AEC FP1600 Specification
PRODUCT INDEX
Line Interactive
• Modified Sinewave (T1)
• Pure Sinewave (T2)
Online Double Conversion
• 1 Phase Input / 1 Phase Output (T3)
• 3 Phase Input / 1 Phase Output (T4)
• 3 Phase Input / 3 Phase Output (T5)
Specialist Networking Distributor
| CTN: 021 423 7115 | DBN: 087 943 9076
JHB: 011 351 9800
www.duxbury.co.za
4
6
11
19
23
Inverters
• Modified Sinewave (IG Series)
• Pure Sinewave (S, SK, SKX)
31
Accessories, Baterries & Cabinets
54
Transformers
14
33
POWER LINE DISTURBANCES
Dip (Sag): is a short term decrease in line voltage.
Usually it results from a short circuit in the power line or a sudden
increase in electrical load on the line (start up of large loads), utility
switching or equipment failure.
Surge: is the exact opposite of a dip. It is a temporary increase
in line voltage that lasts at least one cycle (approx. 16mS).
It can be triggered off by rapid reduction in power loads or by
utility switching.
Spike (transient): is similar to a surge except that it lasts
less than a full cycle (often only a few milliseconds).
It can be 100% or more above nominal voltage.
Electrical Noise: probably the most common type of disturbance,
which is a random high voltage, or high frequency interference on
the power line caused mostly by non-linear loads. There are two
types of noise, usually referred to as common mode (noise
between power connection and ground) and transverse mode
(noise between power connections).
Blackout: this is the ultimate power disturbance. It is a complete
cut in the power line supply (power failure). Typically described
as “zero-volt” condition lasting longer than half a cycle.
Can be caused by utility equipment failure, lightning etc . . .
the list is long.
Businesses are becoming more and more reliant on a utility
power supply that is pushed beyond its capacity. Despite
advances in the capabilities of modern personal computers,
a momentary power outage is still all it takes to lose your data.
More dangerous is the loss of previously written files, or even an
entire hard disk, which can occur should a power problem strike
while your computer is saving a file. Network file-servers
constantly writing to disk are particularly susceptible.
Some African countries, including South Africa, have resorted
to power rationing as a way to meet increasing demand.
In these cases, the question of whether or not to use power
conditioning, is no longer a choice.
Brownout: is a deliberate reduction in AC line voltage by the utility
company during periods of unusual high demand or insufficient
load capacity. The power line supply does not have the full capacity
to supply the load which results in load sharing.
HOW POWER PROBLEMS CAN BE AVOIDED
Below is a table of power problems and how to solve them.
Equipment
Available
Automatic
Voltage
Regulator (AVR)
Line
Conditioner
Offline UPS
Line
Interactive UPS
True Online UPS
Frequency
Converter
Surges
Limited
Protection (MOV)
Full
Protection
None or Limited
Protection (MOV)
Limited
Protection
Good
Protection
Good
Protection
Spikes
Limited
Protection
Full
Protection
None or Limited
Protection (MOV)
Limited
Protection
Good
Protection
Good
Protection
Sags
Good
Protection
Full
Protection
None or Limited
Protection
Limited
Protection
Full
Protection
Full
Protection
Noise
Limited
Protection
Good
Protection
None or Limited
Protection
Limited
Protection
Good
Protection
Full
Protection
Blackout
(Power Failure)
No
Protection
No
Protection
Good Protection
4ms-8ms
Changeover
Good Protection
Full
Protection (no break)
No
Protection
Frequency
Variation
No
Protection
Good
Protection
No Protection
Limited
Protection
Full
Protection
Full
Protection
Waveform
Distortion
No
Protection
Good
Protection
No Protection
Limited
Protection
Full
Protection
Full
Protection
CABLE SELECTION CHART
Cable Size
Armoured Cable
Free Air Wired
Unarmoured Cable
Free Air Wired
Cable Size
Armoured Cable
Free Air Wired
Unarmoured Cable Free Air Wired
2.5mm2
27 Amps
24 Amps
50mm2
150 Amps
140 Amps
4.0mm2
35 Amps
32 Amps
70mm2
180 Amps
175 Amps
6.0mm2
43 Amps
41 Amps
95mm2
225 Amps
215 Amps
10mm2
60 Amps
55 Amps
120mm2
260 Amps
250 Amps
16mm2
70 Amps
72 Amps
150mm2
290 Amps
280 Amps
25mm2
100 Amps
94 Amps
185mm2
340 Amps
330 Amps
115 Amps
240mm2
400 Amps
385 Amps
35mm2
2
125 Amps
POWER CONDITIONING & UPS
OVERVIEW OF DIFFERENT UPS TYPES
Most of the critical applications in data processing and other industries are now protected by Uninterruptible Power Supplies (UPS).
It is essential that the different types and performance levels are covered by international standards (IEC).
UPS systems are intended to improve the quality of AC power and provide a redundant (back-up) power source.
Power quality defects which may be improved by a UPS include surges, noise or sags.
AC
Input
Static
Switch
~=
Battery
Rectifier/
Charger
=~
Load
Inverter
In this type of UPS the load is isolated from the mains, hence all the power to the load flows through the inverter, offering continuous
protection and full isolation against surges, noise and sags. It offers true on line protection.
Simplified Diagram of an “Offline“ UPS
AC
Input
Filter
~=
Battery
Rectifier/
Charger
Load
=~
Inverter
This type of UPS is not suitable for all applications because it does not use a static switch bypass and the switching times are longer.
There is no isolation between the load and the mains. There is also no output frequency control.
Simplified Diagram of an “Line-Interactive“ UPS
AC
Input
Transfer
Switch
Inverter
AVR
=~
Load
Battery
This type of UPS does not provide isolation between the mains and the load. There is poor protection against spikes and poor efficiency.
There is no output frequency control but it has voltage regulation on the output.
3
UPS - LINE INTERACTIVE
MODIFIED SINEWAVE
T1X SERIES (650VA-2kVA)
•Compact size
•Excellent microprocessor control guarantees high reliability
•Boost and buck AVR for voltage stabilisation
•Auto restart with AC recovery
•Simulated sinewave inverter output
•Off-mode charging
•Cold start function
•USB comm. standard with RJ11 telephone protection.
Model
Capacity
ST1006X
ST1010X
ST1015X
ST1020X
650VA/360W
1000VA/600W
1500VA/900W
2000VA/1200W
Input
Voltage
110/120VAC or 220/230/240VAC
Voltage Range
81-145VAC or 162-290VAC
Frequency Range
50Hz or 60Hz (auto-sensing)
Output
Ac Voltage Regulation (Batt. Mode)
± 10%
Frequency Range (Batt. Mode)
50Hz or 60Hz ± 1Hz
Transfer Time
Typical 1-6ms, 10ms Max
Battery
Battery Type & Number
Backup Time (1 PC @ 120W load)
12V/7Ah x 1
12V/7Ah x 2
10 min.
30 min.
Typical Recharge Time
12V/9Ah x 2
40 min.
42 min.
4-6 hours recovery to 90%
Indicators
AC Mode
Battery Mode
Green LED on
Green LED Flashes
Fault
The right green LED is on and LED’s 2-5
indicate load level
Yellow LED Flashes
The right green LED flashes and LED’s 2-5
indicate battery capacity
Red LED Flashes
Protection
Full Protection
Overload, discharge and overcharge protection
Alarm
Battery Mode
Sounds every 10 seconds
Low Battery
Sounds every second
Overload
Sounds every 0.5 seconds
Battery Replacement Alarm
Sounds every 2 seconds
Fault
Continuously sounds
Physical
Dimension, D x W x H (mm)
Net Weight (kg)
287 x 100 x 142
350 x 146 x 160
4.25
8.0
230 x 500 x 280
11.1
Operating Environment
Humidity
Noise
0-90% RH @ 0-400C (non-condensing)
Less than 40dB
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
4
11.5
UPS - LINE INTERACTIVE
MODIFIED SINEWAVE
T1 SERIES (500VA-1kVA)
•Compact and stylish, ideal for office or home
•Excellent performance and reliability, designed for maximum equipment protection
•Advanced MCU control technology, enhancing UPS performance
•500VA, 700VA and 1kVA, powerful enough for desktop PC’s
•Conforms to all necessary safety and CE specifications
•No noise, place it on your desktop
•Simple, easy to read LCD display
•Fast, low voltage protection buck and boost
•Predicting mains failure
•Automatic voltage regulation saving battery power
•Low battery protection preventing deep discharge
•Advanced battery management
•Modem, phone line and peripheral equipment protection
•Hot battery swap, no need to switch off UPS (except for 1kVA).
Model
ST1005
Capacity
ST1007
500VA/300W
700VA/420W
ST1010
1000VA/600W
Input
Input Voltage Range
220/230/240VAC (+25% / -30%)
Input Frequency
44Hz ~ 56Hz
Output
Output Voltage
220/230/240VAC ± 10% (On Battery Mode)
Output Voltage Regulation
± 10%
Output Frequency (Battery Mode)
50 ± 0.1Hz
Overload Capability
Delayed protection when the output is > 150% overload
Battery
Number of Batteries
1 cell
Recharge Time to 90%
1 cell
2 cells
< 10 hours
Transfer time
AC to DC
< typical 6 ms
Indication
LCD
AC Mode, Battery Mode, Output Status, Battery Capacity, Overload, UPS Fault
Audible Alarm
Battery Mode
Long beeping
Low Battery
Continuous beeping
Overload
Short beeping
Dimensions
W x H x D (mm)
90 x 165 x 325
90 x 165 x 325
120 x 210 x 380
6.3
6.6
15
Weight
Net Weight w/ Battery (kgs)
Environmental
Operating Temperature
-5 ~ +400 C
Relative Humidity
Audible Noise
< 90% (Non-Condensing)
<45dBA @ 1 Meter
<50dBA @ 1 Meter
<55dBA @ 1 Meter
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
5
UPS - LINE INTERACTIVE
PURE SINEWAVE
T2 SERIES (1kVA-3kVA)
Launched in 2005 and superseding the highly regarded PHD IP Series UPS, the T2 Series benefits
from the latest microprocessor Control Unit (MCU) technology, and now offers even greater value for
money. The T2 is aimed at users that require protection from line voltage fluctuations and require a
reliable and constant power source. The T2 is a sophisticated unit utilizing full digital control technology.
Available with power rating of 1kVA, 2kVA and 3kVA each with LCD display and audible alarm keeping
you quickly updated on mains and battery status. The T2 is also fitted with an intelligent test button
enabling a self-test routine which also prevents the UPS from being inadvertently switched off.
FEATURES:
•Extensive log files
•Scheduled battery and inverter testing
•Scheduled system shutdown/restart
•User-Customisable commands and messages
•Multiple UPS control from a single computer
•Remote Console Command module for remote multiple server shutdown
•Internal SNMP sub-agent for integration into existing NMS (e.g. HP OpenView, CA).
Model
ST2010
ST2020
ST2030
1000VA/700W
2000VA/1400W
3000VA/2100W
Capacity
Maximum Capacity
Input
Input Voltage Range
220/230/240VAC ± 25% Singe Phase w/Ground
Input Frequency
44Hz ~ 56Hz
Output
Output Voltage
220/230/240VAC ± 2%
Output THD
< 3%
Efficiency (Battery Mode)
82%
Output Frequency (Battery Mode)
50 ± 0.1Hz
Overload Capability (Normal Mode)
Sustaining 5 min @ 100 – 200%; 3 sec @ > 200%
Overload Capability (Battery Mode)
Sustaining 30 sec @ > 100%; 1 sec @ 150%
Battery
Number of Batteries
2 cells
4 cells
6 cells
Recharge Time to 90%
< 8 hours (adjustable)
Charge Current of Long
Standby Model *
5A
Indication
LCD
AC Mode, Battery Mode, Output Status, Battery Capacity, Overload, UPS Fault
Audible Alarm
Battery Mode, Low Battery, Overload
Physical
Environmental
W x H x D (mm), Weight
Operating Temperature
Relative Humidity
Audible Noise
Communication Port
Long beeping, Continuous beeping, Short beeping
150 x 220 x 460, 19kg
220 x 330 x 487, 32kg
-5 ~400 C
220 x 330 x 487, 42kg
< 95% (Non-Condensing)
<45dBA @ 1 meter
Standard RS232; USB or SNMP/HTTP (optional)
* All T2 models have a long standby option with no built in batteries, this is the charge current of the long standby models.
For long standby models, add “-L“ to the part number.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations. Specification or design can be changed at anytime without prior notice.
6
UPS - LINE INTERACTIVE
PURE SINEWAVE
T2R SERIES (2kVA-10kVA)
FEATURES:
•True Bi-Lateral Converter Line-interactive UPS
•Pure Sinewave and suitable for linear and non-linear loads
•Rack and Tower Convertible
•Standard and long backup time models available
•Multi-Interface slot for RS232, SNMP, USB, RS485, Modbus,
Dry Contact and customised interfaces
•Various communication options selectable and all can be
available at the same time
•Complete protection for overload, overheat, surges, spikes,
short circuit and over charge
•Detachable two-way dialogue interactive dot-matrix LCD
control panel
•Real time remaining backup time calculations
•User friendly, swappable battery replacement design
•Built-in powerful charger with power factor correction
•Emergency Power Off (EPO) available
•Intelligent fan speed control
•Cold start (DC start) function
•Compatible with generators.
7
UPS - LINE INTERACTIVE
PURE SINEWAVE
Model
Capacity
ST2R20
ST2R30
ST2R50
ST2R75
ST2R100
2kVA/1250W
3kVA/1875W
5kVA/3125W
7.5kVA/4688W
10kVA/6250W
Input
Voltage
220/230/240VAC
Voltage Range
170VAC~300VAC
Frequency Range
45Hz~70Hz Auto-Sensing
Output
Voltage
220/230/240VAC ± 3% settable on the LCD
Frequency Range
50Hz or 60Hz ± 0.1Hz
Wave Form
Pure Sinewave
Efficiency (Line Mode / Battery Mode)
98% / 80%
Overload (Line Mode)
> 110% Buzzer alarms and Amber LED blinks continuously
Overload (Batt. Mode)
110%-150% for 30sec, > 150% for 200ms, then UPS shuts down
Battery
Battery Voltage
Battery Quantity
36Vdc
3 x 9Ah
48Vdc
6 x 7.2Ah
Charge Current of Long Standby Models **
8 x 9Ah
16 x 7.2Ah *
16 x 9Ah *
> 10A
N/A
Other
Transfer Time
< 4ms
Communication Interface
USB standard, RS232, RS485, SNMP, Dry Contact and AS400 available
Physical and Environmental
Operating Temperature
00C-400C
Relative Humidity
0-95% non-condensing
Audible Noise
Dimensions (W x H x D, mm)
< 55dBA (@ 1m)
440 x 88 x 465
440 x 132 x 465
440 x 132 x 620
Weight (kg)
24.5
36.9
49.8
IEC Outputs
6
10
10 + 1 Terminal
Block
440 x 132 x 465 (UPS),
440 x 132 x 465 (Battery Box)
34.6
(UPS only)
36.6
(UPS Only)
5 + 1 Terminal Block
Safety Standards
Safety
EN62040-1-1
EMC
EN62040-2
Marks
CE, UL, cUL
* Batteries on these models are external to the UPS cabinet
**Models from 2kVA - 7.5kVA have long standby models available, add “-L” to the model no. Charge currents on these of up
to 30A available on request.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
8
UPS - LINE INTERACTIVE
PURE SINEWAVE [Long Standby]
T2X SERIES (800W-8kW)
The Star T2X UPS is an All-In-One user friendly UPS, easy
to handle, suitable and compatible for almost all Home/Office
applications (Linear and non-linear loads including Air Conditioners!).
Being a line interactive UPS, it can produce clean and perfect
PURE SINEWAVES, by providing the best power quality for all
your electric equipment.
The traditional UPS supplies power only for a limited few minutes,
the T2X can function as an efficient GENERATOR! With an Auto
Transfer Switch, it can easily handle any critical power failure
situations.
Also, the T2X Series has a powerful charger that can supply a
capacity over 500 Ah, it can adapt itself and charge without any
damage to any type of battery. Its Solar Power Server allows the
UPS to work with solar panels to supplement the built in battery
charger of the UPS.
The Star T2X Series: an ecologic solution for homes and offices!
Features:
Powerful charger
Multiple microprocessor design base
Compatible with linear and non-linear load
Stronger charger to support batteries 500AH and up
24 hours operation on the inverter
Auto transfer switch
Parameter presentable
DC start and automatic self-diagnostic function
THD less than 3%
Pure sinewave
High efficiency design to save electricity
Low heat dissipation in long time operation
Designed to operate under harsh environment
LCD Panel Control
Sinewave inverter
Controllable & Removable panel with LCD
Wall Mounted Design or 19” Rack
Solar power server
9
UPS - LINE INTERACTIVE
PURE SINEWAVE [Long Standby]
A Positive DC connector
B Negative DC connector
C Cooling Fan
D AC Output Fuse
E AC Output Terminal Block
F Solar Panel Input.
Model
Capacity
Watt/Amps
Normal
Voltage
ST2010X
ST2020X
ST2040X
ST2060X
ST2080X
800W/3.6A
1600W/7.2A
2400W/10.9A
4000W/18.1A
6000W/27.2A
8000W/36.3A
Acceptable Voltage
220Vac
120-275Vac / 60-135Vac
120Vac-275Vac
50Hz / 60Hz (45Hz- 70Hz)
120Vac +-2% /60VAC +- 2%
120Vac+-2%
130Vac +-2% /65Vac +-2%
130Vac+-2%
Line High Transfer
275Vac +-2% / 135Vac +-2%
275Vac+-2%
Line High Return
260Vac+-2% / 130Vac +-2%
260Vac+-2%
220Vac (230V or 240 Vac re-settable via LCD panel);
110Vac (115V or 120Vac re-settable via LCD panel)
230Vac (220V
or 240Vac
re-settable via
LCD panel)
Line Low Return
Voltage
Range
220Vac / 110Vac
Frequency
Line Low Transfer
Input
Output
ST2008X
Voltage
Voltage Regulation (Batt Mode)
<3% RMS for entire battery voltage range
Frequency
50Hz or 60 Hz
Frequency Regulation (Batt Mode)
+-0.1 Hz
Power Factor
0.67
0.6
Waveform
Transfer
Time
Typical
Battery Voltage
Battery
Solar
Power
Display
LCD
< 8ms
12Vdc
24Vdc
Backup Time (at full load)
Max Charging Current (3 steps selectable )
>40A
>50A
Standard
UPS status,I/P &O/P Voltage Frequency, Load%, Battery Voltage & %, Temperature, Model
LED
Normal (Green), Warning (Yellow), Fault (Red)
Beeping every 4 seconds
Low Battery
Beeping every second
UPS Fault
Beeping Continuously
Overload
Beeping twice per second. UPS will shutdown automatically in 30 seconds if overload is over
105~ 150% and up to 150 % will shutdown immediately.
Operation Temperature
Environment
0-40 degree C; 32-104 degree F
Relative Humidity
0-95% non-condensing
Audible Noise
Net Weight (Kgs)
Physical
Less than 55dBA (at 1M)
23
49.2
51.4
53.6
Dimension (WxHxD)mm Rack Mount
440*132*290 440*132*360
14
21
440*132*360
N/A
N/A
N/A
Wall Mounted(W*H*D)mm
298*400*150 298*450*190
298*450*190
415*600*260
415*600*260
415*600*260
* Add “S“ to the part number for the solar server option
Different specifications required are available
All specifications mentioned above are subject to change without prior notice.
10
>60A
Optional*
Battery Mode
Audible
Alarm
48Vdc
Long time available
Solar Power Server 50A (Option)
LCD Extended LCD Remote Control (optional)
0.62
Pure Sinewave
UPS - ONLINE (TRANSFORMERLESS)
1 PHASE INPUT, 1 PHASE OUTPUT
T3 SERIES (1kVA-10kVA)
The T3 is a physically small On-Line double conversion UPS
but retains all the features normally associated with On-Line
technology, but what is On-Line double conversion technology
and why does it matter? Simply put “double conversion” is where
the mains supply is rectified to a clean DC voltage and rebuilt into
a very clean and regulated AC voltage, at all times your critical load
runs from this clean no break supply.
Line-Interactive and Off-Line UPS’s are single conversion, put in its
crudest form your computer runs on semi regulated mains and will
always suffer a small break in supply whilst the UPS moves from
mains mode to battery mode in a mains fail situation.
•TRUE ON-LINE DOUBLE TECHNOLOGY FOR
HIGH LEVEL OF PROTECTION
•DSP TECHNOLOGY (FOR 6-10kVA MODELS)
•PARALLEL REDUNDANCY CAPABILITY (FOR 6-10kVA MODELS AS STANDARD)
•INTEGRATED SMARTCARD SLOT PROVIDING A
CHOICE OF COMMUNICATIONS INTERFACES
•OPTIONAL SPECIALISED UPS MANAGEMENT SOFTWARE
•USER FRIENDLY LCD DISPLAY
•FAILSAFE INTERNAL BYPASS
•SWITCH WITH MANUAL CONTROL
•LONG RUNTIME AVAILABILITY.
PARALLEL
A big advantage offered by the T3 6kVA to 10kVA is that by means
of a simple cable the machines can be linked together to form a
parallel N+1 system. This offers the client the opportunity to be
either a fail safe system or the option to expand the power as the
network grows. Up to three machines can be connected in this way
making the T3 a flexible and versatile solution.
UPS MANAGEMENT SOFTWARE
The UPS management software is installed on a server or
workstation connected to each UPS via the serial or USB port.
Power failure, power restored, battery failure or eight events will
be detected and the user informed. A shutdown will be initiated
when the batteries are exhausted or a technical problem occurs
with the UPS. The UPS management software disconnects, logs
out users and closes open applications(subject to application/
operating system support) before shutting down the operating
system itself.
SIMPLE NETWORK MANAGEMENT
PROTOCOL (SNMP)
The T3 SNMP external agent can be located up to 5 metres away
from the UPS. Initial configuration is carried out by serial comms
using any suitable terminal application (e.g. Hyperterminal for
Windows).
The embedded HTTP server presents an HTML interface to the
network, which can be accessed from any web browser.
All system parameters can be configured from here including
scheduled shutdown. A sophisticated JAVA applet provides full
monitoring in real time, along with comprehensive events and
history logs.
11
UPS - ONLINE (TRANSFORMERLESS)
1 PHASE INPUT, 1 PHASE OUTPUT
Model
ST3010
ST3020
Topology
ST3030
ST3060
ST3100
6000VA/4800W
10000VA/8000W
True On-Line, Double Conversion
On-battery Waveform
Pure Sine Wave
Input
Maximum Capacity (VA/W)
1000VA/800W
2000VA/1600W
Nominal Input
Input Voltage Regulation
3000VA/2400W
230VAC
160~300 VAC Single Phase w/ Ground
Nominal Input Frequency
170~285 VAC Single Phase
w/Ground
50/60 ± 4Hz
Input PFC
≥0.95
≥0.98
Input Short Protection
Circuit Breaker
Output
Nominal Output
220/230/240 VAC nominal
Output Regulation
Output T.H.D
± 2%
≤3% (Linear Load)
≤6% (Non-Linear Load)
± 1%
≤4% THD (Linear Load)
≤7% THD (Non-Linear Load)
≤2% THD (Linear Load)
≤6% THD (Non-Linear Load)
High Efficiency Mode (AC to DC)
85%
85%
88%
> 88%
High Efficiency Mode (DC to AC)
83%
83%
83%
> 88%
Crest Factor
3:1
Start on Battery
Yes
Output Frequency
50 Hz ± 0.2 Hz
50 Hz ± 0.5 Hz
Battery
Typical Backup Time (at full load)
9 minutes
Battery Type
Number of Batteries
12 minutes
8 minutes
10 minutes
8 minutes
Sealed Lead-Acid maintenance-free 12VDC/7Ah per cell
3 cells
12VDC/9Ah per
cell
8 cells
Recharge Time to 90%
20 cells
5 hours
Charge Current of Long Standby
Model *
7 hours
8A
8 hours
4.2A **
Advanced Warning Diagnostics
Front Panel Indication – LCD
UPS Status, I/P Voltage & Frequency, O/P Voltage & Frequency,
Battery Voltage, Battery Capacity, Loading %, Temperature, History Alarm.
Front Panel Indication – LED
Normal (Green), Warning (Yellow), Fault (Red)
Audible Alarms
Battery Mode, Low Battery, Overload, Fault
Communication Interface
Communication Port
RS232 (Standard), DB9 or USB or AS400 or SNMP / HTTP (Optional)
Environmental
Audible Noise
< 45dBA @1 meter
< 50dBA @1 meter
< 55dBA @1 meter
Mechanical
Dimensions (W x H x D mm)
Weight (Net Weight with Battery) (kgs)
160 x 220 x 400
15
200 x 352 x 450
34
260 x 717 x 570
35
90
* All T3 models have a long standby option with no built in batteries, this is the charge current of the long standby models.
For long standby models, add “-L“ to the part number.
**6 and 10kVA models can have up to 25A charging capabilities when connected in parallel with the ST-CHARGER external
super charger.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
12
93
UPS - ONLINE (TRANSFORMER)
1 PHASE INPUT, 1 PHASE OUTPUT
T3T SERIES (10kVA - 15kVA)
The T3T is a transformer isolated On-Line double conversion UPS
but what is On-Line double conversion technology and why does it
matter? Simply put “double conversion” is where the mains supply
is rectified to a clean DC voltage and rebuilt into a very clean and
regulated AC voltage, at all times your critical load runs from this
clean no break supply and is isolated from the input.
Line-Interactive and Off-Line UPS’s are single conversion, put in its
crudest form your computer runs on semi regulated mains and will
always suffer a small break in supply whilst the UPS moves from
mains mode to battery mode in a mains fail situation.
PARALLEL
A big advantage offered by the T3T is that by means of a simple
cable the machines can be linked together to form a parallel N+1
system (only for 10kVA and 15kVA models). This offers the client
the opportunity to be either a fail safe system or the option to
expand the power as the network grows. Up to three machines
can be connected in this way making the T3T a flexible and
versatile solution.
UPS MANAGEMENT SOFTWARE
The UPS management software is installed on a server or
workstation connected to each UPS via the serial or USB port.
Power failure, power restored, battery failure or eight events will be
detected and the user informed. A shutdown will be initiated when
the batteries are exhausted or a technical problem occurs with
the UPS. The UPS management software disconnects, logs out
users and closes open applications(subject to application/operating
system support) before shutting down the operating system itself.
SIMPLE NETWORK MANAGEMENT
PROTOCOL (SNMP)
The T3T SNMP external agent can be located up to 5 metres away
from the UPS. Initial configuration is carried out by serial comms
using any suitable terminal application (e.g. Hyperterminal for
Windows).
The embedded HTTP server presents an HTML interface to
the network, which can be accessed from any web browser.
All system parameters can be configured from here including
scheduled shutdown. A sophisticated JAVA applet provides full
monitoring in real time, along with comprehensive events and
history logs.
•TRUE ON-LINE DOUBLE CONVERSION TECHNOLOGY
FOR HIGH LEVEL OF PROTECTION
•DSP TECHNOLOGY
•PARALLEL REDUNDANCY CAPABILITY (OPTIONAL)
•INTEGRATED SMARTCARD SLOT PROVIDING A CHOICE OF COMMUNICATIONS INTERFACES
•OPTIONAL SPECIALISED UPS MANAGEMENT SOFTWARE
•USER FRIENDLY LCD DISPLAY
•FAILSAFE INTERNAL BYPASS
•SWITCH WITH MANUAL CONTROL
•LONG RUNTIME AVAILABILITY.
1313
UPS - ONLINE (TRANSFORMER)
1 PHASE INPUT, 1 PHASE OUTPUT
Model*
ST3020T
Topology
ST3030T
ST3050T
ST3060T
ST3100T
ST3150T
True Online Double Conversion, Isolated Transformer Output
Input
Maximum Capacity (kVA/kW)
2/1.4
3/2.1
5/3.5
6/4.2
Input Voltage Regulation
220VAC ±25%
Nominal Input Frequency
50Hz ± 5%
Battery Voltage
48VDC
96VDC
10/7
15/10.5
192VDC
Output
Output Regulation
220VAC ± 2%
Waveform
Sinewave, ≤3% THD
Switch Time
0ms
Overload Capacity
125% for 60 seconds, 150% for 0.5 seconds
Crest Factor
3:1
Start on Battery
Yes
Output Frequency
Automatic synchronous tracing when power supply normal,
at 50Hz ± 0.5% when power supply abnormal
Battery
Back up time**
Battery efficiency
Charging***
15 mins
25 mins
10 mins
>80%
10 mins
Any backup time
>87%
>89%
Intellectual MMBM battery control technique, unique multi-charging mode improving
the reliability and lengthening the life of the batteries
Other Features
Panel Display
Input voltage, Output voltage, Load capacity, Battery voltage
LED indicating lights show the working status
Alarm
Mains supply abnormal, Low battery, Overload
Protection Function
Protection for low battery, overload, over temperature, short circuit,
output over voltage, output low voltage
Parallel function*
N/A
Random extending or N+1
redundancy parallel connection
Communication Interface
Communication Function
Remote Control (Optional)
RS232 communication port supports UPSilon 2000 software (standard).
Supports SNMP adapter for network management (optional).
Independent digital remote control at the distance of 1000 meters supported by RS485,
which supports remote monitoring
Dry connection
The port allows a 2A current, convenient and safe
Environmental
Audible Noise
< 55dBA @1 meter
< 60dBA @1 meter
Work Temperature,
Relative Humidity
0~400C, 0~95%(no condensation)
Altitude
Meet GB/T 7260.3-2003 standard
Mechanical
Dimensions (W x L x H mm)
Weight (with & without batteries) (kgs)
230 x 620 x
470
65/52
230 x 635 x 690
82/58
90/57
400 x 800 x 1180
108/61
210/92
250/140
* T3T10kVA and 15kVA models have a parallel redundant option, add “-P“ to the part number.
**T3T 2kVA-15kVA models have a long standby option with no built in batteries, add “L“ to the part number for these models.
***5-15kVA models can have up to 15A charging capabilities when connected in parallel with the ST-CHARGER external super charger.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
14
UPS - ONLINE (TRANSFORMERLESS)
1 PHASE INPUT, 1 PHASE OUTPUT
T3R SERIES (1kVA-10kVA)
With ever greater demands being made on valuable floor space,
many IT managers are moving towards computer rack solutions
rather than conventional floor standing options offered in the past.
The same philosophy has affected the UPS industry with many
UPS now being located with the computer inside the rack cabinet.
On-Line UPS have historically been handicapped in this particular
market sector, essentially for two reasons, size and price.
Most IT managers have dealt with this problem by moving to
Line-Interactive and Off-Line topologies. As these technologies
have fewer fail safe features and for the most part only work when
a problem occurs. With the introduction of the T3R series these
past limitations are no longer valid.
•EXTENSIVE LOG FILES
•SCHEDULED BATTERY AND INVERTER TESTING
•SCHEDULED SYSTEM SHUTDOWN/RESTART
•USER-CUSTOMISABLE COMMANDS AND MESSAGES
•MULTIPLE UPS CONTROL FROM A SINGLE COMPUTER
•REMOTE CONSOLE COMMAND MODULE FOR REMOTE MULTIPLE SERVER SHUTDOWN
•INTERNAL SNMP SUB-AGENT FOR INTEGRATION INTO EXISTING NMS (E.G. HP OPENVIEW, CA UNICENTER.
The T3R is a physically small On-Line double conversion UPS
but retains all the features normally associated with On-Line
technology, but what is On-Line double conversion technology and
why does it matter? Simply put, “double conversion” is where the
mains supply is rectified to a clean DC voltage and rebuilt into a
very clean and regulated AC voltage, at all times your critical load
runs from this clean no break supply. Line-Interactive and Off-Line
UPS are single conversion, put in its crudest form, your computer
runs on semi regulated mains and will always suffer a small break
in supply whilst the UPS moves from mains mode to battery mode
in a mains fail situation. The T3R offers a competitive price, even
against the more basic technologies, but unlike these technologies
you will get as standard an LCD screen, RS232, USB port options,
battery extension options, battery monitoring, no-break supply,
static switch, wide voltage input without using batteries, optional
software, comms slot for SNMP, Relays or Optocoupler.
SIMPLE NETWORK MANAGEMENT PROTOCOL (SNMP)
The T3R SNMP external agent can be located up to 5 metres
away from the UPS. Initial configuration is carried out by serial
comms using any suitable terminal application (e.g. Hyperterminal
for Windows). The embedded HTTP server presents an HTML
interface to the network, which can be accessed from any web
browser. All system parameters can be configured from here
including scheduled shutdown. A sophisticated JAVA applet
provides full monitoring in real time, along with comprehensive
events and history logs.
UPS MANAGEMENT SOFTWARE
The UPS management software is installed on a server or
workstation connected to each UPS via the serial or USB port.
Power failure, power restored, battery failure or eight events will
be detected and the user informed. A shutdown will be initiated
when the batteries are exhausted or a technical problem occurs
with the UPS. The UPS management software disconnects, logs
out users and closes open applications(subjet to app/os support)
before shutting down the operating system itself.
15
15
UPS - ONLINE (TRANSFORMERLESS)
1 PHASE INPUT, 1 PHASE OUTPUT
Model
ST3R10
ST3R20
Topology
ST3R30
ST3R60
ST3R100
True On-Line, Double Conversion
Output Waveform
Pure Sine Wave
Input
Maximum Capacity (VA/W)**
1000VA/800W
2000VA/1600W
Nominal Input Voltage
Input Regulation Voltage
3000VA/2400W
6000VA/4800W
10000VA/8kW
230 VAC
160~300 VAC Single Phase w/ Ground
Nominal Input Frequency
160~300 VAC Single Phase
w/ Ground
50/60 ± 4Hz
Input PFC
≥0.95
≥0.98
Input Short Protection
Circuit Breaker
Output
Nominal Output Voltage
220/230/240 VAC nominal
Output Voltage Regulation
Output T.H.D
± 2%
≤3% (Linear Load)
≤6% (Non-Linear Load)
≤4% THD (Linear Load)
≤7% THD (Non-Linear Load)
≤2% THD (Linear Load)
≤6% THD (Non-Linear Load)
High Efficiency Mode (AC to DC)
85%
85%
88%
> 88%
High Efficiency Mode (DC to AC)
83%
83%
83%
> 88%
Crest Factor
3:1
Start on Battery
Yes
Output Frequency
50 Hz ± 0.2 Hz
50 Hz ± 0.5 Hz
Battery
Typical Backup Time
Battery Type
Number of Batteries
9 minutes
12 minutes
8 minutes
10 minuts
Sealed Lead-Acid maintenance-free 12VDC/7Ah per cell
3 cells
Recharge Time to 90%
12VDC/9Ah per cell
8 cells
20 cells
5 hours
Charge Current of Long Standby Model *
8 minutes
7 hours
8A
8 hours
4.2A **
Advanced Diagnostics
Front Panel Indication – LCD
UPS Status, I/P Voltage & Frequency, O/P Voltage & Frequency,
Battery Voltage, Battery Capacity, Loading %, Temperature, History Alarm.
Front Panel Indication – LED
Normal (Green), Warning (Yellow), Fault (Red)
Audible Alarms
Battery Mode, Low Battery, Overload, Fault
Communication Interface
Communication Port
RS232 (Standard), DB9 or USB or AS400 or SNMP / HTTP (Optional)
Environmental
Operation Temperature
0-400 C
Storage Temperature
-150C to 500C
Relative Humidity
Audible Noise
20% to 90% non-condensing
< 45 dBA @ 1 meter
< 50 dBA @ 1 meter
< 55 dBA @ 1 meter
440 x 88 x 465
(with internal batteries)
440 x 88 x 465 (UPS only)
440 x 88 x 465 (External Battery)
440 x 132 x 640 (UPS Only)
440 x 132 x 640 (External Battery)
Mechanical
Dimensions (W x H x D mm)
Weight (Net Weight with Batteries) (kgs)
15.5
35
36
85
88
* All T3R models have a long standby option with no built in batteries, this is the charge current of the long standby models.
For long standby models, add “-L“ to the part number.
**6 and 10kVA models can have up to 25A charging capabilities when connected in parallel with the ST-CHARGER external super charger.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
16
16
UPS - ONLINE (TRANSFORMERLESS)
1 PHASE INPUT, 1 PHASE OUTPUT
FP SERIES (1kVA-6kVA)
The FP series UPS is a true on-line double conversion UPS
offering rack and tower placements. It is a reliable and effective
system to protect critical systems from power outages and sags.
The FP series is designed for optimising power quality with
the ease of installation.
APPLICATIONS
•Computers
•Network Servers
•Workstations
•Wireless Communications
•Other Electronic Peripherals.
FEATURES:
•TRUE ON-LINE DOUBLE CONVERSION TECHNOLOGY FOR HIGH LEVEL OF PROTECTION
•CONTINUOUS BATTERY CHARGER AND INVERTER
FOR PRIMARY POWER PATH
•CONSTANT BATTERY CONNECTION TO INVERTER
AND LOAD
•GUARANTEES FULL POWER OPERATION DURING POWER FAILURE
•NO VOLTAGE DROP AND ZERO TRANSFER TIME
•LIGHT WEIGHT UNIT
•HOT-SWAPPABLE BATTERY
•USER-FRIENDLY GRAPHIC LCD DISPLAY
•FLEXIBLE MOUNTING ORIENTATION
•ROTATABLE LCD DISPLAY FOR TOWER OR 19”
RACK CONCEPT
•USER REMOTE INTERFACE/CRUISER.
•Flexible Mounting Orientation: Allows system integrators more flexibility in designing their backup power system to maximize space. With the rotatable LCD design, installers can mount the UPS vertically or horizontally.
•User-Friendly Graphic LCD: This robust LCD display enables field service engineers to easily troubleshoot the UPS without opening the box, thus reducing downtime.
•Single Voltage Battery Pack Design: A 48VDC standard battery pack design comprised of 4 x 12V7AH is used in all FP series UPS models and is interchangeable with each other.
•Hot-Swappable Battery: The standard 48VDC battery pack allows installers to take the headache out of battery installation.
Installers can now simply slide the used battery pack out of the unit and replace it with a new pack. All FP battery packs are interchangeable reducing the risk of system failures.
•Light Weight Design: The FP model is specifically designed for field installation. The light weight design requires only a single installer to put the system in place. This will significantly reduce on-the-job injuries and installation fees.
•User-Remote Interface / Cruiser: The off-site user can now test, set parameters, monitor power status, save file, and shutdown the system all via remote inerface. The user-remote interface includes SNMP/HTTP Card, RS232, USB, DB9, and AS400 interface.
STANDARD ACCESSORIES
•Mounting Feet: Two (2) mounting feet for tower configuration are supplied with the FP Series UPS 1KVA to 1.6KVA.
All other models 2.2KVA to 3.2KVA are self supporting.
•Racking Ears: Standard 19” rack mounting ears are available
for all FP Series UPS models.
17
17
UPS - ONLINE (TRANSFORMERLESS)
1 PHASE INPUT, 1 PHASE OUTPUT
Model
FP1600
FP2500
Topology
On-battery Waveform
FP3200
FP6000
True On-Line, Double Conversion
Pure Sine Wave
Input
Maximum Capacity (VA/W)
1600VA / 1120W
2500VA / 1750W
Nominal Input (Voltage Regulation) *
3200VA / 2240W
6000VA / 4200W
230VAC (160VAC-276VAC)
Nominal Input Frequency
50/60 ± 5Hz
Input PFC
> 0.98 @ Full Load
Input Short Protection
Circuit Breaker
Output
Nominal Output (Voltage Regulation)
208/220/230/240 VAC nominal (Rated Voltage ± 2%)
Output T.H.D
< 3% @ Linear Load
High Efficiency Mode (AC to AC)
> 88%
Crest Factor
Output Frequency
Overload Capability
90%
3:1
50 / 60Hz (Autotracking)
Sustaining 50sec @ 108% Load; 28sec @ 110-120% Load; 15sec @ 120-130% Load; 9sec
@ 140-145% Load; Immediate Response @ 150% Load
Battery (Extendible in 2U High Modules) **
User Replaceable Battery
Typical Backup Time (Full / Half Load)
48V (1 x 48VDC
Battery Pack)
96V (2 x 48VDC
Battery Pack)
96V (2 x 48VDC
Battery Pack)
96V (2 x 48VDC Battery
Pack)
7 / 18 min
8 / 20 min
6 / 17 min
4 / 10 min
Battery Type
Sealed VRLA 12V7Ah; Hot Swap
Recharge Time to 90%
8 hours
4 hours
Advanced Warning Diagnostics
Front Panel Indication
Front panel menu driven LCD monitoring and control panel for all functions
Audible Alarms
DC Mode, Low battery, Voltage / Frequency Error, Charger Fail, High Temp,
Overload, Fault, PFC Overload
Communication Interface
Communication Port
RS232 (Standard), DB9 or USB or AS400 or SNMP / HTTP (Optional), SNMP (Optional)
Environmental
Operation Temperature
0 ~ +400 C
Storage Temperature
-15 ~ +500 C
Relative Humidity
0% - 95% non-condensing
Audible Noise
< 45dBA @ 1 meter from surface of the unit
Mechanical
Dimensions (W x H x D mm) - Rack Position
Weight (UPS / Battery Packs)
426 x 88 x 500
426 x 176 x 500
426 x 88 x 500
426 x 176 x 500
12kg / 11.2kg
13.2kg / 31.2kg
13.4 / 31.4kg
16kg / 31.4kg
Conformance
EMI / RFI Compatibility
Safety Certifications
EN50091-2 Class B, EN55022B
CE, TUV / GS
* 10V systems available on request
**Each battery module comprises 2 x 48VDC battery packs in a 2U box.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
18
UPS - ONLINE (TRANSFORMERLESS)
3 PHASE INPUT, 1 PHASE OUTPUT
T4 SERIES (10kVA-20kVA)
The T4 is a physically small On-Line UPS but retains all the
features normally associated with double conversion technology.
Simply put "double-conversion" is where the mains supply is
rectified to a DC voltage and rebuilt into a very clean and
regulated AC voltage, at all times your critical load runs
from this clean no break supply.
Parallel
A big advantage offered by the T4 10kVA to 20kVA is that by means
of a simple cable the machines can be linked together to form a
parallel N+1 system. This offers the client the opportunity to either
have a fail safe system or the option to expand the power as the
network grows. Up to three machines can be connected in this way
making the T4 a flexible and versatile solution.
ULTRA COMPACT
•TRUE ON-LINE DOUBLE CONVERSION TECHNOLOGY FOR ULTIMATE POWER PROTECTION
•DSP TECHNOLOGY
•PARALLEL REDUNDANCY CAPABILITY AS STANDARD
•IGBT INVERTER TECHNOLOGY
•SNMP/HTTP OPTION FOR REMOTE MANAGEMENT & INTEGRATION INTO NMS
•SMART RS232 AS STANDARD
•INTEGRATED SMARTCARD SLOT PROVIDING A CHOICE OF COMMUNICATIONS INTERFACES
•OPTIONAL SPECIALISED UPS MANGEMENT SOFTWARE
•USER FRIENDLY LCD DISPLAY
•FAILSAFE INTERNAL BYPASS SWITCH WITH MANUAL CONTROL
•LONG RUNTIME AVAILABILITY.
With a very small footprint you will find a ready home for the T4 in
even the most hard-pressed data center. Installing such a compact
free-standing UPS avoids taking up valuable rack space without
significantly reducing the available floor area.
DISPLAY PANEL
LCD display and audible alarms actively let you know if the unit
is on battery, the battery charge is low, or there is an overload
condition. Loading and battery information via the LCD prevent
you from exceeding the UPS capacity and allow you to assess
the remaining runtime before battery reserves are depleted.
ADVANCED BATTERY MANAGEMENT
A variable boost charger ensures quick battery recharge.
This means that the T4 UPS is fully prepared for duty with a
minimum recovery time in the event of a power failure.
Active battery management intelligently monitors the battery
set with automatic battery and circuitry self-tests, this feature
increases both battery life and system reliability.
UPS MANAGEMENT
One standard management tool can be used to monitor and
control all your UPS’s from one central location. This means power
management can now be integrated into your existing network or
building management strategy. Alarms (‘traps’) can be configured
to ensure automatic notification of events such as low battery,
mains failure or overload. Two such tools can be used with the
T4: Simple Network Management Protocol (SNMP) and UPS
Management Software via RS232.
19
19
UPS - ONLINE (TRANSFORMERLESS)
3 PHASE INPUT, 1 PHASE OUTPUT
Model
ST4100
ST4150
Topology
ST4200
True On-Line, Double Conversion
On-battery Waveform
Pure Sine Wave
Input
Maximum Capacity (kVA/kW)
10kVA/8kW
15kVA/12kW
Nominal Input Voltage
20kVA/16kW
380VAC Three Phase (3 Φ 4W + G)
Input Voltage Regulation
304 ~ 478 VAC
Nominal Input Frequency
50/60 ± 4Hz
Input PFC
Input Short Protection
≥0.95 @ full load
50A Circuit Breaker
100A Circuit Breaker
Output
Nominal Output Voltage
220/230/240 VAC Single Phase (1 Φ 2W + G)
Output Voltage Regulation
± 1%
Output T.H.D
≤2% THD (Linear Load), ≤6% THD(Non-Linear Load)
Efficiency – Normal Mode
88%
Efficiency – Battery Mode
88%
Crest Factor
3:1
Start on Battery
Yes
Overload Capability (Normal Mode)
Sustaining 10 min @ 105% ~ 130% load; 1sec @ > 130% load
Overload Capability (Battery Mode)
Shut down UPS after 10 sec @ > 150% load
Output Frequency
50/60 Hz ± 0.05 Hz (Battery Mode)
Battery
Battery Type
Sealed Lead-Acid maintenance-free 12VDC/7Ah per cell
Number of Batteries
40 cells
40 cells
40 cells
Typical Backup Time at Full Load
12 mins
8 mins
6 mins
Recharge Time to 90%
< 8 hours
Charger Current (Max)
4.2A *
Advanced Diagnostics
Front Panel
Indication – LCD
UPS Status, I/P Voltage & Frequency, O/P Voltage & Frequency,
Battery Voltage, Battery Capacity, Loading %, Temperature, History Alarm.
Front Panel Indication – LED
Normal (Green), Warning (Yellow), Fault (Red)
Audible Alarms
Battery Mode, Low Battery, Overload, Fault
Communication Interface
Communication Port
RS232 (Standard), DB9 or USB or AS400 or SNMP / HTTP (Optional)
Environmental
Audible Noise
< 55dBA @ 1 meter
Mechanical
UPS Dimensions (W x H x D mm)
260 x 717 x 570
Battery Cabinet Dimensions
(W x H x D mm)
260 x 717 x 570
UPS Weight (kgs)
39
55
55
Battery Cabinet (w/battery) (kgs)
143
143
143
Total Weight (kgs)
182
198
198
*
20
All T4 models can have up to 25A charging capabilities when connected in parallel with the ST-CHARGER external
super charger.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
UPS - ONLINE (TRANSFORMERLESS)
3 PHASE INPUT, 1 PHASE OUTPUT
T4T SERIES (10kVA-50kVA)
The T4T Series UPS is an online sine wave UPS mainly designed
for major equipment used in large-scaled data centers (such as
measurement equipment, industrial automation equipment, etc.)
with high performance. Its high reliability provides necessary
protection on load for the users in finance, communication, traffic,
tax, forces, security, power source, education, government and
enterprise etc. The T4T Series UPS is true double conversion
on-line UPS. With IGBT power units, SPWM inverter, intellectual
multi modes battery management technique, advanced tech
and power management software.
TRUE ONLINE DOUBLE CONVERSION UPS
Output is fully isolated by a transformer, with IGBT power units
used to solve problems on the electric system such as lightning
strikes, power blackouts, etc.
EMC COMPLIANT
All products are EMC compliant. Testing points include conducting
disturbance, radiant disturbance, conducting ant-disturbance,
radiant ant-disturbance, power fault, mass pules, ESD etc.
Excellent EMC features make the T-UK Series capable of high
frequency communication and video & audio broadcasting.
COLD START FUNCTION
Because of special current limiting circuits on the UPS, the user
can start the UPS directly on its battery bank without mains being
available. The UPS has a more powerful cold starting capability
and is able to run on full load.
INTELLIGENT BATTERY MANAGEMENT TECHNOLOGY
Equipped with patented intellectual battery management
technique. With proffessional management design on battery
charging or discharging, the user can get high battery reliability
and running life. At the same time the intellectual charging
module can select the right charging power according to
different battery configurations making sure that there is
rapid power compensation on the battery bank.
FLEXIBLE NETWORK SUPERVISION
Flexible network supervising ability to realise intellectual
monitoring of the UPS. Including close point-to-point
communication supervising, middle range communication
supervising, and remote network management. Based on
these, there are many UPS functions such as real time
supervising over running status and features, automatic call,
sending e-mail, cell phone text messaging, voice function,
remote on/off for the UPS etc.
CURRENT EQUALISATION CONTROL TECHNIQUE
Current equalisation control technique, for N units parallel
redundancy or N+1 redundant parallel connection, digitized
current equalisation control, reliability and redundancy of the
system is higher than traditional parallel systems and field
installation and debugging is simple. UPS unit can be switched
on or be on line on standby mode, to enable hot maintenance
on line of parallel system.
PERFECT PROTECTION MEASURES
Protection for over output voltage and current, low battery,
quick current limit and short-circuit to avoid stoppages caused
by the user’s incorrect operation.
21
UPS - ONLINE (TRANSFORMER)
3 PHASE INPUT, 1 PHASE OUTPUT
Model
ST4100T
ST4150T
ST4200T
ST4300T
ST4400T
ST4500T
Input
Voltage Range
400VAC (-25%~+25%)
Frequency Range
50Hz / 60Hz ± 5%
Phase
Battery Voltage
Three phases, five wires
16 x 12Vdc = 192Vdc
29 × 12Vdc = 348Vdc
Output
Rated Power - kVA/kW
10/7
15/10.5
20/16
Voltage Range
30/24
40/32
50/40
230VAC ± 2%
Frequency
50Hz ± 1%(battery mode)
Waveform
THD ≤ 3%(linear load)
Battery Efficiency
≥ 90% (100% linear load)
Overload Capacity
10min at 105%, 1min at 125%, 0.5s at 150%
Crest Factor
3:1
Parallel Equal Current
≤ 5%(only applicable to the parallel models)
Other
Parallel Function
LCD Display
Random extending or N+1 redundancy parallel connection (only applicable to the parallel models)
Input voltage, Output voltage,
Load capacity, Battery voltage
LED Display
Alarm Function
Operation status
Mains supply abnormal,
Low battery, Overload
Communication Function
Low battery, Overload, Overheat, Output short circuit, Output over voltage
Audible Noise
< 60dBA @ 1m
Working Temperature,
Relative Humidity
Weight (kg)
Overload, AC input abnormal,
Low battery, Failure, Over-temperature
RS232/RS485, dry connection communication signal
Protection Function
Dimension (W x D x H) (mm)
Input voltage, Frequency, Output voltage, Battery voltage,
Load, DC current etc.
00C-400C, 0-95% (no condensation)
740 x 300 x 100
135
800 x 400 x 1180
160
205
225
280
305
10-15kVA models can have up to 15A charging capabilities when connected in parallel with the ST-CHARGER external super charger.
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
22
UPS - ONLINE (TRANSFORMER)
3 PHASE INPUT, 3 PHASE OUTPUT
T5 SERIES (10kVA-400kVA)
ST5 (10kVA-400kVA) features true on line double conversion
and zero sec. transfer time. Intellectual blocking design, adopts
advanced power apparatus IGBT, predominantly a SPWM
inverter. It also features MMBM intellectual multi-modes battery
management and intellectual monitoring and management
software. The parallel capacity can extend the on line parallel
redundancy or N+1 for upgradeability.
TRUE ONLINE DOUBLE CONVERSION
Output is isolated by a transformer, with IGBT power units used,
making sure a safe working environment for all equipment.
Isolation between N and G, and anti-impact from all kinds
of surgres and disturbances in power.
3 output phases can be adjusted independently, thus allowing
3 phase 100% unbalanced load, flexible load capacity and high
system reliability. Especially fit for computer rooms, communication etc.
RELIABLE EMC FEATURES
All products have passed the EMC tests. Testing includes
conducting disturbance, radiant disturbance, conducting
anti-disturbance, radiant anti-disturbance, power fault, mass
pulse, surge, ESD etc. Excellent EMC features allow the ST5
series to be capable of high frequency communication and video
& audio broadcasting.
COLD START FUNCTION
Due to a special current limiting circuit on the UPS, the user
can start the UPS directly from the battery bank connected for
emergency stituations in a no mains situation. The UPS can run
on cold start on full load.
FULL FUNCTION LCD DISPLAY
All ST5 series products above 20KVA are equipped with large LCD
Displays. They also feature real time surveillance on UPS running
parameters and status, FE and daily maintenance.
The ST5 features an Intelligent battery management system while
batteries are being charged and discharged for longer operational
life and higher reliability of the batteries.
FLEXIBLE NET PROJECT MONITORING (OPTIONAL)
Independent digital remote control, supported by RS485,
with a range of 1000 meters or SNMP network adapter
ADVANCED NON-MASTER-SLAVE SELF-ADAPTIVE CONTROL TECHNOLOGY (PARALLEL TYPE)
ST5 series parallel UPS features a powerful parallel capacity.
There is no need to set the parallel units. The User can extend
the parallel capacity as needed for N+1 parallel redundancy.
This increases the reliability of the power system.
23
23
UPS - ONLINE (TRANSFORMER)
3 PHASE INPUT, 3 PHASE OUTPUT
Model
ST5
010
ST5
020
ST5
030
ST5
040
ST5
050
ST5
060
ST5
080
ST5
100
ST5
120
ST5
160
ST5
200
ST5
300
ST5
400
Input
Voltage *
380/400VAC ± 25%
Rectifier Frequency
Range
40Hz~65Hz
SYNC Frequency
Tracking Range
50Hz ± 5% (± 10% option)
Phase
3φ4W+PE
Battery
12Vdc × 29 = 348Vdc / 12vDC x 30 = 360Vdc
Charge Current (Max)
5~40A (adjustable)
5~80A (adjustable)
Charge DC Voltage
Regulation
395V ± 5Vdc
DC Ripple Voltage
<1%
Output
Capacity (kVA)
10
20
30
40
50
60
80
Power Factor
100
120
160
200
300
400
0.8
Phase
3φ4W+PE
Voltage *
L-N: 220VAC ±1%, L-L: 380VAC ± 1%
Frequency
Utility normal, follow in phase automatically, Utility fault, output frequency at 50Hz ± 0.2%
Parallel mode
(optional)
None-principle-subordinate Adaptive Control Technique, User can extend parallel capacity as needed
for N+1 parallel redundancy
3 phase 100% load
unbalance voltage
stability
≤2%, allows 100% unbalance
Waveform
Sinewave THD ≤ 3% (linear load)
Crest Factor
3:1
Efficiency
90%
Static Bypass
Transfer Time
0ms
Overload Capacity
110% load for 30 min,125% load for 10 min,150% load for 1min
Regulation no load to
full load steady state
±2%
Other
Panel Display
LCD Display indicates 3 phase input voltage, input frequency, 3 phase output voltage, load, battery voltage,
battery charging and discharging etc. LED indicates running status
Battery Self-Testing
Automatically sounds an alarm and estimates battery status in battery abnormal status
Lightning Protection
Complies with IEC 1312
Operating Temp.,
Humidity
Dimension
(W x D x H) (mm)
Weight (kg)
00C-400C, 95% (non-condensing)
500 x 800 x 1180
185
205
235
800 x 800 x 1600
430
450
470
1000 x 800 x 1800
680
705
745
1800 x
1000 x
2000
805
1400
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
24
2200 x 1000
x 2000
2350
2380
UPS - ONLINE (TRANSFORMER)
3 PHASE INPUT, 3 PHASE OUTPUT
T6 SERIES 10kVA-1MVA
The AEC Star T6 series UPS is an on-lne double conversion
three phase UPS with a fully digitised intelligent galvanic isolation
design. Single unit ratings of up to 1MVA are available and parallel
capability is also available. The UPS can also be cusomised
for various input voltages allowing them to be used in various
applications (e.g. mining).
FEATURES AND ADVANTAGES:
Advanced Technology DSP, IGBT and Switching Components
To increase reliability and efficiency.
True Galvanic Isolation Design
An isolation transformer is used on the output. This can solve
numerous problems such as poor input grounding, different grounds
between input and output and ground leakage currents. The user
also has the benefit of attenuation of common mode noise from the
output isolation transformer.
Multi-CPU design and Software/Hardware Cooperate Control
Several CPU’s are employed in the control circuitry, critical
functions are designed to employ parallel redundancy to improve
reliability.
Redundant Power Supply
An extra power supply is connected redundantly to supply power
to the static switch, so that, there will be AC ouput no matter what
happens to the UPS.
Plug and Play Modular Design
The power circuit is seperated into several modules plugged
into slots in the UPS, which is easy to remove, allowing for quick
maintenance and easier trouble-shooting.
Each Phase with Individual Inverter Support
Allowing for 100% unblanced load.
Protection Against Detached or Floating Neutral of the Input
MOV’s are used at the input and provide sufficient protection to
both the UPS and the load from any lightning or surges casued
by neighbouring large loads.
Large Charging Power (Selectable)
The charge power is selectable according to the Ah of the
battery bank. Ah ratings to allow for 8 hours backup time can
be supported with no additional external chargers needed.
Various Interface Options
Remote control panel, 3 phase software for PC monitoring, auto
dialling module, battery monitoring module, 3 Phase SNMP card,
emergency stop switch.
12-Pulse Fully Controlled Rectifier (Optional)
In order to further improve the power factor and reduce harmonic
current drawn by the rectifier, the UPS from 120kVA uses a
12-pulse fully controlled rectifier. The total harmonic current
can be reduced to around 10% and the power factor improved
to over 0.8. A phase shift transformer is added to achieve the
performance. The input inductor is retained to obtain the best
result. This is a more rugged topology.
Parallel Operation (Optional)
To increase the capacity and reliability of the UPS.
The load is equally shared between the paralleled units.
When there is a fault with one of the units, the other units
continue running without output interruption.
FEATURES:
•Wide input range, robust design for harsh environments
•DC start function, can be started without AC
•Intelligent, safe and unique battery management system
•Variety of accessories
•Parallel operation available
•Specifications can be customised
•Frequency converter option available.
25
25
UPS - ONLINE (TRANSFORMER)
3 PHASE INPUT, 3 PHASE OUTPUT
Model
kVA
ST6
010
ST6
015
ST6
020
ST6
030
ST6
040
ST6
050
ST6
060
ST6
080
ST6
100
ST6
120
ST6
160
ST6
240
ST6
320
ST6
400
10
15
20
30
40
50
60
80
100
120
160
240
320
400
160
200
17.4
21.7
Input (Rectifier)
Input Voltage
190V / 208V / 380V / 400V / 415V / 440V / 480V / 600V, 3P4W or 3P3W
Input Range
± 20% (> 20% available on request)
Input Frequency
50Hz / 60Hz ± 5Hz
Power Walk In
0% - 100% : 20sec
Battery
DC Voltage
Maximum Charge Current
29 x 12Vdc = 348Vdc
5
8
10
15
20
25
30
40
50
60
80
120
Inverter
Output Voltage
Regulation
190V / 208V / 380V / 400V / 415V / 440V / 480V / 600V, 3P4W or 3P3W ± 1%
Output Power Factor
0.8
Output Frequency
50Hz / 60Hz ± 3Hz (lock range), 50Hz / 60Hz ± 0.1Hz (free running)
Phase Shift
< 0.50 at 100% unbalanced load
THD (Linear Load)
< 2%
Overload
< 110% Continuous, 110%-125% 15mins, 125%-150% 10mins, > 150% 30sec
Efficiency at 100% Load
93%
93.5%
94%
94.5%
95%
92.5
93
Overall Characteristics
Overall Efficiency
91
Maximum Heat
Dissipation (kW)
1.1
1.3
Dimensions
(L x W x H) (mm)
Weight (kg)
91.5
1.9
2.6
92
3
3.5
4.6
550 x 800 x 1600
270
300
Audible Noise
Temperature / Humidity
350
400
480
FCC Class A,
EN50091-1, -2
Short Circuit Protection
Lightning / EMC Filter
Galvanic Isolation
Indicator & Alarm
Remote Control /
Communication Interface
6.5
8.7
13
1100 x 800 x 1600
550
680
820
950
< 65dBA (at 1m)
1180
2200 x 800 x
1600
1450
1950
< 67dBA (at 1m)
00C-400C, 320F-1040F / 0-90% (Non-condensing)
Altitude
12 Pulse Rectifier
5.4
< 1500m above sea level
Optional
Standard
Yes
Rectifier, Reserve and Bypass
MOV / Input & Output
Output true Galvanic Isoation (input available on request)
LCD, LED, Mimic Display, Buzzer
Monitoring 1-99 UPS simultaneously / Dry Contact, RS232, RS485
Bigger sizes up to 1000kVA available
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
26
2450
3300 x
800 x
1600
3100
UPS - ONLINE (TRANSFORMER)
3 PHASE INPUT, 3 PHASE OUTPUT
T2000 SERIES (20kVA-600kVA)
TIME TO PROTECT
With many thousands of units sold, the PHD T2000 series UPS
is now legendary. Chosen by major enterprises around the world
for its reliability and performance, words simply can’t explain its
phenomenal success. But we don’t rest on our laurels, the T2000
has been modified and updated and now offers even greater
performance. With a Mean Time Before Failure of power to the
load in excess of 20 years the T2000 is even better value for
money. And with power ratings from 50kVA to 600kVA and higher,
the T2000 is engineered to offer power protection sufficient
to support a whole building if required. And as your power
requirements grow, more T2000 units can be added, offering
superb flexibility.
In addition to providing sufficient run-time to save files and
shutdown operating systems, autonomies of up to 8 hours are
available allowing you the option to complete a day’s work
without disturbance to your equipment, even during a power cut!
EXPANDABLE TO PROTECT
For genuinely redundant power protection, UPS can be installed
in either active parallel or hot standby mode, ready to take
over the load automatically in the event of a critical component
failure. The T2000 can be configured to function in either active
parallel or hot standby mode, with up to 6 units in the array.
In active parallel mode, the load is balanced across all the
configured units, ensuring that no single member of the array is
overstressed. If a unit needs to be shutdown for maintenance or
repair, the remaining units in the array will rebalance the load and
continue to provide uninterrupted protection. It is even possible to
remove a unit from the array during an outage without affecting
the load while the remaining units retain sufficient battery runtime.
In hot-standby mode, one or more units support the load, while
the remaining members of the array functions as standby unit.
The standby unit is continually on-line, but only takes over the
load when one of the primary units is no longer active.
This means that there is no break when power is transferred,
and the load continues to be supported without disturbance.
UPS MANAGEMENT SOFTWARE
The UPS management software is installed on a server
or workstation connected to each UPS via the serial port.
Power failure, power restored, battery failure or eight events
will be detected and the user informed. A shutdown will be
initiated when the batteries are exhausted or a technical
problem occurswith the UPS. The UPS management software
disconnects network connections, logs out users and closes
open applications (subject to app/os support) before shutting
down the operating system itself.
SIMPLE NETWORK MANAGEMENT PROTOCOL (SNMP)
The T2000 SNMP external agent can be located up to 5
metres away from the UPS. Initial configuration is carried out
by serial comms using any suitable terminal application (e.g.
Hyperterminal for Windows). The embedded HTTP server
presents an HTML interface to the network, which can be
accessed from any web browser. All system parameters
can be configured from here, including scheduled shutdown.
A sophisticated Java applet provides full monitoring in real time,
along with comprehensive event and history logs.
MANUAL AND STATIC BYPASS TO PROTECT
A manual by-pass switch allows power to be transferred directly
to the mains without disturbance to the load. The UPS can then
be safely powered down for maintenance or repair, on completion
of the work the UPS can be powered up and the load once again
transferred back to the UPS with no interruption in service. If
the power demand of your equipment exceeds the overload
level of the UPS the static switch defaults to the mains ensuring
continuous power in the event of system abuse or short term
overload conditions.
27
27
UPS - ONLINE (TRANSFORMER)
3 PHASE INPUT, 3 PHASE OUTPUT
Model*
ST20003360
ST20003380
ST200033100
ST200033120
ST200033150
ST200033200
80
100
120
150
200
Input Rectifier
Nominal Capacity - kVA
60
Input Nominal Voltage
200/208 V 3P or 380/400/415 V 3P + N or 440/465/480 V 3P
Nominal Frequency
50 / 60 Hz (Can be used as frequency converter)
Frequency Range
+ - 5%
P.F. @ 400V at Nominal
0,83 or 0,93 with Input Filter/PFC
Soft Start time
20-30 seconds
Battery
Charge Current (Max)
12Vdc x 32 = 384Vdc
20A
30A
40A
60A
Inverter Input
Nominal Voltage
192 V for 200/208 V – 384 V for 380/480 V
Inverter Output
Nominal Voltage
Current at p.f 0.8
200/208 V 3P or 380/400/415 V 3P + N or 440/465/480 V 3P
86.71
115.6
144
174
Nominal Frequency
50/60 Hz
THD Linear load
=<1,5%
THD at Non Linear load with Crest Factor 3:1
=<5%
Static Voltage Regulation
+ - 1%
Dynamic Voltage Regulation 0-100%
+ - 5%
221
287
Output Frequency Regulation
With Mains
Synchronisation (%)
+/- 1; 1,5 ;2,4
With Internal Micro
+ - 0,001%
Load Crest (Ipk/lrms)
Better than 3 : 1
Overload
110% for 60 min -- 125% for 10 min -- 150% for 1 min
Efficiency AC-AC @ 100%
93.4
93.5
94.1
95.1
Mechanical Data
Dimensions (W x H x D) (mm)
Weight (kg)
800 x 750 x 1200
580
630
1400 x 750 x 1200
670
700
900
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
2828
1100
UPS - ONLINE (TRANSFORMERLESS)
3 PHASE INPUT, 3 PHASE OUTPUT
MP MODULAR SERIES - 10-300KVA
FEATURES:
•Hot swappable for each module, easy maintenance
•Redundant and High Reliability
•Strong load adaptability for linear and nonlinear load
•Intelligent module and system protection design
•Double DSP controller for individual power module
•IGBT modules rather than discrete components are applied
in the power module.
•Friendly generator interface
•SNMP communication card
•Battery temperature compensation module
•Alarm and message module for mobile phone.
29
29
UPS - ONLINE (TRANSFORMERLESS)
1 PHASE INPUT, 1 PHASE OUTPUT
Specifications
Capacity
10-200KVA
300KVA
380V/400V/415V, -40%~+25%
380V/400V/415V,-20%~+25%
50/60Hz, 40-70HZ
50/60Hz, 40-70HZ
>0.99
>0.99
Main Input
Input voltage
Input frequency
Power factor
Battery
Battery voltage
±240VDC
±240VDC
Charger power
20%*Power
20%*Power
1%
1%
Charger voltage precision
Bypass
Bypass voltage
Bypass voltage window
Bypass overload capabiltiy
380V/400V/415V, three phase
380V/400V/415V, three phase
-20%-+15%, full load
-20%-+15%, full load, settable
125%< load <130%, last for more than 1 hour
< 115%, long time operation
130%<load<150%,last for more than 6 minutes
115%< load <120%, last for more than 1 hour
>1000%, last for more than 100ms
120%<load<125%,last for more than 10 minutes
Output
Output voltage
Voltage precision
Voltage THD
380V/400V/415V, three phase
380V/400V/415V, three phase
1% (balance load),1.5% (unbalance load)
0.5% (balance load),±1% (unbalance load)
THD<1.5%(linear load),THD<5%(nonlinear load)
THD<1%(linear load),THD<5%(nonlinear load)
Power factor
Phase tolerance
0.8
0.8
120°±0.5° (balance and unalance load)
120°±0.5° (balance and unalance load)
Crest factor
3:1
3:1
105%,long time operation
110%, transfer to bypass after 10 minutes
110%, transfer to bypass after 1hour
Overload capabiltiy
125%, transfer to bypass after 10 minutes
150%, transfer to bypass after 1 minute
125%, transfer to bypass 150%, transfer to bypass
after 1 minute after 1 minute
>150%, transfer to bypass after 200ms
System
System efficiency
Normal mode: 96%, ECO mode: 99%, Bat. Mode: 96%
Normal mode: 96%, ECO mode: 99%, Bat. Mode: 96%
LCD+LED, Touch screen and keyboard
LCD+LED, Touch screen and keyboard
Interface
(Communication Ports )
RS232,RS485,Dry contacts,SNMP
card,EPO,Generator interface
RS232,RS485,Dry contacts,SNMP
card,EPO,Generator interface
Operation temperature
0-400C
0-400C
Display
Storage temperature
Relative humidity
Noise(dB)
-25 C ~70 C
-250C ~700C
0-95% (non-condensing)
0-95% (non-condensing)
<55dB
<55dB
0
0
6-module cabinet / 150kg
Weight(kg)
10-module cabinet / 180kg
10-module cabinet / 180kg
10KVA: 20kg
15KVA: 21kg
Dimension(W x D x H)(mm)
20KVA: 22kg
30KVA: 22kg
6-module cabinet / 600 x 900 x 1600
10-module cabinet / 600*900*2000
10-module cabinet / 600 x 900 x 2000
Module / 440*600*134 (10KVA/15KVA/20KVA)
Module / 400 x 600 x 133 (30KVA)
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
30
30
INVERTER/CHARGERS
MODIFIED SINEWAVE
IG SERIES - INVERTER/CHARGER (600VA-2kVA)
•Simulated sinewave inverter
•Selectable input voltage range for home appliances and personal computers
•Auto restart with AC recovery
•Overload, and short circuit protection
•Cold start function
•Generator and Computer-related products compatible
•Reverse polarity protection.
Model
Capacity
IG600
IG1000
IG2000
600VA/300W
850VA/600W
2000VA/1200W
Input
Voltage
Selectable Voltage Range
220/230/240VAC
140-300VAC
90-280VAC (wide range), 170-280VAC (narrow range)
Frequency Range
50Hz/60Hz (auto-sensing)
Output
AC Voltage Regulation (Batt. Mode)
±10% (battery mode)
Frequency Range (Batt. Mode)
50Hz/60Hz ±1Hz
Transfer Time
10ms Typical
Battery
Battery Voltage
12Vdc
24Vdc
Floating Charge Voltage
13.7Vdc ±2%
26.8Vdc ±2%
Low Battery Alarm Voltage
10.2Vdc ±2%
21.6Vdc ±2%
Shutdown Voltage
9.9Vdc ±2%
20.0Vdc ±2%
Overcharge Protection
Maximum Charge Current
15Vdc ±2%
30Vdc ±2%
13A
10A or 20A optional
Alarm
Low Battery
Sounding every second
Overload
Sounding evry 0.5 seconds
Fault
Continuously sounding
Physical
Dimensions, L x W x H (mm)
Net Weight (kg)
358.5 x 96.8 x 146.5
5.8
232 x 293 x 82.5
2.35
2.55
Operating Environment
Humidity
0-90% Relative Humidity (Non-Condensing)
Operating Temperature
00C-500C
Storage Temperature
-150C-700C
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
31
INVERTER/CHARGERS
MODIFIED SINEWAVE
SKX-M SERIES - MODIFIED SINEWAVE
INVERTER (150W-3kW)
•Modified sinewave output
•With or Without Battery Charger
•High Surge Rating
•Hot Swappable Fuse
•Reverse Polarity Protection (Fuse).
Model
SKX-
150-
M-XX
SKX-
300-
M-XX
SKX500-
M-XX
SKX-
600-
M-XX
SKX1000-
M-XX
SKX1500
-M-XX
SKX2000M-XX
SKX2500M-XX
SKX3000-
M-XX
150
300
500
600
1000
1500
2000
2500
3000
Continuous Power (Watts)
150
300
500
600
1000
1500
2000
2500
3000
Surge Power (Watts)
300
600
1000
1200
2000
3000
4000
5000
6000
Capacity (Watts)
Output Waveform
Modified Sinewave
DC Input Voltage
10-15Vdc (12V Version) / 20-30Vdc (24V Version) / 40-60Vdc (48V Version)
AC Output Voltage
220-240VAC ± 10%
Output Frequency
50/60Hz ± 1Hz
Efficiency
No Load Current Draw
> 85%
< 0.25A
< 0.3A
< 0.8A
< 0.9A
< 0.95A
Protection
Low Voltage Alarm
10Vdc ± 0.2V / 20Vdc ±0.3V / 40Vdc ± 0.4V
Low Voltage Shutdown
9.5Vdc ± 0.2V / 19Vdc ± 0.3V / 38Vdc ± 0.4V
Over Voltage Shutdown
15.5V / 30.5V / 61.2V
Overload
Shut Off Output
Over Temperature
Shut Off Output
Environment
Operating Temperature
-100C - 500C
Operating Relative Humidity
20% - 90% RH non-condensing
Storage Temperature
-300C - 700C
Automatic Cooling Fan
Dimensions (mm)
Net Weight (kg)
Battery Charger Specs - Model
Charging Current
Turns on above 450C
140 x
105 x 55
150 x
105 x 55
180 x 105 x 55
0.5
0.6
0.8
0.8
1.7
2.4
2.6
5.9
6.1
SKX-
150MC-XX
SKX-
300MC-XX
SKX500MC-XX
SKX-
600MC-XX
SKX1000MC-XX
SKX1500MC-XX
SKX2000MC-XX
SKX2500MC-XX
SKX3000MC-XX
3A
5A
10A
10A
10A
15A
20A
20A
30A
Automatic Transfer Time
210 x 150
x 70
310 x 150 x 70
340 x 150 x 152
< 40ms
XX Denotes the DC Voltage - 12Vdc, 24Vdc and 48Vdc available
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at any time without prior notice.
32
INVERTER/CHARGERS
PURE SINEWAVE
SOLAR INVERTERS- PURE SINEWAVE
(150W-3kW)
•True sinewave output
•Power ON-OFF remote control
•Advanced microprocessor
•Input polarity / under voltage / over voltage protection
•Output short circuit / overload / over temperature protection
•Capable of driving highly reactive and capacitive loads
•Three color LED indicators.
Model*
Rated Power/Surge Power
S150-X
S300-X
S600-X
SK1000-X
SK1500-X
SK2000-X
SK3000-X
150W/200W
300W/400W
600W/800W
1kW/2kW
1.5kW/3kW
2kW/4kW
3kW/6kW
Output
AC Voltage
220/230/240VAC
Waveform
True Sinewave (THD < 6%)
True Sinewave (THD < 3%)
Frequency
50Hz / 60Hz
50Hz / 60Hz selectable by DIP switch
AC Regulation
± 5%
± 3%
Power Factor Allowed
cosѲ(-900) - cosѲ(+900)
LED Indicator
Input voltage level, output load level and fault status
Input
DC Voltage
No Load Current Draw
Voltage Ramge
Efficiency (typ. %)
12/24
0.22/0.16
12/24/48
0.26/0.28
0.83/0.43/0.22
1.2/0.6/0.28
10.5-15/21-30
87/88
89/89
1.4/0.7/0.4
2.64/1.32/0.65
2.8/1.5/0.7
10.5-15/21-30/42-60
90/93/94
91/93/94
90/93/94
91/94/95
90/93/94
Protection
Bat. Low Alarm
Bat. Low Shutdown
N/A
11V / 22V / 44V
10 ± 0.5V / 20 ± 1V
10.5V / 21V / 42V
Overload
Over Voltage
Shut off output voltage, re-power on to recover
15V-16V / 30V-32V
Over Temperature
15.3V / 30.6V / 61.2V
Shut off output voltage, recovers automatically after temperature goes down
Output Short
Shut off output voltage, re-power on to recover
Bat. Polarity Reverse
Fuses will become open
Environment
Working Temp.
0-400C
Working Humidity
20% - 90% RH non-condensing
Storage Temp. & Humidity
-300C-700C / -220F-1580F / 10%-95%
Safety & EMC
Isolation Resistance
EMI Conduction and Radiation
I/P - O/P: 100M Ohms / 500VDC
Compliance EN55022
class B
EMS Immunity
Compliance EN55022 class A
Compliance EN61000-3 -2, 3
LVD
Compliance EN60950-1
e-Mark
Compliance to e-13 * 72/245/EEC, 95/54/EC
Other
Dimensions, L x W x H (mm)
200 x 132
x 72
237 x 155
x 72
295 x 180
x 72
383 x 182
x 88
415 x 191
x 88
422 x 208
x 166
452 x 208
x 166
* X denotes the DC Voltage
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
33
33
INVERTER/CHARGERS
PURE SINEWAVE
SKX-S SERIES - PURE SINEWAVE INVERTER
(300W-5kW)
•Pure sinewave output
•With or Without Battery Charger
•High Surge Rating
•Hot Swappable Fuse
•Reverse Polarity Protection (Fuse)
•Remote Control Option: Control at a distance.
Model
SKX-
300-
S-XX
SKX-
500-
S-XX
SKX600-
S-XX
SKX1000-
S-XX
SKX1500-
S-XX
SKX2000-
S-XX
SKX2500-
S-XX
SKX3000-
S-XX
SKX5000-
S-XX
300
500
600
1000
1500
2000
2500
3000
5000
Continuous Power (Watts)
300
500
600
1000
1500
2000
2500
3000
5000
Max Constant Power Start (Watts)
360
600
720
1200
1800
2400
3000
3600
6000
Surge Power (Watts)
600
1000
1200
2000
3000
4000
5000
6000
10000
Capacity (Watts)
Output Waveform
Pure Sinewave (THD < 4%)
DC Input Voltage
10-15Vdc (12V Version) / 20-30Vdc (24V Version) / 40-60Vdc (48V Version)
AC Output Voltage
220-240VAC ± 10%
Output Frequency
50/60Hz ± 1Hz
Efficiency
> 90%
No Load Current Draw
< 0.6A
< 0.8A
< 0.9A
< 0.95A
< 1.5A
Protection
Low Voltage Alarm
10Vdc ± 0.2V / 20Vdc ±0.3V / 40Vdc ± 0.4V
Low Voltage Shutdown
9.5Vdc ± 0.2V / 19Vdc ± 0.3V / 38Vdc ± 0.4V
Over Voltage Shutdown
15.5V / 30.5V / 61.2V
Overload
Shut Off Output
Over Temperature
Shut Off Output
Environment
Operating Temperature
-100C - 500C
Operating Relative Humidity
20% - 90% RH non-condensing
Storage Temperature
-300C - 700C
Automatic Cooling Fan
Dimensions (mm)
Net Weight (kg)
Battery Charger Specs - Model
Charging Current
Automatic Transfer Time
Turns on above 450C
135 x
150 x 53
220 x 150 x 70
280 x
150 x 70
290 x 220
x 88
320 x
220 x 88
410 x 150 x 70
0.85
1.4
1.5
2.5
2.8
3
5.9
6.1
SKX-
300-
SC-XX
SKX-
500-
SC-XX
SKX600-
SC-XX
SKX1000SC-XX
SKX1500SC-XX
SKX2000SC-XX
SKX2500SC-XX
SKX3000SC-XX
5A
10A
10A
10A
15A
20A
20A
30A
< 40ms
XX Denotes the DC Voltage - 12Vdc, 24Vdc and 48Vdc available
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at any time without prior notice.
34
480 x 220
x 146
14
N/A
N/A
SWITCH MODE RECTIFIERS
1 PHASE & 3 PHASE
ES1948 SERIES - SWITCHING MODE
RECTIFIER
The PHD ES1948-48V/39.6A is a switched mode rectifier
(SMR) module designed to provide up to 39.6A of output
current into a 48V nominal system. This rectifier has been
designed especially to be used in conjunction with a battery to
provide an uninterruptable DC power system. The low noise
and high reliability make it ideally suited to telecommunications
applications. The rectifiers are designed to slide and plug into a
single magazine-SR1948-9, designed for a 19” rack, which can
accommodate up to 9 rectifiers and up to 32 rectifiers can be
configured as a system using one control and supervisory unit
(MCSU2048).
The ES1948 Switching Mode Rectifiers are highly compact,
highly efficient, fully featured switch mode rectifiers which can
operate in a modular rack environment with overall control from
the control and supervisory unit MCSU2048. With overall control,
such features as active current sharing, accurate battery voltage
regulation, battery recharging current limit control, automatic
battery equalization and battery temperature compensation
are achieved.
The ES1948 rectifier modules incorporate a microcontrollerbased control card which incorporates the control and supervisory
facilities of the SMR. The microcontroller enables digital
communications to the MCSU2048 as well as to the outside
world (via the MCSU2048), so that it is possible to examine the
operating parameters and, if necessary change them to suit a
particular situation, from a remote location, even a distant one if
a modem is used. This method of monitoring and control opens
up entirely new methods of routine and emergency maintenance
procedures.
INTERFACE BOARD AND OPTIONAL ACCESSORIES
MUIB: PHD’s MUIB board combined with MCSU, external
transducers and digital or analog I/O contacts to control and
monitor a 24V or 48V or 110V DC power system. It provides a
basic interface between the MCSU and the system environment.
WinCSU2000: PHD’s WinCSU2000 software is an intuitive
program designed for the Windows 95,98 and NT environments.
Working through MCSU and interface boards, you can monitor
and control PHD’s DC power system either locally or remotely
through a modem.
MCSU NetAgent ǁ: PHD has integrated various communication
protocols over networking to enable the equipment’s real-time
remote monitoring and management via MCSU NetAgent ǁ.
It is equipped with a UTP RJ45 plug for 10Base-T or 100M fast
Ethernet connecting through TCP/IP, UDP, HTTP, Telnet, SNTP,
PPP or SMTP protocol to LAN and WAN. It also has a RS232 port
to connect with an external modem to dial in via the PPP protocol
to access an internet connection.
FEATURES:
•Innovative single phase and three phase input stage with wide input range (90-275VAC, 310-480VAC)
•Power factor > 0.99
•High efficiency
•Microprocessor based
•Active or passive load sharing
•Rear “push in to plug in“ connection for AC, DC and communications link
•Weight less than 1.9kg
•Exceptional power density (>18W/in3).
APPLICATIONS:
•Telephone Exchanges
•Cellular Phone/ Radio Base Stations
•Satellite Base Stations
•Microwave Links Remote Multiplexes
•Rural Telecomunications
•PABX’s
•Railway Switching Controls
•Transmission and ISDN
•Equipment
•Power Plants
•Airport, Hospital, Banks.
MMIB (optional): PHD’s MMIB board is an add-on module for
the MCSU. It is used to monitor external AC power sources in
either single phase or three phase configurations
during operation.
BCM (optional): PHD’s BCM board is an add-on module for the
MCSU. It is used to monitor individual cells of a batteries during
either float, equalize operation, or discharge. Each BCM board
is capable of monitoring up to 24 cells(BCM) or 96 cells(BCM2).
SMM (optional): PHD’s SMM board is an expansion of the
MCSU. It allows the user to monitor the status of equipment
that is external to PHD’s DC power system. It can also be
used to monitor a 3rd party DC power system. Using the same
communication link and winCSU2000 software, the SMM can
supervise numerous off-site systems from a central monitoring
station.
35
35
SWITCH MODE RECTIFIERS
1 PHASE & 3 PHASE
Model
ES1948
Input
Voltage
Wide Input Range: 90-275Vac or 310-480Vac
Frequency
Input Protection
44~66 Hz
13A HRC fuses at input of SMR(line and neutral);
power circuit is turned off if the AC voltage exceeds 275Vac or falls to less than 90Vac
Current
Power Factor
THD
Efficiency
<12A rms
>0.99 at full load; sinusoidal wave shape
<5% at full load; satisfies requirements of EN61000-3-2
>91% at nominal mains voltage
Output
Voltage
Float: -Adjustable 48~59V; Equalise: -Adjustable 50~61V
Current Limit
Adjustable 5~40A
Power (Max)
1900W at 48~60Vdc(input>185Vac); 900W at 48~60Vdc(input 90~185Vac)
Load Sharing
Better than ±5% of full scale with active current sharing from MCSU2048
Protection
Static Regulation
Dynamic Regulation
Output Noise
Overvoltage - only faulty unit shuts down
Overcurrent - can sustain short circuit at output terminals indefinitely
Over-temperature - gradual reduction of current limit if heat-sink temperature exceeds pre-set limit
Line- +0.1%; Load- +1.0%
+3% for 10~90% or 90~10% load variation; +1% for +25% step change in AC input voltage
< 2mVrms Psophometric weighting; < 10mVrms 10kHz - 100MHz; < 100mV peak to peak 0~30MHz bandwidth
Other
Surge Protection
EMC
Inrush Current
Voltage Withstand Test
EN 61000-4-5
Emission: EN 61000-6-3,Immunity: EN61000-6-1
<12 Arms peak at nominal mains voltage
3.0 kVac – input and output (4.25 kVdc primary-secondary); 1.5 kVac – input earth (2.12 kVdc
primary-ground); 0.75 kVdc – output earth
Environmental
Audible Noise @ 1m
Operating Temperature
< 65dBA
Operating range -40 C ~ 700C; derated power at 500C ~ 700C
0
Cooling
Two fan cooled, speed controlled and alarmed
Humidity
0~95% non-condensing
Mechanical
Dimension (W x H x D)
Weight
41mm x 144mm x 287mm
<1.9kgs(4.19lbs)
Alarms
Alarm & Status LED
indication on SMR
Rectifier Alarms
On (Green) - SMR functioning normally
Alarm (Yellow) - Blinking when any SMR alarm is present.
Shutdown (Red) - Stays on when SMR has turned off due to a signal from the
MCSU2048 or an internal fault
Low/High output voltage alarm; Over voltage shutdown alarm; Current limit alarm; Fan Alarm;
Temperature alarm; Rectifier failure alarm
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
36
BATTERY CHARGER
FOR 192VDC & 240VDC SYTEMS
EXTERNAL BATTERY SUPER CHARGER
FEATURES:
DESCRIPTION:
•Compact and light
•Easy to install
•Battery overcharge protection
•Input surge protection.
The PHD external battery charger is suitable for any 192Vdc
and 240Vdc system (16 and 20 batteries in series). It is designed
for 192Vdc and 240Vdc UPS systems to enable longer standby
times for them. The 240Vdc version can be used with PHD’s T3
Series (6-10kVA models) and T4 Series (10-20kVA models) and the
192Vdc version can be used with PHD’s T3T Series (5-15kVA) and
T4T Series (10-15kVA). It is easy to install as it is connected
in parallel to the UPS’s existing battery charger.
Model
ST-CHARGER-10A
ST-CHARGER-12A
Input
Voltage
(176 -276)VAC @ Full Load
Frequency
(46 - 75)Hz for 50Hz system
Power Factor
≥[email protected] full load
THD
<20%@ full load
Output
Current
10A Nom. / 10A Max.
12A Nom. / 21A Max.
Voltage
160V Minimum, 218V Nominal, 224V Maximum
200V Minimum, 273V Nominal, 280V Maximum
Voltage Ripple
1%@ full load
Current Ripple
10% of Ah CAP @ full load
Efficiency
90%
Fault Protection
Output Reverse Polarity Protection
Fuse will open when reversing
Short-circuit Protection
Input Protection
Yes
276Vac(+/- 2%) Over Voltage, 176 Vac(+/- 2%) Under Voltage, 110%,1s Open Circuit
Fault Protection
Working and Storage Temperature
00C - 400C
Humidity
<95% (No condensing)
Altitude
< 1000m
Fault Protection
ESD
IEC 61000-4-2 Level 4
RS
IEC 61000-4-3 Level 3
EFT
IEC 61000-4-4 Level 4
Surge
IEC 61000-4-5 Level 4
Conduction
IEC/EN 62040-2 Category C3
Radiation
IEC 61000-3-2
Safety
IEC 60950-1/EN 60950-1
Drop, Variation
ISTA Procedure 2A
Mechanical Characteristics
Inlet, Outlet
Dimensions (W x D x H) (mm)
Net Weight (kg)
Terminal Block
200 x 352 x 450
340 x 250 x 110
15
6
37
37
BATTERY CHARGERS
MISCELLANEOUS
AC-DC BATTERY CHARGERS
FEATURES:
•Multi step charger setup and auto shutdown (tri step)
•Fast charge, normal charge and average charge
•Voltage with auto sensor battery
•Full charge with auto shutdown
•Output short circuit protection
•Universal input voltage suitable for worldwide operation
•Anti-reverse voltage protect device
•Fast charge transferred into slow charge
•Overload protection
•LED status display
•Suitable for lead acid battery.
Model
Input Voltage
Input
Frequency
Output
Current
Dimensions
(L x W x H) mm
Net
Weight
AC0212A
100-240VAC
50/60Hz
2A
14.6Vdc
AC0224A
100-240VAC
50/60Hz
2A
29.2Vdc
13.7Vdc
120 x 61.6 x 37.4
0.5kg
27.4Vdc
120 x 61.6 x 37.4
0.5kg
AC0312A
110/220Vdc ±10% AUTO SW
50/60Hz
3A
AC0324A
110/220Vdc ±10% AUTO SW
50/60Hz
3A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
29.2Vdc
27.4Vdc
186 x 88 x 47.5
0.8Kg
AC0412A
110/220Vdc ±10% AUTO SW
50/60Hz
AC0424A
110/220Vdc ±10% AUTO SW
50/60Hz
4A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
4A
29.2Vdc
27.4Vdc
186 x 88 x 47.5
0.8Kg
AC0512A
110/220Vdc ±10% AUTO SW
AC0524A
110/220Vdc ±10% AUTO SW
50/60Hz
5A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
50/60Hz
5A
29.2Vdc
27.4Vdc
186 x 88 x 47.5
AC0612A
0.8Kg
110/220Vdc ±10% AUTO SW
50/60Hz
6A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
AC0624A
110/220Vdc ±10% AUTO SW
50/60Hz
6A
29.2Vdc
27.4Vdc
186 x 88 x 47.5
0.8Kg
AC0712A
110/220Vdc ±10% AUTO SW
50/60Hz
7A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
AC0724A
110/220Vdc ±10% AUTO SW
50/60Hz
7A
29.2Vdc
27.4Vdc
186 x 88 x 47.5
0.8Kg
AC0812A
110/220Vdc ±10% AUTO SW
50/60Hz
8A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
AC1012A
110/220Vdc ±10% AUTO SW
50/60Hz
10A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
AC1212A
110/220Vdc ±10% AUTO SW
50/60Hz
12A
14.6Vdc
13.7Vdc
186 x 88 x 47.5
0.8Kg
AM0236A
100-240VAC
50/60Hz
2A
44.5Vdc
41.3Vdc
164 x 90 x 50
0.5kg
AM0424A
100-240VAC
50/60Hz
4A
29.6Vdc
27.4Vdc
164 x 90 x 50
0.5kg
AM0612A
100-240VAC
50/60Hz
6A
14.8Vdc
13.6Vdc
164 x 90 x 50
0.5kg
Other currents and voltages available on request
38
Output
Output
Equaliser
Floating
DC Voltage DC Voltage
GENERATORS
1 PHASE & 3 PHASE
STANDBY DIESEL GENERATOR SETS
(10kVA-2000kVA)
FEATURES:
All units complete with exhaust systems, 12 hour fuel tanks
(larger tanks available), batteries, automatic mains failure
control panels and prime power base load control panels.
The panels include standard metering switchgear, control gear
and engine protection. Both single and three phase versions
available.
APPLICATIONS:
300KVA Automatic mains failure
•Agriculture
•Cold Rooms
•Banking
•Airports
•Building Services
•Hospitals
•Hotels and Entertainment
•Engineering.
SPECIFICATIONS:
Engine Types: Caterpillar, Cummins, Daimler Chrysler
MTU, Detroit Diesel VM Sun, Deutz, Hatz,
John Deere, Kirloskar, Lister, Lombardini,
Perkins, Scania, Volvo and Yanmar
Alternator Types: Leroy Somer, Marelli and Mecc Alte
Sizes: Petrol powered up to 10KVA Single Phase; Diesel Powered from 10KVA to 2000KVA
Three Phase
Voltage Ranges: 110V-525V
Frequencies: 50/60Hz
Engine Speeds: 3000 or 1500 RPM
Generator Sets: Available with Base Load and Automatic Mains Failure Control Panels mounted on open steel frame. Weatherproof Silent Canopy.
Mobile Trailer mounted.
All engines and alternators used in the manufacture of Power
Generation Equipment conform to the following specifications:
ENGINES: B.S. 5514 1982; ISO 30461; 1DIN6271.
ALTERNATORS: B.S. 5000; VDE 30; IEC 23; UTE 5100;
NEC 51-111; NEMA – IEEE CSA.
Where applicable alternators specified for Marine Applications will
conform to: BUREAU VERITAS; LLOYDS REGISTER; AMERICAN
BUREAU OF SHIPPING; DNV; RINA; GERMANISHER LLOYDS;
KOREAN REGISTER OF SHIPPING; NKK.
100KVA, 25KVA, 13KVA remote start/stop and AMF
1000KVA Automatic mains failure Generator
Set. MTU 16V 2000 G62 / Leroy Somer
(Installed at the Capital Alliance Building,
Johannesburg)
30KVA Automatic mains failure soundproof
Generator Set. Standard soundproof
canopy with sound levels of 65dB(A) at
7 metres in an open field.
39
39
CONSTANT VOLTAGE TRANSFORMERS
1 PHASE
CONSTANT VOLTAGE TRANSFORMERS
(150VA-20kVA)
FEATURES:
•Input Voltage: Single Phase, 230V (184-276).
Other voltage on request
•Supply Frequency: 50Hz
•Output Voltage: 230V. Other voltages on request
•Output Accuracy: Btter than 3% (1% option available)
•Harmonic Distortion: Typically less than 2%
•Effect of Frequency Change: 1% change in frequency produces approximately 2.5% change in output voltage
•Response: Typically 1-2 cycles (20-40ms)
•Overload: Short circuit limited
•Efficiency: Approximately 85% at full load.
40
Model*
Input/Output
Rating
Current
Dimensions (W x H x D) mm
Mass
SC150S
230V/230V
120W
0.52A
290 x 231 x 400
17kg
SC250S
230V/230V
200W
0.87A
290 x 231 x 400
18kg
SC500S
230V/230V
400W
1.74A
290 x 231 x 400
21kg
SC750S
230V/230V
600W
2.61A
290 x 231 x 400
24kg
SC1000S
230V/230V
800W
3.48A
290 x 231 x 400
26kg
SC1500S
230V/230V
1200W
5.22A
290 x 231 x 400
36kg
SC2000S
230V/230V
1600W
7.27A
400 x 263 x 550
55kg
SC2500S
230V/230V
2000W
9.09A
400 x 263 x 555
59kg
SC3000S
230V/230V
2400W
10.91A
400 x 263 x 565
65kg
SC4000S
230V/230V
3200W
14.55A
400 x 263 x 600
83kg
SC5000S
230V/230V
4000W
18.18A
400 x 263 x 600
90kg
SC6000S
230V/230V
4800W
21.82A
540 x 365 x 908
154kg
SC7500S
230V/230V
6000W
27.27A
540 x 365 x 925
172kg
SC10000S
230V/230V
8000W
36.36A
540 x 365 x 970
212kg
SC12000S
230V/230V
9600W
43.64A
450 x 890 x 1100
290kg
SC15000S
230V/230V
12000W
54.55A
450 x 890 x 1100
340kg
SC18000S
230V/230V
14400W
65.45A
450 x 890 x 1100
435kg
SC20000S
230V/230V
16000W
72.73A
450 x 890 x 1100
450kg
SERVO TYPE
1 PHASE
SERVO TYPE FULLY AUTOMATIC VOLTAGE
STABILISER (SINGLE PHASE)
DESCRIPTION:
The SVC fully automatic voltage regulator consists of a contact
voltage regulator, samplingcontrol circuit and service motor as well.
It features small waveform distortion, high efficiency and high power
factor. It is also not affected by input frequency variations.
It can be widely used in most situations where voltage
stabilisation is required.
Model
500VA
1kVA
Input Voltage
1.5kVA
2kVA
3kVA
5kVA
150V-250V
7.5kVA
10kVA
220V ± 3%
Frequency
50Hz/60Hz
Response Time
< 1s (against 10% input voltage deviation)
Efficiency
> 90%
Ambient
Temperature
-100C ~ +400C
Relative Humidity
< 90%
Power Factor
0.8
Insulation
Resistance
> 5MΩ
18.5
21
21
27.5
29
45
47
20kVA
30kVA
150V-250V
Output Voltage
Length (cm)
15kVA
160V-250V
47
42
42
42
Width (cm)
15
18
18
23.5
23
24
26
26
38
38
38
Height (cm)
12.5
14.5
14.5
18.5
22
18.5
22
22
73
73
83
Weight (kg)
4.6
6.5
7
10.5
13.6
22.4
40
43
75.5
80
87
Append “SVC-” to the model above for the full part number
41
41
SERVO TYPE
3 PHASE
SERVO TYPE FULLY AUTOMATIC VOLTAGE
STABILISER (THREE PHASE)
DESCRIPTION:
•Microprocessor DSP control
•Automatic Voltage Regulation
•Protection against Brownouts and Overvoltages
•Short Circuit & Overload Protection
•Digital meter indicates line voltage and regulated voltage
•LED indicators to show status of working input and output
•Selectable Delay Time
•Built-in transformer, Square transformer or Servo motor
•Surge, Spike & Lightning Protection.
Model*
10kVA
15kVA
20kVA
30kVA
Input Voltage
50kVA
80kVA
100kVA
150kVA
Input Frequency
50/60Hz
Output Voltage
380/400/415VAC
Output Precision
± 3%
Efficiency
98%
LED Display
Input Voltage / Output Voltage
LED Input Status
Blue; indicating phase voltage normal/abnormal
LED Power Status
Red; indicating Power ON/OFF
LED Delay Status
Yellow; during delay the LED flashes
LED Output Status
Blue; indicating output voltage ON/OFF
Protection
High Voltage, Low Voltage, Overload, High Temp.
Safety Standards
CE, EN60950, EN55024
Operating/Storage Temp.
00C-400C / -150C-450C
Operating Humidity
10% RH - 102% RH, non-condensing
Dimensions, L x W x H (mm)
443 x 483 x 858
Weight (kg)
57.8
62.3
503 x 553
x 888
503 x 553
x 938
1250 x 525
x 650
88.4
108.4
200
1020 x 620 x 1360
250
285
1200 x 680 x 1760
305
* Append “PDR-“ to the model above for the full part number
Bigger ratings available on request
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at any time without prior notice.
42
200kVA
260-430VAC
350
ELECTRONIC WITH ISOLATION
1 PHASE & 3 PHASE
VOLTAGE STABILISER - ELECTRONIC
(15kVA-30kVA)
SPECIFICATIONS:
FEATURES:
•Wideband voltage regulation range (±25%)
•True RMS voltage sensing ensures accurate regulation even
with distorted mains (eg diesel generator)
•Regulates individual phases to within 5% with input variations
of up to ±25%
•High capability to temporary overloads
(eg aircon units, power supplies etc)
•Over/Under voltage cut-out protects sensitive loads
•TVSS Surge protection
•Volt meter (optional)
•High efficiency - approximately 98% at full load
•Rugged and reliable.
APPLICATIONS:
•Transmissions and telecommunications
•Radar systems in naval or air navigation
•Process controls
•Computer data processing & numerical control machines
•Photography controls and processes
•Laboratory equipment
•Test equipment
•Electric furnaces
•Illumination
•Medical equipment
•Any electrical or electronic sensitive to voltage variations.
Nominal Input Voltage: 400/230vac 50/60 Hz +/- 25%
(3 Wire)
Nominal Output Voltage: 400/230vac 50/60 Hz +/- 5%
(4 Wire)
Over Voltage Cut-off at: 290V input voltage under normal
operation (L-N) (U out 230V) 250V input voltage under bypass
operation (L-N) (U out 230V)
Under Voltage Cut-off at: 160V input voltage under normal operation (L-N) (U out 230V) 200V input voltage under bypass
operation (L-N) (U out 230V)
Output Voltage Accuracy: 5%
Overload Rating: 120% for 60mins; 200% for 10 sec
Efficiency: 98% at full load
Earthing: The input earth is bonded to the enclosure
Speed Correction: +/- 20 milliseconds
Waveform Distortion: Negligible
Effect of load Power Factor: None
Maximum Continuous Voltage: 300V
Nominal Discharge Current: 40kA
Impulse Current Limp (10/350us)kA:12kA
Voltage Protective Level: ≤ 2.0
Response Time: ≤ 100ns
Environment: Protection class IP21 (indoor enclosure); IP54 (outdoor enclosure)
Ambient Operating Temperature: 0°C to +45°C
Operating Elevation: 1000m, over 1000m derate by 2.5% for each 500m
Model
Description
Rating
Current
Dimensions (L x W x D mm)
Weight
APS-15kVA-ID
Indoor - 15kVA
15kW
66A (Max)
700 x 385 x 1100
210kg
APS-22.5kVA-ID
Indoor - 22.5kVA
22.5kW
96A (Max)
700 x 385 x 1100
226kg
APS-30kVA-ID
Indoor - 30kVA
30kW
132A (Max)
700 x 385 x 1100
236kg
APS-15kVA-OD
Outdoor - 15kVA
15kW
66A (Max)
775 x 465 x 1210
216kg
APS-22.5kVA-OD
Outdoor - 22.5kVA
22.5kW
96A (Max)
775 x 465 x 1210
232kg
APS-30kVA-OD
Outdoor 30kVA
30kW
132A (Max)
775 x 465 x 1210
242kg
Note: Higher ratings available on request
43
43
ELECTRONIC
1 PHASE & 3 PHASE
VOLTAGE STABILISER - ELECTRONIC
(1kVA-75kVA)
No Load Energy
Consumption Relationship
30%
20-25%
FEATURES:
•High Efficiency
•High Power Factor
•High Reliability
•Low Harmonic Distortion
•Low Environmental Pollution
•Low Electro Magnetic Interference
•APS Range of Products Solve Over 95% of Your Power Problems
•Micro Processor Control
•Micro Size - Quarter the size / weight of traditinal AVR
•Modular Design - Circuit designed in PCB modules, easy for maintenance
•High Efficiency - η ≥ 98% at Full Load.
•High Input Power Factor - Input Power Factor 0.95 ~ 1
•Extra Low No Load Power Consumption - No Load Power Consumption ≤ 1.5%
•Automatic Electronic Bypass - Electronic Bypass, Automatic in Overload / Abnormal conditions
•Low Audible Noise - Audible noise 35 dB at 1 m
•Flexibility for Loads - Suitable for Pure Capacitive / Inductive Load.
1.5%
SCR Phase
Control
Transductor
Principle
APS
No Load Electricity
Cost Relationship
Ferroresonant
Transformer
CVT
±R30 000
±R20 000
±R1 600
APS
SCR Phase
Control
Transductor
Principle
Ferroresonant
Transformer
CVT
Calculation Based on typical South African
Electricity Cost, 10 hours per day
APS Single Phase Models
Model
KVA
Output Regulation
Type
Current (A) (1 Phase)
Dimensions (H x W x D) (mm)
Weight
(kg)
APS-1KB
1
±3% Typical
B
4.5
120 x 220 x 360
10
APS-2KB
2
±3% Typical
B
9.1
120 x 220 x 360
13
APS-3KB
3
±3% Typical
B
14.0
200 x 380 x 450
21.5
APS-5KB
5
±3% Typical
B
23.0
200 x 380 x 450
26
APS-7KB
7
±3% Typical
B
32.0
200 x 370 x 550
33
APS-10KB
10
±3% Typical
B
45.0
200 x 370 x 550
39
APS-15KB
15
±2% Max
B
68.0
200 x 370 x 550
45
APS-20KB
20
±2% Max
B
91.0
355 x 835 x 650
50
APS-30KB
30
±2% Max
B
137.0
355 x 835 x 650
55
Dimensions (H x W x D) (mm)
Weight
(kg)
APS Three Phase Models
Model
KVA
Output Regulation
Current (A) (per Phase)
APS-10KZ
10
±3% Typical
Z
15
355 x 835 x 650
70
APS-15KZ
15
±3% Typical
Z
23
355 x 835 x 650
85
100
APS-22KZ
22
±3% Typical
Z
33
355 x 835 x 650
APS-30KZ
30
±3% Typical
Z
45
355 x 835 x 650
115
APS-45KZ
45
±2% Max
Z
68
355 x 835 x 650
130
APS-60KZ
60
±2% Max
Z
91
450 x 955 x 800
160
APS-75KZ
75
±2% Max
Z
114
450 x 955 x 800
185
Note: Higher ratings available on request
44
Type
ELECTRONIC
INDUSTRIAL INDUCTIVE TYPE
VOLTAGE STABILISERS - INDUCTIVE
(100kVA-1500kVA)
FEATURES:
•Strong, durable and high reliability - No contact point.
Capable of sustaining spikes, surges or impulses from
non-lionear loads. Long equipment life.
•Protection - Redundant circuit control.
Event history log for up to 200 events. Phase loss and phase reverse protection. Output over voltage and under voltage protection. Output overload protection.
•High overload capability - 100% continuous load.
200% transient current up to 5 minutes. Maximum tolerable transient start current of up to 500%
•LCD user interface - Blue backlight, wording in white.
RS-485 communication port. Push buttons are lit for
convenience in the dark. Remote signal for measurements
and control functions to monitor and control your equipment.
•1500kVA capacity - The inductive type voltage stabiliser can
have a maximum capacity of 1500kVA in one unit.
APPLICATIONS:
•Communication Systems - TV stations, ADSL, Coaxial cable TV systems and components, Radio communication equipment and systems, Satellite and communication equipment,
Fiber-optics systems, Lan servers.
•IT - Home electrical appliances, Information appliances,
Office IT equipment, POS systems.
•Computer and Computer Peripherals - Electronic data processing (EDP) centres, Server / Data storage systems, Industrial PC’s.
•General Lab - Program control systems, Electronic test equipment.
•F / A - Production lines, IC (integrated circuit) field, CNC machines, SMT equipment, Auto-Insertion equipment, PCB assembly equipment, Semiconductors (BGA, CSP,
Flip Chip, LCD), Production process and control equipment, Printing industry.
•Medical and Military - Electronic and Medical equipment,
Medical monitoring systems, Airport x-ray scanning equipment, Airport facilities, Airport control tower facilities.
•Other - Bioscience, Gas stations, Opto-electronic industry.
45
45
ELECTRONIC
INDUSTRIAL INDUCTIVE TYPE
Model**
Capacity (kVA)
0100
100
0125 0150
125
150
0200
0250
0300
0350
0400
0500
0600
200
250
300
350
400
500
600
Circuit Type
0800 1000
800
1000
1250
1500
1250
1500
Inductive Voltage Regulator
Input
Phase
3P3W / 3P4W
Voltage Range*
-13% - +17% (option: -22% - +30%)
Frequency
47Hz - 63Hz
Output
Phase
3P3W / 3P4W
Voltage
200V / 208V / 220V, 380V / 400V / 415V ± 2% (±1%-±5% adjustable)
Voltage Modulation
< 4 V/s
Overload
125%-40min; 150%-20min; 175%-10min; 200%-5min
Total Harmonic
Distortion
< 1% (compared with input)
VA Efficiency
>97%
Measurement
Measurements
Input line voltage and frequency, Output line voltage, Phase voltage, Line current and frequency,
VA, W, PF, Load rate, Internal temperature
Protection
Protection
Functions
Phase loss, phase reverse, output over voltage & under voltage, output overload, over temperature, over current,
redundant cicuit control. Event history log for 200 events.
User Interface
Operation
LCD and Push buttons
Alarm
Alarm 1. Audio. Alarm 2. Activate
Communication
RS-485
Software
Remote control and monitor
Environment
Working
Temperature
-50C-400C
Storage
Temperature
-300C-500C
Humidity
< 95% (non-condensing)
Altitude
< 1000 meters
Cooling System
Type
Fan cooling
Other
Noise
Optional
< 60dB
Auto transformer, full time lightning & surge protection, output on & off electromagnetic contactor
* Other input ranges on request
**Prefic the model no. with APH-33 for the full part number.
Custom made specifications on request
All information contained in this brochure is purely indicative and can not be used to form any contractual obligations.
Specification or design can be changed at anytime without prior notice.
46
FREQUENCY CONVERTERS
1 PHASE & 3 PHASE
FREQUENCY CONVERTERS (500VA-300kVA)
FEATURES:
•Wide Application: Allows users to simulate Worldwide voltage
and frequency for commercial applications (47-63Hz) and
Military / Avionics / Marine applications at 400Hz.
•Pure Sinewave Output: All models generate very clean sine waveforms output. It is not only a superior power source for R&D and Laboratory, but also a standard power source for EMI/EMC/
Safety testing.
•Superior Stability: Output Load Voltage regulation ±1%,
Output Frequency ≤ 0.01%.
•Quick & Convenient 3 Scales of Preset Voltage for High
and Low Voltage Simulation:
- High (Surge): +10% ~ +25% of Present voltage,
- Medium: Preset voltage,
- Low (Sag): -10% ~ -30% of Preset voltage.
•Direct Select of Six Scales Output Frequency: 47~63Hz, 50Hz, 60Hz, 2xF (F = Input Frequency), 4xF (F = Input Frequency), 400Hz.
•2F or 4F Output Testing Frequency for Layer Short Test of
Coils Products.
•High Overload Capability: 100% full load continuously;
withstand 3 times of inrush current.
•Protections: Input Circuit Breaker, Output Circuit Breaker,
Instant Trip Circuits for Overload, Over Voltage, Short Circuit, Over Temperature protection and Alarm system.
•Suitable for Any Load: Resistive, Capacitive, Inductive
and Non-linear load use.
General Laboratory:
•AC Power Source Testing
•Life & Safety Testing
•EMC Testing
•OQC (FQC) Testing
•Product Testing
•Product Researches & Developments.
400Hz Output Frequency:
•Aerospace
•Airport Grounding Facilities, including Airport Terminals, Control Towers, Aprons
•Avionics Equipment
•Air Force System Diagnostics
•Military System Diagnostics
•Navy System Diagnostics
•Marine Systems
•Satellite Navigation
•Switching Power Supply of Super Computers
•400Hz Equipment & Instruments.
AFC-SERIES 500VA-60kVA SINGLE PHASE
APPLICATIONS:
Industrial:
•Home Electrical Appliances, Manufacturers of:
Washing Machines, Refrigerators, Vacuum Cleaners, Microwave Ovens, Air Conditioners, Blenders.
•Electronic Manufacturers of: Switching Power Supply Testing, Ballasts (in Bulbs, Fluorescent Lamps), Uninterruptible Power Supplies, Chargers, Relays, Passive components.
•Electric Machinery Manufacturers of: Compressors, Transformers, AC Fans, Motors.
•IT Field: OA Equipment (Fax Machines, Copy Machines, Shredders, etc), Computer & Monitors, Printers,
Scanners & Peripherals.
AFC-SERIES 60kVA-300kVA THREE PHASE
47
47
FREQUENCY CONVERTERS
1 PHASE & 3 PHASE
AFC SERIES - SINGLE PHASE SPECIFICATIONS:
Model
Capacity (kVA)
Voltage
AFC-500
AFC-11001
AFC-11003
AFC-11005
AFC-11010
AFC-11015
AFC-31020
AFC-31030
AFC-31045
AFC-31060
0.5
1
3
5
10
15
20
30
45
60
110V or 220V ±15%, 1 Phase
220V ±15%, 1 Phase
Frequency
Output
(AC)
50Hz ± 3Hz, 60Hz ± 3Hz
Phase
Voltage
380V ±15%, 3 Phase 3 or 4 wire
Single Phase
Low
0~150V
5V ~ 150V (L-N)
High
0~300V
10V ~ 300V (L-N)
Frequency
47 ~ 63Hz, 50Hz, 60Hz, 400Hz, 2F (2 x Input Frequency), 4F (4 x Input Frequency)
Option: 40 ~ 500Hz
Maximum Current
Low
4.2A
8.4A
25A
42A
84A
126A
168A
250A
375A
500A
High
2.1A
4.2A
12.5A
21A
42A
63A
84A
125A
188A
250A
Frequency Stability
≤0.01%
Load Regulation
±0.2%
±1% (linear load)
Total Harmonic Distortion
±0.2%
±2% (linear load)
Transient Response
Meter /
Res.
50us Max.
Res. 0.1Hz
4 Dig. Voltmeter
Digit Ammeter
4 Dig. Wattmeter
Res. 0.1V
0.001A
0.01A
0.1W
1W
Protection
Envionment
2ms Max.
4 Dig. Freq. Met.
4 Digit Ammeter / Res. 0.1A
5 Digit Ammeter / Res.0.1A
Option
Input Circuit Breaker, Output Circuit Breaker, Electronic Circuits Instant Trp for Over Voltage, Over Load, Over Temperature,
Short Circuit Protection and Alarm System
Ambient Temp.
0°C ~ 45°C
Relative Hum.
0 ~ 90% Non-condensing
Altitude
1500 meter
Dimensions W x H x D (mm)
430x520x200
Net Weight (kg)
430x520x720
44
89
430x750x990
73
600x970x1240
800x600x1600
89
150
171
280
333
418
571
AFC SERIES - THREE PHASE SPECIFICATIONS:
Model
Capacity (kVA)
AFC-33006
AFC-33010
AFC-33020
AFC-33030
AFC-33045
AFC-33060
AFC-33075
AFC-33100
AFC-33150
AFC-33180
6
10
20
30
45
60
75
100
150
180
Voltage
380V ±15%, 3 Phase 3 or 4 wire
Frequency
Output
(AC)
50Hz ± 3Hz, 60Hz ± 3Hz
Phase
Voltage
Three Phase
Low
5V ~ 150V (L-N)
High
10V ~ 300V (L-N)
Frequency
47 ~ 63Hz, 50Hz, 60Hz, 400Hz, 2F (2 x Input Frequency), 4F (4 x Input Frequency)
Option: 40 ~ 500Hz
Maximum Current
Low
16.7A
27.8A
55.6A
83.3A
125A
167A
208A
278A
417A
500A
High
8.3A
13.9A
27.8A
41.7A
62.5A
83.3A
104A
139A
208A
250A
Frequency Stability
≤0.01%
Load Regulation
≤ ±1% (linear load)
Total Harmonic Distortion
≤ ±2% (linear load)
Transient Response
Meter /
Res.
2ms Max.
4 Dig. Freq. Met.
Res. 0.1Hz
4 Dig. Voltmeter
Res. 0.1V
Digit Ammeter
4 Digit Ammeter / Res. 0.1A
4 Dig. Wattmeter
5 Digit Ammeter / Res.0.1A
Option
Load Balance or No Load: ≤ 1°, 100% Unbalance: ≤ 2° (measured at 50Hz or 60Hz)
Protection
Envionment
Input Circuit Breaker, Output Circuit Breaker, Electronic Circuits Instant Trp for Over Voltage, Over Load, Over Temperature, Short Circuit Protection and Alarm System
Ambient Temp.
0°C ~ 45°C
Relative Hum.
0 ~ 90% Non-condensing
Altitude
Dimensions W x H x D (mm)
Net Weight (kg)
48
1500 meter
430x750x990
150
600x970x1240
175
345
385
800x1090x1600
528
635
700
800x600x1600
1000
1350
1620
GROUND MILITARY UNITS
1 PHASE & 3 PHASE
GROUND - MILITARY POWER UNITS
(500VA-300kVA)
400Hz Frequency Converters &
28VDC Power Supplies
28VDC Power Supply
FEATURES:
•Used as a DC power supply unit or voltage simulating test for GPU / Military Unit
•28VDC ±10% Standard Output Voltage; 100Amp to 2,000Amp Output Current
•Automatic Input Line Monitoring
•Output Voltage and Output Current Monitoring
•Current Limit Adjustable
•Auto Feedback Control Circuits. Capable to adjust input and output automatically for constant voltage
•Automatic Line Drop Compensation
•Fixed voltage Fixed current. Interchangeable to have control
and protection features.
•Protection: Input Line Loop: Auto detection and trip for Over Current, Over Voltage, Loss Phase, Phase Reversed.
Output Circuit: Electronic-controlled Short Circuit Protection.
400Hz Solid State Frequency Converter
FEATURES:
•Small, Light & Space Saving: Typically, 1/4 size of
motor-generator sets of the same power output rating.
•High Efficiency, Optimum Stability, Superior Heat Dissipation.
•Economical Cost of Ownership.
•Modular design permits quick and easy replacement: - Typical motor-generator sets downtime is four times greater, often resulting in costly delays, maint. and production schedules.
- High efficiency features reduce operating costs through
25% and upward utility savings compared to motor-generator sets.
- On-site repairs are easily accomplished.
- Motor-generator sets quite often must be removed from location for repairs, resulting in costly rigging and transport charges.
•Low Noise: Solid State frequency converters have no moving mechanical parts generating a loud noise and eliminates the need for expensive sound insulation.
•Individual Phase Regulation at Output: Excellent voltage regulation under 100% unbalanced load.
•Output Isolation Transformer: capable of sustaining CEMF (counter-electromotive force).
•Option:
- 36VAC input voltage or acc. to customer’s specifications
- “Add on module” of Solid State frequency converter
and 28VDC power supply
• Low Harmonic Distortion at 3% maximum.
APPLICATIONS FOR BOTH:
•Provides DC current for Airlines / Spacecraft starting
•Working current on avionics or simply provide ground
support maintenance
•Provides clean DC power that meets MIL-STD-704
standard for aircraft power
•Input Power Supply Simulating Test of air materials
•Aircraft Manufacturers
•Aerospace Equipment Manufacturers
•Hangars
•Air Force Bases
•Passenger Boarding Bridges (PBB)
•Aprons
•Control Towers
•Meter Control Centers
•Air Force System Diagnostics
•Military System Diagnostics
•Navy System Diagnostics
•R&D Dept. of Military, Defense
•Military Equipment
•Power Supply for Warships
•Power Supply for Radars
•Rotary Engineer Manufacturers.
49
49
GROUND MILITARY UNITS
1 PHASE & 3 PHASE
AMF SERIES - SINGLE PHASE SPECIFICATIONS:
Model
Capacity (kVA)
AMF-500
AMF-11001
AMF-11003
AMF-11005
AMF-11010
AMF-31020
AMF-31030
AMF-31045
AMF-31060
AMF-31100
0.5
1
3
5
10
20
30
45
60
100
Circuit Type
Input
(AC)
IGBT / Pulse Width Modulation Type
Phase
Voltage
1 Phase 2W+G
110V (B) or 220V (G) ±15%
3 Phase 3W+G(Δ) or 3 Phase 3W+N+G(Y)
220V (G) ±15%
Frequency
Output
(AC)
220V (G) ±15% or 220V/380V (T) ±15%
50Hz ±3Hz, 60Hz ±3Hz
Phase
1 Phase 2 W+G
Voltage
115V (C) or 220V (G), 230V (H) Output Voltage ±10% Adjustable
Frequency
2-Step Output Frequency: 1. 400Hz Fixed, 2. 350Hz-450Hz adjustable (*can comply with customer’s specs)
Frequency Stability
≤0.01%
Load Regulation
Total Harmonic Distortion
Meter /
Res.
≤±1%
≤±1.5%
≤±2% (linear load)
≤±3% (linear load)
4 Dig. Freq. Met.
Res. 0.1Hz
4 Dig. Voltmeter
Digit Ammeter
Res. 0.1V
0.001A
0.01A
4 Digit Ammeter / Res. 0.1A
Overload Capability
Protection
5 Digit Ammeter / Res.0.1A
120% / 1hr - 150% / 1min. - 200% / 15sec. (25% duty cycle)
Input Circuit Breaker, Output Circuit Breaker, Electronic Circuits for fast detection and trip off protection for Over Current, Over Voltage, Over Load, Over
Temperature, Short Circuit and Alarm system
Isolation Resistance
≥500Vdc 20MΩ
Withstand Voltage
1800Vac / 5mA / 1min
Cooling System
Air Forced Fan
Ambient Temperature
-20°C ~ 45°C
Relative Humidity
0 ~ 90% Non-condensing
Dimensions W x H x D (mm)
Net Weight (kg)
430x520x200
430x520x720
44
60
430x750x990
73
89
600x970x1240
800x1090x1600
800x600x1600
150
280
333
418
571
898
AMF SERIES - THREE PHASE SPECIFICATIONS:
Model
Capacity (kVA)
AMF-33006
AMF-33010
AMF-33020
AMF-33030
AMF-33045
AMF-33060
AMF-33075
AMF-33100
AMF-33150
AMF-33180
6
10
20
30
45
60
75
100
150
180
Circuit Type
Input
(AC)
IGBT / Pulse Width Modulation Type
Phase
3 Phase 3W+G (Δ) or 3 Phase 3W+N+G(Y)
Voltage
3W+G : 220V (G) or 3W+N+G : 220V/380V (T) ±15%
Frequency
Output
(AC)
50Hz ±3Hz, 60Hz ±3Hz
Phase
3 Phase 3 W+N+G (Y)
Voltage
200V/115V (P) Output Voltage ±10% Adjustable
Frequency
2-Step Output Frequency: 1. 400Hz Fixed, 2. 350Hz-450Hz adjustable (*can comply with customer’s specs)
Frequency Stability
≤0.01%
Load Regulation
Total Harmonic Distortion
Meter /
Res.
≤±1%
≤±1.5%
≤±2% (linear load)
≤±3% (linear load)
4 Dig. Freq. Met.
Res. 0.1Hz
4 Dig. Voltmeter
Res. 0.1V
Digit Ammeter
4 Digit Ammeter / Res. 0.1A
Phase Shift
Overload Capability
Protection
120% / 1hr - 150% / 1min. - 200% / 15sec. (25% duty cycle)
Input Circuit Breaker, Output Circuit Breaker, Electronic Circuits for fast detection and trip off protection for Over Current, Over Voltage, Over Load, Over
Temperature, Short Circuit and Alarm system
Isolation Resistance
≥500Vdc 20MΩ
Withstand Voltage
1800Vac / 5mA / 1min
Cooling System
Air Forced Fan
Ambient Temperature
-20°C ~ 45°C
Relative Humidity
Dimensions W x H x D (mm)
Net Weight (kg)
50
5 Digit Ammeter / Res.0.1A
Balanced Load / Empty Load: ±2° : 100% Unbalanced Load: ±4°
0 ~ 90% Non-condensing
430x750x990
150
175
600x970x1240
345
385
800x1090x1600
528
635
700
800x600x1600 (x3)
1000
1350
1620
SOLAR
PHOTOVOLTAIC PANELS
SOLAR PANELS AND GREEN ENERGY SYSTEMS
Powerhouse Distributions has launched a reliable,
high performance and high quality range of:
•Solar panels
•Solar charge controllers (MPPT)
•Pure and modified sinewave inverters
•Solar water pumps
•Wind turbines
•Deep cycle (solar) batteries.
SOLAR IN SOUTHERN AFRICA
In the past few years, the number of solar system installations
in Africa has grown at a tremendous rate. We at Powerhouse
Distribution strive to always come up with new ideas and be at
the forefront of the renewable energy sector. We stock a very
comprehensive range of solar products and equipment.
SOLAR PANELS
We have a high grade range of solar panels in the poly and
mono-crystalline range designed for high efficiency solar
systems. Our panels are available in 12V or 24V from 50W
up to and including 200W.
INVERTERS
Powerhouse only distributes the highest quality equipment and
our solar inverters are no exception. We offer units from 150W
up to and including 3000W in the pure sinewave and modified
sinewave range.
SOLAR CHARGE CONTROLLERS
Powerhouse has a comprehensive range of solar charge controllers
including the state of the art maximum power point tracking units
from AEC. These allow your solar panels to operate at their
optimum power output voltage, providing higher efficiency
up to 97% with lower power losses.
51
51
SOLAR
CHARGE CONTROLLERS
SUNMAX-1500W SOLAR MPPT CONTROLLER
GRID-TIE TOUGH INVERTER
The Sunmax-1500W developed by AEC can be used universally
for 12, 24, 36 and 48V. Its broad DC input voltage range makes
sensible system configuration possible for almost all PV modules.
Thanks to the integrated MPP tracking, the charger guarantees an
energy yield that is 15-30% higher than that of conventional shunt
and serial charge controllers.
•Pure sinewave output
•Microprocessor controlled to guarantee stable charging system
•Multiple operations: Grid tie, Off grid and grid-tie with backup
•LCD display panel for comrehensive information
•Multiple communications
•Built-in MPPT solar charger.
Auto-selection four-stage (Bulk/Pulse/Float1/Float2) charge mode
to reduce the charge time by a third and maximise the system’s
performance. What is unique about charge controllers of this power
range is the high protection class, and the broad temperature
range that makes worldwide use, even in harsh ambient conditions,
possible. The easy installation and completely automatic
customisation of the controller’s settings by the SA series
make its commissioning very simple.
Features:
Model
•Parallel capable
•MCU controlled
•LCD display
•High efficiency
•Battery temperature compensated
•Four-stage charging.
Model
Output Data (AC) Sunmax-1500W
Input
Rated Voltage
40-120Vdc
Current (Max.)
35A
Max. PV Array Open Circuit Voltage
150Vdc
Output
Nominal Battery Voltage
Max. Charger / Output Current
12/24/36/48Vdc
60A
Physical Characteristics
Dimensions (L x H x D, mm)
Input/Output Connectors
Weight (kg)
165 x 85 x 330
Hardwired
(Terminal Block)
3.2
Computer Interface
Type
Tough-5000
RS-232
Maximum AC Output
5000W
Maximum AC Output Current
22 a.c.A
Nominal AC Voltage
220-240 a.c.V
Grid AC Frequency
50/60Hz, auto-selection
Total Harmonic Distortion
AC connection / Grid forms
< 3%
TN-C, TN-S, TN-C-S
Input Data (DC)
Maximum DC Power
Maximum DC Input Current
Max. number of MPP Trackers
Maximum DC Voltage
5300W
2 x 15 d.c.A
2
650 d.c.V
MPP Tracking Voltage Range
150-500 d.c.V
Peak Power Tracking Voltage Range
200-460 d.c.V
Efficiency
MPPT Efficiency
Maximum Efficiency
Consumption: Operating
(standby) / Night
>99.9%
96.9%
<12.5W / <0.2W
General Specification Dimensions (W x H x D) in mm
Weight
Cooling Concept
Acoustic Noise Level
405 x 442 x 165
25.8kg
free convection
< 35dB(A)
Operating Temperature Range
-20 to +55 °C
Ambient Temperature Range
-25 to +60 °C
Humidity
Protection Degree
0 to 95%,
IP65
Features
DC Connection
AC Connection
Communication Interface
52
MC4, Tyco
AC connectors
RS232, RS485;
Bluetooth (Option)
ISOLATION TRANSFORMERS
1 PHASE & 3 PHASE
ISOLATION TRANSFORMER (10kVA-40kVA)
SPECIFICATIONS:
DESCRIPTION:
•Input Voltages: Single Phase 230V; Three phase 380, 400, 415V Delta
•Frequency:
48-63Hz; 0.95%
•Output Voltage:
Single Phase 230VAC;
Three Phase 400VAC Star
•Cooling:
Oil Cooled
•Application:Outdoor
•Nominal Power Range: From 10kVA 1P; From 20kVA
to 40kVA 3P
•Enclosing:
Weatherproof powder-coated
mild steel
•Vector Group:
Dyn 11
•Temperature Class:H
•Environment:
- Ambient 0-45°C;
- Humidity 0-95%;
- Altitude Max 3000m,
no die-rating
This interface transformer has been specifically designed for
use in Africa, where conditions vary from country to country and
site to site. The input of the transformer has an easily adjustable
tap changer, allowing for voltage variation of 380VAC ~ 415VAC
nominal. The output is designed to offer 400VAC as this is
the European standard, three phase voltage, of which 95% of
equipment manufactured in Europe and Southern Africa require.
The input winding has been designed to withstand high input
voltages, often found in African conditions, without experiencing
permanent damage. The overall transformer has been designed
to tolerate the type of harmonic distortion often associated with
non linear loads, like x-ray and telecommunications equipment.
The inter-winding screens offer high attenuation of interwinding
voltages and good common-mode and differential-mode protection
(0V between neutral and earth). Due to the delta primary, phase
shifting is eliminated.
The overall, oil-cooled packaging allows for outdoor installation.
This feature becomes handy when space and cooling in existing
installations are limited. Finally, because of the double wound
design and the electro-static screen, you have complete isolation
between primary and secondary, providing additional safety
between the installation and the uitility.
FEATURES:
•Interface Isolation Transformer designed for Harsh African
conditions
•Easily adjustable tap changer 380V-415V
•Withstands high input voltages
•For non-linear loads
•High attenuation of inter-winding voltages.
•Outdoor installation
•Complete Isolation between primary and secondary.
Model
Input/Output
Rating
Connection
Dimensions (W x H x D mm)
Weight
10kVA/IS
230/230
10kW
Stud
450 x 535 x 425
120kg
20kVA/IS
400/400
20kW
Stud
515 x 840 x 696
250kg
25kVA/IS
400/400
25kW
Stud
515 x 840 x 696
250kg
30kVA/IS
400/400
30kW
Stud
515 x 840 x 696
250kg
40kVA/IS
400/400
40kW
Stud
515 x 840 x 696
265kg
Note: Other ratings available on request
53
53
ACCESSORIES
SEALED & SEMI-SEALED BATTERIES
BATTERIES - SEALED MAINTENANCE FREE
Model
Design Life
Volts
Capacity at 20Hr Rate (Ah)
Dimensions (L x W x H) mm
Mass (kg)
2.0
12V7-5
3-5 years
12V
7.2Ah
151 x 65 x 100
12V17-5
3-5 years
12V
17Ah
181 x 77 x 167
5.3
12V24-5
3-5 years
12V
24Ah
166 x 175 x 125
7.6
12V33-10
10 years
12V
33Ah
195 x 130 x 168
9.7
12V45-10
10 years
12V
45Ah
197 x 166 x 170
14.6
12V65-10
10 years
12V
65Ah
350 x 167 x 179
22.4
12V100-10
10 years
12V
100Ah
330 x 171 x 222
29.0
Mass (kg)
BATTERIES - SEMI SEALED MAINTENANCE FREE
Volts
Capacity (Ah)
Dimensions (L x W x H) mm
12V36
Model
12V
36Ah
207 x 175 x 175
11.5
12V45
12V
45Ah
207x 175 x 175
12.1
12V55
12V
55Ah
242 x 175 x 190
14.1
12V66
12V
66Ah
277 x 175 x 175
16.4
12V88
12V
88Ah
381 x 175 x 190
19.5
12V102
12V
102Ah
330 x 175 x 240
26
* Other battery capacities available
54
ACCESSORIES
CABINETS & SNMP CARDS
SNMP CARDS
•Internal units to be used with UPS’s equipped with an intelligen slot
•External units to be used with UPS’s already equipped with RS232 communications
•Web server interface
•Linux, MAC and Windows compatible
•Remotely control UPS’s
•Battery management features for UPS’s being monitored
•SMS and Email capable for several UPS alarms and statuses
•Shut down multiple PC’s and/or servers during a power outage.
BATTERY CABINETS
•Used for all battery types
•In 7 different sizes, selection matrix below for battery size and cabinet sizing requirements.
No. of
Batteries
7.2Ah
8Ah
9Ah
12Ah
17Ah
20Ah
24Ah
28Ah
33Ah
45Ah
75Ah
100Ah
A1
6
6
6
4
4
4
2
3
2
2
1
1
A2
12
12
12
8
8
8
4
6
4
4
2
2
A4
24
24
24
16
20
20
8
12
12
8
4
4
A8
60
60
60
40
40
40
16
24
24
16
12
8
A12
90
90
90
60
60
60
24
36
36
24
18
12
A20
150
150
150
100
100
100
40
60
60
40
30
20
A35
270
270
270
180
180
180
80
110
105
70
50
35
55
55
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement