Elan | THP650LS | Installation manual | Elan THP650LS Installation manual

Elan THP650LS Installation manual
ELAN HOME SYSTEMS
INSTALLATION MANUAL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THP1200SW
WARNING:
To reduce the risk of fire or shock, do not expose
this appliance to rain or moisture.
CAUTION:
The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids
such as vases, shall be placed on the apparatus.
*Note: This product is for indoor use only.
The lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instruction in the literature accompanying
the product.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blades or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
© ELAN Home Systems 2005 • All rights reserved.
Page 1
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Contents
Introduction ....................................................................... 4-6
Specifications ........................................................................ 4
Features .................................................................................. 5
THP1200SW Rear Panel ......................................................... 6
Installation ....................................................................... 7-10
Wiring ...................................................................................... 7
Connections ........................................................................... 9
Controls/Adjustments ...............................................11-12
Troubleshooting ................................................................ 13
Applications ....................................................................14-27
Stereo .................................................................................... 14
Home Theater ........................................................................ 16
Limited Warranty ................................................ Back Page
Page 2
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
Introduction
Congratulations and thank you for purchasing ELAN TheaterPoint
speakers. The TheaterPoint speaker line is designed specifically to
match the needs of dedicated Home Theater and critical listening
areas within the home. Using state-of-the-art materials like woven
Kevlar fiber cones, neodymium magnets, and aluminum phase plugs,
each speaker seamlessly reproduces movie soundtracks and music
with the clarity and precision demanded in today’s multi-channel
environments. Advanced features such as three-way EQ switches,
bass limiting circuits, custom Q crossovers, and pivoting tweeters allow flexibility and customization for virtually any circumstance where
accurate audio reproduction is paramount.
TheaterPoint speakers are designed as a family. Each speaker complements the others. All use similar components to create a coherent
audio experience no matter what the content. These speakers are
also designed to provide custom solutions for virtually any multi-room
environment. In-wall, in-ceiling, on-wall, and free-standing speakers
combine to create the exact setup each home requires. No matter
which combination is appropriate, TheaterPoint speakers provide
sonic accuracy and reproduce all audio sources to ELAN’s exacting
standards.
Specifications
System Type .................................................. 12" Powered Subwoofer
Woofer
Cone ................................... 12" 3 Layer Honeycomb Composite (Kevlar
Composite/Aluminium Honeycomb/Kevlar Composite)
Magnet ........................... Double Magnet Assembly/Vented Spider & Pole
........................................................... Half-Roll Butyl Rubber
Voice Coil .................................................................... 2.5" Fiberglass
Basket ........................................................................ Cast Aluminum
Crossover ..........Continuously Variable from 50-150Hz, 24dB/Octave Slope
Power ................................................................................. 300 Watts
Frequency Response ................................................ 22Hz to 150Hz
Power Requirements ................................. 115V~/60Hz - 230V~/50Hz
Dimensions
Surround
W/H/D ................................................................. 15 3/4" W X 15 3/4" D X 17" H
(400mm x 400mm x 432mm)
Weight .................................................................................... 56.8 lbs. (25.76kg)
Shipping Weight ........................................................................ 64 lbs. (29.03kg)
© ELAN Home Systems 2005 • All rights reserved.
Page 3
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Features
• 3 Layer Honeycomb Composite Driver
• 300 Watt Class D Amplifier
• Cast Aluminum Basket
• 24dB/Octave Continuously Variable Low-Pass
Crossover
• Low-Level Line Outputs Hi-Pass Filtered
at 80Hz,12dB/Octave
• Butyl Rubber Surround
• 180 Degree Variable Phase Control
• Tuned, Complimentary 30Hz High-Pass Filter
• Dedicated LFE (Low Frequency Effect) Input
• Line-Level & Speaker Level Inputs/Outputs
• Gloss Black Cabinet
Page 4
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
THP1200SW Rear Panel
Speaker Level
Outputs
Speaker Level
Inputs
Line Level Line Level
Inputs
Outputs
LFE
Input
Frequency
Control
(Crossover)
Volume
Control
Phase
Control
Auto/On
Switch
Power
LED
Power
Switch
AC Power
Plug
Fuse
Cover
120V
230V/115V
Switch
© ELAN Home Systems 2005 • All rights reserved.
Page 5
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Installation
After carefully considering the intended application (defining a
Listening Area, Home Theater/Stereo, etc.), specific mounting
locations can be decided upon. Once the specific locations are
determined, installation can commence.
Wiring
Before actually running any wire or cable, take the time to look around
each room or area of the house and plan your wire paths for maximum efficiency. Look for routes through uncluttered parts of the stud
wall or ceiling that allow you to group all low-voltage wires wherever
possible. It is a good practice to label both ends of all cables and to
protect wires by tying a plastic bag over the ends.
Note: Run low voltage wiring in accordance with the National Electrical Code as well as any other applicable provisions of the local building codes in your area. In some cases (such as commercial installations), running the wire in conduit may be required. If you have
any questions concerning the wiring of speakers in your home, contact your local building and inspection department.
Decide what type of connections will be utilized for the subwoofer(s)
prior to prewire. The THP1200SW can be configured to run line level
(RCA cables), or speaker level (speaker wire) but NOT BOTH.
Speaker Level
Speaker level pre-wiring consists of running speaker wire through
walls and using speaker wall plates at termination points. Use 1216AWG stranded speaker wire and be sure to observe proper polarity.
Rear
Rear
Bannana
Plug
Bannana
Plug
12-16 AWG
Stranded
Speaker Wire
To
THP1200SW
SPK IN
Front
Page 6
Bannana
Plug
Bannana
Plug
Speaker
Wall Plates
To
Home Theater
Receiver
SPK OUT
Front
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
Wiring (cont’d)
Line Level
When the sub is in close proximity to the Home Theater Receiver, it
is often easiest to use a pre-made subwoofer cable plugged directly
between the receiver and the subwoofer. If the sub is to be installed
in an area that is distant from the receiver and/or there are no provisions to hide a cable run, use RG-6 coaxial cable to run through the
walls. Use coaxial wall plates as termination points in the walls. Use
F-to-RCA adapters at the wall plates and use short RCA cables to run
from the wall plate to the subwoofer and receiver.
Rear
Rear
RG-6 Coaxial
Cable
RCA
Subwoofer
Cable
F-to-RCA
Adaptor
To
THP1200SW
LFE IN
Front
F-to-RCA
Adaptor
Coaxial
Wall Plates
Front
© ELAN Home Systems 2005 • All rights reserved.
RCA
Subwoofer
Cable
To
Home Theater
Receiver
LFE OUT
Page 7
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Connections
AC Power
The THP1200SW is an active, powered subwoofer, meaning that it
must be plugged into a nearby AC outlet to power the built-in amplifier. Avoid extremely long extension cords and be sure the AC circuit
being utilized can support the current draw of the subwoofer
(~ 3 Amps). The power switch should be in the OFF position and the
power cord should be unplugged before making any connections or
moving the unit.
Line-Level Connections
The THP1200SW has line-level RCA inputs. In typical installations,
the LFE (Low Frequency Effects) output of a Home Theater Receiver
is connected to these inputs using an RCA subwoofer cable as shown
below. Use RG-6 coaxial cable with F-to-RCA adapters to extend
wires through walls.
Overview
THP650LS
A/V Receiver
LFE
(RCA Cable)
Speaker Wire
A/V Receiver w/ LFE Output
THP1200SW
Line-Level Inputs
A/V Receiver 5.1 Outputs
Front Left
Rear Left
Front Right
Rear Right
Center
LFE
RCA
Subwoofer
Cable
A/V Receiver w/Out LFE Output
A/V Receiver
Line-Level Outputs
AUX
IN
THP1200SW
Line-Level Inputs
AUX
OUT
L
R
RCA
Y Cable
Page 8
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
Speaker Level Connections
While it is preferable to use line-level connections when connecting
a subwoofer, sometimes it is necessary to use the provided speaker
level connections instead. Stereo applications where the receiver/
amp has no line-level output are frequently connected in this way.
THP650LS
A/V Receiver
Speaker Wire
Speaker Wire
Left
Speaker
Right
Speaker
A/V Receiver
Speaker Outputs
THP1200SW Rear
© ELAN Home Systems 2005 • All rights reserved.
Page 9
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Controls/Adjustments
230V/115V
Select the correct voltage setting for your area.
POWER
Place the POWER switch to the ON position to turn the subwoofer on.
Place it in the OFF position to turn it off.
AUTO/ON
In the ON position, the subwoofer remains powered up whenever the
POWER switch is on. In the AUTO position, the subwoofer powers up
when it receives a signal, then turns off after fifteen minutes of inactivity.
Setting VOLUME Level
Use the VOLUME control to adjust the volume level of the subwoofer
relative to the other speakers in the system. Experiment with different levels upon initial setup to acheive full, rich bass response without
“popping” or excess distortion. ELAN recommends starting the initial
setup process with the VOLUME control set to the midddle position
and adjusting to the desired level using source material with a prominent and repetitive bass line.
Setting FREQUENCY Control
The FREQUENCY control adjusts the upper frequency limit of sound
that is emanated from the subwoofer. This control is adjustable from
50 to 150Hz. Correctly setting the Frequency level is paramount to
a smooth transition between the main speakers and the subwoofer.
Setting this control too low causes a gap to occur in the audio that
makes the main speakers to seem disconnected from the bass, an
audible separation of sound that does not seem natural. Setting the
control too high causes bass frequencies to emanate too strongly
because of overlapping frequencies between the main speakers and
subwwoofer. This causes a “muddy” sound and reduces the overall
clarity of the audio.
It is important to experiment with the FREQUENCY control upon initial
setup to obtain the clearest, smoothest sound possible. After setting
the FREQUENCY control, go back and adjust the VOLUME control
again, in order to fine-tune the sound.
Page 10
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
Setting PHASE +/The PHASE Control is used to reverse the polarity (+/-) of the subwoofer in comparison to the other speakers in the system. In certain
situations, room acoustics can cancel bass waves coming from the
subwoofer.
To adjust PHASE, sit in the listening position and listen to a recording
with a prominent, steady bass line (Preferable the same track used for
the other adjustments). Place the PHASE switch in each position and
choose the one that provides the smoothest, clearest bass.
Replacing Fuses
If the subwoofer fails to power up (no POWER LED lit), it is possible
that the main fuse has blown. To replace the fuse, remove the Fuse
Cover (located just below the power plug), remove the fuse, and replace with a new one. For units utilizing 115V, replace with a T6.3AL/
250V (115V) glass fuse. For units utilizing 230V, replace with a
T3.15AL/250V glass fuse.
Remove
Fuse Cover
© ELAN Home Systems 2005 • All rights reserved.
Replace
Fuse
Page 11
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Troubleshooting
SYMPTOM
No Audio From
Subwoofer - Plays
OK from Other
Speakers - Power
LED OFF
No Audio From
Subwoofer - Plays
OK from Other
Speakers - Power
LED ON
Poor Audio Quality
Page 12
CAUSE
SOLUTION
Not Plugged In
Connect to AC Power
Unit Turned OFF
Turn Power Switch to ON
Position
Subwoofer Fuse Blown
Replace Fuse (See p. 12)
House Circuit Breaker
Tripped
Reset Breaker
Find Cause of Trip
VOLUME Set Too Low
Turn Up VOLUME Control
FREQUENCY Control
Set Too Low
Increase FREQUENCY
Control Setting
Incorrect Audio
Connections
Verify Audio Connections
(See p. 9-10)
VOLUME, FREQUENCY,
and/or PHASE Controls
Incorrectly Set
Adjust Controls Correctly
(See p. 11)
Incorrect A/V Receiver/
Amplifier Settings
Verify A/V Receiver/Amplifier
Settings (See A/V Receiver
Manual)
Subwoofer Placed
Incorrectly in Room
Correct Placement See
Subwoofer Positioning
p. 17
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
Applications
All TheaterPoint speakers have similar “voices” designed to work
together to create a seamless, high-quality Home Theater or critical listening experience. ELAN strongly recommends installing
TheaterPoint speakers in matched groups (Left, Center, Right, Rear,
Sub) in order to preserve the acoustic integrity of the source material.
The following section describes each TheaterPoint speaker in appropriate applications with other TheaterPoint speakers.
Stereo
Certain TheaterPoint speakers lend themselves very well to stereo
critical listening applications. Please keep in mind that a defined
stereo listening area must be present in order to acheive maximum
benefit from stereo placement.
THP525LS/THP650LS
THP650LS
or
THP525LS
THP650LS
or
THP525LS
THP525LS/THP650LS/THP1200SW
THP1200SW
Subwoofer
THP650LS
or
THP525LS
© ELAN Home Systems 2005 • All rights reserved.
THP650LS
or
THP525LS
Page 13
THP1200SW
INSTALLATION MANUAL
Stereo Applications (cont’d.)
ELAN HOME SYSTEMS
THP800C
Critcal listening areas require a well-defined listening position.
Make sure to point the speakers toward the listening area as shown.
THP800C
THP800C
X
THP800C/THP1200SW
Add a THP1200SW subwoofer to increase bass response. This
adds richness to the music and makes a huge improvement in
sound quality.
THP800C
THP800C
THP1200SW
Subwoofer
X
Page 14
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
Home Theater
It is essential to use voice-matched speakers in any Home Theater
application. Sound emanates from each speaker in turn, and all
should sound the same. TheaterPoint speakers satisfy this requirement perfectly, and should be used in combinations shown in the
following section.
Center Channel Positioning
A center channel speaker should be placed as close as possible to
the video display utilized in a Home Theater. In-wall center channel
speakers should be mounted immediately above or below the screen
as shown below. If using a cabinet speaker like ELAN’s THP525LS or
THP650LS as a center channel, position it on a stand immediately below the screen. A Center Channel speaker can also mount on a shelf
above the screen - possibly in a cabinet or entertainment center.
In-Wall Center Channel
In-Wall
Center Channel
TV
OR
TV
In-Wall
Center Channel
Cabinet Center Channel
Shelf
Cabinet
Center Channel
TV
OR
TV
Cabinet
Center Channel
Speaker
Stand
© ELAN Home Systems 2005 • All rights reserved.
Page 15
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Subwoofer Positioning
Subwoofers are considered to be omnidirectional. They produce low
bass frequencies that are not especially localized. The human ear
does not rely on these frequencies to place sounds in space therefore, placement is not as important as with other types of speakers.
Place subwoofers along the front wall of the room approximately 2-3
feet from the corners. Expect a 3-9dB bass boost if the subwoofer is
placed directly in the corner of a room (called “corner loading”). It is
usually not advisable to place subwoofers directly next to the seating
position in a Home Theater.
TV
2-3 Feet
THP1200SW
Subwoofer
Subwoofers May Be
Placed on Either
Side of Screen
X
THP1200SW
Subwoofer
Not
Recommended
Multiple Subwoofers
It is sometimes desirable to install multiple subwoofers for increased
bass response in a Home Theater. Place the subwoofers equal distance from the screen in similar locations as shown below.
TV
THP1200SW
Subwoofer
Page 16
THP1200SW
Subwoofer
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
5.1 Surround Sound Applications
THP525LS/THP650LS - Free-Standing L/C/R
THP650SS - On-Wall Dipole Rear Side
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP650LS
or
THP525LS
THP650LS
or
THP525LS
THP650LS
or
THP525LS
THP650SS
THP650SS
THP800C - In-Ceiling L/C/R & Rear
THP1200SW - Subwoofer
THP1200SW
Subwoofer
TV
THP800C
THP800C
THP800C
© ELAN Home Systems 2005 • All rights reserved.
THP800C
THP800C
Page 17
THP1200SW
INSTALLATION MANUAL
5.1 Applications (cont’d.)
ELAN HOME SYSTEMS
THP525W - In-Wall L/C/R
THP650D - In-Wall Dipole Rear Side
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP525W
THP525W
THP650D
THP525W
THP650D
THP650W - In-Wall L/C/R & Rear
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP650W
THP650W
THP650W
THP650W
Page 18
THP650W
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
THP650W - In-Wall Left/Right
THP525W - In-Wall Center
THP650D - In-Wall Dipole Rear Side
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP525W
THP650W
THP650W
THP650D
THP650D
THP525LS/THP650LS - Free-Standing L/C/R
THP650D - In-Wall Dipole Rear Side
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP650LS
or
THP525LS
THP650LS
or
THP525LS
THP650D
© ELAN Home Systems 2005 • All rights reserved.
THP650LS
or
THP525LS
THP650D
Page 19
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
THP525LS/THP650LS - Free-Standing L/C/R
THP800C - In-Ceiling Rear
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP650LS
or
THP525LS
THP650LS
or
THP525LS
THP800C
THP650LS
or
THP525LS
THP800C
THP650W - In-Wall L/C/R
THP800C - In-Ceiling Rear
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP650W
THP650W
THP650W
THP800C
Page 20
THP800C
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
5.1 Applications (cont’d.)
THP1200SW
THP525W - In-Wall L/C/R
THP800C - In-Ceiling Rear
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP525W
THP525W
THP525W
THP800C
THP800C
THP525W - In-Wall Center
THP650W - In-Wall L/R
THP800C - In-Ceiling Rear
THP1200SW - Subwoofer
TV
THP1200SW
Subwoofer
THP525W
THP650W
THP650W
THP800C
THP800C
© ELAN Home Systems 2005 • All rights reserved.
Page 21
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
6.1/7.1 Surround Sound
6.1 and 7.1 surround sound systems utilize additional rear and/or rear
side speakers to enhance the audio effects contained in a soundtrack.
Any of the previous examples can easily become a 6.1 or 7.1 system
by changing the configuration of the rear channels. The diagrams in
this section show rear and side rear speakers only!
6.1 Systems
Typical 6.1 systems use two rear side speakers with a center
rear speaker. Several logical combinations can be created using
TheaterPoint speakers as shown in the following examples.
THP800C - In-Ceiling Rear
THP800C
THP800C
THP800C
THP650D - In-Wall Rear Side
THP525W - In-Wall Rear Center
THP650D
THP525W
THP650D
THP650SS - On-Wall Rear Side
THP525W - On-Wall Rear Center
THP650SS
THP650SS
THP650LS
Page 22
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
6.1 Applications (cont’d.)
THP1200SW
THP650W - In-Wall Rear
THP650W
THP650W
THP650W
THP525W - In-Wall Rear
THP525W
THP525W
THP525W
THP525W - In-Wall Rear Center
THP650D - In-Wall Rear Side
THP650D
THP650D
THP525W
© ELAN Home Systems 2005 • All rights reserved.
Page 23
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
7.1 Systems
Use a total of four speakers for rear Surround effects when configuring 7.1 systems. Several logical combinations can be created using
TheaterPoint speakers as shown in the following examples.
THP800C - In-Ceiling Rear and Rear Side
THP800C
THP800C
THP800C
THP800C
THP650D - In-Wall Rear Side Speakers
THP650W - In-Wall Rear Speakers
THP650D
THP650D
THP525W
THP525W
THP650SS - On-Wall Rear Side
THP650LS - On-Wall Rear
THP650SS
THP650SS
THP650LS
Page 24
THP650LS
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
7.1 Applications (cont’d.)
THP650W - In-Wall Rear and Side
THP650W
THP650W
THP650W
THP650W
THP525W - In-Wall Rear and Rear Side
THP525W
THP525W
THP525W
THP525W
THP650D - In-Wall Rear Side
THP525W - In-Wall Rear
THP650D
THP650D
THP525W
THP525W
© ELAN Home Systems 2005 • All rights reserved.
Page 25
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
High Performance 7.1 Surround System
THP650LS - Free-Standing L/C/R
THP650SS - On-Wall Rear Side
THP525LS - On-Wall Rear
THP1200SW - Subwoofers
TV
THP1200SW
Subwoofer
THP1200SW
Subwoofer
THP650LS
THP650LS
THP650LS
THP650SS
THP650SS
THP525LS
Page 26
THP525LS
© ELAN Home Systems 2005 • All rights reserved.
ELAN HOME SYSTEMS
INSTALLATION MANUAL
THP1200SW
Notes:
© ELAN Home Systems 2005 • All rights reserved.
Page 27
THP1200SW
INSTALLATION MANUAL
ELAN HOME SYSTEMS
Notes:
Page 28
© ELAN Home Systems 2005 • All rights reserved.
Limited Warranty
ELAN HOME SYSTEMS L.L.C. (“ELAN”) warrants the THP1200SW
subwoofer to be free from defects in materials and workmanship
for the period of two years (2 years) from date of purchase. If within
the applicable warranty period above purchaser discovers that
such item was not as warranted above and promptly notifies ELAN
in writing, ELAN shall repair or replace the item at the company’s
option. This warranty shall not apply (a) to equipment not manufactured by ELAN, (b) to equipment which shall have been installed by
other than an ELAN authorized installer, (c) to installed equipment
which is not installed to ELAN’s specifications, (d) to equipment
which shall have been repaired or altered by others than ELAN,
(e) to equipment which shall have been subjected to negligence,
accident, or damage by circumstances beyond ELAN’s control, including, but not limited to, lightning, flood, electrical surge, tornado,
earthquake, or other catastrophic events beyond ELAN’s control,
or to improper operation, maintenance or storage, or to other than
normal use of service. With respect to equipment sold by, but not
manufactured by ELAN, the warranty obligations of ELAN shall in all
respects conform to the warranty actually extended to ELAN by its
supplier. The foregoing warranties do not cover reimbursement for
labor, transportation, removal, installation or other expenses which
may be incurred in connection with repair or replacement.
Except as may be expressly provided and authorized in writing by
ELAN, ELAN shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured by ELAN
or services rendered by ELAN.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER EXPRESSED AND IMPLIED WARRANTIES EXCEPT
WARRANTIES OF TITLE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
ATTENTION: TO OUR VALUED CONSUMERS
To ensure that consumers obtain quality pre-sale and after-sale
support and service, ELAN Home Systems products are sold exclusively through authorized dealers. ELAN products are not sold
online. The warranties on ELAN products are NOT VALID if the
products have been purchased from an unauthorized dealer or an
online E-tailer. To determine if your ELAN reseller is authorized,
please call ELAN Home Systems at (859) 269-7760.
P/N9900720 REV:D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising