CyberPower RMCARD202 User`s manual
User’s Manual
Remote Management Card
RMCARD202/RMCARD203
RMCARD302/RMCARD303
Intelligent Remote Management Card
allows a UPS system/environment sensor to
be managed, monitored, and configured
Version 1.6
CyberPower Remote Management System
TABLE OF CONTENTS
Introduction .......................................................................................... 1
Installation Guide ................................................................................. 3
Web Interface ....................................................................................... 8
Reset to Default Setting/Recover from a Lost Password ................... 26
Firmware Upgrade ............................................................................. 27
Trouble Shooting ................................................................................ 28
Appendix 1 ......................................................................................... 29
INTRODUCTION
Overview
The CyberPower Remote Management Card allows for remote monitoring and controlling of a
UPS attached to a network. After installing the hardware and configuring an IP address, the user
can access, monitor, and control the UPS from anywhere in the world! Simply use a web browser
such as Internet Explorer or Firefox to access your UPS. Servers and workstations can be
protected by the UPS utilizing the PowerPanel Business Edition Client version to gracefully
shutdown when signaled by the Remote Management Card.
Features
Real time UPS monitoring
Remote management and configuration of UPS via Web Browser or NMS
Auto-shutdown to protect servers/workstations from data lost due to power failure
Schedule shutdown/start-up/reboot of the UPS via remote control
Event logging to trace UPS operational history
Data logging for analyzing power conditions
Event notification via email and SNMP traps
Support Environment Sensor management(RMCARD203/303)
Support TCP/IP, UDP, SNMP,HTTP, NTP, DNS, SMTP protocol
Support SNMPv3, HTTPS protocol (HW V2.0 above)
SNMP MIB provided
Quick installation and user friendly interface
User upgradeable firmware via FTP
MD5 Security management provided
System Requirements
A computer with a Windows or Linux Operating System (for optional PowerPanel Business
Edition Client)
An Ethernet connection to an existing network
NMS (Network Management Station) compliant with SNMP (for optional NMS management)
1
CyberPower Remote Management System
Application
Unpacking
Inspect the Remote Management Card upon receipt. The package should contain the following:
CyberPower Remote Management Card
PowerPanel Business Edition CD with Software
Quick Installation Guide
2
CyberPower Remote Management System
INSTALLATION GUIDE
Step 1. Hardware Installation
Internal smart slot Remote Management Card
1. Turn off the UPS before removing the expansion port cover on the UPS.
2. Remove the two retaining screws from the expansion port cover and remove the cover.
3. Insert the CyberPower Remote Management Card into the expansion port.
4. Re-install and tighten the retaining screws.
5. Connect the Ethernet cable to the LAN port on the CyberPower Remote Management Card.
6. To connect with the environment sensor, use RJ45 Ethernet cable. Plug one end into the
Universal connector and the other end into the sensor (RMCARD203/303).
7. Turn on the UPS.
3
CyberPower Remote Management System
RMCARD303
4
CyberPower Remote Management System
Definitions for LED Indicators
Link LED color
Condition
Off
The Remote Management Card is not connected to the Network/or
the Remote Management Card Power is off.
On (Yellow)
The Remote Management Card is connected to the Network.
TX/RX LED color
Off
The Remote Management Card power is off.
On (Green)
The Remote Management Card power is on.
Flash
- Receiving/transmitting data packet.
- Reset finished.
Step 2. Configure the IP address for the CyberPower Remote Management Card
Method 1: Using the CyberPower Power Device Network Utility Tool
1. Install the CyberPower Power Device Network Utility Tool from the included CD. It is located
in the \tools\network folder of the CD. Double click the “Power Device Network Utility”
installation file, “Setup.msi” to begin the installation.
2. After installation completes, run the “Power Device Network Utility” program. Under “All
Programs, select ”CyberPower Power Device Network Utility”.
3. The main dialog of the “Power Device Network Utility Tool” program is shown in Figure 1.
The configuration tool will display all CyberPower Remote Management Cards of present
on the same network. The "Refresh" button is used to search the entire local network for
Remote Management Cards.
Figure 1. The main window of the “Power Device Network Utility” program.
4. Select the Remote Management Card you are setting up. Click on the Tools menu and
select “Device Setup” or double click the Remote Management Card you want to configure.
5. You can modify the IP Address, Subnet Mask, and Gateway address for the Device MAC
Address listed in the Device Network Settings window, as shown in Figure 2. The default IP
Address is 192.168.20.177 and the default Subnet Mask is 255.255.255.0.
5
CyberPower Remote Management System
Figure 2. The setting window.
6. To modify the IP Address, Subnet Mask or Gateway address, enter the new addresses into
the corresponding fields.
7. You will need to enter a User Name and Password for the Remote Management Card
(Figure 3) in the authentication window, as shown in figure 3.
*Default user name: cyber; Default password: cyber
Figure 3. The authentication window.
8. If IP address is successfully set, you will see a message that the IP set up is OK, as shown
in Figure 4.
.
Figure 4. Setup IP Address successfully message.
6
CyberPower Remote Management System
Method 2: Using a command prompt
1. Obtain the MAC address from the label on the Remote Management Card rear panel. Each
Management card has a unique MAC address.
2. Use the ARP command to set the IP address.
Example:
To assign the IP Address 192.168.20.240 for the Remote Management Card,
which has a MAC address of 00-0C-15-00-00-01, you will type in the following
command prompt from a PC connected to the same network as the Remote
Management Card.
A.
Type in “arp -s 192.168.20.240 00-0C-15-00-00-01” then press Enter.
3. Use the Ping command to assign a size of 123 bytes to the IP.
A.
Type in “ping 192.168.20.240 -l 123” then press Enter.
B.
If the replies are received, your computer can communicate with the IP address.
To select an IP address for the Remote Management Card, please refer to Appendix 1.
7
CyberPower Remote Management System
WEB INTERFACE
Login Account
There are two types of user account:
Administrator (default username: cyber; default password: cyber)
Viewer (default username: device; default password: cyber)
The Administrator can access and control all functions, including enable/disable of the
Viewer account. The Viewer’s access possesses read permissions for all functions but
cannot control or change any settings.
Note: 1. The Administrator account is also used for the FTP log in and
authentication check in the Power Device Network Utility.
2. The Login process uses MD5 algorithm to protect the username and
password.
Web Content
[Summary] Provide an overview of the system operation and the items that are auto refreshed;
However, different model of RMCARD may have different items displayed.
Item
Current Condition
Definition
Display the current operating condition of UPS and
environment sensor.
UPS Status
Battery Capacity
Load
Remaining Runtime
The percentage of the current UPS battery capacity in a
graph.
The load of UPS as a percentage of available Watts in a
graph.
How long the UPS can support its load by battery power.
System Data
Name
The name of the equipment.
Location
The Location of the equipment.
Contact
The person to contact about this equipment.
Uptime
How long the system has been working continuously.
Envir
Temperature
The current temperature of the environment in a graph.
8
CyberPower Remote Management System
Humidity
The current humidity of the environment in a graph.
Envir Data
Name
The name of the environment sensor.
Location
The location of the environment sensor.
Recent Device Events
List the latest 5 events that occurred recently.
[UPS] Following items can be displayed/configured through the UPS page; however, different
UPS may have different items displayed/configured.
[UPS->Status] Display the basic information about the current UPS status and the items are
auto refreshed.
Item
Definition
Input
Status
Display the present status of the utility power
supplied to the UPS.
Voltage
The current input voltage of the utility power.
Frequency
The current frequency of the utility power supplied to
the UPS.
Output
Status
Voltage
Frequency
Load
Non-Critical Bank
Display the present status of the output power the
UPS is supplying to connected equipment.
The output voltage the UPS is supplying to the
connected equipment.
The output frequency the UPS is supplying to the
connected equipment.
The percentage of the total UPS capacity that is
being supplied to the connected equipment. This is
displayed as Watts in some UPS models.
Display the present status of the NCL outlet.
Battery
Status
Display the present status of the battery packs.
Remaining Capacity
The percentage of the current UPS battery capacity.
9
CyberPower Remote Management System
Remaining Runtime
How long the UPS can support its load under battery
mode.
System
Temperature
The temperature inside the UPS.
[UPS->Information] Provide the technical specifications of the connecting UPS.
Information
Description
Model Name
The model name of the UPS.
Voltage Rating
The output voltage rating (Volts) of the UPS.
Working Frequency
The output frequency rating (Hz) of the UPS.
Power Rating
The Volt-Amp rating of the UPS.
Current Rating
The output current rating (Amps) of the UPS.
Load Power
The power rating (Watts) of the UPS.
Battery Voltage Rating
The DC voltage rating of the battery set.
Firmware Version
The version number of the UPS firmware.
USB Version
The version number of the UPS USB firmware
LCD Version
The version number of the UPS LCD firmware
Battery Replacement Date
The date that the batteries were last replaced This
must be set manually and should be set after the
batteries have been replaced or when the unit is first
installed. If this date has not been set, it is
recommended that this date should be set
immediately.
Non-Critical Bank
The amount of the Non-Critical Load.
External Batteries
Installation Place
The amount of the external battery packs connected
to the UPS.
When clicking the “Find it” button, either the alarm
will beep or the indicators will flash to inform users of
the location. This helps users to identify a specific
UPS in a multiple UPS installation.
10
CyberPower Remote Management System
[UPS->Configuration] Configure the parameters of the UPS.
Item
Definition
Supplied Power
Voltage
Set the output voltage which is supplied to
the connected equipment.
Utility Power Failure Condition
High/Low Input (or Output)
Voltage Threshold
Frequency Tolerance
When the utility power voltage or output
voltage (according to the UPS support) is
higher/lower than the threshold, the UPS will
supply battery power to the connected
equipment. This setting only comes into
effect after a restart of the UPS.
Sets the acceptable range of the input
frequency. It will be in power failure condition
if out of this tolerance.
Operation
Normal
Generator Mode
ECO Mode
Manual Bypass
Normal working mode of the UPS.
If the UPS uses generator as its input power,
this option should enable the UPS to function
normally. If this option is selected, the UPS
will be forbidden to enter Bypass mode or
ECO mode to protect the powered
equipment.
On-line UPS enters Economy mode. The
UPS will enter Bypass mode when the input
voltage/frequency is in the range of
thresholds. Once the utility
voltage/frequency exceeds thresholds, the
UPS will supply power to its load.
Determine whether to allow the UPS to enter
Manual Bypass mode. If this option is
selected, the UPS will be forced to enter
Bypass mode.
Bypass
Qualify Bypass
No Bypass: If this option is selected, the
UPS will not enter Bypass mode and will
stop supplying output power.
Check Volt/Freq: If the utility voltage is in
range of the voltage thresholds and the utility
frequency is in range of the frequency
tolerance, the UPS will enter Bypass mode.
11
CyberPower Remote Management System
High/Low Bypass Voltage
Power Restore
Recharged Delay
Recharged Capacity
Returned Delay
Otherwise the UPS will stop supplying output
power.
Check Volt Only: Only if the utility voltage is
in the range of the voltage thresholds, the
UPS will enter Bypass mode. Otherwise the
UPS will stop supplying output power.
When the UPS fault or overload occurs, the
UPS will determine whether to enter Bypass
mode according to the range of thresholds of
utility voltage. If the utility voltage exceeds
thresholds, the UPS will be forbidden to
enter Bypass mode and stop supplying
output power.
After utility power is restored, the UPS turns
on automatically and supplies power to the
computer. If the computer BIOS is set to boot
when power restores, the computer will
restart automatically. The following settings
are used to configure the UPS restore
actions:
When utility power is restored, the UPS will
start to recharge after the specified delay is
expired.
When utility power is restored, the UPS will
start to recharge after the specified battery
capacity is met.
When utility power is restored, the UPS will
delay the restoration of output power. This
option can be used to stagger the startup
time of multiple UPSs to avoid overloading
the utility power circuit or power source. The
Returned Delay will take effect every time
when the UPS restores power. This also
includes the scheduling and user controlling
task.
Battery
Low Battery Threshold
External Battery Pack
When the UPS supplies battery power and
the remaining capacity is lower than this
threshold, the UPS will alarm.
Set the amount of external battery packs.
This allows for an accurate runtime
estimation based upon the total number of
batteries.
System
Cold Start
Set the ability of the UPS to start in the
absence of input power. When this option is
12
CyberPower Remote Management System
Audible Alarm
Dry Relay Function
Screen Saver Time
Wiring Fault Detect
enabled, the UPS can be turned on without
input power.
If this option is enabled, the UPS will issue
an audible alarm when supplying battery
power or output overload.
This configures the power condition for the
UPS dry relay to function when the selected
condition occurs. Refer to UPS manual for
further information about advanced UPS dry
relay utilization. The Dry Relay Function
provides following power conditions:
Utility Failure: The utility power fails and the
UPS is using battery power.
Low Battery: The battery capacity is too low
to support the connected computers to
shutdown.
Alarm: The UPS is issuing the audible alarm
due to the occurrence of warning events,
such as overload.
Bypass: The UPS has switched to Bypass
mode due to overload or UPS fault.
UPS Fault: The UPS could be malfunctioned
due to hardware fault, such as inverter fault,
bus fault or overheated.
When no UPS button is pressed or no power
event occurs during this delay, the LCD
screen will be turned off.
If this option is enabled, the UPS will detect if
the UPS wiring is not grounded or is
reversed. It is recommended to assure the
UPS wiring has ground connection first. This
option should be enabled if the UPS wiring
has ground connection.
Non-Critical Outlet Bank
Turn Off Threshold
Turn off Delay Time
Turn On Delay Time
When supplying battery power, the UPS will
power off the NCL outlet if the remaining
battery capacity is lower than this threshold.
When supplying battery power, the UPS will
power off this NCL outlet after this delay time
is met.
When utility power is restored, the UPS will
restore the output of the NCL outlet after the
delay time is met. This prevents excessive
power consumption caused by all the
connected equipment rebooting at the same
time.
13
CyberPower Remote Management System
[UPS->Master Switch] Switch the output power of the UPS to be on or off.
Item
Definition
Reboot UPS
Turn the UPS off and back on
Turn UPS Off
Turn the UPS off.
UPS Sleep
This command is available under Utility Power
Failure Mode. It will make UPS under sleep mode
until power is restored.
Cancel Switch
Cancel a pending action to turn the UPS off.
Turn UPS On
Turn the UPS on.
Shutdown/Sleep Delay
Reboot Duration
Signal Clients to Shutdown
How long the UPS waits before it turns off in
response to a "Reboot UPS", "Turn UPS off" or "UPS
Sleep" command.
After the UPS is turned off, Reboot Duration defines
how long the UPS waits before it turns on in
response to "Reboot UPS" command.
Select this option to notify PowerPanel Business
Edition Clients before UPS turning off.
The Shutdown Delay for the UPS can be modified to
ensure a graceful shutdown.
[UPS->Bank Control] Display the current status of each Bank. Also, it provides on/off control for
the Non-Critical Outlet Bank. Outlet Index and Device Name display the device that is powered
by the specific bank.
Item
Definition
Non-Critical
Turn the non-critical bank on/off immediately.
Outlet Index
The index of outlet.
Device Name
Device Name on this outlet.
[UPS->Diagnostics] When a power failure occurs, the UPS will supply battery power to all
connected equipment immediately. The UPS must have sufficient runtime for all connected
computers to be shut down properly.
The UPS/Diagnostics page provides the information to verify if the UPS has sufficient battery
runtime for the connected computers to shutdown properly. Perform a complete runtime
calibration to ensure an accurate estimate of the runtime for the connected load.
Battery Test
The Battery Test will force the UPS to switch to battery power for 10 seconds. This allows the
14
CyberPower Remote Management System
user to verify the battery conditions and provides information about the battery, including the
results and date of the last battery test. Click the Initiate button to begin a battery test.
Performing a battery test is prohibited when the Frequency Working Mode option is set to fixed.
If performing a battery test on the fixed frequency mode, a UPS fault may occur and cause the
UPS to enter Bypass mode. The frequency on Bypass mode may not be accepted and may
damage the connected equipment.
The results will be reported after a battery test completes.
• Last Test Date: The date the last battery test was performed.
• Last Test Result: The results of the last battery test.
Passed: The battery performs normally during the test.
None: The UPS has never performed the battery test.
Failed: The battery test results in failure.
Follow the steps below if the battery test fails:
Repeat the battery test and replace the batteries if the test fails again.
Contact CyberPower for assistance if the battery test fails after the batteries have been
replaced.
Runtime Calibration
The Runtime Calibration ensures the runtime estimate is accurate with the load and the current
battery capacity. The results show the runtime, the results, and the date of the last calibration.
When a runtime calibration is initiated, the connected equipment will be run on battery power
until the batteries are completely discharged. Following the Runtime Calibration, the UPS will
automatically begin recharging the batteries.
Users can click the Start button to initiate a runtime calibration. Click the Cancel button to stop
the runtime calibration. The result will be reported after a calibration is finished or canceled.
• Estimated Runtime: The estimated runtime of the batteries.
• Last Calibration Elapsed Time: The elapsed time of last Runtime calibration.
• Last Calibration Result: The results of the last runtime calibration.
Passed: The runtime calibration is completed and the batteries are good.
None: The UPS has never performed a runtime calibration.
Failed: The UPS fails during the runtime calibration.
Canceled: The calibration was interrupted.
• Last Calibration Date: The last date performing the runtime calibration.
Note: 1. It is recommended to perform at least one calibration every 3 months.
2. A complete calibration causes the battery capacity to deplete. Ensure the UPS has
recharged completely after performing a calibration.
[UPS->Schedule]: Sets the UPS to automatically shutdown and restart at scheduled times (one
time/per day/per week). The Schedule page manages scheduled shutdowns and lists all
configured schedules. Each schedule row displays the details of when the schedule will take
effect and when to perform it.
15
CyberPower Remote Management System
[One Time]: The user may set a specific date and time for the UPS shutdown.
[Per Day]: Set a specific time of the day for the UPS shutdown.
[Per Week]: Set a specific day and time of the week for the UPS shutdown.
1.
2.
3.
Click [One Time], [Per Day] or [Per Week] option and Click “Next>>”, Enter the date and
time to shut down the UPS. Select [Never], [Immediately], or the date and time for the UPS
to restore power. Select the bank to be controlled, and click “Shutdown Clients” to set all
clients to perform a graceful shutdown. You can enter a comment for this Schedule.
Click [Apply] to add the item to the Schedule. Click [Reset] to remove the item from the
Schedule.
Applied settings are listed in [Schedule] menu.
Note: The management system allows up to 10 scheduled settings.
[UPS->Wake on Lan] This function is used to wake the PC through the network. (Make sure the
PC hardware has such function supported and configures as "Enable" under BIOS). Enter the IP
address of that PC when it is on and the system will search its MAC accordingly. The maximum
number of IP that can be set is 50.
[UPS->PowerPanel Clients] Display the Information of connected PPBE (PowerPanel Business
Edition) Clients. The connection is executed by PPBE Clients and the listed clients will be
removed if disconnected for 1 hour.
[Envir] Following items can be displayed/configured through the Envir page (RMCARD 203/303
only).
[Envir->Status] Display the basic information of the environment sensor and connected devices.
Item
Definition
Information
Name
The name of the environment sensor.
Location
The location of the environment sensor.
Temperature
Current Value
Maximum
Minimum
The current temperature of the environment.
The highest temperature as well as the time of
occurrence detected by the environment sensor.
The lowest temperature as well as the time of
occurrence detected by the environment sensor.
Humidity
Current Value
The current humidity of the environment.
16
CyberPower Remote Management System
Maximum
Minimum
Contact
The highest humidity as well as the time of
occurrence detected by the environment sensor.
The lowest humidity as well as the time of
occurrence detected by the environment sensor.
Display the name and status (Normal/Abnormal) of
contacts.
[Envir->Configuration]
Item
Definition
Information
Name
The name used to identify the environment sensor.
Location
The place where the environment sensor is located.
Temperature
High Threshold
Upper limit for normal temperature.
Low Threshold
Lower limit for normal temperature.
Hysteresis
Rate of Change
Unit
The difference between High/Low Threshold and the
point where the temperature state is from abnormal
to normal.
The rate used to define abnormal change of
temperature.
The unit of temperature.
Humidity
High Threshold
Upper limit for normal humidity.
Low Threshold
Lower limit for normal temperature.
Hysteresis
Rate of Change
The difference between High/Low Threshold and the
point where the humidity state is from abnormal to
normal.
The rate used to define abnormal change of
humidity.
Contact
Name
The name used to identify the contact.
State
The state used to define normal condition of the
contact.
17
CyberPower Remote Management System
[Logs->Event Logs] Display the list of events and a brief description of each event along with
the date and time stamp.
Note: 1. The recordable events are listed under “System->Notifications->Event Action.”
2. The recorded time is using the 24-hour clock format.
[Logs->Status Records] This page is used to view the logs of the UPS status and environment
status; however, different product may have different items displayed.
All items have the same definition as they are in the UPS status or environment status.
Input min (V): The minimum input voltage of the utility power from the previous record.
Input max (V): The maximum input voltage of the utility power from the previous record.
Input (Hz): The current frequency of the utility power supplied to the UPS.
Output (V): The output voltage of the UPS supplying to the connected equipment.
Output (Hz): The output frequency of the UPS supplying to the connected equipment.
Load (%): The percentage of the total UPS power load supplying to the connected
equipment.
Capacity (%): The percentage of the current UPS battery capacity.
Remaining Runtime: How long the UPS can support its load under battery mode.
Temperature: The current temperature of the environment.
Humidity: The current humidity of the environment.
[Logs->Graphing] This page is used to diagram the data of the Status Record. The graphing
function makes the status records easier to be analysed.
Item
Graph Period
Graph Data
Graph Node
Launch Graph in New
Window
Definition
The period used to draw the graph backward from
today. The longer period selected, the more graphing
time is needed.
The data used to draw the graph. The more data
selected, the more graphing time is needed.
Select Display All Nodes in Detail will display all the
points along with the line; meanwhile, moving the
cursor on the point will show the information of that
point. If the box is not selected, the graph will show
the line only but less graphing time is needed.
Click the box will open a new page showing the graph
in detail.
[Logs->Maintenance] This page is used to maintain “Event Logs” and “Status Records”. The
application provides information on how many events have been recorded before it is full.
Item
Definition
18
CyberPower Remote Management System
Event Logs
Clear All
Clear the existing event logs.
The Number of Events
The number of existing event logs/the max number of
event logs.
Save Event Logs
Save the existing event logs as a txt file.
Status Records
Recording Interval
Set the frequency to record the status data.
A smaller interval will provide more frequent
recordings but maintain them for a shorter period. A
larger interval will provide less frequent recordings,
but maintain them for a longer period.
Clear All
Clear the existing status records.
Remaining Time
The remaining recordable time base on the recording
interval.
Save Status Records
Save the status records as a txt file.
Note: Some old event logs/status records will be cleared automatically when there is no
space to record.
[System->General->User Account] This page is used to configure the login account.
Information
Administrator
Viewer
Manager IP
Description
The administrator can access full function, including
enable/disable the Viewer account.
The viewer can access the read function but can not
control or change any settings.
This IP setting is to set the allowable IP addresses.
Users who log in as Admin (Viewer) can access
RMCARD web pages if its IP Address is in one of Admin
(Viewer) Manager IPs. If you want to access RMCARD
from any IP address, you can set one of them as 0.0.0.0
or 255.255.255.255.
Change Administrator account:
• Enter User Name
• Enter Current Password for Authentication
• Set the Manager IP (optional)
• Enter New Password
• Enter Confirm Password
• Click “Apply”
19
CyberPower Remote Management System
Change Viewer account:
• Select “Allow Access” to enable the Viewer account
• Enter the User Name
• Set the Manager IP (optional)
• Enter New Password
• Enter Confirm Password
• Click “Apply”
[System->General->Date & Time]Current Settings: Displays the current date and time on the
card and allows users to set the date and time. To set the date and time, users can choose to set
manually or by using the NTP (Network Time Protocol) server.
System Time Configuration:
Choose the Time Zone off your location first, and
Using NTP server: Enter the IP address/domain name of NTP servers, choose the time
zone, and set the frequency to update the date and time from NTP server. Choose "Update
right now" to update immediately.
Manual Setup: Enter the date and time in the designated format.
[System->General->Identification] Assign the system’s name, contact, and location.
Item
Definition
Name
The name of the equipment.
Contact
Where the power equipment is located.
Location
The person to contact about this equipment.
[System->General->Security] Set for security setting.
Item
Timeout
Secret Phrase
Definition
The period (in minutes) that the system waits before
auto logging off
The Authentication Phrase used to communicate with
PowerPanel Business Edition Client
[System->Network Service->TCP/IPv4] Display the current TCP/IP settings: IP address,
Subnet Mask, Gateway, and DNS server. This also provides the function to obtain TCP/IP
settings from the DHCP server.
DHCP: Select the “Enable DHCP” option and click Apply to get IP address, Subnet
Mask, and Gateway by DHCP. Select the “Obtain DNS Address from DHCP” option
and click Apply to get the IP of DNS from the DHCP.
Manual : Enter the TCP/IP settings directly and click Apply.
[System->Network Service->TCP/IPv6] Display the current the IPv6 settings.
20
CyberPower Remote Management System
-
IPv6 Interface: Displays the current IPv6 address.
IPv6 Gateway: Displays the current IPv6 gateway.
IPv6 Configuration:
- Allow Access: Set the IPv6 service to either Enable or Disable.
- Router Control: The IPv6 address is assigned through the method (Stateless
Address Autoconfiguration, Stateless DHCPv6 or Stateful DHCPv6) which is
decided by router setting.
- Manual: The IPv6 address is assigned by manuel setting.
Manual IPv6 Address : Enter the IPv6 address directly and click Apply when the
Manuel box is checked.
[System->Network Service->SNMPv1 Service] Allow users to select the NMS, defined by the
IP settings that can use the channel to control the system data access through SNMPv1 Service.
Item
Allow Access
Community Name
IP
Access Type
Definition
Set the SNMP service to either Enable or Disable.
The name used to access this community by a
Network Management System (NMS).
The field must be 1 to 15 characters length.
The IP address or IP address mask can be accessed
by NMS. A specific IP address allows access only by
the NMS with the specified IP Address. The 255 is
regarded as the mask and the rules list as follows:
‧192.168.20.255: Access only by an NMS on the
192.168.20 segment.
‧192.255.255.255: Access only by an NMS on the
192 segment.
‧0.0.0.0 (the default setting) or 255.255.255.255:
Access by any NMS on any segment.
The allowable action for the NMS through the
community and IP.
Read Only
Gets at anytime but cannot SETS.
Write/Read
Gets at anytime, SETs anytime unless someone is
logged in the Web interface.
Forbidden
No GETS or SETS.
[System->Network Service->SNMPv3 Service] Allow users to enable/disable SNMPv3 service
and configure the parameters of accessing through SNMPv3 service (HW V2.0 above only).
Item
Allow Access
Definition
Set the SNMPv3 service to either Enable or Disable.
21
CyberPower Remote Management System
User Name
Authentucation Password
Privacy Password
IP
The name to identify SNMPv3 user. The field must be
1 to 31 characters length.
The password used to generate the key used for
authentication. The field must be 16 to 31 characters
length.
The password used to generate the key used for
encryption. The field must be 16 to 31 characters
length.
The IP address or IP address mask can be accessed
by NMS. A specific IP address allows access only by
the NMS with the specified IP Address. The 255 is
regarded as the mask and the rules list as follows:
‧192.168.20.255: Access only by an NMS on the
192.168.20 segment.
‧192.255.255.255: Access only by an NMS on the
192 segment.
‧0.0.0.0 (the default setting) or 255.255.255.255:
Access by any NMS on any segment.
Authentucation Type
The hash type for authentication.
Privacy Type
The type for encrypting and decrypting data.
[System->Network Service->Web Service] Select Enable to allow access to the HTTP or
HTTPS(HW V2.0 above only) Service and configures the TCP/IP port for them. Use the “Valid
Certificate” to browse the detailed information of HTTPS Certification;use the “upload
Certificate” to upload and replace the HTTPS Certification.
Note: The format of uploading certificate must in a standard PEM(Privacy Enhanced Mail).
[System->Network Service->Telnet Service] Selects Enable to allow access to the Telnet
Service and configures the TCP/IP port that Telnet uses to communicate (23 by default).
Note: To enhance security, users can change port setting to any unused port from 5000 to
65535. Users must then specify the non-default port to obtain access. Telnet clients
require users to append either a space and the port number or a colon and the port
number to the command line to access the control console.
[System->Network Service->FTP Service] Allows users to Enable/Disable the FTP server
service and configure the TCP/IP port of the FTP server (21 by default).
Note: The FTP server is used for upgrading Firmware. For more details about the upgrade
process, please refer to “Firmware Upgrade” section.
[System->Notifications->Event Action] Display the event actions for each event. Users can
click on the event to modify its action. When a specific event happens, the user can be notified by
the corresponding method according to this list.
22
CyberPower Remote Management System
-
Log: Record the event in the “Event Logs”.
E-mail: Send an email to a specific user (An available SMTP server is necessary).
Trap: A SNMP trap sent to a specific IP address.
SMS: Send a short message to a specific mobile phone number (An available SMS
service provider is needed).
[System->Notifications->SMTP Server] After setting the proper SMTP server, the UPS can
send an email to users when a specific event occurs.
Item
Server's IP/Host Name
Sender's E-mail Address
Authentication
Definition
The IP or Host Name of SMTP server used to notify
users by E-mail.
The context of From field shown in the e-mail
message sent to user.
Select this option if the SMTP server needs
Authentication check.
Username
Username used for Authentication.
Password
Password used for Authentication.
[System->Notifications->E-mail Recipients] Sets up to five e-mail recipients in designated
email address format. The Recipients will receive an e-mail notification when Events occur.
To add a new recipient, click New Recipient. To modify or delete an existing Recipient, click the
e-mail address of that recipient. To check if SMTP setting and the email recipients are set
correctly, click TEST button to check receiving status.
[System->Notifications->Trap Receivers] List of NMS IP as TRAP receiver, and the number of
receivers can be set up to 10. The receiver will receive a SNMP trap when an event occurs.
To add a new receiver, click New Receiver. To modify or delete an existing receiver, click the IP
address or name of that receiver. To check if the traps can be received correctly, click TEST
button.
[System->Notifications->SMS Service] Short Message Service (SMS) is a communication
service used by mobile communication systems. Using standardized communication protocols
will allow the interchange of short text messages between mobile devices. The system provides
4 methods to users to choose how they want to send the messages.
Information
Service provider is Clickatell
Description
Select the Clickatell option in the SMS
Method field. Complete all the account
details including Username, Password
and HTTP API ID fields.
23
CyberPower Remote Management System
Service provider accepts HTTP GET
Service provider accepts HTTP POST
Service provider accepts E-mail(SMTP)
This specification from the SMS provider
is required before using the HTTP GET
method. Select the Using HTTP GET
option in the SMS Method field. Insert
the E_PHONE_NUMBER as recipient's
mobile phone number and the
E_PHONE_MESSAGE as event
message, describe in the specification,
and fill in the URL field. The expressions
will be replaced by relevant content
before the Client sends a notification to
SMS provider.
This specification from the SMS provider
is required before using the HTTP POST
method to deliver messages to SMS
providers. Select the Using HTTP POST
option in the SMS Method field. Insert
E_PHONE_NUMBER as recipient's
mobile phone number and
E_PHONE_MESSAGE as the event
message, describe in the specification,
and fill in the POST URL and POST
BODY fields. The expressions will be
replaced by the relevant content before
the Agent/Client sends a notification to
the SMS provider.
This specification from a SMS provider is
required before using the E-mail to
deliver the messages to SMS providers.
Select the Using E-mail option in the
Service Provider field. Insert
E_PHONE_NUMBER as recipient's
mobile phone number and the
E_PHONE_MESSAGE as event
message, describe in the specification.
Fill in the Recipient’s Address, Subject
and Content. The expressions will be
replaced by the relevant content before
the Agent/Client sends a notification to
the SMS provider.
[System->Notifications->SMS Recipients] Users can set up to 10 mobile phone numbers as
SMS recipients. The Recipients will receive a short message notification when events occur.
To add a new recipient, click New Recipient. To modify or delete an existing Recipient, click the
mobile number or Name of that recipient. To test SMS settings, click TEST button and see if the
test message is correctly received.
24
CyberPower Remote Management System
[System->About] Display vital information for the Remote Management Card.
Item
Definition
Model Name
Model name of the Remote Management Card.
Firmware Version
The version number of the current firmware installed
on Remote Management Card.
Firmware Updated Date
The date the firmware was last updated.
Hardware Version
MAC Address
Save Configuration
Restore Configuration
The hardware version of the Remote Management
Card.
MAC address of the Remote Management Card.
Note: the MAC address is also listed on the top of the
Remote Management Card.
Click Save to save the configuration to local PC. The
text file will have a default format of
YYYY_MM_DD_HHMM.txt.
Use this function to restore a configuration that has
been saved earlier. Click Browse to the location of the
saved configuration file and click Submit.
25
CyberPower Remote Management System
Reset to Default Setting / Recover from a Lost Password
To reset the CyberPower Remote Management Card to its default setting (including WEB log-in
user name and password), please use the following steps
RESET
RMCARD202
RMCARD203
RESET
RMCARD302
RMCARD303
1. Remove the two retaining screws on the card without turning off the UPS.
2. Uninstall the card.
3. Take off the jumper on the Reset pins as illustrated (the jumper is still necessary after reset,
please do not lose or dispose it).
4. Re-install the card into the expansion port.
5. Wait until the Green LED is flashing (the frequency of the ON/OFF flashing is one second).
6. Uninstall the card again.
7. Place the jumper back onto the Reset pins.
8. Install card into the expansion port again.
9. Tighten the retaining screws.
26
CyberPower Remote Management System
Firmware Upgrade
By upgrading the Firmware, you can obtain both the new features and updates/improvements to
existing functionality. There are two files to update in order to upgrade the firmware version.
RMCARD202/RMCARD203 upgrade files:
(HW V2.0)
A. cpsrm2sbfw_XXX.bin
B. cpsrm2sbdata_XXX.bin
(HW V1.0)
A. cpssnmpfw_XXX.bin
B. cpssnmpdata_XXX.bin
RMCARD302/RMCARD303 upgrade files:
(HW V2.0)
A. cpsrm3sbfw_XXX.bin
B. cpsrm3sbdata_XXX.bin
(HW V1.0)
A. cpsrm302afw_XXX.bin
B. cpsrm302adata_XXX.bin
Use the following steps to upgrade the firmware.
1.
2.
3.
4.
Download the latest Firmware
Extract the file to “C:\”
Open a command prompt window
Login to the CyberPower Remote Management Card with FTP command, type
ftp
ftp> open
To [current ip of RMCARD] [port]; EX: To 192.168.22.126 21
Input USER NAME and PASSWORD (same as the administrator account in Web
interface default : cyber ; cyber)
5. Upgrade the file A, type
ftp > bin
ftp > put A
(RMCARD202 for ex., put cpssnmpfw_XXX.bin)
6. Upgrade complete, type
ftp > quit
7. The system will reboot after you type “quit”
8. Login to the FTP again as step 4.
9. Upgrade the file B, type
ftp > bin
ftp > put B
(RMCARD202 for ex., put cpssnmpdata_XXX.bin)
10. Upgrade complete, type
ftp > quit
11. The system will reboot after you type “quit”
You can check to see if the firmware upgrade was successful by checking the ”Firmware version”
on the [System->About] webpage.
Note: Please do not turn the UPS off when processing the Firmware upgrade.
27
CyberPower Remote Management System
Trouble Shooting
Problem
Unable to configure the
Management Card by method
1 or method 2 in user’s
manual.
Solution
1. Check the LED status, the normal condition is
when yellow and green LED are both on.
If green LED is off:
=> Check the Management Card for proper seating
in the UPS and the UPS power is on.
If yellow LED is off:
=> Ensure the network connection is valid
2. Ensure the PC being used is on the same
physical network as Remote Management Card.
3. Ensure the Jumper on the Reset Pin is correctly
installed.
1. Use method 1 and method 2 in user’s manual to
get/set a correct IP address for the Remote
Management Card.
Unable to ping the
Management Card.
Lost user name and password.
Default Network Setting?
Unable to access the Web
Interface.
Unable to operate a SNMP
get/set.
Unable to receive traps.
2. If the PC being used is on a different physical
network from the Remote Management Card, verify
the setting of subnet mask and the IP address of
gateway.
Please refer to the “Reset to Default Setting /
Recover from a Lost Password” section of the
user’s manual.
IP: 192.168.20.177
Subnet mask : 255.255.255.0
DHCP: On
1. Ensure the Http/Https access is enabled.
2. Ensure you can ping the RMCARD.
3. Ensure you are specifying the correct URL.
SNMPv1: Verify the community name.
SNMPv3: Verify the user profile configuration.
1. Ensure the trap types (SNMPv1/SNMPv3) and
trap receiver are configured correctly.
2. Ensure the IP address of gateway is configured
correctly if the RMCARD and NMS is on a different
physical network.
28
CyberPower Remote Management System
Appendix 1. IP Address Settings for CyberPower Remote Management Card
Overview
All devices on a computer network need to have an IP address. Each device’s IP address is
unique. The same address cannot be used twice. In order to assign an IP address to the
CyberPower Remote Management Card, you must determine the range of the available IP
addresses, and then choose an unused IP address to assign to the Remote Management Card.
PLEASE NOTE: You may need to contact your network administrator to obtain an available IP
address.
Procedures to find an IP address:
1. Locate the subnet of CyberPower Remote Management Card.
One way to determine the range of possible IP addresses is to view the network
configuration on a workstation. Click on [Start] and select [Run]. Type “command” into the
open box and click [OK]. At the command prompt type “ipconfig /all” and press [Enter]. The
computer will display network information as listed below:
Ethernet adapter
Connection-specific DNS Suffix…………: xxxx.com
Description……………………: D-Link DE220 ISA PnP LAN adapter
Physical Address…………….: 00-80-C8-DA-7A-C0
DHCP Enabled……………....: Yes
Autoconfiguration Enabled ...: Yes
IP Address…………………..: 192.168.20.102
Subnet Mask………………..: 255.255.255.0
Default Gateway……..……...: 192.168.20.1
DHCP Server…………..…….: 192.168.20.1
DNS Servers…………………: 211.20.71.202
168.95.1.1
2. Select an IP Address for CyberPower Remote Management Card
Verify the IP Addresses for the computer and the Remote Management Card belong to the
same subnet. Refer to the above network information, the possible IP Address for the
Remote Management Card could be 192.168.20.* (* hereafter represents any number
between 1 and 255). Similarly, if the Subnet Mask is 255.255.0.0, the IP Address for
Remote Management Card could be set up as 192.168.*.* to reach the same subnet with
the computer.
To verify there is no other equipment connected to the network using the same IP Address,
run “Ping 192.168.20.240” at the DOS Mode prompt when the IP Address you would like to
set is 192.168.20.240. If the response is presented as below, the IP address is most likely
not used and may be available for the CyberPower Remote Management Card.
Pinging 192.168.20.240 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
29
CyberPower Remote Management System
If the response is shown as below, the IP address is in use. Try another IP address until an
available address is found.
Pinging 192.168.20.240 with 32 bytes of data:
Reply from 192.168.20.240: bytes=32 time<10ms TTL=64
Reply from 192.168.20.240: bytes=32 time<10ms TTL=64
Reply from 192.168.20.240: bytes=32 time<10ms TTL=64
Reply from 192.168.20.240: bytes=32 time<10ms TTL=64
30
CyberPower Remote Management System
CyberPower Systems (USA), Inc.
4241 12th Avenue East, Suite 400, Shakopee, MN 55379
Phone: (952) 403-9500 Toll-free: (877) 297-6937
Website: www.CPSww.com
E-mail: tech@cpsww.com
CyberPower Systems, Inc.
Website: www.cpsww.com
31
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising