Catalogue Sheet: EDE Series - Die Cast Aluminum Pictogram Edge-Lit

Catalogue Sheet: EDE Series - Die Cast Aluminum Pictogram Edge-Lit
Project/Location:
Project/Location:
EDE Series
Contractor:
Contractor:
Date:
Die-Cast Aluminum Pictogram
Edge-Lit Sign
Date:
Prepared by:
Prepared by:
Lumacell Model:
Typical specifications
Features
• Self-Powered models provide minimum 120 minutes of
emergency lighting
Supply and install the Emergi-Lite® EDE Series of Die-Cast
pictogram Edge-Lit signs.
• Die-Cast aluminum construction
When specified for surface mount, the unit shall come standard with a
trim plate, trim ring, back box and canopy made of Die-Cast aluminum
with
finish. The trim plate shall have a
profile and allow
for wall- or ceiling-mount installation. The trim ring shall allow for
semi-recessed installation in walls or ceilings with cavity. The canopy
shall allow for wall, end, or ceiling mount.
• Modular design offers great choice of architectural profiles
• Universal Die-Cast back-box for surface or semi-recessed
mounting on ceilings or walls
• LED strip module can be rotated in the unit for either wall or
ceiling mount
• Flat Die-Cast trim plate and galvanized steel back-box for
recessed ceiling mount
• Clear acrylic panel with pictogram legend
• Comes standard with double-face panels for use in single-face
and double-face applications
• White LED light source
• Universal AC input: two-wire 120 to 347VAC; universal DC input:
two-wire 6 to 24VDC
• Energy efficient – consumes less than 2.5W in AC and
DC-remote modes
• Meets or exceeds CSA 22.2 No.141-10
When specified for recessed ceiling-mount, the unit shall come
standard with a flat trim plate of Die-Cast aluminum with
finish, a back box of galvanized steel, and a hardware kit for back box
installation between ceiling joists. The back box shall be provided with
conduit knock-outs at the top, back and end.
All Edge-Lit units shall have the trim plate snap and lock in the
housing with torsion spring retainers, thereby eliminating any visible
screws or hardware. The legend shall be printed on a clear acrylic
panel. The panel shall come standard with double-face legend, for
single-face and double-face applications. The light source shall be
long-life white light-emitting diodes (LED) and shall provide even illumination in normal and emergency operation. The Edge-Lit sign shall
operate with universal 2-wire AC input voltage of 120 to 347VAC at less
than 2.5W and universal 2-wire DC input voltage from 6 to 24VDC at
less than 2.5W. The Edge-Lit sign in a Self-Powered
configuration shall use a sealed Nickel-Cadmium battery of 2.4V
nominal voltage and shall stay illuminated during emergency operation
for at least two hours upon AC failure.
When specified, the Self-Powered unit shall include non-audible
auto-test functions, managed by a micro-controller: it shall execute
automatic tests for 5 minutes every 30 days, 30 minutes every 60 days
and two hours annually. When a fault is detected a red flashing LED
shall identify the failure type: battery, charger circuitry, or LED lamps.
The Edge-Lit sign shall be listed CSA 22.2 No.141-10.
The equipment shall be Emergi-Lite® Model:
.
Power consumption
Model
AC Specs
DC Specs
AC-only
120 to 347VAC
Less than 2.5W
-
-
AC/DC standard
120 to 347VAC
Less than 2.5W
6 to 24VDC
Less than 2.5W
Self-Powered
120 to 347VAC
Less than 3.5W
Nickel-Cadmium battery
Minimum 2 hours
Self-Powered diagnostic
120/347VAC
Less than 3.5W
Nickel-Cadmium battery
Minimum 2 hours
16
Project/Location:
EDE Series
Contractor:
Date:
Die-Cast Aluminum Pictogram
Edge-Lit Sign
Prepared by:
Dimensions
Dimensions are approximate and subject to change.
Angular trim
4” [10.0 cm]
111/2” [29.2 cm]
27/8” [7.4 cm]
113/4” [29.8 cm]
67/8” [17.3 cm]
8” [20.3 cm]
1 ” [2.9 cm]
45/8” [11.6 cm]
21/2” [6.4 cm]
1/8
61/4” [15.7 cm]
45/8” [11.6 cm]
115/8” [29.6 cm]
163/4” [42.7 cm]
16” [40.8 cm]
93/4” [24.7 cm]
3 ” [8.3 cm]
4” [10.0 cm]
21/2” [6.4 cm]
27/8” [7.4 cm]
1/4
13” [32.9 cm]
Circular trim
4” [10.0 cm]
16” [40.8 cm]
111/2” [29.2 cm]
27/8” [7.4 cm]
8” [20.3 cm]
11 ” [29.8 cm]
67/8” [17.3 cm]
61/4” [15.7 cm]
45/8” [11.6 cm]
21/2” [6.4 cm]
3/4
1 ” [2.9 cm]
93/4” [24.7 cm]
4 ” [11.6 cm]
5/8
115/8” [29.6 cm]
163/4” [42.7 cm]
1/8
4” [10.0 cm]
3 ” [8.3 cm]
21/2” [6.4 cm]
27/8” [7.4 cm]
1/4
13” [32.9 cm]
Flat trim
37/8” [9.9 cm]
15” [38.1 cm]
37/8” [9.9 cm]
6” [17.8 cm]
67/8” [17.4 cm]
31/4” [8.3 cm]
13” [32.9 cm]
ordering information
Series
faces/arrow
EDE= die-cast edge-lit
pictogram exit sign
1= one face, no arrows
L= arrow left, single face
R= arrow right, single face
2= two face, no arrows
A= universal two, arrow left or right
Colour
A= brushed
aluminum
B= black
C= chrome
P= polished brass
W= factory white
Z= bronze
Trim
A= angular
C= circular
F= flat
(fully recessed)
VOLTAGE
AC= AC only, 120 to 347VAC
U= 120 to 347VAC, 6 to 24VDC
U48= 120 to 347VAC, 48VDC
UI= Self-Powered, 120 to 347VAC
ID= S
elf-Powered (non-audible), 120/347VAC
ID2= Self-Powered (non-audible), 120/277VAC
NEX= Nexus® system interface**
NEXRF= wireless Nexus® system interface**
**Consult your sales representative for options
available with the Nexus® system
EXAMPLE: EDE2ACU
Unlike EXIT signs, the pictogram sign is not available in double arrow configurations.
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement