Chevrolet | 2007 Yukon Denali | With DVD Player

With DVD Player
2007 Chevrolet Avalanche, Tahoe, Suburban and GMC Yukon,
Yukon XL, Yukon Denali, Yukon XL Denali
Navigation Manual M
Overview ......................................................... 3
Overview ................................................... 4
Features and Controls ................................. 15
Features and Controls ............................. 16
Navigation Audio System ............................
Navigation Audio System .........................
Voice Recognition ........................................
Voice Recognition ....................................
Index .............................................................
59
60
85
86
91
1
The information in this manual supplements the
owner manual. This manual includes the latest
information available at the time it was printed. We
reserve the right to make changes in the product
after that time without notice. For vehicles first sold
in Canada, substitute the name General Motors
of Canada Limited for Chevrolet Motor Division or
GMC whenever it appears in this manual.
Keep this manual with the owner manual in the
vehicle, so it will be there if it is needed. If
the vehicle is sold, leave this manual in the
vehicle.
GENERAL MOTORS, GM, the GM Emblem,
CHEVROLET, the CHEVROLET Emblem, and the
names TAHOE, SUBURBAN, and AVALANCHE,
GMC, the GMC Truck Emblem, and the names
YUKON and DENALI are registered trademarks of
General Motors Corporation.
Litho in U.S.A.
Part No. 15825631 A First Printing
2
©
Canadian Owners
For Canadian owners that would like to obtain a
French language manual, see “Canadian Owners”
in the Index of your vehicle’s owner manual.
2005 General Motors Corporation. All Rights Reserved.
Section 1
Overview ..........................................................4
Navigation System Overview ..........................4
Overview
Getting Started ...............................................6
Cleaning the Video Screen ...........................13
3
Overview
Navigation System Overview
Screen Shown with Map Disc Inserted
4
A. CD/DVD Slot. See CD Player on page 70 and
DVD Player on page 77 for more information.
B. FULL MAP Touch Screen Button. See
“NAV” under “Hard Keys” under Using the
Navigation System on page 16 for more
information.
C. North Up/Heading Up Symbol. See Symbols on
page 20 for more information.
D. O(Power/Volume) Knob. See Navigation
Audio System on page 60 for more information.
E. No GPS Symbol. See Symbols on page 20
for more information.
F. NAV (Navigation) Key. See “Hard Keys” under
Using the Navigation System on page 16
for more information.
G. Straight Line to Distance Symbol. See Symbols
on page 20 for more information.
H. DEST (Destination) Key. See Destination on
page 27 for more information.
I. Map Scale. See “Map Scales” under Maps on
page 18 for more information.
J. RPT (Repeat) Key. See “Hard Keys” under
Using the Navigation System on page 16
for more information.
K. FAV (Favorite) Key. See “Storing Preset
Stations” under Navigation Audio System on
page 60 for more information.
L. V (Zoom In) Touch Screen Button. See “Map
Scales” under Maps on page 18 for more
information.
M. Mark Touch Screen Button. See “Adding
Destinations to the Address Book” under
Destination on page 27 for more information.
N. Source (AM, FM, XM, CD, etc.) Touch
Screen Button. See Navigation Audio System
on page 60 for more information.
O. Z (CD/DVD Video/Audio Eject) Key. See CD
Player on page 70 and DVD Player on
page 77 for more information.
P. Auxiliary Jack. See Auxiliary Devices on
page 84 for more information.
Q. Clock Touch Screen Button. See Configure
Menu on page 43 for more information.
R. Map DVD Slot. See “Installing the Map DVD”
under Maps on page 18 for more information.
S. f (Tune/Sound) knob. See Navigation
Audio System on page 60 for more information.
5
T. AUDIO Key. See Navigation Audio System on
page 60 for more information.
U. MENU Key. See Configure Menu on page 43
for more information.
V. ¨SEEK Key (Next). See Navigation Audio
System on page 60 for more information.
W. U (Zoom Out) Touch Screen Button. See
“Map Scales” under Maps on page 18 for
more information.
X. ©SEEK Key (Previous). See Navigation Audio
System on page 60 for more information.
Y. POI (Point of Interest) Touch Screen Button.
See “Displaying Points of Interest (POI) on the
Map Screen” under Symbols on page 20 for
more information.
Getting Started
Before you begin to operate the navigation system,
read this manual thoroughly to become familiar with
it and to understand how the system works.
Keeping your mind on the drive is important for safe
driving. See “Defensive Driving” in the Index of your
vehicle’s owner manual for more information. Get
familiar with your vehicle’s navigation system so
you can use it with less effort and take full
advantage of its features. Your navigation system
includes not only navigation, but also audio
functions. While your vehicle is parked:
• Familiarize yourself with all of its controls: hard
keys on the faceplate and touch-sensitive
screen buttons.
• Familiarize yourself with its operation.
• Set up your audio by presetting your favorite
stations, setting the tone, and adjusting the
speakers. Then, when driving conditions
permit, you can tune to your favorite stations
using the presets and steering wheel controls
(if equipped).
• Set up the navigation features that can only be
done before you begin driving, such as entering
an address or a preset destination.
Entering a destination or alphanumeric text
requires many steps, so you can only perform
these operations when the vehicle is in PARK (P).
6
You will notice that touch-sensitive screen buttons
leading to the alphanumeric keyboard are
dimmed out while driving.
Other functions may also be locked out while
driving and they too will appear grayed out on the
screen — but all functions are available when
parked. Some functions can be performed while
driving, as long as you can do so without diverting
too much of your attention from your driving.
{CAUTION:
This system provides you with a far
greater access to audio stations and
song listings. Giving extended attention
to entertainment tasks while driving can
cause a crash and you or others can
be injured or killed. Always keep your
eyes on the road and your mind on the
drive — avoid engaging in extended
searching while driving.
{CAUTION:
Looking at the moving map on the
navigation screen frequently or for too
long while driving can cause a crash and
you or others can be injured or killed.
Keep your eyes and mind on the road and
avoid looking too long or too often at the
moving map on the navigation screen.
Use the voice guidance directions
whenever possible.
The navigation system allows you to do the
following:
• Plan a route with provided turn-by-turn route
and map guidance with voice prompts.
• Select a destination using various methods
and choices.
• Receive RDS broadcast announcements.
The information in the system may not always be
complete. Road conditions such as prohibited
turns, detours, and construction zones, change
frequently.
7
It is important to consider whether you can follow
the directions given by the system for the
current conditions.
When getting started you may set the navigation
system to your preference using various
options. To do so, reference the following topics:
Language — English/Metric
To change the language of the navigation screens,
see “Driver Information Center, DIC Vehicle
Customization” in the Index of your vehicles
owner manual.
To change the navigation screens from English
or metric, see “Driver Information Center, DIC
Operation and Displays” in the Index of your
vehicles owner manual.
Storing Radio Station Presets
Each time the vehicle is started and the navigation
system is turned on, the Caution screen or the
previous active screen will appear dependent
on system power off time. If the Caution
screen appears, touch OK to load the map
DVD information. If OK is not selected, all hard
keys except for NAV (Navigation) and DEST
(Destination) can be accessed. Once the NAV or
DEST hard keys are pressed, this Caution
screen will appear and OK must be pressed to
load the map DVD information from the map disc.
8
To set preset radio stations, do the following:
1. Press the O(power) knob to turn the
system on.
2. Press the AUDIO hard key and select the
desired band (AM, FM1, FM2, XM1, or
XM2 (if equipped)).
3. Use the f (tune) knob or the SEEK arrows
to tune to the desired station.
4. Press and hold one of the five preset screen
buttons, at the bottom of the screen, until you
hear a beep or see the station displayed
on the selected preset button.
Setting the Search Area, Entering an
Address and Point of Interest, and
Storing Preset Destinations
5. Repeat the steps for each preset.
Before entering an Address, Point of Interest,
Home, or Preset Destination, select the
appropriate region that contains the final
destination. Your vehicle must be in PARK (P)
to perform this operation.
See “Storing Preset Stations” under Navigation
Audio System on page 60 for more information.
Setting the Time
To set the time, do the following:
1. Press the clock touch screen button located
in the upper right corner of the screen.
2. Press the SET screen button.
3. Press the Hours and Minutes − (minus) and
+ (plus) signs to decrease and to increase
the time. See “Setting the Time” under
Configure Menu on page 43 for more
information.
Setting the Search Area
To set the search area, do the following:
1. Press the O(power) knob to turn the
system on.
2. Insert the DVD map disc. See “Installing the
Map DVD” under Maps on page 18 for more
information.
3. A caution may appear. Touch the OK screen
button to proceed.
If the radio is already on with a map disc
inserted, press the DEST hard key.
4. Press the Change Search Area screen button.
5. Select the appropriate region numbered
screen button that contains your final
destination.
9
The system will return to the Destination Entry
menu. See Destination on page 27 for more
information.
Entering an Address
To set a destination by entering a street address,
do the following:
1. Press the O(power) knob to turn the
system on.
2. Insert the DVD map disc. See “Installing the
Map DVD” under Maps on page 18 for more
information.
3. A caution may appear. Touch the OK screen
button to proceed.
If the radio is already on with a map disc
inserted, press the DEST hard key.
4. Press the 6 Address Entry screen button.
5. Select the street screen button and start
entering the street name.
Do not enter directional information or street
type, and use the space symbol screen button
( U ) between street or city names. For
example, the street name N. Royal Oak Rd.
10
should be entered as royal U oak. Use the
backspace ( V ) screen button if an incorrect
character has been entered.
If five or less names are available, a list will
display. If more than five are available,
there will be a screen button with a number in
it, it represents the number of available
streets. Select this button to view the list.
6. Select the street name with the correct prefix
from the list (Dr., Ln., St., etc.).
7. Once a street has been selected the City
name category will automatically be selected
for entry.
If five or less cities are available for the selected
street, the system will display the list of cities.
If more than five cities are available the system
will display the alpha keyboard. Start entering
the city name. If five or less names are
available, a list will display. If more than five are
available, there will be a screen button with a
number in it, it represents the number of
available cities. Select this button to view the
list and select a city.
8. Once a city has been selected, the numeric
keyboard will display, allowing you to enter
the house number. The system will display the
house number range that is available for
the street.
9. Select the Go screen button. A map screen,
with the destination marked, will appear.
10. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
11. Select the Start Guidance screen button.
You are now ready to start your route.
See “Address Entry ” under Destination on
page 27 for more information.
Entering a Point of Interest (POI)
To set a destination by entering a Point of
Interest (POI), do the following:
1. Press the O(power) knob to turn the
system on.
2. Insert the DVD map disc. See “Installing the
Map DVD” under Maps on page 18 for more
information.
3. A caution may appear. Touch the OK screen
button to proceed.
If the radio is already on with a map disc
inserted, press the DEST hard key.
4. Press the i Point of Interest screen button.
5. Enter the specific title of the POI in the
POI name space (i.e. Washington Monument).
If five or less names are available, a list will
display. If more than five are available,
there will be a screen button with a number
in it, it represents the number of available
POIs. Select this button to view the list.
6. Select the Go screen button. A map screen,
with the destination marked, will appear.
7. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
8. Select the Start Guidance screen button.
You are now ready to start your route.
See “Point of Interest (POI)” under Destination
on page 27 for more information.
11
Storing Preset Destinations
1. Press the O(power) knob to turn the
system on.
2. Insert the DVD map disc. See “Installing the
Map DVD” under Maps on page 18 for more
information.
3. A caution may appear. Touch the OK screen
button to proceed.
If the radio is already on with a map disc
inserted, press the DEST hard key.
4. Enter a destination. See Destination on
page 27 for information on how to enter
a destination.
5. Press the Mark screen button from the map
screen to add the current final destination as
a preset destination.
The address book screen will appear.
6. Select the Name screen button. An
alpha-keyboard will display. Enter the name.
7. Press and hold one of the screen buttons
at the bottom of the screen until a pop-up
confirmation displays.
12
The name will appear in that preset destination
screen button and is now available to select
from the Destination Entry screen. See “Using
Your Stored Preset Destinations” next in
this section to select it as a destination.
See “Adding or Changing Preset Destinations”
under Destination on page 27 for information
on how to add preset destinations.
Using Your Stored Preset Destinations
These destinations are available for selection
while driving.
1. Press the O(power) knob to turn the
system on.
2. Insert the DVD map disc. See “Installing the
Map DVD” under Maps on page 18 for more
information.
3. A caution may appear. Touch the OK screen
button to proceed.
If the radio is already on with a map disc
inserted, press the DEST hard key.
4. Select one of the available preset destination
screen buttons. A map, screen with the
destination marked, will appear.
5. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
6. Select the Start Guidance screen button.
You are now ready to start your route.
See “Preset Destination” under Destination on
page 27 for more information.
Canceling Guidance
Guidance will be canceled once you arrive at your
final destination. To cancel guidance prior to
arrival at the final destination, do the following:
1. Press the DEST hard key.
2. Press the Cancel Guidance screen button.
Guidance Volume
To adjust the volume of voice guidance prompts,
do the following:
1. Press the MENU hard key to enter the menu
options, then press the MENU key repeatedly
until Nav is highlighted.
2. Press the > Voice Prompt screen button.
3. Press the + (plus) or – (minus) screen buttons
to increase or to decrease the volume of the
voice prompts.
See “Voice Prompt ” under Configure Menu on
page 43 for more information.
Cleaning the Video Screen
When cleaning the video screen, use only a soft
clean cotton cloth dampened with clean water.
13
✍ NOTES
14
Section 2
Features and Controls
Features and Controls ...................................16
Using the Navigation System .......................16
Maps ...........................................................18
Symbols .......................................................20
Destination ...................................................27
Configure Menu ...........................................43
Rear Vision Camera .....................................51
Global Positioning System (GPS) .................56
Vehicle Positioning .......................................56
Problems with Route Guidance ....................57
If the System Needs Service ........................58
Ordering Map DVDs .....................................58
Database Coverage Explanations .................58
15
Features and Controls
Using the Navigation System
This section presents basic information needed to
operate the navigation system.
Use the hard keys located on the navigation
system along with the available touch-sensitive
screen buttons on the navigation screen to operate
the system. See Navigation System Overview
on page 4 for more information.
Once the vehicle is moving, various functions will
be disabled to reduce driver distractions.
Hard Keys
The following hard keys are located on the
navigation system:
O (Power/Volume): Press this knob to turn the
system on and off. Turn the knob to increase
or decrease the volume to the audio system.
If your vehicle has the Rear Seat Entertainment
(RSE) and Rear Seat Audio (RSA), press and hold
this knob for more than two seconds to turn off
the navigation system, the RSE, and RSA.
16
f (Tune/Speaker Adjustment): Press this knob
to access the Sound screen to adjust bass,
midrange, treble, and equalization or Digital Signal
Processing (DSP), if the vehicle has the Bose®
sound system. Turn the tune knob to go to the next
or previous radio station. See Navigation Audio
System on page 60 for more information.
Z (CD/DVD Eject): Press the eject button to
eject CDs or DVDs.
NAV (Navigation): Press this key to view your
vehicle’s current position on the map screen. Each
press of this key will cycle through Full Map and
the tab that displays the current audio source (AM,
FM, CD, etc.). Full Map displays the screen in
full map view. Selecting the audio tab will split the
screen between the map screen and the current
audio source screen menu. See “Audio” under
Navigation Audio System on page 60 for
more information.
DEST (Destination): Press this key to access
the Destination Entry screen to plan a destination
or to change the search area. See Destination
on page 27 for more information.
RPT (Navigation Repeat): Press this key to
repeat the last voice guidance prompt.
FAV (Favorite): Press this key to access the
preset stations. See “Storing Preset Stations”
under Navigation Audio System on page 60 for
more information.
Touch-Sensitive Screen Buttons
Touch-sensitive screen buttons, or screen buttons,
are located on the screen. When a screen
button has been selected, a beep will sound.
Screen buttons are highlighted when a feature
is available.
AUDIO: Press this key to access the full Audio
screen to change AM, FM, XM™ Satellite
Radio Service (if equipped), CD, DVD
(if equipped), and auxiliary input. See “Audio”
under Navigation Audio System on page 60
for more information.
Alpha-Numeric Keyboard
MENU: Press this key to adjust features for
sound, radio, navigation, and the display. See
Configure Menu on page 43 for more information.
All characters are touch-sensitive screen
buttons. Touch a character to select it.
¨ SEEK / © SEEK: Press the seek arrows
A-Y (Accent Alphabet): Select this screen button
to select letters with accent symbols. This button
may toggle to A-Z.
to seek and scan radio stations, to seek tracks
on a CD, and to seek chapters on a DVD.
See Navigation Audio System on page 60,
CD Player on page 70, and DVD Player on
page 77 for more information.
Letters of the alphabet, symbols, punctuation,
and numbers, when available, will display on the
navigation screen as an alpha or numeric
keyboard. The alpha keyboard will display when
the system requires entry of a city or street name.
A-Z (Alphabet): Select this screen button to
select letters from the alphabet. This button may
toggle to A-Y.
0-9 (Numbers): Select this screen button to
select numbers.
17
U (Space): Select the space screen button to
enter a space between characters or the words
of a name.
q (Backspace): Select the backspace screen
button if an incorrect character has been selected.
To make name selections easier, the system
will only highlight the characters that can follow
the last one entered. For example, if a Z is
entered, a T may not be available for selection.
If a name does not display after entry, it may need
to be entered differently, the map DVD disc may
not contain that information, or the correct
search area has not been selected. See Database
Coverage Explanations on page 58 for more
information or Destination on page 27 to change
the search area.
Maps
This section includes basic information needed
to know about the map database.
Regional Maps
The maps are stored on a DVD. The 48 contiguous
United States and portions of Canada are
contained on one disc.
If a regional map does not contain a specific city,
the map DVD may not contain the city or it
may have been misspelled when entered.
Refer to the Navigation System Map Disc manual
to view a detailed explanation of map coverage
and detailed city lists in each region. This manual
will be inside the map DVD case when the
vehicle is delivered from the factory.
Installing the Map DVD
When your vehicle is delivered from the factory,
the dealer may have installed the map DVD. If the
map DVD was not installed, use the following
directions to load it:
Read the following steps completely before
operating this feature.
1. Turn the ignition on.
2. Press the O(power) knob to turn the
navigation system on.
18
3. Touch the OK screen button to agree to the
Caution screen.
Map Adjustments
The system allows you to adjust the scale of
view on the map. Also, as you drive, the map
will scroll automatically based on the direction
of travel.
Map Scales
4. Touch the Insert Map Disc screen button. The
screen will tilt to access the map DVD slot.
5. Load the map DVD partway into the slot. The
system will pull it in.
6. Once the map DVD is loaded, touch the
Close screen button. The screen will close.
V / U (Zoom In/Zoom Out): Touch the zoom in
or out screen buttons or the scale on the bar to
change the level of map detail. The scale will
appear on the screen once the zoom in or zoom
out screen buttons are selected. The system
will adjust the map accordingly. The scale of a
map can range from 150 ft. (45 m) to 250 mi.
(402 km). To change from English or metric, see
“Driver Information Center, DIC Operation and
Displays” in the Index of your vehicle’s owner
manual.
19
Scrolling the Map
Touch anywhere on the
map screen and the
scroll symbol will
appear. Use this feature
to scroll across the map.
Move your finger in any direction on the map
screen and the map will continue to scroll in
that direction until you remove your finger.
If scrolling while your vehicle is in PARK (P),
the system will scroll initially at a slower rate.
It will increase if you continue touching the
map screen.
If scrolling while your vehicle is in motion, you
have one scroll speed and a limited distance to
scroll. You have to keep touching the map screen
to scroll for a longer distance.
20
If you have used the scroll feature to scroll the
map and your vehicle icon becomes lost, press
the NAV (Navigation) key to return to the current
vehicle location on the map.
You can use the scroll feature on the map to
set a destination. See “Pick from Map” under
Destination on page 27 for more information.
When scrolling on the map without a planned route,
press the GO screen button to calculate the route
from your current position to the destination mark.
Symbols
The following symbols are the most common
symbols that will appear on a map screen.
Your vehicle is shown
as this symbol. It
indicates the current
position and heading
direction of your vehicle
on the map.
The destination symbol
will appear on the map,
after a route has
been planned, marking
your final destination.
The waypoint symbol
will display on the
map after a waypoint
has been added to
your route.
The waypoint symbol will be numbered from
one through three depending on how many
intermediate waypoints have been set.
The distance to
destination symbol
indicates the distance to
your final destination.
This symbol only appears when time is not
available or when you are scrolling on the map.
The distance and time
to destination symbol
indicates the distance
and the estimated
time remaining to your
final destination or
arrival time, depending
on the option selected.
21
The straight line to
distance symbol
indicates the
straight-line distance
to your destination.
This symbol will appear before you start driving on
the route or if you are on a road where navigation
guidance cannot be given.
The north up symbol
indicates the map with
North Up, known as
North Up mode.
While in North Up mode, the vehicle icon will
follow the north direction on the map regardless of
which direction the vehicle is traveling. Select
this screen symbol to switch between North Up
and Heading Up modes.
22
The heading up symbol
indicates the map with
the vehicle travel
direction up, known as
Heading Up mode.
The shaded triangle indicates the North direction.
While in Heading Up mode, the direction your
vehicle is traveling will always be at the top of the
map screen. The vehicle icon will always be
headed in the direction your vehicle is traveling.
Select this screen symbol to switch between
Heading Up and North Up modes.
The No GPS symbol
will appear when your
vehicle is not receiving
a Global Positioning
System (GPS) satellite
signal.
Displaying Points of Interest (POI) on the
Map Screen
Touch anywhere on
the map to display the
POI (Point of Interest)
screen button.
See Global Positioning System (GPS) on page 56
for more information.
Select the MARK screen
button to store the
location on the screen
in your address book.
Select the POI screen button to display or
delete POI icons from the map. Displaying
POI icons on the map let you know where POIs
(i.e. restaurants, gas stations, etc.) are located.
The system will automatically store the point in the
address book. See “Adding Destinations to the
Address Book” under Destination on page 27 for
more information.
23
This screen will appear after selecting the POI
screen button.
More: Select this screen button to view more POI
categories.
Select one of the POI categories to display or to
delete POI icons from the map screen. Once
a category has been selected, the POI icon will
display at the top of the screen. Five categories
can be selected to display on the map screen.
When a category is selected those POI icons
will display on the map. Press the POI screen
button again to add more POI icons.
POI Close to: Once a category has been
selected, select this screen button to display
the list of available POIs for the selected POI
categories. The list provides the POI icon,
the name, the direction, and the distance to
the POI from your vehicles current position.
Use the scroll arrows to move up and down
the list. Use the Sort by DIST. (distance), Icon,
Name, and, on Route as desired.
24
Go: Press this screen button, next to the desired
POI, to make this POI a destination or a waypoint.
List all Categories: Select this screen button to
list all POIs sorted alphabetically.
Select a POI name to receive information about
the POI. From this screen you can select: Add to
Address Book, Go, or Map.
Clear: To delete a category, do one of the
following:
• To delete the last added POI category, select
the Clear screen button.
• To delete a specific POI category:
1. Select the category.
2. Select the subcategory.
3. A pop-up confirmation will display.
Select the Delete screen button,
the map screen will display with that
POI category deleted.
Add to Address Book: Press this screen button
to add this POI to the address book. See “Nav”
under Configure Menu on page 43 for information
on editing address book entries.
Go: Press this screen button to make this POI a
destination or a waypoint.
Map: Press this screen button to display the map
showing the location of the POI.
Show: Select this screen button to update the
map screen and the list once a category has been
selected.
Show POI: Select ON to display the POI icons
on the map screen. Select OFF to remove the
POI icons from the map screen.
Clear All: Select this screen button to clear all
selected POI categories. A pop-up confirmation will
display. Select the Delete screen button, the
map screen will display with all POI categories
deleted.
25
Driving on a Route
When a destination has been routed and you are
driving on route, the map screen will automatically
display the next maneuver.
This next maneuver
pop-up will display the
next maneuver direction
and how many miles
or kilometers you
are from it.
When you are approximately 1/2 mi. (.08 km) from
the next maneuver, the screen will display the
name and a detailed view of the next maneuver.
Auto Reroute
When your destination is set and you are off the
planned route, the system will automatically plan a
new route and begin to reroute. You will be able
to see the new route highlighted on the screen.
26
Traveling Across Regions
Destination
If you plan to drive across many states, you may
have to change the region selected to represent
the area you are traveling to. To change the
region, do one of the following:
• Change the selected region in the search
area when you get closer to your destination.
See Destination on page 27 or,
• Change the selected region in the search
area when entering your destination and
route settings. See Destination on page 27.
For example, if you were traveling from
Michigan to Florida, change the region
currently selected in the search area to
Florida. Enter a destination in Florida
under the Destination Entry menu.
Press the DEST key to access the Destination
Entry screen. From this screen, you can
select from several options to plan a route by
entering destination points.
27
Search Area
The Destination Entry screen allows you to select
the area included in the search for your destination.
A map that divides the 48 contiguous United States
and a part of Canada into 11 regions is displayed.
Before selecting a method of destination entry,
review the search area map to make sure your
destination is located in the highlighted region.
Touch the Change Search Area screen button
to view the Search Area screen. Touch the
numbered screen button to the left of the search
area map that corresponds with the numbered
region and to view a list of states included in
the region selected. The selected area will
be highlighted on the map. Touch the down arrow
to select CAN (Canada). Touch the back screen
button to return to the Destination Entry screen
and to store the selected region.
To enter a destination, choose from one of the
following destination entry methods:
Address Entry
6 Address Entry: The address entry destination
method allows you to enter an address by providing
the system with a city name or a street name.
28
If using the alpha keyboard, finish entering the
city name. If five or less names are available,
a list will display. If more than five are
available, there will be a screen button with a
number in it, it represents the number of
available cities. Select this button to view the
list and select a city.
To enter a destination by entering the city name
first, do the following:
1. Press the DEST hard key.
2. Select the 6 Address Entry screen button.
3. Select the City name button.
4. Enter the city name or touch the Last 5 Cities
screen button.
The Last 5 Cities screen will display a list of
the last five city names that had been entered.
Select a city from the list and it will appear
in the City name area.
5. Once a city has been selected the Street
name category will automatically be selected
for entry.
Start entering the street name. If five or less
names are available, a list will display. If more
than five are available, there will be a screen
button with a number in it, it represents the
number of available streets. Select this button
to view the list.
6. Select the street name with the correct prefix
(Dr., Ln, St., etc.) from the list.
7. Once a street has been selected, the numeric
keyboard will display, allowing you to enter
the house number. The system will display the
house number range that is available for
the street.
8. Select the Go screen button. The map screen,
with the destination marked, will display.
29
9. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
10. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
To enter a destination by entering the street name
first, do the following:
1. Press the DEST hard key.
2. Select the 6 Address Entry screen button.
3. Select the Street screen button and start
entering the street name.
If five or less names are available, a list will
display. If more than five are available,
there will be a screen button with a number
in it, it represents the number of available
streets. Select this button to view the list.
4. Select the street name with the correct prefix
from the list (Dr., Ln., St., etc.).
30
5. Once a street has been selected the City
name category will automatically be selected
for entry.
If five or less cities are available for the selected
street, the system will display the list of cities.
If more than five cities are available the system
will display the alpha keyboard. Start entering
the city name. If five or less names are
available, a list will display. If more than five are
available, there will be a screen button with a
number in it, it represents the number of
available cities. Select this button to view the
list and select a city.
6. Once a city has been selected, the numeric
keyboard will display, allowing you to enter
the house number. The system will display
the house number range that is available
for the street.
7. Select the Go screen button. The map screen,
with the destination marked, will display.
2. Select the 6 Address Entry screen button.
5. Once a street has been selected the Cross
Street screen button will become available.
Select the Cross Street button and start
entering the cross street name.
If five or less names are available, a list will
display. If more than five are available, there will
be a screen button with a number in it, it
represents the number of available cross
streets. Select this button to view the list.
6. Select the street name with the correct prefix
from the list (Dr., Ln., St., etc.). An Information
screen will automatically display.
3. Select the Street screen button and start
entering the street name.
If five or less names are available, a list will
display. If more than five are available,
there will be a screen button with a number
in it, it represents the number of available
streets. Select this button to view the list.
4. Select the desired street name with the
correct prefix from the list (Dr., Ln., St., etc.).
7. Select the Go screen button. The map screen,
with the destination marked, will display.
8. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
9. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
8. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
9. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
To enter a destination by entering a cross street,
do the following:
1. Press the DEST hard key.
31
Point of Interest (POI)
The Point of Interest (POI) destination entry
method allows you to select a destination from
the POI list.
i Point of Interest: Touch this screen button
to access the Point of Interest (POI) screen. From
this screen you have two options to select/enter
a destination; enter the name using the alpha
keyboard or select a category from the category list.
32
To use the point of interest destination entry
method by entering the name, do the following:
1. Press the DEST hard key.
2. Select the i Point of Interest screen button.
3. Enter the POI name.
If five or less names are available, a list will
display. If more than five are available,
there will be a screen button with a number
in it, it represents the number of available
POIs. Select this button to view the list.
4. Select the Go screen button next to the POI.
The map screen, with the destination marked,
will display.
5. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
6. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
To use the point of interest destination entry
method by selecting a category, do the following:
1. Press the DEST hard key.
2. Select the i Point of Interest screen button.
3. Select the Browse POI screen button to view
the list of POI categories.
4. Select a category, and then a sub-category.
The system will display available POI names in
the selected sub-category or if the list is too
long the system will display the alpha keyboard.
If the alpha keyboard is displayed, enter the
POI name until a list of available POIs appear.
There is a screen button with a number in it, it
represents the number of available POIs. Select
this button to view the list and select the POI.
5. Select the Go screen button next to the POI.
The map screen, with the destination marked,
will display.
6. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
7. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
Previous Destination
The previous destination entry method allows you
to select a destination from a list of previous
destination points.
7 Previous Destination: Touch this screen
button to access the Previous Dest. screen.
The system will store up to 100 points that have
been previously entered. As new destinations
are entered, the system will automatically delete
the oldest destinations and add the new
destinations.
33
To use the previous destination entry method,
do the following:
1. Press the DEST hard key.
2. Select the 7 Previous Destination screen
button.
3. Select a previous destination from the list.
Use the arrow to the right of the destination
to view the entire destination name as
necessary. Use the scroll arrows to the left
to scroll through the list.
4. Select the Go screen button next to the
destination. The map screen, with the
destination marked, will display.
5. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
6. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
34
Address Book
The address book entry method allows you to
select a destination by selecting an address that
has been stored in your address book.
* Address Book: Touch this screen button to
access the Address Book screen. From this screen
you can select an address that already exists as
the destination.
To use the address book entry method, do the
following:
1. Press the DEST hard key.
2. Select the * Address Book screen button.
A list of your address book addresses will
display.
3. Select the Go screen button next to the
destination. The map screen, with the
destination marked, will display.
4. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
5. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
See “Adding Destinations to the Address
Book” later in this section.
Pick from Map
This map destination entry method allows you to
select a destination by scrolling on the map.
Pick from Map: Touch this screen button to enter
the pick from map destination entry method.
35
To use this destination entry method, do the
following:
1. Press the DEST hard key.
2. Select the Pick from Map screen button.
A map screen will display with the scrolling
symbol.
3. Use the V / U (zoom in/out) screen buttons
and touch on the map to find the area that
you would like to select as your destination.
Pressing/holding and dragging your finger
on the map will activate fast scrolling.
4. Press/touch once on the area that you would
like to set as your destination.
The map screen will display the address
information.
5. Select the Go screen button. The map screen,
with the destination marked, will display.
6. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
7. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
36
Map Coordinates
The coordinates destination entry method allows
you to select a destination by entering latitude and
longitude coordinates.
Map Coordinates: Touch this screen button to
access the Coordinates screen.
To use the coordinates destination entry method,
do the following:
1. Press the DEST hard key.
2. Select the Pick from Map screen button.
3. Select the Map Coordinates screen button.
4. Touch N (north) or S (south) next to
Lat. (latitude) to enter the direction of
the latitude coordinate. Enter the numeric
portion of the latitude coordinate.
5. Touch E (east) or W (west) next to Long.
(longitude) to enter the direction of the
longitude coordinate. Enter the numeric
portion of the longitude coordinate.
6. Once both coordinates are entered, select
the OK screen button. The map screen,
with the destination marked, will display.
7. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
Preset Destination
The preset destination entry method allows you
to set a destination by selecting from one of
five previously stored destinations. Besides
voice tagged destinations, these are the only
destinations available to set while the vehicle is
moving. If a destination is not set for one of
the screen buttons, the button will be dimmed and
not available for use. See “Adding or Changing
Preset Destinations” later in this section for more
information on how to add a preset destination.
8. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
37
To use the preset destination entry method,
do the following:
1. Press the DEST hard key.
2. Select the desired preset destination screen
button. The screen buttons are labeled with
the name that was selected for the destination
when it was stored. The map screen, with
the destination marked, will display.
3. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
4. Select the Start Guidance screen button.
You are now ready to start your route.
See “Getting Started on Your Route” later
in this section for more information.
38
Getting Started on Your Route
Once you have entered a destination there are
several functions that can be performed. Press the
DEST hard key to access the Route screen.
Turn List
Turn List: Touch this screen button to view the
list of turn maneuvers for the entire route and
to avoid turns on the route.
Q / R (Scroll Arrows): Touch the up and down
arrow screen buttons to scroll through the list
of maneuvers.
Avoid: Touch this screen button, next to the
adjacent street name, to avoid the maneuver.
The map screen will display. Select the Fastest,
Shortest, or Other screen buttons. Press the Start
Guidance screen button. The route will re-calculate
without the selected avoided street.
Avoid List: Select this screen button to cancel an
avoided turn. The list of selected avoided turns
will display. Select the turn to cancel the turn from
being avoided.
Route Preview: Select this screen button to
preview the entire route in either direction.
t(Reverse Skip): Select this screen button to
go back to the start point or previous waypoint.
q / r(Reverse Scroll): Select this screen
button to scroll to the start point or previous
waypoint. This button will toggle between slow
and fast speed.
39
j(Pause): Select this screen button to pause
Add Waypoint
the route preview, while in reverse or fast forward
scroll.
r/ [(Fast Forward Scroll): Select this screen
button to scroll to the next waypoint or to the
final destination. This button will toggle between
slow and fast speed.
u (Fast Forward Skip): Select this screen button
to go to the next waypoint or to the final destination.
Detour
Detour: Select this screen button from the Route
screen, then select to detour 1 mile, 3 miles, or
5 miles (1 km, 3 km, or 5 km) around the current
route. You may also select to detour the whole
route if necessary. This option is only available
while you are driving on your current planned route.
Voice Prompt
Select this screen button from the Route screen
to turn voice prompts on or off and to change
the volume of voice prompts. See “Nav” under
Configure Menu on page 43 for more information.
40
Add Waypoint: Select this screen button from
the Route screen. This feature allows you to
add up to three waypoints to the current route,
between your start point and final destination.
Once a waypoint has been added, the points
can be edited or deleted.
To add a waypoint:
1. Press the DEST hard key.
2. Select the Add Waypoint screen button.
This button will only appear if a route has
been calculated.
3. Using the desired method of entering
a destination, enter the waypoint. See
“Destination” previously for more information.
4. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
5. Select the Start Guidance screen button.
You are now ready to start your route.
6. To add the second and third waypoints,
press the DEST hard key, then select the
Add screen button, where you would like
the next waypoint to fall on the route.
7. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
8. Select the Start Guidance screen button.
You are now ready to start your route.
To delete a waypoint from your current route:
1. Press the DEST hard key.
2. Select the Delete screen button for the
desired waypoint to delete.
3. The system will display a pop-up confirmation
message. Choose Yes to delete the waypoint;
touch No to cancel this operation.
4. Select the route preference (Fastest, Shortest,
or Other). The system will calculate and
highlight the route.
5. Select the Start Guidance screen button.
You are now ready to start your route.
Suspend Guidance
Press this screen button, from the Route screen,
to put the current route on hold.
Resume Guidance
Press this screen button, from the Route screen,
to resume guidance on the current route.
Cancel Guidance
Press this screen button, from the Route screen,
to cancel the current route.
41
Adding Destinations to the
Address Book
Adding or Changing Preset
Destinations
There are two ways to add a destination to the
address book:
• To add the current final destination to the
address book, press the Mark screen
button from the map screen. The system
will automatically save the final destination
information in the address book.
• Press the Add to Address Book screen button
when available on POI information screens,
Destination Entry screens, or POI screens.
The system will automatically save this
information in the address book.
This feature allows you to add or change one
of five preset destinations. When a destination
has been added as a preset destination, it will be
available to select from the Destination Entry
screen. See “Preset Destination” previously for
information on how to select a preset destination
as a final destination.
See “Nav” under Configure Menu on page 43
for information on editing address book entries.
42
To store the current final destination as a preset
destination:
1. Select the Mark screen button from the map
screen to add the current final destination.
The Address Book screen will appear.
2. Select the Name screen button. An
alpha-keyboard will display. Enter the name.
3. Press and hold one of the buttons at
the bottom of the screen until a pop-up
confirmation displays.
The name will appear in that preset destination
screen button and is now available to select
from the Destination Entry screen.
To store an address book entry as a preset
destination:
1. Select the MENU hard key.
2. Select the Nav screen button or press the
MENU key until the Nav screen button is
selected.
3. Select the Edit/View screen button.
4. Select the address book entry that you
would like to store as the preset destination.
Select the Name screen button to add a
name, if needed.
5. Press and hold one of the buttons at the
bottom of the screen until a pop-up
confirmation displays.
The name will appear in the that preset
destination screen button and is now available
to select from the Destination Entry screen.
Configure Menu
Press the MENU hard key to adjust several of
your system’s features and preferences. The last
selected menu screen will be the screen that
displays (Sound, Radio, Nav (navigation), Display,
or Time).
43
Sound
Nav (Navigation)
Press the MENU key to enter the Menu options,
then press the MENU key repeatedly until Sound
is selected or touch the Sound screen button
to make speaker and equalization or DSP (Digital
Signal Processing), if equipped with the Bose®
sound system, adjustments. See Navigation Audio
System on page 60 for more information.
Radio
Press the MENU key to enter the Menu options,
then press the MENU key repeatedly until Radio
is selected or touch the Radio screen button
to make changes for radio information displayed,
preset pages, XM™ categories, and Automatic
Volume Control or Bose® AudioPilot®, if your
vehicle has the Bose® sound system. See
Navigation Audio System on page 60 for more
information.
44
Press the MENU key to enter the Menu options,
then press the MENU key repeatedly until
Nav is selected or touch the Nav screen button.
Voice Prompt
Route Preference
Touch the % Route Preference screen button to
change route options when the system calculates
a route.
Allow highway: This feature allows the system
to use major roads when calculating a planned
route.
Allow toll road: This feature allows the system to
use toll roads when calculating a planned route.
Allow ferry: This feature allows the system to use
ferries when calculating a planned route.
> Voice Prompt: Touch the Voice Prompt
screen button to change the volume of the voice
prompts or to turn the voice prompts on and off.
Voice Prompt Volume: Touch the + (plus)
or − (minus) screen buttons to increase or to
decrease the volume of the voice prompts.
Turn voice turn instruction: Touch the ON or
OFF screen buttons to turn voice instructions
on and off while traveling on a planned route.
Allow time and seasonal restricted road: This
feature allows the system to use time restricted
and seasonal roads when calculating a planned
route.
Edit Address Book — How to Add
To add an address to the address book, see
“Adding Destinations to the Address Book” under
Destination on page 27.
45
Edit Address Book — Edit/View
To edit the name of an address book:
1. Select the MENU hard key.
2. Select the NAV screen button.
3. Select the * Edit/View Address Book screen
button.
4. Select the Address book entry.
To add or change the phone number of an
address book entry:
1. Select the MENU hard key.
2. Select the NAV screen button.
3. Select the * Edit/View Address Book screen
button.
4. Select the address book entry to change.
5. Touch the Phone # screen button and use the
numeric keyboard to enter or change the
phone number.
6. Touch the OK screen button to save your
changes.
To change the map icon of an address book entry:
1. Select the MENU hard key.
2. Select the NAV screen button.
5. Touch the Name screen button and use the
alpha keyboard to edit or add the name.
6. Touch the OK screen button to save your
changes.
46
3. Select the * Edit/View Address Book screen
button.
4. Select the address book entry to change.
5. Select the Icon screen button.
6. Select an icon from the list.
To add a voice tag to an address book entry:
1. Select the MENU hard key.
2. Select the NAV screen button.
3. Select the * Edit/View Address Book screen
button.
4. Select the Add Voice tag screen button.
5. The system will ask for you to state the name.
You will have five seconds to state the name.
The system will respond back with the name.
3. Select the * Edit/View Address Book screen
button.
4. Select the address book entry to delete.
5. Press and hold the Delete screen button until
the delete all address book entries pop-up
confirmation displays. Select Yes to delete;
select No to cancel the operation.
Map Database Information
To delete an address book entry:
1. Select the MENU hard key.
2. Select the NAV screen button.
3. Select the * Edit/View Address Book screen
button.
4. Select the address book entry to delete.
5. Press the Delete screen button to delete the
address book entry.
To delete the entire address book:
1. Select the MENU hard key.
2. Select the NAV screen button.
Touch the Map Database Information screen
button to change the map DVD and to view the
coverage areas of the map DVD.
47
Change: Touch this screen button to eject or
change the map DVD. The screen will tilt, exposing
the map DVD slot and, if loaded, the map DVD
will eject. Pull the map DVD out. Insert the
map DVD partway into the slot. The system
will pull it in.
Once the screen is closed, touch the OK screen
button to proceed to the navigation system.
See Getting Started on page 6 for more
information.
Coverage: Touch this screen button to view the
areas covered by the map DVD.
Once the map DVD is loaded touch the Close
screen button. The screen will close.
48
Touch the up and down arrow screen buttons to
view each region of the map DVD. The screen will
display the major cities for the selected region.
Low Fuel Warning
Off-Road Mode
To turn the Low Fuel Warning on or off, do the
following:
1. Press the MENU key.
To turn the Off-Road Mode on or off, do the
following:
1. Press the MENU key.
2. Press the Nav screen button.
2. Press the Nav screen button.
3. Press the @ Low Fuel Warning ON or
OFF screen button. The active button
will be highlighted.
When on, a warning will appear on the
display when your vehicle’s fuel tank is low
on fuel. The warning pop-up window will ask
if you would like to view gas station POIs
on the map display. Once the gas station POIs
are displayed you can automatically route to
a gas station by touching the gas station
POI symbol on the screen and pressing the
GO screen button.
To remove the POIs from the screen, see the
POI information under Symbols on page 20
for more information.
See “Fuel” in the Index of your vehicle’s
owner manual.
3. Press the # Off-Road Mode ON or
OFF screen buttons. The active button
will be highlighted.
When the off-road mode is turned on, the
navigation system will show the path being
traveled by the vehicle when not on a marked
road. This path will be a simulation since
the map database coverage will not have
these roads on the DVD. This path will
be stored in the navigation system’s memory,
see “Previous Destination” under Destination
on page 27 for more information.
See “Off-Road Driving” in the Index of your
vehicle’s owner manual for more information
about off-road driving.
49
Display
Brightness/Contrast/Mode
Press the MENU key to enter the Menu options,
then press the MENU key repeatedly until Display
is selected or touch the Display screen button.
Touch this screen button to change the brightness,
contrast, and mode of the display.
Display Off
Touch this screen button to turn the display off.
Press any hard key to view the display.
50
] (Brightness): Touch the + (plus) or − (minus)
screen buttons to increase or decrease the
brightness of the screen.
_ (Contrast): Touch the + (plus) or − (minus)
screen buttons to increase or decrease the
contrast of the screen.
Auto (Automatic): Touch this screen button for
the system to automatically adjust the screen
background depending on exterior lighting
conditions.
Rear Vision Camera
Night: Touch this screen button and the system
will make the screen background darken.
Press the MENU key to enter the menu options,
then press the MENU key repeatedly until the time
is selected or touch the time screen button.
The rear vision camera system is designed to
help the driver when backing up by displaying a
view, on the navigation screen, of the area behind
the vehicle when the driver shifts the vehicle
into REVERSE (R). Once the driver shifts out of
REVERSE (R), the navigation screen will go back
to the last screen that had been displayed; after a
delay, if any portion of the screen is touched, or if
the vehicle speed is greater than 7 mph (11 km/h).
Hours: Press the − (minus) or + (plus) signs to
decrease or increase the hours.
Turning the Rear Vision Camera System
On or Off
Minutes: Press the − (minus) or + (plus) signs
to decrease or increase the minutes.
To turn the rear vision camera system on or off,
do the following:
1. Shift into PARK (P).
2. Press the MENU hard key to enter the
Menu options, then press the MENU hard
key to select Display or touch the Display
screen button.
Day: Touch this screen button and the system
will make the screen background brighten.
Setting the Time
12/24 Format: Select the 12 screen button for
standard time; select the 24 screen button
for military time.
Your vehicle may have a rear vision camera
system. Read this entire section before using
the camera system.
51
3. Select the + Rear Camera Options screen
button. The Rear Camera Options screen will
display.
4. Select the Rear Camera Image in Reverse
screen button. The screen button will be
highlighted when on.
The delay that is received after shifting out of
REVERSE (R) is approximately 10 seconds.
The delay can be cancelled by performing
one of the following:
• Pressing a hard key on the navigation system
or touching the navigation screen.
• Shifting in to PARK (P).
• Reach a vehicle speed of 7 mph (11 km/h).
There is a message on the rear vision camera
screen that states “Turn to See Off Screen
Objects”.
52
{CAUTION:
Do not back the vehicle while only
looking at the rear vision camera screen.
The distances between objects and
surfaces will differ from actual distances.
The camera system does not display
objects that are below the bumper,
underneath the vehicle, or objects out of
the camera’s field of view. The rear vision
camera is not intended for use during
longer backing maneuvers or backing
into potential crossing traffic. Crossing
traffic may be approaching outside
of the camera’s field of view.
CAUTION:
(Continued)
Area Displayed On Screen
CAUTION:
(Continued)
If the driver backs up the vehicle while
only looking at the screen, they may
hit a pedestrian, bicyclist, child, pet, or
other object resulting in injury or death.
The driver should always check behind
and around the vehicle when backing up
just as they would if they did not have
the rear vision camera.
Yukon XL Denali shown; Yukon, Yukon XL,
Yukon Denali, Tahoe, Suburban, Avalanche similar
The image is provided by the camera located above
the license plate or just under the endgate handle.
53
The camera uses a special lens. The distance of
the image that appears on the screen differs
from the actual distance. The area displayed by
the camera is limited. The camera does not display
objects which are close to either corner of the
bumper or under the bumper. The area displayed
on the screen may vary according to vehicle
orientation or road conditions.
The following illustration shows the field of view
that the camera provides.
Yukon XL Denali shown; Yukon, Yukon XL,
Yukon Denali, Tahoe, Suburban, Avalanche similar
54
Adjusting the Brightness and Contrast
of the Screen
• When the sun or the beam of headlights is
To adjust the brightness and contrast of the
screen, press the MENU key while the rear vision
camera image is on the display. Any adjustments
made will only effect the rear vision camera
screen.
•
•
] (Brightness): Touch the + (plus) or – (minus)
screen buttons to increase or decrease the
brightness of the screen.
_ (Contrast): Touch the + (plus) or – (minus)
screen buttons to increase or decrease the
contrast of the screen.
When the System Does Not Seem To
Work Properly
The rear vision camera system may not work
properly or display a clear image in the following
situations:
• The feature may be turned off. See
“Turning the Rear Vision Camera System
On or Off” previously to turn the system on.
• In the dark.
•
•
shining directly into the camera lens.
If ice, snow, mud, or anything else builds up
on the camera lens. Clean the lens, rinse it
with water, and wipe it with a soft cloth.
If the back of the vehicle is in an accident, the
position and mounting angle of the camera
may change or the camera may be affected.
Be sure to have the camera and its position
and mounting angle checked at your dealer.
Extreme high or low temperatures or extreme
temperature changes can affect the image
displayed.
If the back of the vehicle is in an accident, the
camera may be affected. Have the rear vision
camera system checked at your dealer.
Rear Vision Camera Error Messages
Rear Vision Camera System Unavailable:
This message may display when the system
is not receiving information it requires from
other vehicle systems.
If any other problem occurs or if a problem
persists, see your dealer.
55
Global Positioning System (GPS)
The Navigation System determines the position
of your vehicle by using satellite signals, various
vehicle signals, and map data.
At times, other interferences such as the satellite
condition, road configuration, the condition of
the vehicle and/or other circumstances can
interfere with the Navigation’s ability to determine
the accurate position of the vehicle.
The GPS shows the current position of your
vehicle using signals sent by the GPS Satellites
of the United States Department of Defense.
When your vehicle is not receiving signals from
the satellites, a symbol will appear on the
map screen. Refer to Symbols on page 20.
This system may not be available or interference
may occur if the following happens:
• Signal obstructions caused by tall buildings,
large trucks, tunnels,
• objects located on top of the instrument panel,
• satellites will not send signals if they are
being repaired or improved,
• after-market glass tinting has been applied
to the vehicle’s windows.
56
Notice: Do not apply after-market glass tinting
to the vehicle’s windows. Glass tinting will
interfere with the system’s ability to receive
GPS signals and cause the system to
malfunction. You might have to replace the
window to correct the problem. This would
not be covered by your warranty.
For more information if you are experiencing a
problem, see If the System Needs Service
on page 58 and Problems with Route Guidance
on page 57.
Vehicle Positioning
At times, the position of the vehicle on the map
may be inaccurate due to one or more of the
following reasons:
• The road system has changed.
• The vehicle is driving on slippery road
surfaces such as in sand, gravel, and/or snow.
• The vehicle is traveling on winding roads.
• The vehicle is on a long straight road.
• The vehicle is approaching a tall building or
a large vehicle.
• The surface streets run parallel to a freeway.
• The vehicle has just been transferred by
a vehicle carrier or a ferry.
• The current position calibration is set
incorrectly.
• The vehicle is traveling at high speed.
• The vehicle changes directions more than
once, or when the vehicle is turning on a
turn table in a parking lot.
• The vehicle is entering and/or exiting a
parking lot, garage, or a lot with a roof.
• The GPS signal is not received.
• A roof carrier is installed on your vehicle.
• The vehicle is being driven with tire chains.
• The tires are replaced.
• The tire pressure for your tires is incorrect.
• The tires are worn.
• The first time the map DVD is inserted.
• The battery is disconnected for several days.
• The vehicle is driving in heavy traffic where
driving is at low speeds, and the vehicle is
stopped and started repeatedly.
If you experience problems with your system,
see your dealer.
Problems with Route Guidance
Inappropriate route guidance may occur under one
or more of the following conditions:
• You have not turned onto the road indicated.
• Route guidance may not be available
when using automatic rerouting for the next
right or left turn.
• The route may not be changed when using
automatic rerouting.
• There is no route guidance when turning at
an intersection.
• Plural names of places may be announced
occasionally.
• It may take a long time to operate automatic
rerouting during high-speed driving.
• Automatic rerouting may display a route
returning to the set waypoint if you are heading
for a destination without passing through a
set waypoint.
• The route prohibits the entry of a vehicle due
to a regulation by time or season or any
other regulation which may be given.
57
• Some routes may not be searched.
• The route to the destination may not be
shown if there are new roads, if roads
have recently changed, or if certain
roads are not listed on the map DVD.
See Ordering Map DVDs on page 58.
To recalibrate the vehicle’s position on the map,
see your dealer.
If the System Needs Service
If your system needs service and you have
followed the steps listed here and still are
experiencing problems, see your dealer for
assistance.
58
Ordering Map DVDs
The map DVD in your vehicle is the most
up-to-date information available when your
vehicle was purchased. The map DVD is updated
periodically, provided that the map information
has changed. To order a new map DVD,
contact your dealer.
Database Coverage Explanations
Coverage areas vary with respect to the level of
map detail available for any given area. Some
areas will feature greater levels of detail than
others. If this happens, it does not mean there
is a problem with the system. As the map DVD
is updated, more detail may become available
for areas which previously had limited detail.
See Ordering Map DVDs on page 58.
Section 3
Navigation Audio System
Navigation Audio System ..............................60
CD Player ....................................................70
DVD Player ..................................................77
Auxiliary Devices ..........................................84
59
Navigation Audio System
Playing the Radio
Notice: Before adding any sound equipment
to your vehicle, such as an audio system,
CD player, CB radio, mobile telephone, or
two-way radio, make sure that it can be added
by checking with your dealer. Also, check
federal rules covering mobile radio and
telephone units. If sound equipment can be
added, it is very important to do it properly.
Added sound equipment may interfere with
the operation of your vehicle’s engine, radio,
or other systems, and even damage them.
Your vehicle’s systems may interfere with
the operation of sound equipment that has
been added.
O(Power/Volume): Press this knob to turn the
Notice: The chime signals related to seat belts,
parking brake, and other functions of your
vehicle operate through the navigation system.
If that equipment is replaced or additional
equipment is added to your vehicle, the chimes
may not work. Make sure that replacement or
additional equipment is compatible with your
vehicle before installing it. See “Accessories
and Modifications” in the Index of your
vehicle’s owner manual.
60
audio system on and off. Turn the knob to increase
or to decrease the volume.
f (Tuning/Sound Knob): Turn this knob to go
to the next or previous frequency and stay there.
Press this knob to display the Sound menu.
See “Sound Menu” later in this section.
AUDIO: Press this key to display the audio screen.
Press the key to switch between AM, FM, or XM,
if equipped, DISC, or AUX (Auxiliary), or touch
the screen button. See CD Player on page 70,
DVD Player on page 77, and Auxiliary Devices
on page 84 for more information.
Finding a Station
FM source shown, other sources similar
FM source shown, other sources similar
If viewing a map screen, touch the source screen
(AM, FM, XM, CD, etc..) button. The display
will split between the audio screen and the map
screen. All station-changing functions can be
performed from this screen.
If you do not want to view a split screen or you
are not on a map screen, press the AUDIO
hard key.
AM/FM/XM: Touch the source (AM, FM, or XM,
if equipped) screen button or press the AUDIO key
repeatedly until the desired source is highlighted.
61
See “Radio Menu” later in this section to add and
remove XM categories from the category list.
When listening to XM stations, you will be able
to select all of the categories when using the right
and left arrow screen buttons on the main audio
screen. The categories, when removed, will not be
enabled to select from the category list screen.
FM lists may also contain a category to select
if stations in your area support Radio Data
Systems (RDS).
FM source shown, other sources similar
Category: Touch the screen button, located in
the middle of the screen, to receive a list of all of
the selected band stations in the area. Use the
up and down arrow screen buttons to scroll
the frequencies. Touch the desired frequency.
XM lists will also contain a category to select
and the stations or channels that pertain to
the category. For XM, touch the left and right
arrow screen buttons to change categories.
The station information will appear on the display.
62
$ Refresh List: Touch this screen button to
refresh the list of stations.
When viewing a map screen, the name of the
station or channel will appear on the display.
¨SEEK / ©SEEK: To seek stations, press
the left or right arrow keys to go to the next or
previous station and stay there.
To scan stations, press and hold either arrow for
more than two seconds. The radio will go to a
station, play for a few seconds, then go on to the
next station. To stop scanning, press either
arrow again.
Storing Preset Stations
Sound Menu
This feature allows you to store up to 30 preset
stations. You can mix AM, FM, and XM
(if equipped). To store presets, do the following:
1. Press the O(power) knob to turn the
system on.
2. If viewing a map screen, touch the source
screen button, press the AUDIO key,
or press the FAV (favorite) key.
3. Select the band.
4. Seek, scan, or tune to the desired station,
to select the station.
5. Press and hold one of the preset screen
buttons for more than two seconds or
until you hear a beep.
6. Repeat the steps for each preset.
Equalization shown, Digital Signal
Processing (DSP) similar
f (Sound Menu): Press this knob or press the
MENU key to access the Sound menu to adjust
the treble, midrange, bass, fade, balance, and
equalization or Digital Signal Processing (DSP),
if equipped with the Bose® sound system.
63
Setting the Tone
Automatic Equalization
TREBLE: Touch the plus (+) or minus (−) sign
to increase or decrease the treble. If a station is
weak or noisy, decrease the treble.
If the system has automatic equalization, you can
select customized equalization settings designed
for Talk. Touch the Talk screen button to hear
the change in sound. The system will save
the setting for each source.
MID (Midrange): Touch the plus (+) or minus (−)
sign to increase or decrease the midrange.
BASS: Touch the plus (+) or minus (−) sign to
increase or decrease the bass.
Adjusting the Speakers
L/R (Left/Right) (Balance): To adjust the balance
between the left and the right speakers, touch
and hold the L or R screen buttons. To center
the balance and the fade, touch the center,
where the two lines meet.
Front/Rear (Fade): To adjust the fade between
the front and the rear speakers, touch and hold
the Front or Rear screen buttons. To center
the balance and the fade, touch the center,
where the two lines meet.
64
To not use the automatic equalization setting,
press any of the screen buttons that will change
the treble, midrange, bass, balance, or fade.
This will take the system out of the equalization
setting so that you can create your own sound.
Digital Signal Processing (DSP)
If the system has the Bose® sound system, the
system will have Digital Signal Processing (DSP).
DSP is used to provide a choice of four different
listening experiences. DSP can be used while
listening to the audio system. The type of DSP
selected is displayed on the status line.
Select from the following DSP settings:
Normal: Select this screen button to adjust the
audio to be in normal mode. DSP will be off.
Surround (Centerpoint™): Select this
screen button to turn on Bose® Centerpoint™.
Centerpoint™ signal processing gives
surround sound listening for a CD, MP3, or
a DVD stereo audio source. Centerpoint™
delivers five independent audio channels
from conventional stereo recordings.
Radio Menu
Rear: Select this screen button to adjust the
audio to give the rear seat occupants the
best possible sound quality.
Driver: Select this screen button to adjust
the audio to give the driver the best possible
sound quality.
Press the MENU key to enter the menu screen,
then press the MENU key repeatedly until Radio
is selected or touch the Radio screen button
to make changes for radio information displayed,
number of preset pages, XM categories, and
Automatic Volume Control or Bose® AudioPilot®.
65
Additional Information Displayed
Touch the 4 Additional Information Displayed
screen button to turn station, channel, CD, and
MP3 information on or off.
Touch the YES screen button to receive
information, when it is available, for the following;
FM: RDS category name and radio text, XM:
Song Title and Artist Name, CD: CD text,
MP3: tag information.
Touch the NO screen button to receive no
information.
Number of Preset Pages
Touch the / Number of Preset Pages screen
button to change the number of preset pages,
1 through 6. Each preset page can contain
five preset stations. Touch the desired
numbered screen button.
Remove/Add XM Categories
Touch the & Remove/Add XM Categories screen
button to remove or add XM categories when
selecting XM categories from the category
list screen. The list of XM categories will appear
on the screen. Use the up and down arrow
screen buttons to scroll through the list.
66
The categories to remove will be highlighted
and the categories to add will be dark in color.
Touch the category that you would like to add
or remove. Touch the Restore All Categories
screen button to add all categories that have
been removed.
Automatic Volume Control or Bose
AudioPilot®
> Automatic Volume Control: With speed
compensated volume, your audio system adjusts
automatically to make up for road and wind
noise as you drive.
Set the volume at the desired level. Touch the
LOW, MEDIUM, or HIGH screen buttons.
Each higher setting allows for more compensation
at faster vehicle speeds. Then, as you drive,
speed compensated volume automatically
increases the volume, as necessary, to overcome
noise at any speed. The volume level should
always sound the same to you as you drive.
To turn speed compensated volume off, touch
the OFF screen button.
AudioPilot®: If the system has the Bose® sound
system, it includes Bose AudioPilot® noise
compensation technology.
To use AudioPilot®, press the > Automatic
Volume Control screen button to access the
AudioPilot® menu, then press the ON screen
button. To turn it off, touch the OFF screen button.
When on, AudioPilot® continuously adjusts the
audio system equalization, to compensate
for background noise, so that your music always
sounds the same at the set volume level.
This feature is most effective at lower volume
settings where background noise can affect
how well you hear the music being played
through your vehicle’s audio system. At higher
volume settings, where the music is much
louder than the background noise, there may
be little or no adjustments by AudioPilot®.
For additional information on AudioPilot®,
please visit www.bose.com.
Radio Data System (RDS)
The audio system has a Radio Data System (RDS).
RDS features are available for use only on FM
stations that broadcast RDS information. With RDS,
the radio can do the following:
• Seek to stations broadcasting the selected type
of programming
• Receive announcements concerning local and
national emergencies
• Display messages from radio stations
This system relies on receiving specific information
from these stations and will only work when the
information is available. In rare cases, a radio
station may broadcast incorrect information that
will cause the radio features to work improperly.
If this happens, contact the radio station.
The RDS system is always on. When information
is broadcast from the FM station you are
listening to, the station name or call letters will
be displayed on the audio screen. RDS may
provide a program type (PTY) for current
programming and the name of the program
being broadcasted.
67
XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in
the 48 contiguous United States and Canada,
if available. XM™ offers over 100 coast-to-coast
channels including music, news, sports, talk,
and children’s programming. XM™ provides
digital quality audio and text information,
including song title and artist name.
Radio Display Message
Condition
A service fee is required in order to receive
the XM™ service. For more information,
contact XM™ at www.xmradio.com or
call 1-800-852-XMXM (9696).
When XM™ is active, the channel name and
number, song title, and artist will be displayed
on the screen.
Action Required
XM Updating
Updating encryption code
The encryption code in the receiver is being updated and
no action is required. This process should take no longer
than 30 seconds.
No XM signal
Loss of signal
The system is functioning correctly, but the vehicle is in a
location that is blocking the XM™ signal. When you move
into an open area, the signal should return.
Loading XM
Acquiring channel audio
(after four second delay)
The audio system is acquiring and processing audio and
text data. No action is needed. This message should
disappear shortly.
Channel Off Air
Channel not in service
This channel is not currently in service. Tune in to another
channel.
Channel Unavail
Channel no longer
available
This previously assigned channel is no longer assigned.
Tune to another station. If this station was one of the
presets, choose another station for that preset button.
68
Radio Display Message
Condition
Action Required
No Artist Info
Artist Name/Feature
not available
No artist information is available at this time on this channel.
The system is working properly.
No Title Info
Song/Program Title
not available
No song title information is available at this time on this
channel. The system is working properly.
No CAT Info
Category Name
not available
No category information is available at this time on this
channel. The system is working properly.
Not Found
No channel available for
the chosen category
There are no channels available for the selected category.
The system is working properly.
No Information
No Text/Informational
message available
No text or informational messages are available at this time
on this channel. The system is working properly.
XM Theftlocked
Theft lock active
The XM™ receiver in the vehicle may have previously been
in another vehicle. For security purposes, XM™ receivers
cannot be swapped between vehicles. If this message is
received after having your vehicle serviced, check with your
GM dealer.
XM Radio ID
Radio ID label (channel 0)
If tuned to channel 0, this message will alternate with the
XM™ Radio eight digit radio ID label. This label is needed
to activate the service.
Unknown
Radio ID not known
(should only be if
hardware failure)
If this message is received when tuned to channel 0, there
may be a receiver fault. Consult with your GM dealer.
Check XM Receiver
Hardware failure
If this message does not clear within a short period of time,
the receiver may have a fault. Consult with your GM dealer.
69
CD Player
The player can be used for CD and MP3. If your
vehicle has RSE, the player can be used for
CD, MP3, DVD audio, and as a DVD video player.
See DVD Player on page 77 for more information
about DVD audio and video.
With the ignition on, insert a CD partway into the
slot, label side up. The player will pull it in and
the CD should begin playing. While playing a CD,
the navigation system is available. If you insert
a CD with the system off and the ignition on,
it will start to play.
When you insert a CD, the CD tab will display.
If you turn off the ignition or radio with a CD in the
player, it will stay in the player. When you turn on
the ignition or radio, the CD will start playing where
it stopped, if it was the last selected audio source.
As each new track starts to play, the track number
will appear on the display.
The CD player can play the smaller 3 inch (8cm)
single CDs with an adapter ring. Full-size CDs and
the smaller CDs are loaded in the same manner.
70
If playing a CD-R the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been handled.
There may be an increase in skipping, difficulty
in finding tracks, and/or difficulty in loading and
ejecting. If these problems occur, check the bottom
surface of the CD. If the surface of the CD is
damaged, such as cracked, broken, or scratched,
the CD will not play properly. If the surface of
the CD is soiled, see “Care of Your CDs” in the
Index of your vehicle’s owner manual.
If there is no apparent damage, try a known
good CD.
Notice: If you add any label to a CD, insert
more than one CD into the slot at a time,
or attempt to play scratched or damaged
CDs, you could damage the CD player.
When using the CD player, use only CDs in
good condition without any label, load one
CD at a time, and keep the CD player and
the loading slot free of foreign materials,
liquids, and debris.
Do not add any label to a CD, it could get
caught in the CD player. If a CD is recorded on
a personal computer and a description label
is needed, try labeling the top of the recorded
CD with a soft marker instead.
Playing an Audio CD
If an error appears on the display, see
“CD Messages” later in this section.
If viewing a map screen, touch the CD screen
button. The display will split between the
audio screen and the map screen. If you do
not want to view a split screen or you are not
on a map screen, press the AUDIO key then
press the AUDIO key until CD is highlighted
or touch the CD screen button.
j/ r (Pause/Play): Touch this button to pause
the CD. This button will then change to the
play button. Touch the play button to play the CD.
RANDOM: Touch this button to hear the tracks
in random, rather than sequential, order.
Touch RANDOM again to turn off random play.
r (Rewind): Touch and hold this button to
rewind quickly through a track selection. You
will hear sound at a reduced volume. Release
this button to stop rewinding. The display will
show the elapsed time of the track.
71
[ (Forward): Touch and hold this button to
fast forward quickly through a track selection.
You will hear sound at a reduced volume. Release
this button to stop fast forwarding. The display
will show the elapsed time of the track.
¨SEEK / ©SEEK: Press the right arrow to go
to the next track. Press the left arrow to go to
the start of the current track, if more than
five seconds have played. If either arrow is
pressed more than once, the player will continue
moving backward or forward through the CD.
The sound will mute while seeking.
When playing an audio CD, if your vehicle has
RSE, the rear seat operator can power on the
RSE video screen and use the remote control
to navigate through the tracks on the CD.
Using an MP3 CD
MP3 Format
There are guidelines that must be met, when
creating an MP3 disc. If the guidelines are not met
when recording a CD-R(W), the CD may not play.
72
The guidelines are:
• Sampling rate: 16 kHz, 22.05 kHz, 24 kHz,
32 kHz, and 44.1 kHz.
• Bit rates supported: 32, 40, 48, 56, 64, 80, 96,
112, 128, 160, 192, 224, 256, and 320 kbps.
• ID3 tag information is displayed by the radio
if it is available. The radio supports ID3 tag
information v1.0 or v1.1. The radio will display
a filename, song name, artist name, album
name, and directory name.
• Maximum 32 characters, including spaces,
in a file or folder name.
• Maximum number of folders is 253 with a
maximum hierarchy of eight folders.
• Create a folder structure that makes it easy to
find songs while driving. Organize songs by
albums using one folder for each album.
Each folder or album should contain 18 songs
or less.
• It is recommended that there is a maximum
of 192 files on a disc.
• The files can be recorded on a CD-R or CD-RW
with a maximum capacity of 700MB.
• DVD with MP3 are not playable on this system.
Root Directory
The root directory will be treated as a folder.
If the root directory has compressed audio
files, the directory will be displayed as ROOT.
All files contained directly under the root directory
will be accessed prior to any root directory
folders. However, playlists (Px) will always be
accessed before root folders or files.
Empty Directory or Folder
If a root directory or a folder exists somewhere
in the file structure that contains only folders/
subfolders and no compressed files directly
beneath them, the player will advance to the
next folder in the file structure that contains
compressed audio files and the empty folder
will not be displayed or numbered.
No Folder
When the CD contains only compressed files,
the files will be located under the root folder.
The next and previous folder functions will have
no function on a CD that was recorded without
folders or playlists. When displaying the name
of the folder the radio will display ROOT.
When the CD contains only playlists and
compressed audio files, but no folders, all files
will be located under the root folder. The left
and right arrow buttons will search playlists (Px)
first and then go to the root folder. When the
radio displays the name of the folder the radio
will display ROOT.
Order of Play
Tracks will be played in the following order:
• Play will begin from the first track in the first
playlist and will continue sequentially through
all tracks in each playlist. When the last track
of the last playlist has been played, play will
continue from the first track of the first playlist.
• If the CD does not contain any playlists, then
play will begin from the first track under the
root directory. When all tracks from the root
directory have been played, play will continue
from files according to their numerical listing.
After playing the last track from the last folder,
play will begin again at the first track of the
first folder or root directory.
When play enters a new folder, the display will
not automatically show the new folder name.
The new track name will appear on the display.
73
File System and Naming
When you insert a CD, the CD tab will display.
The song name that will display will be the song
name that is contained in the ID3 tag. If the
song name is not present in the ID3 tag, then
the radio will display the file name without
the extension (such as .mp3) as the track name.
If you turn off the ignition or radio with a CD in the
player, it will stay in the player. When you turn
on the ignition or radio, the CD will start playing
where it stopped, if it was the last selected
audio source.
Track names longer than 32 characters or
four pages will be shortened. The display will
not show parts of words on the last page of text
and the extension of the filename will not display.
As each new track starts to play, the track number
will appear on the display.
Preprogrammed Playlists
You can access preprogrammed playlists which
were created by WinAmp™, MusicMatch™,
or Real Jukebox™ software, however, you will
not have editing capability. These playlists will be
treated as special folders containing compressed
audio song files.
Playing an MP3
With the ignition on, insert a CD partway into the
slot, label side up. The player will pull it in and
the CD should begin playing. While playing a CD,
the navigation system is available. If you insert
a CD with the system off and the ignition on,
it will start to play.
74
If playing a CD-R the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There may be an increase in skipping,
difficulty in finding tracks, and/or difficulty in
loading and ejecting. If these problems occur,
check the bottom surface of the CD. If the surface
of the CD is damaged, such as cracked, broken,
or scratched, the CD will not play properly.
If the surface of the CD is soiled, see “Care of
Your CDs” in the Index of your vehicle’s
owner manual.
If there is no apparent damage, try a known
good CD.
Notice: If you add any label to a CD, insert
more than one CD into the slot at a time,
or attempt to play scratched or damaged
CDs, you could damage the CD player.
When using the CD player, use only CDs
in good condition without any label, load
one CD at a time, and keep the CD player
and the loading slot free of foreign materials,
liquids, and debris.
Do not add any label to a CD, it could get
caught in the CD player. If a CD is recorded on
a personal computer and a description label
is needed, try labeling the top of the recorded
CD with a soft marker instead.
If an error appears on the display, see
“CD Messages” later in this section.
If viewing a map screen, touch the CD screen
button. The display will split between the audio
screen and the map screen. If you do not want
to view a split screen or you are not on a
map screen, press the AUDIO key to enter the
audio screen, then press the AUDIO key until
CD is highlighted or touch the CD screen button.
j/ r (Pause/Play): Touch this button to pause
the CD. This button will then change to the
play button. Touch the play button to play the CD.
Random: Touch this screen button to hear the
disc played in random (tracks and folders)
order. Touch the Random screen button to turn
off random play.
r(Rewind): Touch and hold this button to
rewind quickly through a track selection. You will
hear sound at a reduced volume. Release this
button to stop rewinding. The display will show
the elapsed time of the track.
75
[ (Forward): Touch and hold this button to
fast forward quickly through a track selection.
You will hear sound at a reduced volume. Release
this button to stop fast forwarding. The display
will show the elapsed time of the track.
qr (Folder): Select the left or right arrow to
go to the previous or next folder on the disc.
Press the middle screen button, with the folder
name, to sort the MP3 by folder and file name.
It may take a few minutes for the system to
sort the MP3.
Sort By: Touch this screen button to organize
the MP3 to enable you to sort the MP3 by artist,
album, and genre. It may take a few minutes
for the system to sort the MP3.
¨SEEK / ©SEEK: Press the right arrow to
go to the next track. Press the left arrow to go
to the start of the current track, if more than
five seconds have played. If either arrow is
pressed more than once, the player will continue
moving backward or forward through the CD.
The sound will mute while seeking.
76
When playing an MP3, if your vehicle has RSE,
the rear seat operator can power on the RSE video
screen and use the remote control to navigate
through the MP3.
CD Messages
If Disc Read Error appears on the display and/or
the CD comes out, it could be for one of the
following reasons:
• If a disc was inserted with an invalid or
unknown format.
• If the map DVD disc was installed into the
CD slot. See “Installing the Map DVD”
under Maps on page 18 for more information.
• It is very hot. When the temperature returns
to normal, the CD should play.
• You are driving on a very rough road. When the
road becomes smoother, the CD should play.
• The CD is dirty, scratched, wet, or
upside down.
• The air is very humid. If so, wait about an hour
and try again.
• There may have been a problem while burning
the CD.
• The label may be caught in the CD player.
If the CD is not playing correctly, for any other
reason, try a known good CD.
If any error occurs repeatedly or if an error cannot
be corrected, contact your dealer.
DVD Player
The player can be used for CD, MP3, DVD audio,
and as a DVD video player.
With the ignition on, insert a DVD partway into
the slot, label side up. The player will pull it
in and the DVD should begin playing. While
playing a DVD, the navigation system is available.
If you insert a DVD with the system off and the
ignition on, it will start to play.
This feature will not operate on the navigation
screen unless the vehicle is in PARK (P).
The Rear Seat Entertainment (RSE) video screen
will start play of the DVD when a DVD has
been inserted into the navigation system. See
“Rear Seat Entertainment System” in the Index of
your vehicle’s owner manual for more information.
The DVD player is only compatible with DVDs
of the appropriate region code that is printed on
the jacket of most DVDs.
The DVD slot is compatible with most audio
CDs, CD-R, CD-RW, DVD-Video, DVD-Audio,
DVD-R/RW, DVD+R/RW media along with
MP3 and WMA formats.
If playing any compatible DVD-R the sound
quality may be reduced due to disc quality,
the method of recording, the quality of the video
that has been recorded, and the way the disc
has been handled. There may be an increase in
skipping, difficulty in finding chapters, and/or
difficulty in loading and ejecting. If these problems
occur, check the bottom surface of the DVD.
If the surface of the DVD is damaged, such as
cracked, broken, or scratched, the DVD will
not play properly.
77
If there is no apparent damage, try a known
good DVD.
Notice: If you add any label to a DVD, insert
more than one DVD into the slot at a time,
or attempt to play scratched or damaged
DVDs, you could damage the DVD player.
When using the DVD player, use only DVDs
in good condition without any label, load
one DVD at a time, and keep the DVD player
and the loading slot free of foreign materials,
liquids, and debris.
Do not add any label to a DVD, it could get
caught in the DVD player. If a DVD is recorded
on a personal computer and a description label
is needed, try labeling the top of the recorded
DVD with a soft marker instead.
If an error appears on the display, see
“DVD Messages” later in this section.
78
Playing a DVD
There are three ways to play a DVD:
• Once a DVD is inserted, the system will
automatically start play of the DVD.
• If you are on a map screen, touch the
DVD screen button.
• Press the AUDIO hard key, then touch
the DVD screen button.
When a DVD is loaded in the DVD player,
the rear seat operator can power on the RSE
video screen and use the remote control to
navigate through the DVD.
O (Power/Volume): Press this knob to turn the
system on and off. Turn the knob to increase
or decrease the volume of the audio system.
Press and hold this knob for more than two seconds
to turn the navigation system, RSE, and RSA off.
DVD Menu Options
Once a DVD starts to play, the menu options will
automatically appear. To display the menu
choices while a DVD is playing in full screen,
touch anywhere on the screen.
Full: Press this screen button to remove all
menu options from the display. Press anywhere
on the screen to display the menu options.
Cursor: Touch this button to access the cursor
menu. The arrows and other cursor options
allow you to navigate the DVD menu options.
The cursor menu options are only available if a
DVD has a menu.
q, Q, r, R (Arrow Buttons): Use these arrow
buttons to move around the DVD menu.
Enter: Touch this button to select the highlighted
option.
Return: Touch this button to go back to the
previous DVD menu.
There are three pages of menu options. Press
the right and left arrow screen buttons to use
all of the menu screen buttons. Menu options
are available when they are highlighted.
Some menu options are only available when
the DVD is not playing.
Back: Touch this button to go back to the main
DVD display screen.
Move: Touch this button to move the cursor
buttons back and forth from the bottom-right
corner to the top-left corner of the screen.
79
j/ r (Pause/Play): Touch this button to pause
the DVD. This button will then change to the play
button. Touch the play button to play the DVD.
Menu: Touch this button to display the DVD menu
of the current area of the DVD that is playing.
This button is not available for DVD audio.
Random: Touch this button to hear the tracks
in random, rather than sequential, order. Touch
Random again to turn off random play. This button
is not available for DVD video.
Search: Touch this button to display the title
search screen. The keyboard allows you to type
in the title number of the title that you would like
to watch.
c(Stop): Touch this button to stop play of the
Setup: Touch this button to display the DVD
Setup screen. This button is only available when
the DVD is not playing. The DVD Setup screen
allows you to change the brightness, contrast, and
mode, change the viewing on the monitor, and
to change the initial settings; language, parental
level, and aspect.
DVD. Press the play button to continue playing the
DVD from where the DVD was stopped. Press this
button twice to return to the beginning of the DVD.
r(Rewind): Touch and hold this button to
rewind through the scene, chapters, and titles.
This button may not work when the DVD is playing
the copyright information or the previews.
[(Forward): Touch and hold this button to
advance rapidly through the scene, chapters, and
titles. This button may not work when the DVD is
playing the copyright information or the previews.
Top Menu: Touch this button to display the first
menu of the DVD. This button is not available
on all DVDs.
80
!(Brightness): Touch the up or down screen
arrows to increase or decrease the brightness
of the navigation screen.
_ (Contrast): Touch the up or down screen
arrows to increase or decrease the contrast of
the navigation screen.
Auto (Automatic): Touch this screen button for
the system to automatically adjust the navigation
screen background depending on exterior
lighting conditions.
Night: Touch this screen button and the system
will make the navigation screen background
brighten.
Initial Settings: From the DVD Setup screen,
touch this button to change audio, subtitle,
and menu languages, parental level, and to
view the aspect of the DVD. The movie must
be stopped to use this menu. These settings
are not available on all DVDs.
Day: Touch this screen button and the system will
make the navigation screen background darken.
Monitor: From the DVD Setup screen, touch
this button to adjust the viewing angle of the DVD
on the navigation screen. This is not available
on all DVDs.
Touch the e button to close the screen in from
the left and right sides.
Touch the J button to fill the screen on the
left and right sides.
Touch the d button to fill the screen on the
top and bottom.
Audio Language: Touch English, Francais, or
Espanol to change the language that you are
listening to.
Subtitle Language: Touch English, Francais, or
Espanol to change the language of the subtitles.
81
Menu Language: Touch English, Francais, or
Espanol to change the language of the menus.
Parental Level: Touch this button to change the
rating level to only allow the play of DVDs with
a certain rating. The rating selection is 1 through 8,
with 1 being a G rating. If the 1 is selected, any
DVD with a rating above G will not be able to
be viewed without entering a password.
When the parental level screen is first entered
a keyboard will appear on the display and a
four-digit password will need to be created. Type
in a password that you will be able to remember.
Once the password is created, you can then
select a rating level.
If you would like to change the rating level,
press the Parental Level button, then press the
Password button. Type in the password and
then change the rating level.
This may not be available on all DVDs.
Aspect: Touch this button to change the aspect
ratio of the DVD. This may not be available
on all DVDs.
82
Audio: Press this button to display the audio
stream number and to change the language heard.
Repeatedly press this button to toggle through
the available languages. This may not be available
on all DVDs. This button is not available when
the DVD is stopped.
Subtitle: Touch this button to playback the video
with subtitles. Repeatedly press this button to
toggle through the available languages. To turn the
subtitles off, press this button until Off is selected.
This button is not available when the DVD is
stopped. This may not be available on all DVDs.
Angle: Touch this button to adjust the viewing
angle of the DVD. Repeatedly press this button
to toggle through the angles. This button is
not available when the DVD is stopped. This
may not be available on all DVDs.
q Page: Press this button to go to the previous
scene. This button is not available when the
DVD is stopped. This button is not available for
DVD video.
Page r: Press this button to go to the next
scene. This button is not available when the
DVD is stopped. This button is not available
for DVD video.
• If the map DVD disc was installed into the
SEEK ¨(Next Track/Chapter): Press this
hard key to go to the next track or chapter. This
button may not work when the DVD is playing the
copyright information or the previews.
•
©SEEK (Previous Track/Chapter): Press this
hard key to return to the start of the current
track or chapter. Press this button again to go to
the previous track or chapter. This button may
not work when the DVD is playing the copyright
information or the previews.
•
•
•
•
DVD Messages
If Disc Read Error appears on the display and/or
the DVD comes out, it could be for one of the
following reasons:
• If a disc was inserted with an invalid or
unknown format.
• If the disc is not from a correct region.
•
DVD audio/video slot. See “Installing the
Map DVD” under Maps on page 18 for more
information.
It is very hot. When the temperature returns
to normal, the DVD should play.
You are driving on a very rough road. When
the road becomes smoother, the DVD
should play.
The DVD is dirty, scratched, wet, or
upside down.
The air is very humid. If so, wait about an
hour and try again.
There may have been a problem while
burning the DVD.
The label may be caught in the DVD player.
If the DVD is not playing correctly, for any
other reason, try a known good DVD.
If any error occurs repeatedly or if an error
cannot be corrected, contact your dealer.
83
Auxiliary Devices
The navigation system has an auxiliary input jack
located in the upper right corner of the faceplate.
This is not an audio output; do not plug the
headphone set into the front auxiliary input jack.
You can however, connect an external audio
device such as an iPod, laptop computer,
MP3 player, CD changer, or cassette tape player,
etc. to the auxiliary input jack for use as another
source for audio listening.
If your vehicle has rear audio/video input jacks,
located in the rear of the center console, they
can be used as another source for audio/video
listening.
84
To use a portable audio player, connect a
3.5 mm (1/8 inch) cable to the auxiliary input
jack. When a device is connected, the system
will detect and automatically begin playing audio
from the device over the vehicle’s speakers.
If a device is connected and you are listening to
another source (FM, CD, MP3, etc.), press the
AUDIO key then press the AUDIO key repeatedly
until AUX is selected or touch the AUX screen
button. An auxiliary device must be connected for
the AUX screen button to appear as an option to
select or the vehicle must have rear auxiliary jacks.
See “Rear Seat Entertainment System” in the
Index of your vehicle’s owner manual for more
information on the rear auxiliary jacks.
Section 4
Voice Recognition
Voice Recognition .........................................86
85
Voice Recognition
The navigation system’s voice recognition
allows for hands-free operation of the navigation
system, audio system, and OnStar® features.
Voice recognition can be used when the ignition
is on or when Retained Accessory Power (RAP) is
active. See “Retained Accessory Power (RAP)”
in the Index of your vehicle’s owner manual
for more information.
To use voice recognition, do the following:
1. Press the talk
symbol steering
wheel control
and release it when
you hear a beep.
The audio system,
if on, will mute.
2. Clearly state one of the commands listed on
the following pages.
86
Helpful Hints for Stating Commands
• When a multiple command is available, choose
the command that best works for you.
• Words that are in brackets are optional.
For example, for the command Radio [band]
[select] FM, stating Radio FM or Radio
select FM are both valid commands.
• When the system recognizes the command
the system will:
• either perform the function
• ask you to confirm your choice by clearly
stating “yes or no”
• issue an error message such as “System
does not recognize this command” or
direct you to “Please start speaking after
the beep”
• If the system is not yet ready, the system
may state “System is checking the disc.
Please wait.”.
• To cancel a command or if the system
response does not match your verbal
command, press and hold the talk symbol
button. The system will reply, “System
will cancel the voice recognition”.
• If you experience difficulty with the system
recognizing a command, try saying it more
softly, and wait for a few seconds after
the beep, or you may just try saying it again.
• Background noise may cause voice
commands to be misunderstood, including
airflow noise from wind.
• To use the voice recognition system, the
map DVD must be loaded.
This system is able to recognize commands in
three different languages. The system will only
recognize commands based on the language
selected from the Driver Information Center (DIC).
See “Driver Information Center, DIC Vehicle
Personalization” in the Index of your vehicles
owner manual.
Voice Recognition Commands
The following list shows all of the voice commands
available for the navigation system with a brief
description of each. The commands are listed
with the optional words in brackets. To use
the voice commands, refer to the instructions
listed previously.
Voice tag Commands
The following are voice tag commands you can
access by clearly stating the commands exactly
as they are written. You may have up to 40 voice
tag entries for destinations.
Navigation go to [destination] (voice tag),
navigation select [destination] (voice tag):
These commands instruct the system to select
a destination saved under the voice tag you
have stored.
If you are not currently driving on a route,
the system will automatically create the voice tag
destination as the final destination. If you are
currently driving on a route, the system will
automatically create the voice tag destination as
a waypoint. Up to three waypoints can be created.
87
Storing Voice Tags
Radio Commands
From the address book entry information
page, press the Add Voice tag screen button.
The system will respond “Name Please?”.
Navigation Help
The following are radio commands you can
access by clearly stating the commands exactly
as they are written. The commands are only
available when you are in one of the following
audio modes, AM, FM, or XM™ (if equipped).
Navigation Help: This command instructs the
system to assist with navigation commands.
Radio: This command instructs the system to turn
the audio system on.
Display Commands
Radio [band] [select] AM, radio [band] [select]
FM, radio [band] [select] XM, radio [band]
[select] satellite: These commands instruct
the system to go to either the AM, FM, or XM
(if equipped).
Use the following display commands to set the
display mode.
Display [set] day [mode]: Use this command
to set the display to daytime mode.
Display [set] night [mode]: Use this command
to set the display to night mode.
Display [set] auto [mode]: Use this command
to set the display to automatic mode. The system
will change between day and night mode
automatically.
System help: This command instructs the system
to assist with display commands.
88
Radio [select] (frequency) AM, radio [select]
(frequency) FM: These commands instruct
the system to go to a specific frequency on
either AM or FM.
Radio [select] (channel) XM, radio [select]
(channel) satellite: These commands instruct
the system to go to a specific channel on the
XM™ band (if equipped).
Radio help: This command instructs the system
to assist with radio commands.
CD Commands
Auxiliary Commands
The following are CD, MP3, and DVD commands
that can be accessed by clearly stating the
commands exactly as they are written.
The following auxiliary commands can be
accessed by clearly stating the commands exactly
as they are written. The commands are available
when the auxiliary source is available.
CD, DVD, Disc: Use this command to select
a CD, DVD, or disc that is currently loaded.
CD, DVD, Disc, [select] track (one, two,
three, etc.): This command instructs the
system to select a specific track number.
CD, DVD, Disc select next folder: Use this
command to select the next folder on the MP3
or audio DVD.
CD, DVD, Disc select previous folder: Use this
command to select the previous folder on the
MP3 or audio DVD.
CD help, DVD help, Disc help: This command
instructs the system to assist with CD and
DVD commands.
Aux, Auxiliary: Use this command to select the
auxiliary device, when a device is connected.
OnStar® Command
OnStar: This command instructs the system to
connect to OnStar®. You will enter the OnStar®
voice recognition system. Refer to your OnStar®
manual for more information.
Voice Help
Voice help: This command will provide a
description of help commands that are available
to use.
89
✍ NOTES
90
A
Adding Destinations to the Address Book .......
Adding or Changing Preset Destinations ........
Alpha-Numeric Keyboard ................................
Audio System .................................................
Auto Reroute .................................................
D
42
42
17
60
26
C
Canadian Owners ............................................ 2
Canceling Guidance ....................................... 13
CD
Player ......................................................... 70
CD Messages ................................................ 76
CD Player ...................................................... 70
Cleaning the Video Screen ............................. 13
Database Coverage Explanations ...................
Destination .....................................................
Display ...........................................................
Driving on a Route .........................................
DVD
Player .........................................................
DVD Menu Options ........................................
DVD Messages ..............................................
DVD Player ....................................................
58
27
50
26
77
79
83
77
F
Finding a Station ............................................ 61
91
G
M
Getting Started, Navigation .............................. 6
Getting Started on Your Route ....................... 38
Global Positioning System (GPS) ................... 56
Guidance Volume ........................................... 13
Map Adjustments ............................................ 19
Map Scales .................................................... 19
Maps ............................................................. 18
H
Hard Keys ...................................................... 16
I
N
Nav (Navigation) ............................................ 44
Navigation
Getting Started ............................................. 6
System Overview .......................................... 4
Using the System ....................................... 16
Installing the Map DVD .................................. 18
L
Language — English/Metric .............................. 8
92
O
Ordering
Map DVDs .................................................. 58
Overview, Navigation System ........................... 4
Owners, Canadian ........................................... 2
P
Park Aid .........................................................
Playing a DVD ...............................................
Playing the Radio ...........................................
Problems with Route Guidance ......................
S
51
78
60
57
R
Radio ....................................................... 44,
Radio Data System (RDS) .............................
Radio Menu ...................................................
Rear Vision Camera .......................................
Regional Maps ...............................................
60
67
65
51
18
Scrolling the Map ........................................... 20
Setting the Search Area, Entering an
Address and Point of Interest, and Storing
Preset Destinations ....................................... 9
Setting the Time ........................................ 9, 51
Sound ............................................................ 44
Sound Menu .................................................. 63
Storing Preset Stations ................................... 63
Storing Radio Station Presets .......................... 8
Symbols ......................................................... 20
System Needs Service, If ............................... 58
93
T
Touch-Sensitive Screen Buttons ..................... 17
Traveling Across Regions ............................... 27
U
Using an MP3 CD .......................................... 72
Using Your Stored Preset Destinations ........... 12
V
Vehicle Positioning .........................................
Video Screen, Cleaning ..................................
Voice Recognition ..........................................
Voice Recognition Commands ........................
56
13
86
87
X
XM™ Satellite Radio Service ......................... 68
94
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising