Catalogue Sheet: Ultima™ Battery Series

Catalogue Sheet: Ultima™ Battery Series
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
TYPICAL SPECIFICATIONS
ULTIMA™ SERIES
Thermoplastic, 6 and 12V
FEATURES
• Designed with aesthetics, ease of
installation and performance in mind
• Simple, compact and contemporary
design
• Wall-mount, ceiling-mount flat or
pendant installation
• Two-piece housing of injection molded
thermoplastic
• Two MR16 halogen lamps, shielded
by clear polycarbonate covers
• Available with long lasting MR16 LED
lamps
• Sealed, maintenance-free,
Lead-Calcium battery
• Dual voltage input: 120/347VAC
• Up to 150W of total battery capacity
• Auto-diagnostics (optional)
• NEXUS® interface (optional)
• Certified CSA 22.2 No.141
Supply and install the Ready-Lite® Ultima™ Series battery unit equipment. The unit construction shall include
a housing and a front cover of high-impact thermoplastic moulded in white. No screws shall be necessary to
hold the front cover to the housing. The unit shall be equipped with two emergency heads with adjustable
swivels and MR-16 lamps of
V
W protected by snap-on shock-absorbent, clear polycarbonate
covers. The unit shall be suitable for wall mount or as otherwise specified. The unit equipment shall have a
dual-voltage input of 120/347VAC and shall be equipped with a test switch and a green pilot light, located
on the left side.
The housing shall host the battery and the battery charger. The battery charger and other unit functions shall
be driven by a micro-controller. All electronic circuitry shall be installed on a single printed circuit board.
When specified, the unit equipped with auto-test shall automatically self-test for one minute every 30 days,
10 minutes every 6 months and 30 minutes annually. When a fault is detected, the bi-colour pilot light shall
turn from green to red and start flashing. A legend on a label next to the pilot light shall display the source of
failure: battery, charger circuitry or lamp load.
The unit equipment shall be listed to the standard CSA 22.2 No.141.
The unit equipment shall be Ready-Lite® model:
.
WIRE GUARDS
460.0080-RL
wall mount or ceiling mount
REPLACEMENT LAMPS
ORDERING CODE
LAMP TYPE
580.0079-RL
MR16 halogen
VOLTAGE/ WATTAGE
6V-10W
580.0080-RL
MR16 halogen
12V-12W
580.0064-RL
MR16 halogen
12V-20W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
30MIN
640
40
672
WATTAGE CAPACITY
1H00
1H30
2H00
4H00
23
16
12
-
72
42
30
24
12
80
44
32
26
13
12120
120
70
50
40
20
12150
150
84
60
48
24
1280
120/347VAC
0.25 / 0.09 A
U L T I M A ™ FA M I LY
Ultima™ Exit P. 53
Ultima™ Combo P. 56-57
122
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
DIMENSIONS
Dimensions are approximate and subject to change.
ULTIMA™ SERIES
12-1/4” [31.0 cm]
10-5/8” [26.9 cm]
Thermoplastic, 6 and 12V
3-7/8” [9.8 cm]
ORDERING INFORMATION
SERIES
CAPACITY
ULT6= 6V
40= 40W
72= 72W
ULT12= 12V
80= 80W
120= 120W
150= 150W
UNIT TYPE
HEADS
Blank= standard
0= no
AD= auto-diagnostic*
heads
ADN= auto-diagnostic, non-audible*
2= two
®
NEX= NEXUS system interface*
heads
NEXRF= wireless NEXUS® system interface*
LAMPS
COLOUR
VOLTAGE
LD1= MR16 LED, 6V-4W
W= factory Blank= 120/347VAC
LD7= MR16 LED, 12V-4W
white 2= 120/277VAC
LD9= MR16 LED, 12V-5W
B= black
LD10= MR16 LED, 12V-6W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
*Minimum lamp load required: 20% of unit
capacity
*Not all options available with NEXUS® System.
Please consult your sales representative
E X A M P L E : U LT 6 4 0 2 R M 6 W
123
OPTIONS
Blank= no options
CM= ceiling mount
D3= time delay
(15 mins.)
LC= line cord (120V)
PM= p
endant mount
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement