Boyles Fitness | Esprit T10 | Owner`s manual | Boyles Fitness Esprit T10 Owner`s manual

Boyles Fitness Esprit T10 Owner`s manual
ESP0038 –Esprit T10
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING
YOUR NEW TREADMILL!
ALWAYS CONSULT A DOCTOR BEFORE STARTING AN EXERCISE PROGRAM
SAFETY HINTS
IMPORTANT: THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY
SAFETY PRECAUTIONS
Thank you for purchasing our product. Even though we go to great efforts to ensure the quality of
each product, occasional errors and/or omissions do occur. In any event should you find this product
to be defective or missing a part please contact our Customer Service Department.
Your treadmill was designed and built for optimum safety. However, certain precautions apply
whenever you use your treadmill. Be sure to read the manual before assembly and operation.
Also, please note the following safety precautions:
DANGER: To reduce the risk of electric shock, always unplug the treadmill from the electrical
outlet immediately after using and before cleaning.
1. Read OWNER OPERATING MANUAL and all accompanying literature and follow it carefully
before using your treadmill.
2. If dizziness, nausea, chest pains, or any other abnormal symptoms are experienced while using
this equipment, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
3. Never leave the treadmill unattended when plugged in. Unplug from the outlet when not in use
and before removing or replacing parts.
4. Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has
been dropped, damaged, or exposed to water.
5. Do not pull the treadmill by the power supply cord or use cord as a handle. Keep cord away from
heated surfaces and open flames.
6. Fitness equipment must always be installed and used on a flat surface. Do not use outdoors or
near water.
7. Do not insert any objects into any openings.
8. Keep children and pets away from this equipment at all times while exercising.
9. Handicapped individuals should have medical approval and close supervision when using this
treadmill.
10.Do not place hands or feet under the treadmill. Always keep hands and legs off of the treadmill
when others are using it.
11.Never turn on treadmill while standing on treadbelt. Always return the treadmill to slow speed to
provide for safe dismount and low speed restart.
a-To disconnect, turn all controls to the off position, then remove plug from outlet.
b-Use the treadmill only for it is intended use as described in this manual.
c-Warm up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward. This
allows your heart rate to gradually increase and decrease and will help prevent straining muscles.
d-Never hold your breath while exercising. Breathing should remain at a normal rate in conjunction
with the level of exercise being performed.
e-Start your program slowly and very gradually increase your speed and distance.
f-Always wear suitable clothing and footwear while exercising. Do not wear loose fitting clothing
that could become entangled with the moving parts of your treadmill.
g-Do not walk or jog barefoot, in stocking feet or loose fitting shoes or slippers.
h-Care must be taken when lifting or moving the equipment, so as not to injure your back. Always
use proper lifting techniques.
WARNING: Before beginning any exercise program consult your physician. This is especially
important for individuals over the age of 35 or persons with pre-existing health problems. Read
all instructions before using any fitness equipment. We assume no responsibility from personal
injury or property damage sustained by or through the use of this product.
CAUTION!! Please be careful when opening this unit.
1
CONGRATULATIONS ON YOUR
NEW TREADMILL AND WELCOME
TO THE SPIRIT FAMILY!
Thank you for your purchase of this quality treadmill. Your new treadmill was manufactured by
one of the leading fitness manufacturers in the world and is backed by one of the most
comprehensive warranties available.
Please take a moment at this time to record the name of the dealer and the date of purchase
below to make any future, needed contact easy. We appreciate your support and we will
always remember that you are the reason that we are in business.
Yours in Health,
BOYLES FITNESS Equipment Pty Ltd.
Name of Dealer______________________________________
Purchase Date ______________________________________
Esprit T10/ ESP0038 _ver. A
2
INTRODUCTION
The treadmill has been designed and constructed to provide trouble free usage and enjoyable exercise.
You can greatly improve your understanding and benefits of exercising by carefully reading the instructions
given in this manual. Please familiarize yourself with the maintenance advice provided for you.
SPECIFICATIONS
•
•
•
•
•
Horsepower Continuous : 2.5 hp
Recommended Speed Range: 1 – 18Km/h
Incline level:Power/0-12 position
Striding Surface: 510 X 1400 mm
Folding Design: Yes
Console
Safety Key
Speed Adjustment Switch
Incline Adjustment Switch
Handrail
Running Belt
Wheel
Main Frame
MAX.USER WEIGHT 150 KGS
3
;
ASSEMBLY PACK CHECK LIST
#74. 3.5 × 12 m/m
Sheet Metal Screw (4pcs)
ASSEMBLY
PACK
CHECK
LIST
#99. 5/16" × 1/2"
Button Head Socket Bolt (14pcs)
#100. 5/16" × 18 × 1.5T
Flat Washer (6pcs)
#101. 5/16" × 23 × 1.5T
Curved Washer (8pcs)
#125. M5 × 25m/m
Phillips Head Screw (2pcs)
#126. M5 × 35m/m
Phillips Head Screw (2pcs)
#44. Safety Key (1pc)
#104. Lubricant (1pc)
#103. M6 (66 × 88)
Allen Wrench (1pc)
#102. Combination M5 Allen Wrench &
Phillips Head Screw Driver (1pc)
4
ASSEMBLY
DRAWING
Step1.
Take out the Treadmill frome the carton and lay it aside on the smooth ground.
Step 2.
Connect the Computer Cable (Lower)(53) with the Right Upright (4).
4
53
Step 3.
Insert the Uprights (L, R)(5,4) into the Frame Base (2) with the 8pcs of 5/16" ×1/2" Button
Head Socket Bolts (99), 4pcs of 5/16" x 18 x 1.5T Flat Washers (100) and 4pcs of 5/16" × 23 ×
1.5T Curved Washers (101) by using the Combination M5 Allen Wrench & Phillips Head
Screw Driver (102).
4
100
99
5
102
99
101
100
99
2
5
101
99
ASSEMBLY
DRAWING
Step 4.
Connecting the Computer Cable (Middle) (55) with the Computer Cable (Lower)(53).
55
53
Step 5.
Install the Console Support (6) into the Uprights (L,R) (5,4) with the 6pcs of 5/16" ×1/2"
Button Head Socket Bolts (99) , 2pcs of 5/16" × 18 × 1.5T Flat Washers (100) and 4pcs
of 5/16" × 23 × 1.5T Curved Washers (101) by using the Combination M5 Allen Wrench
& Phillips Head Screw Driver (102).
6
99
101
100
99
99
101
101
4
100
99
101
99
5
6
99
ASSEMBLY
DRAWING
Step 6.
Install the Outer Handlebar Covers (L & R) (129 & 130) on the Console Support (6) with
the 4pcs of 3.5 × 12 m/m Sheet Metal Screws (74) by using the Combination M5 Allen
Wrench & Phillips Head Screw Driver (102) and tighten them.
6
130
129
74
74
74
7
ASSEMBLY
DRAWING
Step 7.
Connect the Computer Cable (Middle) (55) with the Computer Cable (21-10).
Connect the Connecting Cable (90-7) with the Connecting Cable (21-9).
If there is HR receiver or Speaker, connect 5-Pin HR receiver upper cable (21-11) and 5Pin HR receiver upper cable (90-8).
21-11
21-10
55
90-8
21-9
90-7
Step 8.
1. Insert the Console Assembly (21) into the Console Support (6).
2. Install the Console Assembly (21) and the Console Support (6) with the 2pcs of M5×
25mm Phillips Head Screws (125) and 2pcs of M5×35mm Phillips Head Screws (126)
by using the Combination M5 Allen Wrench & Phillips Head Screw Driver (102) and
tighten them.
21
6
125
126 126
NOTE: Please Tighten All Screw After All Components Assembly Complete.
8
FUNCTIONS
COMPUTER OPERATION INSTRUCTIONS
After turning on and put on the safety key, the console will show up welcome greeting then display
total running mileage, hours, program version and then enter ready mode. When total mileage
accumulates to 100 km total running time to 150 hours, the system will show a lubrication prompt.
After this prompt is shown two times, the message will be deleted automatically.
Displaying Windows
TIME: Accumulated running time from 00:00~99:59 or count-down time from 10~99:00.
SPEED: Showing the running speed of the tread belt from 1KM/h(0.6MPH)~16KM/h(10MPH)
DISTANCE:Accumulated running distance from 0.1~99.99KM.
CALORIES:Showing the fat burnt from 0.1~999.9 calories.
INCLINE:Showing 16 incline levels from 0~15.
PULSE:Showing the heart rate value either wearing heart rate monitor stripe or gripping hand
pulse sensor, the heart rate value is displayed in this window.
LAPS: Displaying track with one circle stands for 0.4KM(1/4M) with value from 0~99.
9
FUNCTIONS
Button Function:
START:Press this button, while running, to start the treadmill after displaying 3, 2, 1, GO.
STOP: Press this button to gradually stop the treadmill and end the workout.
FAST: Press this button to increase workout speed. Press once each time increases
0.1KM/h(0.1MPH). The increment can be adjusted between 0.1 and 1while setting the
treadmill factor.
SLOW: Press this button to decrease workout speed. Press once each time decreases
0.1KM/h(0.1MPH). The increment can be adjusted between 0.1 and 1while setting the
treadmill factor.
UP:
Press this button while running to increase the incline. Press once each time increases one
incline level.
DOWN:Press this button while running to decrease the incline. Press once each time decreases
one incline level.
ENTER:Press this button to enter setting the parameter. While setting, press this button again to
accept and enter next step. Press this button while running to switch the dot matrix
window between speed and incline profiles.
FAN:
This function is optional. Press this button to the fan on/off.
PROGRAM:Press this button to choose training mode. There are four modes: MANUAL,
RANDOM PROGRAM, USER and HRC (Heart Rate Control).
SELECT:While running RANDOM PROGRAM, you can keep on pressing this button to generate
new programs until there is the program you want.
Speedy button for speed:There are five speedy buttons for speed: 2KM/h(MPH), 4 KM/h(MPH).
6 KM/h(MPH), 8 KM/h(MPH) and 10 KM/h(MPH) for speedy setting.
Speedy button for incline:There are five speedy buttons for incline: 2, 4, 6, 8 and 10 for speedy
setting.
Audio Input: This function is optional. It plays the audio signal by the speaker through the internal
amplifier.
SAFETY KEY: Put on this key after turning on the power to function the treadmill. Taking off this
key automatically shuts down the treadmill.
10
FUNCTIONS
Speedy Start (P0MANUAL mode)
Press START button to speedily start the treadmill after turning on the power and putting on the
safety key. Both speed and incline will be at the lowest value. The user has to adjust them to the
desire levels manually.
There are two modes in using the MANUAL mode. One is the speedy start as described above to
use the preset parameters and accumulate the counts. The other is the count-down mode as
procedures below.
A. Use PROGRAM button to choose PO MANUAL then press ENTER to set parameters.
First is setting weigh. Use FAST/SLOW buttons to adjust the weigh and press ENTER for
next setting.
B. Now the AGE will be displayed. Use FAST/SLOW buttons to select the correct value
then press ENTER for next setting.
C. Choose one of count-down factors TIME, DISTANCE, CALORIES and use SELECT to
confirm then press ENTER to set the value. You can press SELECT to return to select the
factor again.
D. Now the selected factor and the value will be displayed. Use FAST/SLOW buttons to
select the proper value and press START to start the treadmill and finish the setting.
E. You can press STOP button to return to the previous step or START to start the treadmill.
RANDOM PROGRAM
This mode which is a profile includes speed and incline automatically generated by the program.
The user can continually choose the profiles until the one which is satisfied. It can also save the
USER mode and make adjustments until a most suitable profile is reached. The operation is as
follows:
A. Use PROGRAM button to select RANDOM PROGRAM mode and press ENTER to profile
selection.
B. Now the dot matrix will display speed profile for 5 seconds then switch to incline profile for
another 5 seconds and recycle. Press ENTER to select the profile and forward to enter next
parameter. Press SELECT button to generate new profile. This step can be continued until
ENTER is pressed.
C. Now the value of the weight is displayed. Use FAST/SLOW buttons to adjust the weight and
press ENTER for next setting.
D. Now the value of the age will be displayed. Use FAST/SLOW buttons to adjust the age and
press ENTER for next setting.
E. Now the preset time 20:00 will be displayed. Use FAST/SLOW buttons to adjust for proper
time duration and press START to start the treadmill.
F. The profile can be saved as an USER profile when the workout is finished. The USER can be
adjusted whenever is necessary.
11
FUNCTIONS
USER mode
This mode provides five personal profiles. Follow the procedures as below.
A. Use PROGRAM to select the USER mode. The program will automatically one without a
profile. If five profiles are saved. The program will ask you if you want to override. Use
UP/DOWM buttons to switch the user names. Use NAME to enter the user name with
FAST/SLOW buttons to enter characters A~Z. There are no more than 7 characters to enter.
Press STOP after entering the last character and exit.
B. Now the value of the weight is displayed. Use FAST/SLOW buttons to adjust the weight and
press ENTER for next setting.
C. Now the value of the age will be displayed. Use FAST/SLOW buttons to adjust the age and
press ENTER for next setting.
D. Now the preset time 30:00 will be displayed. Use FAST/SLOW buttons to adjust for proper
time duration and press ENTER to set profile.
E. Now the dot matrix window will display the SPEED blinking the first row. Use FAST/SLOW
buttons to adjust and press ENTER for next segment. There are 20 segments in a profile. The
segment will blink while setting. After finishing 20 segments, press ENTER to set incline
profile.
F. Now the dot matrix window will display the incline blinking the first row. Use FAST/SLOW
buttons to adjust and press ENTER for next segment. There are 20 segments in a profile. The
segment will blink while setting. After finishing 20 segments, press START to begin the
workout.
HRC (Heart Rate Control mode)
Wearing HR stripe is recommended to use this mode. The transmitter is an optional part. If it is not
installed, the user will grab the hand pulse sensor throughout this mode. The program will ask for
heart rate value when hands are released from the sensor. When there is no heart rate value for a
certain of time, the program stops.
There are two modes for HRC program.
HRC1 adjusts the speed to keep the heart rate at the target value.
HRC2 adjusts the incline to keep the heart rate at the target value.
Operation procedures are as follows
A. Use PROGRAM to select HRC program. Press ENTER button to enter this mode and use
SELECT button to switch between two modes. Press ENTER button to set parameters.
B. Now the value of the weight is displayed. Use FAST/SLOW buttons to adjust the weight and
press ENTER for next setting.
C. Now the preset time 30:00 will be displayed. Use FAST/SLOW buttons to adjust for proper
time duration and press ENTER to set next parameter.
D. Now the value of the age will be displayed. Use FAST/SLOW buttons to adjust the age and
press ENTER for next setting.
E. To change the target heart rate value, the target heart rate value will be in the range of
55%~85% value calculated by the program according to the age you have entered. You can
increase or decrease the target value as what fits you. Consulting your physician to determine
the proper value before setting is recommended. Press START to begin your workout.
Error Message
LOST SPEED: The signal of RPM speed has been lost. Check the imbedded magnet in front
roller and the sensor together with the proper connection of the cable.
12
UNFOLDING
FOLDING
TRANSPORT
¾ UNFOLDING
Pull locking knob and hold running deck and lower down to the floor.
(As shown Figure 1_2.)
¾ FOLDING
Pull the locking knob with right hand, left hand lift the running deck up to 30cm then two hands lift it until
it is locked by the locking knob. (As shown in Figure 3_4)
¾ TRANSPORT
Before moving the treadmill, convert the treadmill to the storage as described above. Make sure that the
Locking Knob is closer fully over the frame guide.
1).
2).
3).
Hold the upper ends of the handrails. Place one foot on the base .
Tilt the treadmill back until it rolls freely on the rear wheels. Carefully move the treadmill to the
desired location. To reduce the risk of injury, use extreme caution while moving the treading. Do
not attempt to move the treadmill over an uneven surface.
Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position.
13
¾
BELT TRACKING ADJUSTMEANT
If during use you notice that walking belt either shifts to the right or the left of center, first
remove "Safety Key" and unplug equipment from AC power source. Using M6 Allen wrench
provided, turn left rear roller adjustment as indicated below clockwise no more the 1/4" of a
turn. Remove M6 Allen wrench, insert "Safety Key" and insert AC power cord into AC
outlet. Turn on your treadmill and observe after running a few minutes to see if problem has
been corrected. This may take several adjustments, so repeat the above procedure.
14
¾
TREADMILL LUBRICATION
Your treadmill should require little maintenance other then periodically applying lubricant.
Lubricating under the treadbelt will ensure superior performance and extend its life expectancy.
HOW TO CHECK TREADBELT FOR PROPER LUBRICATION?
Lift one side of the treadbelt and feel the top surface of the treadboard.
If the surface is slick to the touch, then no further lubrication is required.
If the surface is dry to the touch, apply one packet of lubricant or half of the bottle of lubricant.
HOW TO APPLY LUBRICANT?
1. Lift one side of treadbelt.
2. Pour one half of the lubricant bottle under the center of the treadbelt on the top surface of the
treadboard.
3. Walk on the treadmill at a slow speed for 3 to 5 minutes to evenly distribute lubricant.
NOTE: DO NOT over lubricate treadboard. Any excess lubricant that comes out should be wiped
off.
IMPORTANT: ONLY USE HALF THE BOTTLE OF LUBRICANT PER APPLICATION
LUBRICATION SCHEDULE.
1. After the first 25 hours of use (2-3 months) apply one half bottle of lubricant.
2. Every 50 hours of use (5-8 months) apply one half bottle of lubricant.
15
AEROBIC EXERCISE
Aerobic exercise is any sustained activity that sends oxygen to your muscles via your heart and lungs.
Aerobic exercise improves the fitness of your lungs and heart - your body’s most important muscle.
Aerobic exercise fitness is promoted by any activity that uses your large muscle -arms, legs, or
buttock, for example. Your heart beats quickly and you breathe deeply. An aerobic exercise should
be part of your entire exercise routine.
WEIGHT TRAINING
Along with aerobic exercising which helps get rid of and keep off the excess fat that our bodies can
store, weight training is an essential part of the exercise routine process. Weight training helps tone,
build and strengthen muscle. If you are working above your target zone, you may want to do a less
amount of reps. And as always ,consult your physician before beginning any exercise program.
MUSCLE CHART
CYCLE
The exercise routine that is performed on the cycle will develop the lower body muscle group as well
as condition the circulatory system and provide a good aerobic workout . These muscle groups are
highlighted on the muscle chart below.
16
WARM UP
Quadriceps Stretch
With one hand against a wall for balance, reach behind
you and pull your right foot up. Bring your heel as close
to your buttocks as possible. Hold for 15 counts and
repeat with left foot up.
Inner Thigh Stretch
Sit with the soles of your feet together with your knees
pointing outward. Pull your feet as close into your groin
as possible. Gently push your knees towards the floor.
Hold for 10 counts
Toe Touches
Slowly bend forward from your waist, letting you back
and shoulders relax as you stretch toward your toes.
Reach down as far as you can and hold for 15 counts.
Hamstring Stretches
Sit with your right leg extended. Rest the sole of your
left foot against your right inner thigh. Stretch toward
your toe as far as possible. Hold for 15 counts Relax and
then repeat with left leg extended.
17
OVERVIEW
CHART
18
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16~3
17
18
19
20
21
21~1
21~2
21~3
21~6
21~7
21~9
21~10
21~11
21~12
21~13
21~14
21~15
21~16
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
40
41
DESCRIPTION
Main Frame
Frame Base
Incline Bracket
Right Upright
Left Upright
Console Support
Outer Slide
Inner Slide
Locking Knob
Incline Motor
Drive Belt
Motor Bracket
Motor
Running Belt
Running Deck
Front Roller W/Pulley
Magnet
Rear Roller
Deck Cross Brace
Wheel Sleeve
Rear Wheel Sleeve
Console Assembly
Console Top Cover
Console Bottom Cover
Top Book Rack
Fan
2.5 × 32m/m_Sheet Metal Screw
350m/m_Connecting Cable
350m/m_Computer Cable (Upper)
Amplifier Controller
300m/m_Amplifier Cable
300m/m_Sound Board W/Cable
300m/m_Computer Cable
300m/m_Speaker Cable
200m/m_Ground Wire
Console Locking Tube
Frame Base Cover (L)
Frame Base Cover (R)
Motor Top Cover
Rear Adjustment Base (L )
Rear Adjustment Base (R )
Speed/Hand Pulse Complex
Incline/Hand Pulse Complex
Breaker
On/Off Switch
Frame Base End Cap
Frame Base Front Wheel
Frame Base Rear Wheel
Cushion
Handgrip Foam
Foot Rail
Non-Slip Rubber
Motor Cover Anchor
□21.4 × 21.4m/m_Square End Cap
19
PARTS
LIST
Q'TY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
4
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
2
2
2
6
2
2
2
5
1
NO.
42
43
44
45
46
47
48
49
50
51
52
53
55
56
58
59
60
61
62
63
64
65
66
67
68
69
70
71
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
90~1
90~3
90~5
90~7
90~8
91
92
93
95
DESCRIPTION
□25.4 × 25.4m/m_Square End Cap
□30 × 60m/m_Square End Cap
800m/m_Safety Key
Power Socket
3/8" × 7T_Nut
Sensor Rack
Power Cord
150m/m_Connecting Wire (White)
150m/m_Connecting Wire (Black)
10cm × 764 × 764_Connecting Wire (Black)
Controller
2100m/m_Computer Cable (Lower)
700m/m_Computer Cable (Middle)
1000m/m_Sensor W/Cable
1/2" × 1"_Hex Head Bolt
3/8" × 92m/m_Button Head Socket Bolt
3/8" × 1-3/4"_Hex Head Bolt
3/8" × 1-1/2"_Hex Head Bolt
3/8" × 3/4"_Hex Head Bolt
M8 × 60m/m_Hex Head Bolt
M8 × 12 m/m_Hex Head Bolt
5/16" × 1"_Button Head Socket Bolt
3/8" × 4-1/2"_Socket Head Cap Bolt
3/8" × 2"_Flat Head Socket Bolt
1/2" × 1-1/4"_Carriage Bolt
M8 × 80m/m_Socket Head Cap Bolt
M8 × 25m/m_Flat Head Countersink Bolt
Motor Bottom Cover
5 × 16m/m_Tapping Screw
3.5 × 12 m/m_Sheet Metal Screw
1/2" × 8T_Nyloc Nut
3/8" × 7T_Nyloc Nut
5/16" × 7T_Nyloc Nut
M8 × 8T_Nyloc Nut
3/8" × 2T_Split Washer
M8 × 1.5T_Split Washer
M5_Split Washer
3/8" × 19 × 1.5T_Flat Washer
3/8" × 25 × 2T_Flat Washer
5 × 13 × 1.0T_Flat Washer
Ø50 × Ø13 × 3T_Nylon Washer
Ø10 × Ø25 × 3T_Nylon Washer
Ø6.5 × Ø25 × 1.5T_Concave Washer
M5_Star Washer
5 × 2T_Speed Nut Clip
Beverage Holder Assembly
Beverage Holder
300m/m_Safety Switch Module W/Cable
3 × 10m/m_Sheet Metal Screw
150m/m_Computer Cable
150m/m_Computer Cable
4 × 12m/m_Sheet Metal Screw
Belt Guide
5 × 16m/m_Tapping Screw
Cylinder
20
PARTS
LIST
Q'TY
1
2
1
1
3
1
1
1
1
1
1
1
1
1
2
1
1
2
4
1
2
2
1
4
2
2
6
1
13
28
4
6
2
1
6
2
3
6
4
10
4
3
8
3
2
1
1
1
2
1
1
12
2
30
1
NO.
96
99
100
101
102
103
104
105
106
107
108
109
111
112
113
114
115
116
125
126
128
129
130
131
132
133
134
135
136
137
138
139
140
142
143
144
148
152
155
DESCRIPTION
M8 × 50m/m_Flat Head Countersink Bolt
5/16" × 1/2"_Button Head Socket Bolt
5/16" × 18 × 1.5T_Flat Washer
5/16" × 23 × 1.5T_Curved Washer
Combination M5 Allen Wrench & Phillips Head Screw Driver
M6 (66 × 88)_Allen Wrench
Lubricant
Adjustable Foot Pad
Beverage Holder Cover
500m/m_Speaker W/Cable
Speaker Grill Anchor
3 × 10m/m_Sheet Metal Screw
3.5 × 16m/m_Tapping Screw
Wire Tie Mount
Top Motor Cover Plate
Console Speaker Cover (L)
Console Speaker Cover (R)
3 × 10 m/m_Sheet Metal Screw
M5 × 25m/m_Phillips Head Screw
M5 × 35m/m_Phillips Head Screw
M5 × 12m/m_Phillips Head Screw
Outer Handlebar Cover (L)
Outer Handlebar Cover (R)
Bottom Inner Handlebar Cover (R)
Bottom Inner Handlebar Cover (L)
Top Inner Handlebar Cover (L)
Top Inner Handlebar Cover (R)
3 × 75m/m_Sheet Metal Screw
Handgrip End Cap
Choke
Filter
400m/m_Connecting Cable Of Motor
4 × 19m/m_Sheet Metal Screw
200m/m_Connecting Wire (White)
Receiver, HR
1000m/m_Connecting Cable (Lower)
Copper Foil
Ferrite Core
400m/m_Audio Cable
21
PARTS
LIST
Q'TY
2
14
6
8
1
1
1
2
1
2
6
6
5
5
1
1
1
2
2
2
7
1
1
1
1
1
1
2
2
1
1
1
4
1
1
1
1
1
1
WARRANTY, SAFETY AND ASSEMBLY INFORMATION
ESP0038 - Esprit T10
IMPORTANT
Please read and retain this manual as it will assist with identification for parts and service.
---------------------------------------------------------------------------------------------------------------------------BOYLES FITNESS warrants their treadmill to be free from defects in material and
workmanship under normal use and service conditions.
The various components of the treadmill are warranted against defects and workmanship for
the time periods specified as follows:
ESP0038 –Esprit T10
Lifetime frame
10 years motor
1 year all other parts
All warranty coverage extends only to the original retail purchaser from the date of purchase.
BOYLES FITNESS’ obligation under this Warranty is limited to replacing or repairing, at
BOYLES’ option, the product or parts therein. Any enquiries relating to warranties or spare
parts must be directed to our Freecall 1800 465 070.
For efficient processing of your enquiry please have relevant date of purchase, retailer name
you purchased the item from and the brand on the product. This warranty does not extend to
any damage to a product caused by abuse, improper or abnormal usage (as detailed in this
instruction manual), or repairs not provided by BOYLES. Nor does this warranty extend to
products used for commercial or rental purposes. This warranty does not cover ordinary wear,
tear and weathering, failure to follow directions, improper installation, improper maintenance or
acts of God (such as damage caused by storms, lightning and by snow or ice). No other
Warranty beyond that specifically set forth above is authorised by BOYLES.
Our sales and service centre has been set up to provide assembly assistance, replacement
parts and accessories, and to efficiently handle all warranty related matters.
Freecall
1800 465 070
Hours
9:00am – 4:30pm Mon-Fri (excluding public holidays),
9:00am – 3:00pm Sat
Website
www.bfe.net.au
22
WARRANTY INFORMATION
ESP0038
Congratulations on your purchase!
As of January 1st 2012, new legislation under the Australian Consumer Law requires
certain information to be included in any product warranty issued in Australia. This
warranty compliments the warranty found in the manual and has been developed in line
with the Australian Consumer Law. If the warranty periods offered in the two documents
are different then the greater of the two shall be honoured.
This Esprit T10 is warranted to be free from defects in material and workmanship under
normal use and service conditions for a period of 6 months from the date of purchase of
this article. Evidence of unfair usage or incorrect adjustment by the owner will void this
promise.
The benefits conferred by this manufacturer's warranty are in addition to all rights and
remedies conveyed by the Competition and Consumer Act 2010 (Commonwealth), and
any other statutory rights to which you may already be entitled, and this warranty does
not exclude, restrict or modify any such rights or remedies that are implied by law.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Conditions of Warranty
All warranty coverage extends only to the original retail purchaser from the date of
purchase. Please keep your receipt, tax invoice or other proof of purchase.
This warranty does not extend to any damage to a product caused by abuse, improper or
abnormal usage, or repairs not provided by us or our Service Centre. Nor does this
warranty extend to products used for commercial or rental purposes. This warranty does
not cover ordinary wear, tear and weathering, failure to follow directions, improper
installation, improper maintenance or acts of God (such as damage caused by storms,
lightning, heavy winds and by snow or ice).
Making A Warranty Claim
In order to make a claim under this warranty please direct your enquiries to our Service
Centre. You can contact them on our Freecall 1800 465 070 number or send mail to them
at Action Service Centre: 6 Sedgwick Place, Smeaton Grange, NSW 2567 – if mailing
please include your contact details.
23
A service representative will then assist you in the appropriate action to be taken. For
efficient processing of your enquiry please have proof of purchase, the date of purchase
and the retailer name you purchased the item from, and the brand on the product. Photos
of the product, and scans of receipts, may be requested to assist with your claim.
The service centre representative will assess the claim. If:
1) there is a minor fault, they can offer either a replacement spare part, replacement
unit, repair or other suitable remedy;
2) there is a major fault, they can offer a replacement, repair or suggest you return
to the store you purchased it from for a full refund.
Please note – a request for compensation will need documentary evidence of the
loss or damage suffered. It will also need to be evidenced that such a loss was a
reasonably foreseeable result of a failure by Boyles Fitness to comply with a
consumer guarantee under the Australian Consumer Law.
3) The product was damaged through abnormal use, no refund or repair can be
offered.
The sending of replacements, spare parts or the cost of repair carried out by the Service
Centre will be organized and covered by Boyles Fitness. If collection of the item is
required this will be organized by the Service Centre and at our expense. Do not return
any products without authorization as this will be at your expense.
Our sales and service centre has been set up to provide assembly assistance, replacement
parts and accessories, and to efficiently handle all warranty related matters. Please note
upon receiving your warranty claim our Service Centre will send, via post or email, a
repair and refurbished goods or parts notice.
SERVICE CENTRE
Contact details and hours of operation.
Freecall
1800 465 070
9:00am – 4:30pm Monday to Friday (excluding Public Holidays)
9:00am – 3:00pm Saturday
This product is warranted by Boyles Fitness Equipment Pty Ltd 130 Carrolls Road,
Menangle NSW 2568 Phone 02 4636 6680
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising