Canon C100 Camcorder Instruction manual

Add to my manuals
162 Pages

advertisement

Canon C100 Camcorder Instruction manual | Manualzz
PUB. DIE-0429-001
HD Camcorder
Instruction Manual
C
Y
P
O
Important Usage Instructions
2
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO DRIPPING OR
SPLASHING.
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
COPYRIGHT WARNING:
Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be
contrary to copyright laws.
FCC NOTICE
HD Camcorder, EOS C100 Systems.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
C
Note: This equipment has been tested and
found to comply with the limits for class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Y
P
O
Use of shielded cable is required to comply with
class B limits in Subpart B of Part 15 of FCC
Rules.
Do not make any changes or modifications to
the equipment unless otherwise specified in the
manual.
If such changes or modifications should be
made, you could be required to stop operation
of the equipment.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success,
NY 11042, U.S.A.
Tel No. (516)328-5600
The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to
disconnect the plug in case of an accident.
CAUTION:
• Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries.
• Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc.
EOS C100 / CA-930 identification plate is located on the bottom.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point, within an equilateral triangle, is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
European Union (and EEA) only.
These symbols indicate that this product is not to be disposed of with your household
waste, according to the WEEE Directive (2002/96/EC), the Battery Directive (2006/66/EC)
and/or your national laws implementing those Directives.
This product should be handed over to a designated collection point, e.g., on an authorized
one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of
waste could have a possible impact on the environment and human health due to potentially hazardous
substances that are generally associated with EEE. Your cooperation in the correct disposal of this product
will contribute to the effective usage of natural resources.
For more information about the recycling of this product, please contact your local city office, waste
authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/
environment.
(EEA: Norway, Iceland and Liechtenstein)
C
Y
P
O
3
Important Safety Instructions
4
In these safety instructions the word “apparatus”
refers to the Canon HD Camcorder EOS C100 and
all its accessories.
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other.
A grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Unplug this apparatus during lightning storms or
when unused for long periods of time.
13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Y
P
O
This Class B digital apparatus complies with Canadian ICES-003.
C
Trademark Acknowledgements
• SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC.
• Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• Apple, Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
• “AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony
Corporation.
• Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• Other names and products not mentioned above may be trademarks or registered trademarks of their
respective companies.
• This device incorporates exFAT technology licensed from Microsoft.
• ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER THAT
COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED
MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2
PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET,
SUITE 300, DENVER, COLORADO 80206.
• This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding
MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal
and non-commercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4
compliant video. No license is granted or implied for any other use for MPEG-4 standard.
Highlights of the EOS C100
The Canon HD Camcorder EOS C100 is a versatile camcorder that combines the power of our latest CMOS
sensor and interchangeable lenses with the convenience of a compact size. The following are just some of the
many features that will help turn your creative vision into reality.
5
HD Recording
Large Super 35mm CMOS sensor and DIGIC DV
III image processor
The camcorder is equipped with a large Super
35mm CMOS sensor that captures video at an
effective pixel count of 8.29 megapixels
(3840x2160). Combined with the DIGIC DV III image
processor, the camcorder offers a center resolution
of 1,000 TV lines*. Furthermore, thanks to its fast
scanning speed, the camcorder produces
spectacular video with true-to-life color reproduction
while reducing noise and “rolling shutter” artifacts.
In addition, using double slot recording (A 41) lets
you record the same clip simultaneously to both SD
cards.
Enhanced automatic functions
The camera features a variety of automatic functions
to support a simple one-person operation. These
include Push auto iris (A 60) for automatic aperture
adjustment as long as you press and hold the
button, automatic white balance (A 63) to let the
camcorder continuously adjust the optimal white
balance setting, and One-shot AF (A 64) to let the
camcorder focus automatically one time.
* Varies depending on the lens used.
Interchangeable lenses
Enjoy the freedom and creative versatility of using
interchangeable lenses to achieve exactly the look
you want. The camcorder features an EF lens mount
allowing you to use a huge variety of high-quality
Canon EF lenses, including the new high-end EF
Cinema lens series, as well as other lenses.
C
Superb HD video
The camcorder offers you a whole array of options
when it comes to the video configuration of your
recordings. By controlling the system frequency
(50.00 Hz recordings or 59.94 Hz recordings), bit
rate, resolution and frame rate of your recordings
you can select a video configuration to suit your
needs from a total of 24 different combinations.
Operability and Adaptability
Freely customizable compact design
At its most compact configuration, the camcorder
offers convenient and hassle-free hand-held
operation. Modular components let you expand
your options. The handle unit, for example, adds
advanced audio capabilities allowing for simple oneperson operation (A 29).
Recording media
The camcorder supports all the latest types of
Secure Digital (SD) cards. You can even make
lengthy recordings without worry because the
camcorder features two SD card slots. When one
SD card becomes full, the recording will
automatically continue on the other one when you
use relay recording (A 41).
Versatile Artistic Expression
Y
P
O
Custom picture settings
With custom picture settings (A 88), you can enjoy
unparalleled image control to deliver the look you
want by adjusting parameters, such as gamma and
sharpness. The camcorder also features a new,
easy interface that lets you adjust the gamma curve
and white balance using an intuitive graph. The
custom picture settings can be saved onto an SD
card, which allows multiple C100 camcorders to use
the same settings.
Wide DR gamma and Canon Log gamma (A 49,
97) for cinematic recordings
Wide DR gamma is a gamma curve that offers an
impressive dynamic range and was developed with
playback on an HDTV in mind. Video editing is easily
accessible since this setting does not require any
post-production.
Using the Canon Log gamma, you can get
recordings with amazing dynamic range, allowing
you to realize in post-production the artistic vision
you desire.
6
Advanced Professional Features
Other Functions
Customization
The camcorder features several customization
options. You can assign often-used functions to
assignable buttons (A 85) so that you can call up
those functions with the press of a single button. You
can also register frequently-used menu settings in an
easy-to-access personal menu (My Menu, A 28).
Custom functions (A 98) and custom onscreen
displays (A 98) give you even more freedom to
control many aspects of the camcorder’s operation.
Save custom picture and menu settings to an SD
card (A 99) so that you can transfer your setting
preferences to other C100 camcorders in order to
use them in the same way.
Audio
When recording at the highest bit rate, you have the
option to record sound as 2-channel linear PCM
audio (16-bit/48 kHz). You can use the built-in
microphone, ∅ 3.5 mm MIC terminal or the two XLR
audio input terminals (with phantom power supply)
when recording.
Time code/User bit output
The internal camcorder-generated time code can be
output from the HDMI OUT terminal for easy logging
and referencing (A 134). Additionally, the
camcorder can output also the user bit (A 72).
C
LCD screen and viewfinder
The LCD screen and viewfinder both have 100%
frame coverage, which will ensure that you can
accurately check that your shots are framed how you
want them.
Video scopes
Check the brightness of the image using the
waveform monitor (A 80) or the focus using the
edge monitor (A 81).
Added and improved functionality
Other functions include the ability to down-convert
your recordings to standard definition (MPEG-2) in
the camcorder itself (A 108), and the Intelligent
System-compatible battery pack (A 153).
Y
P
O
Table of Contents
7
1. Introduction 11
3. Recording 45
About this Manual 11
Conventions Used in this Manual 11
Supplied Accessories 13
Names of Parts 14
Grip Unit 19
Handle Unit 20
Recording Video 45
Preparing to Record 45
Recording 45
Onscreen Displays 48
CINEMA Preset 49
Video Configuration: System Frequency, Bit Rate
and Frame Rate 50
Changing Main Camera Functions with the
Joystick 52
Shutter Speed 53
Changing the Shutter Mode 54
Adjusting the Shutter Value 54
Flicker Reduction 55
ISO Speed/Gain 56
Changing the ISO Speed or Gain Settings 56
Adjusting the ISO/Gain Value 57
ND Filter 58
Adjusting the Aperture 59
Manual Aperture Control 59
Momentary Automatic Aperture - Push Auto
Iris 60
White Balance 62
Custom White Balance 62
Preset White Balance Settings 63
Color Temperature Setting 63
Auto White Balance 63
Adjusting the Focus 64
Manual Focus 64
One-Shot AF 64
Using the Focus Assistance Functions 66
Onscreen Markers and Zebra Patterns 67
Displaying Onscreen Markers 67
Displaying Zebra Patterns 68
Setting the Time Code 69
Selecting the Running Mode 69
Selecting Drop or Non-Drop Frame 70
Putting the Time Code Display on Hold 70
Setting the User Bit 72
2. Preparations 21
Preparing the Power Supply 21
Using a Battery Pack 21
Using a Household Power Outlet 24
Turning the Camcorder On and Off 24
Date, Time and Language Settings 25
Setting the Date and Time 25
Changing the Time Zone 25
Displaying the Date and Time while Recording 26
Changing the Language 26
Using the Menus 27
Selecting an Option from the Menu 27
Using the Customized Submenu (My Menu) 28
Preparing the Camcorder 29
Preparing the Lens 29
Attaching and Removing the Handle Unit 32
Using the Viewfinder 32
Using the LCD Panel 33
Adjusting the Viewfinder/LCD Screen 33
Using a Tripod 34
Removing and Attaching the Grip Unit 34
Attaching a Shoulder Strap 35
Removing and Attaching the Terminal Covers 36
The Camcorder’s Cooling System 36
Using an SD Card 38
SD Cards Compatible for Use with the
Camcorder 38
Inserting and Removing an SD Card 39
Checking the Status of the SD Card Slots 39
Initializing an SD Card 40
Switching Between the SD Card Slots 41
Selecting the SD Card Recording Method 41
Checking the Available Recording Time 42
Recovering Data on an SD Card 42
Adjusting the Black Balance 43
C
Y
P
O
8
Recording Audio 73
Connecting an External Microphone or External
Audio Input Source to the Camcorder 73
Using the Built-in Microphone or an External
Microphone Connected to the MIC
Terminal 73
Adjusting the Audio Level for the MIC Terminal 74
Using Audio Input from the XLR Terminals 76
Adjusting the Audio Level for the XLR
Terminals 77
Monitoring the Audio with Headphones 78
Color Bars/Audio Reference Signal 79
Recording Color Bars 79
Recording an Audio Reference Signal 79
Video Scopes 80
Displaying a Video Scope 80
Configuring the Waveform Monitor 80
Configuring the Edge Monitor 81
Reviewing a Recording 82
Pre-recording Mode 83
C
4. Customization 85
Assignable Buttons 85
Changing the Assigned Function 85
Using an Assignable Button 86
Custom Picture Settings 88
Selecting Custom Picture Files 88
Editing a Custom Picture File’s Settings 89
Resetting the current file’s settings to default
values 89
Renaming Custom Picture Files 89
Protecting Custom Picture Files 89
Transferring Custom Picture Files 90
Available Custom Picture Settings 91
Simplified Graphical Interface 96
Canon Log Gamma 97
Customizing Functions and Onscreen
Displays 98
Customizing Functions 98
Customizing Onscreen Displays 98
Saving and Loading Camera Settings 99
Saving Camera Settings to an SD Card 99
Loading Camera Settings from an SD Card 99
5. Playback 101
Playback 101
Clip Index Screen 101
Playing Back Clips 102
Onscreen Displays 103
Playback Controls 104
Adjusting the Volume 104
Clip Operations 106
Using the Clip Menu 106
Copying Clips 106
Deleting Clips 107
Converting Clips to Standard Definition 108
Deleting SD Movies 110
6. External Connections 111
Y
P
O
Video Output Configuration 111
Connecting to an External Monitor 112
Connection Diagram 112
Using the HDMI OUT Terminal 112
Using the AV OUT Terminal 113
SD Output 113
Superimposing Onscreen Displays to Appear on
an External Monitor 114
Audio Output 115
Synchronizing the Video with the Audio being
Monitored 115
Selecting the Audio Channel 115
Selecting the Output Level of the AV OUT
Terminal 116
Saving Clips to a Computer 117
Connection Diagram 117
7. Photos 119
Taking Photos 119
Taking Photos in CAMERA Mode 119
Capturing Photos in MEDIA Mode 119
Photo Playback 121
Displaying the [Photos] Index Screen 121
Viewing Photos 121
Photo Operations 122
Using the Photo Menu 122
Copying Photos 122
Deleting Photos 123
Copying Custom Picture Files 125
9
8. Additional Information 127
Menu Options 127
Displaying the Status Screens 135
Resetting the File Numbering 141
Troubleshooting 142
List of Messages 145
Handling Precautions 148
Maintenance/Others 151
Optional Accessories 152
Specifications 155
Index 158
C
Y
P
O
10
C
Y
P
O
1
Introduction
11
About this Manual
Thank you for purchasing the Canon EOS C100. Please read this manual carefully before you use the camcorder
and retain it for future reference. Should the camcorder fail to operate correctly, refer to Troubleshooting
(A 142).
Conventions Used in this Manual
•
IMPORTANT: Precautions related to the camcorder’s operation.
•
NOTES: Additional topics that complement the basic operating procedures.
• A: Reference page number.
• The following terms are used in this manual.
“Screen” refers to the LCD screen and the viewfinder screen.
“SD card” refers to an SD, SDHC or SDXC card.
• Photographs in the manual are simulated pictures taken with a still camera. Some screenshots have been
altered to make them easier to read.
• Illustrations in the manual show the Canon EOS C100 camcorder with a Canon EF 24-70mm f/2.8 L II USM
lens attached.
C
Y
P
O
About this Manual
12
The > arrow is used to abbreviate menu
selections. For a detailed explanation on how to
use the menus, refer to Using the Menus
(A 27). For a concise summary of all available
menu options and settings, refer to the appendix
Menu Options (A 127).
Operating modes
indicates that a function is available in the
operating mode indicated and
indicates
that the function is not available. For a detailed
explanation, refer to Turning the Camcorder On
and Off (A 24).
Setting the Time Code
The camcorder generates a times code signal and embeds it in your recordings. You can output the time code
along with video output from the HDMI OUT terminal (A 134). For 59.94 Hz recordings, you can also select
between a drop frame and non-drop frame time code.
69
Operating modes:
Selecting the Running Mode
[¤ TC/UB Setup]
You can select the running mode of the camcorder s time code.
[Time Code]
1 Open the time code [Mode] submenu.
[¤ TC/UB Setup] > [Time Code] > [Mode]
[Mode]
2 Select the desired option and then press the joystick.
€ If you selected [Regen.], you do not need to perform the rest of this
procedure. If you selected [Preset] and would like to set the time
code s initial value, see the following section Setting the Time Code s
Initial Value.
Y
P
O
3 After you select [Preset], open the time code [Run] submenu.
[¤ TC/UB Setup] > [Time Code] > [Run]
[Preset]
[¤ TC/UB Setup]
[Time Code]
4 Select the desired option and then press the joystick.
Options
[Preset]:
C
The time code starts from an initial value you can select in
advance. The default initial time code is 00:00:00.00. The time
code s running mode depends on the [Run] setting.
[Rec Run]: The time code runs only while recording so clips
recorded consecutively on the same SD card will have
continuous time codes.
[Free Run]:The time code starts running the moment you press
the joystick to select this option and keeps running
regardless of the camcorder s operation.
[Regen.]: The camcorder will read the selected SD card and the time code
will continue from the last recorded time code on the SD card.
The time code runs only while recording so clips recorded
consecutively on the same SD card will have continuous time
codes.
[Run]
[Rec Run]
Setting the Time Code s Initial Value
[¤ TC/UB Setup]
If you set the time code mode to [Preset], you can set the initial value of
the time code.
[Time Code]
1 Open the time code [Setting] submenu.
[¤ TC/UB Setup] > [Time Code] > [Setting]
[Setting]
2 Select [Set] and then press the joystick.
€ The time code setting screen appears with an orange selection frame
indicating the hours.
When a procedure requires selecting an option,
the available options are listed within or after the
procedure. Brackets [ ] are used to refer to menu
options as they are displayed on screen.
When a function requires the use of the menu,
the quick reference shows the submenus and,
when applicable, the default setting for the menu
item. The example illustration indicates that you
can find the function by selecting the [¤ TC/
UB Setup] menu and then the [Time Code]
menu item.
Supplied Accessories
Supplied Accessories
The following accessories are supplied with the camcorder.
13
Handle Unit
Grip Unit1
BP-955 Battery Pack
(incl. terminal cover)
CA-930 Compact Power Adapter
(incl. power cord)
Body Cap1
Thumb Rest
SS-1200 Shoulder Strap
DC-930 DC Cable
Adapter Base for 0.64 cm (1/4 in.)
Tripods
1
2
C
Tape Measure Hook1
Y
P
O
PIXELA Software CD-ROM2
Comes pre-attached to the camcorder.
Use Data Import Utility to transfer your clips to a computer. Refer to Saving Clips to a Computer (A 117). The CD-ROM
includes the instruction manual of the software (on PDF file).
Names of Parts
Names of Parts
14
5
6
7
8
9
10
11
12
1
2
3
4
Y
P
O
13 14 15 16
C
1
2
3
4
5
6
7
MAGN. (magnification) button (A 66)/
Assignable button 8 (A 85)
PEAKING button (A 66) /
Assignable button 9 (A 85)
ZEBRA button (A 68)/
Assignable button 10 (A 85)
WFM (waveform monitor) button (A 80)/
Assignable button 11 (A 85)
Tape measure hook
Use the hook to accurately measure the distance
from the focal plane.
Q switch (A 24)
Strap mount (A 35)
8
9
10
11
12
13
14
Exhaust ventilation outlet (A 36)
STATUS button (A 135)
Å (white balance adjustment) button (A 62)
WB (white balance) button (A 62)
CUSTOM PICTURE button (A 88)
ND FILTER dial (A 58)
PUSH AUTO IRIS (momentary automatic aperture)
button (A 60)/Assignable button 12 (A 85)
15 ISO/GAIN button (A 57)/Assignable button 13
(A 85)
16 SHUTTER button (A 54)/Assignable button 14
(A 85)
Names of Parts
15
17
18
19
20
21
24
25
22
26
23
27
17
18
19
20
EXT (modular unit) terminal (A 32)
MIC (microphone) terminal (A 73)
× (headphone) terminal (A 78)
REMOTE terminal
For connecting commercially available remote
controllers.
21 USB terminal (A 117)
C
Y
P
O
22
23
24
25
26
27
HDMI OUT terminal (A 112)
DC IN terminal (A 24)
Grip Unit connection terminal (A 34)
Grip Unit attachment thread (A 34)
BATTERY RELEASE latch (A 22)
Air intake vent (A 36)
Names of Parts
16
29
30
31
32
33
34
35
28
36
28
29
30
31
32
33
34
START/STOP button (A 45)
EF Lens mount index (A 29)
EF-S Lens mount index (A 29)
EF Lens lock pin (A 29)
Lens release button (A 30)
EF Lens mount (A 29)
EF Lens contacts (A 29)
C
Y
P
O
35 ONE-SHOT AF (focus automatically once) button
(A 64)/Assignable button 15 (A 85)
36 AV OUT terminal (A 113)
Names of Parts
LCD panel fully open
37
LCD panel raised 90° up and turned left
38
17
39
40 46
47
41 48
49
50
53
54
55
56
57
51
52
42
37
38
39
40
41
42
43
44
45
46
47
43 44 45
C
Dioptric adjustment lever (A 32)
Viewfinder (A 32, 33)
CANCEL button (A 27)
MENU button (A 27)
u (review recording) button (A 82)/
INDEX button (A 102)
LCD screen (A 33)
Battery compartment
SLOT SELECT (SD card slot selection) button
(A 41, 102)
DISP. (display) button (A 48, 103)/BATT. INFO
(battery information) button (A 23)
Ø (fast reverse playback) button (A 104)/
Assignable button 1 (A 85)
Ú (skip backward) button (A 104, 121)/
Assignable button 4 (A 85)
58
Y
P
O
48
49
50
51
52
53
54
55
56
57
58
Speaker (A 104)
RESET button (A 144)
SD card 2 access indicator (A 39)
SD card compartment cover
SD card slot 2 (A 39)
Ò (play/pause) button (A 102, 121)/
Assignable button 2 (A 85)
× (fast playback) button (A 104)/
Assignable button 3 (A 85)
Ù (skip forward) button (A 104, 121)/
Assignable button 6 (A 85)
Ñ (stop) button (A 102, 121)/
Assignable button 5 (A 85)
SD card 3 access indicator (A 39)
SD card slot 3 (A 39)
Names of Parts
18
60
59
59
Focal plane mark
60 Accessory shoe with mounting hole for
0.64 cm (1/4 in.) screws
Cold shoe for attaching the supplied handle unit or
other accessories, such as the optional
VL-10Li II Battery Video Light.
C
Y
P
O
63
64
61
62
61 TB-1 Tripod Base for tripods with 0.95 cm (3/8 in.)
screws (A 34)
62 Tripod socket (A 34)
63 Attachment sockets for the optional TA-100 Tripod
Adapter (A 34)
64 Tripod base screws (A 34)
Names of Parts
Grip Unit
6
1
2
3
4
7
5
8
1
2
3
4
5
6
7
8
MAGN. (magnification) button (A 66)/
Assignable button 7 (A 85)
Strap mount (A 35)
Control dial (A 59)
START/STOP button (A 45)
Grip belt (A 35)
Joystick (A 27)
Connection plug (A 34)
Lock screw (A 34)
C
Y
P
O
19
Names of Parts
Handle Unit
1
20
2
345
6
7
8
16
9
17
10
12
11
Y
P
O
13
C
1
2
3
4
5
6
7
8
9
10
11
12
Microphone holder (A 73)
Microphone lock screw (A 73)
Front tally lamp (A 45)
Cold accessory shoe
Rear tally lamp (A 45)
START/STOP lock (C) lever (A 47)
START/STOP button (A 45)
Mounting hole for 0.64 cm (1/4 in.) screws
Lock screw (A 32)
Protective cover for audio controls
Built-in microphone (A 73)
(audio level) dials for CH1 (left) and CH2
(right) (A 74, 77)
14
15
13 Audio levelswitches for CH1 (left) and CH2 (right)
(A 74, 77)
14 XLR terminal switches for CH1 (left) and CH2
(right) (A 76)
15 AUDIO IN (audio input selection) switches for CH1
(left) and CH2 (right) (A 73, 76)
16 Microphone cable clamp (A 73)
17 XLR terminals CH1 (right) and CH2 (left) (A 73)
2
Preparations
21
Preparing the Power Supply
You can power the camcorder using a battery pack or directly using the compact power adapter. If you connect
the compact power adapter to the camcorder while a battery pack is attached, the camcorder will draw power
from the power outlet.
Charge battery packs before use. For approximate charging times and recording/playback times with a fully
charged battery pack, refer to Charging Times (A 153) and Recording and Playback Times (A 153).
Using a Battery Pack
You can power the camcorder using the supplied BP-955 or an optional BP-950G, BP-970G or BP-975 Battery
Pack. The BP-955 and BP-975 are compatible with Intelligent System, meaning that you can check the
remaining battery time.
Charging the Battery Pack
Charge battery packs using the supplied DC-930 Compact Power Adapter.
Before charging, disconnect the DC cable from the compact power adapter
and remove the terminal cover of the battery pack.
Y
P
O
1 If the DC cable is connected to the compact power adapter, disconnect it.
• Charging will not start while the DC cable is connected to the compact
power adapter.
C
2 Connect the power cord to the compact power adapter.
3 Plug the power cord into a power outlet.
CHARGE indicator
4 Attach the battery pack to the compact power adapter.
• Press lightly and slide the battery pack in the direction of the arrow until it clicks.
• The CHARGE indicator starts flashing and also indicates the battery pack’s approximate charge. The
indicator will stay on when charging has completed.
0-34%: Flashes once per second
35-69%: Flashes twice per second
70-99%: Flashes 3 times per second
5 When charging has completed, remove the battery pack from the compact power adapter.
6 Unplug the power cord from the power outlet and disconnect it from the compact power adapter.
IMPORTANT
• Do not connect to the compact power adapter any product that is not expressly recommended for use with this
camcorder.
NOTES
• We recommend charging the battery pack in temperatures between 10 ºC and 30 ºC (50 ºF and 86 ºF).
Outside the temperature range of 0 ºC to 40 ºC (32 ºF to 104 ºF), charging will not start.
• If there is a malfunction with the compact power adapter or battery pack, the charge indicator will go out and
charging will stop.
• For handling precautions regarding the battery pack, refer to Battery Pack (A 148).
Preparing the Power Supply
22
• Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day
before, to ensure a full charge.
• We recommend that you prepare battery packs to last 2 to 3 times longer than you think you might need.
• To charge the battery pack, disconnect the DC cable from the compact power adapter.
Attaching the Battery Pack
1 Set the Q switch to OFF.
2 Insert the battery pack all the way into the compartment as shown
in the illustration and press it gently toward the left until it clicks.
Removing the Battery Pack
C
Y
P
O
1 Set the Q switch to OFF.
2 Push the BATTERY RELEASE latch in the direction of the arrow.
While holding it down, slide the battery pack toward the right and
then pull it out.
Preparing the Power Supply
Checking the Remaining Battery Charge
When the camcorder is turned on, you can check the remaining battery charge by looking at any recording/
playback screen or the [Battery/Hour Meter] status screen (A 138). When the camcorder is turned off, use one
of the following methods to check the approximate remaining battery charge of a battery compatible with
Intelligent System.
Press the CHECK button on the battery pack. An indicator will light for
approximately 3 seconds and show the approximate remaining battery
charge.
0-25%
26-50%
51-75%
76-100%
CHECK button
0
100%
Battery charge indicator
Press the BATT. INFO button to display the approximate remaining
battery charge for about 5 seconds. Depending on the battery life, the
battery information may not be displayed.
C
Y
P
O
NOTES
• The first time you use a battery pack, fully charge it and then use the camcorder until the battery pack is
completely exhausted. Doing so will ensure that the remaining recording time will be displayed accurately in
the various recording/playback screens.
• Repeatedly charging and discharging the battery pack will eventually shorten its battery life. You can check the
battery life on the [Battery/Hour Meter] status screen (A 138) or the battery information screen (press the
BATT. INFO button while the camcorder is turned off). Fully charging the battery pack and then discharging it
will give you a more accurate reading.
• USA and Canada only: The Lithium ion/polymer battery that powers the product is recyclable.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
23
Preparing the Power Supply
Using a Household Power Outlet
24
You can also power the camcorder directly
from a power outlet using the supplied CA-930
Compact Power Adapter and DC-930 DC
Cable.
1 Set the Q switch to OFF.
2 Connect the DC cable to the DC IN
terminal on the camcorder.
3 Connect the power cord to the compact
power adapter and plug it into a power
outlet.
4 Connect the DC cable to the compact
power adapter.
IMPORTANT
• Turn off the camcorder before connecting or
disconnecting the compact power adapter.
DC IN
terminal
NOTES
• When using the camcorder with a household
power outlet, you can change the battery pack while the power is on.
Turning the Camcorder On and Off
C
Y
P
O
The camcorder has two operating modes: CAMERA (
) mode for making recordings and MEDIA (
mode for playing back recordings. Select the operating mode using the Q switch.
To turn on the camcorder
Set the Q switch to CAMERA for
mode.
CAMERA mode
To turn off the camcorder
Set the Q switch to OFF.
mode or MEDIA for
MEDIA mode
)
Date, Time and Language Settings
Date, Time and Language Settings
Setting the Date and Time
You will need to set the date and time of the camcorder before you can start using it. When the camcorder’s
clock is not set, the [Date/Time] screen will appear automatically with the first field selected (month or day,
depending on the country/region of purchase).
Operating modes:
1 Push the joystick up/down to change the month/day then push it right to move to the next field.
• To move to the next field you can also press the joystick itself.
2 Change the rest of the fields in the same way.
3 Select [Set] and then press the joystick to start the clock and close the screen.
Y
P
O
NOTES
• You can change the date format and the clock format (12/24 hours) with the [w Other Functions] > [Set
Clock] > [Date Format] setting.
• You can also change the date and time later on (not during the initial setup) with the [w Other Functions] >
[Set Clock] > [Date/Time] setting.
• When the built-in rechargeable lithium battery is exhausted, the date and time setting may be lost. In such
case, recharge the built-in lithium battery (A 150) and set the time zone, date and time again.
C
Changing the Time Zone
Change the time zone to match the time zone of your location. The default
setting is [UTC-05:00 New York] or [UTC+01:00 Central Europe],
depending on the country/region of purchase. The time zones are based
on Coordinated Universal Time (UTC).
Operating modes:
1 Press the MENU button.
2 Push the joystick up/down to select [w Other Functions].
[w Other Functions]
[Time Zone]
[UTC-05:00 New York]
or
[UTC+01:00 Central Europe]*
* Depending on the country/region
of purchase.
3 Select [Time Zone] in a similar fashion.
4 Push the joystick up/down to change the time zone.
5 Press the joystick to set the time zone and then press the MENU button to close the menu.
25
Date, Time and Language Settings
Displaying the Date and Time while Recording
[£ LCD/VF Setup]
You can display the date and time on the screen.
26
[Custom Display 2]
Operating modes:
[Date/Time]
1 Press the MENU button.
2 Push the joystick up/down to select [£ LCD/VF Setup].
[Off]
3 Select [Custom Display 2] and then [Date/Time] in a similar
fashion.
4 Push the joystick up/down to select the information to display.
• Select [Off] to record without displaying the date and time.
5 Press the joystick and then press the MENU button to close the menu.
• The selected date/time display will appear at the bottom left of the screen.
Changing the Language
The default language of the camcorder is English. You can change it to
German, Spanish, French, Italian, Polish, Russian, Simplified Chinese,
Korean or Japanese. Please note that some settings and screens will be
displayed in English, regardless of the language setting.
Operating modes:
1 Press the MENU button.
C
Y
P
O
[w Other Functions]
[Language !]
[English]
2 Push the joystick up/down to select [w Other Functions].
3 Select [Language !] in a similar fashion.
4 Push the joystick up/down to select a language.
5 Press the joystick to change the language and then press the MENU button to close the menu.
Using the Menus
Using the Menus
In
mode, many of the camcorder’s functions can be adjusted from the menu for general settings, which
opens after pressing the MENU button. You can also register frequently used menu settings in a customized
submenu (My Menu) for easy access. In
mode, press the MENU button to open the menu for general
settings or press the joystick to open the clip menu for clip operations. For details about the available menu
options and settings, refer to Menu Options (A 127).
Operating modes:
CANCEL button
Press to return to the previous menu or to stop some
operations that are in progress.
MENU button
Press to open the menu and then press again to close
the menu after adjusting desired settings.
Joystick
Push the joystick to move the orange selection frame in
the menu. Then, press the joystick itself to select the
menu item indicated by the orange selection frame.
Selecting an Option from the Menu
Y
P
O
The following is a step-by-step explanation of how to select an option from the menu. In the procedures
throughout the rest of this manual, opening and closing the menu is assumed and not included in the procedure.
1 Press the MENU button.
C
• The menu opens with the orange selection frame indicating the menu item that was selected the previous
time the menu was closed (unless the camcorder was turned off).
2 Push the joystick up/down to select the desired submenu.
3 Push the joystick right or press the joystick.
• The orange selection frame will appear on a menu item in the submenu.
• Press the CANCEL button, push the joystick left, or select [L] to return to the previous submenu.
4 Push the joystick up/down to select the desired menu item.
• If a submenu contains many menu items, a scroll bar will appear on the right side of the submenu indicating
that you must scroll up or down to see other menu items.
• A Ð mark next to a menu item indicates another submenu. Repeat steps 3 and 4.
5 Push the joystick right or press the joystick.
• The orange selection frame will appear on a setting option.
• Press the CANCEL button to return to the previous submenu.
6 Push the joystick up/down to select the desired setting option and then press the joystick.
• Depending on the menu item, additional selections may be necessary.
7 Press the MENU button to close the menu.
NOTES
• Unavailable items may appear grayed out.
• Pressing the MENU button at any time closes the menu.
• You can check some of the current menu settings on the status screens (A 135).
27
Using the Menus
Using the Customized Submenu (My Menu)
28
You can register up to 14 frequently used menu settings under the My Menu submenu for easy access.
Furthermore, if you set an assignable button to [My Menu] (A 85), you can press the button to access your
registered menu settings even faster and more easily.
Adding Menu Settings
[
1 Open the My Menu [Register] screen.
[
My Menu] > [Edit] > [Register]
• The menu will change to blue to indicate you are selecting menu
settings to add to the My Menu submenu.
My Menu]
[Edit]
[Register]
2 Navigate the menus to find the menu setting you want to add and then
press the joystick.
3 Select [OK] and then press the joystick twice.
• The menu setting you registered will now appear under the [My Menu] submenu.
Rearranging Menu Settings
[
1 Open the My Menu [Move] screen.
[
My Menu] > [Edit] > [Move]
My Menu]
[Edit]
2 Push the joystick up/down to select the setting you want to move and
then press the joystick.
• An orange icon will appear next to the setting you selected to
move.
C
Y
P
O
[Move]
3 Push the joystick up/down to move the setting to the desired position and then press the joystick.
Removing Menu Settings
[
1 Open the My Menu [Delete] screen.
[
My Menu] > [Edit] > [Delete]
My Menu]
[Edit]
2 Push the joystick up/down to select the setting you want to remove and
then press the joystick.
[Delete]
3 Select [OK] and then press the joystick twice.
Resetting the My Menu Submenu
1 Reset all the menu settings registered to the My Menu submenu.
[
My Menu] > [Edit] > [Reset All]
[
My Menu]
[Edit]
2 Select [OK] and then press the joystick twice.
[Reset All]
Preparing the Camcorder
Preparing the Camcorder
This section outlines the basic preparations for the camcorder such as attaching a lens and attaching the
modular units (handle unit, grip unit, etc.) to the camcorder. The modular units extend the camcorder's
functionality so you can choose the configuration that best fits your needs and shooting conditions.
Configuration with handle: Attach
the handle unit to use the built-in
microphone, XLR terminals,
microphone holder, etc. (A 73)
Preparing the Lens
Light configuration with grip
for hand-held shooting
C
Y
P
O
Minimal configuration with
thumb rest. The joystick (A 27),
control dial (A 59) and MAGN.
button/Assignable button 7
(A 85) are not available to
operate the camcorder.
As much as possible, attach and remove the lens quickly and in a clean environment free of dust. Refer also to
the instruction manual of the lens used.
IMPORTANT
• When attaching/removing a lens, avoid direct sunlight or strong light sources. Also, be careful not to drop the
camcorder or lens.
NOTES
• Be careful not to touch the lens mount or any components inside the lens mount area.
• Replace the body cap to the lens mount immediately after removing the lens from the camcorder.
• Keep the body cap clean and free from dust or dirt particles.
Attaching an EF Lens
1 Set the Q switch to OFF.
2 Remove the body cap from the camcorder and any dust
caps from the lens.
3 Attach the lens to the camcorder and turn the lens in the
direction of the arrow until it clicks in place.
• EF lenses: Align the red mark on the lens with the red
EF Lens mount index mark on the camcorder.
• EF-S lenses: Align the white mark on the lens with the
white EF-S Lens mount index mark on the camcorder.
29
Preparing the Camcorder
30
NOTES
• Turning on the image stabilization function of an EF lens may reduce the effective usage time of the battery
pack. When image stabilization is not necessary, for example if the camcorder is fixed to a tripod, it is
recommended to turn it off.
• On some EF lenses equipped with autofocus (AF) function, the focus ring will be disabled when the focus
mode switch is set to AF. In such case, set the focus mode switch to MF.
• Depending on the lens used, you may experience one or more of the following limitations.
- The lens model name may be shortened when displayed on the screen.
- You may not be able to use the focus preset function (super telephoto lenses).
- You may not be able to use the power zoom function of the lens.
Removing an EF Lens
1 Set the Q switch to OFF.
2 Hold down the lens release button and turn the lens all the
way in the direction of the arrow until it stops.
3 Remove the lens and replace the body cap to the
camcorder and the dust cap to the lens.
Peripheral Illumination Correction
Depending on the characteristics of the lens used, the image
around the corners of the picture may seem darker due to light
fall-off or peripheral illumination drop. If the camcorder has
correction data available for the EF lens used, it can apply this
correction data to compensate as necessary.
Operating modes:
C
Y
P
O
1 Attach the lens you want to use.
[~ Camera Setup]
2 Open the peripheral illumination correction screen.
[~ Camera Setup] > [Periph. Illum. Corr.]
[Periph. Illum. Corr.]
• If correction data is available, the lens model name will appear on the
screen.
[Off]
• If correction data is not available, [Periph. Illum. Corr.] will appear
grayed out. Visit your local Canon Web site and check if there is
correction data available for the lens you are using. If so, download the necessary update package and
upgrade the camcorder’s firmware following the instructions supplied therein.
3 Select [On] and then press the joystick.
• As long as [~ Camera Setup] > [Periph. Illum. Corr.] is set to [On], the camcorder will automatically apply
the appropriate correction data.
Correction for EF-S Lenses
The peripheral illumination fall-off may be more pronounced with EF-S lenses than with EF lenses. To prevent
this, when you use an EF-S lens, you can change the sensor area that is used for producing the image.
Preparing the Camcorder
1 Open the [EF-S Lens] submenu.
[~ Camera Setup] > [EF-S Lens]
[~ Camera Setup]
2 Select [On] and then press the joystick.
•
will appear at the lower center of the screen.
• When [EF-S Lens] is set to [On], the image is enlarged digitally by
approximately 1.04%, slightly affecting the image quality. In most
cases, using the default [Off] setting is recommended.
[EF-S Lens]
[Off]
NOTES
• About lens correction data:
- The camcorder contains a register of correction data for compatible lenses that were available at the time
the camcorder went on sale. Correction data for future lenses will be made available as part of the regular
updates released for the camcorder’s firmware. For more details, visit your local Canon Web site.
- Depending on the recording conditions, noise may appear in the periphery of the image as a result of the
correction.
- The level of correction will be lower for lenses that cannot provide distance information.
- The level of correction will be lower the higher the ISO speed/gain setting used.
- No correction will be applied when correction data is not available for the lens attached.
- When using non-Canon lenses, peripheral illumination cannot be corrected. Even if the [Periph. Illum. Corr.]
setting is available (not grayed out), setting it to [Off] is recommended.
Updating the Firmware of an EF Lens
Y
P
O
You can update the lens firmware of an EF lens using the camcorder. For details about firmware updates for EF
lenses, visit your local Canon Web site.
C
1 Insert the SD card containing the lens firmware update into SD card
slot A.
[w Other Functions]
2 Attach to the camcorder the lens you wish to update and open the
[Lens Firmware]
[Lens Firmware] submenu.
[w Other Functions] > [Lens Firmware]
• The current lens firmware version will appear on the screen.
• If the [Lens Firmware] submenu is grayed out, the attached lens may not support firmware updates or the
SD card in SD card slot A may not contain a valid lens firmware file. Check the lens and SD card and repeat
the procedure from the beginning.
3 Select [OK] and then press the joystick.
4 Select the lens firmware file (file extension .LFU) and then press the joystick.
5 Select [OK] and then press the joystick.
• The lens firmware will be updated. Once in progress, the lens firmware update cannot be canceled.
6 When the confirmation message appears, press the joystick.
IMPORTANT
• Be sure to observe the following precautions while the lens firmware is being updated.
- Do not disconnect the power source or turn off the camcorder.
- Do not remove the lens.
- Do not operate any buttons or controls on the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
NOTES
• The lens firmware cannot be updated while pre-recording is activated.
31
Preparing the Camcorder
• We recommend that you power the camcorder from a household power outlet using the compact power
adapter or use a sufficiently charged battery pack.
• When using an optional EF Extender, remove the Extender before performing the procedure.
32
Attaching and Removing the Handle Unit
The handle unit extends the camcorder’s audio capabilities, adding XLR terminals as well as a built-in stereo
microphone.
Attaching the Handle Unit
1 Set the Q switch to OFF.
2 Insert the attachment base at the bottom of the handle
unit to the camcorder’s accessory shoe.
3 Tighten the handle unit’s lock screw while gently pressing
it down.
4 Connect the handle unit’s cable to the camcorder’s EXT
terminal, aligning the Í marks.
Removing the Handle Unit
1 Set the Q switch to OFF.
Y
P
O
2 Disconnect the handle unit's cable.
• Pull back the metallic tip of the cable to release the
cable and then disconnect the cable from the terminal.
C
3 Loosen the handle unit's lock screw and gently slide out
the handle unit from the accessory shoe.
NOTES
• You can use the accessory shoe or the socket for 0.64 cm (1/4 in.) screws on the handle unit to attach a
variety of commercially available accessories.
Using the Viewfinder
Dioptric Adjustment
Turn on the camcorder and adjust the dioptric adjustment
lever.
Dioptric
adjustment
lever
Preparing the Camcorder
Using the LCD Panel
1 Pull the LCD panel 90° up.
2 Rotate the LCD panel 180° left.
33
3 Push down the LCD panel to adjust it to the desired angle of view.
NOTES
• You can set the LCD screen to black & white (A 33).
• When you use a commercially available lens adapter and the image on
the screen is inverted, you can use the [w Other Functions] > [Custom
Function] > [Scan Reverse Rec] setting to return the image to the
correct orientation.
• If you are not interested in using the viewfinder along with the LCD
screen, you can set [£ LCD/VF Setup] > [LCD/VF Simul.] to [Off] to conserve the camcorder’s power. Even
when [LCD/VF Simul.] is set to [Off], closing the LCD panel will automatically activate the viewfinder.
Adjusting the Viewfinder/LCD Screen
You can adjust the brightness, contrast, color, sharpness, and backlight
of the viewfinder and LCD screen independently of each other. These
adjustments will not affect your recordings.
Operating modes:
C
Y
P
O
1 Open the setup menu for the viewfinder or LCD screen.
[£ LCD/VF Setup] > [LCD Setup] or [VF Setup]
2 Select [Brightness], [Contrast], [Color], [Sharpness] or [Backlight]
and then press the joystick.
[£ LCD/VF Setup]
[LCD Setup]
[VF Setup]
[Brightness: ±0]
[Contrast: ±0]
[Color: ±0]
[Sharpness: 2]
[Backlight: Normal]
3 Adjust the setting and then press the joystick.
• Repeat steps 2 and 3 to adjust other settings as necessary.
NOTES
• If you set an assignable button to [LCD Setup] or [VF Setup] (A 85), you can press the button to open the
respective submenu.
Setting the Screen to Black & White
The viewfinder and LCD screen display in color by default but you can set
them to black & white. Even when the screen is black & white, onscreen
text and icons will still be displayed in color.
1 Open the [LCD/VF B&W] submenu.
[£ LCD/VF Setup] > [LCD/VF B&W]
[£ LCD/VF Setup]
[LCD/VF B&W]
[Off]
2 Select [On] and then press the joystick.
NOTES
• If you set an assignable button to [LCD/VF B&W] (A 85), you can press the button to turn the black & white
display on and off.
Preparing the Camcorder
• About the LCD and viewfinder screens: The screens are produced using extremely high-precision
manufacturing techniques, with more than 99.99% of the pixels operating to specification. Less than 0.01% of
the pixels may occasionally misfire or appear as black, red, blue or green dots. This has no effect on the
recorded image and does not constitute a malfunction.
34
Using a Tripod
5.5 mm
The camcorder is shipped with the TB-1 Tripod Base for tripods with 0.95 cm (3/8 in.)
screws. You can mount the camcorder on a tripod but do not use tripods with mounting
screws longer than 5.5 mm (0.2 in.) as this may cause damage to the camcorder.
Using a Tripod with 0.64 cm (1/4 in.) Mounting
Screws
To use a tripod with 0.64 cm (1/4 in.) mounting screws, first
attach the supplied tripod adapter base to the camcorder and
then attach the tripod to the adapter base.
1 Remove the original TB-1 Tripod Base from the camcorder.
• Remove the 4 screws and then remove the base.
2 Attach the supplied tripod adapter base for 0.64 cm (1/4 in.)
tripods.
• Firmly screw in the 4 screws.
3 Attach the tripod.
• Firmly screw in the tripod screw.
C
Y
P
O
Removing and Attaching the Grip Unit
The grip unit comes originally attached to the camcorder. You can remove it and replace it with the thumb rest
should the minimal configuration be necessary. However, the joystick (A 27), control dial (A 59) and MAGN.
button/Assignable button 7 (A 85) are not available to operate the camcorder.
Removing the Grip Unit
1 Set the Q switch to OFF.
2 Unscrew the grip unit’s lock screw and gently detach the
grip unit.
• The grip unit contains an internal connection cable so
be sure not to pull it too forcefully.
3 Disconnect the grip unit’s connection plug.
4 Screw the thumb rest onto the camcorder.
Preparing the Camcorder
Attaching the Grip Unit
The grip unit can be attached in any of 24 positions (at 15º
intervals) to give you a convenient grip angle for high- and
low-angle shooting.
35
1 Set the Q switch to OFF.
2 Unscrew the thumb rest and remove it from the
camcorder.
White line
3 Firmly insert the grip unit’s plug all the way into the grip
unit connection terminal on the camcorder.
• Make sure to insert the plug all the way in, until the white
line around the terminal is not visible.
• If the plug is not correctly connected (for example, if the
white line around the terminal is partly visible), all the
controls on the camcorder may be disabled.
4 Attach the grip unit to the camcorder aligning it at the
desired angle and tighten the grip unit’s lock screw.
Adjusting the Grip Belt
Adjust the grip belt so that you can reach the START/STOP button
on the grip unit with your index finger but still have a comfortable
but secure grip.
C
Y
P
O
IMPORTANT
• Be careful not to drop the camcorder when adjusting the grip belt.
Attaching a Shoulder Strap
Pass the ends through the strap mount and adjust the length of
the strap.
IMPORTANT
• Be careful not to drop the camcorder when attaching or adjusting
the shoulder strap.
Preparing the Camcorder
Removing and Attaching the Terminal Covers
You can remove the plastic covers of the following terminals to access them more readily.
36
•
•
•
•
• REMOTE
• DC IN
• USB and HDMI OUT
AV OUT
EXT
MIC
× (headphones)
Removing the Terminal Covers
Open the terminal cover and gently pull it straight out.
Attaching the Terminal Covers
Insert the connecting strip into the opening to attach the terminal cover.
NOTES
• If the connecting strip is difficult to grasp, use a pair of tweezers or similar
tool.
The Camcorder’s Cooling System
C
Y
P
O
The camcorder’s internal temperature is controlled using a cooling fan that
will turn on whenever the camcorder itself is turned on. However, you can
turn off the cooling fan temporarily if necessary.
Operating modes:
[w Other Functions]
[Fan]
[On]
1 Open the [Fan] submenu.
[w Other Functions] > [Fan]
2 Select [Automatic] and then press the joystick.
Options
[On]:
[Automatic]:
The cooling fan is on as long as the camcorder is on.
The cooling fan is temporarily turned off. If the camcorder's internal temperature rises too much,
will appear in yellow on the left of the screen. If the temperature starts to become critical, the
icon
will turn red and the cooling fan will come on to prevent overheating. Once the camcorder has
cooled off sufficiently, the fan will turn off again. While the fan is activated automatically,
will
appear next to the
icon.
Preparing the Camcorder
NOTES
• Depending on the ambient temperature and other shooting conditions, the cooling fan may not turn off even if
you set [Fan] to [Automatic].
• The cooling fan cannot be turned off in
mode.
• When changing the camcorder’s configuration, be careful not to obstruct the cooling fan’s air intake and
exhaust vents (marked respectively as AIR INTAKE and EXHAUST VENT).
• If you set an assignable button to [Fan] (A 85), you can press the button to toggle between the [On] and
[Automatic] settings.
Exhaust vent (EXHAUST VENT)
C
Y
P
O
Intake vent (AIR INTAKE)
37
Using an SD Card
Using an SD Card
SD Cards Compatible for Use with the Camcorder
38
You can use the following types of commercially available Secure Digital (SD) cards with this camcorder. The
camcorder is equipped with two SD card slots. Initialize SD cards (A 40) when you use them with this
camcorder for the first time.
As of October 2012, the video recording function has been tested using SD/SDHC/SDXC cards made by
Panasonic, Toshiba and SanDisk.
Memory card type: . SD card, / SDHC card, 0 SDXC card
SD Speed Class*:
Capacity:
128 MB or larger**.
* When using an SD card without a speed class rating or one rated SD Speed Class 2, you may not be able to record video,
depending on the card used.
**SD cards with a capacity of 64 MB or smaller cannot be used to record video.
NOTES
• About the Speed Class: Speed Class is a standard that indicates the minimum guaranteed data transfer
speed of SD cards. When you buy a new SD card, look for the Speed Class logo on the package.
We recommend using SD cards rated SD Speed Class 4, 6 or 10.
SDXC Cards
You can use SDXC cards with this camcorder. When using SDXC cards with other devices, such as digital
recorders, computers and card readers, make sure that the external device is compatible with SDXC cards.
The table below summarizes compatibility by computer operating system, as of October 2012. For the latest
information, however, contact the computer, operating system or card manufacturer.
Compatible operating systems for SDXC cards
Operating system
Windows 7
C
Y
P
O
Compatibility
Compatible
Windows Vista
Compatible (requires Service Pack 1 or later)
Windows XP
Compatible (requires Service Pack 3 and KB955704 update)
Mac OS X
Compatible (requires version 10.6.5 or later)
IMPORTANT
• If you use an SDXC card with a computer OS that is not SDXC-compatible, you may be prompted to format
the card. In such case, cancel the operation to prevent data loss.
• After repeatedly recording, deleting and editing clips (fragmented memory), it will take longer to write data on
the SD card and recording may stop. Save your recordings and initialize the SD card using the camcorder.
Using an SD Card
Inserting and Removing an SD Card
You can insert an SD card into SD card slot A or slot B. If you have two
SD cards, you can use both slots.
39
1 Turn off the camcorder.
2 Lift the LCD panel upwards and open the SD card compartment
cover.
3 Insert the SD card straight, with the label facing up, all the way
into the SD card slot until it clicks.
4 Close the SD card compartment cover.
• Do not force the cover closed if the SD card is not correctly inserted.
C
Y
P
O
SD card access
indicator
Checking the Status of the SD Card Slots
You can check the status of the SD card slots immediately by looking at
the SD card 2/SD card 3 access indicator. Refer to the following table.
Depending on the position of the LCD panel, it may be difficult to see the
SD card access indicators. In such case, adjust the position or angle of
the LCD panel as necessary.
Access indicator color
SD card slot status
Red
Accessing the SD card.
Green
Recording/playback is possible and the SD card slot is selected
for recording/playback.
Indicator off
An SD card is not inserted, the SD card slot is not currently
selected, or the SD card is not being accessed.
IMPORTANT
• Observe the following precautions while either of the SD card access
indicators is illuminated in red. Failure to do so may result in permanent
data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
• Turn off the camcorder before inserting or removing an SD card. Inserting or removing the SD card with the
camcorder on may result in permanent data loss.
• SD cards have front and back sides that are not interchangeable. Inserting an SD card facing the wrong
direction can cause a malfunction of the camcorder. Be sure to insert the SD card as described in step 3.
Using an SD Card
40
NOTES
• To remove the SD card: Push the SD card once to release it. When the SD card springs out, pull it all the way
out.
• If you set the [w Other Functions] > [Media Access LED] function to [Off], the access indicators will not
illuminate.
Initializing an SD Card
The first time you use an SD card with this camcorder, initialize it first. You can also initialize an SD card to
permanently delete all the data it contains.
When initializing an SD card, you can select quick initialization, which clears the file allocation table but does not
physically erase the stored data, or complete initialization, which deletes all data completely.
Operating modes:
1 Open the [Initialize Media] submenu.
[w Other Functions]
[w Other Functions] > [Initialize Media]
2 Select [*A] or [*B] and then press the joystick.
[Initialize Media]
3 Select [Complete] (complete initialization) or [Quick] (quick
initialization) and then press the joystick.
4 Select [OK] and then press the joystick.
C
Y
P
O
• If you are using the [Complete] initialization option, press the joystick twice to cancel the operation while it is
in progress. You can use the SD card but all data will be erased.
5 When the confirmation message appears, press the joystick.
• The SD card is initialized and all the data it contains is erased.
IMPORTANT
• Initializing an SD card will permanently erase all data, including custom picture files. Lost data cannot be
recovered. Make sure you save important recordings in advance.
• Depending on the SD card, the complete initialization may take up to a few minutes.
NOTES
• If you set an assignable button to [Initialize Media] (A 85), you can press the button to open the initialization
submenu.
Using an SD Card
Switching Between the SD Card Slots
The camcorder features two SD card slots, SD card slot A and SD card
slot B. If both slots contain an SD card, you can switch between them as
necessary.
41
Operating modes:
Press the SLOT SELECT button.
• The access indicator of the selected SD card slot will illuminate in green.
On the screen, the SD card selected is indicated with a Ð mark next to
the SD card icon.
NOTES
• You cannot use the SLOT SELECT button to switch between SD card
slots while recording.
• The SD card slot selected for recording will be used to record both clips
and photos.
Selecting the SD Card Recording Method
Y
P
O
The camcorder features two useful SD card recording methods, relay recording and double slot recording.
Relay recording: This allows you to continue recording on another SD card if the SD card you are using becomes
full. Relay recording is available from SD card slot A to SD card slot B, and vice versa.
C
Double slot recording: This records the same clip simultaneously to both SD cards, which is a convenient way to
make a backup copy of your recording while you record.
Operating modes:
To use relay recording
[w Other Functions]
By default, this function is activated. If it has been deactivated, follow the
procedure below to activate it.
1 Open the [Relay Rec] submenu.
[w Other Functions] > [Relay Rec]
[Relay Rec]
[On]
2 Select [On] and then press the joystick.
To use double slot recording
1 Open the [Double Slot Rec] submenu.
[w Other Functions] > [Double Slot Rec]
[w Other Functions]
[Double Slot Rec]
2 Select [On] and then press the joystick.
[Off]
NOTES
• During relay recording, there will be a very brief stop at the point where
the recording switches to the other SD card. With the supplied software, Data Import Utility, you can join
relay clips recorded on two SD cards and save them on a computer (A 117).
• If an SD card becomes full during double slot recording, recording on both SD cards will stop. On the other
hand, if an error occurs with one of the SD cards, recording will continue on the other SD card.
• Double slot recording cannot be used with relay recording, pre-recording or deleting the last clip recorded.
Using an SD Card
Checking the Available Recording Time
42
When the camcorder is in
mode, the display on the upper left of the screen indicates which SD card slot
is in use and the available recording time (in minutes*) that remains on each SD card.
On the [Media] status screen (A 137), you can check the total space, SD speed class, used space, available
recording time and available number of photos on each of the SD cards.
* The approximate available recording time is based on the current bit rate (A 50).
Recovering Data on an SD Card
Some actions, such as suddenly turning off the camcorder or removing the SD card while data is being
recorded, can cause data errors on the SD card. In such case, you may be able to recover the data on the SD
card.
Operating modes:
1 Insert the SD card with the data to be recovered into the camcorder.
2 When the screen prompts you to recover the data, select [OK] and then press the joystick.
3 When the confirmation message appears, press the joystick.
NOTES
• In some cases, data may not be recovered, such as when the file system is corrupted or the SD card is
physically damaged.
C
Y
P
O
Adjusting the Black Balance
Adjusting the Black Balance
You can have the camcorder adjust the black balance automatically when ambient temperature changes
considerably or if there is a noticeable change in a true black video signal.
43
Operating modes:
1 Open the [ABB] screen.
[~ Camera Setup]
[~ Camera Setup] > [ABB]
[ABB]
2 Attach the body cap to the lens mount.
• If a lens was attached, remove the lens and replace the body cap.
3 Select [OK] and then press the joystick.
• The automatic black balance procedure will start.
4 When the confirmation message appears, press the joystick.
• If the body cap is not correctly attached, [Error] will appear on the screen. Press the joystick and repeat the
procedure from the beginning.
NOTES
• Adjusting the black balance may be necessary in the following cases:
- When using the camcorder for the very first time or after a long period of not using it.
- After sudden or extreme changes in ambient temperature.
- After changing the ISO speed/gain settings.
• The automatic black balance procedure will take approximately 40 seconds when the frame rate is set to 24P.
• During the adjustment of the black balance, you may notice some irregular displays appear on the screen. This
is not a malfunction.
• Resetting the camcorder’s settings using the [w Other Functions] > [Reset] > [All Settings] or [Camera
Settings] menu option will reset also the black balance adjustment. In such case, perform the procedure again.
C
Y
P
O
Adjusting the Black Balance
44
C
Y
P
O
3
Recording
45
Recording Video
This section explains the recording basics. Before you begin recording, make a test recording first to check if the
camcorder operates correctly. Record for approximately 15 minutes at the default bit rate, 24 Mbps (LPCM)
(A 50). Should the camcorder fail to operate correctly, refer to Troubleshooting (A 142).
For details on recording audio, refer to Recording Audio (A 73).
Operating modes:
Preparing to Record
1 Attach the handle unit, grip unit, etc. as necessary to build the desired
configuration (A 29).
2 Attach a charged battery pack to the camcorder (A 22).
3 Insert an SD card into an SD card slot (A 39).
Y
P
O
• Insert another SD card into the other SD card slot to use relay recording
(A 41) or double slot recording (A 41).
4 Attach a lens (A 29).
5 Adjust the viewfinder.
C
Recording
Rear tally lamp
1 Set the Q switch to CAMERA (A 24).
• The camcorder turns on in
mode and enters record pause
mode.
• At first, both SD card access indicators will illuminate in red. After a
moment, the access indicator of the SD card slot selected for
recording will turn green and the other access indicator will go out.
Access indicators
Recording Video
2 Press the START/STOP button to begin recording.
46
• Recording starts. The rear and front tally lamps illuminate and the
recording indicator [ÜREC] appears at the top of the screen.
• You can use the START/STOP button on the grip unit, the
camcorder's body (on the front, next to the lens mount) or the
handle unit.
3 Press the START/STOP button to pause the recording.
• The clip* is recorded to the SD card and the camcorder enters
record pause mode. Both tally lamps will go out.
Front tally
lamp
* “Clip” refers to one movie unit from the point you press the START/STOP button to
start recording until you press again to pause the recording.
IMPORTANT
• Observe the following precautions while either of the SD card access
indicators is illuminated in red. Failure to do so may result in
permanent data loss.
- Do not open the SD card compartment cover and do not remove
the SD cards.
- Do not disconnect the power source or turn off the camcorder.
• Be sure to save your recordings regularly (A 117), especially after making important recordings. Canon shall
not be liable for any loss or corruption of data.
Y
P
O
NOTES
• Depending on the shooting conditions, the camcorder may pick up and record the operation sounds of the
lens (autofocus, aperture, image stabilization, etc.) or the cooling fan. In such case, using an external
microphone is recommended to reduce the effect.
• A single clip can be recorded continuously for up to 12 hours. After 12 hours, the camcorder will automatically
stop recording.
• You can use [w Other Functions] > [Rec Review] (A 82) to review part or all of the last clip recorded.
• You can use [w Other Functions] > [Delete Last Clip] (A 134) to delete the last clip recorded. However, you
cannot delete the last clip if double slot recording is on.
• If [w Other Functions] > [HDMI] > [Rec Command] is set to [On] and you use the HDMI OUT terminal to
connect the camcorder to a device compatible with HDMI recording commands, when you start or stop
recording with the camcorder, the other device will also start or stop recording.
• When the camcorder switches form recording on one SD card to another during relay recording, the video will
be recorded as two separate relay clips. With the supplied software, Data Import Utility, you can join relay
clips recorded on two SD cards and save them on a computer (A 117).
• The video (stream) file in a clip will be split approximately every 2 GB for clips with a long recording time.
Even in such case, playback will be continuous. With the supplied software, Data Import Utility, you can join
such split files into a single clip and save them on a computer (A 117).
C
Recording Video
Locking the Controls in Recording Mode
Once in
mode, you can set the Q switch to C (key lock) to
lock all the physical controls (buttons and switches) on the camcorder,
save for the START/STOP button. This is useful in preventing settings
from being changed due to inadvertently pressing one of the buttons.
Return the Q switch to the CAMERA position to reactivate the
controls.
Additionally, the START/STOP button on the handle unit has its own lock
lever to prevent its accidental operation. Turn the lock lever to C position
to lock the START/STOP button*. Return the lock lever to its original
position to enable use of the START/STOP button again.
* You can still use the START/STOP buttons on the camcorder and grip unit.
C
Y
P
O
47
Recording Video
Onscreen Displays
Refer to this section for an explanation of the various screen displays that appear in
mode. You can use
the custom display function (A 98) to turn off individual onscreen displays if they are not required.
48
1213
14
15 16
17
18
19
20
21
22
23
24
25
26
1
2
3
4
5
6
7
8
9
10
11
27
28 29 30 31 32 33 34 35
When displaying the date and time (A 26):
36
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
C
Remaining battery time (A 49)
SD card status/available recording time (A 49)
Remaining recording time for double slot
recording (A 41)
Current focal length of an attached EF lens*
Temperature warning and cooling fan operation
(A 36)
Light metering (A 61)
Focus mode (A 64)
ND filter (A 58)
Custom picture (A 88)
Key lock (A 47)
White balance (A 62)
View assistance (A 97)
Magnification (A 66)
Recording operation (A 49)
One-shot AF's autofocus frame (A 64)
Onscreen displays superimposed on video output
(A 114)
Time code (A 69)
Onscreen displays recorded with the clip (A 98)
Y
P
O
19 Photo recording - available number of photos
(A 119)
20 Bit rate (A 50)
21 LPCM audio recording** (A 73)
22 Frame rate (A 50)
23 HDMI recording command (A 134)
24 User bit (A 72)
25 Audio output channel (A 115)
26 Audio level meter (A 74, 77)
27 Aperture value (A 59)
28 AE shift (A 60)
29 ISO speed/Gain (A 56)
30 Exposure bar (A 60)
31 Shutter speed (A 53)
32 Peaking (A 66)
33 Sensor area correction for EF-S lenses (A 30)
34 Lens error warning (A 145)
35 Audio peak limiter (A 74, 77)
36 Date/time (A 26)
* The displayed value is an estimate.
**Only displayed when [w Other Functions] > [Bit Rate] is set to [24 Mbps LPCM].
NOTES
• You can press the DISP. button to turn onscreen displays on and off.
Recording Video
1 Remaining battery time
• The icon shows a rough estimate of the remaining charge as a percentage of the full charge of the battery
pack. When a battery pack compatible with Intelligent System is used, the remaining recording/playback
time of the battery pack is displayed, in minutes, next to the icon.
• è é ê ë ì (in red).
When ì is displayed, replace the battery pack with a fully charged one.
• Depending on the conditions under which the camcorder and the battery pack are used, the actual
battery charge may not be indicated accurately.
2 SD card status/available recording time
• The following indicates the SD card status.
2/3 Can record on SD card
4/5 No SD card or cannot record on SD card
The SD card selected for recording is indicated with a Ð mark.
14 Recording operation
ÜREC
STBY
ÜPRE REC
PRE REC STBY
Recording
Record pause
Pre-recording (after pressing the START/STOP button)
Pre-recording (before pressing the START/STOP button)
• When double slot recording (A 41) is activated, the 4 icon will appear to the left of the operation indicator.
CINEMA Preset
C
Y
P
O
You can easily set the camcorder to use a number of preset picturerelated settings especially designed with professional cinematography
and motion picture production in mind. When you use the CINEMA preset
settings, the camcorder will use the advanced Canon Log gamma
(A 97) that makes full use of the new image sensor to achieve an
amazing dynamic range. On the other hand, other custom picture settings
will not be available.
[~ Camera Setup]
[/ CINEMA Locked]
[Off]
1 Open the [/ CINEMA Locked] submenu.
[~ Camera Setup] > [/ CINEMA Locked]
2 Select [On] and then press the joystick.
• All picture-related settings will be set according to the CINEMA preset values.
• [/ LOCKED] appears on the left of the screen.
NOTES
• When Canon Log gamma is used, the image displayed on the screen will appear darker than usual. You can
use the view assistance function (A 97) to display an image that approximates the one that would be
obtained using a normal gamma setting.
49
Video Configuration: System Frequency, Bit Rate and Frame Rate
Video Configuration: System Frequency, Bit Rate and Frame Rate
50
Before you record, select the bit rate and frame rate that best match your creative needs. The options available
will depend on the system frequency selected: 59.94 Hz (former NTSC broadcast area) or 50.00 Hz (former PAL
broadcast area). A single SD card can contain only one type of recordings.
Selecting the System Frequency
[w Other Functions]
Operating modes:
[System Frequency]
1 Open the [System Frequency] submenu.
[w Other Functions] > [System Frequency]
[59.94 Hz] or [50.00 Hz]*
2 Select [59.94 Hz] or [50.00 Hz] and then press the joystick.
• The camcorder will reset and restart in the selected mode.
Selecting the Bit Rate
* Depending on the country/region
of purchase.
[w Other Functions]
The bit rate selected determines also the resolution (frame size) and audio
recording mode of the recordings.
[Bit Rate]
Operating modes:
Y
P
O
[24 Mbps LPCM]
1 Open the [Bit Rate] submenu to set the bit rate and resolution.
[w Other Functions] > [Bit Rate]
C
2 Select the desired option and then press the joystick.
• The selected bit rate will appear on the upper right of the screen.
Selecting the Frame Rate
Operating modes:
1 Open the [Frame Rate] submenu to set the frame rate.
[w Other Functions] > [Frame Rate]
2 Select the desired option and then press the joystick.
• The selected frame rate will appear on the upper right of the screen.
[w Other Functions]
[Frame Rate]
[60i] or [50i]*
* Depending on the country/region
of purchase.
NOTES
• A single SD card cannot be used to record clips at different system frequencies (50.00 Hz recordings/59.94 Hz
recordings).
• For details on the signal output from each terminal, refer to Video Output Configuration (A 111).
• Clips recorded using the 24P frame rate cannot be converted to standard definition using the camcorder.
Video Configuration: System Frequency, Bit Rate and Frame Rate
Available bit rate and frame rate settings
[Bit Rate]
setting1
Resolution
Linear PCM, 2ch
1920 x 1080
[17 Mbps]
[7 Mbps]
1
2
3
4
[System Frequency]
set to [59.94 Hz]
[System Frequency]
set to [50.00 Hz]
Available [Frame Rate] settings
[24 Mbps LPCM]
[24 Mbps]
Audio recording mode
Dolby Digital, 2ch
1440 x 1080
The camcorder uses a variable bit rate (VBR).
Shooting at 30 frames per second, progressive; recorded as 60i.
Shooting at 24 frames per second, progressive; recorded as 60i.
Shooting at 25 frames per second, progressive; recorded as 50i.
C
Y
P
O
[60i]
[PF30]2
[PF24]3
[24P]
[50i]
[PF25]4
51
Changing Main Camera Functions with the Joystick
Changing Main Camera Functions with the Joystick
52
You can adjust three main camera functions –shutter speed, white balance and ISO speed/gain– using only the
joystick. This section will explain the basic operation for changing a value. For specific details about the functions
please refer to the each function’s section: shutter speed (A 53), white balance (A 62), ISO speed/gain
(A 56).
Operating modes:
1 Press the joystick.
White balance (highlighted in orange)
• The white balance mode icon will be highlighted in orange. If no
operation is performed for more than 6 seconds, the display will
return to normal.
• Push the joystick left/right to move the highlight between the
white balance mode icon, the ISO/gain value and the shutter
value.
2 Push the joystick up/down to select the desired value (ISO
speed, gain, shutter) or desired white balance mode and then
press the joystick.
• The selected value will be set and the display will return to
normal.
C
Y
P
O
Push the joystick (ÏÐ) to highlight the ISO/
Gain value or the Shutter value
Shutter Speed
Shutter Speed
Set the shutter speed based on the recording conditions. For example, you may want to set slower shutter
speeds in darker environments. The camcorder offers the following 5 modes.
53
Operating modes:
[Speed]: Allows you to set the shutter speed (in fractions of a second). You can select the increment to use when
adjusting the shutter speed between 1/3-stop and 1/4-stop increments.
[Angle]: You can set the shutter angle to determine the shutter speed.
[Clear Scan]: Set the frequency in order to record CRT computer monitors without displaying black bands or
flicker on the screen.
[Slow]: You can set slower shutter speeds to obtain brighter recordings in places with insufficient lighting.
[Off]: The camcorder uses a standard shutter speed based on the frame rate.
Available Shutter Speeds
Y
P
O
The available shutter speeds vary depending on the frame rate.
Frame rate (59.94 Hz recordings)
PF30
Off
1/60
1/30
Speed
1/3-stop
1/60, 1/80, 1/100, 1/125, 1/160, 1/200, 1/30, 1/40, 1/50, 1/60, 1/80, 1/100,
increments 1/250, 1/320, 1/400, 1/500, 1/640,
1/125, 1/160, 1/200, 1/250, 1/320,
1/800, 1/1000, 1/1250, 1/1600, 1/2000 1/400, 1/500, 1/640, 1/800, 1/1000,
1/1250, 1/1600, 1/2000
1/4-stop
1/60, 1/75, 1/90, 1/100, 1/120, 1/150, 1/30, 1/34, 1/40, 1/48, 1/60, 1/75, 1/90,
increments 1/180, 1/210, 1/250, 1/300, 1/360,
1/100, 1/120, 1/150, 1/180, 1/210, 1/250,
1/420, 1/500, 1/600, 1/720, 1/840,
1/300, 1/360, 1/420, 1/500, 1/600, 1/720,
1/1000, 1/1200, 1/1400, 1/1700,
1/840, 1/1000, 1/1200, 1/1400, 1/1700,
1/2000
1/2000
Angle
360°, 240°, 216°, 180°, 120°, 90°, 360°, 240°, 216°, 180°, 120°, 108°,
60°, 45°, 30°, 22.5°, 15°, 11.25°
90°, 60°, 45°, 30°, 22.5°, 15°,
11.25°
Clear Scan
59.94 Hz to 250.27 Hz
29.97Hz to 250.27 Hz
Slow
1/4, 1/8, 1/15, 1/30
1/4, 1/8, 1/15
Shutter mode
Shutter mode
Off
Speed
C
60i
PF24 / 24P
1/24
1/25, 1/30, 1/40, 1/50, 1/60, 1/80,
1/100, 1/125, 1/160, 1/200, 1/250,
1/320, 1/400, 1/500, 1/640, 1/800,
1/1000, 1/1250, 1/1600, 1/2000
1/24, 1/30, 1/34, 1/40, 1/48, 1/60, 1/75,
1/90, 1/100, 1/120, 1/150, 1/180, 1/210,
1/250, 1/300, 1/360, 1/420, 1/500, 1/600,
1/720,1/840, 1/1000, 1/1200, 1/1400,
1/1700, 1/2000
360°, 345.6°, 288°, 240°, 180°,
172.8°, 144°, 120°, 90°, 86.4°, 72°,
60°, 45°, 30°, 22.5°, 15°, 11.25°
23.98 Hz to 250.27 Hz
1/3, 1/6, 1/12
Frame rate (50.00 Hz recordings)
50i
1/50
1/3-stop
1/50, 1/60, 1/80, 1/100, 1/125, 1/160, 1/200, 1/250, 1/320,
increments 1/400, 1/500, 1/640, 1/800, 1/1000, 1/1250, 1/1600,
1/2000
1/4-stop
1/50, 1/60, 1/75, 1/90, 1/100, 1/120, 1/150, 1/180, 1/210,
increments 1/250, 1/300, 1/350, 1/400, 1/500, 1/600, 1/700, 1/800,
1/1000, 1/1200, 1/1400, 1/1600, 1/2000
Angle
360°, 300°, 240°, 180°, 150°, 120°, 90°, 60°, 45°, 30°,
22.5°, 15°, 11.25°
Clear Scan
50.00 Hz to 250.78 Hz
Slow
1/3, 1/6, 1/12, 1/25
PF25
1/25
1/25, 1/30, 1/40, 1/50, 1/60, 1/80, 1/100, 1/125, 1/160,
1/200, 1/250, 1/320, 1/400, 1/500, 1/640, 1/800, 1/1000,
1/1250, 1/1600, 1/2000
1/25, 1/29, 1/33, 1/40, 1/50, 1/60, 1/75, 1/90, 1/100, 1/120,
1/150, 1/180, 1/210, 1/250, 1/300, 1/350, 1/400, 1/500, 1/600,
1/700, 1/800, 1/1000, 1/1200, 1/1400, 1/1600, 1/2000
360°, 300°, 240°, 180°, 150°, 120°, 90°, 75°, 60°, 45°,
30°, 22.5°, 15°, 11.25°
25.00 Hz to 250.78 Hz
1/3, 1/6, 1/12
Shutter Speed
Changing the Shutter Mode
[~ Camera Setup]
1 Open the shutter [Mode] submenu.
[~ Camera Setup] > [Shutter] > [Mode]
54
[Shutter]
2 Select the desired mode and then press the joystick.
• If you selected [Speed] (the default value), you can continue the
procedure to select the increment scale to use when adjusting the
shutter speed.
[Mode]
[Speed]
3 Open the [Shutter Increment] submenu.
[~ Camera Setup] > [Shutter] > [Shutter Increment]
4 Select [1/3 stop] or [1/4 stop] and then press the joystick.
[~ Camera Setup]
[Shutter]
[Shutter Increment]
[1/4 stop]
Adjusting the Shutter Value
1 Press the SHUTTER button.
Y
P
O
• The current shutter value will be highlighted in orange.
2 Push the joystick up/down to select the desired shutter value
(shutter speed, angle value or clear scan frequency) and then
press the joystick.
C
• The selected shutter value will be set and the display will return to
normal.
• You can also adjust the shutter value using only the joystick (A 52).
NOTES
• If you set an assignable button to [SHUTTER] (A 85), you can press that button instead of the SHUTTER
button to highlight the shutter value.
Using Slow Shutter Mode
When recording in dark surroundings, you can obtain a brighter picture by using slow shutter mode. You can
also use this mode when you wish to add certain effects to your recordings, such as blurring the background
during panning shots or recording a moving subject with an afterimage trail.
• Image quality may not be as good as when using faster shutter speeds in brighter surroundings.
Shutter Speed
NOTES
• Closing down the aperture when recording under bright conditions may cause the picture to appear soft or out
of focus. To avoid the loss of sharpness due to diffraction, use a faster shutter speed, a denser ND filter
(A 58) or open up the aperture.
• When the shutter speed mode is set to [Slow], bright red, green or blue dots may appear on the screen. In
such case, use a faster shutter speed or select a lower ISO speed or gain value (A 56).
• Even when using the [C7: EOS Std.] preset custom picture file, if you set the camcorder to a certain shutter
speed, you may not get the exactly the same image brightness as you would on an EOS digital SLR camera
set to the same shutter speed.
Flicker Reduction
[~ Camera Setup]
You can perform the following procedure to have the camcorder
automatically detect and reduce flicker.
1 Open the [Flicker Reduction] submenu.
[Flicker Reduction]
[Off]
[~ Camera Setup] > [Flicker Reduction]
2 Select [Automatic] and then press the joystick.
Y
P
O
NOTES
• When recording under artificial light sources such as fluorescent, mercury or halogen lamps, the screen may
flicker depending on the shutter speed. To avoid the flicker, set the shutter mode to [Speed] and set the
shutter speed to 1/50* or 1/100 (or an equivalent value in [Angle] mode).
* May not be available depending on the frame rate.
C
55
ISO Speed/Gain
ISO Speed/Gain
Depending on the shooting conditions you may want to adjust the brightness of the image. You can do so by
changing the ISO speed or gain value to adjust the sensitivity of the sensor.
56
Operating modes:
Available ISO speed and gain settings
ISO Speed
Gain
1-stop increments
320*, 400, 800, <850>**, 1600, 3200, 6400, 12800, 20000*
1/3-stop increments
320, 400, 500, 640, 800, <850>**, 1000, 1250, 1600, 2000, 2500, 3200, 4000, 5000, 6400,
8000, 10000, 12800, 16000, 20000
Normal
-6 dB, -3 dB, 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 15 dB, 18 dB, 21 dB, 24 dB, 30 dB
Fine
0 dB to 24 dB in 0.5 dB increments
* The minimum and maximum ISO speeds are available even when the 1-stop increment scale is selected.
**ISO speed required for a suitable dynamic range for Canon Log gamma. Equivalent to a gain value of 2.5 dB.
Changing the ISO Speed or Gain Settings
[~ Camera Setup]
1 Open the ISO Speed/Gain [Select] submenu.
[~ Camera Setup] > [ISO/Gain] > [Select]
Y
P
O
[ISO/Gain]
2 Select [ISO] or [Gain] and then press the joystick.
If you selected [ISO] (the default value):
C
3 Open the [ISO Increment] submenu to select the increment to
use when adjusting the ISO speed.
[Select]
[ISO]
[~ Camera Setup] > [ISO/Gain] > [ISO Increment]
4 Select [1 stop] or [1/3 stop] and then press the joystick.
[~ Camera Setup]
If you selected [Gain]:
3 Open the [Gain] submenu to select the increment to use when
adjusting the gain.
[~ Camera Setup] > [ISO/Gain] > [Gain]
4 Select [Normal] (3-dB increment) or [Fine] (0.5-dB increment) and
then press the joystick.
[ISO/Gain]
[ISO Increment]
[1/3 stop]
[~ Camera Setup]
[ISO/Gain]
[Gain]
[Normal]
ISO Speed/Gain
Adjusting the ISO/Gain Value
1 Press the ISO/GAIN button.
• The current ISO/gain value will be highlighted in orange.
2 Push the joystick up/down to select the desired ISO speed or
gain value and then press the joystick.
• The selected ISO/gain value will be set and the display will return to
normal.
• You can also adjust the ISO/gain value using only the joystick
(A 52).
•
•
•
•
NOTES
When high ISO speeds or gain levels are set, the picture may flicker slightly. ISO 12800 / 30 dB gain and higher
values in particular, allow you to shoot video with a higher sensitivity but are more prone to the appearance of noise.
When high ISO speeds or gain levels are set, bright red, green or blue dots may appear on the screen. In such
case, use a faster shutter speed (A 53) or select a lower ISO speed or gain value.
When the ISO speed or gain level is changed, some noise may appear momentarily on the screen. Do not
adjust the ISO speed/gain level while recording.
If you set an assignable button to [ISO/GAIN] (A 85), you can press that button instead of the ISO/GAIN
button to highlight the ISO/gain value.
C
Y
P
O
57
ND Filter
ND Filter
58
Using the ND filters allows you keep the aperture within an appropriate
range when recording in bright surroundings*.
* Closing down the aperture when recording under bright conditions may cause the
picture to appear soft or out of focus. To avoid the loss of sharpness due to diffraction,
use a denser ND filter or a faster shutter speed (A 53).
Operating modes:
Turn the ND FILTER dial toward the + or - direction to select the
desired ND filter setting.
• Turning the dial up (in the + direction) will change the ND filter setting in
the following order: [ND1 2 stops] [ND2 4 stops] [ND3 6 stops] ND filter off. (Turning the dial down (in the - direction) will cycle through
the settings in reverse order.)
NOTES
• Depending on the scene, the color may change when turning the ND filter on/off. Setting a custom white
balance (A 62) may be effective in such case.
C
Y
P
O
Adjusting the Aperture
Adjusting the Aperture
You can affect the brightness of your recordings or change the depth of field by adjusting the aperture. For
example, use a small aperture value for a shallow depth of field that isolates the subject in focus and nicely blurs
the background.
Operating modes:
Manual Aperture Control
You can adjust the aperture value of most EF lenses using the control
dial on the grip unit. Available aperture values will vary depending on
the EF lens attached to the camcorder.
Control dial
Y
P
O
Selecting the Increment Scale to Use When Adjusting the
Aperture
C
1 Open the [Iris Increment] submenu.
[~ Camera Setup] > [Iris] > [Iris Increment]
2 Select [1/2 stop], [1/3 stop] or [Fine] and then press the joystick.
Changing the Aperture Value
[~ Camera Setup]
[Iris]
[Iris Increment]
[1/3 stop]
Turn the control dial to adjust the aperture.
• The selected aperture value will appear on the lower left of the screen.
• When [~ Camera Setup] > [Iris] > [Iris Increment] is set to [Fine], the actual increments will be smaller than
1/3 stop but the onscreen display will show the closest 1/3-stop aperture value.
NOTES
• When using an EF lens with no lens contacts, such as a Canon EF Cinema lens, you cannot adjust the
aperture using the camcorder. Adjust the aperture using the lens.
• You can use the [w Other Functions] > [Custom Function] > [Grip Ctrl Dial Dir.] setting (A 98) to change
the direction of the adjustment when you turn the control dial.
• If you are using an EF lens that can correct the aperture value according to the position of the zoom, you can
use the [~ Camera Setup] > [Iris] > [Zoom-Iris Correct.] setting to select whether to maintain the f/stop as
you zoom.
• If you set an assignable button to [Iris +] or [Iris -] (A 85), you can press the button to respectively open up or
close the aperture.
59
Adjusting the Aperture
Momentary Automatic Aperture - Push Auto Iris
Press the PUSH AUTO IRIS button to have the camcorder automatically adjust
the aperture (f/stop) for an optimal exposure.
60
Hold down the PUSH AUTO IRIS button.
• The camcorder will automatically adjust the aperture to obtain optimal
exposure. As long as you hold the button pressed down, m will appear on
the screen next to the aperture value.
• When you release the button, the selected f/stop will be set as the aperture
value. Automatic aperture mode will end and the m icon next to the aperture
value will disappear.
Exposure Compensation - AE Shift
Use AE shift to compensate the automatic exposure set by the camcorder
using the push auto iris function in order to darken or lighten the image. You
can select from 15 available AE shift levels.
1 Open the [AE Shift] submenu.
[~ Camera Setup]
[~ Camera Setup] > [AE Shift]
2 Select an AE shift level and then press the joystick.
Available AE Shift Levels
+2.0
+1.5
+1.25
+1.0
+0.75
+0.5
+0.25
-0.25
-0.5
-0.75
-1.0
-1.25
-1.5
-2.0
±0
C
Y
P
O
[AE Shift]
[±0]
NOTES
• Alternatively, you can set the AE shift level by turning the control dial while holding the PUSH AUTO IRIS button
pressed down.
• If you set an assignable button to [AE Shift +] or [AE Shift -] (A 85), you can press the button to adjust the AE
shift level.
• When you use the auto push iris function after setting an AE shift level, the camcorder will try to adjust the
aperture (f/stop) so as to achieve the AE shift level that was set rather than optimal aperture.
The Exposure Bar
You can use the exposure bar as a reference when adjusting the aperture or
shutter speed or when compensating the exposure using AE shift. The Î on
top of the exposure bar indicates optimal exposure without any shift (AE±0); the
scale markings indicate the deviation from optimal exposure in 1/2 EV
increments. The indicator inside the exposure bar represents the current
exposure. When the difference between current and optimal exposure is larger
than ±2 EV, the indicator will flash at the edge of the exposure bar. Optimal
exposure will change depending on the light metering mode (A 61) used.
Optimal exposure AE±0
Current exposure
Adjusting the Aperture
Light Metering Mode
Select the light metering mode to match the recording conditions. Using the appropriate setting will ensure that
the camcorder obtains the most suitable exposure level when the push auto iris function is used.
1 Open the [Light Metering] submenu.
[~ Camera Setup]
[~ Camera Setup] > [Light Metering]
2 Select the desired option and then press the joystick.
[Light Metering]
• The icon of the selected mode appears on the left of the screen.
Options
[Backlight] °:
[Standard]:
[Spotlight] ®:
[Standard]
Suitable when recording backlit scenes.
Averages the light metered from the entire screen, giving more weight to the subject in the center.
Use this option when recording a scene in which only a certain part of the picture is lit, for example,
when the subject is lit by a spotlight.
NOTES
• If you set an assignable button to [Backlight] or [Spotlight] (A 85), you can press the button to change the
light metering mode.
C
Y
P
O
61
White Balance
White Balance
The camcorder uses an electronic white balance process to calibrate the picture and ensure accurate colors
under different lighting conditions. There are 4 methods of setting the white balance.
62
Custom white balance: You can use a white object to establish the white balance and set it to one of two custom
white balance positions, ÅA or ÅB.
Preset white balance: Set the white balance to ¼ (daylight, 5,400 K) or
(incandescent lamp, 3,200 K). Preset
white balance settings can be further fine-tuned within a range of -9 to 9.
Set color temperature: Allows you to set the color temperature between 2,000 K and 15,000 K.
Auto white balance: The camcorder automatically adjusts the white balance to the optimal level.
Operating modes:
NOTES
• The [Color Matrix] (A 94) and [White Balance] (A 95, 96) custom picture settings take precedence over the
white balance settings.
• You can use the [w Other Functions] > [Custom Function] > [Shockless WB] setting (A 98) to make the
transition look smoother when you change the white balance settings.
Custom White Balance
1 Press the WB button.
C
Y
P
O
• The white balance mode icon will be highlighted in orange.
• You can also select the white balance mode icon using only the
joystick (A 52).
2 Push the joystick up/down to select the ÅA or ÅB icon.
• If a custom white balance has been stored previously, press the
joystick to set the stored custom white balance. You do not need to
perform the rest of the procedure.
• If a custom white balance has not yet been stored, the custom white
balance icon ÅA or ÅB and default value (5,500 K) will flash slowly.
Continue the procedure to establish the custom white balance.
3 Point the camcorder at a white object so that it fills the whole
screen.
• Use the same lighting conditions you plan to use when recording.
4 Press the Å button.
• The Å A or Å B icon will flash quickly.
• Make sure the white object fills the screen until the procedure is completed.
• After the icon stops flashing, the procedure is completed. The setting is retained even if you turn off the
camcorder.
NOTES
• Readjust the custom white balance if the light source or ND filter setting changes.
• Very rarely and depending on the light source, Å may keep flashing (it will change to a slow flashing). The
result will still be better than with the auto white balance.
White Balance
Preset White Balance Settings
1 Press the WB button.
• The white balance mode icon will be highlighted in orange.
• You can also select the white balance mode icon using only the joystick (A 52).
2 Push the joystick up/down to select the ¼ or É icon and then press the joystick.
• If necessary, instead of pressing the joystick, you can continue the procedure to fine-tune the preset settings
within a range of -9 to 9.
3 Press the Å button.
• The adjustment value ±0 will appear next to the white balance icon, highlighted in orange.
4 Push the joystick up/down to change the adjustment value and then press the joystick.
• The selected adjustment value will be set and will appear next to the white balance icon.
Color Temperature Setting
1 Press the WB button.
• The white balance mode icon will be highlighted in orange.
• You can also select the white balance mode icon using only the joystick (A 52).
2 Push the joystick up/down to select the È icon.
3 Press the Å button.
Y
P
O
• The default color temperature value (5,500 K) will be highlighted in orange.
C
4 Push the joystick up/down to change the color temperature value and then press the joystick.
• The selected color temperature will be set and will appear next to the white balance icon.
Auto White Balance
The camcorder constantly adjusts the white balance automatically to achieve an optimal level. The camcorder
will adjust the white balance if the light source changes.
1 Press the WB button.
• The white balance mode icon will be highlighted in orange.
• You can also select the white balance mode icon using only the joystick (A 52).
2 Push the joystick up/down to select the m icon and then press the joystick.
• The m icon appears next to the color temperature display.
NOTES
• Custom white balance may provide better results in the following cases:
- Changing lighting conditions
- Close-ups
- Subjects in a single color (sky, sea or forest)
- Under mercury lamps and certain types of fluorescent and LED lights
63
Adjusting the Focus
Adjusting the Focus
The camcorder offers two ways to focus.
64
Manual focus: Turn the focus ring on the attached lens to adjust the focus. The camcorder offers several focus
assistance functions to help you focus more accurately when using the manual focus.
One-shot AF: With the lens's focus mode switch set to AF, press and hold the ONE-SHOT AF button to let the
camcorder focus automatically on the subject at the center of the screen.
Operating modes:
Manual Focus
Turn the focus ring to adjust the focus.
NOTES
• In most cases, you can use the focus ring on the lens to adjust the focus even when the focus mode switch is
set to AF (autofocus). However, depending on the lens, the focus ring may be disabled in AF mode. In such
case, set the focus mode switch to MF.
• If you operate the zoom after focusing manually, the focus on the subject may be lost.
• When adjusting the focus, be careful not to touch the front of the lens or moving parts on the lens except for
the focus ring.
• If you focus manually and then leave the camcorder with the power turned on, the focus on the subject may
be lost after a while. This possible slight shift in focus is a result of the internal temperature rising in the
camcorder and lens. Check the focus before resuming shooting.
C
Y
P
O
One-Shot AF
1 Set the focus mode switch on the lens to AF in advance.
• Refer to the instruction manual of the lens used.
• [AF] will appear on the left of the screen.
2 Press and hold the ONE-SHOT AF button.
• The AF frame will appear at the center of the screen and the
camcorder will focus automatically. When correct focus has been
achieved, the AF frame turns green.
• If the camcorder cannot focus automatically, the AF frame will turn
red.
• The AF frame will disappear when you release the ONE-SHOT AF
button.
NOTES
• One-shot AF is not available when the shutter mode is set to [Slow] and the shutter speed is set to 1/4 or 1/3.
• When the One-shot AF function is used with the frame rate set to PF30, PF24 or 24P (59.94 Hz recordings) or PF25
(50.00 Hz recordings), the camcorder will take longer to focus automatically.
• The point where the camcorder focuses may change slightly depending on shooting conditions, such as subject,
brightness and zoom position. Check the focus before resuming shooting.
• One-shot AF is only available when using EF lenses equipped with autofocus (AF) function. Refer to the
instruction manual of the lens used.
Adjusting the Focus
• With some EF lenses, the camcorder may take longer to focus automatically or may not be able to focus
correctly. Visit your local Canon Web site for the latest information.
• One-shot AF may not work well on the following subjects or in the following cases. In such case, focus
manually.
- Reflective surfaces
- Subjects with low contrast or without vertical lines
- Fast moving subjects
- Through dirty or wet windows
- Night scenes
C
Y
P
O
65
Adjusting the Focus
Using the Focus Assistance Functions
66
In order to focus more accurately, you can use two focus assistance functions – peaking, which creates a clearer
contrast by emphasizing the outlines of the subject, and magnification, which enlarges the image on the screen.
You can use both functions simultaneously for greater effect.
You can also use the [w Other Functions] > [Custom Function] > [F. Assist. B&W] setting (A 98) to switch
the screen to black & white while using the focus assistance functions.
Peaking
[£ LCD/VF Setup]
The camcorder offers two peaking levels. Select the level before activating
peaking.
1 Open the [Select] submenu (under [Peaking]) to select the peaking level.
[£ LCD/VF Setup] > [Select] (under [Peaking])
[Select]
(under [Peaking])
[Peaking 1]
2 Select the desired level and then press the joystick.
3 Press the PEAKING button.
• The peaking icon (J or K) appears at the lower center of the
screen and the outlines in the image will be emphasized.
• Press the button again to turn off peaking.
• Alternatively, you can use the [£ LCD/VF Setup] > [Peaking]
setting to turn peaking on and off.
Magnification
Y
P
O
Press the MAGN. button.
• ^ appears at the lower center of the screen and the center of the
screen is magnified approximately 2 times*.
• Press the button again to cancel the magnification.
C
* The magnification that appears on the LCD screen and on the viewfinder screen is
different. The magnification also differs based on the video configuration.
•
•
•
•
•
NOTES
Peaking/Magnification appears only on the camcorder screen. It will not
appear on an external monitor connected to the camcorder and will not
affect your recordings.
You can use the [£ LCD/VF Setup] > [Peaking 1] and [Peaking 2]
settings to set the color, gain and frequency of the two peaking levels
independently of each other.
The camcorder features professional video scopes (A 80). You can
display the edge monitor to help you focus even more accurately.
You can use peaking together with the edge monitor. In such case, The gain and frequency of the peaking
effect will be adjusted automatically according to the gain settings of the edge monitor.
You can use the [w Other Functions] > [Custom Function] > [Magn. Add. Disp.] setting (A 98) to select an
additional assistance display (peaking or the edge monitor) to also be displayed when magnification is used.
Onscreen Markers and Zebra Patterns
Onscreen Markers and Zebra Patterns
Using onscreen markers allows you to make sure your subject is correctly framed and is within the appropriate
safe area. The zebra patterns help you identify areas that are overexposed. The onscreen markers and zebra
pattern will not affect your recordings.
Operating modes:
Displaying Onscreen Markers
[£ LCD/VF Setup]
The camcorder offers 5 types of onscreen markers. You can display
multiple onscreen markers simultaneously.
[Markers]
1 Open the [Markers] submenu.
[£ LCD/VF Setup] > [Markers]
[Center]
[Horizontal]
[Grid]
2 Select a marker you wish to display, select [White] or [Gray] and
then press the joystick.
[Safety Zone]
[Aspect Marker]
• Select [Off] to turn off the selected marker.
• You can display multiple markers simultaneously. Repeat this step as
necessary.
• If you selected [Safety Zone] or [Aspect Marker], continue to step 3.
Otherwise, you can skip to step 4.
[Off]
Y
P
O
3 Select [Safety Zone Area] or [Aspect Ratio], select the desired option and then press the joystick.
C
4 Select [Enable], select [On] and then press the joystick to enable the onscreen markers.
• All of the selected onscreen markers will be displayed.
• Select [Off] to turn off all onscreen markers.
Options
[Center]:
[Horizontal]:
[Grid]:
[Safety Zone]:
Displays a small marker that indicates the center of the screen.
Displays a horizontal line to help you compose level shots.
Displays a grid that allows you to frame your shots correctly (horizontally and vertically).
Displays indicators that show various safe areas, such as the action safe area and text safe area.
Available options for [Safety Zone Area] are [80%], [90%], [92.5%] and [95%].
[Aspect Marker]: Displays markers that indicate various aspect ratios to help you keep your shot within that area.
Available options for [Aspect Ratio] are [4:3], [13:9], [14:9], [1.66:1], [1.75:1], [1.85:1] and [2.35:1].
Safety zone 80%
Level marker
Aspect guide 4:3
67
Onscreen Markers and Zebra Patterns
Grid
68
Center marker
NOTES
• If you set an assignable button to [Markers] (A 85), you can press the button to turn the onscreen markers on
and off.
Displaying Zebra Patterns
The camcorder has a zebra pattern feature that shows black and white
diagonal stripes over areas that are overexposed. This is displayed only
on the screen and will not affect your recordings. There are two types of
zebra patterns and you can display both simultaneously. Zebra 1 lets you
identify areas within a certain range (±5% of a specified level) while zebra
2 lets you identify areas that are over a specified level. When you display
both simultaneously and they overlap, only zebra 1 will be displayed in
those areas.
1 Open the zebra pattern [Select] submenu.
[£ LCD/VF Setup] > [Select] (under [Zebra])
C
Y
P
O
[£ LCD/VF Setup]
[Select]
(under [Zebra])
[Zebra 1]
2 Select [Zebra 1], [Zebra 2] or [Zebra 1&2] and then press the
joystick.
3 Open the zebra level submenu.
[£ LCD/VF Setup] > [Zebra 1 Level] or [Zebra 2 Level]
4 Select a zebra level and then press the joystick.
5 Press the ZEBRA button to activate the selected zebra pattern.
• Alternatively, before closing the menu, you can also select [Zebra],
select [On] and then press the joystick.
NOTES
• You can use the [£ LCD/VF Setup] > [Zebra HD Output] setting to display the zebra pattern on an external
monitor connected to the HDMI OUT terminal (HD output only).
Setting the Time Code
Setting the Time Code
The camcorder generates a time code signal and embeds it in your recordings. You can output the time code
along with video output from the HDMI OUT terminal (A 134). For 59.94 Hz recordings, you can also select
between a drop frame and non-drop frame time code.
Operating modes:
Selecting the Running Mode
You can select the running mode of the camcorder’s time code.
[¤ TC/UB Setup]
[Time Code]
1 Open the time code [Mode] submenu.
[¤ TC/UB Setup] > [Time Code] > [Mode]
2 Select the desired option and then press the joystick.
• If you selected [Regen.], you do not need to perform the rest of this
procedure. If you selected [Preset] and would like to set the time
code’s initial value, see the following section Setting the Time Code’s
Initial Value.
3 After you select [Preset], open the time code [Run] submenu.
[¤ TC/UB Setup] > [Time Code] > [Run]
Y
P
O
[Mode]
[Preset]
[¤ TC/UB Setup]
[Time Code]
4 Select the desired option and then press the joystick.
Options
[Preset]:
C
The time code starts from an initial value you can select in
advance. The default initial time code is 00:00:00.00. The time
code’s running mode depends on the [Run] setting.
[Rec Run]: The time code runs only while recording so clips
recorded consecutively on the same SD card will have
continuous time codes.
[Free Run]: The time code starts running the moment you press
the joystick to select this option and keeps running
regardless of the camcorder’s operation.
[Regen.]: The camcorder will read the selected SD card and the time code
will continue from the last recorded time code on the SD card.
The time code runs only while recording so clips recorded
consecutively on the same SD card will have continuous time
codes.
[Run]
[Rec Run]
Setting the Time Code’s Initial Value
If you set the time code mode to [Preset], you can set the initial value of
the time code.
1 Open the time code [Setting] submenu.
[¤ TC/UB Setup] > [Time Code] > [Setting]
[¤ TC/UB Setup]
[Time Code]
[Setting]
69
Setting the Time Code
70
2 Select [Set] and then press the joystick.
• The time code setting screen appears with an orange selection frame indicating the hours.
• To reset the time code to [00:00:00.00], select [Reset] instead. If the running mode is set to [Free Run], the
time code will be reset the moment you press the joystick and keep running continuously from 00:00:00.00.
3 Push the joystick up/down to set the hours and then press the joystick to move to the minutes.
4 Change the rest of the fields (minutes, seconds, frame) in the same way.
• Press the CANCEL button to close the screen without setting the time code.
5 Select [Set] and then press the joystick to close the screen.
• If the running mode is set to [Free Run], the time code will start running from the selected time code the
moment you press the joystick.
Selecting Drop or Non-Drop Frame
When [w Other Functions] > [System Frequency] is set to [59.94 Hz],
you can select between a drop frame (DF) or non-drop frame (NDF) time
code, depending on how you plan to use your recordings.
In the following cases, the time code is set to non-drop frame (NDF) and
cannot be changed.
- [w Other Functions] > [System Frequency] is set to [50.00 Hz]
- [w Other Functions] > [System Frequency] is set to [59.94 Hz] and
the frame rate is set to 24P
1 Open the [DF/NDF] submenu.
[¤ TC/UB Setup] > [Time Code] > [DF/NDF]
C
[¤ TC/UB Setup]
[Time Code]
[DF/NDF]
[DF]
Y
P
O
2 Select [DF] or [NDF] and then press the joystick.
• The time code display will differ depending on the setting. When you select [DF], the time code will appear
as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00].
Putting the Time Code Display on Hold
If you set an assignable button to [Time Code Hold] (A 85), you can press the button to freeze the display of
the time code. While the time code display is put on hold, [H] will appear on the screen next to the time code.
The time code continues to run normally while the time code display is on hold. When you resume the time code
display, the current time code will be displayed.
About the Time Code Display
An icon may appear next to the time code depending on the operation. Refer to the following table.
Icon
Description
R
The time code is set to [Regen.].
P
The time code is set to [Preset] and the running mode is set to [Rec Run].
F
The time code is set to [Preset] and the running mode is set to [Free Run].
H
Time code display is on hold.
No icon
Time code during clip playback.
Setting the Time Code
NOTES
• When the frame rate is set to 24P, the frames value in the time code runs from 0 to 23. When the frame rate is
set to 50i or PF25, it runs from 0 to 24. With other frame rates, it runs from 0 to 29.
• When pre-recording mode is activated, [Free Run] is set automatically and cannot be changed.
• When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at
the point where the recording starts.
• As long as the built-in rechargeable lithium battery is charged and you selected the [Free Run] running mode,
the time code continues to run even if you disconnect all other power sources. However, this is less accurate
than when the camcorder is on.
• If you set an assignable button to [Time Code] (A 85), you can press the button to open the [¤ TC/UB
Setup] > [Time Code] submenu.
C
Y
P
O
71
Setting the User Bit
Setting the User Bit
72
The user bit display can be selected from the date or the time of
recording, or an identification code consisting of 8 characters in the
hexadecimal system. There are sixteen possible characters: the numbers
0 to 9 and the letters A to F.
Operating modes:
[¤ TC/UB Setup]
[User Bit]
[Type]
1 Open the user bit [Type] submenu.
[Setting]
[¤ TC/UB Setup] > [User Bit] > [Type]
2 Select the desired user bit type and then press the joystick.
• Select [Setting] to set your own identification code, [Time] to use the time as user bit, or [Date] to use the
date as the user bit.
• If you selected [Time] or [Date], you do not need to perform the rest of the procedure. If you selected
[Setting], continue the procedure to set the identification code.
3 Select [Set] and then press the joystick.
• The user bit setting screen appears with an orange selection frame on the leftmost digit.
• To reset the user bit to [00 00 00 00], select [Reset] instead.
4 Push the joystick up/down to select the first character and then press the joystick to move to the
next digit.
Y
P
O
• Change the rest of the digits in the same way.
• Press the CANCEL button to close the screen without setting the user bit.
C
5 Select [Set] and then press the joystick to close the screen.
NOTES
• User bit output: The user bit will be output along with the video output from the HDMI OUT terminal. In
mode, you can select the output mode with the [¤ TC/UB Setup] > [User Bit] > [Output Mode] setting.
When [Output Mode] is set to [Pulldown] and the frame rate is set to PF24 or 24P, the user bit will be
converted to 60i using the 2:3 pulldown method before it is output.
Recording Audio
Recording Audio
You can record audio using the built-in stereo microphone*, commercially available microphones (XLR terminal*,
MIC terminal) or line input (XLR terminal*). Using the XLR terminals, you can select the audio input independently
for channel 1 and channel 2.
When the bit rate is set to [24 Mbps LPCM], you can enjoy two-channel linear PCM audio recording with a
sampling frequency of 48 kHz. LPCM audio playback is also available for clips recorded with that bit rate.
* Only available when the handle unit is attached to the camcorder.
Operating modes:
Connecting an External Microphone or External Audio Input Source to the Camcorder
In order to use the microphone holder and XLR terminals, the handle unit must be attached to the camcorder.
Follow the procedure below to attach a microphone (refer also to the following illustration). To connect an
external device to the camcorder, plug the device’s cable into the camcorder’s XLR terminal (햵).
1 Loosen the microphone lock screw (햲), open the microphone holder and insert the microphone (햳).
2 Tighten the lock screw and put the microphone cable through the microphone cable clamp under
the microphone holder (햴).
3 Plug the microphone cable into the desired XLR terminal (햵) or the MIC terminal (햶).
C
Y
P
O
XLR terminals
MIC terminal
Microphone lock screw
Cable clamp
Using the Built-in Microphone or an External Microphone
Connected to the MIC Terminal
Follow the step below to use the built-in microphone or an external microphone
attached to the MIC terminal. Use commercially available condenser microphones
with their own power supply and a ∅ 3.5 mm mini-stereo plug*. You can use the
microphone attenuator for either type of microphone. If you are using the built-in
microphone, you can also use the low-cut filter and select the sensitivity.
* For 50.00 Hz recordings, use commercially available microphones with a cable no longer than
3 m.
Set the AUDIO IN switch of the desired channel to INT.
• If you connect a microphone to the MIC terminal while the AUDIO IN switch is
set to INT, the camcorder will switch automatically from the built-in microphone
to the external microphone.
CH1/CH2
AUDIO IN switches
73
Recording Audio
Adjusting the Audio Level for the MIC Terminal
You can adjust the audio recording level of a microphone attached to the MIC terminal to auto or manual. The
way to adjust the audio level depends on whether the handle unit is attached to the camcorder.
74
CH1
When the Handle Unit is Attached
dial
With the handle unit attached, the audio level adjustment is done using the
audio controls on the handle unit.
1 Select the audio level adjustment mode with the CH1 audio level switch.
• Automatic audio level adjustment: Set the CH1 audio level switch to
A. You do not need to perform the rest of the procedure.
Manual audio level adjustment: Set the CH1 audio level switch to M.
Continue the procedure to set the microphone's audio recording level.
CH1
audio level switch
2 Turn the CH1
dial to adjust the audio level.
• For reference, 0 corresponds to -G, 5 corresponds to 0 dB, and 10
corresponds to +18 dB.
• As a guideline, adjust the audio recording level so that the audio level
meter on the screen will go to the right of the 18 dB mark (one mark right
of the 20 dB mark) only occasionally.
• Closing the protective cover will prevent the audio controls from being
changed inadvertently.
When the Handle Unit is Not Attached
Y
P
O
You can use an external microphone connected to the MIC terminal without attaching the handle unit. In such
case, adjust the microphone's audio recording level using the menu.
C
1 Open the [MIC Mode] submenu.
[¡ Audio Setup] > [Audio Input] > [MIC Mode]
2 Select [Automatic] or [Manual] and then press the joystick.
• If you selected [Automatic], you do not need to perform the rest of the
procedure. If you selected [Manual], continue the procedure to set the
microphone’s audio recording level.
3 Open the [MIC Level] screen.
[¡ Audio Setup] > [Audio Input] > [MIC Level]
4 Push the joystick up/down to set the audio recording level and then
press the joystick.
• For reference, 0 corresponds to -G, 50 corresponds to 0 dB, and
99 corresponds to +18 dB.
• As a guideline, adjust the audio recording level so that the audio level
meter on the screen will go to the right of the 18 dB mark (one mark
right of the 20 dB mark) only occasionally.
[¡ Audio Setup]
[Audio Input]
[MIC Mode]
[Automatic]
[¡ Audio Setup]
[Audio Input]
[MIC Level]
[50]
NOTES
• When adjusting the audio level manually, you can activate the audio
peak limiter with the [¡ Audio Setup] > [Audio Input] > [Limiter]
setting. When activated, the audio peak limiter will limit the amplitude of audio input signals when they exceed
-6 dBFS.
• We recommend using headphones when adjusting the audio level. If the input level is too high, audio may
become distorted even if the audio level indicator shows an appropriate level.
• If you set an assignable button to [Audio Level] (A 85), you can press the button to turn the onscreen audio
level indicator on and off.
Recording Audio
Configuring the Built-in Microphone’s Low-Cut Filter
1 Open the [Int. Mic Low Cut] submenu.
[¡ Audio Setup] > [Audio Input] > [Int. Mic Low Cut]
[¡ Audio Setup]
[Audio Input]
2 Select the desired option and then press the joystick.
[Int. Mic Low Cut]
Options
[Off]:
For recording audio under usual conditions.
[LC1]:
[LC2]:
For recording mainly people’s voices.
For reducing the background sound of wind when recording
outdoors in windy surroundings (for example, on a beach or close to
buildings). Note that when you use this setting some low-frequency
sounds may be suppressed along with the sound of wind.
Selecting the Built-in Microphone’s Sensitivity
1 Open the [Int. Mic Sensitivity] submenu.
[¡ Audio Setup] > [Audio Input] > [Int. Mic Sensitivity]
[Off]
[¡ Audio Setup]
[Audio Input]
2 Select the desired option and then press the joystick.
Options
[Normal]:
[High]:
[Int. Mic Sensitivity]
For recording audio under usual conditions.
For recording audio at a higher volume (+6 dB).
Activating the Microphone Attenuator
C
Y
P
O
If the audio level is too high and the sound sounds distorted when
recording with the built-in microphone or an external microphone
connected to the MIC terminal, activate the microphone attenuator (builtin microphone: 12 dB, external microphone (MIC terminal): 20 dB).
1 Open the [MIC/Int. Mic Att.] submenu.
[¡ Audio Setup] > [Audio Input] > [MIC/Int. Mic Att.]
2 Select [On] and then press the joystick.
[Normal]
[¡ Audio Setup]
[Audio Input]
[MIC/Int. Mic Att.]
[Off]
75
Recording Audio
Using Audio Input from the XLR Terminals
Using the XLR terminals CH1 and CH2, you can record audio independently to the two audio channels from a
microphone or analog audio input source.
76
Switching Between Microphone and Line Input
CH1/CH2
1 Set the AUDIO IN switch of the desired channel to EXT.
dials
2 Set the XLR terminal switch of the desired channel to LINE or
MIC.
• To supply a microphone with phantom power, set the switch to
MIC+48V instead. Make sure to connect the microphone first,
before turning the phantom power on. Keep the microphone
connected when turning off the phantom power.
• When using the XLR terminal to record to only one channel, use
the CH1 terminal.
Selecting the Recording Channel
C
Y
P
O
You can select to which channel the camcorder will record audio.
1 Open the [XLR Rec Channel] submenu.
[¡ Audio Setup] > [Audio Input] > [XLR Rec Channel]
2 Select the desired option and then press the joystick.
Options
[CH1]:
[CH1/CH2]:
Records audio to each channel separately. Audio input
into CH1 is recorded to channel 1, while audio input into
CH2 is recorded to channel 2.
Audio input into CH1 is recorded to both channels. Audio
input into CH2 will not be recorded.
CH1/CH2
audio level
switches
XLR terminal
switches
CH1/CH2
AUDIO IN
switches
[¡ Audio Setup]
[Audio Input]
[XLR Rec Channel]
[CH1]
IMPORTANT
• When connecting a microphone or device that does not support phantom power, make sure to set the XLR
terminal switch to MIC or LINE, respectively. If you set the switch to MIC+48V, the microphone or device may
be damaged.
Recording Audio
Adjusting the Audio Level for the XLR Terminals
You can set the audio recording level for audio input from the XLR terminals to automatic or manual
independently for each channel.
CH1/CH2
audio level switches
Automatic Audio Level Adjustment
Set the audio level switch of the desired channel to A (automatic) to let the
camcorder automatically adjust that channel’s audio level.
NOTES
• When both CH1 and CH2 are set to the same audio input (external
microphone or external line input), if the audio level is set to automatic, you
can use the [¡ Audio Setup] > [Audio Input] > [XLR ALC Link] setting to
link the audio level adjustment of both channels.
CH1/CH2
Manual Audio Level Adjustment
dials
You can set the audio level for each channel manually from -G to 18 dB.
Y
P
O
1 Set the audio level switch of the desired channel to M.
2 Turn the corresponding
dial to adjust the audio level.
• For reference, 0 corresponds to -G, 5 corresponds to 0 dB, and 10
corresponds to +18 dB.
• As a guideline, adjust the audio recording level so that the audio level
meter on the screen will go to the right of the 18 dB mark (one mark right
of the 20 dB mark) only occasionally.
• Closing the protective cover will prevent the audio controls from being
changed inadvertently.
C
CH1/CH2
audio level
switches
NOTES
• If at least one of the channels is set to manual audio level adjustment, you
can also activate the audio peak limiter to prevent audio distortions. When
activated, the audio peak limiter will limit the amplitude of audio input
signals when they exceed -6 dBFS. Use the [¡ Audio Setup] > [Audio
Input] > [Limiter] setting.
• We recommend using headphones when adjusting the audio level. If the input level is too high, audio may
become distorted even if the audio level indicator shows an appropriate level.
• If you set an assignable button to [Audio Level] (A 85), you can press the button to turn the onscreen audio
level indicator on and off.
77
Recording Audio
Adjusting the Microphone’s Sensitivity
You can adjust the microphone’s sensitivity if the XLR terminal switch is set to MIC or MIC+48V.
78
1 Open the desired XLR terminal’s sensitivity submenu.
[¡ Audio Setup] > [Audio Input] > [XLR1 Mic Trimming] or [XLR2 Mic Trimming]
2 Select the desired level and then press the joystick.
Available Sensitivity Levels
+12 dB
+6 dB
0 dB
-6 dB
[¡ Audio Setup]
-12 dB
[Audio Input]
[XLR1 Mic Trimming]
[XLR2 Mic Trimming]
[0 dB]
Activating the Microphone’s Attenuator
You can activate the microphone’s attenuator (20 dB) if the XLR terminal
switch is set to MIC or MIC+48V.
Y
P
O
1 Open the desired XLR terminal’s microphone attenuator submenu.
[¡ Audio Setup] > [Audio Input] > [XLR1 Mic Att.] or [XLR2 Mic
Att.]
2 Select [On] and then press the joystick.
C
[¡ Audio Setup]
[Audio Input]
[XLR1 Mic Att.]
[XLR2 Mic Att.]
[Off]
Monitoring the Audio with Headphones
Connect headphones* to the × (headphone) terminal to monitor the
recorded audio. You can adjust the headphone volume with the
[¡ Audio Setup] > [Audio Output] > [Headphone Volume] setting.
× (headphone)
terminal
* For 50.00 Hz recordings, use commercially available headphones with a cable no
longer than 3 m.
NOTES
• If you set an assignable button to [Headphone +] or [Headphone -]
(A 85), you can press the button to adjust the headphone volume
without using the menu.
• When you are monitoring the audio, you can choose to synchronize the
audio signal with the video signal or monitor the audio in real time. Use
the [¡ Audio Setup] > [Audio Output] > [Monitor Delay] setting to
select the method. Note that there will be a slight delay when you monitor in real time. Regardless of the
setting, however, the audio and video signals recorded will be synchronized.
Color Bars/Audio Reference Signal
Color Bars/Audio Reference Signal
You can have the camcorder generate and record color bars and a 1 kHz audio reference signal and output
them from the HDMI OUT terminal, AV OUT terminal and × (headphone) terminal (audio reference signal only).
79
Operating modes:
Recording Color Bars
The types of color bars available depend on the camcorder's system
frequency setting. When [System Frequency] is set to [59.94 Hz], you can
choose between SMPTE standard-definition color bars and ARIB multiformat HDTV color bars. When [System Frequency] is set to [50.00 Hz],
you can choose between EBU color bars and SMPTE standard-definition
color bars.
[~ Camera Setup]
[Color Bars]
[Type]
[SMPTE] or [EBU]*
1 Open the color bars [Type] submenu.
[~ Camera Setup] > [Color Bars] > [Type]
2 Select the type of color bars and then press the joystick.
* Depending on the country/region of
purchase.
3 Open the [Enable] submenu to activate the color bars.
[~ Camera Setup] > [Color Bars] > [Enable]
4 Select [On] and then press the joystick.
Y
P
O
• The selected color bars appear on the screen and will be recorded
when you press the START/STOP button.
• Turning the camcorder off or changing the operating mode to
mode will deactivate the color bars.
C
[~ Camera Setup]
[Color Bars]
[Enable]
[Off]
NOTES
• If you set an assignable button to [Color Bars] (A 85), you can press the button to activate and deactivate the
color bars.
Recording an Audio Reference Signal
The camcorder can output a 1 kHz audio reference signal with the color
bars.
[¡ Audio Setup]
[Audio Input]
1 Open the [1 kHz Tone] submenu.
[¡ Audio Setup] > [Audio Input] > [1 kHz Tone]
2 Select the desired level and then press the joystick.
[1 kHz Tone]
[Off]
• Available levels are -12 dB, -18 dB and -20 dB.
• Select [Off] to turn off the signal.
• The signal is output at the selected level and will be recorded when you press the START/STOP button.
Video Scopes
Video Scopes
The camcorder can display a simplified waveform monitor or an edge monitor* to help you focus. The video
scopes appear only on the LCD screen. They do not appear in the viewfinder or on an external monitor.
80
* The edge monitor looks at the focus of the entire picture and displays the results as a waveform. The edge monitor is available
only in
mode.
Displaying a Video Scope
Operating modes:
Press the WFM button.
• The waveform monitor will appear in a window on the lower right of the
screen.
• You can press the WFM button repeatedly to activate the video scopes
in the following sequence.
Waveform monitor Edge monitor* Off
• Alternatively, you can display the video scopes using [w Other
Functions] > [WFM (LCD)] > [Setting]. Select [WFM] for the waveform
monitor or [Edge Mon.]* for the edge monitor.
* Not available in
mode.
Configuring the Waveform Monitor
C
Y
P
O
The camcorder’s waveform monitor function offers 5 modes. You can also
change the gain.
[w Other Functions]
[WFM (LCD)]
Operating modes:
[Waveform Monitor]
1 Open the [Waveform Monitor] submenu.
[w Other Functions] > [WFM (LCD)] > [Waveform Monitor]
[Line]
2 Select the desired option and then press the joystick.
• If you do not need to change the gain, you do not need to perform steps 3 and 4.
3 Open the waveform monitor [Gain] submenu.
[w Other Functions] > [WFM (LCD)] > [Gain] (under [Waveform Monitor])
4 Select [1x] or [2x] and then press the joystick.
Options
[Line]:
[Line+Spot]:
[Field]:
[RGB]:
[YPbPr]:
Sets the waveform monitor to line display mode.
The waveform of the area in the red frame is displayed in red on top of the [Line] mode waveform.
Sets the waveform monitor to field display mode.
Functions like an RGB parade scope.
Functions like a YPbPr parade scope.
Video Scopes
Configuring the Edge Monitor
[w Other Functions]
Using this video scope allows you to focus with more precision. You can
use the edge monitor along with the other focus assistance functions
(A 66). The edge monitor features 2 modes.
[WFM (LCD)]
[Edge Monitor]
Operating modes:
1 Open the [Edge Monitor] submenu.
[w Other Functions] > [WFM (LCD)] > [Edge Monitor]
[Type 1]
2 Select the desired option and then press the joystick.
• If you do not need to change the gain, you do not need to perform steps 3 and 4.
3 Open the edge monitor [Gain] submenu.
[w Other Functions] > [WFM (LCD)] > [Gain] (under [Edge Monitor])
4 Select the desired gain value and then press the joystick.
Options
[Type 1]:
[Type 2]:
The waveform that represents the focus of the entire picture is displayed in green. In addition, the waveform
of the area in the three red frames is displayed in red on top of the previous waveform.
This mode displays the edge monitor with the waveform monitor in [Line+Spot] mode. The waveform
monitor appears on the left in green while the edge monitor appears on the right in blue. The waveform of
the area in the red frame is displayed in red on top of the edge monitor waveform.
C
Y
P
O
81
Reviewing a Recording
Reviewing a Recording
82
When the camcorder is in
was recorded.
mode, you can review the last clip that
[w Other Functions]
Operating modes:
[Rec Review]
1 Open the [Rec Review] submenu to set the review length.
[w Other Functions] > [Rec Review]
2 Select the desired option and then press the joystick.
3 After you finish recording, press the u button.
• The last clip that was recorded is played back without audio for the
selected duration. [Ð REVIEW] appears at the top of the screen.
• Press the CANCEL button to stop reviewing the clip and change the
camcorder back to record pause mode.
• After the clip finishes playing back, the camcorder returns to record
pause mode.
Options
[Entire Clip]:
[Last 4 sec]:
Allows you to review the entire clip.
Allows you to review just the last 4 seconds of the clip.
Y
P
O
NOTES
• When pre-recording mode is activated (A 83), you cannot review a clip.
• If the camcorder switched SD cards during a recording, the camcorder
will play back the clip on the SD card most recently recorded on.
C
[Entire Clip]
Pre-recording Mode
Pre-recording Mode
When pre-recording mode is activated, the camcorder starts recording continuously into a temporary memory of
approximately 3 seconds so when you press the START/STOP button, the clip will contain also approximately 3
seconds of video and audio recorded before you pressed the button. This is especially useful when it is difficult
to predict when to start recording.
Operating modes:
1 Open the [Pre Rec] submenu.
[w Other Functions]
[w Other Functions] > [Pre Rec]
2 Select [On] and then press the joystick.
[Pre Rec]
• [PRE REC STBY] appears at the top of the screen.
3 Press the START/STOP button to begin recording.
[Off]
• The rear and front tally lamps illuminate.
• [PRE REC STBY] changes to [Ü PRE REC] while recording.
4 Press the START/STOP button again to stop recording.
• The camcorder records the clip, including approximately 3 seconds of video and audio recorded before the
START/STOP button was pressed.
• Both tally lamps will go out and [PRE REC STBY] appears at the top of the screen.
Y
P
O
NOTES
• During pre-recording mode, if the camcorder is left in record pause mode for approximately 1 hour, a message
will be displayed (A 146). After about 1 minute, pre-recording will be deactivated automatically.
• Pre-recording mode cannot be used with double slot recording, deleting the last clip recorded or reviewing a
recording.
• During pre-recording mode, the time code will be recorded with the running mode (A 69) set to [Free Run],
regardless of the previous setting. When the time code is recorded, it will include the 3 seconds before the
START/STOP button was pressed. When pre-recording mode is deactivated, the running mode will return to
its previous setting.
C
83
Pre-recording Mode
84
C
Y
P
O
4
Customization
85
Assignable Buttons
The camcorder conveniently features 15* buttons to which you can assign various functions. By assigning oftenused functions, you can quickly access them with a single press of a button. Assignable button 7 is located on
the grip unit, so its availability depends on the camcorder configuration used.
* In
mode, only assignable buttons 7 to 15 are available.
Operating modes:
C
Y
P
O
(on the grip unit)
Changing the Assigned Function
1 Open the [Assign Button] submenu.
[w Other Functions] > [Assign Button]
[w Other Functions]
[Assign Button]
2 Select the button to change and then press the joystick.
• A list of available functions appears.
• The quick reference shows the default settings for each assignable
button. The labels on the camcorder/grip unit for assignable buttons
7 to 15 also indicate their default settings. By default, buttons 1 to 6
have no assignable function set.
3 Select the desired function and then press the joystick.
• If you selected [User Setting (NONE)], the menu will change from
orange to blue to indicate you are selecting a menu setting to register.
Continue the procedure to register a menu setting. Otherwise, you do
not need to perform the rest of the procedure.
[1 to 6 (NONE)]
[7 MAGN.]
[8 MAGN.]
[9 PEAKING]
[10 ZEBRA]
[11 WFM]
[12 PUSH AUTO IRIS]
[13 ISO/GAIN]
[14 SHUTTER]
[15 ONE-SHOT AF]
Assignable Buttons
4 Navigate the menus to find the menu setting you want to register and then press the joystick.
86
• The selected menu setting will be registered to the customizable slot and to the assignable button.
• The name of the selected menu setting will be listed instead of [User Setting (NONE)] and the customizable
slot will be marked by a .
NOTES
• You can check the two [Assign Button] status screens (A 136) to see what functions are set for the
assignable buttons.
• You can reset only the functions assigned to the assignable buttons, without affecting other camera settings,
with the [w Other Functions] >[Reset] > [Assignable Buttons] function. All the assignable buttons will return
to their default function.
Using an Assignable Button
After you assign a function to one of the buttons, press the button to activate the function. For some functions,
an options menu may appear. In such case, select the desired option and then press the joystick.
Assignable Functions
Functions can be set separately in
functions and available modes.
mode and
Function name
mode. Refer to the following table for assignable
A
Description
Y
P
O
[ONE-SHOT AF]
The camcorder focuses automatically one time only (One-shot AF function).
Ü
–
64
[PUSH AUTO IRIS]
The camcorder automatically adjusts the aperture (f/stop).
Ü
–
60
[Iris +]
Opens up the aperture.
Ü
–
[Iris -]
Closes the aperture.
Ü
–
[AE Shift +]
Compensates the exposure toward the bright side.
Ü
–
[AE Shift -]
Compensates the exposure toward the dark side.
Ü
–
[Backlight]
Turns the [Backlight] light metering option on/off.
Ü
–
[Spotlight]
Turns the [Spotlight] light metering option on/off.
Ü
–
[ISO/GAIN]
Highlights the ISO speed or gain value so it can be adjusted.
Ü
–
56
[SHUTTER]
Highlights the shutter speed so it can be adjusted.
Ü
–
53
[View Assist.]
Turns view assistance on/off.
Ü
–
97
[PEAKING]
Turns peaking on/off.
Ü
–
66
[ZEBRA]
Turns zebra patterns on/off.
Ü
–
68
[WFM]
Activates video scopes in the following sequence:
Waveform monitor J Edge monitor (
mode only) J Off
Ü
Ü
80
[MAGN.]
Turns magnification on/off.
Ü
–
66
[Color Bars]
Turns color bars on/off.
Ü
–
79
[Markers]
Turns onscreen markers on/off.
Ü
–
67
[LCD Setup]
Opens the [LCD Setup] submenu.
Ü
Ü
[VF Setup]
Opens the [VF Setup] submenu.
Ü
Ü
[LCD/VF B&W]
Turns the B&W mode of the LCD and viewfinder on/off.
Ü
Ü
33
[Onscreen Display]
Turns on/off the inclusion of onscreen displays on video output from the camcorder’s
terminals (both HD and SD video output).
Ü
Ü
114
[Time Code]
Displays the [Time Code] submenu.
Ü
–
69
[Time Code Hold]*
Puts the time code display on hold or resumes it.
Ü
Ü
70
[Headphone +]
Increases the headphone volume.
Ü
Ü
[Headphone -]
Reduces the headphone volume.
Ü
Ü
C
59
60
61
33
104
Assignable Buttons
Function name
A
Description
[Speaker +]
Increases the built-in speaker's volume.
–
Ü
[Speaker -]
Reduces the built-in speaker's volume.
–
Ü
[Audio Output CH]
Switches the audio output channel.
Ü
Ü
115
[Audio Level]
Turns the audio level meter on/off.
Ü
Ü
74, 77
[Photo]*
Records a photo.
Ü
Ü
119
[Fan]
Switches the cooling fan’s operation between always on and automatic.
Ü
–
36
[My Menu]
Opens the [My Menu] customized submenu.
Ü
–
28
[Initialize Media]
Opens the [Initialize Media] submenu.
Ü
Ü
40
[User Setting
(NONE)]*
Customizable slot. Assign to the button any menu setting you would like to register.
Ü
Ü
–
* Function can be used only by assigning it to a button.
C
Y
P
O
104
87
Custom Picture Settings
Custom Picture Settings
88
You can preset a number of picture-related settings (A 91). You can change each individual setting for
maximum control or use a more intuitive graphical interface to adjust the gamma curve and white balance shift
(A 96). After adjusting the desired settings to your preference, you can save the whole set in the camcorder or
SD card as a custom picture file. You can then load the file at a later date to change the current settings to the
preset levels you selected. You can even use the [w Other Functions] > [Photos] > [Add / File] setting to
embed the custom picture settings in photos recorded to an SD card.
You can save up to 9 different custom picture files on the camcorder and up to 20 custom picture files on an SD
card. Custom picture files can be copied between the camcorder and SD card.
Custom picture files created with previous Canon camcorders are not compatible with this camcorder. Custom
picture files created with this camcorder are compatible only with other C100 camcorders.
Operating modes:
Selecting Custom Picture Files
Select a custom picture file to apply its settings to your recordings or to
edit, rename, protect, or transfer it. When [~ Camera Setup] >
[/ CINEMA Locked] is set to [On], the custom picture menu cannot be
accessed and custom picture files cannot be used.
1 Press the CUSTOM PICTURE button.
Y
P
O
• The custom picture menu appears. The currently selected file
appears next to the - icon or [Off] if no file is selected.
C
2 Select [- / Select File] and then press the joystick.
3 Select the location of the custom picture file and then press the
joystick.
• Select [Camera] to apply a custom picture file saved in the camcorder
or [*A] or [*B] to apply a custom picture file saved on the
respective SD card.
• [*A] and [*B] will only appear if the SD card contains previously saved custom picture files.
4 Select the desired file and then press the joystick.
• Select [Off] to record without applying any custom picture settings.
• To apply the file’s settings, press the CUSTOM PICTURE button to exit the custom picture menu. An icon
representing the selected custom picture file will appear on the left of the screen.
• To perform other operations on the file, continue with the following procedures.
Preset Custom Picture Files
By default, the custom picture files in the camcorder in file slots [C7] to [C9] are protected. Remove the
protection (A 89) to edit the file. The following describes when to use the preset files.
[C7: EOS Std.]: Reproduces the image quality and look (high contrast, vibrant colors) of an EOS digital SLR
camera with its picture style set to [Standard].
[C8: Wide DR]: Applies a gamma curve with a very wide dynamic range and an appropriate color matrix that
nevertheless do not require post-production processing.
[C9: CINEMA]: Uses the Canon Log gamma and color matrix for an outstanding dynamic range and an
image suitable for processing in post-production.
Custom Picture Settings
Editing a Custom Picture File’s Settings
This procedure describes how to change the custom picture settings in detail when you want maximum control
over the image. In addition, the camcorder offers an easier, more intuitive way to adjust only the gamma curve
and white balance settings using a simplified graphical interface (A 96).
1 After selecting a file, select [
/ Fine Tuning] and then press the joystick.
2 Select a setting and then press the joystick.
3 Change the setting to the desired level and then press the joystick.
• Refer to Available Custom Picture Settings (A 91) for details on the various settings.
• Repeat steps 2 and 3 for other settings, as necessary.
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the new custom
picture settings.
Resetting the current file’s settings to default values
1 After selecting a file, open the [Reset] submenu.
[
[
/ Fine Tuning] > [Reset]
/ Fine Tuning]
[Reset]
2 Select the desired default values and then press the joystick.
• Select [NEUTRAL] to reset to neutral default values (equivalent to not
using custom picture settings at all) or one of the preset settings ([CINEMA], [Wide DR] or [EOS Std.]) if you
want to replicate these preset settings, for example as a starting point to edit them further.
3 Select [OK] and then press the joystick.
C
Y
P
O
Renaming Custom Picture Files
1 After selecting a file, open the [Rename] submenu.
[ / Fine Tuning] > [Rename]
[
/ Fine Tuning]
[Rename]
• A screen appears that displays the current file name with an orange
selection frame on the first character.
2 Push the joystick up/down to select an alphanumeric character or symbol and then press the
joystick to move to the next field.
• Change the rest of the name in the same way.
3 Select [Set] and then press the joystick.
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom
picture settings.
Protecting Custom Picture Files
Protecting a custom picture file prevents its settings from being
accidentally changed.
1 After selecting a file, open the [Protect] submenu.
[ / Fine Tuning] > [Protect]
[
/ Fine Tuning]
[Protect]
89
Custom Picture Settings
2 Select [Protect] and then press the joystick.
• In the custom picture menu, i will appear next to the file name.
• To remove protection settings, select [Unprotect] instead.
90
3 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom
picture settings.
Transferring Custom Picture Files
You can transfer custom picture files between the camcorder and SD cards. When the custom picture file is in
the camcorder, use [Copy To *] or [Load From *] depending on the operation you wish to perform. Similarly,
when the custom picture file is on an SD card, use [Copy To Cam.] or [Load From Cam]. Custom picture files
cannot be copied directly from one SD card to another.
Copying a File from the Camcorder to an SD Card
1 After selecting a file in the camcorder, open the [Copy To *] submenu.
[+ / Transfer File] > [Copy To *]
[+ / Transfer File]
[Copy To *]
2 Select [*A] or [*B] and then press the joystick.
3 Select the file slot on the SD card under which to save the file and then
press the joystick.
• If there are available slots, you can select [New File] to save the file in the first available slot.
Y
P
O
4 Select [OK] and then press the joystick.
• The currently selected file will be copied to the selected slot on the SD card, overwriting the file in that slot.
When the confirmation screen appears, press the joystick.
C
5 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
Replacing a File in the Camcorder with a File on an SD Card
1 After selecting a file in the camcorder to replace, open the [Load
From *] submenu.
[+ / Transfer File] > [Load From *]
[+ / Transfer File]
[Load From *]
2 Select [*A] or [*B] and then press the joystick.
3 Select the file to transfer to the camcorder and then press the joystick.
4 Select [OK] and then press the joystick.
• The file in the camcorder will be overwritten by the one on the SD card. When the confirmation screen
appears, press the joystick.
5 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
Copying a File from an SD Card to the Camcorder
1 After selecting a file on an SD card, open the [Copy To Cam.] submenu.
[+ / Transfer File] > [Copy To Cam.]
[+ / Transfer File]
[Copy To Cam.]
2 Select the file slot under which to save the file and then press the
joystick.
3 Select [OK] and then press the joystick.
• The currently selected file will be copied to the selected slot on the camcorder, overwriting the file in that
slot. When the confirmation screen appears, press the joystick.
Custom Picture Settings
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
Replacing a File on an SD Card with a File in the Camcorder
[+ / Transfer File]
1 After selecting a file on an SD card to replace, open the [Load From
Cam.] submenu.
[+ / Transfer File] > [Load From Cam.]
[Load From Cam.]
2 Select the file to transfer to the SD card and then press the joystick.
3 Select [OK] and then press the joystick.
• The file on the SD card will be overwritten by the one in the camcorder. When the confirmation screen
appears, press the joystick.
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
NOTES
• You can also copy a custom picture file embedded in a photo to the camcorder (A 125).
Available Custom Picture Settings
The following are the available settings. Even if no custom picture file is selected, the default settings are still
applied to the picture.
[Gamma]
C
Y
P
O
The gamma curve changes the overall look of the image. Generally, this should be the same setting as [Select]
under [Color Matrix]. (Default: [Normal 1]).
[Normal 1] to [Normal 4]: These settings are suitable for viewing the image on a TV monitor. Highlights in [Normal
2] are brighter than those of [Normal 1]. Dark tones in the lower part of the gamma
curve for [Normal 3] (ITU-R BT.709 standard) and [Normal 4] are more pronounced than
those of [Normal 2].
[Cine 1] or [Cine 2]:
Use [Cine 1] for a gamma curve that results in a picture with a cinema-like feel and
cinema-like tones. [Cine 2] has softer contrasts than does [Cine 1] but is also suitable
for creating a cinema-like picture.
[EOS Std.]:
This gamma curve approximates the look of an EOS digital SLR camera when the
picture style is set to [Standard] (high contrast, vibrant colors).
[Wide DR]:
Applies a gamma curve with a very wide dynamic range, optimized for playback on an
HDTV.
[Canon Log]:
Applies a logarithmic gamma curve for outstanding dynamic range. Requires image
processing in post-production.
Gamma
Canon log
Cine 1
Cine 2
Output
Output
Normal 2/3/4
Normal 1
Wide DR Gamma
Canon Log
Normal 4
Normal 3
Normal 1/2
Input
Input
91
Custom Picture Settings
[Black]
[Master Black]
Corrects color cast in blacks.
[Red]: -50 to 50 (Default: ±0)
[Green]: -50 to 50 (Default: ±0)
[Blue]: -50 to 50 (Default: ±0)
[Black Gamma]
Controls the lower part of the gamma curve (dark areas of the image). When [Gamma] is set to [Wide DR] or
[Canon Log], this setting has no effect on the picture.
[Level]: Raises or lowers the lower part of the gamma curve. This setting can be adjusted from -50 to 50.
(Default: ±0)
[Range]: Selects the range in which dark areas are affected. This setting can be adjusted from -5 to 50.
(Default: ±0)
[Point]: Determines the shape of the lower part of the gamma curve. This setting can be adjusted from -1 to 50.
(Default: ±0)
Black Gamma
C
Y
P
O
Output
92
Controls the black level and color cast of blacks.
[Master Pedestal]
The master pedestal increases or decreases the black level. Higher settings will make dark areas brighter but
decrease contrast. This setting can be adjusted from -50 to 50. (Default: ±0)
Point
Input
[Low Key Satur.]
Adjusts color saturation in dark areas.
[Enable]: Activates/deactivates the setting. (Default: [Off])
[Level]: Specifies how saturated colors are in dark areas. This setting can be adjusted from -50 to 50. (Default:
±0)
[Knee]
Controls the upper part of the gamma curve (highlights of the image). By compressing the highlights, you can
prevent parts of the image from being overexposed. When [Gamma] is set to [Cine 1], [Cine 2], [EOS Std.], [Wide
DR] or [Canon Log], this setting has no effect on the picture.
[Enable]:
Activates/deactivates the setting. (Default: [On])
[Slope]:
Determines the slope of the gamma curve above the knee point. This setting can be adjusted from
-35 to 50. (Default: ±0)
[Point]:
Sets the knee point of the gamma curve. This setting can be adjusted from 50 to 109. (Default: 95)
[Saturation]: Adjusts color saturation in highlights. This setting can be adjusted from -10 to 10. (Default: ±0)
Custom Picture Settings
Knee Slope
Knee Point
Output
Output
93
Input
Input
[Sharpness]
Sets the sharpness of the output and recording signal.
[Level]:
Sets the sharpness level. This setting can be adjusted from -10 to 50. (Default: ±0)
[H Detail Freq.]: Sets the center frequency of horizontal sharpness. Setting higher values increases the
frequency, which, in turn, increases the sharpness. This setting can be adjusted from -8 to 8.
(Default: ±0)
[Coring]:
Reduces noise artifacts caused by high sharpness levels.
[Level]: Sets the coring level. Higher values prevent sharpness from being applied to minute details, resulting in
less noise. This setting can be adjusted from -30 to 50. (Default: ±0)
[D-Ofst]: You can use [D-Ofst], [D-Curve] and [D-Depth] to adjust the coring level based on brightness. [D-Ofst]
sets the coring level of the minimum brightness level. This setting can be adjusted from 0 to 50. (Default: 0)
[D-Curve]: Sets the curve of the coring adjustment. This curve is the change from [Level] to [D-Ofst]. This setting
can be adjusted from 0 to 8. (Default: 0)
[D-Depth]: Sets a multiplier to [D-Ofst] that determines the coring level adjustment based on brightness.
Positive values raise the coring level in dark areas and negative values lower the level. This setting can be
adjusted from -4 to 4. (Default: ±0)
[HV Detail Bal.]: Adjusts the ratio between horizontal and vertical detail. Higher values emphasize vertical detail
while lower values emphasize horizontal detail. This setting can be adjusted from -8 to 8.
(Default: ±0)
[Limit]:
Restricts how much sharpness is applied. This setting can be adjusted from -50 to 50.
(Default: ±0)
[Select]:
In addition to the sharpness set by [Level], [Select] sets the sharpness for areas with higher
frequencies. Higher values apply more sharpness to areas with higher frequencies. Use this for
subjects in which normal sharpening is not effective. This setting can be adjusted from 0 to 15.
(Default: 0)
[Knee Aperture]: Allows you to set the sharpness of only the areas above the knee point by adjusting the gain and
slope. This is not available when [Gamma] is set to [Cine 1], [Cine 2], [Canon Log] or [EOS Std.].
[Gain]: Sets the amount of sharpness. This setting can be adjusted from 0 to 9. (Default: 0)
[Slope]: Sets the slope of the sharpness. This setting can be adjusted from 0 to 3, with 0 having no slope, 1
having a steep slope and 3 having a gradual slope. (Default: 1)
[Level Depend]: Lowers the amount of sharpness applied to dark areas of the image.
[Level]: Sets the brightness of the dark areas of the image that will be affected. This setting can be adjusted
from 0 to 50. (Default: 0)
[Slope]: Determines the slope of the area between the upper and lower parts of the gamma curve. This setting
can be adjusted from 0 to 3, with 0 having no slope, 1 having a steep slope and 3 having a gradual slope.
(Default: 0)
C
Y
P
O
Custom Picture Settings
[Offset]: Adjusts the sharpness level of dark areas in the image. Setting higher values will lower the sharpness
level. This setting can be adjusted from 0 to 50. (Default: 0)
[Noise Reduction]
94
Reduces the amount of noise that appears in the image. Select a level from 1 (lowest level) to 12 (highest level),
or select [Off] to turn the noise reduction off. (Default: [Off])
[Skin Detail]
The camcorder applies a softening filter to areas in the picture with skin tones to give a more pleasant
appearance. By changing these settings, you can determine what areas will be detected as skin tones. A zebra
pattern will appear over areas on the screen that are detected as having skin tones.
[Effect Level]: Adjusts the level of the filter. The available options are [Off], [Low], [Middle] and [High]. (Default:
[Off])
[Hue]:
Adjusts the hue for detection of skin tones. This setting can be adjusted from -16 to 16.
(Default: ±0)
[Chroma]:
Adjusts the color saturation for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
[Area]:
Adjusts the color range for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
[Y Level]:
Adjusts the brightness for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
[Selective NR]
Y
P
O
The camcorder detects the characteristics of a certain color or tone and applies a noise reduction filter to the
targeted areas. A zebra pattern will appear over targeted areas on the screen.
[Effect Level]: Adjusts the level of the noise reduction filter. The available options are [Off], [Low], [Middle] and
[High]. (Default: [Off])
[Hue]:
Adjusts the hue for the color to be detected. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]:
Adjusts the color saturation for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
[Area]:
Adjusts the color range for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
[Y Level]:
Adjusts the brightness for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
C
[Color Matrix]
Color matrix affects the color tones throughout the whole image.
[Select]: Available options are [Normal 1] to [Normal 4], [Cine 1] and [Cine 2], [EOS Std.], [Wide DR] and [Canon
Log]. Generally, this should be the same setting as [Gamma]. After selecting an option, you can make
more precise adjustments. (Default: [Normal 1])
[Gain]: Adjusts the color intensity. This setting can be adjusted from -50 to 50. (Default: ±0)
[Phase]: Adjusts the color phase. This setting can be adjusted from -18 to 18. (Default: ±0)
[R-G]: The R-G matrix changes the tint of the picture along the cyan/green and red/magenta gradations. This
setting can be adjusted from -50 to 50. (Default: ±0)
[R-B]: The R-B matrix changes the tint of the picture along the cyan/blue and red/yellow gradations. This
setting can be adjusted from -50 to 50. (Default: ±0)
[G-R]: The G-R matrix changes the tint of the picture along the magenta/red and green/cyan gradations. This
setting can be adjusted from -50 to 50. (Default: ±0)
[G-B]: The G-B matrix changes the tint of the picture along the magenta/blue and green/yellow gradations.
This setting can be adjusted from -50 to 50. (Default: ±0)
[B-R]: The B-R matrix changes the tint of the picture along the yellow/red and blue/cyan gradations. This
setting can be adjusted from -50 to 50. (Default: ±0)
Custom Picture Settings
[B-G]:
The B-G matrix changes the tint of the picture along the yellow/green and blue/magenta gradations.
This setting can be adjusted from -50 to 50. (Default: ±0)
[White Balance]
Adjusts the amount of white balance throughout the whole image.
[R Gain]: Adjust the intensity of red tones. This setting can be adjusted from -50 to 50. (Default: ±0)
[B Gain]: Adjust the intensity of blue tones. This setting can be adjusted from -50 to 50. (Default: ±0)
[Color Correction]
The camcorder detects the characteristics of a certain color (color phase, chroma, area and Y level) and corrects
them when recording. You can set the color correction for up to two different areas (A and B).
[Select Area]: Selects the area or areas to correct. Available options are [Area A], [Area B] and [Area A&B].
Select [Off] to turn this setting off. (Default: [Off])
[Area A Setting]: Determines the area in which colors will be corrected.
[Phase]: Adjusts the color phase for area A. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]: Adjusts the color saturation for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Area]: Adjusts the color range for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Y Level]: Adjusts the brightness for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Area A Revision]: Sets the amount of correction for area A.
[Level]: Adjusts the amount of correction to the color saturation. This setting can be adjusted from -50 to 50.
(Default: ±0)
[Phase]: Adjusts the amount of correction to the color phase. This setting can be adjusted from -18 to 18.
(Default: ±0)
[Area B Setting]: Determines the area in which colors will be corrected.
[Phase]: Adjusts the color phase for area B. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]: Adjusts the color saturation for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Area]: Adjusts the color range for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Y Level]: Adjusts the brightness for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Area B Revision]: Sets the amount of correction for area B.
[Level]: Adjusts the amount of correction to the color saturation. This setting can be adjusted from -50 to 50.
(Default: ±0)
[Phase]: Adjusts the amount of correction to the color phase. This setting can be adjusted from -18 to 18.
(Default: ±0)
C
Y
P
O
[Other Functions]
[Setup Level]: Adjusts the black level set by the [Black] and [Master Pedestal] settings.
[Level]: Determines the amount of adjustment to be made. This setting can be adjusted from -50 to 50.
(Default: ±0)
[Press]: Compresses the dynamic range of the video signal so that it does not exceed 100%. Available options
are [On] and [Off]. (Default: [Off])
[Clip At 100%]: When the video signal exceeds 100%, this function clips the white level at 100%. Available
options are [On] and [Off]. (Default: [Off])
95
Custom Picture Settings
Simplified Graphical Interface
96
In addition to the very detailed settings explained in the previous section (A 91), the camcorder offers a more
intuitive graphical interface for adjusting the gamma curve and white balance settings. Instead of remembering
numeric values, you can see how your changes affect the gamma curve or white balance shift right on the
screen.
Gamma Curve
[, / Edit File]
1 After selecting a file, open the gamma curve adjustment screen.
[, / Edit File] > [Gamma]
• The current gamma curve will be displayed on the screen.
[Gamma]
2 Push the joystick left/right to highlight the [M] field and then push the
joystick up/down to select the desired basic gamma curve.
• The numbers correspond to the [Gamma] settings explained
previously (A 91), as follows:
1 to 4: [Normal 1] to [Normal 4]
5 and 6: [Cine 1] and [Cine 2]
7: [EOS Std.]
8: [Wide DR]
9: [Canon Log]
3 Push the joystick left/right to highlight the [H] field or [L] field and then
push the joystick up/down to adjust the gamma curve as necessary.
• The [L] value can be adjusted from 1 to 9. It is equivalent to the [Black Gamma] setting and controls the
lower part of the gamma curve (dark areas of the image). This setting is not available when the [M] value is
set to 8 or 9.
• The [H] value can be adjusted from 1 to 5. It is equivalent to the [Knee] setting and controls the upper part of
the gamma curve (highlights of the image). This setting is not available when the [M] value is set to 5 or
higher.
C
Y
P
O
4 Push the joystick left/right to select [Set] and then press the joystick.
• The adjusted gamma curve will be saved. The [Gamma] value under the [
change accordingly.
/ Fine Tuning] submenu will
5 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
White Balance
1 After selecting a file, open the white balance shift screen.
[, / Edit File] > [White Balance]
• The current white balance is shown as an orange point at the
center of the WB correction coordinates.
[, / Edit File]
[White Balance]
2 Push the joystick left/right to shift the white balance along the blue
(B)/amber (A) gradation. Push the joystick up/down to shift the white
balance along the green (G)/magenta (M) gradation.
• The white balance shift can be set to one of 9 levels in each
color's direction.
• The amount of white balance shift will be displayed as two
coordinates in the [SHIFT] box to the left of the graph.
3 Press the joystick.
• The adjusted white balance shift value will be saved. The [White Balance] value under the [
Tuning] submenu will change accordingly.
/ Fine
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
Custom Picture Settings
Canon Log Gamma
The Canon Log gamma setting makes full use of the newly developed sensor to offer spectacular dynamic
range. Clips recorded using Canon Log gamma need to be processed in post-production by applying a LUT
(look-up table). By fine-tuning the LUT you use in post-production you can perfectly realize the artistic vision you
desire. For more details about available LUTs, visit your local Canon Web site.
Checking Clips Recorded with Canon Log Gamma
When Canon Log gamma is used, the image displayed on the screen will appear darker than usual. You can use
the view assistance function to display an image that approximates the one that would be obtained using a
normal gamma setting. View assistance is only applied on the camcorder screen; it will not affect your recordings
or the video signal output from the various terminals.
1 Open the [View Assist.] submenu.
[£ LCD/VF Setup] > [View Assist.]
[£ LCD/VF Setup]
2 Select [On] and then press the joystick.
•
will appear on the lower left of the screen.
[View Assist.]
[Off]
C
Y
P
O
97
Customizing Functions and Onscreen Displays
Customizing Functions and Onscreen Displays
98
Customize the camcorder to match your shooting style and needs. Use the [w Other Functions] > [Custom
Function] setting to adjust how some of the camcorder’s controls and functions operate in
mode.
Similarly, use the [£ LCD/VF Setup] > [Custom Display 1] or [Custom Display 2] setting to customize the
onscreen displays that appear during recording. You can save these preferences along with other menu settings
to an SD card and use them again later (A 99).
Customizing Functions
The following table describes which functions can be customized using
[Custom Function].
[w Other Functions]
[Custom Function]
Operating modes:
1 Open the [Custom Function] submenu.
[w Other Functions] > [Custom Function]
2 Select the desired function.
3 Change the setting option and then press the joystick.
Customizable Functions with [Custom Function]
Menu item
Y
P
O
Description
[Shockless WB]
When this function is set to [On], it creates a softer transition when the white balance is changed.
[AE Response]
Controls the camcorder’s response ([Fast], [Normal] or [Slow]) when you change the automatic exposure setting.
[Grip Ctrl Dial Dir.]
Changes the direction of the adjustment ([Normal] or [Reverse]) when operating the control dial on the grip unit.
[F. Assist. B&W]
Automatically switches the screen to B&W while the focus assist functions (peaking and magnification) are activated. You
can have the screen switch to B&W only when peaking is activated ([Peaking]), only when the magnification is activated
([Magnify]) or when either function is activated ([Both]).
[Magn. Add. Disp.]
Simultaneously activates peaking ([Peaking]) or displays the edge monitor ([Edge Mon.]) whenever the magnification
function is used.
[Scan Reverse Rec]
Inverts the recorded image horizontally ([Horizontal]), vertically ([Vertical]) or both ([Both]).
[Character Rec]
When this function is set to [On], all of the onscreen displays will be recorded to the clip exactly as they appear on the screen.
C
Customizing Onscreen Displays
For details on which onscreen displays can be customized, refer to
Onscreen Displays (A 48). For details on the setting options, refer to
[Custom Display 1] and [Custom Display 2] (A 130).
Operating modes:
1 Open the [Custom Display 1] or [Custom Display 2] submenu.
[£ LCD/VF Setup] > [Custom Display 1] or [Custom Display 2]
2 Select the desired onscreen display.
3 Change the setting option and then press the joystick.
[£ LCD/VF Setup]
[Custom Display 1]
[Custom Display 2]
Saving and Loading Camera Settings
Saving and Loading Camera Settings
After you adjust custom picture settings and settings in the various menus, you can save those settings on an
SD card. You can load those settings at a later date or on another C100 camcorder so that you can use that
camcorder in that same exact way.
Operating modes:
Saving Camera Settings to an SD Card
[w Other Functions]
1 Open the [Save To *] submenu.
[w Other Functions] > [Transfer Menu//] > [Save To *]
[Transfer Menu//]
2 Select [*A] or [*B] and then press the joystick.
3 Select [Menu] or [Menu+/] and then press the joystick.
• Selecting [Menu] will save menu settings and [Menu+/] will save
[Save To *]
menu and custom picture settings.
4 Select [OK] and then press the joystick.
• The current settings are saved to the SD card. If the SD card already has camera settings on it, they will be
overwritten.
Y
P
O
5 When the confirmation screen appears, press the joystick.
C
Loading Camera Settings from an SD Card
1 Open the [Load From *] submenu.
[w Other Functions] > [Transfer Menu//] > [Load From *]
[w Other Functions]
[Transfer Menu//]
2 Select [*A] or [*B] and then press the joystick.
3 Select [Menu] or [Menu+/] and then press the joystick.
• Selecting [Menu] will load menu settings and [Menu+/] will load
[Load From *]
menu and custom picture settings.
4 Select [OK] and then press the joystick.
5 When the confirmation screen appears, press the joystick.
NOTES
• The SD card includes a text file that lists the camera settings. You can check the settings by using a USB card
reader to access the SD card on a computer. In the “PRIVATE\CAMSET” folder, open the file “CAMSET4.TXT”.
• When loading camera settings from an SD card, even protected custom picture files in the camcorder will be
replaced.
• Only camera settings from other Canon C100 camcorders can be used with this camcorder.
99
Saving and Loading Camera Settings
100
C
Y
P
O
5
Playback
101
Playback
This section explains how to play back clips recorded on an SD card. For details on playing back clips using an
external monitor, refer to Connecting to an External Monitor (A 112). For details on viewing photos, refer to
Viewing Photos (A 121).
Operating modes:
Clip Index Screen
Playback functions are accessed from the clip index screen. To open
the clip index screen, set the camcorder to
mode.
Set the Q switch to MEDIA.
• The camcorder switches to
mode and the clip index screen
appears.
• Clips recorded at a system frequency other than the one currently
used by the camcorder, cannot be played back. To play back such
clips, change the camcorder's system frequency (A 50) to match
the recordings on the SD card.
C
Y
P
O
5
6
1
2
3
4
7
9
8
1
2
3
4
Clip thumbnail
Recording date (month and day only) and time
Orange selection frame
Recording date and time
5
6
7
8
9
Currently selected SD card slot (A 102)
Clip number / Total number of clips
Clip's start time code
Bit rate and audio recording mode* (A 50)
Frame rate (A 50)
* The audio recording mode is only displayed for clips recorded using the [24 Mbps LPCM] bit rate.
Playback
Switching Between the SD Card Slots
If both SD card slots contain an SD card, you can switch between them as
necessary.
102
Operating modes:
Press the SLOT SELECT button.
• The access indicator of the selected SD card slot will illuminate in green.
Switching to Other Index Screens
The clip index screen shows AVCHD clips that were recorded on the SD
card using the camcorder. To view other recordings on the same SD card, you will need to open a different index
screen. Open the [Photos] index screen to view photos or the [SD Movies] index screen to access clips that were
converted to standard definition.
Operating modes:
1 Press the INDEX button.
• The index screen selection menu appears.
C
Y
P
O
2 Select the desired index screen and then press the joystick.
• The selected index screen appears.
• Select [Cancel] instead to cancel the operation.
• Press the INDEX button again to return to the clip index screen.
Playing Back Clips
You can play back clips from the clip index screen. You can control the
playback with the controls on the camcorder or with the joystick and onscreen
joystick guide.
1 Move the orange selection frame to the clip you want to play back.
2 Press the Ò button to start playback.
• Playback will start from the clip selected and continue until the end of the
last clip in the index screen. When the last frame of the last clip is reached,
playback will be paused.
• Press the Ò button again or press the joystick to pause/resume the
playback.
• Press the Ñ button to stop the playback and return to the index screen.
Playback
IMPORTANT
• Observe the following precautions while either of the SD card access indicators is illuminated in red. Failure to
do so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
NOTES
• You may notice brief stops in video or audio playback between clips.
• Playback of clips converted to standard definition (A 108) is limited to only Ð (play) and Ñ (stop). Also,
playback will stop at the end of each clip.
Onscreen Displays
5
6
1
2
3
C
4
1
2
3
4
5
6
7
8
Remaining battery time (A 49)
Temperature warning (A 36)
Joystick guide (A 104)
Recording date and time*
Playback operation
Currently selected SD card slot (A 102)
Time code (A 69)
Clip number / Total number of clips
Y
P
O
12
13
14
9 Bit rate and audio recording mode** (A 50)
10 Frame rate (A 50)
11 Onscreen displays superimposed on video output
(A 114)
12 User bit (A 72)
13 Audio output channel (A 115)
14 Audio level meter***
* Appears when [£ LCD/VF Setup] > [Date/Time] is set to [On].
** The audio recording mode is only displayed for clips recorded using the [24 Mbps LPCM] bit rate.
*** Appears when [£ LCD/VF Setup] > [Audio Level] is set to [On].
5 Playback operation
Ð PLAY
Ý PAUSE
Ô/Ó
F FWD ×
Ø F REV
7
8
9
10
11
Playback
Playback pause
Frame reverse/Frame advance
Fast playback*
Fast reverse playback*
* The playback speed (x5, x15 or x60) will also appear in the indicator.
103
Playback
Playback Controls
104
When you play back a clip, operate the buttons on the camcorder’s body or
use the joystick and joystick guide to use fast playback, play back frame-byframe or skip clips. Refer to the following table.
Available Playback Types
Playback type
Operation
Fast playback
Buttons: Press the Ø or × button.
Joystick: During playback, push the joystick up or down.
Repeat to increase the playback speed to approximately 5x J
15x J 60x the normal speed.
Frame advance/reverse
Joystick: During playback pause, push the joystick up or down.
Skip to the beginning of
the next clip
Buttons: Press the Ù button.
Joystick: Push the joystick right.
Skip to the beginning of
the current clip
Buttons: Press the Ú button.
Joystick: Push the joystick left.
Skip to the previous clip
Buttons: Press the Ú button twice.
Joystick: Push the joystick left twice.
Return to playback mode
Buttons: Press the Ò button.
Joystick: Press the joystick itself.
Y
P
O
NOTES
• There is no audio during any of the playback types listed in the previous table.
• During some special playback modes, you may notice some anomalies (blocky video artifacts, banding, etc.)
in the playback picture.
• The speed indicated on the screen is approximate.
• You can press the DISP. button to turn the joystick guide display on and off.
C
Adjusting the Volume
During playback, audio will come from the monaural built-in speaker or
headphones. When you connect headphones to the × (headphone)
terminal, the built-in speaker will be muted.
1 Open the [Headphone Volume] or [Speaker Volume] submenu.
[¡ Audio Setup] > [Audio Output] > [Headphone Volume] or
[Speaker Volume]
2 Select the desired level and then press the joystick.
• Select [Off] to mute the audio.
[¡ Audio Setup]
[Audio Output]
[Headphone Volume]
[Speaker Volume]
[8]
Playback
NOTES
• For details on changing the audio channel, refer to Selecting the
Audio Channel (A 115).
• If you set an assignable button to [Headphone +], [Headphone -],
[Speaker +] or [Speaker -] (A 85), you can press the button to
adjust the headphone volume or built-in speaker volume without
using the menu.
× (headphone)
terminal
Speaker
(monaural)
C
Y
P
O
105
Clip Operations
Clip Operations
106
You can use the clip menu to copy* clips, delete clips, and convert* clips to standard definition. Clip menu
functions apply only to a single clip. Selecting the same functions from the [w Other Functions] > [Clips]
submenu, you can perform the same operations on multiple clips (selected clips or all clips).
* Original AVCHD clips in the clips index screen only.
Operating modes:
Using the Clip Menu
1 Select a clip and then press the joystick.
• The clip menu appears.
2 Select the desired function and then press the joystick.
3 Select [OK] and then press the joystick to perform the operation.
• Select [Cancel] instead to cancel the operation.
4 When the confirmation message appears, press the joystick.
IMPORTANT
• Observe the following precautions while either of the SD card access indicators is illuminated in red. Failure to
do so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
C
Y
P
O
NOTES
• When performing clip operations, make sure the LOCK switch on the SD cards used is not set to prevent
writing.
Copying Clips
You can copy clips from one SD card to the other.
Copying a Single Clip
1 Select the desired clip and then press the joystick to open the clip menu.
2 Select [Copy Clip] and then press the joystick.
3 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the clip is being copied, you can press the joystick to cancel.
4 When the confirmation message appears, press the joystick.
• The selected clip is copied to the other SD card and the screen changes back to the clip index screen.
Clip Operations
Copying a Selection of Clips
[w Other Functions]
1 Open the clip selection index screen.
[w Other Functions] > [Clips] > [Copy] > [Select]
2 Using the joystick, bring the orange selection frame to a clip you wish to
copy and then press the joystick.
• A checkmark " will appear next to the clip's thumbnail to indicate it
was selected. Press the joystick again to remove the checkmark.
• Repeat this step to select all the clips you wish to copy. The total
number of selected clips will appear at the bottom of the screen, next
to the " icon.
[Clips]
[Copy]
[Select]
3 After selecting all the desired clips, press the MENU button.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the clip selection screen.
• While the clips are being copied, you can press the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Copying All Clips
[w Other Functions]
1 Open the [Clips Copy All] screen.
[w Other Functions] > [Clips] > [Copy] > [All]
Y
P
O
2 Select [OK] and then press the joystick.
• All of the clips on the selected SD card will be copied to the other SD
card.
• Select [Cancel] instead to cancel the operation.
• While the clips are being copied, you can press the joystick to cancel.
C
3 When the confirmation message appears, press the joystick.
Deleting Clips
You can delete clips you are not interested in keeping from the SD card.
Deleting a Single Clip
1 Select the desired clip and then press the joystick to open the clip menu.
2 Select [Delete Clip] and then press the joystick.
3 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the clip is being deleted, the operation cannot be canceled.
4 When the confirmation message appears, press the joystick.
[Clips]
[Copy]
[All]
107
Clip Operations
Deleting a Selection of Clips
[w Other Functions]
1 Open the clip selection index screen.
[w Other Functions] > [Clips] > [Delete] > [Select]
108
2 Using the joystick, bring the orange selection frame to a clip you wish to
delete and then press the joystick.
• A checkmark " will appear next to the clip's thumbnail to indicate it
was selected. Press the joystick again to remove the checkmark.
• Repeat this step to select all the clips you wish to delete. The total
number of selected clips will appear at the bottom of the screen, next
to the " icon.
[Clips]
[Delete]
[Select]
3 After selecting all the desired clips, press the MENU button.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the clip selection screen.
• While the clips are being deleted, you can press the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Deleting All Clips
[w Other Functions]
1 Open the [Clips Delete All] screen.
[w Other Functions] > [Clips] > [Delete] > [All]
Y
P
O
2 Select [OK] and then press the joystick.
• All of the clips on the selected SD card will be deleted.
• Select [Cancel] instead to cancel the operation.
• While the clips are being deleted, you can press the joystick to
cancel.
C
[Clips]
[Delete]
[All]
3 When the confirmation message appears, press the joystick.
Converting Clips to Standard Definition
You can convert original AVCHD clips to standard definition (MPEG-2) movies. The down-conversion to standard
definition requires two SD cards: one (source) that contains the source clips to be converted and the other one
(destination) that will store the converted files (SD movies).
Converting a Single Clip to Standard Definition
1 Select the desired clip from the index screen of the source card and then press the joystick to open the clip
menu.
2 Select [Convert HD`SD] and then press the joystick.
• The estimated size of the converted SD movie and the available space on the destination card will be
displayed on the screen.
3 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The clip will be played back as it is converted. While the clip is being converted, you can press the joystick to
cancel.
4 When the confirmation message appears, press the joystick.
• The selected clip is converted to an SD movie on the destination card and the screen changes back to the
clip index screen.
Clip Operations
Converting a Selection of Clips to Standard Definition
1 From the index screen of the source card, open the clip selection index
screen.
[w Other Functions] > [Clips] > [Convert HD`SD] > [Select]
[w Other Functions]
[Clips]
2 Using the joystick, bring the orange selection frame to a clip you wish to
[Convert HD`SD]
convert and then press the joystick.
• A checkmark " will appear next to the clip's thumbnail to indicate it
[Select]
was selected. Press the joystick again to remove the checkmark.
• Repeat this step to select all the clips you wish to convert. The total
number of selected clips will appear at the bottom of the screen, next to the " icon.
3 After selecting all the desired clips, press the MENU button.
• The estimated total size of the converted SD movies and the available space on the destination card will be
displayed on the screen.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the clip selection screen.
• The selected clips will be played back as they are converted. While the clips are being converted, you can
press the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Converting All Clips to Standard Definition
Y
P
O
1 From the index screen of the source card, open the [Clips Convert
HD`SD All] screen.
[w Other Functions] > [Clips] > [Convert HD`SD] > [All]
• The estimated total size of the converted SD movies and the available
space on the destination card will be displayed on the screen.
C
[w Other Functions]
[Clips]
[Convert HD`SD]
2 Select [OK] and then press the joystick.
[All]
• All of the clips on the source card will be converted to SD movies on
the destination card.
• Select [Cancel] instead to cancel the operation.
• The clips will be played back as they are converted. While the clips are being converted, you can press the
joystick to cancel.
3 When the confirmation message appears, press the joystick.
NOTES
The maximum total playback time of the clips to be converted to standard definition is 12 hours.
The bit rate of converted SD movies is 9 Mbps.
Clips recorded with the 24P frame rate cannot be converted to standard definition.
Clips are played back as they are converted to standard definition. If you set an assignable button to
[Headphone +], [Headphone -], [Speaker +] or [Speaker -] (A 85), you can press the button to adjust the
headphone volume or built-in speaker during the conversion.
• Clips cannot be converted to standard definition when the SD card already contains the maximum number of
folders or clips (A 141).
•
•
•
•
109
Clip Operations
Deleting SD Movies
From the [SD Movies] index screen you can delete clips that were converted to standard definition.
110
Deleting a Single SD Movie
1 Open the [SD Movies] index screen (A 102).
2 Select the desired SD movie and then press the joystick to open the clip menu.
3 Select [Delete Clip] and then press the joystick.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the SD movie is being deleted, the operation cannot be canceled.
5 When the confirmation message appears, press the joystick.
Deleting All SD Movies
[w Other Functions]
1 Open the [SD Movies] index screen (A 102).
2 Open the [Clips Delete All] screen.
[w Other Functions] > [Clips] > [Delete] > [All]
[Clips]
3 Select [OK] and then press the joystick.
• All the SD movies will be deleted.
• Select [Cancel] instead to cancel the operation.
• While the SD movies are being deleted, you can press the joystick to
cancel.
C
Y
P
O
4 When the confirmation message appears, press the joystick.
[Delete]
[All]
6
External Connections
111
Video Output Configuration
The video signal output from the HDMI OUT terminal depends on the various menu settings and the capabilities
of the external monitor. Video from the AV OUT terminal is output as 480/59.94i (59.94 Hz recordings) or 576/
50.00i (50.00 Hz recordings). If necessary, you can superimpose the onscreen displays on the video displayed
on the external monitor (A 114).
Operating modes:
Video Output Configuration by Terminal
[System Frequency]
set to [59.94 Hz]
[System Frequency]
set to [50.00 Hz]
HD Output*
1080/59.94i
1080/50.00i
SD Output
480/59.94P
576/50.00P
SD Output
480/59.94i
576/50.00i
Terminal
HDMI OUT
AV OUT
Y
P
O
* You can use the [£ LCD/VF Setup] > [Zebra HD Output] setting to display the zebra patterns on an external monitor (HD
output only).
C
Connecting to an External Monitor
Connecting to an External Monitor
112
When you connect the camcorder to an external monitor for recording or playback, use the terminal on the
camcorder that matches the one you wish to use on the monitor. Then, select the video signal output
configuration (A 111).
Operating modes:
Connection Diagram
We recommend that you power the camcorder from a household power outlet using the compact power adapter.
AV OUT
terminal
HDMI OUT
terminal
C
STV-250N
Stereo Video
Cable (optional)
Y
P
O
HDMI cable
(commercially
available)
HDMI IN
VIDEO IN/
AUDIO IN
Using the HDMI OUT Terminal
The HDMITM OUT terminal offers a digital connection and outputs both a video and audio signal. The output
signal will automatically switch to HD or SD depending on the capability of the external monitor. Audio will be
output as a 2ch linear PCM (16 bits, 48 kHz) signal.
NOTES
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
(A 114).
• You can select the SD output method (A 113).
• The HDMI OUT terminal on the camcorder is for output only. Do not connect it to an HDMI output terminal on
an external device, as this may damage the camcorder.
• There will be no video output from the AV OUT terminal while an external monitor is connected to the HDMI
OUT terminal.
• Correct operation cannot be guaranteed when connecting the camcorder to DVI monitors.
• Video may not be output correctly depending on the monitor. In such case, use the AV OUT terminal.
Connecting to an External Monitor
Using the AV OUT Terminal
The AV OUT terminal outputs a down-converted analog video signal and audio signal for connection to monitors
with a composite audio/video input.
NOTES
• When you play back a clip on a monitor with a 4:3 aspect ratio, the monitor will switch automatically to
widescreen mode if it is compatible with the Video ID-1 or WSS system.
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
(A 114).
SD Output
[¢ Video Setup]
When HD video (16:9 aspect ratio) is converted and output as SD video
(4:3 aspect ratio), you can choose how it appears on the external monitor.
Operating modes:
[Resize SD Output]
[Squeeze]
1 Open the [Resize SD Output] submenu.
[¢ Video Setup] > [Resize SD Output]
Y
P
O
2 Select the desired option and then press the joystick.
Options
[Letterbox]:
[Squeeze]:
[Side Crop]:
C
The 16:9 aspect ratio is maintained but black letterbox bars are added to the top and bottom of the
image.
The image is squeezed from the left and right so that the entire image fits within the screen. The image
will appear normal if the external monitor also has a 16:9 aspect ratio.
The left and right sides of the image are cropped so that the central part of the image fits within the
screen.
Original image (16:9)
[Letterbox] setting
[Squeeze] setting
[Side Crop] setting
NOTES
• The [Resize SD Output] setting applies also to the reviewing of the last clip recorded (A 82).
• In
mode, the [Squeeze] setting is applied and cannot be changed.
113
Connecting to an External Monitor
Superimposing Onscreen Displays to Appear on an
External Monitor
114
By default, onscreen displays are shown on the viewfinder but you can
choose to superimpose onscreen displays on video output from the HDMI
OUT terminal or AV OUT terminal. Doing so will display the onscreen
displays on an external monitor. You must set this function separately for
HD and SD output. This setting will not affect your recordings.
Operating modes:
[¢ Video Setup]
[Character Display]
[VF]
[¢ Video Setup]
In
mode, you need to select where the onscreen displays will be
output. Perform all the procedure from the beginning. In
mode,
onscreen displays will automatically disappear from the viewfinder’s
screen when video is being output from one of the terminals, so steps 1
and 2 are not necessary. Start the procedure from step 3.
[HD Onscreen Disp.]
[SD Onscreen Disp.]
[Off]
1 Open the [Character Display] submenu.
[¢ Video Setup] > [Character Display]
2 Select [Ext. Out] and then press the joystick.
3 Open the [HD Onscreen Disp.] or [SD Onscreen Disp.] submenu.
[¢ Video Setup] > [HD Onscreen Disp.] or [SD Onscreen Disp.]
4 Select [On] and then press the joystick.
Y
P
O
• T appears on the upper right of the screen (when [£ LCD/VF Setup] > [Custom Display 2] >
[Output Display] is set to [On]).
C
NOTES
• Onscreen displays cannot appear simultaneously on the viewfinder and on an external monitor connected to
one of the video output terminals.
• During SD video output, onscreen displays will not appear on an external monitor if [¢ Video Setup] >
[Resize SD Output] is set to [Side Crop].
• If you set an assignable button to [Onscreen Display] (A 85), you can press the button to turn on and off the
superimposing of onscreen displays on video output from the camcorder’s terminals (simultaneously for HD
and SD video).
Audio Output
Audio Output
The camcorder can output audio from the HDMI OUT terminal, AV OUT terminal or × (headphone) terminal.
When audio is output from the AV OUT terminal or × (headphone) terminal, you can configure other settings,
such as the output channel.
Synchronizing the Video with the Audio being Monitored
When audio is output from the AV terminal or × (headphone) terminal,
you can choose to synchronize the audio signal with the video signal or
have the camcorder output the audio in real time. When the audio is
output in real time, there will be a slight delay. Regardless of the setting,
however, the audio and video signals recorded will be synchronized.
Operating modes:
[¡ Audio Setup]
[Audio Output]
[Monitor Delay]
[Normal]
1 Open the [Monitor Delay] submenu.
[¡ Audio Setup] > [Audio Output] > [Monitor Delay]
2 Select the desired option and then press the joystick.
Options
[Line Out]:
[Normal]:
Y
P
O
Synchronizes the audio and video signals.
Allows you to monitor the audio in real time.
C
Selecting the Audio Channel
You can select the audio channel that is output from the AV OUT terminal
or × (headphone) terminal.
[¡ Audio Setup]
[Audio Output]
Operating modes:
[Channel]
1 Open the [Channel] submenu.
[¡ Audio Setup] > [Audio Output] > [Channel]
[CH1/CH2]
2 Select the desired option and then press the joystick.
Options
[CH1/CH2]:
[CH1/CH1]:
[CH2/CH2]:
[All/All]:
Audio from CH1 is output from the left audio channel and audio from CH2 is output from the right audio
channel.
Audio from CH1 is output from both the left and right audio channels.
Audio from CH2 is output from both the left and right audio channels.
Audio from CH1 and CH2 is mixed and output from both the left and right audio channels.
NOTES
• If you set an assignable button to [Audio Output CH] (A 85), you can press the button to change the audio
channel directly.
115
Audio Output
Selecting the Output Level of the AV OUT Terminal
You can select the output level of audio that is output from the AV OUT
terminal.
116
[¡ Audio Setup]
[Audio Output]
Operating modes:
[Level]
1 Open the audio ouput [Level] submenu.
[1 Vrms]
[¡ Audio Setup] > [Audio Output] > [Level]
2 Select the desired level and then press the joystick.
Options
[1 Vrms]:
The audio output level is normal.
[2 Vrms]:
The audio output level is 6 dB higher.
NOTES
• This setting does not affect audio output to headphones.
C
Y
P
O
Saving Clips to a Computer
Saving Clips to a Computer
Using the supplied software Data Import Utility to save your clips, you have the additional advantage of
automatically joining clips that were saved as multiple files so you can work with them as single clips with the
editing software of your choice.
Operating modes:
Saving Clips Using Data Import Utility:
• Save clips to the computer (all clips/new clips only).
• Join relay clips (A 41) that were saved on separate SD cards and save them as a single clip.
• Join multiple video stream files of a single clip split because of the 2 GB maximum file size restriction and save
them as a single clip.
For more details, check the Data Import Utility Software Guide, a PDF file* in the [\Manual\English] folder of the
supplied PIXELA CD-ROM.
* Adobe® Reader® 6 or later is required to view the PDF file.
Installing the Software
See Installation and System requirements in the Data Import Utility Software Guide (PDF file) for step-by-step
installation instructions and full system requirements. Below are the main system requirements.
OS
Windows XP1, SP3
Windows Vista2, SP2
Windows 72, SP1
CPU
Intel® Core or equivalent
C
RAM
Mac OS X 10.6 or 10.7
Intel® CPU
(not compatible with Power PC)
1 GB (2 GB for Windows 7, 64-bit version)
Display
1
2
Y
P
O
1024 x 768 pixels
32-bit version only.
32-bit and 64-bit versions.
Connection Diagram
We recommend that you power the camcorder from a household power outlet using the compact power adapter.
USB terminal
(mini-B)
USB terminal
(standard-A)
IFC-400PCU USB Cable
(optional)
117
Saving Clips to a Computer
118
C
Y
P
O
7
Photos
119
Taking Photos
You can take photos when the camcorder is in
mode or you can capture a photo from a clip when the
camcorder is in
mode. The size of the photos recorded on the SD card is 1920 x 1080*.
* At this size, the camcorder can save approximately 670 photos on a 1 GB SD card.
Taking Photos in CAMERA Mode
You can take a photo while the camcorder is recording a clip or is in record pause mode. If a custom picture file
is selected in advance, it will be recorded with the photo (A 88). To take a photo, set an assignable button to
[Photo] in advance.
Operating modes:
1 Set an assignable button to [Photo] (A 85).
2 Press the assignable button to take a photo.
Y
P
O
• The icon of the selected SD card (2 or 3) and the number of available photos appear momentarily on the
upper right of the screen.
• If a custom picture file is selected, it will be recorded with the photo.
• The SD card access indicator will illuminate in red as the photo is being recorded.
C
Capturing Photos in MEDIA Mode
You can capture a photo from a clip during playback pause. To capture a photo, set an assignable button to
[Photo] in advance.
Operating modes:
1 Set an assignable button to [Photo] (A 85).
2 Select the desired clip and press the Ò button to start playback.
3 Pause the playback at the point you want to capture.
4 Press the assignable button to capture a photo.
• The screen will momentarily turn black as if a camera shutter had released.
• The icon of the selected SD card (2 or 3) and the number of available photos appear momentarily on the
upper right of the screen.
• The SD card access indicator will illuminate in red as the photo is being recorded.
5 Press the Ñ button to stop playback.
IMPORTANT
• Observe the following precautions while either of the SD card access indicators is illuminated in red. Failure to
do so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
Taking Photos
120
NOTES
• If the LOCK switch on the SD card selected for recording is set to prevent writing, you will not be able to
record a photo. Change the position of the LOCK switch in advance.
• Even if [w Other Functions] > [Custom Function] > [Scan Reverse Rec] (A 98) is set to a setting other
than [Off], photos will not be inverted.
C
Y
P
O
Photo Playback
Photo Playback
You can view the photos that you took with the camcorder.
121
Operating modes:
Displaying the [Photos] Index Screen
Display the [Photos] index screen to view photos.
1 Set the Q switch to MEDIA.
• The camcorder switches to
screen appears.
mode and the clip index
2 Press the INDEX button.
• The index screen selection menu appears.
3 Select [Photos] and then press the joystick.
• The [Photos] index screen appears.
• After you are finished viewing photos, press the INDEX button to
return to the clip index screen.
Viewing Photos
C
Y
P
O
1 Move the orange selection frame to the desired photo.
2 Press the Ò button to view the photo.
• The photo playback screen appears and the selected photo is displayed.
• Use the Ú/Ù buttons or push the joystick left/right to switch to the
previous/next photo.
• Press the DISP. button to hide/show the onscreen displays.
• Press the Ñ button to return to the [Photos] index screen.
IMPORTANT
• Observe the following precautions while either of the SD card access
indicators is illuminated in red. Failure to do so may result in permanent data
loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD
cards.
NOTES
• The following photos may not be displayed correctly.
- Photos not recorded with this camcorder.
- Photos created or edited on a computer.
- Photos whose file names have been changed.
Photo Operations
Photo Operations
You can use the photo menu to copy a photo, delete a photo, or copy a custom picture file embedded in a
photo. You can display the photo menu from the [Photos] index screen or photo playback screen.
122
Using the Photo Menu
1 From the [Photos] index screen, select a photo and then press the joystick.
• If you are viewing a photo, simply press the joystick.
• The photo menu appears. Available functions depend on the photo’s settings.
2 Select the desired function and then press the joystick.
Copying Photos
You can copy photos from one SD card to the other.
Operating modes:
Copying a Photo from the Playback Screen
1 Display the photo to be copied (A 121).
2 Press the joystick to open the photo menu.
3 Select [Copy] and then press the joystick.
C
Y
P
O
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The selected photo is copied.
5 When the confirmation message appears, press the joystick.
Copying a Photo from the Index Screen
1 Open the [Photos] index screen (A 121).
2 Move the orange selection frame to the photo to be copied.
3 Press the joystick to open the photo menu.
4 Select [Copy] and then press the joystick.
5 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The selected photo is copied.
6 When the confirmation message appears, press the joystick.
Photo Operations
Copying a Selection of Photos
[w Other Functions]
1 From the [Photos] index screen open the photo selection screen.
[w Other Functions] > [Photos] > [Copy] > [Select]
2 Using the joystick, bring the orange selection frame to a photo you wish
to copy and then press the joystick.
• A checkmark " will appear next to the photo's thumbnail to indicate
it was selected. Press the joystick again to remove the checkmark.
• Repeat this step to select all the photos you wish to copy. The total
number of selected photos will appear at the bottom of the screen,
next to the " icon.
[Photos]
[Copy]
[Select]
3 After selecting all the desired photos, press the MENU button.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the photo selection screen.
• While the photos are being copied, you can press the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Copying All Photos
[w Other Functions]
1 From the [Photos] index screen open the [Photos Copy All] screen.
[w Other Functions] > [Photos] > [Copy] > [All]
Y
P
O
2 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the photos are being copied, you can press the joystick to
cancel.
C
[Photos]
[Copy]
[All]
3 When the confirmation message appears, press the joystick.
Deleting Photos
You can delete a photo you no longer need. When you do so, however, the custom picture file embedded in it
will also be deleted. Photos can be deleted one at a time from the photo playback screen or [Photos] index
screen.
Operating modes:
Deleting a Photo from the Playback Screen
1 Display the photo to be deleted (A 121).
2 Press the joystick to open the photo menu.
3 Select [Delete] and then press the joystick.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The selected photo is deleted and the next photo is displayed.
• If a custom picture file is embedded in the photo, it is also deleted.
5 When the confirmation message appears, press the joystick.
123
Photo Operations
Deleting a Photo from the Index Screen
1 Open the [Photos] Index Screen (A 121).
2 Move the orange selection frame to the photo to be deleted.
124
3 Press the joystick to open the photo menu.
4 Select [Delete] and then press the joystick.
5 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The selected photo is deleted.
• If a custom picture file is embedded in the photo, it is also deleted.
6 When the confirmation message appears, press the joystick.
Deleting a Selection of Photos
[w Other Functions]
1 From the [Photos] index screen open the photo selection screen.
[w Other Functions] > [Photos] > [Delete] > [Select]
[Photos]
2 Using the joystick, bring the orange selection frame to a photo you wish
to delete and then press the joystick.
• A checkmark " will appear next to the photo's thumbnail to indicate
it was selected. Press the joystick again to remove the checkmark.
• Repeat this step to select all the photos you wish to delete. The total
number of selected photos will appear at the bottom of the screen,
next to the " icon.
[Delete]
[Select]
Y
P
O
3 After selecting all the desired photos, press the MENU button.
C
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the photo selection screen.
• While the photos are being deleted, you can press the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Deleting All Photos
[w Other Functions]
1 From the [Photos] index screen open the [Photos Delete All] screen.
[w Other Functions] > [Photos] > [Delete] > [All]
2 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the photos are being deleted, you can press the joystick to
cancel.
3 When the confirmation message appears, press the joystick.
IMPORTANT
• Be careful when deleting photos. Deleted photos cannot be recovered.
• Photos that were protected using other devices cannot be deleted with the camcorder.
[Photos]
[Delete]
[All]
Photo Operations
Copying Custom Picture Files
You can copy to the camcorder a custom picture file embedded in a photo. Custom picture files can be copied
from the photo playback screen or [Photos] index screen.
125
Operating modes:
Copying a File from the Playback Screen
1 Display the photo with the custom picture file to be copied (A 121).
2 Press the joystick to open the photo menu.
3 Select [Copy / File] and then press the joystick.
• The [/ Data 1/3] screen appears with a file slot in the camcorder highlighted in orange.
• Alternatively, you can press the CUSTOM PICTURE button.
• You can push the joystick up/down to display the [/ Data 2/3] and [/ Data 3/3] screens.
4 Push the joystick left/right to select the desired file slot and then press the joystick.
5 Select [OK] and then press the joystick.
• The custom picture file embedded in the selected photo is copied, overwriting the file in that slot.
• Select [Cancel] instead to cancel the operation.
6 When the confirmation message appears, press the joystick.
Copying a File from the Index Screen
1 Open the [Photos] Index Screen (A 121).
C
Y
P
O
2 Move the orange selection frame to the photo with the custom picture file to be copied.
3 Press the joystick to open the photo menu.
4 Select [Copy / File] and then press the joystick.
• The [/ Data 1/3] screen appears with the orange selection frame indicating a file slot in the camcorder.
• Alternatively, you can press the CUSTOM PICTURE button.
• You can push the joystick up/down to display the [/ Data 2/3] and [/ Data 3/3] screens.
5 Push the joystick left/right to select the desired file slot and then press the joystick.
6 Select [OK] and then press the joystick.
• The custom picture file embedded in the selected photo is copied, overwriting the file in that slot.
• Select [Cancel] instead to cancel the operation.
7 When the confirmation message appears, press the joystick.
NOTES
• You cannot copy the custom picture file to a file slot with a protected file.
• By default, file slots [C7] to [C9] are protected.
Photo Operations
126
C
Y
P
O
8
Additional Information
127
Menu Options
For details about how to select an item, refer to Using the Menus (A 27). For details about each function, see
the reference page. Menu items without a reference page are explained after the tables. Setting options in
boldface indicate default values. Menu items not available appear grayed out.
To skip directly to the page of a specific menu:
[~ Camera Setup] menu
[¡ Audio Setup] menu
[¢ Video Setup] menu
[£ LCD/VF Setup] menu
[¤ TC/UB Setup] menu
[w Other Functions] menu
[ My Menu] customized menu
[~ Camera Setup] menu (
Menu item
A 127
A 128
A 128
A 129
A 132
A 132
A 134
mode only)
Submenu
Setting options
Y
P
O
A
[Light Metering]
[Backlight], [Standard], [Spotlight]
61
[AE Shift]
[+2.0], [+1.5], [+1.25], [+1.0], [+0.75], [+0.5], [+0.25], [±0], [-0.25],
[-0.5], [-0.75], [-1.0], [-1.25], [-1.5], [-2.0]
60
[ISO/Gain]
[Select]
[ISO Increment]
[Gain]
[Iris]
[Shutter]
C
[ISO], [Gain]
[1 stop], [1/3 stop]
56
[Normal], [Fine]
[Iris Increment]
[1/2 stop], [1/3 stop], [Fine]
[Zoom-Iris Correct.]
[On], [Off]
[Mode]
[Speed], [Angle], [Clear Scan], [Slow], [Off]
[Shutter Increment]
[1/3 stop], [1/4 stop]
59
53
[Flicker Reduction]
[Automatic], [Off]
55
[/ CINEMA Locked]
[On], [Off]
49
[EF-S Lens]
[On], [Off]
30
[ABB]
[Cancel], [OK]
43
[Color Bars]
[Periph. Illum. Corr.]
[Enable]
[On], [Off]
[Type]
When [System Frequency] is set to [59.94 Hz]:
[SMPTE], [ARIB]
When [System Frequency] is set to [50.00 Hz]:
[EBU], [SMPTE]
[On], [Off]
79
30
Menu Options
[¡ Audio Setup] menu
Menu item
[Audio Input]
128
Submenu
[Off], [LC1], [LC2]
Ü
–
75
[Int. Mic Sensitivity]
[Normal], [High]
Ü
–
75
[MIC/Int. Mic Att.]
[On], [Off]
Ü
–
75
[MIC Mode]
[Automatic], [Manual]
Ü
–
[MIC Level]
0 to 99 (50)
Ü
–
[XLR Rec Channel]
[CH1], [CH1/CH2]
Ü
–
76
[XLR1 Mic Trimming]
[+12 dB], [+6 dB], [0 dB], [-6 dB], [-12 dB]
Ü
–
78
Ü
–
78
Ü
–
77
Ü
–
74,
77
[XLR2 Mic Trimming]
[XLR1 Mic Att.]
[On], [Off]
[XLR2 Mic Att.]
[Audio Output]*
A
Setting options
[Int. Mic Low Cut]
74
[XLR ALC Link]
[Linked], [Separated]
[Limiter]
[On], [Off]
[1 kHz Tone]
[-12 dB], [-18 dB], [-20 dB], [Off]
Ü
–
79
[Monitor Delay]
[Line Out], [Normal]
Ü
–
115
[Channel]
[CH1/CH2], [CH1/CH1], [CH2/CH2], [All/All]
Ü
Ü
115
[Level]
[1 Vrms], [2 Vrms]
Ü
Ü
116
[Headphone Volume]
[Off], 1 to 15 (8)
Ü
Ü
78,
104
[Speaker Volume]
[Off], 1 to 15 (8)
–
Ü
104
* Not available in the [Photos] index screen.
[¢ Video Setup] menu
Menu item
C
Y
P
O
A
Setting options
[Character Display]
[VF], [Ext. Out]
Ü
–
[HD Onscreen Disp.]
[On], [Off]
Ü
Ü
[SD Onscreen Disp.]
[On], [Off]
Ü
Ü
[Resize SD Output]
[Letterbox], [Squeeze], [Side Crop]
–
Ü
114
113
Menu Options
[£ LCD/VF Setup] menu
Menu item
[LCD Setup]
[VF Setup]
Submenu
A
Setting options
[Brightness]
-99 to 99 (±0)
Ü
Ü
[Contrast]
-99 to 99 (±0)
Ü
Ü
[Color]
-20 to 20 (±0)
Ü
Ü
[Sharpness]
1 to 4 (2)
Ü
Ü
[Backlight]
[Normal], [Bright]
Ü
Ü
[Brightness]
-99 to 99 (±0)
Ü
Ü
[Contrast]
-99 to 99 (±0)
Ü
Ü
[Color]
-20 to 20 (±0)
Ü
Ü
[Sharpness]
1 to 4 (2)
Ü
Ü
[Backlight]
129
33
33
[Normal], [Bright]
Ü
Ü
[LCD/VF B&W]
[On], [Off]
Ü
Ü
33
[LCD/VF Simul.]
[On], [Off]
Ü
Ü
33
[View Assist.]
[On], [Off]
Ü
–
97
[Peaking]
[On], [Off]
Ü
–
[Peaking 1], [Peaking 2]
Ü
–
[Color]
[White], [Red], [Yellow], [Blue]
Ü
–
[Gain]
[Off], 1 to 15 (8)
Ü
–
[Frequency]
1 to 4 (2)
Ü
–
[Color]
[White], [Red], [Yellow], [Blue]
Ü
–
[Gain]
[Off], 1 to 15 (15)
Ü
–
1 to 4 (1)
Ü
–
[On], [Off]
Ü
–
[Zebra 1], [Zebra 2], [Zebra 1&2]
Ü
–
[Zebra 1 Level]
[70 ±5%], [75 ±5%], [80 ±5%], [85 ±5%],
[90 ±5%], [95 ±5%]
Ü
–
[Zebra 2 Level]
[70%], [75%], [80%], [85%], [90%], [95%],
[100%]
Ü
–
[Select]
[Peaking 1]
[Peaking 2]
[Frequency]
[Zebra]
[Select]
[On], [Off]
Ü
–
[Enable]
[On], [Off]
Ü
–
[Center]
[White], [Gray], [Off]
Ü
–
[Horizontal]
[White], [Gray], [Off]
Ü
–
[Grid]
[White], [Gray], [Off]
Ü
–
[Safety Zone]
[White], [Gray], [Off]
Ü
–
[Safety Zone Area]
[80%], [90%], [92.5%], [95%]
Ü
–
[Aspect Marker]
[White], [Gray], [Off]
Ü
–
[Aspect Ratio]
[4:3], [13:9], [14:9], [1.66:1], [1.75:1],
[1.85:1], [2.35:1]
Ü
–
[On], [Off]
–
[Zebra HD Output]
[Markers]
[Audio Level]
C
Y
P
O
Ü*
66
68
67
–
Menu Options
Menu item
[Custom Display 1]
130
[Custom Display 2]
Submenu
A
Setting options
[Light Metering]
[On], [Off]
Ü
–
[Custom Picture]
[On], [Off]
Ü
–
[Focal Length]
[On], [Off]
Ü
–
[ND Filter]
[On], [Off]
Ü
–
[AF Mode]
[On], [Off]
Ü
–
[Key Lock]
[On], [Off]
Ü
–
[White Balance]
[On], [Off]
Ü
–
[Exposure]
[On], [Off]
Ü
–
[Iris]
[On], [Off]
Ü
–
[ISO/Gain]
[On], [Off]
Ü
–
[Shutter]
[On], [Off]
Ü
–
[Peaking]
[On], [Off]
Ü
–
[Magnification]
[On], [Off]
Ü
–
[View Assist.]
[On], [Off]
Ü
–
[EF-S Lens]
[On], [Off]
Ü
–
[Lens]
[On], [Off]
Ü
–
[Remaining Battery]
[Warning], [Normal], [Off]
Ü
–
[Remaining Rec Time]
[Warning], [Normal], [Off]
Ü
–
[Rec Mode]
[On], [Off]
Ü
–
[Time Code]
[On], [Off]
Ü
–
[Photo]
[Warning], [Normal], [Off]
Ü
–
[Bit Rate]
[On], [Off]
Ü
–
[Frame Rate]
[On], [Off]
Ü
–
[Character Rec]
[On], [Off]
Ü
–
[Output Display]
[On], [Off]
Ü
–
[User Bit]
[On], [Off]
Ü
–
[Audio Output CH]
[On], [Off]
Ü
–
[Audio Level]
[On], [Off]
Ü
–
[HDMI Rec Command]
[On], [Off]
Ü
–
[Temperature/Fan]
[On], [Off]
Ü
–
[Date/Time]
[Date/Time], [Time], [Date], [Off]
Ü
–
–
Ü*
[Date/Time]
C
Y
P
O
[On], [Off]
–
–
–
* Not available in the [Photos] index screen.
[Audio Level]: Displays the audio level meter when set to [On].
[Custom Display 1] settings
[Light Metering]: When set to [On], the light metering icon (° or ®) is displayed if [~ Camera Setup] >
[Light Metering] is set to [Backlight] or [Spotlight].
[Custom Picture]: Displays the custom picture icon (/) when set to [On], indicating that a custom picture file
was selected and its custom picture settings will be applied.
[Focal Length]: Displays the current focal length of an attached EF lens when set to [On].
[ND Filter]: Displays the ND filter indicator when set to [On].
[AF Mode]: When set to [On], displays the autofocus icon (AF) if the focus mode switch on the attached EF lens
is set to AF.
[Key Lock]: Displays the key lock icon (C) when set to [On].
Menu Options
[White Balance]: Displays the white balance indicator when set to [On].
[Exposure]: Displays the exposure bar when set to [On].
[Iris]: Displays the aperture setting when set to [On].
131
[ISO/Gain]: Displays the ISO speed or gain setting when set to [On].
[Shutter]: Displays the shutter speed setting when set to [On].
[Peaking]: Displays the peaking icon (J or K) when set to [On].
[Magnification]: Displays the screen magnification icon (^) when set to [On], indicating that the image on
the screen is being magnified.
[View Assist.]: Displays the view assistance icon (
) when set to [On].
[EF-S Lens]: Displays the EF-S lens correction icon
[Lens]: Displays the lens warning icon
when set to [On].
when set to [On].
[Custom Display 2] settings
[Remaining Battery]: Controls when the remaining battery indicator appears.
[Normal]: Always appears on the screen.
[Warning]: Appears only when there is a warning.
[Remaining Rec Time]: Displays the remaining recording time.
[Normal]: Always appears on the screen.
[Warning]: Appears only when there is a warning.
Y
P
O
[Rec Mode]: Displays the recording operation indicator ([STBY] in record pause mode, for example) when set
to [On].
[Time Code]: Displays the time code when set to [On].
C
[Photo]: Controls the display of the SD card status indicator and remaining number of photos when taking a
photo.
[Normal]: Always appears on the screen.
[Warning]: Appears only when there is a warning.
[Bit rate]: Displays the bit rate when set to [On].
[Frame Rate]: Displays the frame rate when set to [On].
[Character Rec]: Displays the character recording warning icon (S) when set to [On], indicating that the
onscreen displays will be recorded on the clip.
[Output Display]: Displays the output display warning icon (T) when set to [On], indicating that the
onscreen displays will be output to an external monitor.
[User Bit]: Displays the user bit when set to [On].
[Audio Output CH]: Displays the audio output channel when set to [On].
[Audio Level]: Displays the audio level indicator and, if activated, the audio peak limiter icon (
) when set to [On].
[HDMI Rec Command]: Displays the status of the HDMI recording command that is being output when
[w Other Functions] > [HDMI] > [Rec Command] is set to [On].
[Temperature/Fan]: Displays the cooling system warning icons (
and/or
[Date/Time]: Displays the date and/or the time while recording.
[Date/Time]: Displays the date and time of recording during playback.
) when set to [On].
Menu Options
[¤ TC/UB Setup] menu (
Menu item
[Time Code]
132
[User Bit]
mode only)
Submenu
A
Setting options
[Mode]
[Preset], [Regen.]
[Run]
[Rec Run], [Free Run]
[DF/NDF]*
[DF], [NDF]
70
[Setting]
[Set], [Reset]
69
[Output Mode]
[Fixed], [Pulldown]
72
[Type]
[Setting], [Time], [Date]
72
69
* In the following cases, the time code is set to [NDF] and this setting cannot be changed:
- [w Other Functions] > [System Frequency] is set to [50.00 Hz]
- [w Other Functions] > [System Frequency] is set to [59.94 Hz] and the frame rate is set to 24P
[w Other Functions] menu
Menu item
[Reset]
[Transfer Menu//]
Submenu
[Cancel], [OK]
Ü
[Camera Settings]
[Cancel], [OK]
Ü
–
[Assignable Buttons]
[Cancel], [OK]
Ü
Ü1
Ü
Ü
[Save To *]
[*A]
[Menu], [Menu+/]
[*B]
[Load From *]
[*A]
[Menu], [Menu+/]
List of world time zones.
[UTC-05:00 New York] or [UTC+01:00
Central Europe]2
Ü
Ü
[Date/Time]
–
Ü
Ü
[Date Format]
[YMD], [YMD/24H], [MDY], [MDY/24H],
[DMY], [DMY/24H]2
Ü
Ü
[Setting]
[WFM], [Edge Mon.], [Off]
Ü
–
–
Ü4
[Line], [Line+Spot], [Field], [RGB], [YPbPr]
Ü
Ü4
[1x], [2x]
Ü
Ü4
[Type 1], [Type 2]
Ü
–
[Off], 1 to 15 (12)
Ü
–
[Deutsch], [English], [Español], [Français],
[Italiano], [Polski], [
], [
],
[
], [
]
Ü
Ü
See footnote 3
Ü
–
–
Ü1
Ü
–
C
Y
P
O
[WFM], [Off]
[Waveform Monitor]
[Gain]
[Edge Monitor]
[Gain]
[Language !]
[Assign Button]
[1] to [15]
[7] to [15]
[Tally Lamp]
[Front]
[On], [Off]
[Rear]
–
99
Ü
[Time Zone]
[WFM (LCD)]
Ü
Ü
[*B]
[Set Clock]
A
Setting options
[All Settings]
25
25
80
80
81
26
85
–
[Media Access LED]
[On], [Off]
Ü
Ü
–
[Fan]
[On], [Automatic]
Ü
–
36
[System Frequency]
[59.94 Hz], [50.00 Hz]2
Ü
Ü1
50
[Relay Rec]
[On], [Off]
Ü
–
41
[Double Slot Rec]
[On], [Off]
Ü
–
41
[Bit Rate]
[24 Mbps LPCM], [24 Mbps], [17 Mbps],
[7 Mbps]
Ü
–
50
Menu Options
Menu item
Submenu
[Frame Rate]
[Pre Rec]
–
83
–
–
Ü4
106
[Delete]
[Select], [All]
–
Ü4
[All]
–
Ü5
[Select], [All]
–
Ü4
108
[Entire Clip], [Last 4 sec]
Ü
–
82
[Time Code]
[On], [Off]
Ü
–
–
[Rec Command]
[On], [Off]
Ü
–
–
[File Numbering]
[Reset], [Continu.]
Ü
–
141
[Add / File]
[On], [Off]
Ü
–
88
[Copy]
[Select], [All]
–
Ü6
122
[Delete]
[Select], [All]
–
Ü6
123
–
Ü
1
141
Ü
–
98
Ü
Ü
–
Ü
Ü
40
[Reset], [Continu.]
[Shockless WB]
[On], [Off]
[AE Response]
[Fast], [Normal], [Slow]
[Grip Ctrl Dial Dir.]
[Reverse], [Normal]
[F. Assist. B&W]
[Both], [Magnify], [Peaking], [Off]
[Magn. Add. Disp.]
[Scan Reverse Rec]
[Character Rec]
[Reset Hour Meter]
[Initialize Media]
[Cancel], [OK]
133
–
[File Numbering]
[Custom Function]
Ü
50
Ü
[Rec Review]
[Photos]
[On], [Off]
–
[Select], [All]
[Convert HD`SD]
[HDMI]
Ü
[Copy]
[Delete Last Clip]
[Clips]
A
Setting options
When [System Frequency] is set to [59.94 Hz]:
[60i], [PF30], [PF24], [24P]
When [System Frequency] is set to [50.00 Hz]:
[50i], [PF25]
C
Y
P
O
[Peaking], [Edge Mon.], [Off]
[Both], [Vertical], [Horizontal], [Off]
[On], [Off]
[Cancel], [OK]
[*A]
107
[Complete], [Quick]
[*B]
[Lens Firmware]
–
Ü
–
31
[Firmware]
–
Ü
–
–
1
2
3
Not available in the [Photos] index screen.
The default value depends on the country/region or purchase.
Setting options for [Assign Button]: [(NONE)], [ONE-SHOT AF], [PUSH AUTO IRIS], [Iris +], [Iris -], [AE Shift +], [AE Shift -],
[Backlight], [Spotlight], [ISO/GAIN], [SHUTTER], [View Assist.], [PEAKING], [ZEBRA], [WFM], [MAGN.], [Color Bars], [Markers],
[LCD Setup], [VF Setup], [LCD/VF B&W], [Onscreen Display], [Time Code], [Time Code Hold], [Headphone +], [Headphone -],
[Speaker +], [Speaker -], [Audio Output CH], [Audio Level], [Photo], [Fan], [My Menu], [Initialize Media], [User Setting (NONE)].
The default settings are as follows. [1] to [6]: [(NONE)], [7] and [8]: [MAGN.], [9]: [PEAKING], [10]: [ZEBRA], [11]: [WFM], [12]:
[PUSH AUTO IRIS], [13]: [ISO/GAIN], [14]: [SHUTTER], [15]: [ONE-SHOT AF]
4 Available in the clip index screen only.
5 Available in the [SD Movies] index screen only.
6 Available in the [Photos] index screen only.
[Reset]: Reset various camcorder settings.
[All Settings]: Resets all the camcorder’s settings to default settings, except for the hour meter.
[Camera Settings]: Resets the white balance, iris, ISO speed, gain, shutter speed, [~ Camera Setup]
settings and custom picture settings to default settings.
[Assignable Buttons]: Resets the assignable buttons to default settings.
[Tally Lamp]: Allows you to set whether the front and rear tally lamps illuminate while the camcorder is recording.
[Media Access LED]: Allows you to set whether the respective SD card access indicator illuminates while the
camcorder is accessing an SD card.
Menu Options
[Delete Last Clip]: Deletes the last clip you recorded. This menu option will not be available if you turned the
camcorder off since recording the last clip.
[HDMI] settings
[Time Code]: Allows you to output the internal camcorder-generated time code through the HDMI OUT
terminal. The setting cannot be changed while the camcorder is connected to an external device using an
HDMI cable (commercially available).
134
[Rec Command]: After selecting to output the time code, this setting allows you to additionally output also the
camcorder’s recording command. When you connect the camcorder to another recording device using the
HDMI OUT terminal, if you start or stop recording with the camcorder, the other device will also start or stop
recording. The setting cannot be changed while the camcorder is connected to an external device using an
HDMI cable (commercially available).
[Reset Hour Meter]: The camcorder has two “hour meters” – the first keeps track of total operation time and the
second keeps track of operation time since the last time the second hour meter was reset with this function.
[Firmware]: You can verify the current version of the camcorder’s firmware. This menu option is usually unavailable.
[
My Menu] (
mode only)
Menu item
[Edit]
Submenu
Setting options
[Register]
[Cancel], [OK]
[Move]
[Cancel], [OK]
[Delete]
[Cancel], [OK]
[Reset All]
[Cancel], [OK]
C
Y
P
O
A
28
Displaying the Status Screens
Displaying the Status Screens
You can use the status screens to check the camcorder’s various recording- and playback-related settings. You
can also output the status screens on an external monitor.
135
Operating modes:
1 Press the STATUS button.
• The status screen most recently displayed will appear unless you
turned off the camcorder or changed the operating mode. In such
case, the [Camera] status screen appears in
mode and the
[Assign Button 1/2] status screen appears in
mode.
2 Push the joystick up/down to scroll through the status screens.
3 When you are finished, press the STATUS button again to exit the
status screens.
• Alternatively, you can press the MENU or CUSTOM PICTURE button.
Doing so will exit the status screen and open the respective menu.
,
Status screen
[Camera]
Y
P
O
A
Description
Displays settings related to recording, such as ISO speed/gain, iris
and shutter speed increments, peripheral illumination correction and
attached lens model information.
Ü
–
136
[Assign Button 1/2],
[Assign Button 2/2]
Allows you to verify the current function of each assignable button.
Ü
Ü
136
[Audio]
Displays settings related to audio.
Ü
Ü1
137
[Media]
Displays information about the SD cards.
Ü
Ü
137
[Video]
Displays the settings for the video terminals and whether the prerecording mode is in effect.
Ü
Ü
138
[Battery/Hour Meter]
Allows you to check the remaining battery time, battery life and how
long the camcorder has been in operation.
Ü
Ü
138
Displays the settings for the custom picture file that is in effect.
Ü
–
139,
140
[/ Data 1/3], [/ Data 2/3],
[/ Data 3/3]2
1
2
C
Does not appear in the [Photos] index screen.
These screens appear only after a custom picture file has been selected.
Displaying the Status Screens
[Camera] Status Screen (
136
mode only)
1
2
3
4
5
6
1
2
3
ISO speed/Gain increment (A 56)
Iris increment (A 59)
Shutter speed increment (A 54)
4
5
6
Correction for peripheral illumination (A 30)
Flicker reduction (A 55)
Lens model name info (A 29)
[Assign Button 1/2], [Assign Button 2/2] Status Screen
1
C
Y
P
O
1
1
Assignable buttons 1 to 15* (A 85)
* Assignable buttons 1 to 6 do not appear in
mode.
Displaying the Status Screens
[Audio] Status Screen
In
mode
137
1
2
3
4
5
6
7
8
In
9
10
11
12
13
mode
8
14
1
2
3
4
5
6
Low-cut filter (built-in microphone) (A 75)
Microphone's sensitivity (built-in microphone)
(A 75)
Microphone attenuator (MIC terminal, built-in
microphone) (A 75)
Microphone mode (MIC terminal) (A 74)
Microphone recording level (MIC terminal) (A 74)
Audio peak limiter (A 74, 77)
C
7
8
9
10
11
12
13
14
Monitor delay (A 115)
Headphone volume (A 104)
Microphone sensitivity (XLR terminal) (A 78)
Microphone attenuator (XLR terminal) (A 78)
Linking recording levels of XLR terminals (A 77)
XLR terminal recording channel (A 76)
Audio reference signal (A 79)
Speaker volume (A 104)
Y
P
O
[Media] Status Screen
In
mode
3
4
5
6
7
1
2
8
1
2
3
4
* In
SD card A
SD card B
SD speed class (A 38)
Total space on the card
5
6
7
8
Used space on the card
Available recording time on the card*
Available number of photos on the card*
Approximate used space on the card
mode, this information appears only when opening the status screen from the clip index screen.
NOTES
• Depending on the card used, the total space displayed on the screen may differ from the nominal capacity
listed on the SD card.
• In
mode and when both relay recording and double slot recording mode are turned off in
mode,
only the information about the SD card currently selected for recording/playback will be displayed.
Displaying the Status Screens
[Video] Status Screen
138
1
2
3
4
1
2
3
*
5
HDMI OUT terminal status
Onscreen displays superimposed on HD video
output (A 114)
SD output setting (A 113)
4
5
Pre-recording mode* (A 83)
Onscreen displays superimposed on SD video
output (A 114)
mode only.
[Battery/Hour Meter] Status Screen
C
1
2
3
Remaining recording time
Remaining recording time indicator
Battery life indicator
Y
P
O
4
5
1
2
3
4
5
Total operation time (A 134)
Operation time since using [Reset Hour Meter]
(A 134)
Displaying the Status Screens
[/ Data 1/3] Status Screen (
mode only)
1
2
3
4
5
6
7
8
1
2
3
4
5
139
9
Custom picture file name (A 88)
Gamma (A 91)
Master pedestal (A 92)
Master black RGB levels (A 92)
Black gamma settings (level, range and point)
(A 92)
6
7
8
9
[/ Data 2/3] Status Screen (
1
2
3
4
5
6
7
1
2
3
Knee settings (slope, point and saturation)
(A 92)
Skin detail settings (hue, chroma, area and Y
level) (A 94)
Selective NR settings (hue, chroma, area and Y
level) (A 94)
Low key saturation (A 92)
Y
P
O
mode only)
C
Sharpness settings (level, horizontal detail
frequency, horizontal/vertical detail balance, and
limit) (A 93)
Sharpness settings (select, knee aperture gain
and slope) (A 93)
Level depend settings (level, slope and offset)
(A 93)
4
5
6
7
Coring settings (level, offset, curve and depth)
(A 93)
Noise reduction (A 94)
Color matrix settings (select, gain and phase)
(A 94)
Color matrix settings (A 94)
Displaying the Status Screens
[/ Data 3/3] Status Screen (
mode only)
1
2
3
4
5
6
140
1
2
3
4
7
8
White balance R/B gain (A 95)
Color correction (A 95)
Area A settings (phase, chroma, area and Y level)
(A 95)
Area A revision settings (level and phase) (A 95)
C
5
6
7
8
Area B settings (phase, chroma, area and Y level)
(A 95)
Area B revision settings (level and phase) (A 95)
Setup level and press (A 95)
Clip at 100% (A 95)
Y
P
O
Resetting the File Numbering
Resetting the File Numbering
mode:
Photos and SD movies are automatically assigned consecutive numbers
from 0101 to 9900, and stored on the SD card in folders containing up to
100 files. Folders are numbered from 101 to 998. You can select the file
numbering method to be used but using the default [Continu.] setting is
recommended.
[w Other Functions]
141
[Photos]
[File Numbering]
Operating modes:
[Continu.]
1 Open the [File Numbering] submenu.
mode: [w Other Functions] > [Photos] > [File Numbering]
mode: [w Other Functions] > [File Numbering]
2 Select the desired option and then press the joystick.
mode:
[w Other Functions]
[File Numbering]
[Continu.]
Options
[Reset]:
[Continu.]:
Y
P
O
File numbers will restart from 101-0101 every time you insert a new SD card. If an SD card already
contains photos or SD movies, file numbers will continue from the number following that of the last photo
or SD movie on the SD card.
File numbers will continue from the number following that of the last photo recorded or SD movie
converted with the camcorder. However, if the SD card you insert already contains photos or SD movies,
file numbers will continue from the number following that of the last photo or SD movie on the SD card.
This setting is the most convenient for managing files on a computer.
C
NOTES
• The file number indicates the name and location of the file on the SD card. For example, the file of a photo
numbered 101-0107 is "IMG_0107.jpg" and it can be found in the "DCIM\101CANON" folder, while the file of
an SD movie numbered 101-0108 is "MVI_0108.mpg"and it is stored in the same folder.
Troubleshooting
Troubleshooting
If you have a problem with your camcorder, refer to this section. Consult your dealer or a Canon Service Center
if the problem persists.
142
Power source
The camcorder will not turn on or it turns off by itself.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Shortly after turning it on, the camcorder turns off on its own.
- You are using a battery pack that is not compatible for use with this camcorder. Use a recommended battery pack
(A 153).
Cannot charge the battery pack.
- The temperature of the battery pack is outside the charging range. If the battery pack’s temperature is below 0 °C
(32 °F), warm it before charging it; if it is above 40 °C (104 °F), let the battery pack cool down before charging it.
- Charge the battery pack in temperatures between 0 °C and 40 °C (32 °F and 104 °F).
- The battery pack is faulty. Replace the battery pack.
The battery pack is exhausted extremely quickly even at normal temperatures.
- Check the [Battery/Hour Meter] status screen (A 138) to see whether the battery pack is at the end of its service life.
If so, buy a new battery pack.
Recording
C
Y
P
O
The camcorder’s controls are not responsive/disabled.
- The grip unit’s plug may not be correctly connected to the camcorder. When attaching the grip unit to the camcorder,
make sure the grip unit’s plug is firmly inserted all the way into the connection terminal on the camcorder (A 35). If
you changed the angle of the grip unit, make sure you did not partially disconnect the plug by mistake.
Pressing the START/STOP button will not start recording.
- The SD card is full or it already contains the maximum number of clips (3,999 clips). Delete some clips (A 107) or
save your clips (A 117) and initialize the SD card (A 40) to free some space. Alternatively, replace the SD card.
- The START/STOP lock lever on the handle unit is set to C, rendering the handle unit's START/STOP button
inoperable. Change the position of the lock lever.
The point where the START/STOP button was pressed does not match the beginning/end of the recording.
- There is a slight interval between pressing the START/STOP button and the actual start/end of recording. This is not a
malfunction.
The camcorder will not focus.
- The viewfinder is not adjusted. Use the dioptric adjustment lever to make the proper adjustment (A 32).
- The lens is dirty. Clean the lens with a soft lens-cleaning cloth.
When a subject flits across in front of the lens, the image appears slightly bent.
- This is a phenomenon typical of CMOS image sensors. When a subject crosses very quickly in front of the camcorder,
the image may seem slightly warped. This is not a malfunction.
Bright red, green or blue dots appear on the screen.
- The camcorder’s CMOS sensor is a delicate piece of precision engineering. Direct exposure of the sensor to ion rays or other
types of cosmic radiation may affect it and this may rarely appear as bright colored dots on the screen. This is the nature of
CMOS image sensors and does not represent a malfunction. Adjusting the black balance (A 43) may help solve the problem.
- The effects of the damage may be more noticeable when the camcorder is used in places subject to high
temperatures, when a high ISO speed or gain level is used and when slow shutter speeds are used.
Abnormal images appear on the screen and the camcorder cannot record properly.
- While recording using an almost empty battery pack together with the compact power adapter, the compact power
adapter was inadvertently disconnected or the power supply was suddenly interrupted. Reconnect the compact
power adapter and turn the camcorder off and then on again or replace the battery pack with a fully charged one.
Changing between recording (ÜREC) and record pause (STBY) takes longer than usual.
- When the SD card contains a large number of clips, some operations may take longer than usual. Save your clips
(A 117) and initialize the SD card (A 40). Alternatively, replace the SD card.
Troubleshooting
The camcorder cannot record to an SD card properly.
- This may occur as recordings are made and deleted over time. Save your clips (A 117) and initialize the SD card (A 40).
After using the camcorder for a long time, it becomes hot.
- The camcorder may become hot after using it continuously for long periods of time; this is not a malfunction. If the
camcorder becomes unusually hot or it becomes hot after using it only for a short while, it may indicate a problem with
the camcorder. Consult a Canon Service Center.
Playback
Cannot delete clips or photos.
- Clips and photos that were protected using other devices cannot be deleted with the camcorder.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
Deleting clips takes longer than usual.
- When the SD card contains a large number of clips, some operations may take longer than usual. Save your clips
(A 117) and initialize the SD card (A 40).
Cannot copy clips.
- There is not enough available space on the SD card being copied to or the SD card already contains the maximum
number of clips (3,999 clips). Delete some clips (A 107) to free some space or replace the SD card.
Cannot select clips or photos.
- You cannot select more than 100 individual clips or photos. Use the [All] option instead of [Select].
Indicators and Onscreen Displays
Y
P
O
ì lights up in red.
- Battery pack is exhausted. Replace or charge the battery pack.
C
í appears on the screen.
- The camcorder cannot communicate with the battery pack attached so the remaining battery time cannot be
displayed.
The tally lamps do not illuminate.
- Set [Other Functions] > [Tally Lamp] > [Front] or [Rear] to [On].
The tally lamps flash quickly.
(4 flashes per second)
- The battery pack is exhausted. Replace or charge the battery pack.
- There is not enough available space on both SD cards. Delete some clips (A 107) to free some space or replace the
SD card.
- A system error has occurred. Turn off the camcorder and back on again. If this does not solve the problem, consult a
Canon Service Center.
The tally lamps flash slowly.
(1 flash per second)
- The combined available space on both SD cards is low. Replace the SD card.
* appears in red on the screen.
- An SD card error occurred. Turn off the camcorder. Remove and reinsert the SD card. Initialize the SD card (A 40) if
the display does not change back to normal.
- The SD card is full. Replace the SD card or delete some clips (A 107) or photos (A 123) to free some space on the
SD card.
Even after stopping recording, the SD card access indicator stays illuminated in red.
- The clip is being recorded. This is not a malfunction.
appears in yellow on the screen.
- The camcorder’s internal temperature has reached a predetermined level. You can continue using the camera.
appears in red on the screen.
- In
mode, when [Other Functions] > [Fan] is set to [Automatic], the cooling fan will start automatically (
appears on the screen).
appears on the screen.
- The camcorder and lens cannot communicate normally. Clean the lens’s contacts and reattach the lens.
143
Troubleshooting
Picture and Sound
144
Screen displays turn on and off repeatedly.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Abnormal characters appear on the screen and the camcorder does not operate properly.
- Disconnect the power source and reconnect it after a short time. If the problem still persists, perform one of the
following actions.
• Disconnect the power source and press the RESET button. This resets all the camcorder’s settings to default values
except for custom picture settings and the hour meter.
• Use the [Other Functions] > [Reset] > [All Settings] function. This resets all the camcorder’s settings to default
values except for the hour meter.
Video noise appears on screen.
- Keep a distance between the camcorder and devices that emit strong electromagnetic fields such as near powerful
magnets and motors, MRI machines or high-voltage power lines.
Horizontal bands appear on the screen.
- This is a phenomenon typical of CMOS image sensors when recording under some types of fluorescent, mercury or
sodium lamps. To reduce the symptoms, Set [Camera Setup] > [Flicker Reduction] to [On] (A 55) or set the shutter
speed to 1/100 (A 53). This is not a malfunction.
No picture appears on the viewfinder.
- No picture will be output to the viewfinder if a cable is connected to the HDMI OUT or AV OUT terminal in playback
mode. Remove the cable.
No onscreen displays appear on the viewfinder.
- In
mode, [¢ Video Setup] > [Character Display] is set to [Ext. Out]. Set it to [VF].
Y
P
O
Audio cannot be recorded.
- The audio input switch is not set correctly (A 73) or the audio recording level is not set correctly (A 74, 77).
- An external microphone connected to the XLR terminal requires phantom power. Set the XLR terminal switch to
MIC+48V (A 76).
C
Audio is recorded at an extremely low level.
- The AUDIO LEVEL switch is set to M, and the recording level is set too low. When using the MIC terminal: [Audio
Setup] > [Audio Input] > [MIC Mode] is set to [Manual] and the [MIC Level] setting is too low. Check the audio level
meter on the screen and adjust the audio level correctly (A 74, 77).
- The microphone attenuator is on. Turn off the microphone attenuator (A 75, 78).
Sound is distorted or is recorded at lower levels.
- When recording near loud sounds (such as fireworks, shows or concerts), sound may become distorted or it may not
be recorded at the actual levels. Activate the microphone attenuator (A 75, 78), or adjust the audio recording level
manually (A 74, 77).
The picture is displayed correctly but there is no sound from the built-in speaker.
- Speaker volume is turned off. Adjust the volume (A 104).
- If headphones are connected to the camcorder, disconnect them.
SD Cards and Accessories
Cannot insert the SD card.
- The SD card you are trying to insert is not facing the correct direction. Turn it over and insert it.
Cannot record on the SD card.
- A compatible SD card must be used (A 38).
- Initialize the SD card (A 40) when you use it with the camcorder for the first time.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
- The SD card is full or it already contains the maximum number of clips (3,999 clips). Delete some clips (A 107) or
photos (A 123) to free some space or replace the SD card.
- The folder and file numbers have reached their maximum value. Set [File Numbering] to [Reset] (A 141) and insert a
new SD card.
Troubleshooting
Recording to and playing back from an SD card is slow.
- This may occur as clips and photos are recorded/deleted over time. Save your recordings (A 117) and initialize the
SD card (A 40).
145
Connections with External Devices
Video noise appears on a nearby TV screen.
- When using the camcorder in a room where a TV is located, keep a distance between the compact power adapter and
the power or antenna cables of the TV.
Playback looks fine on the camcorder but there is no image on the external monitor.
- The camcorder is not connected correctly to the external monitor. Make sure you are using the correct connection
(A 112).
- The video input on the external monitor is not set to the video terminal to which you connected the camcorder. Select
the correct video input.
The camcorder is connected using a commercially available HDMI cable, but there is no picture or sound from the
external monitor.
- Disconnect the HDMI cable and then restore the connection or turn the camcorder off and then on again.
The computer does not recognize the camcorder even though the camcorder is connected correctly.
- Disconnect the USB cable and turn off the camcorder. After a short while, turn it on again and restore the connection.
- Connect the camcorder to a different USB port on the computer.
List of Messages
Y
P
O
Refer to this section if a message appears on the screen. The messages in this section appear in alphabetical
order.
C
Accessing *A/*B Do not remove
- You opened the SD card compartment cover while the camcorder was accessing the SD card. Close the SD card
compartment cover.
CamerabLens communication error. Clean the lens’s contacts and reattach the lens.
- The camcorder cannot correctly communicate with the lens due to dirty lens contacts. After the message disappears,
the
icon appears on the screen. Clean the lens's contacts and reattach the lens.
Cannot acquire battery information
- Battery information can be displayed only for batteries bearing the Intelligent System mark.
Cannot acquire battery information Continue using this battery pack?
- If you are using a battery pack that bears the Intelligent System mark, there may be a problem with the camcorder or
battery pack. Consult a Canon Service Center.
Cannot play back
- The file control information is corrupted or there was a decoder error. Turn off the camcorder and back on again. If this
does not solve the problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. SD cards or clips with corrupt file control information cannot
be read by the supplied software, Data Import Utility.
Cannot record
- The file control information is corrupted or there was an encoder error. Turn off the camcorder and back on again.
Then, remove the SD card being used and reinsert it. Alternatively, replace the SD card. If this does not solve the
problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. SD cards or clips with corrupt file control information cannot
be read by the supplied software, Data Import Utility.
Cannot switch SD card slots
- The SLOT SELECT button was pressed while the camcorder is recording. Wait until recording is finished to change the
selected SD card slot.
Change the battery pack
- The battery pack is exhausted. Replace or charge the battery pack.
Troubleshooting
146
Check *A/*B
- The SD card cannot be accessed. Check that the SD card is inserted correctly and not malfunctioning.
- Due to an SD card error, recording on/playback from the SD card is not possible. Remove and then reinsert the SD
card or use a different SD card.
- You inserted a MultiMedia Card (MMC) into the camcorder. Use a recommended SD card (A 38).
- If after the message disappears, the SD card access indicator illuminates in red, perform the following: Turn off the
camcorder and remove and reinsert the SD card. If the SD card access indicator illuminates in green, you can resume
recording/playback. If the problem persists, save your recordings (A 117) and initialize the SD card (A 40).
Check the data on *A/*B Initializing the card is also recommended
- The SD card cannot be used for any of the following reasons.
• A problem has occurred with the SD card.
• The camcorder cannot read the SD card’s data.
• The SD card was initialized using a computer.
• The SD card has been partitioned.
- Save your clips (A 117) and initialize the SD card (A 40).
Data on *A/*B needs recovering Attempt to recover?
- If data on the SD card is corrupted, such as when the power suddenly turned off while recording, the data must be
recovered. When this message appears, select [OK] and then press the joystick.
Data on *A/*B needs recovering Change the position of the LOCK switch on the memory card.
- This message will appear the next time you turn on the camcorder if power supply was accidentally interrupted while
the camcorder was writing on the SD card and later the position of the SD card's LOCK switch was changed to
prevent erasure. Change the position of the LOCK switch.
Fan error
- The cooling fan has stopped working or may not be working properly. Consult a Canon Service Center.
Y
P
O
File name error
- The folder and file numbers have reached their maximum value. Set [File Numbering] to [Reset] (A 141) and delete all
the photos on the SD card (A 123) or initialize it (A 40).
C
Invalid operation
- The following operations cannot be performed.
• In
mode, immediately reviewing a recording made using pre-recording or double slot recording.
• Pressing the START/STOP button when there is no SD card in the camcorder.
Lens firmware update Firmware update failed. Try updating again.
- The lens's firmware could not be correctly updated. Try updating the lens's firmware again.
Media full
- SD card A and SD card B are full. Delete some clips (A 107) or photos (A 123) to free some space or replace one or
both SD cards.
Media is almost full
- The amount of available space on SD card A and SD card B combined is low. Replace one or both SD cards.
Memory card cover is open
- The SD card compartment cover was open when the camcorder was switched to or turned on in
the compartment cover.
mode. Close
No clips
- There are no clips on the SD card to play back. Clips must be recorded (A 45) in order to play them back.
No photos
- There are no photos on the SD card to play back. Photos must be taken (A 119) in order to view them.
Pre Rec was canceled. Activate Pre Rec again?
- Pre-recording was deactivated automatically after the camcorder was left in record pause mode for about 1 hour with
pre-recording activated. Select [On] and then press the joystick to activate pre-recording again.
Pre Rec will be canceled in a moment.
- The camcorder has been in record pause mode for about 1 hour with pre-recording activated. Pre-recording will be
deactivated automatically in approximately 1 minute.
Recorded at 50.00 Hz/59.94 Hz Check the data on *A/*B Initializing the card is also recommended
- The SD card contains clips that were recorded using a recording type (system frequency) other than the one currently
used by the camcorder. To record on this SD card, save your clips (A 117) and initialize the SD card (A 40). To play
back the recordings on the SD card, set [w Other Functions] > [System Frequency] to [59.94 Hz] or [50.00 Hz] as
necessary, so the camcorder matches the SD card.
Troubleshooting
Temperature too high The fan will be activated
- While [Other Functions] > [Fan] is set to [Automatic], the camcorder's internal temperature has reached a critical level
and the cooling fan will be activated. The fan will turn off automatically once the camcorder's internal temperature has
decreased sufficiently.
This photo cannot be displayed
- You may not be able to display photos taken with other devices or image files created or edited on a computer.
*A/*B Buffer overflow. Recording was stopped.
- The data transfer rate was too high for the SD card in use and the recording was stopped. Use a recommended card
(A 38).
*A/*B Cannot record movies on this memory card
- Video cannot be recorded on a 64 MB or smaller SD card. Use a recommended card (A 38).
*A/*B Cannot restore
- Could not recover data on the SD card. Save your clips (A 117) and initialize the SD card (A 40).
*A/*B May not be possible to record movies on this memory card
- You may not be able to record video on an SD card without a speed class rating or rated SD Speed Class 2. Replace
the SD card with one rated SD speed class 4, 6 or 10.
*A/*B Media full
- SD card A or SD card B is full so recording will not start. Switch to the SD card in the other SD card slot to record.
*A/*B Memory card is write-protected
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
*A/*B Number of clips already at maximum
- The SD card selected for recording already contains the maximum number of clips (3,999 clips). Replace the SD card
or use the SD card in the other SD card slot.
- Because both SD cards reached the maximum number of clips, double slot recording is not available.
• During double slot recording, both “*A” and “*B” will appear in the message.
Y
P
O
*A/*B Reached the recording limit for one clip. Recording was stopped.
- When recording a single clip for an extended period of time, the clip will be split into smaller video files every 2 GB.
This message will appear when the number of smaller video files reaches 50.
C
*A/*B Recording was stopped.
- The file control information is corrupted or there was an encoder error. Turn off the camcorder and back on again.
Then, remove the SD card being used and reinsert it. Alternatively, replace the SD card. If this does not solve the
problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. SD cards or clips with corrupt file control information cannot
be read by the supplied software, Data Import Utility.
*AJ*B / *BJ*A Switched
- This message appears when you use the SLOT SELECT button to switch the SD card slot in use or recording
continued from one SD card to the other.
*AJ*B / *BJ*A Will switch in a moment
- The SD card is almost full so recording will continue on the other SD card in approximately 1 minute.
147
Handling Precautions
Handling Precautions
Camcorder
148
Be sure to observe the following precautions to ensure maximum performance.
• Do not carry the camcorder by the LCD panel. Be careful when closing the LCD panel.
• Do not leave the camcorder in places subject to high temperatures (like the inside of a car parked under direct
sunlight), or high humidity.
• Do not use the camcorder near strong electromagnetic fields such as near powerful magnets and motors, MRI
machines or high-voltage power lines. Using the camcorder in such places may cause anomalies in the video or
audio or video noise to appear.
• Do not use or store the camcorder in dusty or sandy places. The camcorder is not waterproof – avoid also
water, mud or salt. If any of the above should get into the camcorder it may damage the camcorder and/or the
lens. Consult a Canon Service Center as soon as possible.
• Be careful to avoid dust and dirt particles accumulating on the lens or entering the camcorder. When you finish using
the camcorder, make sure to attach the body cap to the lens mount and the lens cap and dust cap to the lens.
• Do not point the lens or viewfinder lens at the sun or other strong light sources. Do not leave the camcorder
pointed at a bright subject. Internal components may become damaged due to concentration of the light by
the lens. Be careful especially when using a tripod or shoulder strap. When you are not using the camcorder or
viewfinder, make sure to attach the lens cap to the lens.
• Be careful of heat generated by lighting equipment.
• Do not disassemble the camcorder. If the camcorder does not function properly, consult qualified service
personnel.
• Do not touch the lens contacts on the lens mount. Dirty contacts may cause a poor
contact between the camcorder and the lens resulting in incorrect operation of the
camcorder. After removing the lens, make sure to attach the body cap to the lens
mount and the lens cap and dust cap to the lens.
• Handle the camcorder with care. Do not subject the camcorder to shocks or vibration
as this may cause damage. When using the shoulder strap, do not allow the
camcorder to swing and hit an object.
C
Y
P
O
Long-term storage
If you do not intend to use the camcorder for a long time, store it in a place free of dust, in low humidity, and at
temperatures not higher than 30 °C (86 °F).
Battery Pack
DANGER!
Treat the battery pack with care.
• Keep it away from fire (or it might explode).
• Do not expose the battery pack to temperature higher than 60 °C (140 °F). Do not leave it near a heater or
inside a car in hot weather.
• Do not try to disassemble or modify it.
• Do not drop it or subject it to shocks.
• Do not get it wet.
• Dirty terminals may cause a poor contact between the battery pack and the camcorder. Wipe the terminals
with a soft cloth.
Handling Precautions
Long-term storage
• Store battery packs in a dry place at temperatures no higher than 30 °C (86 °F).
• To extend the battery life of the battery pack, discharge it completely before storing it.
• Charge and discharge all your battery packs fully at least once a year.
149
Always attach the battery terminal cover.
Do not allow any metal objects to touch the terminals (figure 1), as this can
cause a short circuit and damage the battery pack. Attach the terminal cover
whenever the battery pack is not being used (figure 2).
The battery terminal cover has a [ð]-shaped hole. This is useful when you
wish to differentiate between charged and uncharged battery packs. For
example, with charged battery packs, attach the terminal cover so that the
[ð]-shaped hole shows the colored label.
Back side of the
battery pack
Figure 1
Figure 2
Terminal cover attached
Charged
Uncharged
Y
P
O
Remaining battery time
If the remaining battery time displayed is not correct, charge the battery pack fully. Still, the correct time may not
be displayed if a fully charged battery pack is used continuously in high temperatures or it is left unused for long
periods of time. Also, the correct remaining time may not be displayed, depending on the battery life. Use the
time shown on the screen as an approximation.
C
Regarding the use of non-Canon battery packs
• We recommend using genuine Canon battery packs bearing the Intelligent System
mark.
• If you attach to the camcorder battery packs that are not genuine Canon battery packs, the remaining battery
time will not be displayed.
SD Cards
• We recommend backing up the recordings on the SD cards onto your computer. Data may be corrupted or
lost due to defects or exposure to static electricity. Canon shall not be liable for lost or corrupted data.
• Do not touch or expose the terminals to dust or dirt.
• Do not use SD cards in places subject to strong magnetic fields.
• Do not leave SD cards in places subject to high humidity and high temperature.
• Do not disassemble, bend, drop, or subject SD cards to shocks and do not expose them to water.
• Check the direction before inserting the SD cards. Forcing an SD card into the slot if it is not correctly oriented
may damage the SD card or the camcorder.
• Do not attach any labels or stickers on the SD card.
Handling Precautions
• SD cards have a physical switch to prevent writing on the card so as to avoid the
accidental erasure of the card’s content. To write-protect the SD card, set the
switch to the LOCK position.
150
LOCK switch
Built-in Rechargeable Lithium Battery
The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings. The built-in
lithium battery is recharged while you use the camcorder; however, it will discharge completely if you do not use
the camcorder for about 3 months.
To recharge the built-in lithium battery: Connect the DC cable and compact power adapter to the camcorder
and use a household power outlet to power the camcorder for 24 hours while it is turned off.
Disposal
When you delete data on an SD card, only the file allocation table is altered and stored data is not physically
erased. Take the necessary precautions when you dispose of an SD card, for example by physically damaging it
to prevent the leakage of private data.
If giving an SD card to another person, initialize it using the [Complete] initialization option (A 40). Fill it up with
unimportant recordings, and then initialize it again. This makes recovering the original recordings very difficult.
C
Y
P
O
Maintenance/Others
Maintenance/Others
Cleaning
Camcorder Body
• Use a soft, dry cloth to clean the camcorder body. Never use chemically treated cloths or volatile solvents
such as paint thinner.
Lens
• Remove any dust or dirt particles using a non-aerosol type blower brush.
• Use a clean, soft lens-cleaning cloth to gently wipe the lens using commercially available cleaning fluid for
eyeglasses. Never use tissue paper.
LCD Screen
• Clean the LCD screen using a clean, soft lens-cleaning cloth.
• Condensation may form on the surface of the screen when the temperature changes suddenly. Wipe it with a
soft dry cloth.
Condensation
Moving the camcorder rapidly between hot and cold temperatures may cause condensation (water droplets) to
form on its internal surfaces. Stop using the camcorder if condensation is detected. Continued use may damage
the camcorder.
Y
P
O
Condensation may form in the following cases:
• When the camcorder is moved quickly from cold to warm places
• When the camcorder is left in a humid room
• When a cold room is heated rapidly
C
To avoid condensation
• Do not expose the camcorder to sudden or extreme changes in temperature.
• Remove the SD cards and battery pack. Then, place the camcorder in an airtight plastic bag and let it adjust
gradually to temperature changes before removing it from the bag.
When condensation is detected
The camcorder automatically shuts off.
The precise time required for water droplets to evaporate will vary depending on the location and weather
conditions. As a general rule, wait for 2 hours before resuming use of the camcorder.
Using the Camcorder Abroad
Power Sources
You can use the compact power adapter to operate the camcorder and to charge battery packs in any country
with power supply between 100 and 240 V AC, 50/60 Hz. Consult a Canon Service Center for information on
plug adapters for overseas use.
151
Optional Accessories
Optional Accessories
The following optional accessories are compatible with this camcorder. The availability differs from area to area.
152
BP-950G, BP-955,
BP-970G, BP-975
Battery Pack
CA-930 Compact
Power Adapter
DC-930 DC Cable
CB-920 Car Battery
Adapter
TA-100 Tripod Adapter
SBR-1000 Shooting
Brace
C
STV-250N Stereo Video
Cable
Y
P
O
IFC-400PCU
USB Cable
TB-1 Tripod Adapter
Base
For our customers in the USA: Call or visit your local retailer/dealer for genuine Canon video accessories. You
can also obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040, Canon U.S.A.
Information Center.
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine Canon accessories.
Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the
malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please
note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon
accessories, although you may request such repairs on a chargeable basis.
Optional Accessories
BP-955
BP-975
Battery Packs
When you need extra battery packs, select from the following: BP-950G,
BP-955, BP-970G, BP-975
When you use battery packs bearing the Intelligent System mark, the
camcorder will communicate with the battery and display the remaining
usage time (accurate to 1 minute). You can only use and charge these battery
packs with camcorders and chargers compatible with Intelligent System.
Charging Times
Use the supplied CA-930 Compact Power Adapter to charge battery packs. The charging times given in the
following table are approximate and vary according to charging conditions and initial charge of the battery pack.
BP-950G
BP-955
BP-970G
BP-975
245 min.
200 min.
350 min.
295 min.
Recording and Playback Times
Recording and playback times given in the following tables are approximate and vary according to recording
mode and charging, recording or playback conditions. The effective usage time of the battery pack may
decrease when recording in cold surroundings, when using the brighter screen settings, etc.
EF lenses draw power from the camcorder to operate some functions. Effective usage times may decrease
depending on the lens used.
Approximate times (LCD screen + viewfinder)
System frequency
59.94 Hz
Bit rate
24 Mbps /
24 Mbps LPCM
Usage time
BP-955
BP-970G
BP-975
280 min.
265 min.
390 min.
405 min.
170 min.
160 min.
235 min.
250 min.
425 min.
405 min.
595 min.
635 min.
Recording (maximum)
280 min.
265 min.
390 min.
410 min.
Recording (typical*)
170 min.
160 min.
235 min.
250 min.
Playback
425 min.
405 min.
595 min.
635 min.
Recording (maximum)
280 min.
270 min.
395 min.
415 min.
Recording (typical*)
170 min.
165 min.
240 min.
255 min.
Playback
430 min.
410 min.
600 min.
640 min.
Recording (maximum)
295 min.
285 min.
415 min.
430 min.
Recording (typical*)
180 min.
170 min.
250 min.
265 min.
Playback
430 min.
410 min.
600 min.
640 min.
Recording (maximum)
295 min.
285 min.
420 min.
430 min.
Recording (typical*)
180 min.
170 min.
250 min.
265 min.
Playback
430 min.
410 min.
605 min.
645 min.
Recording (maximum)
300 min.
285 min.
420 min.
450 min.
Recording (typical*)
180 min.
175 min.
255 min.
270 min.
Playback
430 min.
410 min.
610 min.
650 min.
Recording (typical*)
Playback
17 Mbps
7 Mbps
50.00 Hz
24 Mbps /
24 Mbps LPCM
17 Mbps
7 Mbps
Y
P
O
BP-950G
Recording (maximum)
C
153
Optional Accessories
Approximate times using the viewfinder
System frequency
59.94 Hz
154
BP-950G
BP-955
BP-970G
BP-975
24 Mbps /
24 Mbps LPCM
Bit rate
Recording (maximum)
295 min.
280 min.
405 min.
430 min.
Recording (typical*)
180 min.
170 min.
250 min.
265 min.
17 Mbps
Recording (maximum)
295 min.
280 min.
415 min.
430 min.
Recording (typical*)
180 min.
170 min.
250 min.
265 min.
Recording (maximum)
300 min.
285 min.
420 min.
440 min.
Recording (typical*)
180 min.
175 min.
250 min.
270 min.
24 Mbps /
24 Mbps LPCM
Recording (maximum)
320 min.
305 min.
435 min.
470 min.
Recording (typical*)
190 min.
180 min.
260 min.
280 min.
17 Mbps
Recording (maximum)
320 min.
305 min.
435 min.
470 min.
Recording (typical*)
190 min.
180 min.
260 min.
280 min.
Recording (maximum)
325 min.
310 min.
445 min.
475 min.
Recording (typical*)
190 min.
180 min.
265 min.
285 min.
7 Mbps
50.00 Hz
7 Mbps
Usage time
* Approximate times for recording with repeated operations such as start/stop, and power on/off.
CB-920 Car Battery Adapter
Use the car battery adapter to charge battery packs on the go. The car
battery adapter plugs into your car’s cigarette lighter socket and runs off a
12-24V DC negative ground battery.
C
Y
P
O
TA-100 Tripod Adapter
The TA-100 allows you to quickly mount/unmount the camcorder on/from a
tripod.
SBR-1000 Shooting Brace
Using the SBR-1000 for additional support of the camcorder with the neck
strap will significantly lighten the load of the camcoder’s weight while
shooting.
This mark identifies genuine Canon video accessories. When you use Canon video equipment, we
recommend Canon-brand accessories or products bearing the same mark.
Specifications
Specifications
C100
System
155
• Recording System
Movies: AVCHD
Video compression: MPEG-4 AVC/H.264
Audio compression: Linear PCM, 16 bits, 48 kHz, 2ch;
Dolby Digital 2ch
Photos: DCF (Design rule for Camera File system), compatible with Exif Ver. 2.3, JPEG compression
• Video Configuration (recording/playback)
24 Mbps LPCM (VBR), 24 Mbps (VBR), 17 Mbps (VBR):
1920x1080: 60i, 50i, PF30, PF25, PF24, 24P
7 Mbps (VBR):
1440x1080: 60i, 50i, PF30, PF25, PF24, 24P
• Recording Media (not included)
SD, SDHC or SDXC memory card* (2 slots)
* Custom picture files, and camera settings files can be saved on and read from the SD card as well.
• Maximum Recording Time**
16 GB SD Card
24 Mbps LPCM: 85 min., 24 Mbps: 85 min., 17 Mbps : 125 min., 7 Mbps : 285 min.
32 GB SD Card
24 Mbps LPCM: 175 min., 24 Mbps: 175 min., 17 Mbps : 250 min., 7 Mbps : 575 min.
** Approximate figures based on continuous recording.
Y
P
O
• Image Sensor: Super-35mm-equivalent CMOS sensor, approx. 8,290,000 pixels (3840x2160)
C
• LCD screen: 8.8 cm (3.5 in.), wide, color, equivalent to approx. 922,000 dots, 100% coverage
• Viewfinder: 0.61cm (0.24 in.), wide, color, equivalent to approx. 1,555,000 dots, 100% coverage
• Lens Mount
Canon EF mount compatible with Canon EF lenses (including EF-S lenses)
Lens multiplication factor: approx. 1.53 (for 35mm-equivalent focal length)
• ND Filter: Built-in (Off, 2, 4 or 6 stops), manual
• White Balance
Custom white balance (two sets, A and B); two preset settings (daylight, 5,400 K and incandescent lamp,
3,200 K) that can be further fine-tuned; color temperature setting (2,000 K to 15,000 K); automatic white
balance
• Iris: Manual (1/2-stop increments, 1/3-stop increments, fine-tuning), automatic (push auto iris)
• ISO Speed
1-stop increments: ISO 320, ISO 400 to ISO 12800, ISO 20000
1/3-stop increments: ISO 320 to ISO 20000
• Gain: -6 dB to 30 dB (3-dB increments), 0 dB to 24 dB (fine-tuning in 0.5-dB increments)
• Shutter Speed
Speed (1/3-stop increments, 1/4-stop increments), angle, clear scan, slow, off
• Lens Peripheral Illumination Correction: Available for Canon EF lenses***
*** Some Canon EF lenses are not compatible with peripheral illumination correction.
• Sensor Sensitivity (ISO 640 (0 dB), 2000 lux, 89.9% reflection)
F9 (1920x1080 at 60i)
F10 (1920x1080 at 50i)
• S/N Ratio (ISO 850, using Canon Log gamma)
54 dB (typical, 1920x1080,
at PF30 /
at PF25)
Specifications
• Subject Illumination (24 dB, with an f/1.2 lens)
0.30 lux (PF30, shutter speed 1/30)
0.25 lux (PF25, shutter speed 1/25)
156
• Size of Photos: 1920x1080 pixels
Terminals
• HDMI OUT Terminal: HDMI connector, output only, supports time code output
• AV OUT Terminal
∅ 3.5 mm stereo minijack, output only
Video: 1 Vp-p / 75 Ω unbalanced
Audio: -10 dBV (47 kΩ load) / 3 kΩ or less
• USB Terminal: mini-B, Hi-Speed USB, output only
• MIC Terminal
∅ 3.5 mm stereo mini-jack, -72 dBV (manual volume center, full scale -18 dB) / 600 Ω
Microphone attenuator: 20 dB
• × (Headphone) Terminal
∅ 3.5 mm stereo mini-jack, -G to -12 dBV (16 Ω load, volume range Min to Max) / 50 Ω or less
• REMOTE Terminal: ∅ 2.5 mm stereo mini-jack
• Grip Unit Connection Terminal
Proprietary connector for the supplied Grip Unit connection plug
Power/Others
C
Y
P
O
• Power Supply (rated): 7.4 V DC (battery pack), 8.4 V DC (DC IN)
• Power Consumption (recording at 24 Mbps/24 Mbps LPCM, viewfinder/LCD screen normal brightness)
LCD screen and viewfinder:
8.1 W,
7.6 W
Viewfinder only:
7.7 W,
7.3 W
Maximum rated power consumption: 19.6 W
• Operating Temperature: 0 – 40 °C (32 – 104 °F)
• Dimensions (W x H x D)*
Minimal configuration with thumb rest:
135 x 170 x 129 mm (5.3 x 6.7 x 5.1 in.)
Configuration with grip unit:
182 x 170 x 129 mm (7.2 x 6.7 x 5.1 in.)
Configuration with handle unit and grip unit:
182 x 281 x 263 mm (7.2 x 11.1 x 9.3 in.)
* All dimensions are approximate.
• Weight **
Camcorder unit only:
1,020 g (2.2 lb.)
Camcorder with grip unit and grip belt, BP-955 battery pack and two SD cards:
1,475 g (3.3 lb.)
Camcorder with grip unit and grip belt, handle unit, BP-955 battery pack and two SD cards:
1,835 g (4.0 lb.)
** All weights are approximate.
Specifications
Modular Units
Handle Unit
Modular unit includes a cold accessory shoe and socket for 0.64 cm (1/4 in.) screws for other accessories, builtin microphone, XLR terminals and related audio controls.
• CH1, CH2 Terminals
XLR jack (pin1: shield, pin2: hot, pin3: cold), 2 sets
Sensitivity
MIC setting: -60 dBu (manual volume center, full scale -18 dB) / 600 Ω
LINE setting: 4 dBu (manual volume center, full scale -18 dB) / 10 kΩ
Microphone attenuator: 20 dB
• Microphone: Stereo electret condenser microphone
• Weight: Approx. 360 g (12.7 oz.)
Grip Unit
Modular unit can be attached at any of 24 positions (15º intervals); includes limited recording controls.
• Weight: Approx. 230 g (8.1 oz.)
CA-930 Compact Power Adapter
• Power Supply: 100 – 240 V AC, 50/60 Hz
• Rated Output / Consumption: 8.4 V DC / 24 W
C
• Operating Temperature: 0 – 40 °C (32 – 104 °F)
Y
P
O
• Dimensions (W x H x D): Approx. 85 x 51 x 110 mm (3.3 x 2.0 x 4.3 in.)
• Weight: 240 g (8.5 oz.)
BP-955 Battery Pack
• Battery Type: Rechargeable lithium ion battery, compatible with Intelligent System
• Rated Voltage: 7.4 V DC
• Operating Temperature: 0 – 40 °C (32 – 104 °F)
• Battery Capacity
Typical: 5,200 mAh
Minimum: 37 Wh / 4,900 mAh
• Dimensions (W x H x D): 38.2 x 43.5 x 70.5 mm (1.5 x 1.7 x 2.8 in.)
• Weight: 220 g (7.8 oz)
Weight and dimensions are approximate. Errors and omissions excepted.
The information in this manual is verified as of October 2012. Subject to change without notice.
157
Index
158
24P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
50.00 Hz/59.94 Hz recordings . . . . . . . . . . . . . .50
A
ABB (automatic black balance) . . . . . . . . . . . . .43
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .152
AE shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Aspect ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Assignable buttons . . . . . . . . . . . . . . . . . . . . . .85
Audio output . . . . . . . . . . . . . . . . . . . . . . . . . .115
Audio peak limiter . . . . . . . . . . . . . . . . . . . .74, 77
Audio recording . . . . . . . . . . . . . . . . . . . . . . . . .73
Audio recording level . . . . . . . . . . . . . . . . . .74, 77
Audio reference signal . . . . . . . . . . . . . . . . . . . .79
AV OUT terminal . . . . . . . . . . . . . . . . . . . . . . .113
B
Drop frame (time code) . . . . . . . . . . . . . . . . . . .70
E
Edge monitor . . . . . . . . . . . . . . . . . . . . . . . . . . .81
EF lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
EF-S lens correction . . . . . . . . . . . . . . . . . . . . .30
Exposure compensation . . . . . . . . . . . . . . . . . .60
EXT terminal . . . . . . . . . . . . . . . . . . . . . . . . . . .32
F
Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
File numbering . . . . . . . . . . . . . . . . . . . . . . . . .141
Flicker reduction . . . . . . . . . . . . . . . . . . . . . . . .55
Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Frame rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Free-run (time code) . . . . . . . . . . . . . . . . . . . . .69
G
Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Bit rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Black balance . . . . . . . . . . . . . . . . . . . . . . . . . .43
Built-in backup battery . . . . . . . . . . . . . . . . . . .150
Built-in microphone . . . . . . . . . . . . . . . . . . .73, 75
C
C
Camera settings . . . . . . . . . . . . . . . . . . . . . . . .99
Canon Log gamma . . . . . . . . . . . . . . . . . . .49, 97
CINEMA (preset custom picture) . . . . . . . . . . . .49
Clips
Converting to SD . . . . . . . . . . . . . . . . .108
Copying . . . . . . . . . . . . . . . . . . . . . . . .106
Deleting . . . . . . . . . . . . . . . . . . . . . . . .107
Playback . . . . . . . . . . . . . . . . . . . . . . .102
Saving to a computer . . . . . . . . . . . . . .117
Color bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Condensation . . . . . . . . . . . . . . . . . . . . . . . . .151
Connection to an external monitor . . . . . . . . . .112
Custom displays . . . . . . . . . . . . . . . . . . . . . . . .98
Custom functions . . . . . . . . . . . . . . . . . . . . . . .98
Custom picture . . . . . . . . . . . . . . . . . . . . . . . . .88
Detailed custom picture settings . . . . . . .91
Graphical interface . . . . . . . . . . . . . . . . .96
D
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . .25
DC IN terminal . . . . . . . . . . . . . . . . . . . . . . . . . .24
Double slot recording . . . . . . . . . . . . . . . . . . . . .41
Down-conversion (HDóSD) . . . . . . . . . . . . . .108
Y
P
O
Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Gamma curve . . . . . . . . . . . . . . . . . . . . . . . . . .96
Grip belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Grip unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
H
Handle unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
HDMI OUT terminal . . . . . . . . . . . . . . . . . . . . .112
Headphone terminal . . . . . . . . . . . . . . . . . . . . .78
Hour meter . . . . . . . . . . . . . . . . . . . . . . . . . . .134
I
Index screens . . . . . . . . . . . . . . . . . . . . . . . . .101
Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
ISO speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
J
Joystick . . . . . . . . . . . . . . . . . . . . . . . .27, 52, 104
Joystick guide . . . . . . . . . . . . . . . . . . . . . . . . .104
K
Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . .47, 60
L
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
LCD screen . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Light metering mode . . . . . . . . . . . . . . . . . . . . .61
LUT (lookup table) . . . . . . . . . . . . . . . . . . . . . . .97
M
Magnification . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Menu settings . . . . . . . . . . . . . . . . . . . . . . . . .127
Message list . . . . . . . . . . . . . . . . . . . . . . . . . . .145
MIC terminal . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Microphone attenuator . . . . . . . . . . . . . . . . .75, 78
Microphone sensitivity . . . . . . . . . . . . . . . . .75, 78
Modular units . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Monitor delay . . . . . . . . . . . . . . . . . . . . . . . . . .115
My Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Reviewing a recording . . . . . . . . . . . . . . . . . . . 82
Running mode (time code) . . . . . . . . . . . . . . . . 69
S
ND filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Non-drop frame (time code) . . . . . . . . . . . . . . . .70
Safety zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Initializing . . . . . . . . . . . . . . . . . . . . . . . 40
Inserting/Removing . . . . . . . . . . . . . . . . 39
Recording method . . . . . . . . . . . . . . . . 41
Recovering data . . . . . . . . . . . . . . . . . . 42
Switching SD card slots . . . . . . . . 41, 102
SD movies . . . . . . . . . . . . . . . . . . . . . . . 108, 110
Shutter speed . . . . . . . . . . . . . . . . . . . . . . . . . 53
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 155
Status screens . . . . . . . . . . . . . . . . . . . . . . . . 135
System frequency . . . . . . . . . . . . . . . . . . . . . . 50
O
T
One-shot AF . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Onscreen displays . . . . . . . . . . . . . . . .48, 98, 103
Onscreen markers . . . . . . . . . . . . . . . . . . . . . . .67
Tally lamps . . . . . . . . . . . . . . . . . . . . . . . . 45, 132
Terminal covers . . . . . . . . . . . . . . . . . . . . . . . . 36
Thumb rest . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Time code . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Tripod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 142
Turning the camcorder on/off . . . . . . . . . . . . . . 24
N
P
C
Peaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Peripheral illumination correction . . . . . . . . . . . .30
Phantom power (microphone) . . . . . . . . . . . . . .76
Photos
Copying . . . . . . . . . . . . . . . . . . . . . . . .122
Copying custom picture files . . . . . . . . .125
Deleting . . . . . . . . . . . . . . . . . . . . . . . .123
Viewing . . . . . . . . . . . . . . . . . . . . . . . . .121
Playback
Clips . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Photos . . . . . . . . . . . . . . . . . . . . . . . . .121
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . .21
POWER switch . . . . . . . . . . . . . . . . . . . . . . . . .24
Pre-recording mode . . . . . . . . . . . . . . . . . . . . . .83
Push auto iris . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Y
P
O
U
USB terminal . . . . . . . . . . . . . . . . . . . . . . . . . 117
User bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
V
Video configuration . . . . . . . . . . . . . . . . . . . . . 50
Video output configuration . . . . . . . . . . . . . . . 111
Video scopes . . . . . . . . . . . . . . . . . . . . . . . . . . 80
View assistance . . . . . . . . . . . . . . . . . . . . . . . . 97
Viewfinder . . . . . . . . . . . . . . . . . . . . . . . . . 32, 33
Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
R
W
Rec run (time code) . . . . . . . . . . . . . . . . . . . . . .69
Recording
Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Photos . . . . . . . . . . . . . . . . . . . . . . . . .119
Relay recording . . . . . . . . . . . . . . . . . . . . . . . . .41
Remaining battery . . . . . . . . . . . . . . . . . . . . . . .23
Resetting all camcorder settings . . . . . . . . . . .132
Resolution (frame size) . . . . . . . . . . . . . . . . . . . .50
Waveform monitor . . . . . . . . . . . . . . . . . . . . . . 80
White balance . . . . . . . . . . . . . . . . . . . . . . 62, 96
X
XLR terminals . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Z
Zebra pattern . . . . . . . . . . . . . . . . . . . . . . . . . . 68
159
USA
&N
Z
CANON CINEMA EOS LIMITED WARRANTY FOR PRODUCTS PURCHASED IN THE UNITED
STATES
160
The limited warranty set forth below is given by Canon U.S.A., Inc. ('Canon USA') with respect to (a) the Canon Cinema EOS Product, and (b) the
accessories for the Canon Cinema EOS Product (if any), packaged with this limited warranty (collectively the "Products")* and purchased in the United
States. This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase. The Products are warranted to the original
end-user purchaser, when delivered in new condition in its original container, under normal use against defective materials or workmanship as follows:
Parts: At Canon USA's option, defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of
original purchase. Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon USA's factory
service centers or designated service facilities located in the United States. When returning Products under this warranty, you must pre-pay the shipping
charges, and you must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem. During the ONE-YEAR
warranty period, repairs will be made and the Products will be return-shipped to you free of charge. For repairs after the warranty period is over, you will
be given an estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is incurred. If you approve, repairs
will be made and the Products will be returned to you at your risk and expense. If you disapprove, we will return-ship the Products to you at no charge to
you to an address within the United States.
This limited warranty only applies if the Products are used in conjunction with compatible computer equipment and compatible software, as
to which items Canon USA will have no responsibility. Canon USA shall have no responsibility under this limited warranty for use of the
Products in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Products, are sold 'AS IS' without warranty of any kind by Canon USA,
including any implied warranty regarding merchantability or fitness for a particular purpose. The sole warranty with respect to such nonCanon brand items is given by the manufacturer or producer thereof.
*Except for the battery pack packaged with the Products, which carries a separate ninety (90) day limited warranty.
In order to obtain warranty service, please contact the authorized Canon retail dealer from whom you purchased the Products or contact the CANON
INFORMATION CENTER AT 855-CINE-EOS (855-246-3367) or on the internet at pro.usa.canon.com/support. You will be directed to the nearest
service facility for your Products.
Y
P
O
This Limited Warranty covers all defects encountered in normal use of the Products and does not apply in the following cases:
A. Loss or damage to the Products due to abuse, mishandling, accident, improper maintenance, use of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions prescribed in Canon USA's user's manual;
B. If the Products are defective as a result of leaking batteries, sand, dirt or water damage;
C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon USA) that cause damage to the Products or that
cause abnormally frequent service calls or service problems;
D. If defects or damages are caused by service other than Canon USA's factory service centers or authorized service facilities;
E. Any internal modification to product hardware or firmware;
F. Any applicable fee for Maintenance of the Products;
G. If the Product has had its serial number or dating altered or removed.
C
This Limited Warranty does not apply to Products purchased outside the United States. This Limited Warranty does not apply to accessories or
consumables not originally packaged with the Product. Please retain this warranty card and your Bill of Sale as a permanent record of your purchase. This
card ensures that you are contacted promptly should there be a safety inspection, modification or Product recall under applicable laws or regulations.
NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THE PRODUCTS AFTER THE
APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THE PRODUCTS SHALL BIND CANON USA (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON USA SHALL NOT BE LIABLE FOR LOSS OF
REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE PRODUCTS OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING
WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE PRODUCTS' HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE PRODUCTS, REGARDLESS OF THE LEGAL THEORY ON
WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY
OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE PRODUCTS SOLD BY CANON USA AND CAUSING THE
ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND
YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE PRODUCTS NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF CANON USA (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU). THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE
OTHER THAN THE ORIGINAL PURCHASER OF THE PRODUCTS OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CANON U.S.A., INC.
CANADA
CANON CINEMA EOS LIMITED WARRANTY FOR PRODUCTS PURCHASED IN CANADA
The limited warranty set forth below is given by Canon Canada Inc. ('Canon Canada') with respect to (a) the Canon Cinema EOS product, and (b) the
accessories for the Canon Cinema EOS Product (if any), packaged with this limited warranty (collectively the "Products")* and purchased in Canada. This
limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase. The Products are warranted to the original end-user
purchaser, when delivered in new condition in its original container, under normal use against defective materials or workmanship as follows: Parts: At
Canon Canada's option, defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original
purchase. Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon Canada's factory service
center or designated service facilities located in Canada. When returning Products under this warranty, you must pre-pay the shipping charges, and you
must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem. During the ONE-YEAR warranty period,
repairs will be made and the Products will be return-shipped to you free of charge. For repairs after the warranty period is over, you will be given an
estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is incurred. If you approve, repairs will be made
and the Products will be returned to you at your risk and expense. If you disapprove, we will return-ship the Products to you at no charge to you to an
address within Canada.
This limited warranty only applies if the Products are used in conjunction with compatible computer equipment and compatible software, as
to which items Canon Canada will have no responsibility. Canon Canada shall have no responsibility under this limited warranty for use of the
Products in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Products, are sold 'AS IS' without warranty of any kind by Canon Canada,
including any implied warranty or condition regarding merchantability or fitness for a particular purpose. The sole warranty with respect to
such non-Canon brand items is given by the manufacturer or producer thereof.
*Except for the battery pack packaged with the Products, which carries a separate ninety (90) day limited warranty.
In order to obtain warranty service, please contact the authorized Canon retail dealer from whom you purchased the Products or contact the CANON
PROFESSIONAL SERVICE CENTRE 1-800-667-2666 or on the internet at www.canon.ca/pro. You will be directed to the nearest service facility for your
Products.
This Limited Warranty covers all defects encountered in normal use of the Products and does not apply in the following cases:
Y
P
O
A. Loss or damage to the Products due to abuse, mishandling, accident, improper maintenance, use of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions prescribed in Canon Canada's user's manual;
B. If the Products are defective as a result of leaking batteries, sand, dirt or water damage;
C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon Canada) that cause damage to the Products or
that cause abnormally frequent service calls or service problems;
D. If defects or damages are caused by service other than Canon Canada's factory service centers or authorized service facilities;
E. Any internal modification to product hardware or firmware;
F. Any applicable fee for Maintenance of the Products;
G. If the Product has had its serial number or dating altered or removed.
C
This Limited Warranty does not apply to Products purchased outside Canada. This Limited Warranty does not apply to accessories or consumables not
originally packaged with the Product. Please retain this warranty card and your Bill of Sale as a permanent record of your purchase. This card ensures
that you are contacted promptly should there be a safety inspection, modification or Product recall under applicable laws or regulations.
NO IMPLIED WARRANTY OR CONDITION, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THE
PRODUCTS AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON,
FIRM OR CORPORATION WITH RESPECT TO THE PRODUCTS SHALL BIND CANON CANADA (SOME PROVINCES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON
CANADA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE PRODUCTS OR SERVICE, STORAGE
CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE PRODUCTS'
HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE
PRODUCTS, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF
THE PRODUCTS SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK
AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE,
MISUSE OR INABILITY TO USE THE PRODUCTS NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON CANADA (SOME PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU).
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THE PRODUCTS OR THE PERSON FOR
WHOM IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from province to province.
CANON CANADA INC.
161
Canon Inc.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
ASIA and HONG KONG, S.A.R.
Canon Hongkong Company Ltd
19/F, The Metropolis Tower, 10 Metropolis Drive,
Hunghom, Kowloon, Hong Kong
+852 3191 2333,
+852 2428 3963
SINGAPORE
Canon Singapore Pte. Ltd
1 HarbourFront Avenue, #04-01 Keppel Bay Tower,
Singapore 098632
(65) 6799 8888,
(65) 6799 8882
AUSTRALIA www.canon.com.au
Canon Australia Pty Ltd
13-13-83 (within Australia only)
(61) 02-9805-2555
CANADA
CANON CANADA INC.
http://www.canon.ca/pro
❖ Professional Product Support / Soutien des
produits professionnels
(800) 667-2666
CENTRO Y SURAMÉRICA
CANON LATIN AMERICA, INC.
http://www.cla.canon.com
EUROPE www.canon-europa.com
Canon Europa N.V.
Bovenkerkerweg 59-61,
1185 XB Amstelveen, The Netherlands
NEW ZEALAND www.canon.co.nz
Canon New Zealand Ltd
0800-222-666 (within New Zealand only)
(64) 09-489-0300
C
UNITED KINGDOM
Canon UK Ltd
CCI Service Centre, Unit 130, Centennial Park,
Borehamwood, Hertfordshire, WD6 3SE
0844-369-0100
Y
P
O
USA
CANON U.S.A., INC.
http://pro.usa.canon.com
http://pro.usa.canon.com/support
(855) CINE-EOS (855-246-3367)
(USA only)
MÉXICO
CANON MEXICANA, S DE RL DE CV
http://www.canon.com.mx
52 (55) 5249-4905
Visit your local Canon Web site to download the latest version of this Instruction Manual.
0166W716
© CANON INC. 2012
PUB. DIE-0429-001
2

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Handheld camcorder 9.84 MP CMOS Black
  • Memory card
  • LCD Built-in display 8.89 cm (3.5")
  • Full HD 1920 x 1080 pixels
  • Dolby Digital
  • HDMI DC-in jack

Related manuals

Download PDF

advertisement