BTC COMBO 5216IB User`s manual


Add to my manuals
24 Pages

advertisement

BTC COMBO 5216IB User`s manual | Manualzz

Dual Digital Storage Drive

COMBO 5216IB

User’s Manual

DANGER

VORSICHT

ATTENTION

C L A S S 1 L A S E R P R O D U C T

A P P A R E I L A L A S E R D E C L A S S E 1

L A S E R K L A S S E 1

L U O K A N 1 L A S E R L A I T E

P R O D U I T L A S E R

C A T E G O R I E 1

INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT

EXPOSURE TO BEAM

INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET

NICHT DEM STRAHL AUSSETSEN

RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.

EVITER TOUTE EXPOSITION AUX RAYONS.

Copyright Statement

It is a criminal offence, under applicable copyright laws, to make unauthorised copies of copyright-protected material, including computer programs, films, broadcasts and sound recordings. This equipment should not be used for such purposes.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FOR EUROPE

“The drive is in conformity with the EMC directive and low-voltage directive.”

Table of Contents

INTRODUCTION 1

S

YSTEM

R

EQUIREMENTS

P

ACKAGE

C

ONTENTS

2

2

INSTALLATION 3

H

OST

I

NTERFACE

C

ONNECTIONS

H ARDWARE I NSTALLATION

D RIVER I NSTALLATION

S OFTWARE I NSTALLATION

3

4

6

9

DVD R

EGION

C

ODE

10

OPERATION & CONNECTION 12

F

RONT

P

ANEL

12

R

EAR

V

IEW

14

TECHNICAL DATA 16

COMBO 5216IB

INTRODUCTION

Welcome to a multimedia world of CD-ReWritable technology, DVD-ROM capabilities and, memory card compatibility!

This compact and high-performance COMBO 5216IB frees up precious bay space and presents you as an IDE Combo (CD-RW+DVD ROM) Drive and a USB-connected card reader. It reads CDs of all types at maximum 52X speed, and DVD-ROMs at maximum 16X speed. For the writing ability, it writes to CD-Rs at up to 52X speed, and to CD-RWs at up to 24X speed.

Other than that, the built-in 7 in 1 card reader which offers read-write ability of 7 memory card types simplifies the process of exchanging data between digital cameras, voice recorders, PDAs, MP3s… and your computer.

With this multi-functional solution and the bundled software package, you can view, archive, or write files/photos/video/music directly from the drive and enjoy the fascinating digital and DVD entertainment on your desktop.

Here are some important features of this Combo Drive:

♦ Easy installation with Combo drive of EIDE and card reader of

USB 2.0 interface (on board connection)

♦ 8X, 16X, 24X, 32X, 40X, 48X and 52X writing speed on CD-R media

♦ 4X, 10X, 12X, 16X and 24X writing speed on CD-RW media

♦ Adopts “MTKSuperLink” to prevent Buffer Underrun

♦ Supports writing modes of TAO, DAO, SAO and packet writing

♦ Supports MultiRead function

♦ Smooth DVD playback of high resolution

♦ Convenient connection with A-Type USB Extension Port on the front panel

1

COMBO 5216IB

♦ Four-slot integration of the card reader works with CompactFlash,

MicroDrive, Memory Stick, Memory Stick Pro, MultiMediaCard,

Secure Digital, and SmartMedia

System Requirements

For IBM compatible PCs, the system requirements recommended are as follows:

♦ Pentium II, Celeron 400MHz or above with at least 64MB of memory

♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.)

♦ IDE host interface supporting ATAPI MMC command & USB host interface (if you don’t have USB on-board connection)

♦ Microsoft Windows 98SE/2000/ME/XP

Package Contents

The package contains the following items:

♦ Dual Digital Storage Drive, COMBO 5216IB

♦ Audio cable

♦ Application software discs x 2

♦ Quick Installation Guide

2

COMBO 5216IB

INSTALLATION

Host Interface Connections

Most current motherboard models have two IDE ports (primary and secondary), which can connect two IDE cables. Two IDE cables allow you to connect up to four devices, but it is recommended that you separate IDE ports for your hard disk and your Combo Drive. This will ensure that your hard disk’s performance and speed won’t be affected by having the drive on the same cable.

Jumper Setting

On the rear panel of this drive, you will find three pairs of jumpers: CS

(CSEL), SL (Slave) and MA (Master). Use the jumper cap to set the device to CS, SL or MA mode corresponding to your PC configuration. If you connect only one device on the IDE cable, you can set the jumper as

“MASTER” or “SLAVE”.

Master

Slave

Cable Select

If you connect two devices on the same cable, set different jumper for each device (one as “MASTER”, and the other one as “SLAVE”). The same rule applies to the connection of having your hard disk and another device on the same cable.

3

COMBO 5216IB

Cable Select

Slave

Master

Jumper

The system might not detect the drive if there is conflict or mistake with the jumper setting.

Hardware Installation

1. Turn off the power to your computer system.

2. Disconnect the power cord and all cables from the back of your computer, and then remove the cover of the computer.

3. Insert the drive into one of the vacant 5.25" drive bays and secure it to your PC with all four mounting screws.

4. Connect one end of the 40-pin IDE cable to the IDE connector of this drive and the other end to the IDE port on your motherboard. Also, connect the power supply cable to the back of the drive.

4

Audio Out Power In

Digital

Audio Output red edge

Make sure to align and connect the red-edge of the IDE Cable to Pin 1 on the drive.

COMBO 5216IB

5. If you have a sound card that can be connected to the drive, you can also connect the drive (as Audio-Out) and the sound card (as Audioin) with a 4-pin audio cable.

If your mainboad is integrated with built-in sound system, plug the 4pin audio cable into the CD-IN connector on the motherboard as

Audio-in.

6. Connect the USB cable at the back of the drive to the USB header on the computer’s motherboard. The red wire of the cable needs to be plugged into Pin 1 on the board.

This drive supports USB 2.0

and if you connect to USB 1.1 connector, only transfer rate of USB 1.1 will be available.

IDE

RED WIRE

USB

RED WIRE

MOTHER

BOARD

Signal

Red/Vcc

White/D-

Green/D+

Black/Ground

Braided Shield Ground

Error-Proof Pin

Pin#

1 / 6

2 / 7

3 / 8

4 / 9

5

10

USB Header

If the connection is correct, the lower right LED on the front panel will light green.

7. Re-attach the cover of the computer, and reconnect the power cord and all cables to the computer.

5

COMBO 5216IB

Driver Installation

For the Combo Drive

For the Combo Drive itself, it’s an IDE device supporting Plug & Play and

Windows 98SE/ME/2000/XP can automatically detect the drive and load the appropriate driver.

For the Card Reader

Windows 98SE/2000

If you are using Window 98SE or 2000, please install the provided driver.

1. Insert the application disc.

2. Select:\Card Reader Driver

USB Software Installer for 4icons.exe”, and follow the onscreen instructions:

6

COMBO 5216IB

7

COMBO 5216IB

Windows ME/XP

Since Windows ME and XP already have USB Mass Storage support, the card reader can be detected and work fine without installing driver.

However, we recommend that you install the provided driver to have more explicit operation status of the card reader, as described below.

For Windows XP users, please upgrade to Service Pack 1.

After the driver installation, 4 extra icons with different card type indicated will show in Device Manager/My computer. And then you can use each slot of the card reader for file archiving/recording.

While the card reader is reading data of memory cards, the upper right LED on the front panel flashes red.

8

Software Installation

COMBO 5216IB

Burning Software

The bundled recording software gives you the complete solution for making audio/data CDs. With the user-friendly interface, it guides you through the creation and backup of files/photos/video/music from your computer to a recordable compact disc. Combining of the card reader capabilities, no matter you are a novice or an experienced user; you can enrich your digital life with this best recording tool.

DVD Playback Software

The DVD playback software comes with leading video and audio technologies to deliver the highest sound and visual effect possible on the

PC. Meanwhile, it offers feature-rich navigation controls for an interactive and tailored DVD movie viewing experience. You can enjoy the wide range of educational and entertaining DVD titles with theater quality.

Windows Environment

1. Insert the application CD and the installation program will run automatically. Then follow the on-screen procedures.

Or

2. Run:\setup.exe on the application CD.

9

COMBO 5216IB

DVD Region Code

Region Playback Control Management

All DVD Video Playback systems have “Region Playback Control” management (RPC) which is required by Hollywood movie industry and defined by DVD Forum. This includes DVD-Video players and PC systems with DVD-Video capability. You can only play DVD-Video discs with the same region code as your DVD-Video Playback system.

As for DVD-ROM drives, one kind of the DVD-Video Playback system, there are 2 types:

RPC Phase 1 (as RPC1): RPC1 drives do not have built-in hardware support for region management. DVD-ROM drives of this kind don’t play a part in controlling the playback region. It solely depends on the decoder.

RPC Phase 2 (as RPC2): RPC2 drives maintain the region change count information in hardware, and in general, the region of such drives can be changed up to 5 times by the end users under some software decoder (e.g.

PowerDVD).

And referring to the region codes, there are 6 regions worldwide, and normally, there is a region code mark on the package of DVD titles. :

Region 1: Canada, US

Region 2: Japan, Europe, South Africa, and Middle East (including

Egypt)

Region 3: Southeast Asia and East Asia (including Hong Kong)

Region 4: Australia, New Zealand, Pacific Islands, Central America,

Mexico, South America, and the Caribbean

Region 5: Eastern Europe, Indian subcontinent, Africa, North Korea, and Mongolia

Region 6: China

10

COMBO 5216IB

About This Dual Digital Storage Drive

This drive is also a RPC2 DVD-ROM drive and according to DVD-Forum,

PC chip must be designed into DVD-ROM drives to record how many times a user has changed the region code. The first region code will depend on the DVD title you play and you are allowed to modify the region code 5 times (including the initial one). After the fifth alteration, the region code will be locked and only those DVD titles of the same region code could be played afterwards, so set the code carefully.

11

COMBO 5216IB

OPERATION & CONNECTION

Front Panel

1. A-Type USB Extension Port

This USB port is Plug-and-Play Ready. Just plug your USB device and the computer will detect automatically.

2. Close/Eject Button

This button opens and closes the disc tray. If the tray is closed, pressing the button will eject it.

3. LED Indicator (the Combo Drive)

While the tray goes in/out, the LED lights green and it’s off when the drive is ready.

The LED flashes “green” while verifying or reading a disc and flashes

red” while writing data.

4. Disc Tray

Place the disc in the tray here, and then press the Close/Eject button or lightly push the tray to close it.

12

COMBO 5216IB

5. Emergency Eject Hole

When the Close/Eject button doesn’t work properly and the disc tray can’t be opened, you can insert a paper clip or a small rod into this hole for manual ejection. Please make sure to power off the system before you do that.

6. Slot for Memory Stick (MS)/Memory Stick Pro (MS Pro)

7. Slot for Secure Digital (SD)/MultiMediaCard (MMC)

8. Slot for Compact Flash (CF) Type I, II/MicroDrive

9. Slot for Smart Media

10. LED Indicator (the Card Reader)

When the data of the memory card is being accessed, the LED flashes red.

11. LED Indicator (the Card Reader)

Once the USB cable is correctly connected, this LED will light green, which means the card slots are ready to use.

Note: The design of front panel is subject to change without notice.

13

COMBO 5216IB

Rear View

2 3 4 5

6

1. Digital Audio Output Connector

If your sound card has a digital audio IEC958 format connector, you can connect it to this digital audio output connector with a 2-pin audio cable.

2. Analog Audio Output Connector

This connector allows you to connect the drive to your sound card with a 4-pin audio cable.

3. Device Configuration Jumper

Set the jumper to Master, Slave or Cable Select according to your system configuration.

4. IDE Interface Connector

Plug one end of the 40-pin IDE cable here to join the 40-pin IDE connector on the motherboard. The red-edge of the IDE cable must be connected to Pin 1 of each connector.

5. Power Supply Connector

By plugging the computer’s power supply cable here, you can connect the drive and your computer system.

14

COMBO 5216IB

6. USB Cable

Connect the USB cable to the USB connector on the motherboard.

The red wire of the cable needs to be plugged into Pin 1 on the board.

15

COMBO 5216IB

TECHNICAL DATA

Interface

Form factor

Writing speed

Writing modes

Digital Media

Transfer rate

Combo Drive

Card Reader

Access time (⅓ stroke)

Combo Drive: EIDE

Card Reader: USB 2.0

5.25" Half Height

CD-R: 8X/16X/24X/32X/40X/48X/52X

CD-RW: 4X/10X/12X/16X/24X

TAO (Track at once), DAO (Disc

At Once), SAO (Session at once),

Multi-session, Packet Writing

CompactFlash, MicroDrive, Memory

Stick, Memory Stick Pro, SmartMedia,

MultiMediaCard, and Secure Digital

Read:

CD-ROM: 7800KB/sec (up to 52X)

CD-RW: 4800KB/sec (up to 32X)

DVD: 21632KB/sec (up to 16X)

Write:

CD-R: 7800KB/sec (up to 52X)

CD-RW: 3600KB/sec (up to 24X)

480Mb/s (USB 2.0)

CD/DVD: 110/120ms

16

Disc Format Supported

CD-DA

CD-ROM

CD-ROM XA

CD-EXTRA

Video CD

Photo CD

CD-I

CD-TEXT

DVD-ROM (DVD-5, DVD-9,

DVD-10, DVD-18)

DVD+R, DVD+RW

DVD-R, DVD-RW

Disc loading

Audio output level

Power

COMBO 5216IB

Write Read

2MB

Tray (motorised), Dust Sealed

Line out = 0.6 ± 10%Vrms

5 VDC & 12VDC

Card Reader power directly from computer power supply through USB connection

Dimensions

Height

Width

Depth

Weight

41.8 ± 0.2 mm

148.6 ± 0.2 mm

193.3 ± 0.3mm

1 kg

17

COMBO 5216IB

Environment

Temperature

Operating

Non-operating

Disc

Humidity

Operating

Non-operating

Disc Size

Disc Data Capacity

5°C to 45°C

-20°C to 45°C

8% ~ 80%RH

5% ~ 95%RH

80mm and 120mm discs

DVD-ROM: Single layer – 4.7GB

Dual layer – 8.5GB (one side)

CD-ROM: 74min – 650MB – Mode 1

80min – 700MB – Mode 1

18

3100552200

Version 1.0

Jan. 2004

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Frequently Answers and Questions

What are the minimum system requirements to run the BTC COMBO 5216IB?
Pentium II, Celeron 400MHz or above with at least 64MB of memory, fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended), IDE host interface supporting ATAPI MMC command & USB host interface (if you don't have USB on-board connection), Microsoft Windows 98SE/2000/ME/XP.
What is the maximum speed at which the drive can read and write different types of media?
Reads CDs at maximum 52X speed, DVD-ROMs at maximum 16X speed. Writes to CD-Rs at up to 52X speed, and to CD-RWs at up to 24X speed.
What types of memory cards can the built-in card reader work with?
CompactFlash, MicroDrive, Memory Stick, Memory Stick Pro, MultiMediaCard, Secure Digital, and SmartMedia.
Which Windows operating systems are supported?
Windows 98SE/2000/ME/XP.
How do I connect the drive to my computer?
Connect one end of the 40-pin IDE cable to the IDE connector of the drive and the other end to the IDE port on your motherboard. Also, connect the power supply cable to the back of the drive, and if you have a sound card, use a 4-pin audio cable to connect the drive (as Audio-Out) and the sound card (as Audio-in).
What software is included with the drive?
Burning software for creating audio/data CDs and DVD playback software for an interactive DVD movie viewing experience.

advertisement