Apple | Cinema Display | Technical information | Apple Cinema Display Technical information

Apple Cinema Display Technical information
Apple Cinema Display
K Apple Computer, Inc.
© 1999 Apple Computer, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple.
Your rights to the software are governed by the accompanying software license agreement.
The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the
“keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may
constitute trademark infringement and unfair competition in violation of federal and state laws.
Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for
printing or clerical errors.
Apple Computer, Inc.
1 Infinite Loop
Cupertino, CA 95014-2084
408-996-1010
http://www.apple.com
Apple, the Apple logo, ColorSync, Mac, and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S.
and other countries.
Apple Cinema Display and Finder are trademarks of Apple Computer, Inc.
ENERGY STAR is a U.S.registered trademark.
PANTONE® and other Pantone, Inc. trademarks are the property of Pantone, Inc. Portions © Pantone, Inc. 1995.
VESA Display Data Channel (DDC) is a trademark of the Video Electronics Standards Association.
Simultaneously published in the United States and Canada.
Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a
recommendation. Apple assumes no responsibility with regard to the performance or use of these products.
5
6
7
9
10
11
11
Contents
About Your Apple Cinema Display
11
12
13
15
15
16
17
17
17
17
20
Congratulations!
Important Safety Instructions
Setting Up Your Apple Cinema Display
What’s Next
At a Glance
Installing the Apple Displays Software
About Your Apple Displays Software
Adjusting the Display
Finding Answers
Troubleshooting
Safety
Healthy Use of Your Computer Equipment
General Maintenance
Protecting Your Display From Theft
Do You Need to Install a Graphics Card?
Conserving Energy
Technical Information
Communications Regulation Information
3
Display
4
Software
Power adapter and cord
Cleaning cloth
Shipping cover
Manual and service
and support materials
Congratulations!
Your Apple Cinema Display™ is a 22-inch flat panel monitor that displays superb color
and graphics on a screen impressive for its size and clarity. Whether you use it for office
presentations, digital video editing in wide screen format, or editing dual page layouts for
print publishing, the display’s sleek and innovative design is sure to provide hours of
pleasurable viewing. And you’ll be able to set up and use your new display in just a few
easy steps.
About Your
Apple Cinema Display
5
Important Safety Instructions
m Turn off the computer before setting up your Apple Cinema Display. Leave the
computer plugged into a grounded power outlet.
m When lifting or carrying the display, grasp the edges. Do not lift the display by the
stand or cables.
m Don’t place books or other objects under the display to raise the display height or
change the viewing angle. Place the display on a flat and stable surface.
m Don’t press or put hard objects against the screen or lay the monitor screen down.
m Read all the setup instructions carefully before you plug your display into a power
source.
Don’t lift by the stand.
Don’t lift by the cable.
Lift here
6
Warning Use only the power adapter that came with your display. Adapters for other
computer equipment may look similar, but they may damage your display.
This equipment is intended to be electrically grounded. This is a safety feature. Your
power cord has a plug that has a third grounding pin; be sure to connect it only to a
grounded outlet. If you are unable to insert the plug into the outlet, contact a
licensed electrician to replace the outlet with a properly grounded outlet. Do not
defeat the purpose of the grounding plug!
If your power cord connects directly to the power socket on your computer, be sure
that the computer is grounded.
For additional safety information, see “Safety” on page 15.
Step 1: Set the display upright and extend the stand.
Push or pull here to
tilt the display to the
desired viewing angle.
Setting Up Your
Apple Cinema Display
Warning Your display is designed to tilt between 10˚ and 30˚ for proper viewing.
Be careful not to tilt the display so far forward that it falls.
7
Step 2: Plug in the display’s power adapter.
Step 3: Plug in the display’s DVI and USB connectors.
Plug the power adapter cord
into a grounded wall outlet
or power strip. (Some cords may
connect to the power socket in
the back of your computer.)
Plug the USB connector
into the computer here.
Plug the DVI connector
into the computer here.
Plug the
display’s
power cable into
the power adapter.
Although your graphics card may have two monitor ports, connect your Apple Cinema
Display to the Digital Visual Interface (DVI) port only.
Important
8
You can use only one monitor connected to your graphics card at a time.
Step 4: Connect a USB keyboard to the display, if
desired.
Step 5: Press the monitor power button.
Both your computer and monitor start up. After a few moments, the Macintosh desktop
appears on the screen.
If nothing appears or you see other problems, see “Troubleshooting” on page 13 for
more information.
How Do I Turn Off the Display?
Your monitor power button is preset to shut down or put to sleep both your monitor and
computer at the same time. Press the monitor power button again to start up or wake
the monitor and computer.
Connect your
USB keyboard here.
You can change the power button setting so that pressing the monitor power button
affects the monitor only. To change the power button setting, open the Monitors control
panel and change the power button setting in the Preferences section. For more
information about sleep settings and the Energy Saver or Monitors control panel, see
Mac Help.
What’s Next
Congratulations—you’ve finished setting up your display. Next, you need to install the
software that came with your display.
9
At a Glance
Brightness buttons
Power button
USB ports
Security ring
Power adapter cord
DVI connector
Power adapter
10
USB connector
Installing the Apple Displays Software
About Your Apple Displays Software
Make sure that you install the software from the Apple Displays Software CD
that came with your monitor.
The Apple Displays Software is a set of files that let you adjust basic picture and color
settings.
Important
To install the Apple Displays Software, follow these steps:
1
Insert the Apple Displays Software CD into your computer’s CD-ROM drive.
The CD icon appears on the desktop.
2
Double-click the CD icon.
The Apple Displays Software window opens.
3
Double-click the folder that contains the language you want to use.
4
Double-click the Apple Displays Software folder.
5
Double-click the Upgrader icon to start the installation program.
6
Follow the instructions on the screen until the installation is complete.
Note: During installation, you are presented with the terms of your software license
agreement. Please read the terms carefully before you agree.
The program checks to make sure you have the system software you need to use the
display. If anything is missing, a message tells you what you need. You won’t be able to
install the software until you correct the problem.
After the installation, you need to restart your computer.
7
Click Restart.
The software is now installed and the display is ready for use.
m The Monitors control panel lets you change the way your computer displays images.
The Monitors control panel is located in the Control Panels folder in the Apple (K)
menu. For help using the Monitors control panel, open the Help menu and choose
Show Balloons. For more information, open the Help menu and choose Mac Help.
m The Sound control panel lets you change the way your computer processes sound.
You can use it to set speaker volume, select input and output devices such as
microphones and speakers, and choose other settings such as alert sounds. The
Sound control panel is located in the Control Panels folder in the Apple (K) menu.
For more information, see Mac Help.
m The Control Strip lets you quickly adjust screen resolution and color depth. For help
using the Control Strip, see Mac Help.
m DigitalColor Meter (located in the Apple [K] menu) lets you obtain the RGB (red,
green, and blue) values your computer uses to create colors and specify these values
using other color systems. For help using DigitalColor Meter, click the Help button in
the upper-right corner of the DigitalColor Meter window.
m The PANTONE® Color Picker for Apple lets you specify PANTONE® values for colors
used in your documents in many application programs. In these applications, the
System Color Picker opens automatically when a new color needs to be specified. For
more information about using the PANTONE® Color Picker for Apple, see Mac Help.
m ColorSync is Apple’s unique color-matching software that ensures the colors you
input (using a scanner or camera) closely match the colors you see on your screen
and on the printed page. For help using ColorSync, see Mac Help.
11
Adjusting the Display
Finding Answers
You can adjust the monitor’s brightness by pressing the brightness buttons on the
display.
When you have questions about your display, there are several places to look for
answers.
You can calibrate the display and adjust additional settings using the Monitors control
panel. For more information about the Monitors control panel, choose Mac Help from
the Help menu.
In this manual
Use this manual to find out how to set up your display, install
the software, and find solutions to common problems.
In Mac Help
If you need help using the Apple Displays Software or adjusting
the display, open the Help menu and choose Mac Help. Type
the topic you want information about and click Search, or use
the table of contents to find your topic.
On the Internet
Apple maintains a number of sites on the World Wide Web that
provide product information, software updates, and technical
support information. You can view Apple’s home page at:
www.apple.com
Over the telephone
If you can’t find answers in any of the materials provided, call
the Apple Assistance Center. (See the service and support
information that came with this display.)
12
Troubleshooting
m Make sure the display cables are connected to your computer properly.
Check this section for solutions to problems you might experience with your display.
m Make sure the DVI display cable is connected securely.
If you have a problem with your display and nothing presented in this
manual solves it, consult the service and support information that came with your
display for instructions on how to contact an Apple-authorized service provider or
Apple for assistance. If you attempt to repair the display yourself, any damage you
may cause to the display will not be covered by the limited warranty on your display.
Contact an Apple-authorized dealer or service provider for additional information
about this or any other warranty question.
m Make sure your computer is not in sleep mode.
Warning
The light on the front of the monitor is flashing amber.
m Make sure the brightness is set properly. The brightness control (marked by ¤) is
under the right front edge of the display.
During installation of the Apple Displays Software, a message appears, “This
version of system software is not supported by the Apple Displays Software.”
m Make sure you’re using the latest version of the Mac OS.
m If this message appears in the Apple Displays Software Installer, make sure you select
the startup hard disk in the Installation dialog box.
The power light flashes amber when an error has been detected.
A message appears, “This monitor is not supported by this version of the Apple
Displays Software.”
m If you see a repeating sequence of three short flashes, the monitor is detecting input
in the wrong video format. Check that you have the correct graphics card installed
and that you’ve installed the correct monitor software.
m Make sure you have installed the Apple Displays Software that came with your display.
For installation instructions, see “Installing the Apple Displays Software” on page 11.
m If you see a sequence of two short flashes and a long flash, the monitor is detecting a
problem with a backlighting lamp. Contact an Apple-authorized dealer or service
provider for additional information about resolving the problem.
The screen image appears dim or flickers.
No image appears on the screen.
m Calibrate the monitor using the Calibrate option in the Monitors control panel.
m Make sure the display is turned on.
m The flickering could be caused by interference from a nearby power line, a fluorescent
light, or an electrical device—for example, a radio, a microwave oven, or another
computer. Try relocating nearby electrical devices, or moving your computer and
display.
m Make sure the computer is turned on.
m Make sure the power cord is plugged in properly.
m Adjust the brightness setting. The brightness control (marked by ¤) is under the
right front edge of the display.
If the display power cord is plugged into a grounded wall outlet or power strip,
check to see whether power to the outlet has been interrupted. You can test the
outlet by plugging in something that you know works—like a desk lamp or radio.
13
The screen image is blurry.
m Switch the resolution of the display using the Monitors control panel or the Control
Strip. It’s recommended that you choose the 1600 x 1024 resolution for best results.
Other resolutions may appear blurry because they are scaled to fit the monitor
screen size.
No colors appear on the screen or the colors don’t look right.
m Make sure the display cables are connected firmly to the correct ports on the
computer.
m You may want to calibrate your monitor using the Monitors control panel. For more
information on color and your display, see Mac Help.
m Open the Monitors control panel and check if your monitor is set to display grays.
For more information on color and your display, see Mac Help.
m Make sure you’ve installed the Apple Displays Software that came with your display.
For installation instructions, see “Installing the Apple Displays Software” on page 11.
Changes in the Monitors control panel don’t appear on the display.
m Each display connected to your computer has its own Monitors control panel. Use the
control panel with the name of your display in the window’s title bar.
m Make sure you have installed the Apple Displays Software that came with your display.
For installation instructions, see “Installing the Apple Displays Software” on page 11.
You don’t see an onscreen display when you press the brightness button, or you
don’t see power mode options in the Monitors control panel.
m Make sure you’ve connected the USB connector on the display cable to the USB port
on your computer. Some of the features of the Apple Displays Software require a USB
connection. For more information, see “Setting Up Your Apple Cinema Display” on
page 7.
After you change the screen resolution, desktop icons move.
m Changing the screen resolution affects the display of information on your screen.
The operating system may automatically reposition icons after you change the screen
resolution.
The screen freezes.
m If you are using both Energy Saver and a screen saver program, the screen saver
program may be conflicting with Energy Saver. Turn off either the screen saver
program or Energy Saver, and restart your computer.
The name of your display doesn’t appear in the title bar of the Monitors control
panel.
m Make sure the USB connector on the display cable is plugged directly into your
computer’s USB port.
14
m If the Apple Displays Software is installed and you start up your computer holding
down the Shift key to disable extensions, the software will not run. Restart your
computer without disabling extensions to use the software.
m Reinstall the software that came with your display. For installation instructions, see
“Installing the Apple Displays Software” on page 11.
When I press the monitor power button, the computer shuts down or goes to sleep.
m The monitor power button is preset to shut down or put to sleep both the monitor
and your computer. To change the monitor power button setting so that it affects the
monitor only, open the Monitors control panel and change the power button setting
in the Preferences section.
Safety
The only way to disconnect power completely is to unplug the power cord
from the computer or electrical outlet. Make sure at least one end of the power cord is
within easy reach so that you can unplug the display when you need to.
Important
Warning Never remove the case from the display or power adapter! You could come
in contact with hazardous voltage. Electrical equipment may be hazardous if misused.
Operation of this product, or similar products, must always be supervised by an adult.
Do not allow children access to the interior of any electrical product and do not
permit them to handle any cables.
Disconnect the power plug (by pulling the plug, not the cord) if any of the following
conditions exists:
m the power cord or plug becomes frayed or otherwise damaged
Healthy Use of Your Computer Equipment
m you spill something into the case
Use the following illustration to help you in positioning your monitor.
m your display is exposed to rain or any other excess moisture
m your display has been dropped or the case has been otherwise damaged
m you suspect that your display needs service or repair
m you want to clean the case or screen (use only the recommended procedures
described in “Cleaning the Screen and Case” on page 16)
Be sure that you always follow these instructions:
m Keep your display away from sources of liquids and moisture.
m Keep the display’s vents free from obstruction.
m Don’t hang anything on the display.
m Keep these instructions handy for reference by you and others.
45–70 cm (18–28 in.)
Shoulders
relaxed
Forearms and
hands in a
straight line
Forearms level
or tilted slightly
Lower back
supported
Thighs tilted
slightly
Top of the screen at or slightly
below eye level (You may need
to adjust the height of your
monitor by raising your
work surface.)
Screen positioned to avoid
reflected glare
Clearance under work surface
Feet flat on the floor
m Follow all instructions and warnings dealing with your system.
15
Here are some guidelines for adjusting the furniture in your work area to accommodate
your physical size and shape.
m An adjustable chair that provides firm, comfortable support is best. Adjust the height
of the chair so your thighs are horizontal and your feet flat on the floor. The back of
the chair should support your lower back (lumbar region). Follow the manufacturer's
instructions for adjusting the backrest to fit your body properly.
m When you use the computer keyboard, your shoulders should be relaxed. Your upper
arm and forearm should form an approximate right angle, with your wrist and hand in
roughly a straight line. Make sure the armrests of your chair don’t interfere with your
positioning. You may have to raise your chair so your forearms and hands are at the
proper angle to the keyboard. If this makes it impossible to rest your feet flat on the
floor, you can use a footrest with adjustable height and tilt to make up for any gap
between the floor and your feet. Or try lowering the desktop to eliminate the need for
a footrest. Another option is to use a desk with a keyboard tray that is lower than the
regular work surface.
For more health and safety information about your computer equipment, open Mac Help
from the Help menu when you’re in the Finder. You can also see the following (English
only) World Wide Web site:
www.apple.com/about/ergonomics
General Maintenance
To maintain your Apple Cinema Display and ensure its long life:
m Do not block the display’s vents.
m Do not let liquid get on or into the display.
m Do not press on the surface of the display screen.
m Do not write on the screen or touch the screen with a sharp object.
m Turn off your monitor when the computer is idle for a prolonged time.
m Position the mouse at the same height as your keyboard. Allow adequate space to use
the mouse comfortably to the immediate right or left.
m If you will not be using your display and computer for a day or more, turn off the
computer and display or use Energy Saver.
m Position the monitor directly in front of you with the keyboard directly in line with the
monitor. The best distance from your eyes to the screen is up to you, although most
people seem to prefer 18 to 28 inches (45 to 70 cm).
Important Using a screen saver program to prevent damage to your screen will reduce
the life span of the monitor backlighting feature.
m Position the monitor to minimize glare and reflections on the screen from overhead
lights and windows. Tilt the monitor to the best angle for viewing, helping to reduce
or eliminate glare from lighting sources you can’t move.
m Adjust the brightness of the screen to ensure the best image quality and viewing
comfort.
16
Cleaning the Screen and Case
Your Apple Cinema Display comes with a cleaning cloth for wiping it down. If you need
to clean the screen or case beyond wiping it down, follow these instructions:
1
Turn your computer and display off.
2
Disconnect the display’s power cord from the electrical outlet or power strip.
3
Disconnect the USB and DVI cables from the back of the computer.
4
Clean the screen with soft, lint-free paper or cloth dampened with mild soap and
water.
If you are not sure whether your computer or graphics card has the appropriate built-in
video capability, check with an Apple-authorized dealer.
Note: If you’re using more than one display, you may need a graphics card for each
display you are using.
Warning Do not spray liquid directly onto the display screen. Liquid could drip
inside the display and cause electrical shock.
Conserving Energy
5
Wipe the case surfaces lightly with a clean, soft cloth dampened with water.
Warning Don’t use alcohol, aerosol sprays, solvents, or abrasives that might damage
the finish on the case.
Protecting Your Display From Theft
You can connect a security lock and a narrow, flexible cable through the security ring
on the display cable to secure your display to your computer and prevent theft (see “At a
Glance” on page 10). Security locks are available from an Apple-authorized dealer or
computer retailer.
You can use the Energy Saver control panel to set your monitor to conserve energy after
a specified period of inactivity. When the Energy Saver detects that you’re not using the
computer, it darkens the monitor screen and reduces the amount of energy it consumes.
To wake up the monitor, press any key on the keyboard. For more information about
using Energy Saver, choose Mac Help from the Help menu in the Finder. Also see the
documents in the TCO Information folder, located on the CD that came with your
monitor, and see ENERGY STAR compliance information in “Power-Saving and
Environmental Features” on page 18.
®
Technical Information
Screen
Do You Need to Install a Graphics Card?
Your Apple Cinema Display works with a graphics card with a DVI digital-only connector.
If your computer doesn’t have the required graphics card, you must install one to use
this display.
m 22-inch (558.5 millimeters [mm]) viewable diagonal image, 18.5 inches (470.4 mm)
horizontal by 11.6 inches (301.1 mm) vertical
m 1600 (horizontal) x 1024 (vertical) active pixels
m Color depth: 24-bit color
Desktop Stand
m Tilt adjustment: 10˚ to 30˚
17
Weight
Power-Saving and Environmental Features
m Display: 25 pounds (11.34 kilograms)
The color of the power indicator light on the front of the monitor indicates the operating
mode:
m Power supply: 14 ounces (398 grams)
Display Dimensions
m Height: 18.9 inches (in.) (479 mm)
m Width: 23.1 in. (588 mm)
m Depth (with stand extended from 10˚ to 30˚ viewing angle): 8.27 in. (210 mm) to
12.17 in. (309 mm)
Power mode
Power indicator
Power consumption
Mac OS
Energy Saver mode
On
Green
<62 W
Normal
Standby/Suspend
Amber
<5 W
Monitor sleep
Off
Off
<5 W
System sleep
Temperature
m Operating: 50˚ to 95˚ F (10˚ to 35˚ C)
m Storage (up to 6 months): –40˚ to 116˚ F (–40˚ to 47˚ C)
m Shipping (up to 72 hours): –40˚ to 149˚ F (–40˚ to 65˚ C)
Humidity (Noncondensing)
m Operating: 20% to 80%
m Storage (up to 6 months): 20% to 80%
m Shipping (up to 72 hours): 20% to 80%
Altitude
m Operating: 0 to 10,000 feet (ft.) (0 to 3,030 meters [m])
m Shipping: 0 to 35,000 ft. (0 to 10,606 m)
18
For instructions on adjusting the system and display sleep settings and additional energyconservation information, see Mac Help.
m TCO/NUTEK: This product has been certified by TCO (the Swedish Confederation of
Professional Employees) to meet the standards for ergonomics, energy efficiency
(NUTEK), emissions, and ecology.
m MPR II: This product meets the strict limits for reduced electromagnetic and
electrostatic emissions.
m ENERGY STAR:® As an ENERGY STAR® partner, Apple Computer has determined that
this product meets the ENERGY STAR® guidelines for energy efficiency. The United
States Environmental Protection Agency’s ENERGY STAR® program is a partnership
with office product equipment manufacturers to promote energy-efficiency. Reducing
energy consumption of office products saves money and reduces pollution by
eliminating wasted energy.
Active Video Image Area
Power Adapter Electrical Requirements
The recommended resolution for your monitor is 1600 x 1024 dots per inch. You can
choose other standard resolutions that are scaled to fit your monitor’s screen size. You
can use the Monitors control panel to choose standard resolutions for your monitor. The
resolutions supported for computer input are shown in the following table:
m Input: 100–240 volts ( V ), AC 50–60 hertz (Hz)
Input resolution
Output image size from scaler
m Two self-powered USB ports supporting USB input devices
640 x 480
800 x 600
1224 x 768
1360 x 1020
1360 x 1020
1360 x 1020
m VESA Display Data Channel (DDC)™ Standard: This display supports VESA DDC 2B.
1280 x 1024
1280 x 1024
m Digital Visual Interface connector (DVI) digital-only type connector
800 x 500
1024 x 640
1280 x 800
1600 x 1000
1600 x 1000
1600 x 1000
800 x 512
640 x 480 (stretched)
800 x 600 (stretched)
1024 x 768 (stretched)
1600 x 1024
1600 x 1024
1600 x 1024
1600 x 1024
1600 x 1024
1600 x 1024
Note: The number of resolutions that your computer supports may be different from
those listed here. Your computer may not support all resolutions.
m Output: 16V DC at 3.875A
Interfaces
Display Cable Specifications
The digital-only connector contains 24 signal contacts organized in three rows of eight
contacts.
Pin Signal assignment
Pin
Signal assignment
Pin
Signal assignment
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
TMDS Data1–
TMDS Data1+
TMDS Data1 Shield
No connect
No connect
+5 V Power
Ground (for +5 V )
Hot Plug Detect
17
18
19
20
21
22
23
24
TMDS Data0
TMDS Data0+
TMDS Data0 Shield
No connect
No connect
TMDS Clock Shield
TMDS Clock+
TMDS Clock–
TMDS Data2 –
TMDS Data2+
TMDS Data2 Shield
No connect
No connect
DDC Clock
DDC Data
No Connect
19
Communications Regulation Information
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the
specifications in Part 15 of FCC rules. See instructions if interference to radio or television reception is suspected.
Radio and Television Interference
The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and
used properly—that is, in strict accordance with Apple’s instructions—it may cause interference with radio and television
reception.
This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the
specifications in Part 15 of FCC rules. These specifications are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a particular
installation.
You can determine whether your computer system is causing interference by turning it off. If the interference stops, it was
probably caused by the computer or one of the peripheral devices.
If your computer system does cause interference to radio or television reception, try to correct the interference by using
one or more of the following measures:
m Turn the television or radio antenna until the interference stops.
m Move the computer to one side or the other of the television or radio.
m Move the computer farther away from the television or radio.
m Plug the computer into an outlet that is on a different circuit from the television or radio. (That is, make certain the
computer and the television or radio are on circuits controlled by different circuit breakers or fuses.)
If necessary, consult an Apple-authorized service provider or Apple. See the service and support information that came
with your Apple product. Or, consult an experienced radio/television technician for additional suggestions.
Important Changes or modifications to this product not authorized by Apple Computer, Inc., could void the FCC
Certification and negate your authority to operate the product.
20
This product was tested for FCC compliance under conditions that included the use of Apple peripheral devices and Apple
shielded cables and connectors between system components. It is important that you use Apple peripheral devices and
shielded cables and connectors between system components to reduce the possibility of causing interference to radios,
television sets, and other electronic devices. You can obtain Apple peripheral devices and the proper shielded cables and
connectors through an Apple-authorized dealer. For non-Apple peripheral devices, contact the manufacturer or dealer for
assistance.
Responsible party (contact for FCC matters only): Apple Computer, Inc., Product Compliance, 1 Infinite Loop M/S 26-A,
Cupertino, CA 95014-2084, 408-974-2000.
Industry Canada Statement
This Class B device meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil
numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
VCCI Class 2 Statement
www.apple.com
034-0876-A
Printed in Korea
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising