Converters.TV | 535 | Instruction manual | Converters.TV 535 Instruction manual

Converters.TV 535 Instruction manual
TX-NR535
AV RECEIVER
Basic Manual
Advanced Manual found here
http://www.onkyo.com/manual/txnr535/adv/en.html
En
Before Start
Advanced Manual
Advanced Manual is always updated with the latest
information and its user friendly interface, which does not
matter whether you access from PC or Smartphone, helps
you to understand more deeply about the AV Receiver.
Advanced Manual is consisted of the following chapters.
r Details on AM/FM playback
r Playing Music Files on a USB Storage Device
r Listening to Internet Radio
r Playing Music with DLNA
r Playing Music Files in a Shared Folder
r Operating Music Files with the Remote Controller
r Using the Listening Modes
r Advanced Settings
r Operating Other Components with the Remote Controller
r Connecting/Operating Onkyo product with RI jack.
r Updating the Firmware
r Details on Troubleshooting
r Reference Information
Advanced Manual found here
http://www.onkyo.com/manual/txnr535/adv/en.html
2
Supplied Accessories
Indoor FM antenna --- (1)
AM loop antenna --- (1)
Color labels for speaker cable --- (1)
Speaker Cable
1
The unit is designed to be connected in between the TV
and the playback devices such as Blu-ray disc player.
Video signal from the playback devices will be sent through
the unit to the TV and audio will be reproduced with the
speakers creating Dolby Digital or other kind of surround
sound field. The unit has many in/out jacks on its rear
panel which allows you to connect a lot of playback devices
simultaneously. Playback can be switched by selecting
the input selector buttons. For playback of CEC compliant
devices, input will be switched automatically.
r Equipped with 5 channel amplifier
r Equipped with 4K 60 Hz Passthrough-compatible HDMI
IN/OUT jacks
r Supports the HDMI Through function which allows
transmission from playback devices to the TV in standby
state
r Supports ARC (Audio Return Channel)
r Supports USB storage playback
r Supports variety of network functions such as Internet
Radio, DLNA, etc.
r Supports Wi-Fi and Bluetooth
r A/V Sync Control Function to correct deviation of audio
and video
r Zone2 function which allows you to play a different
source in another room from the main room
r T-D (Theater-Dimensional) listening mode which allows
you to enjoy the virtual surround sound field
r 192 kHz/24 bit D/A converter
r Automatic speaker setup available using supplied
calibrated microphone (AccuEQ Room Calibration)
r 32 bit DSP (Digital Signal Processor) with excellent
calculation performance
r Supports playback of MP3, WMA, WMA Lossless, FLAC,
WAV, Ogg Vorbis, Apple Lossless, DSD, Dolby TrueHD
via network and USB storage device
2
Features
The Basic Manual leads you through the fundamental steps
to enjoy the AV Receiver from connections to TV, speaker
system and playback devices, to necessary functions for
playback. As well as that, Basic Manual informs you with
the instructions on frequently used functions. Besides, there
is another part of the manual called Advanced Manual to
inform you with more detailed information, which we have
decided to publish on the web from the ecological point of
view.
3
About the Basic Manual
Remote controller (RC-879M) --- (1)
Batteries (AA/R6) --- (2)
Power cord (Taiwanese model) --- (1)
Speaker setup microphone --- (1)
The number in parenthesis indicates the quantity. On packaging,
the letter at the end of the product name indicates the color.
Step 1: Connections
Personal computer
TV
HDMI
OUT
HDMI
IN
HDMI cable
¼
To use the ARC function, connect to the
ARC compatible HDMI jack of the TV.
HDMI
OUT
HDMI
OUT
HDMI
OUT
Blu-ray Disc/
DVD player
HDMI
OUT
Game console
Set-top box/Digital
video recorder, etc.
1
Satellite/Cable
set-top box, etc.
¼
Select an appropriate
connection for your TV.
www.onkyo.com/manual/txnr535/adv/en.html).
Connecting the TV and players
Important: The power cord must be connected only after all
other connections are completed.
HDMI cable connection
The unit has many HDMI jacks on its rear panel and each
of them corresponds to an input selector button of the same
name on the front panel. For example, a Blu-ray Disc player
will be connected to the IN 1 jack and the BD/DVD button
on the front panel will be used to listen to the playback
sound (if the player is CEC compliant, input will be switched
automatically). If you add another Blu-ray Disc player, you
can use any other jack than IN 1. It is possible to change
assignment of the input jacks and input selector buttons.
For how to make settings, see the Advanced Manual (http://
To connect the TV and the unit, connect the HDMI OUT
jack of the unit and the HDMI input jack of the TV with an
HDMI cable. With this connection, it becomes possible to
display the setting screen of the unit on the TV or transmit
video/audio signals from the player to the TV. If your TV
supports ARC (Audio Return Channel), it is possible to
play the TV sound with the AV receiver's speakers with this
connection only.
If your TV does not support ARC, you need, in addition
to the HDMI OUT jack connection, a digital optical cable
connection between the digital audio out optical jack of
the TV and the DIGITAL IN OPTICAL jack of the unit or an
analog audio cable connection between the audio output
jack of the TV and the TV/CD analog audio input jack of the
unit.
TV
DIGITAL
OPTICAL
OUT
AUDIO
OUT
Connection with a TV not supporting ARC
The unit supports the HDMI Through function that allows
transmission from players to the TV even if the unit is in standby.
r It is necessary to make appropriate settings to enable
the HDMI linked system function, ARC function and
HDMI Through function. See the section 4 of "Step 2:
Setting Up".
3
Step 1: Connections
Connecting Components without HDMI
The video/audio jacks other than HDMI jacks also have a
preassigned input selector button on the front panel. See the
name of the input selector button shown with the jack when
connecting the device. It is possible to change the assignment
if necessary. For more information, see the Advanced Manual
(http://www.onkyo.com/manual/txnr535/adv/en.html). Note that
when connecting the player to the 2 COMPONENT VIDEO
IN jacks, you need to connect the TV to the 2 COMPONENT
VIDEO OUTPUT jacks. Also note that when connecting the
player to the 3 composite video input jack, you need to
connect the TV to the 4 MONITOR OUT jack.
1 DIGITAL IN jacks: A player with a digital audio out optical
jack or digital coaxial audio out jack can be connected. To
enjoy digital surround sound including Dolby Digital and DTS,
use one of these connections or the HDMI cable connection.
2 COMPONENT VIDEO jacks: A TV with component
video input jacks or a player with component video
output jacks can be connected.
3 VIDEO/AUDIO IN jacks: A player with a composite video
output jack or RCA audio output jacks can be connected.
4 MONITOR OUT V jack: A TV with a composite video
input jack can be connected.
1
2
3
4
If the connected turntable does not have built-in
audio equalizer, you need to install an external audio
equalizer between the unit and the turntable. Contact the
manufacturer for more information.
Type of cables
„ Video/audio transmission
HDMI cable: Enables digital
transmission of video/audio signals
and control signals between devices
via single cable connection.
¼Use high speed HDMI cable when playing
back 4K 1080p high definition video.
„ Audio transmission
Digital optical cable: Transmits digital
audio. The audio quality is the same as
that of the digital coaxial cable.
¼As the digital in optical jack of the unit
has a cover, push in the cable against the
cover as it is turned inside.
Digital coaxial cable: Transmits digital
audio. The audio quality is the same as
that of the digital optical cable.
Analog audio (RCA) cable: Transmits
analog audio signals.
„ Video transmission
Component video cable: Transmits
higher quality video signals than those
of the composite video cable.
Composite video cable: Transmits
analog video signals.
4
Step 1: Connections
2
Front R
Front L
Connecting speakers
Important: The power cord must be connected only after all
other connections are completed.
12
3
Center
Connection of each
speaker: Correctly
connect + and -. Using
the colored labels for
speaker cables will help
correct connection.
6
45
12
3
45
6
Front speakers
Center speaker
Surround speakers
Subwoofer
¼
Up to two subwoofers can be connected.
It is ideal to install the front speakers and center speaker
at the height not too far from that of the screen. As for the
surround speakers, it is recommended to install at the
position slightly backward of the listening position and
higher than the listener's ears, since it is preferable to
obtain a diffused sound rather than a direct sound. As a
bass sound reproduced by subwoofer is less directional,
it is possible to place it at any position. Consider the best
installation position where a bass sound can be clearly
heard by listening to actual playback.
%QPPGEVURGCMGTUYKVJŝVQŝKORGFCPEG7UKPI
a speaker with less impedance than the supported
value may result in failure.
Surround R
Surround L
Subwoofer with built-in
power amplifier
1/2"-5/8"(12-15 mm)
Cut and remove the plastic coating from the end of the
speaker cable, twist the core and connect it to the terminal.
Make correct connection between the unit's jacks and
speaker's jacks (+ to + and - to -) for each channel. If
connection is wrong, a bass sound may become poor due to
reverse phase. Attaching the supplied colored speaker cable
5
Step 1: Connections
labels to the + side on the both ends of each channel's cable
will help correct connection. The subwoofer jack supports
connection of a subwoofer with built-in power amplifier. Set
the cut-off filter selection switch of the subwoofer to DIRECT.
If the subwoofer does not have a cut-off filter selection
switch but has a cut-off frequency adjusting dial, turn it to the
maximum frequency. If your subwoofer does not have built-in
power amplifier, you can connect a power amplifier between
the unit and the subwoofer.
r The speaker setting is 5.1 ch at the time of purchase. You
can change it manually or by using automatic speaker
setting.
r Short-circuiting the + cable and - cable or contacting the
cable core to the rear panel of the unit may cause failure.
Also do not connect two or more cables to one speaker
jack or one speaker to several jacks.
3
Network connection
Other connections
AM/FM antenna connections
Connect the antennas to listen to AM/FM broadcast. When
listening to the broadcast for the first time, adjust the
antenna position and orientation to get the best reception.
You can enjoy Internet radio and DLNA by connecting the
unit to LAN. The unit can be connected to the router with
an Ethernet cable or to the wireless LAN router with WiFi connection. In case of wired connection, connect the
Ethernet cable to the Ethernet port. For Wi-Fi setup, see
the section 3 of "Step 2: Setting Up".
Internet radio
AM loop antenna (supplied)
Router
Indoor FM antenna
(supplied)
NAS
Fix with a tack on
the wall.
(North American and
Taiwanese models)
(European, Australian
and Asian models)
Assemble the AM loop antenna (supplied).
When using commercially available banana plugs:
tighten the speaker terminals to the end and then insert
the banana plugs. Do not insert the cable core directly into
the center hole of the speaker terminal. (North American
model)
6
PC
Headphones connection
Connect stereo headphones with a standard plug (1/4
inch or ø 6.3 mm) to the PHONES jack. Sound from the
speakers will be off while you are using the headphones.
r If you selected any other listening mode than Pure
Audio (European, Australian and Asian models), Stereo,
Mono and Direct, connecting headphones will switch the
listening mode to Stereo.
Step 2: Setting Up
1
Turning the power on
Connect the power cord to the outlet (¼). Press zON/
STANDBY on the main unit or zRECEIVER on the remote
controller to turn the unit on or to standby mode.
r When the unit is turned on, a large instantaneous current
may flow affecting functionality of the computer and other
devices. It is recommended to use a separate outlet from
that for the computer or such other sensitive devices.
¼Taiwanese model includes a removable power cord. Connect the power
cord to AC INLET of the unit and then connect to the outlet. Always
disconnect the outlet side first when disconnecting the power cord.
Firmware update notification: If the unit is connected via
LAN and there is firmware update available, the "Update
New F/W" message will appear. Press the S/T buttons on
the remote controller to select whether to update or not
and press ENTER to confirm your selection. For details on
firmware update, see the Advanced Manual (http://www.
onkyo.com/manual/txnr535/adv/en.html).
2
2. Connect the speaker setup microphone to the
Making automatic speaker setting
SETUP MIC jack on the unit.
SETUP MIC jack
The AccuEQ Room Calibration function, our proprietary
technology, collects the test tones coming from each
speaker with the supplied speaker setup microphone and
performs automatic setting of the number of speakers,
volume level, each speaker's optimum crossover
frequencies, and distance from the primary listening
position. Distortion caused by difference of room acoustic
environment will also be corrected to produce clear, wellbalanced sound.
1. Place the speaker setup microphone at the
measurement position .
r Correct measurement will not be possible if the
microphone is held by hand. It is desirable that the
microphone be placed on a stand at the height
of listener's ears. Measurement is not possible if
headphones are being used.
Speaker setup
microphone
3. Follow the guidance displayed on the TV screen.
You can set up by viewing the guidance displayed on the
TV screen. To display the guidance, you need to make
HDMI connection between the unit and TV. Select the
item with the cursor buttons of the remote controller and
press ENTER to confirm your selection.
AccuEQ Room Calibration
TV
Subwoofer
<
Yes
>
[ENTER] : Next
: Listening area
: Measurement position
with microphone
4. The test tones sound from the connected speaker
and automatic speaker setting starts.
The microphone measures the test tones. Measurement
will be made twice for each speaker. It takes several
minutes to be completed.
r Each speaker generates test tones at high volume
level during measurement. Keep the room as quite
as possible during measurement. Measurement
may be interrupted if there is ambient noise or radio
frequency interference. Close the window and turn off
the home appliance and fluorescent light.
r To cancel measurement on the way, disconnect the
microphone plug.
7
Step 2: Setting Up
5. When the measurement is completed, the
measurement result is displayed.
3
3. Select and set the authentication method.
Making Wi-Fi setting
Wi-Fi Setup
AccuEQ Room Calibration
<-Review Speaker Configuration->
Subwoofer
Front
Center
Surround
Crossover
:
:
:
:
:
Yes
Small
Small
Small
150 Hz
Save
Cancel
Press d/c on the remote controller to check the settings.
Pressing ENTER when "Save" is selected will save the
settings.
r The subwoofer sound may not be detected since
it is extremely low frequencies. If "No" is shown for
"Subwoofer" in the measurement result screen,
raise the subwoofer volume to around the half of
its maximum volume and make its frequency to the
maximum level.
6. On the screen showing "AccuEQ" is "On", press
ENTER.
The settings will be applied to all the inputs.
7. When "Please unplug setup microphone." is
displayed, disconnect the microphone.
r If you change the speaker positions, the room furniture
layout or the number of speakers, perform automatic
speaker setting again.
r If there is an error message, follow the on-screen
instruction to remove the error cause.
Items to be checked before starting the procedure
Wi-Fi connection requires an access point such as
wireless LAN router (¼). Write down the SSID and
password (key) of the access point if they are shown
in the label of the main body. If the access point has
an automatic setting button (may be called differently
according to the manufacturer), you can set up
without inputting the password. For how to use the
automatic setting button of the access point, refer to
its instruction manual.
¼
The unit supports Wi-Fi connection with 2.4 GHz
access point.
z Operation: You can set up by viewing the guidance
displayed on the TV screen. To display the guidance, you
need to make HDMI connection between the unit and
TV. Select the item with the cursor buttons of the remote
controller and press ENTER to confirm your selection. To
return to the previous screen, press RETURN.
1. Start "Wi-Fi Setup".
1 Press RCV on the remote controller and then press
HOME.
2 Select "Setup" with the cursor buttons and press
ENTER.
3 Select "12. Network Setup" with the cursor buttons and
press ENTER.
r "12. Network Setup" becomes selectable after the
network starts up even if it cannot be selected first. It
may take about a minute to start up.
4 Select "Wi-Fi" with the cursor buttons and select "On" to
display "Wi-Fi Setup".
5 Select "Start" in "Wi-Fi Setup" with the cursor buttons
and press ENTER.
2. Select the SSID of the access point to be connected
with the cursor buttons and press ENTER.
When the SSID of the access point appears on the TV
screen, select the desired access point.
r If you changed the initial setting of the access point to
skip password entry, step 4 starts automatically.
r If you changed the initial setting of the access point
to hide the SSID, see "When the access point is not
displayed".
8
Please select the authentic
method.
Enter Password
Push Button
PIN code
When the screen above is displayed, select and set one of
the three authentication methods: "Enter Password", "Push
Button" and "PIN code". See below for details of and how to
set each method.
„ Enter Password: Enter the password of the access point
to establish connection.
1 Select "Enter Password" with the cursor buttons and
press ENTER.
2 Enter the password (¼) on the keyboard screen, select
"OK" with the cursor buttons and press ENTER.
r In some case, the key board screen is displayed
automatically instead of authentication screen
depending on access point device.
¼
To switch uppercase/lowercase, select "Shift" and press ENTER.
Select "Left" or "Right" and press ENTER to move the cursor to
the selected direction. Select "BS" and press ENTER to delete
the character at the left of the cursor position. To select whether to
mask the password with "*" or display it in plain text, press D on the
remote control. Press + 10 on the remote controller to enable the
"Shift" function and CLR to delete all the input characters.
3 If the security method of the access point to be
connected is WEP, select "Default Key ID", select "OK"
and press ENTER.
„ Push Button: Use the automatic setting button of the
access point to establish connection.
1 Select "Push Button" with the cursor buttons and press
ENTER.
2 Hold down the automatic setting button of the access
point for the necessary seconds, select "OK" with the
cursor buttons and press ENTER.
Step 2: Setting Up
„ PIN code: Select this method when the automatic setting
button of the access point is beyond the reach. Select "PIN
code" with the cursor buttons and press ENTER to display
the 8-digit PIN code. Register the displayed PIN code to the
access point, select "OK" with the cursor buttons and press
ENTER. For how to register the PIN code to the access
point, refer to its instruction manual.
4. Establish connection.
The connection process starts and the Wi-Fi indicator
on the left of the unit's display starts flashing. When
connection has been established, the Wi-Fi indicator
changes from flashing to staying lit. If the Wi-Fi indicator
does not stay lit, connection has not been established.
Make the setting again. If "Push Button" does not work,
try "Enter Password".
4
HDMI Setup
The unit supports the linked system function such as power
on/off link when connected via HDMI cable with a CEC
(Consumer Electronics Control) compliant TV or player. You
need to change the initial setting to use the linked system
function, HDMI Through function and ARC (Audio Return
Channel) function.
z Operation: You can set up by viewing the guidance
displayed on the TV screen. To display the guidance, you
need to make HDMI connection between the unit and
TV. Select the item with the cursor buttons of the remote
controller and press ENTER to confirm your selection. To
return to the previous screen, press RETURN.
HDMI Through
The function allows transmission from players to the TV
even if the unit is in standby. Setting the HDMI CEC (RIHD)
setting mentioned above to "On" can enable this setting
automatically. It is also necessary to make the HDMI linked
system setting on the TV. See the TV's instruction manual
for details.
r Although enabling the HDMI Through function increases
power consumption during standby, the unit automatically
enters the HYBRID STANDBY mode that can minimize
the increase of power consumption by keeping only the
minimum circuits active.
ARC (Audio Return Channel)
5. Enjoy Internet radio or other sources.
Press HOME on the remote controller and select
"Network Service" in the Home menu. You can use a
variety of Internet services.
HDMI CEC (RIHD)
When the access point is not displayed
Select "Other..." with c on the remote controller and
press ENTER to display the keyboard screen. Input
the SSID and password. Make the following settings
according to the router setting.
„ WPA/WPA2 method
Select "WPA" or "WPA2" in "Security method", select
"OK" and press ENTER.
„ WEP method
Select "WEP" in "Security method", and select
"Default Key ID". Then select "OK" and press ENTER.
r If encryption setting has not been made on the
wireless LAN router, select "None" in "Security
method", select "OK" and press ENTER.
Simple connection to the ARC compatible TV using a
single HDMI cable allows to listen to the TV sound from the
speakers connected to the unit. To use the ARC function,
connect the unit to the ARC compatible HDMI jack of the
TV. Then, set the HDMI CEC (RIHD) mentioned above to
"On" on the unit, and make the following setting.
1. Press RCV on the remote controller and then press
HOME.
2. Select "Setup" with the cursor buttons and press
ENTER.
3. Select "11. HDMI Setup" with the cursor buttons and
press ENTER.
Turning the TV to standby mode will turn the unit to
„
standby mode.
On the TV side, it is possible to set whether to output
„
audio from the speakers connected to the unit or from
the TV's speakers.
Starting playback of a CEC compliant player/recorder will
„
automatically switch the unit's input to the HDMI input of
the player/recorder. If the unit is in standby mode, it will
automatically be turned on.
1. Press RCV on the remote controller and then press
HOME.
2. Select "Setup" with the cursor buttons and press
ENTER.
3. Select "11. HDMI Setup" with the cursor buttons and
press ENTER.
4. Select "HDMI CEC (RIHD)" with the cursor buttons
4. Select "Audio Return Ch" with the cursor buttons
and select "Auto".
Audio output of connected players
To enjoy digital surround sound including Dolby Digital
and DTS, audio output should be set to "Bitstream
output" on the connected blu-ray disc player or other
devices. If the TV does not support bitstream signals,
set the audio output to "PCM output" on the player to
listen to the audio from the TV's speakers. For how
to set the player, see the instruction manual of the
player. Some settings of the blu-ray disc player may
prevent reproduction of DTS-HD Master Audio. In
that case, turn "BD video supplementary sound" (or
secondary sound) to "Off" and try again.
and select "On".
9
Step 3: Playing Back
1
Playing the player and TV
Press RCV on the remote controller and press 1
zRECEIVER to turn the power on.
r Switch the input on the TV to that assigned to the unit.
Use the TV's remote controller.
2. Select the desired listening mode.
Press the 5 listening mode buttons to switch the mode
so that you can enjoy different listening modes. For
details about the listening modes, see "Listening modes"
on the next page.
3. Adjust the volume with 9.
mode.
2 REMOTE MODE/INPUT SELECTOR buttons: Switches
the input to be played.
3 Cursor buttons and ENTER button: Moves the cursor
2
7
8
1. Select the input of the unit and start playback on the
player or TV.
r Press 2 INPUT SELECTOR to which the desired
player has been assigned. Press TV/CD to play the
TV's sound. You can also use the input selector
buttons on the main unit.
r Input will automatically be selected if the TV or player
is CEC compliant and connected to the unit with
HDMI cable.
1 z RECEIVER button: Turns the unit on or into standby
1
9
3
4
F
G
and confirms the selection.
4 Q SETUP button: Displays the Quick Setup menu that
5
6
7
8
9
F
G
H
allows you to set the frequently used functions including
input selection and volume adjustment.
Listening mode buttons: Allows you to select the
listening mode.
DIMMER button: Switches the brightness of the display.
ZONE2 button: For use when the unit is connected with
a pre-main amplifier in a separate room and sound is
played there.
MUTING button: Temporarily mutes audio.
VOLUME buttons: Allows you to adjust the volume.
RETURN button: Returns the display to the previous state.
HOME button: Displays the Home menu that allows you to
make advanced settings and use Internet radio and DLNA.
DISPLAY button: Switches the information on the display.
„ How to use the remote controller
5
Remote controller parts name
6
H
Batteries (AA/R6)
Remote control sensor
z To control the unit: The remote controller may be in the
remote mode that enables control of other devices. Press
the 2 RCV button to select the RECEIVER mode (for
controlling this unit) before starting operation.
AV receiver
Approx.
16 ft. (5 m)
r If you do not use the remote controller for a long time,
remove the batteries to prevent leakage.
r Note that keeping consumed batteries inside may cause
corrosion resulting in damage of the remote controller.
10
Step 3: Playing Back
Listening modes
Select the desired mode by switching and listening actual
sound in different modes. The selectable listening modes
depend on the format of the input signals.
MOVIE/TV: You can select a listening mode suitable for
movies and TV programs.
MUSIC: You can select a listening mode suitable for music.
GAME: You can select a listening mode suitable for games.
„ Changing the Display Brightness: Press DIMMER on
the remote controller several times to select the desired
brightness. (North American and Taiwanese models)
„ Changing the Input Display: Press DISPLAY on the
remote controller several times to switch the display of the
main unit in order of:
Input source &
volume
FM STEREO
Listening
mode
PURE AUDIO (main unit only) (European, Australian
and Asian models): The display and analog video circuit is
cut off to provide purer sound.
r For details on the listening modes, see the Advanced
Manual (http://www.onkyo.com/manual/txnr535/adv/
en.html).
Other useful functions
„ Playing Video and Audio from Different Sources: It
is possible to play audio and video from different sources.
For example, you can play audio from the CD player and
video from the BD/DVD player. In this case, press BD/DVD
and then TV/CD. Then start playback on the BD/DVD player
and CD player. This function is effective when an input with
audio only has been selected (TV/CD, AM or FM in the
initial setting).
The automatic search for a radio station starts.
Searching stops when one is found. When tuned into a
radio station, the " TUNED " indicator on the unit's
display lights. The "FM STEREO" indicator lights if the
radio station is an FM radio station.
TUNED
AUTO
STEREO: You can select a listening mode for stereo and all
channel stereo sources.
"Direct" for playing the input signals as-is
Selecting this mode allows the input signals to be
played as they are. For example, 2 ch signals of music
CD will be played in stereo, 5.1 ch signals in 5.1 ch,
and Dolby Digital signals of blu-ray disc or DVD in the
Dolby Digital sound field according to the specified
number of channels.
3. Press TUNING on the unit.
Signal
format
Registering a Radio Station: It allows you to register up to
40 of your favorite AM/FM radio stations.
1. Tune into the AM/FM radio station you want to
register.
2. Press MEMORY on the unit.
The preset number on the unit's display flashes.
Sampling
frequency
r If "Dolby D 5.1" is displayed in signal format, the
Dolby Digital 5.1 ch signals are being input. When
listening to AM/FM radio, the band, frequency and
preset number are displayed.
2
Listening to AM/FM Radio
Auto tuning method is explained in Basic Manual. For more
details on AM/FM radio station, see Advanced Manual
(http://www.onkyo.com/manual/txnr535/adv/en.html).
1. Press AM or FM on the unit to select either "AM" or
"FM".
3. Repeatedly press
PRESET on the unit to select
a number between 1 and 40 while the preset number
is flashing (about 8 seconds).
4. Press MEMORY on the unit again.
When registered, the preset number stops flashing.
Repeat this procedure for all of your favorite AM/FM
radio stations. Press PRESET or CH +/- to select
the registered radio station.
3
Connecting and playing the Bluetoothenabled device
You can wirelessly enjoy music files stored in a smartphone
or other Bluetooth-enabled device. The coverage area is 48
feet (15 meters).
2. Press TUNING MODE on the unit so that the "AUTO"
indicator on the unit's display lights.
„ Muting Temporarily: Press MUTING on the remote
controller. Press MUTING again to cancel muting.
r The Bluetooth-enabled device needs to support the
A2DP profile.
r Note that connection is not always guaranteed with all
Bluetooth-enabled devices.
11
Step 3: Playing Back
Pairing
4
Using the Home menu
Pairing is necessary when using the Bluetooth-enabled
device for the first time. Before starting the procedure, learn
how to enable the Bluetooth setting function and to connect
with other devices on the Bluetooth-enabled device.
In the Home menu, you can make advanced settings and
use Internet radio and DLNA.
1. Press BLUETOOTH on the remote controller.
1. Press RCV on the remote controller and then press
The unit enters the pairing mode and the BLUETOOTH
indicator starts flashing.
2. While the BLUETOOTH indicator is flashing,
complete connection on the Bluetooth-enabled
device in the nearby area within about 2 minutes.
If the name of this unit is displayed on the Bluetoothenabled device's display, select this unit. Paring will end
after a short time.
r If a password is requested, enter "0000".
r When connecting the unit to any other Bluetoothenabled device, start pairing by pressing and holding
BLUETOOTH until the BLUETOOTH indicator starts
flashing. This unit can store the data of up to ten paired
devices.
Playing sound of the Bluetooth-enabled device
If the unit is on and the Bluetooth-enabled device is
connected, the input will be automatically switched to
BLUETOOTH. Play music in this state.
r It may take about a minute until connection is established
when the unit is on since the Bluetooth function takes
some time to start up.
r If the volume setting on the Bluetooth-enabled device is
low, the sound will not be output from this unit.
r Due to the characteristics of Bluetooth wireless
technology, the sound produced on this unit may slightly
be behind the sound played on the Bluetooth-enabled
device.
HOME.
The Home menu displays on the TV screen. You can
also use the HOME button on the main unit.
Home
Setup
Network Service
USB
Sleep Timer
InstaPrevue
2. Select the item with the cursor buttons of the
remote controller and press ENTER to confirm your
selection.
r For details on the Setup menu and how to play
Internet radio, DLNA and USB storage device, see
the Advanced Manual (http://www.onkyo.com/manual/
txnr535/adv/en.html).
r To return to the previous screen, press RETURN. To
return to the Home menu, press HOME.
5
Using Quick Setup menu
In the Quick Setup menu, you can set frequently used
functions including input selection and volume adjustment.
1. Press Q SETUP on the remote controller.
The Quick Setup menu is displayed on the connected
TV's screen.
Quick Setup
Input
Audio
Information
Listening Mode
„ Setup: You can change the assignment of input terminals
and input selector buttons and also make various speaker
settings and other advanced settings.
„ Network Service: Select to use various Internet radio
services and DLNA.
r "Network Setup" becomes selectable after the network
starts up even if it cannot be selected first. It may take
about a minute to start up.
„ USB: Select to connect a USB storage device to the USB
port so that it can be played.
r "USB" becomes selectable after the USB function starts
up even if it cannot be selected first. It may take about a
minute to start up.
„ Sleep Timer: Select to turn the unit into standby mode
automatically when the specified time elapses.
12
„ InstaPrevue: Select to preview videos input from the HDMI
input jacks collectively in a single screen. The screen has a
main window (current input video) and sub windows (other
input videos). To switch the current input, select the desired
sub window with the cursor buttons and press ENTER.
r A black sub window is shown for the input with no video
signals.
r "InstaPrevue" cannot be selected if the video is being
input from HDMI IN 6 or there is no signal from the input
currently selected.
r Depending on video signals, the picture may not be
properly rendered on the preview thumbnails.
2. Select the item with the cursor buttons of the
remote controller and press ENTER to confirm your
selection.
r To return to the previous screen, press RETURN.
„ Input: Select the input and check the assignment of input
selector buttons.
„ Audio:
A/V Sync: If the video is behind the audio, you can
delay the audio to offset the gap.
r It cannot be set when audio is played from the TV's
speakers.
r It cannot be set if the input is "NET", "USB" or
"BLUETOOTH".
r It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
Step 3: Playing Back
Bass, Treble: Adjust volume of the front speaker.
r It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
PM Bass (Phase Matching Bass): Suppress phase
shift in the midrange to enhance bass sound. Thus
smooth and powerful bass sound can be obtained.
r It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
Subwoofer Level, Center Level: Adjust the speaker
level while listening to the sound. The adjustment you
made will be reset to the previous status when you turn
the unit to standby mode.
r The speakers cannot be adjusted if they have been
set to "No" or "None" in "Sp Config".
AccuEQ: Disables the sound field correction settings
set in the automatic speaker setting. The setting can be
separately set to each input.
r The setting cannot be selected if the automatic
speaker setting has not been performed.
r It cannot be set if headphones are connected or the
listening mode is Pure Audio (European, Australian
and Asian models) or Direct.
Late Night: Make small sounds to be easily heard. It
is useful when you need to reduce the volume while
watching a movie late night. You can enjoy the effect
on Dolby Digital, Dolby Digital Plus and Dolby TrueHD
sources only.
r Turning the unit to standby mode will set the setting
to "Off". In case of Dolby TrueHD, the setting will be
set to "Auto".
„ Information: Display the audio information.
Performing ZONE playback
„ Listening Mode: Select the listening mode from the
categories of "MOVIE/TV", "MUSIC" and "GAME".
r It cannot be set when audio is played from the TV's speakers.
1. Press ZONE2 on the remote controller, point the
6
Using the ZONE function
You can connect the unit with a pre-main amplifier in
a separate room and play the sound from the device
connected to the unit via analog connection or from the
"NET", "USB" or "BLUETOOTH" source. It is also possible
to play the sound from different analog connected devices
in the main room and separate room.
r As for the "NET", "USB" and "BLUETOOTH", you cannot select
different inputs for the main room and separate room. For
example, if "NET" has been selected in the main room and then
"USB" is selected on the pre-main amplifier in the separate room,
the input in the main room will change to "USB" accordingly.
r When listening to AM/FM broadcasting, you cannot select
different stations for the main room and separate room. Therefore
broadcasting of the same station will be heard in the both rooms.
Making ZONE connection
Connect the ZONE 2 LINE OUT jacks of the unit and the
line-in jacks of the pre-main amplifier in a separate room
with an analog audio (RCA) cable.
remote controller at the remote controller sensor
and press zRECEIVER.
"Z2" lights on the unit and the ZONE function is enabled.
(ZONE 2 is now on.)
2. Press ZONE2 on the remote controller again and
press INPUT SELECTOR of the input to be played in
a separate room.
To play the same source in the main room and separate
room, hold down ZONE2 for approximately 3 seconds.
The volume should be adjusted with the pre-main
amplifier used in the separate room.
¼
To control ZONE playback on the main unit, press ZONE2 and within 8
seconds, press the input selector button of the input to be played in a
separate room. To play the same source in the main room and separate
room, press ZONE2 twice. "Z2 : Source" appears on the unit's display.
To turn off the ZONE function: Press ZONE2 on the
remote controller and press zRECEIVER. Alternatively
press OFF on the main unit.
r If ZONE 2 is on, power consumption during standby
becomes larger than normal.
r If ZONE 2 is turned on when the listening mode of the
main room is Pure Audio, it will automatically switch to
Direct. (European, Australian and Asian models)
r While ZONE 2 is on, the RI linked system function
(interlink between Onkyo components) is disabled.
Music Optimizer : Improve the quality of the
compressed audio. Playback sound of lossy
compressed files such as MP3 will be improved. The
setting can be separately set to each input.
r The setting is effective in the signals of 48 kHz or
less. The setting is not effective in the bitstream
signals.
r It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
Cinema Filter: Adjust the soundtrack that was
processed to enhance its high pitch range, in order to
make it suitable for home theater.
r This function can be used in the following listening
modes: Multichannel, Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio, DTS Express, DTS 96/24,
Dolby PL II Movie, and Neo:6 Cinema.
13
Parts Name
1
2
3 4
56
7
8
9
N
G
H
I
J
K
L
(European, Australian
and Asian models)
(European, Australian
and Asian models)
M
F
O
P
Q
R
S
T
Front Panel
1 zON/STANDBY button: Turns the unit on or into
2
3
4
5
6
7
8
9
standby mode.
BLUETOOTH indicator: Flashes while pairing with a
Bluetooth-enabled device is in progress and stays lit
when pairing is completed.
ZONE 2 button: Controls the ZONE function.
Wi-Fi indicator: Lights when the unit is connected to
the wireless LAN router.
Remote control sensor: Receives signals from the
remote controller.
OFF button: Switches the ZONE function to off.
Display
Listening mode buttons: Allows you to select the
listening mode.
DIMMER button (North American and Taiwanese
models): Switches the brightness of the display.
RT/PTY/TP button (European, Australian and Asian
models): Can be used when receiving the station
transmitting text information.
14
F MEMORY button: Registers or deletes a station.
G TUNING MODE button: Switches the tuning mode.
H DISPLAY button: Switches the information on the
display.
I HOME button: Displays the Home menu.
J Cursor buttons, lTUNINGj button, dPRESETc
button and ENTER button: Moves the cursor and
confirms the selection. When listening to AM/FM
broadcasting, tune in to the station with lTUNINGj or
select the registered station with dPRESETc.
K RETURN button: Returns the display to the previous
state.
L MASTER VOLUME: Allows you to adjust the volume.
M MUSIC OPTIMIZER button and indicator (North
American and Taiwanese models): Turns on/off the
MUSIC OPTIMIZER function that improves the quality of
the compressed audio.
PURE AUDIO button and indicator (European,
Australian and Asian models): Switches to the PURE
AUDIO mode.
N PHONES jack: Stereo headphones with a standard plug
are connected.
O TONE and Tone Level buttons: Adjusts the high tone
and low tone.
P Input selector buttons: Switches the input to be
played.
Q AUX INPUT AUDIO/VIDEO jacks: A video camera or
such other device is connected.
R USB port: A USB storage device is connected so that
music files stored in it can be played.
S SETUP MIC jack: The supplied speaker setup
microphone is connected.
T HYBRID STANDBY indicator: Lights if the unit enters
standby mode when the HDMI Through, network
standby or Wakeup from Bluetooth function is enabled.
Parts Name
1
2
3
4
6
5
7
1 23
4
5
9
6
7
8
Display
1 Lights in the following conditions. "Z2": ZONE 2 output
(Taiwanese model)
8
9
F
G H
is on. / "HDMI": HDMI signals are input and HDMI input
selector is selected. / "ARC": Audio signals are input
from ARC compatible TV and TV/CD input selector
is selected. / "3D": Input signals are 3D. / "USB" (¼):
"USB" input is selected and USB storage device is
connected. / "NET" (¼): "NET" input is selected and
the unit is connected to the network. / "DIGITAL":
Digital signals are input and the digital input selector is
selected. / Cursor indicators: NET or USB is controlled.
¼
"USB" and "NET" will flash if the connection is not correct.
Rear Panel
1 RI REMOTE CONTROL jack: An Onkyo product with RI
2
3
4
5
6
7
8
9
F
jack can be connected and synchronized with this unit.
(/#06'00#LCEM
ŝCPF#/#06'00#
terminal: The supplied antennas are connected.
COMPONENT VIDEO IN and OUT jacks: Component
video input/output jacks
ETHERNET port: Used for LAN connection
HDMI IN/OUT jacks: Digital video signals and audio
signals are transmitted between the unit and the
connected devices.
SPEAKERS terminals: Speakers are connected.
Power cord (North American, European, Australian
and Asian models)
AC INLET (Taiwanese model): The power cord is
connected.
DIGITAL IN COAXIAL/OPTICAL jacks: Digital audio
signals are input.
Composite video and analog audio jacks: Analog
video signals and audio signals are input.
MONITOR OUT V jack: Video signals are output to the
connected monitor or TV.
G ZONE 2 LINE OUT jacks: Analog audio signals are
output to the connected amplifier to be used in ZONE 2.
H SUBWOOFER PRE OUT jacks: A subwoofer with builtin amplifier is connected.
2 Lights when headphones are connected.
3 Lights when NET or USB is controlled.
4 Lights according to the type of input digital signals and
the listening mode.
5 Lights when Music Optimizer is enabled.
6 Lights in the following conditions. "AUTO": Tuning mode
is auto. / "fTUNEDe": Receiving AM/FM radio. fe
flashes while tuning is automatically performed. / "FM
STEREO": Receiving FM stereo. / "RDS" (European,
Australian and Asian models): Receiving RDS
broadcasting.
7 "MUTING": Flashes when muting is on.
8 Lights in the following conditions. "SLEEP": Sleep timer
has been set. / "ASb" (Auto Standby): Auto Standby
is on. / "ch": Channel is being set. / "Hz": Crossover
frequencies are being set. / "m/ft": Speaker distances
are being set. / "dB": Speaker volume is being set.
9 Displays various information of the input signals.
Pressing DISPLAY displays the type of input digital
signals and the listening mode.
15
Troubleshooting
The AV receiver turns off unexpectedly.
r The AV receiver will automatically enter standby mode
when Auto Standby is set and launched.
There’s no sound, or it’s very quiet.
r A wrong input selector button has been selected. Select
a correct input for the player. Also check that muting is
not on.
r Not all listening modes use all speakers.
There’s no picture.
r A wrong input selector button has been selected.
r There will be no video output, if the listening mode is
Pure Audio. (European, Australian and Asian models)
r To display video from the connected player on the TV
screen while the unit is in standby, you need to enable
"HDMI Through".
r When the TV image is blurry or unclear, power code or
connection cables of the unit may have interfered. In
that case, keep distance between TV antenna cable and
cables of the unit.
HDMI control does not function correctly.
r Set the HDMI CEC (RIHD) setting of the unit to "On". It is
also necessary to make the HDMI linked system setting
on the TV. See the TV's instruction manual for details.
ovens, game consoles, etc.). If this does not solve
the problem, stop using other devices which emit
electromagnetic waves.
r When other wireless LAN devices are used near the AV
receiver, several issues such as interrupted playback
and communication may occur. You can avoid these
issues by changing the channel of your Wi-Fi router. For
instructions on changing channels, see the instruction
manual provided with your Wi-Fi router.
r If there is a metallic object near the AV receiver, wireless
LAN connection may not be possible as the metal can
effect on the radio wave.
r If there is more than one access point in the network,
separate each access point.
Bluetooth
r Try plugging/unplugging the unit and the Bluetoothenabled player. After that, check that the Bluetooth
function is enabled on the Bluetooth-enabled device and
the connection with the unit has been established.
„ Before requesting a service
If the methods listed above cannot solve your problem, try
plugging/unplugging the power cord and connection cables
of the unit and/or reset the unit status. If you reset the unit
status, your preferences will be reset to the defaults. Note
them down before starting reset.
z How to reset: Perform steps 1 and 2 below. "Clear" will
appear on the display and the unit returns to standby.
Clear
2. Press zON/STANDBY. 1. Hold down CBL/SAT,
z How to initialize the remote controller: To initialize the
remote controller to its factory defaults, while holding down
RCV, press and hold HOME until the remote indicator lights
(about 3 seconds). Within 30 seconds, press RCV again.
RCV
Remote
indicator
The remote controller does not work.
r Be sure to press RCV first before operating the unit with
the remote controller.
HOME
Cannot access to network.
r Try plugging/unplugging the unit or the wireless LAN
router or check their power-on status. This will work well
in many cases.
r If the desired wireless LAN router is not in the access
point list, it may be set to hide SSID or the ANY
connection may be off. Change the setting and try again.
r Place the AV receiver away from the devices emitting
electromagnetic waves on the 2.4 GHz band (microwave
16
Specifications
Amplifier Section
Rated Output Power
All channels:
65 watts minimum continuous power per channel,
8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a
maximum total harmonic distortion of 0.7% (FTC)
90 watts minimum continuous power per channel, 6 ohm loads, 2
channels driven at 1 kHz, with a maximum total harmonic distortion
of 0.7% (FTC)
(North American)
5 ch × 100 W at 6 ohms, 1 kHz,
1 ch driven of 1% (IEC) (Others)
Maximum Effective Output Power
5 ch × 120 W at 6 ohms, 1 kHz,
1 ch driven (JEITA)
(Asian)
Dynamic Power (¼)
¼IEC60268-Short-term maximum output power
9
ŝ(TQPV
9
ŝ(TQPV
9
ŝ(TQPV
THD+N (Total Harmonic Distortion+Noise)
0.7% (20 Hz - 20 kHz, half power)
Damping Factor
(TQPVM*\ŝ
Input Sensitivity and Impedance (Unbalance)
O8Mŝ
.+0'
Rated RCA Output Level and Impedance
O8Mŝ
.+0'176
Maximum RCA Output Level and Impedance
8Mŝ
.+0'176
Frequency Response
5 Hz - 100 kHz/+1 dB, –3 dB (Direct mode)
Tone Control Characteristics
±10 dB, 20 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio
100 dB (LINE, IHF-A)
Speaker Impedance
ŝŝ
Video Section
Input Sensitivity/Output Level and Impedance
8RRŝ
%QORQPGPV;
8RRŝ
%QORQPGPV2B/CB, PR/CR)
8RRŝ
%QORQUKVG
Component Video Frequency Response
5 Hz - 100 MHz/+0 dB, –3 dB
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz
(North American and Taiwanese)
87.5 MHz - 108.0 MHz, RDS (Others)
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel
40
Network Section
Ethernet LAN
10BASE-T/100BASE-TX
Wireless LAN
IEEE 802.11 b/g/n standard
(Wi-Fi® standard)
2.4 GHz band:
1 - 11 ch (North American)
10 - 11 ch (Spain)
10 - 13 ch (France)
1 - 13 ch (Others)
(Wi-Fi® standard)
Bluetooth Section
Dimensions (W × H × D)
435 mm × 150 mm × 329 mm
17-1/8" × 5-7/8" × 12-15/16"
Weight
7.6 kg (16.8 lbs.) (North American and Taiwanese)
8.1 kg (17.9 lbs.) (Others)
„ HDMI
Input
IN1 (BD/DVD), IN2 (CBL/SAT), IN3 (STB/DVR), IN4 (GAME), IN5 (PC),
IN6
Output
OUT
Video Resolution
4K 60 Hz (YCbCr 4:2:0)
Audio Format
DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD,
Dolby Digital Plus, DSD, Multichannel PCM
Supported
3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD),
4K Passthrough
Communication system
Bluetooth Specification version 2.1 +EDR (Enhanced Data Rate)
Maximum communication range
Line of sight approx. 15 m (*)
Frequency band
2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible Bluetooth profiles
A2DP 1.2 (Advanced Audio Distribution Profile)
AVRCP 1.3 (Audio Video Remote Control Profile)
Supported Codecs
SBC
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
¼
The actual range will vary depending on factors such as obstacles between
devices, magnetic fields around a microwave oven, static electricity, cordless
phone, reception sensitivity, antenna’s performance, operating system,
software application, etc.
„ Video Inputs
General
Analog
ZONE2 LINE OUT
2 SUBWOOFER PRE OUT
Speaker Outputs
FRONT L/R, CENTER, SURROUND L/R
Phones
PHONES (Front, ø 6.3)
Power Supply
AC 120 V, 60 Hz (North American and Taiwanese)
AC 230 V, 50 Hz (European, Australian and British)
AC 220 - 240 V, 50/60 Hz (Others)
Power Consumption
3.2 A (North American and Taiwanese)
330 W (European, Australian and British)
380 W (Others)
0.1 W (Stand-by, North American and Taiwanese)
0.2 W (Stand-by, Others)
55 W (No-sound)
Component
IN (CBL/SAT)
Composite
IN1 (CBL/SAT), IN2 (STB/DVR), IN3 (GAME), AUX
„ Video Outputs
Component
OUT
Composite
MONITOR OUT
„ Audio Inputs
Digital
OPTICAL (TV/CD)
COAXIAL 1 (BD/DVD), 2 (CBL/SAT)
Analog
BD/DVD, CBL/SAT, STB/DVR, GAME, PC, TV/CD, AUX
„ Audio Outputs
„ Others
Setup Mic
RI
USB
Ethernet
1 (Front)
1
1 (Front)
1
Specifications and features are subject to change without notice.
17
License and Trademark Information
InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks
of Silicon Image, Inc. in the United States and other countries.
Precautions
Apple, iPod and iPhone are trademarks of Apple Inc., registered in the U.S. and
other countries.
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the
double-D symbol are trademarks of Dolby Laboratories.
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the
Symbol, & DTS and the Symbol together are registered trademarks of DTS,
Inc. © DTS, Inc. All Rights Reserved.
Apple TV is a trademark of Apple Inc., registered in the U.S. and other
countries.
SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio
Inc. and its subsidiaries. All rights reserved.
DLNA ®, the DLNA Logo and DLNA CERTIFIED ® are trademarks, service
marks, or certification marks of the Digital Living Network Alliance.
This product is protected by certain intellectual property rights of Microsoft. Use
or distribution of such technology outside of this product is prohibited without a
license from Microsoft.
"CINEMA FILTER" and "CINEMA FILTER (logo)" are trademarks of Onkyo
Corporation.
Windows and the Windows logo are trademarks of the Microsoft group of
companies.
AccuEQ, Music Optimizer, RIHD and WRAT are trademarkds of Onkyo
Corporation.
QR Code is a registered trademark of DENSO WAVE INCORPORATED.
"RIHD" and "RIHD (logo)" are trademarks of Onkyo Corporation.
Safari is a trademark or registered trademark of Apple Computer, Inc. in the US
and other countries.
"x.v.Color" is a trademark of Sony Corporation.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
Thomson.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
The Wi-Fi CERTIFIED ® Logo is a certification mark of the Wi-Fi Alliance.
Wi-Fi certified ® logo shows international association certifying interoperability
"Wi-Fi alliance" ensures the product has passed the test for compatibility with
other Wi-Fi certified equipment.
The Bluetooth ® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Onkyo is under license.
Other trademarks and trade names are those of their respective owners.
Onkyo does not guarantee Bluetooth compatibility between the AV receiver and
all Bluetooth-enabled devices.
For compatibility between the AV receiver and another device with Bluetooth
technology, consult the device’s documentation and dealer. In some countries,
there may be restrictions on using Bluetooth devices. Check with your local
authorities.
18
"All other trademarks are the property of theirrespective owners."
For European Models
Declaration of Conformity
We declare, under our sole responsibility, that this
product complies with the standards:
– Safety
– Limits and methods of measurement of radio
disturbance characteristics
– Limits for harmonic current emissions
– Limitation of voltage changes, voltage fluctuations and flicker
– RoHS Directive, 2011/65/EU
– Hereby, Onkyo Corporation, declares that this TX-NR535 is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC.
– µÑÄÕÖÒãÝÉÖÒ2QN\R&RUSRUDWLRQÈÉÎÏÄÔÌÔÄÛÉ7;15ÉÆ
ÕÞÒÖÆÉÖÕÖÆÌÉÕÞÕÕÞÝÉÕÖÆÉÑÌÖÉÌËÌÕÎÆÄÑÌãÌÈÔ×ÇÌÖÉÓÔÌÏÒÊÌÐÌ
ÔÄËÓÒÔÉÈÅÌÑĨÌÔÉÎÖÌÆÄ(&
– 1PM[Q%QTRQTCVKQPVÉOVQRTQJNCwWLGzG6:04URNĢWLG\½MNCFPÉ
RQzCFCXM[CXwGEJPCRįÉUNWwP½WUVCPQXGPK5OøTPKEG'5
– Undertegnede Onkyo Corporation erklærer herved, at følgende udstyr TXNR535 overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
– Hiermit erklärt Onkyo Corporation, dass sich das Gerät TX-NR535 in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
– Käesolevaga kinnitab Onkyo Corporation seadme TX-NR535 vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele
teistele asjakohastele sätetele.
– ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ Onkyo Corporation ΔΗΛΩΝΕΙ
ΟΤΙ TX-NR535 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ
ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
– Por la presente, Onkyo Corporation, declara que este TX-NR535 cumple
con los requisitos esenciales y otras exigencias relevantes de la Directiva
1999/5/EC.
– Par la présente, Onkyo Corporation déclare que l’appareil TX-NR535 est
conforme aux exigences essentielles et aux autres dispositions pertinentes
de la directive 1999/5/CE.
– Con la presente Onkyo Corporation dichiara che questo TX-NR535 è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.
– #TwQ1PM[Q%QTRQTCVKQPFGMNCTðMC6:04CVDKNUV&KTGMVĈXCU
'-DĿVKUMCLÞORTCUĈDÞOWPEKVKGOCTVQUCKUVĈVCLKGOPQVGKMWOKGO
– Šiuo Onkyo Corporation deklaruoja, kad šis TX-NR535 atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
– A Onkyo Corporation ezzennel kijelenti, hogy a TX-NR535 típusú berenFG\ÅUVGNLGUÉVKC\CNCRXGVĩMÒXGVGNOÅP[GMGVÅUO½U'-KT½P[GNXDGP
OGIJCV½TQ\QVVXQPCVMQ\ÏTGPFGNMG\ÅUGMGV
– Hierbij verklaart Onkyo Corporation dat het toestel l TX-NR535 in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
– 0KPKGLU\[O1PM[Q%QTRQTCVKQPFGMNCTWLGŏG6:04LGUV\IQFP[
\\CUCFPKE\[OKY[OCICPKCOKKKPP[OKYĜCıEKY[OKRQUVCPQYKGPKCOK
Dyrektywy 1999/5/EC.
– Eu, Onkyo Corporation, declaro que o TX-NR535 cumpre os requisitos
essenciais e outras provisões relevantes da Directiva 1999/5/EC.
– 2TKPRTG\GPVC1PM[Q%QTRQTCVKQPFGENCTàEàCRCTCVWN6:04GUVG
ÊPEQPHQTOKVCVGEWEGTKPķGNGGUGPķKCNGĵKEWCNVGRTGXGFGTKRGTVKPGPVGCNG
Directivei 1999/5/CE.
– 1PM[Q%QTRQTCVKQPVÙOVQX[JNCUWLGzG6:04CURĔĢC\½MNCFPÅ
RQzKCFCXM[CXwGVM[RTÉUNWwPÅWUVCPQXGPKC5OGTPKEG'5
– Onkyo Corporation izjavlja, da je ta TX-NR535 v skladu z bistvenimi
\CJVGXCOKKPFTWIKOKTGNGXCPVPKOKFQNQêKNKFKTGMVKXG'5
– Onkyo Corporation vakuuttaa täten että TX-NR535 tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
– *ÀTOGFHÒTMNCTCT1PM[Q%QTRQTCVKQPCVVFGPPC6:04HÒNLGTFG
väsentliga kraven och andra relevanta stadgar i Direktiv 1999/5/EC.
– Hér með lýsir Onkyo Corporation því yfir að varan TX-NR535 er í samræmi
XKÌITWPPMTÒHWTQICÌTCTMTÒHWTUGOIGTÌCTGTWÉVKNUMKRWP'%
– Onkyo Corporation erklærer herved at denne TX-NR535 er i
overensstemmelse med vesentlige krav og andre relevante bestemmelser i
direktiv 1999/5/EC.
– 1XKOG1PM[Q%QTRQTCVKQPRQVXTîWLGFCLG6:04WUWINCUPQUVKUC
osnovnim zahtjevima i ostalim relevantnim odredbama Direktive 1999/5/EC.
19
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku, OSAKA 541-0041, JAPAN
http://www.onkyo.com/
The Americas
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
Europe
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
Meridien House, Ground floor, 69 - 71 Clarendon Road, Watford, Hertfordshire, WD17 1DS, United Kingdom
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95
China
(Hong Kong)
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.hk.onkyo.com/
(Mainland)
1301, 555 Tower, No.555 West NanJing Road, Jing’an District, Shanghai, China 200041,
Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
Asia, Oceania, Middle East, Africa
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
http://www.intl.onkyo.com/support/
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
D1402-0
SN 29401733
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 7 3 3 *
Support for Spotify Connect
„
Spotify Connect can be supported by updating the unit's
firmware. Simply click the Connect icon and select the unit
on the playback screen of Spotify application to enjoy high
quality music streaming. To enable Spotify Connect, install
the Spotify application on your smartphone or tablet first.
Then, create a Spotify premium account.
The Spotify software is subject to third party licenses found here:
¼
www.spotify.com/connect/third-party-licenses
Notes for using multi-zone function
To enjoy Spotify music in a separate room, select "NET"
as the input of the separate room.
Volume adjustment with the Spotify application is
possible only for the equipment connected to the
ZONE2/3 speaker terminals (compatible model only).
If any other terminal is used for connection, adjust the
volume on the audio equipment placed in a separate
room.
To enjoy Spotify music in the main room after playing
Spotify in a separate room, select "NET" as the input of
the main room.
Auto Power On
Turning network standby on allows you to use the Auto
Power On function when using the Spotify application.
Si un autre type de borne est utilisé pour la connexion,
réglez le volume sur l'équipement audio placé dans une
pièce séparée.
Afin de profiter de la musique Spotify dans la pièce
principale après la lecture de Spotify dans une pièce
UÅRCTÅGUÅNGEVKQPPG\‡|0'6|—|EQOOGGPVTÅGFGNC
pièce principale.
Mise sous tension automatique
La mise en veille du réseau vous permet d'utiliser la
fonction de mise sous tension automatique lors de
l'utilisation de l'application Spotify.
Spotify Connect peut être pris en charge par la mise à
jour du logiciel de l'unité. Cliquez simplement sur l'icône
Connect et sélectionnez l'unité sur l'écran de lecture de
l'application Spotify pour profiter de la diffusion audio
de haute qualité. Pour activer Spotify Connect, installez
l'application Spotify sur votre smartphone ou tablette en
premier. Puis, créez un compte premium Spotify.
Le logiciel Spotify est soumis à des licences de tiers que vous trouverez ici :
¼
www.spotify.com/connect/third-party-licenses
Spotify Connect può essere supportato tramite
l’aggiornamento del firmware dell’unità. È sufficiente
cliccare sull’icona Connect e selezionare l’unità sulla
schermata di riproduzione dell’applicazione Spotify per
fruire di streaming di musica ad alta qualità. Per abilitare
Spotify Connect, installare anzitutto l’applicazione Spotify
sul proprio smartphone o tablet. Quindi, creare un account
premium Spotify.
Il software Spotify è soggetto a licenze di terze parti presenti all’indirizzo:
¼
www.spotify.com/connect/third-party-licenses
Note per l’utilizzo della funzione multi-zona
Compatibilidad con Spotify Connect
„
Spotify Connect será compatible mediante la actualización
del firmware de la unidad. Simplemente haga clic en
el icono Connect y seleccione la unidad en la pantalla
de reproducción de la aplicación Spotify para disfrutar
de transmisión de música de alta calidad. Para habilitar
Spotify Connect, instale primeramente la aplicación Spotify
en su teléfono inteligente o tableta. A continuación, cree
una cuenta Spotify premium.
El software de Spotify está protegido por licencias de terceros que
¼
encontrará en:
www.spotify.com/connect/third-party-licenses
Notas sobre el uso de función multizona
Support pour Spotify Connect
„
Supporto per Spotify Connect
„
Para disfrutar de la música de Spotify en otra habitación,
seleccione “NET” como la entrada de dicha habitación.
Con la aplicación Spotify podrá ajustar el volumen
solamente del equipo conectado a los terminales del
altavoz ZONE2/3 (únicamente modelos compatibles).
Si usa cualquier otro terminal para la conexión, ajuste
el volumen en el equipo de audio ubicado en dicha
habitación independiente.
Para disfrutar de la música de Spotify en la habitación
principal después de reproducirla en otra habitación
Spotify, seleccione “NET” como la entrada de la
habitación principal.
Per fruire di musica Spotify in una stanza separata,
selezionare “NET” come ingresso della stanza separata.
La regolazione del volume con l’applicazione Spotify è
possibile solo per l’apparecchiatura collegata ai terminali
dell’altoparlante ZONE2/3 (solo modello compatibile).
Se viene utilizzato qualsiasi altro terminale per il
collegamento, regolare il volume sull’apparecchiatura
audio posizionata in una stanza separata.
Per fruire di musica Spotify nella stanza principale
dopo aver riprodotto Spotify in una stanza separata,
selezionare “NET” come ingresso della stanza
principale.
Accensione automatica
L’attivazione dello standby di rete consente di utilizzare
la funzione di accensione automatica quando si utilizza
l’applicazione Spotify.
Remarques concernant la fonction multizone
Pour profiter de la musique Spotify dans une pièce
UÅRCTÅGUÅNGEVKQPPG\‡|0'6|—|EQOOGGPVTÅGFGNC
pièce séparée.
Le réglage du volume avec l'application Spotify n'est
possible que pour l'équipement connecté aux bornes
d'enceintes ZONE2/3 (modèle compatible seulement).
Activación automática
Activar el modo de espera de red le permite usar la
función de activación automática al utilizar la aplicación
Spotify.
D1410-0
SN 29402014
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
Unterstützung für Spotify Connect
„
Spotify Connect kann durch Aktualisierung der Firmware
des Geräts unterstützt werden. Klicken Sie einfach auf
das Symbol Connect und wählen Sie das Gerät auf
dem Wiedergabe-Bildschirm der Anwendung Spotify,
um hochqualitatives Musik-Streaming zu genießen. Zur
Aktivierung von Spotify Connect, installieren Sie die
Anwendung Spotify zuerst auf Ihrem Smartphone oder
Tablet. Erstellen Sie dann einen Spotify Premium-Account.
Die Software Spotify benötigt Lizenzen dritter Parteien, die Sie hier finden:
¼
www.spotify.com/connect/third-party-licenses
Hinweise zur Verwendung der Multizonenfunktion
Zum Genuss von Spotify Musik in einem anderen Raum,
wählen Sie „NET“ als Eingang für den anderen Raum aus.
Lautstärken-Einstellung mit der Anwendung
Spotify ist nur für Ausrüstung möglich, die mit den
Lautsprecheranschlüssen ZONE2/3 verbunden ist (nur
kompatibles Modell). Wird für die Verbindung ein anderer
Anschluss verwendet, passen Sie die Lautstärke an
der Audio-Ausrüstung an, die in einem anderen Raum
platziert ist.
Zum Genuss von Spotify Musik im Hauptraum nach dem
Abspielen von Spotify in einem anderen Raum, wählen
Sie „NET“ als Eingang für den Hauptraum aus.
Auto Power Ein
Einschalten von Netzwerk-Standby ermöglicht Ihnen die
Verwendung der Auto Power Ein-Funktion, wenn Sie die
Anwendung Spotify verwenden.
Ondersteuning voor Spotify Connect
„
Spotify Connect kan worden ondersteund door de
firmware van het toestel bij te werken. Klik simpelweg op
het pictogram Connect en selecteer het toestel op het
weergavescherm van de Spotify-toepassing om te genieten
van hoogwaardige muziekstreaming. Om Spotify Connect
in te schakelen, installeert u eerst de Spotify-toepassing op
uw smartphone of tablet. Maak vervolgens een premium
account voor Spotify.
De software van Spotify is onderworpen aan licenties van derde partijen
¼
die u hier terugvindt:
www.spotify.com/connect/third-party-licenses
Opmerkingen voor gebruik van de multi-zonefunctie
Om te genieten van muziek van Spotify in een aparte
ruimte, selecteert u „NET” als de invoer van de aparte
ruimte.
Volumeregeling met de Spotify-toepassing is alleen
mogelijk voor de apparatuur verbonden met de
ZONE2/3-luidsprekeraansluitingen (alleen compatibel
model). Als een andere aansluiting wordt gebruikt
voor de verbinding, regel het volume dan op de
audioapparatuur in een aparte ruimte.
Om te genieten van muziek van Spotify in de
hoofdruimte na het afspelen van Spotify in een
aparte ruimte, selecteert u „NET” als de invoer van de
hoofdruimte.
Automatisch Inschakelen Aan
Als u het netwerk in stand-by zet, kunt u de functie
Automatisch Inschakelen Aan gebruiken wanneer u de
Spotify-toepassing gebruikt.
Stöd för Spotify Connect
„
Spotify Connect stöds genom att uppdatera enhetens
firmware. Klicka på Connect-ikonen och välj enheten
på Spotify-applikationens uppspelningsskärm för
att njuta av högkvalitativ musik-streaming. För att
aktivera Spotify Connect, måste du först installera
Spotify-applikationen på din smartphone eller surfplatta.
Skapa sedan ett Spotify-premiumkonto.
Spotify-programvaran omfattas av tredjepartslicenser som kan hittas här:
¼
www.spotify.com/connect/third-party-licenses
Anmärkningar för användning av
multizonsfunktionen
För att uppleva Spotify-musik i ett annat rum, välj ”NET”
som inmatning för det andra rummet.
Justering av volymen för Spotify-applikationen är
endast möjlig för utrustningen som är ansluten till
ZONE2/3-högtalarkontakterna (endast kompatibla
modeller). Om någon annan kontakt används för
anslutningen, justera volymen på ljudutrustningen i det
andra rummet.
För att uppleva Spotify-musik i huvudrummet efter att
du har spelat Spotify i ett annat rum, välj ”NET” som
ingångskälla för huvudrummet.
Automatiskt strömpåslag
Genom att slå på nätverks-standby kan du använda
funktionen för automatiskt strömpåslag när du använder
Spotify-applikationen.
Spotify Connect -tuki
„
Spotify Connect voidaan tukea päivittämällä laitteen
ohjelmisto. Napsauta Connect-kuvaketta ja valitse
laite Spotify-sovelluksen toistonäytössä nauttiaksesi
korkealaatuisesta musiikin suoratoistosta. Ota
Spotify Connect käyttöön asentamalla Spotify-sovellus
ensin älypuhelimeesi tai tablettiisi. Luo sitten Spotify
Premium -tili.
Spotify-ohjelmistoon sovelletaan kolmannen osapuolen lisenssejä, jotka
¼
löytyvät täältä:
www.spotify.com/connect/third-party-licenses
Huomautuksia monivyöhyketoiminnon käytöstä
Nauti Spotify-musiikista erillisessä huoneessa
valitsemalla erillisen huoneen tulolähteeksi ”NET”.
Äänenvoimakkuuden säätö Spotify-sovelluksella
on mahdollista vain laitteella, joka on kytketty
ZONE2/3-kaiutinliitäntään (vain yhteensopiva malli). Jos
jotain muuta kaiutinpäätettä käytetään kytkemisessä,
säädä äänenvoimakkuutta äänentoistolaitteesta joka
sijaitsee erillisessä huoneessa.
Kun haluat nauttia Spotify-musiikista päähuoneessa
sen jälkeen kun Spotify-musiikkia on toistettu erillisessä
huoneessa, valitse ”NET” tulolähteeksi päähuoneessa.
Automaattinen virta päälle -toiminto
Kytkemällä verkon valmiustilan päälle voit käyttää
automaattista virta päälle -toimintoa, kun käytät
Spotify-sovellusta.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising