Siemens SpeedStream 4200 modem Quick-Start Guide
Below you will find brief information for modem SpeedStream 4200. The SpeedStream 4200 is a DSL modem that connects your computer to the Internet. It includes the following features: a DSL modem, a PPPoE modem, and a router. You can use the SpeedStream 4200 to connect to the Internet, share files with other computers on your network, and access the Internet from multiple devices.
Advertisement
Advertisement
Part # 007-4023-001
Quick-Start Guide
SpeedStream ®
4200 Modem
PPPoE Modem
Router
2
Before you begin,
Verify that the following items came with your DSL kit:
1
3 4
2
• •
Step 1
>
Install Line Filters
Stand-alone Line Filter
1 SpeedStream® Device
2 Documentation
3 Software Manual CD-ROM
+ USB drivers
4 Power supply
5 USB cable
6 RJ-45 Straight-through
Ethernet cable
7 RJ-11 DSL cable
2
1
Wall-mount Filter
3
5 6 7
Your service provider may include an Ethernet adapter, a line filter, and a wall-mount filter in your DSL kit. If you received any of these items, follow the instructions provided in this guide for basic installation. If you need further assistance installing these items, please contact your service provider.
1 2 3
Devices such as fax machines, caller
ID boxes, or phones that share the same phone line as your DSL account require a line filter, which prevents noise from disrupting the
DSL signal on the phone line. Filters can be in the form of a stand-alone line filter or a wall-mount filter.
Stand-alone Line Filter
For each device that shares the
DSL phone line:
1. Unplug the device’s cord from
the phone jack.
2. Plug the filter into the
phone jack.
3. Plug the phone cord (or other
device cord) into the filter.
Wall-mount Filter
For a wall-mount phone, install a wall-mount filter.
1. Remove the phone.
2. Connect the wall-mount filter
to the wall plate.
3. Reconnect the phone.
A PCI Ethernet adapter
B Line filter(s)
C Wall-mount filter
A B C
3
Step 2
>
Choose an Installation Method
4
The SpeedStream ® device may be connected to either an existing USB port or an Ethernet port. If you choose to attach the SpeedStream ® device via the Ethernet interface, it is only necessary to complete the steps in Option A. Otherwise, proceed directly to Option B for
USB installation.
Option A >
Ethernet Installation Method
Install Ethernet Adapter
You will need to install an Ethernet adapter if your computer does not already have one installed. Refer to your Ethernet adapter manufacturer’s documentation for complete installation instructions.
Connect the SpeedStream
®
Device
1. Connect the straight- through Ethernet cable
(RJ-45) to the Ethernet port on the SpeedStream ® device (yellow port).
2. Connect the other end of the straight-through
Ethernet cable (RJ-45) to the Ethernet port on your computer.
3. Plug the DSL cable (RJ-11) into the DSL port on the
SpeedStream ® device
(gray port).
4. Plug the other end of the DSL cable (RJ-11) into the phone jack.
5. Plug the power adapter into the power outlet and SpeedStream ® device
(black port).
6. Ensure the SpeedStream ® device is powered on (power switch located on right side of back panel).
4
Internet connection
RJ-11 DSL cable
Ethernet connection to computer RJ-45
Straight-through
Ethernet cable
2
3
1
6
Power supply
Hub
Optional: use crossover
(Xover) cable when connecting to a hub or switch without an
“uplink” port
5
You have completed the installation of your SpeedStream ® hardware. There is no software installation required when using the Ethernet connection method. If you have the router model, proceed to Step 3 to configure your router and connect to the Internet.
Option B >
USB Installation Method
Connect the SpeedStream
®
Device
1. Connect the USB cable to the
USB port at the rear of the
SpeedStream® device (blue port).
2. Connect the other end to the USB port on your computer.
3. Plug the DSL cable (RJ-11) into the
DSL port on the SpeedStream ® device.
4. Plug the other end of the cable
(RJ-11) into the phone jack.
5. Plug the power adapter into the power outlet and SpeedStream ® device.
6. Ensure the SpeedStream ® device is powered on (power switch located on right side of back panel).
4
Internet connection
RJ-11 DSL cable
2
USB connection to computer
3
1
6
Power supply
5
You have completed the installation of your SpeedStream ® DSL hardware.
Install the USB driver software on your PC using one of the procedures below.
Windows USB Driver Installation
Software Installation
You will need to install USB drivers, if you are connecting the SpeedStream® device to your computer via the USB port. Before installing the software, make sure your PC is equipped with the following:
Windows ® 98, Windows ® 98 Second Edition (SE), Windows ® 2000 Professional, Windows ® Millennium Edition
(Me), or Windows ® XP; 32 MB RAM; Pentium-compatible 166 MHz or faster processor; 12 MB available hard disk space.
1. Insert the SpeedStream ® Installation CD into your CD-ROM drive. This will automatically start the software installation program. Follow the on-screen directions to complete the software installation.
2. After the USB driver is installed, continue with PC Configuration Procedures described on the next page.
If the software installation program does not automatically start, you can manually start it using the following procedure.
1. Click Start > Run.
2. Browse to setup.exe on the CD and double-click it. This will start the software installation program.
3. Follow the on-screen directions to complete the software installation.
Macintosh USB Driver Installation
Software Installation
Before installing the software, make sure your Mac is running OS 8.6 or above. This procedure will restart your computer to complete the installation.
1. Insert the SpeedStream ® Installation CD into your CD-ROM drive.
2. Open the SpeedStream ® Icon from the desktop.
3. Click Readme.txt.
4. Follow the directions in the Readme.txt to complete the software installation.
5. After the USB driver is installed, continue with PC Configuration Procedures described on the next page.
5
6
Step 3
>
PC Configuration Procedures
Windows Configuration
In order to setup the SpeedStream ® device, your PC must first be configured to obtain an
IP address from a DHCP server. Follow the procedure below:
Note: The following procedures cover configuration of a PC running Windows XP. Please refer to the User Guide on the
CD-ROM for help configuring other operating systems.
1. Click Start > Control Panel.
2. Double-click the Network
Connections icon.
3. Double-click your Network Card.
4. Click Properties.
5. Select Internet Protocol (TCP/IP).
6. Click Properties.
7. Select Obtain an IP address
automatically.
8. Select Obtain DNS server address
automatically.
9. Click OK and exit out of the Control Panel.
10. Configure Internet Access using the procedure that follows.
Internet Access
Next, make sure your PC will use the
SpeedStream ® device (and not Dial-Up
Networking) when connecting to the
Internet. Follow the procedure below:
1. Click Start > Control Panel.
2. Double-click the Internet Options icon.
3. Click the Connections tab.
5. Click Next.
6. Select Connect to the Internet.
7. Click Next.
8. Select Setup my connection manually.
9. Click Next.
10. Select Connect using a broadband
connection that is always on.
11. Click Next.
12. Click Finish.
13. If you have a router, configure the router using the Router Configuration procedure that follows.
Router Configuration
Windows Me and XP users: If you have Universal
Plug and Play (UPnP) enabled, Windows may detect the SpeedStream ® device upon startup and provide a shortcut to the device on the desktop or system task tray. The icon will be labeled as “Residential Gateway.” Double-click the icon and skip to step 3.
1. Start your Web browser.
2. In the Address box, enter the following: http://speedstream
3. When prompted for a username and password, type admin for the password only (username is not required).
4. Click Login and enter the username and password provided by your service provider.
5. Click Save.
6. If additional configuration is desired, select Setup to configure DHCP, firewall settings, security options, and also to view status and statistical information.
Note: If your Service Provider requires you to use separate
PPPoE client software, discontinue use of this software.
The SpeedStream
®
device will negotiate the PPPoE logon to your service provider’s network.
4. Click Setup.
Congratulations! You have completed the installation of your SpeedStream
®
device.
Macintosh Configuration Procedures
Macintosh Configuration
In order to setup the SpeedStream ® device, your computer must first be configured to obtain an IP address from a DHCP server.
Follow the procedure below for OSX:
1. Click Apple -> System Preferences.
Follow the procedure below for OS9:
1. Click Apple -> Control Panels -> TCP/IP.
2. Select the Network icon under the
Internet & Network section.
3. Select one of the following from the
Show drop-down menu:
• Built–in Ethernet if connecting
via Ethernet.
• Ethernet Adaptor [en0, en1,...]
if connecting via USB.
4. Select Using DHCP Server from the
Configure IPv4 drop-down menu.
5. Click Apply Now and exit out of
System Preferences window.
6. If you have a router, configure the router using the Router Configuration procedure that follows.
2. Select one of the following from the
Connect via drop-down menu:
• Ethernet or Ethernet built–in if
connecting via Ethernet.
• SpeedStream 5x Series if connecting
via USB.
3. Select Using DHCP Server from the
Configure drop-down menu.
4. Close window and save changes.
5. If you have a router, configure the router using the Router Configuration procedure that follows.
Router Configuration
1. Start your Web browser.
2. In the Address box, enter the following: http://speedstream
3. When prompted for a username and password, type admin for the password only (username is not required).
4. Click Login and enter the username and password provided by your service provider.
5. Click Save.
6. If additional configuration is desired, select Setup to configure DHCP, firewall settings, security options, and also to view status and statistical information.
Congratulations! You have completed the installation of your SpeedStream
®
device.
7
Troubleshooting
LED
Power
Off
- Power not
applied
Green
Normal system operation
Blinking
Green
N/A
Ethernet traffic flowing in either direction
Red
Self-test failure if red for more than
30 seconds
N/A N/A
Blinking
Red/Green
Flash write in progress
Ethernet - Power not
applied
- Ethernet link
not connected
DSL - Power not
applied
- DSL signal
not detected
USB
Activity
- Power not
applied
- No USB
connection
- Power not
applied
- No LAN
data activity
Ethernet link connected
DSL line is trained and ready for traffic
USB
Connected
N/A
DSL is training N/A
USB user traffic flowing in either direction
N/A
LAN user traffic flowing in either direction
N/A
N/A
N/A
N/A
8
Siemens Subscriber Networks, Inc.
4849 Alpha Road
Dallas, TX 75244
(972) 852-1000
Fax (972) 852-1001 [email protected]
http://www.icn.siemens.com/subscriber
Copyright© 2004 SIEMENS SUBSCRIBER NETWORKS, INC. All rights reserved. Siemens and the Siemens logo are trademarks of Siemens AG, Germany. All other trademarks are held by their respective companies. Siemens reserves the right to make changes to product specifications at any time without notice.
Download
Advertisement
Key features
DSL Modem
PPPoE modem
Router
USB connection
Ethernet connection
Wall-mount Filter
Frequently asked questions
The SpeedStream 4200 is a DSL modem and router that allows you to connect to the internet using a DSL line.
You can connect to the internet using the SpeedStream 4200 by connecting it to your computer via an Ethernet cable or a USB cable.
A DSL line is a high-speed internet connection that uses your existing phone line to deliver internet access.
PPPoE is a common internet connection protocol that is used by many DSL internet service providers.