Yamaha O1v, V96 Owner's manual

Yamaha O1v, V96 Owner's manual
Owner’s Manual
Keep This Manual For Future Reference.
EN
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning
må kun ske med batteri af samme fabrikat og type. Levér det brugte
batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller
en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty
paristo valmistajan ohjeiden mukaisesti.
(lithium caution)
NEDERLAND / THE NETHERLANDS
• Dit apparaat bevat een lithium batterij voor geheugen back-up.
• This apparatus contains a lithium battery for memory back-up.
• Raadpleeg uw leverancier over de verwijdering van de batterij op het
moment dat u het apparaat ann het einde van de levensduur of
gelieve dan contact op te nemen met de vertegenwoordiging van
Yamaha in uw land.
• For the removal of the battery at the moment of the disposal at the
end of life please consult your retailer or Yamaha representative
office in your country.
• Gooi de batterij niet weg, maar lever hem in als KCA.
• Do not throw away the battery. Instead, hand it in as small chemical
waste.
(lithium disposal)
This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(class B)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif.
90620
Telephone : 714-522-9011
Type of Equipment : Digital Mixing Console
Model Name : 01V96
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(FCC DoC)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in accordance
with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus may not
correspond with the coloured markings identifying the terminals in
your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected
to the terminal in the plug which is marked by the letter E or by the
safety earth symbol
or colored GREEN or GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
(Perchlorate)
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
(3 wires)
• Explanation of Graphical Symbols
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
The above warning is located on the rear
of the unit
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
8
9
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by
the manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms
or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/Power cord
Water warning
• Only use the voltage specified as correct for the device. The required voltage is
printed on the name plate of the device.
• Do not expose the device to rain, use it near water or in damp or wet conditions,
or place containers on it containing liquids which might spill into any openings.
• Use only the specified power code.
• Never insert or remove an electric plug with wet hands.
• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
Do not open
• Do not open the device or attempt to disassemble the internal parts or modify
them in any way. The device contains no user-serviceable parts. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected
by qualified Yamaha service personnel.
If you notice any abnormality
• If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the device, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the device inspected by
qualified Yamaha service personnel.
• If this device should be dropped or damaged, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
• Do not block the vents. This device has ventilation holes at the top/front/rear/
sides to prevent the internal temperature from rising too high. In particular, do
not place the device on its side or upside down, or place it in any poorlyventilated location, such as a bookcase or closet.
Power supply/Power cord
• Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.
• When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Otherwise, the device, TV, or radio may
generate noise.
Location
Connections
• Before moving the device, remove all connected cables.
• When setting up the product, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn off
the power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
• Before connecting the device to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to
minimum.
• Be sure to connect to a properly grounded power source. A ground screw
terminal is provided on the rear panel for safely grounding the device and
preventing electrical shock.
• Avoid setting all equalizer controls and faders to their maximum. Depending on
the condition of the connected devices, doing so may cause feedback and may
damage the speakers.
• Do not expose the device to excessive dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration or damage to the internal components.
• Do not place the device in an unstable position where it might accidentally fall
over.
(5)-1
1/2
Handling caution
Backup battery
• Do not insert your fingers or hand in any gaps or openings on the device (vents,
etc.).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any
gaps or openings on the device (vents, etc.) If this happens, turn off the power
immediately and unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
• This device has a built-in backup battery. When you unplug the power cord from
the AC outlet, the internal data is retained. However, if the backup battery fully
discharges, this data will be lost. If the backup battery is running low, when you
turn on the device the display indicates “WARNING Low Battery!.” In this case,
immediately save the data to an external media using MIDI Bulk Dump, then
have qualified Yamaha service personnel replace the backup battery.
• Do not use headphones for a long period of time at a high or uncomfortable
volume level, since this can cause permanent hearing loss. If you experience
any hearing loss or ringing in the ears, consult a physician.
• Do not apply oil, grease, or contact cleaner to the faders. Doing so may cause
problems with electrical contact or fader motion.
• Do not rest your weight on the device or place heavy objects on it, and avoid use
excessive force on the buttons, switches or connectors.
• This device has a rear-panel slot for installing mini-YGDAI cards. For technical
reasons, certain card combinations are not supported. Before installing any
cards, check the Yamaha web site (see page 6) to see whether your card is
compatible.
Installing cards that are not endorsed by Yamaha may cause electrical shock,
fire, or damage to the unit.
• Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from the unit.
• The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise occurs, relocate the affected equipment.
• When you change the wordclock settings on any device in your digital audio system, some devices may output noise, so turn down your power amps beforehand,
otherwise your speakers may be damaged.
XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
Insert TRS phone jacks are wired as follows: sleeve: ground, tip: send, and ring: return.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
Always turn the power off when the device is not in use.
The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualifi ed Yamaha service
personnel about replacing defective components.
* The illustrations and screen displays as shown in this Owner’s Manual are for instructional purposes only, and may be different from the ones on your device.
* The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective companies.
(5)-1
2/2
6
Yamaha Pro Audio global website
Yamaha Pro Audio global website
http://www.yamahaproaudio.com/
Package Contents
•
•
•
•
•
01V96 Digital Mixing Console
CD-ROM
Power cord
This manual
Studio Manager Installation Guide
Optional Extras
•
•
RK1 Rack Mount Kit
mini YGDAI I/O cards
About this Owner’s Manual
This Owner’s Manual explains how to operate the 01V96 Digital Mixing Console.
The Table of Contents can help you to familiarize yourself with the manual’s organization
and to locate tasks and topics. The index can help you locate specific information.
Before diving in, it’s recommend that you read the “Operating Basics” chapter, starting on
page 27.
Each chapter in this manual discusses a specific section or function of the 01V96. The Input
and Output Channels are explained in the following chapters: “Input Channels,” “Bus
Outs,” and “Aux Outs.” Where possible, these chapters have been organized in order of signal flow, from input to output.
Conventions Used in this Manual
The 01V96 features two types of buttons: physical buttons that you can press (e.g., ENTER
and DISPLAY) and buttons that appear on the display pages. References to physical buttons
are enclosed in square brackets, for example, “press the [ENTER] button.”
References to display page buttons are not emphasized, for example, “move the cursor to the
ON button.”
You can select display pages by using the [DISPLAY] buttons or the Left Tab Scroll, Right
Tab Scroll, and F1–4 buttons below the display. In order to simplify explanations, the procedures reference only the [DISPLAY] button method.
See “Selecting Display Pages” on page 28 for details on all the ways in which you can select
pages.
01V96 Version 2—Owner’s Manual
New Functions in 01V96 Version 2
7
New Functions in 01V96 Version 2
The following functions have been added to the 01V96 as part of the upgrade of the firmware from version 1.0 to version 2.0.
Aux Sends
•
If an Aux Send is set to pre-fader, you can set the Pre point before or after channel mute.
→ page 114
Monitor
•
•
You can select whether the Input Channel’s Pan setting is used when the Input Channel Solo
signal is set to Pre Fader. → page 132
Raising the channel faders for soloed Channels from –∞ can unsolo the Channels.
→ page 132
Surround Pan
•
The on/off status of the Follow Pan button is reflected in the pan and Surround Pan
settings. → page 135
Group/Link
•
•
The Fader Group Master function enables you to control the overall level of the Fader group
channels simultaneously while maintaining the relative level balance of each channel.
→ page 152
The Mute Group Master function enables you to mute all channels in a Mute group
simultaneously. → page 153
Internal Effects
•
You can add optional Add-On Effects to the preset effects. → page 162
Scene Memory
•
•
Any channel or parameter settings in the current scene can be copied and pasted into other
scenes. → page 173
You can select additional parameters for the Recall Safe function. → page 172
Remote Control
•
•
Cubase SX has been added as a target of the Remote layer. → page 189
Yamaha’s proprietary Advanced DAW protocol has been added to Nuendo, Cubase SX, and
General DAW. This enables you to control these devices using the 01V96’s SELECTED
CHANNEL section. (Controllable functions vary depending on the DAW software and version you are using.)
Other Functions
•
•
•
You can set the Routing ST Pair Link so that the routing from paired channels to the Stereo
Bus is linked. → page 232
You can assign the selected channels to a Fader or Mute group using the USER DEFINED
KEYS. → page 247
You can switch the windows of the included Studio Manager software application using the
USER DEFINED KEYS. → page 247
01V96 Version 2—Owner’s Manual
8
Contents
Contents
1
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2
Control Surface & Rear Panel . . . . . . . . . . . . . . . . . . . . . . .
Control Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing an Optional Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
23
26
3
Operating Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting Display Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting Layers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting Fader Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
27
28
29
31
32
33
34
4
Connections and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wordclock Connections and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input and Output Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
37
40
43
5
Tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial Track Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overdubbing to Other Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mixing Recorded Tracks into Stereo (Mixdown) . . . . . . . . . . . . . . . . . . . . . . . . .
47
47
49
60
63
6
Analog I/O & Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Inputs & Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Inputs & Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Converting Sampling Rates of Signals Received at I/O Card Inputs . . . . . . . . . .
Monitoring Digital Input Channel Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dithering Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Transfer Format for Higher Sampling Rates . . . . . . . . . . . . . . . . . . . .
69
69
71
72
73
74
75
7
Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Input Channels from the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Input Channels from the Control Surface . . . . . . . . . . . . . . . . . . . . . .
Pairing Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Naming Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
77
79
90
92
94
8
Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Out 1–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Stereo Out and Bus Out 1–8 from the Display . . . . . . . . . . . . . . . . . .
Setting the Stereo Out and Bus Out 1–8 from the Control Surface . . . . . . . . . . .
Pairing Buses or Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attenuating Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Naming the Stereo Out and Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
97
97
98
99
104
105
106
107
9
Aux Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Aux Out 1–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Setting Aux Out 1–8 from the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Viewing Aux Out Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Setting Aux Out 1–8 from the Control Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
01V96 Version 2—Owner’s Manual
Contents
9
Setting Aux Send Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Viewing Aux Send Settings for Multiple Channels . . . . . . . . . . . . . . . . . . . . . . . . 117
Panning Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Copying Channel Fader Positions to Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . 120
10 Input & Output Patching . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Input Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Output Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Patching Direct Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Insert Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
11 Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Monitor and Solo Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Using the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Using the Solo Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
12 Surround Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
About Surround Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Setting Up and Selecting Surround Pan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Surround Panning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
13 Grouping Channels & Linking Parameters . . . . . . . . . . . . . 149
Grouping & Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Using Fader Groups and Mute Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Using Fader Group Master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Using Mute Group Master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Linking EQ and Compressor Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
14 Internal Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
About the Internal Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Using Effects Processors via Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Inserting the Internal Effects into Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Editing Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
About Add-On Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
About Plug-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
15 Scene Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
About Scene Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
What is Stored in a Scene? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
About Scene Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Storing and Recalling Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Auto Scene Memory Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Fading Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Recalling Scenes Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Sorting Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Copying and Pasting a Scene (Global Paste) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
16 Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
About the Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
General Library Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Using Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
17 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
About Remote Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Pro Tools Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Nuendo/Cubase SX Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Other DAW Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
MIDI Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Machine Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
01V96 Version 2—Owner’s Manual
10
Contents
18 MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
MIDI & the 01V96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
MIDI Port Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Assigning Scenes to Program Changes for Remote Recall . . . . . . . . . . . . . . . . . . 219
Assigning Parameters to Control Changes for Real-time Control . . . . . . . . . . . . 220
Controlling Parameters by Using Parameter Changes . . . . . . . . . . . . . . . . . . . . . 225
Transmitting Parameter Settings via MIDI (Bulk Dump) . . . . . . . . . . . . . . . . . . 226
19 Other Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Changing the Input and Output Channel Names . . . . . . . . . . . . . . . . . . . . . . . . . 229
Setting Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Creating a Custom Layer by Combining Channels (User Assignable Layer) . . . 233
Using the Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Using the User Defined Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Using Operation Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Cascading Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Checking the Battery and the System Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Initializing the 01V96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Calibrating the Faders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Appendix A: Parameter Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
USER DEFINED KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
USER DEFINED KEYS Initial Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
Input Patch Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
Initial Input Patch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Output Patch Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
Initial Output Patch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
User Defined Remote Layer Initial Bank Settings . . . . . . . . . . . . . . . . . . . . . . . . . 256
Effects Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Effects and tempo synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
Preset EQ Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Preset Gate Parameters (fs = 44.1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
Preset Compressor Parameters (fs = 44.1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
Dynamics Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
Appendix B: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
General Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
Analog Input Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Analog Output Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Digital Input Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Digital Output Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
I/O SLOT Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
CONTROL I/O Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Appendix C: MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
Scene Memory to Program Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
Initial Parameter to Control Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Appendix D: Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
MIDI Implementation Chart . . . . . . . . . . . . . . . . . . . . End of Manual
01V96 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . End of Manual
01V96 Level Diagram . . . . . . . . . . . . . . . . . . . . . . . . . End of Manual
01V96 Version 2—Owner’s Manual
Welcome
11
1 Welcome
1
■ Hardware Features
•
•
•
•
•
•
•
•
100-mm motorized faders x 17
Faders can set levels for Input Channels, Aux send levels, and Bus Outs.
Four selectable software layers determine the function of channel faders.
320 x 240 dot LCD display
Buttons and controls in the SELECTED CHANNEL section enable direct editing of
channel EQ parameters.
8 USER-DEFINED KEYS enable you to assign functions to control 01V96 internal
parameters.
ADAT optical connectors
Expansion slot for optional digital I/O, AD, and DA cards.
■ Sonic Specifications
•
•
•
•
•
Linear 24-bit, 128-times oversampling A/D converters
Linear 24-bit, 128-times oversampling D/A converters
20 Hz through 40 kHz frequency response at 96 kHz sampling rate.
106 dB typical dynamic range
32-bit internal signal processing (58-bit accumulator)
■ Inputs and Outputs
•
•
•
•
•
•
•
•
•
•
•
12 mic/line inputs with switchable +48 V phantom power and 4 line inputs
12 analog inserts
Any Bus Outs or Channel Inserts can be routed to four Omni Outs.
Individual outputs for Stereo Out and Monitor Out
Analog 2TR In and Out for use with Tape In and Out signals
An optional card installed in the slot permits a maximum of 16 inputs/outputs.
Digital 2TR In and Out for consumer-format digital audio signals
Double Channel support for recording and playing at 88.2/96 kHz on 44.1/48 kHz legacy multi-track digital recorders.
You can cascade two 01V96s while remaining in the digital domain.
Input patches enable assignment of input signals to desired signal paths.
Output patches enable assignment of Bus Out signals and Input Channel Direct Outs to
desired output jacks.
01V96 Version 2—Owner’s Manual
Welcome
Thank you for choosing the Yamaha 01V96 Digital Mixing Console.
The compact 01V96 Digital Console features 24-bit/96 kHz digital audio processing without compromise, as well as 40-channel simultaneous mixing. The 01V96 covers a broad
range of needs and applications, including multi-track recording, 2-channel mixdown, and
cutting-edge surround sound production. This integrated, comprehensive audio system
features remote control function for DAWs (Digital Audio Workstations) as popularized by
the DM2000 and 02R96 Digital Mixing Consoles.
The 01V96 offers the following features:
12
Chapter 1—Welcome
■ Channel Configuration
•
•
•
•
•
•
32 Input Channels and four ST IN channels can be mixed at a time. Group multiple
channels and pair channels for stereo.
Eight Bus Outs and eight Aux Sends. Bus Outs 1-8 can be routed to Stereo Buses for use
as Group Buses.
Channel library for storing and recalling the channel settings for each Input Channel
and Output Channel
Four-band EQ on each channel
Dynamics processors on all channels (excluding ST IN channels)
Dynamics processor settings and EQ settings can be stored in libraries and recalled.
■ Effects
•
•
•
Four high-quality multi-channel effects (Apply effects via Aux Sends or Channel
Inserts)
Effect library for storing and recalling effect settings.
Optional Add-On Effects packages for adding effects that utilize a variety of new algorithms.
■ Scene Memory
•
Scene memories for storing and recalling mix settings as Scenes
■ Surround Sound
•
•
Supports 3-1, 5.1, and 6.1 channel surround sound production
Surround channel outputs can be assigned to suit connected devices.
■ Remote Control
•
•
•
Control and manage your 01V96 from your Mac or PC using bundled Studio Manager
software.
Remote Layer for remote control of Pro Tools, Nuendo, Cubase SX, and other DAWs
that support the Pro Tools protocol
Control an external recorder via MMC commands.
■ MIDI
•
•
Equipped with MIDI ports and a USB port for computer connection
Scene recall and mix parameter changes via MIDI
01V96 Version 2—Owner’s Manual
Control Surface & Rear Panel
13
2 Control Surface & Rear Panel
2
Control Surface
DISPLAY ACCESS
Section (p. 18)
CH1-4
1
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
CH9-12
PHANTOM +48V
L
A
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
R
B
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
MONITOR
2TR IN
PAD
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
FADER MODE
Section (p. 17)
+4 GAIN -26
-60
-16
GAIN
13
LEVEL
10
+4 GAIN -26
PEAK
14 15
SIGNAL
PEAK
16
SIGNAL
SCENE MEMORY
MIDI
UTILITY
STORE
PAIR/
GROUP
PATCH
EFFECT
VIEW
RECALL
SOLO
SOLO Section
(p. 22)
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
Monitor Out
& Headphones Section (p. 15)
0
-3
PAN
-6
EQ
DYNAMICS
Display Section
(p. 19)
FADER MODE
AUX 1
AUX 2
AUX 3
AUX 4
DEC
INC
-9
-12
-15
EQUALIZER
-18
Data Entry
Section (p. 22)
-24
-30
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
AUX 7
AUX 8
HIGH-MID
FREQUENCY
SELECTED
CHANNEL
Section (p. 20)
HOME (METER)
LOW-MID
LAYER
LAYER Section
(p. 19)
ENTER
1-16
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
5
10
5
15
10
5
15
5
15
15
5
15
5
15
5
15
5
15
5
5
30 15
30 15
30 15
30 15
30 15
30
30
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
30 15
30 15
30 15
30 15
40 20
40 20
40 20
40 20
40 20
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
4
5
6
7
8
9
10
11
5
20
30 15
50 30
60 40
70
50
5
15
40 20
50 30
60 40
70
50
12
15
13
15
14
15
15
ON
ON
ST IN 2
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
ST IN Section
(p. 17)
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
Channel Strip Section (p. 16)
10
15
30 15
50 30
60 40
70
50
10
20
30 15
30
5
20 10
40 20
40 20
10
10
5
0
5
20 10
30 15
30 15
40 20
5
0
0
20 10
15
SEL
SOLO
ST IN 1
20 10
15
20 10
20 10
20 10
20 10
40 20
20 10
3
5
20 10
30 15
2
15
20 10
20
1
5
20 10
15
50
15
20 10
20 10
40
20 10
5
10
5
0
10
ON
SEL
SOLO
5
5
5
0
10
10
10
10
10
10
10
10
10
10
0 +10
0 +10
5
5
0
0
0
0 +10
5
5
5
5
0
0 +10
5
5
5
5
0
0 +10
0 +10
0 +10
5
5
0
0
0
0 +10
5
5
5
5
0
0 +10
5
5
5
5
0
0 +10
0 +10
0 +10
5
0
0
0
5
5
5
5
0 +10
0 +10
0 +10
+10
SEL
STEREO
STEREO Section (p. 16)
USER DEFINED KEYS
Section (p. 21)
Note: Screw holes for attaching a cover are located at both sides of the AD input section of the
01V96. (Size M3, horizontal spacing 417 mm, vertical spacing 36 mm.) You may wish to fabricate your own cover and attach it to the front panel to prevent the controls from being operated inadvertently. Yamaha does not sell such a cover. If you fabricate and attach your own
cover, make sure that the mounting screws do not extend more than 10 mm into the front panel.
You will need to allow approximately 15–20 mm between the top panel and the cover in order
to clear the control knobs and buttons.
01V96 Version 2—Owner’s Manual
Control Surface & Rear Panel
SCENE MEMORY Section (p. 21)
AD Input Section (p. 14)
14
Chapter 2—Control Surface & Rear Panel
AD Input Section
CH1-4
1
2
3
4
5
9
10
11
12
13
15
14
16
1
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
2
INPUT
(BAL)
INSERT
3
4
5
6
7
8
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
PAD
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
13
PEAK
14 15
SIGNAL
PEAK
16
SIGNAL
A INPUT connectors A/B
INPUT A connectors are balanced XLR-3-31-type connectors that accept line-level and
microphone signals. Each of the phantom [+48V] switches on the rear panel turns on or off
the +48V phantom power feed to the corresponding input. INPUT B connectors are balanced TRS phone-type connectors that accept line-level and microphone signals. The nominal signal level of both types of connectors ranges from –60 dB to +4 dB. Phantom power
is not supplied to these connectors.
If you connect cables to INPUT A and INPUT B connectors of the same number, only the
signal from INPUT B is effective.
Tip (hot)
Male XLR plug
1 (ground)
3 (cold)
1/4" TRS phone plug
Ring (cold)
Sleeve (ground)
2 (hot)
B INPUT connectors 13–16
These balanced TRS phone-type connectors accept line-level signals. The nominal signal
level ranges from –26 dB to +4 dB. INPUT 15 & 16 connectors are available only when the
AD 15/16 button is turned off (page 15).
C INSERT I/O connectors
These unbalanced TRS phone-type connectors are used for channel insert ins and outs. Use
a split cable to insert an external effects processor to AD input channels.
1/4" phone plug
Tip (send)
Ring (return)
1/4" phone plug
Sleeve (ground)
To processor’s input
1/4" phone plug
Tip (send)
Sleeve
(ground)
Tip (return)
Connect to INSERT jack
Sleeve (ground)
From processor’s output
01V96 Version 2—Owner’s Manual
Control Surface
15
D PAD switches
These switches turn on or off the 20 dB pad (attenuator) for each AD Input.
E GAIN controls
These controls adjust input sensitivity for each AD Input. Input sensitivity is –16 dB to
–60 dB when the Pad is off, and +4 dB to –40 dB when the Pad is on.
G SIGNAL indicators
These indicators light up when the input signal level exceeds –34 dB.
H AD15/16 selector
This button selects AD Input Channel 15 and 16 signals. When the button is turned on
(pushed in), the 2TR IN signals (page 24) are selected. When the button is turned off
(raised), the INPUT 15 and 16 signals are selected.
Monitor Out & Headphones Section
CH5-8
CH9-12
PHANTOM +48V
L
1
R
IN
5
OUT
2TR
-10dBV (UNBAL)
PHONES
2
MONITOR
2TR IN
4
3
0
LEVEL
10
MONITOR
OUT
0
LEVEL
10
PHONES
A 2TR IN/OUT connectors
These unbalanced RCA phono connectors input and output line-level signals, and are typically used to connect a master recorder.
When the AD15/16 selector in the AD Input section (8) is turned on (pushed in), the signals input at the 2TR IN connectors are routed to AD Input Channels 15 and 16. When the
Monitor Source selector (2) is turned on (pushed in), you can monitor the 2TR IN signals
from the MONITOR OUT connectors.
The 2TR OUT signals are always the same as the STEREO OUT signals.
B Monitor Source selector
This button selects the signals output from the MONITOR OUT connectors on the rear
panel. When this button is turned on (pushed in), you can monitor the signals input from
the 2TR IN connectors. When the button is turned off (raised), you can monitor the Stereo
Out signals or soloed channel signals.
C MONITOR LEVEL control
This control adjusts the monitoring level of the signals output from the MONITOR OUT
connectors.
D PHONES LEVEL control
This control sets the level of the PHONES. (See page 131 for more information on monitoring through the headphones.)
E PHONES jack
You can connect a set of stereo headphones to this stereo phone jack. The signals output
from the MONITOR OUT connectors are also output from this jack.
01V96 Version 2—Owner’s Manual
Control Surface & Rear Panel
F PEAK indicators
These indicators light up when the input signal level is 3 dB below clipping. Adjust the Pad
switch and GAIN control so that the indicator rarely lights up at signal peak.
2
16
Chapter 2—Control Surface & Rear Panel
Channel Strip Section
A [SEL] buttons
These buttons enable you to select desired channels. The [SEL] button indicator for the currently-selected channel lights up. The channel selected by each [SEL] button depends on the
layer selected in the LAYER section (see page 19).
These buttons also allow you to create or cancel channel pairs, and add channels to (or
remove them from) Fader, Mute, EQ, and Compressor groups.
1
SEL
2
SOLO
3
B [SOLO] buttons
These buttons solo the selected channels. The [SOLO] button indicator of the currently-soloed channel lights up.
ON
1
+10
0
5
5
0
10
5
15
10
20
15
30
20
40
30
50
40
60
70
C [ON] buttons
These buttons turn the selected channels on or off. The [ON] button indicators for On
channels light up.
D Channel faders
Depending on the button selected in the FADER MODE section (see page 17), these faders
adjust the selected channel input levels or the Bus Out or Aux Out levels.
50
4
1
17
AUX 1
STEREO Section
1
SEL
A [SEL] button
Selects the Stereo Out.
B [ON] button
Turns the Stereo Out on or off.
2
ON
C [STEREO] fader
This 100mm motorized fader adjusts the final output level of the Stereo Out.
0
5
10
15
20
30
40
50
60
70
3
STEREO
01V96 Version 2—Owner’s Manual
Control Surface
17
ST IN Section
1
ST IN
2
2
SEL
SOLO
SOLO
3
4
ON
ST IN 1
ON
ST IN 2
5
A [ST IN] button
This button selects an ST IN channel pair (ST IN Channels 1 & 2 or 3 & 4) which you can
control using the buttons and controls in the ST IN section. The indicators to the right of
the button indicate the available ST IN channels.
B [SEL] buttons
These buttons select the ST IN channel you want to control.
C [SOLO] buttons
These buttons solo the selected ST IN channels.
D [ON] buttons
These buttons turn the ST IN channels on or off.
E Level controls
These controls adjust the ST IN channel levels.
FADER MODE Section
FADER MODE
1
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
2
HOME (METER)
A [AUX 1]–[AUX 8] buttons
These buttons enable you to select the Aux Send you wish to control. Pressing one of these
buttons switches the Fader mode (see page 33), and displays the corresponding Aux page.
(The selected button’s indicator lights up.)
You can now adjust the send level of signals routed from Input Channels to the corresponding Aux buses by using the faders.
B [HOME] button
This button recalls Meter pages that display Input Channel levels or Output Channel (Bus
Out, Aux Out, Stereo Out) levels (see page 34).
01V96 Version 2—Owner’s Manual
Control Surface & Rear Panel
SEL
18
Chapter 2—Control Surface & Rear Panel
DISPLAY ACCESS Section
1 2 3 4
DISPLAY ACCESS
6
5
SCENE
DIO/SETUP
PAN/
/ INSERT/
ROUTING
DELAY
DYNAMICS
EQ
MIDI
UTILITY
PAIR/
GROUP
PATCH
EFFECT
VIEW
7
8
9 J K L
A [SCENE] button
This button displays a Scene page, enabling you to store and recall Scenes (see page 165).
B [DIO/SETUP] button
This button displays a DIO/Setup page, enabling you to set up the 01V96, including digital
input and output setup and remote control setup (see pgaes 72, 192).
C [MIDI] button
This button displays a MIDI page, enabling you to make MIDI settings (see page 219).
D [UTILITY] button
This button displays a Utility page, enabling you to use the internal oscillators and view
information about installed optional cards.
E [ /INSERT/DELAY] button
This button displays a /INS/DLY page, enabling you to switch the signal phase, set the
signal to be inserted, or set the delay parameters (see pages 79, 127).
F [PAN/ROUTING] button
This button displays a Pan/Route page, enabling you to select a Bus to which the selected
channel signal is routed, adjust the selected channel pan settings, adjust the level of signals
routed from Buses 1–8 to the Stereo Bus, and adjust the stereo or surround pan settings (see
pages 85, 135).
G [PAIR/GROUP] button
This button displays a Pair/Grup page, enabling you to create or cancel channel pairs and
group multiple channel faders or [ON] buttons (see pages 93, 149).
H [PATCH] button
This button displays a Patch page, enabling you to patch input signals and Bus Out signals
to Input channels, or patch signals to the desired output connectors (see page 121).
I [DYNAMICS] button
This button displays a Dynamics page, enabling you to control channel gates and compressors (see page 81).
J [EQ] button
This button displays an EQ page, enabling you to set the equalizer and attenuator of the
selected channel (see page 84).
K [EFFECT] button
This button displays an Effect page, enabling you to edit the internal effects processors and
use optional plug-in cards (see page 161).
L [VIEW] button
This button displays a View page, enabling you to view and set mix parameters for a specific
channel (see page 87).
01V96 Version 2—Owner’s Manual
Control Surface
19
LAYER Section
LAYER
1-16
17-32
2
MASTER REMOTE
2 3
A [1–16]/[17–32] buttons
These buttons select an Input Channel layer as the layer controlled in the Channel Strip section. When the [1–16] button is turned on, you can control Channels 1–16. When the
[17–32] button is turned on, you can control Channels 17–32. (See page 31 for more information on the Input Channel layers.)
B [MASTER] button
This button selects the Master Layer as the layer controlled in the Channel Strip section. You
can use this layer to control Bus Outs and AUX Sends. (See page 31 for more information
on the Master layer.)
C [REMOTE] button
This button selects the Remote Layer as the layer controlled in the Channel Strip section.
You can use this layer to control external MIDI devices or computer-based DAWs. (See
page 189 for more information on the Remote layer.)
Tip: The ST IN section is not affected by the layer settings.
Display Section
OVER
0
-3
-6
-9
-12
-15
1
2
-18
-24
-30
-36
-48
STEREO
3
5
4
6
A Display
This is a 320 x 240 dot LCD display with a backlight.
B Stereo meters
These 12-segment level meters display the final output level of the Stereo Bus.
C Contrast control
This control adjusts the display contrast.
D [F1]–[F4] buttons
These buttons select a page from a multi-page screen. Selecting a tab at the bottom of the
screen using one of these buttons displays the corresponding page. (See page 28 for more
information on displaying a page.)
01V96 Version 2—Owner’s Manual
Control Surface & Rear Panel
1
20
Chapter 2—Control Surface & Rear Panel
E Left Tab Scroll [ ] button
F Right Tab Scroll [ ] button
If there are more pages available than the four whose tabs are currently displayed, use these
buttons to display the additional tabs. These buttons are available only when the left or right
Tab Scroll arrow appears.
Tab Scroll arrow
SELECTED CHANNEL Section
SELECTED CHANNEL
PAN
1
EQUALIZER
6
2
Q
HIGH
3
7
HIGH-MID
4
FREQUENCY
LOW-MID
5
8
GAIN
LOW
A [PAN] control
This control adjusts the pan of the channel selected by the [SEL] button.
B [HIGH] button
C [HIGH-MID] button
D [LOW-MID] button
E [LOW] button
These buttons select the EQ band (HIGH, HIGH-MID, LOW-MID, LOW) of the channel
selected by the [SEL] button. The corresponding button indicator of the currently-selected
band lights up.
F [Q] control
This control adjusts the currently-selected band Q.
G [FREQUENCY] control
This control adjusts the currently-selected band frequency.
H [GAIN] control
This control adjusts the currently-selected band gain.
01V96 Version 2—Owner’s Manual
Control Surface
21
SCENE MEMORY Section
SCENE MEMORY
STORE
2
RECALL
3
2
A [STORE] button
This button enables you to store the current mix settings. (See page 165 for more information on Scene Memories.)
B Scene Up [ ] / Down [ ] buttons
These buttons select a Scene to store or recall. Pressing the Scene Up [ ] button increments
the selection; pressing the Scene Down [ ] button decrements the selection. Holding down
either key increments or decrements the selection continuously.
C [RECALL] button
This button recalls the Scene memory selected by the Scene Up [ ] / Down [ ] buttons.
USER DEFINED KEYS Section
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
1
A [1]–[8] buttons
You can assign any of the 167 functions to these User Defined buttons.
01V96 Version 2—Owner’s Manual
Control Surface & Rear Panel
1
22
Chapter 2—Control Surface & Rear Panel
Data Entry Section
3
DEC
INC
1
4
2
ENTER
A Parameter wheel
This control adjusts the parameter values shown on the display. Turning it clockwise
increases the value; turning it counterclockwise decreases the value. This wheel also enables
you to scroll a displayed list and select a character for entry (see page 30).
B [ENTER] button
This button activates a selected (highlighted) button on the display, and confirms the edited
parameter values.
C [DEC] & [INC] buttons
These buttons increment or decrement a parameter value by one. Pressing the [INC] button increments the value; pressing the [DEC] button decrements the value. Holding down
either key increments or decrements the value continuously.
D Left, Right, Up, Down ([ ]/[ ]/[ ]/[ ]) cursor buttons
These buttons move the cursor around the display pages, or select parameters and options.
Holding down a cursor button moves the cursor continuously in the corresponding direction.
SOLO Section
2
1
SOLO
CLEAR
A [SOLO] indicator
This indicator flashes when single or multiple channels are soloed.
B [CLEAR] button
This button “unsolos” all soloed Channels.
01V96 Version 2—Owner’s Manual
Rear Panel
23
Rear Panel
PHANTOM +48V (p. 23)
Digital I/O Section
(p. 24)
AD Output Section
(p. 23)
MIDI/Control Section
(p. 25)
2
Control Surface & Rear Panel
Power Section (p. 25)
SLOT Section (p. 25)
PHANTOM +48V
3
2
1
A CH1–4 ON/OFF switch
B CH5–8 ON/OFF switch
C CH9–12 ON/OFF switch
Each of these switches turns on or off the +48V phantom power feed to four corresponding
inputs. When the switches are on, +48V phantom power is supplied to the INPUT A connectors.
AD Output Section
1
A MONITOR OUT connectors L/R
These balanced TRS phone-type connectors output monitoring signals or
2TR IN signals. The nominal signal
level is +4 dB.
You can select signals using the Monitor Source selector.
2
3
Tip (hot)
1/4" TRS phone plug
Ring
(cold)
Sleeve (ground)
01V96 Version 2—Owner’s Manual
24
Chapter 2—Control Surface & Rear Panel
B OMNI OUT connectors 1–4
These balanced TRS phone-type connectors output any Bus signals or
channel Direct Out signals. The nominal signal level is +4 dB.
Tip (hot)
1/4" TRS phone plug
Ring
(cold)
Sleeve (ground)
C STEREO OUT connectors L/R
These balanced XLR-3-32-type connectors output the Stereo Out signals.
The nominal signal level is +4 dB.
2 (hot)
3 (cold)
Female XLR plug
1 (ground)
Digital I/O Section
1
2
3
4
5
A WORD CLOCK OUT connector
This BNC connector outputs a wordclock signal from the 01V96 to a connected external
device.
B WORD CLOCK IN connector
This BNC connector inputs a wordclock signal from a connected external device to the
01V96.
C ADAT IN/OUT connectors
These optical TOSLINK connectors input and output ADAT digital audio signals.
D 2TR OUT DIGITAL COAXIAL
This RCA phono connector outputs consumer format (IEC-60958) digital audio. The connector is typically used to connect the digital stereo input (consumer format) of a DAT
recorder, MD recorder, or CD recorder.
E 2TR IN DIGITAL COAXIAL
This RCA phono connector accepts consumer format (IEC-60958) digital audio. The connector is typically used to connect the digital stereo output (consumer format) of a DAT
recorder, MD recorder, or CD recorder.
01V96 Version 2—Owner’s Manual
Rear Panel
25
MIDI/Control Section
2
2
A MIDI IN/THRU/OUT ports
These standard MIDI IN, OUT and THRU ports enable you to connect the 01V96 to other
MIDI equipment.
B TO HOST USB port
This USB port enables you to connect a computer equipped with a USB port.
SLOT Section
1
A SLOT
You can insert optional mini-YGDAI cards into this slot. (See page 26 for information on
installing these cards.)
Power Section
1
2
A POWER ON/OFF switch
This switch turns the power to the 01V96 on or off.
Note: To prevent loud clicks and thumps in your speakers, turn on your audio equipment in
the following order (reverse this order when turning the equipment off)—sound sources, multitrack and master recorders, 01V96, monitoring power amplifiers.
B AC IN connector
This connector enables you to connect the 01V96 to an AC outlet via the supplied power
cord.
01V96 Version 2—Owner’s Manual
Control Surface & Rear Panel
1
26
Chapter 2—Control Surface & Rear Panel
Installing an Optional Card
Visit the following Yamaha Pro Audio web site to ensure that the card you are installing is
supported by the 01V96.
<http://www.yamahaproaudio.com/>.
Follow the steps below to install an optional mini-YGDAI card.
1 Make sure that the power to the 01V96 is turned off.
2 Undo the two fixing screws and remove the slot cover, as shown below.
Keep the cover and fixing screws in a safe place for future use.
3 Insert the card between the guide rails and slide it all the way into the slot,
as shown below.
You may have to push firmly to fully insert the card into the internal connector.
4 Secure the card using the attached thumbscrews.
Tighten the screws firmly to secure the card. Otherwise, the card may not be grounded correctly.
01V96 Version 2—Owner’s Manual
Operating Basics
27
3 Operating Basics
This chapter describes basic operations on the 01V96, including how to use the display and
operate the controls on the top panel.
3
About the Display
3Current Scene
1 Selected
DISPLAY
4EDIT indicator
5MIDI indicator
6Surround mode indicator
7Sampling rate indicator
8 ST IN channel
levels
2 Selected
JChannel name
channel
9Page title
KPage area
LPage tabs
MTab Scroll arrows
A Selected DISPLAY
This section indicates the currently-selected display page group.
B Selected channel
This section indicates the Input or Output Channel currently selected by its corresponding [SEL] button. The first four characters are the Channel ID (e.g., CH1–CH32,
BUS1–BUS8, AUX1–AUX8, ST-L, ST-R). The second four characters are the channel’s
Short name. You can edit the channel’s Short name if you desire (see page 229).
C Current Scene
This section indicates the number and title of the currently-selected Scene memory (see
page 166). If the selected Scene is write-protected, a padlock icon ( ) appears.
D EDIT indicator
This indicator appears when the current mix settings no longer match those of the Scene
that was most-currently recalled.
E MIDI indicator
This indicator appears when the 01V96 is receiving MIDI data via the MIDI IN port,
USB port, or an installed MY8-mLAN card.
F Surround mode indicator
This indicator identifies the currently-selected Surround mode (ST=stereo, 3-1, 5.1, or
6.1) (see page 135).
01V96 Version 2—Owner’s Manual
Operating Basics
The top panel display indicates various parameters that you must set before you can operate
the 01V96. The display indicates the following items:
28
Chapter 3—Operating Basics
G Sampling rate indicator
This indicator identifies the 01V96’s current sampling rate: 44.1 kHz (44k), 48 kHz
(48k), 88.2 kHz (88k), or 96 kHz (96k).
H ST IN channel levels
These level controls indicate the level of ST IN channels 1–4.
I Page title
This section indicates the title of the current page.
J Channel name
On certain pages, this area displays the Long name of the currently-selected channel.
K Page area
This page area displays various page contents.
L Page tabs
These tabs enable you to select a display page.
M Tab Scroll arrows
These arrows indicate that more pages are available.
Selecting Display Pages
To select a display page:
1 Press the corresponding button on the top panel to select the desired page
group.
Display pages are grouped by function. To select a page group, press the desired button in
the DISPLAY ACCESS section.
2 You can select pages that have currently-displayed tabs by pressing the
[F1]–[F4] buttons.
If the selected display page group contains multiple pages, press the [F1]–[F4] buttons
below the corresponding tab to select a specific page.
3 To select a page for which a tab is not currently displayed, press either the
Left or Right [ ]/[ ] Tab Scroll button (depending on where the page is
located) to display the page tab, then press the corresponding [F1]–[F4] button.
If display page groups contain more than four pages, either the left or right arrow appears.
To display the currently-hidden tabs, press the Right or Left [ ]/[ ] Tab Scroll button.
You can also select a page from a page group as follows:
• Selecting the next page in a page group:
Press the button you selected in Step 1 repeatedly. This enables you to select a page that has
a hidden tab.
• To select the previous page in a page group:
Press and hold down the button you selected in Step 1. The screen steps back through the
pages one by one. Release the button when the desired page is displayed. This enables you
to select a page that has a hidden tab.
• To select the first page in the group:
Double-click the button you selected in Step 1.
01V96 Version 2—Owner’s Manual
Display Interface
29
4 Press the cursor buttons to move the cursor (a bold frame) to a button,
parameter box, rotary control, or fader so that you can change the value.
Tip: The 01V96 remembers the current page and parameter when you select a new page group.
If you return to the previous page group, the 01V96 displays the correct page, with the same
parameter selected. You can also select a page by using the controls or buttons on the top panel
(see page 230).
This section describes how to use the display interface.
Rotary Controls & Faders
The rotary controls and faders enable you to adjust the continuously variable parameter values, including Input Channel levels and effects parameters. Press the cursor buttons to move the
cursor to a rotary control or fader you want to adjust, then
rotate the Parameter wheel or press the [INC]/[DEC] buttons
to modify the value.
Buttons
The buttons enable you to turn certain functions on
(enabled) or off (disabled). Move the cursor to the appropriate button, then press the [ENTER] button to turn the function on (highlighted) or off. The buttons also enable you to
select one of two options or to execute certain functions.
Parameter Boxes
The parameter boxes enable you to select one of multiple
options. Press the cursor buttons to move the cursor to a
parameter box, then rotate the Parameter wheel or press the
[INC]/[DEC] buttons to select the setting.
You may need to press the [ENTER] button to confirm a
change in certain parameter boxes. If you edit a value in this
type of parameter box, the value flashes. Press the [ENTER]
button to confirm the change, and the flashing stops. If you
move the cursor to other parameters while the edited value is
flashing, the edit is cancelled.
01V96 Version 2—Owner’s Manual
Operating Basics
Display Interface
3
30
Chapter 3—Operating Basics
Confirmation Messages
For certain functions, the 01V96 prompts you for confirmation before executing the functions, as shown here.
Move the cursor to YES and press [ENTER] to execute the function, or move the cursor to
NO and press [ENTER] to cancel.
If you take no action for awhile, the confirmation window closes automatically and the
function is not executed.
Title Edit Window
The Title Edit window enables you to enter titles for Scene and library memories. You can
enter 4, 12, or 16 characters, depending on the item.
The figure on the left shows uppercase characters and various punctuation marks. The figure on the right shows lowercase characters and numbers.
Use the cursor buttons to select characters, and press the [ENTER] button to enter them
into the title. The cursor moves to the right automatically as each character is entered. Use
the Parameter wheel to move the cursor within the title.
Use the SHIFT LOCK button to select uppercase or lowercase characters, and use the SPC
button to enter a space.
To insert a space at the cursor position and move subsequent characters to the right, move
the cursor to the INS button and press [ENTER].
To delete the character at the cursor position and move subsequent characters to the left,
move the cursor to the DEL button and press [ENTER].
When you have finished, move the cursor to the OK button, then press [ENTER] to confirm
the title. To cancel the title entry, move the cursor to the CANCEL button, then press
[ENTER].
01V96 Version 2—Owner’s Manual
Selecting Layers
31
Selecting Layers
Input Channels and Output Channels (Bus Outs & Aux Outs) are arranged into layers, as
illustrated below. There are four layers altogether.
3
Operating Basics
Input Channel Layer 1–16
Input Channel Layer 17–32
Master Layer
Remote Layer
The currently-selected layer determines the function of
the channel strip, [SEL] buttons, [SOLO] buttons,
[ON] buttons, and faders. Use the LAYER buttons to
select a layer you wish to edit using the channel strip
controls.
LAYER
1-16
17-32
MASTER REMOTE
The following table shows the layers that you can access using the LAYER buttons, and the
parameters you can control using the channel strips on each layer.
LAYER buttons
Layers
Channel Strips
1–8
9–16
[1–16] button
Input Channel Layer 1–16
Input Channels 1–16
[17–32] button
Input Channel Layer 17–32
Input Channels 17–32
[REMOTE] button
Remote Layer
Operation depends on the selected
target (see page 189).
[MASTER] button
Master Layer
Aux Send masters
1–8
Bus Out masters
1–8
Tip:
• The function of each channel strip fader depends on the currently-selected Fader mode (see
page 33).
• The STEREO [SEL] button, [ON] button, and [STEREO] fader always control the Stereo
Out signal, regardless of the Layer settings.
• The ST IN [SEL] buttons, [SOLO] buttons, [ON] buttons, and level control knobs always
adjust the ST IN channels selected via the [ST IN] button regardless of the Layer settings.
01V96 Version 2—Owner’s Manual
32
Chapter 3—Operating Basics
Selecting Channels
To select a channel on the 01V96, press the corresponding [SEL]
button. To adjust the Pan and EQ settings, use the rotary controls
in the SELECTED CHANNEL section. To select a channel on pages
that cover multiple channels, press the corresponding [SEL] button.
1 Press the corresponding LAYER button to select a layer
that includes the desired channel (see page 31).
To select ST IN channels, press the ST IN [ST IN] button.
2 Use the corresponding [SEL] button to select the desired
channel.
The channel is selected and the [SEL] button indicator lights up.
The Channel’s ID and Short name appear in the upper-left corner
of the display. If the currently-displayed page contains a relevant
channel parameter, the cursor moves to that parameter automatically. If the currently-displayed page contains no such parameter, a
page that does contain such a parameter is selected automatically.
SELECTED CHANNEL
PAN
EQUALIZER
Q
HIGH
HIGH-MID
FREQUENCY
LOW-MID
GAIN
LOW
Tip: For paired Input or Output Channels, the channel for which you pressed the [SEL] button
is selected, and its indicator lights up. The [SEL] button indicator of the paired partner flashes.
3 To select the Stereo Out, press the STEREO [SEL] button.
Repeatedly pressing the STEREO [SEL] button toggles between the Stereo Out left and Stereo Out right channels.
If the currently-displayed page contains a relevant Stereo Out parameter, the cursor moves
to that parameter automatically. If the currently-displayed page contains no such parameter, a page that does contain such a parameter is selected automatically.
01V96 Version 2—Owner’s Manual
33
Selecting Fader Modes
Selecting Fader Modes
The function of channel faders (1–16) depends on the selected Layer and Fader mode.
1 Select a layer that includes the desired channel (see page 31).
FADER MODE
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
HOME (METER)
The following table shows the channel fader functions for each Layer and Fader mode.
LAYER buttons
[1–16] button
[17–32] button
[REMOTE] button
[MASTER] button
Fader Mode
Channel Strip Fader
1–8
9–16
[HOME] button
Input Channel 1–16 level
[AUX1]–[AUX8] buttons
Input Channel 1–16 Aux Send level
[HOME] button
Input Channel 17–32 level
[AUX1]–[AUX8] buttons
Input Channel 17–32 Aux Send level
[HOME] button
Operation depends on the selected target (see
page 189).
[AUX1]–[AUX8] buttons
[HOME] button
Aux Send master 1–8
output level
[AUX1]–[AUX8] buttons
No operation
Bus Out master1–8
output level
Note: You cannot select the [AUX1]–[AUX8] buttons while the Master layer is selected. If you
switch to the Master layer while one of the [AUX1]–[AUX8] button indicators is lit, the indicator automatically turns off and the [HOME] button indicator lights up.
01V96 Version 2—Owner’s Manual
3
Operating Basics
2 Press the FADER MODE buttons to select a Fader
mode.
The button indicators identify the following Fader modes:
• When the [HOME] button indicator lights up:
You can use channel faders to control Input Channels
and ST IN Channel levels or Output Channels (Aux
Out 1–8, Bus Out 1–8) master levels.
• When one of the [AUX1]–[AUX8] button indicators
light up:
You can use channel faders to control the corresponding Aux Send level.
34
Chapter 3—Operating Basics
Metering
This section describes how to check Input and Output Channel levels using the Meter
pages.
1 Press the FADER MODE [HOME] button repeatedly until the Meter | Position
page appears.
This page enables you to set the metering position for Input and Output Channels.
1
2
A INPUT section
This section enables you to select the metering position for Input Channel and ST IN
Channel signals.
B OUTPUT section
This section enables you to select the metering position for Output Channel (Aux Out
1–8, Bus Out 1–8, Stereo Out) signals.
2 Move the cursor to the desired parameter button in the INPUT or OUTPUT
section, then press [ENTER].
You can select one of the following three positions in each section.
• PRE EQ.......................... Immediately before EQ.
• PRE FADER .................. Immediately before the fader.
• POST FADER ............... Immediately after the fader.
3 Press the FADER MODE [HOME] button repeatedly until the page listed
below that contains the desired channels appears.
- CH1-32 page
This page displays the Input Channel 1–32 levels respectively.
01V96 Version 2—Owner’s Manual
Metering
35
- ST IN page
This page displays the left and right ST IN Channel 1–4 levels separately.
3
Operating Basics
- Master page
This section displays the Output Channel (Aux Out 1–8, Bus Out 1–8, Stereo Out) levels
altogether.
- Effect page
This page displays the internal effects processor 1–4 input and output levels altogether.
01V96 Version 2—Owner’s Manual
36
Chapter 3—Operating Basics
- Stereo page
This page displays the Stereo Out output level.
If you selected the CH1-32 page or the Master page, use the MASTER MODE parameter to
select one of the following three metering signal types:
• GATE GR....................... The amount of gain reduction for the gate (only for CH1-32)
• COMP GR..................... The amount of gain reduction for the compressor
• LEVEL ........................... Input Channel input level, or Output Channel output level
Tip: These pages also allow you to change the metering position using the POSITION parameter. This parameter setting operates in unison with the Meter | Position page setting.
4 To activate the Peak Hold function, move the cursor to the PEAK HOLD button, then press [ENTER].
The PEAK HOLD button turns on, and the peak level is held on the meters on the page. To
cancel the Peak Hold function, turn the PEAK HOLD button off.
01V96 Version 2—Owner’s Manual
Connections and Setup
37
4 Connections and Setup
This chapter explains how to connect and set up your 01V96.
Connections
The following section explains three typical ways to connect the 01V96 to external equipment, although there are numerous others.
Synthesizer
Connections and Setup
■ Configuring an analog 24-channel mixing system
Synthesizer
MUSIC PRODUCTION SYNTHESIZER
MUSIC PRODUCTION SYNTHESIZER
Integrated Sampling Sequencer
Real-time External Control Surface
Modular Synthesis Plug-in System
Integrated Sampling Sequencer
Real-time External Control Surface
Modular Synthesis Plug-in System
SONG SCENE
SONG SCENE
REC
REC
MY8-AD96
etc.
Effects processor
Master recorder
SLOT
CH1-4
88
1
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
CH9-12
PHANTOM +48V
L
INPUT connector
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
2TR IN connector
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
MONITOR
2TR IN
PAD
OMNI OUT connector
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
13
PEAK
14 15
SIGNAL
LEVEL
10
PHONES
2TR OUT connector
PEAK
16
SIGNAL
SCENE MEMORY
MIDI
UTILITY
STORE
PAIR/
GROUP
PATCH
EFFECT
VIEW
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
0
-3
PAN
-6
EQ
DYNAMICS
DEC
INC
-9
-12
FADER MODE
-15
EQUALIZER
-18
-24
-30
AUX 1
AUX 2
AUX 3
AUX 4
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
AUX 7
AUX 8
HIGH-MID
FREQUENCY
HOME (METER)
MONITOR OUT
connectors
LOW-MID
LAYER
ENTER
1-16
INPUT connector
Guitar
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
+10
INPUT connector
17-32
0 +10
5
0 +10
5
15
15
20 10
10
15
20 10
15
20 10
15
20 10
15
15
20 10
20 10
20 10
15
15
20 10
15
20 10
15
20 10
15
20 10
15
15
20 10
20 10
5
10
15
20 10
20
20
5
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
30
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VOL
ON
VOL
Monitoring system
ST IN 2
0
5
10
15
15
15
40
SOLO
ON
ST IN 1
0
10
5
20 10
SEL
SOLO
ON
0
5
0
10
5
SEL
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
SEL
15
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
PHONES jack
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
4
STEREO
In this system, the 01V96, with an optional AD card (MY8-AD, MY8-AD96, etc.) installed
in the slot, is used as a keyboard mixer or sound re-enforcement mixer. Up to 24 analog
channels, including Inputs 1–16 and slot channels, are available for mixing.
Tip: You can adjust the gain of the AD card channels by setting the DIP switches on the card.
For more information, see your AD card documentation.
01V96 Version 2—Owner’s Manual
38
Chapter 4—Connections and Setup
■ Configuring a recording system with a hard disk recorder
Computer
HDR (Hard Disk Recorder)
MIDI IN
MIDI OUT
SLOT
CH1-4
88
1
2
3
4
5
6
7
8
9
10
11
TO HOST USB port
Effects processor
ADAT IN
MY8-AT
etc.
IN
MIDI OUT
OUT
MIDI IN
IN
ADAT OUT
OUT
WORD CLOCK IN connector
WORD CLOCK OUT
CH5-8
12
13
15
14
16
Master recorder
CH9-12
PHANTOM +48V
L
INPUT connector
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
2TR IN connector
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
MONITOR
2TR IN
PAD
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
OMNI OUT connector
Synthesizer
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
13
PEAK
14 15
SIGNAL
LEVEL
10
2TR OUT connector
SCENE MEMORY
MIDI
UTILITY
PAIR/
GROUP
PATCH
EFFECT
VIEW
STORE
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
PEAK
16
SIGNAL
0
-3
PAN
-6
MUSIC PRODUCTION SYNTHESIZER
Integrated Sampling Sequencer
Real-time External Control Surface
Modular Synthesis Plug-in System
EQ
DYNAMICS
DEC
INC
-9
-12
FADER MODE
-15
EQUALIZER
-18
-24
-30
SONG SCENE
AUX 1
AUX 2
AUX 3
AUX 4
-36
REC
HIGH
Q
-48
STEREO
AUX 5
AUX 6
AUX 7
AUX 8
HIGH-MID
FREQUENCY
HOME (METER)
MONITOR OUT
connectors
LOW-MID
LAYER
ENTER
1-16
INPUT connector
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
+10
INPUT connector
17-32
0 +10
5
0 +10
5
0
15
5
15
15
0 +10
5
15
20 10
15
20 10
15
15
20 10
20 10
20 10
15
15
5
15
20 10
20 10
20 10
15
15
20 10
15
15
20 10
20 10
0
5
10
15
20 10
20
20
5
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
30
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VOL
VOL
Monitoring system
ON
ST IN 2
0
5
10
15
15
40
SOLO
ON
ST IN 1
15
10
5
20 10
SEL
SOLO
ON
0
10
5
SEL
5
5
0
0
10
5
0 +10
5
5
5
0
10
5
0 +10
5
5
5
0
10
5
0 +10
0 +10
5
5
0
10
10
5
0 +10
5
5
0
0
10
5
0 +10
5
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
20 10
20 10
10
0 +10
5
5
0
10
10
5
0 +10
5
5
5
0
SEL
15
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
PHONES jack
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
In this system, the 01V96 is one component in a system that includes a digital MTR, such
as a hard disk recorder, that is connected to the 01V96 via the ADAT IN and OUT connectors on the rear panel and via an optional I/O card (MY8-AT, MY16-AT, MY8-TD, etc.)
installed in the slot. This system will support track recording, overdubbing, track bouncing,
and mixdown. You can also control the hard disk recorder’s transport section by sending
MMC commands from the 01V96 to the recorder.
01V96 Version 2—Owner’s Manual
Connections
39
■ Configuring a recording system that uses a DAW (Digital Audio
Workstation)
Computer
4
Connections and Setup
MIDI interface
MIDI IN
MIDI OUT
Audio interface
SLOT
CH1-4
88
1
2
3
4
5
6
7
8
9
10
11
TO HOST USB port
Effects processor
ADAT IN
MY-16AT
etc.
IN
MIDI OUT
OUT
MIDI IN
IN
ADAT OUT
OUT
WORD CLOCK IN connector
WORD CLOCK OUT
CH5-8
12
13
15
14
16
Master recorder
CH9-12
PHANTOM +48V
L
INPUT connector
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
2TR IN connector
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
CH15/16
2TR IN
INSERT I/O
MONITOR
2TR IN
PAD
20dB
OMNI OUT connector
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
Synthesizer
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-16
-60
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
13
PEAK
14 15
SIGNAL
LEVEL
10
2TR OUT connector
SCENE MEMORY
MIDI
UTILITY
STORE
PAIR/
GROUP
PATCH
EFFECT
VIEW
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
PEAK
16
SIGNAL
0
-3
MUSIC PRODUCTION SYNTHESIZER
Integrated Sampling Sequencer
Real-time External Control Surface
Modular Synthesis Plug-in System
PAN
-6
EQ
DYNAMICS
DEC
INC
-9
-12
FADER MODE
-15
EQUALIZER
-18
-24
SONG SCENE
-30
AUX 1
REC
AUX 2
AUX 3
AUX 4
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
AUX 7
AUX 8
HIGH-MID
FREQUENCY
MONITOR OUT
connectors
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
INPUT connector
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
5
10
5
15
15
20 10
10
15
20 10
15
20 10
15
20 10
15
15
20 10
20 10
20 10
15
5
15
15
20 10
20 10
20 10
15
15
20 10
15
5
15
SEL
0
15
5
5
10
15
20 10
20 10
20 10
20 10
20
20
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VOL
Monitoring system
ON
ST IN 2
0
5
10
15
0
10
5
40 20
50
VOL
SOLO
ON
ST IN 1
20
30
SEL
SOLO
ON
15
40
SEL
5
5
0
10
10
5
0 +10
5
5
0
0
10
5
0 +10
5
5
5
0
10
5
0 +10
5
5
5
0
10
5
0 +10
0 +10
5
5
0
10
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
0
0
0
5
5
5
5
0 +10
0 +10
0 +10
+10
INPUT connector
17-32
15
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
PHONES jack
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
In this system, the 01V96, with an optional I/O card (MY8-AT, MY16-AT, MY8-AE, etc.)
installed in the slot, is connected to a computer-based DAW (Digital Audio Workstation).
The 01V96 can provide audio input and output for the DAW. If you connect the 01V96 and
the computer via USB, the 01V96’s Remote function enables you to control the DAW’s
locate and transport functions and change the parameters.
01V96 Version 2—Owner’s Manual
40
Chapter 4—Connections and Setup
Wordclock Connections and Settings
About Wordclock
Digital audio equipment must be synchronized when digital audio signals are transferred
from one device to another. Even if both devices use identical sampling rates, digital signals
may not transfer correctly, or audible noise or unwanted clicks may occur if the digital
audio processing circuits inside each digital audio device are not synchronized with each
other.
Wordclocks are signals that enable digital audio processing circuits to synchronize with each
other. In a typical digital audio system, one device operates as the wordclock master, transmitting wordclock signals, and the other devices operate as wordclock slaves, synchronizing
to the wordclock master.
If you are digitally connecting the 01V96 to other equipment, you must decide which device
to use as the wordclock master and which devices to use as slaves, then set up all the devices
accordingly. The 01V96 can be used as the wordclock master running at either 44.1 kHz, 48
kHz, 88.2 kHz, or 96 kHz, or slaved to an external wordclock source.
Wordclock Connections
To establish wordclock synchronization between the 01V96 and external devices, you can
distribute wordclock signals independently via dedicated cables, or you can use clock information derived from digital audio connections.
The WORD CLOCK IN and OUT connectors transmit and receive wordclock signals independently on the 01V96. The following examples show two ways in which wordclock signals can be distributed and received via the WORD CLOCK IN and OUT connectors.
• Daisy Chain Distribution
In this example, the wordclock signal is distributed in a “daisy-chain” fashion, with each
device feeding the wordclock signal from the wordclock out connector on to the wordclock
in connector of the next device. This method of distribution is not recommended for larger
systems.
Wordclock
master
WC OUT (BNC)
WC IN
(BNC)
WC OUT
(BNC)
WC IN
(BNC)
Device A
Wordclock slave
WC OUT
(BNC)
Device B
Wordclock slave
WC IN
(BNC)
Device C
Wordclock slave
• Star Distribution
In this example, a dedicated wordclock distribution box is used to supply wordclock signals
from the wordclock master to each wordclock slave individually.
Wordclock
master
01V96 Version 2—Owner’s Manual
WC OUT
(BNC)
Wordclock
distribution box
WC IN (BNC)
WC IN (BNC)
Device A
Wordclock slave
Device B
Wordclock slave
WC IN (BNC)
Device C
Wordclock slave
WC IN (BNC)
Device D
Wordclock slave
Wordclock Connections and Settings
41
If the external devices do not have wordclock in and out connectors, you can use the clock
information included in the digital audio signals. In this case, digital audio signals and
wordclock signals are transferred via the 2TR OUT DIGITAL and 2TR IN DIGITAL jacks
or via the digital I/O card installed in the rear panel slot.
Digital audio signal
+
Wordclock signal
External device
4
Digital I/O
card
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
CH9-12
PHANTOM +48V
L
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
MONITOR
2TR IN
PAD
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
13
PEAK
14 15
SIGNAL
LEVEL
10
SCENE MEMORY
MIDI
UTILITY
PAIR/
GROUP
PATCH
STORE
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
PEAK
16
SIGNAL
0
-3
PAN
-6
EQ
DYNAMICS
EFFECT
DEC
INC
-9
VIEW
-12
FADER MODE
-15
EQUALIZER
-18
-24
-30
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
-36
HIGH
Q
-48
STEREO
HIGH-MID
FREQUENCY
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
1
+10
ON
2
0 +10
5
5
15
15
15
15
15
15
15
15
15
5
0
15
5
15
5
15
5
15
5
15
20 10
5
5
10
10
15
15
20
20
0
15
5
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
30
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ON
ON
ST IN 2
0
15
40
SEL
SOLO
5
5
10
5
20 10
SEL
SOLO
ST IN 1
0
20 10
0
10
5
20 10
ON
16
0 +10
5
0
10
5
ON
15
0 +10
5
0
10
5
20 10
20 10
ON
14
0 +10
5
0
10
10
5
20 10
ON
13
0 +10
5
5
0
10
5
20 10
ON
12
0 +10
5
5
0
10
5
20 10
ON
11
0 +10
5
5
0
10
5
20 10
ON
10
0 +10
5
5
0
10
5
20 10
ON
9
0 +10
5
5
0
10
5
20 10
ON
8
0 +10
5
5
0
10
5
20 10
ON
7
0 +10
5
5
0
10
5
20 10
ON
6
0 +10
5
5
0
10
5
20 10
ON
5
0 +10
5
5
0
10
5
ON
4
0 +10
5
5
0
10
ON
3
0 +10
SEL
15
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
Specifying the Wordclock Source
To digitally connect the 01V96 to external devices, you must specify the wordclock source
for the system. Follow the steps below.
Note: When you change the wordclock settings on any device in your digital audio system,
some devices may output noise due to being out of synchronization. Be sure to turn down your
monitoring device before changing wordclock settings.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Word Clock page appears.
On this page, you can view the current synchronization status of input signals at each slot
and connector.
01V96 Version 2—Owner’s Manual
Connections and Setup
CH1-4
1
A
42
Chapter 4—Connections and Setup
The source select button indicators are explained below:
A usable wordclock signal is present at this input, and it is in sync with the current
01V96 internal clock.
No wordclock signal is present at this input.
A usable wordclock signal is present at this input, but it is out of sync with the current
01V96 internal clock.
This input is the currently-selected wordclock source.
This input was selected as the wordclock source, but no usable signal was received.
Either this input is not receiving wordclock, or else it cannot be used with the currently-installed I/O card.
Tip:
• The FS box displays the sampling frequency at which the 01V96 is currently operating.
• The SLOT TYPE column displays the names of any installed I/O card.
• The IN and OUT columns indicate the number of input and output channels available for
each installed I/O card.
2 Use the cursor buttons to move the cursor to a source, then press [ENTER].
The following are possible wordclock sources:
• SLOT.............................. These buttons select the inputs from the digital I/O card
installed in the slot as the wordclock source. Inputs are selected
in pairs (odd and even numbers in this order). The SLOT TYPE
column displays the names of any installed I/O card. The number of pairs depends on the type of I/O card installed.
• adat ................................ These buttons select the inputs from the ADAT IN connector
on the rear panel. Inputs are selected in pairs (odd and even
numbers in this order).
• WC IN............................ This button selects the wordclock signal input at the WORD
CLOCK IN connector on the rear panel.
• 2TRD ............................. This button selects the 2TR IN DIGITAL input as the wordclock source.
• INT 44.1k, INT 48k
INT 88.2k, INT 96k ..... These buttons select the internal clock generator as the wordclock source. The 01V96 will function as the wordclock master.
Note: To transfer data at higher sampling frequencies (88.2 kHz or 96 kHz) between the
01V96 and connected external devices, you need to set the data transfer format. For more information, see page 72.
Tip: If wordclock transfer is interrupted while the 01V96 (being used as a slave unit) is receiving the clock signal, the unit will automatically switch to an internal clock (INT 44.1k/ INT
48k/INT 88.2k/INT 96k) that is closest to the interrupted clock.
01V96 Version 2—Owner’s Manual
Input and Output Patching
43
Input and Output Patching
The 01V96 is designed to enable you to patch (assign) signals to Inputs and Outputs. This
section explains how to view the signals patched to Inputs and Outputs and change the
assignment.
Tip: If the data from a connected instrument fails to be input, or if you are unable to monitor
the signal at the desired output, check the I/O patching, as explained below:
Patching Input Channels
Follow the steps below to view or change the patching.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the following
page appears.
1
Inputs and Slot channels that are currently assigned to Input Channels are shown in the
parameter boxes (1) beneath the channel numbers. The parameter indicators are
explained below:
• - ......................................No assignment
• AD1–AD16....................INPUT connectors 1–16
• ADAT1–ADAT8............ADAT IN channels 1–8
• SL-01–SL-16..................Slot channels 1–16
• FX1-1–FX1-2 ................Outputs 1–2 of Internal Effects Processor 1
• FX2-1–FX2-2 ................Outputs 1–2 of Internal Effects Processor 2
• FX3-1–FX3-2 ................Outputs 1–2 of Internal Effects Processor 3
• FX4-1–FX4-2 ................Outputs 1–2 of Internal Effects Processor 4
• 2TD-L/R ........................2TR IN DIGITAL L/R connectors
Follow the steps below to view or change the patching.
2 Use the cursor buttons to move the cursor to a patch parameter (1) for
which you want to change the assignment, and rotate the Parameter wheel
or press the [INC]/[DEC] buttons to modify the patching.
01V96 Version 2—Owner’s Manual
4
Connections and Setup
By default, the Input Channels are patched as follows:
• INPUT connectors 1–16 .................... Input Channels 1–16
• ADAT IN channels 1–8....................... Input Channels 17–24
• Slot channels 1–8 ................................ Input Channels 25–32
• Outputs 1–2 of Internal Effects
Processor 1–4 ...................................... ST IN Channels 1–4
44
Chapter 4—Connections and Setup
3 Press [ENTER] to confirm the change.
Tip: To restore the default patching, recall Input Patch memory #00 (see page 178).
Patching Omni Outs
By default, the output connectors are patched as follows:
• OMNI OUT connectors 1–4 ..............Aux Out 1–4
• ADAT OUT channels 1–8 ...................Bus Out 1–8
• Slot channels 1–8.................................Bus Out 1–8
• Slot channels 9–16...............................Bus Out 1–8
• 2TR DIGITAL connectors ..................Stereo Out L & R
Tip:
• The STEREO OUT connectors always output the Stereo Bus signals.
• The MONITOR OUT connectors output monitor signals or the 2TR IN signals, depending
on the Monitor Source selector setting.
Follow the steps below to view or change the patching.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the following
page appears.
1
Signals that are currently assigned to the output connectors are shown in the parameter
boxes (1) underneath the connector numbers. The parameter indicators are explained
below:
• - ..............................................................No assignment
• BUS1–BUS8..........................................Bus Out 1–8 signals
• AUX1–AUX8 ........................................Aux Out 1–8 Signals
• ST L/R....................................................Stereo Out signals
• INS CH1–INS CH32 ...........................Input Channels 1–32 Insert Outs
• INS BUS1–INS BUS8 ..........................Bus Out 1–8 Insert Outs
• INS AUX1–INS AUX8 .........................Aux Out 1–8 Insert Outs
• INS ST-L/ST-R......................................Stereo Out Insert Outs
• CAS BUS1–BUS8 .................................Bus Out 1–8 Cascade Outs
• CAS AUX1–AUX8................................Aux Out 1–8 Cascade Outs
• CAS ST-L/ST-R.....................................Stereo Out Cascade Outs
• CASSOLOL/CASSOLOR....................Solo Channel Cascade Outs
01V96 Version 2—Owner’s Manual
Input and Output Patching
45
2 Use the cursor buttons to move the cursor to a patch parameter (1) you
wish to change, and rotate the Parameter wheel or press the [INC]/[DEC]
buttons to modify the patching.
3 Press [ENTER] to confirm the change.
Tip: To restore the default patching, recall Output Patch memory #00 (see page 179).
4
Connections and Setup
01V96 Version 2—Owner’s Manual
46
Chapter 4—Connections and Setup
01V96 Version 2—Owner’s Manual
Tutorial
47
5 Tutorial
This chapter describes how to use the 01V96 for multitrack recording and mixdown, using
an example in which the 01V96 is connected to a digital multitrack recorder. A rhythm
machine, guitar, bass, and keyboard are recorded.
Connections and Setup
Hard disk recorder
Track
9–16
Track
1–8
OUT
IN
OUT
IN
MY8-AT
Guitar or
bass
SLOT
ADAT OUT
connector
ADAT IN connector
Headphone amplifier
CH1-4
1
INPUT connector
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
CH9-12
PHANTOM +48V
L
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
CH15/16
2TR IN
INSERT I/O
MONITOR
2TR IN
PAD
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
Synthesizer or rhythm machine
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-16
-60
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
13
PEAK
14 15
SIGNAL
LEVEL
10
SCENE MEMORY
MIDI
UTILITY
PAIR/
GROUP
PATCH
STORE
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
PEAK
16
SIGNAL
0
-3
MUSIC PRODUCTION SYNTHESIZER
Integrated Sampling Sequencer
Real-time External Control Surface
Modular Synthesis Plug-in System
PAN
-6
EQ
DYNAMICS
EFFECT
DEC
INC
-9
VIEW
-12
FADER MODE
-15
EQUALIZER
-18
-24
SONG SCENE
-30
REC
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
-36
HIGH
Q
-48
STEREO
HIGH-MID
FREQUENCY
MONITOR OUT
connectors
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
INPUT connector
INPUT connector
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
5
10
5
15
15
15
15
15
15
15
15
5
15
15
15
15
15
5
15
0
5
15
5
5
10
10
15
15
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20
20
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VOL
Monitoring system
ON
ST IN 2
0
0
10
5
20 10
30
VOL
SOLO
ON
ST IN 1
20 10
50
SEL
SOLO
ON
10
40
SEL
5
5
0
10
10
5
0 +10
5
5
0
0
10
5
0 +10
5
5
5
0
10
5
0 +10
5
5
5
0
10
5
0 +10
0 +10
5
5
0
10
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
0
0
0
5
5
5
5
0 +10
0 +10
0 +10
+10
SEL
15
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
PHONES jack
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
Microphone
2 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Word Clock page appears. On this page, specify the wordclock
source.
The best wordclock source depends on the system and environment.
In the following example, a hard disk recorder operating at a sampling frequency of
44.1kHz is used as the wordclock master. The wordclock source is derived from the signal
input at the ADAT IN Channels 1 and 2.
01V96 Version 2—Owner’s Manual
5
Tutorial
1 Connect a digital MTR, musical instruments and a microphone to the 01V96.
In this example, a 16-track hard disk recorder is connected to the ADAT IN and OUT connectors on the rear panel, and the ADAT IN and OUT connectors on an installed MY8-AT
card. (See page 38 for connection details.)
48
Chapter 5—Tutorial
Tip:
• See page 40 for more information on wordclock.
• See page 75 for more information on 01V96s running at higher sampling frequencies
(88.2 kHz or 96 kHz).
Note:
• You can select the 01V96 internal clock as the wordclock source. In this case, you must set
the hard disk recorder so that it will synchronize to an external clock.
• If the 01V96 and a connected device are not synching to each other, the 01V96 displays the
message “Sync Error!” If this happens, check the ADAT IN and OUT connections, digital
I/O card connection, and the sampling frequency setting on each device.
3 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | In
Patch page appears. On this page, make sure that the Input Patch settings
remain set to default values, as shown below.
By default (as shown in this example), the signals input at INPUT connectors 1–16 are
routed to Input Channels 1–16.
The signals input at the ADAT IN connector (the Track 1–8 signals from the hard disk
recorder in this example) are routed to Input Channels 17–24, and the signals input from
the slot (the Track 9–16 signals from the hard disk recorder) are routed to Input Channels
25–32.
If the Input Patch settings have been changed from the default settings, recall Input Patch
memory #00 from the Input Patch library (page 175).
01V96 Version 2—Owner’s Manual
Initial Track Recording
49
4 Press the [PATCH] button repeatedly until the Patch | Out Patch page
appears. On this page, make sure that the Output Patch settings remain set
to default values, as shown below.
5
Tutorial
By default (as shown in this example), the signals output from Bus Outs 1–8 are routed to
the ADAT OUT connector (Tracks 1–8 of the hard disk recorder in this example), and to the
slot output channels (Tracks 9–16 of the hard disk recorder in this example).
If the Output Patch settings have been changed from the default settings, recall Output
Patch memory #00 from the Output Patch library (page 175).
Initial Track Recording
This section explains how to make an initial recording to the hard disk recorder’s tracks of
a rhythm machine, synthesizer, bass, guitar, and microphone that are connected to INPUT
connectors 1–12.
Setting the Input Levels
1 Cue the musicians to play the musical instruments connected to INPUT connectors 1–12
while adjusting the corresponding [PAD]
switches and [GAIN] controls so that the
[PEAK] indicators temporarily flash at the
highest volumes.
[PAD] switch
PAD
20dB
[GAIN] control
-60
-16
GAIN
PEAK
[PEAK] indicator
Tip: The [GAIN] controls adjust the analog input sensitivity. To make a high-quality recording with a wide dynamic range and little noise, set the [GAIN] controls as high as possible
while avoiding clipping.
2 Press the LAYER [1–16] button.
Input Channel Layer 1–16 is now available for control from the channel strip section.
Tip: Since the fader and [ON] button positions of each layer are memorized, those positions
for the corresponding layer are restored when you switch to that layer.
3 Press the FADER MODE [HOME] button, then press the [F1] button to display
the Meter | CH1-32 page.
Meter pages are the start point for mixing and recording. They display channel input and
output levels, and compressor and gate gain reduction amounts.
01V96 Version 2—Owner’s Manual
50
Chapter 5—Tutorial
The CH1-32 page enables you to view Input Channel 1–32 levels and compressor and gate
gain reduction amounts.
2
1
4 Make sure that the LEVEL button (1) is turned on in the METER MODE section.
The METER MODE section enables you to select the type of signals displayed on the
meters. If any button other than the LEVEL button is turned on, move the cursor to the
LEVEL button, then press [ENTER].
5 Move the cursor to the POSITION parameter box (2) to the right of the
LEVEL button, rotate the Parameter wheel or press the [INC]/[DEC] buttons
to select “POST FADER,” then press [ENTER].
The POSITION parameter indicates the metering position. When “POST FADER” is
selected, the meters indicate the post-fader signal levels.
Tip: If you set the POSITION parameter to “PRE EQ,” the pre-EQ input levels are metered.
If you set the parameter to “PRE FADER,” the post-EQ and pre-fader input levels are metered.
6 Make sure that [ON] button indicators 1–12 are lit, then raise faders 1–12 to
0dB.
7 While the musicians play the musical instruments, check the input channel
levels using the level meters on the display.
Tip: If the meters reach the “OVER” level, make sure that the faders are set to 0dB, then lower
the corresponding [GAIN] controls.
Pairing Channels
On the 01V96, you can pair adjacent odd-even channels for stereo operation. Faders and
most mix parameters of paired channels (excluding the Input Patch, phase, routing, and
pan parameters) are linked. Pairing Input Channels is useful when you are connecting stereo sources, such as a rhythm machine or synthesizer.
1 To pair adjacent odd-even Input Channels, press and hold the [SEL] button
for one of the channels you wish to pair, and press the [SEL] button for the
adjacent channel.
The corresponding two channels are paired, and the settings (such as faders, channel on/off,
etc.) of the first channel are copied to the second channel. Subsequently, adjusting the
linked parameters of one of the paired channels will adjust the parameters of its partner in
the same way.
01V96 Version 2—Owner’s Manual
Initial Track Recording
51
Parameters are copied.
SEL
SEL
SEL
SEL
SEL
SEL
2 To cancel a pair, press and hold the [SEL] button for one of the paired channels, and press the [SEL] button for the other channel.
Note: If you want to operate the faders of paired channels, make sure you operate only one
fader for the pair. If you try to operate the faders for both channels in the pair, an excessive
load will be applied to the fader motor, causing malfunction.
Routing Signals
To record the 01V96 input signals to an external digital multitrack recorder, you must specify the destination of the signals for each Input Channel. This process is called “routing.”
There are two routing methods.
• Using Bus Outs 1–8
Input Channel signals are first routed to Buses 1–8, then through Bus Outs 1–8 to the output connectors or channels. Use this method to mix multiple Input Channel signals and
record them to the MTR’s tracks. If you desire, you can process the signals using the Bus Out
1–8 compressors and EQs.
In the following example, Input Channel signals are routed through Bus Outs 1 and 2 to
ADAT OUT connectors 1 and 2.
ADAT OUT
connector
CH 1
INPUT connector 1
Input Channels 1
Bus Out 1
INPUT connector 2
Input Channels 2
Bus Out 2
INPUT connector 3
Input Channels 3
Bus Out 3
INPUT connector 4
Input Channels 4
Bus Out 4
INPUT connector 5
Input Channels 5
Bus Out 5
CH 2
Input
Patch
01V96 Version 2—Owner’s Manual
5
Tutorial
Tip:
• You can still select one of the paired channels for control by pressing the corresponding [SEL]
button. When you select the channel, the [SEL] button indicator lights up, and the [SEL]
button for the paired partner flashes.
• You can also determine how to copy the parameter settings to the paired partner by using a
special window (see page 230).
• You can create or cancel pairs on the Pair/Grup pages (see page 93).
• You can also group the faders, [ON] buttons, EQs, or compressors of multiple channels (see
page 149).
52
Chapter 5—Tutorial
• Using Direct Outs
Each Input Channel signal is directly routed to and output from the specified output connectors and channels. Use this method to patch each Input Channel directly to each MTR
track.
The following example illustrates the signals directly output from ADAT OUT channels
1–5.
ADAT OUT
connector
CH 1
INPUT connector 1
Input Channels 1
INPUT connector 2
Input Channels 2
INPUT connector 3
Input Channels 3
INPUT connector 4
Input Channels 4
INPUT connector 5
Input Channels 5
CH 2
CH 3
CH 4
CH 5
Input
Patch
This section describes how to route signals by combining the above two routing methods.
1 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly to display the
Pan/Route | Rout1-16 page.
This page enables you to select a Bus Out as the signal destination for each channel.
1
2
3
This page contains the following buttons:
A 1–8 buttons
These buttons route Input Channel signals to Buses 1–8. You can select multiple buttons.
B S button
This button routes Input Channel signals to the Stereo Bus.
C D button
This button routes Input Channel signals to the specified output connectors and channels directly.
01V96 Version 2—Owner’s Manual
Initial Track Recording
53
2 Move the cursor to the S button for the Input Channel to
which the musical instrument or microphone is connected,
then press [ENTER] to turn it off.
By default, each Input Channel is routed to the Stereo Bus, which enables
you to monitor the signals from the MONITOR OUT connectors and the
PHONES jack.
However, during multitrack recording you may usually want to monitor
the signals returned from the connected digital MTR, rather than monitoring the Input Channel signals. To do so, you must turn off the S button so that the particular Input Channel signals will not be routed to the Stereo Bus.
4 Press the [PAN/ROUTING] button repeatedly to display the Pan/Route | Pan
page.
This page enables you to set the panpots for signals routed from the Input Channels to the
Stereo Bus, and for signals routed from the Input Channels to the odd-even buses.
5 Move the cursor to the PAN parameter controls for the Input Channels that
are assigned to the odd-even buses, then rotate the Parameter wheel or
press the [INC]/[DEC] buttons to set the pan.
Cursor on the
PAN parameter
control
Tip: You can also use the [SEL] buttons to select Input Channels, and the SELECTED CHANNEL [PAN] control to adjust the pan setting.
6 To route Input Channel signals to Direct Outs, press the DISPLAY ACCESS
[PATCH] button repeatedly until the Patch | Direct Out page appears.
The Direct Out page enables you to specify the output connectors or channels to which each
Input Channel is directly patched.
7 Move the cursor to the parameter box for the Input Channels you want to
route to Direct Outs, then specify the output connectors or channels.
01V96 Version 2—Owner’s Manual
5
Tutorial
3 To route Input Channel signals to the connected digital MTR via Buses 1–8,
use the 1–8 buttons to specify a Bus Out as the destination for each of the
Input Channels to which the musical instruments and microphone are connected.
In this example, Input Channels 1–4 are assigned to Buses 1 and 2, and Input Channels
5–8 are assigned to Buses 3 and 4.
54
Chapter 5—Tutorial
In this example, Input Channel 9–12 signals are routed to ADAT OUT channels 5–8.
8 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
Pan/Route | Rout1-16 page appears.
9 Move the cursor to the D button for the Input Channels you want to route
to Direct Outs, then press [ENTER].
The Input Channels for which the D buttons are turned on
are directly patched to the output connectors or channels
specified in Step 7.
Adjusting the Monitoring Level
You can monitor the recording signals by placing the digital MTR in record ready mode,
routing the signals sent to Tracks 1–8 of the digital MTR back to the 01V96’s Input Channels
17–24, then patching them to the MONITOR OUT connectors and the PHONES jack.
1 Arm the connected digital MTR’s tracks for recording.
At this time, set the monitor mode on the digital MTR accordingly so that you can monitor
the input signals on the armed tracks. (Refer to the owner’s manual for the digital MTR for
more information.) In this way, signals sent to Tracks 1–8 of the digital MTR are returned
to the 01V96’s Input Channels 17–24.
2 Press the LAYER [17–32] button.
Input Channel Layer 17–32 is now available for control from the channel strip section.
3 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
Pan/Route | Rout17-STI page appears.
01V96 Version 2—Owner’s Manual
Initial Track Recording
55
5
Tip: Controlling Input Channel 17–32 Pan settings, faders, and the [ON] buttons will affect
the monitoring signal, but will not affect the signal recorded to the digital MTR.
5 Press the DISPLAY ACCESS [HOME] button, then press the [F1] button to display the Meter | CH1-32 page.
6 Make sure that [ON] button indicators 1–8 are steadily lit, then raise the [STEREO] fader to 0 dB.
7 While the musicians play the musical instruments, adjust faders 1–8, [MONITOR OUT] control, and [PHONES] control to set the appropriate monitoring
level.
Now you can monitor via the monitoring system and headphones the signals sent from
Input Channels 17–24 to the Stereo Bus.
Note: If the L & R level meters reach the “OVER” position, lower the [STEREO] fader.
01V96 Version 2—Owner’s Manual
Tutorial
4 Make sure that the S buttons for Input Channels 17–24 are turned on and
the 1–8 buttons are turned off, then use the PAN control to pan the monitoring signal.
56
Chapter 5—Tutorial
EQ’ing the Input Signals
The 01V96’s Input Channels feature 4-band full parametric EQ. This section describes how
to apply EQ to the signals before they are recorded to the tracks.
1 Press the LAYER [1–16] button.
Input Channel Layer 1–16 is now available for control from the channel strip section.
2 Press the [SEL] button for the Input Channel to which you want to apply EQ.
3 Press the [EQ] button, then the [F1] button to display the EQ | EQ Edit page.
The EQ Edit page enables you to adjust the EQ parameters for the currently-selected channel.
4 Make sure that the EQ ON button (in the upper-left corner) is turned ON.
The EQ ON/OFF button turns the currently-selected Input Channel’s EQ on or off. If the
button is off, press the [ENTER] button to turn it on.
5 While a musician plays the musical instrument, adjust the EQ parameters.
To do so, move the cursor to the parameters in the lower half of the page, then rotate the
Parameter wheel to change the values. You can adjust the following parameters for the
LOW, L-MID, H-MID, and HIGH bands individually.
01V96 Version 2—Owner’s Manual
57
Initial Track Recording
• Q
This parameter control specifies the Q (slope) for cut/boost of the center frequency set via
the F parameter control. The setting range is between 10 and 0.10. The higher the value, the
steeper the slope becomes. This parameter control also selects the type of EQ for the LOW
and HIGH band.
• F (Frequency)
This parameter control specifies the center frequency for cut/boost, with a setting range of
21.2 Hz to 20.0 kHz.
• G (Gain)
This parameter control specifies the cut/boost amount in the range of –18.0 dB to +18.0 dB.
The LOW and HIGH GAIN controls function as filter on/off controls when Q is set to HPF
and LPF respectively.
Tip:
• Turn the Q parameter control for the LOW band clockwise all the
way to set the LOW-band EQ to “L. SHELF” (low-shelving), and
counter-clockwise all the way to set it to “HPF” (high-pass filter).
• Turn the Q parameter control for the HIGH band clockwise all
the way to set the HIGH-band EQ to “H. SHELF” (high-shelving), and counter-clockwise all the way to set it to “LPF” (low-pass
filter).
• By default, the LOW band is set to “L. SHELF,” and the HIGH
band is set to “H. SHELF.”
SELECTED CHANNEL
PAN
EQUALIZER
Q
HIGH
HIGH-MID
FREQUENCY
LOW-MID
GAIN
LOW
6 In the same way, adjust the EQ for the other channels.
Tip:
• The meters in the upper-right corner of the page indicate the post-EQ signal levels of the
currently-selected Input Channel. If these meters reach the “OVER” position, lower the
pre-EQ signal level using the ATT. parameter control located in the upper-left on the page.
• You can also apply EQ to the Input Channel signals returned from the recorder. In this way,
you can process only the monitoring signals, without affecting the signals being recorded to
the recorder.
• You can use the EQ settings (programs) in the provided EQ library for various applications
and instruments.
Compressing the Input Signals
The 01V96’s Input Channels 1–32 feature individual channel compressors. This section
describes how to compress the signals before they are recorded to the tracks.
1 Press the LAYER [1–16] button.
Input Channel Layer 1–16 is now available for control from the channel strip section.
2 Press the [SEL] button of the Input Channel to which you want to apply compression.
01V96 Version 2—Owner’s Manual
Tutorial
You can also press the buttons ([HIGH], [HIGH-MID],
[LOW-MID], [LOW]) in the SELECTED CHANNEL section to
select the desired band and use the rotary controls ([Q], [FREQUENCY], [GAIN]) to directly edit the Q, F, and G parameters.
5
58
Chapter 5—Tutorial
3 Press the [DYNAMICS] button, then press the [F4] button.
The Dynamics | Comp Lib page appears. This page enables you to store compressor settings
(programs) to the Compressor library, and recall compressor programs from the library.
This example uses one of the compressor programs 1–36 from the Compressor library.
4 Rotate the Parameter wheel to scroll the library title list, and select a program that you want to recall.
The selected program appears inside
the dotted box.
5 Move the cursor to the RECALL button located to the left of the library title
list, then press [ENTER].
The selected program is recalled.
6 Press the [F3] button.
The 01V96 displays the Dynamics | Comp Edit page, which enables you to adjust compressor parameters.
01V96 Version 2—Owner’s Manual
Initial Track Recording
59
5
7 Press the [ENTER] button to turn on the ON/OFF button located in the
lower-left corner of the page.
The ON/OFF button turns the currently-selected Input Channel’s compressor on or off.
8 While a musician plays the musical instrument, adjust the compressor
parameters.
To do so, move the cursor to the desired parameter in the PARAMETER section on the page,
then rotate the Parameter wheel or press the [INC]/[DEC] buttons.
Input Channels 1–32 feature a gate that can be used independently of the compressor. To
use the gate, first press the [DYNAMICS] button, then the [F2] button to access the Gate
library. After you recall a gate program, press the [Dynamics] button, then the [F1] button
to display the Gate Edit page, which enables you to adjust gate parameters.
Recording
When you finish setting up each channel, you can start recording on the digital MTR as follows:
1 Start recording on the digital MTR, and cue the musicians to start playing
the musical instruments.
During recording, press the [HOME] button to display the Meter | CH1-32 page or the
Master page, and check to confirm that the Input Channel levels and Bus 1–8 output levels
are not clipping.
2 When you finish playing, stop the digital MTR.
3 To check the recording, play the digital MTR from the beginning.
4 If you are satisfied with the recording, stop the playback and disarm Tracks
1–8 on the recorder.
Tip: If the digital MTR supports MMC (MIDI Machine Control) commands, you can use
the 01V96’s Machine Control function to select tracks or locate a position on the recorder from
the 01V96 (see page 212).
01V96 Version 2—Owner’s Manual
Tutorial
Tip:
• The 01V96 features four types of dynamics processors: COMP (Compressor), EXPAND
(Expander), COMP. (S) (Compander Soft), and COMP. (H) (Compander Hard). These
processors feature different parameters. (See page 272 for the parameters for each compressor type.)
• You cannot change the compressor type on the Comp Edit page. To change the compressor
type, recall a program that uses the desired compressor type from the Compressor library,
then adjust the parameters as desired.
60
Chapter 5—Tutorial
Overdubbing to Other Tracks
This section describes how to overdub the musical instruments or microphone connected
to the INPUT connectors 1 and 2 to the digital MTR’s Tracks 9 and 10, while listening to the
performance recorded on Tracks 1–8.
Setting the Input Levels
1 Connect the musical instruments to INPUT
connectors 1 and 2, and adjust the corresponding [PAD] switches and [GAIN] controls so that the [PEAK] indicators
temporarily flash at the highest volumes.
[PAD] switch
PAD
20dB
[GAIN] control
-60
-16
GAIN
PEAK
[PEAK] indicator
2 Press the LAYER [1–16] button.
Input Channel Layer 1–16 is now available for control from the channel strip section.
3 Press the DISPLAY ACCESS [HOME] button, then press the [F1] button to display the Meter | CH1-32 page.
4 Make sure that [ON] button indicators for the channels to which the instruments or microphone are connected are lit, then raise the corresponding
faders to 0dB.
Turn off the [ON] buttons for the channels not in use.
5 While the musicians play the musical instruments, check the input channel
levels using the level meters on the display.
01V96 Version 2—Owner’s Manual
Overdubbing to Other Tracks
61
Routing Signals
Follow the steps below to route the Input Channel 1 and 2 signals to Slot Channels 1 and 2
directly so that the signals will be recorded to Tracks 9 and 10 on the digital MTR.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | Direct
Out page appears.
2 Move the cursor to the parameter box for the Input Channels you want to
route to Direct Outs, then specify the output connectors or channels.
In this example, Input Channel 1 and 2 signals are patched to Slot output channels 1 and 2.
5
Tutorial
3 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
Pan/Route | Rout1-16 page appears.
4 Move the cursor to the D buttons for Input Channels 1 and 2,
then press [ENTER]. Turn off the S buttons and 1–8 buttons.
The Input Channel 1 and 2 signals are now routed to Slot output channels
1 and 2, then output to Tracks 9 and 10 on the digital MTR.
Adjusting the Monitoring Level
Follow the steps below to place the digital MTR in record ready mode and monitor the signals (that are sent from Tracks 9 and 10 of the digital MTR back to the 01V96’s Input Channels 25 and 26) through the MONITOR OUT connectors and the PHONES jack.
1 Arm the connected digital MTR’s Tracks 9 and 10.
At this time, set the monitor mode on the digital MTR accordingly so that you can monitor
the input signals on the armed tracks, and monitor playback signals from the other tracks.
(Refer to the owner’s manual for the digital MTR for more information.)
2 Press the LAYER [17–32] button.
Input Channel Layer 17–32 is now available for control from the channel strip section.
3 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
Pan/Route | Rout17–STI page appears.
4 Make sure that the S buttons for Input Channels 25 and 26 are turned on
and the 1–8 buttons are turned off.
01V96 Version 2—Owner’s Manual
62
Chapter 5—Tutorial
5 Press the [F1] button to display the Pan/Route | Pan page, then use the PAN
parameter controls on the page to pan channel signals.
6 Press the DISPLAY ACCESS [HOME] button, then press the [F1] button to display the Meter | CH1-32 page.
7 Make sure that [ON] button indicators 9 and 10 are steadily lit.
8 While the musicians play the musical instruments, raise faders 9 and 10 to
set the appropriate monitoring level.
If necessary, play back the recording on the digital MTR and adjust the volume balance
between the recorded and recording signals.
Recording
1 Start recording on the digital MTR, and cue the musicians to start playing
the musical instruments while monitoring the recorded tracks.
During recording, display the Meter | CH1-32 page, and confirm that the Input Channel
levels are not clipping.
2 When the musicians finish playing, stop the digital MTR.
3 To check the recording, play the digital MTR from the beginning.
4 If you are satisfied with the recording, stop the playback and disarm Tracks
9 and 10 on the recorder.
01V96 Version 2—Owner’s Manual
Mixing Recorded Tracks into Stereo (Mixdown)
63
Mixing Recorded Tracks into Stereo (Mixdown)
“Mixdown” is the process of mixing recorded tracks into stereo and recording the stereo signal to an external master recorder. This section describes how to mix signals recorded on
Tracks 1–16 into a stereo signal, then apply the 01V96’s internal effects to the signal, then
record it to an external master recorder.
Connecting and Setting Up the Master Recorder
Follow the steps below to connect a DAT recorder, MD recorder, CD recorder or other master recorder to the 01V96. Change the 01V96’s internal patch so that you can monitor the
playback signal on the master recorder through ST IN Channel 2.
CH1-4
1
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
CH9-12
PHANTOM +48V
L
A
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
R
B
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
2TR OUT DIGITAL
connector
DIGITAL
IN
connector
Master recorder
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
MONITOR
2TR IN
PAD
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
+4 GAIN -26
-60
GAIN
13
LEVEL
PEAK
16
SIGNAL
UTILITY
PATCH
STORE
RECALL
SOLO
CLEAR
SELECTED CHANNEL
0
-3
PAN
-6
EQ
DYNAMICS
EFFECT
DEC
INC
-9
VIEW
10
2TR IN DIGITAL
connector
SCENE MEMORY
MIDI
PAIR/
GROUP
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
+4 GAIN -26
PEAK
14 15
SIGNAL
DIGITAL
OUT
connector
-12
FADER MODE
-15
EQUALIZER
-18
-24
-30
AUX 1
AUX 2
AUX 3
AUX 4
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
AUX 7
AUX 8
HIGH-MID
FREQUENCY
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
+10
2
0 +10
5
3
0 +10
5
5
5
0
15
15
15
15
15
15
15
20 10
15
15
15
15
16
0 +10
5
5
0
5
5
10
10
15
15
20 10
20
20
15
10
10
5
15
5
15
5
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
30
40
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ON
ST IN 2
5
0
0
20 10
10
5
SEL
SOLO
ON
0
20 10
15
SEL
SOLO
ST IN 1
0
5
5
0
ON
20 10
10
5
20 10
15
0 +10
5
5
0
10
5
20 10
14
0 +10
5
5
0
10
5
20 10
13
0 +10
5
5
0
10
5
20 10
12
0 +10
5
5
0
10
5
20 10
11
0 +10
5
5
0
10
5
20 10
10
0 +10
5
5
0
10
5
9
0 +10
5
5
0
10
5
20 10
0 +10
5
5
0
10
5
20 10
8
7
0 +10
5
5
0
10
5
20 10
6
0 +10
5
5
0
10
5
20 10
5
0 +10
5
5
0
10
5
10
4
0 +10
SEL
15
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
Tip: To monitor the master recorder’s playback signals, you can also connect the analog output
of the master recorder to the 01V96 2TR IN connector. In this way, you can quickly switch the
monitoring signal using the Monitor Source selector in the MONITOR OUT section.
2 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | In
Patch page appears.
01V96 Version 2—Owner’s Manual
5
Tutorial
1 Connect a master recorder to the 01V96.
In the following example, the 01V96 2TR OUT DIGITAL connector is connected to the
master recorder’s digital input, and the 01V96 2TR IN DIGITAL connector is connected to
the master recorder’s digital output.
64
Chapter 5—Tutorial
3 Move the cursor to the 2L parameter box in the STEREO INPUT section,
rotate the Parameter wheel or press the [INC]/[DEC] buttons to select “2TD
L,” then press [ENTER].
4 In the same way, move the cursor to the 2R parameter box in the STEREO
INPUT section, then select “2TD R.”
The signals input at the 2TR IN DIGITAL connector are now routed to ST IN Channel 2 L
and R.
5 Use the ST IN [ST IN] button to select ST IN Channels 1 and 2.
The ST IN [ST IN] button selects an ST IN channel pair (ST
IN Channels 1 and 2 or 3 and 4) which you can control using
the buttons and controls in the ST IN section. The indicators
to the right of the button indicate which ST IN channels are
currently selected.
Lights up.
ST IN
6 Turn off the [ON] button for ST IN Channel 2.
The button indicator turns off.
This [ON] button should be turned on only when you monitor the playback signal of the
master recorder.
Adjusting the Track Mix Balance
Follow the steps below to adjust the mix balance among Tracks 1–16 and process the signals
using the EQ, compressor and gate.
1 Make sure that Tracks 1–16 on the digital MTR are all disarmed and the
recorder is in a mode that enables you to monitor the track playback signals.
2 Press the LAYER [1–16] button, then turn off the [ON] buttons for Input
Channels 1–16.
3 Press the LAYER [17–32] button and make sure that the [ON] buttons for
Input Channels 17–32 are turned on.
4 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
Pan/Route | Rout17–STI page appears. On this page, make sure that the S
buttons for Input Channels 17–32 are turned on, and the 1–8 buttons are
turned off.
01V96 Version 2—Owner’s Manual
Mixing Recorded Tracks into Stereo (Mixdown)
65
5
5 Use the PAN parameter controls for Input Channels 17–32 on the page to
adjust the panpot for each track.
Tip: Alternatively, you can adjust the pan settings by selecting the Input Channels via the corresponding [SEL] button, then rotating the SELECTED CHANNEL [PAN] control.
6 Raise the [STEREO] fader to 0 dB.
7 While playing back the recording on the digital MTR from the beginning,
operate faders 1–16 to adjust the mix balance among the tracks.
• EQ’ing the track signals
Select the desired channel by pressing the corresponding [SEL] button, press the [EQ] button, then press the [F1] button to display the EQ Edit page (see page 84). Alternatively,
adjust the EQ parameters using the buttons and controls in the SELECTED CHANNEL section.
• Compressing the track signals
Select the desired channel by pressing the corresponding [SEL] button, press the [DYNAMICS] button, then press the [F4] button to display the Dynamics | Comp Lib page and recall
the desired compressor program (see page 82). Press the [DYNAMICS] button, then press
the [F3] button to display the Comp Edit page, then edit the compressor parameters.
• Gating the track signals
Select the desired channel by pressing the corresponding [SEL] button, press the [DYNAMICS] button, then press the [F2] button to display the Dynamics | Gate Lib page. Then, recall
the desired gate program. Press the [DYNAMICS] button, then press the [F1] button to display the Gate Edit page, then edit the gate parameters.
01V96 Version 2—Owner’s Manual
Tutorial
Input Channel 17–32 signals input from Tracks 1–16 of the digital MTR are now routed
through the Stereo Bus, to the STEREO OUT and 2TR OUT DIGITAL connectors.
66
Chapter 5—Tutorial
Using the Internal Effects
The 01V96 features four internal multi-effects processors that can be used via Aux Sends
and Returns or by inserting them into specific channels. This section describes how to use
internal Effects processor 1 via Aux Send 1, and apply reverb to the track signals.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | Effect
page appears.
This page enables you to patch the inputs and outputs of Effects processors 1–4. By default,
Aux Send 1 is patched to the input of Effects processor 1, and the output of Effects processor
1 is patched to ST IN Channel 1 L and R, as shown in the diagram above.
Tip: If the patch for internal Effects processor 1 is different from the above, use the Parameter
wheel or [INC]/[DEC] buttons, and the [ENTER] button to change the patch.
2 Make sure that the [ON] button for ST IN Channel 1 in the ST IN section is
turned on.
3 Press the DISPLAY ACCESS [EFFECT] button repeatedly until the Effect | FX1
Lib page appears.
The Effect | FX1 Lib page enables you to recall effect programs to be used by Effects processor 1 from the Effects library, and store the current effects settings of Effects processor 1 to
the Effects library.
Select from the list in the center column a program memory to which you wish to store the
effects settings, or a program memory that you wish to recall. The selected program appears
inside the dotted box.
01V96 Version 2—Owner’s Manual
Mixing Recorded Tracks into Stereo (Mixdown)
67
4 Rotate the Parameter wheel and select “2. Reverb Room”
For purposes of this tutorial, select this room reverb program.
Tip: To edit the effect parameters, press the [EFFECT] button
repeatedly until the Effect | FX1 Edit page appears (see page 161).
6 Press the LAYER [17–32] button.
Input Channel Layer 17–32 is selected for control from the channel
strip section.
7 Press the FADER MODE [AUX1] button.
The button indicator lights up.
While the [AUX 1]–[AUX 8] button indicators are lit, faders 1–16 control the Aux 1–8 send
levels.
In this example, the faders control the send level of the signals routed from Input Channels
17–32 to Aux 1 (Effects processor 1 input).
Tip: To reset the fader 1–16 function to normal mode, press the FADER MODE [HOME]
button.
8 While playing back the recording on the digital MTR from the beginning,
operate faders 1–16 to adjust the send level of the signals routed from Input
Channels to Effects processor 1.
9 To adjust the effect return level, use the rotary level control located on the
left side of the ST IN section on the top panel.
You can view the current level in the upper-right corner of the display.
01V96 Version 2—Owner’s Manual
5
Tutorial
5 Move the cursor to the RECALL button located to the left of the list, then
press [ENTER].
Effect program “Reverb Room” is loaded into Effects processor 1.
68
Chapter 5—Tutorial
Recording to the Master Recorder
Follow the steps below to record the mixed stereo signal from the 01V96 to the connected
master recorder.
1 Start recording on the master recorder, then start playing back on the digital
MTR.
During recording, observe the stereo meter on the right of the display and confirm that the
stereo output level is not clipping.
2 When the playback is finished, stop the master recorder, then stop the digital
MTR.
3 Turn on the [ON] button for ST IN Channel 2 in the ST IN section. The button
indicator lights up.
4 Play back the recording on the master recorder.
The playback signal is input at the 01V96’s 2TR IN DIGITAL connector, then routed
through ST IN Channel 2 to the Stereo bus.
Note: Most consumer-type DAT recorders and MD recorders are unable to synchronize to
external wordclock during playback (that is, they cannot be wordclock slaves). If this type of
master recorder is connected to the 01V96’s 2TR IN DIGITAL connector, access the DIO/Setup
| Word Clock page and select “2TRD” (2TR IN DIGITAL) as the wordclock source.
When the master recorder finishes playing back, turn off the [ON] button for ST IN Channel 2.
Tip: If you desire, you can store the current mix settings to memory as a Scene (see page 165).
01V96 Version 2—Owner’s Manual
Analog I/O & Digital I/O
69
6 Analog I/O & Digital I/O
This chapter describes the 01V96’s analog and digital input/output connectors as well as the
basic operations involving the digital I/Os.
Analog Inputs & Outputs
Input Section
The 01V96’s top panel features input connectors, which enable you to connect microphone
and line-level sources.
• INPUT connectors B 1–12
A
A
These balanced TRS-type connectors accept line-level and microB
B
phone signals. The nominal input range is –60 dB through +4 dB.
You cannot use same-numbered INPUT A and INPUT B connectors
simultaneously. (For example, you cannot use INPUT A-2 and
INPUT B-2 at the same time.) If you connect cables to A and B connectors of the same number, only the signal from INPUT B is effective (e.g., B-2 takes priority over A-2).
INPUT
(BAL)
• INPUT connectors 13–16
These balanced TRS-type phone connectors accept line-level signals.
13
15
When the AD 15/16 source selector is turned on (pushed in), signals
from INPUT 15 and 16 are ignored. Instead, signals from the 2TR IN
14
16
connector will be routed to AD Input Channels 15 and 16.
Tip: You can patch signals input from the INPUT connectors to any Input Channels. (See
page 121 for information on patching input signals to Input Channels.)
• INSERT I/O connectors
These TRS-type phone connectors are used to insert external
devices, such as effects processors, into AD Input Channels.
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
• Phantom Power
Inputs 1 through 12 feature switchable +48V phantom
powering for use with condenser-type microphones
and direct boxes. The phantom [+48V] switches on
the rear panel turn on or off the +48V phantom power
feed to the corresponding inputs.
• PAD switches
PAD
20dB
Inputs 1 through 12 feature pad switches, which attenuate input signals by 20 dB. These switches are effective on both INPUT A and B
signals.
01V96 Version 2—Owner’s Manual
6
Analog I/O & Digital I/O
• INPUT connectors A 1–12
These balanced TRS-type phone connectors accept line-level and
1
2
microphone signals. The nominal input range is –60 dB through
+4 dB. The phantom [+48V] switches on the rear panel turn on or
A
A
off the +48V phantom power feed to these inputs.
70
Chapter 6—Analog I/O & Digital I/O
• GAIN controls
-60
-16
GAIN
PEAK
SIGNAL
Inputs 1 through 16 feature rotary gain controls that adjust input
sensitivity. Input sensitivity for INPUT connectors 1–12 ranges from
–16 dB to –60 dB when the Pad is off, and from +4 dB to –40 dB
when the Pad is on. Input sensitivity for INPUT connectors 13–16
ranges from +4 dB to –26 dB.
• PEAK & SIGNAL Indicators
GAIN
The SIGNAL indicator lights up when the input signal level at
PEAK
INPUTs 1–16 exceeds –34 dB. The PEAK indicator lights up when
SIGNAL
the input signal level is 3 dB below clipping.
• 2TR IN connectors
These unbalanced RCA phono connectors accept line-level signals
from master recorders.
When the AD 15/16 source selector is turned on (pushed in), signals
input at these conductors are routed to AD Inputs 15 and 16. When
the Monitor source selector is turned on (pushed in), you can monitor these signals from the MONITOR OUT connectors.
L
R
IN
OUT
2TR
-10dBV (UNBAL)
Output Section
The 01V96 top and rear panels feature output connectors that enable you to connect a monitoring system, master recorder, effects processors and other line-level devices.
• MONITOR OUT connectors L/R
These balanced TRS-type phone connectors output monitoring signals or input signals routed from the 2TR IN connectors. The nominal output level is +4 dB.
Use the Monitor source selector in the AD Input section to select the
signal output from these connectors.
• OMNI OUT connectors 1–4
These balanced TRS-type phone connectors output any
Bus Outs or Input Channel Direct Outs. The nominal output level is +4 dB.
Tip: Any signal path can be patched to the OMNI OUT connectors. (See page 124 for more
information on patching signals to the OMNI OUT connectors.)
• STEREO OUT connectors L/R
These balanced XLR-3-32-type connectors output the Stereo Out
signals. The nominal output level is +4 dB.
• 2TR OUT connectors
These unbalanced RCA phono connectors output line-level signals
L
to a connected master recorder or other external device. These
connectors always output the Stereo Out signals.
R
IN
OUT
2TR
-10dBV (UNBAL)
01V96 Version 2—Owner’s Manual
Digital Inputs & Outputs
71
Digital Inputs & Outputs
The 01V96 rear panel features digital input and output connectors that enable you to connect external digital devices. Any signal path can be patched to these digital inputs and outputs.
You can also add analog and digital I/Os by installing an optional I/O card in the slot.
Digital I/O Connectors
• 2TR IN DIGITAL connector
2TR IN DIGITAL is an RCA phono connector and accepts consumer
format (IEC-60958) digital audio. You can patch digital signals input
at this connector to any Input Channel (page 121).
6
• ADAT IN connector
This TOSLINK connector accepts 8-channel ADAT optical format signals, which can be
patched to any Input Channel (page 121).
• ADAT OUT connector
This TOSLINK connector outputs an 8-channel ADAT optical format signal. You can patch
any Bus Outs or Input Channel Direct outs to this output (page 123).
SLOT
This slot allows you to install an optional mini-YGDAI (Yamaha General Digital Audio
Interface) I/O card. This card offers AD/DA conversion, and various analog I/O options and
digital I/O interfaces in all the popular digital audio interconnect formats, including
AES/EBU, ADAT, and Tascam. You can patch signals input at these card connectors to any
Input Channels or Insert Ins (see page 122).
You can patch the card outputs to Bus Outs or Input Channel Direct Outs (see page 125).
The following mini-YGDAI I/O cards are currently available.
Card
Format
In
Out
MY8-AD
MY8-AD241
MY4-AD
Analog in
Phone jack (balanced) x8
—
XLR-3-31 type (balanced) x4
8
Analog out
—
24-bit, 44.1/48/88.2/96 kHz D-sub 25-pin
4
8
8
MY8-AE2
8
8
16
16
8
8
AES/EBU I/O
20-bit, 44.1/48 kHz
XLR-3-32 type (balanced) x4
8
MY8-ADDA96 Analog
in/out
MY8-AEB
24-bit, 44.1/48 kHz
4
MY8-AD96
MY16-AE2
Connectors
20-bit, 44.1/48 kHz
8
MY4-DA
MY8-DA96
Resolution/Sampling Rate
D-sub 25-pin
24-bit, 44.1/48/88.2/96 kHz
24-bit, 44.1/48 kHz
Euroblock x4
D-sub 25-pin
BNC connector x8
01V96 Version 2—Owner’s Manual
Analog I/O & Digital I/O
• 2TR OUT DIGITAL connector
This RCA phono connector outputs consumer format (IEC-60958)
digital audio. You can patch any Bus outs or Input channel Direct
Outs to this output (page 125).
72
Chapter 6—Analog I/O & Digital I/O
Card
Format
In
Out
Resolution/Sampling Rate
Connectors
AES/EBU I/O
8
8
8
8
Optical x2
16
16
Optical x4
8
8
MY8-AE96
MY8-AE96S3
MY8-AT2
MY16-AT2
ADAT I/O
MY8-TD2
24-bit, 44.1/48 kHz
Tascam
MY16-TD2
MY8-mLAN2
MY16-mLAN2
16
16
8
8
16
16
ADAT
8
8
D-sub 25-pin
BNC wordclock output
D-sub 25-pin
IEEE1394
6-pin 1394 connector x2
WAVES Y56K
WAVES Y96K
24-bit, 44.1/48/88.2/96 kHz D-sub 25-pin
24-bit, 44.1/48 kHz
24-bit, 44.1/48/88.2/96 kHz
Optical x2
1. This card is a substitution for a 20-bit MY8-AD card.
2. These cards support 24-bit/96 kHz in Double Channel mode. (Separate 96 kHz wordclock required.)
3. This card is identical to the MY8-AE96, except that it features a sampling rate converter.
See the Yamaha Professional Audio Web site at the following URL for up-to-date news on
I/O cards:
<http://www.yamahaproaudio.com/>.
Converting Sampling Rates of Signals Received at I/O
Card Inputs
An optional MY8-AE96S Digital I/O card features sampling rate converters, so you can easily convert the sampling frequency of digital inputs to the current 01V96 sampling rate.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Format page appears.
Use the buttons in the SRC sections to turn the sampling rate converters on and off. You can
turn the sampling rate converters of the digital I/O card on or off in pairs (odd & even channels, in this order).
Tip: The FS box on the Word Clock page displays the sampling frequency at which the 01V96
is currently operating.
Note: The sampling rate converter is available only on the Yamaha MY8-AE96S Digital I/O
card. If you have installed another type of I/O card in the slot, or if no card is installed in the
01V96, the buttons in the SRC sections are disabled.
01V96 Version 2—Owner’s Manual
Monitoring Digital Input Channel Status
73
2 Use the cursor buttons to move the cursor to any two-channel button in the
SRC sections, then press [ENTER].
The sampling rate converter for the selected 2-channel input turns on or off. When on, the
sampling rate of the received digital audio is converted to the 01V96’s current sampling rate.
Monitoring Digital Input Channel Status
You can view and monitor the Channel Status (sampling rate, emphasis, etc.) of digital
audio signals connected to the 2TR Digital Inputs and Slot Inputs as follows.
1 Press the DISPLAY ACCESS [UTILITY] button, then press the [F2] button.
The Utility / CH Status page appears.
6
Analog I/O & Digital I/O
1
2
3
4
5
6
On this page, use the following buttons to select a slot or connector for which you want to
view the channel status.
A 2TR IN
This button enables you to view the Channel Status of input signals connected to the
2TR Digital Inputs.
B SLOT
These buttons enable you to view the Channel Status of each two adjacent (odd and
even, in this order) channel signals connected to the digital I/O card installed in the slot.
2 Move the cursor to the desired input or slot button, then press [ENTER].
Channel Status information for the selected input is displayed. However, if a mini-YGDAI
I/O card other than AES/EBU format is installed, Channel Status information will be grayed
out. Channel Status information includes the following items:
C FS
Indicates the sampling rate. If no signal is being input, or if the incoming wordclock is
not synching to the internal clock, “Unlock” appears.
D EMPHASIS
Indicates the Emphasis on/off status.
E CATEGORY
Indicates the status of “Category Code Bit” included in the IEC958 Part 2 (S/PDIF-Consumer) format. This parameter can display the following values:
Parameter value
Description
General
Temporarily used
Laser Optical
Laser optical device
D/D Conv
Digital - Digital converter and signal processing device
01V96 Version 2—Owner’s Manual
74
Chapter 6—Analog I/O & Digital I/O
Parameter value
Description
Magnetic
Magnetic tape device and magnetic disk device
D.Broadcast
Digital broadcast reception
Instruments
Musical instrument, microphone, and sources that
generate string signals
A/D Conv
A/D converter (without copyright information)
A/D Conv with (C)
A/D converter (with copyright information)
Solid Memory
Solid memory device
Experimental
Experimental device
Unknown
Unknown
Note: “AES/EBU” appears in the Category row when you are monitoring IEC958 Part 3
(AES/EBU-Professional) format signals (that do not include Category Code Bit).
F COPY
Indicates the status of copy protection information included in the IEC958 Part2
(S/PDIF-Consumer) format signals. “OK” appears if copying is allowed. “Prohibit”
appears if copy-protected.
3 If you select the SLOT button for a slot that has an
MY16-AE card installed, use the 01–08 and 09–16 buttons located in the lower-right corner of the screen
to select a channel group you wish to display.
Dithering Digital Outputs
When digital audio is transferred to lower-resolution systems, truncated bits may generate
unpleasant noise. To cancel the audible effect of this noise, a small complement of noise is
intentionally added to the digital outputs. This process is called “dithering.”
On the 01V96, you can dither the 2TR Digital Outputs and Slot Outputs. For example, you
can apply dithering to the 01V96 stereo mix data and record to a 16-bit DAT recorder.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Format page appears.
The dithering settings are displayed at the bottom of the page.
01V96 Version 2—Owner’s Manual
Setting the Transfer Format for Higher Sampling Rates
75
2 Move the cursor to the output or channel to which you want to apply dithering, then rotate the Parameter wheel or press the [INC]/[DEC] buttons to
select the value that matches the resolution of the receiving device.
Note:
• You cannot apply dithering to outputs or channels that are set to “OFF.”
• Dithering is effective only when the resolution of the receiving device is lower than that of
the 01V96.
Tip: To copy the currently-selected setting to all channels, double-click the [ENTER] button.
The copy confirmation window is displayed.
Setting the Transfer Format for Higher Sampling Rates
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Word Clock page appears.
2 Select INT88.2k or INT96k as the wordclock source.
Note: When the 01V96 operates at a high sampling rate (88.2 kHz or 96 kHz), only two internal effects processors are available.
3 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Format page appears.
1
4 Use the cursor buttons to move the cursor to an IN/OUT parameter field
(1), then rotate the Parameter wheel or press the [INC]/[DEC] buttons to
set the data transfer format.
The IN/OUT parameters are used to set one of the following data transfer formats for each
slot input and output.
01V96 Version 2—Owner’s Manual
6
Analog I/O & Digital I/O
To operate the 01V96 at higher sampling frequencies (88.2 kHz or 96 kHz) and transfer digital audio signals to and from connected external devices, you must set the data transfer format in accordance with the sampling frequencies supported by the external devices.
76
Chapter 6—Analog I/O & Digital I/O
• DOUBLE CHANNEL
In Double Channel mode, digital audio data is received and transmitted as mono signals at
a sampling rate that is exactly half (44.1/48 kHz) the current higher sampling rate. Data is
handled by two channels. This is useful when you wish to transfer data between the 01V96
running at a higher sampling rate and legacy 44.1/48 kHz digital MTRs or HDRs.
Note: Double Channel mode reduces the total number of inputs or outputs on the corresponding slot. The even-numbered channels are disabled.
• DOUBLE SPEED
In Double Speed mode, digital audio data is received and transmitted at the current high
sampling rate (i.e., 88.2 kHz or 96 kHz). Select this mode if the devices that support the
higher sampling rates transmit or receive data.
Note: You can select this setting only for slots in which a digital I/O card that inputs/outputs
double-speed digital audio data (e.g., MY8-AE96, MY8-AE96S) is installed.
• SINGLE
In Single mode, digital audio data is received and transmitted at a sampling rate that is half
(44.1/48 kHz) the current higher sampling rate of the 01V96. For example, this is useful
when you wish to send 44.1 kHz digital signals from an external HDR to the 01V96 running
at 88.2 kHz.
Note: You cannot select this setting for slots in which a digital I/O card that inputs/outputs
double-speed digital audio data (e.g., MY8-AE96, MY8-AE96S) is installed.
Tip: The parameter fields display “–” if the slot contains no I/O card or if an AD/DA card or
other I/O card that does not allow you to set the transfer format has been installed.
01V96 Version 2—Owner’s Manual
Input Channels
77
7 Input Channels
This chapter describes how to adjust the 01V96’s Input Channel parameters.
About Input Channels
The input Channel section enables you to adjust the level and tone of the signals input to
the 01V96 (and the signals output from the internal Effects processors 1–4), and route the
signals to Buses 1–8, the Stereo Bus, and Aux Sends 1–8. There are two types of Input Channels, each featuring slightly different functions: monaural Input Channels 1–32 and stereo
ST IN Channels 1–4.
Input Channels 1–32
Each of these monaural Input Channels features a phase effect, gate, compressor, attenuator, and EQ for signal processing. The following diagram illustrates the Input Channel 1–32
signal flow.
7
INPUT PATCH
Input Channels
Input Channels 1–32 feature the following parameters:
•
(Phase)
This section switches the phase of input signals.
• GATE
This dynamics processor can be used as a gate or for ducking.
• COMP (Compressor)
This dynamics processor can be used as compressor, expander or limiter. The compressor
can be pre-EQ, pre-fader, or post-fader.
• ATT (Attenuator)
This section enables you to attenuate or amplify the level of signals that will be input to the
EQ. The attenuator enables you to prevent post-EQ signals from clipping and to correct signal levels that are too low.
• 4 BAND EQ (4-band equalizer)
This parametric EQ features four bands (high, high-mid, low-mid, and low).
• INPUT DELAY (Input delay)
This section enables you to delay input signals. You can use this delay to fine-tune the timing
between channels, or as a delay effect with feedback.
01V96 Version 2—Owner’s Manual
78
Chapter 7—Input Channels
• ON (On/Off)
This section enables you to turn the channel on or off. The channel is muted with the Off
setting.
• LEVEL
This section enables you to adjust the input level of the Input Channel signal.
• PAN
This section enables you to adjust the pan setting of the signals routed from the Input Channels to the Stereo Bus. You can also apply the pan setting to a pair of Bus channels.
• AUX (Aux Send level)
This section enables you to adjust the level of signals routed to Aux Sends 1–8. The signals
can be routed to Aux Sends from either the pre-fader or post-fader position.
• INSERT
This section enables you to patch input signals to external devices via the on-board I/O connectors or I/O card, or insert the internal effect processors. You can patch any inputs, outputs, or I/O card channels. (Note that this is different from the INSERT I/O connectors in
the AD Input section.)
• METER
This section enables you to switch the metering position of the signal levels that are displayed in the Meter page. (See page 34 for more information on selecting the metering position.)
ST IN Channels 1–4
INPUT PATCH
These stereo channels enable you to process stereo signals using the phase effect, attenuator,
and EQ. The following diagram illustrates the ST IN Channel 1–4 signal flow.
ST IN Channels 1–4 feature the following parameters:
•
•
•
•
•
•
•
•
(Phase)
ATT (Attenuator)
4 BAND EQ (4-band equalizer)
ON (On/Off)
LEVEL
PAN
AUX (Aux Send level)
METER
01V96 Version 2—Owner’s Manual
Setting the Input Channels from the Display
79
Refer to the description of Input Channels for more information on these parameters
(page 77).
Tip: You can store these channel parameter settings in the Channel library. You can also store
the Gate, Compressor, and EQ parameter settings to the corresponding libraries.
Setting the Input Channels from the Display
To set the Input Channel parameters, you can either move the cursor to the desired parameter on the display and change the value, or operate the desired button or control on the top
panel to directly change the setting.
This section explains how to set the parameters via the display.
Switching the Signal Phase
1
2
A NOR/REV
These buttons switch the corresponding Input Channel phase. NOR buttons indicate
normal phase, and REV buttons indicate reversed phase.
B GLOBAL
The GLOBAL NOR/REV buttons allow you to set the phase for all Input Channels
simultaneously.
Tip:
• The name of the currently-selected channel is indicated in the upper-right corner of the
screen.
• You can set the phase separately for each of the ST IN Channels or for each channel in a
channel pair. If you selected the desired ST IN Channel using the corresponding [SEL] button, pressing the same [SEL] button repeatedly will toggle between channels L and R.
01V96 Version 2—Owner’s Manual
7
Input Channels
To switch the phase of each Input Channel, press the [ /INSERT/DELAY] button repeatedly until the following /INS/DLY | Phase page appears.
Move the cursor to the NOR/REV button of the channel for which you want to change the
phase, then press the [ENTER] or [INC]/[DEC] buttons to change the setting.
80
Chapter 7—Input Channels
Delaying Input Channels
To set the delay for each channel, press the [ /INSERT/DELAY] button repeatedly until
the page listed below that contains the desired channels appears.
- DLY 1-16 page
This page enables you to set the Delay function for Input Channels 1–16.
- DLY 17-32 page
This page enables you to set the Delay function for Input Channels 17–32.
The parameters on these two pages (and the procedure for setting them) are the same.
1
2
3
A DELAY SCALE
•
•
•
•
•
The following buttons determine the units of the delay value shown below the msec
value.
meter ............................. Units are set to meters.
feet ................................. Units are set to feet.
sample ........................... Units are set to samples.
beat ................................ Units are set to beats.
frame ............................. Units are set to timecode frames.
B GANG button
When this button is turned on (highlighted), the delay time for each channel in a channel pair can be set simultaneously. When this option is turned off, the delay time can be
set for each channel in a channel pair individually.
C Channel section
•
•
•
•
•
You can set individual delay parameters here. The delay parameters include the following items:
ON/OFF ........................ This button switches the corresponding channel delay on or
off.
msec............................... This parameter sets the delay time in milliseconds.
meter/feet/sample/
beat/frame .................... The delay time can be set using units of meters, feet, samples,
beats, or frames, which you select by using the DELAY SCALE
buttons.
MIX................................ This parameter sets the mix balance of dry (Input Channel)
and wet (delayed) signals.
FB.GAIN ....................... This parameter sets the amount of delay feedback.
01V96 Version 2—Owner’s Manual
Setting the Input Channels from the Display
81
Tip:
• This function is unavailable for the ST IN Channels.
• The delay time range depends on the sampling rate at which the 01V96 is operating. (For
example, at 44.1 kHz, the range is 0 through 984.1 msec.)
• If you select the DELAY SCALE meter or feet button, the distance value can be converted to
the delay time based on sonic speeds (about 340 m/sec at 15 degrees Celsius). This option is
useful if you wish to correct the timing difference between two sound sources that are far
apart.
• If you select the DELAY SCALE beat button, a parameter box for setting a note that represents the beat and a parameter box for a tempo (BPM) setting appear below the DELAY
SCALE parameter. Setting the note and BPM settings in these parameter boxes enables you
to set a delay time that synchronizes to the song tempo.
Gating Input Channels
To set the Input Channel gates, use the [SEL] buttons to select the desired Input Channel,
then press the DISPLAY ACCESS [DYNAMICS] button, then press the [F1] button. The
Dynamics | Gate Edit page appears.
Input Channels
2
7
3
4
1
5
7
6
A KEYIN SOURCE
Select one of the following buttons to determine the trigger source for the currently-selected Input Channel’s gate.
• SELF ...............................The selected channel’s own input signal is the trigger source.
• CHANNEL ....................Another Channel’s input signal is the trigger source. Select the
desired channel in the parameter box below the CHANNEL
button.
• AUX................................An Aux Send signal is the trigger source. Select the desired bus
in the parameter box below the AUX button.
B STEREO LINK
This parameter’s ON/OFF button enables you to pair gates for stereo operation even
when the Input Channels are not paired.
C CURVE
This area displays the current gate curve.
D TYPE
This area displays the current gate type (GATE or DUCKING).
Note: You cannot change the gate type on this page. To change the gate type, recall a program
that uses the desired gate type from the Gate library.
01V96 Version 2—Owner’s Manual
82
Chapter 7—Input Channels
E Meters
These meters indicate the levels of the post-gate signals and the amount of gain reduction.
F ON/OFF
The ON/OFF button turns the currently-selected Input Channel’s gate on or off.
G PARAMETER
These controls enable you to set the gate parameters. (See page 272 for more information on the parameters.)
Tip:
• This function is unavailable for the ST IN Channels.
• You can store the gate settings in the Gate library, which features preset programs that can
be used for various applications (see page 183).
Compressing Input Channels
To set the Input Channel compressors, use the [SEL] buttons to select the desired Input
Channel, then press the DISPLAY ACCESS [DYNAMICS] button, then press the [F3] button to display the Dynamics | Comp Edit page.
2
3
1
4
5
6
7
A POSITION
Use the Parameter wheel, or the [INC]/[DEC] buttons to select the position of the compressor within the channel from the following options:
• PRE EQ.......................... Immediately before EQ (default)
• PRE FADER .................. Immediately before the fader
• POST FADER ............... Immediately after the fader
B STEREO LINK
This ON/OFF button enables you to pair compressors for stereo operation even when
channels are not paired.
C CURVE
This area displays the current compressor curve.
D TYPE
This field indicates the compressor type used by the currently-selected channel’s compressor (COMP/EXPAND/COMP (H)/COMP (S)).
Note: You cannot change the Compressor type on this page. To change the compressor type,
recall a program that uses the desired compressor type from the compressor library.
01V96 Version 2—Owner’s Manual
Setting the Input Channels from the Display
83
E Meters
These meters indicate the levels of the post-compressor signals and the amount of gain
reduction.
F ON/OFF
The ON/OFF button turns the currently-selected Input Channel’s compressor on or off.
G PARAMETER section
These controls enable you to set the compressor parameters. (See page 273 for more
information on the parameters of each compressor type.)
Tip:
• This function is unavailable for the ST IN Channels.
• You can store the compressor settings in the compressor library, which features preset programs that can be used for various applications (see page 185).
Attenuating Input Channels
Move the cursor to the knob for the desired Input Channel, then rotate the Parameter wheel
to set the amount of attenuation in the range of –96 dB to +12 dB.
Tip: You can also set the attenuation amount (in dB) for the currently-selected channel on
the EQ | EQ Edit page.
01V96 Version 2—Owner’s Manual
7
Input Channels
To set the attenuator for each Input Channel, press the DISPLAY ACCESS [EQ] button,
then press the [F3] button to display the EQ | In Att page.
84
Chapter 7—Input Channels
EQ’ing Input Channels
The 01V96’s Input Channels feature 4-band (LOW, LOW-MID, HIGH-MID, HIGH) parametric EQ. The LOW-MID and HIGH-MID bands are a peaking type of EQ. The LOW and
HIGH bands can be set to shelving, peaking, or HPF and LPF respectively.
1 Press the [SEL] button of the channel for which you want to adjust EQ.
2 Press the DISPLAY ACCEESS [EQ] button, then press the [F1] button to display the EQ | EQ Edit page.
2
4
3
1
5
6
The parameters on this page are described below:
A EQ ON
The ON/OFF button turns the currently-selected Input Channel’s EQ on or off. You can
press the [ENTER] button to turn the EQ on or off as long as the cursor is located on
any parameter other than TYPE.
B TYPE
Selects the type of EQ. TYPE I is the EQ type used on legacy Yamaha 02R series digital
mixing consoles. TYPE II is a newly developed algorithm.
C ATT
Determines the amount of pre-EQ signal attenuation in dB. It is the same Attenuator
parameter that appears on the EQ | ATT In page.
D CURVE
This area displays the current EQ curve.
E Meters
These meters indicate the post-EQ signal levels of the currently-selected Input Channel
and its available pair partner.
F LOW, L-MID, H-MID, HIGH sections
These sections contain the Q, Frequency (F), and Gain (G) parameters for the four
bands. These parameter values range as follows:
Parameter
Q
Frequency
Gain
LOW
LOW-MID
HPF, 10.0 to 0.10
(41 steps), L.SHELF
HIGH-MID
10.0 to 0.10 (41 steps)
HIGH
LPF, 10.0 to 0.10
(41 steps), H.SHELF
21.2 Hz to 20.0 kHz (120 steps per 1/12 octave)
–18.0 dB to +18.0 dB (0.1 dB steps)1
1. The LOW and HIGH GAIN controls function as filter on/off controls when Q is set to HPF or LPF
respectively.
01V96 Version 2—Owner’s Manual
Setting the Input Channels from the Display
85
Tip:
• The LOW-band EQ functions as a high-pass filter when the Q parameter in the LOW section
is set to HPF. It functions as a shelving-type EQ when the Q parameter is set to L.SHELF.
• The HIGH-band EQ functions as a low-pass filter when the Q parameter in the HIGH section is set to LPF. It functions as a shelving-type EQ when the Q parameter is set to H.SHELF.
3 Move the cursor to the desired parameter, then rotate the Parameter wheel
to change the value.
Tip:
• The EQ settings for the ST IN Channels L & R are linked to each other.
• You can also press the buttons in the SELECTED CHANNEL section to select the desired
band and use the rotary controls to directly edit the Q, F, and G parameters (see page 91).
• You can store the EQ settings in the EQ library, which features preset programs that can be
used for various applications (see page 271).
Panning Input Channels
2
1
Move the cursor to the desired Pan control, then rotate the Parameter wheel to set the value.
A Pan controls
These knobs adjust the channel pan settings.
Press the [ENTER] button to reset the currently-selected Pan control to center.
B MODE
The MODE parameter determines how paired Input Channels are panned. There are
three Pan modes as follows:
• INDIVIDUAL...............In Individual mode, paired Input Channel
pan controls operate independently.
• GANG ............................In Gang mode, paired Input Channel pan
controls operate in unison, maintaining the
current pan range.
• INV GANG....................In Inverse Gang mode, paired Input Channel
pan controls operate in unison but move in
opposite directions.
01V96 Version 2—Owner’s Manual
7
Input Channels
Input Channels can be panned in the range of L63 through CENTER to R63. To pan each
channel, press the [PAN/ROUTING] button repeatedly until the Pan/Route | Pan page
appears.
86
Chapter 7—Input Channels
Tip:
• You can adjust the pan setting for the ST IN Channels L & R separately.
• You can also adjust the pan setting for the Input Channels using the PAN control in the
SELECTED CHANNEL section.
• Surround Pan is available when the 01V96 is in Surround mode. Refer to Chapter 12 for
more information on Surround Pan.
Routing Input Channels
You can route each Input Channel to the Stereo Bus, Bus 1–8, or its own Direct Out. With
the default setting, signals are routed only to the Stereo Bus. However, you can patch signals
to a single or multiple destinations, if necessary.
1 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
page listed below that contains the desired channels appears.
- ROUT1-16 page
This page enables you to change the routing for Input Channels 1–16.
- ROUT17-ST1 page
This page enables you to change the routing for Input Channels 17–32 and ST IN Channels 1-4.
The parameters on these two pages (and the procedure for setting them) are the same.
5
6
7
1
2
3
4
8
A PAN buttons
These buttons determine whether the channel’s Pan setting is applied to the Bus outs. In
surround mode, they also determine whether the Surround Pan setting is applied to the
Bus Outs.
B Bus buttons 1–8
These buttons route the currently-selected Input Channel to the Bus Outs. If the 01V96
is in Surround mode, the button indicators change as follows, depending on the selected
Surround mode:
Bus buttons
1
2
3
4
5
6
7
8
Surround mode: 3-1
L
R
C
S
5
6
Surround mode: 5.1
L
R
Ls
Rs
C
E
7
8
Surround mode: 6.1
L
R
Ls
Rs
C
Bs
E
8
7
8
L=Left, R=Right, C=Center, S=Surround, Ls=Left Surround
Rs=Right Surround, E=Low Frequency Effect, Bs=Back Surround
The above table shows the default assignment. The actual assignment may vary, depending on the settings on the DIO/Setup | Surround Bus Setup page.
01V96 Version 2—Owner’s Manual
Setting the Input Channels from the Display
87
CS
When this button is turned on, the currently-selected Input Channel is routed to the
Stereo Bus.
DD
When this button is turned on, the currently-selected Input Channel is routed to its
Direct Out. See page 125 for more information on the Direct Out.
E ALL STEREO
This button turns on the S button for all channels on the page.
F ALL BUS
This button turns on the Bus buttons 1–8 for all channels on the page.
G ALL CLEAR
This button clears all routing assignments on the page.
H SURROUND MODE
This field displays the current Surround mode.
Viewing Input Channel Settings
You can view and adjust parameter settings for the currently-selected Input Channel on the
View | Parameter or Fader pages.
■ Viewing the Gate, Compressor, and EQ Settings
To display the View | Parameter page for a specific Input Channel, use the corresponding
[SEL] button to select the desired channel, then press the DISPLAY ACCESS [VIEW] button repeatedly.
Move the cursor to a parameter you wish to change, then rotate the Parameter wheel or
press the [INC]/[DEC] buttons or [ENTER] button to modify the setting.
43
1
5
2
6
7
8
The following parameters are available (sections marked with an asterisk (*) are unavailable
for the ST IN Channels).
A GATE section (*)
This section enables you to turn the gate-type dynamics processor on or off and set the
parameters. (See page 81 for more information.)
01V96 Version 2—Owner’s Manual
7
Input Channels
Tip: The routings of the ST IN Channels L & R are linked. The D button is unavailable for
the ST IN Channels.
88
Chapter 7—Input Channels
B COMP section (*)
This section enables you to turn the compressor-type dynamics processor on or off and
set the parameters. (See page 82 for more information.)
C INSERT section (*)
This section enables you to turn the Insert on or off and patch the Insert In and Out.
(See page 127 for more information.)
D EQ section
This section enables you to set various EQ parameters. (See page 84 for more information.)
E Meters
These meters indicate the signal levels of the currently-selected Input Channel and its
available pair partner.
F
(Phase) section
You can reverse the signal phase of the currently-selected Input Channel. (See page 79
for more information.)
G DELAY section (*)
This section enables you to set the currently-selected channel’s Delay function. (See
page 80 for more information.)
H PAIR section (*)
This section indicates whether or not channels are paired. The heart icon ( ) is in one
piece when channels are paired. The heart icon is broken ( ) when channels are not
paired. (See page 92 for more information.)
■ Viewing the Pan, Fader, and Aux Send Level Settings
To display the View | Fader page of a certain Input Channel, use the corresponding [SEL]
button to select the desired channel, then press the DISPLAY ACCESS [VIEW] button
repeatedly.
Move the cursor to a parameter you wish to change, then rotate the Parameter wheel or
press the [INC]/[DEC] buttons to modify the setting.
1
2
3
4
5
6
A PAN/ON/Fader section
• PAN control.................. This control adjusts the currently-selected Input Channel’s Pan
parameter.
Press the [ENTER] button to reset the Pan control to Center.
01V96 Version 2—Owner’s Manual
Setting the Input Channels from the Display
89
• ON/OFF button ...........This button turns on or off the currently-selected Input Channel.
• Fader ..............................This parameter sets the fader position of the currently-selected
Input Channel. The fader knob is highlighted when the fader is
set to 0.0 dB.
Press the [ENTER] button to reset the Fader to 0.0 dB.
B SURROUND PAN section
• SURROUND PAN........The Surround pan parameters for the currently-selected Input
Channel are displayed only when a Surround mode is selected.
See page 135 for more information on Surround pan.
C BUS ROUTING/FOLLOW PAN section
D AUX section
• AUX................................These controls set the currently-selected Input Channel’s Aux
Send 1–8 levels and positions. (See page 109 for more information on Aux Sends.)
E Meter section
• Meters............................These meters indicate the levels of the currently-selected Input
Channel.
• PRE EQ/PRE FADER/POST FADER ...........The metering position is displayed below
the meters.
F GROUP section
• FADER/MUTE/EQ/COMP ............... These buttons indicate which Fader, Mute, EQ,
or Comp group, if any, the currently-selected
Input Channel is in. If the channel is in a group,
the group number appears. If the channel is not
in a group, “—” appears. (The compressor is
unavailable for the ST IN Channels.)
01V96 Version 2—Owner’s Manual
7
Input Channels
• BUS ROUTING ............This section enables you to select a destination Bus for the
selected channel. When the D button is turned on, the channel
signal is patched to the Direct Out selected in the parameter
box below the button. (The D button is unavailable for the ST
IN Channels.)
• FOLLOW PAN..............This button determines whether the Input Channel’s Pan setting is applied to the paired Bus Outs (Follow Pan function).
When the button is turned off, the Follow Pan function is disabled and an identical signal is sent to the paired Bus Outs. In
surround mode, it also determines whether the Surround Pan
setting is applied to the Bus Outs.
90
Chapter 7—Input Channels
Setting the Input Channels from the Control Surface
You can use the faders, [SEL] buttons, and various buttons and controls in the SELECTED
CHANNEL section on the top panel to directly control most parameters for Input Channels.
Setting Input Channel Levels and Panning the Channels
■ Input Channels 1–32
1 Press the LAYER [1–16] or [17–32] button to select a layer.
2 Press the [SEL] button of the channel for which you want to adjust the input
level and/or pan settings.
3 Use the faders to set the Input Channel levels.
4 Rotate the SELECTED CHANNEL [PAN] control to adjust the pan settings.
When you rotate the [PAN] control, the Pan/Route | Pan page is displayed automatically.
■ ST IN Channels 1–4
1 Use the ST IN [ST IN] button to select the desired ST IN Channels.
The indicators next to the [ST IN] button display the ST IN Channels currently selected for
control by the ST IN section.
2 Press the [SEL] button for the channel for which you want to adjust the level
and/or pan settings.
3 Rotate the level control of the desired channel to set the level.
You can always view the current channel level at the top of the display.
4 Rotate the SELECTED CHANNEL [PAN] control to adjust the pan setting.
The pan setting can be applied to either ST IN channel L or R. To switch between channels
L and R for the pan setting, press the same [SEL] button repeatedly. (The channel currently
being controlled is indicated in the upper-left corner of the display.)
01V96 Version 2—Owner’s Manual
Setting the Input Channels from the Control Surface
91
EQ’ing Input Channels
1 Press the [SEL] button or move the fader for the channel you wish to control.
2 To control EQ for the currently-selected channel, press one of the following
buttons to select the band you wish to adjust:
• [HIGH] button.............HIGH band
• [H-MID] button...........HIGH-MID band
• [L-MID] button............LOW-MID band
• [LOW] button ..............LOW band
3 Use the SELECTED CHANNEL [Q], [FREQUENCY], and [GAIN] controls to
adjust the Q, frequency, and gain of the band selected in Step 2.
When the Auto EQUALIZER Display (page 231) check box is on, the 01V96 displays the
EQ/EQ Edit page.
7
Input Channels
If the check box is off, the parameter value currently being adjusted pops up.
See page 84 for more information on EQ.
Tip:
• Pressing and holding down the button selected in Step 2 resets the corresponding band gain.
• Pressing the SELECTED CHANNEL [HIGH] and [LOW] buttons simultaneously resets the
Q, frequency and gain for each band.
01V96 Version 2—Owner’s Manual
92
Chapter 7—Input Channels
Pairing Input Channels
On the 01V96, you can pair adjacent odd-even Input Channels or counterpart channels on
Layer 1 and Layer 2 that share the same physical fader. Faders and most parameters of paired
channels are linked for stereo operation. Paired channels’ linked parameters and non-linked
parameters (that are available for independent control) are listed below:
Non-linked parameters
Linked parameters
[SEL] buttons
Input patches
Faders
Insert patches
Channel on/off
Output patches
Insert on/off
Comp insert position
Solo on/off
Phase
Solo Safe
Delay on/off
Aux on/off
Delay time*
Aux Send level
Delay feedback
Aux Sends as Pre or Post
Delay mix
Gate
Routing
Comp settings
Pan, Follow Pan
EQ settings
Surround pan
Fader group
Aux Send pan
Mute group
Balance
Fade time
Attenuators**
Recall Safe
* You can set this parameter for each channel independently if the GANG button is turned off on the
/INS/DLY |
DLY page.
** You can set this parameter for each channel independently on the EQ | ATT page, but the paired channel settings
are linked on the EQ | Edit and View pages.
Note: You cannot pair an ST IN channel 1–4 with an Input Channel.
To pair channels, or to cancel channel pairs, you can use the [SEL] buttons on the top panel
or access the Pair/Grup pages.
■ Pairing Channels by Using the [SEL] Buttons
1 While pressing and holding down the [SEL] button for one of the channels
you wish to pair, press the [SEL] button for the adjacent channel. (The paired
channel numbers should be odd and even in this order).
When the Pair Confirmation check box is on, the Channel Pairing window appears.
Note: You can pair only channels that are adjacent, odd-even (in this order) channels. Pressing
the [SEL] button for a non-adjacent channel will be ignored. You cannot create or cancel a
pair of vertical partners.
01V96 Version 2—Owner’s Manual
Pairing Input Channels
93
2 Move the cursor to the desired button in the Channel Pairing window, then
press [ENTER].
The following buttons are available in this window:
• CANCEL
Cancels the operation.
• CH x ➔ y
Copies the odd channel parameter values to the even channel.
• CH y ➔ x
Copies the even channel parameter values to the odd channel.
• RESET BOTH
Resets both channel parameters to the default settings (same as when Channel memory #01
is recalled).
Move the cursor to the desired button, then press [ENTER] to confirm the pair.
■ Pairing Input Channels Using the Display
1 Press the [PAIR/GROUP] button repeatedly until the Pair/Grup | Input page
appears.
1
2
The parameters on this page are described below:
A PAIR MODE
Determines how channels are paired.
B STEREO/MONO x2 buttons
These buttons turn pairs on or off.
2 Move the cursor to the PAIR MODE parameter field (1), then select the
HORIZONTAL or VERTICAL button.
The function of each mode is described below:
• HORIZONTAL.............This button pairs adjacent odd-even channels (default).
• VERTICAL ....................This button pairs counterpart channels on Layer 1 and Layer 2
that share the same physical fader (e.g., CH1 & CH17, CH16 &
CH32, etc.). This mode is useful when you wish to use one
fader to control both stereo channels.
01V96 Version 2—Owner’s Manual
7
Input Channels
Tip: Pressing and holding down the first [SEL] button of the paired channels and pressing
the second [SEL] button cancels the pair.
94
Chapter 7—Input Channels
When you switch the Pair Mode, the combinations of channel numbers displayed on the
page also change.
Note:
• When Pair mode is switched, only the channel numbers change. The mix parameters of the
paired partners do not change.
• For example, if you change Pair mode from Horizontal to Vertical, the Input Channel “2”
indication changes to Input Channel “17.” However, its parameters do not change. (If Channels 1 and 2 have been paired, switching the mode will pair Channels 1 and 17.)
3 Move the cursor to the desired channel’s MONOx2 button (2), then press
[ENTER].
The channels are paired.
4 To cancel a pair, move the cursor to the desired channel’s STEREO button,
then press [ENTER].
Tip: You can also create or cancel a pair of Output Channels in the same way on the Pair/Grup
| Output page (see page 105).
Naming Input Channels
By default, Input Channels are named CH1, CH2, etc. You can change these names if
desired. For example, it may be helpful for mixdown if you name a particular Input Channel with the type of musical instrument connected to the corresponding input jack.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | IN
Name page appears.
1
2
3
You can specify Short names in the center column (1) and Long (full) names in the right
column (2).
When the Name Input Auto Copy check box (3) is on, the first four characters of a
newly-entered Long name are automatically copied to the Short name. On the other hand,
a newly-entered Short name is automatically added to the beginning of the Long name.
You can reset all channel names to their default names by moving the cursor to the INITIALIZE button, then pressing [ENTER].
01V96 Version 2—Owner’s Manual
Naming Input Channels
95
2 Move the cursor to a name you wish to change, then press [ENTER].
The Title Edit window appears, enabling you to enter a name.
3 Edit the name, move the cursor to the OK button, then press [ENTER].
The new name is now effective.
Tip: The edited name is stored in the Input Patch library.
7
Input Channels
01V96 Version 2—Owner’s Manual
96
Chapter 7—Input Channels
01V96 Version 2—Owner’s Manual
Bus Outs
97
8 Bus Outs
This chapter describes how to adjust the 01V96’s Stereo Out and Bus Out 1–8 parameters.
About Stereo Out
The Stereo Out section receives Input Channel and Bus Out 1–8 signals, mixes them into
two channels, processes them using on-board EQ, compressor, etc., then routes them to the
STEREO OUT and 2TR OUT connectors. The following diagram illustrates the Stereo Out
signal flow.
(Gain Reduction) (Out Meter)
METER METER
STEREO L
STEREO R
COMP
INSERT
ATT
METER
INSERT
INSERT
ON LEVEL
BAL
OUTPUT
DELAY
4BAND
EQ
L
(-10dBV) [2TR OUT]
R
METER
DA
L
(+4dBu)
DA
R
[STEREO OUT]
Same as stereo master L
• INSERT
This section enables you to route the Stereo Out signals to external devices via the on-board
connectors or I/O card, or insert internal effects processors.
• ATT (Attenuator)
This section enables you to attenuate or amplify the level of signals to be input to the EQ.
The attenuator prevents post-EQ signals from clipping or corrects signal levels that are too
low.
• 4 BAND EQ (4-band equalizer)
This parametric EQ features four bands (HIGH, HIGH-MID, LOW-MID, and LOW).
• COMP (Compressor)
This dynamics processor can be used as compressor, expander, or limiter. The processor can
be located pre-EQ, pre-[STEREO] fader, or post-[STEREO] fader.
• ON (On/Off)
This button turns the Stereo Out on or off.
• LEVEL
The [STEREO] fader adjusts the Stereo Out output levels.
• Balance
This section enables you to adjust the level balance between the L and R channels of the Stereo Out.
• OUTPUT DELAY (Output delay)
This section delays the output signals. It is mainly used to fine-tune the signal timing.
01V96 Version 2—Owner’s Manual
Bus Outs
OUTPUT PATCH
8
98
Chapter 8—Bus Outs
• METER
This section enables you to switch the metering position of signal levels that are displayed
on the Meter page or by the stereo meter to the right of the screen. (See page 34 for more
information on selecting the metering position.)
Note: You can also patch the Stereo Out signals to other output connectors or the I/O card by
using the Patch | Out Patch pages.
Bus Out 1–8
The Bus Out 1–8 section mixes signals routed from Input Channels to the specified buses,
processes them using on-board EQ, compressor, etc., then routes them to the specified output connectors or I/O card.
The following diagram illustrates the Bus Out signal flow.
(Gain Reduction) (Out Meter)
METER METER
INSERT
ATT
METER
INSERT
BUS 1(...8)
OUTPUT
DELAY
4BAND
EQ
ON
PAN
•
•
•
•
•
•
•
•
METER
INSERT
ON LEVEL
LEVEL
BUS to STEREO
OUTPUT PATCH
STEREO L
STEREO R
BUS1
BUS2
BUS3
BUS4
BUS5
BUS6
BUS7
BUS8
COMP
INSERT
ATT (Attenuator)
4 BAND EQ (4-band equalizer)
COMP (Compressor)
ON (On/Off)
LEVEL
OUTPUT DELAY (Output delay)
METER
The parameters and sections listed above are identical to those for the Stereo Out. For more
information, refer to the explanation of the Stereo Out (see page 97).
• Bus to Stereo
Bus Out 1–8 signals are also routed to the Stereo Bus. In addition to the ON, LEVEL, and
other parameters, you can also set the Send Level, On/Off, Pan, and other parameters.
Tip:
• You can also pair adjacent odd-even buses for stereo operation (see page 105).
• By default, Slot channels 1–8 and 9–16 and ADAT OUT channels 1–8 are patched to the
Bus Out 1–8 outputs. However, you can change this patching on the Patch | Out Patch page
(see page 123).
01V96 Version 2—Owner’s Manual
Setting the Stereo Out and Bus Out 1–8 from the Display
99
Setting the Stereo Out and Bus Out 1–8 from the Display
To set the Stereo Out and Bus Out 1–8 parameters, you can either move the cursor to the
desired parameter on the display and change the value, or operate the desired button or
control on the top panel.
This section explains how to set the parameters on the display.
Tip: Refer to Chapter 10 “Input & Output Patching” on page 121 for more information on
how to set inserts.
Attenuating the Stereo Out and Bus Out
To attenuate the Stereo Out and Bus Out signals, press the DISPLAY ACCESS [EQ] button,
then press the [F4] button to display the EQ | Out Att page. On this page, you can attenuate
the Bus Out 1–8, Aux Out 1–8, and Stereo Out signals.
8
Bus Outs
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 83).
Delaying the Stereo Out and Bus Outs
To delay the Stereo Out and Bus Out 1–8 signals, press the [
repeatedly until the /INS/DLY | Out Dly page appears.
/INSERT/DELAY] button
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels, except that this page does not include the MIX/FB.GAIN parameters (see
page 80).
Tip: You can also display the Out Dly page by pressing the [ /INSERT/DELAY] button once,
then press the [SEL] button to select the Stereo Out or Bus Out 1–8.
01V96 Version 2—Owner’s Manual
100
Chapter 8—Bus Outs
Compressing the Stereo Out and Bus Outs
To set the Stereo Out and Bus Out 1–8 compressors, press the [DYNAMICS] button, then
the [F3] button to display the Dynamics | Comp Edit page, and use the [SEL] buttons to
select the Stereo Out or Bus Out 1–8.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 82).
EQ’ing the Stereo Out and Bus Outs
To set the EQ for the Stereo Out and Bus Out 1–8 EQ, press the DISPLAY ACCESS [EQ]
button, then press the [F1] button to display the EQ | EQ Edit page, and use the [SEL] buttons to select the Stereo Out or Bus Out 1–8.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 84). Note that the Stereo Out does not feature the STEREO LINK
parameter.
01V96 Version 2—Owner’s Manual
Setting the Stereo Out and Bus Out 1–8 from the Display
101
Routing Bus Out 1–8 Signals to the Stereo Bus.
You can patch Bus Out 1–8 signals to Outputs and Slots 1/2, as well as to the Stereo Bus. You
can adjust the level and pan settings of the signals routed to the Stereo Bus for each bus. This
is convenient when you wish to use Bus Outs (1–8) as a Group Bus.
To patch the Bus Out 1–8 signals to the Stereo Bus, press the DISPLAY ACCESS
[PAN/ROUTING] button repeatedly to display the Pan/Route | Bus to St page.
1
2
3
8
A TO ST PAN
These controls pan the Bus Out 1–8 signals between the left and right Stereo Out buses.
B TO ST ON/OFF
These buttons turn on and off the Bus Out 1–8 to the Stereo Bus routing.
C TO ST Faders
These faders set the Bus Out 1–8 to Stereo Bus levels.
01V96 Version 2—Owner’s Manual
Bus Outs
Move the cursor to the desired parameter you wish to change, then rotate the Parameter
wheel or press the [INC]/[DEC] buttons to modify the setting.
102
Chapter 8—Bus Outs
Viewing the Stereo Out and Bus Out Settings
You can view and adjust parameter settings for the currently-selected Stereo Out or Bus Out
on the View | Parameter and Fader pages.
■ Viewing the Compressor and EQ Settings
To display the View | Parameter page, use the corresponding [SEL] button to select the
desired bus, then press the DISPLAY ACCESS [VIEW] button, then press the [F1] button.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels, except for the following items:
• The Stereo Out and Bus Out 1–8 Parameter pages do not contain the Gate and Phase
parameters.
• The Stereo Out Parameter page does not contain the Pair parameter.
■ Viewing Faders and Other Parameters
To display the View | Fader page, use the corresponding [SEL] button to select the desired
bus, then press the DISPLAY ACCESS [VIEW] button, then press the [F2] button.
The Fader page layouts for Stereo Out and Bus Out 1–8 are slightly different.
• Stereo Out Fader page
1
2
3
A BAL
This control adjusts the level balance between the L and R channels of the Stereo Out.
B ON/OFF
This button turns the Stereo Out on or off, and links with the [ON] button in the STEREO section.
01V96 Version 2—Owner’s Manual
Setting the Stereo Out and Bus Out 1–8 from the Display
103
C Fader
This fader adjusts the Stereo Out output levels, and links with the [STEREO] fader. The
fader knob is highlighted when the fader is set to 0.0 dB.
• Bus Out (1–8) Fader page
345
1
2
8
This button turns the currently-selected Bus Out (1–8) on or off, and links with the
[ON] (9–16) button in the Master layer.
B Fader
This fader sets the currently-selected Bus Out (1–8) level, and links with the fader (9–16)
in the Master layer. The fader knob is highlighted when the fader is set to 0.0 dB.
C TO ST PAN
This control sets the Bus Out to Stereo Out Pan position for the currently-selected Bus
Out (1–8).
D TO ST ON/OFF
This button turns on or off the Bus Out to Stereo Out signal for the currently-selected
Bus Out (1–8).
E TO ST Fader
This fader sets the Bus Out to Stereo Out signal level for the currently-selected Bus Out
(1–8).
Tip: The TO ST PAN, ON/OFF, and TO ST Fader parameters also appear on the Pan/Route
| Bus to St page.
01V96 Version 2—Owner’s Manual
Bus Outs
A ON/OFF
104
Chapter 8—Bus Outs
Setting the Stereo Out and Bus Out 1–8 from the
Control Surface
You can use the faders, [SEL] buttons, and various buttons and controls in the SELECTED
CHANNEL section on the top panel to directly control certain parameters for the Stereo
Out and Bus Out 1–8.
Setting the Levels
Move the [STEREO] fader to adjust the Stereo Out levels. Press the [ON] button in the STEREO section to turn the Stereo Out on or off.
To set Bus Out 1–8 levels, press the [MASTER] button in the LAYER section to select the
Master layer, then move faders 9–16. At this time, you can turn Bus Out 1–8 on or off using
the [ON] 9–16 buttons.
EQ’ing and Balancing the Stereo Out and Bus Outs
1 Press the [SEL] button of the bus to which you want to apply EQ or set the
level balance.
2 To adjust the EQ of the currently-selected bus, select the desired band by
pressing one of the following buttons in the SELECTED CHANNEL section:
• [HIGH] button ............ HIGH band
• [H-MID] button .......... HIGH-MID band
• [L-MID] button ........... LOW-MID band
• [LOW] button .............. LOW band
3 Use the [Q], [FREQUENCY], and [GAIN] controls to adjust the Q, frequency,
and gain of the band selected in Step 2.
See page 84 for more information on EQ.
4 To adjust the Stereo Out Balance parameter, use the [PAN] control in the
SELECTED CHANNEL section.
Note: If you select Aux Out 1–8 or Bus Out 1–8, the [PAN] control is disabled.
01V96 Version 2—Owner’s Manual
Pairing Buses or Aux Sends
105
Pairing Buses or Aux Sends
You can pair adjacent odd-even (in this order) buses or Aux Sends for stereo operation.
Paired bus and Aux Send linked parameters and non-linked parameters (that are available
for independent controls) are listed below:
Linked parameters
Non-linked parameters
[SEL] buttons
Output Patching
Fader
Insert Patching
Channel on/off
Delay on/off
Insert on/off
Delay time**
Solo on/off
Bus to Stereo Pan*
Comp settings
Attenuators***
Comp insert position
EQ settings
Fader group
Mute group
Fade time
** You can set this parameter for each channel independently if the GANG button is turned off on the
/INS/DLY |
DLY page.
*** You can set this parameter for each channel independently on the EQ | ATT page, but the paired channel settings
are linked on the EQ | Edit and View pages.
Recall safe
8
Bus to Stereo on/off*
Bus to Stereo fader*
1 Press the DISPLAY ACCESS [PAIR/GROUP] button repeatedly until the
Pair/Grup | Output page appears.
1
2
The parameters on this page are described below.
A STEREO/MONOx2
These buttons turn Bus or Aux Send pairs on or off.
B F.S
This button determines whether Aux Sends follow the Input Channel Surround Pan
when the 01V96 is in any Surround mode other than “Stereo.” When this button is
turned on, Aux Sends follow the Input Channel Surround Pan. This is useful for feeding
Surround signals to external Surround effects processors.
2 Move the cursor to the MONOx2 button for the desired Bus or Aux Send,
then press [ENTER].
The buses or Aux Sends are paired.
3 To cancel a pair, move the cursor to the STEREO button for the desired Bus
or Aux Send, then press [ENTER].
01V96 Version 2—Owner’s Manual
Bus Outs
Parameters marked with an asterisk * are available only for Bus Outs.
106
Chapter 8—Bus Outs
Attenuating Output Signals
To attenuate the 01V96’s output signals, display the EQ | Out Att page and adjust the Stereo
Out and Bus Out 1–8 attenuators individually.
If necessary, you can also select Output and I/O card channels and specify the amount of
attenuation. This technique is convenient when you want to attenuate output signals
quickly, regardless of the source signal patching.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Output Att page appears.
1
2
2 Move the cursor in the left column (1), then scroll the list up or down using
the Parameter wheel to select the desired output or slot channel for which
you want to adjust attenuation.
The following outputs and slot channels can be selected:
• STEREO OUT L/R ...............................STEREO OUT L & R channels
• MONITOR OUT L/R ..........................MONITOR OUT L & R channels
• OMNI OUT 1–4 ...................................OMNI OUT connectors 1–4
• SLOT OUT 1–1 through 1–16 ...........Slot channels 1–16
• ADAT OUT 1–8....................................ADAT OUT channels 1–8
• 2TR OUT DIGITAL L/R .....................2TR OUT DIGITAL L & R channels
3 Move the cursor to the parameter value in the right column (2), then rotate
the Parameter wheel or press the [INC]/[DEC] buttons to set the amount of
attenuation.
The amount of attenuation can be set from 0 dB to –9 dB.
Tip: To reset the attenuation amount of all Output Channels to 0 dB, move the cursor to the
INITIALIZE button, then press [ENTER].
01V96 Version 2—Owner’s Manual
Naming the Stereo Out and Bus Outs
107
Naming the Stereo Out and Bus Outs
You can change the default Bus names (BUS1, AUX4, STEREO, etc.). It may be convenient
to name the buses “Monitor Out” or “Effect Send,” for example, so that you can easily identify the signal type.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | Out
Name page appears.
1
2
3
8
2 Move the cursor to a name you wish to change, then press [ENTER].
The Title Edit window appears, which enables you to edit the name.
3 Edit the name, move the cursor to the OK button, then press [ENTER].
The new name is now effective.
Tip: The edited name is stored in the Output Patch library.
01V96 Version 2—Owner’s Manual
Bus Outs
You can specify Short names in the center column (1) and Long (full) names in the right
column (2).
When the Name Input Auto Copy check box (3) is on, the first four characters of a
newly-entered Long name are automatically copied to the Short name. On the other hand,
a newly-entered Short name is automatically added to the beginning of the Long name.
You can reset all bus names to their default names by moving the cursor to the INITIALIZE
button, then pressing [ENTER].
108
Chapter 8—Bus Outs
01V96 Version 2—Owner’s Manual
Aux Outs
109
9 Aux Outs
This chapter describes how to control Aux Out 1–8.
Aux Out 1–8
The Aux Out 1–8 section mixes signals routed from the Input Channels to the corresponding Aux Sends, processes them using on-board EQ, compressor, etc., then routes them to
the specified internal effects processors, output connectors or I/O card connectors.
The 01V96 features eight Aux Sends, which can be used to send signals to the internal and
external effects processors and monitors.
The following diagram illustrates the Aux Out 1–8 signal flow.
(Gain Reduction) (Out Meter)
METER METER
INSERT
ATT
4BAND
EQ
INSERT
METER
INSERT
ON LEVEL
OUTPUT
DELAY
AUX 1(...8)
INSERT
ATT (Attenuator)
4 BAND EQ (4-band equalizer)
COMP (Compressor)
ON (On/Off)
LEVEL
OUTPUT DELAY (Output delay)
METER
These parameters are the same as the Stereo Out and Bus Out 1–8 (see page 97).
Tip: You can also pair adjacent odd-even Aux Sends (in this order) for stereo Aux operation.
Note: With the default setting, Aux Out 1–4 are patched to OMNI OUT connectors 1–4 and
to internal Effects processors 1–4. However, you can change this patching on the Patch | Output
page.
01V96 Version 2—Owner’s Manual
9
Aux Outs
•
•
•
•
•
•
•
•
METER
OUTPUT PATCH
AUX 1
AUX 8
COMP
110
Chapter 9—Aux Outs
Setting Aux Out 1–8 from the Display
To set Aux Out 1–8 parameters, you can either move the cursor to the desired parameter on
the screen and change the value, or operate the desired button or control on the top panel.
This section explains how to set the parameters on the screen.
Tip: Refer to Chapter 10 “Input & Output Patching” on page 121 for more information on
how to set inserts.
Attenuating Aux Outs
To attenuate Aux Out 1–8 signals, press the [EQ] button, then press the [F4] button to display the EQ | Out Att page.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 83).
Delaying Aux Outs
To delay Aux Out 1–8 signals, press the DISPLAY ACCESS [
repeatedly until the /INS/DLY | Out Dly page appears.
/INSERT/DELAY] button
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels, except that this page does not include the MIX/FB.GAIN parameters (see
page 80).
Tip: You can also display the Out Dly page if you select the desired Aux Out (1–8) by pressing
the corresponding [SEL] button while the DLY-related parameters are indicated on the page.
01V96 Version 2—Owner’s Manual
Setting Aux Out 1–8 from the Display
111
Comp settings
To set the Aux Out 1–8 compressors, press the DISPLAY ACCESS [DYNAMICS] button,
then press the [F3] button to display the Dynamics | Comp Edit page, then select the desired
Aux Out 1–8 by using the corresponding [SEL] buttons.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 82).
To set the EQ for Aux Out 1–8, press the DISPLAY ACCESS [EQ] button, then press the [F1]
button to display the EQ | EQ Edit page, then use the [SEL] buttons to select Aux Out 1–8.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 84).
01V96 Version 2—Owner’s Manual
Aux Outs
EQ settings
9
112
Chapter 9—Aux Outs
Viewing Aux Out Settings
You can view and adjust the parameter settings for the currently-selected Aux Out on the
View | Parameter and Fader pages.
■ Viewing the Compressor and EQ Settings
To display the View | Parameter page, use the corresponding [SEL] button to select the
desired Aux Out (1–8), then press the DISPLAY ACCESS [VIEW] button, then press the
[F1] button.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels, except that this page does not include the Gate and Phase parameters (see
page 87).
■ Viewing Faders and On/Off Parameters
To display the View | Fader page, use the corresponding [SEL] button to select the desired
Aux Out (1–8), then press the DISPLAY ACCESS [VIEW] button, then press the [F2] button.
• ON/OFF ........................ This button turns the currently-selected Aux Out (1–8) on or
off. It links with the corresponding [ON] (1–8) button in the
Master layer.
• Fader.............................. This fader sets the currently-selected Aux Out (1–8) level. It
links with the corresponding fader (1–8) in the Master layer.
The fader knob is highlighted when the fader is set to 0.0 dB.
01V96 Version 2—Owner’s Manual
Setting Aux Out 1–8 from the Control Surface
113
Setting Aux Out 1–8 from the Control Surface
You can use the faders, [SEL] buttons, and various buttons and controls in the SELECTED
CHANNEL section on the top panel to directly control certain parameters for Aux Out 1–8.
Setting Levels
To set Aux Out 1–8 levels, press the [MASTER] button in the LAYER section to select the
Master layer, then move faders 1–8. At this time, you can turn Aux Out 1–8 on or off using
the corresponding [ON] 1–8 buttons.
EQ settings
To control Aux Out 1–8 EQ parameters, select the desired Aux Out (1–8) using the corresponding [SEL] button or fader, then use the buttons and controls in the SELECTED
CHANNEL section. The parameters on this page (and the procedure for setting them) are
the same as for Input Channels (see page 83).
Setting Aux Send Levels
You can adjust the level of signals routed from Input Channels to the corresponding Aux
Out (1–8).
You can view multiple channels’ Aux Send levels on the screen and adjust them individually.
1 Press the FADER MODE [AUX 1]–[AUX 8] buttons to select the Aux.
2 Make sure that the 01V96 displays the Aux | Send page.
This page enables you to adjust the level of the signals routed from each Input Channel to
the Aux selected in Step 1.
If the Send page is not displayed, repeatedly press the button that you pressed in Step 1 until
the Send page appears.
• Aux Send rotary controls
These controls adjust the Aux Send level of the Input Channels. The current numeric levels
appear below the rotary controls.
• PRE/POST
These buttons enable you to specify the Aux signal source points. The PRE buttons send
pre-fader signals, and the POST buttons send post-fader signals.
01V96 Version 2—Owner’s Manual
Aux Outs
Setting Send Levels from the Display
9
114
Chapter 9—Aux Outs
• MODE
Aux Sends have two operating modes that determine how signals are sent: Fixed (Aux Send
levels are fixed); and Variable (Aux Send levels are variable).
• GLOBAL
The GLOBAL PRE and POST buttons enable you to set all Input Channels for the selected
Aux to pre-fader or post-fader simultaneously.
• PRE POINT
The PRE POINT PRE ON and POST ON buttons enable you to set the pre-fader channels
to pre-on (before the [ON] button) or post-on (after the [ON] button).
Note: In Fixed mode, Aux Send ON/OFF buttons appear instead of the Aux Send rotary controls, PRE/POST buttons, GLOBAL PRE/POST buttons, and PRE POINT PRE ON/POST
ON. These ON/OFF buttons turn on or off each Input Channel for the currently-selected Aux
Send.
3 Move the cursor to the FIXED or VARIABLE button in the MODE section for
the currently-selected Aux Send to select a mode.
• Fixed Mode
In this mode, Aux Send levels are fixed at nominal (0.0 dB). Also, channel ON/OFF buttons
appear instead of the Send level rotary controls and PRE/POST buttons.
01V96 Version 2—Owner’s Manual
Setting Aux Send Levels
115
• Variable Mode
In this mode, Aux Send levels are variable and the signal source point can be either pre-fader
or post-fader. Channel Send level rotary controls and PRE/POST buttons appear on the
screen.
Tip: You can select Variable or Fixed mode individually for each of the eight Aux.
4 If you switched to Fixed mode in Step 3, the ON/OFF buttons turn each Input
Channel on or off for the currently-selected Aux Send.
Note: In Fixed mode, the Aux On/Off parameters for paired Input Channels are not linked
to each other.
01V96 Version 2—Owner’s Manual
9
Aux Outs
Note:
• In Fixed mode, all ON/OFF buttons are turned OFF.
• When you switch to Variable mode, the signal source points are set to post-fader (PRE/POST
buttons are set to POST), and Send level rotary controls are reset to –∞.
116
Chapter 9—Aux Outs
5 If you switched to Variable mode in Step 3, the PRE/POST buttons and Send
level rotary controls enable you to adjust the signal source points and Send
levels.
You can turn each Input Channel on or off for the currently-selected Aux Send even in Variable mode. To do this, move the cursor to the desired Send level control, then press
[ENTER]. (The rotary controls for Off channels are grayed out.)
Tip:
• In Variable mode, Aux Send levels, Aux On/Off, and Pre/Post parameters for paired Input
Channels are linked to each other.
• GLOBAL PRE/POST buttons enable you to set all Input Channels simultaneously (including those not displayed on the current page) to pre-fader or post-fader.
Note:
• Do not raise the level of the Aux Sends (patched to the effects processor) on the effects return
channels.
• For example, by default, Aux 1 is routed to the input of the internal Effects processor 1, and
L and R of ST IN Channel 1 are patched to the processor's output. Under these conditions,
if you raise the level of the send signals from ST IN Channel 1 to Aux 1, the signals are
returned to ST IN Channel 1, creating a signal loop and possibly damaging your speakers.
01V96 Version 2—Owner’s Manual
Viewing Aux Send Settings for Multiple Channels
117
Viewing Aux Send Settings for Multiple Channels
You can view and set parameters for all Aux Send 1–8, including setting levels and Pre/Post
parameters.
This is convenient when you wish to visually check all Aux Send settings or simultaneously
adjust the levels of certain channels routed to Aux 1–8.
1 Press one of the FADER MODE [AUX 1]–[AUX 8] buttons repeatedly until the
page listed below that contains the desired channels appears.
- View1-16 page
This page displays the Aux Send levels of Input Channels 1–16.
- View17-STI page
This page displays the Aux Send levels of Input Channels 17–32 and ST IN Channels
1–4.
These pages display the source Input channels and the corresponding Aux Sends in a
matrix. The parameters on these two pages (and the procedure for setting them) are the
same.
1
9
Aux Outs
2
3
A DISPLAY
Use the following buttons to display the desired parameters.
• LEVEL............................Select the LEVEL button to display Send level bar graphs for
Input Channels routed to Aux 1–8.
• PRE/POST.....................Select the PRE/POST button to display signal source points for
Input Channels routed to Aux 1–8.
B FIX/VARI
These buttons indicate the Aux mode (Fixed or Variable) for Aux Out 1–8 and are only
for display purposes.
C LEVEL
This field displays in dB the level of the Aux Send currently-selected by the cursor.
2 Move the cursor to either the DISPLAY LEVEL or PRE/POST button, then press
[ENTER] to display the Level or Pre/Post parameters.
01V96 Version 2—Owner’s Manual
118
Chapter 9—Aux Outs
3 If you selected the PRE/POST button in Step 2, move the cursor to the desired
Input Channel and Aux intersection, then press the [ENTER] button to
change the signal source point.
Note: You can switch between Pre and Post only for Aux Sends that are set to Variable mode.
The “FIX” indication appears for Aux Sends that are set to Fixed mode, and you cannot switch
Pre/Post.
4 If you selected the LEVEL button in Step 2, move the cursor to the desired
Input Channel and Aux intersection, then edit the Send level or turn the currently-selected AUX Send on or off.
Rotate the Parameter wheel or press the [INC]/[DEC] buttons to set the Send level, then
press the [ENTER] button to turn the currently-selected Aux Send on or off.
One of the following indicators appears, depending on the current Aux mode.
• Aux Sends in Fixed mode ...................A “FIX” indicator appears for On Aux Sends, and
a dot “ . ” appears for Off Aux Sends.
• Aux Sends in Variable mode..............The current Send levels are displayed by the bar
graphs. If the level is set to nominal (0.0 dB), “N”
appears in the bar. The bars for Aux Sends that
are turned off are highlighted.
01V96 Version 2—Owner’s Manual
Panning Aux Sends
119
Panning Aux Sends
You can pair adjacent odd-even (in this order) Aux Sends for stereo operation. This enables
you to pan signals from Input Channels to paired Aux Sends.
1 Pair the desired two Aux Sends. (See page 105 for more information on pairing channels.)
2 Use the FADER MODE [AUX 1]–[AUX 8] buttons to select one of the paired
Aux Sends.
3 Repeatedly press the button you pressed in Step 2 to display the Aux | Pan
page.
2
3
1
9
Aux Outs
A Aux pan controls
These controls adjust the pan setting of signals routed from Input Channels to paired
Aux buses.
B MODE
The MODE parameter determines how paired Input Channels are panned.
C INPUT PAN LINK
When this parameter is turned on, Aux Sends follow the Input Channel Pan.
4 Move the cursor to the Aux pan control of the desired Input Channel, the
rotate the Parameter wheel to set the pan value.
5 If necessary, move the cursor to the MODE parameter box, then rotate the
Parameter wheel to select INDIVIDUAL, GANG, or INV GANG, then press
[ENTER].
If the INPUT PAN LINK ON/OFF button is turned off, this Mode setting is independent of
the Mode parameter on the Pan page. (See page 85 for more information on Mode
options.)
6 To link the Input Channel Pan setting with the Aux Send Pan setting, move
the cursor to the INPUT PAN LINK ON/OFF button, then press [ENTER].
The pan positions on the Pan page are copied to the Aux pan setting, and the pan controls
on both pages are linked.
Tip:
• If paired Aux Sends are in Variable mode, the Aux Send levels, Aux On/Off, and Pre/Post
parameters for paired Input Channels are linked to each other.
• If paired Aux Sends are in Fixed mode, the Aux On/Off parameters for paired Input Channels are not linked to each other.
01V96 Version 2—Owner’s Manual
120
Chapter 9—Aux Outs
Copying Channel Fader Positions to Aux Sends
While Aux Sends are in Variable mode, you can copy all Input Channel fader positions on
one layer to the corresponding Aux Sends.
This is convenient when you wish to send to the musicians monitor signals that have the
same balance setting as the Stereo Out signals.
1 Press and hold down the copy source layer (LAYER [1–16] or [17–32]) button.
Note: If you release the button in the LAYER section before you proceed to Step 2, you will be
unable to complete the Copy operation.
2 Press one of the FADER MODE [AUX 1]–[AUX 8] buttons to select the desired
Aux Send copy destination.
The confirmation window for the Copy operation appears.
3 To execute the Copy operation, move the cursor to the YES button, then
press [ENTER].
To cancel the Copy operation, move the cursor to the NO button, then press [ENTER].
Tip: If the copy destination Input Channel has been paired with a vertical partner in another
Layer, the fader position will be copied to the partner’s Aux Send.
01V96 Version 2—Owner’s Manual
Input & Output Patching
121
10 Input & Output Patching
This chapter describes how to patch (assign) signal paths within the 01V96 to its inputs,
outputs, and slot channels
Input Patching
Signals input at INPUT connectors 1–16, ADAT IN connector, 2TR IN DIGITAL connectors, and Slot I/O card are patched to Input Channels for use.
Patch example:
Input Patching
Input Channel 1
INPUT connector 2
Input Channel 2
INPUT connector 3
Input Channel 3
INPUT connector 4
Input Channel 4
INPUT connector 5
Input Channel 5
INPUT connector 6
Input Channel 6
INPUT connector 7
Input Channel 7
INPUT connector 8
Input Channel 8
By default, the Input Channels are patched as follows:
Input Channels
Input connectors and Slot channels
1–16
INPUT connectors 1–16
17–24
ADAT IN Input Channels 1–8
25–32
Slot Channels 1–8
ST IN Channels 1–4
Internal Effects Processor 1–4 Outputs 1–2
You can change these patches, if you desire.
01V96 Version 2—Owner’s Manual
10
Input & Output Patching
INPUT connector 1
122
Chapter 10—Input & Output Patching
Input Patching
Follow the steps below to change the Input Patch.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | In
Patch page appears.
1
Inputs, ADAT IN channels, and slot channels that are currently assigned to Input Channels
are shown in the parameter boxes (1) below the channel numbers. The parameter indicators are explained below:
Parameter value
Description
–
No assignment
AD1–AD16
INPUT connectors 1–16
ADAT1–ADAT8
ADAT IN Input Channels 1–8
SL-01–SL-16
Slot Channels 1–16
FX1-1 & FX1-2
Outputs 1 & 2 of Internal Effects Processor 1
FX2-1 & FX2-2
Outputs 1 & 2 of Internal Effects Processor 2
FX3-1 & FX3-2
Outputs 1 & 2 of Internal Effects Processor 3
FX4-1 & FX4-2
Outputs 1 & 2 of Internal Effects Processor 4
2TD-L & 2TD-R
2TR DIGITAL IN (L/R)
2 Move the cursor to an input patch parameter you wish to change, then
rotate the Parameter wheel or press the [INC]/[DEC] buttons to modify the
patching.
The long name of the currently-selected channel is
1
indicated in the upper-right corner of the screen (1).
2
Below the channel name is the long name of the
selected input channel (2). (See page 94 and 229 for
information on changing channel names.)
3 Press [ENTER] to confirm the change.
Tip:
• You can patch an input signal to multiple Input Channels.
• You can store the Input Patch settings to the Input Patch library. Refer to Chapter 16 for more
information.
01V96 Version 2—Owner’s Manual
Output Patching
123
Output Patching
The 01V96’s Stereo Out, Bus Out 1–8, Aux Out 1–8 signals can be patched to any outputs,
ADAT OUT output channels, and slot output channels.
Patch example:
Output Patching
Aux Out 1
OMNI Out connector 1
Aux Out 2
OMNI Out connector 2
Aux Out 3
OMNI Out connector 3
Aux Out 4
OMNI Out connector 4
Aux Out 5
OMNI Out connector 1
Aux Out 6
OMNI Out connector 2
Aux Out 7
OMNI Out connector 3
Aux Out 8
OMNI Out connector 4
By default, the following signal paths are patched to outputs, ADAT OUT output channels,
and slot output channels:
Signal flow
Bus Outs 1–8
Slot Channels 1–8
Bus Outs 1–8
Slot Channels 9–16
Bus Outs 1–8
OMNI OUT connectors 1–4
Aux Outs 1–4
2TR OUT DIGITAL (L)
Stereo Out L
2TR OUT DIGITAL (R)
Stereo Out R
Tip:
• You can patch a signal to multiple outputs.
• You can store the Output Patch settings to the Output Patch library. Refer to Chapter 16 for
more information.
You can change these patches, if you desire. The procedure for patching signals to output
varies depending on the output connectors and slots.
01V96 Version 2—Owner’s Manual
Input & Output Patching
Output connectors and slot channels
ADAT OUT output channels 1–8
10
124
Chapter 10—Input & Output Patching
Changing the Signal Path to the ADAT OUT Connector, Slot,
or OMNI OUT connectors
Follow the steps below to change the signal path patched to the ADAT OUT connector, the
optional mini-YGDAI card installed in the slot, or the OMNI OUT connectors.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | Out
Patch page appears.
Each parameter box displays the currently-patched signal path.
1
2
3
A SLOT 1-16
These parameter boxes set the routing of Slot Channel 1-16 signals.
B ADAT 1-8
These parameter boxes set the routing of ADAT OUT connector output channel 1-8 signals.
C OMNI 1-4
These parameter boxes set the routing of OMNI OUT connector 1-4 signals.
The parameter indicators are explained below:
Parameter value
Description
–
No assignment
BUS1–BUS8
Bus Out 1–8 signal
AUX1–AUX8
Aux Out 1–8 signal
ST L/R
Stereo Out signal
INS CH1–INS CH32
Input Channel 1–32 Insert Out
INS BUS1–INS BUS8
Bus Out 1–8 Insert Out
INS AUX1–INS AUX8
Aux Out 1–8 Insert Out
INS ST-L/ST-R
Stereo Out Insert Out
CAS BUS1–BUS8
Bus 1–8 Cascade Outs
CAS AUX1–AUX8
Aux Bus 1–8 Cascade Outs
CAS ST-L/ST-R
Stereo Bus Cascade Outs
CASSOLOL/CASSOLOR
Solo Bus Cascade Outs
2 Move the cursor to a patch parameter you wish to change, then rotate the
Parameter wheel or press the [INC]/[DEC] buttons to modify the patching.
3 Press [ENTER] to confirm the change.
Tip: You can store the Output Patch settings to the Output Patch library. Refer to Chapter 16
for more information.
01V96 Version 2—Owner’s Manual
Patching Direct Outs
125
Patching the 2TR Digital Outputs
Follow the steps below to change the signal path patched to the 2TR OUT DIGITAL connector.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | 2TR
Out page appears.
Signals assigned on the Out Patch page can also be assigned on this page.
2 Move the cursor to a patch parameter you wish to change, then rotate the
Parameter wheel or press the [INC]/[DEC] buttons to modify the patching.
3 Press [ENTER] to confirm the change.
Input Channel 1–32 signals can be directly patched to any outputs or slot outputs, as well
as Bus Out 1–8 and Stereo Out. This patching is convenient when you wish to record each
Input Channel signal to an individual track on a connected recorder.
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | Direct
Out page appears.
1
2
The parameters on this page are described below.
A 1–32
These boxes indicate the Direct Out destination (outputs, ADAT OUT output channels,
and slot output channels) for Input Channels 1–32.
B DIRECT OUT
Determines the Direct Out signal source position from the following three options:
01V96 Version 2—Owner’s Manual
Input & Output Patching
Patching Direct Outs
10
126
Chapter 10—Input & Output Patching
• PRE EQ.......................... Immediately before Input Channel EQ
• PRE FADER .................. Immediately before Input Channel fader
• POST FADER ............... Immediately after Input Channel fader
2 Move the cursor to a patch parameter (1–32) you want to change, then
rotate the Parameter wheel or press the [INC]/[DEC] buttons to select the
destination.
If necessary, specify the signal source position using the DIRECT OUT parameter.
3 Press [ENTER] to confirm the change.
Note: If you select a destination that is already used by an Output Patch setting and turn on
the Direct Out, the Output Patch setting will be disabled. To restore the Output Patch setting,
select another Direct Out destination or turn off the Direct Out.
4 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until one of
the following pages containing the channels you want to patch to the Direct
Out appears.
• Rout1-16 page .............. This page enables you to change the Input Channel 1–16 routings.
• Rout17-STI page.......... This page enables you to change the Input Channels 17–32 and
ST IN Channel 1–4 routings.
Tip: Refer to page 86 for more information on these pages.
5 Move the cursor to the D button for the channel you want to patch to the
Direct Out, then press [ENTER].
The Direct Out patching is now effective, and the signals are routed to the assigned outputs,
ADAT OUT channels, or slot output channels.
01V96 Version 2—Owner’s Manual
Insert Patching
127
Insert Patching
The 01V96’s Input Channels and Output Channels (Stereo Out, Bus Out 1–8, Aux Out 1–8)
feature independent Insert Ins and Outs. Inputs, outputs, ADAT connector channels, slot
channels, and internal effects processor inputs and outputs can be patched to the Output
Channel Insert Ins and Outs. In this way, you can send the signals to external effects processors for processing, or insert internal effects.
Individual Insert Patching
You can patch the 01V96’s inputs, outputs, ADAT connector channels, slot channels, and
effects processor inputs and outputs to the Insert Ins and Outs. The same procedure applies
to both Input Channels and Output Channels.
Effects
Input
Output connector
Insert Out
Output
Input connector
10
Insert In
1 Press the [SEL] button of an Input Channel or Output Channel for Insert
patching.
2 Press the [ /INSERT/DELAY] button repeatedly until the
page appears.
/INS/DLY | Insert
1
2
3
This page contains the following parameters:
A POSITION
This parameter determines the insert position of the Insert patch or compressor. The
insert position is indicated by highlighted COMP or INSERT buttons.
01V96 Version 2—Owner’s Manual
Input & Output Patching
Channel
128
Chapter 10—Input & Output Patching
B INSERT section
• ON/OFF ........................ This button turns the Insert on or off.
• OUT ............................... This parameter enables you to select outputs, ADAT OUT
channels, slot output channels, or internal effects inputs as the
Insert Out destination.
• IN ................................... This parameter enables you to select inputs, ADAT IN channels, slot input channels, or internal effects outputs as the Insert
In source.
C COMP section
• ON/OFF ........................ This button turns the compressor on or off.
• ORDER.......................... This parameter determines the order of Insert patch and compressor when they are inserted at the same signal path point.
With the “COMP → INS” setting, signals pass through the
compressor first, then the Insert. With the “INS → COMP” setting, signals pass through the Insert first, then the compressor.
3 Move the cursor to the OUT parameter box, then rotate the Parameter wheel
or press the [INC]/[DEC] buttons to select the desired outputs, slot channels,
or internal effects inputs to be patched to Insert Out.
The parameter indicators are explained below:
Parameter values
Description
–
No assignment
ADAT 1–ADAT 8
ADAT OUT Output Channels 1–8
SL-01–SL-16
Slot Channels 1–16
OMNI1–OMNI4
OMNI OUT connectors 1–4
2TD-L/2TD-R
2TR OUT DIGITAL (L/R)
FX1-1/FX1-2
Inputs 1 & 2 of Internal Effects Processor 1
FX2-1/FX2-2
Inputs 1 & 2 of Internal Effects Processor 2
FX3-1/FX3-2
Inputs 1 & 2 of Internal Effects Processor 3
FX4-1/FX4-2
Inputs 1 & 2 of Internal Effects Processor 4
4 Press [ENTER] to confirm the change.
If you move the cursor to another parameter box or display another page before you press
the [ENTER] button, all settings on this page will be cancelled.
5 Move the cursor to the desired IN parameter box, then rotate the Parameter
wheel or press the [INC]/[DEC] buttons to select the inputs, ADAT IN channels, or slot input channels to be patched to the Insert In.
Refer to the explanation regarding the Input Patch for more information on the parameter
values (see page 122).
6 Press [ENTER] to confirm the change.
Tip: Move the cursor to an empty OUT or IN parameter box and press the [ENTER] button.
The Patch Select window appears. Rotate the Parameter wheel or press the cursor buttons to
select an item to be patched, then press [ENTER]. Move the cursor to the YES button, then
press [ENTER]. The selected item is now patched.
7 To enable the specified Insert patch, move the cursor to the ON/OFF button
in the INSERT section, and press [ENTER] to turn it on or off.
01V96 Version 2—Owner’s Manual
Insert Patching
129
Viewing and Changing Insert In Patch
You can view and also change the items patched to the Insert Ins of all Input Channels (or
all Output Channels). This is useful when you wish to find out if multiple channels have the
same patch.
1 To view the Input Channels’ Insert Ins, press the [PATCH] button repeatedly
until the Patch | Input Ins page appears.
This page displays Input Channels 1–32 Insert In Patches.
2 Move the cursor to a channel patch parameter box you wish to change, then
rotate the Parameter wheel or press the [INC]/[DEC] buttons to modify the
patching.
4 To view the Output Channels’ Insert Ins, press the [PATCH] button repeatedly
until the Patch | Output Ins page appears.
5 Move the cursor to a channel patch parameter box you wish to change, then
rotate the Parameter wheel or press the [INC]/[DEC] buttons to modify the
patching.
6 Press [ENTER] to confirm the change.
01V96 Version 2—Owner’s Manual
Input & Output Patching
3 Press [ENTER] to confirm the change.
10
130
Chapter 10—Input & Output Patching
01V96 Version 2—Owner’s Manual
Monitoring
131
11 Monitoring
This chapter explains how to set up monitoring and use the Solo function on the 01V96.
Monitor
SOLO L
SOLO R
SOLO TRIM
SOLO L
SOLO R
[2TR IN]
L
RCA R
SOLO LOGIC
OUTPUT SOLO
BUS1-8
AUX1-8
8
8
MONITOR
/2TR IN
MONITOR TRIM
MONO
STEREO L
STEREO R
The 01V96 features the stereo signal path to feed the monitors. The monitoring signal
source is patched to MONITOR OUT connectors L & R and the PHONES connector.
The following diagram illustrates the monitoring signal flow.
MONITOR OUT
LEVEL
DA
L
[MONITOR OUT]
DA
R
PHONES
LEVEL
[PHONES]
• SOLO bus
This special bus routes soloed Input Channels to the Monitor outputs, bypassing Bus 1–8
and the Stereo Bus.
11
• OUTPUT SOLO
This section routes soloed Output Channels (Aux Out 1–8, Bus Out 1–8) to the Monitor
outputs.
Monitoring
Note: Input and Output Channels cannot be solo-monitored simultaneously. The solo function for the most-recently soloed channels is enabled.
• MONITOR TRIM
This section adjusts the monitoring signal level in the digital domain.
• MONITOR OUT LEVEL
Use the MONITOR [MONITOR OUT] control on the top panel to adjust the monitoring
signal level in the analog domain.
• MONITOR/2TR IN
As a monitoring signal, you can select either the 01V96 internal signals or 2TR IN digital
inputs.
• PHONES
The Monitor signal is also fed to the PHONES jack. You can set the level independently.
01V96 Version 2—Owner’s Manual
132
Chapter 11—Monitoring
Monitor and Solo Setup
For monitoring and solo setup, press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the DIO/Setup | Monitor page appears.
2
3
4
1
5
6
7
8
9
This page contains the following parameters:
A SOLO
This parameter turns the Solo function on or off. By default, it is set to Enabled.
B MODE
This parameter determines how the Solo function works. There are two options. The
setting affects only Input Channels.
• RECORDING............... In Recording Solo mode, soloed Input Channel signals are fed
to the Solo bus and output via the Monitor outputs. Other
buses (Stereo bus and Bus 1–8) are unaffected by this mode.
• MIXDOWN.................. In Mixdown Solo mode, soloed Input Channel signals are fed
to the Stereo bus and output via the Monitor outputs. Unsoloed Input Channels are not fed to the Stereo bus while the Solo
function is enabled.
Tip:
• Recording Solo mode is convenient when you wish to monitor certain Input Channels while
recording, since the Stereo bus and Bus 1–8 signals are unaffected.
• Mixdown Solo mode is useful when you wish to mute unsoloed Input Channels and feed
soloed Input Channel signals to the Stereo bus during mixdown.
C SEL MODE
This parameter determines how the Input Channels will be soloed when you press the
[SOLO] button of each Channel. There are two options.
• MIX SOLO.................... In Mix Solo mode, any number of channels can be soloed
simultaneously.
• LAST SOLO .................. In Last Solo mode, only one channel can be soloed at a time by
pressing the [SOLO] button. The Solo function that was previously enabled for channels is automatically cancelled.
D LISTEN
This parameter determines the source of the Input Channel Solo signal: Pre Fader or
Post Pan. When Pre Fader is selected, turning on the PAN button below the Pre Fader
option will solo the channel with the pan position specified by the Pan setting even if the
source precedes the fader. This parameter is effective only in Recording Solo mode.
01V96 Version 2—Owner’s Manual
Using the Monitor
133
E SOLO TRIM
This parameter enables you to trim the level of the Solo signal in the range of –96 dB to
+12 dB.
F FADER/SOLO RELEASE
If this check box is checked, you can unsolo the channels by raising the channel faders
that were at the level of –∞ when the Solo function was turned on. If the faders were set
to higher than –∞, the channels cannot be soloed. This setting is not effective in Mixdown Solo mode and for Output Channels.
Note: When you check the FADER/SOLO RELEASE check box, the Solo setting is temporarily cancelled.
G SOLO SAFE CHANNEL
For Mixdown Solo mode, Input Channels can be configured individually so that they
are not muted when other Input Channels are soloed (Solo Safe function). Signals from
Input Channels with the SOLO SAFE CHANNEL button turned on are always fed to the
Stereo bus, regardless of the channels’ Solo function status. You can clear all Solo Safe
settings by turning on the ALL CLEAR button.
Tip: For example, if you set the internal effects processor’s return signal to Solo Safe, you
can monitor the soloed “processed (or wet)” signals.
H MONITOR TRIM
This parameter enables you to trim the level of the monitoring signal in the range of
–96 dB to +12 dB.
I MONO
This button switches the Monitor signal into mono.
11
1 Connect a monitoring system to the MONITOR OUT connectors.
To monitor the signal via headphones, connect headphones to the PHONES jack.
2 Press the Monitor Source selector in the MONITOR section to select the monitoring signal source.
To monitor the 01V96’s internal signals, turn off the selector (the button should be raised).
To monitor the signals at the 2TR IN connectors, turn on the selector (the button should be
pushed in).
PHONES
MONITOR
2TR IN
0
LEVEL
10
MONITOR
OUT
0
LEVEL
10
PHONES
3 Adjust the monitoring level using the MONITOR [MONITOR LEVEL] control
while playing the sound sources.
To adjust the level of the monitoring signal via headphones, turn the [PHONES LEVEL]
control.
01V96 Version 2—Owner’s Manual
Monitoring
Using the Monitor
134
Chapter 11—Monitoring
Using the Solo Function
You can solo and monitor Input Channels, Aux Out 1–8, and Bus Out 1–8 using the
[SOLO] buttons on the top panel.
1 Press the [DIO/SETUP] button repeatedly until the DIO/Setup | Monitor page
appears.
2 Set the SOLO parameter to On.
Set other parameters on the page, if necessary.
3 To solo and monitor Input Channels, press the corresponding LAYER button
to select a Layer that contains the desired channels, then press the channel
[SOLO] buttons.
The channel [SOLO] button indicators and the SOLO [SOLO] indicator light up. Only the
soloed Input Channel signals are fed to the Monitor outputs.
Tip: If the SEL MODE parameter is set to Mix Solo on the DIO/Setup | Monitor page, you
can solo multiple Channels simultaneously.
4 To solo and monitor Output Channels, press the LAYER [MASTER] button,
then press the channel [SOLO] buttons.
Input and Output Channels (Aux Out 1–8, Bus Out 1–8) cannot be solo-monitored simultaneously. For example, if you solo an Input Channel, then solo an Output Channel, the
first solo channel is cancelled.
If you solo an Output Channel first, then solo an Input Channel, canceling the Input Channel’s solo will activate the Output Channel’s solo.
5 You can unsolo all soloed channels by pressing all illuminated channel
[SOLO] buttons.
The button indicators turn off. You can also unsolo all soloed channels by pressing the
SOLO [CLEAR] button.
01V96 Version 2—Owner’s Manual
135
Surround Pan
12 Surround Pan
This chapter describes surround panning, which determines how Input Channel signals are
panned within and across the stereo field.
About Surround Pan
The Surround Pan function places a sound image within a two-dimensional field using a
multi-channel playback system, and pans the image to the front, rear, left, and right in relation to the listening position. To pan the stereo image, you can use the Parameter wheel, or
[INC]/[DEC] buttons.
If each channel’s follow pan (see page 89) is turned off, you can route the signals to the corresponding Bus Outs regardless of the Surround Pan setting. This is convenient when you
wish to assign the surround source or surround effect returns to the Buses.
If “Nominal Pan” (see page 231) in the Prefer1 page is checked, the level of the Input Channels that are panned hard left or right will be used as the nominal level. If the check box is
not checked, the nominal level will be +3dB.
Note: If you save a scene with the Follow Pan function turned off while using a 01V96 that
runs firmware older than Version 2.0, the surround settings of the scene may not be played
back correctly.
You can also store the surround pan settings in a Scene. In addition to a normal Stereo
mode, the 01V96 features the following three Surround modes:
• 3-1
This mode uses four channels that include front
left, front right, front center, and rear.
Front L
Center
Front R
12
• 5.1
This mode uses six channels that include front left,
front right, rear left, rear right, front center, and
subwoofer.
Subwoofer
Front L
Rear L
Center
Front R
Rear R
01V96 Version 2—Owner’s Manual
Surround Pan
Surround
136
Chapter 12—Surround Pan
• 6.1
This mode uses seven channels that include six
channels of 5.1 mode plus rear center.
Subwoofer
Front L
Rear L
Center
Front R
Rear center
Rear R
When you select one of these Surround modes,
each surround channel signal is output as the Bus Out signal specified on the DIO/Setup |
Surr Bus page (see page 139).
The following table shows the factory-default Surround Channel to Bus Out assignment in
each Surround mode.
Surround
Mode
3-1
5.1
6.1
BUS1
BUS2
BUS3
BUS4
L
R
C
S
Front left
Front right
Center
Surround
BUS5
BUS6
BUS7
—
—
—
L
R
Ls
Rs
C
LFE
Front left
Front right
Rear left
Rear right
Center
Subwoofer
L
R
Ls
Rs
C
Bs
LFE
Front left
Front right
Rear left
Rear right
Center
Rear center
Subwoofer
—
Tip: You can set the surround pan either independently of normal panpots or in unison with
them.
Setting Up and Selecting Surround Pan Modes
To configure the surround environment, select 3-1, 5.1, or 6.1 Surround mode on the
01V96 and connect a digital MTR or multi-channel monitoring system to the 01V96.
1 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
Pan/Route | Surr Mode page appears.
2
1
3
01V96 Version 2—Owner’s Manual
Setting Up and Selecting Surround Pan Modes
137
A SURROUND MODE
•
•
•
•
This parameter enables you to select a Surround mode by using the following buttons.
The button that is turned on (highlighted) indicates the currently-selected Surround
mode.
STEREO.........................The 01V96 uses normal stereo mode (default).
3-1...................................Selects 3-1 Surround mode.
5.1 ...................................Selects 5.1 Surround mode.
6.1 ...................................Selects 6.1 Surround mode.
B PAN/SURR LINK
When this button is turned on, Input Channel panpots and stereo surround panning are
linked.
C
Press this button to display the Surr/Bus Setup page, which enables you to change the
Surround Channel to Bus Out assignment.
2 Move the cursor to the Surround mode button you want to use.
When you move the cursor to one of these buttons, speaker icons appear, indicating a typical listening position and the Surround Channel to Bus Out configuration.
• 3-1 Surround
12
Surround Pan
• 5.1 Surround
• 6.1 Surround
01V96 Version 2—Owner’s Manual
138
Chapter 12—Surround Pan
3 Press the [ENTER] button.
The confirmation window for changing the Surround mode appears.
4 Move the cursor to the YES button, then press [ENTER].
The 01V96 enters the selected Surround mode.
5 To link the Input Channel Pan setting with the stereo surround panning,
move the cursor to the PAN/SURR LINK button, then press [ENTER].
When the PAN/SURR LINK button is turned on, adjusting the Input Channel pan settings
will also change the stereo surround panning accordingly, and vice versa.
01V96 Version 2—Owner’s Manual
Setting Up and Selecting Surround Pan Modes
139
6 To change the Surround Channel to Bus Out assignment, move the cursor
to the SURR/BUS SETUP button, then press [ENTER].
The DIO/Setup | Surr Bus page appears.
1
2
3
A BUS1–BUS8
These parameters select channels to be assigned to the Bus Outs in 3-1, 5.1, and 6.1 Surround modes.
B INIT
These buttons reset the channel assignment to the default setting.
C Surround LR to Stereo
When this check box is on, the left and right front signals of the surround channels are output from the STEREO L & R connectors.
Tip:
• Pressing the DISPLAY ACCESS [SETUP] button repeatedly also displays the Surr Bus page.
• Available Bus Outs vary depending on the Surround mode. For example, in 3-1 Surround
mode, Bus Outs 1–4 are available. In 5.1 Surround mode, Bus Outs 1–6 are available, and
in 6.1 Surround mode, Bus Outs 1–7 are available.
8 Depending on the selected Surround mode or applications, patch the Bus
Out signals to the outputs, ADAT OUT channels, or slot output channels.
Connect a playback device or MTR to the output connectors.
01V96 Version 2—Owner’s Manual
12
Surround Pan
7 To change the assignment, move the cursor to the desired Bus parameter,
rotate the Parameter wheel to select a channel, then press [ENTER].
The channels are swapped between the selected Bus and the Bus to which the channel
assigned to the selected Bus was assigned previously.
140
Chapter 12—Surround Pan
■ Surround Pan Recording
To record surround pan movement to a digital MTR, route the Bus Outs to the ADAT OUT
channels or slot output channels that are connected to the digital MTR.
The following diagram illustrates an example of recording 5.1 Surround mode signals to a
digital MTR.
SURROUND
PAN
Input Channel 1
BUS1 (L)
BUS2 (R)
BUS3 (Ls)
BUS4 (Rs)
BUS5 (C)
BUS6 (LFE)
01V96
LFE LEVEL
SURROUND
PAN
Input Channel 2
LFE LEVEL
SURROUND
PAN
Input Channel 3
LFE LEVEL
Slot
Track 1
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
MY8-TD etc.
01V96 Version 2—Owner’s Manual
Track 2
Track 3
Track 4
Track 5
Track 6
8-TRACK DIGITAL
Digital MTR
Setting Up and Selecting Surround Pan Modes
141
■ Surround Pan Monitoring
To monitor surround pan movement, patch the Bus Outs to the analog outputs, to which a
monitoring system is connected.
The following diagram illustrates an example in which Bus Out 1 & 2 (left and right front
channel) signals are output from the STEREO OUT L & R connectors and Bus Out 3-6 signals are output from the OMNI OUT 1-4 connectors in 5.1 Surround mode.
SURROUND
PAN
Input Channel 1
BUS1 (L)
BUS2 (R)
BUS3 (Ls)
BUS4 (Rs)
BUS5 (C)
BUS6 (LFE)
01V96
Subwoofer
LFE LEVEL
SURROUND
PAN
Input Channel 2
Front L
Center
Front R
LFE LEVEL
SURROUND
PAN
Input Channel 3
LFE LEVEL
STEREO OUT L
STEREO OUT R
OMNI OUT 1
OMNI OUT 2
OMNI OUT 3
OMNI OUT 4
Front L
Front R
Rear L
Rear R
Multi-channel
amplifier
Center
Subwoofer
Rear R
Tip: To output left and right front signals of the surround channels from the STEREO OUT
L & R connectors, turn on the Surround LR to Stereo checkbox on the Surr Bus page.
01V96 Version 2—Owner’s Manual
Surround Pan
Rear L
12
142
Chapter 12—Surround Pan
Surround Panning
You can set the surround pan parameters for each Input Channel.
1 Make sure that the 01V96 is in any Surround mode except Stereo, then press
the [SEL] button of the channel for which you want to set surround pan.
2 Press the DISPLAY ACCESS [PAN/ROUTING] button repeatedly until the
Pan/Route | Ch Edit page appears.
The Ch Edit page displays the selected Input Channel, and its surround pan setting and
available pair partner.
The following display page is an example in 6.1 Surround mode.
1
2
3
4
5
67
98
The following parameters are available on this page:
A Surround pan graph
This graph indicates the pan positions in a two-dimensional field, with the listening
position in the center. A small diamond ( ) indicates the current surround pan position. You can move the current surround pan position (
) directly to one of the
speaker icons by selecting its icon, then pressing [ENTER].
B Trajectory patterns
These buttons represent seven trajectory patterns that determine how the surround pan
moves when you operate the Parameter wheel or the [INC]/[DEC] buttons.
C FAST
Turning on this button increases the speed of sound images panned via the Parameter
wheel.
D Trajectory pattern parameters
•
•
•
•
These parameters fine-tune the surround pan trajectory pattern.
WIDTH ................... This parameter sets the left-to-right width of the selected trajectory pattern.
DEPTH .................... This parameter sets the front-to-rear width of the selected trajectory pattern.
OFFSET ................... This parameter offsets the left-to-right direction of the selected
trajectory pattern.
OFFSET ................... This parameter offsets the front-to-rear direction of the
selected trajectory pattern.
01V96 Version 2—Owner’s Manual
Surround Panning
143
E LFE
This parameter control sets the level of the LFE (Low Frequency Effects) Channel signal
routed to the subwoofer, and appears only in 5.1 and 6.1 Surround modes.
F F/R
In 6.1 Surround mode, F and R parameter controls appear. The F parameter control
determines how the Front Center signal is fed to the Left and Right channels, and the R
parameter control determines how the rear surround signal is fed to the Left and Right
surround channels.
6 DIV
This parameter control, instead of the F/R parameter control, appears in 3-1 or 5.1 Surround mode, and determines how the Center signal is fed to the Left, Right, and Center
channels. It is expressed as a percentage ranging from 0 to 100%. When you set the
parameter to 100, the Center signal is fed to only the Center channel. When you set the
parameter to 0, the Center signal is fed to only the Left and Right channels. When you
set the parameter to 50, the Center signal is fed equally to the Left, Right, and Center
channels.
G LINK
This button is available only in 6.1 Surround mode. When you turn on this button, the
F and R controls are set to the same value, and linked together.
H ST LINK
Turning on this button links the surround pan parameters of two Input Channels that
are currently displayed on the page (Stereo Link function). You can link the surround
pan parameters of two channels regardless of whether they are paired.
I PATTERN
When Input Channels are linked by the Stereo Link function, the seven patterns selectable here determine how the linked surround pan moves via the Parameter wheel and
the [INC]/[DEC] buttons.
36
40
40
56
01V96 Version 2—Owner’s Manual
Surround Pan
3 Select one of seven trajectory patterns by turning on the corresponding trajectory pattern button.
The following patterns are available:
•
...................... The sound image moves between left and right.
12
144
Chapter 12—Surround Pan
•
...................... The sound image moves between front and rear.
36
•
36
36
36
40
56
12
8
8
44
16
20
16
...................... The sound image moves from front right to rear left. With this pattern,
you can also fine-tune the trajectory using the WIDTH, DEPTH,
OFFSET ( ), and OFFSET ( ) parameters.
36
36
•
40
...................... The sound image moves from front left to rear right. With this pattern,
you can also fine-tune the trajectory by using the WIDTH, DEPTH,
OFFSET ( ), and OFFSET ( ) parameters.
36
•
40
12
8
8
44
16
20
16
...................... The sound image moves between left and right while tracing an arc.
With this pattern, you can also fine-tune the radius and shape of the
arc using the WIDTH, DEPTH, OFFSET ( ), and OFFSET ( )
parameters.
48
01V96 Version 2—Owner’s Manual
44
44
20
32
28
56
32
24
Surround Panning
•
40
48
44
48
...................... The sound image moves between front and rear while tracing an arc.
With this pattern, you can also fine-tune the radius and shape of the
arc using the WIDTH, DEPTH, OFFSET ( ), and OFFSET ( )
parameters.
44
•
145
44
20
32
28
56
32
24
...................... The sound image moves while tracing a circle or oval. With this pattern, you can also fine-tune the radius and shape of the circle or oval
using the WIDTH, DEPTH, OFFSET ( ), and OFFSET ( ) parameters.
32
24
24
24
60
40
52
40
5 To move the sound image, move the cursor to anywhere outside the parameter boxes, then rotate the Parameter wheel.
The sound image of the selected channel moves along the selected trajectory pattern.
Tip: You can also adjust the front and rear or left and right movement, the trajectory pattern
and other parameters from an external MIDI device by assigning the surround parameters
to MIDI Control Changes (see page 220).
6 To link the surround pan settings of two channels displayed on the page,
turn on the ST LINK button.
Use the PATTERN parameter box below the ST LINK button to specify how you want the
linked surround pan to move.
01V96 Version 2—Owner’s Manual
Surround Pan
4 If necessary, fine-tune the trajectory by editing the WIDTH, DEPTH, OFFSET
( ), and OFFSET ( ) parameter values.
12
146
Chapter 12—Surround Pan
The following table shows how the sound images on two linked channels move when different trajectory patterns and stereo link patterns are combined. A solid line indicates the
movement of the selected channel, and a dotted line indicates the movement of the
linked partner.
Trajectory
Pattern
7 To list multiple-channel surround pan settings, press the [PAN/ROUTING]
button repeatedly until the Pan/Route | Surr1-16, Surr17-32, or Surr ST IN
page appears.
These pages display and enable you to edit the surround pan settings for 16 channels.
1
2
3
A Surround pan graphs
These graphs display the trajectory patterns and the current pan positions for the Input
Channels.
01V96 Version 2—Owner’s Manual
Surround Panning
147
B
parameter box
This parameter box enables you to move the surround pan setting of the selected channel left and right.
C
parameter box
This parameter box enables you to move the surround pan setting of the selected channel front and rear.
8 To move the sound image of each channel on these pages, move the cursor
to the desired channel, then rotate the Parameter wheel.
The pan setting of the channel changes along the trajectory pattern. Press [ENTER] to display the currently-selected channel’s CH Edit page.
12
Surround Pan
01V96 Version 2—Owner’s Manual
148
Chapter 12—Surround Pan
01V96 Version 2—Owner’s Manual
Grouping Channels & Linking Parameters
149
13 Grouping Channels & Linking
Parameters
This chapter describes how to group faders or [ON] buttons for multiple channels and link
the EQ or compressor parameters for simultaneous operation.
Grouping & Linking
On the 01V96, you can group faders or [ON] buttons for multiple Input Channels (Input
Channels 1–32, ST IN Channels 1–4) or multiple Output Channels (Bus Outs 1–8, Aux
Outs 1–8, Stereo Out) and link the EQ or compressor parameters.
The following elements can be grouped or linked within Input Channels or Output Channels.
• Fader group
Input Channel or Output Channel faders (or level controls) can be grouped. There are eight
Input Channel Fader groups and four Output Channel Fader groups. When channel faders
or level controls are grouped, operating any one of them enables you to control the level of
the other grouped faders or level controls while maintaining the relative level differences.
Also, the 01V96 features a Fader Group Master function that enables you to control the level
of all grouped channels using the Group Master level while maintaining the relative level
balance between channels.
• EQ Link
Input or Output Channel EQ parameters can be linked. There are four EQ links for Input
Channels and Output Channels respectively.
All channels in an EQ link share the same EQ parameter settings. When you change an EQ
parameter value for one of the linked channels, the change is applied to all other linked
channels.
• Compressor Link
Input or Output Channel compressor parameters can be linked. There are four compressor
links for Input Channels and Output Channels respectively.
All channels in a compressor link share the same compressor parameter settings. When you
change a compressor parameter value for one of the linked channels, the change is applied
to all other linked channels.
Tip: Compressor Link is not available for the ST IN Channels, since they do not feature compressors.
01V96 Version 2—Owner’s Manual
13
Grouping Channels & Linking Parameters
• Mute group
Input Channel or Output Channel [ON] buttons can be grouped. There are eight Input
Channel mute groups and four Output Channel mute groups. When channel [ON] buttons
are grouped, pressing any one of them turns the [ON] buttons for all the grouped channels
on or off. A mute group can include On channels and Off channels at the same time, which
turn off or on respectively when you press any one of the grouped [ON] buttons.
Also, the 01V96 features a Mute Group Master function that enables you to mute grouped
channels using the Master Mute buttons.
150
Chapter 13—Grouping Channels & Linking Parameters
Using Fader Groups and Mute Groups
Follow the steps below to group faders or [ON] buttons for Input Channels or Output
Channels.
1 Press the DISPLAY ACCESS [PAIR/GROUP] button repeatedly until one of the
pages that contains the desired group and channels appears.
- In Fader page
This page enables you to set Fader groups (A–H) for Input Channels 1–32 and ST IN
Channels 1–4.
- Out Fader page
This page enables you to set Fader groups (Q–T) for Bus Outs (1–8), Aux Outs (1–8)
and Stereo Out.
• In Fader page
- In Mute page
This page enables you to set Mute groups (I–P) for Input Channels 1–32 and ST IN
Channels 1–4 respectively.
- Out Mute page
This page enables you to set Mute groups (U–X) for Bus Outs (1–8), Aux Outs (1–8) and
Stereo Out.
• In Mute page
01V96 Version 2—Owner’s Manual
Using Fader Groups and Mute Groups
151
2 Press the up ( ) or down ( ) button to select a group.
3 Press the [SEL] button for a channel you wish to add to the group.
The selected channel is marked with “ ” and the channel is added to the group.
Example: Input Channels 1–4, 7, 8, and 15, 16 have been
added to Fader group C.
Tip:
• If you add one channel from a pair to a group, the pair partner is automatically added to
the group.
• You can also select a channel on another layer by switching layers.
4 In the same way, press the [SEL] button for other channels you wish to add
to the group.
The relative level of the faders for the grouped channels is determined by the position of the
faders when the channels were added to the group.
The On/Off status of the grouped channels is determined by the [ON] button status when
the channels were added to the group.
6 To use a fader group, operate one of the faders or level controls for the
grouped channels.
Note:
• If you wish to change the relative level balance between the grouped channels while this page
is displayed, first turn off the Enable button or remove the channels for which you want to
change the level from the group.
• If other pages are displayed, press and hold down the [SEL] button for the desired channels
to temporarily remove them from the group, then change the level balance.
7 To use a mute group, press one of the [ON] buttons for the grouped channels.
All channels in the group switch their on/off status.
Note:
• While a mute group is enabled, you cannot turn a subset of the grouped channels on or off.
• If you wish to turn a subset of the grouped channels on or off, first turn off the Enable button,
or remove the channels you wish to turn on or off from the group.
01V96 Version 2—Owner’s Manual
13
Grouping Channels & Linking Parameters
5 To turn a group on or off, move the corresponding button in the ENABLE
column, then press [ENTER].
When the group Enable button is turned off, the corresponding group is temporarily cancelled.
152
Chapter 13—Grouping Channels & Linking Parameters
Using Fader Group Master
The 01V96 features a Fader Group Master function that enables you to control the level of all
channels using the Group Master level while maintaining the relative balance between channels, much like a VCA group on an analog mixing console. While this function is enabled,
channel fader operation does not affect channel levels in the corresponding Fader group.
1 After you perform Step 5 in “Using Fader Groups and Mute Groups” on
page 150, use the cursor buttons to select the INPUT FADER MASTER check
box or the OUTPUT FADER MASTER check box, then press [ENTER] to turn
on the Fader Group Master function.
2 When the Fader Master check box is checked, you can set channel levels of
the Fader groups in the Master column.
When the Master column is selected, repeatedly pressing the [ENTER] button turns the
Fader group on and off.
You can also make these settings in the In Master page or Out Master page, as shown below.
3 Press the DISPLAY ACCESS [GROUP] button repeatedly until the Group | In
Master or Group | Out Master page appears.
4 Use the cursor buttons to select parameters, then use the Parameter wheel,
INC/DEC buttons, or [ENTER] button to set the parameters.
• INPUT/OUTPUT FADER MASTER ... When this check box is checked, you can set the
master levels for the Fader groups. The resultant Channel level equals the corresponding
Channel fader level plus the Group Master
level.
01V96 Version 2—Owner’s Manual
Using Mute Group Master
153
• ALL NOMINAL............This button resets the master levels for all Fader groups to nominal.
• ON/OFF.........................This turns each Input Fader group on or off. This function
works like a VCA mute on an analog mixing console.
• Faders ............................These faders adjust the master levels of the Fader groups. Fader
knobs are highlighted when faders are set to 0.0 dB. Press the
[ENTER] button to set the currently-selected fader to 0.0 dB.
You can also control the parameters from the channel strips on the control surface as
described below by using the User Assignable Layer of the Remote Layers. See page 233for
information on the User Assignable Layer.
• [SEL] buttons ...............These buttons move the cursor on the In Master page or Out
Master page.
• [SOLO] buttons ...........These buttons turn the Solo function of each Fader group on
and off. You can monitor all the channels in each Fader group.
• Channel Faders ............The channel faders enable you to set the master level for each
Fader group.
Using Mute Group Master
In addition to the Mute Group function that links the operation of channel [ON] buttons,
the 01V96 features a Mute Group Master function that enables you to mute grouped channels using the Master Mute buttons in a manner similar to using a mute group on an analog
mixing console. While this function is enabled, the [ON] buttons for grouped channels will
not be linked.
1 After you perform Step 5 in “Using Fader Groups and Mute Groups” on
page 150, use the cursor buttons to select the INPUT MUTE MASTER check
box or OUTPUT MUTE MASTER check box, then press [ENTER] to turn on
the Mute Group Master function.
01V96 Version 2—Owner’s Manual
Grouping Channels & Linking Parameters
2 When the Mute Master check box is checked, use the group MASTER MUTE
buttons to mute or unmute the groups.
If channels are muted via the Mute Master function, the channel [ON] button indicators
flash. It is useful if you assign the MASTER MUTE buttons to USER DEFINED KEYS buttons.
13
154
Chapter 13—Grouping Channels & Linking Parameters
Linking EQ and Compressor Parameters
Follow the steps below to link EQ or compressor parameters for Input Channels or Output
Channels. This function enables you to set EQ or compressor parameters for multiple channels to the same values simultaneously.
1 Press the DISPLAY ACCESS [PAIR/GROUP] button repeatedly until one of the
following pages appears.
- In EQ page
This page enables you to set EQ links (a–d) for Input Channels 1–32 and ST IN Channels 1–4.
- Out EQ page
This page enables you to set EQ links (e–h) for Bus Outs (1–8), Aux Outs (1–8) and Stereo Out.
01V96 Version 2—Owner’s Manual
Linking EQ and Compressor Parameters
155
- In Comp page
This page enables you to set Compressor links (i–l) for Input Channels 1–32.
- Out Comp page
This page enables you to set Compressor links (m–p) for Bus Outs (1–8), Aux Outs
(1–8) and Stereo Out.
13
01V96 Version 2—Owner’s Manual
Grouping Channels & Linking Parameters
2 Press the up ( ) or down ( ) cursor button to select a link to which you want
to add channels.
156
Chapter 13—Grouping Channels & Linking Parameters
3 Press the [SEL] button for a channel you wish to add to the EQ or Compressor
link.
The selected channel is marked with “ ” and the channel is added to the link.
Example: Input Channels 1–4, 7, 8, 12 and 14 have been
added to EQ link b.
Tip:
• If you add one channel from a pair to a link, the pair partner is automatically added to the
link.
• You can also select a channel on another layer by switching layers.
4 In the same way, press the [SEL] button for other channels you wish to add
to the link.
The EQ or compressor settings for the first channel added to the link are applied to all subsequently-added channels.
5 After all desired channels are added to the link, edit the EQ or compressor
parameters for one of the linked channels.
The edits for the EQ or compressor parameters are applied to the rest of the linked channels.
01V96 Version 2—Owner’s Manual
Internal Effects
157
14 Internal Effects
This chapter describes how to use the 01V96’s internal effects processors.
About the Internal Effects
The 01V96 features four internal multi-effects processors. These effects processors offer
numerous types of effects, including reverbs, delays, modulation-based effects, and combination effects designed especially for use with surround sound.
Note: When the 01V96 operates at a high sampling frequency (88.2 kHz or 96 kHz), you can
use only Effects processors 1 and 2.
OUTPUT
EFFECT 2
OUTPUT
1
2
EFFECT 3
OUTPUT
1
2
EFFECT 4
OUTPUT
1
2
SELECT
INSERT OUT
INPUT PATCH
INPUT
1
2
INPUT
1
2
1
2
INPUT
FX2 SEND
1-2
1
2
EFFECT 1
INPUT
FX1 SEND
1-2
1
2
FX3 SEND
1-2
AUX1-8
FX4 SEND
1-2
Processor inputs and outputs can be patched to various sources. For example, effects processor inputs can be fed from the Aux Sends and output to ST IN Channels (effects
send/return). Effects processors can also be inserted into Input Channels, Bus Outs, Aux
Outs, or the Stereo Out.
Effects processors 1 through 4 create 1-in/2-out or 2-in/2-out effects.
The 01V96 also features the Effects library, which contains 53 preset programs (including
Add-On Effects) and 75 user programs.
14
Internal Effects
01V96 Version 2—Owner’s Manual
158
Chapter 14—Internal Effects
Using Effects Processors via Aux Sends
You can use effects processors via Aux Sends by patching effects processor inputs to Aux
Outs, and effects processor outputs to ST IN Channels.
1 Recall an effect program you wish to use.
Refer to page 179 for more information on recalling effect programs.
2 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch | Effect
page appears.
This page enables you to patch all inputs and outputs of Effects processors 1–4.
1
3
2
This page contains the following parameters:
A IN
These parameter boxes select the signals to be fed to the effects processors.
B OUT
These parameter boxes select the destination of the signals output from the effects processors.
C
button
This button recalls the FX1 Edit–FX4 Edit pages, which enable you to adjust the effect
parameters.
3 To select a signal to be input to the effects processor, move the cursor to
the desired In parameter box, select a signal from the following options,
then press [ENTER].
• – ..................................... No assignment
• AUX1–8 ......................... Aux Sends 1–8
• INS CH1–32 ................. Input Channel 1–32 Insert Out
• INS BUS1–8.................. Bus 1–8 Insert Out
• INS AUX1–8 ................. Aux Send 1–8 Insert Out
• INS ST-L/R.................... Stereo Out Insert Out
To use the internal effects processors via Aux Sends, select Aux 1–8 (in most cases).
You can patch a different signal to the other input of 2-in/2-out effect programs.
01V96 Version 2—Owner’s Manual
Using Effects Processors via Aux Sends
159
Tip:
• You can patch a signal to multiple effect inputs.
• Move the cursor to an IN parameter box and press the [ENTER] button. The Patch Select
window appears. This window enables you to select the input source quickly.
4 To patch a signal output from the effects processor, move the cursor to the
desired OUT parameter box, select the signal destination from the following
options, then press [ENTER].
• – .....................................No assignment
• CH1–32 .........................Input Channels 1–32
• ST IN 1L–ST IN 4R ......ST IN Channels 1L–4R
• INS CH1–32..................Input Channel Insert In
• INS BUS1–8 ..................Bus 1–8 Insert In
• INS AUX1–8..................Aux 1–8 Insert In
• INS ST-L & INS ST-R...Stereo Bus Insert In
To use the internal effects processors via Aux Sends, select CH 1–32 or ST IN 1–4 (in most
cases). The channels you assign here will become the effects return channels.
You can patch a different channel to the other output of a 1-in/2-out or 2-in/2-out effect
program to create stereo effects.
Tip:
• If you select an ST IN Channel as the destination, you can patch the L and R channel signals
separately.
• You can also use the Patch Select window to set the OUT parameter boxes, as explained in
Step 3.
• The number of inputs available for each effect varies depending on the type of effect programs
initially recalled.
Note: You cannot select a channel as the destination of multiple effect signals. If you select a
channel that is already selected in another OUT parameter box, that OUT parameter box
switches its indicator to “–” (not assigned).
5 Adjust the level of Aux Sends patched to the effects processor.
Refer to “9 Aux Outs” on page 109 for information on setting the Aux Sends.
Tip: Use the Master layer fader to adjust the final Aux Send output level. At this time, you
can view the level on the Meter | Master page (see page 35).
6 Adjust the level, pan, and EQ of the Input Channels patched to the effect
outputs.
Tip: To mix the effects sound returned via the Aux sends with the original dry sound, set the
effect’s MIX BALANCE parameter to 100% (only the effects sound will be output).
01V96 Version 2—Owner’s Manual
Internal Effects
Note: Do not raise the level of the Aux Sends (patched to the effects processor’s input) on the
effects return channels. Otherwise, the signal will return to the same channel, creating a signal
loop and possibly damaging your speakers.
14
160
Chapter 14—Internal Effects
Inserting the Internal Effects into Channels
You can insert the internal effects into certain Input Channels or Output Channels (Bus
1–8, Aux Bus 1–8, or the Stereo Bus).
Note:
• You cannot use Insert In and Out for ST IN Channels.
• If effects are inserted in channels, you cannot use those effects via Aux Sends or insert them
into other channels.
1 Select an internal Effects processor (1–4), then recall the desired effect programs.
2 Press the [SEL] button of the Input Channel or Output Channel into which
you want to insert the selected effects.
Tip: Repeatedly pressing the STEREO [SEL] button toggles between the left and right Stereo
Bus channels.
3 Press the DISPLAY ACCESS [ /INSERT/DELAY] button repeatedly until the
/Ins/Dly | Insert page appears.
4 Select the effect insertion position using the INSERT button in the POSITION
section.
5 Move the cursor to the OUT parameter box in the INSERT section, then select
the inputs of the effects processor selected in Step 1.
• FX1-1 & FX1-2 ............. Inputs 1 & 2 of Internal Effects Processor 1
• FX2-1 & FX2-2 ............. Inputs 1 & 2 of Internal Effects Processor 2
• FX3-1 & FX3-2 ............. Inputs 1 & 2 of Internal Effects Processor 3
• FX4-1 & FX4-2 ............. Inputs 1 & 2 of Internal Effects Processor 4
6 Press [ENTER] to confirm the setting.
7 Move the cursor to the IN parameter box in the INSERT section, select the
outputs of the effects processor selected in Step 1, then press [ENTER] to
confirm the setting.
8 Move the cursor to the ON/OFF button in the INSERT section, then press
[ENTER] to turn on the button.
Effect insertion is now enabled.
01V96 Version 2—Owner’s Manual
Editing Effects
161
Tip:
• After inserting effects to channels, adjust the MIX BALANCE parameter for the effects,
according to the purpose and effects type.
• Move the cursor to an empty IN or OUT parameter box and press the [ENTER] button.
The Patch Select window appears, which enables you to quickly select available signal paths.
Editing Effects
To edit effect programs recalled to the internal Effects processors 1–4, press the DISPLAY
ACCESS [EFFECT] button repeatedly until the Edit page for the effects processor you wish
to edit appears.
Effects processors 1–4 correspond to the following pages:
• Effects Processor 1.......FX1 Edit page
• Effects Processor 2.......FX2 Edit page
• Effects Processor 3.......FX3 Edit page
• Effects Processor 4.......FX4 Edit page
These Edit pages contain the following effect parameters.
1
2
3
4
5
7
6
14
This parameter displays the name of the effect program currently used by the effects
processor.
B TYPE
This parameter displays the type of effect program currently used by the effects processor. The I/O configuration of the effect program is displayed below this parameter.
C
button
Move the cursor to this parameter, then press [ENTER] to display the Library page for
the selected effects processor.
D
button
Move the cursor to this button, then press [ENTER] to display the Patch | Effect page,
which enables you to assign signals to the inputs and outputs of Effects processors 1–4.
E MIX BALANCE
This parameter knob enables you to set the balance between wet and dry signals. When
the parameter is set to 0%, only the dry signal is heard. When set to 100%, only the wet
signal is heard. Turn on the BYPASS button to bypass the currently-selected effects processor.
01V96 Version 2—Owner’s Manual
Internal Effects
A EFFECT NAME
162
Chapter 14—Internal Effects
F TEMPO
This section enables you to set the tempo and interval of the selected effects, and displays
certain parameters only when certain effect types are selected. Use the parameter control
on the left side of this section to adjust the value between 25BPM and 300BPM. When
the MIDI CLK button is on, the 01V96 updates the TEMPO data (BPM) based on the
MIDI Clock information received at the MIDI IN port. You can also specify the tempo
by moving the cursor to the TAP TEMPO button and double-clicking the [ENTER]
button. The 01V96 calculates the tempo based on the time interval between your two
taps (clicks) on the [ENTER] button.
Tip: If the Freeze effect is selected, the TEMPO section displays the record and playback
buttons for using the effect, the recording data condition, and a progress bar that indicates
the current status.
G Meters
These meters indicate the input or output levels of the currently-selected effects processor. Select the IN button or OUT button to display the input levels or output levels
respectively.
Tip: You can also view the input and output levels of the effects processors on the Meter |
Effect 1–4 pages (see page 34).
Move the cursor to a parameter you wish to change, and rotate the Parameter wheel or
press the [INC]/[DEC] buttons to adjust the setting. You can store the edited settings as
a new program in the Effects library (see page 179).
Note: You cannot change the effects type on this page. To change the effects type, recall a
program that uses the desired effects type from the Effects library.
About Add-On Effects
Installing optional Add-On Effects packages enables you to expand your effects selection
beyond the internal effects. Add-On Effects will be stored in and recalled from preset #45
and the subsequent preset programs. You can also store edited effects in user program #54
and the subsequent user programs. For more information on Add-On Effects, refer to the
installation guide that is included in your Add-On Effects packages.
01V96 Version 2—Owner’s Manual
About Plug-Ins
163
About Plug-Ins
If you installed a mini-YGDAI card that supports the Effects function into Slot, you can use
plug-in effects in addition to the internal effects processors.
You can patch Bus signals or channel insert outs to the plug-in input. The plug-in output
can be patched to Input Channels or channel insert ins.
To use the plug-in effects, press the [EFFECT] button repeatedly until the Effect | P-In Edit
page appears.
For details on using plug-ins, refer to the owner’s manual that came with the plug-in card.
As of July 2004, the 01V96 supports the following plug-in cards. Visit the Yamaha web site
(http://www.yamahaproaudio.com/) for the latest information on compatible plug-in
cards.
• Waves .............................Y56K
The Y56K card setting is stored in memory in the card when you store scenes, and is recalled
at the time of scene recall. The setting is not stored in a scene memory on the 01V96. Therefore, the setting does not support the scene memory’s Global Paste, Sort, and Auto Update
functions.
01V96 Version 2—Owner’s Manual
14
Internal Effects
Note: The Y56K card supports scenes #1-96. If you store or recall a scene # 97 or subsequent
scenes, the Y56K card setting will not respond. (In this case, a warning message appears.)
164
Chapter 14—Internal Effects
01V96 Version 2—Owner’s Manual
Scene Memories
165
15 Scene Memories
This chapter describes Scene memories, which store 01V96 mix and effects settings.
About Scene Memories
Scene memories enable you to store a snapshot of 01V96 channel mix settings and internal
effects processor settings as a “Scene” in a special memory area.
There are 99 Scene memories, and you can recall any Scene using the display pages or the
controls on the top panel.
Tip:
• You can recall Scenes by transmitting Program Changes from external MIDI devices (see
page 219).
• You can back up Scene memories to external MIDI devices by using MIDI Bulk Dump (see
page 226).
What is Stored in a Scene?
The following parameter settings are stored in a Scene:
Scene
Parameters
All channel faders (and level controls)
Channel to Aux Out 1–8 Send levels
Aux Out 1–8 & Bus Out 1–8 levels
All channel [ON] button settings
All channel Phase settings
All channel Attenuator settings
All channel Delay settings (excluding ST IN Channels)
Mix parameters
All channel Compressor settings (excluding ST IN Channels)
Input channel Gate settings (excluding ST IN Channels)
All channel EQ settings
All channel Pan settings
All channel routings
Fader groups, Mute groups, Fader group Masters, Mute group Masters, EQ
links, and Compressor links
All channel pair settings
Effect programs recalled for Effects processors 1–4 and their parameter settings
Remote Layer
Fader and [ON] button status (only when Remote Control Target is set to
USER DEFINED)
Scene settings
Scene titles and Fade Time settings
Input Patching
Currently-selected Input Patch library number
Output Patching
Currently-selected Output Patch library number
Note:
• Scenes take a snapshot of Input and Output Patch library numbers that are in use at the
time the Scene is stored, but exclude current (edited) Input and Output patching.
• If you do not store the edited Input and Output patching to the libraries, recalling a Scene
may change the current patching.
01V96 Version 2—Owner’s Manual
Scene Memories
Effects parameters
15
166
Chapter 15—Scene Memories
About Scene Numbers
Scene memories are numbered with #U or from #00 through #99. You can store Scenes in
Scene memories #01–99. When you recall a Scene, the Scene memory number appears at
the top of the display page.
Scene memory #00 is a special read-only memory that contains the default settings of
all mix parameters. To reset all mix parameters on the 01V96 to their initial or default
values, recall Scene memory #0.
Also, the Initial Data Nominal check box on the Setup | Prefer1 page (see page 230) enables
you to specify whether Input Channel faders are set to either 0 dB or –∞ dB when Scene
memory #0 is recalled.
Scene memory “Ud” is a special read-only memory that contains the mix settings in
effect immediately before the most recently recalled or stored Scene. To undo or redo
Scene memory recall and store operations, recall Scene memory #U.
When you adjust parameters after recalling a Scene, the Edit indicators appear (“EDIT” at
the top of the display), indicating that the mix settings no longer match those of the Scene
that was most recently recalled. The contents of the Edit Buffer (where the current mix settings are stored) are retained while the 01V96 is turned off. This allows the 01V96 to restore
the edited mix settings when you turn on the power.
Display
Edit indicator
The contents of recalled Scene memory
#2 match the current settings on the
01V96, and the Edit indicator remains off.
01V96 Version 2—Owner’s Manual
The parameters of recalled Scene memory #2
were edited. Therefore, the Edit indicators
appear, indicating that the current settings on
the 01V96 do not match Scene memory #2.
Storing and Recalling Scenes
167
Storing and Recalling Scenes
You can store and recall Scenes by pressing the buttons on the top panel or using the dedicated Scene memory page on the display.
Note:
• When you store Scenes, make sure that there are no settings in the Edit Buffer that you do
not want to store. Make sure that no settings, especially faders, have been adjusted unintentionally.
• If you are not sure of the Edit Buffer’s contents, recall the last Scene, make the adjustments
you want, then store the Scene. You may wish to store the current Scene to an unused Scene
memory, just in case.
Storing and Recalling Scenes Using the SCENE MEMORY
Buttons
You can use the SCENE MEMORY buttons to store and recall Scenes.
1 Adjust the mix parameters on the 01V96 to the conditions you wish to store
as a Scene.
2 Press the SCENE MEMORY Up [ ] or Down [ ] buttons to select a Scene
memory number.
If you select a Scene memory other than the currently-recalled Scene, its number flashes at
the to of the display.
Scene memories #U (“Ud”) and #0 (“00”) are special read-only memories, to which you
cannot store Scenes. Also, you cannot store Scenes to write-protected Scene memories (see
page 168).
3 Press the SCENE MEMORY [STORE] button.
The Title Edit window appears, which enables you to name the Scene to be stored.
Tip: You can disable this window by turning the Store Confirmation parameter to Off on the
DIO/Setup | Prefer1 page (see page 230). In this case, the stored Scene will hve the same name
as the one recalled most-recently.
4 Enter the title, move the cursor to the OK button, then press [ENTER].
The Title Edit window closes and the current Scene is stored to the selected Scene memory.
Tip: If you turn the Recall Confirmation parameter to On on the DIO/Setup | Prefer1 page,
a Scene recall confirmation window for Scene recalls appears before the Scene is recalled (see
page 230).
01V96 Version 2—Owner’s Manual
15
Scene Memories
5 To recall a Scene, press the SCENE MEMORY Up [ ] or Down [ ] buttons to
select a Scene memory number, then press the SCENE MEMORY [RECALL]
button.
168
Chapter 15—Scene Memories
Storing and Recalling Scenes Using the Scene Memory Page
On the Scene Memory page, you can store, recall, write-protect, delete, and edit the titles of
Scenes.
1 Adjust the mix parameters on the 01V96 to the conditions you wish to store
as a Scene.
2 Press the DISPLAY ACCESS [SCENE] button repeatedly until the Scene | Scene
page appears.
1
2
3
4
5
6
7 8
3 Rotate the Parameter wheel or press the [INC]/[DEC] buttons to select a
Scene memory, move the cursor to one of the following buttons, then press
[ENTER].
A TITLE EDIT
Select this button to display the Title Edit window, which enables you to edit a selected
Scene title.
B RECALL
This button recalls the contents of the selected Scene memory.
C STORE
This button stores the current Scene to the selected Scene memory. By default, a confirmation window appears before you store the Scene.
D CLEAR
This button deletes the contents of the selected Scene memory.
E PROTECT ON/OFF
This button switches on and off the write-protection of the contents of the selected
Scene memory. A padlock icon ( ) appears next to the title of a Scene memory that is
write-protected.
F Library list
Scene memories 01–99 are listed in the library memory title list. The titles of stored
Scenes are indicated in the title column. The message “No Data!” appears in the title column of empty library memories. The selected memory appears inside the dotted box
between the
and
marks.
01V96 Version 2—Owner’s Manual
Auto Scene Memory Update
169
G PATCH LINK INPUT
This indicates the Input Patch library number that is linked to each scene. When you
store a scene, the number of the input patch that was most recently recalled or stored
will automatically be linked with that scene. When you recall that scene, this library
number will also be automatically recalled. You can also move the cursor to the parameter boxes and change the library numbers.
H PATCH LINK OUTPUT
This indicates the Output Patch library number that is linked to each scene. When you
store a scene, the number of the output patch that was most recently recalled or stored
will automatically be linked with that scene. When you recall that scene, this library
number will also be automatically recalled. You can also move the cursor to the parameter boxes and change the library numbers.
Auto Scene Memory Update
If the Scene MEM Auto Update check box on the Setup | Prefer1 page (see page 230) is
turned on, parameter edits are stored automatically in a Shadow memory, which is available for each Scene. This is called the Auto Update function.
If the Auto Update function is enabled, parameter edits made after the Scene was recalled
are stored in the Scene’s Shadow memory. When you again recall the Scene, the contents of
the Original and Shadow memories are recalled alternately.
Therefore, even after you recall the Original Scene memory, you can recall the edited
version from Shadow memory to restore the most recent edits.
If the “EDIT” indicator appears at the top of the display, the edited version from Shadow
memory has been recalled.
Display
Edit indicator
Original Scene
Shadow memory
If a Shadow memory is recalled, the edited version is stored when you store the Scene. (The
contents of the Original and Shadow memories then become identical.)
15
Scene Memories
01V96 Version 2—Owner’s Manual
170
Chapter 15—Scene Memories
Fading Scenes
You can specify the time it takes the Input and Output Channel faders (or level controls) to
move to their new positions when a Scene is recalled. This is called Fade Time, and it can be
set for each channel in the range of 00.0 through 30.0 seconds (in 0.1 second steps). You can
set the Fade Time for each Scene individually or for all Scenes globally.
Fading Input Channels
To set the Fade Time for Input Channels 1–32 and ST IN Channels 1–4, press the DISPLAY
ACCESS [SCENE] button repeatedly until the Scene | In Fade page appears. Move the cursor to the desired channel parameter box, then rotate the Parameter wheel or press the
[INC]/[DEC] buttons to modify the Fade Time setting.
1
2
3
A Global Fade Time
When this check box is checked, a Scene is recalled using the currently-specified Fade
Time. (The Fade Time setting stored in the recalled Scene is temporarily ignored.) This
check box setting works in unison with the Out Fade page.
B ALL INPUT CLEAR
This button resets all channel Fade Times on the page to 00.0 second.
C INPUT CH1–32/ST IN 1–4
These parameters enable you to set the Fade Time for each Input Channel in the range
of 00.0 through 30.0 seconds. The Fade Time setting for one channel in a pair works in
unison with its partner.
Tip:
• If you operate a fader while fading channels, the fader’s Fade Time setting is temporarily
ignored.
• You can copy the currently-selected Input Channel Fade Time to all Input Channels by double-clicking the [ENTER] button to display a window for copying. This is convenient when
you wish to set the Fade Time for all channels simultaneously.
01V96 Version 2—Owner’s Manual
Fading Scenes
171
Fading Output Channels
To set the Fade Time for the Output Channels (Stereo Out, Bus Outs 1–8, Aux Outs 1–8),
press the DISPLAY ACCESS [SCENE] button repeatedly until the Scene | Out Fade page
appears.
The basic operation is the same as on the In Fade page.
1
2
3
4
5
A BUS1–8
These parameters enable you to set the Fade Time for each Bus Out (1–8) in the range
of 00.0 through 30.0 seconds.
B AUX1–8
These parameters enable you to set the Fade Time for Aux Outs 1–8.
C STEREO
This parameter enables you to set the Fade Time for the Stereo Out.
D INPUT MASTER A–H
These parameters enable you to set the Fade Time for Input Fader Group Master A–H.
E OUTPUT MASTER Q–T
These parameters enable you to set the Fade Time for Output Fader Group Master Q–T.
Tip: You can copy the currently-selected Output Channel Fade Time setting to all Output
Channels by double-clicking the [ENTER] button.
15
Scene Memories
01V96 Version 2—Owner’s Manual
172
Chapter 15—Scene Memories
Recalling Scenes Safely
When a Scene is recalled, all mix parameters are set accordingly. However, in some situations, you can retain the current settings of certain parameters on certain channels by
using the Recall Safe function. You can set the Recall Safe function parameters for each
Scene individually or for all Scenes globally.
To set the Recall Safe function, press the DISPLAY ACCESS [SCENE] button repeatedly
until the Scene | Rcl Safe page appears.
1
2
3
4
A Global Recall Safe
When this check box is checked, Recall Safe settings stored in Scene memories are
ignored and the current settings are retained.
B SAFE
This parameter enables or disables the Recall Safe function.
C MODE
•
•
•
•
•
•
•
•
•
•
•
The following MODE buttons determine which Safe channel parameters will remain
unaffected by Scene recalls. The MODE buttons correspond to the following parameters:
ALL ................................ All parameters
FADER........................... Channel faders (or level controls)
ON.................................. Channel On/Off parameters
PAN................................ Channel Pan parameters, Stereo Out balance
EQ .................................. Channel EQ parameters
COMP............................ Channel Comp parameters
GATE ............................. Channel Gate parameters
AUX ............................... Channel Aux Send levels, Pre/Post
AUX ON ........................ Aux Send On/Off parameters
DELAY........................... Channel Delay parameters
ROUTING .................... Channel Routing parameters
Tip: The ALL button is mutually exclusive of the other buttons.
D RECALL SAFE CHANNEL section
This section enables you to select which channels will remain unaffected by Scene
recalls, including Input Channels 1–32, ST IN Channels 1–4, Bus Outs 1–8, Aux Outs
1–8, Stereo Out, internal effects, USER DEFINED Remote layers, and plug-in effects.
The Recall Safe function is effective on channels and functions for which the buttons are
turned on.
01V96 Version 2—Owner’s Manual
Sorting Scenes
173
Sorting Scenes
You can sort Scenes in Scene memories.
1 Press the DISPLAY ACCESS [SCENE] button repeatedly until the Scene | Sort
page appears.
1
2
2 Move the cursor to the SOURCE list (1) in the left column, then rotate the
Parameter wheel or press the [INC]/[DEC] buttons to select the Scene memory you wish to move.
3 Move the cursor to the DESTINATION list (2) in the right column, then
rotate the Parameter wheel or press the [INC]/[DEC] buttons to select the
position to which you want to move the source Scene memory.
4 Press [ENTER] to move the source Scene memory to the specified destination.
The Scene memory numbers are updated accordingly.
Copying and Pasting a Scene (Global Paste)
1 Press the DISPLAY ACCESS [SCENE] button repeatedly until the Paste SRC
page appears.
01V96 Version 2—Owner’s Manual
15
Scene Memories
Any channel or parameter settings for the current scene can be copied and pasted into one
or more scenes. This function is useful when you want to apply edited parameter settings in
the current scene to other scenes.
174
Chapter 15—Scene Memories
2 Use the cursor buttons, [SEL] buttons, or Parameter wheel to select the channel category, then use the [ENTER] button or the INC/DEC buttons to select
the copy source channel.
The number of the source channel is highlighted.
You can also select Group Masters, internal Effects, and a User Defined Remote layer as copy
sources.
3 Use the cursor buttons or Parameter wheel to select the copy source parameter, then press the [ENTER] button.
4 Press the DISPLAY ACCESS [SCENE] button repeatedly until the Paste DST
page appears.
5 Use the Parameter wheel or INC/DEC buttons to select the destination
scene(s).
Scenes specified between FROM and TO (inclusive) become the paste destination. You can
paste up to 10 scenes at a time.
6 Use the cursor buttons to select the PASTE button, then use the [ENTER] button to paste the settings.
You cannot paste the settings to write-protected scenes.
To restore the previous settings that existed before the paste operation, click the UNDO
button, then press [Enter]. However, if the settings in the scene are changed after the paste
operation (such as by saving, clearing, or sorting the scene, or receiving scene data via MIDI
Bulk Dump), the UNDO function is disabled. Also, note that you will not be able to undo
the operation after you turn off the power to the console.
01V96 Version 2—Owner’s Manual
Libraries
175
16 Libraries
This chapter describes the 01V96’s various libraries.
About the Libraries
The 01V96 features seven libraries that enable you to store Channel, Input Patch, Output
Patch, Effects, and other data. You can also quickly recall this data from the libraries to
restore previous parameter values.
The 01V96 offers the following libraries:
• Channel Library
• Input Patch Library
• Output Patch Library
• Effects Library
• Gate Library
• Compressor Library
• EQ Library
Tip:
• You can store library data to a computer hard disk using the included Studio Manager software. Be sure to back up your important data.
• You can also store library data to an external MIDI device, such as a MIDI data filer, by
using MIDI Bulk Dump (see page 226).
General Library Operation
Most library functions are the same for each library.
1 Use the buttons on the top panel to locate the desired library pages.
The procedure for locating library pages varies depending on the library. Refer to the latter
part of this chapter for more information on how to display the desired library page.
The example below assumes you have located the Input Patch library page.
16
1
Libraries
2
3
4
The library memory title list is displayed in the middle of the page. The message “No Data!”
appears in the title column of empty library memories.
An “ ” icon is displayed next to the name of read-only preset memories. You cannot store,
clear, or edit the titles of these memories.
Memories #0 and #U are special read-only memories. Recall memory #0 to reset the parameter settings to their initial values. Recall #U to undo memory recall and store operations.
01V96 Version 2—Owner’s Manual
176
Chapter 16—Libraries
2 Rotate the Parameter wheel or press the [INC]/[DEC] buttons to select the
desired memory.
The selected memory appears inside the dotted box.
3 Move the cursor to one of the following function buttons, then press
[ENTER].
A TITLE EDIT
This button displays the Title Edit window, which enables you to edit the title of the
selected memory. Move the cursor to the OK button, then press [ENTER] to confirm
the edited title. Refer to page 30 for more information on entering characters.
B RECALL
This button recalls the contents of the selected library memory. If you turn on the Recall
Confirmation parameter on the DIO/Setup | Prefer1 page, the 01V96 displays a memory
recall confirmation window.
C STORE
This button stores the settings to the selected memory. Before you store the settings, you
can enter or edit the title using the Title Edit window. Refer to page 30 for more information on entering characters.
You can disable the Title Edit window by turning off the Store Confirmation parameter
on the DIO/Setup | Prefer1 page. If you bypass the Edit Title window, the name “New
Data” will be used as a title for the Scene memory.
D CLEAR
This button deletes the contents of the selected memory. After you press [ENTER], the
01V96 displays a confirmation window. To execute the delete operation, move the cursor to the YES button in the confirmation window, then press [ENTER].
Note: If you select a memory that already contains settings and execute the delete operation,
the settings will be lost. Make sure that you do not accidentally delete important settings.
01V96 Version 2—Owner’s Manual
Using Libraries
177
Using Libraries
Channel Library
Channel library enables you to store and recall Input Channel and Output Channel parameter settings. The library contains two preset memories and 127 user (readable & writable)
memories.
You can recall only the settings for the currently-selected channels from the Channel library.
For example, you cannot recall Input Channel 1–32 settings to ST IN Channels 1–4, Bus
Outs 1–8, Aux Outs 1–8, or Stereo Out, with the exception that memories #0 and #1 can be
recalled to any channels.
Follow the steps below to use the Channel library.
1 Press the DISPLAY ACCESS [VIEW] button repeatedly until the View | Library
page appears.
1
2
3
4
A SEL CH
This parameter indicates the currently-selected channel.
B CURRENT CONFIGURATION section
If the currently-selected channel is an Input Channel (1–32) or ST IN Channels (1–4),
its Surround mode and Aux configuration information is displayed here.
C Level meters
These meters indicate the levels of the currently-selected channel and the available partner.
D STORED FROM
2 Use the LAYER buttons to select layers, then press the [SEL] buttons to select
channels.
For details on the Store and Recall functions, see “General Library Operation” on page 175.
If the selected memory’s channel type does not match the type of the destination channel,
an alarm mark ( ) and the word “CONFLICT” appear next to the STORED FROM
parameter. These alarms indicate that you tried to recall unrecallable channel settings to the
currently-selected channel.
01V96 Version 2—Owner’s Manual
Libraries
This parameter indicates the channel for which the settings were originally stored in the
selected library memory. If the currently-selected library memory contains Input Channel 1–32 and ST IN Channels 1–4 settings, its Surround mode and Aux pairing information are also displayed below this parameter.
16
178
Chapter 16—Libraries
The alarm indicators also appear when the Surround mode, Aux pair, and other non-channel parameter settings originally stored in the memory do not match those for the destination channel. However, if the channel type of the memory and that of the destination
channel match, you can recall the settings even with the alarm indicators displayed. (For
unmatched parameter settings, the 01V96 will use the settings in the memory that is to be
recalled.)
The following preset memories are available for the Channel library.
No.
Preset Name
Description
0
Reset (–∞ dB)
This preset memory resets all parameters of the currently-selected channel
to their initial values and sets the channel fader level to (–∞ dB).
1
Reset (0 dB)
This preset memory resets all parameters of the currently-selected channel
to their initial values and sets the channel fader level to 0 dB (i.e., nominal).
Input Patch Library
The Input Patch library enables you to store and recall all Input Patch settings. The library
contains one preset memory and 32 user (readable & writable) memories.
To access the Input Patch library, press the DISPLAY ACCESS [PATCH] button repeatedly
until the Patch | IN LIB page appears. For details on storing and recalling memories, see
“General Library Operation” on page 175.
Input Patch preset memory #0 contains the following settings:
Input Channels 1–16
INPUT connectors 1–16
Input Channels 17–24
ADAT IN Channels 1–8
Input Channels 25–32
Slot Channels 1–8
ST IN Channels 1–4
Internal Effects Processor 1–4 Outputs 1 & 2
01V96 Version 2—Owner’s Manual
Using Libraries
179
Output Patch Library
The Output Patch library enables you to store and recall all Output Patch settings. The
library contains one preset memory and 32 user (readable & writable) memories.
To access the Output Patch library, press the DISPLAY ACCESS [PATCH] button repeatedly
until the Patch | Out LIB page appears.
For details on storing and recalling memories, see “General Library Operation” on
page 175.
The Output Patch preset memory #0 contains the following settings:
Slot output channels 1–8
Bus Outs 1–8
Slot output channels 9–16
Bus Outs 1–8
ADAT OUT channels 1–8
Bus Outs 1–8
OMNI OUT connectors 1–4
Aux Outs 1–4
Effects Library
The Effects library enables you to store and recall Effects processor 1–4 programs. The
library contains 53 preset programs (including Add-On Effects) and 75 user (readable &
writable) programs.
Note: The Effects library is shared by Effects processors 1–4. However, only Effects processors
1 and 2 enable the recall of Effect 19 “HQ Pitch” and Effect 42 “Freeze.”
01V96 Version 2—Owner’s Manual
16
Libraries
To store and recall settings to and from the library, you must locate the corresponding
Effects processor’s page.
To access the Effects library, press the DISPLAY ACCESS [EFFECT] button repeatedly until
the library page for the desired Effects processor appears.
Each Effects processor features the library pages listed below:
• Internal Effects Processor 1 Library............FX1 Lib page
• Internal Effects Processor 2 Library............FX2 Lib page
• Internal Effects Processor 3 Library............FX3 Lib page
• Internal Effects Processor 4 Library............FX4 Lib page
180
Chapter 16—Libraries
1
2
5
3
4
A EFFECT NAME
This parameter displays the name of the Effects program currently selected by the
Effects processor.
B TYPE
This parameter displays the effects type currently used by the Effects processor. The
number of input and output channels for the currently-used effects appears below the
TYPE parameter.
C
Move the cursor to this button, then press [ENTER] to display the Effect | FX1 Edit, FX2
Edit, FX3 Edit, or FX4 Edit page to adjust the Effects parameters.
D
Move the cursor to this button, then press [ENTER] to display the In Patch | Effect page
to assign the input and output signals of Effects processors 1–4.
E Level meters
These meters indicate the input or output levels of the currently-selected Effects processor. Select the IN button or OUT button to display the input levels or output levels
respectively.
For details on storing and recalling programs, see “General Library Operation” on page 175.
01V96 Version 2—Owner’s Manual
Using Libraries
181
The following tables list the preset effects programs in the Effects library:
• Reverbs
No.
Preset Name
Type
Description
1
Reverb Hall
REVERB HALL
Concert hall reverberation simulation with gate
2
Reverb Room
REVERB ROOM
Room reverberation simulation with gate
3
Reverb Stage
REVERB STAGE
Reverb designed for vocals, with gate
4
Reverb Plate
REVERB PLATE
Plate reverb simulation with gate
5
Early Ref.
EARLY REF.
Early reflections without the subsequent reverb
6
Gate Reverb
GATE REVERB
Gated early reflections
7
Reverse Gate
REVERSE GATE
Gated reverse early reflections
• Delays
No.
Preset Name
Type
Description
8
Mono Delay
MONO DELAY
Simple mono delay
9
Stereo Delay
STEREO DELAY
Simple stereo delay
10
Mod.delay
MOD.DELAY
Simple repeat delay with modulation
11
Delay LCR
DELAY LCR
3-tap (left, center, right) delay
12
Echo
ECHO
Stereo delay with crossed left/right feedback
• Modulation-based Effects
No.
Preset Name
Type
Description
13
Chorus
CHORUS
Chorus
14
Flange
FLANGE
Flanger
15
Symphonic
SYMPHONIC
Proprietary Yamaha effect that produces a richer and
more complex modulation than normal chorus
16
Phaser
PHASER
16-stage stereo phase shifter
17
Auto Pan
AUTO PAN
Auto-panner
18
TREMOLO
TREMOLO
Tremolo
19
HQ.Pitch
HQ.PITCH
Mono pitch shifter, producing stable results (Available
for internal effects 1 and 2.)
20
Dual Pitch
DUAL PITCH
Stereo pitch shifter
21
Rotary
ROTARY
Rotary speaker simulation
22
Ring Mod.
RING MOD.
Ring modulator
23
Mod.Filter
MOD.FILTER
Modulated filter
16
No.
Preset Name
Type
Description
24
Distortion
DISTORTION
Distortion
25
Amp Simulate
AMP SIMULATE
Guitar amp simulation
• Dynamic Effects
No.
Preset Name
Type
Description
26
Dyna.Filter
DYNA.FILTER
Dynamically controlled filter
27
Dyna.Flange
DYNA.FLANGE
Dynamically controlled flanger
28
Dyna.Phaser
DYNA.PHASER
Dynamically controlled phase shifter
01V96 Version 2—Owner’s Manual
Libraries
• Guitar Effects
182
Chapter 16—Libraries
• Combination Effects
No.
Preset Name
Type
Description
29
Rev+Chorus
REV+CHORUS
Reverb and chorus in parallel
30
Rev->Chorus
REV->CHORUS
Reverb and chorus in series
31
Rev+Flange
REV+FLANGE
Reverb and flanger in parallel
32
Rev->Flange
REV->FLANGE
Reverb and flanger in series
33
Rev+Sympho.
REV+SYMPHO.
Reverb and symphonic in parallel
34
Rev->Sympho.
REV->SYMPHO.
Reverb and symphonic in series
35
Rev->Pan
REV->PAN
Reverb and auto-pan in series
36
Delay+ER.
DELAY+ER.
Delay and early reflections in parallel
37
Delay->ER.
DELAY->ER.
Delay and early reflections in series
38
Delay+Rev
DELAY+REV
Delay and reverb in parallel
39
Delay->Rev
DELAY->REV
Delay and reverb in series
40
Dist->Delay
DIST->DELAY
Distortion and delay in series
• Others
No.
Preset Name
Type
Description
41
Multi.Filter
MULTI.FILTER
3-band parallel filter (24 dB/octave)
42
Freeze
FREEZE
Simple sampler (Available for internal effects 1 and 2.)
43
Stereo Reverb
ST REVERB
Stereo reverb
44
M.Band Dyna.
M.BAND DYNA.
3-band dynamics processor
• Add-On Effects
No.
Preset Name
Type
451
Comp276
COMP276
461
Comp276S
COMP276S
471
Comp260
COMP260
481
Comp260S
COMP260S
491
Equalizer601
EQUALIZER601
501
OpenDeck
OPENDECK
511
REV-X Hall
REV-X HALL
521
REV-X Room
REV-X ROOM
531
REV-X Plate
REV-X PLATE
Description
—
1. These preset programs are dedicated to Add-On Effects. The numbers of effects programs that do not
have Add-On Effects installed are grayed out and cannot be used. For more information on Add-On
Effects, refer to “About Add-On Effects” on page 162.
01V96 Version 2—Owner’s Manual
Using Libraries
183
Gate Library
The Gate library enables you to store and recall Input Channel gate settings. The library
contains four preset memories and 124 user (readable & writable) memories.
Follow the steps below to use the Gate library.
1 Press the DISPLAY ACCESS [DYNAMICS] button, then press the [F2] button.
The Dynamics | Gate Lib page appears.
1
2
3
4
A CURRENT TYPE
This parameter displays the currently-selected channel gate type (Gate or Ducking).
B CURRENT CURVE
This graph displays the current channel gate curve.
C GR meters
These meters indicate the amount of gain reduction being applied by the gate, and the
post-gate levels of the currently-selected channel and its available pair partner.
D Type & Curve section
The type (Gate or Ducking) and curve of the currently-selected memory is displayed
here.
Tip: If you selected an ST IN Channel (1–4), Aux Out (1–8), Bus Out (1–8), or Stereo Out
that does not feature a gate, the 01V96 indicates “XXX has no Gate!” (in which XXX represents
a channel name).
No.
Preset Name
Type
Description
1
Gate
GATE
Gate template
2
Ducking
DUCKING
Ducking template
3
A. Dr. BD
GATE
Gate preset for use with acoustic bass drums
4
A. Dr. SN
GATE
Gate preset for use with acoustic snare drums
01V96 Version 2—Owner’s Manual
16
Libraries
2 Use the LAYER buttons to select layers, then press the [SEL] buttons to select
channels.
You can now store the selected channel gate settings or recall the gate library memories to
channels. For details on storing and recalling memories, see “General Library Operation”
on page 175.
The following table lists the preset memories in the Gate library:
184
Chapter 16—Libraries
Compressor Library
This library enables you to store and recall settings for the compressors on Input Channels,
Bus Outs 1–8, Aux Outs 1–8, and Stereo Out. The library contains 36 preset memories and
92 user (readable & writable) memories.
Follow the steps below to use the Compressor library.
1 Press the DISPLAY ACCESS [DYNAMICS] button, then press the [F4] button.
The Dynamics | Comp Lib page appears.
1
2
3
4
A CURRENT TYPE
This parameter displays the currently-selected channel comp type (Compressor,
Expander, Compander Soft, Compander Hard).
B CURRENT CURVE
This graph displays the current compressor curve.
C GR meters
These meters indicate the amount of gain reduction being applied by the compressor,
and the post-comp levels of the currently-selected channel and its available pair partner.
D Type & Curve section
The type and curve of the currently-selected memory is displayed here.
2 Use the LAYER buttons to select layers, then press the [SEL] buttons to select
channels.
You can now store the selected channel comp settings and recall the compressor library
memories to channels. For details on storing and recalling memories, see “General Library
Operation” on page 175. Since ST IN Channels do not feature compressors, if you select an
ST IN Channel, the message “Stereo in has no Comp!” appears on the display.
01V96 Version 2—Owner’s Manual
Using Libraries
185
The following table lists the preset memories in the Compressor library:
No.
Preset Name
Type
Description
Comp
COMP
Compressor for reducing the overall volume level. Use
it on the stereo output during mixdown, or with paired
Input or Output Channels.
2
Expand
EXPAND
Expander template.
3
Compander (H)
COMPAND-H
Hard-kneed compressor template.
4
Compander (S)
COMPAND-S
Soft-kneed compressor template.
5
A. Dr. BD
COMP
Compressor for use with acoustic bass drum.
6
A. Dr. BD
COMPAND-H
Hard-kneed compander for use with acoustic bass
drum.
7
A. Dr. SN
COMP
Compressor for use with acoustic snare drum.
8
A. Dr. SN
EXPAND
Expander for use with acoustic snare drum.
9
A. Dr. SN
COMPAND-S
Soft-kneed compander for use with acoustic snare
drum.
10
A. Dr. Tom
EXPAND
Expander for use with acoustic tom toms, which automatically reduces the volume when the tom toms are
not played, improving mic separation.
11
A. Dr. OverTop
COMPAND-S
Soft-kneed compander for emphasizing the attack and
ambience of cymbals recorded with overhead mics. It
automatically reduces the volume when the cymbals
are not played, improving mic separation.
12
E. B. Finger
COMP
Compressor for leveling the attack and volume of a finger-picked electric bass guitar.
13
E. B. Slap
COMP
Compressor for leveling the attack and volume of a
slapped electric bass guitar.
14
Syn. Bass
COMP
Compressor for controlling or emphasizing the level of
a synth bass.
15
Piano1
COMP
Compressor for brightening the tonal color of a piano.
16
Piano2
COMP
A variation on preset 15, using a deep threshold to
change the overall attack and level.
17
E. Guitar
COMP
Compressor for electric guitar “cutting” or arpeggio-style backing. The sound color can be varied by
playing different styles.
18
A. Guitar
COMP
Compressor for acoustic guitar “stroke” or arpeggio-style backing.
19
Strings1
COMP
Compressor for use with strings.
20
Strings2
COMP
A variation on preset 19, intended for violas or cellos.
21
Strings3
COMP
A variation on preset 20, intended for string instruments with a very low range, such as cellos or contrabass.
22
BrassSection
COMP
Compressor for brass sounds with a fast and strong
attack.
23
Syn. Pad
COMP
Compressor for musical instruments that feature gentle
sounds which, depending on the tones, could diffuse,
such as synth pad. Intended to prevent diffusion of the
sound.
24
SamplingPerc
COMPAND-S
Compressor for making sampled percussion sound like
real acoustic percussion.
25
Sampling BD
COMP
A variation on preset 24, intended for sampled bass
drum sounds.
26
Sampling SN
COMP
A variation on preset 25, intended for sampled snare
drum sounds.
27
Hip Comp
COMPAND-S
A variation on preset 26, intended for sampled loops
and phrases.
28
Solo Vocal1
COMP
Compressor for use with main vocals.
29
Solo Vocal2
COMP
A variation on preset 28.
30
Chorus
COMP
A variation on preset 28, intended for choruses.
01V96 Version 2—Owner’s Manual
16
Libraries
1
186
Chapter 16—Libraries
No.
Preset Name
Type
Description
31
Click Erase
EXPAND
Expander for removing a click track that may bleed
through from a musician’s headphones.
32
Announcer
COMPAND-H
Hard-kneed compander for reducing the level of the
music when an announcer speaks.
33
Limiter1
COMPAND-S
A soft-kneed compander with a slow release.
34
Limiter2
COMP
A “peak-stop” compressor.
35
Total Comp1
COMP
Compressor for reducing the overall volume level. Use
it on the stereo output during mixdown, or with paired
Input or Output Channels.
36
Total Comp2
COMP
A variation on preset 35, but with more compression.
EQ Library
This library enables you to store and recall EQ settings for Input Channels, Bus Outs 1–8,
Aux Outs 1–8, and Stereo Out. The library contains 40 preset memories and 160 user (readable & writable) memories.
Follow the steps below to use the EQ library.
1 Press the DISPLAY ACCESS [EQ] button, then press the [F2] button.
The EQ | EQ Library page appears.
1
2
3
4
A CURRENT TYPE
This parameter displays the currently-selected channel EQ type (TYPE I or II).
B CURRENT CURVE
This graph displays the current EQ curve.
C Level meters
These meters indicate the post-EQ levels of the currently-selected channel and its available pair partner.
D Type & Curve section
The type and curve of the currently-selected EQ program are displayed here.
2 Use the LAYER buttons to select layers, then press the [SEL] buttons to select
channels.
You can now store the selected channel EQ settings or recall the EQ library memories to
channels. For details on storing and recalling memories, see “General Library Operation”
on page 175.
01V96 Version 2—Owner’s Manual
Using Libraries
187
The following table lists the preset memories in the EQ library:
No.
Preset Name
Description
1
Bass Drum 1
Emphasizes the low range of a bass drum and the attack created by the
beater.
2
Bass Drum 2
Creates a peak around 80 Hz, producing a tight, stiff sound.
3
Snare Drum 1
Emphasizes “snappy” and rimshot sounds.
4
Snare Drum 2
Emphasizes various ranges for that classic rock snare drum sound.
5
Tom-tom 1
Emphasizes the attack of tom-toms, and creates a long, “leathery” decay.
6
Cymbal
Emphasizes the attack of crash cymbals, extending the “sparkling” decay.
7
High Hat
Use on a tight high-hat, emphasizing the mid to high range.
8
Percussion
Emphasizes attack and adds clarity to the high-range of instruments, such
as shakers, cabasas, and congas.
E. Bass 1
Produces a tight electric bass sound by cutting very low frequencies.
E. Bass 2
Unlike preset 9, this preset emphasizes the low range of an electric bass.
11
Syn. Bass 1
Use on a synth bass with emphasized low range.
12
Syn. Bass 2
Emphasizes the attack that is peculiar to synth bass.
13
Piano 1
Makes pianos sound brighter.
14
Piano 2
Used in conjunction with a compressor, this preset emphasizes the attack
and low range of pianos.
15
E. G. Clean
Use for line-level recording of an electric or semi-acoustic guitar to get a
slightly harder sound.
16
E. G. Crunch 1
Adjusts the tonal quality of a slightly distorted guitar sound.
17
E. G. Crunch 2
A variation on preset 16.
18
E. G. Dist. 1
Makes a heavily distorted guitar sound clearer.
19
E. G. Dist. 2
A variation on preset 18.
20
A. G. Stroke 1
Emphasizes the bright tones of acoustic guitars.
21
A. G. Stroke 2
A variation on preset 20. You can also use it with an acoustic-electric nylon
string guitar.
22
A. G. Arpeg. 1
Ideal for arpeggio playing on acoustic guitars.
23
A. G. Arpeg. 2
A variation on preset 22.
24
Brass Sec.
Use with trumpets, trombones, or saxes. When used with a single instrument, try adjusting the HIGH or HIGH-MID frequency.
25
Male Vocal 1
An EQ template for male vocals. Try adjusting the HIGH or HIGH-MID
parameters according to the voice quality.
26
Male Vocal 2
A variation on preset 25.
27
Female Vo. 1
An EQ template for female vocals. Try adjusting the HIGH or HIGH-MID
parameters according to the voice quality.
28
Female Vo. 2
A variation on preset 27.
29
Chorus&Harmo
An EQ template for brightening choruses.
30
Total EQ 1
Use on a stereo mix during mixdown. Sounds even better when used with a
compressor.
31
Total EQ 2
A variation on preset 30.
32
Total EQ 3
A variation on preset 30. Can also be used with paired Input or Output
Channels.
33
Bass Drum 3
A variation on preset 1, with low and mid range reduced.
34
Snare Drum 3
A variation on preset 3, creating a thicker sound.
35
Tom-tom 2
A variation on preset 5, emphasizing the mid and high ranges.
36
Piano 3
A variation on preset 13.
37
Piano Low
Emphasizes the low range of pianos recorded in stereo.
38
Piano High
Emphasizes the high range of pianos recorded in stereo.
39
Fine-EQ Cass
Add clarity when recording to or from cassette tape.
40
Narrator
Ideal for recording narration.
01V96 Version 2—Owner’s Manual
16
Libraries
9
10
188
Chapter 16—Libraries
01V96 Version 2—Owner’s Manual
Remote Control
189
17 Remote Control
This chapter describes the Remote function, which enables you to control external equipment directly from the 01V96 top panel.
About Remote Function
The 01V96’s Remote function enables you to control external DAW (Digital Audio Workstation) equipment, MIDI devices, recorders, etc.
There are two types of Remote functions (Remote and Machine Control):
■ REMOTE (Remote Layer)
To use these types of Remote functions, you must connect the 01V96 to a target device via
USB or an optional MY8-mLAN card installed in the slot, and operate the faders and [ON]
buttons on the top panel to control the external device remotely.
You can specify a target device and parameter values on the DIO/Setup | Remote page. This
layer is enabled when you turn on the LAYER [REMOTE] button. During Remote operation, the controls on the top panel enable you to control the external device. (You cannot
adjust the 01V96’s parameters unless you select a different layer.)
You can assign functions of a target device to the controls on the top panel of the 01V96 by
using Remote layer. The following targets are available for remote control:
• ProTools ........................You can remotely control Digidesign Pro Tools.
• Nuendo..........................You can remotely control Steinberg Nuendo.
• Cubase SX .....................You can remotely control Steinberg Cubase SX.
• General DAW................You can remotely control DAW software that supports the protocol used by Pro Tools.
• User Defined.................You can also assign MIDI messages to the faders or [ON] buttons to remotely control a connected MIDI device, such as a
synthesizer.
• User Assignable Layer.......You can combine the 01V96 channels to create a custom
layer. (See page 233 for more information on this function.)
■ Machine Control
By using MIDI Machine Control commands and the DIO/Setup | Machine page, you can
control an external recording machine that is connected to the 01V96 MIDI port, USB port,
or optional MY8-mLAN card installed in the slot.
Tip: To control external devices from the 01V96, you can also use the User Defined buttons.
Refer to “19 Other Functions” for more information.
17
Remote Control
01V96 Version 2—Owner’s Manual
190
Chapter 17—Remote Control
Pro Tools Remote Layer
The 01V96 features Remote Layer target especially designed for controlling Pro Tools.
Connections and Configuring Pro Tools
Follow the steps below to connect the 01V96 to your computer via the USB port so that you
can control Pro Tools from the 01V96.
Note: You cannot control Pro Tools via MIDI connections. Be sure to connect your computer
via the USB or an optional MY8-mLAN card installed in the 01V96 slot.
■ Configuring Windows Computers
1 Connect the 01V96 TO HOST USB port to a USB port on your PC using a USB
cable.
TO HOST USB port
USB
CH1-4
1
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
CH9-12
PHANTOM +48V
L
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
14
16
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
CH15/16
2TR IN
INSERT I/O
MONITOR
2TR IN
PAD
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-16
-60
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DIO/SETUP
-60
GAIN
DISPLAY ACCESS
SCENE
-16
PEAK
SIGNAL
13
PEAK
14 15
SIGNAL
LEVEL
10
PEAK
16
SIGNAL
SCENE MEMORY
MIDI
UTILITY
PAIR/
GROUP
PATCH
EFFECT
VIEW
STORE
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
0
-3
PAN
-6
EQ
DYNAMICS
DEC
INC
-9
-12
FADER MODE
-15
EQUALIZER
-18
-24
-30
AUX 1
AUX 2
AUX 3
AUX 4
AUX 7
AUX 8
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
HIGH-MID
FREQUENCY
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
+10
0 +10
5
0 +10
5
15
15
30 15
30 15
20
40 20
40 20
30
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
1
2
15
20 10
3
15
15
15
15
15
10
5
15
10
5
15
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
4
5
6
7
8
9
20 10
10
20 10
11
15
20 10
12
5
0
10
5
20 10
5
10
10
15
15
20
30 15
30 15
30
30
40 20
40 20
40
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
30 15
30 15
40 20
50 30
60 40
70
50
14
0
5
20
10
5
40 20
13
0
20 10
15
20 10
SEL
SOLO
ON
ON
ST IN 1
0
10
5
20 10
SEL
SOLO
ON
ST IN 2
Computer
5
5
0
10
5
20 10
0 +10
5
5
0
20 10
20 10
0 +10
5
5
0
20 10
20 10
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
5
0 +10
5
5
0
10
15
40
20 10
5
20 10
0 +10
5
5
0
10
5
10
0 +10
5
5
0
10
5
0 +10
5
5
0
10
15
0 +10
5
5
0
5
0 +10
5
5
0
SEL
15
15
5
40
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
2 Install the necessary USB drivers included on the 01V96 CD-ROM.
See the Studio Manager Installation Guide for more information on installing the drivers.
■ Configuring Macintosh Computers
1 Connect the 01V96 TO HOST USB port to a USB port on your Mac using a
USB cable.
2 Install the required USB driver included on the 01V96 CD-ROM.
See the Studio Manager Installation Guide for more information on installing the driver.
3 If you are using Mac OS versions 8.6 through 9.2.2, install OMS.
The 01V96 communicates with Pro Tools via OMS (Open Music System) software.
If you have not installed OMS on your Mac, use the OMS installer included on the 01V96
CD-ROM to install OMS.
4 Launch Pro Tools.
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
191
5 If you are using Mac OS versions 8.6 through 9.2.2, choose OMS Studio Setup
from the Setups menu, and configure OMS as necessary.
Refer to the documentation
that came with OMS for more
information on configuring
the OMS Studio Setup menu.
OMS recognizes the 01V96 as
a USB MIDI interface that features eight ports.
6 Choose Peripherals from the Setups menu to open the Peripherals window.
7 Double-click the MIDI Controllers tab.
8 Refer to the screen below to set the Type, Receive From, Send To, and #Ch’s
parameters.
The 01V96 can emulate up to two MIDI controllers.
17
9 When you finish setting the parameters, close the window.
01V96 Version 2—Owner’s Manual
Remote Control
Tip: To control Pro Tools remotely, you need one port for every eight audio channels.
192
Chapter 17—Remote Control
Configuring the 01V96
Follow the steps below to set up the 01V96 so that you can remotely control Pro Tools from
the 01V96 Remote Layer.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | MIDI/Host page appears.
2 Move the cursor to the first DAW parameter box in the SPECIAL FUNCTIONS
section, then rotate the Parameter wheel to select USB as the port.
3 Press [ENTER] to confirm the setting.
4 Move the cursor to the adjacent
parameter box (on the right), then
rotate the Parameter wheel to specify the port ID.
Note: If you select an incorrect port, you will be unable to use the Remote function. Be sure
to match the port ID with that specified in the Peripherals window in Pro Tools.
5 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Remote page appears.
1
6 Select ProTools (as the target device) for the Target parameter (1) located
in the upper-right corner of the page.
By default, the Remote layer target is set to ProTools. If another target has been selected,
rotate the Parameter wheel to select ProTools.
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
193
7 Press the LAYER [REMOTE] button.
The Remote Layer is now available for control, enabling you to remotely control Pro Tools.
Note: When the Pro Tools Remote layer is selected, the 01V96’s top panel faders and other
channel buttons are available for remote control. To control the 01V96, you need to select an
Input Channel Layer or the Master Layer.
Display
While the Pro Tools layer is selected, you can use the [F2]–[F4] buttons as well as the left
and right [ ]/[ ] Tab Scroll buttons to select display modes. You can select the following display modes using these buttons:
■ Insert Display mode ( [F2] button)
Press the [F2] button to select Insert Display mode. In this mode, you can assign and edit
plug-ins.
1
2
3
4
5
17
This parameter enables you to select the remote control target device.
B COUNTER
This counter indicates the current position. This counter works in unison with the timecode counter on Pro Tools. The display format of the counter is specified in Pro Tools.
The following three check boxes in the COUNTER section indicate the currently-selected format.
• TIME CODE: ................Pro Tools timecode format is set to “Time Code.”
• FEET: .............................Pro Tools timecode format is set to “Feet:Frames.”
• BEATS:...........................Pro Tools timecode format is set to “Bars:Beats.”
01V96 Version 2—Owner’s Manual
Remote Control
A TARGET
194
Chapter 17—Remote Control
• If no check boxes are selected:...........Pro Tools timecode format is set to “Minutes:Seconds” or “Samples.”
C SELECT ASSIGN
This parameter indicates the current parameter, which can be adjusted via the parameter controls on the page. For example, Pan, PanR, SndA, SndB, SndC, SndD, or SndE
(see page 196).
D P.WHEEL MODE
This parameter indicates the function currently assigned to the Parameter wheel (see
page 197).
E INSERT ASSIGN/EDIT section
This section enables you to insert plug-ins into Pro Tools channels and adjust plug-in
settings. Use the left and right [ ]/[ ] Tab Scroll buttons to change the parameters
displayed in this section.
• ASSIGN ......................... Turn on this button to insert plug-ins into Pro Tools channels.
(If you are using the TDM system, you can also assign outboard
effects processors.)
• COMPARE.................... You can compare your edits with the original settings by turning on this button. This button works in unison with the Compare button in the Pro Tools Inserts and Sends windows.
• BYPASS ......................... Turning on this button bypasses the plug-ins (see page 204).
• INSERT/PARAM.......... Switching this button to INSERT enables you to assign plug-ins
using four rotary controls on the page. Switching this button to
PARAM enables you to adjust the plug-in parameters using the
four rotary controls (see page 203).
• Information box.......... This box displays plug-in parameter names, values, alarm messages from Pro Tools, etc.
• Rotary controls 1–4..... These controls enable you to select plug-ins or adjust the
selected plug-in parameters.
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
195
■ Channel Display mode ( [F3] button)
Press the [F3] button to select this display mode, in which the parameter controls for tracks
1–16 are displayed.
• Parameter controls 1–16 ................... Channel parameter controls, such as channel
1–16 panpots, Send A–E send levels, etc. are displayed.
■ Meter Display mode ( [F4] button)
Press the [F4] button to select this display mode, in which the level meters for tracks 1–16
are displayed.
• Channels 1–16..............The channel 1–16 levels or Send levels are displayed.
17
Remote Control
01V96 Version 2—Owner’s Manual
196
Chapter 17—Remote Control
Control Surface Operation
When the Pro Tools Remote layer is selected, the 01V96 controls on the top panel engage
the following functions:
■ Channel Strip section
• [SEL] buttons
These buttons select Pro Tools channels, inserts, and Automation mode.
• [SOLO] buttons
These buttons solo Pro Tools channels. The button indicators for the soloed channels light
up.
• [ON] buttons
These buttons mute Pro Tools channels.
• Faders
The faders set Pro Tools channel levels, including the audio tracks, MIDI tracks, master
fader, Aux Ins, etc. If 16 or fewer channels are displayed in Pro Tools, faders are assigned
starting from the left-most channel.
■ FADER MODE Section
• [AUX 1]–[AUX 5] buttons
These buttons select Sends A–E so that you can adjust the corresponding Pro Tools channel
send level.
• [AUX 6] button
Press and hold down this button and press the desired [SEL] button to reset the corresponding channel fader level.
Move the cursor to the parameter control on the display, then press and hold down this button and press [ENTER] to reset the corresponding channel panpot to center. While you are
holding down the [AUX 6] button, the SELECT ASSIGN parameter indicates “DFLT.”
• [AUX 7] button
When this button is turned on, you can adjust the selected channel panpot using the
SELECTED CHANNEL [PAN] control. If you turn on this button while a Channel Display
mode page is selected, you can adjust each channel panpot using parameter controls 1–16.
To adjust the stereo channel panpots, press this button repeatedly to toggle between L and
R channels.
• [AUX 8] button
Use this button along with the desired [SEL] button to assign a plug-in to the corresponding
Pro Tools channel (see page 202).
• [HOME] button
This button turns Flip mode (see page 201) on or off. Flip mode enables you to adjust the
Aux Send parameters using the faders, [ON] buttons, and the [PAN] control.
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
197
■ DISPLAY ACCESS section
• [PAIR/GROUP] button
Press this button while a Channel Display mode or Meter Display mode page is selected to
display a Group ID to which each channel belongs.
• [EFFECT] button
Press this button to display or hide the Insert window in Pro Tools.
■ Display section
• [F1] button
Press this button to reset the Clipping and Peak Hold indicators on Meter Display mode
pages.
• Tab Scroll buttons ([ ]/[ ])
These buttons switch the INSERT ASSIGN/EDIT parameter settings on Insert Display
mode pages.
■ Data Entry section
• [ENTER] button
This button switches the on/off status of the buttons on the display.
• Left, Right, Up, Down ([ ]/[ ]/[ ]/[ ]) cursor buttons
These buttons move the cursor on the display.
• [INC] & [DEC] buttons
The [INC] button works the same as the Enter key on your computer keyboard. The [DEC]
button works the same as the Esc key on your computer keyboard.
• Parameter wheel
The Parameter wheel enables you to adjust the currently-selected parameter, or execute the
shuttle and scrub operation. By default, it adjusts the value of the currently-selected parameter (The P.WHEEL MODE parameter indicates “Prm.”).
■ USER DEFINED KEYS section
• [1]–[8] buttons
You can assign one of 194 parameters to each of these buttons. In particular, if you assign
any of 54 Remote Control parameters to these buttons, you can operate the transport section and select various Pro Tools modes from the 01V96 top panel. See page 235 for more
information on assigning the parameters to the buttons.
Function
DAW REC
Places Pro Tools in Record Enabled mode. The button indicator flashes while
the transport section is stopped. The indicator lights up when recording starts.
DAW PLAY
Starts playback from the current cursor position.
DAW STOP
Stops playback and recording.
DAW FF
Fast forwards the cursor position.
DAW REW
Fast rewinds the cursor position.
DAW SHUTTLE
Switches the Wheel mode to Shuttle.
DAW SCRUB
Switches the Wheel mode to Scrub (Jog).
DAW AUDITION
You can audition the pre-roll, post-roll, in-point area, or out-point area by
holding down the button to which this function is assigned and pressing a
button to which DAW PRE, DAW POST, DAW IN, or DAW OUT is assigned.
01V96 Version 2—Owner’s Manual
17
Remote Control
Parameter
198
Chapter 17—Remote Control
Parameter
Function
DAW PRE
Plays back from the pre-roll point up to the beginning of the selected area.
DAW IN
Plays back from the beginning of the selected area for a duration specified as
the pre-roll.
DAW OUT
Plays back to the end of the selected area for a duration specified as the
post-roll.
DAW POST
Plays back from the end of the selected area for a duration specified as the
post-roll.
DAW RTZ
Moves the playback cursor to the beginning of the session.
DAW END
Moves the playback cursor to the end of the session.
DAW ONLINE
Toggles between on-line and off-line.
DAW LOOP
Toggles Loop Playback on and off.
DAW QUICKPUNCH
Toggles QuickPunch on and off.
DAW AUTO FADER
DAW AUTO MUTE
DAW AUTO PAN
DAW AUTO SEND
Correspond to the Automation Overwrite (Auto Enable) functions.
DAW AUTO PLUGIN
DAW AUTO SENDMUTE
DAW AUTO READ
DAW AUTO TOUCH
DAW AUTO LATCH
DAW AUTO WRITE
Select Automation modes.
DAW AUTO TRIM
DAW AUTO OFF
DAW AUTO SUSPEND
Cancels Automation recording and playback for all channels. When Automation is interrupted, the LED flashes, and channel strip controls maintain the
current settings.
DAW AUTO STATUS
Displays the channel Automation mode (Read, Tch, Ltch, Wrt, or Off). The
mode setting appears at the bottom of each channel on a Channel or Meter
Display page when you press and hold the button to which this function is
assigned.
DAW GROUP STATUS
Displays a Group ID (to which each channel belongs) below each channel
number on a Channel or Meter Display page (in all caps for a main group and
in lowercase letters for a sub-group).
DAW MONI STATUS
Pressing the key (to which this function is assigned) enables you to view the
current monitoring mode and the channel strip type.
DAW CREATE GROUP
Pressing the key (to which this function is assigned) enables you to execute
the function specified in the menu of the Pro Tools Group list.
DAW SUSPEND GROUP
Suspends all mix groups temporarily. Press the button again to undo suspension.
DAW WIN TRANSPORT
Shows or hides the Transport window.
DAW WIN INSERT
Shows or hides the Insert window.
DAW WIN MIX/EDIT
Toggles between the Mix window and Edit window. (Both windows are not
displayed at the same time.)
DAW WIN MEM-LOC
Shows or hides the Memory Locations window.
DAW WIN STATUS
Shows or hides the Status window.
DAW UNDO
Executes the Edit menu’s Undo/Redo command.
DAW SAVE
Executes the Edit menu’s Save command.
DAW EDIT MODE
Pressing the button (to which this function is assigned) repeatedly selects
Shuffle, Slip, Spot, or Grid edit mode in this order.
DAW EDIT TOOL
Pressing the button (to which this function is assigned) repeatedly selects one
of seven edit tools (Zoomer, Trimmer, Selector, Grabber, Smart Tool, Scrubber,
and Pencil, in this order).
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
Parameter
DAW SHIFT/ADD
DAW OPTION/ALL
DAW CTRL/CLUCH
DAW ALT/FINE
DAW BANK +
DAW BANK –
DAW Channel +
DAW Channel –
199
Function
Functions in the same way as Macintosh keyboard keys (Shift, Option, Control, and Alt). Pressing one of the buttons (to which these functions are
assigned) along with another button enables you to execute various commands.
Executes the Bank Swap operation. Pressing the button (to which this function
is assigned) switches the entire 16-channel bank.
Executes the Channel Scroll operation. Pressing the buttons (to which these
functions are assigned) enables you to scroll channels horizontally.
DAW REC/RDY 1
DAW REC/RDY 2
DAW REC/RDY 3
DAW REC/RDY 4
DAW REC/RDY 5
DAW REC/RDY 6
DAW REC/RDY 7
DAW REC/RDY 8
DAW REC/RDY 9
Pressing the buttons (to which these functions are assigned) places the corresponding channel strips in Record Ready mode. At this time, the indicator of
the button you pressed flashes. It lights up when recording starts.
DAW REC/RDY 10
DAW REC/RDY 11
DAW REC/RDY 12
DAW REC/RDY 13
DAW REC/RDY 14
DAW REC/RDY 15
DAW REC/RDY 16
DAW REC/RDY ALL
If no channel strips are in Record Enabled mode, pressing the button (to
which this function is assigned) places all channel strips in Record Enabled
mode. The button indicator flashes if any channel strip in any bank is in
Record Enabled mode. Pressing the button while the button indicator is flashing cancels Record Enabled mode for all channel strips.
Selecting Channels
To select a single Pro Tools channel, press the [SEL] button that corresponds to the desired
channel.
To select multiple Pro Tools channels simultaneously, while holding down one [SEL] button, press the [SEL] buttons of the other channels you wish to add. Press the [SEL] buttons
again to cancel the selection.
1 Make sure that the FADER MODE [HOME] button indicator is lit steadily.
If the indicator is flashing, press the [HOME] button to turn on the button indicator.
2 Operate the faders to set channel levels.
Press and hold down the [AUX 6] button and press the desired [SEL] button to reset the
corresponding channel fader level.
01V96 Version 2—Owner’s Manual
17
Remote Control
Setting Channel Levels
200
Chapter 17—Remote Control
Muting Channels
To mute Pro Tools channels, press the [ON] buttons. The [ON] button indicators of muted
channels turn off. Grouped channels are muted together.
Press the [ON] buttons again to unmute channels. The [ON] button indicators of unmuted
channels light up.
There are two mute modes in Pro Tools: Implicit mute and Explicit mute. You can check the
mute mode by viewing the [ON] button indicators.
• Implicit mute ............... This is a forced mute mode in which the channels are muted
because other channels are soloed. In this mode, the [ON] button indicators flash.
• Explicit mute................ In this mode, the channels are turned off manually. In this
mode, the [ON] button indicators turn off.
Panning Channels
You can adjust the Pro Tools channel pan settings.
1 Press the FADER MODE [AUX 7] button.
The button indicator lights up.
2 Press the [F3] button to select Channel Display mode.
On a Channel Display mode page, parameter controls 1–16 indicate the pan settings.
3 Press the [SEL] button of the channel for which you want to adjust the pan
setting.
To adjust the stereo channel panpots, press the STEREO [SEL] button, then press the [AUX
7] button to select the L or R channel. Pressing the [AUX 7] button repeatedly toggles
between the left and right channels. When the left channel is selected, the [AUX 7] button
indicator lights up and the SELECT ASSIGN parameter on the display indicates “Pan.”
When the right channel is selected, the [AUX 7] button indicator flashes and the SELECT
ASSIGN parameter indicates “PanR.”
Note: Before you adjust monaural channel panpots, first be sure the [AUX 7] button indicator
is illuminated steadily. If the indicator is flashing, operating the [PAN] control will be ineffective.
4 Adjust the selected channel panpot using the SELECTED CHANNEL [PAN]
control.
5 To reset the corresponding channel panpot to center, move the cursor to
the parameter control on the display, then press and hold down the [AUX
6] button and press [ENTER].
You can reset the pan settings only when the [AUX 7] button indicator is lit steadily.
Soloing Channels
To solo Pro Tools channels, press the [SOLO] buttons of the desired channels. Grouped
channels are soloed together, and other channels are muted.
Press the [SOLO] buttons again to unsolo the channels.
Configuring Sends A–E as Pre or Post
You can set Pro Tools channels for the selected Sends (A–E) to pre or post.
1 Press the [F3] button to select Channel Display mode.
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
201
2 Press the FADER MODE [AUX 1]–[AUX 5] buttons to select the desired Sends
(A–E).
3 To toggle between pre and post, move the cursor to the parameter control
on the display, then press [ENTER].
Pressing [ENTER] repeatedly toggles between pre and post.
Setting Send Levels
You can adjust Pro Tools Send (A–E) send levels as follows.
1 Press the [F3] button to select Channel Display mode.
2 Press the AUX SELECT [AUX 1]–[AUX 5] buttons to select the desired Sends
(A–E).
3 Move the cursor to the parameter control of the channel for which you want
to adjust the Send level, then rotate the Parameter wheel.
You can set Send levels by operating the faders if faders, [ON] buttons, and the [PAN] control are in Flip mode. Refer to “Flip Mode” for more information.
Muting Sends A–E
You can mute Sends by pressing the [ON] buttons if faders, [ON] buttons, and the [PAN]
control are in Flip mode. Refer to “Flip Mode” for more information.
Panning Sends A–E
You can pan channel signals sent to stereo Aux Sends by rotating the SELECTED CHANNEL [PAN] control if faders, [ON] buttons, and the [PAN] control are in Flip mode. Refer
to the next section for more information.
Flip Mode
In Flip mode, you can use the faders, [ON] buttons, and the [PAN] control to control send
levels, pre/post positions, and mute settings as shown in the following table.
Control
Normal mode
Flip Mode
Faders
Channel level
AUX Send level
[ON] buttons
Channel mute
AUX Send mute
[PAN] control
Channel pan
AUX Send pan
1 Press the FADER MODE [HOME] button repeatedly so that the button indicator flashes.
The SELECT ASSIGN parameter on the display indicates “FLIP.”
3 Use the faders, [ON] buttons, and the [PAN] control to control the currently-selected Aux send.
For stereo Aux input channels, you can set the left and right panpots individually. To do this,
press the FADER MODE [AUX 7] button repeatedly. When the button indicator is lit continuously, you can set the left panpot. When the button indicator is flashing, you can set the
right panpot.
01V96 Version 2—Owner’s Manual
Remote Control
2 Press the FADER MODE [AUX 1]–[AUX 5] buttons to select the desired Aux
Sends (A–E).
The button indicator of the selected send lights up.
17
202
Chapter 17—Remote Control
Assigning Plug-ins to Pro Tools Channels
You can assign plug-ins to five inserts available for Pro Tools channel strips as follows.
1 Press the [F2] button to select Insert Display mode.
2 Press the FADER MODE [AUX 8] button.
The [AUX 8] button indicator flashes. You can now select a channel to which you want to
insert plug-ins.
3 Press the [SEL] button of each desired channel.
4 Make sure that the INSERT/PARAM button (1) is selected in the INSERT
ASSIGN/EDIT section.
If the PARAM button is selected instead, move the cursor to the button, then press
[ENTER] to select INSERT.
2
1
5 Move the cursor to the ASSIGN button (2), then press [ENTER] to turn on
the button.
You can now select plug-ins. If you press another channel’s [SEL] button after you turn on
the ASSIGN button, the button turns off. If you wish to assign plug-ins to other channels,
turn on the ASSIGN button again.
6 Move the cursor to one of the four parameter controls, then rotate the
Parameter wheel to select a plug-in.
By default, the parameter controls enable you to select plug-ins to be assigned to channel
inserts #1–#4. To assign a plug-in to insert #5, press the Tab Scroll button [ ] to change
the indication in the INSERT ASSIGN/EDIT section.
If you are using the TDM system, you can also assign outboard effects processors.
7 Press [ENTER] to confirm the assignment.
Repeat Steps 6 and 7 to assign more plug-ins to other insert positions in the channel strip.
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
203
8 In the same way, assign plug-ins to other channels.
9 When you finish assigning plug-ins, press the [AUX 8] button.
The button indicator turns off.
Editing Plug-ins
You can edit plug-ins inserted in the channel strips as follows:
1 Press the [F2] button to select Insert Display mode.
2 Press the corresponding [SEL] button to select the channel that was assigned
the plug-in you want to edit.
3 In the INSERT ASSIGN/EDIT section, move the cursor to the parameter control (Insert 1–4) that was assigned the parameter you want to edit.
Note: To adjust a plug-in assigned to insert #5, press the Tab Scroll button [ ] to change
the parameter indication in the INSERT ASSIGN/EDIT section, then select a parameter control.
4 Press [ENTER] to display the parameters.
In the INSERT ASSIGN/EDIT section, the PARAM button is automatically selected and the
Information box indicates the selected plug-in parameters.
You can now use parameter controls 1–4 and the [ENTER] button to adjust the parameters.
01V96 Version 2—Owner’s Manual
17
Remote Control
5 Use the Tab Scroll buttons to display the parameter value you wish to
change.
Most plug-ins feature five or more parameters. To edit the fifth or subsequent parameters,
use the Tab Scroll buttons to display the desired parameters and their values in the INSERT
ASSIGN/EDIT section. The current page number and the plug-in name appear for a
moment immediately after you press the Tab Scroll buttons.
204
Chapter 17—Remote Control
6 Move the cursor to a parameter control, then rotate the Parameter wheel
or press the [ENTER] button to adjust the value.
One or two parameters are assigned to a single parameter control. To turn the parameter
setting on or off, press [ENTER]. To modify the parameter variable, rotate the Parameter
wheel.
7 When you finish adjusting the parameters, move the cursor to the
INSERT/PARAM button, then press [ENTER] to switch it to INSERT.
Bypassing Plug-ins
You can bypass plug-ins assigned to Pro Tools channels.
Before bypassing plug-ins, you must press the corresponding [SEL] button to select a channel to which the plug-ins have been assigned, then press the [F2] button to select Insert Display mode.
To bypass plug-ins, display the parameters of the plug-in you wish to bypass in the INSERT
ASSIGN/EDIT section, then turn on the BYPASS button.
Scrub & Shuttle
By assigning the DAW SCRUB parameter to one of the User Defined buttons [1]–[8], you
can scrub Pro Tools tracks back and forth by turning the Parameter wheel. By assigning the
DAW SHUTTLE parameter to one of the User Defined buttons [1]–[8], you can shuttle
back and forth by turning the Parameter wheel.
1 Assign the DAW SCRUB or DAW SHUTTLE parameter to one of the User
Defined buttons [1]–[8].
Before assigning parameters to these buttons, you must switch layers to cancel the Remote
function. See page 235 for more information on assigning the parameters to the User
Defined buttons.
2 Press the LAYER [REMOTE] button to enable remote control of Pro Tools.
3 Make sure that Pro Tools is stopped.
4 Press the User Defined button to which you assigned the DAW SCRUB or
DAW SHUTTLE parameter in Step 1.
You can now use the Scrub or Shuttle function.
01V96 Version 2—Owner’s Manual
Pro Tools Remote Layer
205
5 Rotate the Parameter wheel.
Rotate the Parameter wheel clockwise to scrub or shuttle forwards. Turn it counterclockwise to scrub or shuttle backwards.
The minimum scrub playback step varies depending on the zoom setting in the Pro Tools
Edit window.
6 To cancel the Scrub or Shuttle function, press the User Defined button or
DAW SHUTTLE to which you assigned the DAW SCRUB parameter in Step 1.
Alternatively, you can cancel the Scrub or Shuttle function by pressing the User Defined
button to which the DAW STOP parameter is assigned. The Scrub function is automatically
cancelled if you commence playback or fast forward.
Note: The Scrub/Shuttle operation might be stopped unexpectedly by Pro Tools. Therefore,
whenever you use the Scrub or Shuttle function, make sure that the P.WHEEL MODE parameter indicates “SCRUB” or “SHUTTLE.” You can check the Scrub/Shuttle function status by
viewing the corresponding User Defined button indicator.
Automation
If you assign a parameter that controls Pro Tools Automation mode (such as DAW Auto
Read, DAW Auto Touch, etc.) to one of the User Defined buttons, you can control the Automation settings for each channel by using that User Defined button. See page 235 for more
information on assigning parameters to User Defined buttons.
Press the STEREO OUT channel [SEL] button. The button indicator lights up, and the
Channel 1–16 [SEL] buttons become available for the Automation mode setting.
Press the desired channel [SEL] buttons while pressing the programmed User Defined button to switch the corresponding channels’ Automation settings.
While the channel [SEL] buttons are available for the Automation mode setting, pressing
the [SEL] buttons will cause the Fader Touch or Untouch command to be transmitted to
Pro Tools. This is useful for Automation punch in and out recording.
Note: Operating a fader also causes the Fader Touch command to be transmitted. Also, whenever the transport mode changes (such as Play and Stop), the Fader Untouch command is
transmitted.
Depending on the currently-selected Automation mode, the channel [SEL] button indicators operate as follows:
User Defined Keys
Function
Pro Tools Automation
Mode
Auto write
DAW AUTO TOUTCH
Auto touch
DAW AUTO LATCH
Auto latch
DAW AUTO READ
Auto read
DAW AUTO OFF
Auto off
Flashing red (Record Ready)
Red (Recording)
Illuminated steadily
Off
01V96 Version 2—Owner’s Manual
17
Remote Control
DAW AUTO WRITE
[SEL] Button Indicators
206
Chapter 17—Remote Control
Nuendo/Cubase SX Remote Layer
You can remotely control Nuendo and Cubase SX using the Remote Layer.
■ Configuring Computers
1 Connect the 01V96 to your computer using a USB cable, and install the
required USB driver included on the 01V96 CD-ROM.
Refer to the Studio Manager installation guide for more information on installing the
driver.
2 Launch Nuendo/Cubase SX, select the Device Setup menu, and set up
Nuendo/Cubase SX so that the 01V96 can communicate with the software.
Refer to the Nuendo/Cubase SX User’s Manual for more information on setting up the software.
■ Configuring the 01V96
1 Refer to page 192 to configure the DIO/Setup | MIDI/HOST page.
2 Press the LAYER [REMOTE] button to set the TARGET parameter to
Nuendo/Cubase SX.
You can now remotely control Nuendo/Cubase SX using the Remote Layer.
Other DAW Remote Layer
You can remotely control DAW software that supports the Pro Tools protocol.
■ Configuring Computers
1 Connect the 01V96 to your computer using a USB cable, and install the
required USB driver included on the 01V96 CD-ROM.
Refer to the Studio Manager installation guide for more information on installing the
driver.
2 Launch and set up the DAW software so that the 01V96 communicates with
the software.
Refer to the DAW software’s user’s manual for more information on setting up the software.
■ Configuring the 01V96
1 Refer to page 192 to configure the DIO/Setup | MIDI/HOST page.
2 Press the LAYER [REMOTE] button to set the TARGET parameter to General
DAW.
You can now remotely control the DAW software using the Remote Layer.
01V96 Version 2—Owner’s Manual
MIDI Remote Layer
207
MIDI Remote Layer
If you select USER DEFINED as the target for the Remote Layer, you can remotely control
the parameters of external MIDI devices (such as synthesizers and tone generators) by operating the channel [ON] buttons, and faders to output various MIDI messages. (This is
called MIDI Remote function.)
You can store MIDI messages assigned to the channel controls in four banks. When the
01V96 is shipped from the factory, it includes MIDI settings in these banks, which you can
quickly recall to use the MIDI Remote function.
If necessary, you can also assign other MIDI messages to the faders or [ON] buttons to
remotely control the parameters of a connected MIDI device.
Using the MIDI Remote Function
This section describes how to recall and use the factory-preset MIDI Remote settings stored
in the banks.
By default, the 01V96’s four MIDI Remote banks (Banks 1–4) contain the following MIDI
messages.
Bank
Control Function
Usage
[ON] buttons
Faders
1
Panning and setting GM sound levels
—
Volume
2
Setting GM sound effect send levels
—
Effect Send
3
Setting XG sound levels
—
Volume
4
Adjusting mute, and levels for Cubase series mixer
Mute
Volume
1 Connect the 01V96’s MIDI OUT port to the MIDI IN port of the MIDI device.
MIDI OUT
MIDI IN
CH1-4
1
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
CH9-12
PHANTOM +48V
L
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
MUSIC PRODUCTION SYNTHESIZER
Integrated Sampling Sequencer
Real-time External Control Sur face
Modular Synthesis Plug-in System
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
SONG SCENE
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
CH15/16
2TR IN
INSERT I/O
REC
MONITOR
2TR IN
PAD
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
-16
-60
GAIN
GAIN
PEAK
SIGNAL
13
PEAK
14 15
SIGNAL
MIDI
UTILITY
PAIR/
GROUP
PATCH
EFFECT
VIEW
LEVEL
10
STORE
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
PEAK
16
SIGNAL
SCENE MEMORY
0
-3
PAN
-6
EQ
DYNAMICS
DEC
INC
-9
-12
FADER MODE
-15
Synthesizer
EQUALIZER
-18
-24
-30
AUX 1
AUX 2
AUX 3
AUX 4
AUX 7
AUX 8
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
HIGH-MID
FREQUENCY
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
5
10
10
5
10
10
0 +10
0 +10
10
10
10
10
0
0
5
5
0
10
10
10
15
15
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20
20
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
30
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
15
40
50
1
5
15
5
15
20 10
2
5
15
20 10
3
4
10
5
15
5
10
5
15
6
10
5
15
7
15
5
15
5
15
9
5
15
10
5
15
20 10
20 10
20 10
20 10
8
10
10
10
5
11
12
5
15
13
5
15
14
SEL
SOLO
ON
ON
ST IN 1
10
5
SEL
SOLO
ON
ST IN 2
5
5
0
0
0
0 +10
5
5
5
5
0
0 +10
5
5
5
5
0
0
0
0 +10
5
5
5
5
0
0 +10
5
5
5
0
0 +10
0 +10
5
5
0
0
0 +10
5
5
5
0
0 +10
0 +10
5
5
0
0
0 +10
5
5
5
5
0
0 +10
0 +10
0 +10
+10
SEL
5
15
15
5
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
17
Remote Control
01V96 Version 2—Owner’s Manual
208
Chapter 17—Remote Control
2 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | MIDI/Host page appears.
1
3 Move the cursor to the REMOTE parameter box (1) in the SPECIAL FUNCTIONS section, rotate the Parameter wheel to select MIDI, then press
[ENTER].
If the MIDI port is already in use, a window confirming the assignment change appears.
Move the cursor to the YES button, then press [ENTER].
Tip: If the REMOTE parameter box is grayed out, proceed to Steps 4 and 5 to set the TARGET
parameter, then return to Steps 2 and 3.
4 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Remote page appears.
5 Move the cursor to the TARGET parameter box, rotate the Parameter wheel
to select USER DEFINED, then press [ENTER].
The confirmation window for changing the setting appears. Move the cursor to the YES
button, then press [ENTER]. The display changes as follows:
1
4
3
2
5
6
A TRANSMIT ENABLE/DISABLE
This button switches the MIDI Remote function between enable and disable.
B INITIALIZE
This button resets the settings stored in the bank selected by the BANK parameter their
default settings.
C BANK
This parameter enables you to select one of four banks.
01V96 Version 2—Owner’s Manual
MIDI Remote Layer
209
D ID, SHORT, LONG
These parameters display the channel names. The ID parameter displays the channel ID
(RM01–RM16) for the currently-controlled MIDI device.
E ON section
This section displays the type of MIDI messages (in hexadecimal or alphabet) assigned
to the [ON] buttons for the currently-selected channels (RM01–RM16).
• LATCH/UNLATCH......This button toggles between Latch and Unlatch for [ON] button operation.
• LEARN...........................When you turn on this button, MIDI messages received at the
MIDI IN port are assigned to the DATA parameter boxes.
• DATA parameter boxes ...................... These boxes display the type of MIDI messages
(in hexadecimal or alphabets) assigned to the
[ON] button).
F FADER section
This section displays the type of MIDI messages (in hexadecimal or alphabet) assigned
to the faders for the currently-selected channels (RM01–RM16).
6 Move the cursor to the desired bank button (BANK parameter buttons 1–4),
then press [ENTER].
7 Press the LAYER [REMOTE] button to select Remote layer.
You can now use the MIDI Remote function.
8 Use the faders and [ON] buttons to control the MIDI device.
Assigning MIDI Messages to Channel Controls
You can quickly use the MIDI Remote function if you use the factory presets in the banks.
However, you can also assign the desired MIDI messages to the faders or [ON] buttons.
This section describes how to assign MIDI messages to the channel controls, using the
example of assigning Hold On/Off messages (Control Change #64; Values 127 & 0) to the
Channel 1 [ON] button.
1 Connect the 01V96’s MIDI IN port to the MIDI OUT port of a MIDI keyboard
to which a Hold On/Off controllable foot switch is connected. Enable the
MIDI Remote function on the 01V96.
MIDI OUT
MIDI IN
CH1-4
1
2
3
4
5
6
7
8
9
10
11
MIDI OUT
CH5-8
12
13
15
MIDI IN
CH9-12
PHANTOM +48V
17
L
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
14
16
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
CH15/16
2TR IN
INSERT I/O
MONITOR
2TR IN
PAD
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
13
PEAK
14 15
SIGNAL
LEVEL
PEAK
16
SIGNAL
MIDI
UTILITY
PAIR/
GROUP
PATCH
EFFECT
VIEW
STORE
RECALL
10
MIDI keyboard
SCENE MEMORY
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
0
-3
PAN
-6
EQ
DYNAMICS
DEC
INC
-9
-12
FADER MODE
-15
EQUALIZER
-18
-24
-30
AUX 1
AUX 2
AUX 3
AUX 4
AUX 7
AUX 8
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
HIGH-MID
FREQUENCY
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
+10
0 +10
5
0 +10
5
5
0
10
0 +10
5
0
0 +10
5
5
5
0
5
0
10
0
0
5
5
0
10
10
10
15
15
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20
20
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
30
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
15
40
50
1
5
15
5
15
20 10
2
5
15
20 10
3
4
5
15
5
5
15
6
10
5
15
7
10
5
15
10
5
15
20 10
8
10
5
15
20 10
9
5
15
10
5
15
20 10
20 10
11
12
5
15
13
5
15
14
SEL
SOLO
ON
ON
ST IN 1
ST IN 2
5
5
0
10
0 +10
5
5
0
10
0 +10
5
5
0
SEL
SOLO
ON
10
5
10
5
0
0 +10
5
5
5
0
0 +10
0 +10
5
5
0
10
0 +10
5
5
0
10
0 +10
5
5
0
10
0 +10
5
5
0
10
0 +10
5
5
5
0
0 +10
0 +10
5
5
0
SEL
10
5
15
15
5
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
Foot switch
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
01V96 Version 2—Owner’s Manual
Remote Control
DIO/SETUP
-60
GAIN
DISPLAY ACCESS
SCENE
-16
210
Chapter 17—Remote Control
2 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | Remote page appears, then set the TARGET parameter to USER
DEFINED.
You can now use the MIDI Remote function. Refer to the previous section for more information on using the MIDI Remote function.
3 Move the cursor to the desired bank button (BANK parameter buttons 1–4),
then press [ENTER].
4 Press the [SEL] buttons for the desired channels.
Currently-assigned MIDI messages appear in the ON and FADER sections.
Tip: You can also choose the desired channels using the ID, SHORT, and LONG parameters.
5 Move the cursor to the LEARN button in the ON section, then press [ENTER].
MIDI messages received at the MIDI IN port of the 01V96 will be assigned to the DATA
parameter boxes in the ON section.
6 Press and hold down the MIDI keyboard foot switch.
The MIDI Hold On message is assigned in the DATA parameter box.
MIDI messages are described below:
• 00–7F ............................. MIDI messages are expressed in hexadecimal.
• END ............................... This message indicates the end of MIDI messages. Subsequent
messages assigned in the DATA parameter boxes will be
ignored.
• –...................................... This message indicates that no messages are assigned to the
DATA parameter boxes.
Tip: When you click the LEARN button to assign MIDI messages, the 01V96 automatically
recognizes the end of the messages and assigns END and “–.”
7 While continuing to hold down the foot switch, turn off the LEARN button.
8 Move the cursor to the third parameter box (“7F” in this example), then
rotate the Parameter wheel to change the value to SW.
“SW” is a variable that changes depending on the [ON] button’s on/off status. You can use
the following variables in MIDI messages.
• SW.................................. This variable is selectable only in the DATA parameter boxes of
the ON section. When the [ON] buttons are turned on, “7F”
(127 in decimal) is output. When the [ON] buttons are turned
off, “00” (0 in decimal) is output.
• FAD................................ This variable is selectable only in the DATA parameter boxes of
the FADER section. When you operate the faders, continuously
01V96 Version 2—Owner’s Manual
MIDI Remote Layer
211
changing values in the range of 00 to 7F (0–127 in decimal) are
output.
Tip: If “SW” is not assigned in the DATA parameter boxes of the ON section, the current MIDI
messages are output.
Note: Be sure to set one of the DATA parameter boxes of the FADER section to “FAD.” If no
“FAD” is assigned, fader operation is ignored.
9 Move the cursor to the LATCH/UNLATCH button, then press [ENTER] to
select LATCH or UNLATCH depending on how you want the [ON] buttons
to function.
• LATCH...........................Pressing the [ON] buttons repeatedly transmits alternating On
and Off messages.
• UNLATCH ....................Pressing and holding down the [ON] buttons transmits On
messages, and releasing the [ON] buttons transmits Off messages.
Tip: Refer to the diagrams below for information on how the [ON] buttons behave when Latch
or Unlatch is selected.
■ When “SW” is assigned:
- LATCH
MIDI data transmission
(SW=7F)
Off
MIDI data transmission
(SW=00)
Illuminated
Off
- UNLATCH
MIDI data transmission
(SW=7F)
Off
Illuminated
MIDI data transmission
(SW=00)
Off
17
■ When “SW” is not assigned:
Remote Control
- UNLATCH
MIDI data transmission
Off
Illuminated
Off
Tip: In most situations, select Unlatch if SW is not assigned.
01V96 Version 2—Owner’s Manual
212
Chapter 17—Remote Control
10 To change the channel name, move the cursor to the ID LONG parameter
box, then press [ENTER] to display the Title Edit window.
Refer to page 30 for more information on editing names.
Tip:
• Move the cursor to the INITIALIZE button, then press [ENTER]. A window is displayed
that enables you to reset the parameter settings in the currently-selected bank.
• You can also assign MIDI messages to the parameter boxes manually without using the
LEARN button.
Machine Control Function
The 01V96 can control the transport functions and select tracks on external recording
machines that support MMC by transmitting commands via the MIDI OUT port or USB
port.
Note: Controllable parameters vary depending on the connected devices. Refer to the User’s
Manual for the external device for more information on controllable parameters.
1 Refer to the diagram below for information on connecting the 01V96 to an
external device.
MIDI OUT
MIDI IN
MIDI OUT
CH1-4
1
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
MIDI IN
CH9-12
PHANTOM +48V
L
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
14
16
R
IN
INPUT
OUT
2TR
(BAL)
-10dBV (UNBAL)
PHONES
INSERT
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
CH15/16
2TR IN
INSERT I/O
MONITOR
2TR IN
PAD
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-16
-60
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DIO/SETUP
-60
GAIN
DISPLAY ACCESS
SCENE
-16
PEAK
SIGNAL
13
PEAK
14 15
SIGNAL
LEVEL
PEAK
16
SIGNAL
10
MMC-supported
machine
SCENE MEMORY
MIDI
UTILITY
PAIR/
GROUP
PATCH
EFFECT
VIEW
STORE
RECALL
SOLO
CLEAR
SELECTED CHANNEL
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
PHONES
0
-3
PAN
-6
EQ
DYNAMICS
DEC
INC
-9
-12
FADER MODE
-15
EQUALIZER
-18
-24
-30
AUX 1
AUX 2
AUX 3
AUX 4
AUX 7
AUX 8
-36
HIGH
Q
-48
STEREO
AUX 5
AUX 6
HIGH-MID
FREQUENCY
HOME (METER)
LOW-MID
LAYER
ENTER
1-16
17-32
LOW
GAIN
MASTER REMOTE
ST IN
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
5
10
10
5
10
10
0 +10
5
5
0
0 +10
5
5
0
5
0
0 +10
5
5
5
0
0 +10
0 +10
5
5
0
0
0
5
5
0
0
10
10
15
15
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20
20
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
30
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
15
40
50
1
5
15
5
15
20 10
2
5
15
20 10
3
5
15
20 10
4
5
5
15
6
5
15
7
10
5
15
10
5
15
20 10
8
10
5
15
20 10
9
10
5
15
20 10
10
11
10
10
5
15
20 10
5
15
20 10
12
13
10
10
5
15
14
SEL
SOLO
ON
ON
ST IN 1
ST IN 2
5
5
5
0
SEL
SOLO
ON
10
5
10
0 +10
5
5
0
10
0 +10
5
5
0
10
0 +10
5
5
0
0
0 +10
5
5
5
0
0 +10
0 +10
5
5
0
0
0 +10
5
5
5
5
0
0 +10
0 +10
0 +10
+10
SEL
5
15
15
5
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
STEREO
2 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | MIDI/Host page appears.
1
01V96 Version 2—Owner’s Manual
Machine Control Function
213
3 Move the cursor to the PORT parameter box in the MACHINE CONTROL section (1), then rotate the Parameter wheel to select the MMC destination.
The following ports and slot are available as the MMC destination.
• MIDI ..............................MIDI port
• USB ................................USB port
• SLOT ..............................Slot with an MY8-mLAN (mLAN card) installed
If USB is selected, move the cursor to the adjacent parameter box (on the right), and select
one of eight ports.
4 Move the cursor to the DEVICE ID parameter box, then rotate the Parameter
wheel to set the 01V96 MMC Device ID to the same ID number as the external device.
MMC commands are effective on devices that use the same Device ID. Therefore, the
01V96’s MMC Device ID needs to match the ID of the devices you wish to control.
5 To start remote control, press the DISPLAY ACCESS [DIO/SETUP] button
repeatedly until the DIO/Setup | Machine page appears.
2
3
1
4
This page contains the following parameters:
A LOCATE/TIME section
•
•
•
•
B TRACK ARMING section
This section controls the tracks on external machines.
• 1–24 buttons.................These buttons turn external tracks 1–24 on or off, and set or
cancel their Record Ready mode.
• ALL CLEAR...................Turning on this button switches all buttons (1–24) simultaneously.
01V96 Version 2—Owner’s Manual
17
Remote Control
This section enables you to set the locate points.
LOCATE 1–8 .................These buttons locate the positions (specified by the TIME values) on external machines.
RTZ ................................This Return To Zero button locates the zero timecode position
on external machines.
TIME..............................Locate points are specified in hour/minute/second/frame format.
CAPTURE .....................These buttons capture the current position on external
machines and import the information into the TIME column.
214
Chapter 17—Remote Control
C TRANSPORT section
•
•
•
•
•
This section enables you to control the transport functions on external machines.
REW............................... This button starts rewind on external machines.
FF ................................... This button starts fast forward on external machines.
STOP.............................. This button stops external machines.
PLAY .............................. This button starts playback on external machines.
REC................................ This button is used in conjunction with the PLAY button to
start recording on external machines.
D FRAMES
This parameter selects the timecode frame rate from 24, 25, 30D (drop frame), and 30.
6 To control the transport functions, move the cursor to the desired button in
the TRANSPORT section, then press [ENTER].
7 If you desire, move the cursor to the buttons and parameters in the
LOCATE/TIME section and the TRACK ARMING section, then press the
[ENTER] button or rotate the Parameter wheel to control the transport functions on external machines.
Tip: You can also use the programmed User Defined buttons to control Machine Control functions. (See page 235 for information on assigning functions to the User Defined buttons.)
01V96 Version 2—Owner’s Manual
MIDI
215
18 MIDI
This chapter describes the 01V96’s MIDI-related functions.
MIDI & the 01V96
Using Control Changes, Program Changes, and other MIDI messages enables you to recall
Scenes and edit parameters on the 01V96, and store 01V96 internal data on external MIDI
devices.
The 01V96 supports the following MIDI messages. Each of these MIDI messages can be
individually turned on or off for transmission and reception.
• Program Changes
If you assign the 01V96’s Scenes to Program Change numbers, the 01V96 transmits Program Changes when it recalls Scenes. Also, the 01V96 will switch Scenes when it receives
Program Changes.
• Control Changes
If you assign the 01V96’s parameters to Control Change numbers, the 01V96 transmits the
assigned Control Changes when the parameter values change. Also, the 01V96 changes certain parameter values when it receives the corresponding Control Changes.
• System Exclusive Messages
The 01V96 transmits System Exclusive Parameter Changes in real-time when the parameter
values change. Also, the 01V96 notifies certain parameter values when it receives assigned
Parameter Changes.
• MMC (MIDI Machine Control)
MMC is used for external machine control.
• MIDI Note On/Off
These messages are used to adjust the Freeze effect.
• Bulk Dump Messages
These messages enable you to store the 01V96’s internal data to a sequencer or MIDI filer.
When the 01V96 receives these messages, they overwrite the 01V96 data
The 01V96 features the following interface for transmitting and receiving MIDI data.
• MIDI IN/THRU/OUT ports
These ports transmit and receive MIDI data to and from standard MIDI devices. Each port
is a single port interface that transmits and receives single-port data (16 channels x 1 ports).
The MIDI THRU port outputs MIDI messages received at the MIDI IN port without modification (as is).
Note: If the computer is turned on but the USB MIDI application has not been launched,
01V96 performance may be slow. In this case, cancel the assignment of the USB port as the
MIDI message transmission port.
01V96 Version 2—Owner’s Manual
18
MIDI
• USB port
This port is used to connect a computer and transfer MIDI messages. This is a multiport
interface that transmits and receives up to eight-port data (16 channels x 8 ports). If you
connect a computer to the USB port, you must install the appropriate driver software on
the computer. See the Studio Manager Installation Guide for more information on installing drivers.
216
Chapter 18—MIDI
• SLOT
If an optional “MY8-mLAN” I/O card is installed in the slot, MIDI data transfer to and from
an external MIDI device is available via the MY8-mLAN card.
MIDI Port Setup
Selecting a Port for MIDI Message Transfer
To configure MIDI ports for MIDI message transfer, press the DISPLAY ACCESS
[DIO/SETUP] button repeatedly until the DIO/Setup | MIDI/Host page appears. This page
enables you to set MIDI message input and output.
1
4
2
3
The following parameters are available on this page:
A GENERAL section
This section enables you to select ports that transmit and receive MIDI messages, such
as Program Changes and Control Changes.
• Rx PORT ....................... This parameter specifies a port for general MIDI data reception. In the left parameter box, select MIDI, USB, or SLOT. If
you select USB or SLOT, specify the port number (1–8) in the
right parameter box.
• Tx PORT ....................... This parameter specifies a port for general MIDI data transmission. The available ports are the same as for the Rx PORT
parameter.
B MIDI THRU section
These parameters enable you to route incoming MIDI data from one port or slot to
another without changes. Select a port for reception in the first parameter box, and
select a port for transmission in the next parameter box (located to the right of the
arrow). If you select USB or SLOT, specify the port number in the small parameter box
adjacent to the port parameter box.
C MACHINE CONTROL section
This section enables you to select a remote control method and a remote control port to
control external devices that support MMC, such as a hard disk recorder.
• PORT ............................. Select MIDI, USB, or SLOT for MMC command transfer. If
you select USB or SLOT, specify the port number in the right
parameter box.
01V96 Version 2—Owner’s Manual
MIDI Port Setup
217
• DEVICE ID ...................Specify the 01V96’s MMC Device ID. MMC Device IDs identify connected devices, enabling recognition during MMC
transmission and reception.
D SPECIAL FUNCTIONS section
•
•
•
•
This section enables you to specify ports for various special functions.
Studio Manager............In the left parameter box, select MIDI, USB or SLOT as the port
used by the included Studio Manager software. In the two small
parameter boxes on the right, specify a port number (if you
selected USB), and an ID number.
DAW...............................Select USB or SLOT as a port for use with a DAW. Specify in the
right parameter box a port number pair (1–2, 3–4, 5–6, 7–8).
REMOTE ......................This parameter indicates the target currently selected for
Remote Layer. If the target is set to “USER DEFINED,” you can
select a MIDI message destination port.
CASCADE LINK ..........This parameter determines whether MIDI messages are transmitted between two cascaded 01V96s. If you select MIDI, MIDI
messages will be transferred between two cascaded units. If you
select “–,” no MIDI messages are transferred.
The TRANSMIT and REQUEST buttons are used to synchronize all parameters that are cascade-linked. The TRANSMIT
button synchronizes the connected 01V96’s parameters to your
primary 01V96’s parameters. The REQUEST button synchronizes your 01V96 parameters to the connected 01V96’s parameters.
18
MIDI
01V96 Version 2—Owner’s Manual
218
Chapter 18—MIDI
Selecting MIDI Messages for Transmission and Reception
You can select MIDI messages to be transmitted or received at a specified port.
To do so, press the DISPLAY ACCESS [MIDI] button, then press the [F1] button to display
the MIDI | Setup page.
1
2
3
4
5
6
7
Select MIDI channels for transmission and reception in the CHANNEL row, and turn the
transmission and reception of each MIDI message on or off using the buttons in the parameter rows from PROGRAM CHANGE to OTHER COMMANDS.
A CHANNEL
This parameter row enables you to specify MIDI Channels for MIDI message transmission and reception. The following parameters are available in this row:
• Tx ................................... This parameter box specifies a MIDI Transmit Channel.
• Rx ................................... This parameter box specifies a MIDI Receive Channel.
B PROGRAM CHANGE
•
•
•
•
This parameter row enables or disables transmission and reception of Program
Changes.
Tx ON/OFF................... Transmission of Program Change messages is enabled or disabled.
Rx ON/OFF................... Reception of Program Change messages is enabled or disabled.
OMNI ON/OFF............ When this button is turned on, Program Changes on all MIDI
Channels are received regardless of the CHANNEL row settings.
ECHO ON/OFF ........... This button determines whether Program Change messages
received at the MIDI IN port are echoed through to the MIDI
OUT port.
C CONTROL CHANGE
This parameter row enables or disables transmission and reception of Control Changes.
• Tx ON/OFF................... Transmission of Control Change messages is enabled or disabled.
• Rx ON/OFF................... Reception of Control Change messages is enabled or disabled.
• ECHO ON/OFF ........... This button determines whether Control Change messages
received at the MIDI IN port are echoed through to the MIDI
OUT port.
D PARAMETER CHANGE
This parameter row enables or disables transmission and reception of Parameter
Changes.
01V96 Version 2—Owner’s Manual
Assigning Scenes to Program Changes for Remote Recall
219
• Tx ON/OFF...................Transmission of Parameter Change messages is enabled or disabled.
• Rx ON/OFF................... Reception of Parameter Change messages is enabled or disabled.
• ECHO ON/OFF............This button determines whether Parameter Change messages
received at the MIDI IN port are echoed through to the MIDI
OUT port.
E BULK
This parameter row enables or disables reception of Bulk Dump data.
• Rx ON/OFF...................Reception of Bulk Dump data is enabled or disabled.
F OTHER COMMANDS
• ECHO ON/OFF............This button determines whether other MIDI messages received
at the MIDI IN port are echoed through to the MIDI OUT
port.
G Fader Resolution
This parameter specifies the resolution of the value output when you operate the
01V96’s faders. To transfer fader value data between two cascaded 01V96s, or to record
the 01V96 operation to or play it back from a sequencer, select the HIGH button. When
the LOW button is selected, the fader resolution switches to 256 steps.
Assigning Scenes to Program Changes for Remote Recall
You can assign 01V96 Scenes to MIDI Program Changes for remote recall. When you recall
a Scene on the 01V96, the unit transmits the assigned Program Change to the connected
MIDI device. When the 01V96 receives a Program Change, the assigned Scene is recalled.
Initially, Scenes 1 through 99 are assigned sequentially to Program Changes 1 through 99,
and Scene #0 is assigned to Program Change #100, although you can change these assignments.
Tip: You can store a Scene to Program Change assignment table to an external device by using
MIDI Bulk Dump or the included Studio Manager software.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | MIDI/Host page appears, then specify ports for transmission
and reception of MIDI messages (see page 216).
2 Make connections using the ports selected in Step 1 so that the 01V96 can
transfer MIDI messages to and from the external device.
3 Press the DISPLAY ACCESS [MIDI] button, then press the [F2] button.
The MIDI | Pgm Asgn page appears.
18
MIDI
01V96 Version 2—Owner’s Manual
220
Chapter 18—MIDI
4 Move the cursor to a parameter box in the PGM CHG column, and rotate
the Parameter wheel or press the [INC]/[DEC] buttons to select the Program
Change numbers to which you want to assign Scenes.
5 Press the cursor button [ ] to move the cursor to a parameter box in the
SCENE NO./TITLE column, then rotate the Parameter wheel or press the
[INC]/[DEC] buttons to select Scenes.
Tip:
• If you assign a Scene to multiple Program Changes, the Program Change with the lowest
number becomes effective.
• You can initialize the Scene to Program Change assignment table by moving the cursor to
the INITIALIZE button, then pressing [ENTER].
6 Press the DISPLAY ACCESS [MIDI] button, then press the [F1] button to display the MIDI | Setup page, then specify the MIDI Transmit and Receive
Channels.
7 Turn on the PROGRAM CHANGE Tx ON/OFF and Rx ON/OFF buttons.
Now, when the 01V96 receives the Program Changes on the specified MIDI Channels, the
corresponding Scenes are recalled. Also, when you switch Scenes on the 01V96, the 01V96
transmits the Program Changes on the specified MIDI Channels.
Assigning Parameters to Control Changes for Real-time
Control
You can assign 01V96 parameters to MIDI Control Changes for real-time control. When
the 01V96 receives a Control Change, the assigned 01V96 parameter is set accordingly. Also,
when you adjust a parameter on the 01V96, the 01V96 transmits the assigned Control
Change message.
Tip: You can store a Parameter to Control Change assignment table to an external device by
using MIDI Bulk Dump or the included Studio Manager software.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | MIDI/Host page appears, then specify ports for transmission
and reception of MIDI messages (see page 216).
2 Make connections using the ports selected in Step 1 so that the 01V96 can
transfer MIDI messages to and from the external device.
3 Press the DISPLAY ACCESS [MIDI] button, then press the [F3] button.
The MIDI | Ctl Asgn page appears. This page enables you to assign 01V96 parameters to
Control Changes.
1
01V96 Version 2—Owner’s Manual
Assigning Parameters to Control Changes for Real-time Control
221
Tip: See page 290 for information on the default Parameter to Control Change assignments.
4 Move the cursor to the MODE parameter’s TABLE button (1), then press
[ENTER].
The MODE parameter determines which MIDI messages are transmitted when 01V96
parameters are adjusted. The following options are available for the MODE parameter:
• TABLE............................MIDI Control Change messages are transmitted in accordance
with the assignments on this page.
• NRPN.............................The assignments on the Ctl Asgn page are ignored, and predefined NRPNs (Non Registered Parameter Numbers) are
transmitted for remote control.
Tip: NRPNs are special MIDI messages that combine three different Control Changes. They
enable you to control many parameters on a single MIDI Channel.
5 If you turned on the TABLE button in Step 4, move the cursor to a parameter
box in the No. (CH) column, then rotate the Parameter wheel or press the
[INC]/[DEC] buttons to select the MIDI channels and Control Changes to
which you want to assign parameters.
You can assign parameters to up to 16-channel Control Changes on the Ctl Asgn page,
regardless of the MIDI Channels currently selected for transmission and reception.
Skip Steps 5 and 6 if you turned on the NRPN button in Step 4.
6 Select parameters in the parameter boxes in the three PARAMETER columns.
Select a parameter group in the parameter box in the first PARAMETER column, and specify the desired values in the parameter boxes in the second and third PARAMETER columns.
The following parameters and values are available:
HIGH
MID
NO ASSIGN
LOW
—
—
CHANNEL
INPUT1–32/ST IN1–4
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
AUX2 SEND
AUX3 SEND
FADER H
AUX4 SEND
AUX5 SEND
INPUT1–32/ST IN1–4
AUX6 SEND
AUX7 SEND
AUX8 SEND
BUS TO ST
BUS1–8
CHANNEL
INPUT1–32/ST IN1–4
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
AUX2 SEND
MIDI
AUX3 SEND
FADER L
AUX4 SEND
AUX5 SEND
INPUT1–32/ST IN1–4
AUX6 SEND
AUX7 SEND
AUX8 SEND
BUS TO ST
18
BUS1–8
01V96 Version 2—Owner’s Manual
222
Chapter 18—MIDI
HIGH
MID
LOW
CHANNEL
INPUT1–32/ST IN1–4
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
AUX2 SEND
AUX3 SEND
ON
AUX4 SEND
AUX5 SEND
INPUT1–32/ST IN1–4
AUX6 SEND
AUX7 SEND
AUX8 SEND
PHASE
INSERT ON
BUS TO ST
BUS1–8
CHANNEL
INPUT1–32/ST IN1L–4R
CHANNEL
INPUT1–32
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
AUX2 SEND
AUX3 SEND
PRE/POST
AUX4 SEND
AUX5 SEND
INPUT1–32/ST IN1–4
AUX6 SEND
AUX7 SEND
AUX8 SEND
ON
TIME HIGH
TIME MID
IN DELAY
TIME LOW
MIX HIGH
INPUT1–32
MIX LOW
FB GAIN H
FB GAIN L
ON
OUT DELAY
TIME HIGH
TIME MID
TIME LOW
01V96 Version 2—Owner’s Manual
BUS1–8/AUX1–8/STEREO L,R
Assigning Parameters to Control Changes for Real-time Control
HIGH
MID
223
LOW
ON
Q LOW
F LOW
G LOW H
G LOW L
Q LO-MID
F LO-MID
G LO-MID H
G LO-MID L
Q HI-MID
EQ
F HI-MID
INPUT1–32/ST IN 1–4/BUS1–8/AUX1–8/STEREO
G HI-MID H
G HI-MID L
Q HIGH
F HIGH
G HIGH H
G HIGH L
ATT H
ATT L
HPF ON
LPF ON
ON
ATTACK
THRESH H
THRESH L
GATE
RANGE
INPUT1–32
HOLD H
HOLD L
DECAY H
DECAY L
ON
ATTACK
THRESH H
THRESH L
COMP
RELEASE H
RELEASE L
INPUT1–32/BUS1–8/AUX1–8/STEREO
RATIO
GAIN H
GAIN L
KNEE
CHANNEL
AUX1–2
PAN
AUX3–4
INPUT1–32/ST IN1L–4R
AUX5–6
BALANCE
BUS TO ST
BUS1–8
MASTER
STEREO
MIDI
AUX7–8
18
01V96 Version 2—Owner’s Manual
224
Chapter 18—MIDI
HIGH
MID
LOW
LFE H
LFE L
DIV (F)
DIV R
SURROUND
LR
FR
INPUT1–32/ST IN1L–4R
WIDTH
DEPTH
OFS LR
OFS FR
BYPASS
MIX
PARAM1 H
EFFECT
PARAM1 L
EFFECT1–4
:
PARAM32 H
PARAM32 L
Parameters that feature a setting range of more than 128 steps (such as Fader and Delay
Time parameters) require two or more Control Change messages to specify the values.
For example, if you wish to control Fader parameters on certain channels using Control
Changes, you must assign the same channel to two Control Change numbers, and select
“FADER H” and “FADER L” for the Control Changes in the parameter boxes in the first
PARAMETER column.
If you wish to control Delay Time parameters on certain channels using Control Changes,
you must assign the same channel Delay parameter to three Control Change numbers, and
select “TIME LOW,” “TIME MID,” and “TIME HIGH” for the Control Changes in the
parameter boxes in the second (middle) PARAMETER column.
Note: Parameters that feature a setting range in excess of 128 steps require an appropriate
combination of range parameters for successful MIDI Control Change.
Tip: You can initialize the Parameter to Control Change assignment table by moving the cursor to the INITIALIZE button, then pressing [ENTER].
7 Press the DISPLAY ACCESS [MIDI] button, then press the [F1] button to display the MIDI | Setup page, then specify MIDI Transmit and Receive Channels.
8 Turn on the CONTROL CHANGE Tx ON/OFF and Rx ON/OFF buttons.
01V96 parameters will now be set accordingly when the 01V96 receives corresponding
Control Changes. Also, when you adjust parameters on the 01V96, the 01V96 will transmit
corresponding Control Changes.
Note: Before controlling parameters using Control Changes, make sure that both Tx and Rx
ON/OFF buttons in the PARAMETER CHANGE row on the MIDI | Setup page are turned off.
01V96 Version 2—Owner’s Manual
Controlling Parameters by Using Parameter Changes
225
Controlling Parameters by Using Parameter Changes
You can control 01V96 parameters in real time by using Parameter Change messages that
are System Exclusive messages, instead of using MIDI Control Changes.
See “MIDI Data Format” at the end of this Manual for detailed information on available
Parameter Changes.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | MIDI/Host page appears, then specify ports for transmission
and reception of MIDI messages (see page 216).
2 Make connections using the ports selected in Step 1 so that the 01V96 can
transmit and receive MIDI messages to and from the external device.
3 Press the DISPLAY ACCESS [MIDI] button, then press the [F1] button to display the MIDI | Setup page, then turn off the Tx and Rx ON/OFF buttons in
the PARAMETER CHANGE row.
The 01V96 will now set certain parameter values when it receives corresponding Parameter
Changes. Also, when you adjust certain parameters on the 01V96, it transmits corresponding Parameter Changes.
Note: Before controlling parameters using Parameter Changes, make sure that both Tx and
Rx ON/OFF buttons in the CONTROL CHANGE row are turned off.
18
MIDI
01V96 Version 2—Owner’s Manual
226
Chapter 18—MIDI
Transmitting Parameter Settings via MIDI (Bulk Dump)
You can back up data stored in the 01V96, such as libraries and Scenes, to an external MIDI
device by using MIDI Bulk Dump. In this way, you can later restore previous 01V96 settings
by transmitting this MIDI data back to the 01V96.
Note: Some of the data transmitted from the 01V96 to the sequence software may occasionally
drop out during Bulk Dump transmission. To avoid this, we recommend that you use the
included Studio Manager software to store 01V96 data to an external device.
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup | MIDI/Host page appears, then specify ports for transmission
and reception of MIDI messages (see page 216).
2 Make connections using the ports selected in Step 1 so that the 01V96 can
transmit and receive MIDI messages to and from the external device.
3 Press the DISPLAY ACCESS [MIDI] button, then press the [F4] button.
The MIDI | Bulk page appears.
1
2
3
4
The page includes the following parameters:
A CATEGORY section
This section enables you to select data for transmission and reception.
B REQUEST
Move the cursor to this button, then press [ENTER] to transmit messages from the
01V96 that request a second 01V96 (connected to the first 01V96) to transmit the data
specified in the CATEGORY section. This button is used primarily when two 01V96s are
connected in cascade.
C TRANSMIT
Move the cursor to this button, then press [ENTER] to transmit data specified in the
CATEGORY section to an external MIDI device.
D INTERVAL
This parameter specifies the interval between data packets during bulk transmission in
50 millisecond steps. If the external device drops part of the bulk data, increase this
parameter value.
4 In the CATEGORY section, move the cursor to the button of the data type
you want to transmit, then press [ENTER].
01V96 Version 2—Owner’s Manual
Transmitting Parameter Settings via MIDI (Bulk Dump)
227
The following options are available:
• ALL.................................This button selects all data available for bulk dump. When this
button is turned on, all other buttons in this section are turned
off.
• SCENEMEM .................This button selects Scene memories. You can select Scenes you
wish to transmit in the parameter box next to the button.
• LIBRARY.......................This button selects libraries. You can select the type of library in
the TYPE parameter box (next to the button), then specify the
library number in the parameter box on the right.
• BANK.............................This parameter enables you to select the User Defined Key
banks (KEYS UDEF), User Defined Remote Layer banks (RMT
UDEF), or User Assignable Layer banks (USR LAYER) for bulk
dump. You can select one of these three types in the parameter
box next to the button, and select the banks in the parameter
box on the right.
• SETUPMEM .................This button selects the 01V96 setup data (i.e., system settings).
• PGM TABLE .................This button selects the MIDI | Pgm Asgn page settings.
• CTL TABLE...................This button selects the MIDI | Ctl Asgn page settings.
• PLUG-IN .......................This button selects the settings of an optional Y56K card
installed in the slot. You can select Y56K card programs in the
parameter box next to the button..
Note: Data selected by the SETUPMEM button includes MIDI transmission and reception
port settings and message settings. After you store to an external device bulk dump data that
has its reception disabled, if the 01V96 later starts to receive this particular data, 01V96 bulk
dump reception will be turned off immediately, and the 01V96 will be unable to receive subsequent data. Therefore, before you store the data selected by the SETUPMEM button using
Bulk Dump, be sure to enable bulk data transmission and reception.
5 If necessary, move the cursor to the parameter box next to the selected button, then rotate the Parameter wheel or press the [INC]/[DEC] buttons to
select the desired bulk dump data.
Tip: If you selected [ALL] in the parameter box, all data selected by the corresponding button
is transmitted as bulk dump data.
6 To start transmitting bulk data, move the cursor to the TRANSMIT button,
then press [ENTER].
Bulk Dump is executed. During the operation, the Bulk Dump window appears, indicating
the current bulk dump status. To abort the bulk dump operation, move the cursor to the
CANCEL button in the window, then press [ENTER].
7 To receive bulk data, press the DISPLAY ACCESS [MIDI] button again to display the MIDI | Setup page, then turn on the Rx ON/OFF button in the BULK
row.
Now, when the 01V96 receives bulk data, the corresponding internal data is updated.
01V96 Version 2—Owner’s Manual
18
MIDI
Tip: To transmit bulk dump request messages, move the cursor to the REQUEST button, then
press [ENTER]. If you set up the 01V96 so that it will transmit and receive MIDI messages to
and from another 01V96, the other 01V96 will respond to the bulk dump request and transmit
the bulk dump data to the 01V96 you are operating.
228
Chapter 18—MIDI
01V96 Version 2—Owner’s Manual
Other Functions
229
19 Other Functions
This chapter describes the 01V96’s miscellaneous functions.
Changing the Input and Output Channel Names
You can change the default name of the input channels (Input Channels 1–32, ST IN Channels 1–4) and output channels (Aux Outs 1–8, Bus Outs 1–8, Stereo Out), if you desire.
Changing the Input Channel Names
1 Press the DISPLAY ACCESS [PATCH] button repeatedly until the Patch| In
Name page appears.
3
1
2
Channel IDs, Short names, and Long names are listed from left to right on the page. You
can specify Short names in the parameter boxes (1) in the center column, and Long names
in the parameter boxes (2) in the right column.
2 Move the cursor to the desired parameter box, then use the Parameter wheel
or the [INC]/[DEC] buttons to select a port for which you want to change
the name.
3 Press [ENTER].
The Title Edit window appears, which enables you to edit the name.
19
Tip: The edited name is stored in the Input Patch library.
01V96 Version 2—Owner’s Manual
Other Functions
4 Edit the name, move the cursor to the OK button, then press [ENTER].
The new name is now effective.
230
Chapter 19—Other Functions
When the Name Input Auto Copy check box (3) is on, the first four characters of a
newly-entered Long name are automatically copied to the Short name. On the other hand,
a newly-entered Short name is automatically added to the beginning of the Long name.
You can reset all port names to their default names by moving the cursor to the INITIALIZE
button, then pressing [ENTER].
Changing the Output Channel Names
To change output channel names, press the DISPLAY ACCESS [PATCH] button repeatedly
until the Patch| Out Name page appears.
The procedure for editing the names and using the Name Input Auto Copy check box and
the INITIALIZE button is the same as on the In Name page.
Setting Preferences
You can change the default settings and environmental settings of the 01V96 by using the
DIO/Setup | Prefer1 and Prefer2 pages. To locate one of the Preferences page, press the DISPLAY ACCESS [DIO/SETUP] button repeatedly.
Prefer1 page
This page enables you to set the 01V96 so that when you press a button on the top panel,
the 01V96 displays the corresponding display page, and shows or hides confirmation and
alarm messages.
01V96 Version 2—Owner’s Manual
Setting Preferences
231
This page contains the following parameters. (These parameters are explained in the order
from the top of the left column to the bottom of the right column.)
• Auto PAN Display
If this check box is on, the Pan/Route pages appear automatically when you operate the
[PAN] control in the SELECTED CHANNEL section. In Stereo Surround mode, operating
the [PAN] control enables you to adjust the left and right Pan setting. Otherwise, it enables
you to adjust the Surround Pan settings.
• Auto EQUALIZER Display
If this check box is on, the EQ | EQ Edit page appears automatically when you press an
EQ-related button in the SELECTED CHANNEL section.
• Auto SOLO Display
If this check box is on, the DIO/Setup | Monitor page appears automatically when you solo
an Input Channel.
• Auto WORD CLOCK Display
If this check box is on, the DIO/Setup | Word Clock page appears automatically if the currently-selected external wordclock source fails.
• Auto Channel Select
If this check box is on, you can select a channel by moving the corresponding fader, or by
turning on the corresponding channel [SOLO] or [ON] button.
• Store Confirmation
If this check box is on, the Title Edit window to input a Scene or library memory name
appears when you store a Scene or library memory.
• Recall Confirmation
If this check box is on, a confirmation window appears when you recall a Scene or library
memory.
• Patch Confirmation
If this check box is on, a confirmation message appears when you edit the Input and Output
Patches.
• Pair Confirmation
If this check box is on, a confirmation message appears when you create or cancel a pair.
• Nominal Pan
If this check box is checked, and when Input Channel signals are panned hard left or hard
right, the signals on the left/odd channels and right/even channels will be at the nominal
level. If this check box is not checked, these signals will be boosted by 3 dB. (When the signals are panned to center, they will be at the nominal level.) In Surround mode, the same
thing applies when any Surroound pan channel is panned hard left or right.
• Fast Meter Fall Time
If this check box is on, the level meters fall more quickly.
• MIDI Warning
If this check box is on, a warning message appears when any errors are detected in the
incoming MIDI messages.
01V96 Version 2—Owner’s Manual
19
Other Functions
• DIO Warning
If this check box is on, a warning message appears when any errors are detected in digital
audio signals received at the Slot or 2TR Digital Inputs.
232
Chapter 19—Other Functions
• Initial Data Nominal
If this check box is on, Input Channel faders and ST IN Channel level controls are set to
nominal (0 dB) when you recall Scene #0. (If this check box is off, they are set to –∞.)
• Scene MEM Auto Update
If this check box is on, you can use the Scene Memory Auto Update function (see page 169).
• Cascade COMM Link
If this check box is on, various functions and parameters are linked between cascaded
01V96s (See page 238 for more information on cascade connection). When the check box
is off, only the Solo function is linked.
• Auto Direct Out On
If this check box is on and you change the channel Direct Out destination from “–” to any
other output, the channel Direct Out is automatically enabled. If you change the channel
Direct Out destination from an output to “–,” the channel Direct Out is automatically disabled.
• Routing ST Pair Link
When this check box is checked, paired channels’ routing to the Stereo Bus will be linked.
Prefer2 page
The Prefer2 page enables you to name the channel indicated on the display, and adjust the
display brightness.
1
2
3
This page contains the following parameters:
A Channel ID/Channel
This parameter selects a style for the displayed channel. If the Channel ID check box is
selected, the Channel ID appears (e.g., CH1, CH16, AUX1). If the Channel Short Name
check box is on, the Channel Short name appears (see page 229).
B Channel Copy Parameter
•
•
•
•
This parameter selects the channel parameters to be copied when you assign the Channel Copy function to one of the User Defined buttons (see page 235). You can select
multiple options.
ALL ................................ This button selects all parameters that can be copied. When you
turn on this button, all other options are cancelled.
FADER........................... Copies the fader values.
ON.................................. Copies the on/off status of the [ON] buttons.
PAN................................ Copies the pan settings.
01V96 Version 2—Owner’s Manual
Creating a Custom Layer by Combining Channels (User Assignable Layer)
•
•
•
•
233
SURR .............................Copies the surround pan settings.
AUX................................Copies the Aux Send levels.
AUX ON ........................Copies the on/off status of the Channel to Aux signals.
EQ...................................Copies the EQ parameter values.
C Display Brightness
This parameter sets the brightness of the LED indicators in the range of 1 through 4.
Creating a Custom Layer by Combining Channels (User
Assignable Layer)
If you set the Remote Layer target to “USER ASSIGNABLE,” you can create a custom layer
by combining any 01V96 channels (excluding the Stereo Out). This custom layer is called
“User Assignable layer.”
1 Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the
DIO/Setup| Remote page appears.
2 Set the TARGET parameter to USER ASSIGNABLE, then press [ENTER].
A confirmation window appears.
3 Move the cursor to the YES button, then press [ENTER].
The 01V96 displays the page shown below.
1
4 Select the channels you wish to assign to the User Assignable layer using the
1–16 parameter boxes (1).
You can store up to four 16-channel setups in four banks by switching Banks 1–4 via the
BANK 1–4 buttons. If you press[ENTER] before selecting the channels to assign, you will
still be able to select the channels you wish to assign in the User CH Select window.
Tip: You can reset the assignment to default by moving the cursor to the CLEAR button and
pressing [ENTER].
01V96 Version 2—Owner’s Manual
19
Other Functions
5 Use the LAYER [REMOTE] button to assign or recall the User Assignable layer.
You can use the faders and [ON] buttons to control the assigned channels.
234
Chapter 19—Other Functions
Using the Oscillator
The 01V96 features an Oscillator you can use for sound checks. Follow the steps below to
use the Oscillator:
1 Press the DISPLAY ACCESS [UTILITY] button repeatedly until the Utility |
Oscillator page appears.
1
3
4
2
This page contains the following parameters:
A OSCILLATOR ON
This parameter button turns the Oscillator on or off.
B WAVEFORM
These parameter buttons select the Oscillator waveforms.
C LEVEL section
The parameter control in this section sets the Oscillator output level.
D ASSIGN section
The buttons in this section select the Oscillator output.
2 Move the cursor to the button for the Oscillator output channel in the
ASSIGN section, then press [ENTER] (you can select multiple channels).
3 Move the cursor to one of the WAVEFORM parameter buttons, then press
[ENTER].
You can select the following waveforms:
• SINE 100Hz .................. 100 Hz sinewave
• SINE 1kHz .................... 1 kHz sinewave
• SINE 10kHz .................. 10 kHz sinewave
• PINK NOISE ................ Pink noise
• BURST NOISE ............. Burst noise (200 msec pink noise pulses at four second intervals)
4 Move the cursor to the parameter control in the LEVEL section, then rotate
the Parameter wheel to set the Oscillator level to minimum.
Note: Sinewave and pink noise create unusually high sound pressure. Oscillator levels that
are too high can damage the speakers. When you use the Oscillator, be sure to set the level to
minimum, then raise the level gradually.
5 Move the cursor to the OSCILLATOR ON/OFF button, then press the [ENTER]
or [INC]/[DEC] buttons to turn on the Oscillator.
The Oscillator signal is now routed to the channels selected in the ASSIGN section.
01V96 Version 2—Owner’s Manual
Using the User Defined Keys
235
6 Move the cursor to the parameter control in the LEVEL section, then rotate
the Parameter wheel to raise the Oscillator level.
You can view the current Oscillator level on the LEVEL meter.
Using the User Defined Keys
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
You can assign any of more than 160 functions to the USER DEFINED KEYS [1]–[8]
buttons.
If you assign to one of the buttons (or “keys”) a function that is usually executed on the display pages, you can use the assigned button as a shortcut.
The Function to User Defined Keys assignments are stored in banks. Each bank accommodates an assignment of all eight buttons. (See page 249 for more information on the initial
bank settings.) The 01V96 provides eight banks (Banks A–H). Switching banks enables you
to change the assignment quickly.
Follow the steps below to assign functions to the USER DEFINED KEYS.
1 Press the USER ACCESS [UTILITY] button to locate the Utility | User Def page.
1
3
2
4
This page contains the following parameters:
A INITIALIZE
This button resets the contents of all banks to their initial settings.
B BANK
These buttons select the desired banks.
C TITILE
This parameter displays the name of the bank selected by the BANK parameter button.
Move the cursor to the TITLE parameter box, then press [ENTER]. The Title Edit window appears, enabling you to enter a name.
D 1–8
These parameter boxes enable you to assign functions to USER DEFINED KEYS
[1]–[8].
Tip: When you select a function that is executed based on specified numbers (for example, a
function that recalls a specific Scene or library memory or transmits MIDI messages), an extra
parameter box appears on the right, in which you must specify the number.
01V96 Version 2—Owner’s Manual
19
Other Functions
2 Move the cursor to the desired BANK parameter button, then press [ENTER].
The corresponding bank is selected, and the functions assigned to the User Defined buttons
in that bank are displayed in the 1–12 parameter boxes.
236
Chapter 19—Other Functions
3 Move the cursor to one of the 1–8 parameter boxes, then press [ENTER].
The 01V96 displays the User Define Select window, which enables you to assign functions
to the selected buttons.
4 Move the cursor to the left column, then rotate the Parameter wheel or press
the [INC]/[DEC] buttons to select a function you wish to assign.
A function is selected when it appears inside the dotted box. See page 247 for a complete list
of assignable functions.
5 In the same way, set the center and right column.
The items that appear in the center and right columns vary depending on the function
selected in Step 4.
6 To close the window, move the cursor to the YES button, then press [ENTER].
When the window closes, the specified function is assigned to the selected User Defined
button.
To cancel the assignment, move the cursor to the CANCEL button, then press [ENTER].
7 If you assigned functions that require numbers (such as recalling a Scene or
library memory), move the cursor to the extra parameter box shown on the
right and specify the number.
Tip:
• You can store User Defined Keys banks to a computer hard disk using the included Studio
Manager software. Be sure to back up important data.
• You can also store the assignment data to an external device, such as a MIDI data filer, by
using MIDI Bulk Dump (see page 226).
01V96 Version 2—Owner’s Manual
Using Operation Lock
237
Using Operation Lock
The 01V96 features an Operation Lock function that prevents unintentional edits and
restricts access to panel operation with a password.
To use the Operation Lock function, press the [UTILITY] button repeatedly to display the
Utility | Lock page.
1
2
3
This page contains the following parameters:
A OPERATION LOCK
This button enables or cancels Operation Lock. When you turn on this button, the Password window appears.
Enter a four-letter password using the Channel 1–10 [SEL] buttons (Channel 10 [SEL]
button enters “0”). (The password characters are represented by asterisks.) Move the
cursor to the OK button, then press [ENTER] to enable Operation Lock. The factory
default password is “1234.”
To cancel Operation Lock, press [ENTER]. The Password window appears again. Enter
the password and select the OK button. Operation Lock is cancelled.
Note: If you forget the password, you cannot cancel Operation Lock. Be sure to write down
the password.
B OPERATION LOCK SAFE section
This section enables you to select certain controls on the panel to exclude from Operation Lock. To cancel all “safe” buttons simultaneously, move the cursor to the CLEAR
ALL button, then press [ENTER].
19
Other Functions
01V96 Version 2—Owner’s Manual
238
Chapter 19—Other Functions
C PASSWORD
This button enables you to change the current password. Move the cursor to the PASSWORD button, then press [ENTER]. The Set Password window appears, enabling you
to change the password.
Enter the current password in the PASSWORD field, and a new password in the NEW
PASSWORD field. The factory default password is “1234.” Enter the new password again
in the REENTRY field located below the NEW PASSWORD field. Move the cursor to the
OK button, then press [ENTER] to change the password.
Tip: To clear the registered password, move the cursor to the CLEAR button, then press
[ENTER]. If you forget the password, initialize the password setting (see page 243).
Cascading Consoles
The 01V96 features a Cascade Bus that enables cascade connection. You can connect two
01V96s in cascade using the digital inputs and outputs, or the OMNI IN and OMNI OUT
connectors. In this way, two consoles work just like one big console, integrating each unit’s
Buses 1–8, Aux Sends 1–8, Stereo Bus, and Solo Bus.
The following functions are linked between two cascaded 01V96s via the MIDI IN and
OUT ports.
• Display page selection
• Aux selection
• Solo function
• Fader Mode
• Metering Position
• Peak Hold On/Off
• Meter Fast Fall on/off
• Scene Store, Recall, and Title Edit
Tip:
• To link functions and parameters (excluding the Solo function), turn on the Cascade
COMM Link check box on the Setup | Prefer1 page (see page 230).
• The Solo function is always linked regardless of the status of the Cascade COMM Link check
box.
• The Fader Mode will not be linked if the Master layer is selected.
01V96 Version 2—Owner’s Manual
239
Cascading Consoles
The following paragraphs explain how to make a cascade connection using two 01V96s and
the inputs and outputs of the digital I/O card installed in the slot of each 01V96.
1 Install digital I/O cards into the slot on each of two 01V96s.
2 Connect two 01V96s as follows:
• Connect the digital I/O card output on the transmitting 01V96 (slave) to the digital I/O
card input on the receiving 01V96 (master).
• Connect the ADAT IN connector on the master unit to the ADAT OUT connector on
the slave unit.
• Connect the MIDI IN port on the master unit to the MIDI OUT port on the slave unit
using a MIDI cable.
• Connect the MIDI OUT port on the master unit to the MIDI IN port on the slave unit
using a MIDI cable.
OUT
IN
MY8-AT
etc.
ADAT OUT
SLOT
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
ADAT IN
MIDI
IN/OUT
connector
SLOT
connector
connector
CH1-4
1
MY8-AT
etc.
MIDI
IN/OUT
connector
CH9-12
CH1-4
1
PHANTOM +48V
2
3
4
5
6
7
8
9
10
11
CH5-8
12
13
15
14
16
CH9-12
PHANTOM +48V
L
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
IN
INPUT
L
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
R
OUT
R
IN
INPUT
2TR
(BAL)
OUT
2TR
(BAL)
-10dBV (UNBAL)
-10dBV (UNBAL)
PHONES
INSERT
PHONES
INSERT
OUT IN
(UNBAL)
OUT IN
(UNBAL)
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
MONITOR
2TR IN
PAD
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
INSERT I/O
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
20dB
CH15/16
2TR IN
MONITOR
2TR IN
PAD
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
+4 GAIN -26
0
LEVEL
10
MONITOR
OUT
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DISPLAY ACCESS
DIO/SETUP
SCENE
13
PEAK
14 15
SIGNAL
LEVEL
10
UTILITY
PATCH
EFFECT
VIEW
RECALL
SOLO
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
-16
-60
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
PEAK
SIGNAL
DIO/SETUP
UTILITY
PATCH
EFFECT
VIEW
RECALL
PAN
DEC
-30
HIGH
Q
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
-36
HIGH
Q
-48
STEREO
HIGH-MID
HIGH-MID
FREQUENCY
HOME (METER)
LOW-MID
LAYER
ENTER
17-32
ENTER
LOW
GAIN
MASTER REMOTE
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1
2
3
4
6
8
7
10
0 +10
11
12
13
15
SEL
ON
16
0 +10
0 +10
5
10
15
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20
20
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
5
5
5
15
5
15
5
10
5
15
5
10
5
15
5
10
5
15
15
15
5
15
5
15
15
15
5
15
5
0
0
10
10
10
10
5
5
0
0
0
10
5
5
5
5
0
10
10
10
5
5
0
0
10
5
5
5
0
0
0
0
10
10
5
5
0
0
0
10
5
15
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SEL
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
5
15
30
1
2
3
4
5
6
7
8
9
10
11
13
12
14
15
2
5
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
8
7
10
0 +10
11
12
13
15
16
0 +10
0 +10
5
5
10
10
15
15
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20 10
20
20
15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30 15
30
30
20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40 20
40
40
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50 30
60 40
70
50
50
50
60
70
60
70
15
5
5
10
5
15
5
10
5
15
5
10
5
15
15
15
5
15
5
15
15
15
5
15
5
0
0
10
10
10
10
5
5
0
0
0
10
5
5
5
5
0
10
10
10
5
5
0
0
10
5
5
5
0
0
0
0
0
10
5
5
15
5
15
5
4
5
6
7
8
30
40
50
2
3
4
5
6
7
8
9
10
11
12
13
14
15
USER DEFINED
KEYS
1
2
3
4
5
6
7
8
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
AUX 8
BUS 1
BUS 2
BUS 3
BUS 4
BUS 5
BUS 6
BUS 7
BUS 8
01V96 (Slave)
ON
ST IN 2
0
20 10
5
0
15
SEL
SOLO
ON
ST IN 1
0
20 10
5
10
5
SEL
SOLO
5
5
5
5
5
5
14
0 +10
0 +10
0 +10
0 +10
5
5
5
5
5
9
0 +10
0 +10
0 +10
20 10
0
10
15
2
1
STEREO
6
0 +10
5
5
5
5
5
0 +10
ON
20 10
0
5
1
4
0 +10
SEL
10
5
USER DEFINED
KEYS
3
0 +10
0 +10
+10
3
50
1
ST IN 2
5
5
10
15
20 10
ST IN
SEL
0
10
LOW
GAIN
MASTER REMOTE
SEL
ST IN 1
0
17-32
SEL
5
5
5
5
5
5
14
0 +10
0 +10
0 +10
0 +10
5
5
5
5
5
9
0 +10
0 +10
0 +10
0 +10
5
5
5
5
5
0 +10
0 +10
0 +10
0 +10
1-16
ST IN
SEL
40
CLEAR
EQUALIZER
LOW-MID
15
SOLO
INC
-9
-15
-24
-36
LAYER
5
10
-12
FADER MODE
FREQUENCY
0
LEVEL
PHONES
PEAK
16
SIGNAL
-18
-48
5
PEAK
14 15
SIGNAL
STORE
EQ
DYNAMICS
STEREO
+10
13
0
SELECTED CHANNEL
-6
INC
EQUALIZER
HOME (METER)
1-16
10
0
-30
AUX 8
+4 GAIN -26
LEVEL
SCENE MEMORY
MIDI
PAIR/
GROUP
-24
AUX 4
AUX 7
+4 GAIN -26
0
-3
DEC
-9
AUX 3
-60
GAIN
PEAK
SIGNAL
OVER
PAN
-6
AUX 6
-16
GAIN
PEAK
SIGNAL
-18
AUX 2
-60
GAIN
PEAK
SIGNAL
PAN/
/ INSERT/
ROUTING
DELAY
-15
AUX 1
-16
GAIN
PEAK
SIGNAL
SCENE
CLEAR
-12
AUX 5
-60
GAIN
PEAK
SIGNAL
SELECTED CHANNEL
0
FADER MODE
-16
GAIN
-3
EQ
DYNAMICS
+4 GAIN -26
MONITOR
OUT
-16
DISPLAY ACCESS
STORE
+4 GAIN -26
PHONES
PEAK
16
SIGNAL
SCENE MEMORY
MIDI
PAIR/
GROUP
OVER
PAN/
/ INSERT/
ROUTING
DELAY
0
STEREO
01V96 (Master)
3 On the slave unit, press the DISPLAY ACCESS [PATCH] button repeatedly
until the Patch | Out Patch page appears.
4 Assign the Bus signals to the channels that are used for the cascade connection.
The following signals are available:
Description
Bus 1–8 Cascade Outs
CAS AUX1–AUX8
Aux Bus 1–8 Cascade Outs
CAS ST-L, CAS ST-R
Stereo Bus L & R Cascade Outs
CASSOLOL, CASSOLOR
Solo Bus L & R Cascade Outs
Other Functions
Options
CAS BUS1–BUS8
19
01V96 Version 2—Owner’s Manual
240
Chapter 19—Other Functions
The following display page is an example of integrating Bus 1–8, Aux Send 1–4, Stereo Bus,
and Solo Bus signals via the ADAT IN and OUT connectors and two 8-channel digital I/O
cards (such as MY8-AT).
Tip: Patching may vary depending on the type and number of buses used for the cascade connection.
Note: Since the number of channels available on the digital I/O card is limited, only Aux Sends
1–4 are cascaded in this example. Using a 16-channel digital I/O card (such as MY16-AT)
enables you to cascade all buses.
5 On the master unit, press the DISPLAY ACCESS [PATCH] button repeatedly
until the Patch | Cascade In page appears.
6 Select the Input Channels on the master unit to which the Bus signals are
input from the Slave unit.
The following display page is an example of receiving the slave unit’s Bus 1–8, Aux Send 1–4,
Stereo Bus, and Solo Bus signals via the ADAT IN and OUT connectors and two 8-channel
digital I/O cards (such as MY8-AT).
Note: Be sure to patch the slave Bus signals to the same Buses on the master unit. Incorrect
patching will result in an incorrect cascade connection.
7 On the master unit, press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the DIO/Setup | Cascade page appears, then adjust the Attenuators using the parameter controls.
The DIO/Setup | Cascade page enables you to adjust the level of signals input to the Cascade
Bus using the dedicated attenuators. You can also turn the Cascade Buses on or off using the
buttons below the parameter controls.
01V96 Version 2—Owner’s Manual
Cascading Consoles
241
8 Press the DISPLAY ACCESS [DIO/SETUP]
button repeatedly to display the DIO/Setup
| MIDI/Host page, then set the Cascade Link
parameter to “MIDI.”
9 Repeat Step 8 for the master unit.
After Steps 8 and 9, the slave unit will be able to transmit and receive MIDI messages.
10 To match the parameters of both 01V96s,
locate the DIO/Setup | MIDI/Host page on
the copy source unit.
Move the cursor to the TRANSMIT button
for the SYNC parameter, then press
[ENTER].
Parameters for cascade link (page 238) will be copied
to the other 01V96 via the REMOTE connector. If
you select the REQUEST button instead of the
TRANSMIT button for the SYNC parameter, you
can reverse the copy direction.
At this point, Bus 1–8, Aux 1–4, and the Stereo Bus on both 01V96s are integrated, and the
data is output via Bus Outs 1–8, Aux Outs 1–4, and the Stereo Out on the master unit. If
you solo channels on one of the 01V96s, you can monitor the soloed signals via the Monitor
outputs.
19
Other Functions
01V96 Version 2—Owner’s Manual
242
Chapter 19—Other Functions
Checking the Battery and the System Version
The Utility | Battery page enables you to check the condition of the internal memory-backup battery and the system version number. To locate this page, press the DISPLAY
ACCESS [UTILITY] button repeatedly.
1
2
A Status
If the Status is “Okay,” the battery has sufficient voltage for operation. If the Status is
“Voltage Low!,” ask your Yamaha dealer or authorized Yamaha service center to replace
the battery as soon as possible. Failure to replace a low battery may result in data loss.
Note: Do not attempt to replace the battery yourself as a malfunction may occur.
B Ver X.XX (X.XX represents the version number.)
This indicator identifies the system version number. Check the current system version
number before you update the firmware.
Visit the following website to check the latest system version number:
http://www.yamahaproaudio.com/
01V96 Version 2—Owner’s Manual
Initializing the 01V96
243
Initializing the 01V96
You can delete all currently-recorded settings and restore the factory-preset values, and reset
the Operation Lock password to its initial setting. Follow the steps below.
Note:
• If you initialize the 01V96 to the factory-preset values, all Scene, library and other data you
stored previously will be erased. Proceed with caution.
• If you want to keep the current internal data, be sure to first back up the data using the
included Studio Manager software.
Tip:
• You can also store the data to an external MIDI device, such as a MIDI data filer, by using
MIDI Bulk Dump (see page 226).
1 Make sure that the power to the 01V96 is turned off.
2 While holding down the SCENE MEMORY [STORE] button, turn on the
POWER ON/OFF switch.
After a moment, the 01V96 displays the following confirmation window.
3 To reset the 01V96 to factory default settings, move the cursor to the INITIALIZE button, then press [ENTER].
To cancel the initialization operation, move the cursor to the CANCEL button, then press
[ENTER].
When the internal data is thoroughly overwritten, the 01V96 restarts using the factory settings.
4 To reset the Operation Lock password to its initial setting, in Step 2, move
the cursor to the PASSWORD button, then press [ENTER].
The password is reset to “1234”.
If you do not take any action after the confirmation window appears, the window automatically closes and the 01V96 restarts without being initialized.
19
Other Functions
01V96 Version 2—Owner’s Manual
244
Chapter 19—Other Functions
Calibrating the Faders
The 01V96 motorized fader positions may shift over time depending on the operating conditions and environment. You can correct the shifted faders using the Calibration function.
1 Make sure that the power to the 01V96 is turned off.
2 Press and hold down the [ENTER] button, then turn on the POWER ON/OFF
switch.
After a while, the following calibration window appears.
3 Make sure that “1 FADER MOVE & FADER POSITION” is selected, then press
[ENTER].
To adjust only the motor fader movement, use the cursor buttons to select “2 FADER
MOVE ONLY,” then press [ENTER].
To adjust only the fader position, use the cursor buttons to select “3 FADER POSITION
ONLY,” then press [ENTER]. Proceed to Step 5.
To cancel the calibration operation, use the cursor buttons to select “4 QUIT,” then press
[ENTER]. The 01V96 starts in normal mode.
4 The calibration operation begins, adjusting the motor fader movement, and
the 01V96 displays a message that indicates the calibration operation is in
progress.
The calibration operation takes about two minutes. DO NOT touch the faders during the
operation.
01V96 Version 2—Owner’s Manual
Calibrating the Faders
245
5 When the calibration operation is complete, the 01V96 displays a window
in which you can select faders for position adjustment.
If you selected “2 FADER MOVE ONLY” in Step 3, the fader adjustment is complete. The
01V96 starts in normal mode.
6 Use the channel [SEL] buttons to select faders for which you wish to calibrate
the position, then press [ENTER].
The selected channel [SEL] button indicators flash. (When you press [ENTER], they light
up steadily.) At the beginning, all [SEL] buttons are flashing. However, if an error occurs
and the unit is trying calibration again, only the [SEL] button indicator of a problematic
fader flashes.
7 Follow the instruction in the window to set the position of the selected faders
to –∞, then press [ENTER].
8 Set the position of the selected faders to the level instructed in the window,
then press [ENTER]. Set faders 1-16 to –15, and Stereo fader to –30.
9 Set the position of the selected faders to the level instructed in the window,
then press [ENTER]. Set faders 1-16 to 0, and Stereo fader to any position.
10 Set the position of the selected faders to the level instructed in the window,
then press [ENTER]. Set faders 1-16 to +10, and Stereo fader to 0.
If there is no problem with the calibration result, this concludes the calibration operation.
The 01V96 will start in normal mode.
19
Other Functions
01V96 Version 2—Owner’s Manual
246
Chapter 19—Other Functions
11 If there is any problem with the calibration result, the 01V96 displays the
following window.
Also, the channel [SEL] button indicator of a problematic fader flashes.
Use the cursor buttons to select one of the following three options, then press[ENTER].
• CONTINUE..........................................While the [SEL] button indicator of a problematic fader is flashing, the calibration process
returns to Step 5.
• START FROM THE BEGINNING ....The calibration process returns to Step 2.
• QUIT ANYWAY ...................................The 01V96 cancels the calibration operation and
starts in normal mode. The standard setting will
be applied to problematic faders.
If this window appears after you try the calibration process several times, consult your nearest Yamaha dealer.
If the calibration data has some problems, the 01V96 displays the following window when
it starts up. In this case, calibrate the position of the faders specified in the window.
01V96 Version 2—Owner’s Manual
USER DEFINED KEYS
247
Appendix A: Parameter Lists
USER DEFINED KEYS
#
Function
#
Display
Function
Display
52
Input MUTE Group Enable O
IN Mute Group O
53
Input MUTE Group Enable P
IN Mute Group P
0
No Assign
No Assign
54
Output Fader Group Enable Q
OutFader Group Q
1
Scene MEM. Recall +1
Scene +1 Recall
55
Output Fader Group Enable R
OutFader Group R
2
Scene MEM. Recall –1
Scene –1 Recall
56
Output Fader Group Enable S
OutFader Group S
3
Scene MEM. Recall No. XX
Scene XX Recall
57
Output Fader Group Enable T
OutFader Group T
4
Effect-1 Lib. Recall +1
Fx1 Lib+1 Recall
58
Output MUTE Group Enable U
Out Mute Group U
5
Effect-1 Lib. Recall –1
Fx1 Lib–1 Recall
59
Output MUTE Group Enable V
Out Mute Group V
6
Effect-1 Lib. Recall No.XX
Fx1 LibXXX RCL.
60
Output MUTE Group Enable W
Out Mute Group W
7
Effect-2 Lib. Recall +1
Fx2 Lib+1 Recall
61
Output MUTE Group Enable X
Out Mute Group X
8
Effect-2 Lib. Recall –1
Fx2 Lib–1 Recall
62
Input Fader Group Assign X
IN Fader Assign X
9
Effect-2 Lib. Recall No.XX
Fx2 LibXXX RCL.
63
Input Mute Group Assign X
IN Mute Assign X
10
Effect-3 Lib. Recall +1
Fx3 Lib+1 Recall
64
Input EQ Group Assign X
IN EQ Assign x
11
Effect-3 Lib. Recall –1
Fx3 Lib–1 Recall
65
Input COMP Group Assign X
IN COMP Assign x
12
Effect-3 Lib. Recall No.XX
Fx3 LibXXX RCL.
66
Output Fader Group Assign X
OutFader Assign X
13
Effect-4 Lib. Recall +1
Fx4 Lib+1 Recall
67
Output Mute Group Assign X
Out Mute Assign X
14
Effect-4 Lib. Recall –1
Fx4 Lib–1 Recall
68
Output EQ Group Assign X
Out EQ Assign x
15
Effect-4 Lib. Recall No.XX
Fx4 LibXXX RCL.
69
Output COMP Group Assign X
Out COMP Assign x
16
Effect-1 Bypass On/Off
Fx1 Bypass
70
Input Mute Group Master X
In Mute Master X
17
Effect-2 Bypass On/Off
Fx2 Bypass
71
Output MUTE Group Master X
Out Mute Master X
18
Effect-3 Bypass On/Off
Fx3 Bypass
72
PEAK HOLD On/Off
Peak Hold
19
Effect-4 Bypass On/Off
Fx4 Bypass
73
OSCILLATOR On/Off
OSC ON/OFF
20
Channel Lib. Recall +1
CH Lib+1 Recall
74
SOLO Enable
SOLO ENABLE
21
Channel Lib. Recall –1
CH Lib–1 Recall
75
Channel Lib. Recall No. XX
CH LibXXX Recall
FADER/SOLO RELEASE Mode
On/Off
FaderSolo RELEASE
22
23
GATE Lib. Recall +1
Gate Lib+1 RCL.
76
Control Room Monitor MONO
C-R MONO
Pan / Surround Link
PAN/SURR LINK
24
GATE Lib. Recall –1
Gate Lib–1 RCL.
77
25
GATE Lib. Recall No. XX
Gate LibXXX RCL.
78
Channel Name ID/Short
CH ID/Short
Channel Copy
Channel Copy
26
COMP Lib. Recall +1
Comp Lib+1 RCL.
79
27
COMP Lib. Recall –1
Comp Lib–1 RCL.
80
Channel Paste
Channel Paste
28
COMP Lib. Recall No. XX
Comp LibXXX RCL.
81
Display Back
Display Back
29
EQ Lib. Recall +1
EQ Lib+1 Recall
82
Display Forward
Display Forward
30
EQ Lib. Recall –1
EQ Lib–1 Recall
83
UDEF KEYS BANK +1
UDEF KEYS BANK+1
EQ LibXXX Recall
84
UDEF KEYS BANK –1
UDEF KEYS BANK–1
IN Patch Lib+1
85
UDEF KEYS BANK X
UDEF KEYS BANK x
IN Patch Lib–1
86
REMOTE USER DEFINE BANK +1
RMT UDEF BANK+1
IN Patch LibXX
87
REMOTE USER DEFINE BANK -1
RMT UDEF BANK-1
REMOTE USER DEFINE BANK X
RMT UDEF BANK X
USR LAYER BANK+1
31
32
33
34
EQ Lib. Recall No. XX
Input Patch Lib. Recall +1
Input Patch Lib. Recall –1
Input Patch Lib. Recall No. XX
35
Output Patch Lib. Recall +1
Out Patch Lib+1
88
36
Output Patch Lib. Recall –1
Out Patch Lib–1
89
REMOTE USER ASS LAYER BANK +1
37
Output Patch Lib. Recall No. XX
Out Patch LibXX
90
REMOTE USER ASS LAYER BANK -1
USR LAYER BANK-1
38
Input Fader Group Enable A
IN Fader Group A
91
REMOTE USER ASS LAYER BANK X
USR LAYER BANK X
39
Input Fader Group Enable B
IN Fader Group B
92
MIDI NOTE No.XX
MIDI NOTE XXX
IN Fader Group C
93
MIDI Program change No.XX
MIDI PGM XXX
IN Fader Group D
94
MIDI Control Change No.XX
MIDI CC XXX
Machine REC
Machine REC
40
41
Input Fader Group Enable C
Input Fader Group Enable D
Input Fader Group Enable E
IN Fader Group E
43
Input Fader Group Enable F
IN Fader Group F
96
Machine PLAY
Machine PLAY
44
Input Fader Group EnableG
IN Fader Group G
97
Machine STOP
Machine STOP
45
Input Fader Group Enable H
IN Fader Group H
98
Machine FF
Machine FF
46
Input MUTE Group Enable I
IN Mute Group I
99
Machine REW
Machine REW
IN Mute Group J
100
Machine SHUTTLE
Machine SHUTTLE
Machine SCRUB
Machine SCRUB
Machine LOCATE X
47
Input MUTE Group Enable J
48
Input MUTE Group Enable K
IN Mute Group K
101
49
Input MUTE Group Enable L
IN Mute Group L
102
Machine LOCATE X
IN Mute Group M
103
Machine Set LOCATE X
Machine Capture X
IN Mute Group N
104
Machine RTZ
Machine RTZ
105
Machine Set RTZ
Machine Set RTZ
50
51
Input MUTE Group Enable M
Input MUTE Group Enable N
01V96 Version 2—Owner’s Manual
Appendix
42
95
248
Appendix A: Parameter Lists
#
Function
Display
#
Function
Display
106
Track Arming 1
Track Arming 1
165
DAW SUSPEND GROUP
107
Track Arming 2
Track Arming 2
166
DAW WINDOW TRANSPORT
DAW WIN TRANSPORT
108
Track Arming 3
Track Arming 3
167
DAW WINDOW INSERT
DAW WIN INSERT
109
Track Arming 4
Track Arming 4
168
DAW WINDOW MIX/EDIT
DAW WIN MIX/EDIT
110
Track Arming 5
Track Arming 5
169
DAW WINDOW MEM-LOC
DAW WIN MEM-LOC
111
Track Arming 6
Track Arming 6
170
DAW WINDOW STATUS
DAW WIN STATUS
112
Track Arming 7
Track Arming 7
171
DAW Shortcut UNDO
DAW UNDO
113
Track Arming 8
Track Arming 8
172
DAW Shortcut SAVE
DAW SAVE
114
Track Arming 9
Track Arming 9
173
DAW Shortcut EDIT MODE
DAW EDIT MODE
115
Track Arming 10
Track Arming 10
174
DAW Shortcut EDIT TOOL
DAW EDIT TOOL
116
Track Arming 11
Track Arming 11
175
DAW Shortcut SHIFT/ADD
DAW SHIFT/ADD
117
Track Arming 12
Track Arming 12
176
DAW Shortcut OPTION/ALL
DAW OPTION/ALL
118
Track Arming 13
Track Arming 13
177
DAW Shortcut CTRL/CLUCH
DAW CTRL/CLUCH
119
Track Arming 14
Track Arming 14
178
DAW Shortcut ALT/FINE
DAW ALT/FINE
120
Track Arming 15
Track Arming 15
179
DAW BANK +
DAW BANK +
121
Track Arming 16
Track Arming 16
180
DAW BANK –
DAW BANK –
122
Track Arming 17
Track Arming 17
181
DAW Channel +
DAW Channel +
123
Track Arming 18
Track Arming 18
182
DAW Channel –
DAW Channel –
124
Track Arming 19
Track Arming 19
183
DAW REC/RDY X
DAW REC/RDY X
125
Track Arming 20
Track Arming 20
184
DAW REC/RDY ALL
DAW REC/RDY ALL
126
Track Arming 21
Track Arming 21
185
SM CTRL Close
127
Track Arming 22
Track Arming 22
Studio Manager Window Control
Close
128
Track Arming 23
Track Arming 23
186
Studio Manager Window Control
Close All
SM CTRL Close All
129
Track Arming 24
Track Arming 24
130
Track Arming All Clear
Track Arming CLR
187
Studio Manager Window Control
Selected Channel
SM CTRL Sel Ch
131
DAW REC
DAW REC
132
DAW PLAY
DAW PLAY
188
Studio Manager Window Control
Library
SM CTRL Library
133
DAW STOP
DAW STOP
189
SM CTRL Patch
134
DAW FF
DAW FF
Studio Manager Window Control
Patch Editor
135
DAW REW
DAW REW
190
Studio Manager Window Control
Surround Editor
SM CTRL Surround
136
DAW SHUTTLE
DAW SHUTTLE
137
DAW SCRUB
DAW SCRUB
191
Studio Manager Window Control
Effect Editor
SM CTRL Effect
138
DAW AUDITION
DAW AUDITION
192
DAW PRE
DAW PRE
Studio Manager Window Control
Meter
SM CTRL Meter
139
140
DAW IN
DAW IN
193
Studio Manager Window Control
Layer
SM CTRL Layer
141
DAW OUT
DAW OUT
142
DAW POST
DAW POST
194
Studio Manager Window Control
Master
SM CTRL Master
143
DAW RTZ
DAW RTZ
144
DAW END
DAW END
145
DAW ONLINE
DAW ONLINE
146
DAW LOOP
DAW LOOP
147
DAW QUICKPUNCH
DAW QUICKPUNCH
148
DAW GROUP STATUS
DAW GROUP STATUS
149
DAW AUTO FADER
DAW AUTO FADER
150
DAW AUTO MUTE
DAW AUTO MUTE
151
DAW AUTO PAN
DAW AUTO PAN
152
DAW AUTO SEND
DAW AUTO SEND
153
DAW AUTO PLUGIN
DAW AUTO PLUGIN
154
DAW AUTO SEND MUTE
DAW AUTO SENDMUTE
155
DAW AUTO READ
DAW AUTO READ
156
DAW AUTO TOUCH
DAW AUTO TOUCH
157
DAW AUTO LATCH
DAW AUTO LATCH
158
DAW AUTO WRITE
DAW AUTO WRITE
159
DAW AUTO TRIM
DAW AUTO TRIM
160
DAW AUTO OFF
DAW AUTO OFF
161
DAW AUTO SUSPEND
DAW AUTO SUSPEND
162
DAW AUTO STATUS
DAW AUTO STATUS
163
DAW MONITOR STATUS
DAW MONI STATUS
164
DAW CREATE GROUP
DAW CREATE GROUP
01V96 Version 2—Owner’s Manual
DAW SUSPEND GRP
249
USER DEFINED KEYS Initial Assignments
USER DEFINED KEYS Initial Assignments
BANK A
BANK B
BANK C
BANK D
BANK E
BANK F
BANK G
BANK H
TITLE
Scene Recall
Group
Enable
DAW 1
DAW 2
Machine
Control
Program
Change
Special
Function
No Assign
1
Scene 1 Recall
IN Fader
Group A
UDEF BANK D UDEF BANK C
Machine
SHUTTLE
MIDI PGM 1 Display Back No Assign
2
Scene 2 Recall
IN Mute
Group I
DAW WIN
MIX/EDIT
DAW
OPTION/ALL
Machine
SCRUB
MIDI PGM 2
Display
Forward
No Assign
3
Scene 3 Recall
IN Fader
Group B
DAW BANK –
DAW AUTO
READ
Machine RTZ MIDI PGM 3
Channel
Copy
No Assign
4
Scene 4 Recall
IN Mute
Group J
DAW BANK +
DAW AUTO
TOUCH
Machine REC MIDI PGM 4
Channel
Paste
No Assign
5
Scene 5 Recall
IN Fader
Group C
DAW
SHUTTLE
DAW AUTO
LATCH
Machine
STOP
MIDI PGM 5 No Assign
No Assign
6
Scene 6 Recall
IN Mute
Group K
DAW SCRUB
DAW AUTO
WRITE
Machine
PLAY
MIDI PGM 6 No Assign
No Assign
7
Scene 7 Recall
IN Fader
Group D
DAW STOP
DAW AUTO
TRIM
Machine
REW
MIDI PGM 7 No Assign
No Assign
8
Scene 8 Recall
IN Mute
Group L
DAW PLAY
DAW AUTO
OFF
Machine FF
MIDI PGM 8 No Assign
No Assign
Input Patch Parameters
INPUT
Port ID
INSERT IN
Description
Port ID
EFFECT IN
Description
Port ID
CASCADE
Description
Port ID
Description
NONE
–
NONE
–
NONE
–
NONE
AD1
AD IN 1
AD1
AD IN 1
AUX1
AUX1
ADAT1
ADAT1 IN
AD2
AD IN 2
AD2
AD IN 2
AUX2
AUX2
ADAT2
ADAT2 IN
AD3
AD IN 3
AD3
AD IN 3
AUX3
AUX3
ADAT3
ADAT3 IN
AD4
AD IN 4
AD4
AD IN 4
AUX4
AUX4
ADAT4
ADAT4 IN
AD5
AD IN 5
AD5
AD IN 5
AUX5
AUX5
ADAT5
ADAT5 IN
AD6
AD IN 6
AD6
AD IN 6
AUX6
AUX6
ADAT6
ADAT6 IN
AD7
AD IN 7
AD7
AD IN 7
AUX7
AUX7
ADAT7
ADAT7 IN
AD8
AD IN 8
AD8
AD IN 8
AUX8
AUX8
ADAT8
ADAT8 IN
AD9
AD IN 9
AD9
AD IN 9
INS CH1
InsertOut-CH1
SL-01
Slot CH1 IN
AD10
AD IN 10
AD10
AD IN 10
INS CH2
InsertOut-CH2
SL-02
Slot CH2 IN
AD11
AD IN 11
AD11
AD IN 11
INS CH3
InsertOut-CH3
SL-03
Slot CH3 IN
AD12
AD IN 12
AD12
AD IN 12
INS CH4
InsertOut-CH4
SL-04
Slot CH4 IN
AD13
AD IN 13
AD13
AD IN 13
INS CH5
InsertOut-CH5
SL-05
Slot CH5 IN
AD14
AD IN 14
AD14
AD IN 14
INS CH6
InsertOut-CH6
SL-06
Slot CH6 IN
AD15
AD IN 15
AD15
AD IN 15
INS CH7
InsertOut-CH7
SL-07
Slot CH7 IN
AD16
AD IN 16
AD16
AD IN 16
INS CH8
InsertOut-CH8
SL-08
Slot CH8 IN
ADAT1
ADAT1 IN
ADAT1
ADAT1 IN
INS CH9
InsertOut-CH9
SL-09
Slot CH9 IN
ADAT2
ADAT2 IN
ADAT2
ADAT2 IN
INS CH10 InsertOut-CH10
SL-10
Slot CH10 IN
ADAT3
ADAT3 IN
ADAT3
ADAT3 IN
INS CH11 InsertOut-CH11
SL-11
Slot CH11 IN
ADAT4
ADAT4 IN
ADAT4
ADAT4 IN
INS CH12 InsertOut-CH12
SL-12
Slot CH12 IN
ADAT5
ADAT5 IN
ADAT5
ADAT5 IN
INS CH13 InsertOut-CH13
SL-13
Slot CH13 IN
ADAT6
ADAT6 IN
ADAT6
ADAT6 IN
INS CH14 InsertOut-CH14
SL-14
Slot CH14 IN
ADAT7
ADAT7 IN
ADAT7
ADAT7 IN
INS CH15 InsertOut-CH15
SL-15
Slot CH15 IN
ADAT8
ADAT8 IN
ADAT8
ADAT8 IN
INS CH16 InsertOut-CH16
SL-16
Slot CH16 IN
SL-01
Slot CH1 IN
SL-01
Slot CH1 IN
INS CH17 InsertOut-CH17
AD1
AD IN 1
SL-02
Slot CH2 IN
SL-02
Slot CH2 IN
INS CH18 InsertOut-CH18
AD2
AD IN 2
SL-03
Slot CH3 IN
SL-03
Slot CH3 IN
INS CH19 InsertOut-CH19
AD3
AD IN 3
SL-04
Slot CH4 IN
SL-04
Slot CH4 IN
INS CH20 InsertOut-CH20
AD4
AD IN 4
SL-05
Slot CH5 IN
SL-05
Slot CH5 IN
INS CH21 InsertOut-CH21
AD5
AD IN 5
SL-06
Slot CH6 IN
SL-06
Slot CH6 IN
INS CH22 InsertOut-CH22
AD6
AD IN 6
01V96 Version 2—Owner’s Manual
Appendix
–
250
Appendix A: Parameter Lists
INPUT
Port ID
INSERT IN
Description
Port ID
Description
EFFECT IN
Port ID
Description
CASCADE
Port ID
Description
SL-07
Slot CH7 IN
SL-07
Slot CH7 IN
INS CH23 InsertOut-CH23
AD7
AD IN 7
SL-08
Slot CH8 IN
SL-08
Slot CH8 IN
INS CH24 InsertOut-CH24
AD8
AD IN 8
SL-09
Slot CH9 IN
SL-09
Slot CH9 IN
INS CH25 InsertOut-CH25
AD9
AD IN 9
SL-10
Slot CH10 IN
SL-10
Slot CH10 IN
INS CH26 InsertOut-CH26
AD10
AD IN 10
SL-11
Slot CH11 IN
SL-11
Slot CH11 IN
INS CH27 InsertOut-CH27
AD11
AD IN 11
SL-12
Slot CH12 IN
SL-12
Slot CH12 IN
INS CH28 InsertOut-CH28
AD12
AD IN 12
SL-13
Slot CH13 IN
SL-13
Slot CH13 IN
INS CH29 InsertOut-CH29
AD13
AD IN 13
SL-14
Slot CH14 IN
SL-14
Slot CH14 IN
INS CH30 InsertOut-CH30
AD14
AD IN 14
SL-15
Slot CH15 IN
SL-15
Slot CH15 IN
INS CH31 InsertOut-CH31
AD15
AD IN 15
SL-16
Slot CH16 IN
SL-16
Slot CH16 IN
INS CH32 InsertOut-CH32
AD16
AD IN 16
FX1-1
Effect1 OUT 1
FX1-1
Effect1 OUT 1
INS BUS1
InsertOut-BUS1
2TD-L
2TR IN Dig. L
FX1-2
Effect1 OUT 2
FX1-2
Effect1 OUT 2
INS BUS2
InsertOut-BUS2
2TD-R
2TR IN Dig. R
FX2-1
Effect2 OUT 1
FX2-1
Effect2 OUT 1
INS BUS3
InsertOut-BUS3
FX2-2
Effect2 OUT 2
FX2-2
Effect2 OUT 2
INS BUS4
InsertOut-BUS4
FX3-1
Effect3 OUT 1
FX3-1
Effect3 OUT 1
INS BUS5
InsertOut-BUS5
FX3-2
Effect3 OUT 2
FX3-2
Effect3 OUT 2
INS BUS6
InsertOut-BUS6
FX4-1
Effect4 OUT 1
FX4-1
Effect4 OUT 1
INS BUS7
InsertOut-BUS7
FX4-2
Effect4 OUT 2
FX4-2
Effect4 OUT 2
INS BUS8
InsertOut-BUS8
2TD-L
2TR IN Dig. L
2TD-L
2TR IN Dig. L
INS AUX1 InsertOut-AUX1
2TD-R
2TR IN Dig. R
2TD-R
2TR IN Dig. R
INS AUX2 InsertOut-AUX2
INS AUX3 InsertOut-AUX3
INS AUX4 InsertOut-AUX4
INS AUX5 InsertOut-AUX5
INS AUX6 InsertOut-AUX6
INS AUX7 InsertOut-AUX7
INS AUX8 InsertOut-AUX8
01V96 Version 2—Owner’s Manual
INS ST-L
InsertOut-ST-L
INS ST-R
InsertOut-ST-R
Initial Input Patch Settings
251
Initial Input Patch Settings
CHANNEL
EFFECT IN PATCH
1
AD1
1-1
AUX1
2
AD2
1-2
NONE
3
AD3
2-1
AUX2
4
AD4
2-2
NONE
5
AD5
3-1
AUX3
6
AD6
3-2
NONE
7
AD7
4-1
AUX4
8
AD8
4-2
NONE
9
AD9
10
AD10
11
AD11
12
AD12
13
AD13
14
AD14
15
AD15
16
AD16
17
ADAT1
18
ADAT2
19
ADAT3
20
ADAT4
21
ADAT5
22
ADAT6
23
ADAT7
24
ADAT8
25
S-1
26
S-2
27
S-3
28
S-4
29
S-5
30
S-6
31
S-7
32
S-8
CASCADE IN PATCH
BUS1
NONE
BUS2
NONE
BUS3
NONE
BUS4
NONE
BUS5
NONE
BUS6
NONE
BUS7
NONE
BUS8
NONE
AUX1
NONE
AUX2
NONE
AUX3
NONE
AUX4
NONE
AUX5
NONE
AUX6
NONE
AUX7
NONE
AUX8
NONE
ST L
NONE
ST R
NONE
SOLO L
NONE
SOLO R
NONE
EFFECT TYPE
STI1L
FX1-1
EFFECT1
REVERB HALL
STI1R
FX1-2
EFFECT2
REVERB ROOM
STI2L
FX2-1
EFFECT3
REVERB STAGE
STI2R
FX2-2
EFFECT4
REVERB PLATE
STI3L
FX3-1
STI3R
FX3-2
STI4L
FX4-1
STI4R
FX4-2
(mono input)
Appendix
01V96 Version 2—Owner’s Manual
252
Appendix A: Parameter Lists
CHANNEL NAME
CHANNEL ID
SHORT
LONG
CH1
CH1
CH1
CH1
CH2
CH2
CH2
CH2
CH3
CH3
CH3
CH3
CH4
CH4
CH4
CH4
CH5
CH5
CH5
CH5
CH6
CH6
CH6
CH6
CH7
CH7
CH7
CH7
CH8
CH8
CH8
CH8
CH9
CH9
CH9
CH9
CH10
CH10
CH10
CH10
CH11
CH11
CH11
CH11
CH12
CH12
CH12
CH12
CH13
CH13
CH13
CH13
CH14
CH14
CH14
CH14
CH15
CH15
CH15
CH15
CH16
CH16
CH16
CH16
CH17
CH17
CH17
CH17
CH18
CH18
CH18
CH18
CH19
CH19
CH19
CH19
CH20
CH20
CH20
CH20
CH21
CH21
CH21
CH21
CH22
CH22
CH22
CH22
CH23
CH23
CH23
CH23
CH24
CH24
CH24
CH24
CH25
CH25
CH25
CH25
CH26
CH26
CH26
CH26
CH27
CH27
CH27
CH27
CH28
CH28
CH28
CH28
CH29
CH29
CH29
CH29
CH30
CH30
CH30
CH30
CH31
CH31
CH31
CH31
CH32
CH32
CH32
CH32
ST IN1
STI1
STI1
STEREO IN1
ST IN2
STI2
STI2
STEREO IN2
ST IN3
STI3
STI3
STEREO IN3
ST IN4
STI4
STI4
STEREO IN4
01V96 Version 2—Owner’s Manual
Output Patch Parameters
253
Output Patch Parameters
SLOT, ADAT, OMNI
Source
Description
INSERT IN
Source
Description
DIRECT OUT
Source
2TR OUT Digital
Description
Source
Description
–
NONE
–
NONE
–
NONE
–
NONE
BUS1
BUS1
AD1
AD IN 1
ADAT1
ADAT1 OUT
BUS1
BUS1
BUS2
BUS2
AD2
AD IN 2
ADAT2
ADAT2 OUT
BUS2
BUS2
BUS3
BUS3
AD3
AD IN 3
ADAT3
ADAT3 OUT
BUS3
BUS3
BUS4
BUS4
AD4
AD IN 4
ADAT4
ADAT4 OUT
BUS4
BUS4
BUS5
BUS5
AD5
AD IN 5
ADAT5
ADAT5 OUT
BUS5
BUS5
BUS6
BUS6
AD6
AD IN 6
ADAT6
ADAT6 OUT
BUS6
BUS6
BUS7
BUS7
AD7
AD IN 7
ADAT7
ADAT7 OUT
BUS7
BUS7
BUS8
BUS8
AD8
AD IN 8
ADAT8
ADAT8 OUT
BUS8
BUS8
AUX1
AUX1
AD9
AD IN 9
SL-01
Slot CH1 IN
AUX1
AUX1
AUX2
AUX2
AD10
AD IN 10
SL-02
Slot CH2 IN
AUX2
AUX2
AUX3
AUX3
AD11
AD IN 11
SL-03
Slot CH3 IN
AUX3
AUX3
AUX4
AUX4
AD12
AD IN 12
SL-04
Slot CH4 IN
AUX4
AUX4
AUX5
AUX5
AD13
AD IN 13
SL-05
Slot CH5 IN
AUX5
AUX5
AUX6
AUX6
AD14
AD IN 14
SL-06
Slot CH6 IN
AUX6
AUX6
AUX7
AUX7
AD15
AD IN 15
SL-07
Slot CH7 IN
AUX7
AUX7
AUX8
AUX8
AD16
AD IN 16
SL-08
Slot CH8 IN
AUX8
AUX8
ST L
STEREO L
ADAT1
ADAT1 IN
SL-09
Slot CH9 IN
ST L
STEREO L
STEREO R
ADAT2
ADAT2 IN
SL-10
Slot CH10 IN
ST R
STEREO R
INS CH1
InsertOut-CH1
ADAT3
ADAT3 IN
SL-11
Slot CH11 IN
INS CH1
InsertOut-CH1
INS CH2
InsertOut-CH2
ADAT4
ADAT4 IN
SL-12
Slot CH12 IN
INS CH2
InsertOut-CH2
INS CH3
InsertOut-CH3
ADAT5
ADAT5 IN
SL-13
Slot CH13 IN
INS CH3
InsertOut-CH3
INS CH4
InsertOut-CH4
ADAT6
ADAT6 IN
SL-14
Slot CH14 IN
INS CH4
InsertOut-CH4
INS CH5
InsertOut-CH5
ADAT7
ADAT7 IN
SL-15
Slot CH15 IN
INS CH5
InsertOut-CH5
INS CH6
InsertOut-CH6
ADAT8
ADAT8 IN
SL-16
Slot CH16 IN
INS CH6
InsertOut-CH6
INS CH7
InsertOut-CH7
SL-01
Slot CH1 IN
OMNI1
OMNI OUT 1
INS CH7
InsertOut-CH7
INS CH8
InsertOut-CH8
SL-02
Slot CH2 IN
OMNI2
OMNI OUT 2
INS CH8
InsertOut-CH8
INS CH9
InsertOut-CH9
SL-03
Slot CH3 IN
OMNI3
OMNI OUT 3
INS CH9
InsertOut-CH9
INS CH10
InsertOut-CH10
SL-04
Slot CH4 IN
OMNI4
OMNI OUT 4
INS CH10
InsertOut-CH10
INS CH11
InsertOut-CH11
SL-05
Slot CH5 IN
2TD-L
2TR OUT Dig. L
INS CH11
InsertOut-CH11
INS CH12
InsertOut-CH12
SL-06
Slot CH6 IN
2TD-R
2TR OUT Dig. R
INS CH12
InsertOut-CH12
INS CH13
InsertOut-CH13
SL-07
Slot CH7 IN
—
—
INS CH13
InsertOut-CH13
INS CH14
InsertOut-CH14
SL-08
Slot CH8 IN
—
—
INS CH14
InsertOut-CH14
INS CH15
InsertOut-CH15
SL-09
Slot CH9 IN
—
—
INS CH15
InsertOut-CH15
INS CH16
InsertOut-CH16
SL-10
Slot CH10 IN
—
—
INS CH16
InsertOut-CH16
INS CH17
InsertOut-CH17
SL-11
Slot CH11 IN
—
—
INS CH17
InsertOut-CH17
INS CH18
InsertOut-CH18
SL-12
Slot CH12 IN
—
—
INS CH18
InsertOut-CH18
INS CH19
InsertOut-CH19
SL-13
Slot CH13 IN
—
—
INS CH19
InsertOut-CH19
INS CH20
InsertOut-CH20
SL-14
Slot CH14 IN
—
—
INS CH20
InsertOut-CH20
INS CH21
InsertOut-CH21
SL-15
Slot CH15 IN
—
—
INS CH21
InsertOut-CH21
INS CH22
InsertOut-CH22
SL-16
Slot CH16 IN
—
—
INS CH22
InsertOut-CH22
INS CH23
InsertOut-CH23
FX1-1
Effect1 OUT 1
—
—
INS CH23
InsertOut-CH23
INS CH24
InsertOut-CH24
FX1-2
Effect1 OUT 2
—
—
INS CH24
InsertOut-CH24
INS CH25
InsertOut-CH25
FX2-1
Effect2 OUT 1
—
—
INS CH25
InsertOut-CH25
INS CH26
InsertOut-CH26
FX2-2
Effect2 OUT 2
—
—
INS CH26
InsertOut-CH26
INS CH27
InsertOut-CH27
FX3-1
Effect3 OUT 1
—
—
INS CH27
InsertOut-CH27
INS CH28
InsertOut-CH28
FX3-2
Effect3 OUT 2
—
—
INS CH28
InsertOut-CH28
INS CH29
InsertOut-CH29
FX4-1
Effect4 OUT 1
—
—
INS CH29
InsertOut-CH29
INS CH30
InsertOut-CH30
FX4-2
Effect4 OUT 2
—
—
INS CH30
InsertOut-CH30
INS CH31
InsertOut-CH31
2TD-L
2TR IN Dig. L
—
—
INS CH31
InsertOut-CH31
INS CH32
InsertOut-CH32
2TD-R
2TR IN Dig. R
—
—
INS CH32
InsertOut-CH32
01V96 Version 2—Owner’s Manual
Appendix
ST R
254
Appendix A: Parameter Lists
SLOT, ADAT, OMNI
Source
Description
INS BUS1
INS BUS2
INSERT IN
DIRECT OUT
Source
Description
Source
Description
InsertOut-BUS1
—
—
—
InsertOut-BUS2
—
—
—
INS BUS3
InsertOut-BUS3
—
—
INS BUS4
InsertOut-BUS4
—
INS BUS5
InsertOut-BUS5
INS BUS6
InsertOut-BUS6
INS BUS7
2TR OUT Digital
Source
Description
—
INS BUS1
InsertOut-BUS1
—
INS BUS2
InsertOut-BUS2
—
—
INS BUS3
InsertOut-BUS3
—
—
—
INS BUS4
InsertOut-BUS4
—
—
—
—
INS BUS5
InsertOut-BUS5
—
—
—
—
INS BUS6
InsertOut-BUS6
InsertOut-BUS7
—
—
—
—
INS BUS7
InsertOut-BUS7
INS BUS8
InsertOut-BUS8
—
—
—
—
INS BUS8
InsertOut-BUS8
INS AUX1
InsertOut-AUX1
—
—
—
—
INS AUX1
InsertOut-AUX1
INS AUX2
InsertOut-AUX2
—
—
—
—
INS AUX2
InsertOut-AUX2
INS AUX3
InsertOut-AUX3
—
—
—
—
INS AUX3
InsertOut-AUX3
INS AUX4
InsertOut-AUX4
—
—
—
—
INS AUX4
InsertOut-AUX4
INS AUX5
InsertOut-AUX5
—
—
—
—
INS AUX5
InsertOut-AUX5
INS AUX6
InsertOut-AUX6
—
—
—
—
INS AUX6
InsertOut-AUX6
INS AUX7
InsertOut-AUX7
—
—
—
—
INS AUX7
InsertOut-AUX7
INS AUX8
InsertOut-AUX8
—
—
—
—
INS AUX8
InsertOut-AUX8
INS ST-L
InsertOut-STL
—
—
—
—
INS ST-L
InsertOut-ST-L
INS ST-R
InsertOut-STR
—
—
—
—
INS ST-R
InsertOut-ST-R
CAS BUS1
Cascade Out Bus1
—
—
—
—
CAS BUS1
Cascade Out Bus1
CAS BUS2
Cascade Out Bus2
—
—
—
—
CAS BUS2
Cascade Out Bus2
CAS BUS3
Cascade Out Bus3
—
—
—
—
CAS BUS3
Cascade Out Bus3
CAS BUS4
Cascade Out Bus4
—
—
—
—
CAS BUS4
Cascade Out Bus4
CAS BUS5
Cascade Out Bus5
—
—
—
—
CAS BUS5
Cascade Out Bus5
CAS BUS6
Cascade Out Bus6
—
—
—
—
CAS BUS6
Cascade Out Bus6
CAS BUS7
Cascade Out Bus7
—
—
—
—
CAS BUS7
Cascade Out Bus7
CAS BUS8
Cascade Out Bus8
—
—
—
—
CAS BUS8
Cascade Out Bus8
CAS AUX1
Cascade Out Aux1
—
—
—
—
CAS AUX1
Cascade Out Aux1
CAS AUX2
Cascade Out Aux2
—
—
—
—
CAS AUX2
Cascade Out Aux2
CAS AUX3
Cascade Out Aux3
—
—
—
—
CAS AUX3
Cascade Out Aux3
CAS AUX4
Cascade Out Aux4
—
—
—
—
CAS AUX4
Cascade Out Aux4
CAS AUX5
Cascade Out Aux5
—
—
—
—
CAS AUX5
Cascade Out Aux5
CAS AUX6
Cascade Out Aux6
—
—
—
—
CAS AUX6
Cascade Out Aux6
CAS AUX7
Cascade Out Aux7
—
—
—
—
CAS AUX7
Cascade Out Aux7
CAS AUX8
Cascade Out Aux8
—
—
—
—
CAS AUX8
Cascade Out Aux8
CAS ST-L
Cascade STEREO-L
—
—
—
—
CAS ST-L
Cascade STEREO-L
CAS ST-R
Cascade STEREO-R
—
—
—
—
CAS ST-R
Cascade STEREO-R
CASSOLOL Cascade SOLO L
—
—
—
—
CASSOLOL Cascade SOLO L
CASSOLOR Cascade SOLO R
—
—
—
—
CASSOLOR Cascade SOLO R
01V96 Version 2—Owner’s Manual
255
Initial Output Patch Settings
Initial Output Patch Settings
SLOT
17
NONE
BUS1
18
NONE
BUS2
19
NONE
BUS3
20
NONE
BUS4
21
NONE
SLOT1-5
BUS5
22
NONE
SLOT1-6
BUS6
23
NONE
BUS7
24
NONE
BUS8
25
NONE
BUS1
26
NONE
BUS2
27
NONE
BUS3
28
NONE
BUS4
29
NONE
SLOT1-13
BUS5
30
NONE
SLOT1-14
BUS6
31
NONE
SLOT1-15
BUS7
32
NONE
SLOT1-16
BUS8
SLOT1-1
SLOT1-2
SLOT1-3
SLOT1-4
SLOT1-7
SLOT1-8
SLOT1-9
SLOT1-10
SLOT1-11
SLOT1-12
ADAT OUT
2TR OUT Digital
1L
ST L
1R
ST R
1
BUS1
2
BUS2
3
BUS3
4
BUS4
5
BUS5
AUX1
AUX1
AUX1
AUX1
6
BUS6
AUX2
AUX2
AUX2
AUX2
7
BUS7
AUX3
AUX3
AUX3
AUX3
8
BUS8
AUX4
AUX4
AUX4
AUX4
AUX5
AUX5
AUX5
AUX5
AUX6
AUX6
AUX6
AUX6
AUX7
AUX7
AUX7
OMNI OUT
CHANNEL NAME
CHANNEL ID
SHORT
LONG
1
AUX1
AUX7
2
AUX2
AUX8
AUX8
AUX8
AUX8
3
AUX3
BUS1
BUS1
BUS1
BUS1
4
AUX4
BUS2
BUS2
BUS2
BUS2
BUS3
BUS3
BUS3
BUS3
BUS4
BUS4
BUS4
BUS4
BUS5
BUS5
BUS5
BUS5
DIRECT OUT
1
ADAT1
BUS6
BUS6
BUS6
BUS6
2
ADAT2
BUS7
BUS7
BUS7
BUS7
3
ADAT3
BUS8
BUS8
BUS8
BUS8
4
ADAT4
STEREO
ST
ST
STEREO
5
ADAT5
6
ADAT6
7
ADAT7
8
ADAT8
SLOT-1
10
SLOT-2
11
SLOT-3
12
SLOT-4
13
SLOT-5
14
SLOT-6
15
SLOT-7
16
SLOT-8
Appendix
9
01V96 Version 2—Owner’s Manual
256
Appendix A: Parameter Lists
User Defined Remote Layer Initial Bank Settings
Bank 1 (GM Vol & Pan)
ID
Name
Short
Long
RM01 GM01 GM-CH01 VOL&PAN
RM02 GM02 GM-CH02 VOL&PAN
RM03 GM03 GM-CH03 VOL&PAN
RM04 GM04 GM-CH04 VOL&PAN
RM05 GM05 GM-CH05 VOL&PAN
RM06 GM06 GM-CH06 VOL&PAN
RM07 GM07 GM-CH07 VOL&PAN
RM08 GM08 GM-CH08 VOL&PAN
RM09 GM09 GM-CH09 VOL&PAN
RM10 GM10 GM-CH10 VOL&PAN
RM11 GM11 GM-CH11 VOL&PAN
RM12 GM12 GM-CH12 VOL&PAN
RM13 GM13 GM-CH13 VOL&PAN
RM14 GM14 GM-CH14 VOL&PAN
RM15 GM15 GM-CH15 VOL&PAN
RM16 GM16 GM-CH16 VOL&PAN
01V96 Version 2—Owner’s Manual
Controller
Data Format
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ON
END
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
FADER
B0
–
–
–
–
–
–
–
–
–
–
–
–
ON
END
–
–
–
–
–
–
–
–
–
–
–
–
FADER
B1
ON
END
FADER
B2
ON
END
FADER
B3
ON
END
FADER
B4
ON
END
FADER
B5
ON
END
FADER
B6
ON
END
FADER
B7
ON
END
FADER
B8
ON
END
FADER
B9
ON
END
FADER
BA
ON
END
FADER
BB
ON
END
FADER
BC
ON
END
FADER
BD
ON
END
FADER
BE
ON
END
FADER
BF
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
257
User Defined Remote Layer Initial Bank Settings
Bank 2 (GM Vol & Effect 1)
ID
Name
Short
Long
RM01 GM01 GM-CH01 VOL&EFF1
RM02 GM02 GM-CH02 VOL&EFF1
RM03 GM03 GM-CH03 VOL&EFF1
RM04 GM04 GM-CH04 VOL&EFF1
RM05 GM05 GM-CH05 VOL&EFF1
RM06 GM06 GM-CH06 VOL&EFF1
RM07 GM07 GM-CH07 VOL&EFF1
RM08 GM08 GM-CH08 VOL&EFF1
RM09 GM09 GM-CH09 VOL&EFF1
RM10 GM10 GM-CH10 VOL&EFF1
RM11 GM11 GM-CH11 VOL&EFF1
RM12 GM12 GM-CH12 VOL&EFF1
RM13 GM13 GM-CH13 VOL&EFF1
RM14 GM14 GM-CH14 VOL&EFF1
RM15 GM15 GM-CH15 VOL&EFF1
RM16 GM16 GM-CH16 VOL&EFF1
Controller
Data Format
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ON
END
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
FADER
B0
–
–
–
–
–
–
–
–
–
–
–
–
ON
END
–
–
–
–
–
–
–
–
–
–
–
–
FADER
B1
ON
END
FADER
B2
ON
END
FADER
B3
ON
END
FADER
B4
ON
END
FADER
B5
ON
END
FADER
B6
ON
END
FADER
B7
ON
END
FADER
B8
ON
END
FADER
B9
ON
END
FADER
BA
ON
END
FADER
BB
ON
END
FADER
BC
ON
END
FADER
BD
ON
END
FADER
BE
ON
END
FADER
BF
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
–
07
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Appendix
01V96 Version 2—Owner’s Manual
258
Appendix A: Parameter Lists
Bank 3 (XG Vol & Pan)
ID
Name
Short
RM01 XG01
RM02 XG02
RM03 XG03
RM04 XG04
RM05 XG05
RM06 XG06
RM07 XG07
RM08 XG08
RM09 XG09
RM10 XG10
RM11 XG11
RM12 XG12
RM13 XG13
RM14 XG14
RM15 XG15
RM16 XG16
Long
XG-CH01 VOL&PAN
XG-CH02 VOL&PAN
XG-CH03 VOL&PAN
XG-CH04 VOL&PAN
XG-CH05 VOL&PAN
XG-CH06 VOL&PAN
XG-CH07 VOL&PAN
XG-CH08 VOL&PAN
XG-CH09 VOL&PAN
XG-CH10 VOL&PAN
XG-CH11 VOL&PAN
XG-CH12 VOL&PAN
XG-CH13 VOL&PAN
XG-CH14 VOL&PAN
XG-CH15 VOL&PAN
XG-CH16 VOL&PAN
01V96 Version 2—Owner’s Manual
Controller
Data Format
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ON
END
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
FADER
F0
43
10
4C
08
00
0B
END
–
–
–
–
–
–
ON
END
–
–
–
–
–
–
–
–
–
–
–
–
–
43
10
4C
08
01
0B
–
–
–
–
–
–
43
10
4C
08
02
0B
–
–
–
–
–
–
43
10
4C
08
03
0B
–
–
–
–
–
–
43
10
4C
08
04
0B
–
–
–
–
–
–
43
10
4C
08
05
0B
–
–
–
–
–
–
43
10
4C
08
06
0B
–
–
–
–
–
–
43
10
4C
08
07
0B
–
–
–
–
–
–
43
10
4C
08
08
0B
–
–
–
–
–
–
43
10
4C
08
09
0B
–
–
–
–
–
–
43
10
4C
08
0A
0B
–
–
–
–
–
–
43
10
4C
08
0B
0B
–
–
–
–
–
–
43
10
4C
08
0C
0B
–
–
–
–
–
–
43
10
4C
08
0D
0B
–
–
–
–
–
–
43
10
4C
08
0E
0B
–
–
–
–
–
–
43
10
4C
08
0F
0B
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
ON
END
FADER
F0
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
–
–
FAD F7
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
–
–
–
–
–
–
–
END
–
–
–
–
–
–
259
User Defined Remote Layer Initial Bank Settings
Bank 4 (Nuendo VST Mixer)
ID
Name
Short
RM01 CH1
RM02 CH2
RM03 CH3
RM04 CH4
RM05 CH5
RM06 CH6
RM07 CH7
RM08 CH8
RM09 CH9
RM10 CH10
RM11 CH11
RM12 CH12
RM13 CH13
RM14 CH14
RM15 CH15
RM16 CH16
Long
VST MIXER CH1
VST MIXER CH2
VST MIXER CH3
VST MIXER CH4
VST MIXER CH5
VST MIXER CH6
VST MIXER CH7
VST MIXER CH8
VST MIXER CH9
VST MIXER CH10
VST MIXER CH11
VST MIXER CH12
VST MIXER CH13
VST MIXER CH14
VST MIXER CH15
VST MIXER CH16
Controller
Data Format
1
2
3
4
5
6
7
ON
B0
40
SW
8
9
10
11
12
13
14
15
16
END
–
–
–
–
–
–
–
–
–
–
–
FADER
B0
–
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
ON
B1
–
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B1
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B2
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B2
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B3
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B3
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B4
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B4
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B5
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B5
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B6
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B6
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B7
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B7
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B8
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B8
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
B9
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
B9
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
BA
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
BA
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
BB
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
BB
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
BC
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
BC
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
BD
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
BD
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
BE
40
SW
–
–
–
–
–
–
–
–
–
–
–
–
END
FADER
BE
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
ON
BF
40
SW
END
–
–
–
–
–
–
–
–
–
–
–
–
FADER
BF
07
FAD END
–
–
–
–
–
–
–
–
–
–
–
–
Appendix
01V96 Version 2—Owner’s Manual
260
Appendix A: Parameter Lists
Effects Parameters
REVERB HALL, REVERB ROOM,
REVERB STAGE, REVERB PLATE
One input, two output hall, room, stage, and plate
reverb simulations, all with gates.
Parameter
Range
Description
REV TIME
0.3–99.0 s
Reverb time
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
LO. RATIO
0.1–2.4
DIFF.
0–10
Reverb diffusion (left–right
reverb spread)
DENSITY
0–100%
Reverb density
E/R DLY
0.0–100.0 ms
Delay between early reflections
and reverb
Balance of early reflections and
reverb (0% = all reverb, 100% =
all early reflections)
E/R BAL.
0–100%
GATE REVERB, REVERSE GATE
One input, two output early reflections with gate,
and early reflections with reverse gate.
Parameter
TYPE
Range
Type-A, Type-B
Description
Type of early reflection simulation
ROOMSIZE 0.1–20.0
Reflection spacing
High-frequency reverb time ratio
LIVENESS
0–10
Early reflections decay characteristics (0 = dead, 10 = live)
Low-frequency reverb time ratio
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
DIFF.
0–10
Reflection diffusion (left–right
reflection spread)
DENSITY
0–100%
Reflection density
HI. RATIO
0.1–1.0
High-frequency feedback ratio
ER NUM.
1–19
Number of early reflections
FB.GAIN
–99 to +99%
Feedback gain
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
GATE LVL
OFF, –60 to 0 dB
Level at which gate kicks in
MONO DELAY
ATTACK
0–120 ms
Gate opening speed
One input, two output basic repeat delay.
HOLD
1
Gate open time
DECAY
2
Gate closing speed
1.
2.
0.02 ms–2.13 s (fs=44.1 kHz), 0.02 ms–1.96 s (fs=48 kHz),
0.01 ms–1.06 s (fs=88.2 kHz), 0.01 ms–981 ms (fs=96 kHz)
6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
EARLY REF.
One input, two output early reflections.
Parameter
TYPE
Range
S-Hall, L-Hall, Random, Revers, Plate,
Spring
Description
Type of early reflection simulation
ROOMSIZE 0.1–20.0
Reflection spacing
LIVENESS
0–10
Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
DIFF.
0–10
Reflection diffusion (left–right
reflection spread)
DENSITY
0–100%
Reflection density
ER NUM.
1–19
Number of early reflections
FB.GAIN
–99 to +99%
Feedback gain
HI. RATIO
0.1–1.0
High-frequency feedback ratio
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
01V96 Version 2—Owner’s Manual
Parameter
Range
Description
DELAY
0.0–2730.0 ms
Delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
HI. RATIO
0.1–1.0
High-frequency feedback ratio
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine DELAY
1.
(
Max. value depends on tempo setting)
Effects Parameters
261
STEREO DELAY
DELAY LCR
Two input, two output basic stereo delay.
One input, two output 3-tap delay (left, center,
right).
Range
Parameter
Description
DELAY L
0.0–1350.0 ms
Left channel delay time
Parameter
DELAY R
0.0–1350.0 ms
Right channel delay time
DELAY L
0.0–2730.0 ms
Left channel delay time
0.0–2730.0 ms
Center channel delay time
–99 to +99%
Left channel feedback (plus values for normal-phase feedback,
minus values for reverse-phase
feedback)
DELAY C
FB. G L
DELAY R
0.0–2730.0 ms
Right channel delay time
FB. DLY
0.0–2730.0 ms
Feedback delay time
Right channel feedback (plus values for normal-phase feedback,
minus values for reverse-phase
feedback)
LEVEL L
–100 to +100%
Left channel delay level
LEVEL C
–100 to +100%
Center channel delay level
LEVEL R
–100 to +100%
Right channel delay level
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
HI. RATIO
0.1–1.0
High-frequency feedback ratio
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
FB. G R
–99 to +99%
HI. RATIO
0.1–1.0
High-frequency feedback ratio
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE L
1
Used in conjunction with
TEMPO to determine left channel DELAY
NOTE R
1
Used in conjunction with
TEMPO to determine right channel DELAY
1.
Range
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE L
1
Used in conjunction with
TEMPO to determine DELAY L
NOTE C
1
Used in conjunction with
TEMPO to determine DELAY C
NOTE R
1
Used in conjunction with
TEMPO to determine DELAY R
NOTE FB
1
Used in conjunction with
TEMPO to determine FB. DLY
(Maximum value depends on the tempo setting)
MOD. DELAY
One input, two output basic repeat delay with modulation.
Parameter
Range
Description
1.
(
Maximum value depends on the tempo setting)
Description
DELAY
0.0–2725.0 ms
Delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
HI. RATIO
0.1–1.0
High-frequency feedback ratio
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
WAVE
Sine, Tri
Modulation waveform
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
SYNC
OFF, ON
Tempo parameter sync on/off
DLY.NOTE
1
Used in conjunction with
TEMPO to determine DELAY
MOD.NOTE
2
Used in conjunction with
TEMPO to determine FREQ
1.
(
Maximum value depends on the tempo setting)
2.
Appendix
01V96 Version 2—Owner’s Manual
262
Appendix A: Parameter Lists
ECHO
FLANGE
Two input, two output stereo delay with crossed
feedback loop.
Two input, two output flange effect.
Parameter
DELAY L
0.0–1350.0 ms
Parameter
Range
Description
FREQ.
0.05–40.00 Hz
Modulation speed
Left channel delay time
DEPTH
0–100%
Modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
Range
Description
DELAY R
0.0–1350.0 ms
Right channel delay time
FB.DLY L
0.0–1350.0 ms
Left channel feedback delay time
FB.DLY R
0.0–1350.0 ms
Right channel feedback delay
time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
Sine, Tri
Modulation waveform
–99 to +99%
Left channel feedback gain (plus
values for normal-phase feedback, minus values for
reverse-phase feedback)
WAVE
FB. G L
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
Right channel feedback gain
(plus values for normal-phase
feedback, minus values for
reverse-phase feedback)
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
–99 to +99%
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
–99 to +99%
Left to right channel feedback
gain (plus values for normal-phase feedback, minus values for reverse-phase feedback)
HSH G
–12.0 to +12.0 dB
High shelving filter gain
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
–99 to +99%
Right to left channel feedback
gain (plus values for normal-phase feedback, minus values for reverse-phase feedback)
Used in conjunction with
TEMPO to determine FREQ.
FB. G R
L->R FBG
R->L FBG
1.
HI. RATIO
0.1–1.0
High-frequency feedback ratio
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
SYNC
OFF, ON
Tempo parameter sync on/off
FREQ.
0.05–40.00 Hz
Modulation speed
NOTE L
1
Used in conjunction with
TEMPO to determine DELAY L
DEPTH
0–100%
Modulation depth
0.0–500.0 ms
Modulation delay time
1
Used in conjunction with
TEMPO to determine DELAY R
MOD. DLY
WAVE
Sine, Tri
Modulation waveform
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
NOTE FBL
1
Used in conjunction with
TEMPO to determine FB.DLY L
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
NOTE FBR
1
Used in conjunction with
TEMPO to determine FB.DLY R
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
NOTE R
1.
(Maximum value depends on the tempo setting)
CHORUS
Two input, two output chorus effect.
Parameter
FREQ.
Range
0.05–40.00 Hz
Description
Modulation speed
AM DEPTH 0–100%
Amplitude modulation depth
PM DEPTH
0–100%
Pitch modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
WAVE
Sine, Tri
Modulation waveform
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
1.
01V96 Version 2—Owner’s Manual
SYMPHONIC
Two input, two output symphonic effect.
Parameter
Range
Description
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
1.
Effects Parameters
263
PHASER
HQ. PITCH
Two input, two output 16-stage phaser.
One input, two output high-quality pitch shifter
(Available for internal effects 1 and 2.).
Parameter
Range
Description
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
FB. GAIN
Parameter
Range
Description
PITCH
–12 to +12 semitones
FINE
–50 to +50 cents
Pitch shift fine
DELAY
0.0–1000.0 ms
Delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
Pitch shift precision
Pitch shift
OFFSET
0–100
Lowest phase-shifted frequency
offset
PHASE
0.00–354.38
degrees
Left and right modulation phase
balance
2, 4, 6, 8, 10, 12,
14, 16
MODE
1–10
STAGE
Number of phase shift stages
SYNC
OFF, ON
Tempo parameter sync on/off
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
NOTE
1
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
Used in conjunction with
TEMPO to determine DELAY
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
1.
1.
(Maximum value depends on the tempo setting)
DUAL PITCH
Two input, two output pitch shifter.
Parameter
Range
Description
AUTO PAN
PITCH 1
–24 to +24 semitones
Two input, two output autopanner.
FINE 1
–50 to +50 cents
Channel #1 pitch shift fine
LEVEL 1
–100 to +100%
Channel #1 level (plus values for
normal phase, minus values for
reverse phase)
PAN 1
L63 to R63
Channel #1 pan
DELAY 1
0.0–1000.0 ms
Channel #1 delay time
FB. G 1
–99 to +99%
Channel #1 feedback gain (plus
values for normal-phase feedback, minus values for
reverse-phase feedback)
PITCH 2
–24 to +24 semitones
Channel #2 pitch shift
FINE 2
–50 to +50 cents
Channel #2 pitch shift fine
LEVEL 2
–100 to +100%
Channel #2 level (plus values for
normal phase, minus values for
reverse phase)
Channel #2 pan
Parameter
Range
Description
Channel #1 pitch shift
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
DIR.
1
Panning direction
WAVE
Sine, Tri, Square
Modulation waveform
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
SYNC
OFF, ON
Tempo parameter sync on/off
PAN 2
L63 to R63
Used in conjunction with
TEMPO to determine FREQ.
DELAY 2
0.0–1000.0 ms
Channel #2 delay time
FB. G 2
–99 to +99%
Channel #2 feedback gain (plus
values for normal-phase feedback, minus values for
reverse-phase feedback)
MODE
1–10
Pitch shift precision
TREMOLO
SYNC
OFF, ON
Tempo parameter sync on/off
Two input, two output tremolo effect.
NOTE 1
1
Used in conjunction with
TEMPO to determine Channel
#1 delay
NOTE 2
1
Used in conjunction with
TEMPO to determine Channel
#2 delay
NOTE
1.
2
L<->R, L—>R, L<—R, Turn L, Turn R
2.
Parameter
Range
Description
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
WAVE
Sine, Tri, Square
Modulation waveform
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
1.
(Maximum value depends on the tempo setting)
Appendix
FREQ.
1.
01V96 Version 2—Owner’s Manual
264
Appendix A: Parameter Lists
ROTARY
AMP SIMULATE
One input, two output rotary speaker simulator.
One input, two output guitar amp simulator.
Parameter
Range
Description
Parameter
Range
Description
ROTATE
STOP, START
Rotation stop, start
AMP TYPE
1
Guitar amp simulation type
SPEED
SLOW, FAST
Rotation speed (see SLOW and
FAST parameters)
DST TYPE
SLOW
0.05–10.00 Hz
SLOW rotation speed
DST1, DST2,
OVD1, OVD2,
CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
FAST
0.05–10.00 Hz
FAST rotation speed
DRIVE
0–100
Distortion drive
DRIVE
0–100
Overdrive level
MASTER
0–100
Master volume
ACCEL
0–10
Acceleration at speed changes
BASS
0–100
Bass tone control
LOW
0–100
Low-frequency filter
MIDDLE
0–100
Middle tone control
HIGH
0–100
High-frequency filter
TREBLE
0–100
High tone control
CAB DEP
0–100%
Speaker cabinet simulation
depth
EQ F
100–8.00 kHz
Parametric equalizer frequency
EQ G
–12.0 to +12.0 dB
Parametric equalizer gain
EQ Q
10.0–0.10
Parametric equalizer bandwidth
N. GATE
0–20
Noise reduction
RING MOD.
Two input, two output ring modulator.
Parameter
Range
Description
SOURCE
OSC, SELF
Modulation source: oscillator or
input signal
OSC FREQ
0.0–5000.0 Hz
Oscillator frequency
FM FREQ.
0.05–40.00 Hz
Oscillator frequency modulation
speed
FM DEPTH
0–100%
Oscillator frequency modulation
depth
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE FM
1
Used in conjunction with
TEMPO to determine FM FREQ
1.
1.
STK-M1, STK-M2, THRASH, MIDBST, CMB-PG, CMB-VR,
CMB-DX, CMB-TW, MINI, FLAT
DYNA. FILTER
Two input, two output dynamically controlled filter.
Parameter
Range
Description
Control source: input signal or
MIDI Note On velocity
SOURCE
INPUT, MIDI
SENSE
0–100
Sensitivity
MOD. FILTER
DIR.
UP, DOWN
Upward or downward frequency change
Two input, two output modulation filter.
DECAY
1
Filter frequency change decay
speed
TYPE
LPF, HPF, BPF
Filter type
Modulation speed
OFFSET
0–100
Filter frequency offset
0–100%
Modulation depth
RESO.
0–20
Filter resonance
0.00–354.38
degrees
LEVEL
0–100
Output Level
PHASE
Left-channel modulation and
right-channel modulation phase
difference
TYPE
LPF, HPF, BPF
Filter type: low pass, high pass,
band pass
OFFSET
0–100
Filter frequency offset
DYNA. FLANGE
RESO.
0–20
Filter resonance
LEVEL
0–100
Output level
Two input, two output dynamically controlled
flanger.
Parameter
Range
FREQ.
0.05–40.00 Hz
DEPTH
Description
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ
1.
DISTORTION
One input, two output distortion effect.
Parameter
Range
Description
1.
6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
Parameter
Range
Description
Control source: input signal or
MIDI Note On velocity
SOURCE
INPUT, MIDI
SENSE
0–100
Sensitivity
DIR.
UP, DOWN
Upward or downward frequency change
DECAY
1
Decay speed
OFFSET
0–100
Delay time offset
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
DST TYPE
DST1, DST2,
OVD1, OVD2,
CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
FB.GAIN
–99 to +99%
DRIVE
0–100
Distortion drive
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
MASTER
0–100
Master volume
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
TONE
–10 to +10
Tone
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
N. GATE
0–20
Noise reduction
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
1.
01V96 Version 2—Owner’s Manual
6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
Effects Parameters
265
DYNA. PHASER
REV->CHORUS
Two input, two output dynamically controlled
phaser.
One input, two output reverb and chorus effects in
series.
Parameter
Range
Description
Parameter
Range
SOURCE
INPUT, MIDI
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
SENSE
0–100
Sensitivity
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
DIR.
UP, DOWN
Upward or downward frequency change
DIFF.
0–10
Spread
DENSITY
0–100%
Reverb density
Lowest phase-shifted frequency
offset
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
REV.BAL
0–100%
Reverb and chorused reverb balance (0% = all chorused reverb,
100% = all reverb)
Number of phase shift stages
FREQ.
0.05–40.00 Hz
DECAY
1
OFFSET
0–100
FB.GAIN
STAGE
Decay speed
–99 to +99%
2, 4, 6, 8, 10, 12,
14, 16
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
HSH F
HSH G
1.
50.0 Hz–16.0 kHz
–12.0 to +12.0 dB
High shelving filter frequency
High shelving filter gain
6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
0.3–99.0 s
Reverb time
Modulation speed
AM DEPTH 0–100%
Amplitude modulation depth
PM DEPTH
0–100%
Pitch modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
1.
REV+CHORUS
One input, two output reverb and chorus effects in
parallel.
Parameter
REV TIME
Description
Control source: input signal or
MIDI Note On velocity
Range
Description
REV TIME
0.3–99.0 s
Reverb time
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
DIFF.
0–10
Spread
REV+FLANGE
One input, two output reverb and flanger effects in
parallel.
Parameter
Range
Description
REV TIME
0.3–99.0 s
Reverb time
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
Spread
DENSITY
0–100%
Reverb density
DIFF.
0–10
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
DENSITY
0–100%
Reverb density
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
REV/CHO
0–100%
Reverb and chorus balance (0%
= all reverb, 100% = all chorus)
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
FREQ.
0.05–40.00 Hz
Modulation speed
REV/FLG
0–100%
Reverb and flange balance (0% =
all reverb, 100% = all flange)
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
AM DEPTH 0–100%
Amplitude modulation depth
PM DEPTH
0–100%
Pitch modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
1.
1.
Appendix
01V96 Version 2—Owner’s Manual
266
Appendix A: Parameter Lists
REV->FLANGE
REV->SYMPHO.
One input, two output reverb and flanger effects in
series.
One input, two output reverb and symphonic effects
in series.
Parameter
Range
REV TIME
0.3–99.0 s
INI. DLY
HI. RATIO
Description
Parameter
Range
Description
Reverb time
REV TIME
0.3–99.0 s
0.0–500.0 ms
Initial delay before reverb begins
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
0.1–1.0
High-frequency reverb time ratio
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
DIFF.
0–10
Spread
DIFF.
0–10
Spread
DENSITY
0–100%
Reverb density
DENSITY
0–100%
Reverb density
HPF
THRU,
21.2 Hz–8.00 kHz
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
REV.BAL
0–100%
Reverb and flanged reverb balance (0% = all flanged reverb,
100% = all reverb)
REV.BAL
0–100%
Reverb and symphonic reverb
balance (0% = all symphonic
reverb, 100% = all reverb)
FREQ.
0.05–40.00 Hz
Modulation speed
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
DEPTH
0–100%
Modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
MOD. DLY
0.0–500.0 ms
Modulation delay time
WAVE
Sine, Tri
Modulation waveform
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
WAVE
Sine, Tri
Modulation waveform
Used in conjunction with
TEMPO to determine FREQ.
SYNC
OFF, ON
Tempo parameter sync on/off
1
Used in conjunction with
TEMPO to determine FREQ.
NOTE
High-pass filter cutoff frequency
1.
1.
REV->PAN
One input, two output reverb and autopan effects in
parallel.
REV+SYMPHO.
One input, two output reverb and symphonic effects
in parallel.
Parameter
Reverb time
Range
Description
Parameter
Range
Description
REV TIME
0.3–99.0 s
Reverb time
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
REV TIME
0.3–99.0 s
Reverb time
DIFF.
0–10
Spread
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
DENSITY
0–100%
Reverb density
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
HPF
High-pass filter cutoff frequency
DIFF.
0–10
Spread
THRU,
21.2 Hz–8.00 kHz
DENSITY
0–100%
Reverb density
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
REV.BAL
0–100%
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
Reverb and panned reverb balance (0% = all panned reverb,
100% = all reverb)
FREQ.
0.05–40.00 Hz
Modulation speed
0–100%
Reverb and symphonic balance
(0% = all reverb, 100% = all
symphonic)
DEPTH
0–100%
Modulation depth
DIR.
1
Panning direction
LPF
REV/SYM
FREQ.
0.05–40.00 Hz
Modulation speed
WAVE
Sine, Tri, Square
Modulation waveform
DEPTH
0–100%
Modulation depth
SYNC
OFF, ON
Tempo parameter sync on/off
MOD. DLY
0.0–500.0 ms
Modulation delay time
NOTE
2
WAVE
Sine, Tri
Modulation waveform
Used in conjunction with
TEMPO to determine FREQ.
SYNC
OFF, ON
Tempo parameter sync on/off
1.
NOTE
1
Used in conjunction with
TEMPO to determine FREQ.
2.
1.
01V96 Version 2—Owner’s Manual
L<–>R, L–>R, L<–R, Turn L, Turn R
Effects Parameters
267
DELAY+ER.
DELAY->ER.
One input, two output delay and early reflections
effects in parallel.
One input, two output delay and early reflections
effects in series.
Parameter
Range
Description
Parameter
Range
Description
DELAY L
0.0–1000.0 ms
Left channel delay time
DELAY L
0.0–1000.0 ms
Left channel delay time
DELAY R
0.0–1000.0 ms
Right channel delay time
DELAY R
0.0–1000.0 ms
Right channel delay time
FB. DLY
0.0–1000.0 ms
Feedback delay time
FB. DLY
0.0–1000.0 ms
Feedback delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
HI. RATIO
0.1–1.0
High-frequency feedback ratio
HI. RATIO
0.1–1.0
High-frequency feedback ratio
HPF
THRU,
21.2 Hz–8.00 kHz
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
DLY/ER
0–100%
Delay and early reflections balance (0% = all delay, 100% = all
early reflections)
DLY.BAL
0–100%
Delay and early reflected delay
balance (0% = all early reflected
delay, 100% = all delay)
TYPE
S-Hall, L-Hall, Random, Revers, Plate,
Spring
Type of early reflection simulation
TYPE
S-Hall, L-Hall, Random, Revers, Plate,
Spring
Type of early reflection simulation
ROOMSIZE 0.1–20.0
Reflection spacing
ROOMSIZE 0.1–20.0
Reflection spacing
LIVENESS
0–10
Early reflections decay characteristics (0 = dead, 10 = live)
LIVENESS
0–10
Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
DIFF.
0–10
Spread
DIFF.
0–10
Spread
DENSITY
0–100%
Reverb density
DENSITY
0–100%
Reverb density
ER NUM.
1–19
Number of early reflections
ER NUM.
1–19
Number of early reflections
SYNC
OFF, ON
Tempo parameter sync on/off
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE L
1
Used in conjunction with
TEMPO to determine left channel DELAY L
NOTE L
1
Used in conjunction with
TEMPO to determine left channel DELAY L
NOTE R
1
Used in conjunction with
TEMPO to determine right channel DELAY R
NOTE R
1
Used in conjunction with
TEMPO to determine right channel DELAY R
NOTE FB
1
Used in conjunction with
TEMPO to determine FB. DLY
NOTE FB
1
Used in conjunction with
TEMPO to determine FB. DLY
High-pass filter cutoff frequency
1.
1.
(Maximum value depends on the tempo setting)
(Maximum value depends on the tempo setting)
Appendix
01V96 Version 2—Owner’s Manual
268
Appendix A: Parameter Lists
DELAY+REV
Parameter
One input, two output delay and reverb effects in
parallel.
Parameter
Range
Description
DELAY L
0.0–1000.0 ms
Left channel delay time
DELAY R
0.0–1000.0 ms
Right channel delay time
FB. DLY
0.0–1000.0 ms
Feedback delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
DELAY HI
0.1–1.0
Delay high-frequency feedback
ratio
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
DLY.BAL
0–100%
Delay and reverb balance (0% =
all delay, 100% = all reverb)
REV TIME
0.3–99.0 s
INI. DLY
0.0–500.0 ms
REV HI
Range
Description
NOTE L
1
Used in conjunction with
TEMPO to determine left channel DELAY L
NOTE R
*1
Used in conjunction with
TEMPO to determine right channel DELAY R
NOTE FB
*1
Used in conjunction with
TEMPO to determine FB. DLY
1.
(Maximum value depends on the tempo setting)
DIST->DELAY
One input, two output distortion and delay effects in
series.
Parameter
Range
Description
DST TYPE
DST1, DST2,
OVD1, OVD2,
CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
Reverb time
DRIVE
0–100
Distortion drive
Initial delay before reverb begins
MASTER
0–100
Master volume
0.1–1.0
High-frequency reverb time ratio
TONE
–10 to +10
Tone control
DIFF.
0–10
Spread
N. GATE
0–20
Noise reduction
DENSITY
0–100%
Reverb density
DELAY
0.0–2725.0 ms
Delay time
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE L
1
Used in conjunction with
TEMPO to determine left channel DELAY L
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
0.1–1.0
High-frequency feedback ratio
1
Used in conjunction with
TEMPO to determine right channel DELAY R
HI. RATIO
NOTE R
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
DLY.BAL
0–100%
Distortion and delay balance
(0% = all distortion, 100% = all
delayed distortion)
NOTE FB
Used in conjunction with
TEMPO to determine FB. DLY
1
1.
(Maximum value depends on the tempo setting)
DELAY->REV
One input, two output delay and reverb effects in
series.
Parameter
Range
OFF, ON
Tempo parameter sync on/off
DLY.NOTE
1
Used in conjunction with
TEMPO to determine DELAY
MOD.NOT
E
2
Used in conjunction with
TEMPO to determine FREQ.
1.
0.0–1000.0 ms
Left channel delay time
DELAY R
0.0–1000.0 ms
Right channel delay time
FB. DLY
0.0–1000.0 ms
Feedback delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
DELAY HI
0.1–1.0
Delay high-frequency feedback
ratio
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
0–100%
Delay and delayed reverb balance (0% = all delayed reverb,
100% = all delay)
(
Maximum value depends on the tempo setting)
Description
DELAY L
DLY.BAL
SYNC
2.
MULTI FILTER
Two input, two output 3-band multi-filter (24
dB/octave).
Parameter
Range
Description
TYPE 1
HPF, LPF, BPF
Filter 1 type: high pass, low pass,
band pass
TYPE 2
HPF, LPF, BPF
Filter 2 type: high pass, low pass,
band pass
TYPE 3
HPF, LPF, BPF
Filter 3 type: high pass, low pass,
band pass
FREQ. 1
28.0 Hz–16.0 kHz
Filter 1 frequency
FREQ. 2
28.0 Hz–16.0 kHz
Filter 2 frequency
REV TIME
0.3–99.0 s
Reverb time
FREQ. 3
28.0 Hz–16.0 kHz
Filter 3 frequency
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
LEVEL 1
0–100
Filter 1 level
REV HI
0.1–1.0
High-frequency reverb time ratio
LEVEL 2
0–100
Filter 2 level
DIFF.
0–10
Spread
LEVEL 3
0–100
Filter 3 level
DENSITY
0–100%
Reverb density
RESO. 1
0–20
Filter 1 resonance
SYNC
OFF, ON
Tempo parameter sync on/off
RESO. 2
0–20
Filter 2 resonance
RESO. 3
0–20
Filter 3 resonance
01V96 Version 2—Owner’s Manual
Effects Parameters
FREEZE
Parameter
One input, one output basic sampler (Available for
internal effects 1 and 2.).
Parameter
Range
REC MODE MANUAL, INPUT
REC DLY
TRG LVL
–1000 to +1000
ms
–60 to 0 dB
TRG MASK 0–1000 ms
PLY MODE
MOMENT,
CONTI., INPUT
Description
In MANUAL mode, recording is
started by pressing the REC and
PLAY buttons. In INPUT mode,
Record-Ready mode is engaged
by pressing the REC button, and
actual recording is triggered by
the input signal.
Recording delay. For plus values,
recording starts after the trigger
is received. For minus values,
recording starts before the trigger is received.
M.BAND DYNA.
Two input, two output 3-band dynamics processor,
with individual solo and gain reduction metering for
each band.
Parameter
Range
Description
LOW GAIN –96.0 to +12.0 dB
Low band level
MID GAIN
–96.0 to +12.0 dB
Mid band level
HI. GAIN
–96.0 to +12.0 dB
High band level
–10 to +10
For positive values, the threshold
of the high band is lowered and
the threshold of the low band is
increased. For negative values,
the opposite will occur. When
set to 0, all three bands are
affected the same.
Compressor threshold
Compressor ratio
1
Loop start point in milliseconds
LOOP
NUM
0–100
START
[SAMPLE]
2
END
[SAMPLE]
2
MIDI TRG
Low-pass filter cutoff frequency
CMP. RAT
LOOP
FINE
LPF
CMP. THRE 24.0 to 0.0 dB
1
1:1 to 20:1
CMP. ATK
0–120 ms
Compressor attack
CMP. REL
1
Compressor release time
CMP. KNEE 0–5
Compressor knee
LOOKUP
0.0–100.0 ms
Lookup delay
CMP. BYP
OFF, ON
Compressor bypass
L–M XOVR
21.2 Hz–8.00 kHz
Low/mid crossover frequency
M–H XOVR 21.2 Hz–8.00 kHz
Mid/high crossover frequency
SLOPE
–6 to –12 dB
Filter slope
CEILING
–6.0 to 0.0 dB,
OFF
Specifies the maximum output
level
Number of times the sample
plays
EXP. THRE
–54.0 to –24.0 dB
Expander threshold
EXP. RAT
1:1 to ∞:1
Expander ratio
Playback start point in samples
EXP. REL
1
Expander release time
EXP. BYP
OFF, ON
Expander bypass
LIM. THRE
–12.0 to 0.0 dB
Limiter threshold
LIM. ATK
0–120 ms
Limiter attack
Limiter release time
Playback end point in samples
PITCH
High-pass filter cutoff frequency
50.0 Hz–16.0 kHz,
THRU
In MOMENT mode, the sample
plays only while the that the
PLAY button is pressed. In CONT
mode, playback continues once
the PLAY button has been
pressed. The number of times
the sample plays is set using the
LOOP NUM parameter. In INPUT
mode, playback is triggered by
the input signal.
END
–12 to +12 semitones
HPF
PRESENCE
Playback end point in milliseconds
2
Description
Once playback has been triggered, subsequent triggers are
ignored for the duration of the
TRG MASK time.
Playback start point in milliseconds
LOOP
[SAMPLE]
Range
THRU,
21.2 Hz–8.00 kHz
Input trigger level (i.e., the signal level required to trigger
recording or playback)
1
START
269
Loop start point in samples
Playback pitch shift
–50 to +50 cents
Playback pitch shift fine
OFF, C1–C6, ALL
PLAY button can be triggered by
using MIDI Note on/off messages.
1.
0.0~2970.5 ms (fs=44.1 kHz), 0.0~2729.2 ms (fs=48 kHz),
0.0~2970.5 ms (fs=88.2 kHz), 0.0~2729.2 ms (fs=96 kHz)
2.
0~131000 (fs=44.1 kHz, 48 kHz), 0~262000 (fs=88.2 kHz,
96 kHz)
LIM. REL
1
LIM. BYP
OFF, ON
Limiter bypass
LIM. KNEE
0–5
Limiter knee
SOLO LOW OFF, ON
If this is on, only the low-frequency band will be output.
SOLO MID
OFF, ON
If this is on, only the mid-frequency band will be output.
SOLO
HIGH
OFF, ON
If this is on, only the high-frequency band will be output.
1.
6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
ST REVERB
Two input, two output stereo reverb.
Parameter
Range
Description
0.3–99.0 s
Reverb time
REV TYPE
Hall, Room, Stage,
Plate
Reverb type
INI. DLY
0.0–100.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
LO. RATIO
0.1–2.4
Low-frequency reverb time ratio
DIFF.
0–10
Reverb diffusion (left–right
reverb spread)
DENSITY
0–100%
Reverb density
0–100%
Balance of early reflections and
reverb (0% = all reverb, 100% =
all early reflections)
E/R BAL.
Appendix
REV TIME
Other preset effects (COMP276, COMP276S,
COMP260, COMP260S, EQUALIZER601, OPENDECK, REV-X HALL, REV-X ROOM, REV-X
PLATE) are optional Add-On Effects. For more
information on these effects, refer to the Owner’s
Manual that came with the Add-On Effects packages.
01V96 Version 2—Owner’s Manual
270
Appendix A: Parameter Lists
Effects and tempo synchronization
Some of the 01V96’s effects allow you to synchronize the effect with the tempo. There are two such types of effect; delay-type effects
and modulation-type effects. For delay-type effects, the delay time will change according to the tempo. For modulation-type effects,
the frequency of the modulation signal will change according to the tempo.
• Parameters related to tempo synchronization
The following five parameters are related to tempo synchronization.
1) SYNC 2) NOTE 3) TEMPO 4) DELAY 5) FREQ.
SYNC:.............................This is the on/off switch for tempo synchronization.
NOTE and TEMPO: .....These are the basic parameters for tempo synchronization.
DELAY and FREQ.: .......DELAY is the delay time, and FREQ. is the frequency of the modulation signal. These directly affect
the way in which the effect sound will change. DELAY is relevant only for delay-type effects, and
FREQ. is relevant only for modulation-type effects.
• How the parameters are related
Tempo synchronization uses TEMPO and NOTE to calculate a value that will be the basis for the tempo, and continues making
adjustments so that this tempo basis stays essentially the same as the DELAY (or FREQ.). This means that when TEMPO, NOTE,
and DELAY (or FREQ.) are synchronized, and you change any of these values, the other parameters will be re-set in order to
maintain the correct relationship. The parameters that are re-set and the calculation method(*a) used are as follows.
If you turn SYNC on → NOTE will be set
If you edit DELAY (or FREQ.) → NOTE will be set
In this case, the NOTE value is calculated as follows.
NOTE = DELAY (or FREQ.)/(4 x (60/TEMPO))
If you edit NOTE → DELAY (or FREQ.) will be set
In this case, the DELAY (or FREQ.) value is calculated as follows.
DELAY (or FREQ.) = NOTE x 4 x (60/TEMPO)
If you edit TEMPO → DELAY (or FREQ.) will be set
In this case, the DELAY (or FREQ.) value is calculated as follows.
DELAY (or FREQ.) = original DELAY (or FREQ.) x (previous TEMPO/new TEMPO)
Example 1: When SYNC=ON, DELAY=250 ms, TEMPO=120, you change NOTE from 8th note to quarter note
DELAY= new NOTE x 4 x (60/TEMPO)
= (1/4) x 4 x (60/120)
= 0.5 (sec)
= 500 ms
Thus, the DELAY will change from 250 ms to 500 ms.
Example 2: When SYNC=ON, DELAY=250 ms, NOTE=8th note, you change TEMPO from 120 to 121
DELAY= original DELAY x (previous TEMPO/new TEMPO)
= 250 x (120/121)
= 247.9 (ms)
Thus, the TEMPO will change from 250 ms to 247.9 ms.
*a Rounded values are used for the calculation results.
• Ranges of the NOTE and TEMPO values
The ranges of the NOTE and TEMPO values are limited by the ranges of the DELAY or FREQ. values. You cannot set NOTE or
TEMPO values that would cause DELAY or FREQ. to exceed their maximum possible values when synchronized to tempo. This
limitation also applies even when SYNC is OFF.
• Special characteristics of the TEMPO parameter
The TEMPO parameter has the following characteristics that are unlike other parameters.
• It is a common value shared by all effects
• You cannot stored it to or recall it from the Effects Library. (You can store it to and recall it from a Scene.)
This means that the TEMPO value may not necessarily be the same when an effect is recalled as when that effect was stored. Here
is an example.
Store the effect: TEMPO=120 → Change TEMPO to 60 → Recall the effect: TEMPO=60
Normally when you change the TEMPO, the DELAY (or FREQ.) will be re-set accordingly. However if the DELAY (or FREQ.)
were changed, the effect would sound differently when recalled than when it was stored. To prevent the effect from changing in
this way between store and recall, the 01V96 does not update the DELAY (or FREQ.) value when an effect is recalled, even if the
TEMPO is no longer the same as when that effect was stored.
* The NOTE parameter is calculated based on the following values.
= 1/48
= 1/24
= 1/16
= 1/12
= 3/32
= 1/8
= 1/6
= 3/16
= 1/4
= 3/8
= 1/2
= 3/4
= 1/1
= 2/1
01V96 Version 2—Owner’s Manual
Preset EQ Parameters
271
Preset EQ Parameters
#
Parameter
Title
01 Bass Drum
1
02 Bass Drum
2
03 Snare
Drum 1
04 Snare
Drum 2
05 Tom-tom 1
06 Cymbal
07 High Hat
08 Percussion
09 E. Bass 1
10 E. Bass 2
11 Syn. Bass 1
12 Syn. Bass 2
G
L-MID
H-MID
Parameter
Title
HIGH
LOW
L-MID
H-MID
HIGH
PEAKING
PEAKING
PEAKING
H.SHELF
G
+3.5 dB
–8.5 dB
+1.5 dB
+3.0 dB
224 Hz
600 Hz
3.15 kHz
5.30 kHz
PEAKING
PEAKING
PEAKING
H.SHELF
+3.5 dB
–3.5 dB
0.0 dB
+4.0 dB
14 Piano 2
F
100 Hz
265 Hz
1.06 kHz
5.30 kHz
F
Q
1.2
10
0.9
—
Q
G
PEAKING
PEAKING
PEAKING
LPF
+8.0 dB
–7.0 dB
+6.0 dB
ON
15 E. G. Clean
5.6
10
0.7
—
PEAKING
PEAKING
PEAKING
H.SHELF
G
+2.0 dB
–5.5 dB
+0.5 dB
+2.5 dB
265 Hz
400 Hz
1.32 kHz
4.50 kHz
F
80 Hz
400 Hz
2.50 kHz
12.5 kHz
F
Q
1.4
4.5
2.2
—
Q
G
PEAKING
PEAKING
PEAKING
H.SHELF
–0.5 dB
0.0 dB
+3.0 dB
+4.5 dB
F
132 Hz
1.00 kHz
3.15 kHz
5.00 kHz
Q
1.2
4.5
0.11
—
G
L.SHELF
PEAKING
PEAKING
PEAKING
+1.5 dB
–8.5 dB
+2.5 dB
+4.0 dB
F
180 Hz
335 Hz
2.36 kHz
4.00 kHz
Q
—
10
0.7
0.1
G
PEAKING
PEAKING
PEAKING
PEAKING
+2.0 dB
–7.5 dB
+2.0 dB
+1.0 dB
16 E. G.
Crunch 1
0.0 dB
+4.0 dB
+2.0 dB
140 Hz
1.00 kHz
1.90 kHz
5.60 kHz
8
4.5
0.63
9
PEAKING
PEAKING
PEAKING
H.SHELF
G
+2.5 dB
+1.5 dB
+2.5 dB
0.0 dB
F
125 Hz
450 Hz
3.35 kHz
19.0 kHz
0.0 dB
+3.5 dB
0.0 dB
3.35 kHz
12.5 kHz
670 Hz
4.50 kHz
6.30 kHz
10
1.2
0.28
Q
PEAKING
H.SHELF
0.0 dB
+3.0 dB
19 E. G. Dist. 2
–8.5 dB
+4.5 dB
+4.0 dB
4.25 kHz
12.5 kHz
425 Hz
1.06 kHz
13.2 kHz
—
8
0.9
—
Q
PEAKING
H.SHELF
–2.5 dB
+1.0 dB
+0.5 dB
F
95 Hz
425 Hz
2.80 kHz
7.50 kHz
Q
—
0.5
1
—
G
L.SHELF
PEAKING
PEAKING
H.SHELF
–4.5 dB
0.0 dB
+2.0 dB
0.0 dB
F
100 Hz
400 Hz
2.80 kHz
17.0 kHz
Q
—
4.5
0.56
—
G
L.SHELF
PEAKING
PEAKING
H.SHELF
–7.5 dB
+4.5 dB
+2.5 dB
0.0 dB
F
35.5 Hz
112 Hz
2.00 kHz
4.00 kHz
Q
—
5
4.5
—
G
PEAKING
PEAKING
PEAKING
H.SHELF
+3.0 dB
0.0 dB
+2.5 dB
+0.5 dB
F
112 Hz
112 Hz
2.24 kHz
4.00 kHz
Q
0.1
5
6.3
—
G
PEAKING
PEAKING
PEAKING
H.SHELF
+3.5 dB
+8.5 dB
0.0 dB
0.0 dB
20 A. G.
Stroke 1
0.0 dB
+1.0 dB
+4.0 dB
1.00 kHz
1.90 kHz
5.30 kHz
0.9
4.5
3.5
—
L.SHELF
PEAKING
PEAKING
H.SHELF
G
–3.5 dB
–2.0 dB
0.0 dB
+2.0 dB
F
300 Hz
750 Hz
2.00 kHz
3.55 kHz
0.0 dB
0.0 dB
+2.0 dB
1.00 kHz
4.00 kHz
6.70 kHz
—
4.5
4.5
0.12
L.SHELF
PEAKING
PEAKING
H.SHELF
G
0.0 dB
–5.5 dB
0.0 dB
+4.0 dB
F
180 Hz
355 Hz
4.00 kHz
4.25 kHz
—
7
4.5
—
PEAKING
PEAKING
PEAKING
PEAKING
G
–2.0 dB
–1.0 dB
+1.5 dB
+3.0 dB
90 Hz
850 Hz
2.12 kHz
4.50 kHz
950 Hz
4.00 kHz
12.5 kHz
0.1
8
4.5
—
Q
PEAKING
H.SHELF
0.0 dB
+1.5 dB
0.0 dB
F
125 Hz
180 Hz
1.12 kHz
12.5 kHz
Q
1.6
8
2.2
—
G
L.SHELF
PEAKING
PEAKING
H.SHELF
–6.0 dB
0.0 dB
+2.0 dB
+4.0 dB
F
95 Hz
950 Hz
3.15 kHz
7.50 kHz
Q
—
8
0.9
—
25 Male Vocal
1
2.8
2
0.7
7
PEAKING
PEAKING
PEAKING
PEAKING
G
–0.5 dB
0.0 dB
+2.0 dB
+3.5 dB
F
190 Hz
1.00 kHz
2.00 kHz
6.70 kHz
Q
26 Male Vocal
2
—
PEAKING
224 Hz
85 Hz
PEAKING
4.5
PEAKING
–0.5 dB
F
+2.5 dB
9
PEAKING
F
Q
PEAKING
—
L.SHELF
G
F
G
—
H.SHELF
106 Hz
Q
24 Brass Sec.
4
PEAKING
–2.0 dB
Q
23 A. G.
Arpeg. 2
10
PEAKING
F
Q
22 A. G.
Arpeg. 1
—
PEAKING
G
Q
21 A. G.
Stroke 2
—
H.SHELF
1.06 kHz
106 Hz
PEAKING
10
PEAKING
315 Hz
F
–4.0 dB
9
PEAKING
+6.0 dB
Q
L.SHELF
—
L.SHELF
G
F
G
—
H.SHELF
950 Hz
1.4
0.0 dB
0.16
PEAKING
355 Hz
212 Hz
PEAKING
0.4
PEAKING
+5.0 dB
F
–2.0 dB
8
L.SHELF
G
Q
L.SHELF
—
PEAKING
+4.5 dB
F
G
6.3
PEAKING
F
Q
18 E. G. Dist. 1
10
PEAKING
G
Q
17 E. G.
Crunch 2
0.18
PEAKING
0.11
4.5
0.56
0.11
PEAKING
PEAKING
PEAKING
H.SHELF
G
+2.0 dB
–5.0 dB
–2.5 dB
+4.0 dB
F
170 Hz
236 Hz
2.65 kHz
6.70 kHz
Q
0.11
10
5.6
—
01V96 Version 2—Owner’s Manual
Appendix
13 Piano 1
LOW
#
272
#
Appendix A: Parameter Lists
Parameter
Title
27 Female Vo.
1
28 Female Vo.
2
LOW
L-MID
H-MID
HIGH
PEAKING
PEAKING
PEAKING
PEAKING
G
–1.0 dB
+1.0 dB
+1.5 dB
+2.0 dB
F
118 Hz
400 Hz
2.65 kHz
6.00 kHz
Q
0.18
0.45
0.56
0.14
L.SHELF
PEAKING
PEAKING
H.SHELF
G
–7.0 dB
+1.5 dB
+1.5 dB
+2.5 dB
F
112 Hz
335 Hz
2.00 kHz
6.70 kHz
Q
29 Chorus &
Harmo
30 Total EQ 1
—
0.16
0.2
—
PEAKING
PEAKING
PEAKING
PEAKING
G
–2.0 dB
–1.0 dB
+1.5 dB
+3.0 dB
F
90 Hz
850 Hz
2.12 kHz
4.50 kHz
Q
2.8
2
0.7
7
PEAKING
PEAKING
PEAKING
H.SHELF
G
–0.5 dB
0.0 dB
+3.0 dB
+6.5 dB
F
95 Hz
950 Hz
2.12 kHz
16.0 kHz
Q
7
2.2
5.6
—
PEAKING
31 Total EQ 2
+4.0 dB
+1.5 dB
+2.0 dB
+6.0 dB
95 Hz
750 Hz
1.80 kHz
18.0 kHz
7
2.8
5.6
—
L.SHELF
PEAKING
PEAKING
H.SHELF
G
+1.5 dB
+0.5 dB
+2.0 dB
+4.0 dB
F
67 Hz
850 Hz
1.90 kHz
15.0 kHz
—
0.28
0.7
—
PEAKING
PEAKING
PEAKING
PEAKING
G
+3.5 dB
–10.0 dB
+3.5 dB
0.0 dB
F
118 Hz
315 Hz
4.25 kHz
20.0 kHz
Q
34 Snare
Drum 3
2
10
0.4
0.4
L.SHELF
PEAKING
PEAKING
PEAKING
G
0.0 dB
+2.0 dB
+3.5 dB
0.0 dB
F
224 Hz
560 Hz
4.25 kHz
4.00 kHz
Q
35 Tom-tom 2
—
4.5
2.8
0.1
L.SHELF
PEAKING
PEAKING
H.SHELF
G
–9.0 dB
+1.5 dB
+2.0 dB
0.0 dB
F
90 Hz
212 Hz
5.30 kHz
17.0 kHz
Q
36 Piano 3
—
4.5
1.2
—
PEAKING
PEAKING
PEAKING
H.SHELF
G
+4.5 dB
–13.0 dB
+4.5 dB
+2.5 dB
F
100 Hz
475 Hz
2.36 kHz
10.0 kHz
Q
37 Piano Low
8
10
9
—
PEAKING
PEAKING
PEAKING
H.SHELF
G
–5.5 dB
+1.5 dB
+6.0 dB
0.0 dB
F
190 Hz
400 Hz
6.70 kHz
12.5 kHz
Q
38 Piano High
10
6.3
2.2
—
PEAKING
PEAKING
PEAKING
PEAKING
G
–5.5 dB
+1.5 dB
+5.0 dB
+3.0 dB
F
190 Hz
400 Hz
6.70 kHz
5.60 kHz
Q
39 Fine-EQ
Cass
40 Narrator
10
6.3
2.2
0.1
L.SHELF
PEAKING
PEAKING
H.SHELF
G
–1.5 dB
0.0 dB
+1.0 dB
+3.0 dB
F
75 Hz
1.00 kHz
4.00 kHz
12.5 kHz
Q
—
4.5
1.8
—
PEAKING
PEAKING
PEAKING
H.SHELF
G
–4.0 dB
–1.0 dB
+2.0 dB
0.0 dB
F
106 Hz
710 Hz
2.50 kHz
10.0 kHz
Q
4
7
0.63
—
01V96 Version 2—Owner’s Manual
(fs = 44.1 kHz)
#
1
2
3
Title
Gate
Ducking
A. Dr. BD
Type
GATE
DUCKING
GATE
H.SHELF
F
Q
33 Bass Drum
3
PEAKING
G
Q
32 Total EQ 3
PEAKING
Preset Gate Parameters
4
A. Dr. SN
GATE
Parameter
Value
Threshold (dB)
–26
Range (dB)
–56
Attack (ms)
0
Hold (ms)
2.56
Decay (ms)
331
Threshold (dB)
–19
Range (dB)
–22
Attack (ms)
93
Hold (ms)
1.20 S
Decay (ms)
6.32 S
Threshold (dB)
–11
Range (dB)
–53
Attack (ms)
0
Hold (ms)
1.93
Decay (ms)
400
Threshold (dB)
–8
Range (dB)
–23
Attack (ms)
1
Hold (ms)
0.63
Decay (ms)
238
Preset Compressor Parameters (fs = 44.1 kHz)
Preset Compressor Parameters
#
1
Title
Comp
Type
COMP
Parameter
3
Expand
Compander
(H)
EXPAND
COMPAND-H
COMPAND-S
6
A. Dr. BD
COMP
COMPAND-H
A. Dr. SN
COMP
2
Attack (ms)
60
Attack (ms)
38
Out gain (dB)
0.0
A. Dr. SN
EXPAND
COMPAND-S
EXPAND
54
Threshold (dB)
–23
Threshold (dB)
–12
Ratio ( :1)
1.7
Ratio ( :1)
2
1
Attack (ms)
15
Out gain (dB)
4.5
Attack (ms)
Out gain (dB)
12
E. B. Finger
COMP
3.5
Knee
2
Knee
Release (ms)
70
Release (ms)
470
Threshold (dB)
–10
Threshold (dB)
–12
Ratio ( :1)
3.5
Ratio ( :1)
1.7
Attack (ms)
1
Attack (ms)
Out gain (dB)
13
E. B. Slap
COMP
0.0
6
250
2
6
Out gain (dB)
4.0
Knee
hard
Release (ms)
133
Threshold (dB)
–8
Threshold (dB)
–10
Ratio ( :1)
4
Ratio ( :1)
3.5
Attack (ms)
25
Attack (ms)
Out gain (dB)
0.0
Out gain (dB)
3.0
Width (dB)
24
Knee
hard
Release (ms)
180
Release (ms)
250
–24
Threshold (dB)
–9
Ratio ( :1)
2.5
Attack (ms)
Out gain (dB)
14
Syn. Bass
COMP
3
9
15
Piano1
COMP
5.5
9
Attack (ms)
17
Out gain (dB)
1.0
Knee
2
Knee
hard
Release (ms)
58
Release (ms)
238
Threshold (dB)
–11
Threshold (dB)
–18
Ratio ( :1)
3.5
Ratio ( :1)
3.5
1
Attack (ms)
Attack (ms)
Out gain (dB)
16
Piano2
COMP
–1.5
Out gain (dB)
Knee
7
7
6.0
2
Release (ms)
192
Release (ms)
Threshold (dB)
–17
Threshold (dB)
–8
Ratio ( :1)
2.5
Ratio ( :1)
3.5
Attack (ms)
Out gain (dB)
8
17
E. Guitar
COMP
3.5
Attack (ms)
Out gain (dB)
174
7
2.5
Knee
2
Knee
Release (ms)
12
Release (ms)
261
Threshold (dB)
–23
Attack (ms)
Out gain (dB)
4
Threshold (dB)
–10
2
Ratio ( :1)
2.5
0
Attack (ms)
18
A. Guitar
COMP
0.5
Out gain (dB)
Knee
2
151
5
1.5
2
Release (ms)
238
–11
Threshold (dB)
–8
Threshold (dB)
Ratio ( :1)
1.7
Ratio ( :1)
2
Attack (ms)
11
Attack (ms)
33
Out gain (dB)
0.0
Out gain (dB)
1.5
Width (dB)
10
Knee
Release (ms)
128
Release (ms)
749
Threshold (dB)
–20
Attack (ms)
Out gain (dB)
Knee
Release (ms)
19
Strings1
COMP
2
Threshold (dB)
–12
2
Ratio ( :1)
1.5
2
Attack (ms)
93
Out gain (dB)
1.5
5.0
2
749
20
Strings2
COMP
Knee
Release (ms)
4
1.35 S
01V96 Version 2—Owner’s Manual
Appendix
A. Dr. Tom
–3.5
Width (dB)
842
Ratio ( :1)
10
2
Out gain (dB)
Release (ms)
Release (ms)
A. Dr. SN
COMPAND-S
250
Knee
9
11
A. Dr.
OverTop
–24
Release (ms)
Ratio ( :1)
8
Value
Ratio ( :1)
Width (dB)
7
Parameter
–8
Ratio ( :1)
A. Dr. BD
Type
2.5
Threshold (dB)
5
Title
Ratio ( :1)
Release (ms)
Compander
(S)
#
Threshold (dB)
Width (dB)
4
(fs = 44.1 kHz)
Threshold (dB)
Knee
2
Value
273
274
#
21
Appendix A: Parameter Lists
Title
Strings3
Type
COMP
Parameter
BrassSection
COMP
Syn. Pad
COMP
25
26
27
28
SamplingPerc
Sampling BD
Sampling SN
Hip Comp
Solo Vocal1
COMPAND-S
COMP
COMP
COMPAND-S
COMP
COMP
2
Attack (ms)
76
Attack (ms)
1
Out gain (dB)
2.5
COMP
EXPAND
2
Out gain (dB)
Knee
2.0
2
Release (ms)
284
Threshold (dB)
–18
Threshold (dB)
–14
Ratio ( :1)
1.7
Ratio ( :1)
2.5
Attack (ms)
18
Attack (ms)
Out gain (dB)
4.0
32
Announcer
COMPAND-H
1
Out gain (dB)
1
–2.5
Width (dB)
18
Release (ms)
226
Release (ms)
180
Threshold (dB)
–13
Threshold (dB)
–9
Ratio ( :1)
2
Ratio ( :1)
3
Attack (ms)
58
Attack (ms)
20
Out gain (dB)
2.0
33
Limiter1
COMPAND-S
1
Out gain (dB)
Width (dB)
–3.0
90
Release (ms)
238
Release (ms)
Threshold (dB)
–18
Threshold (dB)
0
Ratio ( :1)
1.7
Ratio ( :1)
∞
Attack (ms)
Out gain (dB)
8
–2.5
34
Limiter2
COMP
Attack (ms)
3.90 s
0
Out gain (dB)
0.0
Width (dB)
18
Knee
hard
Release (ms)
238
Release (ms)
319
Threshold (dB)
–14
Threshold (dB)
–18
3.5
Ratio ( :1)
2
Ratio ( :1)
Attack (ms)
2
Attack (ms)
94
Out gain (dB)
2.5
Out gain (dB)
3.5
35
Total Comp1
COMP
Knee
4
Knee
hard
Release (ms)
35
Release (ms)
447
Threshold (dB)
–18
Threshold (dB)
–16
Ratio ( :1)
4
Ratio ( :1)
6
Attack (ms)
8
Attack (ms)
11
Out gain (dB)
6.0
36
Total Comp2
COMP
Out gain (dB)
8.0
Knee
hard
Knee
Release (ms)
354
Release (ms)
Threshold (dB)
–23
Ratio ( :1)
20
Attack (ms)
15
Out gain (dB)
0.0
Width (dB)
15
Release (ms)
163
Threshold (dB)
–20
Ratio ( :1)
2.5
Attack (ms)
31
Out gain (dB)
2.0
1
342
Threshold (dB)
–8
Ratio ( :1)
2.5
Attack (ms)
26
Out gain (dB)
1.5
3
331
Threshold (dB)
–9
Ratio ( :1)
1.7
Attack (ms)
39
Out gain (dB)
2.5
Knee
Release (ms)
01V96 Version 2—Owner’s Manual
Click Erase
186
Release (ms)
Chorus
31
–33
Release (ms)
Knee
30
Value
Ratio ( :1)
Release (ms)
Solo Vocal2
Parameter
1.5
Knee
29
Type
Ratio ( :1)
Knee
24
Title
Threshold (dB)
Knee
23
#
–17
Knee
22
Value
Threshold (dB)
2
226
1
180
275
Dynamics Parameters
Dynamics Parameters
The dynamics effects for each channel strip include a Gate section (only for Input Channels) and a Comp section. The Gate section includes Gate and Ducking types. The Comp
section includes Compressor, Expander, Compander Hard (COMP. (H)), and Compander
Soft (COMP. (S)) types.
GATE Section (Only for Input Channels)
GATE
A gate attenuates signals below a set THRESHOLD level by a specified amount (RANGE).
Parameter
Range
Description
THRESHOLD (dB)
–54.0 to 0.0 (541 points)
This determines the level at which the gate effect
is applied.
RANGE (dB)
–70 to 0 (71 points)
This determines the amount of attenuation when
the gate closes.
ATTACK (ms)
0–120 (121 points)
This determines how fast the gate opens when the
signal exceeds the threshold level.
HOLD (ms)
44.1kHz: 0.02 ms – 2.13 sec
48kHz: 0.02 ms – 1.96 sec
88.2kHz: 0.01 ms – 1.06 sec
96kHz: 0.01 ms – 981 ms
(160 points)
This determines how long the gate stays open
once the trigger signal has fallen below the threshold.
DECAY (ms)
44.1kHz: 6 ms – 46.0 sec
48kHz: 5 ms – 42.3 sec
88.2kHz: 3 ms – 23.0 sec
96kHz: 3 ms – 21.1 sec
(160 points)
This determines how fast the gate closes once the
hold time has expired. The value is expressed as
the duration required for the level to change by
6 dB.
I/O Characteristics
Time Series Analysis
Output Signal
THRESHOLD
Output Level
Input Level
Output Level
Input Signal
ATTACK
HOLD
DECAY
THRESHOLD
RANGE
RANGE
Input Level
Time
Time
Appendix
01V96 Version 2—Owner’s Manual
276
Appendix A: Parameter Lists
DUCKING
Ducking is commonly used for voice-over applications in which the background music
level is reduced automatically when an announcer speaks. When the KEY IN source signal
level exceeds the specified THRESHOLD, the output level is attenuated by a specified
amount (RANGE).
Parameter
Range
Description
THRESHOLD (dB)
–54.0 to 0.0 (541 points)
This determines the level of trigger signal (KEY IN)
required to activate ducking.
RANGE (dB)
–70 to 0 (71 points)
This determines the amount of attenuation when
ducking is activated.
ATTACK (ms)
0–120 (121 points)
This determines how soon the signal is ducked
once the ducker has been triggered.
HOLD (ms)
44.1kHz: 0.02 ms – 2.13 sec
48kHz: 0.02 ms – 1.96 sec
88.2kHz: 0.01 ms – 1.06 sec
96kHz: 0.01 ms – 981 ms
(160 points)
This determines how long ducking remains active
once the trigger signal has fallen below the
THRESHOLD level.
DECAY (ms)
44.1kHz: 6 ms – 46.0 sec
48kHz: 5 ms – 42.3 sec
88.2kHz: 3 ms – 23.0 sec
96kHz: 3 ms – 21.1 sec
(160 points)
This determines how soon the ducker returns to its
normal gain once the trigger signal level drops
below the threshold. The value is expressed as the
duration required for the level to change by 6 dB.
I/O Characteristics
Time Series Analysis
Output Level
Output Signal
Input Level
Output Level
Input Signal
THRESHOLD
ATTACK
HOLD
DECAY
THRESHOLD
RANGE
RANGE
Input Level
01V96 Version 2—Owner’s Manual
Time
Time
Dynamics Parameters
277
COMP Section
COMP
The COMP processor attenuates signals above a specified THRESHOLD by a specified
RATIO. The COMP processor can also be used as a limiter, which, with a RATIO of ∞:1,
reduces the level to the threshold. This means that the limiter’s output level never actually
exceeds the threshold.
Parameter
Range
Description
THRESHOLD (dB)
–54.0 to 0.0 (541 points)
This determines the level of input signal required to
trigger the compressor.
RATIO
1.0:1, 1.1:1, 1.3:1, 1.5:1,
1.7:1, 2.0:1, 2.5:1, 3.0:1,
3.5:1, 4.0:1, 5.0:1, 6.0:1,
8.0:1, 10:1, 20:1, ∞:1
(16 points)
This determines the amount of compression, that
is, the change in output signal level relative to
change in input signal level.
ATTACK (ms)
0–120 (121 points)
This determines how soon the signal will be compressed once the compressor has been triggered.
RELEASE (ms)
44.1kHz: 6 ms – 46.0 sec
48kHz: 5 ms – 42.3 sec
88.2kHz: 3 ms – 23.0 sec
96kHz: 3 ms – 21.1 sec
(160 points)
This determines how soon the compressor returns
to its normal gain once the trigger signal level
drops below the threshold. The value is expressed
as the duration required for the level to change by
6 dB.
OUT GAIN (dB)
0.0 to +18.0 (180 points)
This sets the compressor's output signal level.
KNEE
Hard, 1–5 (6 points)
This determines how compression is applied at the
threshold. For higher knee settings, compression is
applied gradually as the signal exceeds the specified threshold, creating a more natural sound.
I/O Characteristics
(KNEE=hard, OUT GAIN=0.0dB)
Time Series Analysis (RATIO=∞:1)
RATIO
Output Level
THRESHOLD
Output Signal
Input Level
Output Level
Input signal
ATTACK
RELEASE
THRESHOLD
Input Level
Time
Time
Appendix
01V96 Version 2—Owner’s Manual
278
Appendix A: Parameter Lists
EXPAND
An expander attenuates signals below a specified THRESHOLD by a specified RATIO.
Parameter
Range
Description
THRESHOLD (dB)
–54.0 to 0.0 (541 points)
This determines the level of input signal required to
trigger the expander.
RATIO
1.0:1, 1.1:1, 1.3:1, 1.5:1,
1.7:1, 2.0:1, 2.5:1, 3.0:1,
3.5:1, 4.0:1, 5.0:1, 6.0:1,
8.0:1, 10:1, 20:1, ∞:1
(16 points)
This determines the amount of expansion.
ATTACK (ms)
0–120 (121 points)
This determines how soon the expander returns to
its normal gain once the trigger signal level exceeds
the threshold.
RELEASE (ms)
44.1kHz: 6 ms – 46.0 sec
48kHz: 5 ms – 42.3 sec
88.2kHz: 3 ms – 23.0 sec
96kHz: 3 ms – 21.1 sec
(160 points)
This determines how soon the signal is expanded
once the signal level drops below the threshold.
The value is expressed as the duration required for
the level to change by 6 dB.
OUT GAIN (dB)
0.0 to +18.0 (180 points)
This sets the expander's output signal level.
Hard, 1–5 (6 points)
This determines how expansion is applied at the
threshold. For higher knee settings, expansion is
applied gradually as the signal falls below the specified threshold, creating a more natural sound.
KNEE
I/O Characteristics
(KNEE=hard, OUT GAIN=0.0dB)
Time Series Analysis (RATIO=∞:1)
Output Level
THRESHOLD
Output Signal
Input Level
Output Level
Input Signal
ATTACK
RELEASE
THRESHOLD
RATIO
Input Level
01V96 Version 2—Owner’s Manual
Time
Time
Dynamics Parameters
279
Output Level
COMPANDER HARD (H)
COMPANDER SOFT (S)
The hard and soft companders combine the effects of the compressor, expander and limiter.
THRESHOLD
0dB
Input Level
WIDTH
The companders function differently at the following levels:
1 0 dB and higher .................................... Functions as a limiter.
2 Exceeding the threshold....................... Functions as a compressor.
3 Below the threshold and width ........... Functions as an expander.
The hard compander has an expansion ratio of 5:1, while the soft compander has an expansion ratio of 1.5:1. The expander is essentially turned off when the width is set to maximum.
The compressor has a fixed knee setting of 2.
* The gain is automatically adjusted according to the ratio and threshold values, and can
be increased by up to 18 dB.
* The OUT GAIN parameter enables you to compensate for the overall level change
caused by the compression and expansion processes.
Parameter
Range
Description
THRESHOLD (dB)
–54.0 to 0.0 (541 points)
This determines the level at which compression is
applied.
RATIO
1.0:1, 1.1:1, 1.3:1, 1.5:1,
1.7:1, 2.0:1, 2.5:1, 3.0:1,
3.5:1, 4.0:1, 5.0:1, 6.0:1,
8.0:1, 10:1, 20:1, (15 points)
This determines the amount of compression.
ATTACK (ms)
0–120 (121 points)
This determines how soon the signal is compressed or expanded once the compander has
been triggered.
RELEASE (ms)
44.1kHz: 6 ms – 46.0 sec
48kHz: 5 ms – 42.3 sec
88.2kHz: 3 ms – 23.0 sec
96kHz: 3 ms – 21.1 sec
(160 points)
This determines how soon the compressor or
expander returns to the normal gain once the
trigger signal level drops below or exceeds the
threshold respectively. The value is expressed as
the duration required for the level to change by
6 dB.
OUT GAIN (dB)
–18.0 to 0.0 (180 points)
This sets the compander's output signal level.
0–90 (91 points)
This determines how far below the threshold
expansion will be applied. The expander is activated when the level drops below the threshold
and width.
WIDTH (dB)
Appendix
01V96 Version 2—Owner’s Manual
280
Appendix B: Specifications
Appendix B: Specifications
General Spec
Number of scene memories
99
Internal
Sampling Frequency
Signal Delay
External
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Normal rate: 44.1 kHz–10% to 48 kHz+6%
Double rate: 88.2 kHz–10% to 96 kHz+6%
fs=48 kHz
Less than 1.6 ms CH INPUT to STEREO OUT
fs=96 kHz
Less than 0.8 ms CH INPUT to STEREO OUT
100 mm motorized × 17
Fader
+10 to –138, –∞ dB input faders
Fader Resolution
0 to –138, –∞ dB master faders, stereo fader
Total Harmonic Distortion1
(CH INPUT to STEREO OUT)
(Input Gain=Min.)
fs=48 kHz
Less than 0.05% 20 Hz–20 kHz @ +14 dB into 600 Ω
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
fs=96 kHz
Less than 0.05% 20 Hz–40 kHz @ +14 dB into 600 Ω
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
Frequency Response
(CH INPUT to STEREO OUT)
fs=48 kHz
20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
fs=96 kHz
20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
110 dB typ. DA Converter (STEREO OUT)
Dynamic Range
(maximum level to noise level)
105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz
105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz
–128 dB Equivalent Input Noise
–86 dB residual output noise. STEREO OUT (STEREO OUT off)
Hum & Noise2
(20 Hz–20 kHz)
Rs=150 Ω
Input Gain=Max. –86 dB (90 dB S/N) STEREO OUT
Input Pad =0 dB (STEREO fader at nominal level and all CH INPUT faders at minimum level)
Input Pad =0 dB
Input Sensitivity
=–60 dB
–64 dB (68 dB S/N) STEREO OUT
(STEREO fader at nominal level and one CH INPUT fader at nominal level)
74 dB CH INPUT (CH1–12) to STEREO OUT/OMNI (BUS) OUT
40 dB CH INPUT (CH13–16) to STEREO OUT
Maximum Voltage Gain
74 dB CH INPUT (CH1–12) to OMNI (AUX) OUT (via pre input fader)
74 dB CH INPUT (CH1–12) to MONITOR OUT (via STEREO BUS)
80 dB adjacent input channels (CH1–12)
Crosstalk
(@ 1 kHz)
80 dB adjacent input channels (CH13–16)
Input Gain=Min.
AD Input (1–12)
AD Input (13–16)
80 dB input to output
Phantom switch
+48 V DC (each 4ch)
Pad switch
0/20 dB attenuation
Gain control
44 dB (–60 to –16), detented
Peak indicator
LED (red) turns on when post HA level reaches 3 dB below clipping at digital domain
Signal indicator
LED (green) turns on when post HA level reaches 20 dB below nominal at
digital domain
AD converter
24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times oversampling (fs=88.2, 96 kHz)
Gain control
30 dB (–26 to +4), detented
Peak indicator
LED (red) turns on when post HA level reaches 3 dB below clipping at digital domain
Signal indicator
LED (green) turns on when post HA level reaches 20 dB below nominal at
digital domain
AD converter
24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times oversampling (fs=88.2, 96 kHz)
Input selector
CH15/16/2TR IN for CH15/16
01V96 Version 2—Owner’s Manual
General Spec
281
Digital Input
(2TR IN DIGITAL, ADAT input)
Option Input (SLOT)
Available cards
Optional digital interface cards (MY16, MY8, MY4 series)
Input patch
—
Phase
Normal/reverse
Gate-type3
On/off
Key in: 12 ch Group (1–12, 13–24, 25–32)/AUX1–8
On/off
Comp-type4
Key in: self /Stereo Link
Pre EQ/pre fader/post fader
Attenuator
EQ
–96.0 to +12.0 dB (0.1 dB step)
4-band PEQ (TYPE1)5
On/off
Input Channel CH1–32
Delay
0–43400 samples
On/off
—
Fader
100 mm motorized (INPUT/AUX1–8)
Aux send
Solo
On/off
AUX1–8; pre fader/post fader
On/off
Pre fader/after pan
Pan
127 positions (Left= 1–63, Center, Right= 1–63)
Surround pan
127 × 127 positions
([Left= 1–63, Center, Right= 1–63] x [Front= 1–63, Center, Rear= 1–63])
LFE level
–∞, –96 dB to +10 dB (256 step)
Routing
STEREO, BUS1–8, DIRECT OUT
Direct out
Pre EQ/pre fader/post fader
Metering
Displayed on LCD
Peak hold on/off
Input patch (L/R) —
Phase (L/R)
Normal/reverse
Attenuator (L/R)
–96.0 to +12.0 dB (0.1 dB step)
Equalizer
4band PEQ (TYPE1)5
On/off
—
Fader
Aux send
Stereo Input Channel CH1–4
Solo
On/off
AUX1–8; pre fader/post fader
On/off
Pre fader/after pan
127 positions (Left= 1–63, Center, Right= 1–63)
Surround pan
(L/R)
127 × 127 positions
([Left= 1–63, Center, Right= 1–63] x [Front= 1–63, Center, Rear= 1–63])
LFE level (L/R)
–∞, –96 dB to +10 dB (256 step)
Routing
STEREO, BUS1–8, DIRECT OUT
Level
Displayed on LCD
Peak hold on/off
0 to –96 dB (1 dB step)
On/off
—
Waveform
Sine 100 Hz, sine 1 kHz, sine 10 kHz, pink noise, burst noise
Routing
BUS1–8, AUX1–8, STEREO L/R
DA converter
24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times oversampling (@fs=88.2, 96 kHz)
01V96 Version 2—Owner’s Manual
Appendix
STEREO OUT
INPUT/AUX1–8 send
Pan (L/R)
Metering
OSCILLATOR
100 mm motorized
282
Appendix B: Specifications
MONITOR OUT
DA converter
24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times oversampling (@fs=88.2, 96 kHz)
Output patch
STEREO, BUS1–8, AUX1–8, DIRECT OUT 1–32, INSERT OUT (CH1–32,
BUS1–8, AUX1–8, STEREO), CASCADE OUT (BUS1–8, AUX 1–8, STEREO,
SOLO)
DA converter
24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times oversampling (@fs=88.2, 96 kHz)
OMNI OUT 1–4
Dither
2TR OUT DIGITAL
Output patch
Dither
ADAT Output
On/off
Word length 16, 20, 24-bit
STEREO, BUS1–8, AUX 1–8, DIRECT OUT 1–32, INSERT OUT (CH 1–32,
BUS 1–8, AUX 1–8, STEREO), CASCADE OUT (BUS 1–8, AUX 1–8, STEREO,
SOLO)
On/off
Word length 16, 20, 24-bit
Output patch
STEREO, BUS1–8, AUX 1–8, DIRECT OUT 1–32, INSERT OUT (CH 1–32,
BUS 1–8, AUX 1–8, STEREO), CASCADE OUT (BUS 1–8, AUX 1–8, STEREO,
SOLO)
Available card
Optional digital interface card (MY16, MY8, MY4 series)
Dither
Option Output (SLOT)
Output patch
Comp-type4
Attenuator
EQ
On/off
Word length 16/20/24-bit
STEREO, BUS1–8, AUX 1–8, DIRECT OUT 1–32, INSERT OUT (CH 1–32,
BUS 1–8, AUX 1–8, STEREO), CASCADE OUT (BUS 1–8, AUX 1–8, STEREO,
SOLO)
On/off
Pre EQ/pre fader/post fader
–96.0 to +12.0 dB (0.1 dB step)
4-band PEQ5
On/off
STEREO
On/off
—
Fader
100 mm motorized
Balance
127 positions (Left=1–63, Center, Right=1–63)
Delay
0–29100 samples
Displayed on LCD
Metering
Peak hold on/off
12-elements x2 LED meters
Comp-type4
Attenuator
EQ
On/off
Pre EQ/pre fader/post fader
–96.0 to +12.0 dB (0.1 dB step)
4-band PEQ5
On/off
BUS1–8
On/off
—
Fader
100 mm motorized
Delay
0–29100 samples
Bus to stereo
On/off
Level (–∞, –138 dB–0 dB)
Pan: 127 positions (Left=1–63, Center, Right=1–63)
Metering
01V96 Version 2—Owner’s Manual
Displayed on LCD
Peak hold on/off
General Spec
Comp-type4
Attenuator
EQ
283
On/off
Pre EQ/pre fader/post fader
–96.0 to +12.0 dB (0.1 dB step)
4-band PEQ5
On/off
AUX1–8
On/off
—
Fader
100 mm motorized
Delay
0–29100 samples
Metering
INTERNAL EFFECTS
(EFFECT 1–4)
Power Requirements
Dimensions
Displayed on LCD
Peak hold on/off
Number of
effects
[email protected], 48kHz
Bypass
On/off
In/out
2-in, 2-out
Effect-in from
AUX1–8/INSERT OUT
[email protected], 96kHz
Effect-out to
Input patch
U.S./Canada
120 V, 60 Hz 90 W
Other
220–240 V, 50/60 Hz 90 W
(H x D x W)
150 x 548 x 436 mm
Net weight
15 kg
Operating free-air temperature range
10–35°C
Storage temperature range
–20–60°C
Supplied Accessories
AC Cable
CD-ROM (Studio Manager)
Owner’s Manual
Studio Manager Installation Guide
Options
Digital interface card (MY16, MY8, MY4 series)
RACK MOUNT KIT: RK1
1. Total harmonic distortion is measured with a 6 dB/octave filter @ 80 kHz.
2. Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave
attenuation.
3. See “Gate Parameters” on page 284.
4. See “Comp Parameters” on page 284.
5. See “EQ Parameters” on page 283.
EQ Parameters
LOW/HPF
Q
0.1–10.0
(41 points)
low shelving
HPF
F
G
L-MID
H-MID
0.1–10.0
(41 points)
HIGH /LPF
0.1–10.0
(41 points)
high shelving
LPF
21.2 Hz–20.0 kHz (1/12 oct step)
±18 dB
(0.1 dB step)
HPF: on/off
±18 dB
(0.1 dB step)
±18 dB
(0.1 dB step)
LPF: on/off
Appendix
01V96 Version 2—Owner’s Manual
284
Appendix B: Specifications
Gate Parameters
Threshold
–54 dB–0 dB (0.1 dB step)
Range
–70 dB–0 dB (1 dB step)
Attack
0 ms–120 ms (1 ms step)
0.02 ms–1.96 s (216 points) @ 48 kHz
Gate
Hold
0.02 ms–2.13 s (216 points) @ 44.1 kHz
0.01 ms–981 ms (216 points) @ 96 kHz
0.01 ms–1.06 s (216 points) @ 88.2 kHz
5 ms–42.3 s (160 points) @ 48 kHz
Decay
6 ms–46.0 s (160 points) @ 44.1 kHz
3 ms–21.1 s (160 points) @ 96 kHz
3 ms–23.0 s (160 points) @ 88.2 kHz
Threshold
–54 dB–0 dB (0.1 dB step)
Range
–70 dB–0 dB (1 dB step)
Attack
0 ms–120 ms (1 ms step)
0.02 ms–1.96 s (216 points) @ 48 kHz
Ducking
Hold
0.02 ms–2.13 s (216 points) @ 44.1 kHz
0.01 ms–981 ms (216 points) @ 96 kHz
0.01 ms–1.06 s (216 points) @ 88.2 kHz
5 ms–42.3 s (160 points) @ 48 kHz
Decay
6 ms–46.0 s (160 points) @ 44.1 kHz
3 ms–21.1 s (160 points) @ 96 kHz
3 ms–23.0 s (160 points) @ 88.2 kHz
Comp Parameters
Compressor
Threshold
–54 dB–0 dB (0.1 dB step)
Ratio (x :1)
x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞ (16 points)
Out gain
0 dB to +18 dB (0.1 dB step)
Knee
Hard, 1, 2, 3, 4, 5 (6 step)
Attack
0 ms–120 ms (1 ms step)
5 ms–42.3 s (160 points) @ 48 kHz
Release
6 ms–46.0 s (160 points) @ 44.1 kHz
3 ms–21.1 s (160 points) @ 96 kHz
3 ms–23.0 s (160 points) @ 88.2 kHz
Threshold
Expander
–54 dB to 0 dB (0.1 dB step)
Ratio (x :1)
x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞ (16 points)
Out gain
0 dB to +18 dB (0.1 dB step)
Knee
Hard, 1, 2, 3, 4, 5 (6 points)
Attack
0 ms–120 ms (1 ms step)
5 ms–42.3 s (160 points) @ 48 kHz
Release
6 ms–46.0 s (160 points) @ 44.1 kHz
3 ms–21.1 s (160 points) @ 96 kHz
3 ms–23.0 s (160 points) @ 88.2 kHz
01V96 Version 2—Owner’s Manual
Libraries
Compander H
Threshold
–54 dB to 0 dB (0.1 dB step)
Ratio (x :1)
x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points)
Out gain
–18 dB to 0 dB (0.1 dB step)
Width
1 dB–90 dB (1 dB step)
Attack
0 ms–120 ms (1 ms step)
285
5 ms–42.3 s (160 points) @ 48 kHz
Release
6 ms–46.0 s (160 points) @ 44.1 kHz
3 ms–21.1 s (160 points) @ 96 kHz
3 ms–23.0 s (160 points) @ 88.2 kHz
Compander S
Threshold
–54 dB to 0 dB (0.1 dB step)
Ratio (x :1)
x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points)
Out gain
–18 dB to 0 dB (0.1 dB step)
Width
1 dB–90 dB (1 dB step)
Attack
0 ms–120 ms (1 ms step)
5 ms–42.3 s (160 points) @ 48 kHz
Release
6 ms–46.0 s (160 points) @ 44.1 kHz
3 ms–21.1 s (160 points) @ 96 kHz
3 ms–23.0 s (160 points) @ 88.2 kHz
Libraries
Effect library (EFFECT 1–4)
Compressor library
Gate library
EQ library
Channel library
Input patch library
Output patch library
Presets
53
User memories
75
Presets
36
User memories
92
Presets
4
User memories
124
Presets
40
User memories
160
Presets
2
User memories
127
Presets
1
User memories
32
Presets
1
User memories
32
Appendix
01V96 Version 2—Owner’s Manual
286
Appendix B: Specifications
Analog Input Spec
Input
PAD
GAIN
Actual Load
Impedance
For Use With
Nominal
Sensitivity1
–60 dB
0
INPUT A/B
1–12
3k Ω
–16 dB
50–600 Ω
Mics & 600 Ω
Lines
20
–26 dB
INPUT 13–16
—
10k Ω
600 Ω Lines
+4 dB
Input level
Connector
Nominal
Max.
before clip
–70 dB
(0.245 mV)
–60 dB
(0.775 mV)
–40 dB
(7.75 mV)
–26 dB
(38.8 mV)
–16 dB
(123 mV)
+4 dB
(1.23 V)
(Balanced)2
B: Phone jack
–6 dB
(338 mV)
+4 dB
(1.23 V)
+24 dB
(12.28 V)
(TRS) (Balanced)3
–36 dB
(12.3 mV)
–26 dB
(38.8 mV)
–6 dB
(388 mV)
–6 dB
(388 mV)
+4 dB
(1.23 V)
+24 dB
(12.28 V)
(Balanced)3
A: XLR-3-31 type
Phone jack (TRS)
CH INSERT IN
1–12
—
10k Ω
600 Ω Lines
–12 dB
(195 mV)
–2 dB
(616 mV)
+18 dB
(6.16 V)
Phone jack (TRS)
2TR IN [L, R]
—
10k Ω
600 Ω Lines
–10 dBV
(316 mV)
–10 dBV
(316 mV)
+10 dBV
(3.16 V)
RCA pin jack
(Unbalanced)
(Unbalanced)4
1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit
is set to maximum gain. (All faders and level controls are maximum position.)
2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
For 2TR IN levels, 0 dBV is referenced to 1.00 Vrms.
All input AD converters (CH INPUT 1–16) are 24-bit linear, 128-times oversampling. (@fs=44.1, 48 kHz)
+48 V DC (phantom power) is supplied to CH INPUT (1–12) XLR type connectors.
Three PHANTOM +48V switches CH1–4, 5–8, 9–12 turn on the phantom power for inputs 1–4, 5–8, 9–12 respectively.
Analog Output Specs
Actual
Source
Impedance
For Use With
Nominal
STEREO OUT [L, R]
75 Ω
OMNI OUT 1–4
Output
Output level
Connector
Nominal
Max.
before clip
600 Ω Lines
+4 dB
(1.23 V)
+24 dB
(12.28 V)
XLR-3-32 type (Balanced)1
150 Ω
10k Ω Lines
+4 dB
(1.23 V)
+24 dB
(12.28 V)
Phone jack (TRS) (Balanced)2
MONITOR OUT [L, R]
150 Ω
10k Ω Lines
+4 dB
(1.23 V)
+24 dB
(12.28 V)
Phone jack (TRS) (Balanced)2
CH INSERT OUT 1–12
600 Ω
10k Ω Lines
–2 dB
(616 mV)
+18 dB
(6.16 V)
2TR OUT [L, R]
600 Ω
10k Ω Lines
–10 dBV
(316 mV)
+10 dBV
(3.16 V)
RCA Pin Jack (Unbalanced)
PHONES
100 Ω
8 Ω Phones
4 mW
25 mW
Stereo Phone Jack (TRS)
40 Ω Phones
12 mW
75 mW
(Unbalanced)4
1.
2.
3.
4.
Phone jack (TRS) (Unbalanced)3
XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).
PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND).
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
2TR OUT [L, R] levels, 0 dBV is referenced to 1.00 Vrms.
All output DA converters are 24-bit, 128-times oversampling. (@fs=44.1, 48 kHz)
01V96 Version 2—Owner’s Manual
Digital Input Spec
287
Digital Input Spec
Input
2TR IN DIGITAL
Format
Data length
IEC-60958
24-bit
ADAT1
24-bit
ADAT IN
Level
Connector
0.5 Vpp/75 Ω RCA pin jack
—
OPTICAL
1. ALESIS proprietary multichannel optical digital interface format
Digital Output Spec
Output
2TR OUT DIGITAL
Format
Data length
IEC-609581
Consumer use
24-bit3
ADAT2
24-bit3
ADAT OUT
Level
Connector
0.5V pp/75 Ω RCA pin jack
—
OPTICAL
1. Channel status of 2TR OUT DIGITAL
Type:
linear PCM
Category code: Digital signal mixer
Copy prohibit: NO
Emphasis:
NO
Clock accuracy: Level II (1000 ppm)
Sampling rate: depends on the internal configuration
2. ALESIS proprietary multichannel optical digital interface format
3. Dither: word length 16/20/24 bit
I/O SLOT Spec
Each I/O SLOT accepts a Digital interface card. SLOT1 has a serial interface.
Maker
Model
Function
INPUT
OUTPUT
1
MY8-AT
8
8
MY16-AT
16
16
MY8-TD
8
8
MY16-TD
16
16
8
8
16
16
8
8
MY8-AE
Digital I/O
MY8-AEB
MY16-AE
MY8-AE96S
MY8-AE96
Yamaha MY4-AD
MY8-AD
MY8-AD24
ANALOG IN
8
MY8-DA96
MY8ADDA96
Waves
—
ANALOG I/O
8
Can handle
24 bit/96 kHz by
double channel mode
44.1/48/88.2/96 kHz
Sampling Rate Converter for input
20 bit
44.1/48 kHz
1
4
44.1/48/88.2/96 kHz
20 bit
44.1/48 kHz
24 bit
44.1/48/88.2/96 kHz
IEEE1394
24 bit
44.1/48 kHz
ADAT
24 bit
—
24 bit
8
8
8
Effect & I/O
8
8
AP8AD
ANALOG IN
8
—
AP8DA
ANALOG OUT
—
8
Maximum 5 nodes
44.1/48 kHz
44.1/48/88.2/96 kHz
44.1/48/88.2/96 kHz
4ch @fs=88.2, 96 kHz
1. Selectable from STEREO/BUS/AUX/DIRECT/OUT/INSERT OUT/CASCADE OUT (STEREO, BUS1~8, AUX1~8, SOLO).
Details depend on each interface card.
01V96 Version 2—Owner’s Manual
Appendix
Apogee
44.1/48 kHz
AES/EBU
24 bit
16
Y96K
Note
24 bit
—
8
mLAN Interface
The
number of
Available
cards
Frequency
24 bit
16
Y56K
TASCAM
—
ANALOG OUT
MY8-mLAN
MY16mLAN
Resolution
ADAT
4
MY8-AD96
MY4-DA
Format
288
Appendix B: Specifications
CONTROL I/O Spec
I/O Port
TO HOST USB
MIDI
WORD CLOCK
Format
Level
Connector in Console
USB
0 V–3.3 V
IN1
B type USB connector
MIDI
—
DIN Connector 5P
OUT
MIDI
—
DIN Connector 5P
THRU
MIDI
—
DIN Connector 5P
IN
—
TTL/75 Ω
BNC Connector
OUT
—
TTL/75 Ω
BNC Connector
1. MIDI IN can use as TIME CODE IN MTC.
350
150
430 (Not included Screw Heads)
436 (Included Screw Heads)
Dimensions
101
350
540
548
Unit: mm
Specifications and descriptions in this owner’s manual are for information purposes only.
Yamaha Corp. reserves the right to change or modify products or specifications at any time
without prior notice. Since specifications, equipment or options may not be the same in
every locale, please check with your Yamaha dealer.
European Models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 20 A
Conforms to Environments: E1, E2, E3 and E4
01V96 Version 2—Owner’s Manual
Scene Memory to Program Change Table
289
Appendix C: MIDI
Scene Memory to Program Change Table
Program
Change #
Initial
Scene #
1
User
Scene #
Program
Change #
Initial
Scene #
01
44
2
02
3
03
4
User
Scene #
Initial
Scene #
44
87
87
45
45
88
88
46
46
89
89
04
47
47
90
90
5
05
48
48
91
91
6
06
49
49
92
92
7
07
50
50
93
93
8
08
51
51
94
94
9
09
52
52
95
95
10
10
53
53
96
96
11
11
54
54
97
97
12
12
55
55
98
98
13
13
56
56
99
99
14
14
57
57
100
00
15
15
58
58
101
—
16
16
59
59
102
—
17
17
60
60
103
—
18
18
61
61
104
—
19
19
62
62
105
—
20
20
63
63
106
—
21
21
64
64
107
—
22
22
65
65
108
—
23
23
66
66
109
—
24
24
67
67
110
—
25
25
68
68
111
—
26
26
69
69
112
—
27
27
70
70
113
—
28
28
71
71
114
—
29
29
72
72
115
—
30
30
73
73
116
—
31
31
74
74
117
—
32
32
75
75
118
—
33
33
76
76
119
—
34
34
77
77
120
—
35
35
78
78
121
—
36
36
79
79
122
—
37
37
80
80
123
—
38
38
81
81
124
—
39
39
82
82
125
—
40
40
83
83
126
—
41
41
84
84
127
—
42
42
85
85
128
—
43
43
86
86
User
Scene #
Appendix
Program
Change#
01V96 Version 2—Owner’s Manual
290
Appendix C: MIDI
Initial Parameter to Control Change Table
CHANNEL1
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
High
NO ASSIGN
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
FADER H
NO ASSIGN
NO ASSIGN
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
Mid
Low
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
MASTER
STEREO
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
01V96 Version 2—Owner’s Manual
#
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
FADER L
NO ASSIGN
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
NO ASSIGN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
NO ASSIGN
Mid
Low
MASTER
STEREO
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
291
CHANNEL2
#
High
NO ASSIGN
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
FADER H
NO ASSIGN
ON
NO ASSIGN
NO ASSIGN
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
FADER L
Mid
Low
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
BUS1
BUS2
BUS3
BUS4
BUS5
BUS6
BUS7
BUS8
AUX1
AUX2
AUX3
AUX4
AUX5
AUX6
AUX7
AUX8
MASTER
STEREO
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
BUS1
BUS2
BUS3
BUS4
BUS5
BUS6
BUS7
BUS8
AUX1
AUX2
AUX3
AUX4
AUX5
AUX6
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
FADER L
FADER L
NO ASSIGN
BALANCE
NO ASSIGN
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
PAN
ON
ON
ON
ON
ON
ON
ON
ON
NO ASSIGN
Mid
Low
MASTER
MASTER
AUX7
AUX8
MASTER
STEREO
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
BUS1
BUS2
BUS3
BUS4
BUS5
BUS6
BUS7
BUS8
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
MASTER
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
AUX1
AUX2
AUX3
AUX4
AUX5
AUX6
AUX7
AUX8
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
292
Appendix C: MIDI
CHANNEL3
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
Mid
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
01V96 Version 2—Owner’s Manual
Low
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
Mid
Low
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
293
CHANNEL4
#
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW H
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
G LOW L
Low
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
Low
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
F LOW
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
Q LOW
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
294
Appendix C: MIDI
CHANNEL5
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
Mid
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
01V96 Version 2—Owner’s Manual
Low
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
Mid
Low
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
295
CHANNEL6
#
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID H
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
G LO-MID L
Low
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
Low
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
F LO-MID
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
Q LO-MID
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
296
Appendix C: MIDI
CHANNEL7
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
Mid
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
01V96 Version 2—Owner’s Manual
Low
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
Mid
Low
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
297
CHANNEL8
#
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID H
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
G HI-MID L
Low
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
Low
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
F HI-MID
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
Q HI-MID
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
298
Appendix C: MIDI
CHANNEL9
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
Mid
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
01V96 Version 2—Owner’s Manual
Low
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
Mid
Low
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
299
CHANNEL10
#
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH H
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
G HIGH L
Low
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
Low
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
F HIGH
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
Q HIGH
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
300
Appendix C: MIDI
CHANNEL11
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
Mid
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
01V96 Version 2—Owner’s Manual
Low
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
Mid
Low
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
301
CHANNEL12
#
High
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT H
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
ATT L
Low
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
Low
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
HPF ON
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
LPF ON
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
302
Appendix C: MIDI
CHANNEL13
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
High
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
Mid
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
01V96 Version 2—Owner’s Manual
Low
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
Mid
Low
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
303
CHANNEL14
#
High
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE H
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
LFE L
Low
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
Low
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
DIV F
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1
ST-IN2
ST-IN3
ST-IN4
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
304
Appendix C: MIDI
CHANNEL15
#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
High
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
Mid
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
01V96 Version 2—Owner’s Manual
Low
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
Mid
Low
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
INPUT12
INPUT13
INPUT14
INPUT15
INPUT16
INPUT17
INPUT18
INPUT19
INPUT20
INPUT21
INPUT22
INPUT23
INPUT24
Initial Parameter to Control Change Table
305
CHANNEL16
#
High
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
LR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
FR
Low
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
#
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
High
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
SURROUND
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
NO ASSIGN
Mid
Low
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
WIDTH
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
INPUT25
INPUT26
INPUT27
INPUT28
INPUT29
INPUT30
INPUT31
INPUT32
ST-IN1L
ST-IN1R
ST-IN2L
ST-IN2R
ST-IN3L
ST-IN3R
ST-IN4L
ST-IN4R
Appendix
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
01V96 Version 2—Owner’s Manual
306
Appendix C: MIDI
MIDI Data Format
1. DATA FORMAT
The following data types of parameter change are used by the 01V96.
Type (HEX)
1.1 CHANNEL MESSAGE
Command
8n NOTE OFF
9n NOTE ON
Bn CONTROL CHANGE
Cn PROGRAM CHANGE
rx/tx
rx
rx
rx/tx
rx/tx
function
Control the internal effects
Control the internal effects
Control parameters
Switch scene memories
1.2 SYSTEM COMMON MESSAGE
Command
F1 MIDI TIME CODE QUARTER
FRAME
rx/tx
rx
function
MTC
1.3 SYSTEM REALTIME MESSAGE
Command
F8 TIMING CLOCK
FE ACTIVE SENSING
FF RESET
rx/tx
rx
rx
rx
function
MIDI clock
Check MIDI cable connections
Clear running status
1.4.1 Real Time System Exclusive
function
MMC command
MMC response
MTC full message
1.4.2.1 Bulk Dump
rx/tx
function
BULK DUMP DATA
rx/tx
‘m’
tx/rx
tx/rx
‘S’
‘L’
tx/rx
tx/rx
‘V’
‘U’
‘C’
‘P’
‘Q’
‘Y’
‘G’
‘E’
‘H’
‘R’
‘O’
‘N’
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
function
Scene Memory & Request
(compressed data)
Setup Memory & Request
User defined MIDI remote &
Request
User defined keys & Request
User assignable layer & Request
Control change table & Request
Program change table & Request
Equalizer library & Request
Compressor library & Request
Gate library & Request
Effect library & Request
Channel library & Request
Input patch library & Request
Output patch library & Request
Plug-in Effect Card Data & Request
1.4.2.2 PARAMTER CHANGE
Command
F0 43 1n 3E 0D … F7 RARAMETER
CHANGE
F0 43 3n 3E 0D … F7 PARAMETER
REQUEST
F0 43 1n 3E 7F … F7 PARAMETER
CHANGE
F0 43 3n 3E 7F … F7 PARAMETER
REQUEST
* ‘tx’ indicates that the data can be transmitted from the 01V96, and
‘rx’ indicates that the data can be received by the 01V96.
2. Format Details
2.1 NOTE OFF
(8n)
STATUS
DATA
1000nnnn 8n Note off message
0nnnnnnn nn Note number
0vvvvvvv vv Velocity(ignored)
2.2 NOTE ON
(9n)
STATUS
DATA
1001nnnn 9n Note on message
0nnnnnnn nn Note number
0vvvvvvv vv Velocity(1-127:on, 0:off)
BULK DUMP REQUEST
rx/tx
The following data types of bulk dump are used on the 01V96.
Data name
function
Edit buffer
Patch data
Setup data
Backup data
Function (recall, store, title, clear)
Function (pair, copy)
Function (effect)
Sort table
Function (attribute, link)
Key remote
Remote meter
Remote time counter
Reception
If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
1.4.2 System Exclusive Message
Command
F0 43 0n 7E … F7 BULK DUMP
DATA
F0 43 2n 7E … F7 BULK DUMP
REQUEST
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
rx
rx
tx/rx
tx/rx
rx
tx/rx
tx/rx
Reception
If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
1.4 EXCLUSIVE MESSAGE
Command
rx/tx
F0 7F dd 06 … F7 MMC
tx
COMMAND
F0 7F dd 07 … F7 MMC RESPONSE rx
F0 7F dd 01 … F7 MIDI TIME CODE rx
1 (01)
2 (02)
3 (03)
4 (04)
16 (10)
17 (11)
18 (12)
19 (13)
20 (14)
32 (20)
33 (21)
34 (22)
rx/tx
rx/tx
function
01V96-specific parameter change
rx/tx
01V96-specific parameter change
rx/tx
General purpose digital mixer
parameter change
General purpose digital mixer
parameter request
rx/tx
01V96 Version 2—Owner’s Manual
2.3 CONTROL CHANGE
(Bn)
Reception
If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.
If [TABLE] is selected, these message are received if [Control Change Rx] is ON,
and will control parameters according to the [Control assign table] settings.
The parameters that can be set are defined in the Control Change Assign Parameter List.
If [NRPN] is selected, these messages are received if [Control Change Rx] is ON
and the [Rx CH] matches, and will control the parameter that is specified by the
four messages NRPN control number (62h, 63h) and Data Entry control number (06h, 26h). Parameter settings are defined in the Control Change Assign Parameter List.
Transmission
If [TABLE] is selected, operating a parameter specified in the [Control assign table] will cause these messages to be transmitted if [Control Change Tx] is ON.
The parameters that can be specified are defined in the Control Change Assign
Parameter List.
If [NRPN] is selected, operating a specified parameter will cause data to be
transmitted on the [Tx CH] if [Control Change Tx] is ON, using the four messages NRPN control number (62h, 63h) and Data Entry control number (06h,
26h). Parameter settings are defined in the Control Change Assign Parameter
List.
This data cannot be transmitted via control change to Studio Manager since
there is no guarantee that the contents of the tables will match. (Parameter
Change messages will always be used.)
MIDI Data Format
If [TABLE] is selected
STATUS
DATA
2.8.2 BULK DUMP
1011nnnn Bn Control change
0nnnnnnn nn Control number (0-95, 102-119)
0vvvvvvv vv Control Value (0-127)
STATUS
DATA
STATUS
DATA
STATUS
DATA
1011nnnn
01100010
0vvvvvvv
1011nnnn
01100011
0vvvvvvv
1011nnnn
00000110
0vvvvvvv
1011nnnn
00100110
0vvvvvvv
Bn
62
vv
Bn
63
vv
Bn
06
vv
Bn
26
vv
Control change
For DUMP REQUEST
F0 43 2n 7E <Model ID> tt mm mm F7
NRPN LSB
LSB of parameter number
NRPN MSB
MSB of parameter number
MSB of data entry
MSB of parameter data
Control change *1
LSB of data entry
LSB of parameter data
(Cn)
Reception
If [Program Change ECHO] is ON, these messages are echoed from MIDI
OUT.
If [Program Change RX] is ON and the [Rx CH] matches, these messages will
be received. However if [OMNI] is ON, they will be received regardless of the
channel. When a message is received, a Scene Memory will be recalled according
to the settings of the [Program Change Table].
Transmission
If [Program Change TX] is ON, this message is transmitted according to the settings of the [Program Change Table] on the [Tx CH] channel when a scene
memory is recalled.
If the recalled scene has been assigned to more than one program number, the
lowest-numbered program number will be transmitted. Transmission to Studio
Manager using Program Change messages will not be performed since there is
no guarantee that the contents of the tables will match. (Parameter Changes will
always be used.)
1100nnnn Cn Program change
0nnnnnnn nn Program number (0-127)
2.5 TIMING CLOCK
(F8)
Reception
It is used to control effects. This message is transmitted 24 times per quarter
note.
STATUS
11111000 F8 Timing clock
2.6 ACTIVE SENSING
(FE)
Reception
Once this message has been received, the failure to receive any message for an
interval of 400 ms or longer will cause MIDI transmission to be initialized, such
as by clearing the Running Status.
STATUS
11111110 FE Active sensing
2.7 SYSTEM RESET
(FF)
Reception
When this message is received, MIDI communications will be cleared, e.g., by
clearing the Running Status.
STATUS
CHECK SUM
Reception
This message is received if [Bulk RX] is ON and the [Rx CH] matches the device
number included in the SUB STATUS.
When a bulk dump is received, it is immediately written into the specified
memory.
When a bulk dump request is received, a bulk dump is immediately transmitted.
Transmission
This message is transmitted on the [Tx CH] by key operations in the [MIDI]-[BULK DUMP] screen.
A bulk dump is transmitted on the [Rx CH] in response to a bulk dump request.
The data area is handled by converting seven words of 8-bit data into eight
words of 7-bit data.
Conversion from actual data into bulk data
d[0~6]: actual data
b[0~7]: bulk data
b[0] = 0;
for( I=0; I<7; I++){
if( d[I]&0x80){
b[0] |= 1<<(6-I);
}
b[I+1] = d[I]&0x7F;
}
Restoration from bulk data into actual data
d[0~6]: actual data
b[0~7]: bulk data
for( I=0; I<7; I++){
b[0] <<= 1;
d[I] = b[I+1]+(0x80&b[0]);
}
2.8.2.1 Scene memory bulk dump format (compress)
The 01V96 can transmit and receive scene memories in compressed form.
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
(F0)
(MMC)
These messages are transmitted when the Machine Control section of the 01V96
is operated. For details, refer to the MMC specification.
DATA NUMBER
DATA NAME
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01101101
0mmmmmmm
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
6D
mh
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘m’
m=0-99, 256, 8192(Scene0-99, EDIT
BUFFER, UNDO)
0mmmmmmm ml Receive is effective 1-99, 256, 8192
01V96 Version 2—Owner’s Manual
Appendix
2.8.1 MIDI MACHINE CONTROL
DATA TYPE
A unique header (Model ID) is used to determine whether the device is a 01V96.
CHECK SUM is obtained by adding the bytes that follow BYTE COUNT
(LOW) and end before CHECK SUM, taking the binary compliment of this
sum, and then setting bit 7 to 0.
CHECK SUM = (-sum)&0x7F
11111111 FF System reset
2.8 SYSTEM EXCLUSIVE MESSAGE
DATA COUNT (the number of bytes that
follow this, ending before the checksum)
Model ID
4C 4D 20 20 38 43 39 33
tt
mm mm
cs
Control change *1
2.4 PROGRAM CHANGE
Device Number
n
cc cc
Control change *1
*1) The second and subsequent STATUS need not be added during
transmission. Reception must be implemented so that reception occurs whether or not STATUS is present.
STATUS
DATA
This message sends or receives the contents of various memories stored within
the 01V96.
The basic format is as follows.
For DUMP DATA
F0 43 0n 7E cc cc <Model ID> tt mm mm [Data …] cs F7
If [NRPN] is selected
STATUS
DATA
307
308
Appendix C: MIDI
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
tt
bb
ds
:
de
ee
F7
total block number(minimum number is 0)
current block number(0-total block number)
Scene data of block[bb]
DATA NAME
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
2.8.2.2 Scene memory bulk dump request format
(compress)
The second and third bytes of the DATA NAME indicate the scene number that
is being requested. If this is 256, the data of the Edit Buffer will be bulk-dumped.
If this is 8192, the data of the Undo Buffer will be bulk-dumped.
STATUS
ID No.
SUB STATUS
FORMAT No.
DATA NAME
EOX
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01101101
0mmmmmmm
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
6D
mh
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘m’
m=0-99, 256, 8192(Scene0-99, EDIT
BUFFER, UNDO)
0mmmmmmm ml
11110111 F7 End of exclusive
2.8.2.3 Setup memory bulk dump format
Of the setup memory of the 01V96, this bulk-dumps data other than the User
Define MIDI Remote, User Defined Keys, User Assignable Layer, Control
Change Table, and Program Change Table.
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01010011
00000010
00000000
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
53
02
00
tt
bb
ds
:
de
ee
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
F0
43
2n
7E
4C
4D
20
20
38
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01001100
00000000
0bbbbbbb
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
STATUS
ID No.
SUB STATUS
FORMAT No.
‘S’
No.256 = Current
total block number(minimum number is 0)
DATA NAME
Setup data of block[bb]
EOX
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
01V96 Version 2—Owner’s Manual
‘3’
‘S’
No.256 = Current
End of exclusive
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
4C
00
bb
tt
bb
ds
:
de
ee
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘L’
b=0-3(bank no.1-4)
total block number(minimum number is 0)
current block number(0-total block number)
User define layer data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
The second and third bytes of the DATA NAME indicate the bank number.
‘3’
End of exclusive
‘9’
2.8.2.6 User Defined MIDI Remote bulk dump request
format
‘9’
ee=(Invert(‘L’+…+de)+1)&0x7F
‘C’
The second and third bytes of the DATA NAME indicate the bank number.
Be aware that the state of the transmission destination will (in some cases)
change if the same bank is being used.
‘C’
current block number(0-total block number)
43
39
33
53
02
00
F7
2.8.2.5 User Defined MIDI Remote bulk dump format
‘8’
2.8.2.4 Setup memory bulk dump request format
STATUS
ID No.
SUB STATUS
FORMAT No.
EOX
01000011
00111001
00110011
01010011
00000010
00000000
11110111
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01001100
00000000
0bbbbbbb
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
4C
00
bb
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘L’
b=0-3(bank no.1-4)
End of exclusive
2.8.2.7 User Defined Keys bulk dump format
The second and third bytes of the DATA NAME indicate the bank number.
Be aware that the state of the transmission destination will (in some cases)
change if the same bank is being used.
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
F0
43
0n
7E
ch
cl
4C
4D
20
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
MIDI Data Format
00100000
00111000
01000011
00111001
00110011
DATA NAME 01010110
00000000
0bbbbbbb
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
20
38
43
39
33
56
00
bb
tt
bb
ds
:
de
ee
F7
‘’
2.8.2.10 User Assignable Layer bulk dump request format
‘8’
The second and third bytes of the DATA NAME indicate the bank number.
‘C’
STATUS
ID No.
SUB STATUS
FORMAT No.
‘9’
‘3’
‘V’
b=0-7(bank no.A-H)
total block number(minimum number is 0)
current block number(0-total block number)
User define key data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
DATA NAME
2.8.2.8 User Defined Keys bulk dump request format
The second and third bytes of the DATA NAME indicate the bank number.
STATUS
ID No.
SUB STATUS
FORMAT No.
DATA NAME
EOX
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01010110
00000000
0bbbbbbb
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
56
00
bb
F7
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘V’
b=0-7(bank no.A-H)
End of exclusive
The second and third bytes of the DATA NAME indicate the bank number.
Be aware that the state of the transmission destination will (in some cases)
change if the same bank is being used.
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01010101
00000000
0bbbbbbb
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
55
00
bb
tt
bb
ds
:
de
ee
F7
EOX
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01010101
00000000
0bbbbbbb
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
55
00
bb
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘U’
b=0-3(bank no.1-4)
End of exclusive
System exclusive message
2.8.2.9 User Assignable Layer bulk dump format
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
309
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
2.8.2.11 Control change table bulk dump format
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01000011
00000010
00000000
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
43
02
00
tt
bb
ds
:
de
ee
F7
‘’
‘8’
‘C’
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘C’
No.256 = Current
total block number(minimum number is 0)
current block number(0-total block number)
Control change table data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
2.8.2.12 Control change table bulk dump request format
‘M’
‘’
System exclusive message
STATUS
ID No.
SUB STATUS
FORMAT No.
‘9’
‘3’
‘U’
b=0-3(bank no.1-4)
total block number(minimum number is 0)
current block number(0-total block number)
User assignable layer data of block[bb]
DATA NAME
ee=(Invert(‘L’+…+de)+1)&0x7F
EOX
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01000011
00000010
00000000
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
43
02
00
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘C’
No.256 = Current
End of exclusive
End of exclusive
Appendix
01V96 Version 2—Owner’s Manual
310
Appendix C: MIDI
2.8.2.13 Program change table bulk dump format
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01010000
00000010
00000000
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
50
02
00
tt
bb
ds
:
de
ee
F7
System exclusive message
DATA
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
CHECK SUM
EOX
DATA NAME
EOX
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01010000
00000010
00000000
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
50
02
00
F7
STATUS
ID No.
SUB STATUS
FORMAT No.
‘P’
No.256 = Current
total block number(minimum number is 0)
current block number(0-total block number)
Program change table data of block[bb]
DATA NAME
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘P’
No.256 = Current
End of exclusive
2.8.2.15 Equalizer library bulk dump format
The second and third bytes of the DATA NAME indicate the bank number.
0:Library no.1 – 199:Library no.200,
256:CH1 – 287:CH32, 288:STEREO 1L – 295:STEREO 4R, 384:BUS1 –
391:BUS8, 512:AUX1 – 519:AUX8, 768:STEREO, 8192:UNDO
256 and following are data for the corresponding channel of the edit buffer.
For reception by the 01V96, only the user area is valid. (40-199, 256-)
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01010001
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0ttttttt
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
51
mh
ml
tt
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘Q’
0-199(EQ Library no.1-200),
256-(Channel current data)
total block number(minimum number is 0)
01V96 Version 2—Owner’s Manual
current block number(0-total block number)
EQ Library data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
The second and third bytes of the DATA NAME indicate the bank number. (See
above)
EOX
STATUS
ID No.
SUB STATUS
FORMAT No.
bb
ds
:
de
ee
F7
2.8.2.16 Equalizer library bulk dump request format
‘3’
2.8.2.14 Program change table bulk dump request format
0bbbbbbb
0ddddddd
:
0ddddddd
0eeeeeee
11110111
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01010001
0mmmmmmm
0mmmmmmm
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
51
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘Q’
0-199(EQ Library no.1-200),
256-(Channel current data)
End of exclusive
2.8.2.17 Compressor library bulk dump format
The second and third bytes of the DATA NAME indicate the bank number.
0:Library no.1 – 127:Library no.128,
256:CH1 – 287:CH32, 384:BUS1 – 391:BUS8, 512:AUX1 – 519:AUX8, 768:STEREO, 8192:UNDO
256 and following are data for the corresponding channel of the edit buffer.
For reception by the 01V96, only the user area is valid. (36-127, 256-)
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01011001
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
59
mh
ml
tt
bb
ds
:
de
ee
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘Y’
0-127(COMP Library no.1-128),
256-(Channel current data)
total block number(minimum number is 0)
current block number(0-total block number)
COMP Library data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
MIDI Data Format
311
2.8.2.18 Compressor library bulk dump request format
2.8.2.21 Effect library bulk dump format
The second and third bytes of the DATA NAME indicate the bank number. (See
above)
The second and third bytes of the DATA NAME indicate the bank number.
0:Library no.1 – 127:Library no.128, 256:EFFECT1 – 259:EFFECT4, 8192:UNDO
256-259 are the data for the corresponding area of the edit buffer.
For reception by the 01V96, only the user area is valid. (xx-127, 256-259, 8192)
(xx varies with the firmware version.)
STATUS
ID No.
SUB STATUS
FORMAT No.
DATA NAME
EOX
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01011001
0mmmmmmm
0mmmmmmm
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
59
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘Y’
0-127(COMP Library no.1-128),
256-(Channel current data)
End of exclusive
2.8.2.19 Gate library bulk dump format
The second and third bytes of the DATA NAME indicate the bank number.
0:Library no.1 – 127:Library no.128, 256:CH1 – 287:CH32, 8192:UNDO
256 and following are data for the corresponding channel of the edit buffer.
For reception by the 01V96, only the user area is valid. (4-127, 256-)
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01000111
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
47
mh
ml
tt
bb
ds
:
de
ee
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01000101
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘E’
0-127(Effect Library no.1-128),
256-259(Effect1-4 current)
total block number(minimum number is 0)
current block number(0-total block number)
Effect Library data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
2.8.2.22 Effect library bulk dump request format
The second and third bytes of the DATA NAME indicate the bank number. (See
above)
STATUS
ID No.
SUB STATUS
FORMAT No.
‘G’
0-127(GATE Library no.1-128),
256-351(Channel current data)
total block number(minimum number is 0)
current block number(0-total block number)
GATE Library data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
45
mh
ml
tt
bb
ds
:
de
ee
F7
DATA NAME
End of exclusive
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01000101
0mmmmmmm
0mmmmmmm
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
45
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘E’
0-127(Effect Library no.1-128),
256-259(Effect1-4 current)
2.8.2.20 Gate library bulk dump request format
EOX
The second and third bytes of the DATA NAME indicate the bank number. (See
above)
2.8.2.23 Channel library bulk dump format
STATUS
ID No.
SUB STATUS
FORMAT No.
EOX
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
47
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘G’
0-127(GATE Library no.1-128),
256-351(Channel current data)
End of exclusive
The second and third bytes of the DATA NAME indicate the bank number.
0:Library no.0 – 128:Library no.128,
256:CH1 – 287:CH32, 288:STEREO 1L – 295:STEREO 4R, 384:BUS1 –
391:BUS8, 512:AUX1 – 519:AUX8, 768:STEREO, 8192:UNDO
256 and following are data for the corresponding channel of the edit buffer.
For reception by the 01V96, only the user area is valid. (2-128, 256-)
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
01V96 Version 2—Owner’s Manual
Appendix
DATA NAME
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01000111
0mmmmmmm
0mmmmmmm
11110111
End of exclusive
312
Appendix C: MIDI
01000011
00111001
00110011
DATA NAME 01001000
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
43
39
33
48
mh
ml
tt
bb
ds
:
de
ee
F7
‘C’
2.8.2.26 Input patch library bulk dump request format
‘9’
The second and third bytes of the DATA NAME indicate the bank number. (See
above)
‘3’
‘H’
0-128(Channel Library no.0-128),
256-(Current data)
total block number(minimum number is 0)
STATUS
ID No.
SUB STATUS
FORMAT No.
current block number(0-total block number)
Channel Library data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
2.8.2.24 Channel library bulk dump request format
The second and third bytes of the DATA NAME indicate the bank number. (See
above)
STATUS
ID No.
SUB STATUS
FORMAT No.
DATA NAME
EOX
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01001000
0mmmmmmm
0mmmmmmm
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
48
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
52
mh
ml
tt
bb
ds
:
de
ee
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘R’
0-32(Input patch Library no.0-32),
256(Current data)
End of exclusive
Universal bulk dump
2.8.2.27 Output patch library bulk dump format
‘L’
The second and third bytes of the DATA NAME indicate the bank number.
0:Library no.0 – 32:Library no.32, 256:current output patch data, 8192:UNDO
For reception by the 01V96, only the user area is valid. (1-32, 256)
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘H’
0-128(Channel Library no.0-128),
256-(Current data)
End of exclusive
The second and third bytes of the DATA NAME indicate the bank number.
0:Library no.0 – 32:Library no.32, 256:current input patch data, 8192:UNDO
For reception by the 01V96, only the user area is valid. (1-32, 256, 8192)
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01010010
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
EOX
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
52
mh
ml
F7
n=0-15 (Device number=MIDI Channel)
2.8.2.25 Input patch library bulk dump format
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
DATA NAME
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01010010
0mmmmmmm
0mmmmmmm
11110111
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01001111
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0ttttttt
0bbbbbbb
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
4F
mh
ml
tt
bb
ds
:
de
ee
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘O’
0-32(Output patch Library no.0-32),
256(Current data)
total block number(minimum number is 0)
current block number(0-total block number)
Output patch Library data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
‘8’
‘C’
2.8.2.28 Output patch library bulk dump request format
‘9’
The second and third bytes of the DATA NAME indicate the bank number. (See
above)
‘3’
‘R’
0-32(Input patch Library no.0-32),
256(Current data)
total block number(minimum number is 0)
STATUS
ID No.
SUB STATUS
FORMAT No.
current block number(0-total block number)
Input patch Library data of block[bb]
ee=(Invert(‘L’+…+de)+1)&0x7F
End of exclusive
DATA NAME
EOX
01V96 Version 2—Owner’s Manual
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01001111
0mmmmmmm
0mmmmmmm
11110111
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
4F
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
‘8’
‘C’
‘9’
‘3’
‘O’
0-32(Output patch Library no.0-32),
256(Current data)
End of exclusive
MIDI Data Format
2.8.2.29 Plug-in effect card bulk dump format
The second byte of the DATA NAME indicates the slot number.
0:SLOT 1
The data is not received if the Developer ID and Product ID are different than
the card that is installed in the slot.
The data is not transmitted if a valid plug-in effect card is not installed.
STATUS
ID No.
SUB STATUS
FORMAT No.
COUNT HIGH
COUNT LOW
11110000
01000011
0000nnnn
01111110
0ccccccc
0ccccccc
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
DATA NAME 01001110
0mmmmmmm
0mmmmmmm
BLOCK INFO. 0bbbbbbb
0bbbbbbb
0ttttttt
0ttttttt
0000iiii
0000iiii
0000jjjj
0000jjjj
DATA
0ddddddd
:
0ddddddd
CHECK SUM 0eeeeeee
EOX
11110111
F0
43
0n
7E
ch
cl
4C
4D
20
20
38
43
39
33
4E
mh
ml
bh
bl
th
tl
0i
0i
0j
0j
ds
:
de
ee
F7
System exclusive message
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
data count = ch * 128 + cl
‘L’
‘M’
DATA NAME
EOX
F0
43
2n
7E
4C
4D
20
20
38
43
39
33
4E
mh
ml
F7
2.8.3.1.1 Parameter change basic format
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
‘’
‘8’
‘C’
DATA *)
‘9’
‘3’
System exclusive message
11110000
01000011
0001nnnn
00111110
00001101
0ttttttt
0eeeeeee
F0
43
1n
3E
0D
tt
ee
0ccccccc
0ddddddd
:
11110111
cc Channel no.
dd data
:
F7 End of exclusive
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Data type
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
‘’
EOX
‘N’
m=0(SLOT 1)
current block number(0-total block number)
total block number(minimum number is 0)
Developer id (High)
Developer id (Low)
Product id (High)
Product id (Low)
Plug-in Effect card memory data of block[bb]
*) For parameters with a data size of 2 or more, data for that size will be
transmitted.
2.8.3.1.2 Parameter Change basic format (Universal
format)
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
End of exclusive
System exclusive message
11110000
01000011
0001nnnn
00111110
01111111
0ttttttt
0eeeeeee
F0
43
1n
3E
7F
tt
ee
0ccccccc
0ddddddd
:
11110111
cc Channel no.
dd data
:
F7 End of exclusive
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Data type
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
ee=(Invert(‘L’+…+de)+1)&0x7F
The second and third bytes of the DATA NAME indicate the slot number. (See
above)
11110000
01000011
0010nnnn
01111110
01001100
01001101
00100000
00100000
00111000
01000011
00111001
00110011
01001110
0mmmmmmm
0mmmmmmm
11110111
Transmission
If [Parameter change TX] is ON and you operate a parameter for which Control
Change transmission is not enabled, a parameter change will be transmitted
with [Tx CH] as the Device Number.
As a response to a Parameter Request, a parameter change will be transmitted
with [Rx CH] as the Device Number.
Manufacture’s ID number (YAMAHA)
2.8.2.30 Plug-in effect card bulk dump request format
STATUS
ID No.
SUB STATUS
FORMAT No.
313
DATA *)
EOX
*) For parameters with a data size of 2 or more, data for that size will be
transmitted.
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Universal bulk dump
‘L’
‘M’
‘’
‘’
2.8.3.1.3 Parameter request basic format
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
‘8’
‘9’
‘3’
m=0(SLOT 1)
End of exclusive
2.8.3 PARAMETER CHANGE
2.8.3.1 Basic behavior
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Data type
EOX
0ccccccc cc Channel no.
11110111 F7 End of exclusive
2.8.3.1.4 Parameter request basic format (Universal
format)
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
11110000
01000011
0011nnnn
00111110
01111111
0ttttttt
0eeeeeee
F0
43
3n
3E
7F
tt
ee
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Data type
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
EOX
0ccccccc cc Channel no.
11110111 F7 End of exclusive
01V96 Version 2—Owner’s Manual
Appendix
Reception
If [Parameter change ECHO] is ON, these messages are echoed.
If [Parameter change RX] is ON and the [Rx CH] matches the Device Number
included in the SUB STATUS, these messages are received. A specific parameter
is controlled when a Parameter Change is received. When a Parameter Request
is received, the current value of the specified parameter will be transmitted as a
Parameter Change with the Device Number set to [Rx CH].
F0
43
3n
3E
0D
tt
ee
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
‘C’
‘N’
11110000
01000011
0011nnnn
00111110
00001101
0ttttttt
0eeeeeee
314
Appendix C: MIDI
2.8.3.1.5 Parameter Address
Consult your dealer for parameter address details.
2.8.3.2 Parameter change
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
(Edit buffer)
System exclusive message
11110000
01000011
0001nnnn
00111110
01111111
00000001
0eeeeeee
F0
43
1n
3E
7F
01
ee
0ccccccc
0ddddddd
:
11110111
cc Channel no.
dd data
:
F7 End of exclusive
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Edit Buffer
2.8.3.7 Parameter request
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
DATA
EOX
2.8.3.3 Parameter request
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
11110000
01000011
0011nnnn
00111110
01111111
00000001
0eeeeeee
F0
43
3n
3E
7F
01
ee
(Edit buffer)
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
0ccccccc cc Channel no.
11110111 F7 End of exclusive
EOX
(Patch data)
System exclusive message
0ccccccc
0ddddddd
:
11110111
cc Channel no.
dd data
:
F7 End of exclusive
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Patch data
EOX
2.8.3.5 Parameter request
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
11110000
01000011
0011nnnn
00111110
00001101
00000010
0eeeeeee
F0
43
3n
3E
0D
02
ee
(Patch data)
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Patch data
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
EOX
0ccccccc cc Channel no.
11110111 F7 End of exclusive
2.8.3.6 Parameter change
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
11110000
01000011
0001nnnn
00111110
00001101
00000011
0eeeeeee
F0
43
1n
3E
0D
03
ee
(Setup memory)
System exclusive message
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
EOX
Setup data
0ccccccc cc Channel no.
11110111 F7 End of exclusive
(Backup memory)
System exclusive message
11110000
01000011
0001nnnn
00111110
00001101
00000100
0eeeeeee
F0
43
1n
3E
0D
04
ee
0ccccccc
0ddddddd
:
11110111
cc Channel no.
dd data
:
F7 End of exclusive
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Backup data
11110000
01000011
0011nnnn
00111110
00001101
00000100
0eeeeeee
F0
43
3n
3E
0D
04
ee
(Backup memory)
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Backup data
0ccccccc cc Channel no.
11110111 F7 End of exclusive
Transmission
If [Parameter change Tx] is ON, and you store or recall a memory/library for
which Program Change transmission is not valid, this message will be transmitted with the Device Number set to the [Tx CH].
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
Setup data
01V96 Version 2—Owner’s Manual
01V96
Reception
When this is received, the specified memory/library will be stored/recalled. If
this is received from Studio Manager or Cascade Link, the operation will be executed, and then the result of execution will be transmitted as a Parameter Response.
MODEL ID (digital mixer)
0ccccccc cc Channel no.
0ddddddd dd data
MODEL ID (digital mixer)
2.8.3.10 Parameter change (Function call: Library store /
recall)
n=0-15 (Device number=MIDI Channel)
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
n=0-15 (Device number=MIDI Channel)
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
Manufacture’s ID number (YAMAHA)
01V96
Manufacture’s ID number (YAMAHA)
2.8.3.9 Parameter request
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
DATA
(Setup memory)
System exclusive message
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
F0
43
1n
3E
0D
02
ee
F0
43
3n
3E
0D
03
ee
2.8.3.8 Parameter change
Edit Buffer
11110000
01000011
0001nnnn
00111110
00001101
00000010
0eeeeeee
11110000
01000011
0011nnnn
00111110
00001101
00000011
0eeeeeee
Element no.
(If ‘ee’ is 0, ‘ee’ is expanded to two bytes)
0ppppppp pp Parameter no.
Universal
2.8.3.4 Parameter change
:
:
11110111 F7 End of exclusive
EOX
11110000
01000011
0001nnnn
00111110
01111111
00010000
00ffffff
0mmmmmmm
0mmmmmmm
0ccccccc
0ccccccc
11110111
F0
43
1n
3E
7F
10
ff
mh
ml
ch
cl
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Function call
function
number High
number Low
channel High
channel Low
End of exclusive
MIDI Data Format
function
SCENE RECALL
EQ LIB RECALL
GATE LIB RECALL
COMP LIB RECALL
EFF LIB RECALL
CHANNEL LIB RECALL
INPATCH LIB RECALL
OUTPATCH LIB RECALL
0x00
0x01
0x02
0x03
0x04
0x06
0x07
0x08
number
0-99, 8192
1-200, 8192
1-128, 8192
1-128, 8192
1-128, 8192
0-128, 8192
0-32, 8192
0-32, 8192
channel*1)
256
0-513
0-95
0-513
0-3
0-513
256
256
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
SCENE STORE
EQ LIB STORE
GATE LIB STORE
COMP LIB STORE
EFF LIB STORE
CHANNEL LIB STORE
INPATCH LIB STORE
OUTPATCH LIB STORE
0x20
0x21
0x22
0x23
0x24
0x26
0x27
0x28
1-99
41-200
5-128
37-128
xx(*2)-128
1-128
1-32
1-32
256, 16383
0-513, 16383
0-31, 16383
0-513, 16383
0-3, 16383
0-513, 16383
256, 16383
256, 16383
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
tx/rx
*1) 0:CH1 – 31:CH32, 32:ST-IN1L - 39:ST-IN4R, 128:BUS1 – 135:BUS8,
256:AUX1 – 263:AUX8, 512:STEREO
Use 256 if the recall destination or store source is a single data item.
Effect is 0:Effect 1–3:Effect 4
If the store destination is 16383 (0x3FFF), this indicates that the library data has been changed by a external cause (such as bulk reception)
(only transmitted by the 01V96)
*2) Varies with the firmware version.
2.8.3.11 Parameter change
(Function call: title)
Reception
When this is received, the title of the specified memory/library will be changed.
If this is received from Studio Manager or Cascade Link, the operation will be
executed, and then the result of execution will be transmitted as a parameter response.
Transmission
In response to a request, this is transmitted with the device number set to the
[Tx CH].
When the title is changed on the 01V96, this message will be transmitted with
the device number set to [Tx CH].
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
EOX
11110000
01000011
0001nnnn
00111110
01111111
00010000
0100ffff
0mmmmmmm
0mmmmmmm
0ddddddd
:
0ddddddd
11110111
function
SCENE LIB TITLE
EQ LIB TITLE
GATE LIB TITLE
COMP LIB TITLE
EFF LIB TITLE
CHANNEL LIB TITLE
INPATCH LIB TITLE
OUTPATCH LIB TITLE
F0
43
1n
3E
7F
10
4f
mh
ml
dd
:
dd
F7
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Function call
title
number High
title 1
:
title x(depend on the library)
End of exclusive
size
16
16
16
16
16
16
16
16
(Function call: title)
11110000
01000011
0011nnnn
00111110
01111111
F0
43
3n
3E
7F
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
title
number High
number Low
End of exclusive
Reception
When this is received, the specified memory/library will be cleared. If this is received from Studio Manager or Cascade Link, the operation will be executed,
and then the result of execution will be transmitted as a parameter response.
Transmission
When a memory or library is cleared on the 01V96, this message will be transmitted with the device number set to [Tx CH].
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
11110000
01000011
0001nnnn
00111110
01111111
00010000
0110ffff
0mmmmmmm
0mmmmmmm
11110111
function
SCENE LIB CLEAR
EQ LIB CLEAR
GATE LIB CLEAR
COMP LIB CLEAR
EFF LIB CLEAR
CHANNEL LIB CLEAR
INPATCH LIB CLEAR
OUTPATCH LIB CLEAR
F0
43
1n
3E
7F
10
6f
mh
ml
F7
0x60
0x61
0x62
0x63
0x64
0x66
0x67
0x68
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Function call
clear function
number High
number Low
End of exclusive
number
1-99
41-200
5-128
37-128
xx-128 (*1)
1-128
1-32
1-32
*1) Varies with the firmware version.
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS. This is echoed if [Parameter
change ECHO] is ON.
When this is received, the attribute of the specified memory/library will be
changed.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
EOX
11110000
01000011
0001nnnn
00111110
01111111
00010100
0000ffff
0mmmmmmm
0mmmmmmm
0ttttttt
0ttttttt
11110111
function
SCENE LIB ATTRIBUTE
F0
43
1n
3E
7F
14
0f
mh
ml
tt
tt
F7
0x00
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Function call
attribute
number High
number Low
attribute(protect:0x0001, normal:0x0000)
End of exclusive
number
0-99(0:response only)
2.8.3.15 Parameter request (Function call: attribute)
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS. This is echoed if [Parameter
change ECHO] is ON.
When this is received, a Parameter Change message will be transmitted on the
[Rx CH].
01V96 Version 2—Owner’s Manual
Appendix
Reception
When this is received, a parameter change will be transmitted with the device
number set to [Rx CH].
Refer to the above table for the Functions and Numbers.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
Function call
2.8.3.13 Parameter change (Function call: Scene/Library
Clear)
*1) Varies with the firmware version.
2.8.3.12 Parameter request
10
4f
mh
ml
F7
Transmission
In response to a request, a Parameter Change message will be transmitted on the
[Rx CH].
If [Parameter change ECHO] is ON, this message will be retransmitted without
change.
number Low
number
0-99,256(0:response only)
1-200(1-40:response only)
1-128(1-4:response only)
1-128(1-36:response only)
1-128(1-xx(*1):response only)
0-128(0:response only)
0-32(0:response only)
0-32(0:response only)
EOX
00010000
0100ffff
0mmmmmmm
0mmmmmmm
11110111
2.8.3.14 Parameter change (Function call: attribute)
System exclusive message
0x40
0x41
0x42
0x43
0x44
0x46
0x47
0x48
ADDRESS
315
316
Appendix C: MIDI
Refer to the above table for the Functions and Numbers.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
11110000
01000011
0011nnnn
00111110
01111111
00010100
0000ffff
0mmmmmmm
0mmmmmmm
11110111
F0
43
3n
3E
7F
14
0f
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
DATA
Universal
Function call
EOX
attribute
number High
number Low
End of exclusive
2.8.3.16 Parameter change
(Function call: link)
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS. This is echoed if [Parameter
change ECHO] is ON.
When this is received, the patch link data of the specified scene will be modified.
Transmission
In response to a request, a Parameter Change message will be transmitted on the
[Rx CH].
If [Parameter change ECHO] is ON, this message will be retransmitted without
change.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
EOX
11110000
01000011
0001nnnn
00111110
01111111
00010100
0010ffff
0mmmmmmm
0mmmmmmm
0iiiiiii
0iiiiiii
0ooooooo
0ooooooo
11110111
F0
43
1n
3E
7F
14
2f
mh
ml
ih
il
oh
ol
F7
MODEL ID
ADDRESS
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Function call
link
number High
number Low
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
End of exclusive
(Function call: link)
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS. This is echoed if [Parameter
change ECHO] is ON.
When this is received, a Parameter Change message will be transmitted on the
[Rx CH].
Refer to the above table for the Functions and Numbers.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
11110000
01000011
0011nnnn
00111110
01111111
00010100
0010ffff
0mmmmmmm
0mmmmmmm
11110111
F0
43
3n
3E
7F
14
2f
mh
ml
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Function call
link
Source channel H
Source channel L
Destination channel H
Destination channel L
End of exclusive
channel
0x00
0x01
0x02
11110000
01000011
0001nnnn
00111110
01111111
00010010
0000ffff
00000000
0ppppppp
00000000
0eeeeeee
11110111
function
Freeze Play button
Freeze Record button
*1)
*1)
*1)
F0
43
1n
3E
7F
12
0f
00
pp
00
ee
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
Universal
Function call Effect Event
function
Release:0, Press:1
Effect number (0:Effect1 - 3:Effect4)
End of exclusive
channel
0:Effect1-3:Effect4
0:Effect1-3:Effect4
0x00
0x01
• This does not activate when the effect type is different.
2.8.3.20 Parameter change
(Sort Table)
When scene memory sort is executed on the 01V96, the memory sort table will
be transmitted to Studio Manager.
Studio Manager will sort the memories according to this data.
If Studio Manager performs a scene memory sort, it will transmit this data to
the 01V96.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
number High
number Low
function
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS.
This is echoed if [Parameter change ECHO] is ON.
When this is received, the corresponding effect’s function activates (depending
on the effect type).
DATA
2.8.3.17 Parameter request
Function call Pair
2.8.3.19 Parameter change (Function call Event: Effect )
outpatch
0x20
Universal
*1) 0:CH1 – 31:CH32, 128:BUS1 – 135:BUS8, 256:AUX1 – 263:AUX8,
512:STEREO
Effect is 0:Effect 1–3:Effect 4
• In the case of PAIR, you must specify channels for which pairing is possible.
• In the case of PAIR ON with COPY, you must specify Source Channel
as the copy source, and Destination Channel as the copy destination.
inpatch
number
0-99(0:response only)
7F
11
0f
sh
sl
dh
dl
F7
function
PAIR ON with COPY
PAIR ON with RESET BOTH
PAIR OFF
EOX
function
SCENE LIB LINK
01111111
00010001
0000ffff
0sssssss
0sssssss
0ddddddd
0ddddddd
11110111
DATA
End of exclusive
11110000
01000011
0001nnnn
00111110
00001101
00010011
0000ffff
0ddddddd
:
0ddddddd
11110111
F0
43
1n
3E
0D
13
0f
ds
:
de
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Library sort table
Library type
Data
Data
End of exclusive
2.8.3.18 Parameter change (Function call: pair, copy)
EOX
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS. This is echoed if [Parameter
change ECHO] is ON.
When this is received, pairing will be enabled/disabled for the specified channel.
8-7 conversion is performed on the data area in the same way as for bulk.
STATUS
ID No.
SUB STATUS
GROUP ID
11110000
01000011
0001nnnn
00111110
F0
43
1n
3E
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96 Version 2—Owner’s Manual
MIDI Data Format
2.8.3.21 Parameter request
(Sort Table)
When the 01V96 receives this data, it will transmit Sort Table Data.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
11110000
01000011
0011nnnn
00111110
00001101
00010011
0000ffff
11110111
F0
43
3n
3E
0D
13
0f
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Library sort table
Library type
End of exclusive
2.8.3.22 Parameter change
(Key remote)
CH] at intervals of 50 msec as a rule (although this may not be the case if the
port is being used by other communication), for a period of 10 seconds.
If Address UL= 0x7F is received, transmission of all meter data will be halted
immediately. (disable)
Transmission
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS.
This is echoed if [Parameter change ECHO] is ON.
When this is received, the same processing that is executed when the key specified by Address is pressed (released).
Transmission
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
EOX
11110000
01000011
0001nnnn
00111110
00001101
00100000
0kkkkkkk
0kkkkkkk
0kkkkkkk
0ppppppp
11110111
F0
43
1n
3E
0D
20
kk
kk
kk
pp
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Key remote
Key address H
Key address M
Key address L
Release:0, Press:1
End of exclusive
2.8.3.23 Parameter change
(Remote Meter)
When transmission is enabled by receiving a Request of Remote meter, the
specified meter information is transmitted every 50 msec for 10 seconds. When
you want to transmit meter information continuously, a Request must be transmitted continuously within every 10 seconds.
Reception
This is echoed if [Parameter change ECHO] is ON.
Transmission
When transmission has been enabled by a Request, the parameter specified by
Address will be transmitted on the [Rx CH] channel at 50 msec intervals for a
duration of 10 seconds.
Transmission will be disabled if the power is turned off and on again, or if the
PORT setting is changed.
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
EOX
11110000
01000011
0001nnnn
00111110
00001101
00100001
0mmmmmmm
0mmmmmmm
0mmmmmmm
0ddddddd
0ddddddd
:
11110111
F0
43
1n
3E
0D
21
mm
mm
mm
dd
dd
:
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Remote meter
ADDRESS UL
ADDRESS LU
EOX
11110000
01000011
0011nnnn
00111110
00001101
00100001
0mmmmmmm
0mmmmmmm
0mmmmmmm
0ccccccc
0ccccccc
11110111
F0
43
3n
3E
0D
21
mm
mm
mm
ch
cl
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Remote meter
ADDRESS UL
ADDRESS LU
ADDRESS LL
Count H
Count L
End of exclusive
2.8.3.25 Parameter change (Remote Time Counter)
When transmission is enabled by receiving a Request of Remote Time Counter,
the Time Counter data is transmitted every 50 msec for 10 seconds. When you
want to transmit Counter information continuously, a Request must be transmitted within every 10 seconds.
Reception
This is echoed if [Parameter change ECHO] is ON.
Transmission
When transmission is enabled by receiving a Request, the Time Counter information is transmitted on [RxCH] channel every 50 msec for 10 seconds.
Transmission will be disabled if the power is turned off and on again, or if the
PORT setting is changed.
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
DATA
EOX
11110000
01000011
0001nnnn
00111110
00001101
00100010
0000tttt
0ddddddd
0ddddddd
0ddddddd
0ddddddd
11110111
F0
43
1n
3E
0D
22
0t
dd
dd
dd
dd
F7
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Remote Time counter
0:Time code, 1:Measure.Beat.Clock
Hour / Measure H
Minute / Measure L
Second / Beat
Frame / Clock
End of exclusive
2.8.3.26 Parameter request (Remote Time Counter)
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS. This is echoed if [Parameter
change ECHO] is ON.
When this is received, the Time Counter information is transmitted on the [Rx
CH] channel every 50 msec for 10 seconds.
When the second byte of Address is received on 0x7F, data transmission will be
halted immediately. (disable)
Transmission
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.
ADDRESS LL
Data1 H
Data1 L
End of exclusive
* Meter data uses the unmodified DECAY value of the DSP. The interpretation of the data will depend on the parameter.
(Remote Meter)
Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches the
device number included in the SUB STATUS. This is echoed if [Parameter
change ECHO] is ON.
When this is received, data of the specified address is transmitted on the [Rx
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
ADDRESS
EOX
11110000
01000011
0011nnnn
00111110
00001101
00100010
0ddddddd
F0
43
3n
3E
0D
22
dd
System exclusive message
Manufacture’s ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
MODEL ID (digital mixer)
01V96
Remote Time counter
0:Transmission request,
0x7F:Transmission stop request
11110111 F7 End of exclusive
01V96 Version 2—Owner’s Manual
Appendix
2.8.3.24 Parameter request
317
318
Appendix D: Options
Appendix D: Options
Rack Mounting the 01V96 Using RK1 Rack Mount Kit
1
You can rack mount the 01V96 using an optional RK1 Rack Mount Kit.
Hold one of the brackets against one side of the 01V96 so that the bracket
ear projects to the side, and align three holes on the bracket with the holes
on the side of the 01V96, as shown in the illustration below.
2
Affix the bracket using three screws included in the RK1 package.
3
Attach the other bracket to the other side of the 01V96 in the same way.
01V96 Version 2—Owner’s Manual
Index
Index
Symbols
ø/INS/DLY | DLY 1-16 page ...............80
ø/INS/DLY | DLY 17-32 page .............80
ø/INS/DLY | Insert page ...........127, 160
ø/INS/DLY | Out Dly page .........99, 110
ø/INS/DLY | Phase page .....................79
ø/INSERT/DELAY button ..................18
+48V ON/OFF switches .....................23
Numerics
1–16/17–32 buttons ............................19
1–8 buttons ..........................................21
2TR IN connectors ........................15, 70
2TR IN DIGITAL COAXIAL .............24
2TR IN DIGITAL connector ..............71
2TRD .............................................42
2TR OUT connectors ....................15, 70
2TR OUT DIGITAL COAXIAL .........24
2TR OUT DIGITAL connector ..........71
2TRD ....................................................42
A
About the display ................................27
AC IN connector .................................25
AD input ..............................................14
AD output section ...............................23
AD15/16 selector .................................15
adat .......................................................42
ADAT I/O card ....................................72
ADAT IN/OUT connector ...........24, 71
AES/EBU I/O card ...............................71
AMP SIMULATE ..............................264
Analog inputs & outputs ....................69
Assigne
Control changes ..........................220
MIDI messages ...........................209
Program changes ........................219
Remote Layer ..............................189
USER DEFINED KEYS ..............197
Attenuator ............................. 83, 99, 110
Output signals .............................106
Auto Channel Select preference .......231
Auto Direct Out On preference .......232
Auto EQUALIZER Display preference
................................................231
AUTO PAN .......................................263
Auto PAN Display preference ..........231
Auto SOLO Display preference ........231
Auto update function ........................169
Auto WORD CLOCK Display
preference .............................231
AUX 1–AUX 8 buttons .......................17
Aux outs .............................................109
Aux send mode ..........................114, 118
Aux sends ...........................................113
Attenuating .................................110
Comp settings .............................111
Copying channel fader positions
........................................120
Delaying ...................................... 110
EQ settings ..........................111, 113
Fixed mode ................................. 114
Panning ....................................... 119
Setting from the control surface
........................................ 113
Setting from the display .....110, 113
Setting levels ............................... 113
Variable mode ............................ 115
Viewing settings ......................... 112
Viewing settings for multiple
channels ......................... 117
Aux1 | View1-16 page ....................... 117
Aux1 | View17-STI page ................... 117
AUX1–AUX8 button indicators ........ 33
B
Balancing ........................................... 104
Battery ................................................ 242
Bulk dump ......................................... 226
Messages ...................................... 215
Bus out ................................................. 97
Attenuating ................................... 99
Compressing ............................... 100
Delaying ........................................ 99
EQ’ing ......................................... 100
EQ’ing and Balancing ................ 104
Naming ....................................... 107
Pairing ......................................... 105
Routing signals to the stereo bus
........................................ 101
Setting from the control surface
........................................ 104
Setting from the display ............... 99
Setting the levels ......................... 104
Viewing the settings ................... 102
BUS1–BUS8 ....................................... 139
Buttons ................................................. 29
C
Cascade COMM Link preference .... 232
Cascading consoles ........................... 238
Cascade page ............................... 240
SYNC parameter ........................ 241
CATEGORY ........................................ 73
CH1–4 ON/OFF switch ...................... 23
CH5–8 ON/OFF switch ...................... 23
CH9–12 ON/OFF switch .................... 23
Changing names ................................ 229
Channel Copy Parameter preference
............................................... 232
Channel faders ..................................... 16
Channel ID/Channel preference ...... 232
Channel library ................................. 177
Channel strip section .......................... 16
CHORUS ........................................... 262
CLEAR button ..................................... 22
Compressor library ........................... 184
Preset ........................................... 185
Compressors ........................82, 100, 111
Compressor link ......................... 149
Linking ........................................ 154
parameter table ........................... 284
319
Confirmation messages .......................30
Connections .........................................37
Configuring a recording system that
uses a DAW .....................39
Configuring a recording system with
a hard disk recorder ........38
Configuring an analog 24-channel
mixing system ..................37
Contrast control ...................................19
Control changes ........................ 215, 220
Control surface ....................................13
AD input section ...........................14
Channel strip section ....................16
Data entry section .........................22
DISPLAY ACCESS section ...........18
Display section ..............................19
FADER MODE section ................17
LAYER section ..............................19
Monitor out & Headphones section
..........................................15
SCENE MEMORY section ...........21
SELECTED CHANNEL section ..20
SOLO section ................................22
ST IN section .................................17
STEREO section ............................16
USER DEFINED KEYS section ...21
COPY ....................................................74
Cursor buttons .....................................22
D
Daisy chain distribution ......................40
Data entry section ................................22
DAW ...................................................206
Nuendo/Cubase SX ....................206
Other ............................................206
Pro tools .......................................190
Recording system ..........................39
Remote .........................................189
DEC & INC buttons ............................22
DEL button ..........................................30
Delay ...................................... 80, 99, 110
DELAY SCALE ..............................80
FB.GAIN ........................................80
DELAY LCR .......................................261
DELAY SCALE .....................................80
DELAY+ER. .......................................267
DELAY+REV .....................................268
DELAY->ER. ......................................267
DELAY->REV ....................................268
Digital I/O section ...............................24
Digital inputs & outputs .....................71
Dimensions ........................................288
DIO Warning preference ..................231
DIO/Setup | Cascade page ................241
DIO/Setup | Format page ............. 74, 75
DIO/Setup | Insert page ....................193
DIO/Setup | Machine page ...............213
DIO/Setup | Meter page ....................195
DIO/Setup | MIDI/Host page
.......................192, 212, 216, 241
DIO/Setup | Monitor page ................132
DIO/Setup | Output Att page ...........106
DIO/Setup | Prefer1 page ..................230
01V96 Version 2—Owner’s Manual
320
Index
DIO/Setup | Prefer2 page ................. 230
DIO/Setup | Remote page 192, 208, 233
DIO/Setup | Surr Bus page ............... 139
DIO/Setup | Word Clock page ..... 41, 72
DIO/SETUP button ............................ 18
Direct outs ......................................... 125
Display ................................................. 19
DISPLAY ACCESS section ................. 18
Display Brightness preference .......... 233
Display section .................................... 19
DIST->DELAY .................................. 268
DISTORTION ................................... 264
Dithering .............................................. 74
DIV ..................................................... 143
DOUBLE CHANNEL ......................... 75
DOUBLE SPEED ................................ 75
DUAL PITCH ................................... 263
DYNA. FILTER ................................. 264
DYNA. FLANGE ............................... 264
DYNA. PHASER ............................... 265
Dynamics | Comp Edit page
.................................82, 100, 111
Dynamics | Comp Lib page .............. 184
Dynamics | Gate Edit page ................. 81
Dynamics | Gate Lib page ................. 183
DYNAMICS button ............................ 18
E
EARLY REF. ...................................... 260
ECHO ................................................ 262
EDIT indicator .................................... 27
Effect | FX1 Edit page ........................ 161
Effect | FX1 Lib page ......................... 179
Effect | FX2 Edit page ........................ 161
Effect | FX2 Lib page ......................... 179
Effect | FX3 Edit page ........................ 161
Effect | FX3 Lib page ......................... 179
Effect | FX4 Edit page ........................ 161
Effect | FX4 Lib page ......................... 179
Effect | P-In Edit page ....................... 163
EFFECT button ................................... 18
Effects
Bypass .......................................... 161
Internal effects ............................ 157
parameter tables ......................... 260
Plug-ins ....................................... 163
Effects library ..................................... 179
Preset ........................................... 181
programs ..................................... 181
EMPHASIS .......................................... 73
ENTER button .................................... 22
Enter titles
Title edit window ......................... 30
EQ ........................ 84, 100, 104, 111, 113
frequency ...................................... 84
gain ................................................ 84
Q .................................................... 84
EQ | EQ Edit page ...............84, 100, 111
EQ | EQ Library page ........................ 186
EQ | Out Att page ........................ 99, 110
EQ button ............................................ 18
EQ library .......................................... 186
Preset ........................................... 187
01V96 Version 2—Owner’s Manual
EQ link ................................................149
F
F/R .......................................................143
F1–F4 buttons ......................................19
Fader groups ............................. 149, 150
FADER MODE section .......................17
Fading .................................................170
ALL CLEAR .................................170
AUX1–8 .......................................171
BUS1–8 ........................................171
Global fade time ..........................170
INPUT CH1–32 ..........................170
ST IN 1–4 .....................................170
STEREO .......................................171
FAST ...................................................142
Fast Meter Fall Time preference .......231
FB.GAIN ...............................................80
Features .................................................11
Channel configuration .................12
Effects .............................................12
Hardware .......................................11
Inputs and Outputs ......................11
MIDI ..............................................12
Remote control .............................12
Scene memory ...............................12
Sonic specifications .......................11
Surround sound ............................12
Fixed mode ................................ 114, 118
FLANGE .............................................262
FREQUENCY control .........................20
FS ...........................................................73
G
GAIN controls ......................... 15, 20, 70
Gain of the AD card .............................37
GANG ...................................................85
Gate library .........................................183
GATE REVERB ..................................260
Gates .....................................................81
KEYIN SOURCE ..........................81
parameter table ...........................284
Global Paste ........................................173
Group .................................................149
Fader groups ................................150
Mute groups ................................150
H
Hard disk
Recording system ..........................38
HIGH button .......................................20
Higher sampling rates .........................75
HIGH-MID button .............................20
HOME button ............................... 17, 34
HOME button indicator .....................33
HORIZONTAL ....................................93
HQ. PITCH ........................................263
I
I/O card ................................................71
Installing ........................................26
IEEE1394 ..............................................72
INDIVIDUAL ......................................85
INIT ....................................................139
Initial Data Nominal preference ......232
Initial Track Recording .......................49
Initializing the 01V96 ........................243
Input channels .....................................77
Attenuating ...................................83
Compressing .................................82
Delaying .........................................80
EQ ..................................................91
EQ’ing ............................................84
Gating ............................................81
Levels .............................................90
Naming ..........................................94
Pairing ...........................................92
Panning ...................................85, 90
Routing ..........................................86
Setting from the control surface ..90
Setting from the display ...............79
Switching the signal phase ...........79
Viewing the settings ......................87
INPUT connectors ........................14, 69
Input patch ........................................121
Initial settings ..............................251
Parameters ...................................249
Input patch library ............................178
Input section ........................................69
Input sensitivity
GAIN controls ..............................15
INS button ...........................................30
INSERT I/O connectors ................14, 69
Insert in ..............................................129
Insert patching ...................................127
Installing a card ...................................26
INT 44.1k, INT 48k, INT 88.2, INT 96k
.................................................42
Internal effects
Aux sends ....................................158
Editing .........................................161
Effects processors 1–4 ................157
Inserting into channels ...............160
Meters ..........................................162
MIX BALANCE ..........................161
TEMPO .......................................162
Internet, yamaha web site ...................72
INV GANG ..........................................85
K
KEYIN SOURCE .................................81
L
LAST SOLO .......................................132
LATCH ...............................................211
LAYER section .....................................19
Layers ....................................................31
Initial bank settings ....................256
LEARN button ...................................210
Level controls .......................................17
Levels ..........................................104, 113
LFE ......................................................143
Libraries ..............................................175
Channel library ...........................177
Compressor library .....................184
Index
Effects library ..............................179
EQ library ....................................186
Gate library .................................183
General operation .......................175
Input patch library .....................178
Output patch library ..................179
specifications ...............................285
Link .....................................................149
Compressors ...............................154
EQ ................................................154
LOW button ........................................20
LOW-MID button ..............................20
M
M.BAND DYNA. ..............................269
Machine control ................................212
MASTER button ..................................19
MASTER MODE .................................36
Meter | CH1-32 page ...........................34
Meter | Effect page ...............................35
Meter | Master page .............................35
Meter | Position page ..........................34
Meter | ST IN page ..............................35
Meter | Stereo page ..............................36
Metering ...............................................34
Meters
Stereo meters ................................19
MIDI ...........................................191, 215
Bulk dump ..................................226
Bulk dump messages ..................215
Control changes ..........................220
Data format .................................306
FADER H/L .................................224
Initial parameter to control change
table ................................290
MIDI IN/THRU/OUT ports 25, 215
MIDI indicator .............................27
MIDI note on/off ........................215
Parameter changes ......................225
Parameters ..................................221
Program changes ........................219
Scene memory to program change
table ................................289
Setup ............................................216
SLOT ...........................................216
System exclusive messages .........215
Transmission and Reception .....218
USB port ......................................215
MIDI | Bulk page ...............................226
MIDI | Ctl Asgn page ........................220
MIDI | Pgm Asgn page ......................219
MIDI | Setup page .............................218
MIDI button ........................................18
MIDI IN/THRU/OUT ports ..............25
MIDI interface ...................................191
MIDI machine control ......................215
MIDI remote .....................................207
Banks ...........................................207
LATCH ........................................211
LEARN button ............................210
MIDI messages ...........................209
TARGET parameter ...................208
UNLATCH ..................................211
MIDI Warning preference ............... 231
MIDI/Control Section ........................ 25
mini-YGDAI I/O cards ....................... 71
MIX SOLO ........................................ 132
MIXDOWN ....................................... 132
Mixdown ............................................. 47
mLAN I/O card ................................... 72
MMC ..........................................212, 215
MOD. DELAY ................................... 261
MOD. FILTER .................................. 264
MONITOR LEVEL control ................ 15
Monitor out & Headphones section
................................................ 15
MONITOR OUT connectors ...... 23, 70
Monitor Source selector ..................... 15
Monitoring ........................................ 131
Digital input channel status ........ 73
LAST SOLO ................................ 132
MIX SOLO .................................. 132
MIXDOWN ................................ 132
MONO ........................................ 133
RECORDING ............................. 132
Solo function .............................. 134
Solo safe function ....................... 133
Solo setup .................................... 132
MONO ............................................... 133
MONO DELAY ................................. 260
MULTI FILTER ................................ 268
Multitrack recording .......................... 47
Mute groups ..............................149, 150
Muting ............................................... 200
N
Naming ........................................ 94, 107
Nominal Pan preference ................... 231
Nuendo .............................................. 189
Nuendo/Cubase SX .......................... 206
O
OMNI OUT connectors .........24, 44, 70
OMS ................................................... 191
ON buttons .................................... 16, 17
Operating basics .................................. 27
About the display ......................... 27
AUX1–AUX8 button indicators . 33
Buttons .......................................... 29
Channel name .............................. 28
Confirmation messages ............... 30
HOME button indicator .............. 33
Metering ........................................ 34
Page area ....................................... 28
Page tabs ....................................... 28
Page title ........................................ 28
Parameter boxes ........................... 29
Rotary controls & faders .............. 29
Sampling rate indicator ............... 28
Selecting channels ........................ 32
Selecting display pages ................. 28
Selecting fader modes .................. 33
Selecting layers .............................. 31
Tab scroll arrows .......................... 28
Title edit window ......................... 30
OPERATION LOCK ........................ 237
321
Operation lock ...................................237
Optional card .......................................26
Installing ........................................26
Options .......................................... 6, 318
I/O card ..........................................71
RK1 ..............................................318
Oscillator ............................................234
Other functions ..................................229
Preferences ..................................230
Output patch ......................................123
Initial settings ..............................255
Parameters ...................................253
Output patch library ..........................179
Output section .....................................70
P
Package contents ....................................6
PAD switches ................................ 15, 69
Pair Confirmation preference ...........231
PAIR/GROUP button .........................18
Pair/Grup | In Comp page ................155
Pair/Grup | In EQ page .....................154
Pair/Grup | In Fader page .................150
Pair/Grup | In Mute page ..................150
Pair/Grup | Input page ........................93
Pair/Grup | Out Comp page .............155
Pair/Grup | Out EQ page ..................154
Pair/Grup | Out Fader page ..............150
Pair/Grup | Out Mute page ...............150
Pair/Grup | Output page ...................105
Pairing ......................................... 92, 105
HORIZONTAL .............................93
Using the display ...........................93
Using the SEL buttons ..................92
VERTICAL ....................................93
PAN control .........................................20
Pan/Route | Bus To St page ...............101
Pan/Route | Ch Edit page ..................142
Pan/Route | Pan page ..........................90
Pan/Route | ROUT1-16 page ..............86
Pan/Route | ROUT17-ST1 page .........86
Pan/Route | Surr ST IN page ............146
Pan/Route | Surr1-16 page ................146
Pan/Route | Surr17-32 page ..............146
PAN/ROUTING button .....................18
Pan/Surr | Surr Mode page ...............136
PAN/SURR LINK ..............................137
Panning ....................................... 85, 119
F.S .................................................105
FOLLOW PAN .............................89
GANG ............................................85
INDIVIDUAL ...............................85
INV GANG ....................................85
PAN buttons ..................................86
Parameter boxes ...................................29
Parameter changes .............................225
Parameter lists ....................................247
Parameter wheel ..................................22
Patch | 2TR Out page ........................125
Patch | Cascade In page .....................240
Patch | Direct Out page .....................125
Patch | Effect page ....................... 66, 158
Patch | IN LIB page ............................178
01V96 Version 2—Owner’s Manual
322
Index
Patch | IN Name page ......................... 94
Patch | In Name page ........................ 229
Patch | In Patch page .................. 43, 122
Patch | Insert In page ........................ 129
Patch | Out LIB page ......................... 179
Patch | Out Name page .............107, 230
Patch | Out Patch page .......44, 124, 239
PATCH button ............................ 18, 122
Patch Confirmation preference ....... 231
Patching ............................................. 121
2TR digital outputs .................... 125
ADAT OUT connector .............. 124
Direct outs .................................. 125
Input and Output ......................... 43
Input channels .............................. 43
Input patching ....................121, 122
Insert in ....................................... 129
Insert patching ............................ 127
OMNI OUT connector .............. 124
Omni outs ..................................... 44
Output patching ......................... 123
PATCH button ............................. 43
PEAK indicators ............................ 15, 70
Peak level ............................................. 36
PHANTOM +48V .............................. 23
Phantom Power .................................. 69
CH1–4 ON/OFF switch ............... 23
CH5–8 ON/OFF switch ............... 23
CH9–12 ON/OFF switch ............. 23
Phase .................................................... 79
PHASER ............................................. 263
PHONES jack .............................. 15, 131
PHONES LEVEL control ................... 15
PLUG-IN ........................................... 227
Plug-ins .............................................. 202
Y56K ............................................ 163
POWER ON/OFF switch ................... 25
Power section ...................................... 25
Prefer1 page ....................................... 230
Prefer2 page ....................................... 232
Preferences ......................................... 230
Pro tools .............................189, 190, 200
Automation ................................ 205
Channel display mode ............... 195
Channel levels ............................. 199
Control surface operation ......... 196
Explicit mute .............................. 200
Flip mode .................................... 201
Implicit mute .............................. 200
Insert display mode .................... 193
Meter display mode ................... 195
MIDI ........................................... 191
Muting ........................................ 201
OMS ............................................ 191
Panning ...............................200, 201
Plug-ins ....................................... 202
Pre or Post .................................. 200
Scrub & Shuttle .......................... 204
Selecting ...................................... 199
Send levels ................................... 201
Soloing ........................................ 200
Program changes .......................215, 219
PROTECT button ............................. 168
01V96 Version 2—Owner’s Manual
Q
Q control ..............................................20
Q, EQ ....................................................84
R
Rear Panel
PHANTOM +48V ........................23
Rear panel .............................................23
AD output section ........................23
Digital I/O section .........................24
MIDI/Control Section ..................25
Power section ................................25
SLOT section .................................25
RECALL button ...................................21
Recall Confirmation preference .......231
Recall safe function ............................172
RECORDING ....................................132
Remote ................................................189
FRAMES ......................................214
Insert display mode ....................193
LOCATE/TIME section .............213
Machine control ................. 189, 212
MACHINE CONTROL section
........................................213
MIDI messages ............................209
MIDI remote ...............................207
Nuendo ........................................189
ProTools ......................................189
REMOTE .....................................189
Target parameter ........................192
TRACK ARMING section ..........213
TRANSPORT section .................214
REMOTE button ........................ 19, 189
Remote Layer
Nuendo/Cubase SX ....................206
Pro tools .......................................190
RESET BOTH ......................................93
REV+CHORUS .................................265
REV+FLANGE ..................................265
REV+SYMPHO. ................................266
REV->CHORUS ................................265
REV->FLANGE .................................266
REV->PAN ........................................266
REV->SYMPHO. ..............................266
REVERB HALL ..................................260
REVERB PLATE ................................260
REVERB ROOM ................................260
REVERB STAGE ................................260
REVERSE GATE ................................260
RING MOD. ......................................264
RK1 rack mount kit ...........................318
ROTARY ............................................264
Rotary controls & faders .....................29
Routing .................................................86
Routing ST Pair Link preference ......232
S
Sampling rates ............................... 72, 73
DOUBLE CHANNEL ...................75
DOUBLE SPEED ..........................75
Sampling rate indicator ................28
Setting the higher sampling rates
..........................................75
SINGLE .........................................76
SRC sections ..................................72
Scene | In Fade page ..........................170
Scene | Out Fade page .......................171
Scene | Rcl Safe page ..........................172
Scene | Scene page .............................168
Scene | Sort page ................................173
SCENE button .....................................18
Scene MEM Auto Update preference
................................................232
Scene memories .................................165
Auto update function .................169
Edit indicators .............................166
Fading ..........................................170
PROTECT button ......................168
Recall safe function .....................172
Scene numbers ............................166
Shadow memory .........................169
Sorting .........................................173
Storing & Recalling .....................167
Using the Scene Memory Page ..168
What is stored .............................165
Scene memory #00 ............................166
Scene memory #Ud ...........................166
SCENE MEMORY section .................21
Scene numbers ...................................166
Scene up/down buttons ......................21
SEL buttons ....................................16, 17
SELECTED CHANNEL section .........20
Selecting channels ................................32
Selecting display pages ........................28
Selecting fader modes ..........................33
Setting levels .......................................113
Setup .....................................................37
Shadow memory ...............................169
SHIFT LOCK button ..........................30
SIGNAL indicators ........................15, 70
SINGLE ................................................76
SLOT ............................... 25, 42, 71, 216
SLOT section .......................................25
Solo .....................................................132
LAST SOLO ................................132
LISTEN ........................................132
MIX SOLO ..................................132
MIXDOWN ................................132
RECORDING .............................132
SOLO ...........................................132
Solo function ...............................134
SOLO SAFE CHANNEL ............133
Solo safe function .......................133
SOLO TRIM ...............................133
SOLO buttons ................................16, 17
SOLO indicator ...................................22
SOLO section .......................................22
Specifications .....................................280
SRC sections ........................................72
ST IN button ........................................17
ST IN section .......................................17
Star distribution ...................................40
STEREO DELAY ...............................261
STEREO fader ......................................16
Index
Stereo meters .......................................19
Stereo out .............................................97
Attenuating ...................................99
Compressing ...............................100
Delaying ........................................99
EQ’ing ..........................................100
EQ’ing and Balancing .................104
Naming ........................................107
Pairing .........................................105
Setting from the control surface
........................................104
Setting from the display ...............99
Setting the levels .........................104
Viewing the settings ...................102
STEREO OUT connectors ............24, 70
STEREO section ..................................16
STORE button .....................................21
Store Confirmation preference ........231
Storing and Recalling ........................167
Surround ............................................135
BUS1–BUS8 ................................139
DIV ..............................................143
F.S ................................................105
F/R ...............................................143
FAST ............................................142
INIT .............................................139
LFE ...............................................143
LINK ............................................143
Pan graph ....................................142
PAN/SURR LINK .......................137
Panning .......................................142
PATTERN ...................................143
Setting up and Selecting .............136
ST LINK ......................................143
SURROUND MODE ...........87, 137
Surround mode indicator ............27
Trajectory patterns .....................142
SURROUND MODE ........................137
Surround mode indicator ...................27
Surround modes ........................135, 136
Factory-default ...........................136
SYMPHONIC ....................................262
SYNC parameter ...............................241
System exclusive messages ................215
System version ...................................242
T
Tab scroll arrows .................................28
Tab scroll buttons ................................20
Target parameter ...............................192
Tascam I/O card ..................................72
Title edit window .................................30
TO HOST USB port ............................25
Trajectory patterns ............................143
TREMOLO ........................................263
Tutorial ................................................47
Compressing .................................57
EQ’ing ............................................56
Initial Track Recording ................49
Internal Effects ..............................66
Master Recorder ...........................68
Mixdown .......................................63
Monitoring Level ....................54, 61
323
Overdubbing ................................ 60
Pairing ........................................... 50
Recording ................................ 59, 62
Routing ......................................... 51
Setting the Input Levels ............... 49
U
UNLATCH ........................................ 211
USB ...................................................... 25
OMS ............................................ 191
USB port ..................................... 215
User assignable layer ......................... 233
USER DEFINED KEYS ...................... 21
Initial assignments ..................... 249
User defined keys .............................. 235
Utility | Battery page ......................... 242
Utility | CH Status page ...................... 73
Utility | Lock page ............................. 237
Utility | Oscillator page ..................... 234
Utility | User Def page ...................... 235
UTILITY button .................................. 18
V
Variable mode ...........................115, 118
VERTICAL .......................................... 93
View | Fader page ................88, 102, 112
View | Library page ........................... 177
View | Parameter page ........87, 102, 112
VIEW button ....................................... 18
W
WC IN .................................................. 42
Web site ............................................... 72
Website .................................................. 6
Welcome .............................................. 11
Window
Changing the surround mode ... 138
Channel Pairing ............................ 92
Copy operation ........................... 120
Password ..................................... 237
Set Password ............................... 238
User Define Select ...................... 236
WORD CLOCK IN connector .......... 24
WORD CLOCK OUT connector ...... 24
Wordclock ........................................... 40
About wordclock .......................... 40
Connections .................................. 40
Daisy chain distribution .............. 40
Source ............................................ 42
Specifying source .......................... 41
Star distribution ........................... 40
WC IN ........................................... 42
Y
Y56K ................................................... 163
Yamaha web site .................................. 72
Yamaha website ..................................... 6
01V96 Version 2—Owner’s Manual
YAMAHA [Digital Mixing Console-Internal Parameters]
Model: 01V96
Function...
Date: 26 Aug. 2002
MIDI Implementation Chart
Version: 1.0
Transmitted
Recognized
Remarks
1–16
1–16
1–16
1–16
Memorized
Memorized
Basic
Channel
Default
Changed
Mode
Default
Messages
Altered
X
X
**************
OMNI off/OMNI on
X
X
Note
Number
True Voice
X
**************
0–127
X
Velocity
Note On
Note Off
X
X
O
O
After
Key’s
Ch’s
X
X
X
X
X
X
O
O
Assignable
0–127
**************
0–127
0–99
Assignable
O
O
*1
Pitch Bend
Control
Change
Prog
Change
0-95,102-119
:True#
System Exclusive
System
Common
:Song Pos
:Song Sel
:Tune
X
X
X
X
X
X
System
Real Time
:Clock
:Commands
X
X
O
X
Aux
Messages
:Local ON/OFF
:All Notes OFF
:Active Sense
:Reset
X
X
X
X
X
X
O
O
Effect Control
Effect Control
Notes
MTC quarter frame message is recognized.
*1: Bulk Dump/Request, Parameter Change/Request, and MMC.
For MIDI Remote, ALL messages can be transmitted.
Mode 1: OMNI ON, POLY
Mode 3: OMNI OFF, POLY
Mode 2: OMNI ON, MONO
Mode 4: OMNI OFF, MONO
O: Yes
X: No
01V96 Block Diagram
01V96 Level Diagram
Analog
Analog
Digital
PAD
dBu
dBFS
Bit
+24
+20
0
0
1
2
3
4
5
6
+10
+4
0
–2
–10
–20
–30
–10
–40
–20
–30
–50
–60
–40
–70
–50
–60
–80
–90
–70
–80
–100
–110
–90
–120
–100
–110
–130
–140
–120
–130
–140
–150
–160
–170
–150
–180
–160
–170
–190
–200
–180
–210
–190
GAIN
INSERT
Digital
AD
INPUT
PATCH
PHASE
Digital
GATE INSERT
ATT.
EQ
INSERT
COMP
DELAY
ON
LEVEL
INSERT
PAN
BUS
Adder
INSERT
ATT.
EQ
INSERT
COMP
MASTER
ON
MASTER
LEVEL
INSERT
BAL
DELAY OUTPUT
PATCH
Analog
DA
dBu
Max.
Input [+24dBu]
CASCADE IN
CASCADE OUT
Digital Clipping Level
Max. Output
[+24dBu]
[+18dBu]
Nominal Output
[+4dBu]
[+4dBu]
Nominal
Input
[-2dBu]
STEREO OUT
OMNI OUT
MONITOR OUT
GAIN MIN.,
PAD ON
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Analog
+24
+20
+10
+4
0
–10
–20
–30
Max.
Input
[-40dBu]
–40
–50
Nominal
[-60dBu]
Input
–60
GAIN MAX.,
PAD OFF
–70
–80
–90
–100
–110
24
25
26
–120
27
28
29
–140
–130
–150
30
31
32
33
34
35
36
[0dBu = 0.775Vrms]
[0dBFS = Full Scale]
–160
DSP Noise Floor
–170
–180
–190
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.
ASIA
POLAND
Yamaha Music Europe GmbH
Branch Sp.z o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-868-07-57
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: 011-3704-1377
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A.
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
Yamaha Música Ibérica, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
SWEDEN
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Olga Cossettini 1553, Piso 4 Norte
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
EUROPE
THE UNITED KINGDOM
Yamaha Music U.K. Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1, N-1345 Østerås, Norway
Tel: 67 16 77 70
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
AUSTRIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
INDIA
Yamaha Music India Pvt. Ltd.
5F Ambience Corporate Tower Ambience Mall Complex
Ambience Island, NH-8, Gurgaon-122001, Haryana, India
Tel: 0124-466-5551
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
SINGAPORE
Yamaha Music (Asia) Pte., Ltd.
#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: 6747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
RUSSIA
Yamaha Music (Russia)
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
SPAIN/PORTUGAL
BRAZIL
THE PEOPLE’S REPUBLIC OF CHINA
AFRICA
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
Siam Music Yamaha Co., Ltd.
4, 6, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
OTHER ASIAN COUNTRIES
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
HEAD OFFICE Yamaha Corporation, Pro Audio Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2441
PA27
Yamaha Pro Audio Global Web Site
http://www.yamahaproaudio.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
U.R.G., Pro Audio Division
© 2006-2010 Yamaha Corporation
010IPTO-F0
Printed in Japan
WE05050
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement