VADDIO | ZOOMSHOT WALLVIEW SR 999-6918-001 | User guide | VADDIO ZOOMSHOT WALLVIEW SR 999-6918-001 User guide

VADDIO ZOOMSHOT WALLVIEW SR 999-6918-001 User guide
Installation and User Guide
VADDIO™ ZOOMSHOT™ WALLVIEW™ SR
High Definition Point of View Camera System with 19X Optical Zoom
Model Number 999-6918-000 (North America)
Model Number 999-6918-001 (International)
© 2014 Vaddio - All Rights Reserved. ZoomSHOT WallVIEW SR - Document Number 342-0651 Rev B
Zoom SHOT WallVIEW SR
TABLE OF CONTENTS
Overview .................................................................................................................................................................... 3 Unpacking: ................................................................................................................................................................. 4 Front View with Feature Call-outs .......................................................................................................................... 4 Image: ZoomSHOT HD PTZ Camera ............................................................................................................... 4 Rear Panel Connections with Feature Call-outs .................................................................................................... 5 Image: ZoomSHOT HD Camera ....................................................................................................................... 5 Quick-Connect SR Interface ...................................................................................................................................... 6 Image: Rear Panel with Feature Call-outs ........................................................................................................ 6 First Time Set-up: ...................................................................................................................................................... 6 Step By Step Installation Instructions: ................................................................................................................... 7 Image: Basic Wiring Configuration .................................................................................................................... 8 Compliance and CE Declaration of Conformity - ZoomSHOT .................................................................................. 9 Warranty Information ............................................................................................................................................... 10 ZoomSHOT WallVIEW SR General Specifications: ............................................................................................ 11 Appendix 1: Pin-outs for ZoomSHOT Camera ....................................................................................................... 12 Table EZCamera Power & HD Video RJ-45 Connector Pin-outs .................................................................... 12 Appendix 2: Pin-outs for Quick-Connect SR Interface ........................................................................................... 12 Table: DE-15 - YPbPr Pin-Out ........................................................................................................................ 12 Communication Specification .................................................................................................................................. 13 ZoomSHOT Command List (1/2)...................................................................................................................... 13 ZoomSHOT Command List (2/2)...................................................................................................................... 14 ZoomSHOT Inquiry List (1/1) ........................................................................................................................... 15 ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 2 of 16
Zoom SHOT WallVIEW SR
OVERVIEW:
The Vaddio ZoomSHOT HD camera produces amazing results for
small, medium and large room applications. Anywhere that a Pointof-View or stationary camera can be used alone or in conjunction
with a Vaddio PTZ camera to simplify camera coverage and preset
positioning, the ZoomSHOT is the answer.
Essentially, the ZoomSHOT is a low cost pan/tilt/zoom camera,
where the pan and tilt are adjusted manually. However, unlike
security-type stationary cameras, the ZoomSHOT is equipped with a
19X optical power zoom lens that produces a horizontal field of view
ranging from 58º on the wide end to 3.1º on the tele end in a HD 16:9
format.
ZoomSHOT HD is a camera with a unique pedigree. Designed from
the ground up, this HD camera uses the Vaddio EZCamera™ Cat-5
wiring standard for video, power and control. Using HSDS™ (high
speed differential) video outputs over Cat-5 cable, the ZoomSHOT
sports a wide range of video resolutions that are selectable from the
rear panel; from 480p/59.94-YPbPr up to and including 1080p/60.
The HSDS processing allows delivery of the HD video signals up to
150’ (45.72m).
Image: ZoomSHOT HD Camera
Choose between three (3) IR frequencies for the Vaddio IR Shot
Commander to allow multiple cameras to be locally IR controlled with
a single remote control. The ZoomSHOT also has an OSD (on
screen display) for easy set-up and basic image control that’s
accessible with the IR remote. Up to six (6) camera zoom presets
can be programmed and recalled via the remote or RS-232 (up to 16
zoom presets with RS-232). IR signal forwarding is also included.
ZoomSHOT is paired with the tried-and-true Quick-Connect SR
Interface in this package which represents a super-high value and a
very low price. So breathe easy, and try a ZoomSHOT today!
Image: ZoomSHOT Rear Panel
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and
tested for use indoors with the power supply provided. The use of a power supply, other than the one provided, or
outdoor operation has not been tested and could damage the device and/or create a potentially unsafe operating
condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of
electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.
Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent connections which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS (high
speed differential) signals. For best results please use standard RJ-45 connectors and test all
cables for proper pin-outs prior to use and connection to Vaddio product.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from
www.vaddio.com free of charge.
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 3 of 16
Zoom SHOT WallVIEW SR
UNPACKING:
Carefully remove the product and all of the included parts from the packaging.
Identify the following parts for each camera:
ZoomSHOT WallVIEW SR Camera System (North America):
Part Number: 999-6918-000
 One (1) ZoomSHOT HD Camera (998-6918-000)
 One (1) Vaddio IR SHOT Commander Remote
 One (1) Quick-Connect SR Interface
 One (1) 3-Position Phoenix-type Connector for IR Forwarding
 One (1) 24 VDC, 2.0 A Power Supply with Power Cord for North America
 One (1) Thin Profile Wall Mount with Mounting Hardware
 One (1) EZCamera™ Control Adapter (RJ-45-F to DB-9-F)

Documentation
ZoomSHOT WallVIEW SR Camera System (International):
Part Number: 999-6918-001
 One (1) ZoomSHOT HD Camera (998-6918-000)
 One (1) Vaddio IR SHOT Commander Remote
 One (1) Quick-Connect SR Interface
 One (1) 3-Position Phoenix-type Connector for IR Forwarding
 One (1) 24 VDC, 2.0 A Power Supply
 One (1) Euro Power Cable
 One (1) UK Power Cable
 One (1) Thin Profile Wall Mount with Mounting Hardware
 One (1) EZCamera™ Control Adapter (RJ-45-F to DB-9-F)
 Documentation
Front View with Feature Call-outs
Image: ZoomSHOT HD PTZ Camera
①
③
②
④
⑤
1) Lens: 19X Optical Zoom Lens
2) IR Sensor and Power LED: The IR sensor for the IR Shot Commander Remote is located here. In a
separate opening, a blue LED power light and a red LED tally resides (turns purple on boot up).
3) The Yoke: For manual pan and tilt. Tilt range is ± 30° and Pan is limited to the service loop of the cabling.
4) The Aluminum Base and Steel Cylindrical Body: Please don’t drop it on your foot, it’s fairly substantial.
5) Logo: Really Cool Logo Badge (RCLB). The RCLB is affixed to the base in a recessed ovoid area.
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 4 of 16
Zoom SHOT WallVIEW SR
Rear Panel Connections with Feature Call-outs
Image: ZoomSHOT HD Camera
②
①
④
③
1) RS-232 & IR Out: The RS-232 accepts modified VISCA protocol for camera control, as well as transmits IR
signaling received by the front IR receiver, which can be transmitted to third party devices.
2) EZ Power/Video Port:
This RJ-45 connector is only used with the Quick-Connect SR, Quick-Connect DVI-D/HDMI SR Interface, QuickConnect USB and USB Mini Interfaces to supply power and return HSDS (differential) video from the camera
over Cat-5 cable up to distance of 150’ (45.72m).
3) Dip Switch Settings:
Settings for IR remote frequency, IR receiver on/off, image flip, test bars and defaults can be configured on these
switches. See the Switch Settings page for additional information. The dip switch settings are as follows:
Dip Switch
1
2
3
4
5
6
All Down
Function
Up = IR1, Down = IR2
Up = IR 1 or 2, Down = IR3
Up=IR ON, Down = IR OFF
Up = Normal Image, Down = Image Flip
Test Bars
Update Position - Leave UP unless updating firmware
Reset to Defaults - with power cycle
4) HD Video Select:
A rotary switch allows the user to choose the component HD output video resolution and format. See the HD
Video Select Rotary Switch Settings are as follows:
Rotary
0
1
2
3
4
5
6
7
Resolutions
720p/59.94
1080i/59.94
1080p/59.94
-720p/50
1080i/50
1080p/50
480p/59.94
Rotary
8
9
A
B
C
D
E
F
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Resolutions
576p/59.94
-----1080p/29.97
1080p/25
Page 5 of 16
Zoom SHOT WallVIEW SR
QUICK-CONNECT SR INTERFACE
Image: Rear Panel with Feature Call-outs
①
②
③
④
⑤
1) Power Input:
5.5mm OD x 2.5mm ID coaxial connector for the provided PowerRite 24 VDC, 2.0 Amp power supply.
2) EZCamera Power & HD Video:
A single Cat-5 connection between the EZCAMERA POWER & HD VIDEO RJ-45 connector and the camera’s
EZ Power HD Video Port on the HD-19 camera extends power and video. Power is fed to the camera and HSDS
video is returned from the camera on the same Cat-5.
3) HD Video Output:
DE-15 connector outputs the YPbPr analog component HD video, which was extended from the camera over
Cat-5 cable. SD video resolutions (Y/C and CVBS formats) are not supported by the Quick-Connect SR
Interface, however analog component SD video is supported.
4) IR Output:
With the IR pass-thru turned ON (see camera dip switch settings), IR from third-party IR remote controls can be
sent through the ZoomSHOT camera to third-party equipment, such as hardware videoconferencing codecs. IR
can be used as either modulated (through the air) or non-modulated (wired) signals).
5) RS-232 Input & Output Jacks:
These RJ-45 connectors allow an external controller (beware of upcoming shameless plug) like the
ProductionVIEW™ Precision Camera Controller to route through the Quick-Connect SR for ease of cabling.
FIRST TIME SET-UP:
The ZoomSHOT was designed to be very easy to use and operate. There is documentation at the back of this
manual for pin-outs of the connectors on the Quick-Connect and camera.
Before Installing:
 Choose camera mounting location, paying close attention to camera viewing angles, lighting conditions,
possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted.
Always pick a mounting location that will optimize the performance of the camera.
 The Thin Profile Wall Mount for the ZoomSHOT can be mounted directly to a 1-gang wall box or can be
mounted using only dry wall anchors.
 For Power/Video and RS-232 signals, use standard Cat-5 cable (568B termination and real RJ-45
connectors) from the EZ-POWER VIDEO and RS-232 ports on the back of the ZoomSHOT to the QuickConnect SR Interface. The EZ-POWER VIDEO jack on the camera is highlighted red as a reminder that
there is 24 VDC power on that Cat-5 cable.
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 6 of 16
Zoom SHOT WallVIEW SR
Step By Step Installation Instructions:
Step 1: After determining the optimum location of the camera, route, mark and test the two (2) Cat-5 cables from
the camera to the Quick-Connect SR Interface located at the head-end. The two Cat-5e cables should feedthrough the hole located on the rear flange of the Thin Profile Wall Mount. If the bracket is to be mounted on a 1gang wall box, use the screws supplied with the wall box cover plate to attach the Thin Profile Wall Mount. If
mounting to the drywall with wall anchors, use two (2) quality wall anchors. The mounting holes are slotted and
are 90° opposing to provide easy leveling. Level the mount and tighten the mounting screws.
Step 2:
Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS dip switches on the back of the camera,
set up the camera’s output resolution and functional preferences. There are tables on previous pages that
identify the choices…maybe keep these tables handy for future use…or you can easily look them up on the
Vaddio website (vaddio.com) when needed.
On the camera:
 Set the desired HD Resolution with the rotary selection switch.
 Set the IR frequency of the camera (if it is to respond to the IR remote control).
 Set the image orientation (normal or flipped).
Step: 3: Follow the sample wiring diagram for connecting the Cat-5 cables to the ZoomSHOT and QuickConnect SR Interface (yep, on the next page, but read and understand the rest of these instructions especially
the next note).
NOTE: Check all Cat-5e cables for continuity in advance of the final connection. Label the
Cat-5e cables. Plugging the EZ-POWER VIDEO cable into the wrong RJ-45 may cause
damage to the camera system and void the warranty. For premise cabling, please use real
RJ-45 connectors and crimpers. Please don’t use the pull through or EZ type of RJ-45.
Step 4: Place the camera onto the camera mount and use the provided ¼”-20 screws to secure the camera to
the mount. To dress the cabling, push the extra cable back into the wall opening.
Step 5: Connect the Vaddio 24 VDC, 2.0 Amp power supply to a power outlet and to the Quick Connect SR
Interface. Power will travel down the EZ-POWER VIDEO Cat. 5 cable to the camera. The camera will boot up
and in a few seconds, HSDS (differential) video will travel back down the Cat-5 cable and be ready to accept
control information from the IR remote control or RS-232 camera controller.
To insure proper continuity of control and operation of the cameras, the RS-232 controller (control
system or joystick) should be powered on after the camera.
.
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 7 of 16
Zoom SHOT WallVIEW SR
Image: Basic Wiring Configuration
ZoomSHOT
Rear View
RS-232 & IR
OUT Cat-5
For Zoom &
CCU Control
HSDS (differential) HD Video &
24 VDC Power One (1) Cat-5 Cable
← YPbPr (HSDS differential)
Power
→
Rear Panel
Quick-Connect SR Interface
YPbPr
24VDC, 2.0 A
PowerRite Power
Supply
HD Monitor
(Simulated HD Video Feed)
ProductionVIEW Precision Camera Controller
Note: RS-232 Control can be run through the RS-232
IN and OUT of the Quick-Connect SR Interface and is
required for use with IR Forwarding.
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 8 of 16
Zoom SHOT WallVIEW SR
COMPLIANCE AND CE DECLARATION OF CONFORMITY - ZOOMSHOT
Compliance testing was performed to the following regulations:

FCC Part 15 (15.107, 15.109), Subpart B

ICES-003, Issue 4: 2004

EN 55022 A: 2006 + A1: 2007

KN22 2008 (CISPR 22: 2006)

KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002)

EMC Directive 2004/108/EC

EN 55024: A2: 2003
Class A
Class A
Class A
Class A
Class A
Class A
Class A
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his/her own
expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC
EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005)
EN 55024: A2: 2003







EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001
EN 61000-4-3: 2006 + A1: 2008
EN 61000-4-4: 2004 + Corrigendum 2006
EN 61000-4-5: 2006
EN 61000-4-6: 2009
EN 61000-4-8: 2010
EN 61000-4-11: 2004
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002)







EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
IEC 60950-1:2005 (2nd Edition); Am 1:2009
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Class A
Immunity
Electrostatic Discharge
Radiated Immunity
Electrical Fast Transients
Surge Immunity
Conducted Immunity
Power Frequency Magnetic Field
Voltage Dips, Interrupts and Fluctuations
IT Immunity Characteristics
Electrostatic Discharge
Radiated Immunity
Electrical Fast Transients
Surge Immunity
Conducted Immunity
Power Frequency Magnetic Field
Voltage Dips, Interrupts and Fluctuations
Safety
Safety
Page 9 of 16
Zoom SHOT WallVIEW SR
WARRANTY INFORMATION
(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):
Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio
warrants its manufactured products against defects in materials and workmanship for a period of two years from the day of
purchase, to the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will
repair or replace products that prove to be defective. Vaddio manufactures its hardware products from parts and components
that are new or equivalent to new in accordance with industry standard practices.
Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the
customer, customers applied software or interfacing, unauthorized modifications or misuse, mishandling, operation outside the
normal environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site
operation and maintenance. OEM products and products manufactured by other companies are excluded and are covered by
the manufacturer’s warranty.
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor
charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for
testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs
and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at
support@vaddio.com or online at vaddio.com.
Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from
Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product
serial numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of
purchase. See the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be
issued to Vaddio dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in
all correspondence with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the
product. All products returned for credit are subject to a restocking charge without exception.
Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, use of incorrect power supply, use of a modified power
supply or unauthorized repair.
Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound
freight carrier. If the return shipment appears damaged, retain the original boxes and packing material for inspection by the
carrier. Contact your carrier immediately.
Products not under Warranty: Payment arrangements are required before outbound shipment for all out of warranty
products.
*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.
Other General Information:
Care and Cleaning
Do not attempt to take this product apart at any time. There are no user-serviceable components inside.





Do not spill liquids in the product
Keep this device away from food and liquid
For smears or smudges on the product, wipe with a clean, soft cloth
Use a lens cleaner on the lens - not a hanky
Do not use any abrasive chemicals.
Operating and Storage Conditions:
Do not store or operate the device under the following conditions:







Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)
High humidity, condensing or wet environments
In inclement weather
In swimming pools or under waterfalls
Dry environments with an excess of static discharge
In orbit (vacuum issue)
Under severe vibration
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 10 of 16
Zoom SHOT WallVIEW SR
ZoomSHOT WallVIEW SR General Specifications:
ZoomSHOT Camera System
Part Numbers
Image Sensor
Video Output Resolutions
Lens/ Focal Length
Horizontal Viewing Angle
Video S/N Ratio
Minimum Illumination
Serial Control Protocol
Manual Pan/Tilt Range
Preset Positions
Tally Light
Camera Connectors
HD Video Select
Camera Settings
Thin Profile Wall Mount
User Controls
Materials & Weight
Dimensions:
ZoomSHOT WallVIEW 999-6918-000 (North America)
ZoomSHOT WallVIEW 999-6918-001 (International)
1/3-Type Exmor High-speed, Progressive Scan CMOS Sensor with 1.3 Megapixels
HD: 1080/59.94/50/30/25, 1080i/59.94/50, 720p/59.94/50
SD: 480p/59.94 & 576p/50
19X Optical Zoom, F=4.5mm wide to 85mm tele end (F1.6-F2.9), Min. Focus Distance 1.0m
58.1° Wide End to 3.2° Tele End - 16:9 Format
>52 dB
0.7 LUX (F1.6, 50IRE)
RS-232 (Modified VISCA)
Pan: Limited to service loop of cabling, yoke and base are mechanical only
Tilt: ± 30°
Invertible for Ceiling Mount
Six (6) Programmed and Recalled via IR Remote, 16 Programmed and Recalled with RS-232
Available through RS-232 Control
Two (2) RJ-45 Jacks:
 EZ-Power VIDEO RJ-45 Jack for use with Quick-Connect - Supplies power to the camera and
returns differential HD video from the camera
 RS-232 RJ-45 Jack (RS-232 Communication and IR Out (with Quick-Connect -SR Interfaces
16-Position Rotary Switch: Used to set HD Video Resolution Output
6-Position Dip Switch: For IR Freq., Baud Rate 9600, Image Flip & Test Bars
16-Position Rotary Switch for Output Resolution Settings
535-2000-237 (Provided with WallVIEW Systems)
Black powder coating, Sized to fit on 1-gang wall box or drywall mounting
IR Shot Commander Remote with OSD for set-up, RS-232 Port for External Control
Aluminum & Steel, Weight = 2.75643 lbs. (1.68kg)
Tube: 3” ( 76.2mm) Diameter x 4.75” (120.65mm) Long
Base: 5.5” (139.7mm) Diameter
Overall Height: 5.5” (139.7mm) Tall
Quick-Connect SR Interface
Connectors
Power Supply
Dimensions (H x W x D)
Weight
Accessory
Power Connector: 5.5mm OD, 2.5mm ID coaxial connector
Power/Video RJ-45: Supplies power to, and differential HD video from the camera
Video Output: DE-15 connector for HD Analog Component (YPbPr) video only (No SD Support)
IR Output: Transmits modulated or non-modulated IR signals received from the camera’s IR
receiver
 RS-232 IN RJ-45: Accepts RS-232 from ProductionVIEW or other external control systems
 RS-232 OUT RJ-45: Sends RS-232 from Quick-Connect SR to the camera
24 VDC, 2.0 Amp
1/3 Rack Size - 1.6” (40.64mm ) H x 5.5” (139.7mm) W x 3.25” (82.5500000000001mm) D
0.45 lbs. ( 0.2041165643 kg)
Rack Mount Adapter: 998-6000-002 - Holds three (3) Quick-Connect SR Interfaces




Moon in Front Page Header: Europa - Sixth closest moon of the planet Jupiter.
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 11 of 16
Zoom SHOT WallVIEW SR
APPENDIX 1: PIN-OUTS FOR ZOOMSHOT CAMERA
Table EZCamera Power & HD Video RJ-45 Connector Pin-outs
ZoomSHOT EZPOWER HD VIDEO PORT
Pin
YPbPr
1
Power+
2
Power3
Y+
4
PB+
5
PB 6
Y7
PR+
8
PR-
EZ POWER
HD VIDEO
12345678
Important Note: The EZ POWER HD VIDEO RJ-45 Connector is for use with the Quick-Connect SR,
Quick-Connect DVI/HDMI SR, Quick-Connect USB and USB Mini Interfaces ONLY (568B Wiring
Standard). The video signals are differential (HSDS™) and can only be received by the interfaces
above.
ZoomSHOT Camera RS-232 Port
Pin #
Function
Pin - 1
N/A
Pin - 2
N/A
Pin - 3
N/A
Pin - 4
IR Output (Diff Signal to Quick-Connect)
Pin - 5
IR Ground (Diff Signal to Quick-Connect)
Pin - 6
Digital GND
Pin - 7
RXD (from TXD of control source)
Pin - 8
TXD (to RXD of control source)
RS-232
12345678
APPENDIX 2: PIN-OUTS FOR QUICK-CONNECT SR INTERFACE
Table: DE-15 - YPbPr Pin-Out
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
YPbPr
Pr
Y
Pb
Pr GND
Y GND
Pb GND
GND
-
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 12 of 16
Zoom SHOT WallVIEW SR
COMMUNICATION SPECIFICATION
Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control
12345678
Pin #
1)
2)
3)
4)
5)
6)
7)
8)
RJ-45 RS-232 and IR Out Pins
Unused
Unused
Unused
IR Output (Diff Signal to Quick-Connect SR)
IR Ground (Diff Signal to Quick-Connect SR)
GND (GND of IR Short Range - Pin 3)
RXD (from TXD of control source)
TXD (to RXD of control source)
NOTE: The Vaddio ZoomSHOT control protocol is similar, but not identical to the Sony® VISCA™ command set
in order to be compatible with several popular control devices. Not all VISCA commands are supported and
there are many ZoomSHOT specific commands in the following Command and Inquiry Lists.
ZoomSHOT Command List (1/2)
Command Set
Address Set
IF_Clear
Command Cancel
CAM_Power
CAM_Zoom
CAM_Focus
CAM_WB
CAM_RGain
CAM_BGain
CAM_AE
CAM_Iris
CAM_Gain
CAM_Bright
CAM_Backlight
CAM_Aperture
Command
Broadcast
Broadcast
On
Off(Standby)
Stop
Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Direct(Variable)
Stop
Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct
Auto
Manual
One Push WB
Reset
Up
Down
Direct
Reset
Up
Down
Direct
Full Auto
Manual
Reset
Up
Down
Direct
Reset
Up
Down
Direct
Reset
Up
Down
Direct
On
Off
Reset
Up
Down
Direct
Command Packet
88 30 01 FF
88 01 00 01 FF
8x 2p FF
8x 01 04 00 02 FF
8x 01 04 00 03 FF
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 00 0p 0q 0r FF
8x 01 7E 01 4A 0v 0p 0q 0r 0s FF
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF
8x 01 04 35 00 FF
8x 01 04 35 03 FF
8x 01 04 35 05 FF
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 0p 0q 0r 0s FF
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 0p 0q 0r 0s FF
8x 01 04 39 00 FF
8x 01 04 39 03 FF
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF
8x 01 04 0D 00 FF
8x 01 04 0D 02 FF
8x 01 04 0D 03 FF
8x 01 04 4D 00 00 0p 0q FF
8x 01 04 33 02 FF
8x 01 04 33 03 FF
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Comments
Address Set (Daisy chain)
IF Clear
p:socket number(1,2)
Power On/Off
p:(0-Slow to 7-Fast)
pqrs: Zoom Position*
v: zoom speed
pqrs: Focus position*
Normal Auto (Auto Tracing WB)
Manual White Balance
One Push White Balance Mode
pqrs:00-ffff
pqrs:00-ffff
Auto Exposure Mode
Manual Control Mode
pq(0x00-0x11)
pq(0x00-0x11)
pq(0x00-0x24)
pq(0x00-0x1F)
Page 13 of 16
Zoom SHOT WallVIEW SR
ZoomSHOT Command List (2/2)
Command Set
CAM_Memory
CAM_IDWrite
IR_Receive
CAM_LR_Reverse
CAM_PictureEffect
Tally
Preset Pan Speed
BLK.Enhance
GMA.Enhance
CRM.Enhance
KNE.Enhance
DIS.Enhance
SNR.Enhance
AGC.Enhance
CAM_Shutter
CAM_ICR
Command
Reset
Set
Recall
On
Off
On
Off
Color
B&W
On
Off
Zoom Speed
No support
Gamma
Chroma
Knee
Digital Image
Stabilizer
Digital Noise
Reduction
AGC Mode
Reset
Up
Down
Direct
ICR On
ICR Off
Command Packet
8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x 01 04 3F 02 0p FF
8x 01 04 22 0p 0q 0r 0s FF
8x 01 06 08 02 FF
8x 01 06 08 03 FF
8x 01 04 61 02 FF
8x 01 04 61 03 FF
8x 01 04 63 00 FF
8x 01 04 63 04 FF
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF
81 01 7E 01 0B 00 00 ZZ FF
No support
8x 01 7E 54 00 00 0p 0q FF
8x 01 7E 55 00 00 0p 0q FF
No support
8x 01 7E 57 02 FF
8x 01 7E 57 03 FF
8x 01 7E 58 02 FF
8x 01 7E 58 03 FF
8x 01 7E 59 00 FF
8x 01 7E 59 01 FF
8x 01 7E 59 02 FF
8x 01 7E 59 03 FF
8x 01 7E 59 04 FF
8x 01 04 0A 00 FF
8x 01 04 0A 02 FF
8x 01 04 0A 03 FF
8x 01 04 4A 00 00 0p 0q FF
8x 01 04 01 02 FF
8x 01 04 01 03 FF
Comments
p:Memory No(=0-0xF)
pqrs:0x0000 – 0xFFFF
Mirror (Horizontal) on
Mirror (Horizontal) off
ZZ:Zoom Speed(0-7);
No support
pq: Gamma (0x00-0x10)
pq: Chroma (0x00-0x64)
No Support
On
Off
On
Off
Off
Low
Medium
High
Manual
pq(0x00-0x23)
ICR On – Cut filter out B&W
ICR Off – Cut filter in Color
*Zoom and Focus Data:
CAM_Zoom:
Range(0x000–0x6B3)
CAM_Focus: Range (0x0000-0xC000) dependent on Zoom Position
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Page 14 of 16
Zoom SHOT WallVIEW SR
ZoomSHOT Inquiry List (1/1)
Inquiry Command
CAM_PowerInq
Command
8x 09 04 00 FF
CAM_ICRModeInq
8x 09 04 01 FF
CAM_IDInq
CAM_BacklightModeInq
8x 09 04 22 FF
8x 09 04 33 FF
CAM_WBModeInq
81 09 04 35 FF
CAM_FocusModeInq
8x 09 04 38 FF
CAM_AEModeInq
8x 09 04 39 FF
CAM_MemoryInq
CAM_ApertureInq
CAM_RGain
CAM_BGain
CAM_ZoomPosInq
CAM_FocusPosInq
CAM_ShutterPosInq
CAM_Iris
CAM_Gain
CAM_Bright
CAM_LR_Reverse
8x 09 04 3F FF
8x 09 04 42 FF
8x 09 04 43 FF
8x 09 04 44 FF
8x 09 04 47 FF
8x 09 04 48 FF
8x 09 04 4A FF
8x 09 04 4B FF
8x 09 04 4C FF
8x 09 04 4D FF
8x 09 04 61 FF
CAM_Freeze
8x 09 04 62 FF
CAM_PictureEffect
8x 09 04 63 FF
IR_ReceiveInq
8x 09 06 08 FF
TallyInq
8x 09 7E 01 0A FF
PresetSpeedInq
BLK.Enhance
GMA.Enhance
CRM.Enhance
KNE.Enhance
DIS.Enhance
8x 09 7E 01 0B FF
No support
8x 09 7E 54 FF
8x 09 7E 55 FF
No support
8x 09 7E 57 FF
SNR.Enhance
8x 09 7E 58 FF
AGC.Enhance
8x 09 7E 59 FF
Response Packet
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 0p 0q 0r 0s FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 FF
y0 50 03 FF
y0 50 05 FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 FF
y0 50 03 FF
y0 50 0A FF
y0 50 0B FF
y0 50 0p FF
y0 50 00 00 0p 0q FF
y0 50 0p 0q 0r 0s FF
y0 50 0p 0q 0r 0s FF
y0 50 00 0p 0q 0r FF
y0 50 0p 0q 0r 0s FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 FF
y0 50 04 FF
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 00 rr FF
No support
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
No Support
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 04 FF
ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B
Comments
On
Off(Standby)
On - ICR filter Out
Off – ICR filter In
pqrs:0x0000 – 0xFFFF
On
Off
Auto
Manual
One Push WB
Auto
Manual
Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode
p:Preset 0-0xf
Pq:x00-0x1F
pqrs:00-ffff
pqrs:00-ffff
pqr(0x00-0x6B3)
pqrs: Focus Position
pq(0x00-0x23)
pq(0x00-0x11)
pq(0x00-0x24)
pq(0x01-0x64)
On
Off
On
Off
Off
B&W
On
Off
On
Off
rr:Zoom 0x00-0x07
No support
pq: Gamma (0x00-0x10)
pq: Chroma (0x00-0x64)
No support
On
Off
On
Off
Off
Low
Medium
High
Manual AGC Gain
Page 15 of 16
Zoom SHOT WallVIEW SR
***Manual AGC Gain: 0:0dB, 1:3dB, 2:6dB, 3:9dB, 4:12dB, 5:15dB, 6:18dB, 7:21dB, 8:24dB, 9:27dB, 10:30dB, 11:33dB,
12:36dB, 13:39dB & 14:42dB
Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464
www.vaddio.com
©2014 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to
change without notice or obligation. Vaddio, ZoomSHOT, ProductionVIEW, WallVIEW, EZCamera, Quick-Connect and HSDS are trademarks of Vaddio. All
ZoomSHOT
System
Document
Number
342-0651
Rev 342-0651
B
Page 16 of 16
other trademarks
areWallVIEW
property ofSR
their
respective
owners.
Document
Number
Rev B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising