TouchKit TouchScreen Controller User Guide
Below you will find brief information for TouchScreen Controller. This guide provides instructions on installing, configuring, and using the TouchKit TouchScreen Controller for Windows 9X/ME.
Advertisement
Advertisement
TouchKit TouchScreen Controller
User Guide for Windows 9X / ME
Version: 3.2.1
TouchKit Guide for Win9X/ME v3.2.1
1
Chapter 1. Installing and using TouchKit
TouchKit is software, which contains drivers of the touch panel controllers for the
specified communication connectors, RS232, PS/2 and USB, and the other two utilities:
· Touch Tray support
This is utility for emulating the right and left button of mouse through controlling touch panel. Users can toggle between right or left mouse buttons by this utility.
· Configuration support
The calibration and draw test of touch panel are done by this utility. Besides, users can add or remove for new RS-232, PS/2 or USB touch panel devices.
Follow these steps to install TouchKit.
1. Put the TouchKit CD to CD-ROM.
2. Change directory to Win9X_ME
3. Double click the Setup.exe, then windows starts to run the installation program.
Notice that do not plug the USB controller on the system before the installation has been finished.
4. Just click [Next >] button to continue installation.
TouchKit Guide for Win9X/ME v3.2.1
2
5. Then check the check box if PS/2 touch controller is to be installed. The default is unchecked. Then Press [Next >] to continue installation.
System will give you a warning, if users check the PS2AUX check box,
6. Choose the setup type that best suits your needs. There are two TouchKit accessory utilities for choosing, Rotation Monitor Utility and Shutdown Utility. Users can install the utility they want by checking the box. Then Press [Next >] to continue installation.
TouchKit Guide for Win9X/ME v3.2.1
3
7. Select the appropriate folder where set-up files will be installed. Then Press [Next >] to continue installation.
8. Then type in the name of program folder for TouchKit or press [Next >] to continue.
There will be a default name for it.
During driver installation, the setup program will scan COM port for RS232 Touchkit controller. Once the controller was scanned, the setup program will display a dialog as
Click Yes to add the controller on the specified COM port automatically.
TouchKit Guide for Win9X/ME v3.2.1
4
9. Windows is copying files to disk and the setup is complete. It will request re-boot computer. Press [Yes >] to re-boot immediately or [No >] to re-boot later. The installation will not be finished until system re-boot.
10. Setup is complete. After TouchKit installation, the USB device will be found automatically as soon as it was plugged into the computer. Then users can see the new device on the application program window. And, the program will remove the USB
Device automatically as soon as it was unplugged. ( USB device is not supported for
Windows95 )
TouchKit Guide for Win9X/ME v3.2.1
5
Chapter2. Configuration Utility and Right Button Emulator
There are five property pages in TouchKit utility, and they are General, Setting,
Edge coefficient, Monitors and About. Each property page contains different functions for users to do the adjustments. Therefore, users can easily manage all the TouchKit controllers through TouchKit Utility.
Functional Group Tab
General
General property page contains the functions of language selection, devices add/
remove, 4 points calibration, Draw test and Advanced.
General Function
TouchKit Guide for Win9X/ME v3.2.1
6
<Language>
TouchKit supports multi-language user interface. Users could select native
language that is compatible to operation system support. For example, if the operation system is a traditional Chinese version, users could see the normal display words under the traditional Chinese and English mode. There are ten different languages, English, Traditional Chinese, Simplified
Chinese, French, Spanish, German, Japanese, Italian, Korean and
Dutch supported in this feature of TouchKit.
Note to select the compatible language first.
Select the compatible language first or users may not see the normal display of each button.
<Add> / <Remove>
Please check the touch panel devices (including its controller) are equipped well, then click [Add] button to add all of those RS-232 and PS/2 devices to the Panel List dialogue box.
There is one devices found. Press [Yes] to continue.
TouchKit Guide for Win9X/ME v3.2.1
7
Device is found in COM1
The controller is displayed on the Panel List box. users can get the information of interface, type, firmware version and baud rate for each controller.
Select one device after added more than one device at the panel list window.
The one selected will activate the panel, and remember to do the calibration before starting to use touch panel.
But, for hot-swapping USB touch controller, it will be added automatically as soon as it was plugged into the computer. Then users can see the new device on the application program window. And, the program will remove the USB touch controller automatically as soon as it was unplugged. ( USB device is not
supported for Windows95 )
TouchKit Guide for Win9X/ME v3.2.1
8
There are three buttons, [4pts Cal] [Draw Test] [Advanced], at the lower section of the
General property page.
<4pts Cal>
Correct 4 point locations on screen with the panel. Press [4 pts Cal], screen displays as follows.
Touch the blinking symbol on panel until beep or stop blinking.
TouchKit Guide for Win9X/ME v3.2.1
9
<Draw Test>
Test the drawing position related to the display screen on panel.
Click on the [Draw Test] button. There will be a squared blue display showing.
In drawing test window, users can click [Clear] button to clear the window. Also, users can click [Quit] or press mouse right button to quit from the drawing test.
In drawing test window, users can verify the panel linearity, calibration capability, and drawing line quality.
<Advanced>
Touchkit provide more accuracy 25 points calibration for touch sensor. In addition,
Touchkit provides controller setting for capacitive touch sensor. If the capacitive
controller is selected, a capacitive setting property page appears on the advanced sheet. In general case, it does not need to do 25 points calibration other then bad linearity sensor.
Press [Clear] to clear the previous calibration records.
TouchKit Guide for Win9X/ME v3.2.1
10
Press [Yes] to clear previous records.The record will become default record.
Press [25ptCal] to do 25 points calibration. Correct 25 point locations on screen with the panel.
Touch the blinking symbol on panel until beep or stop blinking.
After the calibration, the new record will overwrite the old one.
If the selected controller is capacitive type, an extra property page for capacitive setting adjustment shown as below:
Please select property size of capacitive screen first, and press [Restart]
TouchKit Guide for Win9X/ME v3.2.1
11
The capacitive controller will restart, and do not touch the screen before the warning message disappears
Warming: Do not adjust the sensitive and sampling time without RD help
Setting
There are three functional groups in Setting property page, and at the upper section of the property page is sound option; at the middle section is Mouse Mode; and at the lower section is Double Click Adjustment.
The Sound options provide users the click feedback while touching the panel.
Select preferred option first.
Sound options
<No Sound>
Users could choose to make no sound while using the touch panel.
<Touch Down>
The system will make a sound while touching the panel.
<Lift Up>
The system will not make any sound until finger leaves the touch panel.
<Frequency>
Sound frequency, drag the cursor from left to right is low to high.
<Duration>
Sound duration, drag the cursor from left to right is short to long.
TouchKit Guide for Win9X/ME v3.2.1
12
The Mouse Mode provides users different operating options. They are as follows:
Mouse Mode
<Mouse Button>
Click it to show / hide Touch Tray on the right bottom corner of the desktop. The touch panel system starts with the computer booting, and a mouse icon shows in the taskbar.
Users can choose show or hide Touch Tray from the mouse icon in the taskbar. Just click the mouse icon to choose show or hide.
Touch Tray
Change right / left button by clicking the upper small rectangular box of Touch Tray.
Blue area expresses what button has been selected.
TouchKit Guide for Win9X/ME v3.2.1
13
<Shutdown utility>
Shutdown utility
Click on shutdown utility in the task bar
Shutdown utility dialog
There are five modes in shutdown utility for users convenience.
[Standby] to enter standby mode that saves power consumption.
[Shutdown] to turn off PC.
[Reboot] to restart PC.
[Cancel] to escape from the Shutdown utility dialog.
[Exit] to disable the Shutdown utility.
<Mouse Mode>
There are three kinds of mouse mode users could choose,
[Normal Mode]
It provides all the mouse functions, including the dragging function.
[Click on Touch]
Click action is executed as soon as users touch the panel.
[Click on Release]
Click action will not be executed until finger leaves the panel.
TouchKit Guide for Win9X/ME v3.2.1
14
<Option>
Touchkit provides an option for advanced Mouse Emulation setting. When the
Option button is pressed, a setting property sheet will be popped up. Support
Constant Touch and Support Auto Right Button check boxes are shown in the property sheet to enable / disable Constant touch and Auto right button support.
[Constant Touch]
Enable Constant Touch to force driver to stop reporting touch point when the movement is small. Therefore, the user can see a stabilized cursor instead of a chattering cursor when users touch the same point with unwanted noise.
[Auto Right Button]
Enable Auto Right Button to force driver to report a right click mouse event to OS when users lift up from a constant touch. It no longer needs to touch the right
button in the touchtray to activate a right click. This feature makes users to do right
click more easily with touchscreen.
TouchKit Guide for Win9X/ME v3.2.1
15
<Cursor Visibility>
Cursor visibility function provides users to hide the cursor in the display. Please go to
Start / Control Panel / Mouse / Pointers / Scheme, and choose TouchKit Hide
Cursor. Press [Apply] to make setting change, and press [OK] to escape the property page.
If users want to cancel the function of TouchKit Hide Cursor, do the steps again and choose the other scheme.
TouchKit Guide for Win9X/ME v3.2.1
16
The Double Click adjustment provides users to set up the tolerance while double clicking.
They are as follows:
Double Click Adjustment
<Double Click Speed>
Double Click Speed is the double click response time for Windows system. Users can adjust the proper double click for easy double click by touch panel.
<Double Click Area>
Each one touch has its own touch tolerance once someone may not fix in one point.
So if users set the Double Click Area to <Smaller>, the panel will be very sensitive about micro-move while users want to fix on a point. If users set it to <Larger>, it tolerates the larger touch point movement while users want to point at a fixed position.
TouchKit Guide for Win9X/ME v3.2.1
17
Edge Coefficient
Edge Coefficient property page contains the functions of Edge Compensation for Top,
Bottom, Left, Right, X Axis and Y Axis.
In some case, if it is difficult to touch items at the edges of the touch panel, users can set adjustment to reach the edges of the screen image.
<Top>
If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position of the top edge. If users set the Edge to <Larger>, TouchKit will extend the horizontal position of the top edge.
<Bottom>
If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position of the bottom edge. If users set the Edge to <Larger>, TouchKit will extend the horizontal position of the bottom edge.
<Left>
If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of the left edge. If users set the Edge to <Larger>, TouchKit will extend the vertical position of the left edge.
<Right>
If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of the right edge.
If users set the Edge to <Larger>, TouchKit will extend the vertical position of the right edge.
TouchKit Guide for Win9X/ME v3.2.1
18
In some case, cursor will be behind the finger when users touch the panel. If users can not see the cursor when they touch down on the panel, users can set
X Axis or Y Axis to move the cursor.
<Offset X Axis>
If users set the Offset X Axis to <Smaller>, cursor will be moved a pixel of
X Axis to left. If users set the Offset X Axis to <Larger>, cursor will be moved a pixel of X Axis to right.
<Offset Y Axis>
If users set the Offset Y Axis to <Smaller>, cursor will be moved a pixel of
Y Axis to top. If users set the Offset Y Axis to <Larger>, cursor will be moved a pixel of Y Axis to bottom.
Edge Compensation Switch
<Edge Compensation Switch>
Users can choose Edge compensation Enable / Disable from left bottom corner of Touchkit Utility.
Using +10% and -10% button to adjust the smaller or larger of edge. If users press +10% button, the top, bottom, left and right edges will extend
10% of orientation to touch screen, and cursor will be moved 10 pixel of X and Y Axis to right and top. If users press -10% button, the top, bottom, left and right edges will contract 10% of orientation to touch screen, and cursor will be moved 10 pixel of X and Y Axis to left and bottom.
If users want the value back to the default value, choose Default button.
TouchKit Guide for Win9X/ME v3.2.1
19
Monitors
There are three functions in this property page, and they are Multiple Monitors, Split
Monitor and One point Calibration. Such a trendy and yet innovated design provides viewing pleasures, viewing flexibility and convenience to users.
<Multiple Monitors>
To configure the mapping relationship between the monitors and the touch panels, select the monitor page as below.
Set the check box (Use Multiple Monitors) to enable multiple monitors mapping.
Uncheck this box will disable multiple-monitor configuration, and all of the touch panel controllers will be mapped to the primary monitor. The gray shadow area is the monitor mapped the selected controller/panel. The button [Mapping] is used to find the mapping relationships between the monitors and touch panel controllers. Press the [Mapping], the software will guide users to touch the corresponding monitor to obtain the mapping relationship.
After finish monitor mapping, Press [Apply] to apply the mapping relation.
TouchKit Guide for Win9X/ME v3.2.1
20
<Split Monitors>
To use the Split Monitor function, users need to select which controller you want to launch this function, then check the Multiple Monitors box and Split Monitor at the same time as showing as the follow picture. Press the [Split Setting] button to set up the activate area.
It shows the current resolution of display and users can set up the activate area by inputting the value by yourself or use the default button [Upper Half], [Left Half] or
[Quarter]. The default value of panel resolution should be full screen as Left: 0 , Right:
0, Top: 0 and Bottom: 0.
<One Point Calibration>
Touchkit utility provides a fast tool to identify the touchscreen orientation when the
monitor display was rotated by 90 degrees. Enable this One Point Calibration feature,
Touchtray will pops up this One Point Calibration tool for users to identify and correct
the touchscreen / monitor orientation whenever the monitors was rotated by 90 degrees.
Disable this feature, Touchtray does not pop up this One Point Calibration tool. Then, the user has to do four points calibration to correct the orientation whenever the monitor was rotated.
TouchKit Guide for Win9X/ME v3.2.1
21
About
Information about TouchKit.
TouchKit Guide for Win9X/ME v3.2.1
22
Chapter3. MONITOR ROTATION SETTING
TouchKit driver package for Windows 98/ME/2000/XP provides two easiest ways to rotate the touch panel while the display is rotated. l Rotating display by way of nVidia or ATI driver l Rotating display by way of Pivot.
3.1
Rotating display by way of nVidia or ATI driver
1. After activating the rotation of nVidia or ATI driver, there will be one blinking symbol show as the following picture. Touch near the blinking symbol until stop blinking, and the touch panel will rotate itself.
One touch blinking symbol adjustment
2. However, 180 degree rotation of touch panel can not be done in one step, users need to rotate 90 degree twice.
TouchKit Guide for Win9X/ME v3.2.1
23
3.2 Rotating display by way of Pivot
There are two ways to rotate the display by way of Pivot. l Rotating display by way of Pivot hotkey or function menu l Rotating display by way of RotTray icon provided by TouchKit.
< Rotating display by way of Pivot hotkey or function menu >
1. To rotate the display, please install Pivot pro 6.05 first. Then reboot PC to activate
Pivot.
2. There will be a pivot icon in the task bar. Users can click on it, and users can choose four angles: 0 degree, 90 degree, 180 degree, 270 degree to rotate the display.
3. After choosing the angle users want to rotate, there will be one blinking symbol showing as the following picture. Touch this blinking symbol until stop blinking, and the touch panel will rotate itself.
One touch blinking symbol adjustment
4. However 180 degree rotation of touch panel can not be done in one step, users need to rotate 90 degree twice.
TouchKit Guide for Win9X/ME v3.2.1
24
< Rotating display by way of RotTray icon provided by TouchKit>
1. To rotate the display, please install Pivot pro 6.05 first. Then reboot PC to activate
Pivot.
2. Users will see RotTray icon in the task bar.
RotTray
RotTray icon
3. Clicking on RotTray, it will call Pivot to rotate the display and touch panel 90 degree at the same time. Clicking it again, it will rotate another 90 degree to 180 degree. Every click on RotTray, display will rotate clockwise. Recalibration and one symbol
4. However this version of RotTray is design for Pivot pro 6.05. If users want to use older version of Pivot, like Pivot 5.1, users need to amend the value of windows registry. The next step is an example for setting Pivot 5.1 on Win98.
5. Go to Start / Run, and execute regedit.
Press [OK] to execute
6. For Windows 95/98/ME OS, The Registry Editor will show as the follow picture. Then go to HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\VxD\TKIT.
Right click on the MaxRotation, and choose Modify.
TouchKit Guide for Win9X/ME v3.2.1
25
“FFFFFFFF”.
Right click on MaxRotation to Modify Value data
Pressing [OK] to confirm.
8. Here bellow are the value data for different version of Pivot:
Version of Pivot
Pivot pro 6.05
Pivot 5.1
Other Version
Available Angle
0, 90, 180, 270
0, -90
0, 90
Value Data
4 (default)
FFFFFFFF
2
TouchKit Guide for Win9X/ME v3.2.1
26
Chapter 4. Uninstalling TouchKit
Follow these steps to uninstall TouchKit.
1. Go to Start / Programs / TouchKit / Uninstall, and execute it.
2. TouchKit setup dialog appears, and prepares to uninstall.
3. Confirm dialog, press [OK] to start un-installation; [Cancel] to cancel uninstallation.
TouchKit Guide for Win9X/ME v3.2.1
27
4. Start to uninstall TouchKit.
If users do not want to uninstall TouchKit at this moment, press [Cancel] to terminate the uninstall process.
5. TouchKit will not be removed until system re-boot. Press [Yes] to re-boot immediately or [No] to re-boot later.
TouchKit Guide for Win9X/ME v3.2.1
28

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Driver for TouchScreen Controller
- Touch Tray support
- Configuration utility
- Right Button emulator
- Multiple Monitors support
- Pivot rotation support
- System-wide shutdown utility