6 Plug-In DA&C Cards
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Plug-In DA&C Cards
6
Data Acquisition and Control Tutorial & Software
Data Acquisition and Control Card Selection Guide
6-2
6-4
PCI-1710/1710L/ 1710HG/1710HGL
PCI-1711/1711L
PCI-1712/1712L
PCI-1716/1716L
PCI-1718HDU/PCI-1718HGU (New)
PCI-1741U (New)
PCI-1747U (New)
100 kS/s, 12-bit, (High-gain), PCI-bus Multifunction Card
100 kS/s, 12-bit, 16-ch S.E. Inputs Low-cost Multifunction Card
1 MS/s, 12-bit, 16-ch High-speed Multifunction Card
250 kS/s, 16-bit, 16-ch High-resolution Multifunction Card
12-bit Multifunction DAS Card for PCI Bus
16-bit, 200kS/s High-Resolution Multifunction Card
250 kS/s 16-bit, 64-ch Analog Inputs Card
6-10
6-12
6-14
6-16
6-18
6-20
6-22
PCI-1713
PCI-1714/1714UL (New)
100 kS/s, 12-bit, 32-channel Isolated Analog Input Card
30 MS/s Simultaneous 4-ch Analog Input Card
6-24
6-25
PCI-1720/1720U (New)
PCI-1721
PCI-1723
PCI-1724U
PCI-1727U (New)
4-ch Isolated Analog Output Card
12-bit, 4-ch Advanced Analog Output Card
12-bit, 8-ch Isolated Analog Output Card
14-bit, 32-ch Analog Output Card
12-ch D/A Output Card
6-26
6-27
6-28
6-29
6-30
PCI-1751/1751U (New)
PCI-1753/1753E
PCI-1755
48-bit Digital I/O and Counter Card
96/192-bit Digital I/O Card
80 MB/s Ultra high-speed 32-ch Digital I/O Card
6-31
6-32
6-33
PCI-1730
PCI-1733
PCI-1734
PCI-1752
PCI-1754
PCI-1756
PCI-1758UDI/ PCI-1758UDO (New)
PCI-1757UP
PCI-1736UP (New)
PCI-1763UP
PCI-1750
PCI-1761
PCI-1760/1760U (New)
PCI-1762
32-ch Isolated Digital I/O Card
32-ch Isolated Digital Input Card
32-ch Isolated Digital Output Card
64-ch Isolated Digital Output Card
64-ch Isolated Digital Input Card
64-ch Isolated Digital I/O Card
128-ch Isolated Digital I/O Card
12-bit Multifunction DAS Card for PCI Bus
32-ch Isolated Digital IO Low-profile PCI Card
8-ch Relay and 8-ch IDI Low-profile PCI Card
32-ch Isolated Digital I/O and Counter Card
8-ch Relay Actuator and 8-ch Isolated D/I Card
8-ch Relay Actuator and Isolated D/I Card
16-ch Relay Actuator and 16-ch Isolated D/I Card
6-34
6-34
6-34
6-36
6-36
6-36
6-38
6-40
6-41
6-42
6-43
6-44
6-45
6-46
PCI-1780
8-ch Counter/ Timer Card
6-47
PCL-711B/S
PCL-812PG
PCL-818 Series
PCL-818L/LS/H
PCL-818HD/HG
Analog and Digital I/O Card
MultiLab Analog and Digital I/O Card
High-performance Multifunction Card
40 kS/s Multifunction Card
High-performance Multifunction Card
6-48
6-49
6-50
6-51
6-52
PCL-813B
32-ch S.E. Isolated A/D Card
6-53
PCL-726
PCL-727
PCL-728
6-ch D/A Output Card
12-ch D/A Output Card
Isolated 2-ch D/A Output Card
6-54
6-54
6-54
PCL-720+
PCL-722
PCL-724
PCL-731
Digital I/O and Counter Card
144-bit Digital I/O Card
24-bit Digital I/O Card
48-bit Digital I/O Card
6-55
6-56
6-56
6-56
PCL-725
PCL-735
PCL-730
PCL-733
PCL-734
PCL-836
Relay Actuator and Isolated D/I Card
12-ch Relay Actuator Card Counter Card
32-ch Isolated Digital I/O Card
32-ch Isolated Digital Input Card
32-ch Isolated Digital Output Card
6-ch Counter/Timer Card
6-57
6-57
6-58
6-58
6-58
6-60
PCM-3712
PCM-3718H/HG/PCM-3718HO (New)
PCM-3724
PCM-3725
PCM-3730
PCM-3780 (New)
12-bit, 2-ch Analog Output Module
100 kS/s, 12-bit, 16-ch Multi-function Module
48-ch Digital I/O Module
8-ch Isolated Digital Input and 8-ch Relay Output Module
16-ch Isolated Digital I/O Module
2-ch Counter/Timer with 24 ch TTL DIO Module
6-61
6-61
6-61
6-62
6-62
6-62
PCI-1670
PCI-1671 (New)
GPIB interface PCI card
High-Performance IEEE-488.2 Interface for PCI-Bus Computers
6-63
6-64
USB-4711 (New)
USB-4716 (New)
USB-4718 (New)
ISA-Compatible PCI Cards
100 kS/s, 12-bit USB Multifunction Module
100 kS/s, 16-bit USB Multifunction module
8-ch Thermocouple Input Module
6~65
6~66
6~67
6~68
PCI-bus Data Acquisition and Control Cards
PCI / Universal PCI Multifunction Cards
PCI / Universal PCI Analog Input Cards
PCI / Universal PCI Analog Output Cards
PCI / Universal PCI Non-Isolated Digital I/O Cards
PCI / Universal PCI Isolated Digital I/O Cards
Counter Cards
ISA-Bus Data Acquisition and Control Cards
Multifunction Cards
Analog Input Cards
Analog Output Cards
Non-Isolated Digital I/O Cards
Isolated Digital I/O Cards
PC/104 I/O Modules
GPIB interface series
Portable Data Acquisition Modules
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-2
Data Acquisition and Control
Tutorial
PC-based Data Acquisition System
Overview
In the last few years, industrial PC I/O interface products have become increasingly reliable,
accurate and affordable. Because of this, PC-based data acquisition and control systems
are now widely used in industrial and laboratory applications such as: monitoring, control,
data acquisition and automated testing.
Selecting and building a DA&C (Data Acquisition and Control) system that actually does
what you want it to do requires some knowledge of electrical and computer engineering.
This tutorial gives a brief introduction to what DA&C systems do and how to configure
them. It covers:
 Transducers and actuators
Signal Conditioning
Signal conditioning circuits improve the quality of signals generated by transducers before
they are converted into digital signals by the PC's data-acquisition hardware. Examples
of signal conditioning are signal scaling, amplification, linearization, cold-junction
compensation, filtering, attenuation, excitation, common-mode rejection, and so on.
One of the most common signal conditioning functions is amplification. For maximum
resolution, the voltage range of the input signals should be approximately equal to the
maximum input range of the A/D converter. Amplification expands the range of the
transducer signals so that they match the input range of the A/D converter. For example,
a x10 amplifier maps transducer signals that range from 0 to 1 V into the range 0 to 10
V before they go into the A/D converter.
 Signal conditioning
 Data acquisition and control hardware
 Getting Started
 Computer systems software
Transducers and Actuators
A transducer converts temperature, pressure, level, length, position, etc. into voltage,
current, frequency, pulses or other signals.
Thermocouples, thermistors and resistance temperature detectors (RTDs) are common
transducers for temperature measurements. Other types of transducers include flow
sensors, pressure sensors, strain gauges, load cells and LVDTs, which measure flow
rate, pressure variances, force or displacement.
An actuator is a device that activates process control equipment by using pneumatic,
hydraulic or electrical power. For example, a valve actuator can open and close a valve
to control fluid rates.
Using digital I/O and SSRs to open and close a valve
The layout of a typical PC-based data acquisition system
Plug-in DA&C Cards
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
DA&C Tutorial
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Data Acquisition & Control Hardware
Getting Started
Data acquisition and control hardware generally performs one or more of the following
functions: analog input, analog output, digital input, digital output and counter/timer
functions. This section will discuss each function and list some considerations that are
important when you select a data acquisition and control system.
Advantech: The source for what you need
Analog Inputs (A/D)
Step 1: Know your fundamental goal
Analog to digital (A/D) conversion changes analog voltage or current levels into digital
information. The conversion is necessary to enable a computer to process or store the
signals.
Decide whether your DA&C system will be used primarily for measurement, monitoring,
control, or analysis. Know the data requirements of your process, and know the number
of data collection points in your system. Know the required data collection speed, the
FPM
sampling rate, the type of measurement, the voltage or current being produced, the desired
accuracy and the output resolution at each data collection point. Finally, know the timing
of events in your system, and any special environmental conditions that exist.
Software
Advantech manufactures data acquisition hardware and software for measurement,
monitoring and applications control. The following guide is provided to help you choose IPPC
components for your data acquisition system.
TPC
ATM & AWS
Step 2: Hardware selection
Select the hardware required to achieve your fundamental goal. Advantech provides
plug-in boards for Analog-to-Digital, Digital-to-Analog,Digital I/O, RS-232 or RS-485 DA&C
needs. Both ISA and PCI bus products are available. Your hardware selection should be
based on five major criteria:
1. Number and types of channels
The most significant criteria when selecting A/D hardware are:
cPCI
2. Differential or single-ended inputs
1. Number of input channels
3. Resolution
2. Single-ended or differential input signals
ADAM-3000
4. Speed
3. Sampling rate (in samples per second)
5. Software compatibility with hardware
4. Resolution (usually measured in bits of resolution)
Step 3: Accessory selection
5. Input range (specified in full-scale volts)
6. Noise and nonlinearity
Most applications require additional accessories which are available as separate items.
These include:
Analog Outputs (D/A)
1. Expansion peripherals to add channels to your system
The opposite of analog to digital conversion is digital to analog (D/A) conversion. This
operation converts digital information into analog voltage or current. D/A devices allow
a computer to control real-world events.
2. Cables, signal conditioners and external boxes such as screw terminals or BNC
accessories
ICOM
eConnectivity
Step 4: Software selection
More than any other single factor, software will determine your system start-up time, as
well as its effectiveness, suitability for your application, and ease of modification.
Three major criteria should determine the choice of software:
1. Operating system used
2. User programming expertise
UNO
ADAM-4000
3. Software compatibility with hardware
ADAM-5000
Analog output signals may directly control process equipment. The process can give
feedback in the form of analog input signals. This is referred to as a closed loop control
system with PID control. Analog outputs can also be used to generate waveforms. In this
case, the device behaves as a function generator.
ADAM-6000
Digital Inputs and Outputs
Digital input/output functions are useful in applications such as contact closure and switch
status monitoring, industrial On/Off control and digital communications.
ADAM-8000
Counter/timer
BAS
A counter/timer can be used for event counting, flowmeter monitoring, frequency counting,
pulse width measurement, time period measurement, and so on.
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Motion Control
Last updated : January 2005
6-3
Bus
PCI
Multifunction
Category
Model
General
Spec.
Analog Input
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-4
Data Acquisition and
Control Cards
PCI-1710/1710L
PCI-1710HG/HGL PCI-1711/1711L PCI1712/1712L PCI-1716/1716L
PCI-1718HDU/HGU
PCI-1741U
12 bits
12 bits
16 bits
12 bits
16 bits
16 SE/8 Diff.
16 SE
16 SE/8 Diff.
16 SE/8 Diff.
16 SE/8 Diff.
16 SE/8 Diff.
4K samples
100 kS/s
1K samples
100 kS/s
1K samples
1 MS/s
1K samples
250 kS/s
4K samples
100 kS/s
1K samples
200 kS/s






Resolution
12 bits
12 bits
Channels
16 SE/8 Diff.
Onboard FIFO
Sampling Rate
Auto Channel
Scanning
4K samples
100 kS/s

0 ~ 10, 0 ~ 5,
0 ~ 2.5, 0 ~ 1.25
(PCI-1718HDU)
0 ~ 10, 0 ~ 5,
0~10, 0~1, 0~0.1,
0 ~ 2.5, 0 ~ 1.25
0~0.01
(PCI-1718HGU)
±10, 5, 2.5, 1.25,
0.625 (PCI-1718HDU)
±10, 5, 2.5, 1.25,
±10, 5, 1, 0.5, 0.1,
0.625
0.05, 0.01, 0.005
(PCI-1718HGU)
Unipolar Inputs
(V)
0 ~ 10, 0 ~ 5,
0 ~ 2.5, 0 ~ 1.25
0 ~ 10, 0 ~ 1,
0 ~ 0.1, 0 ~ 0.01
-
0 ~ 10, 0 ~ 5,
0 ~ 2.5, 0 ~ 1.25
0 ~ 10, 0 ~ 5,
0 ~ 2.5, 0 ~ 1.25
Bipolar Inputs (V)
±10, 5, 2.5, 1.25,
0.625
±10, 5, 1, 0.5, 0.1,
0.05, 0.01, 0.005
±10, 5, 2.5, 1.25,
0.625
±10, 5, 2.5, 1.25,
0.625
±10, 5, 2.5, 1.25,
0.625






-


















DMA
-
-
-
Bus-mastering
Bus-mastering
-
-
Resolution
12 bits
12 bits
12 bits
12 bits
16 bits
12 bits
16 bits
Number of
Channels
2
(PCI-1710 only)
2
(PCI-1710HG only)
2
(PCI-1711 only)
2
(PCI-1712 only)
2
(PCI-1716 only)
1
-
On-board FIFO
-
-
-
32K samples
-
-
-
Output Range (V)
0 ~ 5, 0 ~ 10
0 ~ 5, 0 ~ 10
0 ~ 5, 0 ~ 10
0 ~ 5, 0 ~ 10,
±5, ±10
0 ~ 5, 0 ~ 10,
±5, ±10
0 ~ 5, 0 ~ 10
-5~5V, -10~10V
Throughput
38 kS/s Typical**
38 kS/s Typical**
38 kS/s Typical**
1 MS/s
16
16
1
16-bit
10 MHz

175 x 100
16
16
1
16-bit
10 MHz

175 x 100
16
16
1
16-bit
10 MHz
175 x 100

Connector
68-pin SCSI-II
68-pin SCSI-II
Windows® 98/2000/XP DLL Driver
Windows® 98/2000/XP Test Utility
VC++, VB & Delphi Examples
Advantech ActiveDAQ
LabView® I/O Drivers
(Ver.6i and 7.0)
MathWorks
MATLAB & Simulink
Data Acquisition Tool Box 2.5.1
Page










Input Ranges
Trigger Mode
Data Transfer
Mode
Configurable
Per-Channel
Pacer/Software/
External Pulse
Analog Slope
Pretrigger
Post-trigger
About-trigger
Software
Analog Output
DMA Transfer
Input Channels
Digital I/O
Output Channels
Channels
Timer/Counter
Resolution
Time Base
Isolation Voltage
Auto Calibration
BoardID™ Switch
Dimensions (mm)
6-10
* Note: SS = Single DMA channel, Single A/D channel scan
Plug-in DA&C Cards
3
16-bit
10 MHz

175 x 100
200 kS/s
Typical**
16
1
16-bit
10 MHz


175 x 100
68-pin SCSI-II
68-pin SCSI-II
68-pin SCSI-II
DB-37
68-pin SCSI-II





























-
-
-
6-10
6-12
6-14
6-16
6-18
6-20
16 (mixed)
SM = Single DMA channel, Multiple A/D channel scan
16
16
1
16-bit
10 MHz

175 x 100
200 kS/s
Typical**
16
16
1
16-bit
10 MHz


175 x 100
100 kS/s Typical**
DM = Dual DMA channel, Multiple A/D channel scan
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Selection Guide
PCI
ISA
AI
PCI-1713
PCI-1714
PCI-1747U
12 bits
32 SE/16 Diff.
(Isolation)
4K samples
100 kS/s
12 bits
16 bits
PCI-1720/
1720U
-
4 SE
64 SE/32 Diff.
32 K samples
30 MS/s

0 ~ 10, 0 ~ 5,
0 ~ 2.5,
0 ~ 1.25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Multifunction
AO
PCI-1721
PCI-1723
PCI-1724
PCI-1727U
PCL-711B/S
PCL-812PG
PCL-818L/LS
-
-
-
-
12 bits
12 bits
12 bits
-
-
-
-
-
8 SE
16 SE
16 SE/8 Diff
1K samples
250 kS/s
-
-
-
-
-
25 kS/s
30 kS/s
40 kS/s


-
-
-
-
-
-
-

-
0 ~ 10, 0 ~ 5,
0 ~ 2.5,
0 ~ 1.25
-
-
-
-
-
-
-
-
IPPC
TPC
FPM
ATM & AWS
±10, 5, 2.5,
1.25, 0.625
±5, 2.5, 1, 0.5

±5, 2.5, 1.25,
0.625, 0.3125
±10, 5, 2.5,
1.25, 0.625,
0.3125
±10, 5, 2.5,
1.25, 0.625
-



-
-



cPCI
-
-
-



ADAM-3000
-
-
-
-
-
SS*
SM*
12 bits
4
(Waveform
Output)
1K samples
0 ~ 5, 0 ~ 10,
±5, ±10,
0 ~ 20 mA,
4 ~ 20 mA
10 MHz max.
update rate
Bus-mastering
16 bits
14 bits
12 bits
12 bits
12 bits
8
32
14 bits
12
1
2
1
-
-
-
-
-
-
-10 ~ 10
0 ~ 20 mA,
4 ~ 20 mA
±10, 0 ~ 20 mA
0~5, 0~10
±5, 4~20 mA
0 ~ 5, 0 ~ 10
0 ~ 5, 0 ~ 10
0 ~ 5, 0 ~ 10
15 kS/s
Typical**
-
15 kS/s
Typical**
-
16
16
-
1
16-bit
10 MHz


175 x 100


175 x 100

175 x 100
30 kS/s
Typical**
16
16
2 MHz
175 x 100
30 kS/s
Typical**
16
16
1
16-bit
2 MHz
185 x 100
30 kS/s
Typical**
16
16
1
16-bit
10 MHz
155 x 100
2 x 20-pin
2 x 20-pin
DB-37












±10, 5, 2.5,
1.25, 0.625
-


-
-
-
-



-
-
-







-
-
-
Bus-mastering
Busmastering
-
-
-
-
12 bits
4
(Isolation)
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10 MHz
2,500 VDC
175 x 100
1
8-bit
60 MHz


175 x 100
16-bit
10 MHz


175 x 100
0 ~ 5, 0 ~ 10,
±5, ±10,
0 ~ 20 mA,
4 ~ 20 mA
15 kS/s
Typical**
10 MHz
2,500 VDC
175 x 100
DB-37
4 BNC
68-pin SCSI-II
DB-37
68-pin SCSI-II
68-pin SCSI-II
DB-62




























16
16

175 x 100
2 x 20-pin,
DB-37
















-
-

-
-
-
-



6-24
6-25
6-22
6-26
6-27
6-28
6-29
6-30
6-48
6-49
6-51
-
-
DA&C
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
** Note: System-dependent
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-5
Bus
ISA
Category
Multifunction
Model
General
Spec.
Analog Input
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-6
Data Acquisition and
Control Cards
Input Ranges
AI
PCL-818HG
PCL-813B
PCL-726
PCL-727
PCL-728
Resolution
12 bits
12 bits
12 bits
-
-
-
Number of
Channels
16 SE/8 Diff
16 SE/8 Diff
32 SE
-
-
-
Onboard FIFO
1K samples
1K samples
-
-
-
-
Sampling Rate
100 kS/s
100 kS/s
25 kS/s
-
-
-
Auto Channel
Scanning


-
-
-
-
Unipolar Inputs
(V)
0 ~ 10, 0 ~ 5,
0 ~ 2.5, 0 ~ 1.25
0 ~ 10, 0 ~ 1,
0 ~ 0.1, 0 ~ 0.01
0 ~ 10, 0 ~ 5,
0 ~ 2.5, 0 ~ 1.25
-
-
-
Bipolar Inputs (V)
±10, 5, 2.5, 1.25,
0.625
±10, 5, 1, 0.5, 0.1,
0.05, 0.01, 0.005
±10, 5, 2.5, 1.25,
0.625
-
-
-
Configurable
Per-Channel



-
-
-
Pacer/Software/
External Pulse


Software only
-
-
-
Analog Slope
-
-
-
-
-
-
Pretrigger
-
-
-
-
-
-
Post-trigger
-
-
-
-
-
-
About-trigger
-
-
-
-
-
-
Software


Software only
-
-
-
DMA
SM*
SM*
-
-
-
-
Resolution
12 bits
12 bits
-
12 bits
12 bits
12 bits
Number of
Channels
1
1
-
6
12
2 (Isolation)
On-board FIFO
-
-
-
-
-
-
-0 ~ 5,
0 ~ 10, ±5,
4 ~ 20 mA
0 ~ 5, 0 ~ 10, ±5, ±10,
0 ~ 20 mA, 4 ~ 20 mA
Trigger Mode
Data Transfer
Mode
Analog Output
Digital I/O
AO
PCL-818HD
Output Range (V)
0 ~ 5, 0 ~ 10
0 ~ 5, 0 ~ 10
-
0 ~ 5,
0 ~ 10, ±5,
±10, 4 ~ 20 mA
Throughput
30 kS/s Typical**
30 kS/s Typical**
-
15 kS/s Typical**
15 kS/s Typical**
17 kS/s Typical**
DMA Transfer
-
-
-
-
-
-
Input Channels
16
16
-
16
16
-
Output Channels
16
16
-
16
16
-
Number of
Channels
1
1
-
-
-
-
Timer/Counter
Resolution
16-bit
16-bit
-
-
-
Time Base
10 MHz
10 MHz
-
-
-
-
Isolation Voltage
-
-
500 VDC min
-
-
500 VDC
-
Auto Calibration
-
-
-
-
-
BoardID™ Switch
-
-
-
-
-
-
Dimensions (mm)
185 x 100
185 x 100
219 x 100
337 x 112
337 x 112
185 x 120
Connector
DB37
DB37
DB37
4 x 20-pin
2 x 20-pin, DB37
2 x DB9
Windows® 95/98/ME/2000/XP DLL Driver






Windows® 95/98/ME/2000/XP Test Utility






VC++, VB & Delphi Examples






Advantech ActiveDAQ






LabView® I/O Drivers
(Ver.6i and 7.0)






MathWorks
MATLAB & Simulink
Data Acquisition Tool Box 2.5.1






Page
6-52
6-52
6-53
6-54
6-54
6-54
* Note: SS = Single DMA channel, Single A/D channel scan
Plug-in DA&C Cards
SM = Single DMA channel, Multiple A/D channel scan
DM = Dual DMA channel, Multiple A/D channel scan
Bus
PCI
Category
Non-Isolated DI/O
Model
PCI-1751/1751U PCI-1753/1753E
TTL DI/O
Input Channels
Output Channels
Isolated DI/O
Output
Channels
PCI-1755
48
96
32
PCI-1730
PCI-1733
PCI-1734
PCI-1752
16
-
-
-
16
-
-
-
Sink Current
24 mA @ 0.4 V
24 mA @ 0.44 V
48 mA @ 0.5 V
8 mA @ 0.5 V
-
-
-
15 mA @ 2.4 V
24 mA @ 3.76 V
15 mA @ 2.4 V
0.4 mA @ 2.4 V
-
-
-
Number of Channels
(Input type)
-
-
-
16 (Sink)
32 (Sink)
-
-
Isolation Voltage
-
-
-
2,500 VDC
2,500 VDC
-
-
Input Range
-
-
-
5 ~ 30 VDC
5 ~ 30 VDC
-
-
Number of Channels
(Output Type)
-
-
-
16 (Sink)
-
32 (Sink)
64 (Sink)
Isolation Voltage
-
-
-
2,500 VDC
-
2,500 VDC
2,500 VDC
Output Range
-
-
-
5 ~ 40 VDC
-
5 ~ 40 VDC
5 ~ 40 VDC
Max. Sink Current
-
-
-
200 mA
-
200 mA
200 mA
Number of Channels
3
-
3
-
-
-
-
Resolution
16-bit
-
16-bit
-
-
-
-
Time Base
5 MHz
-
10 MHz
-
-
-
-
Pattern Match
-


-
-
-
-
Change of State
-


-
-
-
-
Timer/Counter
BoardID™ Switch
-
-


-


Channel-Freeze Function
-
-


-


Output Status Read Back


-

-


Dry/Wet Contact


-
*
*
-
-
175 x 100
175 x 100
175 x 100
175 x 100
175 x 100
175 x 100
175 x 100
1 x DB37
1 x DB37
100-pin SCSI-II
Dimensions (mm)
Connectors
68-pin SCSI-II
100-pin SCSI-II
100-pin SCSI-II
1 x DB37
4 x 20-pin
Windows® 95/98/ME/2000/XP DLL Driver







Windows® 95/98/ME/2000/XP Test Utility







VC++, VB & Delphi Examples







Advantech ActiveDAQ


-




LabView I/O Drivers
(Ver.6i and 7.0)







MathWorks
MATLAB & Simulink
Data Acquisition Tool Box 2.5.1


-




Page
6-31
6-32
6-33
6-34
6-34
6-34
6-36
®
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Isolated DI/O
Source Current
Output
Channel
Input
Channels
Advanced Functions
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Selection Guide
* Dry/wet contact can be mixed at the same time within one group.
IPPC
TPC
FPM
ATM & AWS
DA&C
cPCI
ADAM-3000
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-7
Bus
PCI
Category
Isolated DI/O
TTL DI/O
Model
PCI-1754
PCI-1756
PCI-1758UDI
PCI-1758UDO
PCI-1760U
PCI-1761
PCI-1762
PCI-1750
Input Channels
-
-
-
-
-
-
-
-
Output Channels
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Input
Channels
Isolated DI/O
Sink Current
Output
Channels
Output
Channels
Source Current
Number of Channels
(Input type)
64 (Sink)
32 (Sink)
128
-
8 (Sink)
8 (Sink)
16 (Sink)
16 (Sink)
Isolation Voltage
2,500 VDC
2,500 VDC
2500 VRMS
-
2,500 VDC
2,500 VDC
2,500 VDC
2,500 VDC
Input Range
10 ~ 50 VDC
10 ~ 50 VDC
5 ~ 25 VDC
-
5 ~ 12 VDC
10 ~ 50 VDC
10 ~ 50 VDC
5 ~ 50 VDC
128
8 X Form C
4 X Form A
4 X Form C
16 X Form C
16 (Sink)
2,500 VDC
2,500 VDC
2,500 VDC
2,500 VDC
Number of Channels
(Output Type)
-
Isolation Voltage
Output Range
32 (Sink)
-
-
2,500 VDC
-
2500 VRMS
-
5 ~ 40 VDC
-
5 ~ 40 VDC
Max. Sink Current
-
200 mA
-
90 mA
Number of Channels
-
-
-
Resolution
-
-
Time Base
-
Timer/Counter
Pattern Match
Advanced Functions
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-8
Data Acquisition and
Control Cards
120 VAC @ 0.5 A
30 VDC @ 1 A
250 VAC @ 3 A
24 VDC @ 3 A
120 VAC @ 0.5 A
30 VDC @ 1 A
5 ~ 40 VDC
-
Up CTR for DI
2 X PWM
-
-
1
-
-
16-bit
(2,500 Isolation)
-
-
16-bit
-
-
-
500 Hz for Up
CTR
-
-
1 MHz
-
-
-

-
-
-
200 mA
Change of State
-
-
-
-

-
-
-
BoardID™ Switch







-
Channel-Freeze Function


-
-
-


-
Output Status Read Back
-

-




-
Dry/Wet Contact
-
-



-
-
-
Dimensions (mm)
175 x 100
175 x 100
175 x 100
175 x 100
175 x 100
175 x 100
175 x 100
175 x 100
Connectors
100-pin SCSI-II
100-pin SCSI-II
dual 100-pin
mini-SCSI
dual 100-pin
mini-SCSI
1 X DB37
1 X DB37
1 X DB62
1 X DB37
Windows® 95/98/ME/2000/XP DLL Driver








Windows 95/98/ME/2000/XP Test Utility








VC++, VB & Delphi Examples








Advantech ActiveDAQ








LabView® I/O Drivers
(Ver.6i and 7.0)








MathWorks
MATLAB & Simulink
Data Acquisition Tool Box 2.5.1


-





Page
6-36
6-36
6-38
6-38
6-45
6-44
6-46
6-43
®
* Dry/wet contact can be mixed at the same time within one group.
Plug-in DA&C Cards
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Selection Guide
PCI
ISA
Non-Isolated DI/O
PCL-720+
PCL-722
PCL-724
PCL-731
144
24
48
24 mA @ 0.5 V
24 mA @ 0.5 V
24 mA @ 0.4 V
24 mA @ 0.4 V
3 mA @ 2.4 V
15 mA @ 2.4 V
15 mA @ 2.4 V
15 mA @ 2.4 V
-
-
-
-
-
-
-
32
32
ISA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Counter
Isolated DI/O
PCL-725
PCL-730
PCL-733
PCL-734
PCL-735
PCI-1780
PCL-836
-
16
-
-
-
8
16
-
16
-
-
-
8
16
-
8 mA @ 0.5 V
-
-
-
24 mA @ 0.5 V
8 mA @ 0.5 V
-
0.4 mA @ 2.4 V
-
-
-
15 mA @ 2.4 V
0.4 mA @ 2.4 V
-
8 (Sink)
16 (Sink)
32 (Sink)
-
-
-
-
-
-
1,500 VDC
2,500 VDC
2,500 VDC
-
-
-
-
-
-
5 ~ 24 VDC
5 ~ 24 VDC
5 ~ 24 VDC
-
-
-
-
16 (Sink)
-
32 (Sink)
12 X Form C
-
-
-
-
-
-
4 X Form A
4 X Form C
-
-
-
-
1,000 VDC
1,000 VDC
-
1,000 VDC
1,000 VDC
-
-
-
-
-
-
5 ~ 40 VDC
-
-
-
-
120 VAC @ 0.5 A
30 VDC @ 1 A
5 ~ 40 VDC
200 mA
-
200 mA
0.6 A @ 100 VDC
0.6 A @ 125 VDC
-
3
-
-
-
-
-
-
-
-
8 X CTR
6 X CTR
3 X PWM
16-bit
-
-
-
-
-
-
-
-
16-bit
16-bit
1 MHz
-
-
-
-
-
-
-
-
20 MHz
10 MHz
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-

-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
IPPC
TPC
FPM
ATM & AWS
DA&C
cPCI
ADAM-3000
-
-
-
-
-
-
-
-
-
-
-
185 x 100
334 x 100
125 x 100
185 x 100
147 x 95
185 x 100
185 x 100
185 x 100
155 x 100
175 x 100
185 x 100
5 X 20- pin
6 x 50-pin
1 x 50-pin
2 x 20-pin
2 x 50-pin
1 x DB37
1 x DB37
4 x 20-pin
1 x DB37
1 x DB37
1 x DB37
68-pin
SCSI-II
1 x DB37
2 x 20-pin










































-
-




















-

6-55
6-56
6-56
6-56
6-59
6-57
6-57
6-57
6-59
6-47
6-60
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-9
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-10
PCI-1710
PCI-1710HG
100 kS/s, 12-bit, PCI-bus
Multifunction Card
100 kS/s, 12-bit, (High-gain),
PCI-bus Multifunction Card
Features
 16 single-ended, 8 differential or a combination of analog inputs
 12-bit A/D converter, with up to 100 kHz sampling rate
 Programmable gain for each input channel
 Free combination of single-ended and differential inputs
 On-board 4 K samples FIFO buffer
 Two 12-bit analog output channels
 16 digital inputs and 16 digital outputs
 Programmable pacer/counter
 BoardID™ Switch
 Short circuit protection
PCLD-8710
PCI-1710/1710L/1710HG/1710HGL
Introduction
The PCI-1710 Series are multifunction cards for the PCI bus. Their advanced circuit design provides higher quality and more functions, including the five most desired measurement
and control functions: 12-bit A/D conversion, D/A conversion, digital input, digital output, and counter/timer.
Specifications
 Accuracy
* S.E.: Single-ended
Analog Input
 Channels
 Resolution
 On-board FIFO
 Maximum Input
Overvoltage
 Input Range
16 single-ended or 8 differential
(software programmable)
12-bit
4 K samples
±30 V
(V, software programmable)
Model
PCL-1710/1710L
Bipolar
±10, ±5, ±2.5, ±1.25, ±0.625
Unipolar
0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0
~ 1.25
PCI-1710HG/1710HGL
±10, ±5, ±1, ±0.5, ±0.1 ±0.05, ±0.01,
±0.005
0 ~ 10, 0 ~ 1, 0 ~ 0.1, 0 ~ 0.01
 Common Mode Rejection Ratio (CMRR)
PCI-1710/1710L
Gain
CMRR
0.5, 1
75 dB
2
80 dB
4
84 dB
8
84 dB
 Maximum Sampling Rate
Model
PCI-1710/1710L
PCI-1710HG/1710HGL
Note:
PCI-1710HG/1710HGL
Gain
CMRR
0.5, 1
75 dB
10
90 dB
100
106 dB
1000
106 dB
(S/s, depending on PGIA settling time)
Gain
0.5, 1, 2, 4, 8
0.5, 1
5, 10
20, 100
500, 1000
Max. Sampling Rate
100 kS/s
100 kS/s
35 kS/s
7 kS/s
770 S/s
The sampling rate depends on the computer hardware architecture and software
environment. The rates may vary due to programming language, code efficiency,
CPU utilization and so on.
Gain
PCI-1710/1710L
Accuracy
Gain
PCI-1710HG/1710HGL
Accuracy
Remar.k
0.5, 1
0.01% of FSR ±1 LSB
0.5, 1
0.01% of FSR ±1
LSB
S.E./D
2
0.02% of FSR ±1 LSB
5, 10
0.02% of FSR ±1
LSB
S.E./D
4
0.02% of FSR ±1 LSB
50, 100
0.04% of FSR ±1
LSB
D
8
0.04% of FSR ±1 LSB 500, 1000
0.08% of FSR ±1
LSB
D
 Linearity Error
 Input Impedance
 Trigger Mode
±1 LSB
1 GΩ
Software, onboard programmable pacer or external
Analog Output (PCI-1710/1710HG only)
 Channels
 Resolution
 Relative Accuracy
 Gain Error
 Throughput
 Slow Rate
 Output Range
(software programmable)
 Driving Capability
2
12-bit
±1/2 LSB
±1 LSB
PC dependent, Software update (direct AO)
10 V/ms
Internal reference: 0 ~ +5 V @ -5 V,
0 ~ +10 V @ -10 V
External reference: 0 ~ +x V @ -x V (-10 ≤ x 10)
10 mA
Digital Input
 Channels
 Input Voltage
 Input Load
Plug-in DA&C Cards
(depends on gain)
D: Differential
16
Low: 0.4 V max.
High: 2.4 V min.
Low: -0.2 mA @ 0.4 V
High: 20 mA @ 2.7 V
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1710
PCI-1710HG
Specifications Cont.
Feature Details
Digital Output
PCI-1710 series provide specific functions for different user requirements:
 Channels
 Output Voltage
PCI-1710
16
Low: 0.4 V max. @ 8.0 mA (sink)
High: 2.4 V min. @ -0.4 mA (source)
100 kS/s, 12-bit Multifunction Card
PCI-1710L
100 kS/s, 12-bit Multifunction Card w/o AO
PCI-1710HG
100 kS/s, 12-bit High-Gain Multifunction Card
Programmable Timer/Counter
PCI-1710HGL
100 kS/s, 12-bit High-Gain Multifunction Card w/o AO
 Counter Chip
 Counters
Mixed Single-ended or Differential Analog Inputs
 Input, gate
 Time Base
82C54 or equivalent
3 channels, 16 bits, 2 channels are permanently
configured as a 32-bit programmable pacer; 1 channel
is free for user applications
TTL/CMOS compatible
Channel 1: 10 MHz
Channel 2: Takes input from output of channel 1
Channel 0: Internal 1 MHz or external clock
(10 MHz max.) selected by software.
General
 CE Certified to CISPR 22 class B
 I/O Connector
68-pin SCSI-II female connector
 Power Consumption
+5 V @ 850 mA (Typical),
+5 V @ 1.0 A (Max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
 Dimensions (L x H)
175 x 100 mm (6.9" x 3.9")
 MTBF
Over 64,770 hrs @ 25° C, grounded-fix environment
Ordering Information
 PCI-1710
 PCI-1710L
 PCI-1710HG
 PCI-1710HGL
 PCLD-8710
 PCL-10168
 PCL-10168-2
 ADAM-3968
100 kS/s, 12-bit Multifunction Card, user’s manual and
driver CD-ROM. (cable not included)
100 kS/s, 12-bit Multifunction Card w/o AO, user’s
manual and driver CD-ROM. (cable not included)
100 kS/s, 12-bit High-Gain Multifunction Card, user’s
manual and driver CD-ROM. (cable not included)
100 kS/s, 12-bit High-Gain Multifunction Card w/o
AO, user’s manual and driver CD-ROM. (cable not
included)
Industrial Wiring Terminal Board with CJC circuit for
DIN-rail mounting (cable not included)
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 1 m.
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 2 m.
68-pin SCSI-II Wiring Terminal Board for DIN-rail
Mounting
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
IPPC
TPC
PCI-1710 and PCI-1710HG feature an automatic channel/gain scanning circuit. The circuit,
rather than your software, controls multiplexer switching during sampling. The on-board FPM
SRAM stores different gain values and configurations for each channel. This design lets
you perform multi-channel high-speed sampling (up to 100 KHz) with different gains for
each channel and allows free combination of single-ended and differential inputs.
ATM & AWS
On-board FIFO (First In First Out) Memory
PCI-1710, PCI-1710L, PCI-1710HG and PCI-1710HGL have an on-board FIFO buffer
that can store up to 4 K A/D samples. PCI-1710 and PCI-1710HG generate an interrupt DA&C
when the FIFO is half full. This feature provides continuous high-speed data transfer and
more predictable performance on Windows systems.
cPCI
On-board Programmable Counter
The PCI-1710/1710/1710HG/1710HGL provides a programmable counter to generate a
pacer trigger for the A/D conversion. The counter chip is an 82C54 or equivalent, which
ADAM-3000
includes three 16-bit counters on a 10 MHz clock. One counter is used as an event counter
for counting events coming from the input channels. The other two are cascaded together
to make a 32-bit timer for a pacer trigger.
Motion Control
Special Shielded Cable for Noise Reduction
The PCL-10168 shielded cable is specially designed for the PCI-1710/1710HG to reduce
noise in the analog signal lines. Its wires are all twisted pairs, and the analog lines and ICOM
digital lines are separately shielded, providing minimal cross talk between signals and
great protection against EMI/EMC problems.
eConnectivity
Pin Assignments
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-11
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-12
PCI-1711
PCI-1711L
100 kS/s, 12-bit, 16-ch S.E. Inputs Low-cost
Multifunction Card
100 kS/s, 12-bit, 16-ch S.E. Inputs Low-cost
Multifunction Card w/o AO
Features
 16 single-ended analog inputs
 12-bit A/D converter, with up to 100 kHz sampling rate
 Programmable gain for each input channel
 Automatic channel/gain scanning
 On-board 1K samples FIFO buffer
 Two 12-bit analog output channels (Only for PCI-1711)
 16 digital inputs and 16 digital outputs
 Programmable pacer/counter
PCI-1711/1711L
PCLD-8710
Introduction
PCI-1711 and PCI-1711L are powerful, but low-cost multifunction cards for the PCI bus. PCI-1711 comes with 2 analog output channels, while the PCI-1711L doesn’t. Thus,
PCI-1711L represents a cost saver for those that do not need analog output.
Specifications
Analog Output (only for PCI-1711)
Analog Input




Channels
Resolution
FIFO Size
Sampling Rate*
Input range and
Gain List
Drift (ppm/°C)
Small Signal
Bandwidth for
PGA




16 Single-Ended
12-bit
1K samples
100 kS/s max.
Gain
Input
Gain
Zero
Gain
Gain
4
8
16
± 2.5 V ± 1.25 V ± 0.625 V
4
8
16
15
15
15
25
30
40
4
8
16
0.65
0.35
Bandwidth 4.0 MHz 2.0 MHz 1.5 MHz
MHz
MHz
Max. Input Overvoltage
Input Protect
Input Impedance
Trigger Mode
DC
Accuracy
AC
1
± 10 V
1
15
25
1
2
±5V
2
15
25
2
20 V
30 Vp-p
2 MΩ/5 pF
Software, On-board Programmable Pacer or external
INLE: ±0.5 LSB
Monotonicity: 12 bits
Offset error: Adjustable to zero
Gain error: 0.005% FSR (Gain=1)
SNR: 68 dB
ENOB: 11 bits
Programmable Counter / Timer





Channels
Resolution
Compatibility
Base Clock
Max. Input Frequency
1
16-bit
TTL level
10 MHz
10 MHz
Note:
The sampling rate and throughput depends on the computer hardware architecture and
software environment. The rates may vary due to programming language, code efficiency,
CPU utilization and so on.
Plug-in DA&C Cards
 Channels
 Resolution
2
12-bit
Output Range
(Internal & External
Reference)
Accuracy








Internal Reference
0 ~ +5 V, 0 ~ +10 V
External Reference
0 ~ +x V @ -x V (-10 ≤ x ≤ 10)
Relative
±1/2 LSB
Differential Non-linearity
±1/2 LSB
Gain Error
Slew Rate
Drift
Driving Capability
Throughput
Output Impedance
Settling Time
Reference Voltage
Adjustable to zero
11 V/µs
40 ppm/° C
3 mA
PC dependent, Software update (direct AO)
0.81 Ω
26 µs (to ±1/2 LSB of FSR)
Internal
-5 or -10 V
External
-10 or +10 V
Digital Input / Output
16
Input Channels
Input Voltage
Low
High
0.8 V max.
2.0 V max.
Low
High
16
0.8 V max.@ 8.0 mA (sink)
2.0 V min.@ -0.4 mA (source)
Output Channels
Output Voltage
General
I/O Connector Type
Dimensions
Power Consumption
Temperature
Relative Humidity
68-pin SCSI-II female
175 x 100 mm (6.9” x 3.9”)
PCI-1711
PCI-1711L
Typical
+5 V @ 850 mA
+5 V @ 700 mA
Max.
+5 V @ 1.0 A
0 ~ 60° C (32 ~ 140° F)
Operation
(refer to IEC 68-2-1, 2)
Storage
-20 ~ 70° C (-4 ~ 158° F)
5 % ~ 95 % RH non-condensing (refer to IEC 68-2-3)
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1711/1711L
Ordering Information
 PCI-1711
 PCI-1711L
 PCLD-8710
 PCL-10168
 ADAM-3968
Feature Details
100 kS/s, 12-bit, 16-ch S.E. inputs Low-cost
Multifunction Card, user's manual and driver CD-ROM.
(cable not included)
100 kS/s, 12-bit, 16-ch S.E. inputs Low-cost
Multifunction Card w/o analog output, user's manual
and driver CD-ROM. (cable not included)
Industrial Wiring Terminal Board with CJC circuit for
DIN-rail mounting (cable not included)
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction,
1 and 2 m
68-pin SCSI-II Wiring Terminal Board for DIN-rail
Mounting
Pin Assignments
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Plug & Play Function
PCI-1711 and PCI-1711L fully comply complies with the PCI Specification Rev 2.1. and
thus are Plug & Play devices. During card installation, it is virtually unnecessary to set any IPPC
jumpers or DIP switches. Instead, all bus-related configurations such as base I/O address
and interrupts are conveniently taken care of by the Plug & Play function.
TPC
Flexible Input Types and Range Settings
PCI-1711 and PCI-1711L feature an automatic channel/gain scanning circuit. This
circuit design controls multiplexer switching during sampling. You can set different
FPM
gain values for each channel according to your needs for the corresponding range of
input voltages. The gain values thus selected are stored in the SRAM. This flexible design
enables multi-channel and high-speed sampling for high-performance data acquisition
ATM & AWS
(up to 100 kS/s).
On-board FIFO Memory
PCI-1711 and PCI-1711L provide an onboard FIFO (First In First Out) memory buffer, DA&C
storing up to 1 K A/D samplings. You can either enable or disable the interrupt request
feature of the FIFO buffer. While the interrupt request for FIFO is enabled, you can further
specify whether the interrupt request will be sent whenever one sampling takes place or
cPCI
when the FIFO buffer is half saturated. This feature enables a continuous high-speed data
transfer with more predictable performance on Windows systems.
Onboard Programmable Counter
ADAM-3000
PCI-1711 and PCI-1711L are equipped with a programmable counter, which can serve as
a pacer trigger for A/D conversions. The counter chip is an 82C54 or equivalent, which
incorporates three 16-bit counters on a 10 MHz clock. One of the three counters is used Motion Control
as an event counter for input channels. The other two are cascaded into a 32-bit timer
for pacer triggering.
ICOM
Applications
 Process monitoring and control
 Transducer and sensor measurement
eConnectivity
 Multi-channel DC voltage measurement
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-13
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-14
PCI-1712
PCI-1712L
1MS/s, 12-bit High-speed
Multifunction Card
1MS/s, 12-bit High-speed
Multifunction Card w/o AO function
Features
 PCI-bus mastering for data transfer
 16 single-ended, 8 differential or a combination of analog inputs
 12-bit A/D converter, with up to 1 MHz sampling rate
 Pre-, post-, about- and delay-trigger data acquisition modes for analog input
channels
 Programmable gain for each analog input channel
 Automatic channel/SD*/BU* scanning
 On-board FIFO buffer storing up to 1K samples for A/D and 32K samples for
D/A
 Two 12-bit analog output channels with continuous waveform output function
 Auto calibration of analog input and output channels
 16 digital input and output channels
PCI-17112/1712L
 Three 16-bit programmable multifunction counter/timers on 10 MHz
PCLD-8712
Introduction
The PCI-1712/1712L is a powerful high-speed multifunction card for the PCI bus. It features a 1 MHz 12-bit A/D converter, an onboard FIFO buffer (storing up to 1 K samples for A/D,
and up to 32 K samples for D/A conversion). The PCI-1712 provides a total of up to 16 single-ended or 8 differential A/D input channels or a mixed combination, two 12-bit D/A output
channels, 16 digital input/output channels, and three 10MHz 16-bit multifunction counter channels. PCI-1712/1712L provides specific functions for different user requirements:
Specifications
Analog Output
Analog Input
Channels
Resolution
Max. Sampling
Rate
16 Single-Ended or 8 Differential or Combination
FIFO Size
12-bit
1 K samples
Multi-channel, single gain: 1 MS/s
Multi-channel, multi gain: 600 kS/s
Multi-channel, multi gain, unipolar/bipolar: 400 kS/s
Common Mode
voltage
Input Range and
Gain List
±11 V max. (operational)
Gain
0.5
1
2
8
Digital Input /Output
Input
Voltage
Note:
16
Low
0.8 V max.
0.5 V max. @ +24 mA
Low
(sink)
Number of
ports
High
High
2 (8-ch/port)
2.0V min.
2.4 V min. @ -15 mA
(source)
The sampling rate depends on the computer hardware architecture and software
environment. The rates may vary due to programming language, code efficiency,
CPU utilization and more.
Plug-in DA&C Cards
Output Range
(Internal & External
Reference)
Accuracy
4
Unipolar
N/A
0 ~ 10
0~5
0 ~ 2.5 0 ~ 1.25
Bipolar
±10
±5
±2.5
±1.25
±0.625
Gain
0.5
1
2
4
8
Drift
Zero (µV/° C)
±80
±30
±30
±30
±30
Gain (ppm/° C)
±30
±30
±30
±30
±30
Gain
0.5
1
2
4
8
Small Signal
Bandwidth for PGA
Bandwidth
4.0 MHz 4.0 MHz 2.0 MHz 1.5 MHz 0.65 MHz
Max. Input Voltage
Input Protect
±20 V
30 Vp-p
Input Impedance
100Ω 10pF (Off); 100Ω 100pF (On)
Software, On-board Programmable Pacer or External,
Trigger Mode
Pre-trigger, Post-trigger, Delay-trigger, About-trigger
DNLE: ±1LSB; INLE: ±1LSB; Offset error < 1LSB
Gain
0.5
1
2
4
8
DC
Accuracy
Gain Error:
0.15
0.03
0.03
0.05
0.1
(% FSR)
AC
SNR: 68 dB; ENOB: 11 bits; THD: -75 dB typical
Input
Channels
Channels
Resolution
Operation Mode
Offset
Drift
Max. Transfer Rate
Output Impedance
Settling Time
2
FIFO Size
12-bit
32 K samples
Single output, continuous output, waveform output
Using Internal
0 ~ +5 V, 0 ~ +10 V, -5 ~ +5 V, -10 ~ +10 V
Reference
0 ~ +x V @ +x V (-10 ≤ x ≤ 10)
Using External
Reference
-x ~ +x V @ +x V (-10 ≤ x ≤ 10)
Relative
±1 LSB
Differential
±1 LSB (monotonic)
Non-linearity
<1 LSB
20 V/µs
Slew Rate
Driving Capability
10 ppm/° C
±10 mA
Single Channel: 1 MS/s max. for FSR
Dual Channel: 500 kS/s max. for FSR
0.1 Ω max.
5 MHz
Max. Digital Update Rate
2 µs (to ±1/2 LSB of FSB)
Counter/Timer
Channels
Compatibility TTL level
BASE Clock
Clock Input
Gate Input
Counter
Low
Low
Low
Resolution
3
Max. Input Frequency
10 MHz, 1 MHz, 100 KHz, 10 KHz
0.8 V max.
0.8 V max.
0.5 V max. @ +24 mA
High
High
High
16-bit
10 MHz
2.0 V min.
2.0 V min.
2.0 V min. @ -15 mA
General
I/O Connector Type
68-pin SCSI-II female
Dimensions
175 x 100 mm (6.9” x 3.9”)
Power Consumption
Temperature
Typical
+5 V @ 850 mA; +12 V @ 600 mA
Max.
+5 V @ 1 A; +12 V @ 700 mA
Operating
0 ~ 60° C (32 ~ 140° F)
(refer to IEC 68-2-1, 2)
Storage
-20 ~ 85° C (-4 ~ 185° F)
Relative Humidity
5 ~ 95 % RH non-condensing (refer to IEC 68-2-3)
Certification
CE certified
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1712
PCI-1712L
Ordering Information
 PCI-1712
 PCI-1712L
 PCLD-8712
 PCL-10168
 ADAM-3968
Feature Details
1MS/s, 12-bit High-speed Multifunction Card, user’s
manual and driver CD-ROM. (cable not included)
1MS/s, 12-bit High-speed Multifunction Card w/o
AO, user’s manual and driver CD-ROM. (cable not
included)
Industrial Wiring Terminal Board for DIN-rail mounting.
(cable not included)
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 1 and 2
m
68-pin SCSI-II Wiring Terminal Board for DIN-rail
Mounting
PCI-bus Mastering Data Transfer
PCI-1712 and PCI-1712L support PCI-Bus mastering DMA for high-speed data transfer
and gap-free analog input and analog output. By setting aside a block of memory in the PC, IPPC
PCI-1712 and PCI-1712L perform bus-mastering data transfers without CPU intervention,
setting the CPU free to perform other more urgent tasks such as data analysis and graphic
manipulation. The function allows users to run all I/O functions simultaneously at full
TPC
speed without losing data.
Plug & Play Function
PCI-1712 and PCI-1712L are Plug & Play devices, which fully complies with the PCI FPM
Specification Rev 2.2. During card installation, there is no need to set any jumpers or DIP
switches. Instead, all bus-related configurations such as base I/O address and interrupt
are automatically done by the Plug & Play function.
ATM & AWS
On-board FIFO Memory
Pin Assignments
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
PCI-1712 provides an on-board FIFO (First In First Out) memory buffer, storing up to 1K
samples for A/D and 32K for D/A conversion.
DA&C
Automatic Channel/Gain/SD*/BU* Scanning
PCI-1712 and PCI-1712L feature an automatic channel/Gain/SD/BU scanning circuit.
This circuit controls multiplexer switching during sampling in a way that is much more cPCI
efficient than software implementation. Onboard SRAM stores different gain, SD and BU
values for each channel. This combination lets users perform multi-channel high-speed
sampling with different gain, SD and BU values for each channel.
ADAM-3000
SD: Single-Ended/Differential; BU: Bipolar/Unipolar
Flexible Triggering and Clocking Capabilities
Motion Control
PCI-1712 and PCI-1712L provide flexibility in triggering action, both in the available
trigger modes and trigger events for analog input. You can acquire data using post-trigger,
pre-trigger, delay-trigger and about-trigger modes. The trigger source could be either an
ICOM
analog or digital signal. The analog trigger could originate from a dedicated input pin.
In fact, you can designate any of the analog input channels as the analog trigger input.
You can set the analog trigger level within a voltage range from zero to A/D FSR. With
the trigger signal being digital, you can pace A/D and D/A conversion using software eConnectivity
interrupt, internal or external clock.
Continuous Analog Output (PCI-1712 only)
UNO
PCI-1712 provides two analog output channels. Both can perform continuous waveform
output. The analog output can be up to 500 kS/s for each analog output channel. Or you
can load a cyclic waveform into an on-board FIFO, which will continuously output the
cyclic waveform. The on-board FIFO of the PCI-1712 can store 2 to 32K samples of the ADAM-4000
waveform.
Block Diagram
On-board Programmable Multifunction Counter/Timer
ADAM-5000
PCI-1712 and PCI-1712L are equipped with 3 programmable multifunction counter/timers,
which can serve as a pacer trigger for A/D conversion. The counter chip is an 82C54
or equivalent, which incorporates three 16-bit channels on a 10 MHz clock. And then
we enhance the gate and clock input function for more applications, of event counting, ADAM-6000
pulse generation, duty cycle frequency generation, one shot, frequency measurement
and pulse width measurement.
ADAM-8000
BAS
32K
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-15
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-16
PCI-1716
PCI-1716L
16-bit High-resolution
Multifunction Card
16-bit High-resolution
Multifunction Card w/o AO function
Features
 16-bit high resolution
 250 kS/s sampling rate
 Auto calibration function
 PCI-bus mastering for data transfer
 16 analog input channels with 1K FIFO
 16 S.E. or 8 Diff. AI, or a combination
 Unipolar/Bipolar input range
 2 analog output channels (PCI-1716 only)
 16 digital input channels
 16 digital output channels
 One 10 MHz 16-bit resolution counter
 BoardID™ Switch
Introduction
PCI-1716 and PCI-1716L are powerful high-resolution multifunction cards for the PCI bus. They feature a 250 kS/s 16-bit A/D converter, and an on-board 1K sample FIFO buffer for
A/D. The cards can also have up to sixteen single-ended or eight differential A/D input channels or a combination of these; two 16-bit D/A output channels, 16 digital input/output
channels, and one 10 MHz 16-bit counter channel. PCI-1716 and PCI-1716L provide specific functions for different user requirements.
Specifications
Analog Input




Channels
Resolution
FIFO Size
Sampling Rate*
Input range and
Gain List
Small Signal
Bandwidth for PGA
Gain





Clocking and
Trigger Inputs
Input Channels
Input Voltage
16 Single-Ended, 8 differential or combination
16-bit
1K samples
250 kS/s max.
Gain
Unipolar
Bipolar
Gain
Bandwidth
Common Mode Voltage
Max. Input Overvoltage
Input Protection
Input Impedance
Trigger Mode
Accuracy
Digital Input /Output
0.5
N/A
± 10
0.5
1
0 ~10
±5
1
2
0 ~5
± 2.5
2
4
0 ~2.5
± 1.25
4
Input Load
0.4 V max.
2.4 V max.
0.4 V max.@ -0.2 mA
2.7 V max.@ 2.0 µA
Low
High
16
0.4 V max.@ 0.8 mA (sink)
2.4 V min.@ -0.4 mA (source)
Output Channels
8
0 ~1.25
± 0.625
8
Output Voltage
Counter/Timer
 Channels
4.0 MHz 4.0 MHz 2.0 MHz 1.5 MHz 0.65 MHz
± 11 V max. (operational)
±20 V
30 Vp-p
100 MΩ/10 pF (Off); 100 MΩ/100pF (On)
Software, Onboard Programmable Pacer or external
DNLE: ±1 LSB
INLE: ±1 LSB
Zero (Offset) error: Adjustable ±1 LSB
DC
Gain
0.5
1
2
4
8
Gain error
0.15
0.03
0.03
0.05
0.1
(%FSR)
SNR: 82 dB
AC ENOB: 13.5 bits
THD: -84 dB typical
Trigger Mode
Software, on-board programmable pacer or external
A/D pacer clock 250 k Hz (max.); 58 µHz (min.)
External A/D
Min. Pulse width: 2 µs (high); 2 µs (low)
trigger clock
Max. frequency: 250 KHz
Note:
The sampling rate and throughput depends on the computer hardware architecture and
software environment. The rates may vary due to programming language, code efficiency,
CPU utilization and other factors.
Plug-in DA&C Cards
16
Low
High
Low
High
 Resolution
 Compatibility
 Base Clock
 Max. Input Frequency
Clock Input
Gate Input
Counter Output
General
 I/O Connector Type
 Dimensions
 Power Consumption
3 channels, 2 channels are permanently configured
as programmable pacers; 1 channel is free for user
application
16-bit
TTL level
Channel 2: Takes input from output of channel 1
Channel 1: 10 MHz
Channel 0: Internal 1 MHz or external clock (10 MHz)
max Selected by software
1 MHz
Low
High
Low
High
Low
High
0.8 V max.
2.0 V min.
0.8 V max.
2.0 V min.
0.5 V max. @ +24 mA
2.4 V min. @ -15 mA
68-pin SCSI-II female
175 x 100 mm (6.9” x 3.9”)
Typical +5 V @ 850 mA, +12 V @ 600 mA
Max.
+5 V @ 1 A, +12 V @ 700 mA
 Operating Temperature 0 ~ 60° C (32 ~ 158° F) (refer to IEC 68-2-1, 2)
 Storage Temperature -20 ~ 85° C (-4 ~ 158° F)
 Operating Humidity
5 ~ 85% RH non-condensing(refer to IEC 68-1, -2, -3)
 Storage Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-1, -2, -3)
 Certifications
CE
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1716
PCI-1716L
Analog Output (PCI-1716 only)




Channels
Resolution
Operation Mode
Throughput*
Plug & Play Function
2
16-bit
Single output
PC dependent, Software update (direct AO)
Using Internal
0 ~ +5 V, 0 ~ +10 V, -5 ~ +5 V, -10 ~ +10 V
Reference
0 ~ +x V @ +x V (-10 ≤ x ≤ 10)
Using External
Reference
-x ~ +x V @ +x V (-10 ≤ x ≤ 10)
DNLE: ±1 LSB (monotonic)
INLE: ±1 LSB
Accuracy
DC
Zero (Offset) error: Adjustable ±1 LSB
Gain (Full-scale) error: Adjustable ±1 LSB
Settling
5 µs (to 4 LSB of FSB)
Time
Dynamic
Performance
Slew
20 V/µs
Rate
Drift
10 ppm/° C
Driving Capability
±20 mA
Output Impedance
0.1 Ω max.
Output Range
(Internal
& External
Reference)
 Drift
 Driving Capability
 Output Impedance
10 ppm/° C
Ordering Information
 PCI-1716
 PCI-1716L
 PCLD-8710
 PCL-10168
 ADAM-3968
Automatic Channel/Gain/SD*/BU* Scanning
TPC
PCI-1716 and PCI-1716L feature an automatic channel/gain/SD/BU scanning circuit. This
circuit controls multiplexer switching during sampling in a way that is more efficient than
software implementation. On-board SRAM stores different gain, SD and BU values for
each channel. This combination lets users perform multi-channel high-speed sampling FPM
with different gain, SD and BU values for each channel.
SD: Single-Ended/Differential; BU: Bipolar/Unipolar
ATM & AWS
On-board FIFO Memory
PCI-1716 and PCI-1716L provide 1K sample on-board FIFO (First In First Out) memory
buffer for AD. This is an important feature for faster data transfer and more predictable
DA&C
performance under the Windows system.
On-board Programmable Timer/Counter
±20 mA
0.1 Ω max.
250 kS/s, 16-bit, 16-ch High-resolution Multifunction
Card, user’s manual and driver CD-ROM. (cable not
included)
250 kS/s, 16-bit, 16-ch High-resolution Multifunction
Card w/o analog output, user’s manual and driver
CD-ROM. (cable not included)
Industrial Wiring Terminal Board with CJC circuit for
DIN-rail Mounting. (cable not included)
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction,
1 and 2 m
68-pin SCSI-II Wiring Terminal Board for DIN-rail
Mounting
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PCI-1716 and PCI-1716L are Plug & Play devices, which fully complies with PCI Software
Specification Rev 2.2. During card installation, there is no need to set jumpers or DIP
switches (Unless you are using several identical cards (See BoardID switch)). Instead,
all bus-related configurations such as base I/O address and interrupt are automatically IPPC
done by the Plug & Play function.
PCI-1716 and PCI-1716L provide a programmable timer counter for generating a pacer cPCI
trigger for the A/D conversion. The timer/counter chip is 82C54, which includes three
16-bit counter 10 MHz clocks. One counter is used as an event counter for counting
events coming from the input channel. The other two are cascaded together to make a ADAM-3000
32-bit timer for a pacer trigger time base.
Pin Assignments
Motion Control
ICOM
eConnectivity
UNO
Feature Details
ADAM-4000
PCI-Bus Mastering Data Transfer
PCI-1716 and PCI-1716L support PCI-Bus mastering DMA for high-speed data transfer
and gap-free analog input and analog output. By setting aside a block of memory in
the PC, PCI-1716 and PCI-1716L performs bus-mastering data transfers without CPU
intervention, setting the CPU free to perform other more urgent tasks such as data analysis
and graphic manipulation. The function allows users to run all I/O functions simultaneously
at full speed without losing data.
ADAM-5000
ADAM-6000
Auto-calibration Function
PCI-1716 and PCI-1716L provide an auto-calibration function by using a calibration
utility. The built-in calibration circuitry of the PCI-1716 and PCI-1716L corrects gain and
offset errors in analog input and analog output channels thereby eliminating the need for
external equipment and user adjustments.
ADAM-8000
BAS
BoardID™ Switch
PCI-1716 and PCI-1716L have a built-in BoardID™ DIP switch that helps define each
card’s unique identity when multiple identical PCI cards have been installed in the same
computer. The BoardID switch is very useful when you build your system with multiple
identical PCI cards. With the correct BoardID switch settings, you can easily identify and
access each card during hardware configuration and software programming.
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-17
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-18
PCI-1718HDU
PCI-1718HGU
12-bit Multi-function Card with PCI BUS
12-bit High-gain Multi-function card
with PCI BUS (ISA Compatible)
Features
NEW
 16 single-ended or 8 differential analog inputs
 12-bit A/D converter
 Programmable gain for each input channel
 Automatic channel/gain/SD scanning
 On-board FIFO for AI
 One 12-bit analog output channel
 16 digital inputs and 16 digital outputs
 PCI-bus mastering for data transfer
 Universal PCI bus (support 3.3 V or 5 V PCI bus signal)
 BoardID™ switch
Introduction
PCI-1718HDU/HGU is a multifunction data acquisition card based on the PCI bus. It offers the five most desired measurement and control functions: 12-bit A/D conversion, 12-bit
D/A conversion, digital input, digital output, and counter/timer.
PCI-Bus Plug & Play
The PCI-1718HDU/HGU uses a PCI controller to interface the card to the PCI bus. The controller fully implements the PCI bus specification Rev 2.2. All bus relative configurations,
such as base address and interrupt assignment, are automatically controlled by software. No jumper or DIP switch is required for user configuration.
Automatic Channel/Gain/ SD Scanning
PCI-1718HDU/HGU features an automatic channel/Gain/SD scanning circuit. This circuit, instead of your software, controls multiplexer switching during sampling. On-board SRAM
stores different gain and SD values for each channel. This combination lets user perform multi-channel high-speed sampling (up to 100kHz) with different gains and SD for each
channel.
On-board FIFO
There are 4k samples FIFO for A/D (AI) on PCI-1718HDU/1718HGU. This is an important feature for faster data transfer and more predictable performance under Windows system.
On Board Programmable Timer/Counter
PCI-1718HDU/1718HGU provides a programmable timer counter for generating pacer trigger for the A/D conversion. The timer/counter chip is 82C54, which includes three 16-bit
counters of 10 MHz clock. One counter is used as an event counter for counting events coming from the input channel. The other two are cascaded together to make a 32-bit timer
for pacer trigger time base.
Specifications
PCI-1718HDU/
HGU PGA
Bandwidth
Analog Input




Channels
Resolution
FIFO Size
Max. Sampling Rate
Input range and
Gain List for
PCI-1718HDU/
HGU
Input range and
Gain List for
PCI-1718HDU/
HGU
PCI-1718HDU/
HGU PGA
Bandwidth
Drift
16 single-ended or 8 differential or combination
12-bit
4 K samples
100 kS/s
Gain
Unipolar
0.5
N/A
1
0~10
2
0~5
4
0~2.5
8
0~1.25
Bipolar
±10
±5
±2.5
±1.25
±0.625
Gain
Unipolar
0.5
N/A
1
0~10
5
N/A
10
0~1
50
N/A
100
0~0.1
Bipolar
±10
±5
±1
±0.5
±0.1
±0.05 ±0.01 ±0.005
500
N/A
1000
0~0.01
Gain
0.5, 1
2
4
8
Bandwidth
5.0 MHz
4.0 MHz
1.3 MHz
0.6 MHz





Gain
0.5, 1
5, 10
Bandwidth
1.0 MHz
80 kHz
Zero (µV/.)
Gain (ppm/.)
Common Mode Voltage
Max. Input voltage
Input Protection
Input Impedance
Trigger Mode
PCI-1718HDU/HGU
Accuracy
DC
AC
50, 100
500, 1000
10 kHz
1 kHz
15
40
±11 V max. (operational)
±15 V
30 Vp-p
100 MΩ/10pF(Off); 100 MΩ/100pF(On)
Software, on-board or external programmable pacer
DNLE: ±1LSB
INLE: ±1LSB
Offset error: Adjustable to 0
Gain
0.5
1
2
Gain error(% FSR)
0.01 0.01 0.02
THD: -80 dB
ENOB: 11 bits
4
0.02
8
0.04
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1718HDU
PCI-1718HGU
DNLE: ±1LSB
INLE: ±1LSB
Offset error: Adjustable to 0
Gain
0.5,1 5,10 50,100
Gain error(% FSR)
0.01 0.02 0.02
THD: -80 dB
ENOB: 11 bits
0.8 V max.
2.0 V min.
DC
PCI-1718HDU/HGU
Accuracy
AC
External TTL Trigger
Input
Low
High
500 1000
0.04 0.08
Output Range
(Internal & External
Reference)








1
12-bit
100 kS/s
Using Internal Reference
0 ~ +5 V, 0 ~ +10 V
0~xV@xV
(-10 ≤ x ≤ 10)
±1 LSB
±1 LSB (monotonic)
Adjustable to ±1 LSB
Adjustable to ±1 LSB
10 V/µs
2µs to 0.01% of FSR
Using External Reference
Accuracy
Dynamic Performance
 Drift
 Driving Capability
 Output Impedance
INLE
DNLE
Offset error
Gain error
Slew Rate
Settling Time
Digital Input
16
Low
High
Low
High
Input Voltage
Input Load
0.4 V max.
2.4 V min.
0.4 V max.@ -0.2 mA
2.7 V min.@ 20 µA
Digital Output
Output Channels
16
0.4 V max.@ +8.0 mA (sink)
2.4 V min.@-0.4 mA(source)
Low
High
Output Voltage
Counter/Timer
 Counter Chip
 Channels
 Resolution
 Compatibility
 Base Clock
 Max. Input Frequency
82C54 or equivalent
3 channels, 2 channels are permanently configured
as programmable pacers; 1 channel is free for user
application
16 bit
TTL level
Channel 1: 10 MHz
Channel 2: Takes input from output of channel 1
Channel 0: Internal 100 kHz or external clock (10 MHz
max.) selected by software
10 MHz
Low
High
Low
High
Low
High
Clock Input
Gate Input
Counter Output
0.8 V max.
2.0 V min.
0.8 V max.
2.0 V min.
0.5 V max.@ +24 mA
2.4 V min.@ -15 mA
General
 I/O Connector Type
 Dimensions
Power
Consumption
Typical
Max.
37-pin DSUB female for Analog One 20-pin Box
Header for DI One 20-pin Box Header for DO
175 x 100 mm (6.9” x 3.9”)
+5 V @ 850 mA
+5 V @ 1 A
PCI-1718HDU
PCI-1718HGU
PCL-10120-1
PCL-10120-2
PCL-10137-1
PCL-10137-2
PCL-10137-3
PCLD-8115
12-bit multi-function card with PCI bus
12-bit high-gain multi-function card with PCI bus
20-pin flat cable, 1m
20-pin flat cable, 2m
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Wiring terminal board CE
Pin Assignments
10 ppm/°C
±10mA
0.1 Ω max.
Input Channels
Relative
Humidity
Certification
0 ~ 60 °C (32 ~ 158 °F)
-20 ~ 70 °C (-4 ~ 158 °F)
5~85%RH non-condensing (refer to IEC 68-1,-2,-3)
5~95%RH non-condensing (refer to IEC 68-1,-2,-3)
CE certified
Ordering Information
Analog Output
 Channels
 Resolution
 Max. Transfer Rate
Operating
Storage
Operating
Storage
Temperature
A/D S0
A/D S1
A/D S2
A/D S3
A/D S4
A/D S5
A/D S6
A/D S7
A.GND
A.GND
V.REF
S0*
+12 V
S2*
D.GND
NC
Counter 0 CLK
Counter 0 OUT
+5V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
IPPC
TPC
FPM
ATM & AWS
DA&C
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
A/D S8
A/D S9
A/D S10
A/D S11
A/D S12
A/D S13
A/D S14
A/D S15
A.GND
A.GND
DA0.OUT
DA0.VREF
S1*
S3*
D.GND
EXT.TRIG
Counter 0 GATE
PACER
cPCI
ADAM-3000
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
A/D S0
A/D S1
A/D S2
A/D S3
A/D S4
A/D S5
A/D S6
A/D S7
A.GND
A.GND
V.REF
S0*
+12 V
S2*
D.GND
NC
Counter 0 CLK
Counter 0 OUT
+5V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
A/D S8
A/D S9
A/D S10
A/D S11
A/D S12
A/D S13
A/D S14
A/D S15
A.GND
A.GND
DA0.OUT
DA0.VREF
S1*
S3*
D.GND
EXT.TRIG
Counter 0 GATE
PACER
A/D H0
A/D H1
A/D H2
A/D H3
A/D H4
A/D H5
A/D H6
A/D H7
A.GND
A.GND
V.REF
S0*
+12 V
S2*
D.GND
NC
Counter 0 CLK
Counter 0 OUT
+5V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
A/D L0
20
A/D L1
21
A/D L2
22
A/D L3
23
A/D L4
24
A/D L5
25
A/D L6
26
A/D L7
27
A.GND
28
A.GND
29
30 DA0.OUT
31 DA0.VREF
S1*
32
S3*
33
D.GND
34
35 EXT.TRIG
36 Counter 0 GATE
PACER
37
Online Download www.advantech.com/products
All product specifications are subject to change without notice
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Last updated : January 2005
ADAM-6000
ADAM-8000
BAS
6-19
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-20
PCI-1741U
16-bit, 200 kS/s Low cost
Multifunction card w/AO
Features
NEW
 16-bit high resolution
 200 kS/s sampling rate
 Auto calibration function
 16 S.E. or 8 Diff. AI
 Unipolar/Bipolar input range
 1 K samples FIFO for AI
 Universal PCI bus (support 3.3 V or 5 V PCI bus signal)
 BoardID™ switch
Introduction
PCI-1741U is a powerful high-resolution multifunction DAS card for the PCI bus. Its sampling rate is up to 200 kS/s and the 16-bit resolution makes it suitable for most data
acquisition applications. PCI-1741U provides 16 single-ended or 8 differential analog input channels, one 16-bit D/A output channel, 16 digital input/output channels, and one 10
MHz 16-bit counter channel.
Auto-calibration Function
PCI-1741U provides an auto-calibration function by using a calibration utility. The built-in calibration circuitry of the PCI-1741U corrects gain and offset errors in analog input and
analog output channels thereby eliminating the need for external equipment and user adjustments.
BoardID™ Switch
PCI-1741U has a built-in BoardID™ DIP switch that helps define each card’s unique identity when multiple identical PCI cards have been installed in the same computer. The BoardID
switch is very useful when you build your system with multiple identical PCI cards. With the correct BoardID switch settings, you can easily identify and access each card during
hardware configuration and software programming.
Plug & Play Function
The PCI-1741U is a Plug & Play device, which fully complies with PCI Specification Rev 2.2. During card installation, there is no need to set jumpers or DIP switches. Instead, all
bus-related configurations such as base I/O address and interrupt are automatically done by the Plug & Play function.
On-board FIFO Memory
The PCI-1741U provides 1K samples on-board FIFO (First In First Out) memory buffer for AD. This is an important feature for faster data transfer and more predictable performance
under the Windows system.
On Board Programmable Timer/Counter
The PCI-1741U provides a programmable timer counter for generating a pacer trigger for the A/D conversion. The timer/counter chip is 82C54, which includes three 16-bit counter
10 MHz clocks. One counter is used as an event counter for counting events coming from the input channel. The other two are cascaded together to make a 32-bit timer for pacer
trigger time base.
Specifications
Analog Input




Channels
Resolution
FIFO Size
Max. Sampling Rate
Input range and
Gain List
Bandwidth for PGA




16 single-ended or 8 differential or combination
16-bit
1 K samples
200 kS/s
Gain
Unipolar
Bipolar
Gain
Bandwidth
Common mode voltage
Max. Input voltage
Input Protect
Input Impedance
0.5
N/A
±10
0.5
4.0
MHz
1
0~10
±5
1
4.0
MHz
2
0~5
±2.5
2
2.0
MHz
4
0~2.5
±1.25
4
1.5
MHz
±11 V max. (operational)
±20 V (protection)
30Vp-p
100 MΩ/10pF(Off); 100 MΩ/100pF(On)
8
0~1.25
±0.625
8
0.65
MHz
DC
Accuracy
AC
Clocking
and Trigger
Inputs
Trigger Mode
A/D pacer clock
DNLE: ±1LSB
INLE: ±1LSB
Zero (Offset) error: Adjustable to ±1 LSB
Gain
0.5
1
2
4
8
Gain error
0.03 0.02 0.02 0.03 0.04
(% FSR)
THD: -90 dB
ENOB: 13.5 bits
Software, on-board programmable pacer or
external
200 kHz (max.); 2.328mHz (min.)
Analog Output




Channels
Resolution
Operation mode
Throughput
1
16-bit
Single output
PC dependent, Software update (Direct AO)
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1741U
Using Internal
Output Range
Reference
(Internal & External
Using External
Reference)
Reference
Accuracy
DC
Settling Time
Slew Rate
Dynamic
Performance
 Drift
 Driving Capability
 Output Impedance
0 ~ +5 V, 0 ~ +10 V,
-5 ~ +5 V,-10 ~ +10 V
0 ~ +x V@ +x V (-10.x.10)
-x ~ +x V@ +x V (-10.x.10)
DNLE: ±1LSB (monotonic)
INLE: ±1LSB
Zero (Offset) error:Adjustable to ±1 LSB
Gain (Full-scale) error:Adjustable to
±1 LSB
5µs (to 4 LSB of FSR)
20 V/µs
10 ppm/.
±20 mA
0.1 Ω max.
Digital Input /Output
 Input Channels
 Output Channels
 Number of Ports
16
16
2
Low
High
Low
High
High
Input Voltage
Output Voltage
0.8 V max.
2.0 V min.
0.5 V max. @ +24 mA (sink)
2.4 V min. @ -15 mA (source)
2.0 V min.
Counter/Timer
 Counter Chip
 Channels
82C54 or equivalent
3 channels, 2 channels are permanently configured
as programmable pacers; 1 channel is free for user
application
16-bit counter
Cascade as a 32-bit clock divider for pacer clock for
A/D conversion
16-bit
Channel 1: 10 MHz
Channel 2: Takes input from output of channel 1
Channel 0: Internal 100 kHz or external
TTL level
 Counter 0
 Counter 1, 2
 Resolution
 Base Clock
 Compatibility
Clock Input
Gate Input
Counter Output
Low
High
Low
High
Low
High
Power Consumption
Temperature
 Relative Humidity
 Certifications
AI0
AI2
AI4
AI6
AI8
AI10
AI12
AI14
AIGND
AO0_REF
AO0_OUT
AOGND
DI0
DI2
DI4
DI6
DI8
DI10
DI12
DI14
DGND
DO0
DO2
DO4
DO6
DO8
DO10
DO12
DO14
DGND
CNT0_CLK
CNT0_OUT
CNT0_GATE
+12V
 PCI-1741U
 PCL-10168
Max.
Operation
Storage
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AI1
AI3
AI5
AI7
AI9
AI11
AI13
AI15
AIGND
AO1_REF
AO1_OUT
AOGND
DI1
DI3
DI5
DI7
DI9
DI11
DI13
DI15
DGND
DO1
DO3
DO5
DO7
DO9
DO11
DO13
DO15
DGND
PACER_OUT
TRG_GATE
EXT_TRG
+5V
Ordering Information
68-pin SCSI-II female
175 x 100 mm (6.9” x 3.9”)
Typical
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
 PCL-10168-2
+5 V @ 850 mA
+12 V @ 600 mA
+5 V @ 1 A
+12 V @ 700 m A
0 ~ 60 °C (32 ~ 158 °F)
(refer to IEC 68-2-1, 2)
-20 ~ 70 °C (-4 ~ 185 °F)
 ADAM-3968
 PCLD-8710
 PCI-1741S
200 kS/s, 16-bit, 16-ch High-Resolution Multifunction
Card, user’s manual and driver CD-ROM. (cable not
included)
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 1m.
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 2m.
68-pin SCSI-II Wiring Terminal Board for DIN-rail
Mounting
Industrial Wiring Terminal Board with CJC circuit for
DIN-rail Mounting. (cable not included)
PCI-1741U with PCLD-8710 and PCL-10168 cable
IPPC
TPC
FPM
ATM & AWS
DA&C
cPCI
ADAM-3000
Motion Control
ICOM
eConnectivity
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
5 ~ 95%RH non-condensing (refer to IEC 68-2-3)
CE certified
.
Online Download www.advantech.com/products
All product specifications are subject to change without notice
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
UNO
0.8 V max.
2.0 V min.
0.8 V max.
2.0 V min.
0.5 V max. @ +24 mA (sink)
2.4 V min. @ -15 mA (source)
General
 I/O Connector Type
 Dimensions
Pin Assignments
Last updated : January 2005
6-21
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-22
PCI-1747U
250 kS/s, 16-bit, 64-ch Analog Input Card
Features
NEW
 16-bit high resolution
 250 kS/s sampling rate
 64 S.E. or 32 Diff. AI, or a combination
 Auto calibration function
 Unipolar/Bipolar input range
 1k samples FIFO for AI
 Bus master DMA data transfer
 Universal PCI Bus
 BoardID™ switch
Introduction
PCI-1747U is a high-resolution high channel count analog input card for the PCI bus. Its sampling rate is up to 250 kS/s and 16-bit resolution provides the power needed for most
data acquisition applications. PCI-1747U provides 64 single-ended, 32 differential analog input channels or a combination of these. It also has built in a 1k-sample FIFO buffer for
analog input data.
Specifications
 Resolution
 Base Clock
Analog Input




Channels
Resolution
FIFO Size
Max. Sampling Rate
Input range and
Gain List
Bandwidth for
PGA




64 single-ended or 32 differential or combination
16-bit
1 K samples
250 kS/s
Gain
Unipolar
Bipolar
Gain
Bandwidth
Common mode voltage
Max. Input voltage
Input Protect
Input Impedance
0.5
N/A
±10
0.5
4.0
MHz
2
0~5
±2.5
2
2.0
MHz
4
0~2.5
±1.25
4
1.5
MHz
8
0~1.25
±0.625
8
0.65
MHz
±11 V max. (operational)
±20 V
30 Vp-p
100 MΩ/10pF(Off); 100 MΩ/100pF(On)
DC
Accuracy
AC
Clocking and
Trigger Inputs
1
0~10
±5
1
4.0
MHz
Trigger Mode
A/D pacer clock
DNLE: ±1LSB
INLE: ±1LSB
Zero (Offset) error: Adjustable to ±1 LSB
Gain
0.5
1
2
4
8
Gain error
0.03 0.02 0.02 0.03 0.04
(% FSR)
THD: -90 dB
ENOB: 13.5 bits
Software, on-board programmable pacer
or external
250 kHz (max.); 2.328mHz (min.)
Counter/Timer
 Counter chip
 Channels
 Counter 0
 Counter 1, 2
16-bit
Channel 1: 10 MHz
Channel 2: Takes input from output of channel 1
Channel 0: Internal 100 kHz
16-bit timer
Cascade as a 32-bit clock divider for pacer clock for
A/D conversion
General
 I/O Connector Type
 Dimensions
Power Consumption
Temperature
 Relative Humidity
 Certifications
68-pin SCSI-II female
175 x 100 mm (6.9” x 3.9”)
Typical
Max.
Operating
Storage
+5 V @ 850 mA
+12 V @ 600 mA
+5 V @ 1 A
+12 V @ 700 m A
0 ~ 60 °C (32 ~ 158 °F)
(refer to IEC 68-2-1,2)
-20 ~ 70°C (-4 ~ 185°F)
5 ~ 95%RH non-condensing (refer to IEC 68-2-3)
CE certified
Ordering Information:
 PCI-1747U
 ADAM-3968
 PCL-10168
 PCL-10168-2
250 kS/s, 16-bit, 64-ch, analog input universal PCI
bus card
68-pin SCSI cable wiring terminal for DIN-rail
mounting
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 1m.
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 2m.
82C54 or equivalent
3 channels, 2 channels are permanently configured
as programmable pacers; 1 channel is for internal use
only
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1747U
Feature Details
Pin Assignments
Auto-Calibration Function
The PCI-1747U provides an auto-calibration function with an calibration utility. The builtin calibration circuitry of the PCI-1747U corrects gain and offset errors in analog input,
thereby eliminating the need for external equipment and user adjustments.
On-Board Programmable Timer/Counter
PCI-1747U provides a programmable timer counter for generating a pacer trigger for the
A/D conversion. The timer/counter chip is 82C54, which includes three 16-bit counter
10 MHz clocks. One counter is used as an event counter for counting events coming
from the input channel. The other two are cascaded together to make a 32-bit timer for
pacer trigger time base.
Plug & Play Function
The PCI-1747U is a Plug & Play device, which fully complies with PCI Specification Rev
2.2. During card installation, there is no need to set jumpers or DIP switches. Instead,
all bus-related configurations such as base I/O address and interrupt are automatically
done by the Plug & Play function.
Automatic Channel/Gain/SD/BU Scanning
The PCI-1747U features an automatic channel/gain/SD/BU scanning circuit. This circuit
controls multiplexer switching during sampling in a way that is more efficient than
software implementation. An on-board SRAM stores different gain, SD (Single-Ended/
Differential) and BU (Bipolar/Unipolar) values for each channel. This combination lets
users perform multi-channel high-speed sampling with different gain, SD and BU values
for each channel.
PCI-Bus Mastering Data Transfer
PCI-1747U supports PCI-Bus mastering DMA for high-speed data transfer and gap-free
analog input and analog output. By setting aside a block of memory in the PC, the PCI1747U performs bus-mastering data transfers without CPU intervention, setting the CPU
free to perform more urgent tasks such as data analysis and graphics manipulation. The
function makes it possible to run all I/O functions simultaneously at full speed without
losing data.
On-board FIFO Memory
AI0
AI2
AI4
AI6
AI8
AI10
AI12
AI14
AGND
AI16
AI18
AI20
Ai22
AI24
AI26
AI28
AI30
AI32
AI34
AI36
AI38
AI40
AI42
AI44
AI46
AGND
AI48
AI50
AI52
AI54
AI56
AI58
AI60
Ai62
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AI1
AI3
AI5
AI7
AI9
Ai11
AI13
AI15
AGND
AI17
AI19
AI21
AI23
AI25
AI27
AI29
AI31
AI33
AI35
AI37
AI39
AI41
AI43
AI45
AI47
AGND
AI49
AI51
AI53
AI55
AI57
AI59
AI61
Ai63
PCI-1747U provides 1K samples on-board FIFO (First In First Out) memory buffer for
AD. This is an important feature for faster data transfer and more predictable performance
under the Windows system.
IPPC
TPC
FPM
ATM & AWS
DA&C
cPCI
ADAM-3000
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-23
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-24
PCI-1713
100 kS/s, 12-bit, 32-ch,
Isolated Analog Input Card
Features
 2500 VDC isolation protection
 32 single-ended or 16 differential analog inputs, or a combination
 12-bit resolution for A/D conversion
 Up to 100 kS/s sampling rate for A/D conversion
 Programmable gain for each input channel
 On-board 4 K samples FIFO buffer
 S/W, internal or external pacer triggering supported
Introduction
The PCI-1713 is an isolated high-speed analog input card for the PCI bus. It provides 32 analog input channels with a sampling rate up to 100 kS/s, 12-bit resolution and isolation
protection of 2500 VDC.
Specifications
General
Analog Input
 Channels
32 single-ended or 16 differential
(software programmable)
12-bit
4K samples
Bipolar: ±10 V, ±5 V, ±2.5 V, ±1.25 V, ±0.625 V
Unipolar: 0 ~10 V, 0 ~ 5 V, 0 ~ 2.5 V, 0 ~ 1.25 V
±30 V
 Resolution
 Onboard FIFO
 Input Range
(software programmable)
 Maximum Input
Overvoltage
 Common Mode
Gain CMRR
Rejection Ratio(CMRR) 0.5, 1 75dB
2
80dB
4
84dB
8
84dB
 Maximum Sampling
100 kS/s
Rate
 Accuracy
Gain Accuracy
(depends on gain)
0.5, 1 0.01% of FSR±1LSB
2
0.02% of FSR±1LSB
4
0.02% of FSR±1LSB
8
0.04% of FSR±1LSB
 Linearity Error
±1 LSB
 Input Impedance
 Trigger Mode
1 GΩ
Software, on-board programmable pacer or external
(TTL level)
 I/O Connector
 Dimensions (L x H)
 Power Consumption
37-pin D-type female connector
175 x 100 mm (6.9" x 3.9")
+5 V @ 850 mA (Typical),
+5 V @ 1.0 A (Max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
Ordering Information
 PCI-1713





PCLD-881B
ADAM-3937
PCL-10137-1
PCL-10137-2
PCL-10137-3
100 kS/s, 12-bit, 32-channel Isolated Analog Input
Card, user’s manual and driver CD-ROM. (cable not
included)
Industrial Wiring Terminal Board (cable not included)
Wiring Terminal Board
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Applications
 Signal isolation
 Process monitoring and control
 Transducer/sensor interfacing
 Multi-channel DC voltage measurement
Programmable Pacer
 Timer
 Time Base
32-bit programmable timer
10 MHz
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1714
PCI-1714UL
30 MS/s Simultaneous 4-ch Analog Input Card
10 MS/s Simultaneous 4-ch Analog Input Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 12-bit A/D converter up to 30 MS/s
 4 single-ended analog input channels
 Programmable gain for each input channel
 32 K samples on board FIFO memory
 4 A/D converters simultaneously sampling
 Multiple A/D triggering modes
 Programmable pacer/counter
 BoardID™ switch
IPPC
TPC
FPM
ATM & AWS
DA&C
Introduction
The PCI-1714 is an advanced-performance data acquisition card based on 32-bit PCI bus architecture. The maximum sampling rate of PCI-1714 is up to 30 MS/s, with an emphasis
on continuous, non-stop, high-speed, streaming data of A/D samples to host memory.
cPCI
ADAM-3000
Specifications
Analog Input
 Channels
 Resolution
 FIFO Size
 Max. Sampling Rate
Accuracy
4 single-ended analog input channels
12 bits
32 K samples/ch for PCI-1714
8 K samples/ch for PCI-1714UL
30 MS/s for PCI-1714
10 MS/s for PCI-1714UL
External Clock 1
External Clock 0
General
External Trigger 0
 I/O Connector Type
4 BNC connector (for AI)
1 PS2 connector (for Ext. clock and trig)
 Dimensions
137 x 107 mm (5.4” x 4.2”)
 Power Consumption
Typical +5 V @ 850 mA ; +12 V @ 600 mA
Max.
+5 V @ 1 A ; +12 V @ 700m A
 Operating Temperature 0 ~ 70° C (32~158° F)
 Storage Temperature -20 ~ 85° C (-4~185° F)
 Relative Humidity
5 ~ 95%RH non-condensing (refer to IEC 68-2-3)
 Certifications
CE
Analog Input:
Channels
Resolution
FIFO Size
Max. Sampling Rate1
Input range and
Gain List
Drift
Small Signal
Bandwidth for PGA
Max. Input voltage
Input Impedance
Trigger Mode
Accuracy
4 single-ended analog input channels
12-bit
32K locations (8K for PCI-1714UL)
30MHz 10MHz for PCI-1714UL
Gain
1
2
5
10
Range
±5V
±2.5V
±1V
±0.5V
Gain
1
2
5
10
Zero (µV/° C)
±30
±30
±30
±30
Gain (ppm//° C)
±30
±30
±30
±30
Gain
1
2
5
10
Bandwidth (-3dB)
7 MHz
7 MHz
7 MHz
7 MHz
±15 V
Input Surge Protect
30 Vp-p
50Ω/1MΩ/Hi Z jumper selectable /100pF
Software, pacer, post-trigger, pre-trigger, delay-trigger, about-trigger
±1LSB (No Missing Codes:12 Bits
DNLE
Guaranteed)
INLE
±2LSB
DC
Offset error
Adjustable to ±1LSB
Gain error
Adjustable to ±1LSB
External Analog
Trigger Input
AC
Logic level
Input impedance
Input coupled
Frequency
Logic level
Input impedance
Input coupled
Frequency
Logic level
Input impedance
Input coupled
Range
Resolution
Frequency
SINAD
68 dB
S/(N+D)
ENOB
11bits
THD
-75 dB
TTL (Low: 0.8 V max. High: 2.0 V min.)
50 Ω
DC
Up to 30 MHzUp to 10 MHz for PCI-1714UL
5.0V peak to peak sin wave
Hi Z
AC
Up to 30 MHzUp to 10 MHz for PCI-1714UL
TTL (Low: 0.8 V max. High: 2.0V min.)
Hi Z
DC
By analog input range
8-bit
Up to 1MHz
Ordering Information
 PCI-1714





PCI-1714UL
ADAM-3909
PCL-10901-1
PCL-10901-3
PCL-1010B-1
30 MHz Simultaneous 4-ch Analog Input Card, user's
manual and driver CD-ROM (PCL-10901-1 cable
included)
10MHz Simultaneous 4-ch Analog Input card
DB-9 Wiring Terminal for DIN-rail Mounting
PS2 to DB9 Wiring Cable, 1m
PS2 to DB9 Wiring Cable, 3m
BNC to BNC Wiring Cable, 1m
Pin Assignments
Online Download www.advantech.com/products
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
6-25
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-26
PCI-1720
PCI-1720U
4-ch Isolated Analog Output Card
4-ch Universal Isolated Analog Output Card
Features
 Four 12-bit D/A output channels
 Multiple output ranges
 2,500 VDC isolation between the outputs and the PCI bus
 Keeps the output settings and values after system reset
 One DB37 connector for easy wiring
 Universal PCI and BoardID switch (PCI-1720U only)
Introduction
The PCI-1720 provides four 12-bit isolated digital-to-analog outputs for the PCI bus. With isolation protection of 2500 VDC between the outputs and the PCI bus, the PCI-1720 is
ideal for industrial applications where high-voltage protection is required.
Keeping the Output Settings and Values after System Reset
Users can independently set the four outputs to different ranges: 0 to +5 V, 0 to +10 V, ±5 V, ±10 V, 0 to 20 mA (sink) or 4 to 20 mA (sink). When the system is hot reset, (power is
not shut off), the PCI-1720 can either retain the last analog output settings and values, or return to its default configuration, depending on jumper setting. This practical function
eliminates danger caused by misoperation during an unexpected system reset.
PCI-Bus Plug & Play
The PCI-1720 uses a PCI controller to interface the card to the PCI bus. The controller fully implements the PCI bus specification Rev 2.1. All bus relative configurations, such as
base address and interrupt assignment, are automatically controlled by software.
Specifications
 PCI-1720U
 Channels
 Resolution
 Output Range
 ADAM-3937
 PCLD-880













4 isolated D/A channels
12 bits
Unipolar: 0 ~ +5 V, 0 ~ +10 V
Bipolar: ±5 V, ±10 V
Current loop (sink): 0~ 20 mA, 4 ~ 20 mA
Throughput
15 kHz min. @ full-scale output range
Accuracy
±0.024%
Isolation Voltage
2,500 VDC between the outputs and the PCI bus
Temperature Drift
Typical: 10 PPM/° C (0 ~ 60° C) (32 ~ 140° F)
Maximum: 20 PPM/° C (0 ~ 60° C) (32 ~ 140° F)
Output Drive
±5 mA max.
Current Loop Excitation 50 V (max.)
Voltage
On-board 12 VDC
80 mA (max.)
Excitation Voltage
Power Consumption
+5 V @ 350 mA (typical), 500 mA (max.)
+12 V @ 200 mA (typical), 350 mA (max.)
Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)
Storage Temperature -20 ~ +70° C (-4 ~ 158° F)
Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
Connector
DB-37 connector
Dimensions (L x H)
175 x 100 mm (6.9" x 3.9")
4-channel Isolated Output Card, user's manual and
driver CD-ROM. (cable not included)
DB37 Wiring terminal for DIN-rail mounting
Screw terminal board
Applications




Process control
Programmable voltage source
Programmable current sink
Servo control
Pin Assignments
Ordering Information
 PCI-1720
 PCL-10137-1
 PCL-10137-2
 PCL-10137-3
4-channel Isolated Output Card, user's manual and
driver CD-ROM. (cable not included)
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1721
12-bit, 4-ch Advanced
Analog Output Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 10 MHz maximum digital update rate
 PCI-bus mastering for data transfer
IPPC
 Auto calibration function
 Four analog output channels with 1 K FIFO
 A 12-bit DAC is equipped for each of analog output channels
 Real-time waveform output function with internal/external pacer
 Synchronized output function
 Flexible output types and range settings
TPC
FPM
 Keeps the output settings and values after system reset
 16-ch DI/O and one 10 MHz 16-bit resolution counter
ATM & AWS
 BoardID™ switch
DA&C
Introduction
The PCI-1721 is an advanced high-speed analog output card for PCI bus, and each of analog output channels are equipped with a 12-bit, double-buffered DAC. It features many
powerful and unique functions, like a waveform output function with 10 MHz maximum update rate, auto-calibration and a BoardID switch. The PCI-1721 is an ideal solution for
industrial applications where high-speed continuous analog output or real-time waveform output functions are required.
Specifications
Analog Output




Channels
Resolution
FIFO Size
Operation Mode
Output Range
(Internal & External
Reference)
Accuracy






Offset
Slew Rate
Driving Capability
Output Impedance
Max. Updata Rate
Settling Time
External Clock Input
(Max. 10 MHz)
External TTL Trigger
Input
Counter/Timer




Channels
Resolution
Compatibility
Base Clock
 Max. Input Frequency
Low
High
Low
High
Low
High
Clock Input
4
12-bit
1 K Samples
Single/ Continuous/ Wavefrom /Synchronized output
Using Internal
Reference
Using External
Reference
Relative
Differential Nonlinearity
0 ~ +5 V, 0 ~ +10 V, -5 ~ +5 V,
-10 ~ +10 V,
0 ~ 20 mA, 4 ~ 20 mA
0 ~ +x V @ +x V (-10 ≤ x ≤ 10)
-x ~ +x V @ +x V (-10 ≤ x ≤ 10)
±1 LSB
±1 LSB (monotonic)
1
16-bit
TTL level
10 MHz
10 MHz
Counter Output
General
I/O Connector
Type
Dimensions
Power
Consumption
Temperature
68-pin SCSI-II female
Typical
Max.
Operation
Storage
Relative
Humidity
Certifications
<1 LSB
10 V/µs
±10 mA
0.1Ω max.
10 MHz (max. for one channel)
5 µs (to ±1/1 LSB of FSR)
Low
High
Low
High
Gate Input
0.8 V max.
2.0 V min.
0.8 V max.
2.0 V min.
0.4 V max. @ +2.5 mA
3.0 V min. @ -2.5 mA
175 x 100 mm (6.9” x 3.9”)
+5 V @ 850 mA, +12 V @ 600 mA
+5 V @ 1 A, +12 V @ 700 mA
0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)
-20 ~ 85° C (-4 ~ 185° F)
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
CE certified
Digital Input /Output
Input Voltage
Input Load
16 (bi-directional)
2
Low
High
Low
High
0.8 V max.
2.0 V min.
0.5 V max.@ +24 mA (sink)
2.0 V min.@ -15 mA
(source)
Ordering Information
 PCI-1721
 PCL-10168
 ADAM-3968
ADAM-3000
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
Input Channels
Number of Ports
0.8 V max.
2.0 V min.
0.8 V max.
2.0 V min.
cPCI
ADAM-6000
ADAM-8000
BAS
12-bit, 4-ch Advanced Analog Output Card, user’s
manual and driver CD-ROM. (cable not included)
68-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction,
1 and 2 m
68-pin SCSI-II Wiring Terminal Board for DIN-rail
Mounting
Online Download www.advantech.com/products
6-27
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-28
PCI-1723
16-bit, 8-ch Non-isolated
Analog Output Card
Features
 Auto calibration function
 A 16-bit DAC is equipped for each analog output channel
 Synchronized output function
 Output values retained after system hot reset
 2-port (16-channel) user-defined digital input/output
 BoardID™ switch
Introduction
The PCI-1723 is a non-isolated multiple channel analog output card for the PCI bus, and each analog output channel is equipped with a 16-bit, double-buffered DAC. It also features
an auto-calibration function and a BoardID™ switch.. The PCI-1723 is an ideal solution for industrial applications where multiple analog output channels are required.
Specifications
Ordering Information
Analog Output
 PCI-1723
 PCL-10168




Output Channels
Resolution
Operation Mode
Output Range
 Accuracy




Offset
Output Impedance
Throughput
Settling time
8
16-bit
Single output, Synchronized output
-10 ~ +10 V, 0 ~ 20 mA, 4 ~ 20 mA
(Internal Reference only)
Relative
±6 LSB
Differential Non-linearity
±6 LSB (monotonic)
< 6 LSB
0.1 Ω max.
PC dependent, Software update (direct AO)
50 µs (to ±6 LSB of FSR)
 ADAM-3968
16-bit, 8-ch Non-isolated Analog Output Card
68-pin SCSI-II cable with male connectors on both ends
and special shielding for noise reduction, 1 and 2m
68-pin SCSI-II Wiring Terminal Board for DIN-rail
mounting
Applications
 Process control, Programmable voltage source, Programmable current sink,
Servo control, Multiple loop PID control, V-command motion control
Pin Assignments
Digital Input/Output
 Channels
 Number of Ports
 Input Voltage
 Output Voltage
16 (bi-directional)
2
Low 0.8 V max.
High 2.0 V min.
Low 0.5 V max. @ 24 mA (sink)
High 2.4 V min. @ -15 mA (source)
General
 I/O Connector Type
 Dimensions
 Power Consumption
68-pin SCSI-II female
175 x 100 mm (6.9” x 3.9”)
Typical +5 V @ 850 mA, +12 V @ 600 mA
Max.
+5 V @ 1 A, +12 V @ 700 mA
 Operating Temperature 0 ~ 60° C (32 ~ 158° F) (IEC 68-2-1,2)
 Storage Temperature -20 ~ 85° C (-4 ~ 185° F)
 Relative Humidity
5 ~ 95 % RH non-condensing (IEC 68-2-3)
 Certifications
CE
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1724U
14-bit, 32-ch Isolated
Analog Output Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 High-density 32-channel analog output channels
 Flexible Output Range: +/-10 V, 0 ~ 20 mA and 4 ~ 20 mA
 Synchronized output function
 Keeps output values after system hot reset
 BoardID™ switch
IPPC
TPC
FPM
ATM & AWS
DA&C
Introduction
The PCI-1724U is an isolated high-density multiple channel analog output card for the PCI bus, where each analog output channel is equipped with a 14-bit DAC. It feaures optional
voltages, current output and a BoardID™ switch. The PCI-1724U is an ideal solution for industrial applications where multiple analog output channels are required.
Specifications




Channels
Resolution
Operation Mode
Output Range
 Accuracy





Offset
Output Impedance
Throughput
Settling Time
Isolation
32 ch isolation
14-bit
Single output, synchronized output
-10 ~ +10 V, 0 ~ 20 mA, 4 ~ 20 mA
(Internal Reference only)
Relative
+/- 4 LSB
Differential Non-linearity +/- 2 LSB (monotonic)
< 2 LSB
0.1 Ω max.
PC dependent, Software update (Direct AO)
60 µs
1,500 VDC system isolation
I/O Connector Type
Dimensions (L x H)
Operating Temperature
Storage Temperature
Operating Humidity
Process control
Programmable voltage source
Programmable current sink
Servo control
Multiple loop PID control
V-command motion control
Motion Control
ICOM
Pin Assignments
eConnectivity
UNO
AO8
AGND
AO9
One 62-pin D-type connector
175 x 100 mm (6.9” x 3.9”)
0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)
-20 ~ 70° C (-4 ~ 158° F)
5 ~ 95 % RH non-condensing (refer to IEC 68-2-3)
AGND
AO10
AGND
AO11
AGND
AO12
AGND
Ordering Information
 PCI-1724U
 PCI-10162
 ADAM-3962






AGND
General





ADAM-3000
Applications
Analog Output
cPCI
AO13
14-bit, 32-ch Isolated Analog Output Card
DB62 Cable Assembly (1m, 3m)
DB62 Cable Wiring Terminal for Din-Rail Mounting
AGND
AO14
AGND
AO15
AGND
AGND
AGND
AGND
NC
AGND
AO0
AGND
AO1
AGND
AO2
AGND
AO3
AGND
AO4
AGND
AO5
AGND
AO6
AGND
AO7
AO24
AO25
AO26
AO27
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Online Download www.advantech.com/products
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
AO16
AGND
AO17
AGND
AO18
AGND
AO19
AGND
AO20
AGND
AO21
AGND
AO22
AGND
AO23
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
AO28
AO29
AO30
AO31
6-29
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-30
PCI-1727U
12-channel D/A output Card (ISA Compatible)
Features
NEW
 Compatible with PCL-727
 12 independent analog output channels
 Multiple output range, including 4~20mA current loop
 16 DI and 16 DO channels
 Fuse on each channel
 Universal PCI and BoardID™ switch
Introduction
The PCI-1727U provides twelve 14-bit analog output channels, and is pin-compatible with the ISA PCL-727 card. It supports both +/-10V and 0~ 20mA current loop (sink). The card’s
on board DC-to-DC converter ensures the full 10V D/A output is always available.
Each analog output channel has a built-in fuse to protect the circuit, PC and the external devices. The PCI-1727U is an ideal, economical solution for the applications which require
multiple PID control loops.
In addition to its analog outputs, the PCI-1727U provides 16 TTL DI and 16 TTL DO channels that are easily applied with industrial on/off control applications.
Specifications
Power Supply
Analog Output











Chipset
Channels
Resolution
Output Range
Current Loop
Excitation Voltage
Output Current in
Voltage Output
Throughput
Setting Time
Power on Default Value
Fuse on Each Channel
Calibration Function
ADI AD5390
12
14 bits
±10 V, 0 ~ 20 mA.
8 V ~ 36 V
15 mA max.
Software Static Update
<= 70 µs
All output ranges will output 0V or 0mA in power on
0.1A
Digital Input





Channels
Level
Logic0
Logic1
Input loading
16
TTL compatible
0.8 V max
2.0 V min
0.5 V @ 0.4 mA max. (low)
2.7 V @ 50 µA max (high)
Digital Output




Channels
Level
Logic0
Logic1
16
TTL compatible
0.5 V @ 8 mA (sink)
2.4 V @ 0.4 mA (source)
Plug-in DA&C Cards
 +5V
 +12V
 -12V
250 mA typical, 500 mA max
150 mA typical, 300 mA max
100 mA typical, 130 mA max
General





Connector
Dimensions
Operating Temperature
Storage temperature
Relative Humidity
37-pin D-type female
175 × 100 mm (6.9” ×3.9”)
0 ~ 50 °C
-20 ~ 65 °C
5 ~ 95%, non-condensing
Ordering Information







PCI-1727U
PCL-10120-1
PCL-10137-1
ADAM-3937
PCLD-780
PCLD-782
PCLD-785
12-channel D/A output Card
20-pin flat cable, 1m
DB37 cable assembly, 1m
DB37 wiring terminal for DIN-rail mounting
Two 20-pin screw terminal board
Opto-isolated D/I board
Relay output board
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1751
PCI-1751U
48-bit Digital I/O Card and Counter Card
48-bit Universal Digital I/O and Counter Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 48 TTL digital I/O lines
 Emulates mode 0 of 8255 PPI
 Buffered circuits for higher driving capacity than 8255
 Interrupt handling
 Timer/Counter interrupt capability
IPPC
TPC
 Supports both dry and wet contact
 Keeps the I/O port setting and DO state after system reset
 Universal PCI & BoardID switch (PCI-1751U only)
FPM
ATM & AWS
DA&C
Introduction
PCI-1751 is a 48-bit digital I/O card for the PCI bus. Its 48 bits are divided into six 8-bit I/O ports and users can configure each port as input or output via software. The PCI-1751
also provides one event counter and two 16-bit timers, which can be cascaded to become a 32-bit timer.
Fulfilling the True Requirements of Industrial Applications
With two practical functions, the PCI-1751 fulfills the true requirements of industrial applications. When the system is hot reset, (power is not shut off), the PCI-1751 can either
retain the last I/O port setting and output value, or reset to its default configuration, depending on jumper settings. This function protects the system from wrong operations during
unexpected system resets. Additionally, the PCI-1751 supports both dry and wet contacts so that it can easily interface with other devices.
Interrupt Handling Capability
cPCI
ADAM-3000
Motion Control
Two lines in each I/O port (C0 and C4) and two of the three counter outputs (Timer 1 and Counter 2) are connected to the interrupt circuitry. Two interrupt request signals can be
generated at the same time and the software can service the two request signals by ISR. Moreover, a pin in the connector can output a digital signal simultaneously with the card
ICOM
generating an interrupt, and users can utilize this function to trigger external devices with the interrupt.
Specifications
 I/O Channels
 Programming Mode
Ordering Information
48 digital I/O lines
8255 PPI mode 0
 PCI-1751
 PCI-1751U
Digital Output
 Logic Level 0
 Logic Level 1
0.4 V max. @ 24 mA (sink)
2.4 V min. @ 15 mA (source)
 PCL-10168
 ADAM-3968
Digital Input
 Logic Level 0
 Logic Level 1
0 ~ 0.8 V
2 ~ 5.25 V
 ADAM-3968/20
Programmable timer/counter
 Frequency Range
 Counters
 ADAM-3968/50
0 ~ 10 MHz
Two 16-bit counters or one 32-bit counter
One 16-bit event counter
 PCLD-8751
 PCLD-8761
General
 Power Consumption
5 V @ 850 mA (typical)
5 V @ 1.0 A (max.)
 Operating Temperature 0 ~ 70° C (32 ~ 158° F)
 Storage Temperature -20 ~ 80° C (-4 ~ 176° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
 Connectors
68-pin SCSI-II female connector (Centronics type)
 Dimensions (L x H)
175 x 100 mm (6.9" x 3.9")
Applications





Industrial AC/DC I/O monitoring and controlling
Relay and switch monitoring and controlling
Parallel data transfer
TTL, DTL and CMOS logic signal sensing
Indicator LED driving
eConnectivity
48-bit digital I/O card and Counter Card, user’s manual
and driver CD-ROM. (cable not included)
48-bit universal digital I/O card and Counter Card,
UNO
user’s manual and driver CD-ROM. (cable not included)
68-pin SCSI cable, 1 and 2m
68-pin SCSI cable wiring terminal for DIN-rail
mounting
ADAM-4000
68-pin SCSI-II to three 20-pin Wiring Terminal Module
for DIN-Rail Mounting
68-pin SCSI to 2 x 50-pin box headers converter
ADAM-5000
module
48-ch Isolated DI Board
24-ch Replay and 24-IDI Board
Pin Assignments
PA00
PA01
PA02
PA03
PA04
PA05
PA06
PA07
GND
PB00
PB01
PB02
PB03
PB04
PB05
PB06
PB07
GND
PC00
PC01
PC02
PC03
PC04
PC05
PC06
PC07
GND
CNT0_OUT
GND
CNT1_OUT
GND
CNT2_OUT
INT_OUT
VCC
ADAM-6000
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Online Download www.advantech.com/products
PA10
PA11
PA12
PA13
PA14
PA15
PA16
PA17
GND
PB10
PB11
PB12
PB13
PB14
PB15
PB16
PB17
GND
PC10
PC11
PC12
PC13
PC14
PC15
PC16
PC17
GND
CNT0_CLK
CNT0_G
CNT1_CLK
CNT1_G
CNT2_CLK
CNT2_G
VCC
ADAM-8000
BAS
6-31
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-32
PCI-1753
PCI-1753E
96-ch Digital I/O Card
96-ch Digital I/O Extension Card for PCI-1753
Features
 Up to 192 (96+96) TTL digital I/O lines
 Emulates mode 0 of 8255 PPI
 Buffered circuits for higher driving capacity than 8255
 Multiple-source interrupt handling
 Interrupt output pin for simultaneously triggering external devices with the
interrupt
 Output status read-back
 “Pattern match” and “Change of state” interrupt functions for critical I/O
monitoring
 Keeps I/O setting and digital output values when hot system reset
 Supports dry contact and wet contact
 High-density 100-pin SCSI connector
PCI-17153
PCI-1753E
Introduction
PCI-1753 is a 96-bit digital I/O card for the PCI bus, which can be extended to 192 digital I/O channels by connecting with its extension board, PCI-1753E. The card emulates mode
0 of the 8255 PPI chip, but the buffered circuits offer a higher driving capability than the 8255. The 96 I/O lines are divided into twelve 8-bit I/O ports: A0, B0, C0, A1, B1, C1, A2,
B2, C2, A3, B3 and C3. You can configure each port as input or output via software.
Specifications
Pin Assignments
 I/O Channels
96 digital I/O lines for PCI-1753
192 digital I/O lines if extending with PCI-1753E
 Programming Mode
8255 PPI mode 0
 Input Signal
logic level 0: 0.8 V max.
logic level 1: 2.0 V min.
 Output Signal
logic level 0: 0.44 V max. @ 24 mA (sink)
logic level 1: 3.76 V min. @ 24 mA (source)
 Power Consumption
+5 V @ 400 mA (typical)
+5 V @ 2.7 A (max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F) (refer to IEC 68-2-3)
 Operating Humidity
5 ~ 95% RH non-condensing
 Connector
One 100-pin SCSI female connector (Centronics™
type)
 Dimensions (L x H)
175 x 100 mm (6.9" x 3.9")
Ordering Information
 PCI-1753
 PCI-1753E
 PCL-10268
 ADAM-3968
 ADAM-3968/20
 ADAM-3968/50
 PCLD-8751
 PCLD-8761
96 ch. Digital I/O Card, user’s manual and driver
CD-ROM. (cable not included)
Extension Board for PCI-1753
100-pin to 2x68-pin SCSI cable, 1 and 2m
(PCL-10268 100-pin SCSI-II male connector P/N:
16549A0000)
68-pin SCSI wiring terminal for DIN-rail mounting
68-pin SCSI-II to Three 20-pin Wiring Terminal
Module for DIN-Rail Mounting
68-pin SCSI wiring terminal for DIN-rail mounting
48-ch Isolated DI Board
24-ch Replay and 24-IDI Board
Applications





Industrial AC/DC I/O devices for monitoring and controlling
Relay and switch monitoring and controlling
Parallel data transfer
TTL, DTL and CMOS logic signal sensing
Indicator LED driving
Plug-in DA&C Cards
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1755
Ultra-Speed 32-ch Digital I/O Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Bus-mastering DMA data transfer with scatter gather technology
 32/16/8-bit Pattern I/O with start and stop trigger function, 2 modes
Handshaking I/O Interrupt handling capability
 On-board active terminators for high speed and long distance transfer
 Pattern match and Change state detection interrupt function
IPPC
TPC
 General-purpose 8-ch DI/O
FPM
ATM & AWS
DA&C
Introduction
The PCI-1755 supports PCI-bus mastering DMA for high-speed data transfer. By setting aside a block of memory in the PC, the PCI-1755 performs bus-mastering data transfers
without CPU intervention, setting the CPU free to perform other more urgent tasks such as data analysis and graphic manipulation. The function allows users to run all I/O functions
simultaneously at full speed without losing data.
Specifications
Channels
Number of Ports
Messaging
32 TTL compatible
Port A, Port B, Port C and Port D (8 bits/port)
32DI (PA~PD) (default); 32DO (PA~PD); 16DI (PA~PB) & 16DO (PC~PD); 8DI (PA) & 8DO
I/O Configuration
(PC) (Programmable)
16 KB for DI & 16 KB DO channels
On-board FIFO
Data Transfer
Bus Mastering DMA with Scatter-Gather
Mode
Data Transfer
8/16/32 bits (programmable)
Bus Width
DI: 80 M bytes/sec, 32-bit @ 20 MHz
Transfer
120 M bytes/sec, 32-bit @ 40 MHz external pacer when data length
Characteristics
Max. Transfer
is less than FIFO size
Rate
DO: 80 MBytes/sec, 32-bit @ 20 MHz
Operation
Handshaking
Mode
I/O
Samples No.
Finite transfer, Continuous I/O
Direction
Synchronous
Burst Handshaking
Asynchronous 8255 Emulation
Handshaking Mode Clock source Internal: 30 MHz, 20 MHz, 15 MHz, 12 MHz, 10 MHz, Timer#0 for DI &
Timer#1
for
DO
for Burst
Handshaking External: EXT_CLKIN for DI & EXT_CLKOUT for DO
Data Acquisition at a predetermined rate by internal/external clock
Input
Waveform Generation at a predetermined rate by internal/external clock
Output
Clock Source Internal: 30 MHz, 20 MHz, 15 MHz, 12 MHz, 10 MHz, Timer#0
for DI
External: EXT_CLKIN
Clock Source Internal: 30 MHz, 20 MHz, 15 MHz, 12 MHz, 10 MHz, Timer#1
Normal Mode
for DO
External: EXT_CLKOUT
Software command/Trigger signal occurred from DI_STR or DO_STR/
Start Mode
Pattern DI
Software command/Trigger signal occurred from DI_STP (for DI) or
Stop Mode
DO_STR (for DO)/Pattern DI/"Finite transfers"
Monitor the selected input channel and capture data whenever there is a transition on one
of the channels, and then issue a IRQ
Clock Source Internal: 30 MHz, 20 MHz, 15 MHz, 12 MHz, 10 MHz, Timer#0
Chang Detection
for DI
External: EXT_CLKIN
(DI only)
Software command/Trigger signal occurred from DI_STP/Pattern DI
Start Mode
Software command/Trigger signal occurred from DI_STP/ Pattern
Stop Mode
DI/"Finite transfers"
DI trigger
DI_STR, DI_STP DO trigger signal DO_STR, DO_STP
signal
0.8 V max.
High
2.0 V min.
Low
Rising or falling edge, or digital pattern (for DI only)
Trigger Type
Trigger Capability Pulse width for
10 ns min.
edge triggers
Pattern trigger
Detect pattern match or mismatch on user-selected data lines
detection
capabilities
On-board Schottky diode termination
Terminator
Input Voltage
Input Load
Output Voltage
Driving Capacity
Hysteresis
General-purpose
DI/O
Interrupt Source
The messages can be generated when1. A specified number of bytes have been transferred,
2. When a specified input pattern is matched, 3. When a measurement operation completes.
0 V min.;
2.0 V min.;
High
Low
0.8 V max.
5 V max.
Terminator OFF: TTL compatible
+0.5 V @ ±20 mA High
+2.7 V @ ±1 mA max.
Low
Terminator ON
Termination
Terminator
110 Ω
2.9 V
Voltage
Resistor
+0.5 V @ ±22.4
High
+2.7 V @ ±1 mA max.
Low
mA
0.5 V max.
High
2.7 V min.
Low
0.5 V max @ +48
High
2.4 V min. @ -15 mA (source)
Low
mA (sink)
Power Available at
+4.65 ~ +5.25 VDC @ 1A
500 mV
I/O connector
DI0 ~ DI7 (TTL compatible)
DI Channels
DO Channels DO0 ~ DO7 (TTL compatible)
DI0~7 and Timer#2, Pattern match and Change detection, DI FIFO overflow and DO FIFO
underflow, DI_STP and DO_STP
Pacer






Channels
Timer#0
Timer#1
Timer#2
Resolution
Base Clock
Temperature
Relative Humidity
ADAM-3000
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
Timer#0, Timer#1 and Timer#2
Timer pacer for digital input
Timer pacer for digital output
Interrupt source
16-bit
10 MHz
ADAM-5000
ADAM-6000
General
I/O Connector Type
Dimensions (L x H)
Power
Consumption
cPCI
100-pin SCSI-II female
175 x 100 mm (6.9” x 3.9”)
Terminator OFF: +5 V @ 1 A
Terminator OFF: +5 V @ 1 A
Typical
Max.
Terminator ON: +5 V @ 1 A
Terminator ON: +5 V @ 1 A
0 ~ 60° C (32 ~ 140° F)
Operating
Storage
-20 ~ 85° C (-4 ~ 185° F)
(refer to IEC 68-2-1,2)
5 ~ 95% RH non-condensing
(refer to IEC 68-2-3)
Cert.
FCC, CE certified
ADAM-8000
BAS
Ordering Information
 PCI-1755
 ADAM-39100
 PCL-101100-1
Ultra-speed 32-ch Digital I/O Card
PCI-1755 Wiring Terminal for DIN-rail Mounting
100-pin SCSI-II cable with male connectors on both
ends and special shielding for noise reduction, 1 m
Online Download www.advantech.com/products
6-33
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-34
PCI-1730
PCI-1733
PCI-1734
32-ch Isolated Digital I/O Card (ISA Compatible)
32-ch Isolated Digital Input Card (ISA Compatible)
32-ch Isolated Digital Output Card (ISA Compatible)
PCI-1730
PCI-1733
PCI-1734
Features
Features
Features
 32 isolated DIO ch. (16 inputs and 16 outputs)
 32 isolated, bidirectional digital input channels
 32 TTL-level DIO ch. (16 inputs and 16 outputs)
 High-voltage isolation (2,500 VDC)
 High output driving capacity
 Interrupt capacity
 Interrupt capability
 D-type connectors for isolated input channels
 Two 20-pin connectors for isolated digital I/O
channels and two for TTL digital I/O channels
 Reverse voltage protection for isolated input
channels (up to 24 VDC)
 32 isolated digital output channels
 High output driving capacity
 High-voltage isolation on output channels (2,500
VDC)
 High sink current on isolated output channels (200
mA/channel)
 Integral suppression diodes for inductive loads
 Wide output range (5 ~ 40 VDC)
 D-type connectors for isolated output channels
 D-type connector for isolated input and output ch.
Specifications
Specifications
Isolated Digital Input







Input Channels
Interrupt Inputs
Interrupt Levels
Input Voltage
Input Resistance
Optical Isolation
Throughput
16 (16-ch/group)
4 (IDIO, IDI1, DIO, DI1)
2-7
5 ~ 30 VDC
2.7 kΩ @ 1 W
2,500 VDC
10 kHz max.
Isolated Digital Output





Output Channels
Optical Isolation
Throughput
Supply Voltage
Sink Current
16 (16-ch/group)
2,500 VDC
10 kHz
5 ~ 40 VDC
200 mA max./channel
General
 I/O Connector Type
 Dimensions (L x H)




37-pin D-type female
185 x 100 mm
(7.3”x3.9”)
Power Consumption
Typical: +5 V @ 330 mA
Max: +5 V @ 500 mA
Operating Temperature 0 ~ 60° C (32 ~ 140° F)
Storage Temperature -20~70° C (-4~158° F)
Relative Humidity
5 ~ 95% (IEC 68-2-3)
non-condensing
Specifications
Isolated Digital Input
 Input Channels
 Interrupt Inputs






Interrupt Levels
Input Voltage
Input Voltage
Input Resistance
Optical Isolation
Throughput
Isolated Digital Output
32 (16-ch/group)
4 (IDIO, IDI1, IDI16,
IDI17)
2, 3, 5, 7, 10, 11, 12, 15
5 ~ 30 VDC
5 ~ 30 VDC
2.7 kΩ @ 1 W
2,500 VDC
10 kHz max.





 I/O Connector Type
 Dimensions (L x H)








37-pin D-type female
185 x 100 mm
(7.3” x 3.9”)
Power Consumption
Typical: +5 V @ 320 mA
Max: +5 V @ 500 mA
Operating Temperature 0 ~ 60° C (32 ~ 140° F)
Storage Temperature -20~70° C (-4~158° F)
Relative Humidity
5 ~ 95% (IEC 68-2-3)
non-condensing
32 (16-ch/group)
2,500 VDC
10 kHz
5 ~ 40 VDC
200 mA max./channel
General
General
 I/O Connector Type
 Dimensions (L x H)
Output Channels
Optical Isolation
Throughput
Supply Voltage
Sink Current
37-pin D-type female
185 x 100 mm
(7.3” x 3.9”)
Power Consumption
Typical: +5 V @ 330 mA
Max: +5 V @ 500 mA
Operating Temperature 0 ~ 60°C (32 ~ 140°F)
Storage Temperature -20~70° C(-4~158° F)
Relative Humidity
5 ~ 95% (IEC 68-2-3)
non-condensing
Ordering Information
Ordering Information
Ordering Information
 PCI-1730
 PCI-1733
 PCI-1734
Card, manual and driver
CD-ROM (cable not.
included.)
32-channel isolated
digital input card,
manual and driver
CD-ROM (cable not
included)
32-channel Isolated
digital output card,
user’s manual and driver
CD-ROM (cable not
included)
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1730
PCI-1733
PCI-1734
PCI-1730 Accessories







PCL-10120-1
PCL-10120-2
PCLD-782
ADAM-3920
PCLD-885
PCLD-785
PCLD-786
Pin Assignments
20-pin flat cable, 1m
20-pin flat cable, 2m
16-channel opto-isolated D/I board
20-pin flat cable wiring terminal for DIN-rail mounting
16-channel power relay (form A) output board
16-channel relay output board
8-channel SSR I/O module carrier board
IPPC
TPC
General Accessories






PCLD-780
PCLD-880
ADAM-3937
PCL-10137-1
PCL-10137-2
PCL-10137-3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
FPM
Universal screw terminal board
Universal screw terminal board
DB37 wiring terminal for DIN-rail mounting
DB37 cable, 1m
DB37 cable, 2m
DB37 cable, 3m
ATM & AWS
DA&C
Introduction
cPCI
The PCI-1730/1733/1734 cards offer isolated digital input channels as well as isolated
digital output channels with isolation protection up to 2,500 VDC, which makes them ideal
for industrial applications where high-voltage isolation is required. In addition, all output
channels are provided with high-voltage protection.
ADAM-3000
Applications
Motion Control






Industrial on/off control
Contact closure monitoring
Switch status sensing
BCD interfacing
Digital input control
Industrial and lab automation
DO
DI
IDO
IDI
EGND
ECOM
GND
PCOM
Digital output
ICOM
Digital input
Isolated digital output
Isolated digital input
External ground for isolated output eConnectivity
External common for isolated input
Digital ground
Free wheeling common diode
UNO
ADAM-4000
ADAM-5000
ADAM-6000
Isolated Input Circuit Diagram
ADAM-8000
BAS
Isolated Output Circuit Diagram
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-35
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-36
PCI-1752
PCI-1754
PCI-1756
PCI-1752
64-ch Isolated Digital Output Card
64-ch Isolated Digital Input Card
64-ch Isolated Digital I/O Card
PCI-1754
ADAM-3951
PCI-1752


•
•
Features
64 isolated digital input channels
Either +/- voltage input for DI by group
High-voltage isolation on input channels (2500 VDC)
High over-voltage protection (70 VDC)
Wide input range (10 ~ 50 VDC)
Interrupt handling capability
High-density 100-pin SCSI connector
Specifications
General
 I/O Connector Type
 Dimensions (L x H)
 Power Consumption
General
 I/O Connector Type
 Dimensions (L x H)
 Power Consumption
100-pin SCSI-II female
175x100mm (6.9”x3.9”)
Typical: +5 V @ 230 mA
Max.: +5 V @ 500 mA
 Operating Temperature 0~60° C (32 ~ 140° F)
(IEC 68-2-1, 2)
 Storage Temperature -20~70° C (-4 ~ 158° F)
 Relative Humidity
5~95 % (IEC 68-2-3)
non-condensing
Isolated Digital Output
Output Channels
64 (16-ch/group)
Optical Isolation
2,500 VDC
Opto-isolator resp. time 25 µs
Supply Voltage
5 ~ 40 VDC
Sink Current
200 mA max./channel
Ordering Information
 PCI-1752







64-channel Isolated
Digital Output Card,
user's manual and driver
CD-ROM (cable not
included)
100-pin SCSI-II female
175x100mm (6.9”x3.9”)
Typical: +5 V @ 340 mA
Max.: +5 V @ 450 mA
 Operating Temperature 0~60° C (32 ~ 140° F)
(IEC 68-2-1, 2)
 Storage Temperature -20~70° C (-4 ~ 158° F)
 Relative Humidity
5~95 % (IEC 68-2-3)
non-condensing
Isolated Digital Input








ADAM-3951
PCI-1756
Features
64 isolated digital output channels
High-voltage isolation on output channels (2500 VDC)
2000 VDC ESD protection
Wide output range (5 ~ 40 VDC)
High-sink current on isolated output channels (200
mA max./channel)
Output status read-back
Keeps digital output values when hot system reset
Channel-freeze function
High-density 100-pin SCSI connector
Specifications





PCI-1756
PCI-1754
Features





ADAM-3951
Input Channels
64 (16-ch/group)
Interrupt Inputs
4
Optical Isolation
2,500 VDC
Opto-Isolator Resp.
25 µs
Time
Over-Voltage Protection 70 VDC
ESD
2,000 VDC
Input Voltage
VIH (max.)
50 VDC
VIH (min.)
10 VDC
VIL (max.)
3 VDC
Input Current
10 VDC
1.7 mA (typical)
12 VDC
2.1 mA (typical)
24 VDC
4.4 mA (typical)
48 VDC
9.0 mA (typical)
50 VDC
9.4 mA (typical)
 Either +/- voltage input for DI by group
 Output status read-back for output channels
 Keeps digital output values after hot system reset
Specifications
General
 I/O Connector Type
 Dimensions (L x H)
 Power Consumption
100-pin SCSI-II female
175x100mm (6.9”x3.9”)
Typical: +5 V @ 285 mA
Max.: +5 V @ 475 mA
 Operating Temperature 0~60° C (32 ~ 140° F)
(IEC 68-2-1, 2)
 Storage Temperature -20~70° C (-4 ~ 158° F)
 Relative Humidity
5~95 % (IEC 68-2-3)
non-condensing
Isolated Digital Output
 Output Channels
 Optical Isolation
 Opto-Isolator Resp.
Time
 Supply Voltage
 Sink Current
32 (16-ch/group)
2,500 VDC
25 µs
5 ~ 40 VDC
200 mA max./channel
Isolated Digital Input








Input Channels
32 (16-ch/group)
Interrupt Inputs
2 (IDI0, IDI16)
Optical Isolation
2,500 VDC
Opto-Isolator Resp.
25 µs
Time
Over-Voltage Protection 70 VDC
ESD
2,000 VDC
Input Voltage
VIH (max.)
50 VDC
VIH (min.)
10 VDC
VIL (max.)
3 VDC
Input Current
10 VDC
1.7 mA (typical)
12 VDC
2.1 mA (typical)
24 VDC
4.4 mA (typical)
48 VDC
9.0 mA (typical)
50 VDC
9.4 mA (typical)
Ordering Information
Ordering Information
 PCI-1754
 PCI-1756
64-channel Isolated
Digital Input Card
64-channel Isolated
Digital I/O Card
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1752
PCI-1754
PCI-1756
Accessories
 PCL-10250
 PCL-10250-2
 ADAM-3951
 ADAM-3950S
 ADAM-3950D
Applications
100-pin SCSI to two 50-pin SCSI cable, 1m
100-pin SCSI to two 50-pin SCSI cable, 2m
Wiring terminal module with LED indicators for
DIN-rail mounting
50-pin SCSI-II Wiring Terminal
Dual 50-pin SCSI-II Wiring Terminal
Block Diagram (PCI-1756)
•
•
•
•
•
•
•
•
•
•
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Industrial On/Off control
Switch status sensing
BCD interfacing
Digital I/O control
Industrial and lab automation
SMT/PCB machinery
Semi-conductor machinery
PC-based Industrial Machinery
Testing & Measurement
Laboratory & Education
IPPC
TPC
FPM
Feature Details
ATM & AWS
PCI-1752, PCI-1754 and PCI-1756 offer isolated digital input channels and isolated
digital output channels with isolation protection up to 2,500 VDC. This makes them
ideal for industrial applications where high-voltage isolation is required. In addition, all
output channels are able to keep their last values after a hot system reset. Furthermore, DA&C
the PCI-1752 and PCI-1756 provide a channel-freeze function that keeps the current
output status unchanged for each channel during operation.
cPCI
Robust Protection
Pin Assignments
PCI-1752
PCI-1754
PCI-1756
PCI-1752, PCI-1754 and PCI-1756 feature robust isolation protection for applications in
industrial, lab and machinery automation. It can durably withstand voltage up to 2,500
VDC , preventing your host system from any incidental harm. If connected to an external ADAM-3000
input source with surge-protection, PCI-1754 and 1756 can offer up to 2,000 V DC ESD
(Electrostatic Discharge) protection for input channels. If the input voltage rises up to 70
V DC, the input channels of PCI-1754 and PCI-1756 can still manage to work properly Motion Control
for a short period of time.
Wide Input/Output Range
ICOM
PCI-1754 and PCI-1756 have a wide range of input voltages from 10 to 50 V DC, and is
therefore suitable for most industrial applications with 12 V DC, 24 V DC and 48 V DC
input voltage. PCI-1752 and PCI-1756 feature a wide output voltage range from 5 to 40
V DC, suitable for most industrial applications with 12 V DC/24 V DC output voltages. eConnectivity
In the meantime, you can also request specific input/output voltage ranges as products
can be tailored to specifications.
UNO
BoardID™ Switch
PCI-1752, PCI-1754 and PCI-1756 have a built-in BoardID™ DIP switch that helps define
each card’s unique identity when multiple identical PCI cards have been installed in the
ADAM-4000
same computer. The BoardID switch is very useful when you build your system with multiple
identical PCI cards. With the correct BoardID switch settings, you can easily identify and
access each card during hardware configuration and software programming.
ADAM-5000
Channel-Freeze Function
PCI-1752 and PCI-1756 provide a Channel-Freeze function, which can be enabled
either in dry contact or wet contact mode (selected by the on-board jumper). When the ADAM-6000
Channel-Freeze function is enabled, the last status of each digital output channel will be
safely kept for emergency use. Moreover, you can enable this function through software
as it is useful in software simulation and testing program.
ADAM-8000
Reset Protection Fulfills Requirement for Industrial Applications
If the system has undergone a hot reset (i.e. without turning off the system power),
PCI-1752 and PCI-1756 can either retain the output values of each channel or return BAS
to its default configuration as open status, depending on its on-board jumper setting.
This function protects the system from performing wrong operations during unexpected
system resets.
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-37
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-38
PCI-1758U
128-ch Isolated Digital I/O Card
Features
NEW
PCI-1758UDO card










128 isolated digital output channels
High-voltage isolation on output channels (2,500 VDC)
Wide output range (5 ~ 40 VDC)
High-sink current for isolated output channels (90 mA max./Channel)
Current protection for each port
BoardID™ switch
Output status read-back
Digital output value retained after hot system reset
Programmable Power-Up States
Watchdog timer






128 isolated digital input channels
Wide input range (5 ~ 25 VDC)
High ESD protection (2,000 VDC)
Digital Filter function
BoardID™ switch
Interrupt handling capability for each channel (128-ch)
PCI-1758UDI card
PCI-1758UDI
PCI-1758UDO
Specifications
Feature Details
Isolated Digital Input
Interrupt Function (PCI-1758UDI)
Model Name
PCI-1758UDI
Input Channels
128
Interrupt Input
128
Optical Isolation
2,500 VDC
Opto-Isolator Response Time
50 µs
Input Voltage
Input Resistance
PCI-1758UDI provides an interrupt function for every digital input channel. All the isolated
digital input channels are connected to the interrupt circuitry. You can disable/enable the
interrupt functions, select trigger type by setting the Rising Edge Interrupt Registers and
Falling Edge Interrupt Registers of PCI-1758UDI. When the interrupt request signals
occur, software will service these interrupt requests by ISR. The multiple interrupt sources
provide the card with more capability and flexibility.
VIH (max)
25V
Digital Filter Function (PCI-1758UDI)
VIH (min)
5V
VIL (max)
2.5V
The digital filter function is used to eliminate glitches on input data and reduce the
number of changes to examine and process. The filter blocks pulses that are shorter than
the specified timing interval and passes pulses that are twice as long as the specified
interval. Intermediate-length pulses that are longer than half of the interval, but less than
the interval, may or may not pass the filter.
3 kΩ
Isolated Digital Output
Model Name
PCI-1758UDO
Output Channels
128
Optical Isolation
2,500 VDC
Opto-Isolator Response Time
50 µs
Supply Voltage
5-40 V
Sink Current
90 mA max./Channel
Watchdog Timer Function (PCI-1758UDO)
Model Name
PCI-1758UDI
I/O Connector Type
MINI-SCSI HDRA-E100 Female
This feature is used to set critical outputs to safe states in the event of a software failure.
When the watch-dog timer is enabled, the PCI-1758UDO has to receive a “watchdog clear”
software command within the interval time specified for the watchdog timer. If it doesn’t,
this is considered a loss of communication between the application and PCI-1758UDO,
and the outputs go to a user-defined safe state and remain in that state until the watchdog
timer is disabled and new values are written by the software. After the watchdog timer
expires, the PCI-1758UDO will ignore any writes until the watchdog timer is disabled.
You can set the watchdog timer timeout period through the WDT register to specify the
amount of time that must elapse before the watchdog timer expires. The counter on the
watchdog timer is configurable up to (232-1) x 100 ns (approximately seven minutes)
before it expires.
Dimensions
175 x 100 mm (6.9” x 3.9”)
Programmable Power-up Status Function (PCI-1758UDO)
General
Power
Consumption
Temperature
PCI-1758UDO
Typical
+5 V @ 0.3 A
+5 V @ 1.1 A
Max.
+5 V @ 0.6 A
+5 V @ 2.2 A
Operating 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1,2)
Storage -20 ~ 70° C (-4 ~ 158° F)
Relative Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
Ordering Information




PCI-1758UDI
PCI-1758UDO
PCL-101100S-1
ADAM-39100
128-channel Isolated Digital Input Card
128-channel Isolated Digital Output Card
100-pin SCSI Cable, 1m
100-pin SCSI wiring terminal, DIN-rail mounting
User-configurable power-up states are useful for ensuring that the PCI-1758UDO powers
up in a known state. When the system is power-up, all output lines of PCI-1758UDO are
user-configurable for logic high output or logic low output. So the output can be predefined
by users. This function ensures the card’s output state can be defined at any time.
Applications
1. Industrial On/Off control
2. Relay and switch monitoring and controlling
3. Industrial and lab automation
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Block Diagram
Pin Assignments
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
PAB_COMM
PAB_COMM
PB_IDI07
PB_IDI06
PB_IDI05
PB_IDI04
PB_IDI03
PB_IDI02
PB_IDI01
PB_IDI00
PA_IDI07
PA_IDI06
PA_IDI05
PA_IDI04
PA_IDI03
PA_IDI02
PA_IDI01
PA_IDI00
NC
NC
NC
NC
NC
NC
NC
NC
P89_COMM
P89_COMM
P9_IDI07
P9_IDI06
P9_IDI05
P9_IDI04
P9_IDI03
P9_IDI02
P9_IDI01
P9_IDI00
P8_IDI07
P8_IDI06
P8_IDI05
P8_IDI04
P8_IDI03
P8_IDI02
P8_IDI01
P8_IDI00
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
P0_IDI00
P0_IDI01
P0_IDI02
P0_IDI03
P0_IDI04
P0_IDI05
P0_IDI06
P0_IDI07
P1_IDI00
P1_IDI01
P1_IDI02
P1_IDI03
P1_IDI04
P1_IDI05
P1_IDI06
P1_IDI07
P01_COMM
P01_COMM
NC
NC
NC
NC
NC
NC
NC
NC
P2_IDI00
P2_IDI01
P2_IDI02
P2_IDI03
P2_IDI04
P2_IDI05
P2_IDI06
P2_IDI07
P3_IDI00
P3_IDI01
P3_IDI02
P3_IDI03
P3_IDI04
P3_IDI05
P3_IDI06
P3_IDI07
P23_COMM
P23_COMM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
PCI-1758UDI Block Diagram
NC
NC
NC
NC
NC
NC
P4_IDI00
P4_IDI01
P4_IDI02
P4_IDI03
P4_IDI04
P4_IDI05
P4_IDI06
P4_IDI07
P5_IDI00
P5_IDI01
P5_IDI02
P5_IDI03
P5_IDI04
P5_IDI05
P5_IDI06
P5_IDI07
P45_COMM
P45_COMM
NC
NC
NC
NC
NC
NC
NC
NC
P6_IDI00
P6_IDI01
P6_IDI02
P6_IDI03
P6_IDI04
P6_IDI05
P6_IDI06
P6_IDI07
P7_IDI00
P7_IDI01
P7_IDI02
P7_IDI03
P7_IDI04
P7_IDI05
P7_IDI06
P7_IDI07
P67_COMM
P67_COMM
IPPC
PLX
PCI9030
Local Bus
Digital IN
Control
Unit(FPGA)
OSC 10M
Flash
PCI-1758UDO Block Diagram
ADAM-3000
Power up
and
Watchdog
Digital
output data
storage
unit
PAB_COMP
PAB_COMP
PB_IDO07
PB_IDO06
PB_IDO05
PB_IDO04
PB_IDO03
PB_IDO02
PB_IDO01
PB_IDO00
PA_IDO07
PA_IDO06
PA_IDO05
PA_IDO04
PA_IDO03
PA_IDO02
PA_IDO01
PA_IDO00
PAB_COMM
PAB_COMM
PAB_COMM
PAB_COMM
PAB_COMM
PAB_COMM
NC
NC
P89_COMP
P89_COMP
P9_IDO07
P9_IDO06
P9_IDO05
P9_IDO04
P9_IDO03
P9_IDO02
P9_IDO01
P9_IDO00
P8_IDO07
P8_IDO06
P8_IDO05
P8_IDO04
P8_IDO03
P8_IDO02
P8_IDO01
P8_IDO00
P89_COMM
P89_COMM
P89_COMM
P89_COMM
P89_COMM
P89_COMM
P01_COMM
P01_COMM
P01_COMM
P01_COMM
P01_COMM
P01_COMM
P0_IDO00
P0_IDO01
P0_IDO02
P0_IDO03
P0_IDO04
P0_IDO05
P0_IDO06
P0_IDO07
P1_IDO00
P1_IDO01
P1_IDO02
P1_IDO03
P1_IDO04
P1_IDO05
P1_IDO06
P1_IDO07
P01_COMP
P01_COMP
NC
NC
P23_COMM
P23_COMM
P23_COMM
P23_COMM
P23_COMM
P23_COMM
P2_IDO00
P2_IDO01
P2_IDO02
P2_IDO03
P2_IDO04
P2_IDO05
P2_IDO06
P2_IDO07
P3_IDO00
P3_IDO01
P3_IDO02
P3_IDO03
P3_IDO04
P3_IDO05
P3_IDO06
P3_IDO07
P23_COMP
P23_COMP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
P45_COMM
P45_COMM
P45_COMM
P45_COMM
P45_COMM
P45_COMM
P4_IDO00
P4_IDO01
P4_IDO02
P4_IDO03
P4_IDO04
P4_IDO05
P4_IDO06
P4_IDO07
P5_IDO00
P5_IDO01
P5_IDO02
P5_IDO03
P5_IDO04
P5_IDO05
P5_IDO06
P5_IDO07
P45_COMP
P45_COMP
NC
NC
P67_COMM
P67_COMM
P67_COMM
P67_COMM
P67_COMM
P67_COMM
P6_IDO00
P6_IDO01
P6_IDO02
P6_IDO03
P6_IDO04
P6_IDO05
P6_IDO06
P6_IDO07
P7_IDO00
P7_IDO01
P7_IDO02
P7_IDO03
P7_IDO04
P7_IDO05
P7_IDO06
P7_IDO07
P67_COMP
P67_COMP
Local Bus
Digital Out
Control
Unit(FPGA)
PCI BUS
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
PLX
PCI9030
CNA
Motion Control
Connector: HDRA
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
ICOM
eConnectivity
UNO
OSC 10M
FPGA
Configurati
on Control
Unit(CPLD)
Flash
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
I/O Connector Pin Assignment for PCI-1758UDO
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
ATM & AWS
cPCI
Output Driver
PEF_COMP
PEF_COMP
PF_IDO07
PF_IDO06
PF_IDO05
PF_IDO04
PF_IDO03
PF_IDO02
PF_IDO01
PF_IDO00
PE_IDO07
PE_IDO06
PE_IDO05
PE_IDO04
PE_IDO03
PE_IDO02
PE_IDO01
PE_IDO00
PEF_COMM
PEF_COMM
PEF_COMM
PEF_COMM
PEF_COMM
PEF_COMM
NC
NC
PCD_COMP
PCD_COMP
PD_IDO07
PD_IDO06
PD_IDO05
PD_IDO04
PD_IDO03
PD_IDO02
PD_IDO01
PD_IDO00
PC_IDO07
PC_IDO06
PC_IDO05
PC_IDO04
PC_IDO03
PC_IDO02
PC_IDO01
PC_IDO00
PCD_COMM
PCD_COMM
PCD_COMM
PCD_COMM
PCD_COMM
PCD_COMM
FPM
DA&C
FPGA
Configurati
on Control
Unit(CPLD)
I/O Connector Pin Assignment for PCI-1758UDI
CNB
TPC
Photo Coupler
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Connector: HDRA
PEF_COMM
PEF_COMM
PF_IDI07
PF_IDI06
PF_IDI05
PF_IDI04
PF_IDI03
PF_IDI02
PF_IDI01
PF_IDI00
PE_IDI07
PE_IDI06
PE_IDI05
PE_IDI04
PE_IDI03
PE_IDI02
PE_IDI01
PE_IDI00
NC
NC
NC
NC
NC
NC
NC
NC
PCD_COMM
PCD_COMM
PD_IDI07
PD_IDI06
PD_IDI05
PD_IDI04
PD_IDI03
PD_IDI02
PD_IDI01
PD_IDI00
PC_IDI07
PC_IDI06
PC_IDI05
PC_IDI04
PC_IDI03
PC_IDI02
PC_IDI01
PC_IDI00
NC
NC
NC
NC
NC
NC
CNA
PCI BUS
CNB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Photo Coupler
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1758U
Last updated : January 2005
6-39
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-40
PCI-1757UP
24-channel Digital Input/Output
Low Profile Universal PCI Card
Features
 Low profile PCI card
 Universal PCI card, fits 3.3 V and 5 V PCI slot
 24 TTL level digital I/O lines
 Emulates mode 0 of 8255 PPI
 Buffered circuits provide higher driving capability
 Output status read-back
 I/O configurable by software or on board DIP switch
 Keeps port I/O settings and digital output states after hot reset
 BoardID™ switch
 High density D-SUB 25-pin connector
Introduction
The PCI-1757UP is a 24-bit DI/O low profile PCI card that meets the PCI standard REV.2.2 (universal PCI expansion card). The card also works with 3.3 V and 5 V PCI slots, and
provides you with 24 bits of parallel digital input/output, that emulates mode 0 of the 8255 PPI chip. However, the buffered circuits offer a higher driving capability than the 8255.
Specifications
Ordering Information
Digital Input
 PCI-1757UP
 ADAM-3925
 Logic High Voltage
 Logic Low Voltage
 High Level
Input Current
 Low Level
Input Current
2.0 to 5.25 V
0.0 to 0.80 V
20 mA
-0.2 mA
Digital Output
 Logic High Voltage
 Logic Low Voltage
 High Level
Input Current
 Low Level
Input Current
 Driving Capability
2.4 V minimum
0.4 V maximum
15 mA maximum (source)
24 mA maximum (sink)
15 LS TTL
Interrupt Source
 PC0, PC4
General






Connector
Power Consumption
Operating Temperature
Storage Temperature
Humidity
Dimensions
One D-SUB 25-pin female connector
5 V @ 140 mA (Typical)
0 ~ 70° C (32 ~ 158° F)
-20 ~ 80° C(-4 ~ 176° F)
5 ~ 95% non-condensing
119.91 x 64.41 mm (4.721" x 2.536") Low profile PCI
MD1 card size
Plug-in DA&C Cards
24-channel Digital Input/Output Card
DB-25 wiring terminal for DIN-rail mounting
Pin Assignments
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1736UP
32-channel Isolated Digital
Input/Output Card
Features
NEW
 32 isolated DI/O channels (16 inputs and 16 outputs)
 High output driving capacity
 High-voltage isolation on I/O channels (2500 VDC)
 Interrupt handling capability
 D-type connector for isolated input and output channels
 Keep digital output values when hot system reset
 Wide input range (5 ~ 50 VDC)
 Surge protection
 Universal PCI Bus
 Low profile card
 BoardID™ switch
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
IPPC
TPC
FPM
ATM & AWS
DA&C
Introduction
PCI-1736UP offer isolated digital input channels as well as isolated digital output channels with isolation protection up to 2,500 VDC, which makes it ideal for industrial applications
where high-voltage isolation is required.
cPCI
In addition, all output channels provide high-voltage protection. The low profile PCI form factor and universal PCI connector (V2.2 compliant) meet requirements for size and power ADAM-3000
consumption.
Specifications
Pin Assignments
 Bus interface










PCI bus spec. 2.2 compliant
PCI universal card (both 3.3V and 5V signaling)
IRQ
All ports use the same IRQ assigned by PCI Plug-andPlay
I/O Channels
16 Isolated DI and 16 Isolated DO
Isolation Protection
2500 VDC
Input Voltage Range
5-50 VDC
Output Voltage Range Open collector 5-40 VDC
Connector
DB-44 female connector
Dimensions
Low profile PCI MD1 (119.91 x 64.41 mm)
Operating Temperature 0 ~ 60 °C (32 ~ 140° F)
Storage Temperature -25 ~ 85 °C (-4 ~ 185° F)
Operating Humidity
5 ~ 95% Relative Humidity, non-condensing
Ordering Information
 PCI-1736UP
 PCL-10144-1
 ADAM-3944
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
32-channel isolated digital input/output card
DB 44-pin cable, 1m
DB-44 Wiring Terminal for DIN-rail mounting
ADAM-6000
Applications






Motion Control
ADAM-8000
Industrial on/off control
Contact closure monitoring
Switch status sensing
BCD interfacing
Digital input control
Industrial and lab automation
BAS
Online Download www.advantech.com/products
6-41
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-42
PCI-1763UP
8-ch Relay and 8-ch Isolated DI card
Features













8 relay output channels and 8 isolated digital input channels
LED indicators to show activated relays
8 Form C type relay output channels
Output status read-back
Retained relay output values when hot system reset
High-voltage isolation on input channels (3,750 VDC)
High ESD protection (2,000 VDC)
High over-voltage protection (70 VDC)
Wide input range (10 ~ 50 VDC)
Interrupt handling capability
Support Universal PCI Bus
Low Profile PCI card
BoardID™ switch
Introduction
PCI-1763UP relay actuator and isolated D/I card is an add-on card for the PCI bus. It provides 8 optically-isolated digital inputs with isolation protection of 2500 VDC for collecting digital
inputs in noisy environments, and 8 relay actuators for serving as on/off control devices or small power switches. For easy monitoring, each relay is equipped with one red LED
to show its on/off status. The PCI-1761’s eight optically-isolated digital input channels are ideal for digital input in noisy environments or with floating potentials. The low profile PCI
form factor and universal PCI connector (V2.2 compliant), meet requirements for size and reduced power consumption.
Pin Assignments
Specifications
Isolated Digital Input
NO0
COM0
NO1
COM1
NO2
COM2
NO3
COM3
NO4
COM4
NO5
COM5
NO6
COM6
NO7
COM7
 Channels
8
 Optical Isolation
3,750 VDC
 Opto-isolator
25 µs
Response Time
 Over-Voltage Protection 70 VDC
 Input Voltage
5 ~ 50 VDC
 Input Current
3.16 mA @ 10 VDC
17.3 mA @ 50 VDC
Relay Output










Channels
Relay Type
Rating (resistive)
Max. Switching Power
Insulation Resistance
Operate Time
Release Time
I/O Connector Type
Dimensions
Power Consumption
8
DPDT (8 Form C)
0.25 A @ 240 VAC or 1 A @ 30 VDC
62.5 AV, 60 W
1,000 MΩ min. (at 500 VDC)
5 ms max.
4 ms max.
DB44 female
119.91 x 64.41 mm
+5V @ 107.5 mA (typical)
+5V @ 301.3 mA (max.)
DI0H
DI1L
DI2L
DI2H
DI3H
DI4L
DI5L
DI5H
DI6H
DI7L
Environment
 Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1,2)
 Storage Temperature -20 ~ 70° C (-4 ~158° F)
 Relative Humidity
5 ~ 95 % RH non-condensing (refer to IEC 68-2-3)
Plug-in DA&C Cards
CN1
30
15
29
14
28
13
27
12
26
11
25
10
24
9
23
8
22
7
21
6
20
5
19
4
18
3
17
2
16
1
44
NC0
43
NC1
42
NC2
41
NC3
40
NC4
39
NC5
38
NC6
37
NC7
36
DI0L
35
DI1H
34
DI3L
33
DI4H
32
DI6L
31
DI7H
Ordering Information
 PCI-1763UP
 PCL-10144-1
 ADAM-3944
8-ch Relay and 8-ch Isolated DI card
DB 44-pin cable, 1m
DB-44 Wiring Terminal for DIN-rail mounting
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1750
32-ch Isolated Digital I/O
and Counter Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 16 isolated DI and 16 isolated DO channels
 High voltage isolation on all isolated channels (2,500 VDC)
 High sink current on isolated output channels (200 mA/channel)
 Supports dry contact or 5 ~ 50 VDC isolated inputs
 Interrupt handling
IPPC
TPC
 Timer/counter interrupt capability
FPM
ATM & AWS
DA&C
Introduction
cPCI
PCI-1750 offers 16 isolated digital input channels, 16 isolated digital output channels, and one isolated counter/timer for the PCI bus. With isolation protection of 2,500 VDC, and
dry contact support, PCI-1750 is ideal for industrial applications where high-voltage protection is required. Each I/O channel of the PCI-1750 corresponds to a bit in a PC I/O port.
This makes PCI-1750 very easy to program. This card also offers a counter or timer interrupt and two digital input interrupt lines to a PC. So you can then easily do configurations
by software.
ADAM-3000
Plug & Play
PCI-1750 uses a PCI controller to interface the card to the PCI bus. The controller fully implements PCI bus specification Rev 2.1. All bus relative configurations, such as base address
Motion Control
and interrupt assignment, are automatically controlled by the software. No jumper or DIP switch is required for user configuration.
On-board Programmable Counter/Timer
PCI-1750 provides a programmable counter/timer for generating periodic interrupts to the host computer. The counter/timer chip is an 82C54, which includes three 16-bit counters ICOM
based on a 10 MHz clock. One counter is used to count events coming from the isolated input channel. The other two are cascaded together to make a 32-bit timer.
Specifications
Ordering Information
Digital Input
 PCI-1750




16 Optically-isolated Inputs
Input Range
5 ~ 50 VDC or dry contact
Isolation Voltage
2,500 VDC
Throughput
10 kHz
Digital Output





16 Optically-isolated Outputs
Output Range
Open collector 5 ~ 40 VDC
Sink Current
200 mA max. per channel
Isolation Voltage
2,500 VDC
Throughput
10 kHz
Programmable Counter/Timer
 One 32-bit timer
 One 16-bit optically-isolated Counter
- Shares pin with isolated input 15
- Throughput: 1 MHz max.
- Isolation voltage: 2,500 VDC




PCL-10137-1
PCL-10137-2
PCL-10137-3
ADAM-3937
32-channel Isolated DIO and Counter Card, user’s manual
and driver CD-ROM. (cable not included)
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
37-pin D-type cable wiring terminal for DIN-rail mounting
Applications






Industrial on/off control
Contact closure monitoring
Switch status sensing
BCD interfacing
Digital I/O control
Industrial and lab automation
Pin Assignments
Interrupt Source
Power Consumption
Operating Temperature
Storage Temperature
Operating Humidity
Connectors
 Dimensions (L x H)
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
General






eConnectivity
Isolated input 0, 8, counter and timer
5 V @ 850 mA (typical), 5 V @ 1.0 A (max.)
0 ~ 70° C (32 ~ 158° F)
-20 ~ 80° C (-4 ~ 176° F)
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
One 37-pin D-type female connector
One 2-pin terminal block for extended ground
175 x 100 mm (6.9" x 3.9")
BAS
Online Download www.advantech.com/products
6-43
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-44
PCI-1761
8-ch Relay Actuator and
8-ch Isolated Digital Input Card
Features
 8 relay output channels and 8 isolated digital input channels
 LED indicators to show activated relays
 4 Form C and 4 Form A type relay output channels
 Output status read-back
 Retained relay output values when hot system reset
 High-voltage isolation on input channels (3,750 VDC)
 High ESD protection (2,000 VDC)
 High over-voltage protection (70 VDC)
 Wide input range (10 ~ 50 VDC)
 Interrupt handling capability
 BoardID™ switch
Introduction
The PCI-1761 relay actuator and isolated D/I card is an add-on card for the PCI bus. It provides 8 optically-isolated digital inputs with isolation protection of 3,750 VDC for collecting
digital inputs in noisy environments and 8 relay actuators for serving as on/off control devices or small power switches. For easy monitoring, each relay is equipped with one red LED
to show its on/off status. The PCI-1761’s eight optically-isolated digital input channels are ideal for digital input in noisy environments or with floating potentials.
Rugged Protection
The PCI-1761 digital input channels feature a rugged isolation protection for industrial, lab and machinery automation applications. It durably withstands voltage up to 3,750 VDC,
protecting your host system from any incidental harms. If connected to an external input source with surge-protection, the PCI-1761 can offer up to a maximum of 2,000 VDC ESD
(Electrostatic Discharge) protection. Even with an input voltage rising up to 70 VDC, the PCI-1761 can still manage to work properly, albeit for only a short period of time.
Reset Protection Fulfills Requirement for Industrial Applications
When the system has undergone a hot reset (i.e. without turning off the system power), the PCI-1761 can either retain output values of each channel, or return to its default configuration
as open status, depending on its onboard jumper setting. This function protects the system from unwanted operations during unexpected system resets.
Specifications
General
Isolated Digital Input
 Channels
8
 Optical Isolation
3,750 VDC
 Opto-isolator
25 µs
Response Time
 Over-Voltage Protection 70 VDC
 Input Voltage
10 ~ 50 VDC
 Input Current
1.6 mA @ 10 VDC
8.9 mA @ 50 VDC
Relay Output








Channels
Relay Type
Rating (resistive)
Max. Switching Power
Max. Switching Load
Insulation Resistance
Operate Time
Release Time
8
SPDT (4 Form C and 4 Form A)
3 A @ 250 VAC or 3 A @ 24 VDC
750 AV, 72 W
10 mA @ 5 VDC
1,000 MΩ min. (at 500 VDC)
15 ms max.
5 ms max.
Plug-in DA&C Cards
 Connector
 Dimensions (L x H)
 Power Consumption
One 37-pin D-type connector
175 x 100 mm (6.9" x 3.9")
+5 V @ 220 mA (typical)
+5 V @ 750 mA (max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Operating Humidity
5 ~ 95 % RH non-condensing (refer to IEC 68-2-3)
Ordering Information






PCI-1761
PCL-10137-1
PCL-10137-2
PCL-10137-3
ADAM-3937
PCLD-880
8-ch Relay Actuator and 8-ch Isolated D/I Card
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
DB37 Wiring Terminal for Din-rail Mounting
Universal screw terminal board
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1760
PCI-1760U
8-ch Relay Actuator and
Isolated D/I Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Universal PCI card, for 3.3 V and 5 V PCI slot
 8 opto-isolated digital input channels
 8 relay actuator output channels
 2 opto-isolated PWM outputs
 LED indicators to show activated relays
 Jumper selectable dry contact/wet contact input signals
 Up event counters for DI
 Programmable digital filter function for DI
 Pattern match interrupt function for DI
 "Change of State" interrupt function for DI
 Universal PCI and BoardID switch (PCI-1760U only)
IPPC
TPC
FPM
ATM & AWS
DA&C
Introduction
The PCI-1760U relay actuator and isolated D/I card is a PC add-on card for the PCI bus. It meets the PCI standard Rev. 2.2 (Universal PCI expansion card), and works with both 3.3
V and 5 V PCI slots. It provides 8 opto-isolated digital inputs with isolation protection of 2,500 VDC for collecting digital inputs in noisy environments, 8 relay actuators that can be
used as a on/off control devices or small power switches, and 2 isolated PWM (Pulse Width Modulation) outputs for custom applications.
For easy monitoring, each relay is equipped with one red LED to show its on/off status. Each isolated input supports both dry contact and wet contact so that it can easily interface
with other devices when no voltage is present in the external circuit.
Specifications
Isolated PWM output
Isolated Digital Input
 Channels
 Opto-isolator
 Input Voltage
 Input Resistance
 Isolation Voltage
 Digital Filter
 16-bit UP Counter
8 (Sink)
PC354
5 ~ 12 VDC
High: > 4.5 V
Low: < 1.0 V
Uncertain: 1.0 V ≥ Vin ≥ 4.5 V
1 kΩ 1/4 W
2,500 VDC
Minimum effective high input period ≥ [(2 ~ 65535) x
5 ms] + 5 ms
Minimum effective low input period ≥ [(2 ~ 65535) x
5 ms] + 5 ms
Maximum effective input frequency: 500 Hz
Minimum High period ≥ 1 ms
Minimum Low period ≥ 1 ms
Relay Output
 Channels
 Relay Type
 Output Type
 Rating Contact Load
 Contact Resistance
 Dielectric Strength
 Life Expectancy
 Operating Time
 Releasing Time
8
Single-pole double-throw (SPDT, Form C)
CH0 and CH1: NC and NO outputs
CH2 ~ CH7: NC or NO outputs (selected by jumper)
120 VDC @ 0.5 A or 30 VDC @ 1 A
Less than 100 m Ω initially
Coil to contacts (deenergized): 1,500 VRMS (1 minute)
Between open contacts (deenergized & energized):
1,000 VRMS (1 minute)
200,000 operations @ 0.5 A 120 VAC
500,000 operations @ 1.0 A 30 VDC
5 ms max.
5 ms max.
 Channels
 Isolation Voltage
 Scaling Resolution
 Output Level
Power Consumption
Operating Temperature
Storage Temperature
Operating Humidity
+5 V @ 450 mA (typical), 850 mA (max.)
0 ~ 60° C (32 ~ 140° F) (IEC 68 - 2 - 1, 2)
-20 ~ 70° C (-4 ~ 158° F)
5 ~ 95 % RH non-condensing (IEC 68-2-3)
Physical
 Connector
 Dimensions (L x H)
One 37-pin D-type connector
175 x 100 mm (6.9" x 3.9")
Ordering Information
 PCI-1760U





PCI-1760
PCL-10137-1
PCL-10137-2
PCL-10137-3
ADAM-3937
ADAM-3000
Motion Control
2
2,500 VDC
16 bits (100 ms for each step)
High period = [(1 ~ 65535) x 100 ms ] + 50 ms (max.)
Low period = [(1 ~ 65535) x 100 ms ] + 50 ms (max.)
High: (5 ±0.5) V
Low: < 0.8 V
General




cPCI
Relay Actuator and Isolated D/I Card, user’s manual
and driver CD-ROM (cable not included)
8-ch Relay Actuator and Isolated D/I card
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
DB37 wiring terminal for DIN-rail mounting
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Applications




Digital signal and contact status monitoring
Industrial On/Off control
Signal switching
External relay driving
Online Download www.advantech.com/products
6-45
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-46
PCI-1762
16-ch Isolated Digital Input
and 16-ch Relay Output Card
Features
 16 relay output channels and 16 isolated digital input channels
 LED indicators to show activated relays
 Jumper selectable Form A/Form B-type relay output channel
 Output status read-back
 Retain relay output values when hot system reset
 High-voltage isolation on input channels (2,500 VDC)
 High ESD protection (2,000 VDC)
 High over-voltage protection (70 VDC)
 Wide input range (10 ~ 50 VDC)
 Interrupt handling capability
 High-density DB-62 connector
 BoardID™ switch
Introduction
The PCI-1762 relay actuator and isolated D/I card is a PC add-on card for the PCI bus. It provides 16 opto-isolated digital inputs with isolation protection of 2,500 VDC for collecting
digital inputs in noisy environments, 16 relay actuators for serving as on/off control devices or small power switches. For easy monitoring, each relay is equipped with one red LED
to show its on/off status. The PCI-1762’s sixteen optically-isolated digital input channels are ideal for digital input in noisy environments or with floating potentials.
Specifications
Isolated Digital Input
 Input Channels
16
 Optical Isolation
2,500 VDC
 Opto-Isolator
25 µs
Response Time
 Over-Voltage Protection 70 VDC
 Input Voltage
VIH (max.)
50 VDC
VIH (min.)
10 VDC
VIL (max.)
3 VDC
 VIL (max.)
10 VDC 1.6 mA (typical)
12 VDC 1.9 mA (typical)
24 VDC 4.1 mA (typical)
48 VDC 8.5 mA (typical)
50 VDC 8.9 mA (typical)
Relay Output












Output Channels
16
Relay Type
SPDT (Form A or Form B, Jumper selectable)
Rating (resistive)
0.5 A @ 125 VAC or 1 A @ 30 VDC
Max. Switching Power 62.5 AV, 30 W
Max. Switching Voltage 250 VAC, 220 VDC
Max. Switching Current 2 A
Minimum Switching
10 µA @ 10 m VDC
Load
Breakdown Voltage
1,500 VAC for 1 min. (between coil and contacts)
Operate Time
6 ms max.
Release Time
4 ms max.
Insulation Resistance 1,000 MΩ min. (at 500 VDC)
Life Expectancy
2 x 105 ops. min. (0.5 A @ 125 VAC) , 5 x 105 ops.
min. (1 A @ 30 VDC)
General
 I/O Connector Type
 Dimensions
 Power Consumption
DB62 D-type female connector
175 x 100 mm (69” x 3.9”)
+5V @ 250 mA (typical)
+5V @ 620 mA (max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68-2-1,2)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Relative Humidity
5 - 95 % non-condensing (IEC 68-2-3)
 Certification
CE Class A
Ordering Information
 PCI-1762




PCL-10162-1
PCL-10162-3
PCL-10162-5
ADAM-3962
16-ch Isolated Digital Input and 16-ch Relay Output
Card
PCL-10162-1 DB-62 cable assembly, 1m
PCL-10162-3 DB-62 cable assembly, 3m
PCL-10162-5 DB-62 cable assembly, 5m
DB62 Wiring Terminal for Din-rail Mounting
Applications
 Industrial On/Off control
 Switch status sensing
 Digital I/O control
 Industrial and lab automation
 SMT/PCB machinery
 Semi-conductor machinery
 PC-based Industrial Machinery
 Testing & Measurement
 Laboratory & Education
 External relay driving
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1780
8-ch Counter/Timer Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 8 independent 16-bit counters
 8 programmable clock source
IPPC
 8 digital TTL outputs and 8 digital TTL inputs
 Up to 20 MHz input frequency
 Multiple counter clock source selectable
TPC
 Counter output programmable
 Counter gate function
 Flexible interrupt source select
FPM
 BoardID™ switch
ATM & AWS
DA&C
Introduction
PCI-1780 is a general purpose multiple channel counter/timer card for the PCI bus. It targets the AM9513 to implement the counter/timer function by CPLD. Plus, it provides eight
16-bit counter channels and 8 digital outputs and 8 digital inputs. Advantech has designed powerful counter functions to for a broad range of industrial and laboratory applications.
cPCI
ADAM-3000
Flexible Counter Modes
The PCI-1780 features up to 12 programmable counter modes, to provide one shot output, PWM output, periodic interrupt output, time-delay output, and to measure the frequency
and the pulse width. The PCI-1780 is an ideal solution for various counter/timer applications.
Motion Control
Special Shielded Cable for Noise Reduction
The PCL-10168 shielded cable is specially designed for the PCI-1780 for reducing noise. Its wires are all twisted pairs, and the input signals and output signals are separately shielded,
providing minimal cross talk between signals and the best protection against EMI/EMC problems.
ICOM
BoardID™ Switch
PCI-1780 has a built-in BoardID™ DIP switch that helps define each card’s unique identity when multiple identical PCI cards have been installed in the same computer. The BoardID
eConnectivity
switch is very useful when you build your system with multiple identical PCI cards. With the correct BoardID switch settings, you can easily identify and access each card during
hardware configuration and software programming.
Plug & Play Function
UNO
PCI-1780 is a Plug & Play device which fully complies with PCI Specification Rev 2.2. During card installation, there is no need to set jumpers or DIP switches. Instead, all
Specifications
Programmable Counter
 Channels
 Resolution
 Programmable
Clock Source
 Programmable
Counter Modes
 Max. Frequency
 Interrupt Source
8 (independent)
16-bit
8 independent
12
20 MHz
8 counter outputs
Digital Input/Output
 Input Channels
 Input Voltage
 Interrupt Source
 Output Channels
 Output Voltage
ADAM-4000
General
8
Low: 0.8 V max.
High: 2.4 V min.
Channel 0
8
Low 0.5 V max. @ 24 mA (sink)
High 2.4 V min. @ -15 mA (source)
 I/O Connector Type
 Dimensions
 Power Consumption
68-pin SCSI-II female
175 x 100 mm (6.9” x 3.9”)
Typical: +5 V @ 900 mA
Max.: +5 V @ 1.2 A
 Operating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68-2-1, 2)
 Storage Temperature -20 ~ 70 °C (-4 ~ 158 °F)
 Relative Humidity
5 ~ 95 % RH non-condensing (IEC 68-2-3)
 Certifications
CE certified
 PWM Range
0.0005 ~ 60 Sec.
Ordering Information
 PCI-1780
 PCL-10168
 ADAM-3968
ADAM-6000
ADAM-8000
BAS
8-channel Counter/Timer Card
68-pin SCSI-II cable with male connectors on both ends
and special shielding for noise reduction, 1 and 2 m
68-pin SCSI-II Wiring Terminal Board for DIN-rail
mounting
Online Download www.advantech.com/products
All product specifications are subject to change without notice
ADAM-5000
Last updated : January 2005
6-47
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-48
PCL-711
Analog and Digital
I/O Card
Features
 Eight single-ended analog inputs
 Programmable A/D input range
 A/D, D/A with pacer
 One analog output
 12-bit A/D and D/A resolution
 16 digital inputs
 16 digital outputs
 Includes versatile drivers in popular programming languages plus calibration,
demo and example programs
 Screw-terminal board and cable included
PCL-711B
PCL-10120-1
PCLD-7115
Introduction
PCL-711 is a fully-integrated package that offers four of the most popular I/O functions for PC/AT and compatible systems: A/D conversion, D/A conversion, digital input and digital
output.
The inexpensive PCL-711 is ideal for entry level applications. The features of this half-sized card include: eight 12-bit analog inputs, one 12-bit analog output, 16 digital inputs and
16 digital outputs. In addition, it comes with a 20-point screw-terminal board and a flat cable connector.
PCL-711 performs a variety of I/O jobs, and features solid software support and a large selection of available daughterboards and accessories. It is an ideal and affordable performer
for OEMs, schools and hobbyists who require a combination of analog and digital I/O.
Specifications
Analog Input
Channels
8 single-ended
A/D Converter
12 bit, 25 µs conversion time
Input Range (V)
±5, ±2.5, ±1.25, ±0.625, ±0.3125
Trigger Mode
Software, pacer or external trigger
Data Transfer
Program control, interrupt (IRQs 2 ~ 7)
Accuracy
±2 LSB
Common Mode Rejection
60 dB typical
 Input Impedance
>10 MΩ
 Input Overvoltage
±30 VDC max.














General
 Power Consumption
 PCL-711S
16, TTL level
16
0.5 V max. @ 8 mA (sink)
2.4 V min. @ 0.4 mA (source)
+5 V @ 500 mA typical, 1.0 A max.
+12 V @ 50 mA typical, 100 mA max.
-12 V @ 14 mA typical, 20 mA max.
0 ~ 50° C (32 ~ 122° F)
-20 ~ 65° C (-4 ~ 149° F)
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
16 consecutive I/O ports per card
One 20-pin flat cable connector for A/D and D/A
One 20-pin flat cable connector for digital input
One 20-pin flat cable connector for digital output
155 x 100 mm (6.1" x 3.9")
Ordering Information
 PCL-10120-1
 PCL-10120-2
Digital Output
 Channels
 Logic level 0
 Logic level 1
 Dimensions (L x H)
One 12-bit double-buffered channel
0 ~ 5 V or 0 ~ 10 V
30 µs
Digital Input
 Channels
Operating Temperature
Storage Temperature
Operating Humidity
I/O Ports
Connectors
 PCL-711B
Analog Output
 Channels
 D/A Range
 Settling Time





PCL-711B card, user’s manual, driver CD-ROM,
PCLD-7115 and 1 m 20-pin flat cable (PCL-10120-1)
PCL-711B card only (PCLD-7115, 1 m 20-pin cable,
user manual and driver CD-ROM NOT included).
20-pin flat cable, 1m
20-pin flat cable, 2m
Applications
DC voltage measurement
Transducer/sensor interfacing
Process control
Contact closure monitoring
Digital signal and BCD interfacing
Industrial On/Off control
Multiplexer and relay control
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCL-812PG
MultiLab Analog and
Digital I/O Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 16 single-ended 12-bit analog input channels
 Two 12-bit analog output channels
IPPC
 Programmable sampling rate of up to 30 kHz
 A/D with DMA or interrupt
 16 digital input channels
TPC
 16 digital output channels
 Programmable counter/timer
 Programmable A/D ranges (gains)
FPM
 Includes C/C++, Pascal and BASIC drivers as well as calibration, demo and
example programs
 Comprehensive application software support
ATM & AWS
DA&C
Introduction
PCL-812PG is a multifunction analog and digital I/O card that features the five most desired measurement and control functions for PC/AT and compatible systems: A/D conversion,
D/A conversion, digital input, digital output and counter/timer. This half-size card neatly packages 16 12-bit analog input channels, two 12-bit analog output channels, 16 digital
input channels, 16 digital output channels and a programmable counter/timer.
In addition to all the features listed above, PCL-812PG offers the convenience of programmable analog input ranges, where the analog input range can be switched by software
commands instead of DIP switches. PCL-812PG also delivers convenience and maximum resolution for applications that need different gains for different channels or different gains
for different stages of a process.
Comprehensive software support, numerous I/O options and a wide range of available daughterboards make the PCL-812PG ideal for industrial applications that require a combination
of analog and digital I/O.
Specifications
Analog Input
• Channels
16 single-ended
• A/D Converter
12-bit, 25 µs conversion time
• Input Range (V, software programmable)
±10, ±5, ±2.5, ±1.25, ±0.625, ±0.3125
Software, pacer or external trigger
• Trigger Mode
• Data Transfer
Program controlled, interrupt 2 ~ 7, 9 ~ 12, 14, 15 or
DMA (Channel 1 or 3) for single channel scan
0.01% of reading ±1 LSB
• Accuracy
60 dB typical
• Common Mode
Rejection
• Input Impedance
>10 MΩ
Continuous ±30 VDC max.
• Overvoltage
Analog Output
• Channels
• D/A Range (in V)
•
•
•
•
Settling Time
Throughput
Output Current
Linearity
Two double-buffered 12-bit channels
0 ~ 5, 0 ~ 10 w/internal reference; ±10 V max. with
external AC or DC reference (accuracy for output above
±9 V may vary depending on power supply used)
30 µs
30 kS/s max.
±5 mA max.
±½ bit
Digital Input
• Channels
16, TTL level
16, TTL compatible
8.0 mA @ 0.5 V (sink);
0.4 mA @ 2.4 V (source)
32-bit timer with a 20 MHz time base
500 kHz ~ 0.00046 Hz (one sample every 36 minutes)
One 16-bit counter with a 2 MHz time base
General
+5 V @ 500 mA typical, 1.0 A max.
+12 V @ 50 mA typical, 100 mA max.
• Operating Temperature 0 ~ 50° C (32 ~ 122° F)
• Storage Temperature -20 ~ 65° C (-4 ~ 149° F)
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
• Operating Humidity
• I/O Ports
16 consecutive bytes
• Connectors
Two 20-pin flat cable connectors
• Dimensions (L x H)
185 x 100 mm (7.3" x 3.9")
PCL-10120-1
PCL-10120-2
PCLD-780
PCLD-8115
MultiLab Analog and Digital I/O Card, user’s manual
and driver CD-ROM. (cable not included)
20-pin flat cable, 1m
20-pin flat cable, 2m
Screw terminal board
Industrial wiring terminal board with CJC circuit
Online Download www.advantech.com/products
All product specifications are subject to change without notice
ADAM-5000
ADAM-6000
ADAM-8000
Ordering Information




UNO
ADAM-4000
• Power Consumption
 PCL-812PG
Motion Control
eConnectivity
A/D pacer and counter (8254 compatible)
 A/D Pacer
 Max. and Min. Rates
 Counter
ADAM-3000
ICOM
Digital Output
 Channels
 Driving Capacity
cPCI
Last updated : January 2005
BAS
6-49
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-50
PCL-818 Series
High-Performance
Multifunction Cards
Features
 16 single-ended or 8 differential analog inputs
 12-bit A/D converter
 Programmable gain for each input channel
 Automatic channel/gain scanning with DMA
 16 digital inputs and 16 digital outputs
 One 12-bit analog output channel
 Programmable pacer/counter
Introduction
The PCL-818 series is a family of high-performance, multifunction cards that offer the five most desired measurement and control functions: 12-bit A/D conversion, D/A conversion,
digital input, digital output and counter/timer.
Automatic Channel/Gain Scanning
All PCL-818 cards feature an automatic channel/gain scanning circuit. This circuit, instead of your software, controls multiplexer switching during sampling. On-board SRAM stores
different gain values for each channel. This combination lets you perform multi-channel high-speed sampling (up to 100 kHz) with different gains for each channel and DMA data
transfer.
Unique Technology
PCL-818 cards share a custom-designed 160-pin ASIC chip that has a gate count of over 7,000 and utilizes 1.0 mm CMOS technology. This custom integration gives higher performance
and reliability with lower power consumption on a smaller board.
Wide Selection with Migration Path
The PCL-818 series lets you choose the card that exactly matches your application and price range. The PCL-818L is designed for lower budgets, with the best price/performance
ratio in the market. If you need more power, you can easily upgrade to any other card in the series.
Specifications
Digital Input/Output
 Channels
 Input Voltage
Analog Input
Channels
16 single-ended or 8 differential
Resolution
12 bits
Input Range Selection Software controlled
Auto Channel/Gain Scanning
Triggering
Software, pacer or external
Data Transfer
Program control, interrupt (IRQ 2 ~ 7)
or DMA (Ch. 1 or 3)
 Input Impedance
10 MΩ
 Input Overvoltage
±30 VDC max.






Analog Output (D/A Converter)
 Channels
 Output Range
One 12-bit (double-buffered)
0 ~ +5 V or 0 ~ +10 V with internal reference
0 ~ +10 V or 0 ~ -10 V with external reference
 Input Load
 Output Voltage
 Driving Capacity
16 inputs, 16 outputs (all TTL compatible)
Low (0 ~ +0.8 V)
High (min. +2.0 V)
Low: +0.5 V @ 0.4 mA max.
High: +2.7 V @ 0.05 mA max.
Low: 0 ~ +0.4 V
High: min. +2.4 V
Low: (sink) 8 mA @ 0.5 V max.
High: (source) -0.4 mA @ 2.4 V min.
A/D Pacer and Counter (8254)
 A/D Pacer
 Max. and Min. Rates
 Counter
32-bit with 10 MHz or 1 MHz time base
2.5 MHz to 0.00023 Hz
One 16-bit counter with 100 KHz time base
General
 Operating Temperature 0 ~ 50° C (32 ~ 122° F)
 Storage Temperature -20 ~ 65° C (-4 ~ 149° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCL-818L
40 kHz Multifunction Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
PCL-818L
 16 single-ended or 8 differential analog inputs
IPPC
 40 kHz 12-bit A/D converter
 Programmable gain for each input channel (up to 8)
 Automatic channel/gain scanning with DMA
TPC
 16 digital inputs and 16 digital outputs
PCL-818LS
 Low cost package of PCL-818L with PCLD-8115 and PCL-10137
FPM
ATM & AWS
DA&C
Introduction
The PCL-818L is the entry-level model in the PCL-818 series. We designed it with the cost-sensitive customer in mind. It offers the same functions as the rest of the series, except
that it has a 40 kHz sampling rate and only accepts bipolar inputs. It is fully software and connector compatible with the PCL-818HD and PCL-818HG. This lets you upgrade your
applications to these higher performance cards without hardware or software changes.
cPCI
ADAM-3000
The PCL-818LS Bundle
The PCL-818LS bundle consists of the PCL-818L card, the PCLD-8115 wiring terminal board and a DB37 cable assembly. The PCLD-8115 accommodates on-board passive signal
conditioning components (resistors and capacitors), allowing you to easily implement a low-pass filter, a voltage attenuator or a 4 ~ 20 mA voltage converter.
Motion Control
Specifications
Ordering Information
 PCL-818L
Analog Input
 Input Range (V)
 Maximum Sampling
Rate
 Accuracy
Bipolar: ±10, ±5, ±2.5, ±1.25, ±0.625
40 kS/s for all input ranges
Gain = 0.5, 1
Gain = 2, 4
Gain = 8
0.01% of FSR ±1 LSB
0.02% of FSR ±1 LSB
0.04% of FSR ±1 LSB
General
 Power Consumption
 I/O Ports
 A/D, D/A Connector
 Dimensions (L x H)
+5 V @ 210 mA typical, 500 mA max.
+12 V @ 20 mA typical, 100 mA max.
-12 V @ 20 mA typical, 40 mA max.
16 consecutive bytes
DB37
155 x 100 mm (6.1" x 3.9")
 PCL-818LS




PCL-10137-1
PCL-10137-2
PCL-10137-3
PCLD-8115
 PCLD-880
ICOM
Low-cost high-performance half-size multi-function
card, user’s manual and driver CD-ROM.(cable not
included)
PCL-818L with PCLD-8115 and DB-37 cable
assembly (PCL-10137-1)
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Industrial Wiring Terminal with CJC circuit and DB37
connector
Industrial Wiring Terminal with DB37 connector
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-51
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-52
PCL-818HD
PCL-818HG
High-Performance Half-Size
Multifunction Card
High-Performance Multifunction Card
Features
PCL-818HD
PCL-818HG
Introduction
Introduction
The PCL-818HD has guaranteed 100 kHz sampling and transfer speeds at all gains (x
1, 2, 4 or 8, programmable) and input ranges. It features an onboard 1 K sample FIFO
(First In First Out) buffer for faster data transfer and more predictable performance under
Windows.
The PCL-818HG offers the same functions as the PCL-818HD, but it features a special
high-gain programmable instrument amplifier for reading very low level input signals (x
0.5, 1, 5, 10, 50, 100, 500 or 1000).
Specifications
Analog Input
 Input Range (V)
Bipolar: ±10, ±5, ±2.5, ±1.25, ±0.625
Unipolar: 0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25
 Maximum Sampling Rate
100 kHz for all input ranges
 Accuracy
Gain = 0.5, 1
0.01% of FSR ±1 LSB
Gain = 2, 4
0.02% of FSR ±1 LSB
Gain = 8
0.04% of FSR ±1 LSB
General
 On-board Memory
 Power Consumption
 I/O Ports
 A/D, D/A Connector
 Dimensions (L x H)
1K samples FIFO for A/D. Can generate an interrupt
when full or half full
+5 V @ 500 mA max., +12 V @ 200 mA max
32 bytes with FIFO active or 16 bytes with FIFO
disabled
DB37
185 x 100 mm (7.3” x 3.9”)
Ordering Information
 PCL-818HD




PCL-10137-1
PCL-10137-2
PCL-10137-3
PCLD-8115
 PCLD-880
High-performance half-size multifunction card with
DB-37connector, user’s manual and driver CD-ROM
(cable not included)
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Industrial Wiring Terminal with CJC circuit and DB37
connector
Industrial Wiring Terminal with DB37 connector
The PCL-818HG package includes a special wiring board (PCLD-8115) with a DB-37
connector and CJC. This combination lets you measure low-level thermocouple signals
without an external signal-conditioning board.
Specifications
Analog Input
 Conversion Time
 Input Range (V)
8 µsec.
Bipolar: ±10, ±5, ±1, ±0.5, ±0.1, ±0.05, ±0.01, ±0.005
Unipolar: 0 ~ 10, 0 ~ 1, 0 ~ 0.1, 0 ~ 0.01
 Maximum Sampling Rate
(depends on input amplifier settling time and slew rate)
Gain
Speed
Channels
0.5, 1
100 kHz
Single (input signal £ 3 V p-p)
0.5, 1, 5, 10
35 kHz
Multiple
50, 100
7 kHz
Multiple
500, 1000
1 kHz
Multiple
 Accuracy
Gain = 0.5, 1
0.01% of FSR ±1 LSB
Gain = 5, 10
0.02% of FSR ±1 LSB
Gain = 50, 100
0.04% of FSR ±1 LSB
Gain = 500, 1000 0.08% of FSR ±1 LSB
General
See PCL-818HD
Ordering Information





PCL-818HG
PCL-10137-1
PCL-10137-2
PCL-10137-3
PCLD-8115
 PCLD-880
High-performance and High-gain multifunction card
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Industrial Wiring Terminal with CJC circuit and DB37
connector
Industrial Wiring Terminal with DB37 connector
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCL-813B
32-ch S.E. Isolated Analog Input Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 32 single-ended analog input channels
 Over 500 VDC isolation
IPPC
 12-bit successive approximation A/D converter
 Analog input ranges (V): ±5, ±2.5, ±1.25, ±0.625, 0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~
1.25
 Program-controlled A/D trigger and data transfer
TPC
FPM
ATM & AWS
PCL-813B
PCLD-881
PCL-10137
DA&C
Introduction
cPCI
The PCL-813B is a 12-bit 32-channel A/D card which offers high-voltage isolation on each analog input. The PCL-813B is an extremely cost effective solution for applications in
industrial measurement and monitoring. The card offers 32 A/D channels with software programmable gain on each channel and two DC-to-DC converters on a 4-layer PCB with an
integral ground plane. Optically-isolated inputs provide over 500 VDC of isolation between the analog inputs and the PC, protecting the PC and peripherals from damage due to high
voltages on the input lines. The PCL-813B is ideal for situations where the budget-conscious user requires flexibility, stability and a high level of isolation protection. The PCL-813B ADAM-3000
comes with the PCLD-881 wiring terminal board and a DB-37 cable assembly.
Specifications
Typical application for PCL-813B:
Input
ICOM
 Channels
 Resolution
 Input Ranges









32 single-ended with isolation
12 bits, SAR
Bipolar: ±5 V, ±2.5 V, ±1.25 V, ±0.625 V
(software programmable)
Unipolar: 0 ~ 10 V, 0 ~ 5 V, 0 ~ 2.5 V, 0 ~ 1.25 V
(jumper selectable)
Over Voltage
Continuous ±30 V (max.)
Converter
AD574 (or equivalent) w/25 µsec. conversion time
Data Transfer Rate
25 kHz maximum, software control only
Offset Error
0 ~ 5 V: ±1 LSB
+5 V, 0 ~ 10 V: ±2 LSB
Accuracy
0.01% of reading ±1 LSB
Isolation Voltage
> 500 VDC from analog input to PC
Trigger Mode
software trigger
Input Impedance
> 10 MΩ
Temperature Coefficient ±25 PPM/° C
General
 Power Consumption
+5 V @ 660 mA max.
+12 V @ 140 mA max.
 Operating Temperature 0 ~ 50° C (32 ~ 122° F)
 Storage Temperature -20 ~ 65° C (-4 ~ 149° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
 I/O Connector
DB37 female connector for input port
 Dimensions (L x H)
219 x 100 mm (8.6” x 3.9”)
eConnectivity
UNO
Industrial 4 ~ 20 mA Output Device Monitoring
Ordering Information
 PCL-813B





PCLD-881B
PCL-10137-1
PCL-10137-2
PCL-10137-3
ADAM-3937
ADAM-4000
32-ch. isolated analog input card, PCLD-881B wiring
terminal board, DB-37 cable assembly, manual and
driver
CD-ROM.
Industrial terminal board for PCI-1713 & PCL-813B
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
DB37 wiring terminal for DIN-rail mounting
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Motion Control
Last updated : January 2005
6-53
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-54
PCL-726
PCL-727
PCL-728
6-ch Digital Analog Output Card
12-ch Digital Analog Output Card
6-ch Analog Output Card
Features
 6 independent analog output channels
 12-bit resolution double-buffered D/A converter
 Multiple voltage ranges: ±10 V, ±5 V, 0 ~ +5 V, 0 ~ +10 V and 4 ~ 20 mA
current loop (sink)
 16 digital input channels and 16 digital output channels
Introduction
The PCL-726 provides six 12-bit D/A channels on a full-size add-on card. You can individually configure each channel to any of the following ranges: 0 to +5 V, 0 to +10 V, ±5 V,
±10 V and 4 to 20 mA current loop (sink). Designed for use in industrial environments, the PCL-726 is an ideal, economical solution for applications that require multiple analog
outputs or current loops.
In addition to its analog outputs, the PCL-726 also provides 16 digital output channels plus 16 digital input channels. Its TTL-compatible D/I and D/O ports easily interface with our
line of daughterboards for industrial On/Off control and sensing applications.
Specifications
General
 Power Consumption
Analog Output (D/A Converter)
 Channels
 Resolution
 Output Ranges








6
12 bits, double buffered
Unipolar: 0 ~ +5 V, 0 ~ +10 V
Bipolar: ±5 V, ±10 V
Current loop (sink): 4 ~ 20 mA, ±10 V with external DC
or AC reference
Throughput
15 kHz
Settling Time
≤ 70 µs
Accuracy
±0.012% full scale range
Temperature Drift:
5 PPM/° C (0° ~ 50° C)
Linearity
±½ bit
Voltage Output Current ±5 mA max.
Current Loop Excitation Minimum +8 V, maximum +36 V for 4 ~ 20 Voltage mA
Voltage
current loop
Reset (Power-on) Status all D/A channels will be at 0 V output after reset or
power-on (both bipolar and unipolar modes)
Digital Input




Channels
Logic Level 0
Logic Level 1
Input Loading
16-ch TTL compatible DI
0.8 V max.
2.0 V min.
0.5 V @ 0.4 mA max. (low)
2.7 V @ 50 mA max. (high)
Digital Output
 Channel
 Logic Level 0
 Logic Level 1
16-ch TTL compatible DO
0.5 V @ 8.0 mA (sink)
2.4 V @ 0.05 mA (source)
+5 V @ 500 mA typical, 1 A max.
+12 V @ 80 mA typical, 110 mA max.
-12 V @ 60 mA typical, 90 mA max.
 Operating Temperature 0 ~ 50° C (32 ~ 122° F)
 Storage Temperature 0 ~ 65° C (32 ~ 149° F)
 Operating Humidity
5% ~ 95% RH non-condensing (refer to IEC 68-2-3)
 Connectors
One 37-pin D type female connector
Two 20-pin male ribbon cable connectors
 Dimensions (LxH)
340 x 100 mm (13.4” x 3.9”)
Ordering Information
 PCL-726








PCL-727
PCL-728
PCL-10120-1
PCL-10120-2
PCLD-780
PCLD-782
PCLD-785
ADAM-3920
6-channel D/A output and DIO card, user’s manual and
driver CD-ROM (cable not included)
6-ch Digital Analog Output Card
12-ch Digital Analog Output Card
20-pin flat cable, 1 m
20-pin flat cable, 2 m
Screw terminal board
Opto-Isolated D/I board (16-ch)
Relay output board (16-ch)
20-pin wiring terminal for DIN-rail mounting
Applications





PID loop control
Programmable voltage source
Servo control
Programmable current sink
Function generator
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCL-720+
Digital I/O and Counter Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 32 TTL-level digital input channels
 32 TTL-level digital output channels
IPPC
 High-output driving capacity
 Low-input loading
 3 programmable counter/timer channels
TPC
 User configurable clock source
 Breadboard area for custom circuits
FPM
ATM & AWS
DA&C
Introduction
cPCI
The PCL-720+ digital I/O and counter card is a PC-compatible add-on card with 32 digital input channels, 32 digital output channels and three programmable counter/timer channels.
Its digital I/O channels are TTL-compatible and use 74LS244 driver/ buffer circuits to provide high output driving capacity. These buffered circuits also require lower input loading
current than regular TTL circuits. The PCL-720+’s 8254 programmable counter/timer provides three flexible 16-bit counter/timer channels. You can generate waves and pulses by
ADAM-3000
programming the 8254. Jumper settings determine the clock crystal frequency. The PCL-720+ also includes a breadboard area perfect for customized circuits.
Specifications
Ordering Information
 PCL-720
Digital Input
 Input Lines
 Logic Level 0
 Logic Level 1
32
0.8 V max.
2.0 V min.








Digital Output
 Output Lines
 Logic Level 0
 Logic Level 1
32
0.5 V max. @ 24 mA (sink)
2.0 V min. @ 15 mA (source)
Programmable Counter/Timer




Frequency Range
Counters
Modes
Usable Pins




Contact-closure monitoring
Switch-panel status sensor
BCD interface receiver
Digital signal interface
Eight consecutive bytes from hex 200 ~ 3F8
540 (30 x 18) plated-through "donuts", each with a
.036" hole on 0.10" centers. Further, provide +5 V on
the left side, and provide GND on the right side
 Power Consumption
+5 V @ 500 mA typical
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
 Connectors
Five 20-pin male ribbon-cable connectors
 Dimensions (L x H)
185 x 100 mm (7.3” x 4”)
UNO
ADAM-6000
 Industrial on/off controller
 Digital signal interface
 BCD interface driver
ADAM-8000
Counter/Timer
BAS
 Period and pulse-width measurement
 Event and frequency counting
 Waveform and pulse generation
Online Download www.advantech.com/products
All product specifications are subject to change without notice
eConnectivity
ADAM-5000
Digital Output
General
ICOM
ADAM-4000
Digital Input
2 MHz, 1 MHz, 500 kHz or 250 kHz; jumper selectable
Divided by 1, 10, 100 or user adjustable
 I/O Port Address
 Breadboard Area
Digital I/O and counter card, user’s manual, user’s manual
and driver CD-ROM (cable not included)
20-pin flat cable, 1 m
20-pin flat cable, 2 m
Screw terminal board
24/16 Channel opto-isolated D/I board
24/16 Channel relay output board
SSR and relay driver board
16-Channel power relay (form A) output board
20-pin flat cable wiring terminal for DIN-rail mounting
Applications
0 ~ 2.6 MHz
3 independent 16-bit counters
6 programmable modes
CLOCK and GATE for each channel
Clock Source
 Clock Frequency
 Frequency Divider
PCL-10120-1
PCL-10120-2
PCLD-780
PCLD-782
PCLD-785
PCLD-786
PCLD-885
ADAM-3920
Motion Control
Last updated : January 2005
6-55
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-56
PCL-722
PCL-724
PCL-731
144-bit Digital I/O Card
24-bit Digital I/O Card
48-bit Digital I/O Card
Features
PCL-722
PCL-724
Features
Specifications
 Emulates 8255 PPI mode 0
 Buffered circuits for higher driving capacity than the
8255
 Interrupt handing
 Output status readback
 Pin compatible with Opto-22 I/O module racks
 I/O Lines
 Programming Mode
 Interrupt
Specifications
 Digital Output
 I/O Lines
 Programming Mode
 Interrupts
144 (24 bits x 6 ports)
8255 PPI mode 0
bits 0 and 3 of Port C
can generate an interrupt
to IRQ 2, 3, 4, 5, 6 or 7
 Port C
Logic 0: 0.4 V max. @
12 mA (sink)
Logic 1: 2.4 V min. @
8.0 mA (source)
Logic 0: 0.5 V max. @
24 mA (sink)
Logic 1: 2.0 V min. @
15 mA (source)
Digital input
 Port A and Port B
 Port C
 Digital Input
Specifications
24
8255 PPI mode 0
Bit 0 of one port can
generate an interrupt to
IRQ2 ~ 7
Rising or falling edge
triggering, jumperselectable
Logic 0: 0.4 V max. @
24 mA (sink)
Logic 1: 2.4 V min. @
15 mA (source)
Logic 0: 0.4 V max.
Logic 1: 2.4 V min.
General
 Power Consumption
Digital output
 Port A and Port B
 Interrupt Triggering
PCL-731
Logic Level 0: 0.8 V max.
Logic Level 1: 2.0 V min.
Logic Level 0: 0.8 V max.
Logic Level 1: 2.0 V min.
General
+5 V @ 0.5 A (typical)
+5 V @ 0.8 A (max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 70° C
(-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH
non-condensing
(refer to IEC 68-2-3)
 Connectors
50-pin male
ribbon-cable connector
 Dimensions (L x H)
125 x 100 mm
(4.9” x 3.9”)
 I/O Lines
 Programming Mode
 Interrupt
 Interrupt Triggering
 Digital Output
 Digital Input
General
 Power Consumption
+5 V @ 0.5 A typical
+5 V @ 0.8 A max.
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 70° C
(-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH
non-condensing
(refer to IEC 68-2-3)
 Connectors
Two 50-pin male
ribbon-cable connectors
 Dimensions (L x H)
185 x 100 mm
(7.3” x 3.9”)
Ordering Information
 PCL-722
Pin Assignments
 PCL-724
 Power Consumption
+5 V @ 1.3 A typical
+5 V @ 1.8 A max.
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 70° C
(-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH
non-condensing (refer
to IEC 68-2-3)
 Connectors
Six 50-pin male ribboncable connectors. Pin
assignments are fully
compatible with Opto-22
I/O module racks
• Dimensions (L x H)
334 x 100 mm
(13.2” x 3.9”)
48
8255 PPI mode 0
Bit 0 of one port can
generate an interrupt to
IRQ 2~15
Rising or falling edge
triggering, jumperselectable
Logic 0: 0.4 V max. @
24 mA (sink)
Logic 1: 2.4 V min. @
15 mA (source)
Logic 0: 0.4 V max.
Logic 1: 2.4 V min.
 PCL-731
 PCL-10150-1.2
 PCLD-782B
 PCLD-785B
 PCLD-7216
 PCLD-885
 ADAM-3950
144-bit digital I/O card,
user's manual and driver
CD-ROM (cable not
included)
24-bit digital I/O card,
user's manual and driver
CD-ROM (cable not
included)
48-bit digital I/O card,
user’s manual and driver
CD-ROM (cable not
included)
50-pin flat cable, 1.2 m
24/16-ch. opto-isolated
digital input board
24/16-ch. relay output
board
16-ch. carrier board for
SSR I/O modules
16-ch. power relay
(Form A) output board
50-pin flat cable wiring
terminal for DIN-rail
mounting
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCL-725
PCL-735
Relay Actuator and Isolated Digital Input Card
12-ch Relay Actuator Card
Features
PCL-725
 8 relay outputs
IPPC
 8 optically-isolated digital inputs
 LED relay status indicators
 Isolated or non-isolated digital inputs
TPC
 Male DB37 matching connector included
PCL-735
FPM
 12 relay outputs
 LED relay status indicators
 Male DB37 matching connector included
ATM & AWS
 Relay status readback function
PCL-725
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
PCL-735
DA&C
Introduction
PCL-735 is a relay actuator card, while PCL-725 is combination of a relay actuator and isolated digital input card. Both half-size cards provide electromechanical SPDT relays. An cPCI
on-board DB-37 connector provides access to all input and output channels.
Specifications
PCL-735
PCL-725
Relay Output
Isolated Digital Input

















Input Channels
Opto-Isolator
Input Voltage
Input Resistance
Input Buffers
Threshold Voltage
Breakdown Voltage
Throughput
8
4N25
5 ~ 24 V
560 Ω (1 W @ 24 V input)
Voltage comparators
1.5 VDC, adjustable
300 VDC
10 kHz (max)
Relay Output
 Output Channels
 Relay Type
 Output Type
 Contact Rating







Breakdown Voltage
Relay on Time
Relay off Time
Total Switching Time
Insulation Resistance
Life Expectancy
Relay Driver
8
Single-pole double-throw (SPDT, Form C)
CH0 ~ CH3 with Normally Open and Normally Closed,
CH4 ~ CH7 with Normally Open only
120 VAC @ 0.5 A or
30 VDC @ 1 A
300 V AC/DC min.
5 ms. typical
5 ms. typical
10 ms. typical
100 MΩ min.
> 5 x 105 operations at AC: 110 V/0.3 A, DC: 24 V/1.25 A
+ 12 V @ 33 mA for each relay
General
 Power Consumption
+5 V @ < 0.2 A; +12 V @ 33 mA for each relay, < 0.27
A if all eight relays are energized
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
 I/O Port Address
Two consecutive bytes from hex 200 ~ 3F8
 Connector
37-pin D-type female connector
 Dimensions (L x H)
147 x 100 mm (5.75” x 3.9”)
Relay Type
Output Type
Contact Rating
Breakdown Voltage
Relay on Time
Relay off Time
Total Switching Time
Insulation Resistance
Life Expectancy
ADAM-3000
Single-pole double-throw (SPDT, Form C)
Ch0 to Ch11, normally open/normally closed
2 A @ 30 VDC, 1 A @ 125 VAC
1,000 VAC/DC min.
5 ms. typical
5 ms. typical
10 ms. typical
1,000 MΩ @ 500 VDC min.
> 5 x 105 operations @ 30 VDC and 2 A
> 2 x 106 operations @ 30 VDC and 1 A
General
 Power Consumption
+5 V @ 280 mA (typical)
+12 V @ 200 mA (max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Connector
One 37-pin D-type female connector
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
 I/O Port Address
Two consecutive bytes from hex 200 ~ 3F8
 Dimensions (L x H)
155 x 100 mm (6.1" x 3.9")
Ordering Information
 PCL-725
 PCL-735





PCL-10137-1
PCL-10137-2
PCL-10137-3
PCLD-880
ADAM-3937
Relay actuator and isolated D/I Card, user’s manual,
dirver CD-ROM and one DB-37 male connector (P/N:
PCL-10437-0)
12-channel relay actuator card, user's manual, driver
CD-ROM and one DB-37 male connector (P/N: PCL10437-0)
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Screw terminal board
DB37 wiring terminal for DIN-rail mounting
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
6-57
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-58
PCL-730
PCL-733
PCL-734
32-ch. Isolated Digital I/O Card
32-ch. Isolated Digital Input Card
32-ch. Isolated Digital Output Card
Features
PCL-730
PCL-733
PCL-734
Features
Features
Features
 32 isolated DIO channels (16 inputs and 16 outputs)
 32 isolated, bidirectional digital input channels
 32 isolated digital output channels
 32 TTL-level DIO channels (16 inputs and 16
outputs)
 High-voltage isolation (2,500 VDC)
 High output driving capacity
 Interrupt capacity
 High output driving capacity
 D-type connectors for isolated input channels
 High-voltage isolation on output channels (1,000
VDC)
 High-voltage isolation on isolated I/O channels
(2,500 VDC)
 Reverse voltage protection for isolated input
channels (up to 24 VDC)
 High sink current on isolated output channels (200
mA/channel)
 Interrupt capability
 Integral suppression diodes for inductive loads
 Two 20-pin connectors for isolated digital I/O
channels and two for TTL digital I/O channels
 Wide output range (5 ~ 40 VDC)
 D-type connectors for isolated output channels
 D-type connector for isolated input and output
channels
Introduction
The PCL-730/733/734 cards offer isolated digital input channels as well as isolated digital output channels with isolation protection up to 2,500 VDC, which makes it ideal for industrial
applications where high-voltage isolation is required. In addition, all output channels are provide high-voltage protection.
Specifications
General
PCL-730
Isolated Digital Input
PCL-730
PCL-733
Input Channels
16 (16-ch/group)
32 (16-ch/group)
Interrupt Inputs
2 (IDI0, IDI1)
2 (IDI0, IDI16)
Interrupt Level
2~7
2, 3, 5, 7, 10, 11, 12, 15
Input Voltage
1.2 kΩ @ 0.5 W
Optical Isolation
2,500 VDC
Temperature
PCL-730
PCL-734
Output Channels
16 (16-ch/group)
32 (16-ch/group)
Optical Isolation
2,500 VDC
1,000 VDC
Throughput
Sink Current
10 kHz
5 ~ 40 VDC
200 mA max./channel
Note:
185 x 100 mm (7.3" x 3.9")
Typical
+5 V @ 330
mA
+5 V @ 320
mA
+5 V @ 330
mA
Max.
+5 V @ 500
mA
+5 V @ 500
mA
+5 V @ 500
mA
Operating
Storage
Relative Humidity
Isolated Digital Output
Supply Voltage
Power
Consumption
PCL-734
37-pin D-type female
Dimensions (L x H)
5 ~ 24 VDC
Input Resistance
PCL-733
I/O Connector Type
0 ~ 60° C (32 ~ 140° F)
-20 ~ 70° C (-4 ~ 158° F)
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
The PCL-730 also provides 16-ch TTL Digital Input and 16-ch TTL Digital
Output. Please refer to the PCL-730 User’s Manual for the detail information.
Ordering Information
 PCL-730
 PCL-733
 PCL-734
 PCL-10120-1
 PCL-10120-2
32-channel isolated digital I/O card, user’s manual and
driver CD-ROM (cable not included)
32-channel isolated digital input card, user’s manual
and driver CD-ROM (cable not included)
32-channel isolated digital output card, user’s manual
and driver CD-ROM (cable not included)
20-pin flat cable, 1 m (for PCL-730 only)
20-pin flat cable, 2 m (for PCL-730 only)
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCL-730
PCL-733
PCL-734






PCL-10137-1
PCL-10137-2
PCL-10137-3
PCLD-782
PCLD-785
PCLD-786
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
16-channel opto-isolated D/I board (for PCL-730 only)
16-channel relay output board (for PCL-730 only)
8-channel SSR I/O module carrier board (for PCL-730
only)
16-channel power relay (form A) output board (for
PCL-730 only)
Universal screw terminal board
Universal screw terminal board
20-pin flat cable wiring terminal for DIN-rail mounting
(for PCL-730 only)
DB37 wiring terminal for DIN-rail mounting
 PCLD-885
 PCLD-780
 PCLD-880
 ADAM-3920
 ADAM-3937
Pin Assignments
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
IPPC
TPC
FPM
ATM & AWS
Applications
 Industrial On/Off control
DA&C
 Contact closure monitoring
 Switch status sensing
 BCD interfacing
cPCI
 Digital input control
 Industrial and lab automation
ADAM-3000
Motion Control
Isolated Input Circuit Diagram
DO
DI
IDO
IDI
E.GND
put
EI.GND
input
D.GND
PCOM
Digital output
Digital input
Isolated digital output
Isolated digital input
External ground for isolated outExternal common for isolated
Digital ground
Free wheeling common diode
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
Isolated Output Circuit Diagram
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-59
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-60
PCL-836
6-ch Counter/Timer Card
Features













Periodic interrupt generation
6 independent 16-bit counters
Digital filter for noise reduction
Binary or BCD counting
Programmable frequency output
Complex duty-cycle output
Single-shot output
16-bit TTL input and 16-bit TTL output ports
Selectable interrupt input channel
Up to 10 MHz input frequency
Pulsewidth and period measurement
Time-delay generation
F/V conversion and accumulation
Introduction
PCL-836 is a general purpose counter/timer and digital I/O card for PC/AT compatible computers. It provides six 16-bit counter channels. It also includes 16 digital outputs and 16
digital inputs. Two 8254 chips provide a variety of powerful counter/timer function modes to match your industrial and/or laboratory applications.
Unique Digital Filter
PCL-836 includes a unique digital filter to eliminate noise on the input signal. The frequency can be adjusted to provide more stable output readings.
Specifications
 PCLD-880
 ADAM-3937
Programmable Counter
 Counter
Six independent 16-bit counter channels
 Modes
Six programmable counter modes
 Programmable Digital 1.6 ms to 52 ms
Noise Filter
 3 PWM Output
 TTL Compatible Input/Output
 Interrupt
IRQ 2, 4, 5, 7, 10, 11, 12, 15 (jumper selectable)
Screw terminal board
DB-37 wiring terminal for DIN-rail mounting
Pin Assignments
Digital Input/Output
 16 TTL Input Channels Logic level 0: 0.8 V max.
Logic level 1: 2.4 V min.
 16 TTL Output Channels Logic level 0: 0.5 V max. @ 8 mA
Logic level 1: 2.4 V min. @ 0.4 mA
General
 Power Consumption
+5 V @ 360 mA (typical)
+5 V @ 400 mA (max.)
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 70° C (-4 ~ 158° F)
 Operating Humidity
5 ~ 95% RH non-condensing (refer to IEC 68-2-3)
• Connector
One 37-pin D-type female connector for counter I/O
Two 20-pin male flat-cable connector for digital I/O
185 x 100 mm (7.3" x 3.9")
• Dimensions (L x H)
Ordering Information
 PCL-836
 PCL-10137-1
 PCL-10137-2
 PCL-10137-3
6-channel counter/timer card, user’s manual and driver
CD-ROM (cable not included)
DB37 cable assembly, 1m
DB37 cable assembly, 2m
DB37 cable assembly, 3m
Applications




Event counting
Industrial automation (flowmeter/wattmeter monitoring)
Programmable frequency synthesis
Frequency counter
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCM-3712
PCM-3718H/HG/HO
PCM-3724
2-ch. Analog Output Module
12-bit Multifunction Module
with Programmable Gain
48-ch Digital I/O Module
NEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
IPPC
TPC
FPM
PCM-3712
PCM-3718H/HG
PCM-3724
Features
Features
Features
 Output status read back
 12-bit resolution
 16 single-ended or 8 differential analog inputs
 12-bit A/D converter, up to 100 KHz sampling rate
with DMA transfer
 Two 8-bit digital input/output TTL level channels
 One 12-bit Analog output channel (PCM-3718HO only)
Specifications
Specifications
Specifications
 2 channels analog output module
 0 to 5 V, 0 to 10 V, -2.5 V to +2.5 V, -5 V to +5 V, -10
V to +10 V,or 4 to 20 mA output range














Analog Output Channels 2
Voltage Range Unipolar 0 to 5 V, 0 to 10 V
Bipolar
± 2.5 V, ±5 V, ±10 V
Current Range
4 ~ 20 mA
Output Current Range ±5 mA
Impedance
0.1 max./0.02 typ.
Resolution
12-bit
Nonlinearity
±1 LSB
Differential Nonlinearity ±1/2 LSB
System Accuracy
±0.025% FSR (Voltage)
±0.05% FSR (Current)
Dynamic Performance 5 V step: 16 µs
0.3V/µs typ. (Voltage)
1.2mA/µs (Current)
Settling Time to 1/2 LSB 10 V step: 33 µs
Slew Rate
0.3 V/µs typ. (Voltage)
1.2 mA/µs (Current)
D/A Converter Single 33 kHz bit resolution
Channel
Ordering Information
 PCM-3712
 ADAM-3909
2-channel analog output
module (18 cm Flat
Cable 10-pin to DB9 (F)
included)
DB9 cable wiring for
DIN-rail mounting
Analog Input
 Channels
16 single-ended or 8
differential inputs
12 bits
 Resolution
Analog Output
 Channel
 Output Range
One 12-bit
0 ~ +5V or 0 ~ +10V with
int. reference
0 ~ +10V or 0 ~ -10V
with ext. reference
Bipolar: ±10, ±5, ±1,
±0.5, ±0.1, ±0.05, ±0.01,
±0.005
Unipolar
(PCM-3718HG): 0 ~ 10,
0 ~ 1, 0 ~, 0 ~ 0.01
 Input Range
Digital Input/Output
 Channels
 Input Voltage
 Output Voltage
 Power Requirements
 Temperature
Two 8-bit TTL-level
Digital I/O channels
Logic 0: 0.8 V max.
Logic 1: 2.0 V min.
Logic 0: 0.33 V max. @
6 mA (sink)
Logic 1: 3.84 V min. @
6 mA (source)
+5 V, ±5 % tolereance on
power supply
Operating: 0 ~ 60° C
(32 ~ 140° F)
Storage : -40 ~ 85° C
(-40 ~ 185° F)
Ordering Information
 PCM-3718H
 PCM-3718HG
 PCM-3718HO
 ADAM-3920
 PCLD-780
 PCL-10120-1
 PCL-10120-2
12-bit multifunction
module with
progammable gain (cable
not included)
PCM-3718H w/high gain
PCM-3718H w/AO
20-pin flat cable wiring
terminal for DIN-Rail
mounting
Screw-terminal board for
20-pin flat cable
20-pin flat cable, 1 m
20-pin flat cable, 2 m
ATM & AWS
 Channels simulate 8255 PPI mode 0
 Interrupt triggering, rising/falling edge
cPCI
Digital I/O
 Channels
 Throughput
 Input Voltage
 Output Voltage
 Power Requirements
 Size/Weight
 Temperature
 Operating Humidity
ADAM-3000
48 digital I/O channels
300 kbps typical
400 kbps max.
Logic 0: 0.8 V max.
Logic 1: 2.0 V min.
Logic 0: 0.5 V max. @
24 mA (sink)
Logic 1: 2.0 V min. @
15 mA (source)
+5 V, ±5 % tolerance on
power supply
96 x 90 mm (3.8"x 3.5"),
0.084 kg (0.185 lb)
Operating: 0 ~ 60° C
(32 ~ 140° F)
Storage : -40 ~ 85° C
(-40 ~ 185° F)
0 ~ 90% relative
humidity,
non-condensing
Motion Control
ICOM
eConnectivity
UNO
ADAM-4000
ADAM-5000
Ordering Information
 PCM-3724
 ADAM-3950
 PCLD-785B
 PCLD-782B
 PCL-10150-1.2
48-channel digital
I/O module (cable not
included)
50-pin flat cable wiring
terminal for DIN-Rail
mounting
24-channel relay output
board
24-channel
opto-isolated digital
input board
50-pin flat cable, 1.2 m
Online Download www.advantech.com/products
All product specifications are subject to change without notice
DA&C
Last updated : January 2005
ADAM-6000
ADAM-8000
BAS
6-61
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-62
PCM-3725
PCM-3730
PCM-3780
8-ch Isolated DI and 8-ch Relay Output Module
16-ch Isolated Digital I/O Module
3-ch Counter/Timer with 24-ch TTL DI/O Module
PCM-3725
PCM-3730
Features
Features
Specifications
 LED indicators to show activated relays
 High output driving capacity and high-voltage
isolation
 Interrupt capability
 High sink current on isolated output channels
Programmable counter
 Interrupt handling capability
Specifications
Isolated Digital Input
 Channels
Opto-Isolated 8 DI
channels
 Over-Voltage Protection 70 VDC
 Isolation Voltage
2500 VDC
 Isolator Response Time 25 µs
 Channels
 Nominal Switch
8-ch SPDT (Form C)
relays
1.5 A @ 30 VDC
Capacity




Switching Power
Switching Voltage
Switching Current
Breakdown Voltage
45 W max.
220 VDC max.
1.5 A max.
2000 VRMS for 1 min.
General
 Power Consumption
100 mA @ +5 V
(typical); 280 mA @ +5
V ( max)
 Isolated DI Connector 20-pin post header
 Relay Output Connector 50-pin post header
Ordering Information
 PCM-3725




PCL-10120-1
PCL-10120-2
PCL-10150-1.2
ADAM-3920
 ADAM-3950
 PCLD-780
Specifications
 Power Consumption
8-ch Isolated Digital
Input and 8-ch Relay
Output Module, user’s
manual and driver
CD-ROM. (cable not
included)
20-pin Flat Cable 1m
20-pin Flat Cable 2m
50-pin Flat Cable 1.2m
20-pin Flat Cable Wiring
Terminal for DIN-Rail
50-pin Flat Cable Wiring
Terminal for DIN-Rail
Screw-Terminal Board
for 20-pin Flat Cable
330 mA @ +5 V
(typical); 500 mA @ +5
V (max)
Isolated Digital I/O
 Channels
Relay Output
PCM-3780
 Input Resistance
 Output Voltage
 Output Sink Current
 Isolation Voltage
 Throughput
Opto-Isolated 8DI and
8DO
2 kΩ @ 0.5 W
Open collector 5 to
40 VDC
200 mA max.
2,500 VDC
10 kHz max.
TTL-level Digital I/O
 Channels
 Input Voltage
 Output Voltage
 Input Load
 Throughput
TTL-level 16DI and
16DO
Low: 0.8 V max.
High: 2.0 V min.
Low: Sink 8 mA @ 0.5 V
max.
High: Source -0.4 mA
@ 2.4 V min.
Low: 0.4 mA @ 0.5 V
max.
High: 0.05 mA @ 2.7
V max.
30 kHz typical
Ordering Information
 PCM-3730
 PCL-10120-1
 PCL-10120-2
 ADAM-3920
 PCLD-780
 PCLD-785/885
16-ch isolated digital I/O
module, user’s manual
and driver CD-ROM.
(cable included)
20-pin flat cable, 1m
20-pin flat cable, 2m
20-pin flat cable wiring
terminal for DIN-Rail mt.
Screw-terminal board for
20-pin flat cable
16-ch relay/power relay
output board
 3 independent 16-bit counters
 4 independent programmable clock sources
(10 M, 1 M, 100 K, 10 K)
 12 programmable counter modes
 TTL compatible logical level
 Maximum frequency 20 MHz
Digital input/output
 24 TTL input/output channels (8255 mode 0)
Input: Logic 0: 0.8V max.
Logic 1: 2.4V min.
Output TTL output channels:
Logic 0: 0.5 V max. @ 24 mA (sink)
Logic 1: 2.4 V min. @ 15 mA (source)
Counter/Timer




Channels
Resolution
Compatibility
Max. Input Frequency
3
16-bit
TTL level
20 MHz
General
 I/O Connector Type
 Dimensions
 Power Consumption
One 50 pin and one 20
pin box header
175 x 99 mm
(6.9” x 3.9")
Typical: +5 V @ ? mA
Max.: +5 V @ ? A
 Temperature
Operating: 0 ~ 60° C (32 ~ 158° F)
(refer to IEC 68-2-1, 2)
Storage: -20 ~ 70° C (-4 ~ 158° F)
 Relative Humidity
Operating: 5 ~ 85%RH non-condensing (refer to IEC
68-1,-2,-3)
Storage: 5 ~ 95%RH non-condensing (refer to IEC
68-1,-2,-3)
Ordering Information
 PCM-3780
 PCL-10120-1
 PCL-10150-1.2
 ADAM-3920/50
3-ch Counter/Timer with
24ch TTL DIO Module
20-pin Flat Cable 1m
50-pin Flat Cable 1.2m
20/50-pin Flat Cable
Wiring Terminal for
DIN-Rail
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PCI-1670
GPIB Interface PCI-bus Card
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Complete IEEE 488.2 compatibility
 Supports Windows® 95/98/NT/ME/2000/XP and DOS.
 Full driver, library, and example support, including Visual C++®, C++
Builder®, LabWindows/CVI, Visual Basic®, Delphi® and LabView® drivers.
 Provides NI-like driver & function libraries.
IPPC
TPC
 PCI bus specification 2.1 compliant
 I/O address automatically assigned by PCI Plug & Play
 Provides powerful and easy-to-use configuration utility
FPM
ATM & AWS
DA&C
Introduction
PCI-1670 is a high-performance PCI-bus card with a GPIB interface. The card is fully compatible with IEEE 488.1 and 488.2 standards with its PCI 2.1 bus specification. With two
driver control modes: controller mode and slave mode; PCI-1670 can perform basic the IEEE 488 talker, listener and controller functions required by IEEE 488.2. You can also connect
up to 15 GPIB instruments. Therefore, PCI-1670 is especially suitable for instrument measurements and control.
PCI-1670 is available for Windows® 95/98/NT/ME/2000/XP and DOS, and it supports complete drivers and libraries. To make driver development easier, PCI-1670 comes with
example drivers programmed in: Visual C++®, C++ Builder®, Labwindows/CVI®, Visual Basic®, Delphi® and LabVIEW®.
Furthermore, PCI-1670 also offers powerful testing features and a configuration utility that allows users to easily access and control instruments.
PCI-1670 offers a comprehensive supplementary controller driver database and provides NI-like commands to help users develop applications. Users can use an interactive GPIB
window interface to control devices directly without any need of programming.
cPCI
ADAM-3000
Motion Control
ICOM
Specifications
Ordering Information
Bus interface
PCI specification 2.1 compliant
IRQ and I/O memory automatically assigned by PCI plug-and-play
IEEE 488, IEEE 488.1 and IEEE 488.2 standard compatible
A maximum of 15 GPIB-instruments can be connected.
Connector
IEEE 488 standard 24-pin
Speed
GPIB-bus transfer rate up to 1M bytes/sec
OS
Windows® 95/98/NT/2000/XP, DOS
Libraries
Visual C++, Borland C++ Builder, LabWindows/CVI,
Visual Basic, Delphi, Labview
 Dimensions
131 x 106 mm (5.15” x 4.17”)
 Operating Temperature 0 ~ 55° C
 Operating Humidity
10 ~ 90% Relative Humidity, non-condensing.












PCI-1670
PCL-10488-1
PCL-10488-2
PCL-10488-4
GPIB Interface PCI-bus Card, IEEE-488 Cable, 2M
IEEE-488 Cable, 1M
IEEE-488 Cable, 2M
IEEE-488 Cable, 4M
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-63
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-64
PCI-1671
High-Performance IEEE-488.2
Interface for PCI-Bus Computers
Features
NEW
 IEEE 488.2 Standard interface
 Complete Talker/Listener/Controller
 Industry standard 32-bit PCI bus
 Data transfer rates over 1 Megabytes/sec
 REP-INSW block transfer
 1024-word FIFO buffer
 High-Speed State Machine Bus Manager
 7 Interrupt lines, shared interrupt capability
 Transparent interrupt enabling/disabling
 Includes GPIB-Library software
Introduction
The PCI-1671 IEEE-488 interface converts any PCI bus personal computer into an instrumentation control and data acquisition system. Connect up to 14 instruments using standard
IEEE-488 cables such as the PCL-10488-2, 2 meter IEEE-488 interface cable.
Greater than 1MB/s Transfer Rates
The PCI-GPIB transfers data over the GPIB at rates in excess of 1 million bytes per second using the maximum IEEE-488 specification cable length (2 meters times the # of devices).
A 1024-word FIFO buffer and the advanced REP-INSW ISR data transfer method provide the horsepower required to then transfer the data between the GPIB board and the host
computer. The high-speed state machine also provides byte-to-word packing and unpacking, and because words carry twice the information that bytes do, packed data requires fewer
bus cycles to transfer the same GPIB information.
IEEE-488.2 (GPIB) Compatibility
The PCI-GPIB adheres to ANSI/IEEE Standard 488-1978. Often referred to as the IEEE-488.2 bus, GPIB bus or HP-IB bus, the GPIB (General Purpose Interface Bus) is a standard for
instrumentation communication and control for instruments from manufacturers the world over. The GPIB provides handshaking and interface communications over an 8-bit data bus
employing 5 control and 3 handshake signals. Equipped with a PCI-1671, a personal computer can:
Control GPIB instruments, gather data from GPIB test equipment, or become a data acquisition station in a GPIB system.
Software
The PCI-1671 includes powerful GPIB-Library. The library greatly simplifies your programming effort. The PCI-1671 is also supported by a wide variety of application software
packages including SoftWIRE®, LabVIEW® and many others.
Windows® 95/98/2000/XP and DOS Compatibility
The PCI-GPIB hardware supports all popular operating systems and languages regardless of the operating systems support for Plug & Play. The installation software will manage
resources for you on systems without Plug & Play.
Specifications
 IEEE Compatibility
 Maximum Transfer
Rate
 Power
 I/O Connector
 Operating Temperature
and Humidity
 Storage Temperature
& Humidity
Ordering Information
IEEE-488.1 and IEEE-488.2
>1 Mbyte/s
5 VDC @ 375 mA Typical
IEEE-488 Standard 24 pin
0 ~ 60° C @ 0-90% RH
 PCI-1671
 PCL-10488-1
 PCL-10488-2
 PCL-10488-4
High-Performance IEEE-488.2 Interface for PCI-Bus
Computers
IEEE-488 Cable, 1M
IEEE-488 Cable, 2M
IEEE-488 Cable, 4M
-40 ~ 100° C @ 5-90% RH
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
USB-4711
100 kS/s, 12-bit USB Multifunction Module
Features
NEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports USB 2.0
IPPC
 Portable
 No need for external power
 16 analog input channels
TPC
 12-bit resolution AI
 Sampling rate up to 100 kS/s
 8DI/8DO, 2 AO and 1 16-bit counter (USB-4711L w/o AO)
 Wiring terminal on Modules
FPM
ATM & AWS
DA&C
Introduction
The USB-4700 series consists of true Plug & Play data acquisition modules. No more opening up your computer chassis to install boards. Just plug in the module, then get the data.
It’s easy and efficient.
USB-4711 offers 16SE / 8DI inputs with 12-bit resolution, up to 100 kS/s throughput, 16 digital I/O lines and 1 user counter/timers, and optional 12-bit analog outputs.
Reliable and rugged enough for industrial applications, yet inexpensive enough for home projects, USB-4711 is perfect for adding measurement and control capability to any computer
with an USB port. USB-4711 is fully USB Plug & Play compatible and easy to use. It obtains all required power from the USB port, so no external power supply is required.
cPCI
ADAM-3000
Motion Control
Specifications
Ordering Information
 USB-4711
Analog Input









Channels
Resolution
FIFO Size
Sampling Rate
Conversion Time
Input Range
Input Protection
Input Impedance
Trigger Mode Software
100 kS/s, 12-bit USB multifunction module
16 Single-Ended
12-bit
1K samples
100 kS/s max.
10 µs
± 10 V ± 5 V ± 2.5 V ± 1.25 V ± 0.625 V
30 Vp-p
2 Ω/5 pF
On-board or external programmable pacer
eConnectivity
UNO
ADAM-4000
Digital Input / Output
 Input Channels
 Input Voltage
 Output Channels
 Output Voltage
8
Low 0.8 V max.
High 2.0 V max.
8
Low 0.8 V max.@ 0.8 mA (sink)
High 2.0 V min.@ -0.4 mA (source)
ADAM-5000
ADAM-6000
Analog Output
 Channels
 Resolution
 Throughput
ICOM
ADAM-8000
2
12-bit
100 kS/s
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-65
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-66
USB-4716
100 kS/s, 16-bit USB Multifunction Module
Features
NEW
 Supports USB 2.0
 Portable
 No need for the external power
 16 analog input channels
 16-bit resolution AI
 Sampling rate up to 100 kS/s
 16 DIO, 2 AO and 1 32-bit counter (USB-4716L w/o AO)
 Wiring terminal on Modules
Introduction
The USB-4700 series consists of true Plug & Play data acquisition devices. No more opening up your computer chassis to install boards-just plug in the module, then get the data. It’s easy
and efficient. USB4716 offers 16SE inputs with 16-bit resolution, up to 100 kS/s throughput, 16 digital I/O lines and 2 user counter/timers, and optional 12-bit analog outputs.
Reliable and rugged enough for industrial applications, yet inexpensive enough for home projects, the USB-4716 is the perfect way to add measurement and control capability to any
USB capable computer. The USB-4716 is fully USB Plug & Play and easy to use. It obtains all required power from the USB port, so no external power connection is ever required.
Specifications
Digital Input / Output
 Input Channels
 Input Voltage
Analog Input









Channels
Resolution
Max. SPS
Conversion Time
Input Range/Gain
Max Input Overvoltage
Trigger Mode
DC/INL/DNL/..
AC/SNR/ENOB
16 Single-Ended
16-Bit
100 kS/s
10 µs
/Bi-polar By GainGain = 1, 2, 4, 8
+/- 15V
Software / Internal Or External Pacer
+/-1LSB / Gain Error
68dB / 11-Bit
Analog Output




Channels
Resolution
Ranges
Accuracy
2
16-Bit
0 ~ 5V, 0 ~ 10V
DNL/INL = +/-1LSB
 Output Channels
 Output Voltage
6
Low 0.8 V max.
High 2.0 V max.
16
Low 0.8 V max.@ 0.8 mA (sink)
High 2.0 V min.@ -0.4 mA (source)
Programmable Counter / Timer





Channels
Resolution
Compatibilty
Base Clock
Max. Input Frequency
1
16-bit
TTL Level
10 MHz
10 MHz
Ordering Information
 USB-4716
100 kS/s, 16-bit USB multifunction module
Plug-in DA&C Cards
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
USB-4718
NEW
8-channel Thermocouple Input Module
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports USB 2.0
 Portable
IPPC
 No need for the external power
 8 thermocouple input channels
 3000 VDC isolation
TPC
 Supports 4~20mA
 Wiring terminal on Modules
FPM
ATM & AWS
DA&C
Introduction
The USB-4700 series consists of true Plug & Play data acquisition devices. No more opening up your computer chassis to install boards-just plug in the module, then get the data.
It’s easy and efficient. USB4718 offers 8 thermocouple inputs with 16-bit resolution, up to 0.1% input range accuracy, or 4~20mA inputs.
cPCI
Reliable and rugged enough for industrial applications, yet inexpensive enough for home projects, the USB-4718 is the perfect way to add measurement and control capability to any USB ADAM-3000
capable computer. The USB-4718 is fully USB plug and play and easy to use. It obtains all required power from the USB port, so no external power connection is ever required.
Specifications
Analog Input










Ordering Information
 USB-4718
Motion Control
8-channel Thermocouple Input Module
ICOM
Effective Resolution
Channels
Ch. Independent Conf.
lnput Type
T/C Type and
Temperature Ranges
16-bit
8 differential
Yes
T/C & 4~20 mA
J 0 ~ 760° C
R 500 ~1750° C
K 0 ~ 1370° C
S 500 ~1750° C
T -100 ~ 400° C
B 500 ~1800° C
E 0 ~ 1000° C
Isolation Voltage
3000 VDC
Fault and Over-voltage Resists over-voltage up to 35 V
Protection
Sampling Rate
10 samples/sec
Accuracy
0.1% for voltage input
CMR @ 50/60 Hz
92 dB min
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
6-67
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
6-68
ISA-Compatible PCI Cards
Advantech ISA-Compatible Series
To support current ISA I/O card users and help the migration to PCI, Advantech has released several PCI I/O cards that are compatible with existing ISA cards.
The new PCI cards are compatible with the ISA cards’ functions, connectors, and software APIs.
With functionally compatible PCI cards, ISA users can upgrade design-ready objects from their ISA platform to the PCI platform, and enjoy the improved performance of a new
computer. With connector compatibility, ISA users can keep using all accessories, including the connected wiring boards and circuits. Lastly, the ISA-compatible cards use the same
software API as the ISA cards, so there is no need to re-write the program when upgrading the system.
The ISA-compatible PCI cards are designed to assist users who would like to transfer their current application to a new platform in the shortest time possible. This not only saves
time and money, but also raises the efficiency of the design. Following is a list of ISA-compatible products.
PCI
ISA
Product Features
Page
PCI-1718HDU
PCL-818HD
12-bit 16-ch Multifunction
6-18
PCI-1718HGU
PCL-818HG
12-bit 16-ch High-Gain Card
6-18
PCL-727
12-ch Analog Output Card
6-30
Multifunction Cards
Analog Output
PCI-1727U
Isolated Digital IO Cards
PCI-1730
PCL-730
16/16 Isolated Digital IO Card
6-34
PCI-1733
PCL-733
32-ch Isolated Digital Input Card
6-34
PCI-1734
PCL-734
32-ch Isolated Digital Output Card
6-34
PCL-725
8-Relay, 8 Isolated DI Card
6-44
Relay Cards
PCI-1761
Plug-in DA&C Cards
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising