Bakers Pride | Dante Series XXE | Operating instructions | Bakers Pride Dante Series XXE Operating instructions

Bakers Pride Dante Series XXE Operating instructions
INSTALLATION AND OPERATING INSTRUCTIONS
Dante
SERIES
GAS CHAR BROILERS
Model: XXE
INTENDED FOR OTHER THAN HOUSEHOLD USE
RETAIN THIS MANUAL FOR FUTURE REFERENCE
BROILER MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES
IMPORTANT INSTRUCTIONS
After the gas supply has been connected to your unit, it is extremely important to check piping for possible
leaks. To do this, use soap and water solution or solutions which are expressly made for this purpose. DO
NOT USE matches, candles, flames, or other sources of ignition since these methods are extremely
dangerous.
Post in a prominent location instructions to be followed in the event you smell gas. Obtain these instructions
from your local gas supplier.
!
FOR YOUR SAFETY
!
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
WARNING
!
Improper installation, adjustment, alteration, service or maintenance can cause
property damage, injury or death. Read the Installation, Operating and
Maintenance Instructions thoroughly before installing or servicing this equipment.
!
This equipment has been engineered to provide you with year round dependable service when used
according to the instructions in this manual and standard commercial kitchen practices.
CERTIFIED
R
P/N U4144A 9/08
BAKERS PRIDE OVEN CO., INC.
30 Pine Street
New Rochelle, NY 10801
+1 (914) 576-0200 Phone
+1 (914) 576-0605 Fax
(800) 431-2745 US & Canada
www.bakerspride.com Web Address
Info@bakerspride.com E-Mail Address
1
TABLE OF CONTENTS
I. INSTALLATION INSTRUCTIONS
SECTION
1
2
3
4
5
6
7
8
9
10
11
ITEM
Installation
Clearances
Gas Connection
Burners
Radiants
Top Grates
Lighting Instructions
Grease Pan
Griddle Plate
Additional Installation Instructions
Installation with Casters
PAGE
2
3
3
3
4
4
4
4
4
4
5
II. OPERATING INSTRUCTIONS
SECTION
1
2
ITEM
Lighting Procedure
Broiling
PAGE
5
5
III. MAINTENANCE
SECTION
1
2
3
4
ITEM
Service
Care & Cleaning
Cleaning Tools
Troubleshooting Chart
PAGE
5
5
6
6
IV. ILLUSTRATIONS
ITEM
Manifold & Valve Assembly Views
Parts List w/Exploded Views
PAGE
7
8
V. WARRANTY
ITEM
Bakers Pride Limited Warranty
PAGE
12
I. INSTALLATION INSTRUCTIONS
1. INSTALLATION:
(A)
(B)
INSTALLATION of this broiler must conform with the latest edition of National Fuel Gas Code
and/or local codes, ( the American National Standard 2-223.1 in USA and CAN/CGA-B149.1 or 2
Installation Code in Canada). In Europe, this appliance must be installed in conformity with current
regulations and used only in a well ventilated space.
In MASSACHUSETTS, All gas products must be installed by a “Massachusetts” licensed plumber
or gas fitter. Ventilation hoods must be installed in accordance with NFPA-96, current edition, with
interlocks as described in that standard.
2
2. ACCEPTABLE CLEARANCES:
(A)
USA and Canada.
Due to intense heat generated by radiation, in USA and Canada these broilers should be installed in noncombustible locations only, including the areas above the grate level.
MINIMUM CLEARANCE FROM NON-COMBUSTIBLE CONSTRUCTION:
Right Side
50mm(2")
(B)
Left Side
50mm (2")
Back
50mm (2")
European Community Countries
Minimum clearance from:
Combustible construction
Non-combustible construction
Right Side
Left Side
Back
Floor
250mm
50mm
250mm
50mm
250mm
50mm
150mm
100mm
3. GAS CONNECTION:
The gas pressure regulator supplied must be installed at the gas inlet of each broiler unless required
otherwise by local codes. Each regulator is adjusted to yield a manifold pressure of 3.5" water column (9
mbar) for natural gas or 10" water column (25 m bar) for propane gas. Units for propane gas are available
for use in USA and Canada only.
Recommended minimum gas supply lines are listed below:
All XXE Models
3/4"
(19 mm )
NOTE: A shut off valve in a readily accessible location must be installed on the gas supply line before
connecting it to the unit.
For units using propane gas supply In USA and Canada lines less than' 1/2" (12.7 mm) Inside
diameter should not be used.
On the XXE series, the gas connection is located on the right rear of the unit.
BE SURE TO CAP WHICHEVER SIDE IS NOT CONNECTED.
When making gas pipe connections, pipe joint compound resistant to the action of liquefied petroleum
gases should be used.
The broiler and its individual shutoff valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressure in excess of 1/2 psig (3.45 kpa).
The broiler must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig
(3.45 kpa).
4. BURNERS
Check to see that air mixer caps on the front of all burners are adjusted and tightened, allowing half the
opening to show.
To install the burners:
(A)
Place the front venturi end of the burner into the valve assembly by fitting the center hole of
the air mixer cap over the brass orifice.
(B)
Drop the two ends of the burners over the burner support pins in the front and back of the
chamber.
3
5. RADIANTS
Mount the "A" shaped radiants over the burners with each end mounted on special supports on the front and
rear of the chamber. A radiant should be mounted over eachburner assembly..
6. TOP GRATES
Place a grate over each of the radiants. For normal operation the pointed side of the grate is facing up. For
use with foods that require extra, support, the flat side may be used.
On XXE models, grates can be placed on three levels; two positions are built into the rear of the unit; the third
position requires a special adapter which is supplied with the unit.
The adapter covers only half of the broiler. To cover the entire unit. optional adapters can be ordered.
7. LIGHTING:
Each burner has a standing pilot burner which must be lit before the burners can be lit. To light the pilot
burners:
(A)
Turn all broiler valves to off position
(B)
Open main gas shut off valve ( provided by customer).
(C)
Press. turn counterclockwise and hold the burner control knob to the pilot burner ignition
position.
(D).
Using a lit taper, light the pilot burner
(E)
Release the knob after 30 seconds. Pilot burner should stay lit.
If the pilot burner does not remain lit, wait for 5 minutes and repeat steps C and D.
Hold the knob pressed longer before releasing.
(F)
With a screwdriver adjust the pilot burner flame to about 1/2" (12.7 mm). Turn the adjusting
screw clockwise to reduce or counterclockwise to increase the pilot burner flame.
(G)
Each burner may now be adjusted to the desired flame size by turning the individual burner
valve knob.
(H)
Turn the knob to the pilot burner ignition position to shut down the main burner.
(I)
Turn the knob to off position to shut down the pilot burners.
NOTE: WAIT FIVE MINUTES BEFORE ATTEMPTING TO RELIGHT THE PILOT
BURNERS.
8. GREASE PAN
A grease pan is provided below the burners to hold any grease that drips down past the radiants while
broiling. An additional grease drawer is provided in the front right corner of the grease pan to collect the
grease from the grease drain in the front which in turn drains into the grease collector.
Water is usually added to the grease pan to reduce flare-up and flash back. The . grease drip will extinguish
as it hits the water.
9. GRIDDLE PLATE (optional)
Griddle plates should not cover more than 50% of the BROILING area. Each Griddle Plate fits on top of two
grates. It is not necessary to remove the top grates and radiants before installing the griddle plate.
10. ADDITIONAL INSTALLATION INSTRUCTIONS
(A)
(B)
(C)
(D)
Keep the area around the broiler free and clear of combustible materials.
The provision of an adequate air supply to your broiler is essential. Provide for sufficient
outside air to enter the broiling area and assure that this air flow is not obstructed.
Air enters the burner area from the front of your broiler. Assure that this area is kept open and
unobstructed.
Servicing is accomplished through the front and top of the broiler. Assure that this area is
kept unobstructed for proper servicing and operation.
4
11. INSTALLATION WITH CASTERS
(A)
(B)
(C).
(D)
Install the casters with wheel brakes on the front of the appliance.
Installation should be made with a connector that complies with the latest edition of the
Standard for Connectors for Movable Gas Appliances (ANS/Z21.69 in USA, CAN/CGA-6.16
in Canada) and a quick disconnect device that complies with the latest edition of the
Standard for Quick Disconnect Devices for use with gas fuel (ANSIZ21.41 in USA, CAN16.9 in Canada). Adequate means must be provided to limit the movement of the appliance
without depending on the connector and any quick disconnect device or its associated
piping to limit the appliance movement.
The restraint should be attached to the center of the back about 1/2" (12.7mm ) from the
bottom.
If disconnection of the restraint is necessary, the restraint should be reconnected after the
appliance has been returned to its originally installed position.
II. OPERATING INSTRUCTIONS
1. LIGHTING PROCEDURES
See Section 7 of INSTALLATION INSTRUCTIONS.
2. BROILING
BROILER TOP GRATE MUST BE HOT ENOUGH TO MAKE BLACK CHAR-MARKS WHEN STARTING
TO BROIL.
Adequate preheating time is necessary for the food to release from the broiler and to cook properly. Allow
the unit to preheat for 20-25 minutes before broiling.
(A)
Do not press the juice out of the meat because that will cause dry products.
(B)
After broiling, allow the meat to sit covered on a heated platter for 2-5 minutes before cutting.
This will allow the juices to "settle" and the product will be more moist.
(C)
Do not use forks or other sharp objects to poke holes in the meat. Do not cut the meat as it
cooks.
(D)
Thick pieces of meat require a longer broiling time with less flare-up. Reduce flare up by
trimming excess fat for a longer broil time without burning.
(E)
Keep the unit clean. Food caught between the grate will not allow hot air to rise around the
product. This will result in uneven heating and increase the cooking time.
III. MAINTENANCE
1. SERVICE
Shut off the main gas supply before attempting any maintenance on the unit. If required, contact your dealer,
the factory, or a local service company to obtain qualified maintenance and repairs.
2. CARE AND CLEANING
(A)
(B)
The top grates should be cleaned using a stiff wire brush. If this is done daily, the
accumulation of food and fat caught in the grates and work necessary to keep them clean will
be reduced. Periodically, they should be turned over and brushed and then put back. In the
event that an extra amount of fat is accumulated on the top, due to use of low heat, we
recommend turning up the flame of this section for about an hour, which will burn off much of
the fat and residue and the brushing operation will be easier. Under no circumstances should
the grates be placed in a dishwasher. Soap, water, or any detergents should never be used
on the cast Iron grates.
Front - Sample supplied with the unit or any reputable stainless steel cleaner can be used.
5
(C)
(D)
CAUTION:
(A)
(B)
(C)
(D)
Inner panels - These are made of aluminized steel. Use hot soapy water and soft nylon scrub
pads to clean the surfaces.
Grease pan and grease collector - Grease pan and collector should be cleaned daily or more
often if necessary.
Clean the unit only when it is cold.
Always rub with the grains when cleaning.
Do not use abrasive pads for cleaning.
Do not use caustic cleaning compounds on aluminized surfaces.
3. CLEANING TOOLS
Several models of specially designed top grate brushes and grease drain scrapers are available from
Bakers Pride. Contact Bakers Pride for more information.
TROUBLESHOOTING CHART
PROBLEM
PROBABLE CAUSE
SOLUTION
Burners & pilots will
not turn on
Burners produce
excessive carbon
deposits
Main gas supply to broiler is not
turned on.
Incorrect gas type.
Incorrect gas supply pressure.
Incorrect orifices.
Turn on main gas supply.
Primary air not adjusted properly.
Pilot will not remain Pilot flame adjusted incorrectly.
Draft condition.
lit
Improper ventilation system.
Debris or grease clogging pilot
burner or thermocouple.
Pilot safety valve or thermocouple
has failed.
Overload of fatty meat.
Excessive flare-up
Broiler doesn't seem Orifices may be dirty/clogged.
Low gas pressure.
hot enough
Top grates may be dirty/clogged.
Grates &/or radiants
&/or burners &/or
gas valves warp
If the ventilation is too strong it will
suck heat from the
cooking/broiling surface.
Too many Glo-stones restricting
heat to top grates.(Glo-stone
models only).
Usually improper cleaning
methods ie; users cover grate top
w/sheet pans & crank up heat to
burn-off debris
6
Supply correct type gas.
Call local gas supplier.
Call Bakers Pride authorized service
center.
Adjust air shutter.
Adjust pilot flame.
Remove draft.
Call an HVAC specialist.
Clean debris & grease from pilot burner &
thermocouple.
Replace failed component.
Add water to grease pan.
When unit cools, check & clean orifices.
Increase gas pressure to 5" W.C. (Nat) or
10" W.C. (L.P.)
When unit cools, check & clean top
grates.
Call an HVAC specialist.
Reduce the number of Glo-stones.
Do not "Burn-Off" top grates. This causes
the firebox area to overheat excessively.
*Never cover top grates.
FIGURE 1
IV. MANIFOLD & VALVE ASSEMBLY VIEWS
XXE SERIES - FRONT VIEW
Air Mixer Cap Hold-down Screw
Manifold
Air Mixer Cap
FIGURE 2
XXE SERIES - SIDE VIEW
Pilot Burner
Flame Sensor
Burner
Valve Handle
Air Mixer Cap
Orifice
Orifice Holder
Manifold
Burner Valve
7
30 Pine Street • New Rochelle • New York • 10801
BAKERS
PRIDE
XXE-4, 6, 8, 10, 12
914 / 576 - 0200
914 / 576 - 0605 fax
1 - 800 - 431 - 2745 US & Canada
www.bakerspride.com web address
Gas Char Broiler
PARTS LIST
Dante
SERIES
Serial Number
Model Number
XXE-4
XXE-6
XXE-10
XXE-12
XXE-8
Type of Gas
Natural
Note: When ordering, ALWAYS specify Part #, Model #, Serial #, Voltage/Phase & type of Gas.
8
L.P.
Other
U6065A 9/08
30 Pine Street • New Rochelle • New York • 10801
XXE-4, 6, 8, 10, 12
914 / 576 - 0200
914 / 576 - 0605 fax
1 - 800 - 431 - 2745 US & Canada
www.bakerspride.com web address
Gas Char Broiler
BAKERS
PRIDE
Exterior / Grates
Figure A
19
16
8
1
9
7
11
2
3
4
10
13
18
14
15
12
6
5
17
20
Note: When ordering, ALWAYS specify Part #, Model #, Serial #, Voltage/Phase & type of Gas.
9
21
U6065A 9/08
30 Pine Street • New Rochelle • New York • 10801
BAKERS
PRIDE
XXE-4, 6, 8, 10, 12
914 / 576 - 0200
914 / 576 - 0605 fax
1 - 800 - 431 - 2745 US & Canada
www.bakerspride.com web address
Gas Char Broiler
Exterior / Grates
Item
Part #
Description
1
G1011K
2
Part #
Description
Top Side Trim, SS, Left
G1058K
3rd Level Bracket (XX-10) Optional
G1012K
Top Side Trim, SS, Right
G1056K
3rd Level Bracket (XX-12) Optional, 2 used
3
G1458K
Outer Side, Left (XXE)
4
G1459K
Outer Side, Right (XXE)
Work Deck, S/S (XXE-6) Optional
5
G1454K
Control Panel (XXE-4)
Work Deck, S/S (XXE-8) Optional
G1455K
Control Panel (XXE-6)
Work Deck, S/S (XXE-10) Optional
G1456K
Control Panel (XXE-8)
Work Deck, S/S (XXE-12) Optional
G1457K
Control Panel (XXE-10)
G1412K
6
7
8
9
Item
10
11
Work Deck, S/S (XXE-4) Optional
G1081X
Splash Guard, S/S (XX-4) Optional
Control Panel (XXE-12)
G1082X
Splash Guard, S/S (XX-6) Optional
G1474K
Top Front Trim (XXE-4)
G1083X
Splash Guard, S/S (XX-8) Optional
G1475K
Top Front Trim (XXE-6)
G1084X
Splash Guard, S/S (XX-10) Optional
G1476K
Top Front Trim (XXE-8)
G1237U
Splash Guard, S/S (XX-12) Optional
G1477K
Top Front Trim (XXE-10)
T3033K
Grease Pan (XX-4) 20 3/8", 1 used
G1413K
Top Front Trim (XXE-12)
T3034K
Grease Pan (XX-6 or 10) 30 7/8", 1 used
G1461K
Outer Back (XXE-4)
T3035K
Grease Pan (XX-8) 19 5/8", 2 used
G1462K
Outer Back (XXE-6)
T1036T
Grease Pan (XX-10) 19 1/4", 1 used
G1463K
Outer Back (XXE-8)
T1036T
Grease Pan (XX-12) 19 1/4", 3 used
G1464K
Outer Back (XXE-10)
13
U1043A
Name Plate, 13 1/4", Bakers Pride
G1414K
Outer Back (XXE-12)
14
S1394A
Leg, 4" Adjustable (Each)
G1021U
1st/2nd Level Assy (XX-4)
15
S1394X
Leg, 4" Adjustable (Set/4)
G1022U
1st/2nd Level Assy (XX-6)
16
T1020T
Griddle Plate (Optional) 16"
G1023U
1st/2nd Level Assy (XX-8)
17
T1006A
Grate, Top, Flat Cast Iron (5 1/4")
G1024U
1st/2nd Level Assy (XX-10)
18
T1183T
Grate, Fajita Bottom
G1247U
1st/2nd Level Assy (XX-12)
19
T1185S
Grate, Fajita Top
G1055K
3rd Level Bracket (XX-4) Optional
20
T1172T
Grate, Meat 10 1/2"
G1056K
3rd Level Bracket (XX-6) Optional
21
T1166T
Grate, Fish 10 1/2"
G1057K
3rd Level Bracket (XX-8) Optional
12
Note: When ordering, ALWAYS specify Part #, Model #, Serial #, Voltage/Phase & type of Gas.
10
U6065A 9/08
30 Pine Street • New Rochelle • New York • 10801
XXE-4, 6, 8, 10, 12
914 / 576 - 0200
914 / 576 - 0605 fax
1 - 800 - 431 - 2745 US & Canada
www.bakerspride.com web address
Gas Char Broiler
BAKERS
PRIDE
Burner / Accessories
Figure C
27
20
18
19
22 21
3
24
23
1
26
6
13
14
5
4
2
9
11
12
8
28
25
Item
Part #
Description
1
R1085P
R1086P
R1087P
R1088P
R1186A
N3068P
N5217P
R3128A
M1053A
R3181P
S1301A
L5078A
M1359A
G1472K
M1358A
M1267X
N1007A
Manifold Assy (XXE-4)
Manifold Assy (XXE-6)
Manifold Assy (XXE-8)
Manifold Assy (XXE-10)
Manifold Assy (XXE-12)
Pressure Tap Nozzle Assy
Inlet Gas Pipe (XX)
Valve, Multi Gas Cock
Valve, Junker (Old Style)
Pilot Tubing, 5" (XXE)
Knob, CE Broiler
Burner, Center Feed (XXE)
Pilot Burner
Pilot Burner Mounting Bracket (XXE)
Thermocouple, 10"
Thermocouple (used w/O.S. Junker Valve)
Compression Nut, 3/16", Female
2
3
4
5
6
7
8
9
10
11
12
13
7
Item
Part #
Description
14
15
16
17
18
19
20
N1010A
R3130A
R3044A
R3023A
T1155T
T1007A
G1470K
Ferrule, 3/16"
Orifice Hood #44, Nat (XXE)
Orifice Hood #55, LP (XXE)
Orifice Hood, Blank
Radiant, S/S (23") Standard
Radiant, Cast Iron (23") Optional
Heat Shield (XXE-4 uses 5) (XXE-6 uses 7)
21
22
23
24
25
26
27
28
M1009A
M1184A
T5017A
T5018U
T5041T
T5016A
T5019V
T5104V
(XXE-8 uses 9) (XXE-10 uses 11) (XXE-12 uses 13)
Conversion Kit (LP to Nat)
R3130A
Pressure Regulator, 3/4", 10" WC
Pressure Regulator, 3/4", 3.5" WC
Wire Brush, Chef-Aide, 18"
Spatula, Chef-Aide, 20", Single
Grate Lifter, 3' x 20"
Meat Fork
Steak Turner
Twin Head Grate Brush
Conversion Kit (Nat to LP)
R3044A
Hood Orifice # 44, Nat. (XXE-4 uses 4) (XXE-6 uses 6)
Hood Orifice #55, L.P. (XXE-4 uses 4) (XXE-6 uses 6)
(XXE-8 uses 8) (XXE-10 uses 10) (XXE-12 uses 12)
(XXE-8 uses 8) (XXE-10 uses 10) (XXE-12 uses 12)
M1184A
10
15 16 17
Pressure Regulator, 3/4", 3.5" WC (Qty. 1)
M1009A
Pressure Regulator, 3/4", 10" WC (Qty. 1)
Note: When ordering, ALWAYS specify Part #, Model #, Serial #, Voltage/Phase & type of Gas.
11
U6065A 9/08
V. BAKERS PRIDE LIMITED WARRANTY
30 Pine Street New Rochelle, New York 10801
914 / 576 - 0200 ♦ US & Canada: 1 - 800 - 431 - 2745 ♦ fax 914 / 576 - 0605
WHAT IS COVERED
This warranty covers defects in material and workmanship under normal use, and applies only to the original purchaser
providing that:
♦ The equipment has not been accidentally or intentionally damaged, altered or misused;
♦ The equipment is properly installed, adjusted, operated and maintained in accordance with National and local codes. and
in accordance with the installation instruction provided with the product;
♦ The serial number rating plate affixed to the equipment has not been defaced or removed.
WHO IS COVERED
This warranty is extended to the original purchaser and applies only to equipment purchased for use in the U.S.A.
COVERAGE PERIOD
Full size gas and electric deck ovens: Two (2) year limited parts and labor: Cyclone Convection Ovens: BCO Models: One (1)
Year limited parts and labor; GDCO Models: Two (2) Year limited parts and labor; CO II Models: Two (2) Year limited parts
and labor; (5) Year limited door warranty.
All Other Products: One (1) Year limited parts and labor.
Warranty period begins the date of dealer invoice to customer or ninety (90) days after shipment date from BAKERS PRIDE whichever comes first.
WARRANTY
COVERAGE
This warranty covers on-site labor, parts and reasonable travel time and travel expenses of the authorized service
representative up to (100) miles. round trip, and (2) hours travel time. The purchaser. however, shall be responsible for all
expenses related to travel, including time. mileage and shipping expenses on smaller counter models that may be carried into
a Factory Authorized Service Center, including the following models: PX-14. PX-16, PI8, and BK-I8.
EXCEPTIONS
All removable parts in BAKERS PRIDE Char-broilers, including but not limited to: Burners, Grates. Radiants, Stones and
Valves, are covered for a period of SIX MONTHS.
All Ceramic Baking Decks are covered for a period of THREE MONTHS. The installation of these replacement decks is the
responsibility of the purchaser.
The extended Cyclone door warranty years 3 through 5 is a parts only warranty and does not include labor, travel, milage or
any other charges.
EXCLUSIONS
♦ Failures caused by erratic voltages or gas supplies,
♦ Unauthorized repair by anyone other than a BAKERS PRIDE
Factory Authorized Service Center,
♦ Damage in shipment,
♦ Alteration, misuse or improper installation,
♦ Thermostats and safety valves with broken capillary tubes.
♦ Accessories - spatulas, forks. steak turners, grate lifters,
oven brushes, scrapers, peels. etc.,
♦ Freight - other than normal UPS charges,
♦ Ordinary wear and tear.
♦ Negligence or acts of God,
♦ Thermostat calibrations after (30) days from equipment
installation date,
♦ Air and Gas adjustments,
♦ Light bulbs,
♦ Glass doors and door adjustments.
♦ Fuses,
♦ Char-broiler work decks and cutting boards,
♦ Tightening of conveyor chains,
♦ Adjustments to burner flames and cleaning of pilot burners,
♦ Tightening of screws or fasteners.
INSTALLATION
Leveling and installation of decks. as well as proper installation and check out of all new equipment - per appropriate
installation and use materials - is the responsibility of the dealer or installer, not the manufacturer.
REPLACEMENT
PARTS
BAKERS PRIDE genuine Factory OEM parts receive a (90) day materials warranty effective from the date of installation by a
BAKERS PRIDE Factory Authorized Service Center.
This Warranty is in lieu of all other warranties, expressed or implied, and all other obligations or liabilities on the manufacturers part. BAKERS PRIDE
shall in no event be liable for any special, indirect or consequential damages, or in any event for damages in excess of the purchase price of the unit. The
repair or replacement of proven defective parts shall constitute a fulfillment of all obligations under the terms of this warranty.
Form #U4177A 1/07
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising