Yamaha | RX-450 | Owner's Manual | Yamaha RX-450 Owner's manual

Yamaha RX-450 Owner's manual
EE MER Tt 0
“Connections - a
Operations Bisson
живя
a." rem.
Tuning Operations NT
Remote-Controi Transmitter EEE
Notes about the Remote Control Transmitter
Troubleshoocting o.oo e
Specifications... er EEE
“….
aus
Keep this O Owner Ss Manuali in a safe place.
for future reference... - |
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
To reduce the risk of fire or electric shock,
do not expose this appliance to rain or
moisture.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER {OR BACK), NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
- = sx of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert:
you to the presence of important -
operating. and maintenance (servicing)
instructions in the literature
accompanying the appliance.
Read Instructions — All the safety and operating
instructions should be read before the appliance is
operated.
Retain Instructions — The safety and operating
instructions should be retained for future reference.
. Heed Warnings — AI warnings on the appliance and
in the operating instructions should be ‘adhered to.
Follow Instructions — All operating and other
instructions should be followed.
Water and Moisture - The appliance should not be
used near water — for example, near a bathtub,
washbowl; kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.
— Carts and Stands — The appliance should be used =
- only with a cart or ‘stand that is recommended by the
- manufacturer.
6A An appliance and cart
10
11
12
13
14
15
combination should be moved
with care. Quick stops, excessive
force, and uneven surfaces may
cause the appliance and cart
combination to overturn.
Wall or Ceiling Mounting - The appliance should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
Ventilation - The appliance should be situated so that
its location or position does not interfere with its
proper ventilation. For example, the appliance should
not be situated on a bed, sofa, rug, or.similar surface,
that may block the ventilation openings; or placed in
a built-in installation, such as a bookcase or cabinet
that may impede the flow of air through the ventilation
openings.
Heat — The appliance should be situated away from
heat sources such as radiators, stoves, or other
appliances that produce heat.
Power Sources — The appliance should be connected
to a power supply only of the type described in the
operating instructions or as marked on the appliance.
Power-Cord Protection — Power-supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them,
paying particular attention to cords at plugs,
convenience receptacles, and the point where they
exit from the appliance.
Cleaning — The appliance should be cleaned only as
recommended by the manufacturer.
Nonuse Periods — The power cord of the appliance
should be unplugged from the outlet when left unused
for a long period of time.
Object and Liquid Entry — Care should be taken so
that objects do not fall into and liquids are not spilled
into the inside of the appliance.
Damage Requiring Service — The appliance should be |
serviced by qualified service personnel when:
17
18
The power- supply cord or the plug has been damaged; or
Objects have fallen, or liquid has been spilled into the
appliance; or
The appliance has been exposed to rain; or |
The appliance does not appear to operate normally or
“exhibits a marked change in performance; or
The appliance has been dropped, or the cabinet
damaged.
Servicing - The user “should not attempt to service the |
appliance beyond those means described in the
operating instructions. all other servicing should be
referred to qualified service personnel.
Power Lines — An outdoor antenna should be located
away from power lines.
Grounding or Polarization - — The precautions that
should be taken so that. the grounding or r polarization |
19
is not defeated.
Outdoor Antenna Grounding — + an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built up static charges. Section
810 of the National Electrical Code, ANSI/NFPA No.
70-1984, provides information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
ANTEN
DISCHA AGE
(NEC SECT ON 810-20)
ELECTRIC
SERVICE
EQUIPMENT
“GROUNDING CONDUCTORS
(NEC SECTION 810-21)
Lg GROUND CLAMPS
>=
gg ——— POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC — NATIONAL ELECTRAICAL CODE
Note to CATV system installer:
This reminder is provided to call the CATV system
installers attention to Article 820-22 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
1 To ensure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install your unit in a cool, dry, clean place — away
from windows, heat sources, and too much vibration,
dust, moisture or cold. Avoid sources of hum
(transformers, motors). To prevent fire or electrical
shock, do not expose to rain and water.
3 Do not operate the unit upside- down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If a foreign object drops into
the set, contact your dealer.
5 Do not use force on switches, knobs or cords. When
moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting
to other equipment. Never pull the cord itself.
6 Do not attempt to clean the unit with chemical
solvents; this might damage the finish. Use a clean,
dry cloth.
7 Always set the volume control to “-co ” before starting
the audio source play: increase the volume gradually
to an appropriate level after the play 5 started. —
8 To prevent lightning damage, pull out the power cord
and remove the antenna cable during an electrical
storm.
9 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that your
unit is faulty. |
10 Do not connect audio equipment to the AC outlets on
the rear panel if that equipment requires more power
than the outlets are rated to provide. |
The solder used in the manufacture of this product
contains LEAD. In addition, the electrical/electronic and/or
plastic (where applicable) components may also contain
traces of chemicals found by the California Health and
Welfare Agency (and possibly other entities) to cause
cancer and/or birth defects or other reproductive harm.
DO NOT REMOVE ANY ENCLOSURE COMPONENTS!
There are no user serviceable parts inside..All service
should be performed by a service representative
authorized by Yamaha to perform such service.
IMPORTANT MESSAGE: Yamaha strives to produce
products that are both user safe and environmentally —
“friendly”. We sincerely believe that our products meet
these goals. However, in keeping with both the spirit and
the letter of various statutes we have included the |
messages shown above and others in various locations in
this manual.
After unpacking, check that the following parts are contained.
Indoor FM Antenna AM Loop Antenna
Remote Control Transmitter Batteries (size “AAA”, ROS)
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to
any other components to which connections are being made.
When making connections between this unit and other components, be sure all connections are made correctly, that is to
say L (left) to L, R (right) to R, “+” to “+” and “—” to . Also, refer to the owner's manual for each component to be
connected to this unit.
Video cassette player, video disc player, etc. Speakers A
T=
== a
Turntable
REMOTE CONTROL
Tu oe oa EAU AA AAA AAA
| AUDIO OUT ef
(U.S.A. model)
Da ag cumeTa
OUTPUT
SWITCHED
"OO MAX TOTAL
EE oo |
Compact disc player LINE OUT
LINE IN
Left TO AC outlet
o
Led Е
Tape deck
> ||
2 RG
©)
Speakers B
Connecting speaker systems About the accessory terminals
® One or two speaker systems can be connected to this ®
unit. If you connect only one speaker system, connect it —
to either SPEAKERS A or B terminals.
® Use speakers with the specified impedance shown on
the rear of this unit.
® How to Connect:
Connect the SPEAKERS terminals to your speakers with
wire of the proper gauge, cut to be as short as
possible. Press and hold the SPEAKERS terminal tabs,
then insert the bare wires and secure them by releasing
the tabs. If these connections are faulty, no sound will
be heard from the speakers. Make sure that the polarity
of the speaker wires is correct, that is, + and ~ markings *
are observed. If these wires are reversed, the sound will
be unnatural and will lack bass. Do not let the bare
speaker wires touch each other as this could damage
this unit and/or speakers.
AC OUTLETS
(U.S.A., Canada, General and Europe models)
PS 2 SWITCHED OUTLETS
(Australia and U.K. models) cn 1 SWITCHED OUTLET
Use these to connect the power cords from your
components to this unit.
The power to the SWITCHED outlets is controlled by
this units POWER switch. They will supply power to
any component whenever this unit is turned on.
The maximum power (total power consumption of
components) thai can be connected to the SWITCHED
AC OUTLETS is 100 watts.
REMOTE CONTROL (PHONO) connector
If you have a YAMAHA turntable with the === mark,
connect it to this connector. This connection allows you
to control the turntable from the provided remote control
transmitter.
GND terminal
Connecting the ground wire of the turntable to this
terminal will produce minimum humming, but in some
cases better results may be obtained with the ground
wire disconnected.
e Each antenna should be connected to the designated terminals correctly, referring to the following figure.
e Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide
sufficient sensitivity. Furthermore, a properly installed outdoor antenna will give clearer reception than an indoor one. If
you experience poor reception quality, an outdoor antenna may result in improvement.
U.S.A, CANADA, UK., AUSTRALIA EUROPE MODEL
AND GENERAL MODELS
Indoor FM antenna | Indoor FM antenna |
Outdoor FM antenna (included) Outdoor AM antenna Qutdoor FM antenna (included) Outdoor AM antenna
TI
AM loop AM loop
antenna antenna
© (included) (included)
Te morn ween ae Mam TITER MAA RGA WIA NAO METE TAO METRO mewn rire dem
Z 1410 о
300-chm 75-ohm coaxial cable Ground |
feeder
| | | 300-ohm feeder —
75-ohm coaxial cable 75-ohm/300-ohm
antenna acapter
Connecting the AM loop antenna
* The antenna may be hung on a wall. 2 |
* The AM loop antenna should be kept being connected, even if an outdoor AM antenna is connected to this unit.
GND terminal | Notes
For maximum safety and minimum interference, connect e When connecting the
the GND terminal to a good earth ground if practical. A indoor FM antenna (for
good earth ground is a metal stake driven into moist Europe model), make
earth. sure that the grooved
part of the connector
hole is facing downward.
e If you need an outdoor
FM antenna to improve FM
reception quality, either 300-ohm feeder or coaxial cable
may be used. In locations troubled by electrical
interference, coaxial cable is preferable.
To listen to an aud
io source
VOLUME
Set to the “ co ” position.
OS | 4 POWER
—STANDBY
мираж TUNER
—L- E
Select the source you want to listen to.
INPUT
С =
ZTN
* If you want to listen to the tape deck;
TAPE
MONITOR
TAPE
MONITOR
ON/OFF
N= 4
ZN
PHONO
№
When not listening to the tape deck, set this switch so
that the indicator does not illuminate.
VOLUME
Adjust to the desired output level.
If desired, adjust the BALANCE, BASS, TREBLE,
LOUDNESS controls and the BASS EXTENSION
Switch. (Refer to the next page for details.)
_
To record a source to audio tape
Select the source to be recorded.
INPUT
O ! к \, —————————— МРОТ ———————
VIDEO/AUX TUNER dy, PHONO
НЕ BE me] —
TN
ió
Play the source and then turn the VOLUME control
up to confirm the input source.
Set the tape deck in the recording mode.
the SPEAKERS switches.
(Refer to the next page for details.)
Select the speaker system to be used by pressing
Play the source.
If your tape deck has three head monitoring
capability you can monitor the signal just recorded.
TAPE |
MONITOR
TAPE
MONITOR
Nav
— m] —
ah
ON/OFF
Note
Adjusting the VOLUME, LOUDNESS, BASS, TREBLE and
BALANCE controls during recording has no effect on the
material being recorded.
Adjust the balance of the output volume to the left and
night speakers to compensate for sound imbalance caused
from the speaker settings or the listening room condition.
BALANCE
0
BASS TREBLE
OEFEAT
DEFEAT
-5 5+ -5 5 +
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response. | |
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response. |
Because one or two speaker systems can be connected
to this unit, the SPEAKERS switches allow you to select
speaker system A or B, or both at once.
SPEAKERS
A В
ON ét ON
DEF OFF
This control provides compensation for the human ears’
loss of sensitivity to high and low-frequency ranges at low
volume. This control is adjustable to retain full tonal range
at any volume level.
1 LOUDNESS |
Dr «4048 Set to the “FLAT” position.
o 10
2 VOLUME
Set to the loudest listening level
that you would listen to.
LOUDNESS
FLAT Turn until the volume level
"404 is reduced to a desired level
without losing natural tone.
Using the BASS EXTENSION switch
You can boost bass frequency response by setting this
switch to the “ON” position.
BASS
EXTENSION
de ON
HA OFF
Using the CD DIRECT switch
You can enjoy purer CD sound by setting this switch to
the "ON” position. Because, by doing so, the CD input
signal is output directly, bypassing the LOUDNESS,
BALANCE controls, etc. therefore avoiding any “muddying”
caused by circuit routing.
CD DIRECT
& OFF ON
When you listen with headphones |
Connect the headphones to the PHONES jack. When
listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF postion.
PHONES
signals of the station you want to select are weak, you must tune to it manually.
Normally, if station signals are strong and there is no interference, quick automatic-search tuning is possible. However, if
watching the display.
Select the reception band (FM or AM) while
— AUTO TUNING STEREO
== | =
FM ZAM
~ ~ |
— AM — or — FAM —
A | “ A |
TUNING MODE
AUTO/MAN'L MONO — mE SU
Iii _——
LILA Maz О 40 60 80 100
SU
TUNING
DOWN
If the station where tuning search stopped
is not the desired one, press again.
TUNING
DOWN
up
E
if the tuning search does not stop at the
desired station;
TUNING MODE
AUTO/MAN'L MONC
“AUTO TUNING”
goes off.
TUNING
DOWN
UF
Гл * You can tune to the
Aa desired station
No manually.
, * To continue tuning search, press and hold the button.
Display information Note | ВЕ |
| If you tune to a FM station manually, it is received in
© monaural automatically to increase the signal quality.
| COÑA == —®
FMI PILI Maz 60 601000 >
STERED
|
©
@ Displays the band and frequency of the received
station.
@ Indicates the signal level of the received station.
© Wuminates when an FM stereo broadcast with sufficient
signal strength is received.
This unit can store station frequencies (selected by tuning operation) by using preset station buttons. With this function,
you can select any desired station by only pressing the corresponding preset station button. Up to 16 stations can be
programmed.
To program stations
Tune to a desired station.
(Refer to the previous page for tuning procedures.)
Select the range (P1-8 or P9-16) of the preset
station buttons while watching the display.
P1-8/P9-18
N |
— P4-PB —
LA
MEMORY p / ir
. ! FM Li ML
F1-F8 — MEMORY —
В |
Flashes on and off
for about 5 seconds.
P1/9 Pe P3B/11 Pale PS7/19 PE P7745 Pa/16
| | | | | | | |
! „=== ВЕ BE
Г
Ll MHz $ ad 60 60 160
Р I ra Li SA
Shows the displayed station
has been programmed to РТ.
* In the same way, program other stations to P?, P3 ...
P8.
* To program stations to P9, P10 ... P16, in step 2,
“P9-P16” should be illuminated in the display.
Notes
e In step 4, press a preset station button before
“MEMORY” goes off from the display.
e A new setting can be programmed in place of the
former one.
e For presets, the setting of the reception mode (stereo
or monaural) is stored along with the station frequency.
To recall a preset station
# Select the range of the preset station buttons.
P1-87P9-15
“|
or —_P9-P16 —
7
\
Ésa
P1/8 PP2710 Py PA/12 P5/13 PE/14 R215 PBS
| | | | | | | |
Select the desired one.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the power is cut (for timer use or
due to temporary power failure). If, however, the power is
cut (because of disconnection of the AC power plug etc.)
for more than two weeks, the memory may be erased. if
so, it can be re-programmed by simply following the
PRESET TUNING steps.
The remote-control transmitter provided with this unit is designed to control all the most commonly used functions of the
unit. If the CD player, turntable, equalizer, and tape deck connected to this unit are YAMAHA components designed for
remote control compatibility (components with an == mark), then this remote-control transmitter will also control various
functions of each component. Please consult YAMAHA dealer for information on which components are compatible with
the remote-control transmitter.
Key Functions
For Receiver Control
Turns the POWER on mode
to the STANDBY mode
and vice versa.
Selects preset station number. ji Selects input source.
* +: Selects higher preset station number.
—: Selects lower preset station number.
Turns the volume level up/down.
For Other Component Control
Identify the remote-control transmitter keys with your component's keys.
On each key function, refer to the corresponding instruction on your components manual.
Starts/stops record play on turntable.
Controls compact disc player.
* DISC SKIP is applicable only
to compact disc auto changer.
Controls equalizer. Controls tape deck.
* DIR A, B and DECK A/B are
applicable only to double
cassette tape deck.
10
STANDBY Mode
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit to the STANDBY
| /
mode. (In this mode, the indicator is half illuminated.) JRE = emmy
POWER on mode | STANDBY mode
NOTES ABOUT THE REMOTE
Battery installation
Battery replacement
if the remote-control transmitter must be used closer to
the main unit, the balteries are weak. Replace both
batteries with new ones.
Notes:
Use only “AAA” (RO3) batteries for replacement. |
Be sure the polarities are correct. (See the illustration
inside the battery compartment.)
Remove the batteries if the remote-control transmitter
will not be used for an extended period of time.
If batteries leak, immediately dispose of them. Avoid
touching the leaked material or letting it come in
contact with clothing, etc. Clean the battery
~ compartment thoroughly before installing new batteries.
Remote-control transmitter operation range
/
\
A
Remote-controi
sensor
\_ Within approximately
\ 7 m (23 feet)
There should be no large obstacles between the remote-
control transmitter and the main unit.
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. if it
cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your dealer or service center for help.
SYMPTOM
CAUSE
REMEDY
The receiver fails to turn on when the POWER
switch is pressed.
Power cord is not plugged in or is not completely
inserted.
Firmly plug in the power cord.
There is distortion and clear reception cannot
be obtained even with a good FM antenna.
There is multipath interference.
= | No sound. Incorrect output cord connections. Connect cord properly. If the problem persists, the
= | cables may be defective.
o
Е Incorrect input selection. Set the receiver controls to the correct input
< selection.
Sound “hums”. Incorrect cord connections. Firmly connect the audio plugs. If the problem
persists, the cord may be defective.
FM stereo reception is noisy. Because of the characteristics of FM stereo Check the antenna connections.
broadcasts, this is limited to cases where the Try using a multiple element FM antenna.
transmitter is far away or the antenna input is
= poor.
LL
Adis antenna placement to eliminate multipath
interference.
A desired station cannot be tuned in with
Auto tuning.
The station is too weak.
Use Manual tuning mode.
Use high quality directional FM antenna,
AM
A desired station cannot be tuned in with
Auto tuning.
Weak signal or loose antenna connections.
Tighten the AM loop antenna connections and
rotate it for best reception.
Use Manual tuning mode.
There are continuous crackling and hissing
noises.
These noises result from lightning, fluorescent
lamps, motors, thermostats and other electrical
equipment.
Use an outdoor antenna and a ground wire. This
will help some what but if is difficult to eliminate
all noise.
There are buzzing and whining noises
A television set is being used nearby.
Move the television away.
(especially in the evening).
11
SPECIFICATIONS
AUDIO SECTION
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.04% THD
[U.S.A.,Canada and General models] .... 45 W
[Australia, Europe and U.K. models] .40 W
6 ohms, 20 Hz to 20 kHz, 0.06% THD
[U.S.A.,Canada and General models] .... 48 W
4 ohms, 20 Hz to 20 kHz, 0.1% THD |
[Canada model only] ..................... 50 W
Dynamic Power per Channel (IHF)
8/6/4/2 ohms
[U.S.A Canada and General models]
PS 78/90/108/112 W
[Australia, Europe and U.K. models]
ra era ae annee nee R nana a casse unes 75/84/100/103 W
DIN Standard Output Power per Channel
4 ohms, 1 kHz, 0.7% THD
[Europe model only] ...................... 55 W
IEC Power (1 kHz, 0.04% THD, 8 ohms) .
[Europe model only] ...................... 50 W
Power Band Width
8 ohms, 20 W, 0.1% THD ..... 10 Hz to 40 kHz
Damping Factor
8 ohms, 1 KHZ ....................... 50 or more
input Sensitivity/lmpedance
PHONO ....................... 2.5 mV/47 k-ohms
CD/TAPENIDEO/AUX ......... 150° mV/50 k-ohms
Maximum Input Signal Level (1 kHz, 0.01% THD)
PHONO .... i. 110 mV
Output Level/impedance |
REC OUT ..................... 150 mY/550 ohms
Headphone Jack Rated Output/impedance
fee eer errr eae 0.6 V/ 8 ohms
Frequency Response (20 Hz to 20 kHz)
CD/TAPE/VIDEO/AUX .................... <0.5 dB
RIAA Equalization Deviation (20 Hz to 20 kHz)
PHONO ii, E +0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
"PHONO to REC OUT (3 V) .............. 0.01%
CD/TAPE/VIDEO/AUX to SP OUT (20 W/8 ohms)
PS 0.02%
Intermodulation Distortion
CD/TAPE/VIDEO/AUX (Rated Output/8 ohms)
a eerococoroooecec ran reoccorarorbcamo neo ... 0.04%
Signal-to-Noise Ratio (HF-A Network)
PHONO (5 mV Input Shorted) |
[U.S.A..Canada, U.K., Australia and
- General models] ......................... . 87 dB
[Europe model only]
ee hee ere eae eee 82 dB
CD/TAPE/VIDEO/AUX (Shorted) ........... 103 dB
Residual Noise (IHF-A Network) ............ 140 pV
Channel Separation (1 kHz, Vol. -30 dB)
PHONO (Input Shorted) ................. ... 55 dB
CD/TAPE/VIDEO/AUX | |
(Input 5.14 k-ohms Terminated) ............ 52 dB
Tone Control Characteristics
BASS : Boost/cut .............. +10 dB (50 Hz)
Turnover Frequency .............. . 350 Hz
TREBLE : Boost/cut ........... +10 dB (20 kHz)
Turnover Frequency .......... 3.5 kHz
Filter Characteristics |
Bass Extension ...................... 60 Hz, 8 dB
naoavaaa Mersin, 0 OB (1 kHz)
(Level related equalization)
FM SECTION
Tuning Range
[U.S.A.,Canada and General models]
eer. 000044404. 87.5 to 107.9 MHz
[Australia, Europe, U.K. and General models]
freee ieee, 87.5 to 108.0 MHz
50 dB Quieting Sensitivity (IHF, 75 ohms)
— [Except Europe model]
Mono ne 1.55 uV (15.1 dBf)
Stereo .............._._eenvovareeoo 21 wv (37.7 dB
Usable Sensitivity (75 ohms)
(30 dB S/N Quieting, 1 kHz, 100% mod.)
[Except Europe model] ...... 0.8 nV (9,3 dB
DIN, Mono (S/N 26 dB) [Europe model]
PP FETT 09 4 V
DIN, Stereo (S/N 46 dB) [Europe model] —
PE PERRET o avarnaroaaacenazancoeo e 24 uV
Image Response Ratio
[Except Europe model] .............. ... 45 dB
[Europe model] .......................... 80 dB
IF Response Ratio ......................... ... 80 dB
Spurious Response Ratio .................... 70 dB
AM Suppression Ratio ....................... 55 dB
Capture Ratio ee 1.5 dB
Alternate Channel Selectivity |
[Except Europe model] .................. 85 dB
Selectivity (two signals, 40 kHz Dev.)
(Europe model] e... 50 dB
Signal-to-Noise Ratio |
(IHF) Mono/Stereó
[Except Europe model] ............... 81/76 dB
(DIN-weighted, 40 kHz Dev.) Mono/Stereo =
[Europe model] ......................... 75/70 dB
Harmonic Distortion (1 kHz) :
Mono/Stereo | - o
[Except Europe model] ..... re. 0.1/0.2% -
Stereo (40 kHz Dev.) a
[Europe model] ........... rear, .. 0.2%
Frequency .Response ; о.
30 Hz to 13 kHz ..................... 0+0.5 dB
20 Hz to 15 kHz ..:...£.... 0... 0+1.5 dB
Stereo Separation (1 kH7)- =. . a
[Except Europe model] .................. ‘50 dB
[Europe model (40 kHz Dev.)] .......... 50 dB
AM SECTION
Tuning Range |
[U.S.A Canada and General models]
e ennadiveoacoranenaa ao aser 530 to 1,710 kHz
[Australia, Europe, U.K. and General models]
eee reas 531 to 1,611 kHz.
Usable Sensitivity ................ ean 100 uV/m
Selectivity ..........., eee eee 32 dB
Signal-to-Noise Ratio .............. ieee, 50 dB
image Response Ratio ....... ere, 40 dB
Spurious Response Ratio ......... rea 50 dB
Harmonic Distortion (400 Mz) ................. 0.3%
AUDIO SECTION
Output Level/impedance |
FM (100% mod., 1 kHz)
[Except Europe model]
reece. 500 mvj2.2 k-ohms
[Europe model (40 kHz Dev.)]
ESS 400 mV/6. 8 k-ohms
AM (30% mod., 400 Hz)
[Except Europe model]
Ce eres 150. mV/2.2 k-ohms
[Europe model (40 kHz Dev.)] -
Creer ea - 150 mV/6.8 k-ohms
GENERAL -
Power Supply
[U.S.A. and Canada models]
SES нана нкаажкеавбнееасоб0... AC 120 V, 60 Hz
[Australia and U.K models] :
Meacarcoremaao icon onetccaorooa AC 240 Y, 50 Hz
[Europe model] .......... .... AC 230 V, 50 Hz
[General model]
Lecce canne es AC 110/120/220/240 V, 60/50 Hz
Power Consumption
[U.S.A. model only] ........ een. ve... 180 W
[Canada model only] ....... eee, ...200 W
[Australia, Europe, U.K. and General models]
J PPR 160 W
AC Outlets
[U.S.A. Canada and General models only]
Switched ........................ SAN 100 W max.
Dimensions (W x H x D) |
career nes arc na es rc. 435 X 131 x 292 mm
(17-1/8" x 5-3/16” x 11-1/2")
Weight 0. 5.7 kg (12 Ibs. 9 oz.)
— Accessories .................... ... AM loop antenna
Indoor FM antenna
Remote Control Transmitter
Batteries
Specifications subject to change without notice.
YAMAHA ELECTRONICS CORPORATION, USA 6722 ORANGETHORPE AVE, BUENA PARK, CALIF. 90620, US.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE. SCARBOROLIGH, ONTARIO M1S 381, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, D-2084 RELUINGEN, BEI HAMBURG, FR. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. 17 RUE DES CAMPANULES, LOGNES 77321 MARNE LA VALLEE CEDEX 2, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÓLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
YAMAHA CORPORATION
VJ91940-0 BWWB£. BB£ ® @ Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising