Acorn | A172108F-SO | Specifications | Acorn A172108F-SO Specifications

Acorn A172108F-SO Specifications
INSTALLATION, OPERATIONS
& MAINTENANCE MANUAL
A172.8UBL Series
Refrigerated Universal Bi-Level
Barrier Free, Wall Mounted Water Cooler
OR
Alternate Configuration
Standard Configuration
A172108F-UBL / A172408F-UBL / A172108F-SO / A172408F-SO
TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:
1.800.591.9360
Technical Assistance Fax: 1.626.855.4894
NOTES TO INSTALLER:
1. Please leave this documentation with the owner of the fixture when finished.
2. Please read this entire booklet before beginning the installation.
3. Check your installation for compliance with plumbing, electrical and other applicable codes.
LIMITED WARRANTY - UNITED STATES & CANADA
Acorn Engineering warrants Water Coolers, Drinking Fountains and remote Chillers are free from defects in
material or workmanship under normal use and service for a period of one year from date of shipment from the
factory. The compressor, condenser and refrigeration tubing is warranted for an additional four years after the
period described above. Acorn’s liability under this warranty shall be discharged solely by repair or replacement
of defective material, provided Acorn is notified in writing within the time periods described above.
This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of
the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Acorn under this
warranty. Acorn shall not be liable under any circumstances for incidental, consequential or direct charges
caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of
all other warranties expressed or implied. Product maintenance instructions are issued with each unit and
disregard or non-compliance with these instructions will constitute an abnormal use condition and void the
warranty. Stainless steel must be protected on jobsite during construction and must be properly maintained
after the water has been introduced into the water cooler or drinking fountain, or Acorn’s limited warranty is
void.
Acorn Engineering Company™ assumes no
responsibility for use of void or superseded data.
© Copyright Acorn Engineering, City of Industry,
CA Member of Morris Group International.
Please visit www.acorndrinkingfountains.com
for most current specifications.
7020-905-001
Date: 04/29/15
COMPLIES WITH
LIMITED EXPORT WARRANTY - One year on parts only.
ACORN
Water Coolers &
Drinking Fountains
Federal
Public Law
111-380
(No Lead)
Test rating conditions are
compliant with ARI 1010.
Member of
15125 Proctor Ave.
City of Industry, CA
91746 U.S.A.
Phone 800-591-9360
626-336-4561
w w w. a c o r n d r i n k i n g f o u n t a i n s . c o m
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
IMPORTANT
This fixture is intended to dispense water that has been lowered in temperature, but otherwise remains
unchanged by the materials in the water cooler. It is common for electrical equipment to be grounded
to water lines either within a structure or away from it. Every attempt should be made to prevent this
kind of grounding from generating electrical feedback into the water cooler creating electrolysis.
Electrolysis will cause a metallic taste or cause water metal content to increase.
NOTICE
A dielectric coupling must be used to connect the water cooler to the water supply . A nonmetallic
coupler is furnished with this water cooler to meet this requirement.
ROUGHING-IN AND DIMENSIONAL DRAWING
Prior to roughing consult with local, state, and federal codes for proper mounting height.
A172.8UBL SERIES REFRIGERATED BI-LEVEL WALL MOUNTED WATER COOLER
Note: there are no mounting changes to be made for -SO models.
A. 3/8" NCT SUPPLY INLET
B. WASTE OUTLET FOR 1-1/4" P-TRAP BY OTHERS.
C. ELECTRICAL SERVICE ROUGH.
D. Ø3/8" HANGER BRACKET PUNCHING, 3 PLACES FOR ANCHORING HARDWARE BY OTHERS.
E. Ø1/4" PUNCHING, 2 PLACES FOR ANCHORING HARDWARE BY OTHERS.
37
8"
1"
94
185
8"
D
1"
132
1"
74
65
8"
1"
24
1"
44
A
E
1"
182
*215
8"
6"
11"
165
8"
1"
202
13
8"
12" 6"
TAIL
PIECE
AIR FLOW
B
*33"
C
1"
54
77
8"
NOTES:
1. Dimensions shown for ADA compliant installation. For Child ADA 2010 compliant parallel approach
installation, decrease height of * dimensions by 2-3/4".
2. Provide clear floor space as required. Adjust vertical dimensions as required to comply with federal,
state, and local codes.
See next page for alternative mounting of units, roughing-in and dimensional drawing.
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 2 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
A172.8UBL SERIES REFRIGERATED BI-LEVEL WALL MOUNTED WATER COOLER
Note: there are no mounting changes to be made for -SO models.
1"
94
185
8"
1"
74
65
8"Typ.
1"
62
A
13
8"
6"
11"
AIR FLOW
6"
12"
TAIL
PIECE
*33"
165
8"
1"
202
D
173
8"
63
8"
B
1"
54
C
E
E
*155
8"
NOTES:
A. 3/8" NCT SUPPLY INLET
B. WASTE OUTLET FOR 1-1/4" P-TRAP
BY OTHERS.
C. ELECTRICAL SERVICE ROUGH.
1"
44
77
8" Typ.
D. Ø3/8" HANGER BRACKET PUNCHING, 3 PLACES FOR
ANCHORING HARDWARE BY OTHERS.
E. Ø5/16" PUNCHING, 2 PLACES FOR ANCHORING
HARDWARE BY OTHERS.
IMPORTANT:
1. Waste P-Trap, Water Supply Service Angle Stop Valve and 2” x 4” Electrical Plug-In Receptacle to be supplied
by others in accordance with local codes. A metallic p-trap (by others) must be used for the drain connection.
2. Provide 4” minimum clear space on fixture sides to allow for proper ventilation through cabinet louvers.
3. Water supply is 3/8” Outside Diameter copper tube. Waste is 1-1/4” Outside Diameter.
4. Completely flush supply lines of all foreign debris before connecting to fixture. Water cooler designed to not
affect taste, odor, color, or sediment. Optional water filter (Wf1) is available should any of these problems
arise from the water supply.
5. Do NOT solder copper tube when inserted into the coupler as damage to the o-ring will result.
6. All burrs must be removed from outside of cut tubes before inserting into coupler or other components.
7. Power supply must be identical in voltage, cycle and phase to that specified on the cooler data plate.
Electrical outlet and furnished power cord with plug must be used to supply power to fixture. Do NOT wire
compressor directly to the power supply.
8. This unit must be grounded per the requirements of applicable electrical codes.
9. WARNING: Warranty is voided if installation is not made following current Acorn Engineering installation
instructions and if components are assembled to the fixture that is not approved by Acorn Engineering.
10. Fixture operates within water pressure range of 20 to 105 psig. Acorn Engineering will not warranty fixtures
damaged when connected to supply lines with flow pressure lower than 20 psig or higher than 105 psig. A
pressure regulator must be furnished by others on supply line if inlet pressure is greater than 105 psig.
11. Due to cold waste water, Acorn Engineering recommends that p-trap supplied by installer be insulated to
prevent excessive condensation.
12. Per UPC 609.10- All building water supply systems in which quick acting valves are installed shall be provided
with devices to absorb the hammer caused by high pressure resulting from the quick closing of the valve.
These pressure-absorbing devices shall be approved mechanical devices. Water pressure-absorbing devices
will be installed as close as possible to the quick closing valve.
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 3 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
ITEM 23
FILLER PLATE
STANDARD WASTE CONFIGURATION
ITEM 23
FILLER PLATE
ALTERNATE WASTE CONFIGURATION
INSTALLATION:
Choose configuration; Remove and reinstall filler plate, item 23 and reverse drain assembly if
required for alternate mounting configuration.
1. Mount hanger bracket to wall horizontally level as shown in Roughing-In and Dimensional Drawing. Note:
Adjust height of bracket if bubbler outlet height is required to vary from that shown.
WARNING: Hanger Bracket MUST be securely anchored to wall with fasteners sufficient to support 3 times
the weight of cooler. If wall can not provide adequate support, order and install optional fixture support carrier.
2. Remove the bottom cover from the water cooler and set aside in a safe place. Save the screws in a secure
location for re-use in later stages of installation.
3. Hang the water coolers on the hanger brackets ensuring the bracket tabs engage AND seat in the slots in the
back of the water coolers. NOTE: Hanging of refrigerated unit first is recommended since it is the heavier of
the two. Verify water coolers are level, left to right AND front to back from bottom of unit. CAUTION: The
bubbler stream may be adversely affected if units are not square and level. Bottom of units and louvers
should be used as reference to verify unit is square and plumb.
4. Anchor the water coolers to the wall at the lower mounting points in each back panel. Shim lower mounting
points to level unit if necessary.
5. Outlet tube from evaporator has an in-line tee with a tube going to the refrigerated unit's valve and the "TEE"
not connected. Connect the loose supply tube from refrigerated unit to the "TEE".
6. Thoroughly flush the 3/8” O.D. supply line and then connect water cooler to water supply angle stop valve (by
others) with supplied 3/8” O.D. copper tube.
7. Use supplied flexible hose and clamps to connect waste tailpiece from the upper unit to the waste tailpiece of
lower unit and then make up 1-1/4” O.D. p-trap waste connection. Waste p-trap by others.
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 4 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
START UP:
1. Before connecting power supply and assembling bottom cover to water cooler, but after thoroughly flushing
the supply line and connecting it to the fixture, turn on building water supply and check all connections for
leaks.
2. Air within the water cooler system or the structure supply piping will cause an irregular bubbler outlet stream
until purged out by incoming water. Covering the bubbler with a clean cup (or similar object) is recommended
when first activating water cooler to prevent excessive splashing. Depress the pushbutton until steady water
stream is achieved.
3. If water flow requires adjustment, insert a slotted narrow blade screwdriver through the hole centered on the
pushbutton to the flow regulator. Turning clockwise will increase flow and turning counterclockwise will
decrease flow.
4. Recheck all water and drain connections with water flowing through system.
5. With power still NOT connected, carefully manually rotate cooling fan to insure proper clearance and free fan
action.
6. Plug water cooler in to electrical outlet and make sure unit begins to function.
7. Assemble bottom cover to water cooler with screws furnished.
TROUBLE SHOOTING:
IMPORTANT: BEFORE MAKING ANY OF THE REPAIRS LISTED, MAKE SURE THE WATER COOLER IS
DISCONNECTED FROM THE ELECTRICAL SUPPLY AND THE WATER SUPPLY VALVE IS SHUT OFF.
1. Adjustments
a. Cartridge – The water flow can be adjusted through the pushbutton using a straight blade
screwdriver and turning clockwise to increase flow and counterclockwise to decrease flow.
b. Cold Water Thermostat – The water temperature can be adjusted using a slotted screwdriver
and turning clockwise to make colder and counterclockwise to make warmer.
c. Bubbler Stream – Bubbler can be rotated slightly to direct the stream backwards or forwards.
Adjust the stream to minimize splashing. Splashing may occur from bubbler stream if the unit
is not level. Shim lower mounting points, if necessary, to level cooler.
2. Compressor Does Not Run
a. Check the electrical receptacle for power and correct voltage. The incoming voltage
must be within 10% of the rated voltage on the serial nameplate.
b. The cold thermostat is accessible by removing the bottom access cover. If the cold
thermostat capillary bulb loses its charge or becomes kinked it will fail in the open position
causing a disruption of power to the compressor. Unplug the water cooler and using and
ohm meter check for continuity across the two electrical terminals on the thermostat. Install
a new thermostat if there is no continuity.
c. Check for loose wires within the compressor box. The incoming power leads must be
connected to the overload and relay.
d. If all components check positive for continuity then test the wiring harness plug for
continuity to see if there is a broken wire within the wiring harness insulation.
3. Compressor Runs – Water Is Warm
a. The most common cause for a water cooler to run without producing cold water is a loss
of refrigerant. The water cooler must be taken to a certified refrigerant technician for repairs.
b. Make sure the condenser fan motor is operative. The fan blade must turn freely to help
remove the heat of compression.
c. An incorrect refrigerant charge, restriction or defective compressor (not pumping) will also
cause the compressor to run without producing cold water. All these signs indicate a
problem within the refrigeration system and the water cooler must be checked by an
authorized service company.
4. Compressor Cycling On Overload Protector
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 5 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
a. A dirty condenser or a blocked fan will cause a high head pressure and frequent cycling of
the overload protector.
b. Check the incoming voltage to make sure it is within 10% of the serial nameplate rating.
c. A restriction or moisture in the system will also cause intermittent cycling. A certified
refrigeration mechanic should be contacted in this situation.
d. Change the overload or relay if defective.
5. Noisy Operation
a. Check to make sure the fan blade is rotating freely.
b. Make sure the water cooler is correctly mounted to the wall. Absence of the two lower
mounting bolts may cause excess noise and vibration.
c. Check the compressor mounting to make sure the pins and clips are not rattling. If the
compressor appears to be noisy internally, it must be replaced.
6. Restricted Or No Water Flow
a. Ensure water supply service stop valve is fully open.
b. Verify minimum 20 psig supply line flow pressure.
c. Check for twists or kinks in bubbler tubing.
d. Check the water inlet strainer. Sediment from the main supply can get trapped in the
screen along with installation materials such as pipe dope and flux. The screen should
be cleaned and checked on a regular basis and replace if needed.
NOTE: STRAINER SCREEN MUST BE IN PLACE FOR WATER TO FLOW.
e. The cartridge valve located in the water control assembly or bubbler can also become
clogged with foreign material. The cartridge valve can only be replaced and not repaired.
f. Check flow adjustment. See start up note #3.
g. The water cooler may also develop a freezing condition in which the water will become
frozen inside the evaporator coil. This indicates a refrigeration problem or thermostat
failure in which case the water cooler needs to be checked by a qualified technician.
CLEANING & MAINTENANCE GUIDE:
1. Motors have lifetime lubrication and do not require scheduled maintenance.
2. Excess dirt or poor ventilation will cause the compress` more frequently.
3. Periodically remove access panels and clean out in-line strainer.
4. Do NOT use harsh chemicals, abrasive or petroleum based cleaners. Use of these will void the Acorn warranty.
5. Exterior panels can be cleaned using mild household detergents or warm, soapy water. Extra care must be
used cleaning chrome plated items and mirror finished stainless steel. They can scratch easily and should only
be cleaned using a clean, soft cloth and mild soap with water or a mild glass cleaner.
CARTRIDGE REPLACEMENT/ STRAINER MAINTENANCE
Note: Use the universal maintenance tool to perform the following:
1. Strainer plug must be removed before cartridge replacement and strainer
maintenance (no need to turn the water off at the angle stop). Some residual water will drain
during plug removal.
2. Clean strainer as needed using clean water.
3. Cartridge replacement - insert diamond end of the universal tool into push button, rotate 90 degrees and pull
firmly to remove the button. Remove cartridge retaining nut . Remove and replace cartridge. When replacing
cartridge be sure to align the inlet and outlet ports on the cartridge with the ports in the valve body.
NOTE: STRAINER SCREEN MUST BE IN PLACE FOR WATER TO FLOW.
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 6 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
CARTRIDGE VALVE PARTS BREAKDOWN
1
2
5
4
ITEM
5
4
3
2
1
PART NUMBER
DESCRIPTION
7003-830-000
UNIVERSAL MAINTANANCE TOOL
7003-864-000
STRAINER FILTER SCREEN
7003-097-001
O-RING &STRAINER PLUG
7000-060-000 FLOW REGULATOR CARTRIDGE(05 GPMG)
7003-095-001
VALVE ASSEMBLY
3
Repairs must be made with Acorn Engineering parts only. Please order through your local representative
or distributor. The phone to locate your local representative is 1.800.591.9360
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 7 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
PUSH-IN FITTING INSTALLATION
NOTE: FITTINGS AND TUBE SHOULD BE KEPT
CLEAN, BAGGED AND UNDAMAGED PRIOR TO
INSTALLATION.
TO CUT TUBE:
Cut to fit length of 1/4” PE tubing and remove any burrs
or sharp edges. Ensure that the outside diameter is free
from score marks. Tube ends should be square.
INSERTING THE TUBE:
O-RING
1. Firmly and fully insert the tubing end into the push-in
fitting up to the tube stop located approximately ½”
deep.
O-RING
COLLET
TUBE STOP
COLLET
2. Pull on the fitted tubing to ensure it is secure. Tube
should not come free from the fitting. Water test the
connection assembly prior to leaving the site to ensure
there are no leaks.
COLLET
COLLET
DISCONNECTING THE TUBE:
To disconnect the tube from the fitting ensure that the
water line is depressurized. Push collet square towards
the push-in fitting body and hold. While holding the collet
in, pull on the PE tubing to remove from the push-in fitting.
COLLET
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 8 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
WATER COOLER PARTS BREAKDOWN DRAWING:
NOTE: See page 11 for table of part numbers corresponding to
drawing below.
1
2
3
4
5
6
32
8
7
11
5
11
9
Universal Maintenance Tool
-Button Removal
-Cartridge Retaining Nut
-Strainer Plug
-Removal of P.E. Tubing from
Push-in Fittings
12 13
10
17
8
27"
15 16
14
27
17
34"
15 16
19
18
24
25
23
NOTE:
29 Flow Restrictor Only Available
With Low Flow Bubbler.
20
22
26
21
15"
15 16
28
33
15"
15 16
29
28
30
32
29
31
30
31
Standard A172.8UBL series refrigerated ADA cooler shown. All 1/4" O.D. Plastic tubing 15 must be
insulated with 16 foam insulation.
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 9 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
SENSOR OPERATED WATER COOLER PARTS BREAKDOWN DRAWING:
NOTE: See page 11 for table of part numbers corresponding to drawing below.
1
2
3
4
5
6
32
8
7
11
5
11
9
12 13
10
17
8
Universal Maintenance Tool
-Button Removal
-Cartridge Retaining Nut
-Strainer Plug
-Removal of P.E. Tubing from
Push-in Fittings
27"
15 16
14
27
17
34"
15 16
19
18
24
25
23
NOTE:
29 Flow Restrictor Only Available
With Low Flow Bubbler.
20
22
26
15"
15 16
28
29
15"
15 16
21
33
44
38
39
30
32
31
34
29
43
42
38
28
36
39
35
41
38
40
39
37
Repairs must be made with Acorn Engineering parts only. Please order through your local representative
or distributor. The phone number to locate your local representative is 1.800.591.9360.
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 10 of 11
Date: 04/29/15
INSTALLATION, OPERATIONS & MAINTENANCE MANUAL
Please visit www.acorndrinkingfountains.com for most current specifications.
COOLER PARTS BREAKDOWN TABLE
NOTE: See previous page for fixture drawing corresponding to table of parts below.
ITEM # PART NUMBER
1
0124-032-000
2
7003-099-002
3
0124-021-000
7000-099-002
4
7000-012-001
7000-002-001
5
7000-006-000
6
7003-182-000
7
7003-183-199
8
7003-184-000
9
7003-181-000
7003-819-020
10
7003-825-199
11
7003-014-199
12
0124-050-000
13
1895-123-000
14
7003-120-000
15
2169-000-000
16
7012-055-000
17
7003-003-199
7003-302-000
18
7012-062-001
19
7003-350-000
20
7003-201-000
7012-801-000
21
7012-030-001
7012-802-000
22
7012-031-000
7012-803-000
23
7012-032-000
24
7003-250-000
7003-817-020
25
7003-823-299
7003-818-020
26
7003-824-299
27
7003-007-199
7003-816-020
7003-826-001
28
7003-029-020
7003-029-005
29
7003-093-001
30
7003-095-001
31
7003-099-000
32
7003-830-000
33
0124-031-000
34
7001-200-001
35
7003-027-199
36
2562-369-001
37
7001-202-199
38
0308-009-000
39
0331-023-000
40
0711-407-199
41
7003-028-199
42
7000-059-199
43
7003-023-199
44
7000-050-001
DESCRIPTION
#8 x 3/4" LG PHIL FLAT HD SELF TAPPING SCREW
BASIN TOP
#8 x 3/8" LONG ALLEN PAN HEAD SCREW
LOW-FLOW FLEXIBLE BUBBLER ASSEMBLY
STAINLESS STEEL BUBBLER ASSEMBLY
CHROME PLATED BRASS BUBBLER ASSEMBLY
FLAT DRAIN GASKET
DRAIN TAIL PIECE (SHORT)
DRAIN HOSE
7/8" SPRING HOSE CLAMP
DRAIN TAIL PIECE (LONG)
FILLER PLATE - GRANITE
FILLER PLATE - STAINLESS STEEL
HANGER BRACKET
#8 x 3/8" lg PHILLIPS PAN HEAD SCREW
1/4" OD x 3/8" OD PUSH-IN CONNECTION
EVAPORATOR ASSEMBLY
1/4" OD TUBING
TUBE INSLULATION
BACK PANEL
FAN MOTOR
FAN MOTOR - 220V
FAN BLADE
CONDENSER
COMPRESSOR
COMPRESSOR - 220V
START RELAY
START RELAY - 220V
START CAPACITOR
START CAPACITOR - 220V
COLD CONTROL
LEFT CABINET - GRANITE
LEFT CABINET - STAINLESS STEEL
RIGHT CABINET - GRANITE
RIGHT CABINET - STAINLESS STEEL
SUPPORT STRUT
APRON ASSEMBLY - GRANITE
APRON ASSEMBLY - STAINLESS STEEL
SENSOR OP APRON ASSEMBLY - GRANITE
SENSOR OP APRON ASSEMBLY - STAINLESS STEEL
FLOW RESTRICTOR - LOW-FLOW BUBBLER ONLY
VALVE ASSEMBLY
PUSH BUTTON
UNIVERSAL MAINTENANCE TOOL
#8 x 3/8 LNG SLOTTED HEX WASHER HD SCREW
SOLENOID/VALVE MOUNTING ASSEMBLY
SENSOR BRACKET, SENSOR OP
9VDC SENSOR
SENSOR SPACER
#8-32 NYLON INSERT LOCKNUT
#8 S/S FLAT WASHER
POWER SUPPLY , 240VDC
TRANSFORMER BRACKET
1-1/4" - 18 NORMALLY OPEN VALVE CAP
CARTRIDGE MTG BRACKET, SENSOR OP
VALVE CARTRIDGE ASSEMBLY
Repairs must be made with Acorn Engineering parts only. Please order through your local representative
or distributor. The phone number to locate your local representative is 1.800.591.9360.
7020-905-001
ACORN ENGINEERING FIELD SERVICE
TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863
Page 11 of 11
Date: 04/29/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising