Automatic Technololgy | GDO-9v2 Enduro Gen 2 | Installation manual | Automatic Technololgy GDO-9v2 Enduro Gen 2 Installation manual

Automatic Technololgy GDO-9v2 Enduro Gen 2 Installation manual
GDO-9v2 Enduro™ Gen 2
Overhead Garage Door Opener
Featuring TrioCode™ Technology
Technical Document
Installation Manual
1.01
v
26 JULY 2012
English
Part # 13289 (Manual)
INSTALLATION INSTRUCTIONS | OWNERS COPY
GDO-9v2GEN2 User Manual v101.indd 1
15/11/2012 10:07:35 AM
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the installation
instructions and the safety warnings may result in serious
personal injury and/or property damage. Please save these
instructions for future reference.
Automatic Technology (Australia) Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an
Automatic Technology (Australia) Pty Ltd Garage Door Opener. Automatic Technology (Australia) Pty Ltd hereby further
expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person
as a result whether directly or indirectly from failure to install the Automatic Technology (Australia) Pty Ltd Garage Door
Opener in accordance with these installation instructions.
2
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 2
15/11/2012 10:07:36 AM
GDO-9v2 Enduro™ Gen 2
Overhead Garage Door Opener
Important Safety Instructions
4
Features 6
Opener Controls
8
Kit Contents 10
Installation11
C-Rail Attachment 11
Determine Door Type
12
Mounting - Track Type Door
13
Mounting - Spring Loaded Door
14
Mounting Door Bracket & Arms
15
Wired Safety Beam Installation
23
16
Auto-Close Setup
24
16
Battery Backup Installation
25
SmartSolar™ Installation
26
Setting Speed and Limits
Setting Speed Mode
Setting Travel Limits - Control Panel 17
Setting Travel Limits - Transmitter
18
Final Setup 27
19
Courtesy Light Time
27
19
Pet Mode Door Height
27
Wall Mounted Transmitters 27
Reset to Factory Default
27
Door21
Default Settings & Specifications
28
Vacation Mode
21
Door Status Indicators
29
Auxiliary out put
21
Button Functions
29
Pet Mode
21
Troubleshooting Guide
30
Courtesy Light
22
Maintenance 31
Remotely Coding Transmitters
22
Parts List
32
Erasing Transmitter Codes
22
Important Safety Checks
34
Safety Obstruction Forces Safety Obstruction Force Test
Adjusting Safety Obstruction Forces 20
Coding Transmitters 21
Accessories23
Warranty35
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 3
3
15/11/2012 10:07:36 AM
Important Safety Instructions
WARNING: It is vital for the safety of persons to follow all
instructions. Failure to comply with the following safety
instructions may result in serious personal injury and/or
property damage.
CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a Photo Electric (PE)
Beam. In most countries PE Beams are mandatory on all garage doors fitted with automatic openers.
For a small additional outlay Automatic Technology recommends that Photo Electric Beams be
installed with the automatic opener ensuring additional safety and peace of mind.
DO NOT operate the opener unless the garage door is in full view and free from objects such
as cars and children/people. Make sure that the door has finished moving before entering or
leaving the garage.
DO NOT operate the opener when children/people are near the door. Children must
be supervised at all times when the opener is in use. Serious personal injury and/or
property damage can result from failure to follow this warning.
DO NOT allow children to operate the opener. Serious personal injury and/or
property damage can result from failure to follow this warning.
Regularly check to make sure that the Safety Obstruction Force is working
correctly, and is tested and set as per page 21 of this manual. Failure to
follow these instructions could result in serious personal injury and/or
property damage. This test must be repeated at regular intervals and the
necessary adjustments made as required.
Photo Electric beams must be installed if the closing force at the
bottom edge of the door exceeds 400N (40kg).
DO NOT disengage the door opener to manual operation with
children/people or any other objects including motor vehicles
within the doorway.
The door opener is not intended for use by young children
or infirm persons without adequate supervision. Children
should be supervised to ensure that they do not play
with the remote transmitters or the opener.
Keep hands and loose clothing clear of the door
and door opener at all times.
4
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 4
15/11/2012 10:07:36 AM
Important Safety Instructions
The unit should be installed so that it is protected from the elements. It should not be exposed to water or rain.
It is not to be immersed in water or sprayed directly by a hose or other device.
The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage
door installer prior to installation of the opener.
Frequently examine the installation, in particular cables, springs and mountings for signs of wear, damage
or imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation or an
incorrectly balanced door may cause injury. DO NOT attempt to repair the door yourself as hardware
is under extreme tension.
Remove or disengage all garage door locks and mechanisms prior to installation of the opener.
Connect the opener to a properly earthed general purpose 240V mains power outlet installed
by a qualified electrical contractor.
Disconnect the power cord from mains power before making any repairs or removing
covers. Only experienced service personnel should remove covers from the opener.
When using auto close mode, a Photo Electric beam must be fitted correctly and
tested for operation at regular intervals. Extreme caution is recommended when
using auto close mode. All safety rules must be followed.
In order for the opener to sense an object obstructing the door way, some
force must be exerted on the object. As a result the object, door and/or
person may suffer damage or injury.
If the power supply cord is damaged, it must be replaced by an
Automatic Technology service agent or suitably qualified person.
Make sure that the door is fully open before driving in or out of the
garage and fully closed before leaving the driveway.
Make sure that remote controls are kept out of reach of
children.
Install the wall switch or wall mounted transmitter in
a location where it is out of reach of children and the
garage door is visible.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 5
5
15/11/2012 10:07:36 AM
Features
Thank you for purchasing the Automatic Technology
GDO-9v2 Enduro™ Gen 2 Overhead Garage Door
Opener. Designed to suit sectional overhead and one
piece tilt up doors, the components and materials
used ensure this opener will provide years of
smart, simple and secure operation. Listed
below are some of the many features:
Operation
To open or close the door simply press a button on a TrioCode™ handheld
transmitter, a wall mounted transmitter, or optional wall switch for two seconds.
During open and close cycles the door can be stopped by pressing the button
again. The next button press will reverse the door’s direction.
TrioCode™ Code Hopping Technology
Every time a TrioCode™ transmitter is used a new security code is randomly
generated from over 4.29 billion possibilities. This greatly enhances the security
of the system and makes “code grabbing” a thing of the past.
These transmitters also overcome interference issues by simultaneously sending a
signal over three different frequencies. Even if two of the three signals are jammed,
the system will still work.
ALPS (Automatic Limits Positioning System)
ALPS does away with manual adjustment of the door’s limits position using mechanical
parts, such as cams and microswitches. During installation the hand held transmitter
can be programmed to set the door limits positions.
ISS (intelligent safety obstruction system)
While the door is performing a close cycle, should it hit an obstacle or be restricted in some
manner, it will automatically reverse. The amount of force the door should encounter before
reversing is automatically adjusted by the doors control system during the initial installation of the
automatic door opener. The door will also stop if restricted whilst opening. The Safety Obstruction
Force should be checked monthly.
Auto courtesy light
The courtesy light comes on automatically for three minutes whenever the door is activated. The light can also
be operated independently of the door by coding in a dedicated button on a transmitter.
Vacation mode
A hand held transmitter can be programmed to lock and unlock all other transmitters that have been
programmed into the openers’ memory. The vacation mode can be used when the door is left idle for long
periods of time.
6
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 6
15/11/2012 10:07:36 AM
SmartSolar™ and Battery Backup Compatibility (optional)
The opener can be fitted with a SmartSolar™ or Battery Backup kit for operation in the
event of a power outage, or where mains power access is not available.
NOTE: If the door is the only entrance to the garage, and a battery backup kit is not
fitted, a keyed cable release should be fitted externally to the garage.
Pet/Pedestrian mode
The transmitter can be programmed to open the door to an adjustable partial
height so that the family pet can enter and exit the garage at any time. You may
also wish to open the door to a height suitable only for pedestrian access.
Auto-Close mode
The opener can be programmed to automatically close after an open cycle. The
Auto-Close time is adjustable. It is compulsory to install a Photo Electric (PE) Beam
if this mode is selected, otherwise the door may cause personal injury or damage
to property.
Safety Beam (optional)
The opener has an input to connect a Safety Beam for extra safety and use of the
Auto-Close mode. Easy Beam PE 3 kit or Wireless PE Beam kit can be used with this
opener.
Safety Beam Failure Emergency Close
When a safety beam prevents movement due to any reason other than a ‘real’ obstruction, the
user can secure their property by pressing and holding a button on the remote control or OSC
on the console.
Manual operation
The opener is equipped with a unique manual disengaging device. If the power to the opener is disrupted, the
door can be put into manual mode by pulling down on the string handle on an angle towards the door. This
allows for manual operation of the door. To re-engage the opener, pull the string handle away from the door.
Service Indicator
The opener has a built in counter with a default setting of 3000 cycles. When the counter expires the opener will
beep and flash to indicate a service is required.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 7
7
15/11/2012 10:07:36 AM
Opener Controls
8
01
Terminal Block.
02
SET button (orange) is used during the installation phase together with the OPEN and MINUS (-) buttons to set
03
LIGHT CODE button (white) is used for storing or erasing the transmitter button (code) you wish to use to switch
04
CODING LED (red) light flashes when a code is being stored or when a transmitter button is pressed.
05
OPERATE button (yellow) is used during installation to test the open, stop and close cycles for the opener. The
06
DOOR CODE button (blue) is used for storing or erasing transmitter buttons for door operation
07
DOOR STATUS LED (yellow)
08
MINUS (-) button (red) is used during installation to help set the close limit position. Pressing and holding this
09
PLUS (+) button (green) is used during installation to help set the open limit position. Pressing and holding this
10
CLOSE LIMIT LED (red) the LED is very helpful during installation. It illuminates and flashes when the door is
11
OPEN LIMIT LED (green) the LED is very helpful during installation. It illuminates and flashes when the door is
12
AUTO CLOSE TIME button (white) is used to adjust the auto close time. While holding the AUTO CLOSE
13
FORCE MARGIN SET button: the obstruction force margin is set automatically during installation. The margin
V+ is used to power devices such as Wireless PE Beam, external receiver etc.
EB1 first Safety Beam input.
0V (Input) is a 0 volt connection for PE Beam, external receiver, osc, aux etc.
EB2 second Safety Beam input.
0V (Input) is a 0 volt connection for PE Beam, external receiver, osc, aux etc.
O/S/C INPUT is used for the connection of a wired switch (momentary contact). This switch can then be used to
open, stop or close the door. Install the wall switch in a location where the switch is out of reach of children and
the garage door is visible.
AUX output can be used to control another device (such as alarm system etc) via the opener’s remote control.
the door limit positions. The SET button is also used to re-initialize the opener.
the courtesy light on the opener on or off.
opener has to be initialised by the SET button to make the O/S/C button operable.
button will move the door in the close direction. Movement stops when the button is released.
NOTE: The safety obstruction detection is inoperable when the MINUS (-) button is used to move door.
button will move the door in the open direction, releasing stops the door.
NOTE: The safety obstruction detection is inoperable when the PLUS (+) button is used to move door.
closing and remains steady on when the close limit position has been reached.
opening and remains steady on when the open limit position has been reached.
TIME button and then pressing the PLUS (+) button the time is increased. Each press will increase the time by 1
second. Pressing the MINUS (-) button will decrease the time.
can be adjusted manually using the Force MARGIN SET BUTTON (white). Holding the MARGIN SET BUTTON and
pressing PLUS (+) or MINUS (-) buttons will increase or decrease the amount of force. The Force Margin Set should
only be used if environmental factors (wind, etc.) affect the door’s operation.
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 8
15/11/2012 10:07:36 AM
17
16
15
01
14
fig 01
02
03
04
05
06
07
08
09
10
11
12
13
14
PROG INPUT is used to connect the Automatic Technology Handheld Programmer ‘PG-3’ for editing control
15
JP1 CONNECTOR the shunt must be fitted for solar operation.
16
17
and receiver functions, accessing diagnostic tools, and activating special features and operating modes.
SBCO2 J4 STANDBY BATTERY OR SOLAR CHARGER CONNECTOR the shunt must be plugged
if battery or solar charger is not connected.
10A Fuse
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 9
9
15/11/2012 10:07:37 AM
Kit Contents
Drive Unit
1 x GDO-9v2 Enduro™ Gen 2 drive unit (Fig. 02)
1 x TrioCode™ Transmitter pack (Fig. 02)
(Pack includes two keyring transmitters and batteries)
1 x Wall mount transmitter with battery (Fig. 02)
2 x Door attachment arms (Fig. 02)
1 x Accessory and hardware pack (Fig. 02)
1 x Installation Manual
fig 02
PLUS
Pre-Assembled Single Piece C-Rail
fig 03
10
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 10
15/11/2012 10:07:38 AM
C-Rail Attachment
Single piece
C-Rails are pre-tensioned during manufacturing for
transport. Some extra tension may be required after
installation.
Shaft
If the C-Rail needs to be shortened or lenghtened (using
the extension kit) ensure these modifications are made
to the drive unit end.
fig 04
Locate shaft into sprocket
Step 1 - Secure C-Rail to Drive Unit
a.
Locate and insert the shaft of drive unit into the CRail’s sprocket (Fig. 04).
b. Fix the two track brackets with four screws supplied
in accessory pack (Fig. 05).
Hex flange screw taptite ‘S’ M4 x 10
Track bracket (x2)
fig 05
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 11
11
15/11/2012 10:07:39 AM
Determine the Door Type
Step 2 - Determine Door Type
Determine which type of garage door you have as
illustrated below. (Fig. 06 to Fig. 08) .
For a sectional (panel) door on tracks (Fig. 06)
proceed with the installation from Step 3.
Track
fig 06
Door
Sectional door with track
Header wall
Track
For a one-piece door on tracks (Fig. 07)
proceed with the installation from Step 3.
Door
fig 07
Highest point of travel
One piece door with
track
For a one-piece door without tracks (on springs) (Fig. 08)
proceed with the installation from Step 7.
Door
fig 08
One piece door
without track
12
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 12
15/11/2012 10:07:40 AM
Mounting on a Track Type Door
WARNING: The opener must be securely
fastened to structural supports, otherwise opener
failure may ensue causing serious personal injury
and/or property damage.
60mm
Level
60mm
Level
fig
Step 3 - Determine Bracket Position
a.
Open the door and find the highest point of travel of
the top door panel.
b. Using a level, transfer this height to the wall above
the door (Fig. 9) and mark a line 60mm above it.
c. Determine the centre point on the wall above and on
top of the door. Draw two lines extending 21.5mm
from each side of the centre point. (Fig. 10)
Track
9
Track
Door
Door
Step 4 - Mounting the Wall Bracket
a.
Centre the bracket over the intersection of these two
lines. Mark centres for at least two holes (Fig. 10)
and ensure it is into a solid mounting point.
b. Drill holes into the wall with an appropriate drill bit.
c. Secure to the wall using:
IF CONCRETE OR BRICK - 8mm (5/6”) loxins/dynabolts.
IF TIMBER - wood screw #20 or similar (min. 50mm).
3
4 .5
1
52
21.
fig 10
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
Drilled holes
Step 5 - Attach the Rail to the Wall Bracket
a.
Attach the C-Rail assembly to the wall bracket
with the 90mm long clevis pin and secure with the
supplied snap pin (Fig. 11)
b. Leave the drive unit in its packing box for protection
during installation.
fig 11
Step 6 - Secure the Drive unit to the Ceiling
a.
Raise the drive unit from the packing box and support
it in the horizontal position with a step ladder.
b. Open the garage door. Rest the opener on the open
door and use a scrap piece of wood to bring it to
horizontal level.
c. Line up the track perpendicular to the wall.
d. Secure the perforated angle (not supplied) to the
ceiling above where drive unit’s mounting holes will
be once fully installed. A representative mounting is
shown (Fig. 12)
e. Connect the drive unit to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of drive unit mounting holes.
f. To prevent moisture on the C-rail running into the
powerhead it is recommended a strip of silicon
sealant is placed across the top of the C-rail just
before the opener.
Structural member
fig 12
Go to Step 11 on page 15
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 13
13
15/11/2012 10:07:41 AM
Mounting on a Spring Loaded Door
WARNING: The opener must be securely fastened to
structural supports, otherwise opener failure may ensue
causing serious personal injury and/or property damage.
Centre of Door
Step 7 - Determine the Door’s Centre
a.
Find the centre of the door and mark this location
both above the door and on top of the door.
b. Draw two lines 21.5mm either side of this (Fig. 13).
fig 13
Step 8 - Prepositioning the Opener
a. Raise the door to open position.
b. Rest the opener on the top edge of the door with
end of the rail against the wall (Fig. 14).
c. Support the drive unit level with the lowest point of
the open door (Fig. 14).
NOTE: Do not slide rail along the face of the door.
Step 9 - Mounting the C-Rail
a.
fig 14
Step
ladder
C rail
Highest point
of door travel
fig 15
Door
Step
ladder
Close the door slowly. The rail will be elevated by
the top edge of the door as it moves.
b. Stop the door when it is at its highest point of travel.
Allow 25mm additional height for clearance between
the door and the track (Fig. 15).
c. Support the rail in this position and close the door
d. The height determined in Step 10(b) will be the
height at which to mount the wall bracket.
e. Centre the bracket along the line determined in Step
8.
f. Using the bracket as a template, mark a minimum of
two holes and drill with appropriate size bit. For a
more secure fitting, the wall bracket can be anchored
using more than two holes.
g. Secure the bracket to the wall using:
IF CONCRETE OR BRICK - 8mm (5/6”) loxins/dynabolts.
IF TIMBER - wood screw #20 or similar (min. 50mm)
h. Attach the bracket and C-Rail with supplied pins (Fig. 11).
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
Step 10 - Secure the drive unit to the Ceiling
fig 16
Ceiling
Aluminium rail
Shuttle VP2 assembly
6 mm M A X
(HEIGHT OF BOLT HEAD)
Drill hole at centre of track (recommended bolt size
M6 or M8)
a.
Secure the perforated angle (not supplied) to the
ceiling above where drive unit’s mounting holes will
be. See (Fig.18) for a representative mounting.
b. Connect the drive unit to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of drive unit’s mounting holes (Fig. 12).
c. To prevent moisture on the C-rail running into the
powerhead it is recommended a strip of silicon
sealant is placed across the top of the C-rail just
before the opener.
Step 10.1 - Alternative Mounting Option
The opener can be fastened to the roof by driving a bolt
through the C-Rail into a structural timber support. The
bolt head’s height must not exceed 6mm (Fig. 16).
14
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 14
15/11/2012 10:07:42 AM
Mounting Door Bracket & Arms
Step 11 - Mounting Door Bracket
The door bracket comes in two parts. The bottom plate
with two mounting holes is used on its own for one piece
doors. For sectional doors, the top plate is placed over
the bottom plate and is fixed with four (4) screws (Fig.
17).
fig 17
a.
Mount the door bracket, or bracket assembly,
on the door’s centre line one-third down the top
panel (Fig. 17) using M6 or equivalent screws (not
supplied),
b. STEEL DOORS ONLY: Bracket can be welded in
place.
NOTE: If in doubt about the door’s strength,
reinforcement may be added to the door’s frame
where necessary. Door damage may occur if the
bracket is installed on a panel with insufficient
strength. The opener’s warranty does not cover
damage caused to the door and/or door panels.
Arm connected to
the shuttle
fig 18
Step 12 - Attaching the Arms
FOR SECTIONAL AND ONE PIECE DOORS WITH
TRACK:
a. Assemble the bent arm (connecting to the door)
to the right side of the straight arm (connecting to
the shuttle) with bolts and nuts supplied in the accessory pack (Fig. 18). Always use both bent and
straight arms.
b. Connect the assembled arm to the bracket and
the disengaged trolley with clevis and snap pins.
The angle “A” must be more than 10° (Fig. 19).
The bent section must be closest to the door.
Arm connected to
the door
Centre of the door
0
10
A
WARNING: Connecting the bent arm the other
way around may damage the door. The straight
arm should not protrude beyond the heel of the
bent arm.
fig 19
FOR ONE PIECE DOORS WITHOUT TRACK
a. Assemble the bent and straight arms as shown
in (Fig. 20) with bolts and nuts supplied in the
accessory pack. Always use both the bent and
straight arms.
b. Connect the assembled arm to the bracket and the
disengaged trolley with clevis and snap pins. The
bent section must be closest to the C-rail.
c. If installing on a door with a bad wave action,
lengthening the arm will assist in reducing this
effect.
IMPORTANT NOTE: Adjust the length of the
cord so that its toggle is no more than 1.8m from
the ground.
Bent Arm closest
to the door
fig 20
Bent Arm closest
to the C-rail
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 15
15
15/11/2012 10:07:43 AM
Setting Speed and Limits
Step 13 - Setting Speed Mode
The default speed of the opener has been set to suit the
majority of applications. However, there are three speed
modes available if required:1.
2.
3.
fig 21
Slow - to suit one piece door without tracks
Medium ( default ) - suits majority of applications
Fast - to suit some sectional applications
The speed settings can only be changed before setting
the travel limits. If the opener speed needs to be changed
please complete the steps below. If medium (default)
mode is appropriate skip straight to step 13.1 setting travel
limits. Pressing the operate button will cycle through all
three speed modes. To change the speed setting:a.
Engage the C-Rail’s trolley (attached to the door via
the arms) with the chain index by moving the door.
b. If the trolley does not “click” firmly onto the chain
index, ensure that the manual release cord is not in
the disengaged position by pulling it backwards.
c. Turn on the power to the opener. The CLOSE LIMIT
LED will be flashing.
d. Remove the button cover with a blade screwdriver
(Fig. 21).
e. Press operate button once, twice or three times to
select slow, medium or fast speed mode.
16
Door Opener
Speed Mode
OPEN
LED
(Green)
CLOSE
LED
(Red)
Beeper
Medium ( Default )
On
On
2 beeps
Fast
On
Off
3 beeps
Slow
Off
On
1 beep
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 16
15/11/2012 10:07:43 AM
Setting Speed and Limits
Setting Travel Limits : Via Control Panel
Step 13.1 - Setting Travel Limits
NOTE: If Safety Beams are to be used they must be
installed before setting the travel limits.
WARNING! Use caution when operating the manual
release with the door open since it may fall rapidly
due to weak or broken springs, or an improperly
balanced door.
fig 22
CAUTION! Do not disengage the opener to manual
operation with children, persons or any objects
including motor vehicles within the doorway.
a.
Engage the C-Rail’s trolley (attached to the door via
the arms) with the chain index by moving the door.
b. If the trolley does not “click” firmly onto the chain
index, ensure that the manual release cord is not in
the disengaged position by pulling it backwards.
c. Turn on the power to the opener. The CLOSE LIMIT
LED will be flashing.
d. Remove the button cover with a blade screwdriver
(Fig. 22).
e. Press and hold the MINUS (-) button - the door will
start closing (Fig. 23).
f. Release the MINUS (-) button when the door is near
the desired closed position. Single presses of the
MINUS (-) button will “inch” the door closed.
g. If the door overshoots press the PLUS (+) button to
move the door in the open direction.
h. When the door is at the desired close position, press
the SET button to record the close limit position. The
OPEN LIMIT LED will now flash.
i. Press and hold the PLUS (+) button to open the door
(Fig. 24).
j. Release the PLUS (+) button when the door is near the
desired open position. Single presses of the PLUS (+)
button will “inch” the door open.
k. If the door overshoots press the MINUS (-) button to
move the door in the close direction.
fig 23
WARNING! Once the next step is performed, the
door will automatically close and open to calculate
force settings. Keep persons and objects clear of the
door until it stops and the opener sounds a beep.
i.
Press the SET button to store the open limit. Please
read the above warning.
fig 24
Step 13.2 - Resetting Travel Limits
To reset the limits, press and hold the MINUS (-) button for
6 seconds until the CLOSE LIMIT LED flashes quickly. If no
action is taken within 30 seconds, the opener will return to
normal operating mode and restore the original settings.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 17
17
15/11/2012 10:07:43 AM
Setting Speed and Limits
Setting Travel Limits : Via Transmitter
The GDO-9v2 Enduro™ Gen 2 has the alternate
ability to set travel limits using the transmitter, allowing
free movement around the garage to better assess the
desired limit positions.
Step 14.1 - Code a Transmitter for Limit Setting
a.
Ensure the opener is powered up and button cover
is removed.
b. Press and hold the DOOR CODE button (Fig. 25).
c. Press Button 1 on the transmitter for two seconds
(Fig. 26). Release and pause for two seconds.
Press the Button 1 again for two seconds.
d. Release the DOOR CODE button.
fig 25
Step 14.2 - Setting Limits via Transmitter
a.
Button 1
(Inch Open)
fig 26
Button 4
(Inch Close)
Button 2
(Set)
Engage the C-Rail’s trolley (attached to the door via
the arms) with the chain or belt index by moving the
door.
b. If the trolley does not “click” firmly onto the chain
index, pull the cord backwards until it locks in place,
and try again.
c. Press and hold Button 4 on the transmitter to close
the door. When the door is approx. 20mm from the
ground, release Button 4 (Fig. 26).
d. Each press of Button 4 will allow you to “inch” the
door closed. Keep doing this until the door reaches
the desired close limit position.
e. If the door overshoots, press Button 1 to “inch” the
door towards open
f. When in the correct close limit position, press Button
2 to store this in memory.
g. Press and hold Button 1 to open the door. When
approx. 20mm from the desired open position,
release Button 1.
h. Each press of Button 1 will allow you to “inch” the
door open. Keep doing this until the door reaches
the desired open limit position.
i. If the door overshoots, press Button 4 to “inch” the
door towards closed.
IMPORTANT
WARNING: The door will
automatically close, open and close again once the
next step is performed. Ensure that no persons or
objects are in the door’s path.
j.
k.
When in the correct open limit position, press Button
2 on the transmitter to store into memory.
The door will now automatically close, open and close
to calculate the safety obstruction settings. After
this, the opener can be operated with the OPERATE
button.
Step 14.3 - Resetting the Door Limit Positions
Limit positions can be deleted by the following steps:
a. Follow Steps 13.2, as outlined previously.
b. Repeat Steps 14.1 and 14.2 to set new travel limit
positions.
c. There is no need to re-code the transmitter (Step
14.1) upon resetting travel limits. The transmitter
will still be stored in memory.
18
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 18
15/11/2012 10:07:44 AM
Safety Obstruction Forces
Safety Obstruction Force Test
WARNING! Take care when testing or adjusting
the Safety Obstruction Force. Excessive force
may cause SERIOUS PERSONAL INJURY and/or
PROPERTY DAMAGE.
WARNING! Photo electric beams must be installed
if the closing force at the bottom edge of the door
exceeds 400N (40kg) force.
fig 27
Step 15.1 - Testing Close Cycle
Press the OPERATE button to open the door (Fig.
27).
b. Place a piece of timber approximately 40mm high
on the floor directly under the door (Fig. 34).
c. Press the OPERATE button to close door. The door
should strike the object and start to re-open.
a.
Step 15.2 - Testing Open Cycle
Press the OPERATE button to close the door (Fig.
28).
b. Press again to open the door. When the door
reaches the half open point, grab the bottom rail of
the door firmly and the door should stop.
c. If the door does not reverse readily when closing,
or stop when opening, the force may be excessive
and need adjusting, refer below.
a.
fig 28
40mm block of wood
DANGER! If the door fails these tests, put the
opener into manual mode, only operate the door
by hand and call for service.
NOTE: Once the travel limits are set and safety
obstruction force tested check the chain or belt tension.
As per the sticker on the C-rail the chain or belt should
sag slightly, so there is a 5mm gap between the bottom
of the C-rail and the chain or belt.
The tension can be varied by using a spanner to adjust
the bolt at the door end of the C-rail.
Be sure not to over-tension the chain or belt as this can
cause damage to the C-rail or opener.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 19
19
15/11/2012 10:07:44 AM
Safety Obstruction Forces
Adjusting Safety Obstruction Force
The Safety Obstruction Force is calculated automatically
during setup. Adjusting this is normally only necessitated
by environmental conditions such as windy or dusty areas,
and areas with extreme temperature changes.
WARNING! Photo electric beams must be installed
if the closing force at the bottom edge of the door
exceeds 400N (40kg) force.
fig 29
Step 16.1 - To Increase Force Pressure
a. Hold down FORCE MARGIN SET button (Fig. 29)
b. While holding the FORCE MARGIN SET button,
press the PLUS (+) button. Each press increases the
force margin (Fig. 29).
c. The OPEN LIMIT LED will flash each time the PLUS
(+) button is pressed to indicate a force increase
d. If the OPEN LIMIT LED is on continuously when
pressing the PLUS (+) button, this indicates that the
maximum setting has been reached.
e. Test the force again as per Steps 15.1 and 15.2
Step 16.2 - To Decrease Force Pressure
a. Hold down FORCE MARGIN SET button (Fig. 29)
b. While holding the FORCE MARGIN SET button,
press the MINUS (-) button. Each press decreases
the force margin (Fig. 29).
c. The CLOSE LIMIT LED will flash each time the MINUS
(-) button is pressed to indicate a force decrease.
d. If the CLOSE LIMIT LED is on continuously when
pressing the MINUS (-) button this indicates that the
maximum setting has been reached.
e. Test the force again as per Steps 15.1 and 15.2
fig 30
Step 16.3 - To Recall Factory Set Force
a.
While holding down the FORCE MARGIN SET
button, press the SET button for two (2) seconds.
(Fig. 30)
b. Release both buttons. The default setting should
now be recalled.
Step 16.4 - To Recalculate Force Margins
a.
Press and hold the SET Button for two (2) seconds,
the beeper will sound once (Fig. 31).
b. The door will start to move and re-calculate force
margins. The door can move between the open and
close limit positions up to four (4) times (depending
on the position of the door and the power up
condition).
c. A single beep will be heard once the process is
complete.
d. Test the force again as per Steps 15.1 and 15.2.
fig 31
20
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 20
15/11/2012 10:07:45 AM
Coding Transmitters
Step 17.1 - Code a Transmitter Button for
Door Operation
a. Ensure the button cover is removed
b. Press and hold the DOOR CODE button (Fig. 32).
c. Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
d. Release the DOOR CODE BUTTON.
e. Press the transmitter button to test.
fig 32
Step 17.2 - Code a Transmitter Button to
Enable Vacation mode
The opener can be programmed into a “Vacation
Mode” where the opener will not respond to any
transmitter except the button of the transmitter that was
programmed for vacation mode.
a.
Briefly press the DOOR CODE button once, then
press it again and hold (will beep two times on
second press (Fig. 33).
b. Press one of the four (4) buttons on the transmitter
for two (2) seconds, pause for two (2) seconds,
then press the same button again for two (2)
seconds.
c. Release DOOR CODE button.
d. Press and hold the transmitter button for six (6)
seconds to set Vacation Mode. The door code
LED will stay lit while Vacation Mode is active.
e. To reset Vacation Mode, press the same button
for two seconds.
Step 17.3 - Code a Transmitter Button to
Enable AUX OUTPUT
a.
Briefly press the DOOR CODE button two (2)
times, then press it again and hold (will beep
three times on third press (Fig. 34)).
b. Press one of the four buttons on the transmitter
for two (2) seconds, pause for two (2) seconds,
then press the same button again for two (2)
second.
c. Release the DOOR CODE button.
d. Press the transmitter button to test.
fig 33
fig 34
Step 17.4 - Code a Transmitter Button for Pet
(Pedestrian) Mode
a.
Briefly press the DOOR CODE button three times,
then press it again and hold (will beep four times on
fourth press (Fig. 35)).
b. Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
c. Release the DOOR CODE button.
d. Press the transmitter button to test.
To change the default pet (pedestrian) door opening
position, refer Step 24.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 21
fig 35
21
15/11/2012 10:07:46 AM
Coding Transmitters
Step 18 - Remotely Coding Transmitters
Using this method transmitters can be coded without
access to the opener’s control panel as long as a precoded transmitter is available.
IMPORTANT NOTE: The door or courtesy light
must activate when the steps below are performed.
This indicates that the pre-coded transmitter is in
range of the opener, and the correct button has
been pressed.
fig 36
a.
Take any pre-coded transmitter. Press the button
for the function to be duplicated and release.
b. Using a small needle, press and hold firmly for
two seconds through the Coding Hole (Fig. 37).
c. WITHIN 10 SECONDS take the additional
transmitter you wish to code. Decide which
button that you want to activate the function to
be duplicated (e.g. activate the door, or turn on
the courtesy light)
d. Hold the new transmitter’s button for two
seconds, pause for two seconds, hold again for
two seconds and then release.
e. Wait for 10 seconds and then press the new
transmitter’s button to test.
fig 37
Step 18.1 - Erasing a Stored Transmitter
Code
a. Select the transmitter you want to delete.
b. Press and hold the DOOR CODE BUTTON (Fig.
38).
c. Press the transmitter button you would like to
delete for two seconds, pause for two seconds,
press again for two seconds and then release.
d. Release the DOOR CODE BUTTON. The code
should now be deleted. Confirm this by pressing
the transmitter button - the function (e.g. door
opening) should not respond.
fig 38
Step 18.2 - Erasing All Transmitter Codes
Step 17.5 - Coding a Transmitter Button
to the Courtesy Light
The transmitter can be programmed to operate the
courtesy light on the opener independently of the
door moving.
a. Press and hold LIGHT CODE button (Fig.
36).
b. Press one of the four buttons on the
transmitter for two (2) seconds, pause for
two (2) seconds, then press the same button
again for two (2) seconds.
c. Release the LIGHT CODE button.
d. Press the transmitter button to test.
22
a. Turn off power to the opener.
b. While switched off, press and hold the DOOR
CODE BUTTON (Fig. 38). Turn on power to the
opener while holding this button.
c. The OPEN LIMIT, CLOSE LIMIT and DOOR
STATUS LEDs will illuminate for about five
seconds. These LED’s will turn off and the
CODING LED will illuminate.
d. Release the DOOR CODE BUTTON. All stored
codes will now be deleted. Confirm this pressing
buttons on any previously coded transmitters the opener should not respond.
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 22
15/11/2012 10:07:46 AM
Wired Safety Beams Installation
Step 19 - Safety Beams (optional)
Safety Beams extend across the garage door opening.
The Safety Beam is designed to detect an obstruction
while the door is closing and to send a signal to the
garage door opener to reverse or stop the door
movement. One or two sets of Safety Beams can be
connected to GDO-9v2 Enduro™ Gen 2 opener.
6
4
3
fig 39
Step 19.1 - Fitting the Safety Beam
a.
Attach the mounting bracket (4) to the adjustment
bracket (3) with the pan head screw (6) (supplied).
(Fig. 39)
b. Attach the bracket (2) to the Safety Beam
transmitter with four taptite screws (m3x5) and
attach the other side to the adjustment bracket (3)
with the pan head screw (6) . (Fig. 40)
c. Repeat steps a and b to assemble the Safety Beam
receiver.
2
1
6
d. Mount the receiver to one side of the door and
transmitter on the other side in line with receiver.
The mounting surface should be rigid. ATA
recommends the transmitter and receiver are
placed in line of sight, with the beam 100mm
above ground level (as per AS60335). They should
also be placed as close as possible to the door
opening. Connect as per the wiring diagram (Fig.
41).
fig 40
Step 19.2 - Alignment
a.
Power up the opener with the Safety Beam
connected. The green LED on the transmitter
should turn ON to indicate power is present.
b. If the receiver is connected to power and the
red LED is flashing while the green LED on the
transmitter is on, the transmitter and receiver are
not aligned.
c. Make horizontal and/or vertical adjustment on the
transmitter and/or receiver until the red LED on the
receiver turns on, indicating alignment.
NOTE: The sensors need to be 100mm above
the floor level, however, the exact position
must be chosen in such a manner that it suits
the application, the environmental conditions
and provides maximum safety protection.
fig 41
BLACK
WARNING: Safety Beam must be installed if
the closing force as measured at the bottom
edge of the door exceeds 400N (40kg).
BLACK
BLACK
RED
RED
RED
BLACK
NOTE: Three wire Safety Beam is not compatible with
GDO-9v2 Enduro™ Gen 2 opener.
GDO-9v2 Enduro™ Gen 2 is compatible with wireless safety beams. Please
refer to instructions provided with wireless safety beams for installation
details.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 23
23
15/11/2012 10:07:47 AM
Wired Safety Beams Installation
Step 19.2 - Safety Beam Failure Emergency Close
When the user finds that they are unable to move the door and suspect that it is due to a faulty SAFETY BEAM
they can attempt to enter Safety Beam Failure Emergency Close mode by press and holding a pre-coded
button on the remote control or OSC button on the console for five seconds.
Auto-close Setup
WARNING: It is compulsory to have Safety Beams
installed when using Auto-Close mode. When using
Auto-Close Mode and Safety Beams, the doorway
must be clear of all obstructions and persons at all
times.
Step 20 - Setting Up Auto-Close Mode
fig 42
Auto-Close mode is a function that automatically closes
the door a preset time after the PE Beams recognise that
a vehicle has left the garage.
The Auto-Close timer only starts after the PE Beam’s
path is broken the Auto-Close timer has been set. If the
PE Beam’s path is not broken the door will remain open
until the path is broken. If the opener incurs a physical
obstruction (i.e. not from the PE Beams) while closing
the door, it will re-open and not Auto-Close until the PE
Beam’s path is broken again.
Step 20.1 - Setting Auto-Close Time
a. Hold down the AUTO CLOSE TIME button.
b. While holding in the AUTO CLOSE TIME button,
press the PLUS (+) button, - each press will add
one second to the Auto-Close delay (Fig. 42).
c. To decrease the delay time follow Step 21.1(a)
and press the MINUS (-) button - each press will
deduct one second from the Auto-Close delay
(Fig. 43).
d. Press the OPERATE button or transmitter to open
the door.
e. Break the Safety Beam’s path momentarily to
initialise Auto-Close. When the door is fully
opened the OPEN LIMIT LED will flash to indicate
that Auto-Close mode is operational.
f. The door will pause for the set Auto-Close time
and then close.
fig 43
24
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 24
15/11/2012 10:07:47 AM
Battery Backup Installation
fig 44
Battery Backup Installation
Step 21.1 - Connect the Battery Back Up Kit
a. Disconnect power to the opener.
b. Remove screws and swing open the cover (Fig 44).
c. Mount the PCB support with two screws item # 13.
Secure the SBC0-2 Charger Board onto the PCB
support with three (3) screws item #14.
d. Feed the 2-wire battery harness item # 10 through
the grommet on the base plate and connect to
SBCO-2 battery charger board.
e. Feed charger harness from SBCO-2 battery charger
board to the control board and plug onto the 5 pin
connector marked “SBCO-2” on the control board.
f. Mount Battery Backup and secure with item 11 and
12.
WARNING: After Step 21.1(g) the opener may
become active (even when power is off). This is a
result of a residual charge in the batteries.
g. Connect battery harnesses item 5 and 10 together
(Fig 44).
h. Reconnect power.
Step 21.2 - Testing Battery Back Up
a.
Press either the OPERATE button or transmitter
to test the opener.
b. Whilst door is in motion, disconnect mains
power the door should continue to operate as
normal.
NOTE: Wait for the door to complete its travel.
c.
Press the OPERATE button or transmitter to
activate the door.
d. Whilst door is in motion re-connect power. The
door should complete the cycle as normal.
Step 21.3 - Troubleshooting
If door stops or moves very slowly under battery
power, the batteries may be weak or have no
charge. Connect mains power and allow the
batteries to charge. This may take 24 - 48 hours to
reach maximum charge capacity.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 25
25
15/11/2012 10:07:49 AM
SmartSolar™ Installation
WARNING: Do not connect batteries until Step
22.3
Step 22.1 - Mount the Charger Board
a. Unplug the drive unit from mains power.
b. Remove the screws, swing open the main cover and
remove the light diffuser. Then remove the transformer,
EMC board (if fitted) and mains power cable.
c. Mount the PCB support with two screws .Secure the
SOL charger board on to PCB support with 3 screws.
(Fig. 45).
d. Unplug the shunt & plug the solar charger Board’s
three wire harness (red/yellow/black) into the control
board’s “SBCO-2” connector on the control board
(Fig. 46).
e. Plug the solar shunt (supplied) onto the control
board’s “Jp1” connector marked “solar”(Fig. 46)
Fig 45
IMPORTANT WARNING: Do not connect battery
or solar panel polarity incorrectly - this will result in
serious damage to components.
Fig 46
Step 22.2 - Connect the Solar Panel
a.
Mount the solar panel as outlined in the SmartSolar™
Installation Manual.
b. Feed the Solar Panel’s cable through black grommet
located on the top of the plastic drive unit cover.
c. Connect the red wire to the Charger Board’s
“SOLAR+” connector, and the black wire to the
“–SOLAR” connector (Fig. 47).
WARNING: During Step 22.3 the opener will
become active.
Step 22.3 - Mount & Connect the Battery
Black
Yellow
ry)
a. Mount the Battery Box close to the opener.
b. Feed the 2-core 18awg gauge cable (supplied)
through the Battery Box’s grommet.
c. Connect the red wire to the Battery Box’s “+” terminal,
and the black wire to the “–” terminal (Fig. 48).
d. Feed the other end of the battery cable through the
drive unit’s black grommet.
e. Connect the red wire to the Charger Board’s
“BAT+” connector, and the black wire to the “–
BAT” connector (Fig. 47).
f. Refit the light diffuser and main cover.
Step 22.4 - Re-setup and Test the Opener
a.
Setup travel limits and code transmitters as per the
GDO-9v2 Enduro™ Gen 2 instruction manual.
b. Press either the OPERATE button or use a transmitter
to operate the opener.
Fig 48
26
Red
ttery)
ire
W
ck
ire
a
l
B
W
d
Re
Red (From Ba
tte
Black (From Ba
Red (From Solar P
anel)
olar Panel)
Black (From S
Fig 47
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 26
15/11/2012 10:07:51 AM
Final Setup
Step 23 - Setting of Courtesy Light Time
The preset courtesy light time is three minutes. This time
can only be changed by “PG3” programmer.
Step 24 - Setting the Pet Mode position
The default Pet Mode height can be changed as follows:
a. Drive and stop the door at the desired Pet Mode
open position by pressing OPERATE button on
the console or the transmitter button coded for
O/S/C operation.
b. Press and hold the OPEN button (Fig 49) for six
(6) seconds until the OPEN and CLOSE LED’s are
lit to record the new pet position.
When activated, Pet Mode drives the door to the preset
position from the close position. Pet Mode’s active status
is indicated by both the OPEN and CLOSE LIMIT LED’s
being illuminated. If a Pet Mode button is pressed while
the door is moving, the door will stop. If a Pet Mode
button is pressed when the door is in the Pet position,
then the door will close.
fig 49
fig 50
Step 25 - Installing the Wall Mounted
Transmitter (Optional)
a. Remove the faceplate from the transmitter.
b. Affix the baseplate in a convenient wall location
that is out of reach of children and convenient
to the customer (Fig 50). Make sure the door is
visible from this location.
c. Replace the faceplate.
d. To code the transmitter, see Steps 17.1 through
17.5 on page 21 and 22.
Step 26 - Reset all Factory Defaults
a. Turn power to opener off.
b. Press and hold the SET Button (Fig 51).
c. Turn power on while holding the SET button.
Continue to hold until all the LED’s are off.
d. This will not erase transmitter codes stored in
memory.
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 27
fig 51
27
15/11/2012 10:07:52 AM
Default Settings & Specifications
Factory default settings
Default
Step
Maximum
Courtesy light time
3 Mins.
4 Mins.
Obstruction force margin
0.7 Amps
0.1 Amps
2.0 Amps
Auto close time
0 Secs
1 Sec.
255 Secs.
Speed Mode
Medium
1
Fast
Maintenance counter
3000 Cycles
-
-
Technical specifications
28
Power supply
230V - 240V AC 50Hz
220V AC 60Hz Export Model
Transformer rating
24V DC
Standby power
2.2 Watts
Input power
200 Watts
Motor type
24V DC permanent magnet
Shuttle travel distance in the C-Rail
2.8m approx. (standard 3160 mm C-rail)
Maximum shuttle travel distance in the C-Rail
5m (with extended C-Rail)
Maximum door opening: Width x Height
Weight:
18m2
100 kg
Minimum Clearance
(Bottom of C-Rail to highest point of door travel)
40 mm
Rated load
500N (50kg)
Nominal force
150N (15kg)
Receiver code storage capacity
64 x 4 button transmitter codes
Transmitter frequency
TrioCode™ type
Coding type
Multi-frequency Code hopping
Number of code combinations
Over 4.29 billion random codes
Code generation
Non-linear encryption algorithm
Transmitter battery
CR 2032, 3 Volts
Courtesy light
Bright LED
Controller fuse
10A slow blow
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 28
15/11/2012 10:07:52 AM
Door Status Indicators
Door Opener State
OPEN LED
(Green)
Open
On
CLOSE LED (Red)
Close
Opening
STATUS LED
(Yellow)
Beeper
On
Flashing
Closing
Flashing
Door travel stopped
Flashing
Door obstructed when opening
Flashing
Flashing
Door obstructed when closing
Flashing
Opener overloaded
Alternating flashes
Door in open position with AutoClose mode selected
One second flashes
Pet Mode Engaged
On
Mains power interrupted
Rapid flashes
Beeps as door moves
Alternating flashes
On
Service Due
On
3 Beeps At The Start
Of Each Cycle
Button Functions
Buttons
Function
OPERATE
Change speed mode, Opens/Stops/Closes the door,
pressing & holding will close the door in the event of safety
beam failure.
DOOR CODE
Codes a transmitter button for operate, vocation, auxiliary and
pedestrian functions
LIGHT CODE
Codes a transmitter button for light function
FORCE MARGIN SET & PLUS (+)
Increases the obstruction force margin setting
FORCE MARGIN SET & MINUS (-)
Decreases the obstruction force margin setting
FORCE MARGIN SET (then) SET
Resets the factory default force margin settings
AUTO CLOSE TIME (then) PLUS (+)
Increases the auto close delay time
AUTO CLOSE TIME (then) MINUS (-)
Decreases the auto close delay time
AUTO CLOSE TIME (then) SET
Resets the factory default auto close delay time
MINUS (-) for 6 secs.
Clears the door limits set positions. Limits then need to be
reset
PLUS (+) for 6 secs.
Enters pet (pedestrian) position mode
SET (then power on) & hold until all LED’s are off
Deletes control parameters excluding transmitter storage
memory
DOOR CODE (then power on) & hold until all LED’s
are off
Deletes all transmitter storage memory
SET & DOOR CODE (the power on) and hold until all
LED’s are off
Deletes all control parameters and transmitter storage
memory.
SET
Re-initialises the Opener to re-calculate force margin
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 29
29
15/11/2012 10:07:52 AM
Troubleshooting Guide
Symptom
Possible cause
Remedy
Door will not operate
Mains power not switched on
Switch on mains power
Door is obstructed
Remove obstruction
Door is locked or motor jammed
Unlock door or remove jam
Door tracks/hardware damaged
Door requires service/repair by
qualified technician
Adverse weather conditions (wind
or cold) causing door to stiffen and
become tight in the tracks
Increase force margin setting.
See Step 16 on page 22
Possible obstruction in
the doorway
Remove obstruction
Transmitter code not stored
in memory
Code transmitter into opener’s
memory. Refer Step 17.1 on page
23
Flat battery
Replace battery
Door will not close fully
Door limits position need to
be reset
Reset limits positions. Refer Step
14.3 on page 20
Door will not open fully
Door limits position need to
be reset
Reset limits positions. Refer Step
14.3 on page 20
Courtesy light not working
Faulty light
Replace globe or LED module
Auto close not working
PE Beam or wiring faulty
Repair PE Beam or replace wiring
Door starts to close but
automatically reverses to
open position
Door operates from drive unit
(operate) button but not from
transmitter.
Re-align optics. See PE Beam’s
instructions
Opener beeps and flashes at the
end of each operation
PE Beam is obstructed
Remove obstruction from the path
of PE Beam
Door obstructed when closing
Remove obstruction
Auto-close time not set
See Step 20 on page 26
Service is due on the door and
opener
Please refer to page 30 or sticker
on the back of the door for more
information
PLEASE NOTE:
Intermittent operations may occur in areas which experience very strong winds. The strong wind puts
extra pressure on the door and tracks which may in turn trigger the safety obstruction detection system
intermittently.
Safety Beams must be installed if the closing force at the bottom edge of the door exceeds 400N (40 kg)
force
30
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 30
15/11/2012 10:07:52 AM
Maintenance
Maintenance
Maintenance counter
To ensure a long and trouble free life for your
opener, the following is recommended:
At this time Automatic Technology recommends
you contact your door professional to perform an
annual door service.
Whilst your opener does not require any periodic
maintenance, the door that it is fitted to, does.
Your garage door is a large, heavy, moving object
and should be tested regularly to ensure it is in
good condition. A poorly maintained door could
cause fatal or serious injuries or serious damage to
property.
GDO-9v2 Enduro™ Gen 2 has a built in maintenance
counter. From factory this is loaded with 3000 cycles.
When this counter expires, the service yellow LED
will light up. At the start of each door movement
the beeper will sound three times. After opening
or closing the door the courtesy light will flash and
beeper sound five times.
Monthly
•
•
When maintenance counter is active it can be
reloaded with 3000 cycles by press and holding the
SET button on the console.
Disengage the opener and manually operate
the door: The door must be smooth to operate
by hand. An operating force on the bottom rail
should not exceed 150N (15kg) force.
Each month, check that the opener reverses
when the door contacts a 40mm high object
placed on the floor (AS3350).
CAUTION: Frequently examine door,
particularly cables, springs and mountings for
signs of wear, damage or imbalance. Do not
use if repair or adjustment is needed since
a fault in the installation or an incorrectly
balanced door may cause injury. (AS3350)
NOTE: If the door does not operate smoothly, call
your installer.
Adjustments should only be carried out by
experienced persons, as this function can
be dangerous if not performed under strict
safety procedures.
WARNING! Failure to maintain your garage
door may void the warranty on your garage
door opener.
Service Record
Record any maintenance in the following table to assist in any warranty service.
Date
Service by
Signature
Invoice No.
Amount
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
GDO-9v2GEN2 User Manual v101.indd 31
31
15/11/2012 10:07:52 AM
Parts List
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 32
15/11/2012 10:07:55 AM
33
GDO-9v2GEN2 User Manual v101.indd 33
Owner Installation Instructions GDO-9v2 Enduro™ Gen 2
33
15/11/2012 10:07:58 AM
Important Safety Checks
Please refer to the risk assessment table below and ensure all the necessary controls are in place.
Installation Risk Assessment
Hazard
Control
Muscular strain from incorrect
lifting of opener
•
Practice correct lifting techniques (carton weighs 9 kg)
Muscular strain from incorrect
lifting of door
•
Practice correct lifting techniques when required to lift the door as
per installation instructions
Entanglement in operating Opener
•
Never plug in and operate prior to installation
Fall from ladder
•
•
•
Ensure ladder is the correct type for job
Ensure ladder is on flat ground
Ensure user has 3 points of contact while on ladder
Testing and Operation Risk Assessment
34
Hazard
Control
Entrapment under operating door
•
•
•
•
•
Keep children clear of operating door
Ensure the garage door is in good working order
Correctly set the Safety Obstruction Force
Install Photo Electric Beams (recommended)
Do not operate door when persons are near the door
Entanglement in moving door
•
Keep hands and loose clothing clear of door and guides at all times
Entanglement in operating Opener
•
Never plug in and operate prior to installation
Electrocution
•
•
•
•
Place opener in protected area so that it does not get wet
Do not spray with water
Do not open the protective covers
Do not operate opener if cable is damaged
GDO-9v2 Enduro™ Gen 2 Owner Installation Instructions
GDO-9v2GEN2 User Manual v101.indd 34
15/11/2012 10:07:58 AM
Warranty and Exclusion of Liability
1. This Warranty is given by Automatic Technology (Australia)
Pty Ltd (ABN 11 007 125 368) (ATA), 6-8 Fiveways Boulevard,
Keysborough 3173, 1300 133 944, sales@ata-aust.com.au
2. The Competition and Consumer Act 2010 (including the
Australian Consumer Law) and other relevant statutes provide a
set of statutory consumer guarantees and other legal rights that
cannot be excluded, restricted or modified by contract. This
Warranty is in addition to and does not affect any of your rights
under the Australian Consumer Law and other relevant statutes.
3. Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation
of any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not
amount to a major failure.
4. Subject to your non-excludable rights under the Australian
Consumer Law, ATA expressly excludes any liability for
consequential loss, incidental or indirect damages (including
but not limited to damages for loss of business profits, business
interruption and loss of business information) due to a defect of
the GDO-9v2 Enduro™ Gen 2 (Product). In particular any
loss or damage caused to other equipment or accessories used
with the product or any loss resulting from a delay in repair is
excluded to extent permitted by law.
5. Subject to all of the matters set out below, ATA warrants in
relation to the Product that:
(a) the Product’s drive units will be free of any defects in material
and workmanship for at least 24 months after the date of
purchase (as evidenced by the sales docket receipt), or 5000
cycles, which ever occurs first; and
(b)the Product’s other components and accessories will be free of
any defects in material and workmanship for at least 12 months
after the date of purchase (as evidenced by the sales docket
receipt).
6. No additional warranty will apply for Products repaired during
the relevant warranty period.
7. For all Products repaired outside the warranty period, a six (6)
month warranty that the Product will be free of any defects in
material and workmanship will apply from the date of dispatch
of the Product to you. ATA may charge you for any repairs
undertaken outside the warranty period, and will provide you
with a quotation in relation to any such costs for your approval
before proceeding with any repairs.
8. This Warranty applies only where you:
(a) immediately notify ATA at the contact details provided
in paragraph 1 above or notify the or the retailer that you
purchased the Product from of the alleged defect;
(b)return the product to the retailer that you purchased the
Product from; and
(c) present the relevant sales docket and this Warranty document
to the retailer to confirm the date of purchase.
9. Except for this Warranty, ATA gives no warranties of any kind
whatsoever (whether express or implied), in relation to the
product, and, subject to paragraph 1 above, all warranties of
whatsoever kind relating to the product are hereby excluded.
10.This Warranty excludes damage resulting from:
(a) normal wear and tear;
(b)accidental damage;
(c) incorrect installation of the Product;
(d)blown fuses, electrical surges, power surges or power spikes;
(e)theft, fire, flood, rain, water, lightning, storms or any other acts
of God;
(f) any installation, configuration or use of the Product contrary to
the instructions supplied with the Product;
(g)maximum continuous operating time exceeding 1 minute in 10;
(h)the operating force exceeding 15kg* (150 Newton) when moving
the door manually to the open or closed position;
(i) the door surface area exceeding 18m2 for GDO-9v2 Enduro™
Gen 2
(j) the door used with the Product not being in safe working order and
condition;
(k) repairs which are not authorised by ATA;
(l) any failure to install or maintain the Product in accordance with the
instructions supplied with the Product;
(m)any use which is not in accordance with the instructions provided
with the Product;
(n)deliberate or negligent damage to the Product;
(o)any unauthorised modification to the Product;
(p)faulty or unsuitable wiring in the building in which the Product is
installed;
(q)damage caused by insects;
(r) any cost or expense relating to the recall of the Product;
(s) installation of a residential garage door opener in a commercial
or industrial premises or in a dwelling other than a single-family
dwelling;
(t) radio or electrical interference; or
(u)acts or omissions of any person (including service providers
approved by ATA) other than ATA.
11.ATA’s liability under this Warranty is limited, at ATA’s absolute
option, to replacing or repairing the product which ATA, in its
unfettered opinion, considers to be defective either in material
and/or workmanship or to credit the dealer with the price at which
the product was purchased by the dealer.
12.This Warranty does not extend to cover labour for installation of the
Product following repairs, the cost of which must be borne by you.
13.This Warranty is limited to Return-to-Base (RTB) repair and does
not cover labour for on-site attendance, the cost of which must be
borne by you.
14.Except as specified in this Warranty, ATA will not charge you for any
repairs or replacements conducted under the Warranty. However,
ATA will charge you for any repairs which are not within the scope
of this Warranty (or which are not required to be undertaken free of
charge pursuant to the Australian Consumer Law).
15.This Warranty is void if the Product is not returned to the
manufacturer in original or suitably secure packaging.
16.This Warranty is only applicable for repairs to the product carried
out within Australia.
17.This Warranty does not cover consumable items including, without
limitation, globes, batteries and fuses.
18.This Warranty is not transferable.
19.Where the Product is retailed by any person other than ATA, except
for the warranty set out above, such person has no authority from
ATA to give any warranty or guarantee on ATA’s behalf in addition
to the warranty set out above.
20.Any provision of this Warranty that is prohibited or unenforceable
in any jurisdiction is ineffective as to that jurisdiction to the extent
of the prohibition or unenforceability. That does not invalidate
the remaining provisions of this Warranty nor affect the validity or
enforceability of that provision in any other jurisdiction.
21.Products presented for repair may be replaced by refurbished
goods of the same type rather than being repaired. Refurbished
parts may be used to repair the Product.
NOTES:
1. One (1) cycle = one (1) open and one (1) close action of the door.
2. This Warranty is to be read in conjunction with the owner’s copy of
the installation instruction manual.
3. * The door that the Product is used with should be balanced in such
a way that the user is able to open or close the door manually using
a force not greater than 150 Newton (15 kg), other than to initially
cause the door to start moving, which may require force in excess of
that specified in this paragraph.
35
GDO-9v2GEN2 User Manual v101.indd 35
15/11/2012 10:07:58 AM
© July 2012 Automatic Technology (Australia) Pty Ltd. All rights reserved. TrioCode™ is a trademarks of Automatic Technology
(Australia) Pty Ltd. No part of this document may be reproduced without prior permission. In an ongoing commitment to
product quality we reserve the right to change specification without notice. E&OE.
Automatic Technololgy (Australia) Pty Ltd
ABN 11 007 125 368
6-8 Fiveways Boulevard
Keysborough, Victoria, 3173, Australia
P 1300 133 944
+61 2 9722 5666 (International Enquiries Only)
E sales@ata-aust.com.au
www.automatictechnology.com.au
GARAGE DOOR OPENERS | GATE OPENERS | REMOTE CONTROL ACCESS SOLUTIONS
GDO-9v2GEN2 User Manual v101.indd 36
15/11/2012 10:07:59 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising