10
Installing the CPU Heatsink and Fan............................ 13
Figure 1.5 AIMB-564 CPU Fan Connector ............. 15
Uninstalling the CPU Heatsink and Fan ....................... 16
System Memory .............................................................. 19
1.6.1
1.7
Placement Direction........................................................ 5
Screw Holes .................................................................... 5
Figure 1.2 Screw holes............................................... 5
Motherboard Layout ....................................................... 6
Figure 1.3 Motherboard layout .................................. 6
Layout Contents.............................................................. 7
Central Processing Unit (CPU) ......................................... 9
1.5.1
1.6
Onboard LED.................................................................. 4
Figure 1.1 Onboard LED ........................................... 4
Motherboard Overview ..................................................... 5
1.4.1
1.4.2
1.5
1.1 Package Contents...................................... 2
Clear RTC RAM (CLRTC) .......................................... 28
Figure 1.7 Clear RTC RAM..................................... 29
Keyboard Power (3-pin KBPWR) ................................ 30
Figure 1.8 Keyboard Power Setting......................... 30
Connectors....................................................................... 31
ix
1.9.1
1.9.2
Chapter
Rear Panel Connectors.................................................. 31
Table 1.4 Activity/Link Speed LED....................... 31
Table 1.5 Audio 2, 4, 6, or 8-Channel Config ........ 32
Internal Connectors....................................................... 34
Figure 1.9 Floppy Disk Drive Connector................. 34
Figure 1.10 SPDIF OUT connector ........................... 34
Figure 1.11 AIMB-564 IDE connector ...................... 35
Figure 1.12 SATA connectors ................................... 36
Figure 1.13 IEEE 1394a Connector ........................... 37
Figure 1.14 SATA RAID connector .......................... 38
Figure 1.15 TPM connector ....................................... 39
Figure 1.16 USB 2.0 connectors ................................ 40
Figure 1.17 Internal Audio Connector ....................... 41
Figure 1.18 Fan connectors........................................ 41
Figure 1.19 Serial port connector............................... 42
Figure 1.20 Chassis Intrusion connector.................... 42
Figure 1.21 Front panel audio connector ................... 43
Figure 1.22 ATX Power connector ............................ 44
2 Award BIOS Setup.........................................48
2.1
Introduction ..................................................................... 48
2.1.1
2.1.2
BIOS Setup Program .................................................... 48
CMOS RAM Auto-backup and Restore ....................... 49
2.2
Entering Setup ................................................................. 50
2.3
Standard CMOS Setup .................................................... 51
Figure 2.1 Award BIOS Setup initial screen............ 50
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.3.7
2.4
Figure 2.2 Standard CMOS Features Screen ........... 51
Date............................................................................... 51
Time .............................................................................. 52
IDE Channel 0/1 Master/Slave ..................................... 52
Drive A / Drive B.......................................................... 52
Video............................................................................. 52
Halt On.......................................................................... 53
Memory......................................................................... 53
Advanced BIOS Features ................................................ 53
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.6
2.4.7
2.4.8
2.4.9
2.4.10
AIMB-564 User Manual
Figure 2.3 Advanced BIOS Features screen ............ 53
CPU Features ................................................................ 54
Hard Disk Boot Priority................................................ 54
Virus Warning............................................................... 54
CPU L1, L2 & L3 Cache .............................................. 54
Quick Power On Self Test ............................................ 54
First/Second/Third Boot Device ................................... 54
Boot Other Device ........................................................ 54
Swap Floppy Drive ....................................................... 55
Boot Up Floppy Seek.................................................... 55
Boot Up NumLock Status............................................. 55
x
2.4.11
2.4.12
2.4.13
2.4.14
2.4.15
2.4.17
2.4.18
2.5
Advanced Chipset Features............................................. 57
2.5.1
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
2.6
Figure 2.4 Advanced Chipset Features screen ......... 57
Memory Hole At 15M-16M ......................................... 57
Configure AMT BIOS Support (Intel® Active Management Technology) ......................................................... 58
PEG / Onchip VGA Control ......................................... 58
On-Chip Frame Buffer Size.......................................... 58
DVMT Mode ................................................................ 58
DVMT / FIXED Memory Size ..................................... 58
Integrated Peripherals...................................................... 59
2.6.1
2.6.2
2.6.3
2.6.4
2.6.5
2.6.6
2.6.7
2.6.8
2.6.9
2.6.10
2.6.11
2.6.12
2.6.13
2.6.14
2.6.15
2.6.16
2.6.17
2.6.18
2.6.19
2.6.20
2.7
Gate A20 Option........................................................... 55
Typematic Rate Setting................................................. 55
Typematic Rate (Chars/Sec) ......................................... 55
Typematic Delay (msec)............................................... 55
Security Option ............................................................. 55
MPS Version Control For OS....................................... 56
OS Select For DRAM > 64MB .................................... 56
Figure 2.5 Integrated peripherals ............................. 59
Figure 2.6 On-Chip IDE Device .............................. 59
On board Lan Boot ROM: ............................................ 59
IDE HDD Block Mode ................................................. 60
IDE DMA Transfer Access........................................... 60
On-Chip Primary / Secondary IDE Device................... 60
SATA Mode.................................................................. 60
Legacy Mode Support................................................... 60
Figure 2.7 USB device setting ................................. 61
USB 1.0 Controller ....................................................... 61
USB Operation Mode ................................................... 61
USB Storage Function: ................................................. 61
USB 2.0 Controller ....................................................... 61
USB Keyboard / Mouse Support .................................. 62
HD Audio Codec .......................................................... 62
Figure 2.9 Super I/O Device .................................... 63
Onboard FDC Controller .............................................. 63
Onboard Serial Port 1 ................................................... 63
Onboard Serial Port 2 ................................................... 63
Onboard Parallel Port.................................................... 63
Parallel Port Mode ........................................................ 64
EPP Mode Select .......................................................... 64
ECP Mode Use DMA ................................................... 64
PWRON After PWR-Fail ............................................. 64
Power Management Setup............................................... 65
2.7.1
2.7.2
Figure 2.10 Power management setup screen............ 65
ACPI Function .............................................................. 65
ACPI Suspend Type...................................................... 65
xi
2.7.3
2.7.4
2.7.5
2.7.6
2.7.7
2.7.8
2.7.9
2.7.10
2.7.11
2.7.12
2.7.13
2.7.14
2.7.15
2.7.16
2.8
PnP/PCI Configuration.................................................... 68
2.8.1
2.8.2
2.8.3
2.8.4
2.8.5
2.9
Run VGA BIOS if S3 Resume ..................................... 65
Power Management ...................................................... 66
Table 2.1 Power Saving.......................................... 66
Video Off Method......................................................... 66
Video Off In Suspend ................................................... 66
Suspend Type................................................................ 66
Suspend Mode............................................................... 66
HDD Power Down........................................................ 66
Soft-Off by PWR-BTTN .............................................. 67
PowerOn by Modem or Power On by Ring.................. 67
USB KB Wake Up From S3 ......................................... 67
PowerOn by Alarm or Resume by Alarm..................... 67
Wake-Up by PCI card................................................... 67
FDD, COM, LPT PORT ............................................... 67
PCI PIRQ [A-D]# ......................................................... 67
Figure 2.11 PnP/PCI configurations screen ............... 68
Init Display First ........................................................... 68
Reset Configuration Data.............................................. 68
Resources Controlled By .............................................. 68
PCI / VGA Palette Snoop ............................................. 68
Maximum Payload Size ................................................ 68
PC Health Status.............................................................. 69
Figure 2.12 PC Health Status Screen ......................... 69
System Temperature ..................................................... 69
CPU FAN Speed........................................................... 69
System FAN Speed....................................................... 69
VCORE and Other Voltages......................................... 69
Figure 2.13 Spread Spectrum Frequency/Voltage Control screen............................................. 70
2.10.1 CPU Clock Ratio Unlock.............................................. 70
2.10.2 CPU Clock Ratio .......................................................... 70
2.10.3 Spread Spectrum ........................................................... 70
2.9.1
2.9.2
2.9.3
2.9.4
2.11
TPM Support ................................................................... 71
Figure 2.14 Security Chip Configuration................... 71
2.11.1 TPM Support [Disabled]............................................... 71
2.11.2 TPM Status [No Change].............................................. 71
Figure 2.15 Security Chip Configuration................... 72
Figure 2.16 TPM POST Screen ................................. 72
2.12
2.13
2.14
Password Setting ............................................................. 73
Save & Exit Setup ........................................................... 74
Exit Without Saving ........................................................ 75
AIMB-564 User Manual
xii
CHAPTER
1
Product Introduction
This chapter describes the motherboard features and the new technologies it supports.
Chapter 1
Product Information
1.1 Welcome!
Thank you for buying an Advantech AIMB-564 motherboard!
The motherboard delivers a host of new features and latest technologies,
making it another standout in the long line of Advantech motherboards!
Before you start installing the motherboard, and hardware devices on it,
check the items in your package with the list below.
1.2 Package Contents
Check your motherboard package for the following items.
Table 1.1: Package Contents
Motherboard
Cables
Application CD
Documentation
Advantech AIMB-564
1 x Com cable
1 x Ultra DMA 133/100/66 cable
1 x Floppy disk drive cable
I/O shield
4 x SATA data cables
2 x SATA power cables
Advantech Driver CD
Startup manual
If any of the above items is damaged or missing, contact your retailer.
AIMB-564 User Manual
2
1.3 Before you Proceed
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Caution!
1. Unplug the power cord from the wall socket before
touching any component.
2. Use a grounded wrist strap or touch a safely
grounded object or a metal object, such as the
power supply case, before handling components to
avoid damaging them due to static electricity.
3. Hold components by the edges to avoid touching
the ICs on them.
4. Whenever you uninstall any component, place it on
a grounded antistatic pad or in the bag that came
with the component.
5. Before you install or remove any component,
ensure that the ATX power supply is switched off or
the power cord is detached from the power supply.
Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
3
Chapter 1 Product Information
1.3.1
Onboard LED
The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a
reminder that you should shut down the system and unplug the power
cable before removing or plugging in any motherboard component. The
illustration below shows the location of the onboard LED.
SB_PWR
ON
Standby
Power
Figure 1.1: Onboard LED
AIMB-564 User Manual
4
OFF
Powered
Off
1.4 Motherboard Overview
Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Warning! Make sure to unplug the power cord before installing
or removing the motherboard. Failure to do so can
cause you physical injury and damage motherboard
components.
1.4.1
Placement Direction
When installing the motherboard, make sure that you place it into the
chassis in the correct orientation. The edge with external ports goes to the
rear part of the chassis as indicated in the image below.
1.4.2
Screw Holes
Place eight screws into the holes indicated by circles to secure the motherboard to the chassis.
Caution!
Do not overtighten the screws! Doing so can damage
the motherboard.
Place this side towards
the rear of the chassis
Figure 1.2: Screw holes
5
Chapter 1 Product Information
1.4.3
Motherboard Layout
24.5cm (9.6in)
PWR_FAN
PS/2KBMS
T: Mouse
B: Keyboard
CHA_FAN
CPU_FAN
KBPWR
24.5cm (9.6in)
Intel
Q965
RTL8111B
EATXPWR
ATX12V
LAN_USB34
FLOPPY
USB12
DDR2 DIMM_B2 (64 bit,240-pin module)
VGA
DDR2 DIMM_B1 (64 bit,240-pin module)
PARALLE PORT
DDR2 DIMM_A1 (64 bit,240-pin module)
LGA775
DDR2 DIMM_A2 (64 bit,240-pin module)
Super I/O
ESATA
AUDIO
SATA_RAID1
PCIEX16
JMicron
JMB363
COM1
PCI1
CHA_FAN2
TPM_SLOT
TSB43AB22A
SB_PWR
CD
AD1988
PCIEX4_1
SATA1
Intel
ICH8
PCI2
CR2032 3V
Lithium Cell
CMOS Power
SATA3
SATA4
F_PANEL
PRI_EIDE
SPDIF_OUT
SATA2
AAFP
USB56
USB78
USB910 CLRTC CHASSIS
Figure 1.3: Motherboard layout
Note:
Refer to 1.9 Connectors for more information about rear panel
connectors and internal connectors.
AIMB-564 User Manual
6
1.4.4
Layout Contents
Slots
1.
2.
3.
4.
DDR2 DIMM slots
PCI slots
PCI Express x 4 slot
PCI Express x16 slot
Page
1-19
1-25
1-25
1-26
Clear RTC RAM (3-pin CLRTC)
Keyboard power (3-pin KBPWR)
Page
1-27
1-28
Rear panel connectors
1.
PS/2 mouse port (green)
2.
Parallel port
3.
IEEE 1394a port
4.
LAN (RJ-45) port
5.
Rear Speaker Out port (black)
6.
Center/Subwoofer port (orange)
7.
Line In port (light blue)
8.
Line Out port (lime)
9.
Microphone port (pink)
10.
Side Speaker Out port (gray)
11.
USB 2.0 ports 1 and 2
12.
USB 2.0 ports 3 and 4
13.
VGA port
14.
External SATA port
15.
PS/2 keyboard port (purple)
Page
1-29
1-29
1-29
1-29
1-30
1-30
1-30
1-30
1-30
1-30
1-31
1-31
1-31
1-31
1-31
Jumper
1.
2.
7
Chapter 1 Product Information
Internal connectors
1.
Floppy disk drive connector (34-1 pin FLOPPY)
2.
Digital Audio connector (4-1 pin SPDIF_OUT)
3.
IDE connector (40-1 pin PRI_IDE)
4.
ICH8DO Serial ATA connectors (7-pin SATA1
[red], SATA2 [red], SATA3 [red], SATA4 [red],
SATA5 [black], SATA6 [black])
5.
IEEE 1394a port connector (10-1 pin IE1394_2)
6.
JMicron® JMB363 Serial ATA RAID connector (7pin SATA_RAID1)
7.
TPM connector (20-1 pin TPM_SLOT)
8.
USB connectors (10-1 pin USB56, USB 78,
USB910)
9.
Optical drive audio connector (4-pin CD)
10.
CPU, chassis, and power fan connectors (4-pin
CPU_FAN, 3-pin CHA_FAN, 3-pin CHA_FAN2, 3pin PWR_FAN)
11.
Serial port connector (10-1 pin COM1)
12.
Chassis intrusion connector (4-1 pin CHASSIS)
13.
Front panel audio connector (10-1 pin AAFP)
14.
ATX power connectors (24-pin EATXPWR, 4-pin
EATX12V)
AIMB-564 User Manual
8
Page
1-32
1-32
1-33
1-34
1-35
1-36
1-37
1-38
1-39
1-39
1-40
1-40
1-41
1-42
1.5 Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed
for the Intel® Core™2 Extreme/Core™2 Duo/Pentium® D/Pentium® 4
and Celeron® D processors.
Note:
Caution!
1. Make sure the AC power is off before you install the CPU.
2. If installing a dual-core CPU, connect the chassis fan
cable to the CHA_FAN connector to ensure system stability.
1. Upon purchase of the motherboard, make sure that
the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any
damage to the PnP cap/socket contacts/motherboard components. We will bear the cost of repair
only if the damage is shipment/transit-related.
2. Keep the cap after installing the motherboard. We
will process Return Merchandise Authorization
(RMA) requests only if the motherboard comes
with the cap on the LGA775 socket.
3. The product warranty does not cover damage to
the socket contacts resulting from incorrect CPU
installation/removal, or misplacement/loss/ incorrect removal of the PnP cap.
9
Chapter 1 Product Information
1.5.1
Installing the CPU
To install a CPU:
Locate the CPU socket on the motherboard.
R
1.
Figure 1.4: AIMB-564 CPU socket 775
Note:
2.
Before installing the CPU, make sure that the cam box is
facing towards you and the load lever is on your left.
Press the load lever with your thumb (A), then move it to the left
(B) until it is released from the retention tab.
PnP Cap
Retention tab
A
Load lever
B
This side of the cam box
should face you.
Note:
To prevent damage to the socket pins, do not remove the
PnP cap unless you are installing a CPU.
AIMB-564 User Manual
10
3.
Lift the load lever in the direction of the arrow to a 135° angle.
4.
Lift the load plate with your thumb and forefinger to a 100° angle
(A), then push the PnP cap from the load plate window to remove
(B).
B
A
Load plate
11
Chapter 1 Product Information
5.
Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket, then fit the socket
alignment key into the CPU notch.
Alignment key
CPU notch
Gold triangle mark
Note:
6.
The CPU fits in only one correct orientation. DO NOT force
the CPU into the socket to prevent bending the connectors on
the socket and damaging the CPU!
Close the load plate (A), then push the load lever (B) until it snaps
into the retention tab.
A
B
AIMB-564 User Manual
12
7.
If installing a dual-core CPU, connect the chassis fan cable to the
CHA_FAN1 connector to ensure system stability.
Note:
1.5.2
The motherboard supports Intel® LGA775 processors with
Intel® Enhanced Memory 64 Technology (EM64T),
Enhanced Intel SpeedStep® Technology (EIST), and HyperThreading Technology.
Installing the CPU Heatsink and Fan
The Intel® LGA775 processor requires a specially designed heatsink and
fan assembly to ensure optimum thermal condition and performance.
Note:
1. When you buy a boxed Intel® processor, the package
includes the CPU fan and heatsink assembly. If you buy a
CPU separately, make sure that you use only an Intel®certified multi-directional heatsink and fan.
2. Your Intel® LGA775 heatsink and fan assembly comes
in a push-pin design and requires no tools to install.
3. If you purchased a separate CPU heatsink and fan
assembly, make sure that you have properly applied
Thermal Interface Material to the CPU heatsink or CPU
before you install the heatsink and fan assembly.
Note:
Make sure that you have installed the motherboard to the
chassis before you install the CPU fan and heatsink
assembly.
13
Chapter 1 Product Information
To install the CPU heatsink and fan:
1.
Place the heatsink on top of the installed CPU, making sure that the
four fasteners match the holes on the motherboard.
Motherboard hole
Fastener
Narrow end
of the groove
Note:
Orient the heatsink and fan assembly such that the CPU fan
cable is closest to the CPU fan connector.
Make sure to orient each fastener with the narrow end of the
groove pointing outward. (The photo shows the groove
shaded for emphasis.)
AIMB-564 User Manual
14
2.
Push down two fasteners at a time in a diagonal sequence to secure
the heatsink and fan assembly in place.
B
A
A
3.
A
B
B
A
B
Connect the CPU fan cable to the connector on the motherboard
labeled CPU_FAN.
R
GND
CPU FAN PWR
CPU FAN IN
CPU FAN PWM
CPU_FAN
Figure 1.5: AIMB-564 CPU Fan Connector
Note:
Do not forget to connect the CPU fan connector! Hardware
monitoring errors can occur if you fail to plug in this connector.
15
Chapter 1 Product Information
1.5.3
Uninstalling the CPU Heatsink and Fan
To uninstall the CPU heatsink and fan:
1.
Disconnect the CPU fan cable from the connector on the motherboard.
Rotate each fastener counterclockwise.
2.
3.
Pull up two fasteners at a time in a diagonal sequence to disengage
the heatsink and fan assembly from the motherboard.
B
A
A
B
A
B
B
A
AIMB-564 User Manual
16
4.
Carefully remove the heatsink and fan assembly from the motherboard.
5.
Rotate each fastener clockwise to ensure correct orientation when
reinstalling.
Note:
The narrow end of the groove should point outward after
resetting. (The photo shows the groove shaded for emphasis.)
17
Chapter 1 Product Information
Narrow end of the groove
Note:
Refer to the documentation in the boxed or stand-alone CPU
fan package for detailed information on CPU fan installation.
AIMB-564 User Manual
18
1.6 System Memory
1.6.1
Overview
The motherboard comes with four Double Data Rate 2 (DDR2) Dual
Inline Memory Modules (DIMM) sockets.
A DDR2 module has the same physical dimensions as a DDR DIMM but
has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2
DIMMs are notched differently to prevent installation on a DDR DIMM
socket.
DIMM_B2
DIMM_B1
DIMM_A2
DIMM_A1
128 Pins
R
112 Pins
The figure illustrates the location of the DDR2 DIMM sockets:
Figure 1.6: 240-pin DDR2 DIMM socket
Channel
Channel A
Channel B
Note:
Sockets
DIMM_A1 and DIMM_A2
DIMM_B1 and DIMM_B2
Install at least one memory module in DIMM_A1 or DIMM_A2
slot to support the Intel® Quiet System Technology and for
optimum performance. Otherwise, the system will halt.
19
Chapter 1 Product Information
1.6.2
Memory Configuration
You may install 256 MB, 512 MB, 1 GB, and 2 GB unbuffered non-ECC
DDR2 DIMMs into the DIMM sockets.
Note:
1. You may install varying memory sizes in Channel A and
Channel B. The system maps the total size of the lowersized channel for the dual-channel configuration. Any
excess memory from the higher-sized channel is then
mapped for single-channel operation.
2. Always install DIMMs with the same CAS latency. For
optimum compatibility, it is recommended that you obtain
memory modules from the same vendor.
3. If you install four 1GB memory modules or 2GB memory
modules, the system may only recognize 3GB or less
because the address space is reserved for other critical
functions. This limitation appears on Windows® XP 32-bit
operating systems which do not support Physical Address
Extension (PAE).
4. If you install a Windows® XP 32-bit operating system, a
total memory of less than 3GB is recommended.
5. This motherboard does not support memory modules
made up of 128 Mb chips or double sided x16 memory
modules.
AIMB-564 User Manual
20
Note:
1.6.3
Notes on memory limitations:
1. Due to chipset limitations, this motherboard can
only support up to 8 GB on the operating systems listed below. You may install a maximum
of 2 GB DIMMs on each slot, but only DDR2533 and DDR2-667 2 GB density modules are
available for this configuration.
2. Some old-version DDR2-800/667 DIMMs may
not match Intel®’s On-Die-Termination (ODT)
requirement and will automatically downgrade
to run at DDR2-533. If this happens, contact
your memory vendor to check the ODT value.
3. Due to chipset limitations, the DDR2-800 with
CL=4 will be downgraded to run at DDR2-667
by default. If you want to operate with lower
latency, adjust the memory timing manually.
4. Due to chipset limitations, the DDR2-667 with
CL=3 will be downgraded to run at DDR2-533
by default. If you want to operate with lower
latency, adjust the memory timing manually.
5. The total memory may have an 8MB reduction
under Single Channel mode, and a 16MB
reduction under Dual Channel mode because
the address space is reserved for the Intel®
vPro™ Technology and the Intel® Quiet System Technology.
Installing a DIMM
Caution!
Unplug the power supply before adding or removing
DIMMs or other system components. Failure to do so
can cause severe damage to both the motherboard
and the components.
21
Chapter 1 Product Information
To install a DIMM:
1. Unlock a DIMM socket by
pressing the retaining clips
outward.
2. Align a DIMM on the
socket such that the notch
on the DIMM matches the
break on the socket.
3. Firmly insert the DIMM
into the socket until the
retaining clips snap back in
place and the DIMM is
properly seated.
Note:
1.6.4
2
3
DDR2 DIMM notch
1
1
A DDR2 DIMM is keyed with a notch so that it fits in only one
direction. Do not force a DIMM into a socket to avoid damaging the DIMM.
The DDR2 DIMM sockets do not support DDR DIMMs. Do
not install DDR DIMMs to the DDR2 DIMM sockets.
Removing a DIMM
To remove a DIMM:
1. Simultaneously press the
retaining clips outward to
unlock the DIMM.
Note: Support the DIMM
lightly with your fingers when pressing
the retaining clips. The
DIMM might get damaged if it flips out with
extra force.
2. Remove the DIMM from
the socket.
AIMB-564 User Manual
2
1
1
22
DDR2 DIMM notch
1.7 Expansion Slots
In the future, you may need to install expansion cards. The following subsections describe the slots and the expansion cards that they support.
Warning! Make sure to unplug the power cord before adding or
removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard
components.
1.7.1
Installing an Expansion Card
To install an expansion card:
1.
2.
3.
4.
5.
6.
Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
Remove the system unit cover (if your motherboard is already
installed in a chassis).
Remove the bracket opposite the slot that you intend to use. Keep
the screw for later use.
Align the card connector with the slot and press firmly until the
card is completely seated on the slot.
Secure the card to the chassis with the screw you removed earlier.
Replace the system cover.
1.7.2
Configuring an Expansion Card
After installing the expansion card, configure it by adjusting the software
settings.
1.
2.
3.
Turn on the system and change the necessary BIOS settings, if any.
See Chapter 2 for information on BIOS setup.
Assign an IRQ to the card. Refer to the tables on the next page.
Install the software drivers for the expansion card.
Note:
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ
assignments. Otherwise, conflicts will arise between the two
PCI groups, making the system unstable and the card inoperable. Refer to the table on the next page for details.
23
Chapter 1 Product Information
1.7.3
Interrupt Assignments
Table 1.2: Standard Interrupt Assignments
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Priority
1
2
11
12
13
14
15
3
4
5
6
7
8
9
10
Standard function
System Timer
Keyboard Controller
Redirect to IRQ#9
IRQ holder for PCI steering*
Communications Port (COM1)*
IRQ holder for PCI steering*
Floppy Disk Controller
Printer Port (LPT1)*
System CMOS/Real Time Clock
IRQ holder for PCI steering*
IRQ holder for PCI steering*
IRQ holder for PCI steering*
PS/2 Compatible Mouse Port*
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
IRQ assignments for this motherboard
Table 1.3: IRQ Assignments for AIMB-564
PCI Slot 1
PCI Slot 2
PCIE x 16_1
PCIE x 4_1
Onboard
ESATA,
SATA_RAID
Onboard
PRI_IDE
A
share
d
share
d
share
d
share
d
B
C
D
E
F
G
H
-
-
-
-
-
-
shared shared -
-
-
-
-
-
shared -
-
-
-
-
-
-
-
-
-
share d
-
share d
-
-
-
-
-
AIMB-564 User Manual
-
24
-
Table 1.3: IRQ Assignments for AIMB-564
Onboard HD
Audio
(AD1988)
Onboard GbEthernet
(82566DM)
USB 2.0
EHCI#1
USB 2.0
EHCI#2
USB12
UHCI#1
USB34
UHCI#2
USB56
UHCI#3
USB78
UHCI#4
USB910
UHCI#5
SATA1/2/5/6
(ICH8DO)
SATA3/4
(ICH8DO)
IDE-R controller
KT controller
-
-
-
-
-
-
share d
-
shared -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
share d
share d
-
share
d
share d
share
d
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
share d
share d
-
-
share d
share
d
share d
shared -
25
-
Chapter 1 Product Information
1.7.4
PCI Slots
The PCI slots support cards such as a LAN card, SCSI card, USB card,
and other cards that comply with PCI specifications. The figure shows a
LAN card installed on a PCI slot.
1.7.5
PCI Express x4 Slot
This motherboard supports PCI Express x4 network cards, SCSI cards
and other cards that comply with the PCI Express specifications. The following figure shows a network card installed on the PCI Express x4 slot.
AIMB-564 User Manual
26
1.7.6
PCI Express x16 Slot
This motherboard supports PCI Express x16 graphic cards that comply
with the PCI Express specifications. The figure shows a graphics card
installed on the PCI Express x16 slot.
27
Chapter 1 Product Information
1.8 Jumper
1.8.1
Clear RTC RAM (CLRTC)
AIMB-564 User Manual
28
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system setup
parameters by erasing the CMOS RTC RAM data. The onboard button
cell battery powers the RAM data in CMOS, which include system setup
information such as system passwords.
To erase the RTC RAM:
1.
2.
3.
4.
5.
6.
Turn OFF the computer and unplug the power cord.
Remove the onboard battery.
Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the
cap on pins 2-3 for about 5~10 seconds, then move the cap back to
pins 1-2.
Reinstall the battery.
Plug the power cord and turn ON the computer.
Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
Except when clearing the RTC RAM, never remove
the cap on CLRTC jumper default position. Removing
the cap will cause system boot failure!
R
P5B-VM DO
Caution!
CLRTC
1 2
Normal
(Default)
2 3
Clear CMOS
P5B-VM DO Clear RTC RAM
Figure 1.7: Clear RTC RAM
29
Chapter 1 Product Information
Note:
1.8.2
You do not need to clear the RTC when the system hangs due
to overclocking. For system failure due to overclocking, use
the C.P.R. (CPU Parameter Recall) feature. Shut down and
reboot the system so the BIOS can automatically reset
parameter settings to default values.
Due to chipset limitations, AC power off is required prior to
using the C.P.R. function. You must turn off and on the power
supply or unplug and plug the power cord before rebooting the
system.
Keyboard Power (3-pin KBPWR)
This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when
you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the
+5VSB lead, and a corresponding setting in the BIOS.
P5B-VM DO
KBPWR
2
1
R
+5V
(Default)
P5B-VM DO Keyboard Power Setting
Figure 1.8: Keyboard Power Setting
AIMB-564 User Manual
30
3
2
+5VSB
1.9 Connectors
1.9.1
1.
2.
3.
4.
Rear Panel Connectors
PS/2 mouse port (green). This port is for a PS/2 mouse.
Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices.
IEEE 1394a port. This 6-pin IEEE 1394a port provides high-speed
connectivity for audio/video devices, storage peripherals, PCs, or
portable devices.
LAN (RJ-45) port. Supported by Realtek® Gigabit LAN controller, this port allows Gigabit connection to a Local Area Network
(LAN) through a network hub. Refer to the table below for the
LAN port LED indications.
LAN port LED indications
Table 1.4: Activity/Link Speed LED
Status
OFF
ORANGE
BLINKING
Description
No link
Linked
Data activity
Status
OFF
ORANGE
GREEN
31
Description
10 Mbps connection
100 Mbps connection
1 Gbps connection
Chapter 1 Product Information
5.
6.
7.
8.
9.
10.
Rear Speaker Out port (black). This port connects the rear speakers in a 4-channel, 6-channel, or 8-channel audio configuration.
Center/Subwoofer port (orange). This port connects the center/
subwoofer speakers.
Line In port (light blue). This port connects the tape, CD, DVD
player, or other audio sources.
Line Out port (lime). This port connects a headphone or a speaker.
In 4-channel, 6-channel, and 8-channel configuration, the function
of this port becomes Front Speaker Out.
Microphone port (pink). This port connects a microphone.
Side Speaker Out port (gray). This port connects the side speakers in an 8-channel audio configuration.
Note:
Refer to the audio configuration table below for the function of
the audio ports in 2, 4, 6, or 8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Table 1.5: Audio 2, 4, 6, or 8-Channel Config
Port
Headset
4-channel
2-channel
6-channel
8-channel
Light
Blue
Line In
Line In
Line In
Line In
Lime
Line Out
Pink
Mic In
Front Speaker
Out
Mic In
Front Speaker
Out
Mic In
Center/Subwoofer
Rear Speaker
Out
Side Speaker
Out
Orange -
-
Black
-
Rear Speaker
Out
Front Speaker
Out
Mic In
Center/Subwoofer
Rear Speaker
Out
Gray
-
-
-
11.
12.
13.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
VGA port. This port is for a VGA monitor or other VGA-compatible devices.
AIMB-564 User Manual
32
14.
External SATA port. This port connects to an external Serial ATA
hard disk drive. To configure a RAID 0, a RAID 1, or a JBOD set,
install and external Serial ATA hard disk drive and an internal
Serial ATA hard disk drive to the SATA connector labeled
SATA_RAID or SATA_RAID1.
Note:
The external SATA port supports external Serial ATA 3.0 Gb
devices. Longer cables support higher power requirements to
deliver signals up to two meters away, and enable improved
hot-swap function.
Note:
1. Before creating a RAID set using Serial ATA hard disks,
make sure that you have connected the Serial ATA signal
cable and installed Serial ATA hard disk drives; otherwise,
you cannot enter the JMicron RAID utility and SATA BIOS
setup during POST.
2. If you intend to create a RAID configuration using this connector, set the JMicron SATA Controller Mode item in the
BIOS to [RAID]. See section “2.4.6 Onboard Device Configuration” for details.
Caution!
DO NOT insert a different connector to this port.
DO NOT unplug the external Serial ATA box when a
RAID 0 or JBOD is configured.
15.
PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
33
Chapter 1 Product Information
1.9.2
1.
Internal Connectors
Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other end to
the signal connector at the back of the floppy disk drive.
Note:
Pin 5 on the connector is removed to prevent incorrect cable
connection when using a FDD cable with a covered Pin 5.
R
P5B-VM DO
FLOPPY
PIN 1
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
Figure 1.9: Floppy Disk Drive Connector
2.
Digital Audio connector (4-1 pin SPDIF_OUT)
R
P5B-VM DO
This connector is for the S/PDIF audio module to allow digital sound output. Connect one end of the S/PDIF audio cable to this connector and the
other end to the S/PDIF module.
SPDIF_OUT
GND
Spdif out
+5V
P5B-VM DO SPDIF OUT connector
Figure 1.10: SPDIF OUT connector
Note:
The S/PDIF out module is purchased separately.
AIMB-564 User Manual
34
3.
IDE connector (40-1 pin PRI_EIDE)
The onboard IDE connector is for the Ultra DMA 133/100/66 signal
cable. There are three connectors on each Ultra DMA 133/100/66 signal
cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device.
Drive jumper setting
Mode of device(s) Cable connector
Black
Single Cable-Select or Master
device
Two
Cable-Select
devices
Master
Slave
Master
Slave
Master
Slave
Black
Gray
Black or gray
Pin 20 on the IDE connector is removed to match the covered
hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.
Use the 80-conductor IDE cable for Ultra DMA 133/100/66
IDE devices.
Note:
If any device jumper is set as “Cable-Select,” make sure all
other device jumpers have the same setting.
R
P5B-VM DO
Note:
PRI_EIDE
PIN1
NOTE: Orient the red markings
(usually zigzag) on the ID
ribbon cable to PIN 1.
P5B-VM DO IDE connector
Figure 1.11: AIMB-564 IDE connector
35
Chapter 1 Product Information
4.
ICH8DO Serial ATA connectors (7-pin SATA1[red], SATA2
[red], SATA3 [red], SATA4 [red], SATA5 [black], SATA6
[black])
GND
RSATA_RXN2
RSATA_RXP2
GND
RSATA_TXN2
RSATA_TXP2
GND
GND
RSATA_RXN6
RSATA_RXP6
GND
RSATA_TXN6
RSATA_TXP6
GND
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
GND
RSATA_RXN5
RSATA_RXP5
GND
RSATA_TXN5
RSATA_TXP5
GND
SATA2
SATA5
SATA6
GND
RSATA_RXN4
RSATA_RXP4
GND
RSATA_TXN4
RSATA_TXP4
GND
P5B-VM DO SATA connectors
SATA1
GND
RSATA_RXN3
RSATA_RXP3
GND
RSATA_TXN3
RSATA_TXP3
GND
R
P5B-VM DO
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
SATA3
SATA4
Figure 1.12: SATA connectors
Note:
Connect the right-angle side of the SATA signal cable to a
SATA device. Or you may connect the right-angle side of the
SATA cable to the onboard SATA port to avoid mechanical
conflict with large graphics cards.
AIMB-564 User Manual
36
5.
IEEE 1394a port connector (10-1 pin IE1394_2)
TPA1GND
TPB1+12V
GND
R
P5B-VM DO
This connector is for an IEEE 1394a port. Connect the IEEE 1394a module cable to this connector, then install the module to a slot opening at the
back of the system chassis.
IE1394_2
P5B-VM DO IEEE 1394a Connector
TPA1+
GND
TPB1+
+12V
1
Figure 1.13: IEEE 1394a Connector
Note:
The IEEE 1394a module is purchased separately.
37
Chapter 1 Product Information
6.
JMicron JMB363® Serial ATA RAID connector (7-pin
SATA_RAID1)
This connector is for a Serial ATA signal cable. This connector supports a
Serial ATA hard disk drive, which you can combine with an external
Serial ATA hard disk drive to configure for RAID via the onboard Serial
ATA RAID controller.
The JMicron controller mode item in the BIOS is set to
[BASIC] by default.
When set to [RAID], this item allows you to use the connectors
to build a RAID set. See section “2.4.6 Onboard Device Configuration” for details.
P5B-VM DO
Note:
R
SATA_RAID1
GND
RSATA _RXN1
RSATA _RXP1
GND
RSATA _TXN1
RSATA _TXP1
GND
P5B VM DO SATA RAID connector
Figure 1.14: SATA RAID connector
Note:
Before creating a RAID set using Serial ATA hard disks, make
sure that you have connected the Serial ATA signal cables
and installed Serial ATA hard disk drives; otherwise, you cannot enter the JMicron® JMB363 RAID utility and SATA BIOS
setup during POST.
AIMB-564 User Manual
38
7.
TPM connector (20-1 pin TPM_SLOT)
R
P5B-VM DO
This connector supports a Trusted Platform Module (TPM) system,
which can securely store keys, digital certificates, passwords, and data. A
TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. See section “2.4.3 TPM Configuration” for details.
TPM
P5B-VM DO SATA RAID connector
Figure 1.15: TPM connector
39
Chapter 1 Product Information
8.
USB connectors (10-1 pin USB56, USB 78, USB910)
USB+5V
USB_P10USB_P10+
GND
NC
USB+5V
USB_P9USB_P9+
GND
USB910
USB+5V
USB_P7USB_P7+
GND
USB78
USB+5V
USB_P5USB_P5+
GND
USB56
USB+5V
USB_P8USB_P8+
GND
NC
USB+5V
USB_P6USB_P6+
GND
NC
R
These connectors are for USB 2.0 ports. Connect the USB module cable
to any of these connectors, then install the module to a slot opening at the
back of the system chassis. These USB connectors comply with USB 2.0
specification that supports a connection speed of up to 480 Mbps.
Figure 1.16: USB 2.0 connectors
Caution!
Note:
Never connect a 1394 cable to the USB connectors.
Doing so will damage the motherboard!
The USB module is purchased separately.
AIMB-564 User Manual
40
9.
Optical drive audio connector (4-pin CD)
R
These connectors allow you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, or MPEG card.
CD
(black)
Right Audio Channel
Ground
Ground
Left Audio Channel
Figure 1.17: Internal Audio Connector
10.
CPU, chassis, and power fan connectors (4-pin CPU_FAN, 3pin CHA_FAN, 3-pin CHA_FAN2, 3-pin PWR_FAN)
The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W
max.) or a total of 1 A ~ 7 A (84 W max.) at +12V. Connect the fan
cables to the fan connectors on the motherboard, making sure that the
black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the
motherboard components. These are not jumpers! Do not
place jumper caps on the fan connectors!
CPU_FAN
PWR_FAN
CPU_FAN
GND
CPU FAN PWR
CPU FAN IN
CPU FAN PWM
CHA_FAN
R
Note:
PWR_FAN
GND
+12V
Rotation
CHA_FAN2
CHA_FAN
CHA_FAN2
GND
+12V
Rotation
GND
+12V
Rotation
Figure 1.18: Fan connectors
41
Chapter 1 Product Information
11.
Serial port connector (10-1 pin COM1)
This connector is for a serial (COM) port. Connect the serial port module
cable to this connector, then install the module to a slot opening at the
back of the system chassis.
COM1
R
PIN1
Figure 1.19: Serial port connector
Note:
12.
The COM module is purchased separately.
Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch cable to
this connector. The chassis intrusion sensor or switch sends a high-level
signal to this connector when a chassis component is removed or
replaced. The signal is then generated as a chassis intrusion event.
Chassis Signal
GND
+5VSB_MB
R
By default, the pin labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to use
the chassis intrusion detection feature.
CHASSIS
(Default)
Figure 1.20: Chassis Intrusion connector
AIMB-564 User Manual
42
13.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that
supports either HD Audio or legacy AC’97 audio standard. Connect one
end of the front panel audio I/O module cable to this connector.
Legacy AC 97-compliant
pin definition
R
Azalia-compliant
pin definition
AAFP
HP_HD
MIC2_JD
PRESENSE#
AGND
HP_L
Jack_Sense
HP_R
MIC2_R
MIC2_L
NC
NC
NC
AGND
Line out_L
NC
Line out_R
MIC2_R
MIC2_L
Figure 1.21: Front panel audio connector
Note:
We recommend that you connect a high-definition front
panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
By default, this connector is set to [HD Audio]. If you want to
connect an AC’97 front panel audio module to this connector, set the Front Panel Support Type item in the BIOS
setup to [AC97]. See section 2.4.6 Onboard Device Configuration for details.
43
Chapter 1 Product Information
14.
ATX power connectors (24-pin EATXPWR, 4-pin EATX12V)
These connectors are for ATX power supply plugs. The power supply
plugs are designed to fit these connectors in only one orientation. Find the
proper orientation and push down firmly until the connectors completely
fit.
EATX12V
GND
+12V DC
GND
+12V DC
R
EATXPWR
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
Ground
+5 Volts
Ground
+5 Volts
Ground
+3 Volts
+3 Volts
Figure 1.22: ATX Power connector
AIMB-564 User Manual
44
Ground
+5 Volts
+5 Volts
+5 Volts
-5 Volts
Ground
Ground
Ground
PSON#
Ground
-12 Volts
+3 Volts
Note:
1. For a fully configured system, we recommend that you use
a power supply unit (PSU) that complies with ATX 12 V
Specification 2.0 (or later version) and provides a minimum
power of 400 W.
2. Do not forget to connect the 4-pin EATX12V power plug;
otherwise, the system will not boot.
3. Use of a PSU with a higher power output is recommended
when configuring a system with more power-consuming
devices. The system may become unstable or may not boot
up if the power is inadequate.
4. The ATX 12 V Specification 2.0-compliant (400W) PSU has
been tested to support the motherboard power requirements with the following configuration:
CPU: Intel® Pentium® Extreme 3.73GHz
Memory: 512 MB DDR2 (x4)
Parallel ATA device: IDE hard disk drive
Serial ATA device: SATA hard disk drive (x2)
Optical drive: DVD-RW
45
Chapter 1 Product Information
AIMB-564 User Manual
46
CHAPTER
2
Award BIOS Setup
Chapter 2
Award BIOS Setup
2.1 Introduction
2.1.1
BIOS Setup Program
This motherboard supports a programmable firmware chip that you can
update.
Use the BIOS Setup program when you are installing a motherboard,
reconfiguring your system, or prompted to “Run Setup”. This section
explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you can change
the configuration of your computer in the future. For example, you can
enable the security password feature or change the power management
settings. This requires you to reconfigure your system using the BIOS
Setup program so that the computer can recognize these changes and
record them in the CMOS RAM of the SPI chip.
The firmware chip on the motherboard stores the Setup utility. When you
start up the computer, the system provides you with the opportunity to run
this program. Press <Del> during the Power-On Self-Test (POST) to
enter the Setup utility; otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, reboot the system by doing any of
the following procedures:
• Restart using the OS standard shut-down procedure.
• Press <Ctrl>+<Alt>+<Del> simultaneously.
• Press the reset button on the system chassis.
• Press the power button to turn the system off then back on.
The Setup program is designed to make it as easy to use as possible.
Being a menu-driven program, it lets you scroll through the various submenus and make your selections from the available options using the navigation keys.
Caution!
Using the power button, reset button, or the
<Ctrl>+<Alt>+<Del> keys to force a reset from a running operating system can cause damage to your
data or system. We recommend to always shut-down
the system properly from the operating system.
AIMB-564 User Manual
48
Note:
1. The default BIOS settings for this motherboard apply for
most conditions to ensure optimum performance. If the
system becomes unstable after changing any BIOS settings, load the default settings to ensure system compatibility and stability. Select the Load Setup Defaults item
under the Exit Menu.
2. The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you
see on your screen.
3. Save a copy of the original motherboard BIOS file to a
bootable floppy disk or a USB flash disk in case you need
to restore the BIOS in the future.
2.1.2
CMOS RAM Auto-backup and Restore
The CMOS RAM is powered by an onboard button cell battery. When
you finish BIOS setup, the data in CMOS RAM will be automatically
backed up to Flash ROM. If operation in harsh industrial environments
causes a soft error, BIOS will recheck the data in CMOS RAM and automatically restore the original data in Flash ROM to CMOS RAM for
booting.
Note:
If you intend to change the CMOS setting without restoring
the previous backup, you have to click on “DEL” within two
seconds of the “CMOS checksum error...” display screen
message appearing. Then enter the “Setup” screen to modify
the data. If the “CMOS checksum error...” message appears
over and over, please check to see if you need to replace the
battery in your system.
49
Chapter 2 Product Information
2.2 Entering Setup
Turn on the computer and press <Del> to enter the BIOS setup.
Figure 2.1: Award BIOS Setup initial screen
AIMB-564 User Manual
50
2.3 Standard CMOS Setup
Figure 2.2: Standard CMOS Features Screen
2.3.1
Date
The date format is <weeks>, <months>, <days>, <years>.
51
Chapter 2 Product Information
2.3.2
Time
The time format is <hours> <minutes> <seconds>, based on the 24-hour
clock.
2.3.3
IDE Channel 0/1 Master/Slave
• IDE HDD Auto-Detection: Press “Enter” to select this option for
automatic device detection.
• IDE Device Setup:
Auto: Automatically detects IDE devices during POST
None: Select this when no IDE device is used. The system will skip the
auto-detection step to make system start up faster.
Manual: User can manually input the correct settings.
• Access Mode: The options are CHS/LBA/Large/Auto
• Capacity: Capacity of currently installed hard disk.
• Cylinder: Number of cylinders
• Head: Number of heads
• Precomp: Write precomp
• Landing Zone: Landing zone
• Sector: Number of sectors
2.3.4
Drive A / Drive B
This category identifies the types of floppy disk drives installed in the
system. The options are: None/360K, 5.25"/1.2M, 5.25"/720K, 3.5"/
1.44M, 3.5"/2.88M, 3.5".
2.3.5
Video
This category detects the type of adapter used for the primary system
monitor that must match your video display card and monitor.
• EGA / VGA: Enhanced Graphics Adapter/Video Graphics Array. For
EGA, VGA, SVGA, or PGA monitor adapters.
• CGA 40: Color Graphics Adapter, power up in 40 column mode.
• CGA 80: Color Graphics Adapter, power up in 80 column mode.
• MONO: Monochrome adapter, includes high resolution monochrome
adapters
AIMB-564 User Manual
52
2.3.6
Halt On
This category determines whether system start-up will halt or not when
an error is detected during power up.
The options are: No Errors/ All Errors/ All, But Keyboard/ All, But Diskette/ All, But Disk/Key
2.3.7
Memory
This category displays base memory, extended memory, and total memory detected during POST (Power On Self Test).
2.4 Advanced BIOS Features
The “Advanced BIOS Features” screen appears when choosing the
“Advanced BIOS Features” item from the “Initial Setup Screen” menu. It
allows the user to configure the AIMB-764 according to his particular
requirements. Below are some major items that are provided in the
Advanced BIOS Features screen. A quick booting function is provided
for your convenience. Simply enable the Quick Booting item to save
yourself valuable time.
Figure 2.3: Advanced BIOS Features screen
53
Chapter 2 Product Information
2.4.1
CPU Features
Thermal Management
This feature controls the activation of the Thermal Monitor's automatic
mode. It allows you to determine when the Pentium 4's Thermal Monitor
should be activated in automatic mode after the system boots. For example, with the default value of 16 Minutes, the BIOS activates the Thermal
Monitor in automatic mode 16 minutes after the system starts booting up.
The choices are 4 Min, 8 Min, 16 Min, and 32 Min.
Limit CPUID MaxVal
Set Limit CPUID MaxVa1 to 3. This should be disabled for WinXP.
C1E Function:
Sets the CPU C1E function.
Execute Disable Bit
When disabled, forces the XD feature flag to always return 0.
2.4.2
Hard Disk Boot Priority
Set hard disk boot device priority.
2.4.3
Virus Warning
Enables or disables the virus warning.
2.4.4
CPU L1, L2 & L3 Cache
Enabling this feature speeds up memory access. The commands are
“Enabled” or “Disabled.”
2.4.5
Quick Power On Self Test
This allows the system to skip certain tests to speed up the boot-up procedure.
2.4.6
First/Second/Third Boot Device
The BIOS tries to load the OS from the devices in the sequence set here.
The options are: “Floppy”, “LS120”, “Hard disk”, “CDROM”, “ZIP100”,
“USB-FDD”, “USB-ZIP”, “USBCDROM”, “USB-HDD”, “LAN”, and
“Disabled”.
2.4.7
Boot Other Device
Use this to boot another device. The options are “Enabled” and “Disabled”.
AIMB-564 User Manual
54
2.4.8
Swap Floppy Drive
If the system has two floppy drives, choose “Enabled” to assign physical
drive B to logical drive A and vice-versa. The commands are “Enabled”
or “Disabled”.
2.4.9
Boot Up Floppy Seek
Selection of the command “Disabled” will speed the boot up. Selection of
“Enabled” searches disk drives during boot up.
2.4.10 Boot Up NumLock Status
Sets the boot up status Num Lock. The options are “On” and “Off”.
2.4.11 Gate A20 Option
“Normal”: A pin in the keyboard controller controls GateA20. Fast
(Default) lets chipset control GateA20.
2.4.12 Typematic Rate Setting
The typematic rate is the rate key strokes repeat as determined by the keyboard controller. The commands are “Enabled” or “Disabled”. Enabling
allows the typematic rate and delay to be selected.
2.4.13 Typematic Rate (Chars/Sec)
The BIOS accepts the following input values (characters/second) for
typematic rate: 6, 8, 10, 12, 15, 20, 24, and 30.
2.4.14 Typematic Delay (msec)
Typematic delay is the time interval between the appearances of two consecutive characters, when the key is continuously depressed. The input
values for this category are: 250, 500, 750, and 1000 (ms).
2.4.15 Security Option
This category determines whether the password is required when the system boots up or only when entering setup. The options are:
• System: The system will not boot, and access to Setup will be also
denied unless the correct password is entered at the prompt.
• Setup: The system will boot, but access to Setup will be denied unless
the correct password is entered at the prompt.
55
Chapter 2 Product Information
Note:
To disable security, select PASSWORD SETTING in the
main menu. Then, you will be asked to enter a password.
Simply press <Enter> to disable security. When security is
disabled, the system will boot and you can enter Setup
freely.
2.4.16 APIC Mode
Allows you to enable Advanced Configuration and power Interface
(ACPI) support in the Advanced Programmable Interrupt Controller
(APIC).
2.4.17 MPS Version Control For OS
(Supports Multi Processor Specification revision 1.4)
Note:
Some old MPS OS support 1.1 version only.
81.4 Support MPS Version 1.4. (Default Value)
81.1 Support MPS Version 1.1.
2.4.18 OS Select For DRAM > 64MB
Select an operating system that is running with greater than 64MB of
RAM on the system. The choices: Non-OS2, OS2.
AIMB-564 User Manual
56
2.5 Advanced Chipset Features
By choosing the “Advanced Chipset Features” option from the “Initial
Setup Screen” menu, the screen below will be displayed. This sample
screen contains the manufacturer’s default values for the AIMB-764, as
shown in Figure 3.4:
Figure 2.4: Advanced Chipset Features screen
Note:
2.5.1
DRAM default timings have been carefully chosen and
should ONLY be changed if data is being lost. Please first
contact technical support.
Memory Hole At 15M-16M
Enabling this feature reserves 15 MB to 16 MB memory address space
for ISA expansion cards that specifically require this setting. This makes
memory from 15 MB and up unavailable to the system. Expansion cards
can only access memory up to 16 MB. The default setting is “Disabled”.
57
Chapter 2 Product Information
2.5.2
Configure AMT BIOS Support (Intel® Active Management Technology)
Intel AMT Support [Enabled]
Allows you to enable or disable the Intel® AMT (Active Management
Technology). Configuration options: [Disabled] [Enabled]
Intel® Active Management Technology is the next generation of client
manageability via the wired network. Intel AMT is a set of advanced
manageability features developed as a direct result of IT customer feedback gained through Intel market research. With the new implementation
of System Defense in ICH8DO, the advanced manageability feature set of
Intel AMT is further enhanced. Further details please browse Intel web
site:www.intel.com.
Warning!
2.5.3
Intel® Active Management Technology requires
Intel® AMT-enabled software. Also, the platform
must be connected to a power source and an active
LAN port.
PEG / Onchip VGA Control
Use this field to select PEG or Onchip VGA. The default is AUTO.
2.5.4
On-Chip Frame Buffer Size
The On-Chip Frame Buffer Size can be set to 1 MB or 8 MB. This memory is shared with the system memory.
2.5.5
DVMT Mode
Displays the active system memory mode.
2.5.6
DVMT / FIXED Memory Size
Specify the size of DVMT / FIXED system memory to allocate for video
memory.
AIMB-564 User Manual
58
2.6 Integrated Peripherals
Figure 2.5: Integrated peripherals
Figure 2.6: On-Chip IDE Device
2.6.1
On board Lan Boot ROM:
Options are “Enabled” and “Disabled”. Select “Disabled” if you don’t
want to use the onboard LAN option ROM.
59
Chapter 2 Product Information
2.6.2
IDE HDD Block Mode
If your IDE hard drive supports block mode select “Enabled” for automatic detection of the optimal number of block read/writes per sector the
drive can support.
2.6.3
IDE DMA Transfer Access
Use this field to enable or disable IDE DMA transfer access.
2.6.4
On-Chip Primary / Secondary IDE Device
IDE Primary Master/Slave PIO/UDMA Mode (Auto). The channel has
both a master and a slave, making four IDE devices possible. Because
two IDE devices may have a different Mode timing (0, 1, 2, 3, 4), it is
necessary for these to be independent. The default setting “Auto” will
allow auto detection to ensure optimal performance.
2.6.5
SATA Mode
The setting choices for the SATA Mode are IDE, RAID and AHCI Mode.
Select [IDE] if you want to have SATA function as IDE. Select [AHCI]
for Advanced Host Controller Interface (AHCI) feature, with improved
SATA performance and native command queuing. Select [RAID] to use
SATA for RAID.
2.6.6
Legacy Mode Support
This allows SATA system to support PATA mode. The choices are “Disabled” and “Enabled”.
Note:
Please refer to the PDF document Intel® Matrix Storage
Technology Quickstartguide and Intel® Matrix Storage Manager User's Manual on this CD (in the MANUAL folder) to
understand the necessary steps to build and configure your
RAID 0, 1, 10, 5 system using the Intel® Matrix Storage Technology and Matrix Storage Manager.
AIMB-564 User Manual
60
Figure 2.7: USB device setting
2.6.7
USB 1.0 Controller
Select “Enabled” if your system contains a Universal Serial Bus (USB)
controller and you have USB peripherals. The choices are “Enabled” and
“Disabled”.
2.6.8
USB Operation Mode
Set the USB 2.0 controller to Hi Speed (480 Mbps) or Full Speed (12
Mbps).
2.6.9
USB Storage Function:
Select “Enabled” if you plan to use an external USB storage device to
boot system under DOS mode. The choices are “Enabled” and “Disabled”.
2.6.10 USB 2.0 Controller
This entry is used to disable/enable the USB 2.0 controller only. The
BIOS itself may or may not have high-speed USB support. If the BIOS
has high speed USB support built in, the support will automatically turn
on when a high speed device is attached. The choices are “Enabled” or
“Disabled”.
61
Chapter 2 Product Information
2.6.11 USB Keyboard / Mouse Support
Select “Enabled” if you plan to use a USB keyboard. The choices are
“Enabled” and “Disabled”.
Figure 2.8: Onboard Device
2.6.12 HD Audio Codec
Allows you to enable or disable the High Definition Audio Controller.
Configuration options: [Enabled] [Disabled]
AIMB-564 User Manual
62
Figure 2.9: Super I/O Device
2.6.13 Onboard FDC Controller
When enabled, this field allows you to connect your floppy disk drives to
the onboard floppy disk drive connector instead of a separate controller
card. If you want to use a different controller card to connect the floppy
disk drives, set this field to Disabled.
2.6.14 Onboard Serial Port 1
The settings are “3F8/IRQ4”, “2F8/IRQ3”, “3E8/IRQ4”, “2E8/IRQ3”,
and “Disabled” for the on-board serial connector.
2.6.15 Onboard Serial Port 2
The settings are “3F8/IRQ4”, “2F8/IRQ3”, “3E8/IRQ4”, “2E8/IRQ3”,
and “Disabled” for the on-board serial connector.
2.6.16 Onboard Parallel Port
This field sets the address of the on-board parallel port connector. You
can select “378/IRQ7”, “278/IRQ5”, “3BC/IRQ7”, or “Disabled”. If you
install an I/O card with a parallel port, make sure there is no conflict in
the address assignments. The single board computer can support up to
three parallel ports.
63
Chapter 2 Product Information
2.6.17 Parallel Port Mode
This field allows you to set the operation mode of the parallel port. The
setting “Normal” allows normal speed operation, but in one direction
only. “EPP” allows bidirectional parallel port operation at maximum
speed. “ECP” allows the parallel port to operate in bidirectional mode and
at a speed faster than the maximum data transfer rate. “ECP + EPP”
allows normal speed operation in two-way mode.
2.6.18 EPP Mode Select
This field allows you to select EPP port type 1.7 or 1.9. The choices are
“EPP1.9” and “EPP1.7”.
2.6.19 ECP Mode Use DMA
This selection is available only if you select “ECP” or “ECP + EPP” in
the Parallel Port Mode field. In ECP Mode, you can select DMA channel
1 or DMA channel 3. Leave this field on the default setting.
2.6.20 PWRON After PWR-Fail
Use this to set up the system after power failure. The “Off” setting keeps
the system powered off after power failure, the “On” setting boots up the
system after failure.
AIMB-564 User Manual
64
2.7 Power Management Setup
The power management setup controls the single board computer's
“green” features to save power. The following screen shows the manufacturer’s defaults.
Figure 2.10: Power management setup screen
2.7.1
ACPI Function
The choices are: “Enabled” and “Disabled”.
2.7.2
ACPI Suspend Type
This item allows you to set ACPI suspend type to S1/POS(Power On Suspend).
2.7.3
Run VGA BIOS if S3 Resume
Select “Auto” to run VGA BIOS if S3 resumes automatically. “Yes”
enables running VGA BIOS if S3 resumes. “No” disables this function.
65
Chapter 2 Product Information
2.7.4
Power Management
This category allows you to select the type (or degree) of power saving
and is directly related to the following modes:
• HDD Power Down
• Suspend Mode
There are three selections for Power Management, and they have fixed
mode settings.
Table 2.1: Power Saving
Saving Mode
Function
Min Saving
Minimum power management., Suspend Mode = 1
hr., and HDD Power Down = 15 min.
Max Saving
Maximum power management., Suspend Mode = 1
min., and HDD Power Down = 1 min.
User Defined
(Default)
Allows you to set each mode individually. When not
disabled, each of the ranges are from 1 min. to 1 hr.
except for HDD Power Down which ranges from 1
min. to 15 min., and disabled.
2.7.5
Video Off Method
Use this to select the method to turn off the video. The choices are “Blank
Screen”, “V/H SYNC+ Blank”, and “DPMS”.
2.7.6
Video Off In Suspend
When the system is in suspend mode, the video will turn off. The choices
are “No” and “Yes”.
2.7.7
Suspend Type
The choices are “Stop Grant” and “PwrOn Suspend”.
2.7.8
Suspend Mode
Please refer to 3.7.5.
2.7.9
HDD Power Down
Please refer to 3.7.5.
AIMB-564 User Manual
66
2.7.10 Soft-Off by PWR-BTTN
If you choose “Instant-Off”, then pushing the ATX soft power switch button once will switch the system to “system off” power mode. You can
choose “Delay 4 sec”. If you do, then pushing the button for more than 4
seconds will turn off the system, whereas pushing the button momentarily
(for less than 4 seconds) will switch the system to “suspend” mode.
2.7.11 PowerOn by Modem or Power On by Ring
To enable or disable the function to power on the system via a Modem
connection from a remote host. The choice “Enabled” and “Disabled”.
2.7.12 USB KB Wake Up From S3
When enabled, enter any key to wake up the system from S3 state. The
choices are “Enabled” and “Disabled”.
2.7.13 PowerOn by Alarm or Resume by Alarm
The choices are “Enabled” and “Disabled”. Fields that follow below indicate date of current month and time of alarm settings, if enabled.
2.7.14 Wake-Up by PCI card
When enabled, the system will resume from suspend mode if Primary
IDE 0 (1) or Secondary IDE 0 (1) becomes active. The choices are
“Enabled” and “Disabled”.
2.7.15 FDD, COM, LPT PORT
When enabled, the system will resume from suspend mode if the FDD,
interface, COM port, or LPT port is active. The choices are “Enabled”
and “Disabled”.
2.7.16 PCI PIRQ [A-D]#
When enabled, the system resumes from suspend mode if an interrupt
occurs. The choices are “Enabled” and “Disabled”.
67
Chapter 2 Product Information
2.8 PnP/PCI Configuration
Figure 2.11: PnP/PCI configurations screen
2.8.1
Init Display First
Choose the first display interface to initiate while booting. The choice is
“PCI Slot” or “Onboard”.
2.8.2
Reset Configuration Data
The default is “Disabled”. Select “Enabled” to reset Extended System
Configuration Data (ESCD) if you have installed a new add-on card, and
system configuration is in such a state that the OS cannot boot.
2.8.3
Resources Controlled By
The commands here are “Auto(ESCD)” or “Manual”. Choosing “Manual” requires you to choose resources from the following sub-menu.
“Auto(ESCD)” automatically configures all of the boot and Plug and Play
devices, but you must be using Windows 95 or above.
2.8.4
PCI / VGA Palette Snoop
This is set to “Disabled” by default.
2.8.5
Maximum Payload Size
This allows you to set the maximum TLP payload size for PCIe devices.
The options are [128 bytes].
AIMB-564 User Manual
68
2.9 PC Health Status
Figure 2.12: PC Health Status Screen
2.9.1
System Temperature
This shows you the current temperature of system.
2.9.2
CPU FAN Speed
This shows the current CPU FAN operating speed.
2.9.3
System FAN Speed
This shows the current System FAN, including Power and Chassis fan,
operating speed.
2.9.4
VCORE and Other Voltages
This shows the voltage of VCORE, +3.3, +5V, +12V, -12V and
VBAT(V).
69
Chapter 2 Product Information
2.10 Frequency / Voltage Control
Figure 2.13: Spread Spectrum Frequency/Voltage Control screen
2.10.1 CPU Clock Ratio Unlock
It is suggested to keep this set this as disabled.
2.10.2 CPU Clock Ratio
Set CPU Ratio if CPU Ratio unlock is enabled.
The range is 8X~24X, depending on CPU Clock Ratio.
2.10.3 Spread Spectrum
This setting allows you to reduce EMI by modulating the signals the CPU
generates so that the spikes are reduced to flatter curves. This is achieved
by varying the frequency slightly so that the signal does not use any particular frequency for more than a moment. The choices are “Disabled”
and “Enabled”.
AIMB-564 User Manual
70
2.11 TPM Support
Figure 2.14: Security Chip Configuration
The items in this menu allow you to set the TPM (Trusted Platform Module) features. Select an item and then press <Enabled> to display the configuration options.
2.11.1 TPM Support [Disabled]
This item is not configurable.
2.11.2 TPM Status [No Change]
This item is not configurable.
Note:
To enable the TPM function, set the TPM Support item to
[Enabled] and then save the change (see 2.13 Exit menu. for
details). After rebooting, the TPM Configuration menu will
change into the following one.
71
Chapter 2 Product Information
Figure 2.15: Security Chip Configuration
Figure 2.16: TPM POST Screen
Caution!
Once the data saved in the TPM security chip is
cleared, it can never be restored.
AIMB-564 User Manual
72
2.12 Password Setting
Follow these steps to change the password.
1.
Choose the “Set Password” option from the “Initial Setup Screen”
menu and press <Enter>. The screen displays the following message:
Please Enter Your Password
2.
Press <Enter>.
3.
If the CMOS is good and this option has been used to change the
default password, the user is asked for the password stored in the
CMOS. The screen displays the following message:
Please Confirm Your Password
4.
Type the current password and press <Enter>.
5.
After pressing <Enter> (ROM password) or the current password
(user-defined), you can change the password stored in the CMOS.
The password must be no longer than eight (8) characters.
Remember, to enable the password setting feature, you must first select
either “Setup” or “System” from the “Advanced BIOS Features” menu.
73
Chapter 2 Product Information
2.13 Save & Exit Setup
If you select this and press <Enter>, the values entered in the setup utilities will be recorded in the CMOS memory of the chipset. The processor
will check this every time you turn your system on and compare this to
what it finds as it checks the system. This record is required for the system to operate.
AIMB-564 User Manual
74
2.14 Exit Without Saving
Selecting this option and pressing <Enter> lets you exit the setup program
without recording any new values or changing old ones.
75
Chapter 2 Product Information
AIMB-564 User Manual
76
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising