Yamaha MJ100 Owner's manual
 YAMAHA
MIXER
NA II IDO
OPERATING MANUAL
YAMAHA
SS ле
MIC
20
vu
A
10 7 53 0) 4
[
POWER
>
Le
ето нм @ 0
BOO wom om
K
GRAPHIC EQUALIZER
9 91 =
- 3
— 5 5 —
h— 4
— 3
—2
— |
|
==
SOURCE 1
CROSS FADER
©
10
PHONES
SOURCE
1
cl pity
SOURCE
2
SOURCE
142
CJ
MIC
fl
С
INST
MAS
10 1 о 1
AUX , SEND RETURN
-
® - am O
SHORT MID LONG
L A DELAY TIME © 10
PAN REGENERATION
gr Y Fr —
— 18 10 —
э — —— в — — 9 —
pm Bim — 1 — 4
7 ——4 7 PA
— 5 — — 6 —
| & — + -— 5
1 — | ‹ — H— 4 —
3 — — — Fi
2 — + — 2 — HH 2 —
1 — | 1 — — 1 —
E 0
a — — eee
SOURCE 2 MIC INST LINE QUT MASTER
С с
a ON OFF a Oh OFF
MIC
Y
PHONES
Y
ce
MONITOR
SELECT
Thank you for purchasing the Yamaha MJ100 Mixer. In order to take full
advantage of the MJ100's capabilities and to enjoy long, trouble-free op-
eration, please read this manual before use, and keep it in a safe place with
the warranty for later reference.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
FEATURES
@ Five-band +/— 12dB Graphic Equalizer allows you
to adjust the sound to suit any location or speaker
system.
Built-in RIAA phono equalizer for directly con-
necting record players.
Phantom power for 4P-type condensor micro-
phone.
Built-in three mode delay (short, mid, long) for
creative sounds. |
Monitor select switches allow you to check input
or output through a set of headphones.
O Explanation of Graphical Symbois
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated "dangerous voltage” within
the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CONTENTS
PRECAUTIONS
@ Location
Using the product in the following types of location
may cause malfunction and damage the product.
© In direct sunlight or near a heater
e In extremely cold locations
e In excessive dust or humidity
e Where the unit will be subjected to excessive
vibration
Handling
Strong physical shocks to the unit can cause
damage. Handie it with care. Do not apply ex-
cessive force to the switches or controls.
Power Cable
To prevent shorting or damaging the power cable,
grasp the connector—not the cable—when unplug-
ging it. When you will not be using the unit for an
extended period of time, unplug the power cable
from the AC power source.
Power Source
Make sure that the power source voltage specified
on the rear panel matches your local AC power
supply.
Moving the Unit
To prevent short circuits or cable damage, unplug
all cables before moving the unit.
Connections
Before connecting the MJ100 with other units, turn
the power of all units OFF and turn the MJ100
master volume ali the way down.
Do Not Open the Unit
This product contains no user-servicable parts.
Refer all maintenance to qualified YAMAHA ser-
vice personnel. Opening the unit and/or tampering
with the internal circuitry will void the warranty.
Cleaning
Never use solvents such as benzine or thinner to
clean the unit, and do not use aerosol-type sprays
nearby. Wipe the unit clean with a soft, dry cloth.
Electrical Storms
In the event of an electrical storm (lightning)
nearby, unplug the power cable from the AC power
source.
Warranty
When purchasing the unit, be sure to fill out the
warranty, and have it stamped by the dealer. If you
fail to do so, you may be charged for repair service
performed even within the warranty period.
SAFETY INSTRUCTIONS (PREPARED IN ACCORDANCE WITH UL STANDARD 1270)
Read Instructions — All the safety and operating instructions
should be read before the appliance is operated.
Retain Instructions — The safety and operating instructions
shouid be retained for future reference.
Heed Warnings — All warnings on the appliance and in the op-
erating instructions should be adhered to.
Follow Instructions — All operating and use instructions should
be followed.
Water and Moisture — The appliance should not be used near
water — for example, near a bathtub, washbowil, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, and
the like.
Carts and Stands — The appliance should be used only with a
cart or stand that is recommended by the manufacturer.
Wali or Ceiling Mounting — The appliance should be mounted
to a wail or ceiling only as recommended by the manufacturer.
Ventilation — The appliance should be situated so that its lo-
cation or position does not interfere with its proper ventilation.
For example, the appliance should not be situated on a bed,
sofa, rug, or similar surface that may block the ventilation
openings; or placed in a built-in installation, such as a bookcase
or cabinet that may impede the flow of air through the ventilation
openings.
Heat— The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
Power Sources — The appliance should be connected to a power
supply only of the type described in the operating instructions
or as marked on the appliance.
11.
12.
13.
14.
15.
16.
Power-Cord Protection — Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or againstthem, paying particular attention to cords
at plugs, convenience receptacies, and the point where they
exit from the appliance.
Cleaning — The appliance should be cleaned only as recom-
mended by the manufacturer.
Nonuse Periods — The power cord of the appliance should be
unplugged from the outlet when left unused for a long period
of time.
Object and Liquid Entry — Care should be taken so that objects
do not fall and liquids are not spilied into the enclosure through
openings.
Damage Requiring Service — The appliance should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the
appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or
exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure dam-
aged.
Servicing — The user should not attempt to service the appliance
beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
CONTROL PANEL
<
YAMAHA
MIXER
ЛС
+ 12
9
6
3
0
3
6
9
12
106 400 1K 3K 8K
GRAPHIC EQUALIZER
© = NW oa сл оч ое «a
Input Section >
O MIC jack
o
Special mic input for use with a goose neck con-
densor mic MJM-10 (option).
MIC jack
Normal mic input for use with standard phone plug
type.
Note) When both mic inputs 1 and 2 are used,
input 2 has priority. (The mic connected to
input 1 will not be used.)
MIC fader
This adjusts the level of the mic connected to input
1 or 2. Use this control to balance the mic with the
other input channels.
ON/OFF switch
This switches the mic on/off, allowing you to turn
the mic off without changing the fader level.
© == NW осо чо © ©
0 10 0 10
SEND RETURN
SHORT MID LONG
DELAY TIME 10
REGENERATION PHONES
SOURCE
1
SOURCE
2
SOURCE
1&2
© — г © во N +4 æ 0
MONITOR
SELECT
PHONES
у
© PAN control (mic pan)
The PAN control adjusts the mic signal in the stereo
field of the LINE OUT signal. Rotate PAN to the Те!
(or right) to place the signal toward the left (or right)
of the stereo field. In the center position, the mic
sound will be in the center of the stereo field.
AUX control (mic effect)
The AUX control adjusts the signal sent from the
mic to the internal delay circuit or the rear panel
AUX SEND. When an effects device is connected
between AUX SEND and AUX RETURN, the front
panel AUX will regulate the depth of the effect. The
level increases as you rotate AUX to the right.
@ INST fader
The INST fader adjusts the level of electronic or
electric instruments connected to the rear panel
INST L, R inputs. Both L and R inputs will be con-
trolled together. Use this control to balance the
INST input with the other input channels.
O ON/OFF switch
This switches the INST inputs on/off, aliowing you
to turn off the input without changing the fader level.
Both L and R inputs will be turned on/off together.
© AUX control (inst effect)
The AUX control adjusts the signal sent from the
INST inputs to the internal delay circuit or the rear
panel AUX SEND. The L and R signals will be
mixed. You cannot send only L or only R. When
an effects device is connected between AUX SEND
and AUX RETURN, the front panel AUX control will
regulate the depth of the effect.
The level will increase as you rotate AUX to the
right.
Ф ‚Ф.Ф. ® INPUT SELECT switches
These switches select the sources connected to the
rear panel SOURCE 1 and SOURCE 2 inputs. Press
the switch to select the corresponding source.
® , ® SOURCE 1, 2 faders
These adjust the level of the input sources selected
by the Input Select switches. A single fader controls
both L and R. Use these faders to balance the
SOURCE 1 and 2 inputs with the other input chan-
nels.
M CROSS FADER
This fader adjusts the balance between SOURCE
1 and SOURCE 2, as follows.
e As the CROSS FADER is moved to the left,
SOURCE 1 becomes louder and SOURCE 2 be-
comes softer.
® When the CROSS FADER is in the center posi-
tion, SOURCE 1 and 2 are the same level.
® As the CROSS FADER is moved to the right,
SOURCE 1 becomes softer and SOURCE 2 be-
comes louder.
< Master Section >
@ 5-BAND GRAPHIC EQUALIZER
This is a graphic equalizer with center frequencies
at 100Hz, 400Hz, 1kHz, 3kHz and 8kHz, with
+/—12dB of control over each band. Moving a
slider in the plus (+) direction will emphasize that
frequency range. Moving a slider in the minus (—)
direction will de-emphasize that frequency range.
When the slider is at 0, the response is flat. Adjust
equalizer settings to suit the room or speaker
system you are using. The equalized signal is sent
only from the MASTER OUT L, R jacks. Each slider
of the equalizer affects both channels L and R in
the same way.
® MASTER fader
The MASTER fader regulates the level output from
the rear panel MASTER OUT L, R jacks. It controls
the final volume (channels L and R together) of the
mixed input sources. Adjust the MASTER fader
level according to the VU meters (D, @ ).
O , 20) Output VU meters
These meters indicate the level of the signal output
from the rear panel MASTER OUT L and R jacks.
The levels will depend on the MASTER fader set-
ting. Adjust thee MASTER fader @& so that the
loudest signal makes the meters indicate 0dB.
@ LINE OUT fader
The LINE OUT fader regulates the level output from
the rear panel LINE OUT L, R jacks. It controls the
final volume (channels L and R together) of the
mixed input sources sent from the LINE OUT jacks.
Y) DELAY TIME select switch
The MJ100 has a built-in delay unit. When the rear
panel AUX RETURN jacks are not being used, a
Long, Mid or Short delay can be selected.
(E) REGENERATION control
When the rear panel AUX RETURN jacks are not
being used, the REGENERATION control regulates
the amount of signal sent to the built-in delay unit.
Use REGENERATION together with @ RETURN
to adjust the amount of delay effect. When the
RETURN control is at 0, there will be no delay effect.
The built-in delay unit can be used only by the MIC
and INST inputs.
Note) If an effects device is connected to the rear
panel AUX RETURN inputs, the built-in
delay unit will not operate, and @ and Y
will have no effect.
a SEND control
The SEND control regulates the level of the signal
output from the rear panel AUX SEND jack. When
using an external effects unit, this control regulates
“the level of the signal sent to the external effects
unit. Only the MIC and INST inputs can senda
signal through the SEND control to the rear panel
AUX SEND jack.
@ RETURN control
The RETURN control regulates the level of the
signal received from the rear panel AUX RETURN
inputs. When an external effects device is con-
nected, this control regulates the level of the signal
received from the external effects unit. If nothing
is connected to the AUX RETURN jacks, this control
regulates the level of the signal from the built-in
delay unit.
@) MONITOR SELECT switches
These switches select the signal to be monitored
in the headphones. The monitor signal is selected
as follows.
® SOURCE 1 & 2... The Selected Source 1 mixed
(L +R) signal input the left channel, and Selected
Source 2 mixed (L +R) signal input to the right
channel. All signals are before the source fader.
e MIC... The MIC signal input after the mic amp
but before the MIC fader. |
® INST ... The INST signal input before the INST
fader.
® MASTER OUT ... The mixed signal output from
the MASTER OUT jacks. Input signals are mon-
itored before the faders, and output signals are
monitored after the faders.
@) PHONES LEVEL control
The MONITOR LEVEL control regulates the level
of the headphone monitor signal. The headphone
will monitor the signal selected by the MONITOR
SELECT switches.
@) PHONES jack
Connect a pair of stereo headphones to this jack
to monitor the signal selected by @) and regulated
by @) .
@) POWER indicator
When the rear panel power switch is turned on, this
indicator will light.
REAR PANEL
<
MIXER MADE IN JAPAN
YAMAHA voce. MJIDO SER NO Г
YAMAHA CORPORATION
A
|
RISK OF ELECTRIC SHOCK . \
A ____DONOT OPEN o ®
ATTENTION RISQUE DE CHOC ELECTRIQUE. (
NE PAS QUVRIR
WARNING To REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
COMPLIES WITH THE LIMITS FOR A CLASS B
COMPUTING DEVICE PURSUANT TO SUBPART J
OF PART 15 OF FCC RULES.
Input Section >
30] PHONO inputs
@
®
Pin jack inputs for a record player. The MJ100 has
a built-in phono RIAA EQ amp, and record players
can be directly connected. Do not connect any other
type of equipment to these jacks.
AUX inputs
Line level pin jack inputs. Connect tuners or other
standard audio sources.
CD inputs
Line level pin jack inputs.
etc.
€ TAPE inputs
O
Line level pin jack inputs. Connect cassette or open
reel decks, etc.
INST inputs
Line level phone jack inputs. Connect electric or
electronic instruments, rhythm machines, etc.
GND
Connect the record player grounding wire to the
provided grounding terminal.
Connect CD players,
PHONO AUX со
<
O
©
Master Section >
MASTER OUT jacks
Output (standard phone jack) of the final mixed and
equalized signal. Connect these outputs to the
power amp system.
LINE OUT jacks
Output (PIN jack) of the mixed signals. Connect
these outputs to a recording deck, or (if using the
MJ100 as a submixer) to the main mixer.
AUX SEND jack
Output (standard phone jack) for when using an
external effect unit.
Connect this output to the input of the external effect
unit (reverb unit, delay unit, limiter, etc.).
AUX RETURN jacks
Inputs (standard phone jack) for when using an
external effect unit.
Connect the output of the external effect unit to
these inputs. When using these inputs, the MJ100's
built-in delay unit will not operate.
POWER switch
The power switch. When power is switched ON,
the front panel indicator @) will light. When power
is switched OFF, the indicator will go out.
SETUP EXAMPLE
e Basic setup
L Main speakers R
Power amp
[ЧЩ
‘Rhythm machine
т EA fr
rT = TT THT
RIT CT
! : |
7 (| voce
60000
if
MADE IN JAPAN
SER NO
YAMAHA voce. мало
120V 13W 60Hz -
YAMAHA CORPORATION
A | RISK OF ELECTRIC SHOCK |
/ _… DONCT OPEN 11 *
ATTENTION AISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
WARNING TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
COMPLIES WITH THE LIMITS FOR A CLASS B
OF PART 15 OF FCC RULE
5
COMPUTING DEVICE PURSUANT TO SUBPART J O
LES
LINE OUT
MASTER OÙT
© ©
— NS
e_ @ ©
= 00]
® CLT]
Tape deck
Record players
OUT
OUT L, R
Led.
TT TT
- 1 Posa GE
lazo,
oi
{| - cil
BORER I
Y eco
0 0060!
TT
| Веро
= | ©© |
© LI
e]
== |]
Tape deck
OUT
Tuner L,R LR
тете ен | 222 e |
[TIT >> >= = | =
E II 1 Y y Y Y UT EUR
== 0920000 CI G0
CD player
e Using the built-in delay unit
Control panel
SOURCE 1
\ | CROSS FADER
LINE GUT
MJM10 (Option)
Y
One or the other
Keyboard
Rear panel
AUX RTN — INSTY
R L R Ц
00 8 ó
5.0.0,00,0
00060
©
© ©
SOUR CE ==
РНОМО AUX TAPE
Dynamic mic
—
Stereo headphones
© Using an external effect unit
External effect unit
NE = OUT L
© Sex 3 | _e=
D
OUT R
YAMAHA fa TP
pozo . К. | wm | | | YAMAHA MODEL мод MADE IN aman _ MASTER OUT AUX BEND ux RTE INST г
КАР un 10. 1 | 120V 13W 60H PU
ree A - e J — YAMAHA CORPORATION (O) ©
en I — == Ni
RISK OF ELECTRIC SHOCK
DO NOT OPEN
| ети LINE OUT
POWER ton RISQUE DE CHOC ELECTRIQUE
WARNING 10 REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK [BO NOT EXPOSE THIS L GND U
APPLIANCE TO RAIN OF MOISTURE
COMPLIES WITH THE LIMITS FOR A LASS B © © ©
COMPUTING DEVICE PURSUANT TO SUBPART J
OF PART 15 OF FCC RULES A
ee
Stereo headphones
Dynamic mic
e Using the MJ100 as a submixer
YAMAHA MIXER MADE IN JAPAN (MASTER OUT AUX SEND AUX RTN INST ——
120V 13W 60Hz =
YAMAHA CORPORATION ee se © © © © © © ©
ON FF
. © ho! RISK OF ELECTRIC SHOCK
DO NOT OPEN
LINE OUT SOURCE Te
POWER ATTENTION RISQUE DE CHOC ELECTRIQUE. HONG AUX TAPE PHONO 6 TAE
WARNING 10 REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE THIS L (@
APPLIANCE TO RAIN OR MOISTURE
COMPLIES WITH THE LIMITS FOR A "CLASS B
COMPUTING DEVICE PURSUANT TO SUBPART J
OF PART 15 OF FCC RULES
LINE IN
== Km o ||
оО ООО ООО ООО SE
8139333335833 EEE
@ | ® | о | о | о | © е | © -
9100999009009 HEEE
QOD OOO TO OO OD
91010/0100 010'010|0!| © ©
elolojaja Pico] A C PB
elevlvia alu 0/0 /0/ обо
ООО ООО 6000
KL
MAIN MIXER
BLOCK DIAGRAM
ON/OFF y | FO]
MIC A BA SM © v | | MASTER
(—50) MIC FADER PAN OUT
ra
\
O Na MASTER
| | OUT
(0)
— п AUX
VE] 5
L UN
[ a: ON/OFF |
INST | |
: Bb
A Da or
FADER LINE
OUT
(— 10)
AUX
OR
De
. BA )
Ús, N
|
| |
| a
| sources _-7" ¢—{SUM>—y- > yn AUX SEND
, FADER | | SEND o | (—10)
!
A IN le
|
TN
| SHORT o
| MID ©
REGENERATION
№
| LONG O
CROSS FADER | DELAY TIME
!
{
|
>
LS
œ
>
nz“
|
|
1
PHONO © |
SOURCE? |
| ТАРЕ |
|
O— FADER |
RY [email protected]———o0 [7 > JE
=
©
=
or
2
m
À
5
z\5
> [| РОМ
(—22)
O
O ¡MONITOR
SELECT
PHONES
LEVEL
10
INPUT/OUTPUT SPECIFICATIONS
FREQUENCY RESPONSE +0, —3dB 20Hz ~ 20kHz
TOTAL HARMONIC DISTORTION (20Hz - 20kHz) Less than 0.1%
HUM & NOISE (20Hz ~ 20kHz) Rs = 150 ohms — 122 dB (EIN)
STEREO OUT Master fader and MIC fader at Maximum level — 88 dB
CROSSTALK (1kHz)
Adjacent Input — 60 dB
Input to Output — 60 dB
MAXIMUM VOLTAGE GAIN
PHONO IN to MASTER OUT 44 dB
PHONO IN to STEREO OUT 34 dB
AUX RETURN to STEREO OUT 10 dB
PHONO IN to AUX SEND 34 dB
INST IN to AUX SEND 10 dB
EQUALIZER (MASTER GEQ)
100, 400, 1K, 3K, 8K 5 BAND +12 dB Maximum
DIGITAL DELAY
SHORT MID LONG 3 Positions
(100ms) (150ms) (200ms)
POWER REQUIREMENTS
(US 8 Canadian models) AC120V, 60HZ
(General model) AC220, 240V, 50/60Hz
POWER CONSUMPTION | 13 W
DIMENSIONS (W x H x D) 350 x 77 x 254 mm
(13-3/4” x 3-1/4” x 10”)
WEIGHT 2.8 kg (6.2 Ib)
*
Hum 8 Noise are measured with edB/octave filter at 12.7kHz: equivalent to a 20kHz filter with infinite
dB/octave attenuation.
** 0dB is referenced to 0.775V rms.
11
INPUT CHARACTERISTICS
Actual Load Input Level
Connection Impedance For Use With Nominal Connector In Mixer
p Nominal Max. before clip
PHONO 47k ohms — 44 dB (4.9mV) — 14 dB (155mV)
CH Input 1,2 | cp, TAPE Pin Jack
15k ohms — 10 dB (245mV) + 20 dB (7.75V)
AUX
INST IN 15k ohms 600 ohm Lines — 20 dB (77.5mV) + 10 dB (2.45V) Phone jack
MIC IN 20k ohms 50— 250 ohm MICS — 50 dB (2.45mV) — 20 dB (77.5mV) Phone Jack
AUX RETURN 10k ohms 600 ohm Lines — 20 dB (77.5mV) + 10 dB (2.45V) Phone Jack
OUTPUT CHARACTERISTICS
Actual 249 Output Level
Connection impedance For Use With Nominal Connector In Mixer
Р Nominal Max. before clip
LINE OUT (L, R) 600 ohms 10k ohm Lines — 10 dB (245mV) +20 dB (7.75V) Pin Jack
MASTER OUT (L, R) 600 ohms 10k ohm Lines 0 dB (775mV) + 20 dB (7.75V) Phone Jack
PHONES OUT 100 ohms 8 ohm phones — 22 dB (0.5mW) —6 dB (19mW) STEREO Phone Jack
AUX SEND 600 ohms 10k ohm Lines — 10 dB (245mV) + 20 dB (7.75V) Phone Jack
12
DIMENSIONS
N 350 (13-7/10”) _ N 77(3") 0
A "a
Po YAMAHA го © mie 3 e 10153 913
MIXER ' + EE
> RAHOO vu vu ке
MIC L В
J
. > | . : CII) (С) 2
10 400 IKK a a ==, +
GRAPHIC EQUALIZER и РАМ R REGENERATION e
nl lo „Im nm] Fm. Nm SOURCE os
ma —Ño—— 9 —— b— 9 — À — 9 —]
|| в J TAPE С в — н- в — 28 — 2 .
=: e 58 7 Ci min + (CC
С — — “°
| - | — — — INST С
— — — 0 — — A — MAS CJ
MIC INST LINE OUT MASTER MONITOR
| CROSS FADER v Pues 4 /
| 26 (1”)
60 (2-2/5”) —
Unit : mm (inch)
YAMAHA Goose neck condensor mic MJM-10 is
avalrable for the MJ100.
A
Im
SERVICE
The MJ100 is supported by Yamaha's worldwide network
of factory trained and qualified dealer service personnel.
In the event of a problem, contact your nearest Yamaha
dealer.
13
YAMAHA
YAMAHA CORPORATION
PO.Box 1, Hamamatsu. Japan
8806 R1 CR Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement