Samsung | SCD-2060E | User manual | Samsung SCD-2060E User manual

Samsung SCD-2060E User manual
High Resolution Varifocal
Dome Camera
User Manual
SCD-2060E
B
T
■
■
High Resolution Varifocal Dome Camera
User Manual
Copyright
©2010 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on
the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document
without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
Before operating the camera, confirm the camera model and correct input power voltage.
To help you understand this manual thoroughly, we’ll introduce our model description.
■ SCD-2060E SERIES
• NTSC MODEL
SCD-2060EN
• PAL MODEL
SCD-2060EP
■ MODEL DESCRIPTION
• SCD-2060EX_
SIGNAL SYSTEM
• SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
safety information
6
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
7
8
9
1
C
WARNING
• To prevent damage which may result in fire or electric shock hazard, do not expose this
appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
1
2
3
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
4
5
6
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
7
4. Securely plug the power cord into the power receptacle. insecure connection may cause
fire.
8
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.
9
4_ safety information
1
e
e
7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or
electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. in such case,
immediately disconnect the power source and contact the service center. continued use in
such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. never
disassemble or modify this product in any way. (samsung is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. doing so may cause
fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibrationor magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below
-10°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so
may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD.
English_5
● SAFETY INFORMATION
c
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers
filled with water on top of the camera. doing so may cause personal injury due to fire,
electric shock, or falling objects.
safety information
im
FCC STATEMENT
1
2
3
4
5
6
7
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause
undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
8
9
1
1
1
1
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
6_ safety information
1
o
e
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the
cart/ apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
1.
2.
3.
4.
5.
6.
7.
t
e
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products.The Eco mark represents
Samsung Techwin’s will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
English_7
● SAFETY INFORMATION
e
important safety instructions
contents
in
INTRODUCTION
9
INSTALLATION
12
CONNECTION
16
SETUP
18
TROUBLESHOOTING
9
10
11
Features
What’s included
Component names and functions
F
12
15
Installation
Adjust the panning and tilting
while watching the monitor
y
y
16
16
17
Connecting to Monitor
Connecting to Power
Using Coaxial Communications
32
8_ contents
y
y
18
18
Menu Configuration
Menu Setup
y
31
Troubleshooting
y
31
SPECIFICATIONS
y
y
32
34
Specifications
Dimension
y
y
s
introduction
FEATURES
y Excellent Sensitivity
The built-in high sensitivity COLOR CCD produces a clear image.
- 0.15Lux(50IRE, @F1.2), 0.0003LUX (SENS-UP, x512)
y SSNR3 (Samsung Super Noise Reduction) Function
The high-performance W-V DSP chip effectively removes low-light gain noise
and afterimage to provide clear images even in dark environments.
y Electrical Day & Night
This camera has a function that automatically selects the mode that is
appropriate for daytime or night-time conditions.
y Motion Detection
Since the camera detects motion without any additional external sensor, you can
monitor activity more efficient.
y SSDR (Samsung Super Dynamic Range)
For images with high contrast between bright and dark areas from difficult
lighting conditions such as backlighting, this camera selectively illuminates darker
areas while retaining the same light level for brighter areas to even out the overall
brightness.
y DIS (Digital Image Stabilizer)
The DIS function compensates for any camera movement, to produce more
stable pictures.
y Communication
Coaxial communication methods are supported.
- Protocol : Pelco Coaxitron
y Miscellaneous Functions
HLC(High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM,
SHARPNESS and PRIVACY functions are provided.
y OSD
The camera control is convenient by using 18 different foreign language O.S.D.
- NTSC : English, Japanese, Spanish, French, Portuguese, Taiwanese, Korean
- PAL : English, French, German, Spanish, Italian, Chinese, Russian, Polish,
Czech, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese
English_9
● INTRODUCTION
y High Resolution
By adopting a diagonal 6mm(1/3”) 410,000 (NTSC) pixel, 470,000(PAL) pixel
SONY CCD, the camera produces clear picture quality with a horizontal
resolution of 600 TV lines in color mode.
introduction
C
WHAT’S INCLUDED
Check if the following items are included in the product package.
High Resolution Varifocal
Dome Camera
User Manual
High Resolution Varifocal
Dome Camera
SCD-2060E
SCD-2060E
User Manual
M4 Tapping Screw 3EA
Installation Video
Output Cable
10_ introduction
Quick Set-up Guide
SCD-2060E
Quick Set-up Guide
COMPONENT NAMES AND FUNCTIONS
FRONT
● INTRODUCTION
➌
➒
❶
➎
➑
➋
➍
➏
➐
❶ Pan Base : Control panning angle of camera.
➋ Rotate Base : Control rotating angle of camera.
➌ x2.4 Vari-focal Lens Module 2.5~6.0mm (F1.2)
➍ Video Output Terminal to Monitor
➎ Function Setup switch : Display the menu on the screen and move the cursor to four
directions to confirm status or after changing a selected item.
➏ Video Output Jack
➐ Power Input Terminal
➑ Dome Cover
➒ Shield Case
English_11
installation
INSTALLATION
1. Separate the dome cover by turning anti-clockwise.
2. Separate the shield case by pulling from the camera body.
Latch
* To install the dome cover on the camera
body, turn the latches in locking direction as
shown in the [Figure-1].
Locking direction
[Figure-1]
Main Body
(Camera)
Shield Case
Unlocking direction
(Anti-clockwise)
Locking direction
(Clockwise)
Dome cover
 The installation should be done by qualified
Original position of
the cable
service personnel or system installers.
 If the ceiling material is not strong enough to
hold the installation screws, the camera may
fall off. Reinforce the ceiling as needed.
 To change the position of the cable, take away
the Hole Cover and pass the cable through.
12_ installation
Hole Cover
WHEN USING THE CEILING BRACKET
Ceiling bracket
● INSTALLATION
An arrow for installing
directions
s
r
M4 tapping
screw (provided)
CAMERA
Locking
direction
Unlocking
direction
Dome cover
1. Hold the ceiling bracket (located where the arrow points to) and separate it
from the main body of the camera by rotating it anti-clockwise.
(refer to the picture in 'Notes' on page 12)
2. Place the separated ceiling bracket so that the “Front” side faces the area to be
monitored and install it with the M4 tapping screws.
3. To combine the main body with the ceiling bracket, make sure that the Pan
Base fixing screw face the opposite side of the “Front” side of the ceiling
bracket and rotate it clockwise.
4. Adjust the camera lens to face the area to be monitored and fix the main body
and the dome cover by aligning the grooves and rotating the body clockwise.
English_13
installation
Pan Base
fixation
screw
M4 tapping
screw
[Figure-2]
 If you want to install the camera with the ceiling bracket together, fix them using two M4 tapping
screws at the side of the main body (refer to the [Figure-2] on page 14)
14_ installation
A
W
73˚
174˚
176˚
Rotate Base
Tilt Base
Pan Base
1. You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.
y Pan Base moves by 176˚ to each side direction and 352˚ on the whole.
y Tilt Base covers total 73˚ angle(0˚ ~ 73˚).
y Rotate Base moves by 174° to each side direction and 348° in total.
2. Methods of adjustment
y Installing the dome on a wall
➊ After mounting the camera on a wall, adjust the panning angle so that the
camera faces the direction that is to be monitored.
➋ Adjust the tilting angle by rotating the tilt base.
➌ Loosen the rotate base hold screw and adjust rotate base for the best view.
➍ Tighten the rotate base hold screw.
y Installing the dome on a ceiling
➊ After mounting the camera on a ceiling, adjusting the panning angle to the
correct viewing position by rotating the pan base.
➋ Adjust the tilting angle by rotating the tilt base.
➌ Loosen the rotate base hold screw and adjust rotate base for the best view.
➍ Tighten the rotate base hold screw.
English_15
● INSTALLATION
ng
ADJUST THE PANNING AND TILTING WHILE
WATCHING THE MONITOR
connection
CONNECTING TO MONITOR
Connect the VIDEO-OUT jack to the VIDEO-IN jack of the monitor.
U
y
y
CCTV Camera
Monitor
y As the connecting method varies with the instruments, refer to the manual supplied with
the instrument.
y Only connect the cable when the power is turned off.
CONNECTING TO POWER
Connect the adaptor to the power input terminal as shown in the figure below. The
recommended adaptor specification for SCD-2060E is DC 12V / 500mA or AC 24V /
300mA.
---- Power Input Terminal
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size (AWG)
#24 (0.22mm2)
#22 (0.33mm2)
#20 (0.52mm2)
#18 (0.83mm2)
Resistance (Ω/m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
y As shown in the table above, voltage decreases as the wire gets longer. Therefore
use of an excessively long adaptor output line for connection to the camera may
affect the performance of the camera.
* Standard voltage for camera operation : AC 24V ± 10%, DC 12V ±10%
* There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
16_ connection
e
y
.
USING COAXIAL COMMUNICATIONS
● CONNECTION
h
 Be sure to connect power only after all the installation is complete.
 Note that DC adaptor is not supplied with camera.
y Coaxial Communications System
y OSD Control method
CAMERA
DVR
SET
MENU/ENTER
UP
UP KEY
DOWN
DOWN KEY
LEFT
LEFT KEY
RIGHT
RIGHT KEY
※ To enable the coaxial function, you should use a DVR that supports the coaxial communication.
DVR
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
5
DVD RECORDER
2
6
3
7
4
8
9
10
11
12
13
14
15
16
ZOOM
FREEZE
BACKUP
TELE
WIDE
VIEW
MODE
AUDIO
ALRAM
OPEN/CLOSE
SEARCH
PRESET
MENU
USB
RETURN
MENU
SEARCH
MULTI
REC
MENU
PRESET
CAM
1
6
MON
2
7
GROUP
PTZ
3
8
DVR
4
9
MTX
5
SETUP
ESC
: BNC
•
• ---- : RS-485
TRACK
FUNC
ENTER
CLOSE
OPEN
0
NEAR
WIDE
FAR
TELE
- Video Cable
The camera’s video output port is connected to the monitor with a BNC coaxial
cable, shown below : If the distance between the camera and the monitor exceeds
the recommended maximum, please use an auxiliary video amp.
Distance
Recommended Cable Specification
300m
3C2V(RG-59/U)
450m
5C2V(RG-6/U)
600m
7C2V(RG-11/U)
 If the camera is controlled through coaxial communication, please use a video amp intended for
coaxial communications. Regular video amps do not transfer coaxial signals.
English_17
setup
S
u
S
MENU CONFIGURATION
MAIN SETUP
LENS
● DC
EXPOSURE
● BRIGHTNESS
● SENS-UP
● SHUTTER
● RETURN
● AGC
WHITE BAL
● ATW
● MANUAL
● OUTDOOR
● AWC→SET
● INDOOR
SSDR
● OFF
● ON
BACKLIGHT
● OFF
● BLC
SSNR3
● ON
● OFF
DAY/NIGHT
● COLOR
● B/W
● AUTO
SPECIAL
● IMAGE ADJ
● SYNC
● DIS
● MONITOR
● MOTION DET
● LANGUAGE
● CAM TITLE
● PRIVACY
● RETURN
EXIT
● SAVE
● NOT SAVE
● RESET
● HLC
MENU SETUP
Use the Function Setup switch within the camera.
Function Setup switch
1. Press the Function Setup switch.
y Main setup menu is displayed on the monitor screen.
18_ setup
Select the function
using the Function
Setup switch.
Change the status
using the Function
Setup switch.
● SETUP
MAIN SETUP
䯝 1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
4.SSDR
OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
7.DAY/NIGHT
COLOR
8.SPECIAL
9.EXIT
SAVE
2. Select a desired function using the Function Setup switch.
y Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
 An item with the
icon also has sub menus. To select a sub menu, select an item with the icon
and press the Function Setup switch.
 An item with the - - - icon is unavailable due to function settings.
LENS
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed,
select ‘LENS’ by using the Function Setup
switch so that the arrow indicates ‘LENS’.
MAIN SETUP
䯝 1.LENS
2.EXPOSURE
DC
2. The Lens mode has a sub menu, shown below.
- BRIGHTNESS : Adjusts the video brightness.
- FOCUS ADJ : To adjust the lens focus correctly, you must activate the
Focus Settings mode. To activate the Focus Settings mode, adjust the
lens focus, and then deactivate the settings mode.
y You can adjust the shutter value of ESC shutter mode.
 If color rolling occurs, set Shutter to ---.
EXPOSURE
1. When the SETUP menu screen is displayed,
select EXPOSURE by using the Function
Setup switch so that the arrow indicates
'EXPOSURE'.
MAIN SETUP
1.LENS
䯝 2.EXPOSURE
3.WHITE BAL
DC
ATW
2. Select a desired mode using the Function
Setup switch.
English_19
setup
y BRIGHTNESS : Adjusts the video brightness.
EXPOSURE SETUP
y SHUTTER : You can select the shutter.
䯝 1.BRIGHTNESS IIIIIÂIIIIIIIIIIIIIIII 25
2.SHUTTER
--- A.FLK : Select this when you
3.AGC
HIGH
experience picture flicker, which can
4.SENS-UP
OFF
happen when there is a clash with the
5.RETURN
frequency of the installed lighting.
- ESC : Select this to control the shutter
speed automatically. If ESC is selected, the shutter speed is automatically
controlled depending on the ambient illumination of the subject.
- MANUAL : You can control shutter speed manually.
(NTSC MODEL : 1/60~1/120,000 sec, PAL MODEL : 1/50~1/120,000 sec)
- --- : Shutter speed is fixed at 1/60sec(1/50sec).
 Set the shutter mode to --- if color rolling occurs.
 When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the picture may
become unstable if the camera faces a bright fluorescent light. Therefore, take care when
choosing the installation position.
 When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
y AGC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen- but the higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 32dB.
- HIGH : Allows automatic gain control from 5.3dB to 37dB.
y SENS-UP : When it is night or dark, the
camera automatically detects the
light level and maintains a clear
picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
LIMIT
䯝 AUTO
x2
Press SET to Return
y RETURN : Select this to save the changes in the EXPOSURE menu and return to
the SETUP menu.
 If you press the Function Setup switch in ‘AUTO’ mode, You can adjust brightness by adjusting
the SENS-UP level. (x2 ~ x512)
 Note that the higher the SENS-UP level, the brighter the screen, but the more likely it is that an
after-image will appear.
 Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the
sens-up level is increased, this is normal.
 If GAIN of EXPOSURE is not in use, the SENS-UP (Sensitivity-Up) is set to “---“.
20_ setup
WHITE BAL (WHITE BALANCE)
Use the White Balance function to adjust the screen color.
y
ay
en
2. Select a desired mode using the Function
Setup switch.
MAIN SETUP
1.LENS
2.EXPOSURE
䯝 3.WHITE BAL
4.SSDR
DC
ATW
OFF
※ Select one of the following 5 modes, as appropriate for your purpose.
y ATW : Select this when the color temperature is between 1,700°K and 11,000°K.
y OUTDOOR : Select this when the color temperature is between 1,700°K and
11,000°K.(sodium light inclusion)
Select this when the color temperature of environment surrounding
the subject is out of the control range (e.g. clear sky, or sunset).
y INDOOR : Select this when the color temperature is between 4,500°K and 8,500°K.
y MANUAL : Select this to fine-tune White
Balance manually. Set White
Balance first by using the ATW
or AWC mode. After that switch
to MANUAL mode, fine-tune the
White Balance and then press
the Function Setup switch.
WB MANUAL
䯝 RGAIN
BGAIN
IIIIIIIIIIIIIIIIÂIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIÂIIIIIIIIIIIIII
529
532
Press SET to Return
y AWC→SET : To find the optimal luminance level for the current environment,
point the camera towards a sheet of white paper and press the
Function Setup switch. If the environment changes, readjust it.
 White Balance may not work properly under the following conditions.
o
➊ When the ambient illumination of the subject is dim.
g
➋ If the camera is directed towards a fluorescent light or is installed in a
place where illumination changes dramatically, the White Balance
operation may become unstable.
n
English_21
● SETUP
1. When the SETUP menu screen is displayed,
select ‘White Bal’ by using the Function
Setup switch so that the arrow indicates
‘White Bal’.
setup
SSDR (SAMSUNG SUPER DYNAMIC RANGE)
SSDR illuminates darker areas of an image while retaining the same light level for
brighter areas to even out the overall brightness of images with high contrast between
bright and dark areas.
1. When the SETUP menu screen is displayed,
select ‘SSDR’ by using the Function Setup
switch so that the arrow indicates ‘SSDR’.
2. Use the Function Setup switch to change
the SSDR level in the sub menu according to
the contrast between bright and dark areas.
SSDR ON
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
䯝 4.SSDR
5.BACKLIGHT
DC
ATW
OFF
OFF
SSDR OFF
BACKLIGHT
The SCD-2060E is designed so that it delivers a
distinctive subject and background at the same
time, even when the subject is in backlight, by
adopting a function of the proprietary W-V DSP
chip.
1. When the SETUP menu screen is displayed,
select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates
BACKLIGHT .
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
䯝 5.BACKLIGHT
6.SSNR3
DC
ATW
OFF
OFF
ON
2. Select a desired mode using the Function Setup switch depending on the camera
purpose.
22_ setup
or
n
y BLC : Enables a user to directly select a
desired area from a picture and to
view the area more clearly.
- LEVEL : Adjusts the brightness level of a
monitoring area.
y HLC (High Light Compensation) :
This function masks any areas of peak white
light, this minimizes whiteout due to over
exposure and thus preserve much of the onscreen details that are within the camera view.
- LEVEL : Adjusts the brightness level of a
monitoring area.
- LIMIT : Enable to change the operating
condition.
- MASK COLOR/TONE :
Change the color / brightness of the masking
area. (Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT :
Adjust the area to be enhanced.
MIDDLE
38
109
IIIIIIÂIIIIIIIIIIIIIII
54
IIIIIIIIIIIIIIIIÂIIIII 121
IIIIIÂIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIÂIII
Press SET to Return
HLC SETUP
䯝 LEVEL
MIDDLE
NIGHT ONLY
LIMIT
MASK COLOR
BLACK
MASK TONE ÂIIIIIIIIIIIIIIIIIIIII
1
ÂIIIIIIIIIIIIIIIIIIIII
TOP
5
IIIIIIIIIIIIIIIIIIIIIÂ
120
BOTTOM
ÂIIIIIIIIIIIIIIIIIIIII
5
LEFT
IIIIIIIIIIIIIIIIIIIIÂI 172
RIGHT
Press SET to Return
y OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the switch.
 Because there can be a difference in the effectiveness of HLC according to the amount of light
area in the screen, optimize the installation angle for the best HLC performance.
 When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT ONLY
mode.)
 The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY
mode.)
 When HLC function is used, D-ZOOM and DIS functions are not activated.
English_23
● SETUP
- TOP/BOTTOM/LEFT/RIGHT :
Adjust the area to be enhanced.
BLC SETUP
䯝 LEVEL
TOP
BOTTOM
LEFT
RIGHT
setup
SSNR3
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed,
select 'SSNR3' by using the Function Setup
switch so that the arrow indicates 'SSNR3' .
2. Select a desired mode using the Function
Setup switch.
y OFF : Deactivates SSNR3. Noise is not
reduced.
y ON : Activates SSNR3 so that noise is
reduced.
3. Set the SSNR3 mode to 'ON' and press the
Function Setup switch. Then you can adjust
the noise reduction level.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
4.SSDR
OFF
5.BACKLIGHT
OFF
䯝 6.SSNR3
ON
7.DAY/NIGHT
COLOR
SSNR3
䯝 LEVEL
IIIIÂIIIIIIIIIIIIIIIII
10
Press SET to Return
 You cannot set the SSNR3 to 'ON' or 'OFF' when the AGC mode of the EXPOSURE menu is 'OFF'.
 When adjusting the noise reduction level of the SSNR3 mode, remember that the higher the level
set, the more the noise level will be reduced but that after image may also occur.
DAY/NIGHT
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed,
select ‘DAY/NIGHT’ by using the Up and
Down buttons so that the arrow indicates
‘DAY/NIGHT’.
2. Select a desired mode using the Left and
Right buttons according to the picture
display you want.
24_ setup
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
4.SSDR
OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
䯝 7.DAY/NIGHT
COLOR
8.SPECIAL
y COLOR : The picture is always displayed in color.
y B/W : The picture is always displayed in black and white.
You can turn on or off the burst signal on B/W mode.
AUTO SETUP
▶ DWELL TIME
BURST MODE
5 SEC
ON
Press SET to Return
- DWELL TIME :
You can select the duration time about changing the day/night mode.
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
 When AGC in the EXPOSURE menu is ‘OFF’, AUTO mode is not available to select.
el
English_25
● SETUP
y AUTO : The mode is switched to ’Color
‘ in a normal environment, but
switches to ’B/W‘ mode when
ambient illumination is low. To set
up the switching time for AUTO
mode, press the Function Setup
switch. You can turn on or off the
burst signal on B/W mode.
setup
SPECIAL
1. When the SETUP menu screen is displayed,
select ‘SPECIAL’ by using the Function
Setup switch so that the arrow indicates
‘SPECIAL’.
2. Select a desired mode using the Function
Setup switch.
y IMAGE ADJ :
1) When the SPECIAL menu screen is
displayed, select ‘IMAGE ADJ’ by using
the Function Setup switch so that the
arrow indicates ’IMAGE ADJ‘.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
4.SSDR
OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
7.DAY/NIGHT
COLOR
䯝 8.SPECIAL
9.EXIT
SAVE
SPECIAL
#䯝 1.IMAGE ADJ
2.MONITOR
3.CAM TITLE
4.SYNC
5.MOTION DET
6.PRIVACY
7.DIS
8.LANGUAGE
9.RETURN
IMAGE SETUP
䯝 1.V-REV
2.H-REV
3.D-ZOOM
4.FONT COLOR
5.SHARPNESS
6.RETURN
LCD
OFF
INT
OFF
OFF
OFF
ENGLISH
OFF
OFF
OFF
WHITE
ON
2) Select a desired mode using the Function
Setup switch.
- V-REV : You can flip the picture vertically on the screen.
- H-REV : You can flip the picture horizontally on the screen.
- D-ZOOM : You can use a digital zoom of x1 ~ x16.
- FONT COLOR : You can change the OSD font color.
(White, Yellow, Green, Red, Blue)
- SHARPNESS : As you increase this value, the picture outline becomes stronger and
clearer. Adjust this value appropriately depending on the sharpness
of the picture.
- RETURN
26_ setup
: Select this to save the settings for the IMAGE ADJ menu and to
return to the SPECIAL menu.
may appear.
y Monitor : Please change the settings value of video appropriate to your monitor.
- LCD : Please select this menu item when
using an LCD monitor.
You can change the gamma, PED
level and color gain in the sub menus.
- CRT : Please select this menu item when
using a CRT monitor.
LCD MONITOR
▶ GAMMA
0.55
IIIIIÂIIIIIIIIIIIIIIII 17
PED LEVEL
IIIIIIIIIIIIIIIÂIIIIII
COLOR GAIN
50
RESET
Press SET to Return
- USER : Please use this menu item when
using a monitor other than standard ones. You can change the gamma,
PED level and color gain in the sub menus.
y CAM TITLE :
If you enter a title, the title will appear on the monitor.
➊ If the SPECIAL menu screen is
displayed, use the Function Setup
switch so that the arrow indicates
‘CAM TITLE’.
➋ Set it to ‘ON’ by using the Function
Setup switch.
➌ Press the Function Setup switch.
➍ Use the Function Setup switch to
move to a desired letter and select the
letter by pressing the switch. Repeat
this to enter multiple letters. You can
enter up to 15 letters.
➎ Enter a title, move the cursor to ’POS’
and press the Function Setup switch. The
entered title appears on the screen. Select
the position to display the title on the screen
by using the Function Setup switch and
press. When the position is determined,
select ’END’ and press the Function Setup
switch to return to the SPECIAL menu.
CAMERA TITLE SETUP
A B C
N O P
a b c
n o p
- . 0
←→
D E
Q R
d e
q r
1 2
CL
F G H I J K L M
S T U V W X Y Z
f g h i j k l m
s t u v w x y z
3 4 5 6 7 8 9
R POS END
_______________
FRONT DOOR
English_27
● SETUP
d
 When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
 If you increase the SHARPNESS level too high, the picture may become distorted or noise
setup
 When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you
enter one.
 English and Numbers are available in the mode.
 If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted.
To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch.
Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then
press the Function Setup switch.
y SYNC : In areas where the supply is at
SYNC
60Hz(NTSC), 50Hz(PAL), you can
ÂIIIIIIIIIIIIIIIIIIIII
▶ PHASE
0
synchronize the output phase of
multiple cameras using the power
Press SET to Return
synchronization function (Line-Lock)
without using a synchronization signal generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select ‘phase’.
 When using AC power at 60Hz(NTSC), 50Hz(PAL) frequency, you can use the L/L type
synchronization.
 When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
y MOTION DET :
This product has a feature that allows
you to observe movement of objects in
8 different areas on the screen, and the
words 'MOTION DETECTED' appear on
the screen when movement is detected.
You can monitor activity more efficient.
MOTION DET
䯝 1.SENSITIVITY
AREA1
2.AREA MODE
ON
3.SEL POS
L-TOP
ÂIIIIIIIIIIIIIIIIIIIII
3
4.XPOS
IIIÂIIIIIIIIIIIIIIIIII 4
5.YPOS
6.FILL → SET
7.RETURN
➊ When the SPECIAL menu screen
is displayed, press the Function Setup switch so that the arrow indicates
'MOTION DET'.
➋ Set up the mode using the Function Setup switch.
- SENSITIVITY :
You can select up to 8 MD areas. When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small movement.
28_ setup
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be
used.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
.
n
- FILL → SET : Fills in a selected MD area. The color of filling is sequentially
selected as brown, orange, blue, cyan, yellowish green, yellow,
magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return
to the SPECIAL menu.
y PRIVACY : Mask an area you want to hide on the screen,
➊ When the SPECIAL menu screen is
displayed, press the Function Setup switch
so that the arrow indicates ‘PRIVACY’.
PRIVACY AREA SETUP
䯝 1.AREA
AREA1
2.MODE
OFF
3.MASK COLOR
GREEN
1
4.MASK TONE ÂIIIIIIIIIIIIIIIIIIIII
IIÂIIIIIIIIIIIIIIIIIII
5.TOP
39
IIIIIÂIIIIIIIIIIIIIIII
79
6.BOTTOM
ÂIIIIIIIIIIIIIIIIIIIII
13
7.LEFT
IIIÂIIIIIIIIIIIIIIIIII
8.RIGHT
52
9.RETURN
➋ Set up the mode using the Function
Setup switch.
- AREA : You can select up to 12
PRIVACY areas.
- MODE : Determines whether to use
the area selected.
- MASK COLOR :
Determine area color. You can select
GREEN, RED, BLUE, BLACK, WHITE and GRAY.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to
the SPECIAL menu.
y DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.




As the DIS function uses the digital zoom the camera's resolution will decrease.
DIS doesn’t operate when background illumination is too low.
DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
If DIS is enabled, the digital zoom is not configured to less than X1.2 level.
English_29
● SETUP
ou
setup
y LANGUAGE : You can select the menu language according to your requirements.
y RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
EXIT
Select a desired EXIT mode using the Function Setup switch depending on the camera
purpose.
y SAVE : Save the current settings and exit the MAIN SETUP menu.
y NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
y RESET: Resets the camera settings to the factory defaults.
Language and Monitor settings are not initialized.
30_ setup
t
T
If
n
s.
troubleshooting
TROUBLESHOOTING
N
If you have trouble operating your camera, refer to the following table. If the guidelines do
not enable you to solve the problem, contact an authorized technician.
SOLUTION
Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera
and monitor are fixed properly.
▶ Check that you have properly connected VIDEO cable to the camera
VIDEO output jack.
The image on the screen is dim.
▶ Is the lens stained with dirt? Clean your lens with a soft, clean cloth.
▶ Check the monitor and DVR settings.
▶ If the camera is exposed to very strong light, change the camera position.
The image on the screen is dark.
▶ Adjust the contrast feature of the monitor or DVR.
▶ If you have an intermediate device, set the 75Ω / Hi-z properly.
The camera is not working
properly, and the surface of the
camera is hot.
▶ Check that you have properly connected the camera to an appropriate
power source.
The SENS-UP function does not
work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or
‘MANUAL’.
The Motion Detection function does
not work.
▶ Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.
Color is not correct.
▶ Check the setting of WHITE BAL SETUP menu .
The screen flickers continually.
▶ Check that the camera is not pointing at the sun.
When coaxial communication is
not available
▶ Make sure that the camera and monitor are installed within the
recommended distance.
▶ Use the video amplifier equivalent to coaxitron if the
recommended installation distance is exceeded.
English_31
● TROUBLESHOOTING
PROBLEM
specifications
SPECIFICATIONS
SCD-2060EN
SCD-2060EP
Imaging Device
B
C
Video
D
1/3” Super HAD CCD II
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
D
Effective Pixels
768(H) x 494(V)
752(H) x 582(V)
M
Scanning System
2 : 1 Interlace
Synchronization
Internal / Line Lock
Frequency
H : 15.734KHz / V : 59.94Hz
Horizontal Resolution
600 TV lines
Min. Illumination
0.15Lux (50IRE@F1.2), 0.0003Lux (Sens-up, x512)
S / N Ratio
52dB (AGC off, Weight on)
Video Output
CVBS : 1.0Vp-p, 75Ω composite
P
S
I
H : 15.625KHz / V : 50Hz
Lens Type
G
W
E
D
R
C
Focal Length (Zoom Ratio)
2.5 ~ 6mm (2.4x)
Max. Aperture Ratio
1:1.2(Wide) ~ 2.8(Tele)
Angular Field of View
H: 103.4˚(Wide) ~ 46.6˚(Tele) / V: 77.6˚(Wide) ~ 35.1˚(Tele)
Lens Type
DC Auto Iris
O
H
Mount Type
Board Type
E
Pan / Tilt
P
E
I
Pan Range
0°~352°
P
Tilt Range
0°~73°
M
Rotate Range
0°~348°
C
Operational
ON Screen Display
D
Multi-language Support by Coaxial Cable Multi-language Support by Coaxial Cable
English, Japanese, Spanish, French, English, French, German, Spanish, Italian,
Portuguese, Taiwanese, Korean
Chinese, Russian, Polish, Czech, Romanian,
Serbian, Swedish, Danish, Turkish, Portuguese
Camera Title
Off / On (Displayed 15 characters)
Day & Night
Auto (Electrical) / Color / B/W
32_ specifications
W
※
SCD-2060EN
SCD-2060EP
Backlight Compensation BLC / HLC / OFF
SSDR (Off / On)
Digital Noise Reduction
SSNRIII ( Off/On )
Digital Image Stabilization
Off / On
● SPECIFICATIONS
TROUBLESHOOTING
Contrast Enhancement
Motion Detection
Off / On (8 programmable zones)
Privacy Masking
Off / On (12 programmable zones)
Sens-up (Frame
Integration)
2x ~ 512x
Gain Control
Off / Low / High
White Balance
ATW / Outdoor / Indoor / Manual / AWC (1,700K° ~ 11,000K°)
Electronic Shutter Speed 1/60 ~ 1/120,000 sec
Digital Zoom
Off / On (1x ~ 16x)
Reverse
H-Rev ( Off/On ), V-Rev ( Off/On )
1/50 ~ 1/120,000 sec
Communication
Coaxial Control ( SPC-300 Compatible )
Protocol
Coaxial : Pelco-C (Coaxitron)
Environmental
Operating Temperature /
-10°C ~ +50°C (+14°F ~ +122°F) / Less than 90% RH
Humidity
Electrical
Input Voltage
Dual ( 24VAC±10% & 12VDC±10% )
Power Consumption
Max. 3.5W
Mechanical
Color / Material
Ivory / Plastic ( Dome Cover : Clear )
Dimension (Ø x H)
Ø115.8x92.7mm (Ø4.56 x 3.65 ˝ )
Weight
350g
※ This specification can be changed without notice for performance improvement of product.
English_33
specifications
DIMENSION
2-120˚
Ø74.1 (2.92˝ )
100 (3.94˝ )
92.7 (3.65˝ )
115.8 (4.56˝ )
97.0 (3.82˝ )
34_ specifications
Unit : mm (Inches)
)
MEMO
MEMO
MEMO
MEMO
MEMO
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222, FAX : +1-310-632-2195
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300, FAX : +44-1932-45-5325
P/NO. : Z6806159901A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising