Bissell | 76X6 | User`s guide | Bissell 76X6 User`s guide

Bissell 76X6 User`s guide
™
USER’S GUIDE
76X6/94Z2 SERIES 220-240v
3
Safety Instructions
4
Product View
5-6
Assembly
6-9
Operations
10-15
Maintenance and Care
16-17
Troubleshooting
18
Consumer Services
19
Additional Accessories
19
Replacement Parts
20
Warranty
Thank you for buying a BISSELL Multi Cyclonic vacuum
We’re glad you purchased a BISSELL vacuum. Everything we know about floor
care went into the design and construction of this complete, high-tech home
cleaning system. By purchasing this product you are helping BISSELL with our
commitment to reducing our impact on the environment through an expanding
range of sustainable design efforts.
Your carpet cleaner is well made, and we back it with a limited one-year warranty.
We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a
global leader in the design, manufacture, and service of high quality homecare
products like your carpet cleaner.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
22
www.bissell.com
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance,
basic precautions should be observed,
including the following:
■ Remove plug from electrical outlet before cleaning or
Read all instructions
before using your
Canister VACUUM.
by the manufacturer or its service agent in order to
avoid a hazard.
■ Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, petrol, etc.).
■ Do not use for any purpose other than described in
this User’s Guide.
■ Use only manufacturer’s recommended attachments.
■ Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
■ Keep appliance on a level surface.
■ Turn off all controls before unplugging.
■ Be extra careful when cleaning stairs.
■ This appliance is provided with double
insulation. Use only identical replacement parts.
■ Do not use without the dust bag and filters in
place.
■ Pay close attention when working
around children.
■ Unplug from outlet when not in use and before
servicing.
■ Do not put any object into openings
WARNING:
To reduce
the risk of fire, electric shock,
or injury:
■ Use indoors only.
■ For dry pick up only.
■ Do not leave machine when it is plugged in.
■ Do not use with damaged cord or plug.
■ If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, return it to a service agent.
■ Do not handle unit with wet hands.
■ Do not pull or carry by cord, use cord as a handle,
close door on cord, pull cord around sharp corners
or edges, run appliance over cord, or expose cord to
heated surfaces.
■ Do not unplug by pulling on cord. unplug by
grasping plug.
■ Do not run appliance over cord.
■ Do not handle plug or appliance with wet hands.
■ Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts.
■ Do not pick up hot or burning objects such as
cigarettes, matches, or hot ashes.
■ Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc.) or use in the
presence of explosive liquids or vapour.
■ Do not use appliance in an enclosed space filled with
vapours given off by oil base paint, paint
thinner, some moth proofing substances, flammable
dust, or other explosive or toxic vapours.
■ Not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety
■ Young children should be supervised to ensure that they
do not play with the appliance.
www.bissell.com
maintaining the appliance.
■ If the supply cord is damaged, it must be replaced
SAVE THESE
INSTRUCTIONS.
This model is for HOUSEHOLD use only.
IMPORTANT
FOR OPERATION ON A 220-240 VOLT A.C. 50/60 Hz
POWER SUPPLY ONLY.
If your appliance is fitted with a nonrewireable BS
1363 plug it must not be used unless a 13 amp (ASTA
approved to BS 1362) fuse is fitted in the carrier
contained in the plug. (Spares may be obtained from
your BISSELL supplier). If for any reason the plug is cut
off, it must be disposed of, as it is an electric shock
hazard should it be inserted into a mains socket.
3
Product view
Handle
Release Switch
TurboBrush™
(TurboBrush™ Pet
Cord Clip
on select models)
Brush On/Off Switch
Power Switch
Dusting Brush/
Upholstery Tool
Quick Release
Cord Wrap
Stretch Hose
Twist n'
Snap Hose
Connection
Crevice Tool
Dirt Container
Lock 'n
Seal™ Lever
HEPA Media
Post-Motor Filter
Pre-Motor
Filter
Headlight
Hose Clip
Telescoping
Extension
Wand
Hose Grip
Height
Adjustment
Knob
Furniture
Protection
Guard
Powerfoot
caution:
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
4
www.bissell.com
Handle Release
Pedal
Hose Grip
Base
How to use this guide
This user’s guide has been designed to help you
get the utmost satisfaction from your BISSELL
vacuum. You’ll find assembly and operating
instructions, safety precautions, as well as
maintenance and troubleshooting instructions.
Please read this guide thoroughly before
assembling your vacuum cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate
and organize all parts before assembly. Following
this user’s guide will greatly enhance your ability
to get the most performance from your BISSELL
vacuum for many years.
W
arning:
Plastic film can be
dangerous. To avoid
danger of suffocation,
keep away from babies
and children.
Assembly
The only tool you’ll need to assemble your
vacuum cleaner is a Philips head screwdriver.
Attach handle to vacuum
1.
Locate the vacuum handle and remove the
screw packet taped to the base of the handle.
2.
Stand the vacuum upright and slide the base of
the handle firmly into the grooves at the top of
the vacuum body.
Check to be sure the handle is fitted to the
vacuum body. If there is a gap in front, continue
to push firmly until the handle is flush.
Insert the two screws from the screw packet into the
existing holes. Tighten securely with a screwdriver.
3.
4.
2.
4.
Attach vacuum hose and tools
1.
Position the Twist ‘n Snap Hose™ assembly on
the vacuum and line up the tabs on the base of
the hose with the corresponding notches. Turn the
Twist ‘n Snap Hose to the right to lock into place.
2.
Slide the end of the hose grip onto the hose grip
base. Place the hose into the hose clip.
NOTE: The powerfoot will not operate effectively
unless the hose is firmly attached to the base.
1.
2.
www.bissell.com
5
Assembly
3.
Attach vacuum hose and tools continued
3.
Snap the telescoping extension wand,
crevice tool, and combination tool into
storage clips as shown.
4.
The TurboBrush snaps on to the holder on
the front of the handle.
Combination
Tool
Crevice Tool
Place the TurboBrush in the holder by hooking
the bottom onto the tab and pushing the top of
the TurboBrush into place.
Telescoping
Wand
Operation
Power switch/brush switch
TurboBrush™
The power switch is located just below the handle
on the front of the detachable canister. Push the
rocker switch “ON” (I) to vacuum, and “OFF” (O)
when cleaning is complete.
The brush switch is located just below the
handle on the front of the detachable canister
next to the power switch. This switch turns the
rotating brush on and off. The brush switch
should be in the “ON” (I) position for normal
carpet cleaning. You may want to turn the brush
switch “OFF” (O) for bare floor cleaning or other
delicate surfaces.
caution:
Before using your vacuum, make
sure that both filters (Pre-Motor
and Post-Motor) are in place. Do
not operate your vacuum without
these filters.
Tip:
Note: Your BISSELL Lift-Off Multi Cyclonic
vacuum is equipped with a special internal
switch that turns the rotating brush off
whenever the unit is in the Upright position.
Your vacuum features a Quick-Release
Cord Wrap. To remove the Power Cord
quickly and easily, rotate the Upper
Cord Wrap towards floor, and slip Power
Cord from Upper and Cord Wraps..
Handle position
16
6
1.
Upright- For storage and above floor
cleaning with special tools.
2.
Normal Cleaning- Press handle release
pedal once. Use for most household floor
cleaning tasks.
www.bissell.com
1.
Power
2.
Brush
Operation
Tip:
Power height adjustment
Before cleaning under
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
The powerfoot on your vacuum can be
adjusted to clean several floor surfaces.
NOTE: For optimal cleaning performance,
adjust to the lowest practical setting. If
your cleaner is difficult to push, adjust to
the next higher setting.
1.
Place handle in upright position.
2.
Turn height adjustment knob to desired setting.
Lowest Setting – For bare floors.
Medium Settings – For short and medium
pile carpets.
Highest Setting – For plush pile carpet.
NOTE: You may also adjust the setting while
in the normal cleaning position.
1.
Special tools
Your vacuum is not only a powerful floor vacuum
cleaner, it’s also a versatile stairs and above floor
vacuum when you select one of the special tools.
Note: The tools can be used with the
vacuum in the Upright Position or with the
Detachable Canister.
1.
Detach the vacuum hose by grasping the
hose grip and lifting to separate from the
hose grip base.
2.
Attach tools by firmly pushing onto vacuum
hose or telescoping extension wand.
Combination dusting brush/upholstery tool:
Two types of cleaning tools are included in one
attachment. Rotate for desired tool.
■ Use brush side to dust furniture, blinds, books,
lamps, shelves, and baseboards.
■ Use upholstery side for curtains, draperies,
cushions, fabrics.
Crevice tool:
Use in tight narrow spaces.
Telescoping extension wand:
Use with desired attachment for a longer reach. To
extend the wand, twist the collar to “Unlock” position and push away from you. Twist the collar to the
“Lock” position to lock into place. To retract, twist to
unlock, pull toward you and twist to relock.
www.bissell.com
caution:
Always place vacuum cleaner on
floor in its fully Upright Position
and make sure it is locked into
place before removing Canister
or when using tools. Placing the
Lift-Off in its full Upright Position
automatically stops the
rotating brush.
7
Operation
Special tools continued
TurboBrush™ Pet (on select models):
Use for removing dirt and pet hair from stairs,
upholstery, area rugs, and other small areas. Pull
towards you in a raking motion.
Note: TurboBrush Pet is designed to remove pet
hair from upholstered or carpeted surfaces. It
should not be used on pets.
TurboBrush™
Use rotating brush action for small areas such as
stairs and upholstery.
Note: Press gently when using the TurboBrush
to gain maximum cleaning. Too much pressure
could cause the brush to stop rotating.
Stair cleaning tool (select models only):
Use for stairs, area rugs, and other small carpeted
areas. This tool can also be used for bare floors.
Note: The stair cleaning tool does not
store on board.
Deluxe bare floor tool (select models):
Use for bare floors. Swivel head turns to get
into tight spaces and fits under cabinets.
Note: The deluxe bare floor tool does not store
on board.
All items may not be included with your model.
More tools may be available; to order please
refer to page 19­.
Shoulder Strap (select models only)
The Shoulder Strap may be used while cleaning
with the Detachable Canister.
1. To attach the shoulder strap, wrap the Velcro
ends attached to the bottom of the strap
securely around the canister handle as shown.
To obtain maximum strength, overlap the loose
ends completely and press securely in place.
2.
The plastic buckle must be positioned on top of
the canister handle.
3.
The length of the strap may be adjusted as
required for comfort.
1.
Buckle
2.
NOTICE:
While vacuuming, certain
carpets and low humidity
conditions may generate small
static discharges. The discharges
are entirely harmless and are not
associated in any way with the
main power supply.
caution:
To reduce the risk of the shoulder
strap coming loose in operation
follow these instructions.
caution:
Do not press the Release Button
while using the Carrying Handle to
transport the vacuum cleaner. The
Canister could detach causing
the rest of the vacuum to fall.
8
www.bissell.com
Operation
Cleaning with the detachable canister
The detachable canister feature makes it
possible to easily take the powerful cleaning
action of your BISSELL Lift-Off Multi Cyclonic
to stairways, auto interiors, and other
hard-to-reach areas of your home.
Before detaching the canister, your vacuum must
be in its fully upright position. You do not need to
turn off the power first.
1. Press the release button at the top of the
canister handle and lift the canister to remove.
2.
Detach the vacuum hose from the hose grip
base at the back of the canister.
3.
Attach the desired tool(s) to the hose grip at
the end of the Vacuum Hose.
4.
When you’re done, remove the tool(s) and
reconnect the hose to the hose grip base.
5.
Return the canister to the powerfoot by
aligning the “feet” on the front with the
bumps on the foot of the upright vacuum.
Push the canister toward the vacuum frame
until it “clicks” into place.
Power cord storage
When you are done using your vacuum, return it to
the Upright position and store the power cord.
1. Turn vacuum cleaner off (O).
2.
Unplug power cord by grasping the polarized
plug (NOT the cord) and disconnect from outlet.
3.
Loop power cord around cord wraps on side
of the canister.
4.
Clip molded plug to power cord to secure.
1.
caution:
While the vacuum is in use, warm air
is emitted through the Post-Motor
Filter on the back of the Canister.
The bottom of the Canister may
also become warm. When using the
shoulder strap, to avoid discomfort,
position the Canister so that these
parts are not directed towards or
touching your body.
Transporting Cleaner
1.
2.
To move your vacuum cleaner from room to room,
put the Handle in the Upright Position, tilt the
cleaner back on its rear wheels and push forward.
Carrying Handle
1.
2.
The cleaner can also be moved by using
the Carrying Handle on the Detachable
Canister.
www.bissell.com
16
9
Maintenance and care
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
1. Empty the dirt container when the dirt
reaches the “Full” line on the front.
2.
Check the pre-motor filter at least once a
month and clean and replace as needed.
3.
Replace the HEPA media post-motor filter
every six months.
W
ARNING:
To reduce the risk of electric
shock, turn Power Switch
OFF and disconnect plug
from electrical outlet before
performing maintenance or
troubleshooting checks.
NOTE: More frequent filter cleaning may be
necessary if you are vacuuming new carpet,
fine dust, or have allergy concerns.
Follow the instructions on the following pages
to perform these simple maintenance steps.
4.
Allow parts to dry completely before
returning them back into the vacuum.
Tip:
For maximum cleaning
performance, check and
clean or replace all filters
as suggested.
Empty dirt container
The dirt container needs to be emptied when the
dirt reaches the “Full” line on the front of the
container.
1. Unplug cleaner from electrical outlet.
Unlock
2.
Slide the Lock ‘n Seal Lever to the “Unlock” Position
position.
3.
Grasp handle and pull the dirt container
straight out to remove from vacuum.
4.
Empty dirt into garbage container.
5.
Put the dirt container back in the vacuum
and slide the lever to the “Lock” position.
The dirt container may be washed in warm
water with a mild detergent. Make sure it is
completely dry before replacing.
10
Full Line
www.bissell.com
Lock
Position
Maintenance and care
Cleaning the secondary cyclone
1.
Unplug the cleaner from electrical outlet.
1.
The secondary cyclone can be reached by
removing the dirt container, reaching underneath
the upper tank and turning the rim of the frame to
unlock. Pull straight down to remove.
2.
The cyclone and screen may be separated
for cleaning. Simply pull up on the screen to
separate.
3.
The upper tank may also be wiped clean
with a damp cloth.
Cleaning the pre-motor and post-motor filter
1.
Unplug the vacuum from electrical outlet.
2.
The Pre-Motor Filter protects the motor from
dirt particles. It is located in the slide out tray
underneath the Dirt Container. If the filter
becomes dirty, pull out the tray, lift out the filter and clean. This filter may be hand washed
in cold water with mild detergent. Rinse well
and air dry thoroughly before replacing.
3.
The HEPA Media Post-Motor Filter assists in the
filtration process to return clean air to the
room. It is located behind the door on the back
of the cleaner. If the filter becomes dirty, open
the door, remove the filter and replace. The
HEPA Media Filter is not washable.
2.
Pre-Motor Filter
3.
HEPA Media
Post-Motor Filter
W
ARNING:
Do not operate cleaner
with damp or wet
filters or without all
filters in place.
www.bissell.com
11
Maintenance and care
Rotating brush and drive belt maintenance
Check your vacuum cleaner’s rotating floor
brush and drive belt regularly for debris, wear or
damage. Debris can wrap around the brush and
hamper its ability to effectively clean your carpet.
1. Unplug cleaner from electrical outlet.
2.
Remove detachable canister from vacuum cleaner
3.
Recline handle and turn vacuum cleaner over
so bottom side is up.
4.
Remove the six screws as shown with a Phillips
head screwdriver. Lift the brush cover off.
5.
Lift the rotating floor brush to remove. Clean
strings, hair and other debris from the brush,
paying special attention to the brush ends.
6.
Check air passageway for obstructions.
Remove any debris from this area.
7.
Clean debris from the motor pulley and drive
belt areas.
8.
Check drive belt carefully for wear, cuts or
stressed areas. If any damage is present,
discard old drive belt and replace.
9.
Place one end of the new drive belt over motor
pulley and the other end over the brush in the
space between the bristles.
C
aution:
To reduce the risk of injury
from moving parts, turn
off vacuum cleaner and
disconnect Power Plug
from electrical outlet.
4.
6.-8.
Air
Passageway
Motor
Pulley
10. Pull the brush firmly to stretch the drive belt
and place ends of brush down into slots on
sides as shown. Turn brush several times by
hand to center the drive belt.
Drive Belt
11. Reposition brush cover and screws. Tighten
screws securely.
10.
12
www.bissell.com
Maintenance and care
Replace light bulb
1.
Unplug cleaner from electrical outlet.
2.
Remove detachable canister and recline
handle of vacuum.
3.
Using a screwdriver, remove the one screw
as shown and lift off the lens.
4.
Remove the bulb from the socket by grasping
bulb and pulling straight out. Install the new
bulb by pushing it gently into the socket until
the bulb snaps into place.
5.
W
ARNING:
To reduce the risk of electric
shock, turn Power Switch
OFF and disconnect plug
from electrical outlet before
performing maintenance or
troubleshooting checks.
3.
4.
Reposition lens and secure with the one
screw.
TurboBrush maintenance
(TurboBrush™ Pet on select models only)
The TurboBrush should be checked
regularly for clogs or debris wrapping
around the brush roll.
1.
Unplug vacuum from electrical outlet.
2.
If a clog is present or debris is visible, unscrew
the two screws on the back of the TurboBrush to
remove the faceplate and clear any obstructions.
3.
To clean debris from the brush roll, remove the
screw located on the belt cover. Lift the belt
cover. Remove the brush roll from the drive belt
and clean debris.
4.
Reposition the drive belt on the brush roll. Place
ends of brush roll in slots on sides as shown.
Reposition belt cover and secure with shorter
screw. Reposition faceplate and secure with two
longer screws.
www.bissell.com
2.
13
Maintenance and care
Cleaning clogs
4.
Low suction or poor pickup may be due to a clog
in the vacuum cleaner. If you notice a change in
the sound of the motor or a reduction in the
spinning action, check for clogs.
1. Unplug cleaner from electrical outlet.
2.
Empty Dirt Container.
3.
Check Upper Tank for build up or clogs.
4.
Remove the secondary cyclone and check
the suction inlet for a clog.
5.
Grasp the Hose Grip and lift to separate from
the suction opening. Check for a clog in the
Base or the Hose.
6.
Release the Twist n' Snap hose from the
vacuum by turning to the left. Straighten the
hose and unclog with a long, narrow object
such as a broomstick.
7.
Suction
Inlet
5.
If the low suction persists, follow the
instructions for Checking the Rotating Brush
on page 12 and inspect the Air Passageway
for obstructions.
Suction
Opening
7.
Air Passageway
14
www.bissell.com
Maintenance and care
Thermal protector
An internal thermal protector has been designed
into your cleaner to protect it from overheating.
When the thermal protector activates, the main
vacuum motor will stop operating. If this
happens, proceed as follows:
1. Turn the cleaner OFF (O) and unplug from
electrical outlet.
2.
Check the secondary cyclone area, PreMotor Filter and Post-Motor Filter for dirt
accumulation.
3.
Refer to the "Clearing Clogs" section.
4.
When the motor cools for approximately 30
minutes, the thermal protector automatically
resets and cleaning may continue. If the
thermal protector continues to activate after
following the above steps, your cleaner may
need servicing. Call BISSELL Consumer
Services, or visit the website.
C
aution:
To reduce the risk of
injury from moving
parts, turn off vacuum
cleaner and disconnect
Power Plug from
electrical outlet.
Note: The thermal protector controls the
main vacuum motor only, not the brush
motor. If the thermal protector activates,
the brush will continue to operate normally;
however, there will be no suction.
www.bissell.com
15
Troubleshooting
Vacuum cleaner won’t run
W
ARNING:
To reduce the risk of electric
shock, turn power OFF and
disconnect plug from electrical
outlet before performing
maintenance or troubleshooting.
Possible causes
Remedies
1. Power cord not firmly plugged in
1. Check electrical plug
2. Thermal protector activated
2. Allow cleaner to cool for 30 minutes,
see page 15
No power at rotating floor brush
Possible causes Remedies
1. Canister is not securely seated
1. Remove canister and replace, making sure
that it "clicks" into place
2. Brush switch turned to "OFF"
2. Make sure brush switch is in "ON" position
3. Vacuum is in upright position
3. Recline vacuum to operate brush
Vacuum cleaner won't pick up dirt
Possible causes Remedies
1. Incorrect height adjustment
1. Adjust powerfoot to correct height setting
2. Hose not attached to suction opening
2. Grasp hose grip and firmly push onto
the base
3. Crack or hole in hose
3. Check hose and replace if needed
4. Drive belt broken, worn or off motor pulley
4. Reposition or replace drive belt,
see page 12
5. Rotating floor brush bristles worn
5. Replace brush
6. Rotating floor brush jammed
6. Remove brush and clean debris from
brush ends
7. Clog in vacuum
7. Follow instructions for clearing clogs
on page 14
8. Dirt container full
8. Empty dirt container
9. Dirt container or secondary cyclone not installed properly
9. Position correctly and lock into place
10. Filters are dirty
10.Check and clean or replace secondary
cyclone pre-motor and post-motor filters
Vacuum cleaner is difficult to push
16
Possible causes Remedies
1. Incorrect height adjustment
1. Adjust powerfoot to correct height setting
www.bissell.com
Troubleshooting
Visible dirt escaping from cleaner
Possible causes Remedies
1. Dirt container full
1. Empty dirt container
2. Filter or secondary cyclone missing or installed incorrectly 2. Check secondary cyclone, pre-motor and
post-motor filter for correct installation
3. Dirt container installed incorrectly
3. Pull out and re-insert dirt container correctly
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
www.bissell.com
17
BISSELL consumer service
If your BISSELL product should require service:
In the UK, Australia, New Zealand, the Middle East or Africa, call BISSELL Consumer Services at the numbers below
and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact
your local in country distributor for questions, service, or repair.
If you have questions about your warranty or need replacement parts please contact the numbers below.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday 9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
The Boat Yard
105 Straight Road
Old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 0844-888-6644
For Australian inquiries:
Monday - Friday 9 am — 5 pm
BISSELL Australia PTY LIMITED
42 Rocco Dr.
Scoresby, Victoria 3179
Australia
Telephone: 1-800-811-183
For New Zealand inquiries:
Monday - Friday 9 am — 5 pm
Parex Industries Ltd.
5 Tolich Place
Henderson 0610
Auckland
New Zealand
Telephone: 0800-247-735
For Middle East & Africa inquiries:
Sunday - Thursday 8 am — 5 pm
BISSELL Middle East & Africa
P.O. Box 61286
Jebel Ali Free Zone
Dubai
United Arab Emirates
Telephone: 971-4-881-8597
Fax: 971-4-881-8598
For all other inquiries:
Monday - Friday 8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a
warranty claim. See Warranty on page 20 for details.
Please do not return this product to the store.
18
www.bissell.com
Replacement parts –­ BISSELL Lift-Off Multi Cyclonic series
Item
Part No.
1
2
3
4
5
6
7
8
3200Style 8 Drive Belt (2-Pack)
203-1297Standard Headlight Bulb
203-2073
Twist ‘n Snap Hose
203-2085
Brush Roll - Grey (other colors also available)
3290 Style 8 Pre-Motor Filter
3091Style 8 HEPA Media Post-Motor Filter
203-2445Secondary Cyclone
203-2444Screen
Part Name
1
2
3
4
5
6
7
8
Additional accessories
These items are available for purchase as accessories for your BISSELL Lift-Off Multi Cyclonic
To purchase call 1-800-237-7691 or visit www.bissell.com.
Item
Part No.
1
2
3
4
5
6
7
8
203-1063
Crevice Tool
203-1399
Pet TurboBrush (Available on Select Models)
203-1099
Dusting Brush/Upholstery Tool
203-2302
TurboBrush
203-6624Stair Cleaning Tool (Available on Select Models)
203-6625
Telescoping Extension Wand
203-2081
Deluxe Bare Floor Tool (Available on Select Models)
203-5542Shoulder Strap (Available on Select Models)
Part Name
1
2
3
4
5
6
7
8
www.bissell.com
19
Warranty - BISSELL Lif-Off
™
Multi Cyclonic Series
This warranty gives you specific legal rights, and you may also have other rights which may vary from country
to country. If you need additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or
contact your local in country distributor.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with
new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the
original purchaser, for one year any defective or malfunctioning part do to manufacturers defect.
This warranty applies to product used for personal, and not commercial or rental service. This warranty does
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday
9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
The Boat Yard
105 Straight Road
Old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 0844-888-6644
For New Zealand inquiries:
Monday - Friday 9 am — 5 pm
Parex Industries Ltd.
5 Tolich Place
Henderson 0610
Auckland
New Zealand
Telephone: 0800-247-735
For Australian inquiries:
Monday - Friday 9 am — 5 pm
BISSELL Australia PTY LIMITED
42 Rocco Dr.
Scoresby, Victoria 3179
Australia
Telephone: 1-800-811-183
For all other inquiries:
Monday - Friday 8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES
EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE
BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS
DESCRIBED ABOVE.
20
©2009 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 110-4162
Rev 9/09
Visit our website at:
www.bissell.com
www.bissell.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising