Chrysler | Jeep Wrangler | User guide | Chrysler Jeep Wrangler User guide

Chrysler Jeep Wrangler User guide
User Guide
2013
Wrangler
Includes Wrangler Unlimited
If you are the first registered retail owner of
your vehicle, you may obtain a complimentary
printed copy of the Owner’s Manual, Navigation/
Uconnect® Manuals or Warranty Booklet by calling
1-877-426-5337 (U.S.) or 1-800-387-1143 (Canada)
or by contacting your dealer.
The driver’s primary responsibility
is the safe operation of the
vehicle. Driving while distracted
can result in loss of vehicle
control, resulting in a collision and
personal injury. Chrysler Group
LLC strongly recommends that
the driver use extreme caution
when using any device or feature
that may take their attention off
the road. Use of any electrical
devices such as cell phones,
computers, portable radios,
vehicle navigation or other
devices by the driver while the
vehicle is moving is dangerous
and could lead to a serious
collision. Texting while driving is
also dangerous and should never
be done while the vehicle is
moving. If you find yourself
unable to devote your full
attention to vehicle operation,
pull off the road to a safe location
and stop your vehicle. Some
States or Provinces prohibit the
use of cellular telephones or
texting while driving. It is always
the driver’s responsibility to
comply with all local laws.
Important:
This User Guide is intended to familiarize you with the important features
of your vehicle. The DVD enclosed contains your Owner’s Manual,
Navigation/Uconnect® Manuals, Warranty Booklets, Tire Warranty
and Roadside Assistance (new vehicles purchased in the U.S.) or
Roadside Assistance (new vehicles purchased in Canada) in electronic
format. We hope you find it useful. Replacement DVD kits may be
purchased by visiting www.techauthority.com. Jeep® is a registered
trademark of Chrysler Group LLC. Copyright 2012 Chrysler Group LLC.
TABLE OF CONTENTS
INTRODUCTION/WELCOME
OFF-ROAD CAPABILITIES
WELCOME FROM CHRYSLER
GROUP LLC . . . . . . . . . . . . . . . . . . 2
COMMAND-TRAC®/ROCK-TRAC® . . . . . 86
AXLE LOCK (TRU-LOK®)
RUBICON ONLY . . . . . . . . . . . . . . . 87
ELECTRONIC SWAY BAR
DISCONNECT – RUBICON ONLY . . . . 87
CONTROLS AT A GLANCE
DRIVER COCKPIT . . . . . . . . . . . . . . 6
INSTRUMENT CLUSTER . . . . . . . . . . 8
GETTING STARTED
KEY FOB . . . . . . . . . . . .
REMOTE START . . . . . . .
THEFT ALARM . . . . . . . . .
SEAT BELT . . . . . . . . . . .
SUPPLEMENTAL RESTRAINT
SYSTEM (SRS) — AIR BAGS
CHILD RESTRAINTS . . . . .
FRONT SEATS . . . . . . . . .
REAR SEATS . . . . . . . . . .
TILT STEERING COLUMN . .
HEATED SEATS . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
10
10
11
11
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
13
15
17
18
19
OPERATING YOUR VEHICLE
ENGINE BREAK-IN
RECOMMENDATIONS . . . . . .
TURN SIGNAL/LIGHTS LEVER .
WIPER/WASHER LEVER . . . . .
SPEED CONTROL . . . . . . . . .
MANUAL CLIMATE CONTROLS .
AUTOMATIC TEMPERATURE
CONTROLS (ATC) . . . . . . . . .
SUNRIDER® AND SOFT TOP . .
HARD TOP AND FREEDOM TOP®
DUAL TOP — IF EQUIPPED . . .
WIND BUFFETING . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
20
21
22
23
24
...
...
..
...
...
.
.
.
.
.
.
.
.
.
.
25
26
35
38
39
ELECTRONICS
YOUR VEHICLE'S SOUND SYSTEM . .
Uconnect® 130 . . . . . . . . . . . . . .
Uconnect® 130 WITH SiriusXM™
SATELLITE RADIO . . . . . . . . . . . . .
Uconnect® 230 . . . . . . . . . . . . . .
Uconnect® 430/430N . . . . . . . . . .
Uconnect® 730N . . . . . . . . . . . . .
SiriusXM™ SATELLITE RADIO/TRAVEL
LINK . . . . . . . . . . . . . . . . . . . . .
STEERING WHEEL AUDIO
CONTROLS . . . . . . . . . . . . . . . .
iPod®/USB/MP3 CONTROL . . . . . . .
Uconnect® Phone . . . . . . . . . . . . .
Uconnect® VOICE COMMAND . . . . . .
Bluetooth® STREAMING AUDIO . . . .
ELECTRONIC VEHICLE INFORMATION
CENTER (EVIC) . . . . . . . . . . . . . .
PROGRAMMABLE FEATURES . . . . . .
POWER INVERTER . . . . . . . . . . . .
POWER OUTLETS . . . . . . . . . . . .
. 40
. 42
.
.
.
.
44
47
50
60
. 71
.
.
.
.
.
75
75
76
79
82
.
.
.
.
82
83
84
85
UTILITY
TRAILER TOWING WEIGHTS
(MAXIMUM TRAILER WEIGHT
RATINGS) . . . . . . . . . . . . . . . . . . 88
RECREATIONAL TOWING
(BEHIND MOTORHOME, ETC.) . . . . . 90
WHAT TO DO IN EMERGENCIES
ROADSIDE ASSISTANCE . . . . . . . . . . 94
INSTRUMENT CLUSTER
WARNING LIGHTS . . . . . . . . . . . . . 94
IF YOUR ENGINE OVERHEATS . . . . . . 98
JACKING AND TIRE CHANGING . . . . . 99
JUMP-STARTING . . . . . . . . . . . . . 104
EMERGENCY TOW HOOKS . . . . . . . 106
SHIFT LEVER OVERRIDE . . . . . . . . 106
TOWING A DISABLED VEHICLE . . . . 107
FREEING A STUCK VEHICLE . . . . . . 107
EVENT DATA RECORDER (EDR) . . . . 108
MAINTAINING YOUR VEHICLE
OPENING THE HOOD . . . . . .
ENGINE COMPARTMENT . . . .
FLUIDS AND CAPACITIES . . . .
MAINTENANCE SCHEDULE . .
MAINTENANCE RECORD . . . .
FUSES . . . . . . . . . . . . . . . .
TIRE PRESSURES . . . . . . . .
WHEEL AND WHEEL TRIM CARE
EXTERIOR BULBS . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
109
110
111
113
118
119
123
124
124
CONSUMER ASSISTANCE
CHRYSLER GROUP LLC
CUSTOMER CENTER . . . . . . . .
CHRYSLER CANADA INC.
CUSTOMER CENTER . . . . . . . .
ASSISTANCE FOR THE HEARING
IMPAIRED . . . . . . . . . . . . . .
PUBLICATIONS ORDERING . . . .
REPORTING SAFETY DEFECTS IN
THE 50 UNITED STATES AND
WASHINGTON, D.C. . . . . . . . .
. . . 125
. . . 125
. . . 125
. . . 125
. . . 126
MOPAR ACCESSORIES
AUTHENTIC ACCESSORIES BY
MOPAR® . . . . . . . . . . . . . . . . . . . 127
INDEX . . . . . . . . . . . . . . . . . . 128
FAQ (How To?)
FREQUENTLY ASKED QUESTIONS . . . 131
INTRODUCTION/WELCOME
WELCOME FROM CHRYSLER GROUP LLC
Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it
represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's
control under some driving conditions. These are to assist the driver and are never a
substitute for attentive driving. They can never take the driver's place. Always drive
carefully.
Your new vehicle has many features for the comfort and convenience of you and your
passengers. Some of these should not be used when driving because they take your
eyes from the road or your attention from driving. Never text while driving or take your
eyes more than momentarily off the road.
This guide illustrates and describes the operation of features and equipment that are
either standard or optional on this vehicle. This guide may also include a description
of features and equipment that are no longer available or were not ordered on this
vehicle. Please disregard any features and equipment described in this guide that are
not available on this vehicle. Chrysler Group LLC reserves the right to make changes
in design and specifications and/or make additions to or improvements to its
products without imposing any obligation upon itself to install them on products
previously manufactured.
This User Guide has been prepared to help you quickly become acquainted with the
important features of your vehicle. It contains most things you will need to operate
and maintain the vehicle, including emergency information.
The DVD includes a computer application containing detailed owner's information
which can be viewed on a personal computer or MAC computer. The multimedia DVD
also includes videos which can be played on any standard DVD player (Uconnect®
Touch-Screen Radios). Additional DVD operational information is located on the back
of the DVD sleeve.
For complete owner information, refer to your Owner's Manual on the DVD in the owner’s
kit provided at the time of new vehicle purchase. For your convenience, the information
contained on the DVD may also be printed and saved for future reference.
Chrysler Group LLC is committed to protecting our environment and natural resources. By converting from paper to electronic delivery for the majority of the user
information for your vehicle, together we greatly reduce the demand for tree-based
products and lessen the stress on our environment.
This is a specialized utility vehicle designed for both on-road and off-road use. It can
go places and perform tasks for which conventional two-wheel drive enclosed vehicles
were not intended. It handles and maneuvers differently from many passenger cars
both on-road and off-road, so take time to become familiar with your vehicle.
2
INTRODUCTION/WELCOME
VEHICLES SOLD IN CANADA
With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be
deemed to be deleted and the name Chrysler Canada Inc. used in substitution
therefore.
WARNING!
• Pedals that cannot move freely can cause loss of vehicle control and increase
the risk of serious personal injury.
• Always make sure that objects cannot fall into the driver foot well while the
vehicle is moving. Objects can become trapped under the brake pedal and
accelerator pedal causing a loss of vehicle control.
• Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of
control of the vehicle.
• Never use the ‘PARK’ position as a substitute for the parking brake. Always
apply the parking brake fully when parked to guard against vehicle movement
and possible injury or damage.
• Refer to your Owner's Manual on the DVD for further details.
3
INTRODUCTION/WELCOME
Rollover Warning
4
INTRODUCTION/WELCOME
Use of Aftermarket Products (Electronics)
The use of aftermarket devices including cell phones, MP3 players, GPS systems, or
chargers may affect the performance of on-board wireless features including Keyless
Enter-N-Go™ and Remote Start range. If you are experiencing difficulties with any of
your wireless features, try disconnecting your aftermarket devices to see if the
situation improves. If your symptoms persist, please see an authorized dealer.
CHRYSLER, JEEP, MOPAR, ATF+4, COMMAND-TRAC, FREEDOM TOP, ROCK-TRAC,
RUBICON, SAHARA, TRU-LOK, Uconnect and WRANGLER are registered trademarks
of Chrysler Group LLC.
COPYRIGHT ©2012 CHRYSLER GROUP LLC
5
DRIVER COCKPIT
CONTROLS AT A GLANCE
6
H. Climate Controls pg. 24
B. Turn Signal/Lights Lever (behind
steering wheel) pg. 21
• Hill Descent
E. Wiper/Washer Lever (behind steering
wheel) pg. 22
• Hazard Switch
• Electronic Stability Control pg. 94
D. Instrument Cluster pg. 8
F. Power Windows
• Heated Seat Switches pg. 19
J. SWITCH PANEL
C. Electronic Vehicle Information Center
(EVIC) Display (behind steering
wheel) pg. 8
I. Power Outlet/Cigar Lighter pg. 85
G. Audio System (touch-screen-radio
shown) pg. 40
A. Electronic Vehicle Information Center
(EVIC) Controls pg. 82
Q. Power Door Locks
P. Tilt Steering Column Lever pg. 18
O. Ignition Switch
N. Electronic Speed Control pg. 23
M. Power Mirrors
L. Transfer Case Gear Selector
K. Transmission Gear Selector
CONTROLS AT A GLANCE
7
CONTROLS AT A GLANCE
INSTRUMENT CLUSTER
Warning Lights
- Low Fuel Warning Light
- Charging System Light**
- Oil Pressure Warning Light**
- Anti-Lock Brake (ABS) Light**
- Air Bag Warning Light**
- Electronic Throttle Control (ETC) Light
- Tire Pressure Monitoring System (TPMS) Light
- Engine Temperature Warning Light
- Seat Belt Reminder Light
BRAKE
- Brake Warning Light**
- Malfunction Indicator Light (MIL)**
- Electronic Stability Control (ESC) Activation/Malfunction Indicator
Light**
(See page 94 for more information.)
8
CONTROLS AT A GLANCE
Indicators
-
Turn Signal Indicators
High Beam Indicator
Front Fog Light Indicator
Front Axle Lock Indicator*
Rear Axle Lock Indicator*
Vehicle Security Indicator*
- O/D (Overdrive) Off Indicator
- 4WD Indicator*
- Sway Bar Indicator*
- Electronic Stability Control
(ESC) Off Indicator
- Cruise Indicator
Odometer Messages
ECO - Fuel Saver Indicator
door - Door Ajar
gASCAP - Fuel Cap Fault
gATE* - Swing Gate Ajar
noFUSE* - Fuse Fault
LoW tirE* - Low Tire Pressure
HOTOIL* - Transmission Temperature
Warning Message
CHAngE OIL* - Change Engine Oil
* If equipped
** Bulb Check with Key On
9
GETTING STARTED
KEY FOB
Locking And Unlocking The
Doors/Swing Gate
• Press the LOCK button once to lock all
the doors and swing gate. Press the
UNLOCK button once to unlock the
driver’s door only and twice within five
seconds to unlock all the doors and
swing gate.
• All doors can be programmed to unlock
on the first press of the UNLOCK button.
Refer to Programmable Features in this
guide.
Panic Alarm
• Press the PANIC button once to turn the panic alarm on.
• Wait approximately three seconds and press the button a second time to turn the
panic alarm off.
WARNING!
• Never leave children alone in a vehicle, or with access to an unlocked vehicle.
Allowing children to be in a vehicle unattended is dangerous for a number of
reasons. A child or others could be severely injured or killed. Children should
be warned not to touch the parking brake, brake pedal, or the shift lever. Do not
leave the Key Fob in or near the vehicle, or in a location accessible to children,
A child could start the vehicle, operate power windows, other controls, or move
the vehicle.
• Do not leave children or animals inside parked vehicles in hot weather. Interior
heat build-up may cause them to be severely injured or killed.
REMOTE START
• Press the REMOTE START button 2 on the Key Fob twice within five seconds.
Pressing the REMOTE START button a third time shuts the engine off.
x
• To drive the vehicle, press the UNLOCK button, insert the key in the ignition and
turn to the ON/RUN position.
• With remote start, the engine will only run for 15 minutes (timeout) unless the
ignition key is placed in the ON/RUN position.
• The vehicle must be started with the key after two consecutive timeouts.
10
GETTING STARTED
WARNING!
• Do not start or run an engine in a closed garage or confined area. Exhaust gas
contains Carbon Monoxide (CO) which is odorless and colorless. Carbon
Monoxide is poisonous and can cause you or others to be severely injured or
killed when inhaled.
• Keep Key Fob transmitters away from children. Operation of the Remote Start
System, windows, door locks or other controls could cause you and others to be
severely injured or killed.
THEFT ALARM
To Arm:
• Press the Key Fob LOCK button or the power door lock switch while the door is
open.
To Disarm:
• Press the Key Fob UNLOCK button or turn the ignition to the ON/RUN position.
SEAT BELT
• Be sure everyone in your vehicle is in a seat and using a seat belt properly.
• Position the lap belt across your thighs, below your abdomen. To remove slack in
the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too
tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of
sliding under the belt in a collision.
• Position the shoulder belt on your chest so that it is comfortable and not resting on
your neck. The retractor will withdraw any slack in the belt.
• A shoulder belt placed behind you will not protect you from injury during a
collision. You are more likely to hit your head in a collision if you do not wear your
shoulder belt. The lap and shoulder belt are meant to be used together.
• A belt that is too loose will not protect you properly. In a sudden stop you could move
too far forward, increasing the possibility of injury. Wear your seat belt snugly.
• A frayed or torn belt could rip apart in a collision and leave you with no protection.
Inspect the belt system periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do not disassemble or modify the
system. Seat belt assemblies must be replaced after a collision if they have been
damaged (bent retractor, torn webbing, etc.).
• The seat belts for both front seating positions are equipped with pretensioning
devices that are designed to remove slack from the seat belt in the event of a
collision.
• A deployed pretensioner or a deployed air bag must be replaced immediately.
11
GETTING STARTED
WARNING!
In a collision, you and your passengers can suffer much greater injuries if you are
not buckled up properly. You can strike the interior of your vehicle or other
passengers, or you can be thrown out of the vehicle. Always be sure you and others
in your vehicle are buckled up properly.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR
BAGS
• This vehicle has Advanced Front Air Bags for both the driver and right front
passenger as a supplement to the seat belt restraint system. The Advanced Front
Air Bags will not deploy in every type of collision.
• Advanced Front Air Bags are designed to provide additional protection by supplementing the seat belts in certain frontal collisions depending on several factors,
including the severity and type of collision. Advanced Front Air Bags are not expected
to reduce the risk of injury in rear, side, or rollover collisions.
• This vehicle may be equipped with Supplemental Seat-Mounted Side Air Bags to
provide enhanced protection to help protect an occupant during a side impact.
is not on during starting, stays on, or turns on while
• If the Air Bag Warning Light
driving, have the vehicle serviced by an authorized service center immediately.
• Refer to the Owner's Manual on the DVD for further details regarding the Supplemental Restraint System (SRS).
WARNING!
• Relying on the air bags alone could lead to more severe injuries in a collision.
The air bags work with your seat belt to restrain you properly. In some
collisions, the air bags won't deploy at all. Always wear your seat belts even
though you have air bags.
• Being too close to the steering wheel or instrument panel during Advanced
Front Air Bag deployment could cause serious injury, including death. Air bags
need room to inflate. Sit back, comfortably extending your arms to reach the
steering wheel or instrument panel.
• Supplemental Seat-Mounted Side Air Bags need room to inflate. Do not lean
against the door or window. Sit upright in the center of the seat.
• Being too close to the Seat-Mounted Side Air Bag during deployment could
cause you to be severely injured or killed.
• Do not drive your vehicle after the air bags have deployed. If you are involved
in another collision, the air bags will not be in place to protect you.
• After any collision, the vehicle should be taken to an authorized dealer
immediately.
12
GETTING STARTED
CHILD RESTRAINTS
• Children 12 years and under should ride properly buckled up in a rear seat, if
available. According to crash statistics, children are safer when properly restrained
in the rear seats rather than in the front.
• Every state in the United States and all Canadian provinces require that small
children ride in proper restraint systems. This is the law, and you can be prosecuted
for ignoring it.
NOTE:
For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK.
Canadian residents, should refer to Transport Canada’s website for additional information. http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-index-53.htm
Installing The LATCH - Compatible Child Restraint System
• Your vehicle's second row passenger seats are equipped with the child restraint
anchorage system called LATCH, which stands for Lower Anchors and Tether for
CHildren.
• Four-Door models: The rear outboard seating positions have lower anchors, and all
three rear seating positions have top tether anchors. Child seats with fixed lower
attachments must be installed in the outboard positions only. Child seats with flexible
lower attachments can be used in all three seating positions. Never install LATCHcompatible child seats such that two seats share a common lower anchorage.
• Two-door models can accommodate
flexible LATCH-compatible child seats
in the two outboard seating positions
only. Both rear seating positions have
lower anchors and top tether anchors.
Child seats with fixed or flexible
LATCH-compatible attachments can
be installed in either outboard seating
position.
• Loosen the child seat adjusters on the
lower straps and tether straps so that
you can attach the hook or connector
to the lower and tether anchorages
more easily.
• Attach the lower hooks or connectors
over the top of the anchorage bars,
pushing aside the seat cover material.
You will easily feel the anchorage bars
if you run your finger along the intersection of the seatback and seat cushion surfaces.
13
GETTING STARTED
• The tether strap should be attached to the tether anchor on the rear of the seatback
using the most direct path. For the outboard seating positions, route the tether
underneath the head rest and attach the hook to the tether anchor located on the
back of the seat.
• Tighten all three straps as you push the
child restraint rearward and downward
into the seat.
Installing The Child Restraint Using The Vehicle Seat Belts
• To install a child restraint, first, pull enough of the seat belt webbing from the
retractor to route it through the belt path of the child restraint and slide the latch
plate into the buckle.
• Next, extract all the seat belt webbing out of the retractor and then allow the belt
to retract into the retractor. Finally, pull on any excess webbing to tighten the lap
portion around the child restraint. Any seat belt system will loosen with time, so
check the belt occasionally, and pull it tight if necessary.
• Once you have completed securing the child restraint with the seat belt, secure the
top tether strap. The tether strap should be attached to the tether anchor on the
rear of the seatback using the most direct path. For the outboard seating positions,
route the tether underneath the head rest and attach the hook to the tether anchor
located on the back of the seat.
14
GETTING STARTED
WARNING!
• In a collision, an unrestrained child, even a tiny baby, can become a projectile
inside the vehicle. The force required to hold even an infant on your lap could
become so great that you could not hold the child, no matter how strong you
are. The child and others could be severely injured or killed. Any child riding in
your vehicle should be in a proper restraint for the child's size.
• Improper installation of a child restraint to the LATCH anchorages can lead to
failure of an infant or child restraint. The child could be severely injured or
killed. Follow the manufacturer’s directions exactly when installing an infant or
child restraint.
• An incorrectly anchored tether strap could lead to increased head motion and
possible injury to the child. Use only the anchor positions directly behind the
child seat to secure a child restraint top tether strap.
• Rearward-facing child seats must never be used in the front seat of a vehicle
with a front passenger air bag. An air bag deployment could cause severe injury
or death to infants in this position.
FRONT SEATS
MANUAL SEAT
Forward/Rearward
• Lift up on the adjusting bar located at
the front of the seat near the floor and
release at the desired position. Then,
using body pressure, move forward and
backward on the seat to be sure that
the seat adjusters have latched.
Height Adjustment
• Ratchet the front lever, located on the
outboard side of the seat, upward to
raise the seat height.
• Ratchet the lever downward to lower
the seat height.
Recliner
• Lift the recliner lever located on the
outboard side of the seat, lean back
and release at the desired position.
15
GETTING STARTED
Driver’s and Passenger Easy Entry Seats (Two-Door)
• Push the lever on the seatback rearward (toward the rear of the vehicle) to
tilt the entire seat forward.
• To return the seat to a sitting position,
rotate the seatback upright until it
locks. Push the seat rearward until the
track locks.
NOTE:
• If equipped with a combination lever, the seatback will return to its first locked
position. The recliner handle will have to be actuated to adjust the seatback to the
desired reclined position.
• The front passenger seats have a track memory which returns the seat to just past
the halfway point of the track, regardless of its original position.
• The recliner and easy entry levers should not be used during the automatic
returning of the seat to its fully upright position.
WARNING!
• Adjusting a seat while the vehicle is moving is dangerous. The sudden
movement of the seat could cause you to lose control. The seat belt might not
be properly adjusted, and you could be severely injured or killed. Only adjust a
seat while the vehicle is parked.
• Do not ride with the seatback reclined so that the seat belt is no longer resting
against your chest. In a collision, you could slide under the seat belt and be
severely injured or killed. Use the recliner only when the vehicle is parked.
16
GETTING STARTED
REAR SEATS
Folding Rear Seat
• Be sure that the front seats are fully upright and positioned forward. This will allow
the rear seat to fold down easily.
To Fold The Rear Seat
• Lift the seatback release lever and fold the seatback forward (two-door models).
• Slowly flip the entire seat (two-door
models) forward.
• Locate the pull strap, located on the
outboard side of the seat, and pull it
toward you until the seatback releases
(four-door models).
To Raise The Rear Seat
• Lift up on the seatback to return it to
the upright position.
WARNING!
• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
In a collision, people riding in these areas are more likely to be severely injured
or killed. Do not allow people to ride in any area of your vehicle that is not
equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat
and using a seat belt properly.
• Be certain that the seatback is securely locked into position. If the seatback is
not securely locked into position, the seat will not provide the proper stability
for child seats and/or passengers. An improperly latched seat could cause you
or others to be severely injured or killed.
17
GETTING STARTED
TILT STEERING COLUMN
• The tilt lever is located on the steering
column, below the turn signal lever.
• Push down on the lever to unlock the
steering column.
• With one hand firmly on the steering
wheel, move the steering column up or
down as desired.
• Pull upward on the lever to lock the
column firmly in place.
WARNING!
Do not adjust the steering column while driving. Adjusting the steering column
while driving, or driving with the steering column unlocked, could cause the driver
to lose control of the vehicle. Be sure the steering column is locked before driving
your vehicle. Failure to follow this warning may result in you or others being
severely injured or killed.
18
GETTING STARTED
HEATED SEATS
Front Heated Seats
• The controls for front heated seats are
located near the bottom center of the
instrument panel (below the heater/air
conditioning controls).
• Press the switch once to select Highlevel heating. Press the switch a second time to select Low-level heating.
Press the switch a third time to shut
the heating elements Off.
• If the High-level setting is selected, the
system will automatically switch to Lowlevel after approximately 30 minutes.
The Low-level setting will turn Off automatically after approximately 30 minutes.
WARNING!
• Persons who are unable to feel pain to the skin because of advanced age,
chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions must exercise care when using the seat heater.
It may cause burns even at low temperatures, especially if used for long periods
of time.
• Do not place anything on the seat that insulates against heat, such as a blanket
or cushion. This may cause the seat heater to overheat. Sitting in a seat that
has been overheated could cause serious burns due to the increased surface
temperature of the seat.
19
OPERATING YOUR VEHICLE
ENGINE BREAK-IN RECOMMENDATIONS
• A long break-in period is not required for the engine and drivetrain (transmission
and axle) in your vehicle.
• Drive moderately during the first 300 miles (500 km). After the initial 60 miles
(100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
• While cruising, brief full-throttle acceleration within the limits of local traffic laws
contributes to a good break-in. Wide-open throttle acceleration in low gear can be
detrimental and should be avoided.
• The engine oil installed in the engine at the factory is a high-quality energy
conserving type lubricant. Oil changes should be consistent with anticipated
climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “Maintaining Your Vehicle”.
NOTE:
A new engine may consume some oil during its first few thousand miles (kilometers)
of operation. This should be considered a normal part of the break-in and not
interpreted as an indication of difficulty.
CAUTION!
Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may
result.
20
OPERATING YOUR VEHICLE
TURN SIGNAL/LIGHTS LEVER
Headlights/Parking Lights/Automatic Headlights
• Rotate the end of the lever to the first detent for parking lights
, and the third detent for AUTO.
detent for headlights
, the second
• When set to AUTO, the system automatically turns the headlights on or off based
on ambient light levels.
Instrument Panel Dimmer
• Rotate the center portion of the lever to the extreme bottom position to fully dim
the instrument panel lights and prevent the interior lights from illuminating when
a door is opened.
• Rotate the center portion of the lever up to increase the brightness of the
instrument panel lights when the parking lights or headlights are on.
• Rotate the center portion of the lever upward to the next detent position to brighten
the odometer and radio controls when the parking lights or headlights are on.
• Rotate the center portion of the lever upward to the last detent to turn on the
interior lighting.
Flash To Pass
• Pull the lever toward you to activate the high beams. The high beams will remain
on until the lever is released.
High Beam Operation
• Push the lever forward to activate the high beams.
NOTE:
For safe driving, turn off the high beams when oncoming traffic is present to prevent
headlight glare and as a courtesy to other motorists.
21
OPERATING YOUR VEHICLE
Fog Lights
• Turn on the parking lights or low beam headlights and pull out the end of the lever.
Turn Signals/Lane Change Assist
• Tap the lever up or down once and the turn signal (right or left) will flash three
times and automatically turn off.
WIPER/WASHER LEVER
Front Wipers
Intermittent, Low And High Operation
• Rotate the end of the lever to the first detent position for one of five intermittent
settings, the second detent for low wiper operation and the third detent for high wiper
operation.
Washer Operation
• Pull the lever toward you and hold for as long as spray is desired.
Mist
• Pull down on the lever and release when a single wipe is desired.
NOTE:
The mist feature does not activate the washer pump; therefore, no washer fluid will be
sprayed on the windshield. The wash function must be activated in order to spray the
windshield with washer fluid.
Rear Wiper
Wiper Operation
• Rotate the center portion of the lever forward to the first detent for rear wiper operation.
Washer Operation
• Rotate the center portion of the lever past the first detent to activate the rear washer.
22
OPERATING YOUR VEHICLE
SPEED CONTROL
• The Electronic Speed Control switches
are located on the steering wheel.
Cruise ON/OFF
• Push the ON/OFF switch to activate the
Speed Control.
will appear on
• The cruise symbol
the instrument cluster to indicate the
Speed Control is on.
• Push the ON/OFF switch a second time
to turn the system off.
Set
• With the Speed Control on, push and
release the SET – button to set a desired
speed.
Accel/Decel
• Once a speed is set, pushing the RES + button once or the SET – button once will
increase or decrease the set speed approximately 1 mph (1.6 km/h).
• Push and hold the RES + button to accelerate in 5 mph (8 km/h) increments or
push and hold the SET – button to decelerate in 5 mph (8 km/h) increments;
release the button to save the new set speed.
Resume
• To resume a previously selected set speed in memory, push the RES + button and
release.
Cancel
• Push the CANCEL switch, or apply the brakes or clutch, to cancel the set speed
and maintain the set speed memory.
• Push the ON/OFF switch to turn the system off and erase the set speed memory.
23
OPERATING YOUR VEHICLE
MANUAL CLIMATE CONTROLS
Air Recirculation
• Use recirculation for maximum A/C operation.
• For window defogging, turn the recirculation button off.
• Recirculation is allowed in floor mode.
• Recirculation is allowed in defrost/floor (mix modes) for approximately five minutes.
Heated Mirrors
• The mirrors are heated to melt frost or ice. This feature is activated whenever you
turn on the rear window defroster.
24
OPERATING YOUR VEHICLE
AUTOMATIC TEMPERATURE CONTROLS (ATC)
Automatic Operation
• Turn the Mode and Blower Controls to the AUTO position.
• Select the desired temperature by rotating the Temperature Control.
• The system will maintain the set temperature automatically.
Air Conditioning (A/C)
• If the air conditioning button is pressed while in AUTO mode, the system will exit
AUTO mode and stay in A/C. The mode and blower will go to the previous user
setting.
Air Recirculation
• Use recirculation for maximum A/C operation.
• For window defogging, turn the air recirculation button off.
• If the recirculation button is pressed while in the AUTO mode, the indicator light
may flash three times to indicate the cabin air is being controlled automatically.
Heated Mirrors
• The mirrors are heated to melt frost or ice. This feature is activated whenever you
turn on the rear window defroster.
25
OPERATING YOUR VEHICLE
SUNRIDER® AND SOFT TOP
2–Door Sunrider® Down
• Follow these simple steps to open the Sunrider® feature.
1. Unclip and move the sun visors to the side.
2. Release the header latches from the loops on the windshield frame.
3. Slide the plastic sleeve forward.
26
OPERATING YOUR VEHICLE
4. Grasp the header and lift the top back. Make sure the material is folded back as
shown.
5. Locate the straps to secure the side
bows. Wrap the straps around the bows
as shown. Repeat on the other side.
6. Reposition the sun visors.
NOTE:
If you are going to be driving faster than
40 mph (64 km/h) with the Sunrider®
feature open, it is recommended that you
remove the rear window of the vehicle.
• To close the Sunrider® feature, perform
the above steps in the opposite order.
27
OPERATING YOUR VEHICLE
2–Door Soft Top Down
• Follow these simple steps to lower the 2–door soft top.
1. Remove the side and back windows.
2. Remove rear corner panels.
3. Release header latches from the windshield frame.
28
OPERATING YOUR VEHICLE
4. Release the Sunrider® latch (both sides).
5. Open the swing gate and lower the top.
NOTE:
Ensure the fabric does not overhang the
sides of the vehicle.
• To raise the soft top, perform the above
steps in the opposite order.
29
OPERATING YOUR VEHICLE
4–Door Sunrider® Down
• Follow these simple steps to open the Sunrider® feature.
1. Unclip and move the sun visors to the side.
2. Release the header latches from the loops on the windshield frame.
3. Grasp the front side bow behind the header, and lift the top.
30
OPERATING YOUR VEHICLE
4. Fold the top so that the material forms a "W" as shown. Enter the vehicle and move
the material into two folds.
5. Fold back the front section of the top
and gently rest the header on top of
the rear portion of the deck.
6. Secure the top by using the two provided straps. Each strap will wrap
around the side bow and Velcro® to
itself; use one strap on each side of
the vehicle.
NOTE:
• Failure to fold the fabric rearward will
allow the material to sag and may
block the rearview mirror.
• If you are going to be driving faster
than 40 mph (64 km/h) with the
Sunrider® feature open, it is recommended that you remove the rear
window of the vehicle.
• To close the Sunrider® feature, perform the above steps in the opposite
order.
31
OPERATING YOUR VEHICLE
4–Door Soft Top Down
• Follow these simple steps to lower the 4–door soft top.
1. Remove the side and back windows.
2. Remove rear corner panels.
3. Release header latches from the windshield frame.
32
OPERATING YOUR VEHICLE
4. Fold header rearward, pulling the fabric to the rear.
5. Fold the top so that the material forms a "W" as shown. Enter the vehicle and move
the material into two folds.
6. Release Sunrider® latch (both sides).
33
OPERATING YOUR VEHICLE
7. Open the swing gate and lower the top.
NOTE:
Ensure the fabric does not overhang the
sides of the vehicle.
• To raise the soft top, perform the above
steps in the opposite order.
CAUTION!
• Do not run a fabric top through an automatic car wash. Window scratches and
wax buildup may result.
• Do not lower the top when the temperature is below 41°F (5°C). Damage to the
top may result.
• Do not lower the top when the windows are dirty. Grit may scratch the window.
• Do not move your vehicle until the top has been either fully attached to the
windshield frame, or fully lowered.
• The soft top is not designed to carry any additional loads such as roof racks,
spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also,
it was not designed as a structural member of the vehicle and, thus, cannot
properly carry any additional loads other than environmental (rain, snow, etc.).
WARNING!
• Do not drive the vehicle with the rear window curtain up unless the side
curtains are also open. Dangerous exhaust gases which can kill could enter the
vehicle.
• The fabric upper doors and fabric top are designed only for protection against
the elements. Do not rely on them to contain occupants within the vehicle or to
protect against injury during an accident. Remember, always wear seat belts.
34
OPERATING YOUR VEHICLE
HARD TOP AND FREEDOM TOP®
Freedom Top® Removal
• Follow these simple steps to remove the front panels.
1. Fold down the sun visor, and move it to the side.
2. Turn the rear fasteners (knobs) (located on the overhead speaker bar assembly)
counterclockwise until they can be removed.
3. Turn the center L-shaped locks (two)
from the center of the roof panel.
35
OPERATING YOUR VEHICLE
4. Turn the rear L-shaped lock (located above the shoulder belt anchorage).
5. Unlatch the header panel latch located at the top of the windshield.
6. Remove the left-hand panel.
• To remove the right panel, follow the
steps above except for Step 3.
NOTE:
• The left panel must be removed before
removing right panel.
• Vehicles equipped with a Freedom
Top®, come with a Freedom Top® storage bag that allows you to store your
Freedom Top® panels. Refer to the
Owner's Manual on the DVD for details.
Hard Top Removal
• Follow these simple steps to remove the hard top.
1. Remove both front panels. Refer to “Front Panel(s) Removal” above.
2. Open both doors.
3. Remove the two Torx® head screws that secure the hard top at the B-pillar (near
the top of the door) using a #40 Torx® head driver (Four–Door Only).
4. Remove the six Torx® head screws that secure the hard top to the vehicle (along
the interior bodyside) using a #40 Torx® head driver.
5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift
the rear window glass.
36
OPERATING YOUR VEHICLE
6. Locate and disconnect the wire harness on the left rear inside corner of the
vehicle.
7. Remove the washer hose (next to the
wire harness) by pinching the grips on
hose connector and pull downward.
8. Close the swing gate.
9. Remove the hard top from the vehicle.
Place the hard top on a soft surface to
prevent damage.
CAUTION!
• The front panel(s) must be positioned properly to ensure sealing. Improper
installation can cause water to leak into the vehicles interior.
• The hard top assembly must be positioned properly to ensure sealing. Improper
installation can cause water to leak into the vehicles interior.
• The hard top is not designed to carry any additional loads such as roof racks,
spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also,
it was not designed as a structural member of the vehicle, and thus cannot
properly carry any additional loads other than environmental (rain, snow, etc.).
• Do not move your vehicle until the top has been either fully attached to the
windshield frame and bodyside, or fully removed.
• The removal of the hard top requires four adults located on each corner. Failure
to follow this caution could damage the hard top.
37
OPERATING YOUR VEHICLE
DUAL TOP — IF EQUIPPED
• If your vehicle is equipped with a Dual Top, you must remove one of the tops from
the vehicle.
• 2 Door - If the soft top is removed, the pivot brackets must also be removed from
the sport bar.
• 4 Door - If the soft top is removed, ensure that the pivot bracket strap is installed onto
the Soft Top pivot bracket before removing the soft top from the vehicle. Remove the
fasteners between the Soft Top pivot bracket and the attach bracket to the sport
bar.
• The soft top was installed at the factory
for shipping purposes only.
NOTE:
The soft top and the hard top are to be
used independently.
• Refer to the Understanding The Features Of Your Vehicle section of your
vehicle's Owner's Manual on the DVD
for further details.
38
OPERATING YOUR VEHICLE
WIND BUFFETING
• Wind buffeting can be described as a helicopter-type percussion sound. If
buffeting occurs with the rear windows open, adjust the front and rear windows
together.
39
ELECTRONICS
YOUR VEHICLE'S SOUND SYSTEM
40
ELECTRONICS
41
ELECTRONICS
Uconnect® 130
NOTE:
Your radio has many features that add to the comfort and convenience of you and your
passengers. Some of these radio features should not be used when driving because
they take your eyes from the road or your attention from driving.
Clock Setting
• Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL”
control knob to set the hours.
• Press the “TUNE/SCROLL” control knob until the minutes begin to blink; turn the
“TUNE/SCROLL” control knob to set the minutes.
• Press the “TUNE/SCROLL” control knob to save the time change.
• To exit, press any button/knob or wait five seconds.
Equalizer, Balance And Fade
• Press the “TUNE/SCROLL” control knob and BASS, MID, TREBLE, BALANCE and
FADE will display. Rotate the “TUNE/SCROLL” control knob to select the desired
setting.
42
ELECTRONICS
Radio Operation
Seek Up/Down Buttons
• Press to seek through radio stations in AM or FM bands.
• Hold either button to bypass stations without stopping.
Store Radio Presets
• Press the “SET/RND” button once and SET 1 will show in the display. Then select
button (1–6).
• A second station may be added to each push button. Press the “SET/RND” button
twice and SET 2 will show in the display. Then select button (1–6).
CD/DISC Operation
Seek Up/Down Buttons
• Press to seek through CD tracks.
• Hold either button to bypass tracks without stopping.
SET/RND Button (Random Play)
• Press this button while the CD is playing to activate Random Play.
• This feature plays the selections on the CD in random order to provide an
interesting change of pace.
Audio Jack Operation
• The Audio Jack allows a portable device, such as an MP3 player or an iPod®, to be
plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio
cable, to amplify the source and play through the vehicle speakers.
• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack
is connected, allowing the music from your portable device to play through the
vehicle's speakers.
• The functions of the portable device are controlled using the device buttons, not
the buttons on the radio. The volume may be controlled using the radio or portable
device.
43
ELECTRONICS
Uconnect® 130 WITH SiriusXM™ SATELLITE RADIO
NOTE:
• Your radio may not be equipped with the Uconnect® Voice Command and
Uconnect® Phone features. To determine if your radio has these features, press the
Voice Command button on the radio. You will hear a voice prompt if you have the
feature, or see a message on the radio stating “Uconnect Phone not available” if
you do not.
• Your radio has many features that add to the comfort and convenience of you and
your passengers. Some of these radio features should not be used when driving
because they take your eyes from the road or your attention from driving.
Clock Setting
• Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL”
control knob to set the hours.
• Press the “TUNE/SCROLL” control knob until the minutes begin to blink; turn the
“TUNE/SCROLL” control knob to set the minutes.
• Press the “TUNE/SCROLL” control knob to save the time change.
• To exit, press any button/knob or wait five seconds.
Equalizer, Balance And Fade
• Press the “TUNE/SCROLL” control knob and BASS, MID, TREBLE, BALANCE and
FADE will display. Rotate the “TUNE/SCROLL” control knob to select the desired
setting.
44
ELECTRONICS
Radio Operation
Seek Up/Down Buttons
• Press to seek through radio stations in AM, FM, or SAT bands.
• Hold either button to bypass stations without stopping.
Store Radio Presets
• Press the “SET/RND” button once and SET 1 will show in the display. Then select
button (1–6).
• A second station may be added to each push button. Press the “SET/RND” button
twice and SET 2 will show in the display. Then select button (1–6).
Music Type
• Press the “MUSIC TYPE” button to activate this mode. Press the “MUSIC TYPE”
button again or turn the “TUNE/SCROLL” control knob to select the desired music
type (Adult Hits, Country, Jazz, Oldies, Rock, etc.).
• Once a music type is chosen and the icon is displayed, press either “SEEK” button
and the radio will only search for stations with the selected music type.
NOTE:
The Music Type function only operates when in FM mode.
SETUP Button
• Pressing the “SETUP” button allows you to select between items that are available
in that particular mode.
• Turn the “TUNE/SCROLL” control knob to scroll through the entries. Push the
“AUDIO/SELECT” button to select an entry and make changes.
SiriusXM™ Satellite Radio
• SiriusXM™ Satellite Radio gives you over 130 channels, including 100%
commercial-free music from nearly every genre, plus all your favorite sports, news,
talk and entertainment channels–all with crystal clear, coast-to-coast coverage, all
in one place and all at your fingertips.
• To access SiriusXM™ Satellite Radio, press the “SAT” hard-key.
CD/DISC Operation
Seek Up/Down Buttons
• Press to seek through CD tracks.
• Hold either button to bypass tracks without stopping.
SET/RND Button (Random Play)
• Press this button while the CD is playing to activate Random Play.
• This feature plays the selections on the CD in random order to provide an interesting
change of pace.
45
ELECTRONICS
LIST Button
• Press the “LIST” button to bring up a list of all folders on the CD. Scroll up or down
the list by turning the “TUNE/SCROLL” control knob.
• To select a folder from the list, press the “TUNE/SCROLL” control knob and the
radio will begin playing the files contained in that folder.
Audio Jack Operation
• The Audio Jack allows a portable device, such as an MP3 player or an iPod®, to be
plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio
cable, to amplify the source and play through the vehicle speakers.
• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack
is connected, allowing the music from your portable device to play through the
vehicle's speakers.
• The functions of the portable device are controlled using the device buttons, not
the buttons on the radio. The volume may be controlled using the radio or portable
device.
46
ELECTRONICS
Uconnect® 230
NOTE:
• Your radio may not be equipped with the Uconnect® Voice Command and
Uconnect® Phone features. To determine if your radio has these features, press the
Voice Command button on the radio. You will hear a voice prompt if you have the
feature, or see a message on the radio stating “Uconnect Phone not available” if
you do not.
• Your radio has many features that add to the comfort and convenience of you and
your passengers. Some of these radio features should not be used when driving
because they take your eyes from the road or your attention from driving.
Clock Setting
• Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL”
control knob to set the hours.
• Press the “TUNE/SCROLL” control knob until the minutes begin to blink; turn the
“TUNE/SCROLL” control knob to set the minutes.
• Press the “TUNE/SCROLL” control knob to save the time change.
• To exit, press any button/knob or wait five seconds.
Equalizer, Balance And Fade
• Press the “TUNE/SCROLL” control knob and BASS, MID, TREBLE, BALANCE and
FADE will display. Rotate the “TUNE/SCROLL” control knob to select the desired
setting.
47
ELECTRONICS
Radio Operation
Seek Up/Down Buttons
• Press to seek through radio stations in AM, FM, or SAT bands.
• Hold either button to bypass stations without stopping.
Store Radio Presets
• Press the “SET” button once and SET 1 will show in the display. Then select
button (1–6).
• A second station may be added to each push button. Press the “SET” button twice
and SET 2 will show in the display. Then select button (1–6).
Music Type
• Press the “MUSIC TYPE” button to activate this mode. Press the “MUSIC TYPE”
button again or turn the “TUNE/SCROLL” control knob to select the desired music
type (Adult Hits, Country, Jazz, Oldies, Rock, etc.).
• Once a music type is chosen and the icon is displayed, press the SEEK button and
the radio will only search for stations with the selected music type.
NOTE:
The Music Type function only operates when in FM mode.
SETUP Button
• Pressing the “SETUP” button allows you to select between items that are available
in that particular mode.
• Turn the “TUNE/SCROLL” control knob to scroll through the entries. Push the
“AUDIO/SELECT” button to select an entry and make changes.
SiriusXM™ Satellite Radio
• SiriusXM™ Satellite Radio gives you over 130 channels, including 100%
commercial-free music from nearly every genre, plus all your favorite sports, news,
talk and entertainment channels–all with crystal clear, coast-to-coast coverage, all
in one place and all at your fingertips.
• To access SiriusXM™ Satellite Radio, press the “SAT” hard-key.
CD/DISC Operation
Seek Up/Down Buttons
• Press to seek through CD tracks.
• Hold either button to bypass tracks without stopping.
LIST Button
• Press the “LIST” button to bring up a list of all folders on the CD. Scroll up or down
the list by turning the “TUNE/SCROLL” control knob.
• To select a folder from the list, press the “TUNE/SCROLL” control knob and the
radio will begin playing the files contained in that folder.
48
ELECTRONICS
How To Load Multiple CDs/DVDs
• Press the “LOAD” button and then press the button with the corresponding
number (1–6) where the CD is being loaded. The radio will display PLEASE WAIT
and prompt when to INSERT DISC.
• After the radio displays INSERT DISC, insert the CD into the player. The radio
display will show LOADING DISC when the disc is loading and “READING DISC”
when the radio is reading the disc.
• Press the eject button and then the corresponding number (1–6) to eject the
desired disc.
Audio Jack Operation
• The Audio Jack allows a portable device, such as an MP3 player or an iPod®, to be
plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio
cable, to amplify the source and play through the vehicle speakers.
• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack
is connected, allowing the music from your portable device to play through the
vehicle's speakers.
• The functions of the portable device are controlled using the device buttons, not
the buttons on the radio. The volume may be controlled using the radio or portable
device.
49
ELECTRONICS
Uconnect® 430/430N
NOTE:
• Your radio may not be equipped with the Uconnect® Voice Command and
Uconnect® Phone features. To determine if your radio has these features, press the
Voice Command button on the radio. You will hear a voice prompt if you have the
feature, or see a message on the radio stating “Uconnect Phone not available” if
you do not.
• Your radio has many features that add to the comfort and convenience of you and
your passengers. Some of these radio features should not be used when driving
because they take your eyes from the road or your attention from driving.
Clock Setting
• Turn the radio on, then touch the screen where the time is displayed.
• Touch the “USER CLOCK” soft-key (Navigation radio only).
• To adjust the hours, touch either the “HOUR FORWARD” or “HOUR BACKWARD”
soft-key.
• To adjust the minutes, touch either the “MINUTE FORWARD” or “MINUTE
BACKWARD” soft-key.
• To save the new time setting, touch the screen where the word “Save” is displayed.
50
ELECTRONICS
Menu
• Press the “MENU” hard-key to access the System Setup menu and the My Files
menu.
• Press the “MENU” hard-key in an active mode (SAT, CD, AUX, etc.) in order to
change mode specific settings.
Equalizer, Balance And Fade
Audio Control Menu
• Press the “AUDIO” hard-key on the
right side of the radio.
• Use either the arrow soft-keys or the
cross-hair on the screen to change
Balance and Fade. The “CENTER”
soft-key resets the settings.
• Touch the “Equalizer” soft-key and use either the arrow soft-keys or the sliders on
the screen to adjust BASS, MID, and/or TREBLE.
Display Settings
• Press the “MENU” hard-key and touch
the “Display Settings” soft-key to access the Display Settings menu.
• Select the “Daytime Colors” soft-key to
switch to manual daytime mode and to
adjust the brightness of the display
using daytime colors.
• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to
adjust the brightness of the display using nighttime colors.
• Select the “Auto Color Mode” soft-key to switch to automatic daytime/nighttime
mode and to control the brightness of the display using the dimmer switch of the
vehicle.
• Touch the “EXIT” soft-key to save your settings.
51
ELECTRONICS
Radio Operation
• To access Radio Mode, touch the “RADIO” hard-key on the left side of the
faceplate, then touch the “AM,” “FM” or “SAT” soft-key at the top of the screen
to select the band.
Seek Up/Seek Down
• Press the “Seek Up” or “Seek Down” soft-keys to seek through radio stations in
AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.
Store Radio Presets
• Select the radio band by touching either the “AM,” “FM,” or “SAT” soft-key.
• Find the station to store by either pressing the “Seek Up” or “Seek Down”
soft-keys, touching the “SCAN” soft-key, or by using the “DIRECT TUNE” soft-key.
• Once the station is found, touch and hold one of the “PRESET” soft-keys in the list
to the right, until you hear a confirmation beep.
NOTE:
If the Presets are not visible on the right side of the screen, press the “Presets”
soft-key.
52
ELECTRONICS
CD/DVD Disc Operation
• Press the “MEDIA” hard key to display the media source tabs at the top of the
screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source
soft-key tab.
NOTE:
Your Touch-Screen Radio will usually automatically switch to the appropriate mode
when something is first connected or inserted into the system.
Insert a CD/DVD Disc
• To insert a disc, press the “LOAD” hard-key.
• With the printed side upwards, insert the disc into the disc slot of the radio. The
radio pulls the disc in automatically and closes the flip screen. The radio selects
the appropriate mode after the disc is recognized, and starts playing the first track.
The display shows “Reading...” during this process.
Seek Up/Seek Down
• Press the “Seek Up” or “Seek Down” soft-keys to seek through tracks in Disc
Mode. Hold either Seek to bypass tracks without stopping.
53
ELECTRONICS
Audio Jack Operation
• The Audio Jack allows a portable device, such as an MP3 player or an iPod®, to be
plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio
cable, to amplify the source and play through the vehicle speakers.
• Pressing the “MEDIA” hard-key and then the “AUX” soft-key to change the mode
to auxiliary device if the Audio Jack is connected, allowing the music from your
portable device to play through the vehicle's speakers.
• The functions of the portable device are controlled using the device itself, not the
buttons on the radio. The volume may be controlled using the radio or portable
device.
Hard Disk Drive (HDD) Operation
• The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal
hard disk drive. It functions similar to a CD player, with the exception that the
internal HDD can hold more tracks.
• It is also possible to import display pictures to the internal hard disk drive. The
pictures can be displayed on the right half of the radio screen.
• Before using the HDD mode, you will need to copy songs and pictures to the
internal hard drive. Songs and pictures can be added to the hard drive by using a
CD or USB device (e.g. thumb drive or memory stick).
NOTE:
HDD supports only .jpg/JPEG formats for photos.
NOTE:
WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See
the Uconnect® 430/430N User's Manual for more information.
Copying Music From CD
• Press the “LOAD” hard-key.
• Insert a disc, then press the “MY FILES” hard-key and then select “MY MUSIC
soft-key.”
• Touch the “Add Music Files to HDD” soft-key, then touch the “Disc” soft-key in the
next screen to start the process.
NOTE:
• You might need to select the folder or
title depending on the CD, then press
“DONE” to start the copy process.
• The copy progress is shown in the lower
left corner of the screen.
54
ELECTRONICS
Copying Music From USB
• The USB port on the radio face plate allows you to copy files to your hard drive. To
access, lift up on the cover.
• Insert a USB device (e.g. thumb drive or memory stick), then select “MY MUSIC
soft-key.”
• Touch the “Add Music Files to HDD” soft-key, then touch the “Front USB” soft-key
in the next screen.
• Select the folders or titles you would
like to copy, then touch the “DONE”
soft-key to start the copy process.
NOTE:
The copy progress is shown in the lower
left corner of the screen.
Copying Pictures To The HDD
• Insert either a CD or a USB device
containing your pictures in JPEG format.
• Press the “MY FILES” hard-key.
• Touch the “My Pictures” soft-key to get an overview of the currently stored images,
then touch the “Add” soft-key.
• Touch the “Disc” or “USB” soft-key, then select the folders or pictures you wish to
copy to the HDD. Use the “PAGE” soft-keys to page through the list of pictures.
• Touch the desired pictures or press the “All” soft-key for all pictures. Confirm your
selections by touching the “SAVE” soft key.
NOTE:
The copy progress is shown in the lower
left corner of the screen.
Display A Picture On The Radio Screen
• Once the import is complete, the pictures will then be available in the “MY
PICTURES” screen.
• Press the “MY FILES” hard-key, then touch the “My Pictures” soft-key. Touch the
desired picture, then touch the “Set as Picture View” soft-key and then touch the
“Exit” soft-key. Lastly press the “MENU” hard-key and then touch the “Picture
View” soft-key to display the chosen picture on the radio screen.
NOTE:
• A check mark in the My Pictures screen indicates the currently used picture.
• You can also delete pictures by touching the “Delete” soft-key.
55
ELECTRONICS
Playing Music From The HDD
• Press the “MEDIA” hard key to display the media source tabs at the top of the
screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or
touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by
genre, from a folder, or from Favorites.
Cleaning Your Touch-Screen Radio
• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean
and dry micro fiber lens cleaning cloth in order to clean the touch-screen.
• If necessary, use a lint-free cloth dampened with a cleaning solution such as
isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Be sure
to follow the solvent manufacturer's precautions and directions.
Garmin® Navigation
• Uconnect® 430N integrates Garmin’s consumer-friendly navigation into your
vehicle. Garmin® Navigation includes a database with over 6 million points of
interest.
• Touch the “NAV” soft-key in the upper right corner of the screen to access the
Navigation system.
56
ELECTRONICS
Changing the Navigation Voice Prompt Volume
1. Program a destination.
2. While traveling on your route, touch the upper left area of the map screen where
your next turn is displayed.
3. The Navigation system will then repeat the distance to your next turn.
4. While the Navigation system is speaking, use the ON/OFF VOLUME rotary knob to
adjust the volume to a comfortable level. Please note the volume setting for
Navigation Voice Prompt is different than the audio system.
NOTE:
For your own safety and the safety of others, it is not possible to use certain features
while the vehicle is in motion.
Main Navigation Menu
Finding Points Of Interest
• From the main Navigation menu, touch “Where To?,” then touch “Points of Interest.”
• Select a Category and then a subcategory, if necessary.
• Select your destination and touch “Go.”
Finding A Place By Spelling The Name
• From the Main Navigation Menu, touch
“Where to?,” then touch “Points of
Interest” and then touch “Spell Name.”
• Enter the name of your destination.
• Touch “Done.”
• Select your destination and touch “Go.”
Entering A Destination Address
• From the main Navigation menu, touch “Where To?,” then touch “Address.”
• Follow the on-screen prompts to enter the address and touch “Go.”
Searching Near Another Location
• From the main Navigation menu, touch “Where To?,” then touch a destination and
then touch “Near.”
• Select an option from the available choices.
57
ELECTRONICS
Setting Your Home Location
• From the main Navigation menu, touch “Where To?,” then touch “Go Home.”
• You may enter your address directly, use your current location as your home
address, or choose from recently found locations.
Edit Home Location
• From the main Navigation menu, touch “Where To?,” then touch “Favorites.”
• Next, touch the location you would like to edit, then touch “Press for More,” and
then “Edit.”
Go Home
• A Home location must be saved in the system. From the Main Navigation menu,
touch “Where To?,” then touch “Go Home.”
Following Your Route
• Your route is marked with a magenta line on the map. If you depart from the
original route, your route is recalculated. A speed limit icon could appear as you
travel on major roadways.
Adding A Via Point
• To add a stop between the current location and the end destination (Via Point) you
must be navigating a route.
• Touch the “back arrow icon” multiple times to return to the Main Navigation menu.
58
ELECTRONICS
• Touch “Where To?,” then search for the additional stop. Then select the Via Point
you wish to add from the given search results.
• Touch “Go,” then touch “Add to Current Route.”
Taking A Detour
• To take a detour you must be navigating a route.
• Touch the “back arrow icon” multiple times to return to the Main Navigation menu.
• Touch “Detour.”
NOTE:
If the route you are currently taking is the only reasonable option, the device might
not calculate a detour.
Acquiring Satellites
• The GPS Satellite strength bars indicate the strength of your satellite reception.
• Acquiring satellite signals can take a few minutes. When at least one of the bars is
green, your device has acquired satellite signals.
• You may experience delays in acquisition of satellite signals when in areas with an
obstructed view to the sky, such as garages, tunnels, or large cities with tall
buildings.
59
ELECTRONICS
Uconnect® 730N
NOTE:
Your radio has many features that add to the comfort and convenience of you and
your passengers. Some of these radio features should not be used when driving
because they take your eyes from the road or your attention from driving.
Clock Setting
• Turn the radio on, then touch the screen where the time is displayed.
• Touch the “USER CLOCK” soft-key.
• To adjust the hours, touch either the “HOUR FORWARD” or “HOUR BACKWARD”
soft-key.
• To adjust the minutes, touch either the “MINUTE FORWARD” or “MINUTE
BACKWARD” soft-key.
• To save the new time setting, touch the screen where the word “Save” is displayed.
Menu
• Press the “MENU” hard-key to access the System Setup menu and the My Files
menu.
• Press the “MENU” hard-key in an active mode (SAT, CD, AUX, etc.) in order to
change mode specific settings.
60
ELECTRONICS
Equalizer, Balance And Fade
Audio Control Menu
• Press the “MENU” hard-key on the
right side of the radio. Then press the
“Audio Control” soft-key to get to the
audio control menu.
• Use either the arrow soft-keys or the
cross-hair on the screen to change Balance and Fade. The “CENTER” softkey resets the settings.
• Touch the “Equalizer” soft-key and use either the arrow soft-keys or the sliders on
the screen to adjust BASS, MID, and/or TREBLE.
Display Settings
• Press the “MENU” hard-key and touch
the Display Settings soft-key to access
the Display Settings menu.
• Select the “Daytime Colors” soft-key to
switch to manual daytime mode and to
adjust the brightness of the display
using daytime colors.
• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to
adjust the brightness of the display using nighttime colors.
• Select the “Auto Color Mode” soft-key to switch to automatic daytime/ nighttime
mode and to control the brightness of the display using the dimmer switch of the
vehicle.
• Touch the “EXIT” soft-key to save your settings.
61
ELECTRONICS
Radio Operation
• To access Radio Mode, touch the “RADIO/MEDIA” hard-key on the left side of the
faceplate repeatedly until AM/FM/SAT appears at the top of the screen, then touch
the “AM,” “FM” or “SAT” soft-key to select the band.
Seek Up/Seek Down
• Press the “Seek Up” or “Seek Down” hard-keys to seek through radio stations in
AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.
Store Radio Presets
• Select the radio band by touching either the “AM,” “FM,” or “SAT” soft-key.
• Find the station to store by either pressing the “Seek Up” or “Seek Down” hard-keys,
touching the “SCAN” soft-key, or by using the “DIRECT TUNE” soft-key.
• Once the station is found, touch and hold one of the PRESET soft-keys in the list
to the right, until you hear a confirmation beep.
NOTE:
If the Presets are not visible on the right side of the screen, press the “Presets”
soft-key.
62
ELECTRONICS
CD/DVD Disc Operation
• Press the “RADIO/MEDIA” hard key until the media source tabs are displayed at
the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX”
media source soft-key tab.
NOTE:
Your Touch-Screen Radio will usually automatically switch to the appropriate mode
when something is first connected or inserted into the system.
Insert a CD/DVD Disc
• To insert a disc, press the “OPEN/CLOSE” hard-key.
• With the printed side upwards, insert the disc into the disc slot of the radio. The
radio pulls the disc in automatically and closes the flip screen. The radio selects
the appropriate mode after the disc is recognized, and starts playing the first track.
The display shows “Reading...” during this process.
Seek Up/Seek Down
• Press the “Seek Up” or “Seek Down” hard-keys to seek through tracks in Disc Mode.
Hold either Seek to bypass tracks without stopping.
Audio Jack Operation
• The Audio Jack allows a portable device, such as an MP3 player or an iPod®, to be
plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio
cable, to amplify the source and play through the vehicle speakers.
63
ELECTRONICS
• Pressing the “RADIO/MEDIA” hard-key and then the “AUX” soft-key to change the
mode to auxiliary device if the Audio Jack is connected, allowing the music from
your portable device to play through the vehicle's speakers.
• The functions of the portable device are controlled using the device itself, not the
buttons on the radio. The volume may be controlled using the radio or portable
device.
Hard Disk Drive (HDD) Operation
• The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal
hard disk drive. It functions similar to a CD player, with the exception that the
internal HDD can hold more tracks.
• It is also possible to import display pictures to the internal hard disk drive. The
pictures can be displayed on the right half of the radio screen.
• Before using the HDD mode, you will need to copy songs and pictures to the
internal hard drive. Songs and pictures can be added to the hard drive by using a
CD or USB device (e.g. thumb drive or memory stick).
NOTE:
HDD supports only .jpg/JPEG formats for photos.
NOTE:
WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See
the Uconnect® 730N User's Manual for more information.
Copying Music From CD
• Press the “OPEN/CLOSE” hard-key.
• Insert a disc, then press the “MENU” hard-key.
• Touch the “MY FILES” soft-key, then select “MY MUSIC.”
• Touch the “Add Music Files to HDD”
soft-key, then touch the “From Disc”
soft-key in the next screen to start the
process.
NOTE:
• You might need to select the folder or
title depending on the CD, then press
“Done” to start the copy process.
• The copy progress is shown in the lower
left corner of the screen.
64
ELECTRONICS
Copying Music From USB
• The USB port on the radio face plate allows you to copy files to your hard drive.
To access, lift up on the cover.
• Insert a USB device (e.g. thumb drive or memory stick), then select “MY FILES”.
• Touch the “MY MUSIC” soft-key, then touch the “Add Music Files” to HDD soft-key.
• Touch “From USB” soft-key, then select
the folders or titles you would like to
copy, and then touch the “SAVE” softkey to start the copy process.
NOTE:
The copy progress is shown in the lower
left corner of the screen.
Copying Pictures To The HDD
• Insert either a CD or a USB device containing your pictures in JPEG format.
• Press the “MENU” hard-key to access the Settings Menu, then touch the “My Files”
soft-key.
• Touch the “My Pictures” soft-key to get an overview of the currently stored images,
then touch the “Add” soft-key.
• Touch the “From Disc” or “From USB”
soft-key, then select the folders or pictures you wish to copy to the HDD. Use
the “PAGE” soft-keys to page through
the list of pictures.
• Touch the desired pictures or press the
“All” soft-key for all pictures. Confirm
your selections by touching the “SAVE”
soft key.
NOTE:
The copy progress is shown in the lower left corner of the screen.
65
ELECTRONICS
Display A Picture On The Radio Screen
• Once the import is complete, the pictures will then be available in the “MY
PICTURES” screen.
• Press the “MENU” hard-key to access the Settings Menu, then touch the “My Files”
soft-key and then touch the “My Pictures” soft-key. Touch the desired picture, then
touch the “Set as Picture View” soft-key and then touch the “Exit” soft-key. Lastly
press the “MENU” hard-key and then touch the “Picture View” soft-key to display the
chosen picture on the radio screen.
NOTE:
• A check mark in the My Pictures screen indicates the currently used picture.
• You can also delete pictures by touching the “Delete” soft-key.
Playing Music From The HDD
• Press the “RADIO/MEDIA” hard key until the media source tabs are displayed at
the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track
soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by
album, by song, by genre, from a folder, or from Favorites.
Cleaning Your Touch-Screen Radio
• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean
and dry micro fiber lens cleaning cloth in order to clean the touch-screen.
• If necessary, use a lint-free cloth dampened with a cleaning solution such as
isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Be sure
to follow the solvent manufacturer's precautions and directions.
66
ELECTRONICS
NAVIGATION
• Your navigation system receives GPS
signals from up to 16 satellites to display the position of your vehicle. Map
and database information is supplied
through a hard disk drive.
• Touch the “NAV” hard-key on the radio
face plate to access the Navigation
system and the NAV – Main Menu.
Changing the Navigation Guidance Prompt Volume
1. From the Navigation Map screen, touch the Menu hard-key and then touch the
Guidance Prompts soft-key
2. Select and adjust the navigation guidance prompt volume using the left and right
arrows.
3. Touch the SAMPLE VOL soft-key to
listen to the current volume setting.
4. Once satisfied with the volume, touch
the SAVE soft-key to save the settings.
Touch the CANCEL soft-key to exit the
menu without saving the settings.
NOTE:
For your own safety and the safety of others, it is not possible to use the certain
features while the vehicle is in motion.
67
ELECTRONICS
Main Navigation Menu
Finding Points Of Interest
• From the NAV main menu, touch the “Points of Interest” soft-key.
• Select a Category and then a subcategory, if necessary.
• Select your destination and touch “GO.”
Finding A Place By Entering The Street Address
• From the NAV main menu, touch “New Destination,” then touch “Street Address.”
NOTE:
If the wrong State and/or Country displayed are incorrect, touch the corresponding
soft-key to make the correction.
• Once the Country and State are set and the Street Address screen is displayed,
begin spelling the street name in the speller. In the upper right corner the number
of possible roads decreases.
• Touch the “LIST” soft-key to display a list of possible street names. Select the
correct street name.
• Next input the number.
• In the Confirm Route screen the navigation radio displays the complete address,
a map of the destination area, and the current routing method for you to verify.
• Touch the “GO” soft-key to activate the route guidance.
68
ELECTRONICS
Entering Your Home Location
• Press the “NAV” hard-key on the right side of the radio.
• From the Nav – Main Menu, touch “Guide Me Home” to enter your home address.
If no home address has been set, touch “YES” to access the Enter Home Address
menu.
• Touch “Street Address” to enter your address. Touch the soft-key with your state’s
name and enter your street name into the speller.
• Once the street name has been input, touch “CONTINUE” to confirm. Enter the
house number into the next screen. If more than one city has this address, you will
then need to select your city from a list.
• Once the address is entered completely, the system shows a map of your home
address area. Touch “SAVE” to confirm the address. The system will then ask if you
want to go there, yes or no.
Change Home Address
• This procedure will allow you to change your Home Address if one has already been
entered.
• Press the “MENU” hard-key, touch “My Files” and then touch “My Address Book.”
• Touch “Home,” then touch “Edit Contacts” and then “Change Address.”
• Touch the soft-key with your state’s name and enter your street name into the
speller.
• Once the street name has been input, touch “CONTINUE” to confirm.
• Enter the house number into the next screen. If more than one city has this
address, you will then need to select your city from a list.
• Touch the “SAVE” soft-key to confirm the address.
Go Home
• From the NAV main menu, touch “Guide Me Home” when you want to route to your
home destination.
Where Am I Now?
• From the NAV main menu, touch “Where Am I Now?.” The Where Am I Now? menu
displays location information for the current vehicle position.
• Touch the “NEARBY POI”soft-key to search for a local Point of Interest.
• Touch the “SAVE LOCATION” soft-key to save the current location in the Saved
Locations memory.
69
ELECTRONICS
Route Guidance
• After starting route guidance, the system calculates the route and announces:
“Follow the arrows on the display.” You will receive navigation recommendations
by voice messages and screen displays.
Route Options
• After pressing the “OPTIONS” soft-key in the Route Guidance Menu, the following
information is displayed:
• In the left half of the screen, the current position and the current routing method
are displayed.
• “Take Detour” will allow you to calculate a different route.
• “Find Nearby POI” to search for a local POI.
• “Destination Info” displays destination information.
• “View Turn List” lists streets utilized for the current route.
• “Save Destination” to save the destination address.
• “Change Method” will allow you to change the routing method.
70
ELECTRONICS
SiriusXM™ SATELLITE RADIO/TRAVEL LINK
• SiriusXM™ Travel Link requires a subscription, sold separately after the 1 year trial
subscription included with your vehicle purchase.
• SiriusXM™ Travel Link is only available in the United States.
• The following describes features that are available when in SiriusXM™ Satellite
Radio mode.
• To access SiriusXM™ Satellite Radio, press the “RADIO/MEDIA” or “RADIO” and
then touch the “SAT” soft-key tab.
Info
• Touch the “i” soft-key to view detailed information about the current Sirius XM™
Satellite channel.
SiriusXM™ Parental Controls
• SiriusXM™ offers the option to permanently block selected channels. Call
1-888-539-7474 and request the Family Package.
• Uconnect® 430/430N and 730N: Press the “MENU” hard-key while in SiriusXM™
Satellite Radio Mode, then touch the “Channel Lock” to enable and/or disable
desired channels. The SEEK and SCAN function will then only display channels
without Channel lock.
Search/Browse
• Touch the “magnifying glass” soft-key to search/browse the SiriusXM™ channel
listing by Favorites and Categories such as Song, Artist and Channel Name. The
Search/Browse also allows you manage your Favorites.
SiriusXM™ Satellite Radio Favorites (SAT Favorites)
• You can save 50 favorite songs and 50 favorite artists.
• Touch the “add favorite” soft-key to
add either the song or the artist of the
currently playing program to the SAT
Favorites list. The favorite star will
appear in the upper right corner, below
the SAT soft key.
71
ELECTRONICS
• You will see a favorite star indicator in the upper right side of the screen below the
SAT soft-key and a pop up will alert you that a favorite song or artist is currently
playing on one of the SiriusXM™ satellite radio channels.
NOTE:
Refer to your Uconnect® 730N or 430/
430N User's Manual for more information.
Display SAT Favorites List
• Touch the “Search/Browse” soft-key and select “Favorites” from the SAT Browse
screen.
• Touch the desired favorites soft-key to
switch the SAT tuner to the corresponding channel.
• You may use the “LIST” soft-key to
toggle between:
Favorite Songs.
Favorite Artists.
Currently playing favorites.
Replay
• While you are in SAT mode, you can
replay 44 minutes of the current
SiriusXM™ channel (when the channel is changed, this audio buffer is
erased). Press the REPLAY button to
listen to the stored audio.
• You can touch the on-screen controls
to pause and rewind audio playback,
touch the SCAN button to preview
each of the tracks stored in the buffer,
or select a track from the list.
72
ELECTRONICS
• The time displayed below the bar indicates how much time is present between the
current buffer play position and the live broadcast.
Replay Option
Play/Pause
Option Description
Touch to Pause content playback. Touch Pause/Play again to resume
playback.
Rewind/RW
Rewinds the channel content in steps of 5 seconds. Touch and hold
to rewind continuously, then release to begin playing content at that
point.
Fast Forward/FW Forwards the content, and works similarly to Rewind/RW. However,
Fast Forward/FW can only be used when content has been previously
rewound.
Replay Time
Displays the amount of time in the upper center of the screen by
which your content lags the Live channel.
Live
Resumes playback of Live content at any time while replaying
rewound content.
73
ELECTRONICS
SiriusXM™ Travel Link (Uconnect® 730N & Uconnect® 430N Only)
NOTE:
• SiriusXM™ Travel Link requires a subscription, sold separately after the 1 year trial
subscription included with your vehicle purchase.
• SiriusXM™ Travel Link is only available in the United States.
• SiriusXM™ Travel Link brings a wealth of useful information into your vehicle and
right to your fingertips.
• To access Travel Link, press the MENU hard-key, then the Travel Link soft-key.
1 – Favorites
2 – Forecast
3 – Ski Info
4 – Fuel Prices
5 – Movies
6 – Sports
74
View and store your favorite location, theater and sport teams for quick
access.
View detailed weather conditions, forecasts and ski/snowboarding
conditions at resorts.
View ski and snowboarding conditions at ski resorts.
View detailed price information for fuel stations.
View information on movies that are playing at theaters.
View sports scores and upcoming events for all major sports.
ELECTRONICS
STEERING WHEEL AUDIO CONTROLS
• The steering wheel audio controls are
located on the rear surface of the steering wheel.
Right Switch
• Press the switch up or down to increase
or decrease the volume.
• Press the button in the center to
change modes AM/FM/CD/SAT.
Left Switch
• Press the switch up or down to search
for the next listenable station or select
the next or previous CD track.
• Press the button in the center to select
the next preset station (radio) or to
change CDs if equipped with a CD Changer.
iPod®/USB/MP3 CONTROL
• There are many ways to play music from iPod®/MP3 players or USB devices
through your vehicle's sound system.
• The remote USB port, located within the center console, allows you to plug an
iPod® into the vehicle's sound system.
NOTE:
If equipped with the Uconnect® 730N, the USB port on the faceplate allows the
same functions as the remote USB port.
• Non-Touch-Screen Radios: To hear audio from devices connected to the USB port,
press the “AUX” button on the radio face plate
• Touch-Screen Radios: To hear audio from devices connected to the USB port, press
the “MEDIA” hard-key, then touch the “AUX” or “iPod®” soft-key.
• When connected to this feature:
• The iPod® can be controlled using
the radio buttons to Play, Browse,
and List the iPod® or external devices
contents.
• The iPod® battery charges when
plugged into the USB port (if supported by the specific audio device).
• Compatible iPod® devices may also
be controllable using voice commands. Refer to the Owner's Manual
on the DVD for details.
75
ELECTRONICS
NOTE:
The USB port supports certain Mini, Classic, Nano, Touch, and iPhone® devices. The
USB port also supports playing music from compatible external USB Mass Storage
Class memory devices. For supported audio file formats, refer to the USB Port section
in the Owner's Manual on the DVD. Refer to www.UconnectPhone.com website for a
list of tested iPod®s. Some iPod® software versions may not fully support the USB
port features. Please visit Apple’s website for iPod® software updates.
WARNING!
Do not plug in or remove the iPod® or external device while driving. Failure to
follow this warning could result in a collision.
Uconnect® Phone
• To determine if your vehicle is equipped with Uconnect® Phone, press the
. If your vehicle has this feature, you will hear a
“Uconnect® Phone” button
voice prompt. If not, you will see a message on the radio “Uconnect phone not
available”.
• The Uconnect® Phone is a voice-activated, hands-free, in-vehicle communications
system with Voice Command Capability (see Voice Command section).
NOTE:
To access the tutorial, press the “Uconnect® Phone” button
. After the BEEP,
say “tutorial.” Press any hard-key/button or touch the display (Touch-Screen radio) to
cancel the “tutorial”.
• The Uconnect® Phone allows you to dial a phone number with your mobile phone
using simple voice commands.
• Refer to your vehicle Owner's Manual on the DVD for further details.
NOTE:
The Uconnect® Phone requires a mobile phone equipped with the Bluetooth®
Hands-Free Profile, Version 1.0 or higher. For Uconnect® customer support, call
1–877–855–8400 or visit www.UconnectPhone.com. This site will provide specific
instructions based on the type of mobile phone being paired.
Phone Pairing
NOTE:
• Pairing is a one-time initial setup before using the phone.
• Prior to starting the pairing procedure ensure all additional phones within the
vehicle have their Bluetooth® disabled.
• The Uconnect® Phone requires a mobile phone equipped with the Bluetooth®
Hands-Free Profile, Version 1.0 or higher. For Uconnect® customer support, call
1–877–855–8400 or visit www.UconnectPhone.com. This site will provide specific instructions based on the type of mobile phone being paired.
76
ELECTRONICS
• Press the “Phone”
button to begin.
• Wait for the “ready” prompt and BEEP.
• (After the BEEP), say ”setup” or “Uconnect device setup”.
• (After the BEEP), say “device pairing”.
• (After the BEEP), say “pair a device”.
• Follow the audible prompts.
• You will be asked to say a four-digit
Personal Identification Number (PIN),
which you will later need to enter into
your mobile phone. You can say any
four-digit PIN. You will not need to
remember this PIN after the initial pairing process.
• You will then be prompted to give the phone pairing a name (each phone paired
should have a unique name).
• Next you will be asked to give this new pairing a priority of 1 thru 7 (up to seven
phones may be paired); 1 is the highest and 7 is the lowest priority. The system will
only connect to the highest priority phone that exists within the proximity of the
vehicle.
• You will then need to start the pairing procedure on your cell phone. Follow the
Bluetooth® instructions in your cell phone Owner's Manual to complete the phone
pairing setup.
Phonebook
Phonebook Download – Automatic Phonebook Transfer From Mobile Phone
If equipped and specifically supported by your phone, Uconnect® Phone automatically
downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this
feature. Automatic Transfer is indicated by a green arrow at the bottom of the screen.
See www.UconnectPhone.com for supported phones.
• Automatic download and update, if
supported, begins as soon as the
Bluetooth® wireless phone connection
is made to the Uconnect® Phone, for
example, after you start the vehicle.
77
ELECTRONICS
NOTE:
The mobile phone may require authorization prior to download.
• A maximum of 1000 entries per phone will be downloaded and updated every time
a phone is connected to the Uconnect® Phone.
• Depending on the maximum number of entries downloaded, there may be a short
delay before the latest downloaded names can be used. Until then, if available, the
previously downloaded phonebook is available for use.
• Only the phonebook of the currently connected mobile phone is accessible.
• Only the mobile phone’s phonebook is downloaded. The SIM card phonebook is not
part of the Mobile phonebook.
• This downloaded phonebook cannot be edited or deleted on the Uconnect® Phone.
These can only be edited on the mobile phone. The changes are transferred and
updated to Uconnect® Phone on the next phone connection.
Making A Phone Call
• Press the “Phone” button
.
• (After the BEEP), say “dial” (or “call” a name).
• (After the BEEP), say number (or name).
Receiving A Call – Accept (And End)
• When an incoming call rings/is announced on Uconnect®, press the Phone button
.
• To end a call, press the Phone button
.
Mute (Or Unmute) Microphone During Call
• During a call, press the “Voice Command” button
.
• (After the BEEP), say “mute” (or “mute off”).
Transfer Ongoing Call Between Handset And Vehicle
• During a call, press the “Voice Command” button
.
• (After the BEEP), say “transfer call”.
Changing The Volume
• Start a dialogue by pressing the “Phone” button
during a normal call.
, then adjust the volume
• Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable
level while the Uconnect® system is speaking. Please note the volume setting for
Uconnect® is different than the audio system.
78
ELECTRONICS
WARNING!
• Any voice commanded system should be used only in safe driving conditions
following applicable laws regarding phone use. Your attention should be
focused on the safely operating the vehicle. Failure to do so may result in a
collision causing you and others to be severely injured or killed.
• In an emergency, to use Uconnect® Phone, your mobile phone must be:
• turned on,
• paired to Uconnect® Phone,
• and have network coverage.
Uconnect® VOICE COMMAND
Voice Command Operation
• The Uconnect® Voice Command system allows you to control your AM, FM radio,
satellite radio, disc player, HDD, Uconnect® Phone, a memo recorder, and
supported portable media devices.
located on the radio
• When you press the “Voice Command” button
faceplate or steering wheel, you will hear a beep. The beep is your signal to give a
command. If you do not say a command within a few seconds, the system will
present you with a list of options. If you ever wish to interrupt the system while it
, listen for the BEEP, and
lists options, press the “Voice Command” button
say your command.
NOTE:
Visit http://www.driveuconnect.com/features/voiceCommand/ for more info on which
voice command features apply to your vehicle
• Start a dialogue by pressing the “Voice Command” button
, you will hear
a beep. The beep is your signal to give a command. Below are a list of voice
commands for each of the different modes.
79
ELECTRONICS
Common Voice Commands (Examples)
Main Menu
Radio Mode
SiriusXM™ Satellite
Radio Mode
Disc Mode
80
“Radio AM” (to switch to the AM radio mode)
“Radio FM” (to switch to the FM radio mode)
“Satellite Radio” (to switch to the Satellite radio mode)
“Disc” (to switch to the disc mode)
“USB” (to switch to the USB mode)
“Bluetooth Streaming” (to switch to the Bluetooth Streaming
mode)
“Memo” (to switch to the memo recorder)
“System Setup” (to switch to system setup)
“Frequency” (to change the frequency)
“Next Station” (to select the next station)
“Previous Station” (to select the previous station)
“Radio Menu” (to switch to the radio menu)
“Main Menu” (to switch to the main menu)
“Channel Number” (to change the channel by its spoken
number)
“Next Channel” (to select the next channel)
“Previous Channel” (to select the previous channel)
“List Channel” (to hear a list of available channels)
"Channel Name" (to change the channel by its spoken name)
“Select Name” (to say the name of a channel)
“Radio Menu” (to switch to the radio menu)
“Main Menu” (to switch to the main menu)
“Track” (#) (to change the track)
“Next Track” (to play the next track)
“Previous Track” (to play the previous track)
“Main Menu” (to switch to the main menu)
ELECTRONICS
Memo Mode
To switch to the voice recorder mode, say “Memo”. The
following are common voice commands for this mode: “New
Memo” (to record a new memo) — During the recording,
to stop
you may press the Voice Command button
recording. You proceed by saying one of the following commands:
— “Save” (to save the memo)
— “Continue” (to continue recording)
— “Delete” (to delete the recording)
— “Play Memos” (to play previously recorded memos) —
During the playback you may press the Voice Command
button
to stop playing memos. You proceed by
saying one of the following commands:
— “Repeat” (to repeat a memo)
— “Next” (to play the next memo)
— “Previous” (to play the previous memo)
— “Delete” (to delete a memo)
— “Delete All” (to delete all memos)
Voice Text Reply
• If equipped with Uconnect® Voice Command, your Uconnect® 430N & Uconnect®
730N radios may be able to play incoming Short Message Service (SMS) messages
(text messages) through the vehicle's sound system.
• It also allows you to respond by selecting from various pre-defined phrases.
• Not all phones are compatible with this feature. Refer to the phone compatibility
list at Visit Uconnect® Online. Connected mobile phones must be bluetoothcompatible, and paired with your radio.
• Press the “Voice Command” button
started.
and after the BEEP, say “SMS” to get
NOTE:
To access the tutorial, press the “Voice Command” button
. After the BEEP,
say “tutorial”. Press any hard-key/button or touch the display (Touch-Screen radio) to
cancel the tutorial.
WARNING!
Any voice commanded system should be used only in safe driving conditions
following applicable laws regarding phone use. Your attention should focused on
the safely operating the vehicle. Failure to do so may result in a collision causing
you and others to be severely injured or killed.
81
ELECTRONICS
Bluetooth® STREAMING AUDIO
• If equipped with Uconnect® Voice Command, your Bluetooth-equipped iPod®
devices, cell phones or other media
players, may also be able to stream
music to your vehicle's speakers. Your
connected device must be Bluetoothcompatible, and paired with your radio
(see Uconnect® Phone for pairing instructions). Non-Touch-Screen Radios:
Press the “AUX” button on the radio
faceplate until "BT" or “Audio Streaming” is displayed on the radio screen.
Touch-Screen-Radios: Press the “RADIO/MEDIA” or “MEDIA” hard-key and then
touch the “AUX” soft-key tab.
ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC)
• The EVIC features a driver interactive
display that is located in the instrument cluster. Pressing the controls on
the steering wheel allows the driver
to select vehicle information and Personal Settings. For additional information, refer to Programmable Features
in this guide.
• Press and release the MENU button to
scroll through the main menus (Fuel
Economy, Warnings, Timer, Units, System, Personal Settings) or to exit sub
menus.
• Press and release the SELECT button for access to main menus, sub menus or
to select a personal setting in the setup menu.
button to display one of eight compass readings
• Press and release the COMPASS
and the outside temperature or to exit sub menus.
• Press and release the DOWN
button to scroll downward through the sub menus.
Compass Calibration
• This compass is self-calibrating, which eliminates the need to set the compass
manually. When the vehicle is new, the compass may appear erratic and the EVIC
will display “CAL” until the compass is calibrated.
• You may also calibrate the compass by completing one or more 360 degree turns
(in an area free from large metal or metallic objects) until the “CAL” message
displayed in the EVIC turns off. The compass will now function normally.
82
ELECTRONICS
ECO
• The ECO message will appear in your EVIC display whenever you are driving in a
fuel efficient manner.
• This feature allows you to monitor when you are driving in a fuel efficient manner,
and it can be used to modify driving habits in order to increase fuel economy.
PROGRAMMABLE FEATURES
Electronic Vehicle Information Center (EVIC)
• The EVIC can be used to program the following Personal Settings. Press and
until Personal Settings displays, then press the
release the MENU button
to scroll through the settings. Press the SELECT button
to
DOWN button
change the setting.
•
•
•
•
•
•
•
•
Language
Auto UNLK On Exit
RKE Unlock
Sound Horn With RKE Lock
Flash Lamp With Lock
Headlamp Off Delay
Headlamps With Wipers
Key-Off Power Delay
•
•
•
•
•
•
•
Illumin Approach
Hill Start Assist (HSA)
Display Units of Measure In
Nav – Turn by Turn
Display Fuel Saver
Compass Variance
Calibrate Compass
Key Fob Programmable Features
• The following features may also be programmed by using the Key Fob transmitter
or the ignition switch and driver's door lock switch.
NOTE:
Pressing the LOCK button while you are inside the vehicle will activate the Vehicle
Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause
the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security
Alarm.
Flashing Lamps With Lock
• The turn signal lights flashing, when the doors are locked or unlocked, feature can
be turned on or off. To turn this feature on or off:
• Press and hold the UNLOCK button for at least 4 seconds, but no longer than
10 seconds. Then, press and hold the LOCK button while still holding the
UNLOCK button.
• Release both buttons at the same time.
83
ELECTRONICS
POWER INVERTER
• A 115 Volt, 150 Watt AC power inverter
is located on the front of the center
console.
• This outlet can power cellular phones,
electronics and other low power devices requiring power up to 150 Watts.
• The power inverter switch is located on
the instrument panel below the climate
controls. To turn on the power outlet,
press the switch once. The indicator
light will illuminate. Press the switch a
second time to turn the power inverter
outlet off.
NOTE:
The power inverter is designed with built-in overload protection. If the power rating
of 150 Watts is exceeded, the power inverter will automatically shut down. Once the
electrical device has been removed from the outlet, the inverter should automatically
reset. If the power rating exceeds approximately 170 Watts, the power inverter may
have to be reset manually. To reset the inverter manually, unplug the device and plug
it in again. To avoid overloading the circuit, check the power ratings on electrical
devices prior to using the inverter.
WARNING!
To Avoid Serious Injury or Death DO NOT:
• insert any objects into the receptacles
• touch with wet hands
Close the lid when not in use. If this outlet is mishandled, it may cause an electric
shock and failure.
84
ELECTRONICS
POWER OUTLETS
• There are three possible 12–Volt Power Outlets in this vehicle.
• The front power outlet, located in the lower portion of the instrument panel, is
powered when the key is in the ON or ACC position.
• A second power outlet is located inside the center console bin and is powered
directly from the vehicle battery.
• On vehicles equipped with a rear subwoofer, there is a power outlet located in the
right rear cargo area.
NOTE:
• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the
160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will
need to be replaced.
• Power outlets are designed for accessory plugs only. Do not insert any other object
in the power outlet as this will damage the outlet and blow the fuse. Improper use
of the power outlet can cause damage not covered by your new vehicle warranty.
85
OFF-ROAD CAPABILITIES
COMMAND-TRAC®/ROCK-TRAC®
• The transfer case provides four mode
positions: 2H (Two-wheel drive high
range), 4H (Four-wheel drive high
range), N (Neutral), and 4L (Fourwheel drive low range).
• The transfer case is intended to be
driven in the 2H position for normal
street and highway conditions such as
hard-surfaced roads.
• Shifting between 2H and 4H can be
made with the vehicle stopped or in
motion. Shift the transfer case lever
firmly to 4H at any speed up to 50 mph
(80 km/h).
• Shifting between 4H and 4L can be made with the vehicle rolling at 2 to 3 mph
(3 to 5 km/h). Shift the automatic transmission into NEUTRAL or fully depress the
clutch pedal on a manual transmission. Shift the transfer case lever firmly to 4L
(do not pause with the transfer case in NEUTRAL). Once the shift is completed,
place the automatic transmission into DRIVE or release the clutch pedal on a
manual transmission.
NOTE:
To enhance off-road performance in 4L mode, manual transmission vehicles will start
regardless of whether or not the clutch pedal is depressed.
86
OFF-ROAD CAPABILITIES
AXLE LOCK (TRU-LOK®) RUBICON ONLY
• The AXLE LOCK switch is located on the instrument panel (to the left of the
steering column).
• This feature will only activate when the following conditions are met:
• Key in Run Position, vehicle in 4L (Low) range.
• Vehicle speed at 10 mph (16 km/h) or less.
• Press the bottom of the AXLE LOCK switch once to lock the rear axle only and a
second time to lock the front axle (the rear and front axle lock indicator lights will
illuminate).
• To unlock the axles, press the top of the AXLE LOCK switch.
• The indicator light will flash until the axles are fully locked or unlocked.
ELECTRONIC SWAY BAR DISCONNECT – RUBICON
ONLY
Off-Road
• This feature will only activate when the following conditions are met:
• Key in Run positon, vehicle in 4L (Low) or 4H (High) range.
• Vehicle speed under 18 mph.
• Press the SWAY BAR switch, located on the instrument panel (to the left of the
steering column), once to disconnect the Sway Bar.
• The Sway Bar indicator light will illuminate in the instrument cluster.
On-Road
• Press the SWAY BAR switch a second time to reconnect the Sway Bar.
• The Sway Bar should remain in on-road mode during normal driving conditions.
87
88
Axle
3.21
3.73
3.21
3.73
3.21
3.73
3.21
3.73
4.10
3.73
4.10
3.21
Engine/
Transmission
3.6L/Manual
3.6L/Manual
3.6L/Automatic
3.6L/Automatic
3.6L/Manual
3.6L/Manual
3.6L/Automatic
3.6L/Automatic
3.6L/Manual
3.6L/Automatic
3.6L/Automatic
3.6L/Manual
GCWR (Gross Combined Wt. Rating)
6,296 lbs
(2 856 kg)
6,296 lbs
(2 856 kg)
6,309 lbs
(2 862 kg)
6,309 lbs
(2 862 kg)
6,355 lbs
(2 883 kg)
6,355 lbs
(2 883 kg)
6,368 lbs
(2 888 kg)
6,368 lbs
(2 888 kg)
6,445 lbs
(2 923 kg)
6,458 lbs
(2 929 kg)
6,458 lbs
(2 929 kg)
6,552 lbs
(2 972 kg)
Model
Two–Door Sport
Model (4WD)
Two–Door Sport
Model (4WD)
Two–Door Sport
Model (4WD)
Two–Door Sport
Model (4WD)
Two–Door Sahara
Model (4WD)
Two–Door Sahara
Model (4WD)
Two–Door Sahara
Model (4WD)
Two–Door Sahara
Model (4WD)
2–Door Rubicon
Model (4WD)
Two–Door Rubicon
Model (4WD)
Two–Door Rubicon
Model (4WD)
Four–Door Sport
Model (4WD)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
25 sq ft
(2.32 sq m)
32 sq ft
(2.97 sq m)
Frontal Area
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
2,000 lbs
(907 kg)
Max. GTW
(Gross Trailer Wt.)
TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
200 lbs (91 kg)
Max. Trailer
Tongue Wt.
(See Note)
UTILITY
Axle
Model
GCWR (Gross Combined Wt. Rating)
Frontal Area
Max. GTW
(Gross Trailer Wt.)
Max. Trailer
Tongue Wt.
(See Note)
3.6L/Manual
3.73
Four–Door Sport
8,052 lbs
32 sq ft
3,500 lbs
350 lbs (159 kg)
Model (4WD)
(3 652 kg)
(2.97 sq m)
(1 587 kg)
Four–Door Sport
6,566 lbs
32 sq ft
2,000 lbs
3.6L/Automatic
3.21
200 lbs (91 kg)
Model (4WD)
(2 978 kg)
(2.97 sq m)
(907 kg)
Four–Door Sport
8,066 lbs
32 sq ft
3,500 lbs
3.6L/Automatic
3.73
350 lbs (159 kg)
Model (4WD)
(3 659 kg)
(2.97 sq m)
(1 587 kg)
Four–Door Sahara
6,768 lbs
32 sq ft
2,000 lbs
3.6L/Manual
3.21
200 lbs (91 kg)
Model (4WD)
(3 070 kg)
(2.97 sq m)
(907 kg)
Four–Door Sahara
8,268 lbs
32 sq ft
3,500 lbs
3.6L/Manual
3.73
350 lbs (159 kg)
Model (4WD)
(3 750 kg)
(2.97 sq m)
(1 587 kg)
Four–Door Sahara
6,782 lbs
32 sq ft
2,000 lbs
3.6L/Automatic
3.21
200 lbs (91 kg)
Model (4WD)
(3 076 kg)
(2.97 sq m)
(907 kg)
Four–Door Sahara
8,282 lbs
32 sq ft
3,500 lbs
3.6L/Automatic
3.73
350 lbs (159 kg)
Model (4WD)
(3 757 kg)
(2.97 sq m)
(1 587 kg)
Four–Door Rubicon
8,334 lbs
32 sq ft
3,500 lbs
3.6L/Manual
4.10
350 lbs (159 kg)
Model (4WD)
(3 780 kg)
(2.97 sq m)
(1 587 kg)
Four–Door Rubicon
8,347 lbs
32 sq ft
3,500 lbs
3.6L/Automatic
4.10
350 lbs (159 kg)
Model (4WD)
(3 786 kg)
(2.97 sq m)
(1 587 kg)
Refer to local laws for maximum trailer towing speeds.
NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie. the GVWR), and the GVWR
should never exceed the weight referenced on the Tire and Loading Information placard.
Engine/
Transmission
UTILITY
89
90
On Trailer
Front
Rear
ALL
NONE
Flat Tow
Dolly Tow
Wheels OFF the Ground
Towing Condition
Towing This Vehicle Behind Another Vehicle
•
•
•
•
Four-Wheel Drive Models
See Instructions
Manual transmission in gear (NOT in NEUTRAL (N)
Transfer case in NEUTRAL (N)
Tow in forward direction
NOT ALLOWED
NOT ALLOWED
OK
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)
UTILITY
UTILITY
Recreational Towing – Four-Wheel Drive Models
NOTE:
The transfer case must be shifted into NEUTRAL (N), automatic transmission must
be shifted into PARK, and manual transmission must be placed in gear (NOT in
NEUTRAL) for recreational towing.
Shifting Into NEUTRAL (N)
Use the following procedure to prepare your vehicle for recreational towing.
1. Bring the vehicle to a complete stop.
2. Press and hold the brake pedal.
3. Shift the automatic transmission into NEUTRAL or depress the clutch pedal on a
manual transmission.
4. Turn OFF the engine.
5. Shift the transfer case lever into NEUTRAL (N).
6. Start the engine.
7. Shift the transmission into REVERSE.
8. Release the brake pedal (and clutch pedal on manual transmissions) for five
seconds and ensure that there is no vehicle movement.
9. Repeat steps 7 and 8 with automatic transmission in DRIVE or manual transmission in first gear.
10. Turn OFF the engine.
11. Firmly apply the parking brake.
12. Shift the transmission into PARK or place manual transmission in gear (NOT in
Neutral).
13. Attach the vehicle to the tow vehicle using a suitable tow bar.
14. Release the parking brake.
Shifting Out of NEUTRAL (N)
Use the following procedure to prepare your vehicle for normal usage.
1. Bring the vehicle to a complete stop, leaving it connected to the tow vehicle.
2. Firmly apply the parking brake.
3. Turn the ignition switch to the LOCK/OFF position.
4. Turn the ignition switch to the ON/RUN position, but do not start the engine.
5. Press and hold the brake pedal.
6. Shift the transmission into NEUTRAL.
91
UTILITY
7. Shift the transfer case lever to the desired position.
NOTE:
When shifting out of transfer case NEUTRAL (N), turning the engine OFF may be
required to avoid gear clash.
8. Shift the automatic transmission into PARK, or place manual transmission in
Neutral.
9. Release the brake pedal.
10. Disconnect vehicle from the tow vehicle.
11. Start the engine.
12. Press and hold the brake pedal.
13. Release the parking brake.
14. Shift the transmission into gear, release the brake pedal (and clutch pedal on
manual transmissions), and check that the vehicle operates normally.
CAUTION!
• It is necessary to follow these steps to be certain that the transfer case is fully in
NEUTRAL (N) before recreational towing to prevent damage to internal parts.
• Damage to the transmission may occur if the transmission is shifted into PARK
with the transfer case in NEUTRAL (N) and the engine running. With the
transfer case in NEUTRAL (N) ensure that the engine is OFF prior to shifting
the transmission into PARK.
• Front or rear wheel lifts should not be used. Internal damage to the transmission
or transfer case will occur if a front or rear wheel lift is used when recreational
towing.
• Tow only in the forward direction. Towing this vehicle backwards can cause
severe damage to the transfer case.
• Automatic transmissions must be placed in the PARK position for recreational
towing.
• Manual transmissions must be placed in gear (not in Neutral) for recreational
towing.
• Before recreational towing, perform the procedure outlined under “Shifting Into
NEUTRAL (N)” to be certain that the transfer case is fully in NEUTRAL (N).
Otherwise, internal damage will result.
• Towing this vehicle in violation of the above requirements can cause severe
transmission and/or transfer case damage. Damage from improper towing is
not covered under the New Vehicle Limited Warranty.
• Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper
face bar will be damaged.
92
UTILITY
WARNING!
You or others could be injured if you leave the vehicle unattended with the transfer
case in the N (NEUTRAL) position without first fully engaging the parking brake.
The transfer case N (NEUTRAL) position disengages both the front and rear
driveshafts from the powertrain and will allow the vehicle to move, even if the
transmission is in PARK. The parking brake should always be applied when the
driver is not in the vehicle.
93
WHAT TO DO IN EMERGENCIES
ROADSIDE ASSISTANCE
• Dial toll-free 1-800-521-2779 for U.S. Residents or 1-800-363-4869 for Canadian
Residents.
• Provide your name, vehicle identification number, license plate number, and your
location, including the telephone number from which you are calling.
• Briefly describe the nature of the problem and answer a few simple questions.
• You will be given the name of the service provider and an estimated time of arrival.
If you feel you are in an “unsafe situation”, please let us know. With your consent,
we will contact local police or safety authorities.
INSTRUMENT CLUSTER WARNING LIGHTS
- Electronic Stability Control (ESC) Activation/Malfunction Indicator Light
• If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the
engine running, a malfunction has been detected in the ESC system. If this light
remains on after several ignition cycles, and the vehicle has been driven several miles
(kilometers) at speeds greater than 30 mph (48 km/h), we recommend you drive to
the nearest service center and have the vehicle serviced immediately.
• The “ESC Activation/Malfunction Indicator Light” starts to flash as soon as the
tires lose traction and the ESC system becomes active. If the light begins to flash
during acceleration, ease up on the accelerator and apply as little throttle as
possible. Be sure to adapt your speed and driving to the prevailing road conditions.
The light also flashes when TCS is active. To improve the vehicle's traction when
starting off in deep snow, sand or gravel, it may be desirable to switch the ESC
switch.
system to Partial Off mode by momentarily pressing the ESC Off
- Tire Pressure Monitoring System (TPMS) Light
• Each tire, including the spare (if provided), should be checked monthly, when cold
and inflated to the inflation pressure recommended by the vehicle manufacturer on
the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a
different size than the size indicated on the vehicle placard or tire inflation pressure
label, you should determine the proper tire inflation pressure for those tires.)
• As an added safety feature, your vehicle has been equipped with a Tire Pressure
Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or
more of your tires is significantly under-inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and check your tires as soon as possible,
and inflate them to the proper pressure. Driving on a significantly under-inflated tire
causes the tire to overheat and can lead to tire failure. Under-inflation also reduces
fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping
ability.
94
WHAT TO DO IN EMERGENCIES
• IF THE LIGHT STARTS FLASHING INDICATING A LOW TIRE PRESSURE, ADJUST THE AIR
PRESSURE IN THE LOW TIRE TO THE AIR PRESSURE SHOWN ON THE VEHICLE PLACARD
OR TIRE INFLATION PRESSURE LABEL LOCATED ON THE DRIVER'S DOOR.
NOTE:
AFTER INFLATION, THE VEHICLE MAY NEED TO BE DRIVEN FOR 20 MINUTES
BEFORE THE FLASHING LIGHT WILL TURN OFF.
• Please note that the TPMS is not a substitute for proper tire maintenance, and it is the
driver’s responsibility to maintain correct tire pressure, even if under-inflation has not
reached the level to trigger illumination of the TPMS low tire pressure telltale.
• Your vehicle has also been equipped with a TPMS malfunction indicator to
indicate when the system is not operating properly. The TPMS malfunction
indicator is combined with the low tire pressure telltale. When the system detects
a malfunction, the telltale will flash for approximately one minute and then remain
continuously illuminated. This sequence will continue each time the vehicle is
restarted as long as the malfunction exists.
• When the malfunction indicator is illuminated, the system may not be able to
detect or signal low tire pressure as intended. TPMS malfunctions may occur for a
variety of reasons, including the installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS from functioning properly. Always
check the TPMS malfunction telltale after replacing one or more tires or wheels on
your vehicle, to ensure that the replacement or alternate tires and wheels allow the
TPMS to continue to function properly.
NOTE:
Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature
change. Keep this in mind when checking tire pressure inside a garage, especially in the
Winter. Example: If garage temperature is 68°F (20°C) and the outside temperature is
32°F (0°C), then the cold tire inflation pressure should be increased by 3 psi (21 kPa),
which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition.
CAUTION!
The TPMS has been optimized for the original equipment tires and wheels. TPMS
pressures and warning have been established for the tire size equipped on your
vehicle. Undesirable system operation or sensor damage may result when using
replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or
balance beads if your vehicle is equipped with a TPMS, as damage to the sensors
may result.
95
WHAT TO DO IN EMERGENCIES
- Engine Temperature Warning Light
• This light warns of an overheated engine condition.
• If the light turns on and a warning chime sounds while driving, safely pull over and
stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into
NEUTRAL and idle the vehicle. If the temperature reading does not return to
normal, turn the engine off immediately.
• We recommend that you do not operate the vehicle or engine damage will occur.
Have the vehicle serviced immediately.
WARNING!
A hot engine cooling system is dangerous. You or others could be badly burned by
steam or boiling coolant. You may want to call an authorized dealer for service if
your vehicle overheats.
BRAKE - Brake Warning Light
• The Brake Warning light illuminates when there is either a system malfunction or
the parking brake is applied. If the light is on and the parking brake is not applied,
it indicates a possible brake hydraulic malfunction, brake booster problem or an
Anti-Lock Brake System problem.
• Please have your vehicle serviced immediately.
WARNING!
Driving a vehicle with the red brake light on is dangerous. Part of the brake system
may have failed. It will take longer to stop the vehicle. You could have a collision.
Have the vehicle checked immediately.
- Malfunction Indicator Light (MIL)
• Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may
illuminate the MIL after engine start. The vehicle should be serviced if the light
stays on through several typical driving cycles. In most situations, the vehicle will
drive normally and not require towing.
• If the MIL flashes when the engine is running, serious conditions may exist that
could lead to immediate loss of power or severe catalytic converter damage. We
recommend you do not operate the vehicle. Have the vehicle serviced immediately.
Electronic Stability Control (ESC) OFF Activation/Malfunction Warning Light
• If the ESC OFF warning light comes on continuously with the engine running, a
malfunction has been detected.
• If this light remains on after several ignition cycles, and the vehicle has been
driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), we
recommend you drive to the nearest service center and have the vehicle serviced
immediately.
96
WHAT TO DO IN EMERGENCIES
- Charging System Light
• This light shows the status of the electrical charging system. If the charging system
light remains on, it means that the vehicle is experiencing a problem with the
charging system.
• We recommend you do not continue driving if the charging system light is on. Have
the vehicle serviced immediately.
- Oil Pressure Warning Light
• This light indicates low engine oil pressure. If the light turns on while driving, stop
the vehicle and shut off the engine as soon as possible. A chime will sound when
this light turns on.
• We recommend you do not operate the vehicle or engine damage will occur. Have
the vehicle serviced immediately.
- Anti-Lock Brake (ABS) Light
• This light monitors the Anti-Lock Brake System (ABS).
• If the light is not on during starting, stays on, or turns on while driving, we recommend
you drive to the nearest service center and have the vehicle serviced immediately.
- Electronic Throttle Control (ETC) Indicator Light
• This light informs you of a problem with the Electronic Throttle Control (ETC)
system.
• If a problem is detected, the light will come on while the engine is running. Cycle
the ignition when the vehicle has completely stopped and the shift lever is placed
in the PARK position; the light should turn off.
• If the light remains lit with the engine running, your vehicle will usually be drivable;
however, see an authorized service center immediately. If the light is flashing when
the engine is running, immediate service is required and you may experience reduced
performance, an elevated/rough idle or engine stall and your vehicle may require
towing.
- Air Bag Warning Light
• If the light is not on during starting, stays on, or turns on while driving, have the
vehicle serviced by an authorized service center immediately.
Fuel Cap/Loose Gas Cap Message
• If a “gas cap” message (shown as gASCAP) appears, tighten the gas cap until a
“clicking” sound is heard.
• Press the odometer reset button to turn the message off.
• If the message continues to appear for more than three days after tightening the
gas cap, see your authorized service center.
97
WHAT TO DO IN EMERGENCIES
Oil Change EVIC Indicator
Message
• If an “oil change” message (shown as "Change Oil Soon" and "Oil Change Needed")
appears and a single chime sounds, it is time for your next required oil change.
Resetting The Light After Servicing
• Turn the ignition switch to the ON/RUN position (do not start engine).
• Fully depress the accelerator pedal three times within 10 seconds.
• Turn the ignition switch to the OFF/LOCK position.
HOTOIL – Transmission Temperature Warning Message
• The HOTOIL cluster message will appear in the odometer accompanied with a
chime to indicate that there is excessive transmission fluid temperature that might
occur with severe usage such as trailer towing.
• It may also occur when operating the vehicle in a high torque converter slip condition,
such as 4-wheel-drive operation (e.g., snow plowing, off-road operation).
• If this HOTOIL message turns on, stop the vehicle and run the engine at idle or
faster, with the transmission in NEUTRAL until the message turns off.
CAUTION!
Continuous driving with the Transmission Temperature HOTOIL Warning message
illuminated will eventually cause severe transmission damage and transmission
failure.
WARNING!
Continued operation with the Transmission Temperature HOTOIL Warning message illuminated could cause the fluid to boil over, come into contact with the hot
engine or exhaust components causing a fire that may result in personal injury.
IF YOUR ENGINE OVERHEATS
• In any of the following situations, you can reduce the potential for overheating by
taking the appropriate action.
• On the highways — slow down.
• In city traffic — while stopped, place the transmission in NEUTRAL, but do not
increase engine idle speed.
NOTE:
There are steps that you can take to slow down an impending overheat condition:
• If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the
engine cooling system and turning the A/C off can help remove this heat.
98
WHAT TO DO IN EMERGENCIES
• You can also turn the temperature control to maximum heat, the mode control to floor
and the blower control to high. This allows the heater core to act as a supplement to
the radiator and aids in removing heat from the engine cooling system.
CAUTION!
Driving with a hot cooling system could damage your vehicle. If the temperature
gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air
conditioner turned off until the pointer drops back into the normal range. If the
pointer remains on HOT (H), and you hear continuous chimes, turn the engine off
immediately, and call for service.
WARNING!
You or others can be badly burned by hot engine coolant (antifreeze) or steam from
your radiator. If you see or hear steam coming from under the hood, do not open
the hood until the radiator has had time to cool. Never try to open a cooling system
pressure cap when the radiator or coolant bottle is hot.
JACKING AND TIRE CHANGING
Jack Location
• The jack and lug wrench are located in the rear storage compartment.
NOTE:
Turn the black plastic wing nut counter clockwise to loosen the jack from the storage bin.
Spare Tire Stowage
• To remove the spare tire from the carrier,
remove the tire cover, if equipped, and
remove the lug nuts with the lug wrench
turning them counterclockwise.
NOTE:
If you have added aftermarket accessories to the spare tire mounted carrier, it
cannot exceed a gross weight of 69 lbs
(31.3 kg) including the weight of the
spare tire.
99
WHAT TO DO IN EMERGENCIES
Preparations For Jacking
1. Park on a firm, level surface. Avoid ice or slippery areas.
2. Turn on the Hazard Warning flasher.
3. Set the parking brake.
4. Shift the automatic transmission into PARK, or a manual transmission into
REVERSE.
5. Turn the ignition to LOCK.
Block both the front and rear of the wheel
diagonally opposite of the jacking position. For example, if changing the right
front tire, block the left rear wheel.
NOTE:
Passengers should not remain in the vehicle when the vehicle is being jacked.
Jacking Instructions
1. Remove the spare tire, jack and tools
from the stored location.
2. Loosen (but do not remove) the wheel
lug nuts by turning them to the left
one turn while the wheel is still on the
ground.
3. Assemble the jack and jacking tools.
Connect the jack handle driver to the
extension, then to the lug wrench.
100
WHAT TO DO IN EMERGENCIES
4. Operate the jack from the front or the rear of the vehicle. Place the jack under
the axle tube, as shown. Do not raise the vehicle until you are sure the jack is fully
engaged.
5. Raise the vehicle by turning the jack
screw to the right. Raise the vehicle
only until the tire just clears the surface
and enough clearance is obtained to
install the spare tire. Minimum tire lift
provides maximum stability.
6. Remove the lug nuts and wheel.
7. Position the spare wheel/tire on the
vehicle and install the lug nuts with the
cone-shaped end toward the wheel.
Lightly tighten the lug nuts clockwise.
8. Lower the vehicle by turning the jack
screw to the left, and remove the jack.
9. Finish tightening the lug nuts. Push
down on the wrench while tightening
for increased leverage. Alternate nuts
until each nut has been tightened
twice. The correct wheel nut tightness
is 95 ft lbs (130 N·m). If in doubt
about the correct tightness, have
them checked with a torque wrench
by your authorized dealer or at a service station.
10. Remove the jack assembly and
wheel blocks.
11. Secure the tire, jack, and tools in
their proper locations.
12. Remove blocks from wheels.
101
WHAT TO DO IN EMERGENCIES
Road Tire Installation
1. Mount the road tire on the axle.
2. Install the remaining lug nuts with the cone shaped end of the nut toward the
wheel. Lightly tighten the lug nuts.
3. Lower the vehicle to the ground by turning the jack handle counterclockwise.
4. Finish tightening the lug nuts. Push down on the wrench while at the end of the
handle for increased leverage. Tighten the lug nuts in a star pattern until each nut
has been tightened twice. The correct tightness of each lug nut is 95 ft/lbs
(130 N·m). If in doubt about the correct tightness, have them checked with a
torque wrench by your authorized dealer or service station.
5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure
that all lug nuts are properly seated against the wheel.
CAUTION!
Do not attempt to raise the vehicle by jacking on locations other than those
indicated in the Jacking Instructions for this vehicle.
102
WHAT TO DO IN EMERGENCIES
WARNING!
• Do not attempt to change a tire on the side of the vehicle close to moving
traffic. Pull far enough off the road to avoid the danger of being hit when
operating the jack or changing the wheel.
• Being under a jacked-up vehicle is dangerous. The vehicle could slip off the
jack and fall on you. You could be crushed. Never put any part of your body
under a vehicle that is on a jack. If you need to get under a raised vehicle, take
it to a service center where it can be raised on a lift.
• Never start or run the engine while the vehicle is on a jack.
• The jack is designed to be used as a tool for changing tires only. The jack
should not be used to lift the vehicle for service purposes. The vehicle should
be jacked on a firm level surface only. Avoid ice or slippery areas.
• Carefully follow these tire changing warnings to help prevent personal injury or
damage to your vehicle:
• Always park on a firm, level surface as far from the edge of the roadway as
possible before raising the vehicle.
• Turn on the Hazard Warning flasher.
• Block the wheel diagonally opposite the wheel to be raised.
• Set the parking brake firmly and set an automatic transmission in PARK; a
manual transmission in REVERSE.
• Do not let anyone sit in the vehicle when it is on a jack.
• Do not get under the vehicle when it is on a jack.
• Only use the jack in the positions indicated and for lifting this vehicle
during a tire change.
• If working on or near a roadway, be extremely careful of motor traffic.
• To assure that spare tires, flat or inflated, are securely stowed, spares must
be stowed with the valve stem facing the ground.
• Raising the vehicle higher than necessary can make the vehicle less stable
and cause a collision. It could slip off the jack and hurt someone near it.
Raise the vehicle only enough to remove the tire.
• To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel
nuts fully until the vehicle has been lowered.
• A loose tire or jack, thrown forward in a collision or hard stop, could
endanger the occupants of the vehicle. Always stow the jack parts and the
spare tire in the places provided.
• To avoid the risk of forcing the vehicle off the jack, do not tighten the lug
nuts fully until the vehicle is lowered to the ground.
103
WHAT TO DO IN EMERGENCIES
JUMP-STARTING
• If your vehicle has a discharged battery
it can be jump-started using a set of
jumper cables and a battery in another
vehicle or by using a portable battery
booster pack.
• Jump-starting can be dangerous if done
improperly so please follow the procedures in this section carefully.
NOTE:
When using a portable battery booster
pack follow the manufacturer’s operating
instructions and precautions.
Preparations for Jump-Start
• The battery in your vehicle is located in the right rear of the engine compartment.
• Set the parking brake, shift the automatic transmission into PARK and turn the
ignition to LOCK.
• Turn off the heater, radio, and all unnecessary electrical accessories.
• If using another vehicle to jump-start the battery, park the vehicle within the jumper
cables reach, set the parking brake and make sure the ignition is OFF.
Jump-Starting Procedure
• Connect the positive (+) end of the jumper cable to the positive (+) post of the
discharged vehicle.
• Connect the opposite end of the positive (+) jumper cable to the positive (+) post
of the booster battery.
• Connect the negative end (-) of the jumper cable to the negative (-) post of the
booster battery.
• Connect the opposite end of the negative (-) jumper cable to a good engine ground
(exposed metal part of the discharged vehicle’s engine) away from the battery and
the fuel injection system.
• Start the engine in the vehicle that has the booster battery, let the engine idle a few
minutes, and then start the engine in the vehicle with the discharged battery.
Once the engine is started, remove the jumper cables in the reverse sequence:
• Disconnect the negative (-) jumper cable from the engine ground of the vehicle
with the discharged battery.
• Disconnect the negative end (-) of the jumper cable from the negative (-) post of
the booster battery.
104
WHAT TO DO IN EMERGENCIES
• Disconnect the opposite end of the positive (+) jumper cable from the positive (+)
post of the booster battery.
• Disconnect the positive (+) end of the jumper cable from the positive (+) post of
the discharged vehicle.
• If frequent jump-starting is required to start your vehicle you should have the
battery and charging system inspected at your authorized dealer.
CAUTION!
• Do not use a portable battery booster pack or any other booster source with a
system voltage greater than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.
• Failure to follow these procedures could result in damage to the charging
system of the booster vehicle or the discharged vehicle.
• Accessories that can be plugged into the vehicle power outlets draw power from
the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Eventually, if plugged in long enough, the vehicle’s battery will discharge
sufficiently to degrade battery life and/or prevent the engine from starting.
WARNING!
• When temperatures are below the freezing point, electrolyte in a discharged
battery may freeze. Do not attempt jump-starting because the battery could
rupture or explode and cause personal injury. Battery temperature must be
brought above the freezing point before attempting a jump-start.
• Take care to avoid the radiator cooling fan whenever the hood is raised. It can start
anytime the ignition switch is on. You can be injured by moving fan blades.
• Remove any metal jewelry, such as watch bands or bracelets, that might make
an inadvertent electrical contact. You could be severely injured.
• Batteries contain sulfuric acid that can burn your skin or eyes and generate
hydrogen gas which is flammable and explosive. Keep open flames or sparks
away from the battery.
• Do not allow vehicles to touch each other as this could establish a ground
connection and personal injury could result.
• Failure to follow this procedure could result in personal injury or property damage
due to battery explosion.
• Do not connect the cable to the negative post (-) of the discharged battery. The
resulting electrical spark could cause the battery to explode and could result in
personal injury.
105
WHAT TO DO IN EMERGENCIES
EMERGENCY TOW HOOKS
• If your vehicle is equipped with tow hooks, they are mounted in the front and the rear.
NOTE:
For off-road recovery, it is recommended to use both of the front tow hooks to
minimize the risk of damage to the vehicle.
CAUTION!
Tow hooks are for emergency use only, to rescue a vehicle stranded off-road. Do not
use tow hooks for tow truck hookup or highway towing. You could damage your
vehicle. Tow straps are recommended when towing the vehicle; chains may cause
vehicle damage.
WARNING!
• Chains are not recommended for freeing a stuck vehicle. Chains may break,
causing serious injury or death.
• Stand clear of vehicles when pulling with tow hooks. Tow straps may become
disengaged, causing serious injury.
SHIFT LEVER OVERRIDE
• If a malfunction occurs and the shift
lever cannot be moved out of the PARK
position, you can use the following
procedure to temporarily move the
shift lever:
• To access the shift lever override,
remove the override cover located on
the shift lever bezel, next to the shift
lever.
• Firmly set the parking brake.
• Turn the ignition switch to the ACC
or ON position without starting the
engine.
• Press and maintain firm pressure on
the brake pedal.
• Using a screwdriver or similar tool, press and hold the override tab through the
access port on the center console.
• Move the shift lever into the NEUTRAL position.
• The vehicle may then be started in NEUTRAL.
• Reinstall the override cover.
106
WHAT TO DO IN EMERGENCIES
TOWING A DISABLED VEHICLE
• The manufacturer requires towing your vehicle with all four wheels OFF the ground
using a flatbed.
CAUTION!
Towing this vehicle using any other method could result in extensive damage to the
transfer case and/or transmission.
FREEING A STUCK VEHICLE
• If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a
rocking motion. Turn your steering wheel right and left to clear the area around the
front wheels. Then shift back and forth between DRIVE/1st gear and REVERSE.
Using minimal accelerator pedal pressure to maintain the rocking motion, without
spinning the wheels, is most effective.
NOTE:
If your vehicle is equipped with Traction Control or Electronic Stability Control (ESC),
turn the system OFF before attempting to “rock” the vehicle.
CAUTION!
• Racing the engine or spinning the wheels may lead to transmission overheating
and failure. Allow the engine to idle with the shift lever in NEUTRAL for at least
one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free
a stuck vehicle.
• When “rocking” a stuck vehicle by moving between DRIVE/1st gear and
REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain
damage may result.
• Revving the engine or spinning the wheels too fast may lead to transmission
overheating and failure. It can also damage the tires. Do not spin the wheels
above 30 mph (48 km/h) while in gear (no transmission shifting occurring).
WARNING!
Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds
may cause damage, or even failure, of the axle and tires. A tire could explode and
injure someone. Do not spin your vehicle's wheels faster than 30 mph (48 km/h)
or for longer than 30 seconds continuously without stopping when you are stuck
and do not let anyone near a spinning wheel, no matter what the speed.
107
WHAT TO DO IN EMERGENCIES
EVENT DATA RECORDER (EDR)
• This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of
an EDR is to record, in certain crash or near crash-like situations, such as an air
bag deployment or hitting a road obstacle, data that will assist in understanding
how a vehicle’s systems performed. The EDR is designed to record data related to
vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as:
• How various systems in your vehicle were operating;
• Whether or not the driver and passenger safety belts were buckled/fastened;
• How far (if at all) the driver was depressing the accelerator and/or brake pedal;
and,
• How fast the vehicle was traveling.
• These data can help provide a better understanding of the circumstances in which
crashes and injuries occur.
NOTE:
EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no
data are recorded by the EDR under normal driving conditions and no personal data
(e.g. name, gender, age, and crash location) are recorded. However, other parties,
such as law enforcement, could combine the EDR data with the type of personally
identifying data routinely acquired during a crash investigation.
• To read data recorded by an EDR, special equipment is required, and access to the
vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties
such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.
108
MAINTAINING YOUR VEHICLE
OPENING THE HOOD
• Release the two hood latches located
on the left and right side of the hood.
• Raise the hood and locate the safety
latch, in the middle of the hood opening.
• Push the latch to the left side of the
vehicle, to open the hood. You may
have to push down slightly on the hood
before pushing the safety latch.
• Insert the support rod into the slot on
the hood.
• To close the hood, remove the support
rod and place it in the retaining clip,
then lower the hood slowly.
• Secure both of the hood latches.
WARNING!
Be sure the hood is fully latched before driving your vehicle. If the hood is not fully
latched, it could open when the vehicle is in motion and block your vision. Failure
to follow this warning could result in serious injury or death.
109
110
3.6L Engine
ENGINE COMPARTMENT
MAINTAINING YOUR VEHICLE
MAINTAINING YOUR VEHICLE
FLUIDS AND CAPACITIES
Component
Engine Coolant–
3.6L Engine
Engine Oil with filter–
3.6L Engine
Engine Oil Filter–
3.6L Engine
Spark Plug–
3.6L Engine
Automatic Transmission
Manual Transmission
Transfer Case
Axle differential (front)
Fluid, Lubricant, or
Genuine Part
We recommend you use
MOPAR® Antifreeze/
Coolant 10 Year/150,000
Mile Formula OAT (Organic
Additive Technology).
We recommend you use
API Certified SAE 5W-20
Engine Oil, meeting the
requirements of Chrysler
Material Standard
MS-6395. Refer to your
engine oil filler cap for
correct SAE grade.
We recommend you use
MOPAR® brand Engine Oil
Filters.
We recommend you use
MOPAR® Spark Plugs.
We recommend you only
use MOPAR® ATF+4®
Automatic Transmission
Fluid.
Failure to use ATF+4 fluid
may affect the function
or performance of your
transmission.
We recommend you use
MOPAR® Manual
Transmission Lubricant.
We recommend you use
MOPAR® ATF+4®
Automatic Transmission
Fluid.
We recommend you use
MOPAR® Gear & Axle
Lubricant (SAE 80W-90)
(API GL-5).
Capacities
10.5 Quarts (9.9 Liters)
Includes coolant recovery
bottle filled to MAX level.
6 quarts (5.7 Liters)
—
—
—
—
—
—
111
MAINTAINING YOUR VEHICLE
Component
Axle differential (rear)
Brake Master Cylinder
Power Steering Reservoir
Fuel Selection 2 Door
Fuel Selection 4 Door
Fluid, Lubricant, or
Capacities
Genuine Part
226 RBI (Model 44) We recommend you use
MOPAR® Gear & Axle
Lubricant (SAE 80W-90)
(API GL-5). For trailer
towing,We recommend
—
you use MOPAR® Synthetic
Gear & Axle Lubricant
(SAE 75W-140). Models
equipped with Trac-Lok™
require an additive.
We recommend you use
MOPAR® DOT 3 Brake
Fluid, SAE J1703.
—
If DOT 3, SAE J1703
brake fluid is not available,
then DOT 4 is acceptable.
We recommend you use
MOPAR® Power Steering
—
Fluid +4, MOPAR® or
ATF+4® Automatic
Transmission Fluid.
18.6 Gallons (70 Liters)
87 Octane
(Approximate)
22.5 Gallons (85 Liters)
87 Octane
(Approximate)
E85 FLEXIBLE FUEL — 3.6L ENGINE ONLY
Refer to your Owner's Manual on the DVD for further details.
CAUTION!
Only vehicles with the E-85 fuel filler door label or a yellow gas cap can operate on
E-85.
112
MAINTAINING YOUR VEHICLE
MAINTENANCE SCHEDULE
Your vehicle is equipped with an automatic oil change indicator system. The oil change
indicator system will remind you that it is time to take your vehicle in for scheduled
maintenance.
Based on engine operation conditions, the oil change indicator message will
illuminate. This means that service is required for your vehicle. Operating conditions
such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures,
and E85 fuel usage will influence when the “Change Oil” or “Oil Change Required”
message is displayed. Severe Operating Conditions can cause the change oil
message to illuminate as early as 3,500 miles (5,600 km) since last reset. Have your
vehicle serviced as soon as possible, within the next 500 miles (805 km).
On Electronic Vehicle Information Center (EVIC) equipped vehicles, “Oil Change
Required” will be displayed in the EVIC and a single chime will sound, indicating that
an oil change is necessary.
On Non-EVIC equipped vehicles, “Change Oil” will flash in the instrument cluster
odometer and a single chime will sound, indicating that an oil change is necessary.
Your authorized dealer will reset the oil change indicator message after completing the
scheduled oil change. If a scheduled oil change is performed by someone other than
your authorized dealer, the message can be reset by referring to the steps described
under “Electronic Vehicle Information Center (EVIC)/Oil Change Required” in “Understanding Your Instrument Panel” or under “Instrument Cluster Description/Odometer/
Trip Odometer” in “Understanding Your Instrument Panel” for further information.
NOTE:
Under no circumstances should oil change intervals exceed 10,000 miles
(16,000 km) or twelve months, whichever comes first.
Once A Month Or Before A Long Trip:
• Check engine oil level
• Check windshield washer fluid level
• Check the tire inflation pressures and look for unusual wear or damage
• Check the fluid levels of the coolant reservoir, brake master cylinder, power steering
and transmission as needed
• Check function of all interior and exterior lights
113
MAINTAINING YOUR VEHICLE
Required Maintenance Intervals.
Refer to the maintenance schedules on the following page for the required maintenance intervals.
•
•
•
•
•
•
•
•
•
114
At Every Oil Change Interval As Indicated By Oil Change Indicator System:
Change oil and filter
Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the
oil indicator system turns on.
Inspect battery and clean and tighten terminals as required
Inspect automatic transmission fluid if equipped with dipstick
Inspect brake pads, shoes, rotors, drums, hoses and park brake
Inspect engine cooling system protection and hoses
Inspect exhaust system
Inspect engine air cleaner if using in dusty or off-road conditions
Inspect all door latches for presence of grease, reapply if necessary.
X
Inspect the brake linings, parking brake
function.
30,000
X
X
X
X
X
X
X
X
X
X
X
X
Flush and replace the engine coolant
at 10 years or 150,000 miles
(240,000 km) whichever comes first.
50,000
Replace the ignition cables.
X
60,000
X
X
40,000
X
70,000
Replace spark plugs **
Replace engine air cleaner filter.
Additional Maintenance
Inspect transfer case fluid.
X
X
Inspect the front and rear axle fluid.
X
Inspect front suspension, tie rod ends,
and replace if necessary.
Inspect the CV joints.
X
X
X
X
X
X
X
X
X
20,000
32,000
Or Kilometers:
90,000
X
48,000
X
64,000
X
80,000
X
96,000
X
6
80,000
X
7
112,000
X
8
128,000
X
9
144,000
Additional Inspections
15
14
13
12
11
10
160,000
5
100,000
176,000
4
110,000
192,000
3
120,000
208,000
2
130,000
224,000
Or Years:
140,000
240,000
Mileage or time passed
(whichever comes first)
150,000
Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
Maintenance Chart
MAINTAINING YOUR VEHICLE
115
116
48,000
20,000
32,000
Or Kilometers:
Change transfer case fluid if using your
vehicle for any of the following: police,
taxi, fleet, or frequent trailer towing.
X
X
X
Change the manual transmission fluid
if using your vehicle for any of the
following: trailer towing, snow plowing,
heavy loading, taxi, police, delivery
service (commercial service), off-road,
desert operation or more than 50% of
your driving is at sustained high speeds
during hot weather, above 90°F (32°C).
X
X
Change the automatic transmission fluid
and filter(s).
X
64,000
X
80,000
X
96,000
X
112,000
Change automatic transmission fluid and
filter if using your vehicle for any of the
following: trailer towing, snow plowing,
heavy loading, taxi, police, delivery
service (commercial service), off-road,
desert operation or more than 50% of
your driving is at sustained high speeds
during hot weather, above 90°F (32°C).
15
14
13
30,000
12
40,000
11
50,000
10
60,000
9
70,000
8
80,000
128,000
7
90,000
144,000
6
100,000
160,000
5
110,000
176,000
4
120,000
192,000
3
130,000
208,000
2
140,000
224,000
Or Years:
150,000
240,000
Mileage or time passed
(whichever comes first)
MAINTAINING YOUR VEHICLE
64,000
48,000
20,000
32,000
90,000
70,000
60,000
50,000
40,000
30,000
• You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the
right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
• Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and
performance. This could cause an accident.
WARNING!
** The spark plug change interval is mileage based only, yearly intervals do not apply.
Change front and rear axle fluid if
using your vehicle for police, taxi, fleet,
off-road or frequent trailer towing.
X
80,000
Or Kilometers:
80,000
X
96,000
X
7
112,000
X
8
128,000
Inspect and replace PCV valve if
necessary.
15
14
13
12
11
10
9
144,000
6
100,000
160,000
5
110,000
176,000
4
120,000
192,000
3
130,000
208,000
2
140,000
224,000
Or Years:
150,000
240,000
Mileage or time passed
(whichever comes first)
MAINTAINING YOUR VEHICLE
117
MAINTAINING YOUR VEHICLE
MAINTENANCE RECORD
Odometer
20,000 Miles
(32,000 km) or
2 Years
30,000 Miles
(48,000 km) or
3 Years
40,000 Miles
(64,000 km) or
4 Years
50,000 Miles
(80,000 km) or
5 Years
60,000 Miles
(96,000 km) or
6 Years
70,000 Miles
(112,000 km) or
7 Years
80,000 Miles
(128,000 km) or
8 Years
90,000 Miles
(144,000 km) or
9 Years
100,000 Miles
(160,000 km) or
10 Years
110,000 Miles
(176,000 km) or
11 Years
120,000 Miles
(192,000 km) or
12 Years
130,000 Miles
(208,000 km) or
13 Years
140,000 Miles
(224,000 km) or
14 Years
150,000 Miles
(240,000 km) or
15 Years
118
Date
Signature, Authorized Service
Center
MAINTAINING YOUR VEHICLE
FUSES
Integrated Power Module (fuses)
119
MAINTAINING YOUR VEHICLE
• The Integrated Power Module is located in the engine compartment near the
battery. This center contains cartridge fuses, mini-fuses and relays.
Cavity
J1
J2
J3
J4
J5
J6
Cartridge Fuse
—
30 Amp Pink
—
25 Amp Natural
25 Amp Natural
40 Amp Green
J7
30 Amp Pink
J8
J9
J10
—
40 Amp Green
30 Amp Pink
J11
J12
J13
J14
J15
J17
J18
30
30
60
40
40
40
20
J19
J20
J21
J22
M1
60 Amp Yellow
30 Amp Pink
20 Amp Blue
—
M2
M3
M4
M5
M6
M7
M8
M9
120
Amp
Amp
Amp
Amp
Amp
Amp
Amp
Pink
Pink
Yellow
Green
Green
Green
Blue
Mini Fuse
Description
—
Transfer Case Module
—
Driver Door Node
Passenger Door Node
Anti-Lock Brake System (ABS) Pump
Feed/ESC
Anti-Lock Brake System (ABS) Valve
Feed/ESC
—
PZEV Sec Motor Feed/Flex Fuel
Headlamp Wash Relay/Manifold
Tuning Valve
Sway Bar
Rear Blower Motor/Radiator Fan
Ignition Off Draw (IOD) — Main
EBL (Rear Window Defogger)
Front Blower
Starter Solenoid
Powertrain Control Module (PCM)
Trans Range
Radiator Fan
Front Wiper LO/HI
Front/Rear Washer
Spare
15 Amp Blue
Center High-Mounted Stop Light
(CHMSL)/Switch Stop Lamp Feed
20 Amp Yellow Relay Trailer Lighting (Stop)
20 Amp Yellow Frt/Rear Axle Locker Relay
—
—
25 Amp Natural
Power Inverter - If Equipped
20 Amp Yellow Power Outlet #1/Rain Sensor
20 Amp Yellow Power Outlet #2 (BATT/ACC SELECT)
20 Amp Yellow Front Heated Seat
20 Amp Yellow Rear Heated Seat (If Equipped)
MAINTAINING YOUR VEHICLE
Cavity
M10
M11
M12
M13
M14
M15
M16
M17
M18
M19
M20
M21
M22
M23
M24
M25
Cartridge Fuse
Mini Fuse
15 Amp Blue
Description
Ignition Off Draw — Vehicle Entertainment System (IOD-VES), Satellite
Digital Audio Receiver (SDARS), DVD,
Hands-Free Module (HFM), RADIO,
Antenna (ANT), Universal Garage
Door Opener (UGDO), Vanity Lamp
(VANITY LP)
10 Amp Red
(Ignition Off Draw) IOD-HVAC/ATC,
MW SENSR, Underhood Lamp
(UH LMP)
30 Amp Green
Amplifier (AMP)
20 Amp Yellow Ignition Off Draw— Cabin Compartment Node (IOD-CCN), Wireless
Control Module (WCM), SIREN,
Multifunction Control Switch
(MULTIFCTN SW)
20 Amp Yellow Trailer Tow (Export Only)
20 Amp Yellow COL MOD, IR SNS, Heater Ventilation, Air Conditioning/Automatic
Temperature Control (HVAC/ATC),
Rear View Mirror (RR VW MIR),
Cabin Compartment Node (CCN),
Transfer Case Switch (T-CASE SW),
RUN/ST, Multi-Function Control
Switch (MULTIFTCN SW), Tire
Pressure Monitor (TPM), Glow Plug
Module (GLW PLG MOD) — Export
Diesel Only
10 Amp Red
Occupant Restraint Controller (ORC)
15 Amp Blue
Left Tail/License/Park Lamp
(LT-TAIL/LIC/PRK LMP)
15 Amp Blue
Right Tail/Park/Run Lamp
(RT-TAIL/PRK/RUN LMP)
25 Amp Natural Auto Shut Down (ASD #1 and #2)
15 Amp Blue
Cabin Compartment Node Interior
Light (CCN INT LIGHT), Switch Bank
(SW BANK)
20 Amp Yellow Auto Shut Down (ASD #3)
10 Amp Red
Right Horn (RT HORN (HI/LOW)
10 Amp Red
Left Horn (LT HORN (HI/LOW)
25 Amp Natural Rear Wiper (REAR WIPER)
20 Amp Yellow Fuel Pump (FUEL PUMP), Diesel
Lift Pump (DSL LIFT PUMP) —
Export Only
121
MAINTAINING YOUR VEHICLE
Cavity
M26
Cartridge Fuse
Mini Fuse
10 Amp
M27
M28
M29
10 Amp
10 Amp
10 Amp
M30
15 Amp
M31
20 Amp
M32
10 Amp
M33
10 Amp
M34
10 Amp
M35
M36
10 Amp
20 Amp
M37
10 Amp
M38
25 Amp
122
Description
Power Window Switch/Driver Window
Red
Switch
Red
Ignition Switch Feed, Wireless Module
Red
PCM Feed/TCM
Red
Powertrain
Wiper Motor Frt, J1962 Diagnostic
Blue
Feed
Yellow Backup Lamps (B/U LAMPS)
Occupant Restraint Controller (ORC),
Red
TT EUROPE
Next Generation Controller (NGC),
Red
Global Powertrain Engine Controller
(GPEC)
Park Assist (PRK ASST), Heater
Ventilation, Air Conditioning Module
Red
(HVAC MOD), Headlamp Wash
(HDLP WASH), Compass (COMPAS)
Red
Heated Mirrors
Yellow Power Outlet
Anti-Lock Brake System (ABS) ,
Electronic Stability Control (ESC),
Red
Stop Lamp Switch (STP LP SW),
Fuel Pump Rly Hi Control
Lock/Unlock Motors
Natural
(LOCK/UNLOCK MTRS)
MAINTAINING YOUR VEHICLE
TIRE PRESSURES
• Check the inflation pressure of each tire, including the spare tire, at least monthly
and inflate to the recommended pressure for your vehicle.
• The tire pressures recommended for your vehicle are found on the “Tire and
Loading Information” label located on the driver’s side door opening.
2 Door Tire Placard Location
4 Door Tire Placard Location
NOTE:
Refer to the Owner's Manual on the DVD for more information regarding tire warnings
and instructions.
123
MAINTAINING YOUR VEHICLE
WARNING!
• Overloading of your tires is dangerous. Overloading can cause tire failure, affect
vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
• Improperly inflated tires are dangerous and can cause collisions. Under-inflation
is the leading cause of tire failure and may result in severe cracking, component
separation, or “blow out”. Over-inflation reduces a tire’s ability to cushion shock.
Objects on the road and chuck holes can cause damage that results in tire failure.
Unequal tire pressures can cause steering problems. You could lose control of
your vehicle. Over-inflated or under-inflated tires can affect vehicle handling and
can fail suddenly, resulting in loss of vehicle control.
WHEEL AND WHEEL TRIM CARE
• All wheels and wheel trim, especially aluminum and chrome plated wheels, should
be cleaned regularly with a mild soap and water to prevent corrosion.
• To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or
equivalent or select a non-abrasive, non-acidic cleaner.
CAUTION!
Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use
oven cleaner. These products may damage the wheel's protective finish. Avoid
automatic car washes that use acidic solutions or harsh brushes that may damage
the wheel's protective finish. Only MOPAR® Wheel Cleaner or equivalent is
recommended.
EXTERIOR BULBS
Bulb Number
3157
LED (*)
PSX24W
3157
168
H13
194
LIGHT BULBS – Exterior
Backup, Tail, Stop, Turn Lamp
Center High-Mounted Stop Lamp (CHMSL)
Fog Lamp – If Equipped
Front Park/Turn Signal
Front Side Marker
Headlamp – Low Beam
License Lamp
* CHMSL is not serviceable. It is a LED lamp. To replace the LED, the entire CHMSL
assembly must be replaced.
124
CONSUMER ASSISTANCE
CHRYSLER GROUP LLC CUSTOMER CENTER
P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–877–426–5337
CHRYSLER CANADA INC. CUSTOMER CENTER
P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1–800–465–2001 (English)
Phone: 1–800–387–9983 (French)
ASSISTANCE FOR THE HEARING IMPAIRED
• To assist customers who have hearing difficulties, the manufacturer has installed
special TDD (Telecommunication Devices for the Deaf) equipment at its customer
center. Any hearing or speech impaired customer, who has access to a TDD or a
conventional teletypewriter (TTY) in the United States, can communicate with the
manufacturer by dialing 1–800–380–CHRY. Canadian residents with hearing
difficulties that require assistance can use the special needs relay service offered
by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial
1–800–855–0511 to connect with a Bell Relay Service operator.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth
defects, or other reproductive harm. In addition, certain fluids contained in
vehicles and certain products of component wear contain, or emit, chemicals
known to the State of California to cause cancer and birth defects, or other
reproductive harm.
PUBLICATIONS ORDERING
• If you are the first registered retail owner of your vehicle, you may obtain one free
printed copy of the Owner's Manual, Warranty Booklet or Radio Manuals on your
DVD by calling 1–877–426–5337 (U.S.) or 1–800–387–1143 (Canada) or by
contacting your dealer.
• Replacement User Guide kits or DVDs or, if you prefer, additional printed copies of
the Owner's Manual, Warranty Booklet or Radio Manuals may be purchased by
visiting www.techauthority.com or by calling 1–877–890–4038 (U.S.) or 1–800–
387–1143 (Canada). Visa, Master Card, American Express and Discover orders are
accepted. If you prefer mailing your order, please call the above numbers for an
order form.
125
CONSUMER ASSISTANCE
NOTE:
• A street address is required when ordering manuals (no P.O. Boxes).
• The Owner's Manual and User Guide electronic files are also available on the
Chrysler, Jeep, Ram Truck and Dodge websites.
• Click on the "For Owners" tab, select "Owner/Service Manuals", then select your
desired model year and vehicle from the drop down lists.
REPORTING SAFETY DEFECTS IN THE 50 UNITED
STATES AND WASHINGTON, D.C.
• If you believe that your vehicle has a defect that could cause a collision or cause
injury or death, you should immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying the manufacturer.
• If NHTSA receives similar complaints, it may open an investigation, and if it finds
that a safety defect exists in a group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in individual problems
between you, your authorized dealer and the manufacturer.
• To contact NHTSA, you may either call the Auto Safety Hotline toll free at
1–888–327–4236 (TTY: 1–800–424–9153), or go to http://www.safercar.gov; or
write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE., West Building,
Washington, D.C. 20590. You can also obtain other information about motor
vehicle safety from http://www.safercar.gov.
In Canada
• If you believe that your vehicle has a safety defect, you should contact the
Customer Service Department immediately. Canadian customers who wish to
report a safety defect to the Canadian government should contact Transport
Canada, Motor Vehicle Defect Investigations and Recalls at 1-800-333-0510 or
go to http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-index-53.htm
• French Canadian customers who wish to report a safety defect to the Canadian
government should contact Transport Canada, Motor Vehicle Defect Investigations
and Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/securiteroutiere/
126
MOPAR ACCESSORIES
AUTHENTIC ACCESSORIES BY MOPAR®
• The following highlights just some of the many Authentic Jeep Accessories by Mopar
featuring a fit, finish, and functionality specifically for your Jeep Wrangler.
• In choosing Authentic Accessories you gain far more than expressive style, premium
protection, or extreme entertainment, you also benefit from enhancing your vehicle
with accessories that have been thoroughly tested and factory-approved.
• For the full line of Authentic Jeep Accessories by Mopar, visit your local Jeep
dealership or online at mopar.com.
Chrome:
• Grille
• Mirror Covers
• Door Handle Covers
• Tubular Side Steps
• Fuel Door
• Door Hinge Covers
• Tubular Bumper
• Tail Lamp Guards
Off Road:
• Off Road Bumpers
• Winches
• Exhaust
• Rock Rails
• Lift Kits
• Skid Plates
• Off Road Lights
Exterior:
• Black Tubular Side Steps
• Front End Cover
• Air Deflectors
• Soft Tops
• Hard Top Storage Dolly
•
•
•
•
Black Tubular Bumpers
Cab Covers
Wheels
Splash Guards
• Running Boards
• Spare Tire Covers
• Hard Tops
• Fender Flares
• Slush Floor Mats
• Instrument Panel Appliques
• Door Sill Guards
Interior:
• Premium Carpet Floor Mats
• Seat Covers
Electronics:
• Sirius Satellite Radio
• Portable Navigation Systems • Uconnect® Web (WiFi)
• Heated Seats
• Ambient Footwell Lighting • iPod® Adapter
• Fog Lights
• Electronic Vehicle Tracking
System
Carriers:
• Freedom Top Carriers
• Bike Carriers
• Spare Tire-mount Ski
• Hitch Receivers and
Trailering Accessories
iPod® is a registered trademark of Apple, Inc.
127
INDEX
Airbag . . . . . . . . . . . . . .
Air Conditioning . . . . . . . .
Antifreeze (Engine Coolant) . .
Arming Theft System (Security
Alarm) . . . . . . . . . . . .
Automatic Headlights . . . . .
Automatic Temperature
Control (ATC) . . . . . . . .
. . . .12
. . . .25
. . .111
. . . .11
. . . .21
. . . .25
Belts, Seat . . . . . . . . . . . . . . .11
Break-In Recommendations,
New Vehicle . . . . . . . . . . . . .20
Bulb Replacement . . . . . . . . . .124
Calibration, Compass . . . . .
Capacities, Fluid . . . . . . . .
Change Oil Indicator . . . . . .
Changing A Flat Tire . . . . . .
Child Restraint . . . . . . . . .
Child Restraint Tether Anchors
Climate Control . . . . . . . . .
Compass Calibration . . . . . .
Cooling System
Coolant Capacity . . . . . .
Selection of Coolant
(Antifreeze) . . . . . . . . .
Cruise Control (Speed Control)
Customer Assistance . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .82
.111
. .98
. .99
. .13
. .13
. .25
. .82
. . .111
. . .111
. . . .23
. . .125
Defects, Reporting . . . . . . . . . .126
Dimmer Control. . . . . . . . . . . . .21
Dimmer Switch, Headlight . . . . . .21
Disarming, Theft System . . . . . . .11
Driver Cockpit . . . . . . . . . . . . . .6
ECO . . . . . . . . . . . . . . . . . . .83
Electronics
Your Vehicle's Sound System . .40
Electronic Speed Control
(Cruise Control) . . . . . . . . . . .23
Electronic Stability Control (ESC) . . .94
Electronic Vehicle Information
Center (EVIC) . . . . . . . . . .82, 83
Emergency, In Case of
Brake Warning Light . . . . . . .96
Jacking . . . . . . . . . . . . . . .99
Overheating . . . . . . . . . . . .98
128
Engine
Break-In Recommendations
Compartment . . . . . . .
Fuel Requirements . . . .
Oil . . . . . . . . . . . . . .
Oil Selection . . . . . . . .
Overheating . . . . . . . .
Event Data Recorder . . . . . .
Exterior Lights. . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .20
.110
.111
.111
.111
. .98
.108
.124
Flash-To-Pass . . . . . . . . . . . . . .21
Fluid Capacities. . . . . . . . . . . .111
Fluids, Lubricants and
Genuine Parts . . . . . . . . . . .111
Fog Lights . . . . . . . . . . . . .21, 22
Folding Rear Seat . . . . . . . . . . .17
Freeing A Stuck Vehicle . . . . . . .107
Front Heated Seats. . . . . . . . . . .19
Fuel
Filler Cap (Gas Cap) . . . . . . .97
Requirements . . . . . . . . . .111
Tank Capacity . . . . . . . . . .111
Fuse . . . . . . . . . . . . . . . . . .119
Fuses. . . . . . . . . . . . . . . . . .119
Headlights
Automatic . . . . . . . . .
Dimmer Switch . . . . . .
High Beam . . . . . . . . .
Heated Seats . . . . . . . . . .
High Beam/Low Beam Select
(Dimmer) Switch . . . . . .
Hood Release . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.21
.21
.21
.19
. . . .21
. . .109
Instrument Cluster . . . . . . . . . . . .8
Indicators . . . . . . . . . . . . . .9
Instrument Cluster Warning
Lights . . . . . . . . . . . . . . .8, 94
Integrated Power Module (Fuses) . .119
Intermittent Wipers (Delay Wipers) . .22
Inverter Outlet (115V) . . . . . . . . .84
Inverter, Power . . . . . . . . . . . . .84
iPod®/USB/MP3 Control . . . . . . . .75
Bluetooth Streaming Audio . . .82
Jacking Instructions . . . . . . . . .100
Jack Location . . . . . . . . . . . . . .99
INDEX
Jack Operation . . . . . . . . . .99, 100
Jump Starting . . . . . . . . . . . . .104
Key Fob . . . . . . . . . . . . . . . . .10
Key Fob Programmable Features . . .83
Lane Change and Turn Signals .
Lane Change Assist . . . . . . .
LATCH (Lower Anchors and
Tether for CHildren). . . . . .
Lights
Engine Temperature Warning
Tire Pressure Monitoring
(TPMS) . . . . . . . . . . . .
Turn Signal . . . . . . . . . .
Warning (Instrument Cluster
Description) . . . . . . . . .
. . .22
. . .22
. . .13
. .96
. . .94
. . .22
. . . .8
Maintenance Record . . . . . . . . .118
Maintenance Schedule . . . . . . . .113
Malfunction Indicator Light
(Check Engine) . . . . . . . . . . .96
Navigation Voice Prompt
Volume . . . . . . . . . . . . .57, 67
New Vehicle Break-In Period . . . . .20
Oil Change Indicator . . . . .
Oil Change Indicator, Reset .
Oil, Engine
Capacity . . . . . . . . .
Recommendation . . . .
Viscosity . . . . . . . . .
Outlet
Power . . . . . . . . . . .
Overheating, Engine . . . . .
. . . . .98
. . . . .98
. . . .111
. . . .111
. . . .111
. . . . .85
. . . . .98
Phone (Uconnect®) . . . . . . . . . .76
Placard, Tire and Loading
Information. . . . . . . . . . . . .123
Power
Inverter . . . . . . . . . . . . . . .84
Outlet (Auxiliary Electrical
Outlet) . . . . . . . . . . . . . . .85
Preparation for Jacking. . . . . . . .100
Programmable Electronic Features. . .83
Rain Sensitive Wiper System . .
Rear Seat, Folding . . . . . . . .
Recreational Towing . . . . . . .
Shifting into Transfer Case
Neutral (N) . . . . . . . . . .
Shifting out of Transfer Case
Neutral (N) . . . . . . . . . .
Remote Starting System . . . . .
Replacement Bulbs. . . . . . . .
Reporting Safety Defects. . . . .
. . .22
. . .17
. . .90
. . .91
.
.
.
.
. .91
. .10
.124
.126
Schedule, Maintenance . . . . . . .113
Seat Belts . . . . . . . . . . . . . . . .11
Seats. . . . . . . . . . . . . . . . . . .15
Adjustment . . . . . . . . . . . .15
Easy Entry . . . . . . . . . . . . .16
Heated . . . . . . . . . . . . . . .19
Rear Folding . . . . . . . . . . . .17
Shifting
Transfer Case, Shifting into
Transfer Case Neutral (N) . . . .91
Transfer Case, Shifting out of
Transfer Case Neutral (N) . . . .91
Shift Lever Override . . . . . . . . .106
Signals, Turn . . . . . . . . . . . . . .22
Spare Tire . . . . . . . . . . . . . . . .99
Speed Control (Cruise Control) . . . .23
Starting
Remote . . . . . . . . . . . . . . .10
Steering
Tilt Column . . . . . . . . . . . .18
Steering Wheel Audio Controls . . . .75
Stuck, Freeing. . . . . . . . . . . . .107
Supplemental Restraint System Airbag . . . . . . . . . . . . . . . .12
Sway Bar Disconnect, Electronic . . .87
Temperature Control,
Automatic (ATC) . . . .
Theft System Arming. . .
Theft System Disarming .
Tilt Steering Column . . .
Tires
Air Pressure . . . . .
Changing . . . . . . .
Jacking . . . . . . . .
Spare Tire . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.25
.11
.11
.18
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.123
. .99
. .99
. .99
129
INDEX
Tow Hooks, Emergency . . . .
Towing . . . . . . . . . . . . .
Disabled Vehicle . . . . .
Recreational . . . . . . .
Trailer Towing
Trailer and Tongue Weight
Trailer Weight . . . . . . . . .
Turn Signals. . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.106
. .88
.107
. .90
. . . .88
. . . . .88
. . . . .22
Uconnect® Phone . . . . . . . . . . .76
Uconnect® Voice Command . . . . . .79
Voice Command . . . . . . . . . . . .79
130
Voice Prompt Volume
Navigation . . . . . . . . . . .57, 67
Volume
Navigation Voice Prompt . . .57, 67
Warning Lights . . . . . . . .
Washer
Rear . . . . . . . . . . .
Washers, Windshield . . . . .
Wheel and Wheel Trim Care .
Windshield Washers . . . . .
Windshield Wipers . . . . . .
Wiper, Rear . . . . . . . . . .
. . . . .94
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .22
. .22
.124
. .22
. .22
. .22
FAQ (How To?)
FREQUENTLY ASKED QUESTIONS
GETTING STARTED
• How do I install my LATCH Equipped Child Seat? pg. 13
• How do I adjust the height of my Front Seat? pg. 15
OPERATING YOUR VEHICLE
• How do I operate my Soft Top? pg. 26
• How do I operate my Hard Top? pg. 35
ELECTRONICS
• Which radio is in my vehicle?
• Uconnect® 130 pg. 42
• Uconnect® 130 WITH SiriusXM™ pg. 44
• Uconnect® 230 pg. 47
• Uconnect® 430/430N pg. 50
• Uconnect® 730N pg. 60
• How do I activate the Audio Jack?
• Uconnect® 130 pg. 49
• Uconnect® 130 WITH SiriusXM™ pg. 49
• Uconnect® 230 pg. 49
• Uconnect® 430/430N pg. 54
• Uconnect® 730N pg. 63
• How do I set the clock on my radio?
• Uconnect® 130 pg. 42
• Uconnect® 130 WITH SiriusXM™ pg. 42
• Uconnect® 230 pg. 42
• Uconnect® 430/430N pg. 50
• Uconnect® 730N pg. 60
• How do I use the Navigation feature?
• Uconnect® 430/430N pg. 56
• Uconnect® 730N pg. 67
• How do I pair my cell phone via Bluetooth® with the Uconnect® Phone Hands-Free
Voice Activation System? pg. 76
• How do I use my iPod®? pg. 75
• How do I use my USB port to listen to audio through my touch-screen radio? pg. 75
131
FAQ (How To?)
OFF-ROAD CAPABILITIES
• How do I shift into different four-wheel drive selections? pg. 86
UTILITY
• How do I know how much I can tow with my Jeep Wrangler? pg. 88
WHAT TO DO IN EMERGENCIES
• What do I do if my TPMS warning light is blinking? pg. 94
• How do I change a flat tire? pg. 99
• How do I Jump-Start my vehicle? pg. 104
MAINTAINING YOUR VEHICLE
• Where is my Fuse Block located? pg. 119
• What type of oil do I use? pg. 111
• How often should I change my engine’s oil? pg. 113
• What should my tire pressure be set at? pg. 123
132
NOTES
133
NOTES
134
NOTES
135
NOTES
136
This guide has been prepared to help you get quickly
acquainted with your new Jeep and to provide a convenient
reference source for common questions. However, it is not a
substitute for your Owner’s Manual.
For complete operational instructions, maintenance procedures
and important safety messages, please consult your Owner’s
Manual, Navigation/Uconnect® Manuals and other Warning
Labels in your vehicle.
Not all features shown in this guide may apply to your vehicle.
For additional information on accessories to help personalize
your vehicle, visit www.mopar.com or your local Jeep dealer.
Driving and Alcohol:
Drunken driving is one of the most frequent causes of collisions. Your
driving ability can be seriously impaired with blood alcohol levels far below
the legal minimum. If you are drinking, don’t drive. Ride with a designated
non-drinking driver, call a cab, a friend, or use public transportation.
WA R N I N G !
Driving after drinking can lead to a collision. Your perceptions are
less sharp, your reflexes are slower, and your judgment is impaired
when you have been drinking. Never drink and then drive.
Jeep.com
Download a free
Vehicle Information
App by visiting your
application store, Keyword
(Jeep Vehicle Info), or
scanning the Microsoft Tag.
To put Microsoft Tags to
work for you, use your
Get the free mobile app for your phone
http://gettag.mobi
mobile phone’s browser or App
store to download a
Microsoft Tag reader, like the free one at www.gettag.mobi.
Then follow the directions to scan the code.
Download a FREE electronic copy
of the Owner’s Manual or Warranty Booklet by
visiting the Owners tab at:
www.Jeep.com (U.S.) or
www.Jeep.ca (Canada).
13JK72-926-AA
Wrangler
Second Edition
User Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising