C-more 6-inch Micro Quick Start Guide

C-more 6-inch Micro Quick Start Guide
Safety Information
®
WARNING: To minimize the risk of potential safety problems, you should follow all applicable
local and national codes that regulate the installation and operation of your equipment. These
codes vary from area to area and it is your responsibility to determine which codes should be
followed, and to verify that the equipment, installation, and operation are in compliance with the
latest revision of these codes.
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860
Quick Start Guide
Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes
and standards. We do not guarantee the products described in this publication are suitable for your
particular application, nor do we assume any responsibility for your product design, installation, or
operation.
C-more 6” Micro-Graphic Panels, Accessories & Replacement Parts
If you have any questions concerning the installation or operation of this equipment, or if you need
additional information, please call us at 1-800-633-0405 or 770-844-4200.
4
8
Install C-more 6” Micro-Graphic Panel
To access the Setup Menu of the panel’s setup
screens, press the the BAK [F1] and ENT [F5]
function keys simultaneously for three (3) seconds.
Panel Cutout (all models)
The C-more 6” Micro-Graphic panel can be
mounted through a cutout in an enclosure by using
the template provided with the panel, or using the
dimensions shown. The optional keypad bezels also
include templates. The enclosure mounting thickness
range for the panels and the keypad bezels is
0.04”–0.2” [1–5 mm]. Mounting screw torque is 2128 oz-in [0.15-0.2 Nm].
Landscape cutout shown
+0.04
6.339 –0.00
+1
161.0 –0
0.256
[6.5]
0.260
[6.6]
2. Setting
CUTOUT
OUTLINE
+0.04
4.811 –0.00
BEZEL
OUTLINE
CUTOUT
*NOTE: C-more Micro-Graphic panels with the letter “W” in the part number designate units with
5 selectable background colors of White, Pink1, Pink2, Pink3 and Red. Part numbers without the
letter “W” are provided with 5 selectable background colors of Green, Red, Amber, Yellow and Lime.
Examples
NOTE: Software and Firmware Version 2.0 or later is required with models EA1-S6ML and
EA1-S6MLW. Available for free download at www.automationdirect.com.
1
MODEL:EA1-S6ML
LISTED
7M17
IND.CONT.EQ.
Following are the minimum system requirements for running C-more Micro-Graphic Programming
Software, EA-MG-PGMSW, on a PC:
Product Label
NOTE: C-more 6” Micro-Graphic panels with hardware version R05 and higher must use firmware
version 3.20 or higher
The C-more 6” Micro-Graphic panel has a 5.7-inch STN LCD monochrome 320 x 240 dot display. Model
EA1-S6ML has five selectable LED-driven backlight colors including Green, Red, Amber, Yellow and Lime.
Model EA1-S6MLW has five selectable LED-driven backlight colors including White, Pink1, Pink2, Pink3
and Red. Both models feature five user-defined function keys, each key with a user-defined red LED indicator. The panels can display up to 40 lines by 80 characters of static text and up to 40 lines by 40 characters of dynamic text with embedded variables and phrases mixed with graphics at landscape orientation.
Portrait orientation can display 60 characters and 53 lines of static text and 40 lines by 40 characters of
dynamic text. Each model is rated UL for use on a flat surface of Type 1, 4X enclosure (indoor use only). The
C-more 6” Micro-Graphic panels are powered from a 12-24 VDC power supply or can operate in low-power
mode when powered from the serial communications port of select AutomationDirect PLCs.
Other features include:
2
NOTE: Install C-more Micro-Graphic
Programming software before connecting
the panel to the PC to ensure the panel
drivers install correctly.
Install Optional Hardware Accessories (sold separately)
2. Use the (4) Panel Mounting
Clips that are supplied with
the panel, to secure panel to
keypad bezel and compress
the gasket between the
panel and the keypad bezel.
Tighten screws to a torque
of 21-28 oz-in [0.15-0.2 Nm].
Connect C-more Micro-Graphic Panel to Computer
Cable Description
Use an EA-MG-PGM-CBL, USB to RS-232 Programming Cable Assembly, from a USB port type A on the
project development PC, through the supplied converter, to the RJ12 RS-232 programming/PLC serial
communications port on the C-more Micro-Graphic panel as shown below.
C-more 6 Inch
Micro-Graphic
Panel
• Inspect all equipment for completeness. If anything is missing
or damaged, immediately call the AutomationDirect returns
department @ 1-800-633-0405.
General Description
Choose C-more 6” Micro-Graphic Panel to PLC Protocols
& Cables
PLC Drivers
• CD-ROM or DVD drive for installing software from the CD, or internet access to download free programming software
6
3. Use (8) Bezel Mounting Clips to
secure keypad bezel through
enclosure cutout. Tighten screws
to a torque of 21-28 oz-in
[0.15-0.2 Nm].
USB to RS-232
Programming Cable Assembly
PC to Panel Programming
Cable Assembly
(Includes serial & USB cables)
EA-MG-PGM-CBL
USB
Cable
Serial
Cable
Function
Key Label
Insert
Serial - port1 or port2
Serial - port2 only
AutomationDirect Productivity3000
AutomationDirect CLICK
AuomationDirect Do-more
AutomationDirect K-sequence
AutomationDirect DirectNET
AutomationDirect SOLO
AutomationDirect GS Drives
AutomationDirect Modbus
Modicon Modbus RTU
Entivity Modbus RTU
Allen-Bradley DF1 Full Duplex
Allen-Bradley DF1 Half Duplex
Allen-Bradley PLC5 DF1
Allen-Bradley DH485
GE SNPX (90/30, 90/70, Micro 90, VersaMax Micro)
Mitsubishi FX
Mitsubishi Q and QnA
Omron Host Link (C200 Adapter, C500)
Omron FINS Serial (CJ1, CS1)
Siemens PPI (S7-200 CPU)
AutomationDirect SOLO Temperature Controller
AutomationDirect GS Drives
Cable Part No.
Shown is an example of a
C-more 6” Micro-Graphic
panel being assembled with
an optional 20-button
Keypad Bezel.
• Built in RJ12 serial communications port (RS-232)
• Adjustable contrast
• 2 optional keypad bezels, 20-button landscape and 21-button portrait mount
• Optional replaceable clear screen overlay
1. Remove
Expansion
Connector
Protective
Cover from
rear of
panel.
Cables used with serial Port2
AutomationDirect Productivity Series, Do-more,
CLICK, Direct LOGIC PLC RJ-12 port, DL05, DL06,
DV-1000CBL
DL105, DL205, D3-350, D4-450 & H2-WinPLC
(RS-232C)
Note: The PLC can provide 5 VDC through this cable. No external 12-24
VDC souce is required, however, screen brightness is diminished and
the alarm beep will not function.
Direct LOGIC DL405 PLC 15-pin D-sub
port, DL405
D4-1000CBL
(RS-232C)
Direct LOGIC (VGA Style) 15-pin port,
DL06, D2-250 (250-1), D2-260
FA-15HD
(RS-232C)
Use with DV-1000CBL cable.
Direct LOGIC PLC 15-pin D-sub port,
DL405
FA-CABKIT
(RS-232C).
Direct LOGIC PLC RJ-11 port, D3-340
OP-3CBL-1
(RS-232C).
AutomationDirect Productivity Series Do-more,
CLICK, Direct LOGIC PLC RJ-12 port, DL05, DL06,
DL105, DL205, D3-350, D4-450 & H2-WinPLC
(RS-232C)
Direct LOGIC (VGA Style) 15-pin port,
DL06, D2-250 (250-1), D2-260
(RS-232C).
Direct LOGIC PLC RJ-11 port, D3-340
(RS-232C).
Direct LOGIC DL405 PLC 15-pin D-sub
port, DL405 (RS-232C).
Direct LOGIC PLC 25-pin D-sub port,
DL405, D3-350, DL305 DCU and all DCM’s
(RS-232C).
Allen-Bradley MicroLogix 1000, 1100,
1200 & 1500 (RS-232C)
Allen-Bradley SLC 5-03/04/05,
ControlLogix, CompactLogix, FlexLogix
DF1 port (RS-232C)
Allen-Bradley PLC-5 DF1 port
(RS-232C)
Allen-Bradley MicroLogix, SLC 5-01/02/03,
DH485 port (RS-232C)
GE 90/30, 90/70, Micro 90, Versamax Micro
(Port2) 15-pin D-sub port
(RS-422A)
MITSUBISHI FX Series 25-pin port
(RS-422A)
MITSUBISHI FX Series 8-pin mini-DIN
(RS-422A)
OMRON Host Link (C200 Adapter, C500)
(RS-232C)
• Up to 999 screens, limited only by memory usage
20 Button
Keypad Bezel
EA-MG6-BZ2
4. Peel Protective Film
from front of panel.
• 0 to 50 °C (32 to 122 °F) operating temperature range
7
NOTE: Mounting clips for the
panel or keypad bezel are
included with each product
USB to RS232 Programming
Cable Assembly
Programming Software
3
Become Familiar with Available Communication Ports
The C-more 6” Micro-Graphic panels include a built-in RJ12 serial communications port (RS-232) used to
communicate with a PC during project development and later as a PLC communications interface. There is
also a second 15-pin RS-232/RS-422/RS-485 port for communications to a PLC.
NOTE: Free download of the
C-more Micro-Graphic
programming software at the
AutomationDirect web site.
EA-MG-PGMSW
Pin
RJ12 serial
communications Port1
Expansion
Connector
Signal
1
Logic GND
2
not used
3
EA-MG-PGM-CBL
RXD (232C)
4
TXD (232C)
5
Receives 5VDC
6
Logic GND
Agency Approvals
R01. 1 2 3 4 5
MODEL:EA1-S6MLW
R
C-more Micro-Graphic Panels
& Accessories
UL/CUL
E157382
C
UL508
UL
R
E157382
CSA
234884
CE
ISO-9000
EN61131-2
US
Copyright 2015, Automationdirect.com Incorporated/All Rights Reserved Worldwide
Yes
INPUT:12-24V 6.5W
Date code:****
MADE IN CHINA
LISTED
7M17
IND.CONT.EQ.
EA1-S6MLW + serial number
8
1
15
9
3). Optionally, the C-more 6” Micro-Graphic panel can be
powered in Low-Power mode* from most AutomationDirect
PLC’s RJ12 serial communications port by using a
DV-1000CBL communications cable, or a DV-1000CBL
communications cable with a FA-15HD 15-pin HD
DSub/RJ12 Adapter connected to an AutomationDirect
PLC’s 15-pin HD communications port (DL06, D2-250-1 &
D2-260) PLCs. See Chapter 6: PLC Communications in the
Hardware User Manual (EA6-USER-M) for additional
details.
Power supply wire connection
Pin
Signal
Pin
1
Frame GND
6
LE
Signal
Pin
11 TXD+ (422/485)
Signal
2
TXD (232C)
7
CTS (232C)
12 TXD– (422/485)
3
RXD (232C)
8
RTS (232C)
13 Term. Resistor
4
Supplies +5VDC
9
RXD+ (422/485)
14 do not use
5
Logic GND
10 RXD– (422/485)
15 do not use
1.7 lb-in (0.2 Nm)
Cable Part No.
EA-2CBL
EA-2CBL-1
EA-3CBL
EA-4CBL-1
EA-4CBL-2
EA-MLOGIX-CBL
EA-SLC-232-CBL
EA-PLC5-232-CBL
EA-DH485-CBL
EA-90-30-CBL
EA-MITSU-CBL
EA-MITSU-CBL-1
EA-OMRON-CBL
Connect C-more 6” Micro-Graphic Panel to PLC
Connect the serial communications cable between the C-more Micro-Graphic panel and the PLC. The
panel can be connected to the PLC via the panel’s built-in RJ12 serial communications port (RS-232) or
15-pin serial communications port with either RS-232, RS-422 or RS-485 communications.
C-more 6 Inch
Micro-Graphic
Panel
2). The C-more 6” Micro-Graphic panel is powered during
programming from the PC through the USB to RS-232
Programming Cable Assembly, EA-MG-PGM-CBL. When
powered from the PC, the panel will operate in Low-Power
mode.
Tightening Torque
RS-232
Name
Provide Power to the C-more 6” Micro-Graphic Panel
CLICK PLC
Supply to Panel:
1 A @ 12 - 24 VDC
(10.8 - 26.4 VDC)
R01. 1 2 3 4 5
R
LISTED
7M17
IND.CONT.EQ.
EA1-S6MLW + serial number
Equipment
Ground
GND
8
1
15
9
Recommended
DC Supply Fuse
750 mA fast acting,
ADC p/n AGC-75
–
+
Port 1
Required Wire Specification
Wire Material
Wire Size
Port 1
MODEL:EA1-S6MLW
INPUT:12-24V 6.5W
Date code:****
MADE IN CHINA
Supported temperature
PLC 15-pin serial
communications Port2
UL/CUL/CSA/CE Certification Numbers
10
1). The panel should be powered by a 1 Amp @ 12-24 VDC
class 2 power source in normal operation.
6 5 4 3 2 1
Programming Software & Programming Cable (sold separately)
C-more 6 inch
Micro Graphic
Panel
User PC
C-more 6 Inch
Micro-Graphic Panel
• UL, cUL & CE agency approvals (see below for details)
• 2-year warranty from date of purchase
NOTE: For the latest list of available
PLC drivers and PLC cables go to
www.automationdirect.com.
USB to RS232
Converter
• Built in Alarm Control setup that activates beep, backlight flash, customized alarm banner, and red LED blinking
Cable Description
Cables used with serial Port1
• 1792 KB memory
• Built in 15-pin serial communications port (RS-232/422/485)
Do you want to exit from System Screen?
No[F1] / Yes[F5]
4. Exit
• USB port to use with an EA-MG-PGM-CBL, USB to RS232 Programming Cable Assembly for project transfer from the
programming software to the panel
• Unpack any accessories that have been ordered, such as:
Keypad Bezel, DC Power Supply, programming cable,
communications cable, etc.
2. Serial Port2 – Loop Back Test
5. Touch Panel Test
• 150 MB free hard-disk space
Cutout
Template
1. Serial Port1 – Loop Back Test
4. Buzzer Test
UP
• Super VGA color video adapter and monitor with at least 800 x 600 pixels resolution
(1024 x 768 pixels recommended) 64K color minimum
DC Power
Connector
• C-more 6” Micro-Graphic panel
• cutout template
• mounting clips
• gasket
• function key label inserts
• Quick Start Guide
• DC Power Connector
EA1-S6MLW + serial number
9
8. Rotation
3. PLC Enquiry Test
ENT
• Keyboard and Mouse or compatible pointing device
Mounting
Clips
Function Key
Label Inserts
>
>
>
>
ENT
NOTE: Software and Firmware Version 2.0 or later is required with models EA1-S6ML and
EA1-S6MLW. Available for free download at www.automationdirect.com.
Unpack and Inspect
• Unpack the C-more Micro-Graphic panel from its shipping
carton. Included in the carton are the following:
R
Product Package Label
1808802 Bytes
BAK
1. Information
2. Setting
3. Test Menu
4. Exit
• Operating System - Windows® XP Home / Professional Edition Service Pack 2, Windows® 2000 with Service Pack 4,
Windows® Vista (32 or 64 bit), Windows® 7 (32 or 64 bit) or Windows 8 (32 or 64 bit)
INPUT:12-24V 6.5W
Date code:****
MADE IN CHINA
3. Test Menu
26206 Bytes
SETUP MENU
Install the Software and Develop a Project
• Communications Cable (serial) – to connect the C-more Micro-Graphic panel to your controller
R05. 1 2 3 4 5
1835008 Bytes
DWN
• Power source – An external 12-24 VDC power source is required for normal High-Power operation.
Recommended power supplies are AutomationDirect part numbers PSC-24-015 or PSC-24-030.
2. Backlight
7. Hourglass
• C-more 6” Micro-Graphic panel
• Personal computer – to run the C-more Micro-Graphic programming software
Hardware Version
Total:
Free:
• C-more Micro-Graphic USB to RS232 Programming Cable Assembly EA-MG-PGM-CBL, used to connect
between a PC and the Micro-Graphic panel’s built-in serial port. The panel will operate in Low-Power mode
when powered by the PC and the screen brightness is diminished.
1. LCD Contrast
6. Reset to Factory Default
BAK
Minimum items required to create a working system:
5
4. Versions
5. Clear User Memory
MEMORY
Usage:
• C-more Micro-Graphic Programming Software EA-MG-PGMSW (Downloadable version available from the
AutomationDirect web site at no charge.)
2. Protocol
4. Calibration
From the Setup Menu, information about the panel
can be obtained, settings can be adjusted, and panel
functions can be tested.
0.260
[6.6]
Before you begin...
EA1-S6MLW
shown in Portrait (Vertical) mode
1. Memory
3. Beep
ENCLOSURE MOUNTING
THICKNESS RANGE
0.04” - 0.2” [1 - 5mm]
EA1-S6ML
shown in Landscape (Horizontal) mode
1. Information
3. Extensions
R .118 [R3]
Enclosure Thickness
Menu flow Chart
Setup Menu
0.256
[6.5]
+1
122.2 –0
This publication is based on information available at the time it was printed. At
Automationdirect.com® we constantly strive to improve our products and services, so we reserve
the right to make changes to the products and/or publications at any time without notice and
without obligation. This publication may also discuss features that may not be available in certain
revisions of the product.
Accessing the C-more Micro-Graphic Panel Setup Screens
Over 60 °C
Copper
16 - 22 AWG
*NOTE: When the panel is powered through Port1 from a connected PLC or PC, the screen brightness
is diminished because the panel is running in Low-Power Mode. For full brightness, connect an
external 12-24 VDC power source to the panel’s power connection. Low-Power Mode should be
used during initial programming only. Connect an external 12-24 VDC power source when the
panel is installed in its application.
RS-232/422/485
NOTE: Recommended DC power supply to power the C-more Micro-Graphic Panel, AutomationDirect
Part No. PSC-24-015 or PSC-24-030.
DV-1000CBL
serial cable
*NOTE: When the panel is powered through Port1 from a connected PLC or PC, the screen brightness
is diminished because the panel is running in Low-Power Mode. For full brightness, connect an
external 12-24 VDC power source to the panel’s power connection. Low-Power Mode should be
used during initial programming only. Connect an external 12-24 VDC power source when the
panel is installed in its application.
Additional Help and Support
• For product support, specifications, and installation troubleshooting, a Hardware User Manual can be downloaded from
the On-line Documentation area of the AutomationDirect web site or purchased through the AutomationDirect Sales
team @ 1-800-633-0405 as part number EA1-MG6-USER-M.
• For software programming help, refer to the C-more Micro-Graphic Programming Software on-line embedded help.
• Refer to demos of the product at: www.CmoreMicro.com/software/software_demo.html
• For additional technical support and questions, call our Technical Support team @ 1-800-633-0405 or 770-844-4200.
C-more 6” Micro-Graphic Panel Specifications
Specifications
320 x 240 dots LCD display (Landscape Mode),
five user defined keypad function buttons, and five user defined LED's
6.295
[159.9]
Low Power Mode*
Red –> 10 nits
Red –> 50 nits
Green –> 11 nits
Green –> 125 nits
White –> 13 nits
White –> 150 nits
4.614” (W) x 3.480” (H) [117.2 mm x 88.4 mm]
4.535” (W) x 3.400” (H) [115.2 mm x 86.4 mm]
Adjusted from the panel’s built-in configuration setup menu
3, 9 o’clock axis –> 45 degrees
6 o’clock axis –> 40 degrees
12 o’clock axis –> 20 degrees
Push Button, Switch, Indicator Button, Indicator Light, Graphic Indicator Light, Numeric Display, Numeric
Entry, Inc/Dec Value, Bar Graph, Bitmap Button, Static Bitmap, Dynamic Bitmap, Recipe Button, Static Text,
Lookup Text, Dynamic Text, Screen Change Push Button, Screen Selector, Adjust Contrast, Function, Key
Configuration Object, Real Time Graphics Line Graph, Analog Meter.
• Maximum Inrush Current
• Acceptable External
Power Drop Duration
Environmental:
• Operating Temperature
• Storage Temperature
• Humidity
• Environmental Air
• Vibration
• Shock
• Noise Immunity
• Enclosure
• Agency Approvals
Physical:
5.0 VDC (4.75 – 5.25 VDC)
Supplied through the panel’s RJ12 serial communications port connection when used with most
AutomationDirect PLCs having a RJ12 communication port or from a PC USB.
1.05 W @ 5 VDC (210 mA)
No fuse required when directly connected to a PLC
or PC with recommended cable.
1 A for 500 µs
12/24 VDC (10.2 – 26.4 VDC)
MOUNTING CLIP
(8) places
1.695
[43.1]
6
1
2
3
+/-
0
Units: inches [mm]
Communication Port Adapters
0.333
[8.5]
D-SUB 15-pin 90-degree Communication Port Adapter (EA-ADPTR-4)
The EA-ADPTR-4 adapter plugs into the 15-pin serial port on the rear of
the 6” panel to allow a PLC communication cable to be plugged in at a 90
degree angle to reduce panel depth requirements. 15-pin straight through
pin-out. UL Recognized.
EA-ADPTR-4
GASKET
MOUNTING CLIP
(8) places
2.094
[53.2]
Esc
Menu
CLR
7
8
9
4
5
6
1
2
3
+/-
0
1.882
[47.8]
0.394
[10.0]
Four directional
cursor buttons,
numeric buttons and
ESC, MENU, CLEAR
and ENTER buttons.
Esc
7
8
9
Menu
4
5
6
3
CLR
1
2
Enter
+/-
0
Date code
Country of Origin
1.695
[43.1]IOIOI – PLC
KOYO ELECTRONICS INDUSTRIES CO., LTD.
EA-ADPTR-4
1.873
[47.6]
0.793
[20.2]
Part Number:
General:
• Micro-Graphic
Panels Supported
• Connection
• Power Consumption
• Keypad Button Life
Units: inches [mm]
The EA-COMCON-3 adapter plugs into the 15-pin serial port on the rear of
the 6”panel to allow wire terminal connections for an RS-422/RS-485/DH-485
PLC communication cable. UL Recognized.
EA-COMCON-3
0.687
[17.5]
10.000
[254.0]
9.195
[233.5]
ENCLOSURE MOUNTING
THICKNESS RANGE
0.04” - 0.2” [1 - 5mm]
Units: inches [mm]
• Storage Temperature
• Humidity
• Environmental air
Date code
KOYO ELECTRONICS INDUSTRIES CO., LTD.
8
9
Menu
4
5
6
CLR
1
2
3
Enter
+/-
0
Esc
7
Enter
Panel Thickness
GND
USB to RS232 Programming Cable Assembly
Note: The C-more 6” Micro-Graphic panel is installed into the keypad bezel using the
(4) mounting clips, EA-MG-BZ2-BRK, that are supplied with the panel.
0 to 50 °C (32 to 122 °F)
Maximum surrounding air temperature rating 50 °C
-20 to 60 °C (-4 to 140 °F)
5 to 95 % RH (non-condensing)
For use in Pollution Degree 2 environment
• Enclosure
• Agency Approvals
Physical:
CE (EN61131-2), UL508, CUL Canadian C22.2 No. 142-M95, UL File E157382
• Dimensions
10.000” (W) x 6.394” (H) x 2.488” (D)
[254.0 mm x 162.4 mm x 63.2 mm]
For use on a flat surface of Type 1, 4X enclosure (for indoor use only)
26.1 oz. [740 g]
USB to RS232 Converter Specifications
Part Number:
Customizing the Function Keys Label Insert
• USB Interface
Step 1 - Remove existing
function key label insert
using a small tool such as
jeweler’s screw driver.
• Serial Interface
USB Specification Rev. 1.1
Connector: USB Type B jack to accept USB Type B cable plug
RS232 (EIA-232-E)
Connector: RJ12 phone jack 6p to accept RJ12 cable plug
115.2 kbps Maximum
5 VDC (Supplied thru serial interface cable.)
50 mA (Does not include power to panel and/or bezel.)
• Baud Rate
• Input Voltage
• Power Consumption
Accessory Cables:
USB Type A plug to PC on one end, USB Type B plug to converter on other end, 0.30 m [1 foot] length (* Note)
• USB Cable
DV-1000CBL cable with RJ12 phone plug connectors on both ends, 2.0 m [6.56 feet] length (* Note)
• Serial Cable
Physical:
Part Number
None
Minimum of 500,000 cycles
(8) mounting clips, EA-MG-BZ2-BRK, included.
• Enclosure Mounting
Note: The C-more 6” Micro-Graphic panel is installed into the keypad bezel using the
(4) mounting clips, EA-MG-BZ2-BRK, that are supplied with the panel.
Environmental:
0 to 50 °C (32 to 122 °F)
Maximum surrounding air temperature rating 50 °C
-20 to 60 °C (-4 to 140 °F)
• Operating Temperature
• Storage Temperature
• Humidity
• Environmental air
• Vibration
• Shock
• Enclosure
• Agency Approvals
Physical:
5 to 95 % RH (non-condensing)
For use in Pollution Degree 2 environment
IEC60068-2-6 (Test Fc), 5-9 Hz: 3.5 mm amplitude, 9-150 Hz: 1.0G, sweeping, at a rate of
1 octave/min. (±10%), 10 sweep cycles per axis on each of 3 mutually perpendicular axes
IEC60068-2-27 (Test Ea), 15 G peak, 11 ms duration, three shocks in each direction
per axis, on 3 mutually perpendicular axes (total of 18 shocks)
NEMA ICS3-304
RFI, (145 MHz, 440 Mhz 10 W @ 10 cm)
Impulse 1000 V @ 1 µs pulse
For use on a flat surface of Type 1, 4X enclosure (for indoor use only)
CE (EN61131-2), UL508, CUL Canadian C22.2 No. 142-M95, UL File E157382
Replacement mounting gasket for C-more 6” Micro-Graphic keypad bezels EA-MG6-BZ2 and EA-MG6-BZ2P
EA-MG-S6ML-FKL
Replacement function key label insert for C-more Micro-Graphic panels
(pk of 5; 3 blank, 1 F1-F5 for landscape, 1 F1-F5 for portrait)
Replacement mounting clip for C-more Micro-Graphic panel and keypad bezels (pk of 8)
Replacement DC power connector (pk of 5)
Replacement mounting gasket for C-more 6” Micro-Graphic panels
Panel Mounting Clips
Part No. EA-MG-BZ2-BRK
Clear Screen Overlay
0.484
[12.3]
0.886
[22.5]
PWR
0.197
[5.0]
0.157
[4.0]
3.795
[96.4]
DC Power Connector
Part No. EA-MG-DC-CON
(pk of 8)
Step 1
(pk of 5)
Remove the overlay from the package
Panel Gasket
Part No. EA-MG6-S6ML-GSK
Keypad Bezel Gasket
Part No. EA-MG6-BZ2-GSK
(pk of 5; 3 blank, 1 F1-F5 for
landscape, 1 F1-F5 for portrait)
Step 3
Align the overlay with the screen and
press the adhesive firmly into place
2.598
[66.0]
2.539
[64.5]
Step 2
Remove the paper backing from the overlay
0.923
[23.4]
4.803
[122.0]
RxD
4.913
[124.8]
EA-6-COV2
1.417
[36.0]
TOP VIEW
TxD
Dimensions
EA-6-COV2
LED Status Indicators
Units: inches [mm]
6.394” (W) x 10.000” (H) x 2.488” (D)
[162.4 mm x 254.0 mm x 63.2 mm]
26.1 oz. [740 g]
Function Keys Label Inserts
Part No. EA-MG6-S6ML-FKL
* Note: Maximum cable length for either the USB or serial cable should not exceed 2.0 m [6.56 feet] in length.
Converter Status Indicators
Connects with expansion connector on the rear of the C-more 6” Micro-Graphic panel.
Description
EA-MG-BZ2-BRK
EA-MG-DC-CON
EA-MG6-S6ML-GSK
EA-MG6-BZ2-GSK
• Weight
Environmental: Same as C-more Micro-Graphic panel specifications.
Converter
Dimensions
EA-S6ML, EA-S6MLW
• Weight
Replacement Parts
2.559” (W) x 1.417” (H) x 0.886” (D)
[65.0 mm x 36.0 mm x 22.5 mm]
1.06 oz. [30 g]
• Dimensions
EA-MG6-BZ2P
• Dimensions
EA-MG-PGM-CBL
6-ft. cable assembly to connect personal computer to any C-more Micro-Graphic panel for setup and
programming. (Note: This cable assembly uses the PC's USB port and converts the signals to serial
transmissions. The USB port supplies 5 VDC to the Micro-Graphic panel for configuration operations.) Assembly
includes standard USB A-type connector to B-type connector cable, custom converter, and an RS232C cable
(DV-1000CBL) with RJ12 modular connector on each end.
Description:
ENCLOSURE MOUNTING
THICKNESS RANGE
0.04” - 0.2” [1 - 5mm]
21-Button Keypad Bezel Specifications
Part Number:
General:
• Micro-Graphic
Panels Supported
• Connection
• Power Consumption
• Keypad Button Life
• Noise Immunity
• Weight
Hardware:
Step 3 - If desired, print and
apply self adhesive labels to
the blank insert.
Minimum of 500,000 cycles
NEMA ICS3-304
RFI, (145 MHz, 440 Mhz 10 W @ 10 cm)
Impulse 1000 V @ 1 µs pulse
• Noise Immunity
1.894” [47.1 mm]
30.69 oz. (870 g)
None
IEC60068-2-27 (Test Ea), 15 G peak, 11 ms duration, three shocks in each direction
per axis, on 3 mutually perpendicular axes (total of 18 shocks)
• Shock
NOTE: Mounting clips for the
panel or keypad bezel are
included with each product
Connects with expansion connector on the rear of the C-more 6” Micro-Graphic panel.
IEC60068-2-6 (Test Fc), 5-9 Hz: 3.5 mm amplitude, 9-150 Hz: 1.0G, sweeping, at a rate of
1 octave/min. (±10%), 10 sweep cycles per axis on each of 3 mutually perpendicular axes
• Vibration
Terminals
1.126
[28.6]
EA-S6ML, EA-S6MLW
(8) mounting clips, EA-MG-BZ2-BRK, included.
• Enclosure Mounting
• Operating Temperature
Country of Origin
1.873
[47.6]
EA-MG6-BZ2
Environmental:
Dimensions
EA-COMCON-3
Four directional cursor buttons, numeric
buttons, and ESC,
MENU, CLEAR and
two ENTER buttons.
GASKET
NOTE: Mounting clips for the
panel or keypad bezel are
included with each product
R
D-SUB 15-pin to Terminal Block Adapter (EA-COMCON-3)
Enter
Enter
Panel Thickness
Dimensions
Units: inches [mm]
0.382
[9.7]
+1
143.0 –0
Units: Inches [mm]
Enter
6.394
[162.4]
5.588
[141.9]
+0.04
5.630 –0.00
0.382
[9.7]
EA-MG6-BZ2 Keypad
Bezel Dimensions
6.394
[162.4]
5.588
[141.9]
MOUNTING CLIP (Qty: 8)
SCREW TORQUE RANGE
21 - 28 oz-in [0.15 - 0.2 Nm]
21 – 28 oz-in [0.15 – 0.2 Nm]
0.709
[18.0]
Typical
5
EA1-S6MLW?{0752015001
6.5 W @ 10.2 VDC (630 mA)
Type AGC fast acting glass fuse,
750 mA, 250 VAC, ADC p/n AGC-75
10 A for 500 µs
*NOTE: When the 6” panel is powered through Port1 from a connected PLC or PC, the screen brightness is diminished because the panel is running in Low-Power Mode. For full brightness, connect
an external 12-24 VDC power source to the 6” panel’s power connection. Low-Power Mode should
be used during initial programming only. Connect an external 12-24 VDC power source when the
panel is installed in its application.
0.282
[7.15]
9
4
CLR
R
0.04” – 0.2” [1 – 5 mm]
0.563
[14.3]
8
LISTED
7M17
IND.CONT.EQ.
R
Step 4 - Install the new insert
into the slot in the side of the
panel and lock tab into place.
Menu
7
20-Button Keypad Bezel Specifications
0 to 50 °C (32 to 122 °F)
Maximum surrounding air temperature rating 50 °C
–20 to +60 °C (–4 to +140 °F)
5–95% RH (non-condensing)
For use in Pollution Degree 2 environment
IEC60068-2-6 (Test Fc), 5-9 Hz: 3.5 mm amplitude, 9-150 Hz: 1.0G, sweeping, at a rate of
1 octave/min. (±10%), 10 sweep cycles per axis on each of 3 mutually perpendicular axes
IEC60068-2-27 (Test Ea), 15 G peak, 11 ms duration, three shocks in each direction per axis,
on 3 mutually perpendicular axes (total of 18 shocks)
NEMA ICS3-304
RFI, (145 MHz, 440 Mhz 10 W @ 10 cm)
Impulse 1000 V @ 1 µs pulse
For use on a flat surface of Type 1, 4X enclosure (for indoor use only)
CE (EN61131-2), UL508, CUL Canadian C22.2 No. 142-M95, UL File E157382, CSA File 234884
Step 2 - Remove the
protective film from the
blank key label insert.
Esc
R01.1 2 3 4 5
MODEL:EA1-S6MLW
INPUT:12-24V 6.5W
Date code:****
MADE IN CHINA
Supplied from an external class 2, 12-24 VDC
power source
Maximum 1 ms
• Enclosure Mounting
Thickness Range
• Mounting Clip Screw
Torque Range
• Depth from bezel rear
with options Module
• Weight
MOUNTING CLIP (Qty:8)
SCREW TORQUE RANGE
21 - 28 oz-in [0.15 - 0.2 Nm]
0.394
[10.0]
R0.59 [R1.5]
0.382
[9.7]
Units: Inches [mm]
Enclosure Mounting Thickness
6.850” (W) x 5.331” (H) x 2.130” (D) [174.0 mm x 135.4 mm x 54.1 mm] (Landscape Mode)
5.331” (W) x 6.850” (H) x 2.130” (D) [135.4 mm x 174.0 mm x 54.1 mm] (Portrait Mode)
• Dimensions
Units: Inches [mm]
2.094 1.882
[53.2] [47.8]
0.751
[19.1]
• Recommended Fuse
High Power Mode
MOUNTING CLIP
SCREW TORQUE RANGE
21 - 28 oz-in [0.15-0.2 Nm]
0.903
[22.9]
• Power Consumption
Low Power Mode*
Mounting Clip Screw Torque
ENCLOSURE MOUNTING
THICKNESS RANGE
0.04” - 0.2” [1 - 5mm]
TERM
• Input Power
Lines, Rectangles, Circles and Frames
Fixed fonts: 6x6, 6x8, 8x16, 16x16, 32x16, 32x32, and Windows fonts
0.382
[9.7]
10.000
[254.0]
9.195
[233.5]
0.412
[10.5]
• Static Shapes
• Displayable Fonts
Electrical:
• Input Voltage Range
EA-MG6-BZ2 Keypad
Bezel Dimensions
RD+
• Functional Devices
+0.04
+1
234.6 –0
0.564
[14.3]
• Expansion Connection
Screen Objects:
1792 kBytes
Up to 999 – limited by project memory usage
Yes
Five user defined function key buttons with the ability to custom label with an overlay.
Minimum of 500,000 cycles
Each function key button includes a red LED that can be user programmed.
Built-in RJ12 serial communications port (RS-232)
and 15-pin D-sub serial communications port (RS-232, RS-485 / 422).
Yes – used with optional Keypad Bezels, EA-MG6-BZ2 & EA-MG6-BZ2P
CUTOUT
9.236 –0.00
SD+
• Serial Communications
Analog touch panel
82 gram force [0.8 N] maximum
Minimum of 1,000,000 cycles
CUTOUT
OUTLINE
+1
–0
5.331
[135.4]
4.770
[121.3]
GND
• Keypad Function Button LEDs
143.0
1.605
[40.8]
• Keypad Function Buttons
CUTOUT
CUTOUT
OUTLINE
0.382
[9.7]
BEZEL
OUTLINE
+0.04
LED
Model EA1-S6ML : 5 user defined colors:
Red, Green, Amber, Lime, and Yellow
Model EA1-S6MLW : 5 user defined colors:
White, Pink1, Pink2, Pink3, and Red
No
• Color
BEZEL
OUTLINE
0.382
[9.7]
5.630 –0.00
RD–
Backlight:
• Type
+1
234.6 –0
R0.59 [R1.5]
TERM
• Viewing Angle
EA-MG6-BZ2P
Cutout Dimensions
+0.04
Units: Inches [mm]
NOTE: Panel shown in
Landscape (Horizontal)
orientation
RD+
• Viewing Area Size
• Active Area Size
• Contrast
• User Replaceable
Touch Screen:
•Type
• Operation
• Life
Features:
• User Memory
• Number of Screens
• Beep (Internal)
High Power Mode
1.756
[44.6]
• Display Brightness
(Reference)
SD–
• Color
EA-MG6-BZ2P
Keypad Bezel
9.236 –0.00
0.382
[9.7]
0.382
[9.7]
6.850
[174.0]
.236
[6.0]
21 Button Landscape (Horizontal) Keypad Bezel
EA-MG6-BZ2
Cutout Dimensions
GASKET
SD–
• Resolution
EA-MG6-BZ2
Keypad Bezel
MOUNTING CLIP
(4) places
2.13
1.453
[54.1] 1.689 [36.9]
[42.9]
5.7" STN monochrome LCD, graphical characters
320 (W) x 240 (H) dots (Landscape Mode)
240 (W) x 320 (H) dots (Portrait Mode)
2 colors (normal / inverse)
SD+
Display:
• Type
EA1-S6ML & EA1-S6MLW
Panel Dimensions
RD–
Description:
20 Button Landscape (Horizontal) Keypad Bezel
C-more Micro-Graphic Panel Dimensions
*NOTE: The protective
cover ships with a thin
protective sheet on the
face of the cover that
needs to be carefully
removed. If your panel
Step 4
is not clear, the protective sheet may not have Remove the protective film*
been removed.
Units: inches [mm]
LEFT VIEW
FRONT VIEW
Data Sheet: EA1-MG6-QSG, Rev. L
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement