Vista | Quantum Plus | User manual | Vista Quantum Plus User manual

Vista Quantum Plus User manual
Quantum PLUS – Installation and User manual
User and programming manual for
Vista‟s Quantum Plus range of
DVR.
Including:
QPLUS04-XXX
QPLUS08-XXX
QPLUS16-XXX
Quantum Plus installation and user manual
This page is intentionally left blank
2
Quantum Plus installation and user manual
CE INFORMATION
The product must be installed according to the currently valid installation regulations
for EMC to guarantee the designed use and to prevent EMC problems.
The device supplied with this manual is according to the EC, EMC Directive,
89/336/EEC & LVD 73/23/EEC
Standard used for showing compliance with the essential requirements of the device:
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 50130-4
EN 55024
LVD: EN60950-1
ELECTRICAL SAFETY
Explanation of electrical safety symbols
3
Quantum Plus installation and user manual
Contents
SAFETY PRECAUTIONS .......................................................................................... 6
CONTENTS OF PACKAGING ................................................................................... 7
FEATURES ................................................................................................................ 8
FEATURES ................................................................................................................ 8
FRONT PANEL .......................................................................................................... 9
REAR PANEL CONNECTIONS ............................................................................... 12
SYSTEM CONNECTION DIAGRAM ........................................................................ 13
REMOTE CONTROL ............................................................................................... 14
OSD DESCRIPTION ................................................................................................ 15
MENU TREE ............................................................................................................ 16
DEFAULT PASSWORDS ......................................................................................... 18
MENU NAVIGATION ................................................................................................ 19
MENU SETTINGS .................................................................................................... 21
1 .DISPLAY ......................................................................................................... 21
2. RECORDING .................................................................................................. 24
3. SYSTEM ......................................................................................................... 31
Disk Format ........................................................................................................ 34
Password Change .............................................................................................. 35
CLIENT ACCOUNT ............................................................................................ 35
Program Update ................................................................................................. 36
SENSOR ............................................................................................................ 37
PTZ Setup .......................................................................................................... 38
PTZ Controller .................................................................................................... 38
Telemetry connections and User Instructions ..................................................... 39
NETWORK ......................................................................................................... 44
5. Event .............................................................................................................. 47
SEARCHING VIDEO FOOTAGE ........................................................................ 51
Archiving Evidence to DVD/CD or USB .............................................................. 54
LOG .................................................................................................................... 56
CLIENT VIEWER SOFTWARE – QT PLAYER ........................................................ 57
LOG IN ............................................................................................................... 58
Explanation of Screen Buttons ........................................................................... 58
Live Monitoring ................................................................................................... 59
Remote search ................................................................................................... 62
Remote Log ........................................................................................................ 67
Info ..................................................................................................................... 67
Remote Setup: Checking settings menu (Same as DVR) .................................. 68
Recording ........................................................................................................... 71
System................................................................................................................ 78
4
Quantum Plus installation and user manual
EVENT................................................................................................................ 85
Local Search....................................................................................................... 87
Local Setup......................................................................................................... 90
PAN, TILT, Zoom, Focus ..................................................................................... 92
Firmware Upgrade .............................................................................................. 94
Quit (Stop Client program) .................................................................................. 94
APPENDIX 1 ............................................................................................................ 95
APPENDIX 2 ............................................................................................................ 98
APPENDIX 3 .......................................................................................................... 102
APPENDIX 4 .......................................................................................................... 105
APPENDIX 5 .......................................................................................................... 107
APPENDIX 6 ........................................................................................................... 114
5
Quantum Plus installation and user manual
SAFETY PRECAUTIONS
CAUTION BEFORE USE
Please read this manual before installing or using the Vista Quantum DVR.
Please keep this manual in a safe place, to allow for future reference
For the safety and proper use, The DVR is marked with various symbols. Please read these
to prevent injury of financial loss.
INSTALLATION SITE
Ensure installation position is level, secure and adequately ventilated.
Avoid installing close to sources of humidity or water.
6
Quantum Plus installation and user manual
CONTENTS OF PACKAGING
User Manual
Power
Cable
Remote Controller
Installation
CD
7
Battery
Quantum Plus installation and user manual
FEATURES
● Convenience
- User-friendly GUI (Graphical User Interface)
-
Easy-to-use menu structure
-
Easy-to-use recorded data search (Time, Date, Motion, and Alarm)
- Easy-to control via Front Panel, IR remote control and USB 2.0 mouse.
● Stability
-
Auto restart after power interruption
-
DB structure offers data stabilisation and better storage utilisation
● Expandability
- Remote DVR‟s can be controlled using the supplied software client viewer.
● Technology
-Embedded LINUX OS
-Maximum record rate 400 fps
-High-resolution & high-quality MPEG-4 algorithm
-Uses watermarking & scrambling technologies,
-MPEG-4 : 1 ~ 2 Kbytes per image with resolution 360x240
● Functionality
- Variable recording function (normal, alarm, motion, schedule, audio, Time Lapse,)
- Full channel real-time monitoring
- Live monitoring, recording, playback, backup, remote access simultaneously
- Multi channel playback
- Variable events notification to e-mail, buzzer or PC Client system
8
Quantum Plus installation and user manual
FRONT PANEL
(1)LED
- REC: Recording status (When recording is on, the red light will flash)
- POWER: System Power On/Off (When power is on, the green light will be illuminated)
- NET: Network status (When network is connected, the light will lash)
- HDD: HDD status (When the system is reading or writing to the HDD, the light will flash)
(2) USB 2.0 PORT
- USB2.0 connector, for downloading to USB pens / drives (plus upgrading firmware)
(3) POWER BUTTON
- System Power On/Off
(4) NUMERIC & CHARACTER
- Input for numbers & letters within the setup menus and searches
(5) MENU
- Displays the menu on the screen
(6) SEARCH
- Entering search mode
9
Quantum Plus installation and user manual
(7) PLAY ( )
- Playback of the recorded data
- When in play mode press again to enter fast forward mode.
(8) REWIND ( )
- Reverse play of recorded data
- When in play mode press again to enter fast rewind mode.
(9) PAUSE ( ▌▌)
- To freeze picture on playback mode and live mode.
(10) STOP / EJECT ( █ )
- To stop playback and go back to live mode.
- To eject DVD-RW
(11) REC (●)
- It starts & stop manual recording, password protected.
(12) VOLUME UP & DOWN (
)
- To increase or decrease the volume.
(13) ARROW KEY
- Moves the cursor while in menu mode
(14) SELECT
- Menu selection
(15) PTZ Selection
- PTZ Channel selection
10
Quantum Plus installation and user manual
(16) Screen Split
- Selection of multi screen functions
(17) AUDIO Selection
- Switches between audio channels
(18) PAN / TILT
- To control P/T/Z, press this button to browse virtual key on screen.
(19) ZOOM
- ZOOM P/T/Z camera in and out
11
Quantum Plus installation and user manual
REAR PANEL CONNECTIONS
(1) VIDEO IN (BNC)
- 16/8/4 Camera input (1.0v p-p, 75Ω)
(2) VIDEO OUT
- 16/8/4 LOOP / SPOT / Composite / S-VIDEO / VGA
(3) LINE AUDIO INPUT
- 16/8/4 Audio input through line
(4) AUDIO OUTPUT
- 1 Audio output
(5) RS232
- 1 Serial Communication
(6) Network Port (RJ-45)
- Connecting to the Quantum DVR through Internet or LAN
(7) USB 2.0
-USB 2.0 connector for mouse control.
12
Quantum Plus installation and user manual
(8) ALARM / SENSOR
- ALARM / 16/8/4 SENSOR INPUT / 1 OUTPUT PORT
(9) CAMERA / KEYBOARD CONTROLLER
- 1 Serial Communication for Pan / Tilt Camera
- 1 Serial Communication for P/T/Z Control Keyboard
(10) AC POWER
- AC 110~240 V
ATTENTION
When the video format is changed, the system should be re-booted
SYSTEM CONNECTION DIAGRAM
13
Quantum Plus installation and user manual
REMOTE CONTROL
1. Power: Power ON/OFF
2. REC: Start & Stop Recording
3. (1 to 9) Numbers and letters
4. P/T/Z: Entering PTZ menu directly
5. OSD: On Screen Display ON/OFF
6. SEQ: Sequence operation
7. LOG: Direct access Log list
8. INFO: Direct access system Info.
9. ID: Reserved.
10.MUTE: Audio Mute
11.AUDIO: Switches through Audio
channels
12. MENU: Entering system menu
13. SEARCH: Entering search
14. ARROW & SPLIT: Left, Right, Up and
Down. Also, Screen split options
15. VOL”+,-“ : Up, down volume
16. CH “+,-“ : Up, down channel(s)
17.
18.
( ) : Play(or fast forward)
: Reverse play
19 II: Pause
20. █: Stop playback
21. Cam: Changing PTZ icon
22. P/T: Pan &Tilt
23. Z/F: Zoom/ & Focus
24. DIS: Channel Division
14
Quantum Plus installation and user manual
OSD DESCRIPTION
PTZ icon
Record Standby:
It is shown when
recording is not
activated.
The Status Bar shows HDD capacity, Network
This screen shows PTZ control of
connection, Time, etc using by icons.
camera 2. The on screen arrows
-HDD capacity
will allow control of this camera.
-Network connection
: 1.7GB is used out of 298.0GB
: It is shown that admin or
user is connected.
-Date/Time
*Others :
-Backup
-Mute
-USB Stick:
15
Quantum Plus installation and user manual
MENU TREE
Camera
Covert
Apply
Main Menu
Camera Name
Spot Setting
Display
OSD Setting
Event Clear
Apply
Watermark
Information
HDD
Overwrite
Recording
Pre
Resolution
Duration
Pre FPS
Pre Duration
Recording
Global
Post Duration
Normal
Quality
Alarm
Resolution
Motion
FPS
Schedule
Audio On/Off
Audio Event
Time Lapse
Priority
Apply
Language
System
Basic
Disk Format
Password Change
Client Account
Program Update
Auto Delete Mode
Date Format
Time/DST Set
Video Type
System ID
Sensor
Sensor
PTZ Setup
User Name
PTZ Controller
New Password
Apply
Confirm PW
16
Quantum Plus installation and user manual
Network Set
DDNS
IP SET
NTP
LIVE
Apply
Event
Notification
DDNS
User ID
User Password
Domain
Dynamic IP
IP
Gate Way
Net Mask
DNS Server
DSL ID
DSL PW
DVR Port
Web Port
E-Mail Registration
SMTP Mode
Video Loss
Alarm
E-Mail Out
Beep Out
Motion
Power Loss
Alarm Out
Apply
17
Quantum Plus installation and user manual
DEFAULT PASSWORDS
Front Panel
A Password is required if you need to: enter the menus; down power; stop recording or
changing an IP setting.
A prompt will be displayed asking for password.
The default Password is: 00000000 (8 zeros)
Viewer Software
When using the supplied Viewer software, the following password will be required.
User ID is “admin” (not case sensitive).
Password is “00000000” i.e. 8x Zero‟s
(Admin ID cannot be changed, as this is the full administrator ID)
18
Quantum Plus installation and user manual
MENU Navigation
To enter the set-up menu press the Menu button or right click with mouse on screen The
following screen will be displayed.
Enter the password (default password is 00000000 – 8 zeros).
Front Panel or IR remote control
All menus are navigated around using the left / Right / Up / Down and the Select button.
To step back through the menus press MENU button
Mouse control
Using the mouse allows the operator to enter the Menus to set up the Quantum or enter the
Search functions to play back and archive recorded data..
Right Clicking will bring up the following screen:
Left click the required icon from:
Menu, Search, Record, Power down, Play Forward, Audio Eject, Channel
Select and Multi Screen
19
Quantum Plus installation and user manual
When selecting either Menu or Search the following password screen will
appear, enter the password by clicking on the numbers.
If Menu has been selected the following screen will be displayed.
Select Sub menus by clicking on the relevant title.
Change Values/settings by either double clicking to bring up the following
keyboard:
Or to change other values simply multi click the segments, which will toggle through available
settings
20
Quantum Plus installation and user manual
MENU Settings
1 .DISPLAY
Camera Setting: Brightness, Saturation, Contrast, Hue and default
The picture displayed from each camera can be individually adjusted to balance the multi
screen view.
Use UP() / DOWN() or Numeric buttons on the front panel or left button on the Mouse to
move to next menu. To move to the submenu, use the SELECT button, or double click
mouse to bring up keyboard display
Camera Covert
Cameras can be hidden from the viewer in live or play back mode. Turn the camera on or off
using the left and right buttons around the SELECT button. Or toggle on and off with left
clicks of the mouse.
Camera Name
Each camera can be titled using the alphanumeric buttons on the front panel or the mouse.
Each title can have up to 32 characters, if there are too many characters to display in 1 line,
it will be shown as _... For example, „FIRST MEETING ROOM‟ -> „FIRST MEETIN…‟
21
Quantum Plus installation and user manual
Spot Setting
<Single Screen>
<Quad Screen>
<9 Channel Divisions>
<16 Channel Divisions>
Spot output is used to configure the second monitor output. The Spot monitor can respond to
Alarms, Motion, Audio, or can be configured for full or multi-screen sequences.
Select the Mode required then configure the duration required for the display of that mode..
OSD Setting
On Screen Display Setting: Selecting whether the time and date etc is shown on the screen
or not.
22
Quantum Plus installation and user manual
Event Clear
This is used to erase the list, in the memory, of previous events such as alarm activations.
APPLY: In order to save any modified setting value, please press “SEL” key when the
“APPLY” section is highlighted. This action can be carried out within each Sub Menu.
23
Quantum Plus installation and user manual
2. RECORDING
All recorded data is watermarked to ensure that it is not tampered with. Using the software
supplied the legitimacy of this data can be verified.
Global
Within this section:
1. Watermarking should be set to on, this allows the supplied software to verify the
downloaded information to ensure it has not been tampered with or changed.
2. Repeat recording can be set to continually overwrite or stop when the drives are full.
3. Pre Recording resolution can be set to 4CIF (D1) – 720 X 576 (giving 100fps
recording) or 2CIF -720 X 288 (200fps) or CIF - 360 X 288 (400fps).
4. Pre FPS/Pre Duration/Post Duration is recommended to set active to get data just
before event occurs.
Post Duration is selectable.
-Pre FPS: Value dependant on Pre resolution setting (up to 25 FPS)
-Pre Duration & Post Duration: 5/30/60/90/120/150/180/210/240 sec.
5.
Quality options are High, Middle or Low
These settings are applied to all channels.
24
Quantum Plus installation and user manual
Normal (TL)
This configures the continuous recording settings per channel
Record rates available:
In 360x288 modes, 25 fps is available to each channel (total 400fps).
In 720x288 mode 12.5 fps is available to each channel (Total 200fps).
In 720x576 mode 6.25 fps is available to each channel (Total 100fps).
Each channel can be individually configured for record rate and Audio on/off.
Alarm
There are 16 Alarm inputs on the rear of the Quantum these can be used to initiate the Alarm
record mode.
The Alarm recording is set up in the same way as Normal Recording.
25
Quantum Plus installation and user manual
Motion
Motion on any channel can trigger recording of that camera.
Resolution, Images Per second, Audio, and Quality can all be configured individually per
channel. As per Normal and Alarm Recording Modes.
To setup the motion detection grid per channel select the “Sel” button.
Motion Sensitivity
It consists of High, Mid or Low.
Motion Region
The following will be displayed when “Sel” is selected.
26
Quantum Plus installation and user manual
The detection area is divided into a grid of 11x8 cells. Default is all cells in active mode.
Use the Left right up down to move cursor and the Select key to toggle between active and
inactive.
The mouse can also be used to select cells and toggle them on and off.
Double clicking on one of the 4 dots in the corner of the selected cell, will toggle between all
cells being active or inactive.
Care must be taken in setting of the motion sensitivity. It is recommended that each level is
testing to find out which one suits that particular camera site. The motion detection is not
recommended for external cameras.
Schedule
The schedule allows the Quantum DVR to be set to only record at particular times of the day.
This timing setting is global for all channels. However the Resolution, Images per second and
Audio can be configured per channel.
To set the timetable select the large SET box on the right of the menu page, the following
page will appear. It allows each hour within the week to be set to be either Active (Orange) or
Inactive (Grey)
27
Quantum Plus installation and user manual
“SEL” button is used for selecting relevant time and day. Arrow Key will be used for
movement. Or toggle between on and off with the mouse.
Audio Event
16 Audio Inputs and 1 Output are available.
Recording can be triggered when Audio is
detected. As with Normal and Alarm recording the Resolution, Images per second can be set
per channel. Individual channels can be enabled or disabled and the sensitivity set to either
Low, Middle or High.
28
Quantum Plus installation and user manual
Duration
The Duration mode allows the user to set the number of days that they require to record for.
The resolution; whether cameras are active or not and whether audio is being recorded can
each be set per channel. The user then sets the number of days of recording required, then
the Quantum will automatically calculate best record rate to achieve these settings
NOTE:
If recording is in Standby mode, the following icon is displayed.
29
Quantum Plus installation and user manual
Priority
The RECORD PRIORITY allows the mixing of the various record methods to customise the
individual site requirements.
Example: A site may require Alarm recording at night, then a standard FPS recording during
the day. In this case the Schedule would be set for required FPS and resolution, and the
timetable set for this recording between 8am and 8pm each day. Schedule would be set as
1st Priority. The Alarm settings would be configured as required and this would be set as the
2nd priority.
The Quantum would then record between 8am and 8pm at the Scheduled rate, then once
beyond 8pm would look to the second priority and only record Alarm Events.
30
Quantum Plus installation and user manual
3. SYSTEM
The SYSTEM menu is where all the non-recording based settings are configured
Basic
User can set Language, Auto Delete Mode, Date Format, Time/DST Set, Video Type, System
ID. Also, Initialisation and system Information is available.
Language
The default is English.
Italian, French, Hungarian, Slovak, German, Russian, Chinese,
Dutch, Spanish, Portuguese, Japanese and Polish are available.
Auto Delete Mode
Auto Delete Mode can be set to Automatically erase recorded information over a certain
number of days. User can select from 00days to 99days.
Date Format
The default is dd-mm-yyyy.
Other date formats available are: mm-dd-yyyy / / yyyy-mm-dd.
31
Quantum Plus installation and user manual
Time/DST Setting
To set the DST, the simplest way is to set the DST box in the menu to the country required. If
the relevant country is not available then set the DST box to User Define, fill in the date and
time that the time changes are due to occur
PLAYBACK FOLLOWING TIME CHANGE
The DVR uses the time and date to index video on the hard disk drive so you can find it later.
Changing the time can cause the DVR to work improperly, when you try to play back video. If
you set the hour ahead, this is not a problem. But, if you set the hour back, there will be more
than one recording with the same time stamp.
Such as during the October Daylight Saving Time changeover, if you try to search for video
between 1 am and 2 am, the recorder may not operate properly because there will be two
hours of recorded video during this time period. To view video during this overlapping time
period, you must start playback before 1 am, then recorder will play both hours between 1
am and 2 a.m.
You cannot do a backward search through the overlapping time. But, you can do forward
search.
The Time and Date and the DST time can be changed from the front panel, the Mouse or the
Remote Control
32
Quantum Plus installation and user manual
Video Type
Video Type can set in this menu without rebooting or initialisation. The default is PAL, NTSC
can also be selected
System ID
The remote control can be used to control up to 16 Quantum‟s, the ID number on each can
be set to a unique address so that the remote will only control one at a time if they are in
close proximity. The default is 11.
Use the right arrow to select then the up and down arrow to change the ID number.
To select a unit on the remote control press the ID button, followed by the number, followed
by the ID button again. The LED will flash slowly.
33
Quantum Plus installation and user manual
Initialization
All the menu settings will be returned to the factory default. To carry out this function the
system recording will have to be turned off.
Information
The Information Screen shows the hard disk size, current firmware revisions, IP address and
MAC address
Disk Format
Formatting of the drive is used when new drives are installed or you need to wipe all
information on the disk.
34
Quantum Plus installation and user manual
Password Change
The password can be change from the factory default to a more secure one, a note of any
new password should be taken and stored in a secure place.
CLIENT ACCOUNT
When viewing over a network up to 6 connections can be made simultaneously, one can
have complete control e.g. view live and playback, and the other 5 can view live only.
Network users can be set up under this menu; a name and password need to be entered for
each account.
Once setup they will appear in the User1~5 section of the page.
35
Quantum Plus installation and user manual
Program Update
Always turn off: Recording, Playback and Network access while upgrading the unit
The latest firmware version can be upgraded through USB 2.0 Port using Memory Stick or
CD/DVD Media. When a memory stick is connected to the USB port, this symbol
will be shown in the status bar of the screen.
Enter “menu”-> “System Set”-> “Program Update”. If the system recognizes the new
firmware then, “New program found” will be displayed on the screen.
Next press the “SELECT” button.
Processing percentage will be displayed.
NOTE.
1. If the system doesn‟t recognize the new firmware, “New program not found” will be
displayed.
2. USB compatibility has been tested successfully with: Lexar Jumpdrive 128/256MB,
Sandisk Mini Cruzer & Cruzer Micro 2GB, KINGSTONE 2GB, A-DATA 2GB, IMATION 2GB,
SANDISK 1GB, SANDISK 512MB, MARUZEN 1GB
3. For system stability, please turn off 1) recording 2) playback 3) network connection during
upgrading.
4. After updating program, reboot the DVR. The simplest way is press POWER button and
enter the password.
36
Quantum Plus installation and user manual
SENSOR
The 16 alarm inputs and 1 output on the rear of the Quantum can be configured to be
normally open (N.O), normally closed ( N.C) or None.
37
Quantum Plus installation and user manual
PTZ Setup
The Quantum Plus can control PTZ cameras via an RS485 connection from the rear of the
DVR. The cameras can have individually selectable Protocols with a choice of Vista PD,
Pelco P or Pelco D. The Baud rate can also be selected.
PTZ Controller
The Quantum DVR needs to be setup to accept the VKBD3im keyboard, as a default this will
be set to the correct Protocol and Baud rate, the ID RS485 Address my need to be adjusted
dependant on the number of PTZ cameras on the system. The Keyboard ID should not be
the same as any of the domes on the system.
38
Quantum Plus installation and user manual
Telemetry connections and User Instructions
Remote Keyboard Connections
The connection of the VKBD3im keyboard to the Quantum Plus DVR, is made via the push
connectors marked as Keypad on the rear of the DVR
Use the break out box and one of the RJ45 Leads supplied with the VKBD3im keyboard.
Connect pin 3 of the break out box the Keypad (+VE)
Connect pin 6 of the break out box to the Keypad (-VE)
3
6
Connect the break out box to the keyboard using the RJ45 patch lead.
More detail can be found in the VKBD3im manual
39
Quantum Plus installation and user manual
RS485 Dome Telemetry connections
The connection to RS485 domes is made via the push connectors marked as Camera on the
rear of the Quantum.
The domes can be wired either in a Daisy chain or star configuration, examples shown below.
If using a Star configuration you require a “VSD16” RS485 star driver.
Daisy Chain configuration
Star Configuration
40
Quantum Plus installation and user manual
PTZ user instructions
The telemetry function of the Quantum Plus can be controlled via 4 different methods:
1.
2.
3.
4.
VKBD3im keyboard
Front panel buttons
Remote control
Software viewer
VKBD3im Keyboard
– See keyboard manual for control of PTZ cameras
Front Panel
Camera selection
The PTZ cameras can be controlled in either full screen or split screen mode. If in full
screen mode press the camera selection key
, the camera icon will step from one
camera to the next on the split screen. When the icon appears on the camera to be
controlled then press the PTZ key
.
If in full screen mode then simply press the PTZ key
.
Pan and Tilt control
To move the dome left / right / up or down use the arrows keys
Zoom and Focus control
To select Zoom and Focus press the Zoom Key
,
Zoom + =
Zoom - =
Focus Near =
Focus Far =
41
.
Quantum Plus installation and user manual
Preset positions
1. To store a preset position
Move the camera to the required position then press the record key
followed
by the number key of the preset to be stored (1 – 9)
2. To recall a Preset
Press the search key
followed by the number (1 -9).
Run Tour 1
To run Tour 1, press the search key
followed by the number 0 ( Zero). The
tour requires a keyboard to set it up in the domes menu.
Remote control functions
Camera selection
The PTZ cameras can be controlled in either full screen or split screen mode. If in full
screen mode press the camera selection key
, the camera icon will step from one
camera to the next on the split screen. When the icon appears on the camera to be
controlled then press the PTZ key
.
If in full screen mode then simply press the PTZ key
.
Pan and Tilt control
To move the dome left / right / up or down use the arrows keys
42
.
Quantum Plus installation and user manual
Zoom and Focus control
To select Zoom and Focus press the Zoom Key
,
Zoom + =
Zoom - =
Focus Near =
Focus Far =
Preset positions
3. To store a preset position
Move the camera to the required position then press the record key
followed by the number key of the preset to be stored (1 – 9)
4. To recall a Preset
Press the search key
followed by the number (1 -9).
Run Tour 1
To run Tour 1, press the search key
followed by the number 0 (Zero). The
tour requires a keyboard to set it up in the domes menu.
Software Viewer – see instructions on pages 95 and 96 of this manual.
43
Quantum Plus installation and user manual
NETWORK
(If the DVR is connected to a network, this icon will be shown in the OSD display)
To enter Network set menu, system will ask for a password (Default is 00000000).
With in the Network menu the DDNS (Dynamic Domain Named Server), IP addresses, NTP
and Live can be set.
DDNS
What is DDNS?
DDNS is a service that maps Internet domain names to IP addresses. DDNS serves a similar
purpose to DNS: DDNS allows anyone hosting a Web or FTP server to advertise a public
name to prospective users.
Unlike DNS that only works with static IP addresses, DDNS works with dynamic IP
addresses, such as those assigned by an ISP or other DHCP server.
What this means is that the DVR does not need a Static IP address to be available for
viewing remotely over the World Wide Web.
Please refer to Appendixes 4 on how to set up the DDNS service.
44
Quantum Plus installation and user manual
IP SET
When a fixed IP address is being used, the Use Dynamic IP should be set to NO
The IP Address, Gateway and Subnet Mask need to be set, these will generally be given by
the Network Manager.
DSL refers to all types of Digital Subscriber Line such as ADSL and SDSL.
NTP
The Network Time Protocol Setting allows the DVR time to be synchronised with an external
time server.
The default is NTP OFF. When turned on the Type of service can be selected, options are
Default (time.bora.net), Domain and IP. As shown in next diagram:
45
Quantum Plus installation and user manual
The Time zone can also be chosen within the City selection.
LIVE
It allows a separate Live resolution and Quality, regardless of System Recording and Quality,
to be set, this helps optimise the network streaming.
46
Quantum Plus installation and user manual
5. Event
This section is used to inform the user as to an event occurring, this can be by the sounding
of a buzzer or by sending an E-mail to a predefined address.
E-Mail Registration
Within this section up to 3 users can be set-up to receive an email on the occurrence of an
event such as Video Loss / Alarm / Motion or Power Loss. An E-mail will only be sent if the
Quantum Plus is sitting on a network with access to the Internet, e.g. through a router.
The e-mail addresses are set via the alphanumeric buttons on the front panel, or from the on
screen keyboard via the mouse.
47
Quantum Plus installation and user manual
For SENDER MAIL ID and SENDER DOMAIN, this is best explained by an example, if the
following is input:
SENDER MAIL ID: QUANTUMPLUS
SENDER DOMAIN: NORBAIN.CO.UK
Then the receiver will receive a mail from QUANTUMPLUS@NORBAIN.CO.UK
Note: This is not a valid e-mail address for replies.
SEND TEST MAIL sends a test E-mail to the addresses so allowing the installer to verify if
the setup is correct.
SMTP Mode
The SMTP function allows e-mails to be sent over a LAN
The default is SMTP Mode “OFF”.
In order to activate SMTP Mode, choose SMTP Mode either IP or Domain first.
Then, put ID, Password, IP address, and port.
Finally press “SMTP Status Check” to see whether it works.
Please see the screen shots that follow:
48
Quantum Plus installation and user manual
E-mail Out
As well as e-mail on event activations the Quantum can be set to send a report of what has
happened daily / weekly or immediately. This sends a mail containing the log report.
49
Quantum Plus installation and user manual
Beep Out and Alarm Out
When an event (e.g. Video loss, Alarm, Motion or power loss) occurs the following
actions can be triggered:
E-mail – As described in previous section
Beep – The buzzer can be sounded.
Alarm out – The relay contact on the rear of the unit can be closed.
50
Quantum Plus installation and user manual
SEARCHING VIDEO FOOTAGE
To access the search option, press the SEARCH button on the front panel or right click the
mouse and select Search, (A password may have to be entered) after which the following
screen will be displayed.
Date / Time Search
If you select date/time search, the following will be shown. Use the numerical number on the
front panel or the mouse to select the time and date required, then select Play.
EVENT
This allows the user to select between ALARM, MOTION or AUDIO. Select required option
by pressing the right arrow, or selecting with the mouse.
ALARM – The search is for any alarm activation within the times defined.
MOTION – The search is for any motion events within the times defined.
AUDIO – The search is for any audio activations within the times defined.
51
Quantum Plus installation and user manual
Calendar Search
Following screen is displayed when “Calendar” search is selected.
The Calendar search gives a graphical representation of when video is recorded on the hard
drive.
The year and month can be selected. This month is shown as a calendar on the screen, any
day which contains recorded video will be indicated by a highlighted number in white.
Move to the desired day by using the up / down / left / right buttons, Select the day by
pressing SEL.
The following screen will be displayed.
Hours of the day
52
Quantum Plus installation and user manual
The hours which have recorded data are displayed as a coloured bar. Select the hour which
you want to review, the following screen will be displayed.
Minutes
hour
in
the
The minutes which have recorded data will be displayed as a coloured bar, click on the time
required; the recorded data will be played back from this point.
* Preview function
Before actual viewing of recorded data from the calendar menu, it is possible to preview the
selected time and date on the screen behind the search window. This is done by selecting a
time and pressing the “ZOOM” button on the front panel. If a different time is required, select
it and press “ZOOM “again.
53
Quantum Plus installation and user manual
Archiving Evidence to DVD/CD or USB
Once the required video has been found, it may be necessary to down load it for evidential
purposes. This can be done either onto the internal CD/DVD-R writer or via the USB port on
the front of the Quantum Plus.
To do this press the SEARCH button and using the down button move to ARCHIVE, once
highlighted press SEL, the following screen will be displayed.
Device
This allows selection between the internal CD /DVD-R writer and the FLASH option via the
USB port, when highlighted use the right arrow to toggle between the options.
Device Format
Format for CD/DVD-R is not needed. When using a USB pen, the format should be done
first.
Type
EXCLUSIVE file type
If evidence is downloaded as an Exclusive file, the Quantum Plus will download bespoke
player software on to the CD / DVD or USB device along with the evidence. This means that
no special software is required, by the reviewing PC. This format is secure and watermarked.
54
Quantum Plus installation and user manual
LOG
The Log file can be downloaded from this menu screen, simply tick the LOG box and do not
select any camera channels, then select transfer.
From/ To
You can set up the start and stop time which is required to be backed up to the internal
CD/DVD-R or USB device.
Highlight this option, then press SEL, then use the alphanumeric buttons or the mouse to set
the time and date. Repeat for the end time.
Channel
As long as the EXCLUSIVE file format is selected, the number of channels to be down
loaded can be selected. Anything from a single channel to all 16 can be selected.
Calculate Archive size
Once the time and date and file format have been entered, it is necessary to confirm that the
size of file created will not exceed the size of memory available on the disk or USB device.
Move to Calculated Archive size and press SEL.
The Quantum Plus will then calculate storage space required for download file. This will be
displayed in the Required Size section. As long as the Required Size is smaller than the
Free/ total space, then move to Transfer and select it.
Transfer
When Transfer is highlighted press SEL, the downloading will start. Percentage done during
downloading will be shown.
* USB compatibility: the following have been tested
Lexar JumpDrive
128/256MB
SanDisk Mini Cruzer
SanDisk Cruzer Micro
128MB
256MB, 512GB, 1GB
KINGSTONE
2GB
A-DATA
IMATION
MARUZEN
DVD/RW Plextor
2GB
2GB
1GB
PX-716UFL
Lite-On CD/RW
(LTR-52327SX)
55
Quantum Plus installation and user manual
LOG
The log file contains information on the following:
Power:
Record:
Operation:
Client:
Event:
Power on, Power off, Power fail
Rec fail, Rec start, Rec stop, Rec error, Rec full
Play start, Play stop, HDD format, Menu set
R_Login, R_Logout, R_Logfail, R_Play, R_Transfer, R_Rec on, R_Rec off,
R_Upgrade
Alarm, Motion, Audio, Video loss, Email fail
A total of 2500 events can be recorded the oldest being overwritten when a new one occurs,
they can be viewed all together or as individual types..
56
Quantum Plus installation and user manual
Client Viewer software – QT Player
Each Quantum comes with license free viewer software to view the Quantum across a
network.
To be able to do this the recommended minimum specification for the PC is as follows:
Minimum PC specification
> CPU: Core 2 Duo 1.8GHz,
> Graphic Memory: 256MB
Installing software
When you put Quantum Network installation CD into your PC, it will auto run and lead you
through an installation wizard. Follow the instructions. Once the software is loaded it will
automatically run.
Connection
To connect to the Unit, open the Viewer Software and click the connection button,
57
Quantum Plus installation and user manual
LOG IN
The following window will appear. To connect to the Quantum, enter the units: IP address;
DVR Port (2000 ids default), ID and Password. Then, click “OK”, to start the live monitoring.
Explanation of Screen Buttons
58
Quantum Plus installation and user manual
Live Monitoring
The software is best viewed with the PC monitor resolution, set to: 1024 x 768.
Split Screen options (1, 4, 6, 7, 8, 9, 10, 13,16):
Spilt Screens can be viewed during both live and playback. The splits screens available are:
full screen,4,6,7, 8,9,10,13 and 16 way.
1) Full Screen
2) 10 Way
59
Quantum Plus installation and user manual
Full Screen on/ off
When the full screen button is
selected, a tool bar offering the
various split screen options, and
the Exit key will be displayed at
the bottom of the screen.
OSD on/off:
The OSD button will toggle
between the On screen
titles etc being shown or
hidden
(SMART)ARRANGE ON/OFF:
If Cameras are being displayed in segments that are not logical, the Smart button will
rearrange and put camera input 1 into segment 1 etc.
60
Quantum Plus installation and user manual
Image Save / Load:
/
SAVE: This icon is used to save a still image in either JPEG or BMP or TIF format. There is
no change on the main screen when the “Save” icon is pressed.
LOAD: This icon is used to retrieve and view a saved still image, when selected a list of
available images will be shown. Select to one required, it will be displayed along with data
information (Status-Live/Playback, IP address, CH No.).
Playback (Step Backward, Backward, Playback, Pause, Recording, Stop, Step
Forward)
Audio (Mute, Volume, Select Audio, Microphone)
Select Audio: Toggles through audio channels.
Microphone: It is used for transmitting audio to the System through a microphone.
61
Quantum Plus installation and user manual
Remote search
Search (Date/Time/Event/Calendar), Archive (Remote Archive), Log (Remote Log) are
available.
SEARCH
This Remote Search is able to play back video on the PC direct from the hard disk storage
on the Quantum Plus. There are 3 options for as follows.
1) Date/Time
2) Event
3) Calendar
Date/Time
Enter the Date and Time, by using the
drop down buttons. Once set click on the
Play button.
Click “Play” button, this window
disappears and Remote Playback will
start.
To stop playing back press Stop
then press live
.
Event
Select the type of Event to be searched
for, by clicking on the either: Alarm,
Motion or Audio at top of screen.
A list of the available events will appear.
To play an Event select it and click Play.
To stop playing back press Stop
then press live
62
.
Quantum Plus installation and user manual
Calendar
Select the date required (as long as the date is highlighted in Blue there is recorded data on
from that day).
There are 3 options for selecting the required time once the date has been selected.
1) Drag the Red line along the colour bar (I.e. Blue: Normal Recording) till the required time
is reached.
2) Click on the required time for playback on the blue bar then the red line will move to this
point.
3) Hover over the time box, a drop down arrow will appear allowing the manual selection of
Hours, mins and seconds.
Next click the “Play” button for Remote Playback. Or, click “Prev” to go back to previous
stage.
63
Quantum Plus installation and user manual
Select Channel:
Channels can be included or excluded
dependent on query. This is available within
Search, Backup and Logs.
.
ARCHIVE
- Remote Archive – Date/Time
Enter the Start and End dates and times, by
hovering over the selections, a drop down box
will appear.
Once selection is made, then “click” calculate,
the file size will be displayed. Finally click
“Archive”, the file will be transferred to
C:\QTplayer\Download.
- Remote Archive – Event
Select either: Alarm, Motion or Audio
from the top of the screen. A list of
events will appear.
Click on the event required, it will be
come highlighted.
Click on Calculate, the file size will be
calculated, this may take a few
seconds.
Finally click Archive; the file will be
transferred to C:\QTplayer\Download.
64
Quantum Plus installation and user manual
- Remote Archive – Calendar
Select the date required (Days with recorded video a data present are highlighted in Blue)
There are 3 options for selecting the required time once the date has been selected.
1) Drag the Red line along the colour bar (I.e. Blue: Normal Recording) till the required time
is reached.
2) Click on the required time for playback on the blue bar then the red line will move to this
point.
3) Hover over the time box, a drop down arrow will appear allowing the manual selection of
Hours, minutes and seconds.
Then click the “Next” button to set “End” Archive time, in the same manner.
65
Quantum Plus installation and user manual
The backup procedure is same as Date/Time & Event backup as previous page.
* “Prev” to go back to previous stage.
*The downloaded data is saved in the follows location.
C:\QTplayer\Download
66
Quantum Plus installation and user manual
Remote Log
The Log file can either be printed or if viewing the Event Log, the recorded Event can be
played, by selecting it and clicking on Play.
The log list can be viewed as a whole or filtered by the following types:
Power:
Record:
Operation:
Client:
Event:
Power on, Power off,
Rec fail, Rec start, Rec stop, Rec error, Rec full
Play start, Play stop, HDD format, Menu set
R_Login, R_Logout, R_Logfail, R_Play, R_Transfer, R_Rec on, R_Rec off,
R_Upgrade
Alarm, Motion, Audio, Video loss, Email fail.
Info
- “System Info” of the Remote Log
The system info displays the Mac
address and software version
information.
- “Status Info” of the Remote Log
This shows the status of both the
Hard disk and the recording modes of
each channel.
67
Quantum Plus installation and user manual
Remote Setup: Checking settings menu (Same as DVR)
1) Display
– Camera Setting
Within this setting the Hue, Saturation,
Contrast and Brightness can be adjusted
on a camera by camera basis.
– Camera Covert
Cameras can be remotely set into Covert
Mode, they are still being recorded but
cannot be viewed local to the system, or by
any remote user apart from the Administrator
on line.
68
Quantum Plus installation and user manual
- Camera Name
Up to 32 Characters are available for each
camera name.
- Spot Monitor settings
1) Set “Mode” (Split screen/ Alarm Motion or Event), by click the ON button for the
required state – It will turn red.
2) Next select Duration for a sequence using the white time bar, next click OK.
69
Quantum Plus installation and user manual
OSD On/Off
The Symbols and text displayed on screen
can be controlled:
1. The status bar can be set to be off/
Always on or be on for 5 or 10
seconds after a key press.
2. The Event symbols such as Motion,
Audio, Pan / Tilt can be displayed or
turned off.
3. The camera name can be displayed
or turned off.
70
Quantum Plus installation and user manual
Recording
Global
1. Watermark – security tagging of
recorded video.
2. HDD Overwrite – When the disk is
full it will overwrite the oldest data.
3. Pre Resolution – Picture quality for
pre event recording.
4. Pre Frame Rate – Picture rate for pre
event recording.
5. Pre Duration – Length of pre event.
6. Post Duration – Length of recording
post event.
7. Quality – Quality.
Normal
Resolution
Each camera can individually have its
Resolution, Record rate and whether
Audio is active set from this screen.
71
Quantum Plus installation and user manual
Rate
Audio
72
Quantum Plus installation and user manual
Alarm
The Alarm settings for Resolution, Rate and Audio are configured in the same manner as
Normal (Time lapse) see pages 71 and 72.
Motion
The Motion settings for Resolution, Rate and Audio are configured in the same manner as
Normal (Time lapse) see pages 71 and 72.
The only additions are the setting up of Sensitivity and the motion detection grid per camera.
Motion Sensitivity
The sensitivity of motion detection
can be set on a per camera basis,
the sensitivity will have to be
adjusted to suit the individual
scenes and may require several
adjustments to achieve optimum
performance.
The detection region setup screen
is displayed by clicking the
Region button.
Region
Each cameras motion detection grid
can be individually tailored for the
camera scene. They are set to a
default of all on (Yellow).
They can all be turned off by clicking
“Unselect all”. Then individually
selecting the required boxes or
clicking and dragging over an area.
Once set click OK.
73
Quantum Plus installation and user manual
Schedule
The Schedule settings for Resolution, Rate and Audio are configured in the same manner as
Normal (Time lapse) see pages 71 and 72.
The only addition is the setting up of Schedule grid, click on the SET button to display the
following screen..
A timetable can be set in hourly
blocks throughout the whole
week.
Audio Event
The Quantum Plus can start recording when it detects an Audio event.
The Schedule settings for Resolution, Rate and Audio are configured in the same manner as
Normal (Time lapse) see pages 71 and 72.
The only difference is to setup the sensitivity of the audio.
74
Quantum Plus installation and user manual
Duration
The duration setting allows the user to choose the Resolution and length of time the unit
records for, then the DVR will automatically adjust the rate at which it records to achieve this
time period.
-Resolution
First select the resolution required
for each camera.
-Video
Next select whether the camera is
connected to the DVR.
75
Quantum Plus installation and user manual
-Audio
Next select if Audio is being recorded
on that channel.
-Days
Finally select the number of days the
DVR should record for. The choice
being between ; 5,10,20,30,40,50,60,70
80 or 90 Days.
76
Quantum Plus installation and user manual
Priority
The RECORD PRIORITY allows the
mixing of the various record methods to
customise
the
individual
site
requirements.
Example: A site may require Alarm
recording at night, then a standard FPS
recording during the day. In this case
the Schedule would be set for required
FPS and resolution, and the timetable
set for this recording between 8am and
8pm each day. Schedule would be set
as 1st Priority. The Alarm settings would
be configured as required and this
would be set as the 2nd priority.
The
Quantum
between
8am
would
and
then
8pm
record
at
the
Scheduled rate, then once beyond 8pm
would look to the second priority and
only record Alarm Events.
77
Quantum Plus installation and user manual
System
Basic
This section is used to select:
Language
Date format
Video type
System ID
Live viewing resolution
Quality
Client Account
5 separate Client accounts can be set-up
with individual user names and
passwords.
This is useful for tracking in the log, who
has accessed the DVR over the network.
78
Quantum Plus installation and user manual
Sensor
Each of the 16 alarm inputs can be
configured to be either inactive
(NONE), or Normaly Open (N.O), or
Normally Closed (N.C).
Auto Delete Mode
In Auto Delete Mode the DVR can be
set to delete recordings that are a
certain numbers of days old.
This allows the DVR to comply with
data protection laws in certain
countries such as France.
79
Quantum Plus installation and user manual
PTZ Setup for Cameras
-ID
Each camera input can be allocated an
RS485 ID between 1 and 255.
-Protocol
Each camera output can have an RS485
protocol associated with it, the choices are:
80
Quantum Plus installation and user manual
-Baud Rate
The Baud rate of each PTZ camera can
be set the choices are:
PTZ set up for Keyboard
-ID
Each Keyboard can be allocated an
RS485 ID between 1 and 255.
Vista VKBD3im addressing switches are
inside the keyboard, refer to keyboard
manual for setting address.
81
Quantum Plus installation and user manual
Protocol
Each keyboard can have an RS485
protocol associated with it, the choices
are:
Choose Vista-KBD for the VKDB3im
keyboard.
-Baud rate
The Baud rate of each PTZ camera can be
set the choices are:
Choose 9600 for the VKDB3im
82
Quantum Plus installation and user manual
DST Setup
The Quantum can be set to automatically reset its clock when the clocks change for Day
Light Saving time. As default this is set to Off.
USER Define
Change “Off” to User Define, this will allow
the exact date and time for the change to
occur. Alternatively
Select Region
Select the required country.
Then click “Ok”.
83
Quantum Plus installation and user manual
NTP Setup
NTP setup allows the DVR to have its internal
clock synchronised with an External clock.
The default setting is “Off”
To set up hover on the “Off” a drop down arrow
will appear giving the option to turn “On”.
Once “On”, two other options will appear:
Type allows selection between:
Default – Time server is “time.bora.net”.
Domain – Where another time server name
can
be added.
IP – Where an IP address for a time server can
be input.
Select City
Once the NTP settings have been set, you
must then tell the DVR which time zone you
are in. This will allow it to offset any time
differences if the time server you contact is in
a different zone.
Select City, the map screen will appear.
Hover over the city selection box, a drop
down arrow will appear, click on the arrow. A
list of time zones will be displayed. Select the
time zone where the Quantum is located.
The Click OK.
84
Quantum Plus installation and user manual
EVENT
Email Registration
The Quantum Plus will send E-mails to
up to 3 defined addresses under
certain conditions such as Alarms or
video loss. The screen is where you
setup the receiving address and
address that the DVR will send from.
The mails can be set to be sent
immediately an event occurs, Daily or
Weekly.
Email Out
The actions which cause an e-mail
response can be defined within this
screen.
85
Quantum Plus installation and user manual
Beep Out
The internal buzzer can be set to sound
on the following occurrences:
Video Loss
Alarm activation
Motion Detection
Power loss
The duration of the buzzer can be set.
Alarm Out
The Alarm output relay can be set to
activate on the following occurrences:
Video Loss
Alarm activation
Motion Detection
Power loss
The duration of the relay closure can be
set.
86
Quantum Plus installation and user manual
Local Search
This allows playback of video which has been downloaded top the PC.
Search
Searches can be done by Date/Time, Even and Calendar.
Date/Time
Hovering over the Date and Time bars
will allow drop down boxes to select the
required time and Date.
Once set, click Play.
Event
Choose the Event search box then choose the
type of Event you are searching for, options
are: Alarms, Motion or Audio.
Once the selection is made, a list will appear,
choose the Event required and click Play.
87
Quantum Plus installation and user manual
Calendar
When the Calendar option is chosen this
screen will appear, any day with
recording available will be highlighted in
Blue.
Select the required day.
Any downloaded event s will be shown,
click on the event, the red line will move to
that event. Then click Play to review the
recording.
88
Quantum Plus installation and user manual
Log
Clicking on Log will display the log file
from the unit.
This file can be printed, by clicking Print.
Info
Clicking on Info, will display the version
of the software client being used.
89
Quantum Plus installation and user manual
Local Setup
This allows the setup of the viewing of the software on the PC.
Global
This screen allows the following:
Draw mode to be set to YUV or RGB
Date Format to be set to: DD/MM/YYY,
MM/DD/YYYY or YYYY/MM/DD.
Save Format, for the saving of stills as
either JPEG, Bit Map or TIF.
Location for where stills are saved.
Opacity
The opacity or “boldness” of the OSD
can be individually set per function.
The lower the number the more see
through the box.
90
Quantum Plus installation and user manual
Audio Buffer
Audio Buffer settings are there to adjust the
audio over the network, this will
compensate for different network speeds
( LANs, WANs etc).
This can only be adjusted if the LIVE video
is switched off.
Adjust each variable to achieve best quality
video for Network bandwidth available, this
is best done through trial and error.
91
Quantum Plus installation and user manual
PAN, TILT, Zoom, Focus
When PTZ button is being pressed, PTZ
control icon will be pop-up on the live
image.
PAN/TILT/ZOOM/FOCUS
When PAN/TILT button
is
clicked the Pan/Tilt control appears,
this allows Left, Right, Up and Down
Control of PTZ cameras
When Zoom/Focus button
is
clicked, the control changes to Zoom
in on the up arrow, Zoom out on the
down arrow. Focus near on the left
button and focus far on the right
arrow.
92
Quantum Plus installation and user manual
PRESET/LEARN
PRESET&LEARN icon
The presets button can be activated by clicking on the centre of the control icon, the
preset symbol will appear and the Preset selection box will appear.
To save a preset, move the camera to the desired position then click “Set” followed by
the desired number.
To recall the preset, click “Call” followed by the desired number.
93
Quantum Plus installation and user manual
Firmware Upgrade
User can select Firmware Upgrade menu, if a new version of firmaware exits in the
C:/QTplayer/Upgrade folder ,then the message „New program found!‟ will be displayed if
there is no file then „New program not found!‟ message will be displayed.
To proceed with upgrading press the OK button and select each firmware files to upgrade it
to the system, by ticking the boxes.
Once the upgrade has been completed the following message will appear.
Next press the OK button to reboot the DVR, the firmware will only be applied completely
once the system is rebooted.
Quit (Stop Client program)
To exit the Client viewer program click the Quit button.
94
Quantum Plus installation and user manual
APPENDIX 1
ALARM SENSOR INSTALLATION
1. Components
1) External Sensor: 1
2) DVR System: 1
2. Inner Circuit for Sensor Input
The inner circuit of Quantum DVR is as follows,
DVR
12V DC
5V DC
2.2k
2.2k
Internal Check Point
0.1uF
PC817
SENSOR IN
Outlet Point
GND
① PC817 : Photo Coupler
② The Specification of PC817
95
Quantum Plus installation and user manual
 Absolute Maximum Ratings
Parameter
Forward current
*1Peak forward current
Input
Reverse voltage
Power dissipation
Collector-emitter voltage
Emitter-collector voltage
Output
Collector current
Collector power
dissipation
Total power dissipation
*2Isolation voltage
Symbol
IF
I FM
VR
P
V CEO
V ECO
IC
Rating
50
1
6
70
35
6
50
Unit
mA
A
V
mW
V
V
mA
PC
150
mW
P tot
V iso
200
5 000
-30 to +
100
-55 to +
125
260
mW
V rms
Operating temperature
T opr
Storage temperature
T stg
*3Soldering temperature
*1 Pulse width<=100s, Duty ratio : 0.001
*2 40 to 60% RH, AC for 1 minute
*3 For 10 seconds
T sol
°C
°C
°C
 Electro-optical Characteristics
Input
Output
Parameter
Forward voltage
Peak forward
voltage
Reverse current
Terminal
capacitance
Collector dark
current
*4Current transfer
ratio
Collector-emitter
saturation voltage
Isolation resistance
Transfer
characteristics
Symbol
VF
MIN.
-
TYP.
1.2
MAX.
1.4
Unit
V
IFM = 0.5A
-
-
3.0
V
IR
V R =4V
-
-
10
µA
Ct
V = 0, f = 1kHz
-
30
250
pF
V CE = 20V
-
-
10 -7
A
50
-
600
%
-
0.1
0.2
V
5x
1010
1011
-
Ω
V FM
ICEO
CTR
V
CE( sat)
R ISO
Conditions
IF = 20mA
IF = 5mA, V CE =
5V
IF = 20mA, I C =
1mA
DC500V, 40 to
60% RH
Floating
capacitance
Cf
V = 0, f = 1MHz
-
0.6
1.0
pF
Cut-off frequency
fc
V CE = 5V, I C =
2mA, R L = 100
W, -3dB
-
80
-
kHz
-
4
18
µs
3
18
µs
Response
time
Rise
time
Fall
time
tr
tf
V CE = 2V, I C =
2mA, R L = 100
Ω
96
-
Quantum Plus installation and user manual
1. SENSOR Install Processing
① Please refer the below block diagram.
AC
SENSOR
DVR
12V DC
?? V DC
2.2k
N.C
3.3k
Or 10k
PC817
SENSOR IN
Outlet Point
GND
97
Quantum Plus installation and user manual
APPENDIX 2
SETTING INTERNET SECURITY SETUP FOR WEB CLIENT ON
WINDOW XP/2000 & WINDOW VISTA SERVICE PACK 2.
1) Security Setup
> Window XP / 2000
> Window Vista
Tools-> Internet Options-> Security
-> Unselect square box ->
Select “Customer Level”
Tools-> Internet Options-> Security
-> Select “Customer Level”
Select “ Allow script-initiated windows
Without Size or position constraints”->
Enable.
98
Quantum Plus installation and user manual
Select “Download unsigned Active X
Controls”-> Prompt
Select “ Automatic Prompting for Active X
Controls”-> Disable
99
Quantum Plus installation and user manual
2) Connection
Click here as described
Select “Temporary Allow
Pop-ups”
Click “To help protect security,
Internet Explorer stopped this
site from installing an Active X
control on your computer. Click
here for options…”
100
Quantum Plus installation and user manual
Select “Install Active X Control “
Select “Install” and then „Log-In‟ box
will be shown.
101
Quantum Plus installation and user manual
APPENDIX 3
DYNAMIC IP (Supporting DDNS Server)
With DDNS Server, This allows a user to connect to the unit remotely without the
need for a fixed IP address.(Please register your ID & Domain at www.ddns-dvr.com
in which you can use their DDNS server as free of charge)
1. Visit www.ddns-dvr.com to get the DDNS user ID & PW as well as Host name.
2. Click to create / set account of “Dynamic DNS”.
3. Select “Create Account” menu.
102
Quantum Plus installation and user manual
4. Create Account.
> Fill in all blanks in order to create new account.
ID & Password will be emailed to you when the account is setup correctly.
Once the DDns-Dvr account has been setup, it is necessary to add the details in the Network
section of the Quantum‟s menus.
DDNS SET
To enter Network set menu, system ask password (Default is 00000000).
In DDNS environment, need to be changed DVR & Web server port, please refer to
IP set.
103
Quantum Plus installation and user manual
Set up DDNS
1. Change DDNS to ON
2.
Input User ID
3.
Input User PW
4.
Input Domain
5.
Click “DDNS Status Check” if it is “ok” Click “Apply”
> Note; In DDNS Setup, The Domain Name has to be filled in.
104
Quantum Plus installation and user manual
Appendix 4
SETUP FOR DVR PORT/ WEB SERVER PORT USING IP SHARING ROUTER
(Port Forwarding)
1) To use IP sharing Router, “Use Dynamic IP” should be set to “NO”.
- DVR Port: This can be set to any number between 2000 to 65535.
- Web Server Port: this can be set to any number between 2000~65535, as long as
it is not the same as the DVR Port number
2) Setup “virtual server” on IP sharing Router
It is for setting virtual server to forward IP which is allotted to DVR.
> For example,
DVR-1, IP : 192.168.10.107, DVR Port : 7000, Web Server Port : 7001
If DVR-1 is configured as above, the virtual server on IP sharing router is as follows.
1) PC Server Name : DVR-1(IP 192.168.10.107)
Protocol : TCP, Internal Port : 7000, External Port : 7000
2) PC Server Name : DVR-1 (IP 192.168.10.107)
Protocol : TCP, Internal Port : 7001, External Port : 7001
* For more detail, please refer to relevant IP sharing manual.
105
Quantum Plus installation and user manual
(3) „DDNS‟ Setup on IP sharing router
DDNS configuration is not needed in case of fixed IP.
(4) To connect DVR-1 with Internet Explorer, http://dvr-1.ddns-dvr.com:7001,
to connect DVR-1 with CD installer, http://dvr-1.ddns-dvr.com:7000.
106
Quantum Plus installation and user manual
APPENDIX 5
MAKING A PARTITION ON AN EXTERNAL USB HARD DRIVE
To back up to USB HDD, the USB HDD should be formatted first on PC. The
Quantum PLUS supports the FAT32 & NTFS file system, of which maximum size is
500GB for one partition. Please refer to the following procedure to make a partition
and format on PC.
*If the HDD capacity is under 500GB, you don‟t need to make a partition and simply
connect to the DVR directly.
1. Select Control panel-> administrative Tools.
107
Quantum Plus installation and user manual
2. Select “Computer Management”
3. Select “Disk Management”.
108
Quantum Plus installation and user manual
4. Click right mouse button and select “New Partition”.
5. Follow “New Partition Wizard” procedure as below.
109
Quantum Plus installation and user manual
6. Select the Primary partition option.
7. Maximum is 500GB at FAT32 file format.
110
Quantum Plus installation and user manual
8. Assign drive letter
9. Format the partition to FAT32
111
Quantum Plus installation and user manual
10. At this stage, New Partition has been made.
11.Check New partition was created correctly.(Format will run automatically)
112
Quantum Plus installation and user manual
12. Check New Partition was created correctly
113
Quantum Plus installation and user manual
APPENDIX 6
SPECIFICATION
114
Quantum Plus installation and user manual
This page is intentionally left blank
115
Quantum Plus installation and user manual
NORBAIN SD LTD
210 Wharfedale Road
Winnersh Triangle
Wokingham
Berks
RG41 5TP
01189 125 000
Subject to change without notice
116
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising