Camco | P.9 Series | User manual | Camco P.9 Series User manual

Camco P.9 Series User manual
Q-POWER
Q-POWER SERIES USER MANUAL
SERIES
INFORMATION FOR USE FOR MODELS
Q-POWER 4, Q-POWER 6 and Q-POWER 10
QUM_GB_2008-2009-R4_06-2009
© Copyright 2008 by CAMCO Produktions- und Vertriebs-GmbH
für Beschallungs- und Beleuchtungsanlagen
Fischpicke 5, D-57482 Wenden, Germany
Telephone +49 (0) 2762 408-0
Q-POWER
SERIES
P. USER MANUAL
Q - P O W E R SERIES
Q-POWER
IMPORTANT SAFETY INSTRUCTIONS
SERIES
IMPORTANT SAFETY INSTRUCTIONS
1) Read the information for use (user manual).
2) Please keep this user manual in a safe place during the lifetime of the amplifier. The user manual forms an integral part of the amplifier. Reselling of the
amplifier is only possible if the user manual is available. Any changes made to
the amplifier have to be documented in writing and passed on to the buyer in
the event of resale.
3) Heed all warnings.
4) Follow all instructions.
5) Do not expose this device to rain or moisture. Do not use this amplifier near
water (for example, swimming pools and fountains). Do not place any objects
containing liquids, such as bottles or glasses, on the top of the unit. Do not splash
liquids on the unit. IP-20 equipment. No Protection against splashing water.
11) Do not place this amplifier on an unstable cart, stand,
tripod, bracket or table. The device may fall, causing
serious injury and serious damage to the device itself.
12) The amplifier can only be disconnected from the power supply by removing
the plug which must be freely accessible at all times. Unplug this amplifier
during lightning storms or when unused for long periods of time.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the user
manual.
8) Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatuses that produce heat.
9) Protect the power cord from being walked on, pinched or damaged in any
other way. Pay particular attention to plugs and the point where they exit from
the amplifier.
P. 10) The amplifier may only be used in accordance with the information provided
in the user manual. Before and during the usage of the amplifier please ensure
that all recommendations, especially the safety recommendations as detailed in
the user manual, are adhered to.
The Q-POWER Amplifier is designed for the amplification of pulsed audio signals
and the amplifier should only be connected to speakers with an average impedance as indicated.
USER MANUAL
Q - P O W E R SERIES
13) Refer all servicing to qualified service personnel.
Servicing is required when
the power-supply cord or plug has been damaged,
liquid has been spilled or objects have fallen into the amplifier,
the amplifier has been exposed to rain or moisture,
the amplifier has been dropped or suffered damage in any other way,
the amplifier exhibits a distinct change from its normal function or
performance.
Q-POWER
EXPLANATION OF SYMBOLS / SAFETY
SERIES
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION – HIGH VOLTAGE HAZARDS
EXIST WITHIN THIS PRODUCT.
REFER ALL SERVICING TO
AUTHORISED PERSONNEL.
THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS
VOLTAGE WITHIN THE PRODUCT’S ENCLOSURE.
THE EXCLAMATION MARK IS INTENDED TO ALERT THE USER
TO IMPORTANT INSTRUCTIONS ALSO FOR MAINTENANCE IN THE
LITERATURE ACCOMPANYING THE AMPLIFIER.
THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL ALERTS
THE USER TO DANGEROUSLY HIGH VOLTAGE AT THE SPEAKON
CONNECTORS THAT COULD POTENTIALLY BE LIFE THREATENING.
CAUTION – RISK OF ELECTRIC SHOCK – DO NOT OPEN.
WARNING – TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
AMPLIFIER TO RAIN OR MOISTURE.
THE AMPLIFIER MAY ONLY BE CONNECTED
TO A SOCKET WITH A PROTECTIVE EARTH CONDUCTOR.
P. USER MANUAL
Q - P O W E R SERIES
1. Read the information for use (user manual)
When shipping the Q-POWER amplifier always use the original shipping carton
and packing materials. For maximum protection repack the unit as it was originally packed at the factory.
2. Environments
Use this amplifier only in E1,E2,E3,E4 or E5 environments according to EN55103-2
“Electromagnetic compatibility – Product family standard for audio, video and
audio-visual and entertainment lighting control apparatus for professional use
– Part 2: Immunity”
3. Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the amplifier and to protect it from overheating. These openings must not be blocked or covered. This amplifier should not be installed
unless proper ventilation is provided or manufacturer’s instructions have been
adhered to.
4. Water and Moisture
Do not expose this device to rain or moisture. Do not use this amplifier near
water (for example, swimming pools and fountains). Do not place any objects
containing liquids, such as bottles or glasses, on the top of the unit. Do not splash
liquids on the unit. IP-20 equipment. No Protection against splashing water.
5. Cleaning
Unplug this amplifier from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners.
6. Power-cord Protection
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon them or against them, paying particular
attention to cords and plugs and the point where they exit from the amplifier.
Q-POWER
SAFETY
SERIES
7. Lightning
For added protection of this amplifier during lightning storms or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the amplifier due to lightning and power-line
surges. Disconnection from the mains power supply can only be achieved by
removing the plug from the mains socket and by external disconnecting all
poles from the mains.
8. Interference of external objects and/or liquids with the appliance
Never push objects of any kind into this amplifier through openings as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the amplifier.
9. Accessories
Do not place this amplifier on an unstable cart, stand, tripod, bracket or table.
The amplifier may fall, causing serious injury and serious damage to the product.
Any mounting of the amplifier should follow the manufacturers instructions and
should use a mounting accessory recommended by the manufacturer.
10. Connecting
When you connect the amplifier to other equipment turn off the power and
unplug all of the equipment from the supply source. Failure to do so may cause
an electric shock and serious personal injury. Read the user manual of the other
equipment carefully and follow the instructions when making the connections.
11. Sound Volume
Reduce the volume to minimum before you turn on the amplifier to prevent
sudden high levels of noise which may cause hearing or speaker damage.
(See also section 4.2.1 Volume control)
P. USER MANUAL
Q - P O W E R SERIES
12. Damages that require service
Unplug this amplifier from the mains supply and refer to your dealer/distributor
or other authorised repair workshop if any of the following situations occur:
if liquid has been spilled or objects have fallen into the amplifier
if the amplifier does not operate normally as described in the user manual,
operate the controls only as described in the user manual
if the amplifier has been dropped or damaged in any other way
when the amplifier exhibits a distinct change from its normal function or
performance
13. Servicing
Do not attempt to service this amplifier yourself. As opening or removing covers
may expose you to dangerous voltage or other hazards, the amplifier may only
be opened by qualified personnel. Please refer to your dealer/distributor.
14. Servicing and Replacement Parts
All service and repair work must be carried out by a CAMCO authorised dealer.
When replacement parts are required, please ensure that the dealer/distributor only uses replacement parts specified by the manufacturer. The use of un­
authorised replacement parts may result in injury and/or damage through fire
or electric shock or other electricity-related hazards.
15. Safety Check
Upon completion of any service or repairs to this product, ask the dealer/
distributor to perform safety checks to determine that the amplifier is in proper
operating condition.
Recommendations on how to carry out the safety test can be found in
DIN VDE 0701-1 “Maintenance, Modification and Test of Electronic Appliances“.
Q-POWER
SERIES
EC DECLARATION OF CONFORMITY
EC Declaration of Conformity in accordance to EC Directives:
electro-magnetic compatibility (Council Directive 2004/108/EC);
low-voltage electrical equipment (Council Directive 73/23/EEC )
Manufacturer´s Name:
CAMCO Produktions- und Vertriebs-GmbH
für Beschallungs- und Beleuchtungsanlagen
Manufacturer´s Address:
Fischpicke 5, D-57482 Wenden, Germany
Declares that the product with the model name:
CAMCO Power amplifier Q - P O W E R 4, Q - P O W E R
Conforms to the following standards:
EN60065 Safety
EN55103-1 Emission
EN55103-2 Immunity
The operating conditions and application environments presupposed in the
information for use (user manual) are to be kept accordingly.
Wenden, 15.12.2007
Joachim Stöcker
P. 6 and Q - P O W E R 10
USER MANUAL
Q - P O W E R SERIES
Q-POWER
CONTENTS
SERIES
P. 2
P. 3
P. 5
P. 6
P. 7
P. 8
P. 9
P. 10
P. 11
P. 12
P. 13
P. 15
P. 16
P. IMPORTANT SAFETY INSTRUCTIONS
EXPLANATION OF SYMBOLS / SAFETY
EC DECLARATION OF CONFORMITY
CONTENTS
1 WELCOME
1.1 Welcome to CAMCO
1.2 Unpacking
1.3 The Amplifier
2 FACILITIES
2.1 Q-POWER – The Front
2.2 Q-POWER – The Rear
2.3 Factory Settings
3 INSTALLATION
3.1 Mains Supply
3.2 On/Off Switch
3.3 Mounting
3.4 Cooling
3.5 Wiring
3.5.1 Input Connectors
3.5.2 Output Connectors
4 OPERATION
4.1 Indicators
4.1.1 On LEDs
4.1.2 Signal / Protect LEDs (multifunctional)
4.1.3 I-Out LEDs
4.1.4 Clip LEDs
4.2 Controls
4.2.1 Volume Control
4.2.2 Gain selector
4.2.3 Limiter Switch
4.3 Power Amp Protection Systems
4.3.1 Clip Limiter
USER MANUAL
Q - P O W E R SERIES
P. 17
P. 18
P. 19
P. 20
P. 22
P. 24
P. 27
P. 28
P. 29
P. 30
4.3.2 SOA Protection
4.3.3 DC Protection
4.3.4 DC Servo
4.3.5 Over Current Protection
4.3.6 Thermal Protection
4.4 Mains Protections
4.4.1 Inrush Current Limitation
4.4.2 Mains Over Voltage Detection
4.4.3 Mains Failure Detection
4.4.4 Fuse Protection
4.5 Main SMPS Protections
4.5.1 Over Current Protection
4.5.2 Thermal Protection
4.6 Fans
4.7 Filter Cleaning
4.8 Mounting the Volume Control Security Cover
5 TROUBLESHOOTING
5.1 Problem: No Sound
5.2 Problem: Distorted Sound
5.3 Problem: Hiss
5.4 Problem: Squeals and Feedback
6 SPECIFICATIONS
7 MEASUREMENTS
8 WARRANTY INFORMATION
8.1 Summary Of Warranty
8.2 Items Excluded From This Warranty
8.3 What CAMCO Will Do
8.4 How To Obtain Warranty Service
8.5 CAMCO’s Product Improvement
9 SERVICE INFORMATION
10 MAINTENANCE INFORMATION / 11 DECOMMISSIONING
COMPANY INFORMATION
Q-POWER
1 WELCOME
SERIES
1.1 Welcome to CAMCO
Established in 1983, CAMCO has gained worldwide experience with professional
sound reinforcement technology. Within the audio market CAMCO specialises
in the production and marketing of high quality power amplifiers and sound
systems for use both on tour and in fixed installations.
The success of the LA, DL, DX, VORTEX and TECTON series of power amps has
made the CAMCO name synonymous with professional quality, high performance and utterly reliable power amps.
CAMCO’s commitment to research and development, seen not just in the area
of materials and technology but also most importantly in its highly skilled and
motivated workforce, is one of the keys to its ongoing success.
With its all-new Q-POWER amp series, CAMCO is pioneering a new dimension
in professional power amp construction. The seamless combination of groundbreaking technology with proven safety elements is the hallmark of the new
series.
Welcome to the new world of professional power amplifiers –
WELCOME TO CAMCO!
P. USER MANUAL
Q - P O W E R SERIES
1.2 Unpacking
Please unpack and inspect your new amplifier for any damage that may have
occurred during transit. If damage is found, notify the transportation company
immediately. Only you the consignee may initiate a claim for shipping damage.
CAMCO will be happy to cooperate fully as needed. Please save the shipping
carton as evidence of damage for the shipper’s inspection.
Even if the amplifier has arrived in perfect condition, save all packing materials
so you will have them if you ever need to transport the unit.
NEVER SHIP THE AMPLIFIER WITHOUT THE ORIGINAL
PACKING MATERIALS.
When shipping the Q-POWER amplifier, always use the original shipping carton
and packing materials. For maximum protection, repack the unit as it was originally packed at the factory.
Q-POWER
1 WELCOME / 2 FACILITIES
SERIES
1.3 The Amplifier
The Q-POWER-series amplifiers offer a power output of:
Q-POWER 4
1 kW peak per channel @ 4 Ω, using a Bipolar class H (2-step) high efficiency power amplifier output stage
Q-POWER 6
1,5 kW peak per channel @ 4 Ω, using a Bipolar class H (2-step) high efficiency power amplifier output stage
Q-POWER 10 2,5 kW peak per channel @ 4 Ω, using a MOSFET class D high efficiency power amplifier output stage
2 Facilities
1
2
5
2.1 Q-POWER – The Front
1 Clip LEDs
2 I-Out LEDs
3 Signal LEDs
4 On LEDs
P. USER MANUAL
Q - P O W E R SERIES
The dual-voltage feature of the Q-POWER amplifiers senses the mains before
startup and automatically sets the SMPS to the appropriate voltage (120 V or
230 V). No manual voltage setting will be necessary.
4
3
6
The Q-POWER-series amplifiers are fitted with dual voltage Switched Mode
Power Supplies (SMPS), which significantly reduce the weight and size
(only 2U) of the amplifiers. Using SMPS, the symmetrical supply voltages of the
power amplifier are more stable than the power supplies used in conventional
amplifiers.
7
8
9
10
11
12
5 Volume Control Channel A
6 Volume Control Channel B
7 Volume Control Channel C
8 Volume Control Channel D
9 Removable Air Filter System
10 Cooling Air Inlet Vents
11 On/Off Switch
12 Optional Volume Control Security Cover (included)
Q-POWER
2 FACILITIES
SERIES
13
14
16
15
21
20
19
22
18
Q-POWER 6

120 / 230 V ~ 50 / 60 Hz 1600 W
1000 W / 4 Ohm
   
  
45800
  
30
17
26
25 28
27
24
29
2.2 Q-POWER – The Rear
13 Rating Plate
14 Cooling Air Outlet Vents
15 SPEAKON Outlet Channel A/B
16 SPEAKON Outlet Channel C/D
17 Barrier Strip Outlets Channel A B C D
18 XLR Input Channel A
P. USER MANUAL
Q - P O W E R SERIES
19 XLR Input Channel B
20 XLR Input Channel C
21 XLR Input Channel D
22 Gain Selector
23 Euroblock Input Channel A
24 Euroblock Input Channel B
25 Euroblock Input Channel C
26 Euroblock Input Channel D
27 Clip Limiter Switch Channel A/B
28 Clip Limiter Switch Channel C/D
29 Barrier Strip Security Cover
30 AC Power Cable
23
Q-POWER
2 FACILITIES
SERIES
2.3 Factory settings
Q-POWER amplifiers are delivered with the following factory settings:
5
Front panel:
11
On/Off Switch
5 - 8
Volume Control
6
7
11
8
The amplifier is switched off.
The volume is set to minimum.
21
Q-POWER 6

120 / 230 V ~ 50 / 60 Hz 1600 W
1000 W / 4 Ohm
   
  
45800
  
27
Rear panel
21 Gain Selector
26 Clip Limiter Switch Channel A/B 27 Clip Limiter Switch Channel C/D P. 10
USER MANUAL
Q - P O W E R SERIES
32 dB
Off
Off
26
Make sure that the switches are set to the configuration needed for each
particular application.
Q-POWER
3 INSTALATION
SERIES
3.1 Mains supply
When mounting or connecting the amplifier always disconnect it from
mains. Only connect the Q-POWER amplifier to an appropriate AC circuit
and outlet, according to the requirements indicated in the second line on
the rating plate.
Q-POWER 4


120 / 230 V ~ 50 / 60 Hz 1200 W
   
800 W / 4 Ohm
  

45800
  
3.2 On/Off switch
The On/Off switch is a rocker-type switch. It is located on the right side of the
front panel. To turn the amplifier on, push in on the upper part of the switch. This
initiates start-up by activating the inrush current limiter. During power up the
clip and signal LEDs will light up in red for a few seconds. To turn the amplifier
off, push in on the lower part of the switch.
Q-POWER 6
120 / 230 V ~ 50 / 60 Hz 1600 W
   
1000 W / 4 Ohm
  
45800
  
Q-POWER 10
120 / 230 V ~ 50 / 60 Hz 1500 W
1800 W / 4 Ohm
   
  
45800
The amplifier is switched on.
  
Exemplary rating plates for a mains supply of 120 / 230 V ~ 50 / 60 Hz.
NOTE: This switch does NOT disconnect the amplifier from mains.
Power Supply Data:
The switch initiates start-up by activating the current limiting function. As soon
as the power amplifier is connected to the mains power supply, a voltage is
supplied to both the line-filter and the fused input of the controllable rectifier.
Disconnecting the amplifier from the main power supply can only be achieved
by physically separating the amplifier from the mains by pulling the mains plug.
The mains plug therefore has to be freely accessible. Disconnect the mains plug
from the mains during a lightning storm or when the amplifier remains unused
or un-supervised for a prolonged period of time. Alternatively, you can disconnect the amplifier via an external all-pole disconnection from the mains.
Voltage
Q-POWER 4 120 / 230 V ~
Q-POWER 6 120 / 230 V ~
Q-POWER 10 120 / 230 V ~
Frequency
50 / 60 Hz
50 / 60 Hz
50 / 60 Hz
Current
15 / 8,5 A
22 / 12 A
21 / 11 A
Power Consumption
1200 W
1600 W
1500 W
NOTE: Only fixed 120 V or 230 V operation is possible. The amplifier should not
be permanently operated at voltages not within the specified range (rated voltage ±10 %), as this might affect the overall performance.
NOTE: The rated power consumption and mains current draw is measured at 1/8
of the rated output power (i.e. 4 x 100 W for the Q-POWER 4, 4 x 125 W for the
Q-POWER 6 and 4 x 225 W for the Q-POWER 10) with pink noise to represent
typical music signal. The mains current and power consumption can be considerably higher (or lower) depending on the effective output power.
P. 11
The amplifier is switched off.
USER MANUAL
Q - P O W E R SERIES
If a power cut occurs while the amplifier is switched on, it will restart auto­
matically once the power supply has been restored. All settings prior operation
to the loss of power will be maintained.
Q-POWER
88,10 mm
10,50 mm
7,00 mm
3.3 Mounting
Use four screws and washers when mounting the amplifier to the front rack rails.
For mobile use, the amplifier should also be secured using the 19” mounting
elements on the rear panel.
76,20 mm
3 INSTALLATION
SERIES
465,00 mm
P. 12
USER MANUAL
Q - P O W E R SERIES
412,00 mm
421,00 mm
433,00 mm
Q-POWER
3 INSTALLATION
SERIES
3.4 Cooling
Under normal operation of the power amp, overheating should never be a
problem. The air is taken in from the front and out through the back. It is of
course essential that while the power amp is running air is able to circulate
around it freely.
The efficiency of the cooling will depend on the immediate environment (e. g.
an enclosed rack, direct sunlight) and on whether the front filter is clogged. If
the amp is installed in a case the open area at the back of the case must be at
least 140 cm². This area should be in line with the amp.
If this cannot be achived a forced ventilation system has to be used.
Input D
Input C
Input B
Input A
-
-
-
-
+
3
+
3
2
+
3
2
+
3
2
2
In D
In C
In B
In A
Input D
Input C
Input B
Input A
3.5 Wiring
3.5.1 Input Connectors
+
XLR:
Pin 1 = Ground
Pin 2 = Hot (inphase, +)
Pin 3 = Cold (out of phase, -)
Euroblock connector:
Pin 1 = Hot (inphase, +)
Pin 2 = Ground
Pin 3 = Cold (out of phase, -)
-
Make sure to always use high-quality symmetrical (balanced) shielded cable to
ensure maximum audio quality.
Please do not simultaneously attach two independent signal sources to the XLR
and Euroblock input connectors of the same channel. This could lead to volume
and audio quality loss and could damage the connected signal sources.
P. 13
USER MANUAL
Q - P O W E R SERIES
2
In D
+
3
-
2
In C
+
3
-
2
In B
+
3
-
2
3
In A
3.5.2 Output Connectors
The two SPEAKON connectors are connected to the channel A to D power amplifier outputs. The pin configuration of the SPEAKON-connectors is as follows:
Top Right: Pin 1+
Pin 1-
Pin 2+
Pin 2-
Channel A signal +
Channel A signal -
Channel B signal +
Channel B signal -
Top Left:
Pin 1+
Pin 1-
Pin 2+
Pin 2-
Channel C signal +
Channel C signal Channel D signal +
Channel D signal -
Q-POWER
3 INSTALLATION
SERIES
The pin configuration of the Barrier Strip connector is as follows:
Top row from left to right:
(all signal +)
Channel D - Channel C - Channel B - Channel A
Bottom row from left to right:
(all signal -)
Channel D - Channel C - Channel B - Channel A
Wiring to the output connectors must conform to NEC Class 2 safety standards or its equivalent that meets all national and local electric codes.
For reasons of safety and performance, only use high-quality fully in­su­lated
speaker cables of stranded copper wire. Use the largest wire size that is economically and physically practical and make sure that the cables are no longer
than necessary.
A
B
C
D
2+ 2-
2+ 2-
1+ 1-
1+ 1-
SPEAKON connectors
2+ 2-
2+ 2-
1+ 1-
1+ 1-
+
Barrier Strip connectors
D
C
B
A
The, Q-POWER 6 and Q-POWER 10 amplifiers are optimised for a loudspeaker
impedance of 4 Ω . Especially the Q-POWER 4 can handle impedaces down to
2 Ω. Attaching lower impedances might affect audio quality and overall performance of the amplifier.
P. 14
USER MANUAL
Q - P O W E R SERIES
NOTE / IMPORTANT:
The Q-POWER 10 uses a bridged power amplifier output stage. This implies
that the signal - loudspeaker outputs are not (and must never be) directly
connected to the electrical ground (earth) or chassis of the amplifier!
Please make sure to always attach the loudspeakers only between the
signal + and the signal - outputs of the same channel on the SPEAKON or
Barrier Strip connectors.
WARNING !
The lightning flashes near the output connectors indicate high vol­tages
that are potentially life threatening.
Wiring to these terminals requires installation by an instructed person or
the use of ready-made leads or cords. Custom wiring should only be carried
out by qualified personnel.
To prevent electric shock, do not operate the amplifier with any of the conductor portion of the speaker wire exposed.
To connect any custom speaker cable wiring to the Barrier Strip connectors
remove the security cover which is held by two screws. Take care to reinstall
the security cover after all connections are made, and be cautious to avoid
short-circuits between the speaker wires and the security cover or chassis (for
example due to damaged or clamped cable isolations).
NOTE: Any damage to the loudspeaker or amplifier due to wrong cabling will
not be covered by warranty.
Q-POWER
4 OPERATION
SERIES
P. 15
4.1 Indicators
4.1.1 On LEDs
Under normal operation, after the amp has started, the green power LEDs are
permanently lit.
4.1.3 I-Out LEDs
The brightness is proportional to the output current in the channel.
4.1.2 Signal / Protect LEDs (multifunctional)
The green Signal LEDs are illuminated when the voltage level at the output
reaches approx. 4 V; this corresponds to a power of approx. 4 W into a 4 Ohm
load. The channel signal LEDs are illuminated red when the amplifier is in Protect
Mode (Mute), for example because of persistent DC-voltage at the outputs or
overheating.
4.1.4 Clip LEDs
This LED indicates an overloading of the amplifier when the power output level
is to high.
USER MANUAL
Q - P O W E R SERIES
Q-POWER
4 OPERATION
SERIES
4.2 Controls
4.2.1 Volume Control
A volume control with 41 notched settings controls the audio signal. These
settings have been selected to correspond to human hearing characteristics
(logarithmically) and therefore guarantee an optimal range of settings for
practical applications. Each channel can be set individually.
Set the volume to zero before turning on the amplifier to prevent the occurrence of sudden high volume levels which may cause damage to your hearing
and/or the speakers.
4.2.2 Gain Selector
A switch on the rear of the Q-POWER amplifiers allows the maximum amplification attainable to be set directly in the input stage.
The Q-POWER amplifiers have a 26 dB and 32 dB
voltage gain setting along with a 1,4 V sensitivity
setting.
4.2.3 Limiter Switch
This switch is located at the rear of Q-POWER amplifiers. It allows you to activate
the clip limiter function on the channels A/B and C/D respectively.
4.3 Power Amp Protection Systems
4.3.1 Clip Limiter
If the power amp is overdriven and the limiter is set to on (see section 4.2.3)
the clip detection triggers the Attack-Release-Circuit (ARC). The ARC delivers
the control voltage for the gain reduction.
P. 16
USER MANUAL
Q - P O W E R SERIES
4.3.2 SOA Protection
Whenever the power transistors leave their Safe Operation Area (SOA), the SOAprotection will either switch back the current rail of the respective channel
(Q-POWER 4 & Q-POWER 6) or limit the maximum load current in the power
transistors (Q-POWER 10).
4.3.3 DC Protection
Each output of the power amp is constantly monitored for persistent DC voltage
levels. If the 3 V thresholds are exceeded at any of the outputs, the corresponding channel will be muted. If DC was only applied for a short moment, the amplifier will release mute and work as normal. If DC is applied for longer periods or
several short times the amplifier will switch to standby mode.
Switch off the amplifier, wait until all indicator LEDs extinguish and switch the
amplifier on again.
4.3.4 DC Servo
To prevent DC Offset at the speaker output the Q-POWER amplifiers are fitted
with a DC Servo.
4.3.5 Over Current Protection
Over current is permanently controlled in the output stage. In case of exessive
loading the maximum output current of the amplifiers is automatically limited.
This improves reliability without degrading sound quality when driving complex loads.
4.3.6 Thermal Protection
There are sensors in each amplifier heatsink in order to ascertain tem­perature
data. If a temperature of more than 85 °C is detected at the heat sinks, the input
signal on that channel is reduced proportionally to prevent further heating of
the amplifier. If the temperature exceeds approximately 100 °C, the main SMPS
is switched off(safety shut-off ).
Q-POWER
4 OPERATION
SERIES
4.4 Mains Protections
4.4.1 Inrush Current Limitation
Within approximately 2 seconds of the Q-POWER Amplifier being switched on,
the inrush current limiter will increase mains current smoothly from nearly zero
to nominal value. This value de­pends on program material, output level and
speaker loads.
4.5 Main SMPS Protections
4.5.1 Over Current Protection
The main SMPS (Switched Mode Power Supply) transformer current of your
Q-POWER Amplifier is continuously monitored. If over current occurs the main
SMPS immediately stops working. Should there be an internal failure this feature
prevents other parts from being damaged.
4.4.2 Mains Over Voltage Detection
Mains Over Voltage Detection is always operative. When the mains voltage
­exceeds approx. 263 V (230 V operation) or 137 V (120 V operation), the amplifier will switch off. When the mains voltage returns to nominal value a soft start
occurs.
4.5.2 Thermal Protection
If the temperature of the main SMPS transformer exceeds 90 °C, the main SMPS
is switched off (safety shut-off ).
4.4.3 Mains Failure Detection
Mains Failure Detection is always operative. When the mains supply is interrupted for about 2 mains cycles, the amplifier will switch off. When the mains voltage
returns to a normal value a soft start occurs.
4.4.4 Fuse Protection
The fuse protection circuit prevents amplifier shut-down (e.g. by a blown mains
fuse or a triggered circuit breaker) during extremely hard use with all channels
working at very high output power. Without intelligent mains current monitoring and control this could easily happen as the rated output power is several
times higher than the capabilities of the standard mains supply.
In order to prevent any shutdown in extreme situations the amplitude of the
input signals will be reduced which will in return also reduce the mains current
draw.
P. 17
USER MANUAL
Q - P O W E R SERIES
4.6 Fans
The fans mounted in your Q-POWER Amplifier operate permanently, but as long
as the temperature remains below 40 °C, they run at their slowest speed and can
hardly be heard. The highest detected temperature from any amplifier channel
controls the speed of the fans. Above 40 °C the speed is increased until it reaches
its maximum value.
Q-POWER
4 OPERATION
SERIES
4.7 Filter Cleaning
The air intake on the front of your Q-POWER Amplifier is fitted with a removable
filter system. If the filter becomes clogged, the unit will not cool as efficiently as
it should and may result in reduced output levels.
WARNING: Turn off the amplifier before removing the front frame.
To clean or replace the filter just slightly unscrew the fixing screw (3) without
completely removing it from the front frame (it is held back by a small plastic spacer on the back side of the frame to avoid loosing the screw). Then shift
the front frame slightly to the right. Then you should be able to remove the
frame from the amplifier completely (pull gently to avoid any bending of the
front frame).
1
2
3
Q-POWER Filter Assembly
1 Foam Filter
2 Front Frame
3 Screw
P. 18
USER MANUAL
Q - P O W E R SERIES
Q-POWER
4 OPERATION
SERIES
4.8 Mounting the Volume Control Security Cover
It is possible to install a solid protection over the volume controls to prevent
intentional or unintentional changes of the amplifier volume settings.
WARNING: Disconnect the amplifier from the mains before installing the
cover.
In the original state the holes needed to fix the security cover on both sides of
the volume knobs are hidden behind the plastic front label. In case you wish to
install the cover please first pierce two holes in the front label to facilitate the
screwing, as shown in the drawings.
To find the exact positions of the holes take the included cardboard template
you will find attached on the last page of this manual and place it on top of
the volume knobs. The positions of the hidden screw holes are indicated on
the template. Then firmly pierce and turn with a pointed tool (we recommend a
Philips PH1 recessed head screwdriver) through the cardboard and the label at
these positions to obtain a clean hole. You now should see the metal of the fine
pitch thread behind the label.
Then remove the cardboard template and fix the cover with the two included
M3 recessed threaded screws.
WARNING: Do not use any pointed tools (e.g. screwdriver) with a diameter of
less than 3,5 mm (0,138 in), as they might be stucked too deeply inside the screw
holes and damage internal components.
P. 19
USER MANUAL
Q - P O W E R SERIES
Q-POWER
5 TROUBLESHOOTING
SERIES
5.1 Problem: No Sound
Indication:
On LEDs not lit
Signal LEDs not lit
Check AC plug.
Confirm that AC outlet works by plugging in another device.
Indication:
On LEDs lit
Signal LEDs not lit
Clip LEDs not lit
Make sure the signal source is operating and eventually try another cable.
Check the position of the volume pots and the position of the gain selec-
tor
Indication:
Signal LEDs responding to signal level
Output Current LEDs are not lit
Check the speaker wiring for breaks.
Try another speaker and cable.
Indication:
P. 20
Signal LEDs show red (Protect Mode)
Overheating will cause protective muting. Check for proper ventilation. If the fans are not running the amplifier requires servicing.
Persistent DC at the outputs will force the amplifier in protect mode and shut down the power supply.
Try to mute or disconnect the signal source and restart the amplifier (i. e. switch off the amplifier, wait until all indicator LEDs extinguish and switch the amplifier on again).
USER MANUAL
Q - P O W E R SERIES
NOTE: For other LED indications than described above or if the problem persists
please unplug the amplifier from the mains supply and refer to your authorised
CAMCO dealer/distributor or repair workshop.
5.2 Problem: Distorted Sound
Indication:
Output Current LEDs are lit
Signal LEDs responding to signal level
Clip LEDs not lit
A faulty speaker or a loose connection could cause this. Check the wiring
and try another speaker.
The signal source might be clipping. Keep the Q-POWER amplifiers volume
pots at least halfway up so that the source does not have to be overdriven.
Keep the Q-POWER amplifiers volume pots at least halfway up and try
changing input sensitivity from 1,4 V to 32 dB or 26 dB with the gain selector on the rear.
Indication:
Output Current LEDs are lit
Signal LEDs responding to signal level
Clip LEDs lit
The amplifier is overdriven by the signal source. Reduce the input signal
level
Q-POWER
5 TROUBLESHOOTING
SERIES
P. 21
5.3 Problem: Hiss / Noise
Unplug the amplifier input to confirm that the hiss is coming from the
source or from a device upstream. Erratic or popping noises indicate an
electronic fault in the offending unit.
To keep the noise floor low, operate the primary signal source at full level
without clipping.
Avoid boosting the signal further between the source and the amplifier.
5.4 Problem: Squeals and Feedback
Microphone feedback should be eliminated with mixer controls. If noise
continues to build up with no microphone gain, there is a serious fault
in the signal processors or cables. Working in succession from the signal
source towards the amplifier and check each device in the signal path by
reducing its gain or by unplugging it.
USER MANUAL
Q - P O W E R SERIES
Q-POWER
6 SPECIFICATIONS
SERIES
Output Power
1 kHz, THD < 1 %, all channels driven
1 kHz, THD < 1 %, one channel driven
Circuitry
Q-POWER 4
Q-POWER 6
Q-POWER 10
290 W @ 16 Ω
520 W @ 8 Ω
800 W @ 4 Ω
800 W @ 2 Ω
470 W @ 16 Ω
800 W @ 8 Ω
1000 W @ 4 Ω
620 W @ 16 Ω
1100 W @ 8 Ω
1800 W @ 4 Ω
1000 W peak @ 4 Ω
1500 W peak @ 4 Ω
950 W @ 70-V line
2500 W peak @ 4 Ω
1600 W @ 70 V line
625 W @ 100 V line
300 W @ 16 Ω
580 W @ 8 Ω
1100 W @ 4 Ω
1000 W @ 2 Ω
480 W @ 16 Ω
960 W @ 8 Ω
1500 W @ 4 Ω
620 W @ 16 Ω
1350 W @ 8 Ω
2400 W @ 4 Ω
1200 W peak @ 4 Ω
1600 W peak @ 4 Ω
2600 W peak @ 4 Ω
Bipolar, Class H 2-step
high efficiency circuit
Bipolar, Class H 2-step
high efficiency circuit
MOSFET, Class D
high efficiency circuit
>110 dB
>113 dB
>112 dB
>115 dB
>112 dB
>115 dB
Signal to Noise-Ratio
20 Hz - 20 kHz, 8 Ω load, unweighted
A-weighted
Frequency Range
8 Ω, 10 dB below rated power, all channels driven
P. 22
USER MANUAL
Q - P O W E R SERIES
20 Hz - 20 kHz ± 0,15 dB
Q-POWER
6 SPECIFICATIONS
SERIES
Q-POWER 4
Q-POWER 6
Q-POWER 10
THD+N (typical)
< 0,02 %
< 0,03 %
< 0,05 %
Damping Factor
>350
> 350
> 600
99 Vp / 198 Vpp
125 Vp / 250 Vpp
145 Vp / 290 Vpp
20 Hz - 10 kHz, 8 Ω,
11 dB below rated power
8 Ω, 1 kHz and below
Maximum output voltage
Input Impedance
15 kΩ balanced
Voltage Gain
Protection Circuits
selectable: 26 dB, 32 dB, or 1,4 V input sensitivity
inrush-current limitation, mains voltage monitoring, temperature monitoring of transformers and heatsinks,
output DC protection, SOA protection, output over current protection,
intelligent mains fuse protection,
Limiter
two individually selectable clip limiters for channels A + B and C + D
Fan
two temperature dependent speed-controlled axial fans
Indicators
LEDs for on, signal/protect, output current and clip
User Interface
four individually adjustable volume control knobs for channel A - D
Input Connectors
Output Connectors
3-pin XLR connector per channel
3-pin Euroblock connector per channel
two four-pole SPEAKON-connectors and barrier-strip-connector terminals for channel A - D
Dimensions (WxHxD)
Net Weight
483 x 88,1 x 421 mm (19”, 2U)
10,6 kg
Shipping Dimensions (WxHxD)
Shipping Weight
10,6 kg
12,6 kg
12,6 kg
We reserve the right to make technical alterations without prior notice.
P. 23
USER MANUAL
Q - P O W E R SERIES
11,5 kg
615 x 135 x 540 mm (0,045 m3)
13,5 kg
Q-POWER
7 TYPICAL PERFORMANCE DIAGRAMS
SERIES
+1
+180
+0.75
+160
+0.5
+140
+0.25
+120
0
+100
T
T
T
+60
-0.5
+40
-0.75
+20
-1.0
deg
0
-1.25
-20
-1.5
-40
-60
-1.75
-80
-2.0
-100
-2.25
-120
-2.5
-100
-2.75
-3.0
T
+80
-0.25
dBr
T
-160
-180
10
20
50
100
200
500
1k
2k
5k
10k
20k
50k
10
20
50
100
200
500
1k
2k
5k
10k
20k
50k
100k
Hz
Hz
Figure 7.1
Gain vs. frequency (Q-POWER 4/Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
Figure 7.3
Phase vs. frequency (Q-POWER 4/Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
-40
-20
-30
-50
-40
-60
-50
dB
dB
-70
-60
-70
-80
-80
-90
-90
-100
-60
-50
-40
-30
-20
-10
0
+10
dBu
Figure 7.2
THD @ 1 kHz, 8 Ω vs. input voltage (Q-POWER 4 /Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
P. 24
USER MANUAL
Q - P O W E R SERIES
-100
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 7.4
THD vs. frequency, 10 dB below clip, 8 Ω (Q-POWER 4/Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
Q-POWER
7 TYPICAL PERFORMANCE DIAGRAMS
SERIES
-20
-30
-30
-40
-40
-50
-50
-60
dBr
dBr
-70
-80
-70
-90
-80
-100
-90
-110
-120
20
50
100
200
500
1k
2k
5k
10k
-100
20k
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Hz
Figure 7.5
Channel separation vs. frequency @ 10 W / 4 Ω (Q-POWER 4/Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
Figure 7.7
Common mode rejection ratio (Q-POWER 4/Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
-20
-30
-30
-40
-40
-50
dB
-50
dB
-60
-70
-80
-80
-90
-90
-100
-100
-60
-50
-40
-30
-20
-10
0
+10
Figure 7.6
DIM intermodulation distortion @ 8 Ω vs. input level
(Q-POWER 4 /Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
USER MANUAL
Q - P O W E R SERIES
-60
-70
dBu
P. 25
-60
-60
-50
-40
-30
-20
-10
0
+10
dBu
Figure 7.8
SMPTE intermodulation distortion (60 Hz and 7 kHz) @ 8 Ω vs. input level
(Q-POWER 4 /Q-POWER 6, Q-POWER 10)
(Measurements of a typical performance)
Q-POWER
7 TYPICAL PERFORMANCE DIAGRAMS
SERIES
1000
2500
1000
1000
2500
800
800
800
2000
600
Watts
Watts
400
300
290
4 Ohm
8 Ohm
Impedance
16 Ohm
Q-POWER 4 Distortion Limited
Output Power (1 % T HD)
Figure 7.9
Q-POWER 4 (Measurements of a typical performance)
1500
1600
1200
900
1000
800
800
480
470
400
Q-POWER 6 Peak Power
0
4 Ohm
8 Ohm
Impedance
16 Ohm
Q-POWER 6 Distortion Limited
Output Power (1% THD)
Figure 7.10
Q-POWER 6 (Measurements of a typical performance)
P. 26
USER MANUAL
Q - P O W E R SERIES
1100
1000
640
620
500
Q-POWER 4 Peak Power
0
2 Ohm
1300
1500
520
200
Watts
1800
580
Q-POWER 10 Peak Power
0
4 Ohm
8 Ohm
Impedance
16 Ohm
Q-POWER 10 Distortion Limited
Output Power (1% THD)
Figure 7.11
Q-POWER 10 (Measurements of a typical performance)
Q-POWER
8 WARRANTY INFORMATION
SERIES
8.1 Summary of Warranty
CAMCO guarantees the Q-POWER Amplifier to be free from defective material
and/or workmanship for a period of six (6) years from the date of sale. When a
defect occurs under normal installation and use, CAMCO will repair the product
under this warranty. In this event, please return the amplifier to your dealer/distributor together with a copy of your sales receipt as proof of purchase.
This warranty provides that examination of the returned product must indicate
in our judgment a manufacturing defect.
8.2 Items Excluded from This Warranty
CAMCO is not liable for any damage caused by shipping accidents, misuse,
abuse, operation with incorrect AC voltage, operation with faulty peripheral
equipment, modification or alteration without prior factory approval, service by
an unauthorised service center and normal wear and tear. Amplifiers on which
the serial number has been removed or defaced are not eligible for warranty
service.
8.3 What CAMCO Will Do
CAMCO (or its appointed agent) undertakes to rectify any defect regardless of
the reason for failure (unless excluded from this warrenty), by repair, replacement or refund as it sees fit.
P. 27
8.4 How to Obtain Warranty Service
You must notify your dealer/distributor of your need for warranty service.
All components must be shipped in the original packaging.
USER MANUAL
Q - P O W E R SERIES
8.5 CAMCO Product Improvement
CAMCO reserves the right to improve the technical standard of its products
without giving prior notice. If in any doubt, please consult your dealer/distri­
butor or contact CAMCO directly for clarification.
Q-POWER
9 SERVICE INFORMATION
SERIES
PLEASE ENCLOSE THIS COMPLETED FORM WITH THE AMPLIFIER
DO NOT SEND SEPARATELY
Owner’s Information
Company Name: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Contact: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Address: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Telephone: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Facsimile: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
eMail Address: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ Model: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Serial Number: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ Purchase Date: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ Expired Warranty
If the warranty has expired, payment will be:
Nature Of Problem
Please describe the conditions that existed when the problem occurred and what
attempts were made to correct it: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Cash/Cheque
VISA
MasterCard
Shipping Address
To transport the amplifier, the original packing materials must be used. Please
return the amplifier to the following address or your nearest CAMCO appointed
distributor.
Other equipment in your system: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
Our web site: www.camcoaudio.com provides a complete list of CAMCO
dealers/distributors.
CAMCO Produktions- und Vertriebs-GmbH für Beschallungs- und Beleuchtungsanlagen, Fischpicke 5, D-57482 Wenden, Germany
P. 28
USER MANUAL
Q - P O W E R SERIES
Q-POWER
10 MAINTENANCE INFORMATION / 11 DECOMMISIONING
SERIES
P. 29
10 Maintenance Information
Cleaning and servicing the inside of the amplifier must never be carried out
by unqualified personnel. The amplifier must never be opened by unqualified
personnel.
Cleaning and servicing work on the inside of the amplifier must only be carried
out by qualified personnel.
Qualified personnel is defined as a person who has gained specialised relevant
knowledge of electronic engineering through education, training and experience and who has sufficient knowledge of all relevant governmental work
safety regulations to be in a position to judge the safe functioning of power
amplifiers based on technical rules according to IEC 60065.
(IEC 60065 (DIN EN 60065) “Safety Requirements for Audio, Video or similar Electronic Appliances”)
In order to guarantee the safe functioning of the amplifier, it has to be checked
regularly depending on its application but at least once a year by a properly
qualified person.
Advice on how to carry out these checks can be found in DIN VDE 0702-1 “Safety
Checks for Electronic Appliances” .
An amplifier that is considered to be unsafe must be labelled accordingly and
stored in a safe place to prevent this amplifier being used mistakenly.
For details on removal and cleaning of the front filter refer to section 4.7.
USER MANUAL
Q - P O W E R SERIES
11 Decommissioning
During the decomissioning process of the amplifier, all legally prescribed rules
and procedures must be adhered to.
Q-POWER
COMPANY INFORMATION
SERIES
Mailing Address:
CAMCO Produktions- und Vertriebs-GmbH
für Beschallungs- und Beleuchtungsanlagen
Fischpicke 5
D-57482 Wenden
Germany
Telephone:
+49 (0) 2762 408-0
Facsimile:
+49 (0) 2762 408-10
Internet:
www.camcoaudio.com
Email:
postmaster@camcoaudio.com
P. 30
USER MANUAL
Q - P O W E R SERIES
Q-POWER
NOTICES
SERIES
P. 31
USER MANUAL
Q - P O W E R SERIES
Q-POWER
JIG
SERIES
bend here
use this template for mounting the poti-cover
pierce the frontlabel carefully as indicated
below to find the tapped holes
pierce label here
holes for potentiometers
P. 32
USER MANUAL
Q - P O W E R SERIES
www.camcoaudio.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising