Regency Fireplace Products | E33-NG10 | Installation manual | Regency Fireplace Products E33-NG10 Installation manual

Regency Fireplace Products E33-NG10 Installation manual
E33 Gas Insert
MODELS:
E33-NG1 Natural Gas
E33-LP1 Propane
Owners & Installation Manual
WARNING:
Improper installation, adjustment, alteration, service or
maintenance can cause injury, property damage, or loss
of life. Refer to this manual. For assistance or additional
information consult an authorized installer, service agency
or the gas supplier.
FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapours and
liquids in the vicinity of this or any other appliance.
FOR YOUR SAFETY:
What to do if you smell gas:
 Do not try to light any appliance
 Do not touch any electrical switch:
do not use any phone in your
building.
 Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
 If you cannot reach your gas
Installation and service must be performed by an authorized
supplier, call the fire department.
installer, service agency or the gas supplier.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
918-513c
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4
04/12/11
FPI GAS FIREPLACE INSERT
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Gas Insert by FPI.
The E33 Gas Insert has been designed to provide you with all the warmth and charm of a fireplace,
at the flick of a switch. The E33-NG1 and E33-LP1 have been approved by Warnock Hersey for
both safety and efficiency. As it also bears our own mark, it promises to provide you with economy,
comfort and security for many trouble free years to follow. Please take a moment now to acquaint
yourself with these instructions and the many features of your FPI Fireplace.
2
E33 FPI Direct Vent Gas Insert
DIMENSIONS
32-1/4"(819mm)
16-1/2"(419mm)
24-1/2"(622mm)
23-13/16"(605mm)
18"(203mm)
31-1/8"(790mm)
25"(635mm)
1-3/8"
(35mm)
11-1/4"
(286mm)
23"(583mm)
45-9/16"(1157mm)
16-1/2"(419mm)
10-11/16”
(271mm)
46-15/32” (1180)
28.11/16” (729mm)
26-3/4” (678mm)
33-5/16” (846mm)
18-7/16” (467mm)
42-7/16” (1078mm)
Low Profile Faceplate Dimensions
E33 FPI Direct Vent Gas Insert
3
TABLE OF CONTENTS
DIMENSIONS
Unit Dimensions ............................................................3
Excalibur Screen Doors ...............................................27
Excalibur Accent Kit ....................................................27
Wiring Diagrams ..........................................................28
Optional Remote Control ............................................29
Optional Wall Thermostat ...........................................29
SAFETY LABEL
OPERATING INSTRUCTIONS
Copy of Safety Decal .....................................................5
REQUIREMENTS
MA Code - CO Detector.................................................6
INSTALLATION
Important Message ......................................................7
For Your Safety ..............................................................7
Before You Start ............................................................7
Gas Pressure Testing Specifications .............................8
Installation Into A Solid Fuel Burning Fireplace Or
Factory Built Fireplace ...................................................8
Installation Checklist ......................................................8
Materials Required ........................................................9
Venting...........................................................................9
Flue Liner Installation ....................................................9
Gas Insert Aeration System ...........................................9
Minimum Fireplace Opening..........................................9
Minimum Fireplace Opening Excalibur® Option.............9
Combustible Mantel Clearances................................10
Minimum Clearances To Combustibles .......................10
Gas Connection .......................................................... 11
Gas Pipe Pressure Testing ..........................................12
SIT Valve Description ..................................................12
Optional Brick Panel ....................................................12
Log Set Installation ......................................................14
Conversion from NG to LP ..........................................17
Faceplate & Trim ........................................................20
Contemporary Faceplate & Door Frame .....................21
Low profile Faceplate installation ................................23
Standard Flush Door ...................................................25
Flush Louvers ..............................................................25
Full Screen doors ........................................................25
Excalibur® Surround ...................................................26
4
First Fire ......................................................................30
Operating Instructions .................................................30
Lighting Procedure ......................................................30
Shutdown Procedure ...................................................30
Final Check..................................................................30
Copy Of Lighting Instruction Plate ..............................31
Automatic Convection Fan Operation..........................31
Normal Operating Sounds Of Gas Appliances ............31
MAINTENANCE
Maintenance Instructions.............................................32
General Vent Maintenance ..........................................32
Log Replacement ........................................................32
Glass Gasket ...............................................................32
Steel Or Gold Trim .......................................................32
Door Glass ..................................................................33
Fan Maintenance .........................................................33
Valve Assembly Removal And Installation ...................34
PARTS LIST
Main Assembly ............................................................35
Burner & Log Assembly ...............................................36
Full Screen Front .........................................................37
Faceplates, Trims And Hearths ...................................38
Contemporary Faceplate & Door Frame .....................39
Low profile faceplate ...................................................40
WARRANTY
Warranty .....................................................................43
E33 FPI Direct Vent Gas Insert
SAFETY LABEL
This is a copy of the labels that accompany
each E33 Gas Insert. We have printed a
copy of the contents here for your review.
The safety label is located on a plate inside
the base of the unit visible when the bottom
louver is opened. Ensure that the safety label
is attached to the unit.
NOTE: FPI units are constantly being
improved. Check the label on the unit and
if there is a difference, the label on the unit
is the correct one.
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appliances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.
E33 FPI Direct Vent Gas Insert
5
REQUIREMENTS
MA Code - CO Detector
(for the State of Massachusetts only)
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.
6
E33 FPI Direct Vent Gas Insert
INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The FPI Gas Insert must be installed in accordance
with these instructions. Carefully read all the
instructions in this manual first. Consult the building
authority having jurisdiction to determine the need
for a permit prior to starting the installation.
NOTE: Failure to follow the instructions could cause
a malfunction of the heater which could result in
death, serious bodily injury, and/or property damage.
Failure to follow these instructions may also void
your fire insurance and/or warranty.
FOR YOUR SAFETY
This appliance requires air for proper combustion.
Always provide adequate combustion and
ventilation air. Follow instructions and information
in CAN/CGA B149 (in Canada) or the National Fuel
Gas Code ANSI Z223.1 (in the USA), regarding
requirements for combustion and ventilation air.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVETHAT
CONTROL COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
E33 FPI Direct Vent Gas Insert
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUAL
IN THE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI Standards to make you aware of the following:
General Safety Information
4) See general construction and assembly
instructions. This appliance may only be
installed in a vented, noncombustible fireplace.
5) This appliance is Listed for bedroom installations
when used with a Listed Millivolt Thermostat.
Some areas may have further requirements,
check local codes before installation.
6) Always connect this insert to a vent system
venting to the outside of the building envelope.
Never vent to another room or inside a building.
Make sure that the vent is properly sized and is
of adequate height to provide the proper draft.
7) Inspect the venting system annually for
blockage and any signs of deterioration.
8) Any glass removed for servicing must be
replaced prior to operating the appliance.
9) To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
10) Due to high temperatures, the appliance should
be located out of high traffic areas and away
from furniture and draperies. Children and
adults should be alerted to the hazards of high
surface temperatures, especially the fireplace
glass and gold trims, and should stay away to
avoid burns or clothing ignition. Young children
should be carefully supervised when they are
in the same room as the appliance. Clothing or
other flammable material should not be placed
on or near the appliance.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
1) The appliance installation must conform with
local codes or in the absence of local codes,
with CAN/CGA B149 (in Canada) or the National
Fuel Gas Code ANSI Z223.1 in the U.S.A. This
appliance should be installed by a qualified gas
fitter technician only.
2) Installation and repair should be done by a
qualified service person.
3) The appliance should be inspected before use
and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, animal hair, etc. It is imperative that
control compartments, burners and circulating
air passageways of the appliance be kept clean.
7
INSTALLATION
GAS PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut off valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than
1/2 psig. (3.45 kPa).
SPECIFICATIONS
At pressures over 1/2 psig, the pipe to the unit
must be disconnected.
Gas Input Capacity:
Natural Gas 38,000 Btu/h
Propane
35,500 Btu/h
Min. Input:
Natural Gas 20,000 Btu/h
Propane
19,000 Btu/h
Fuels: Approved for use with both natural gas,
and propane. Approved as is for use at 0' to
4,500' (0-1370m).
Electrical:
120V A.C. system.
Circulation Fan: Variable speed, 127 CFM.
Log Set:
Ceramic fibre, 8 per set.
Vent System:
3" co-linear aluminum flex.
INSTALLATION INTO A
SOLID FUEL BURNING
FIREPLACE OR
FACTORY BUILT
FIREPLACE
The E33 Gas Inserts have been tested and
approved to be vented into any masonry
fireplace or approved solid fuel burning
factory built fireplace that will allow the insert
to physically fit into the firebox. Refer to the
"Minimum Fireplace Dimensions" section.
If the factory built fireplace* height is too low
for your Insert, you may remove the smoke
baffle plate and damper from the factory
built fireplace as long as these items are
saved and are reinstalled in the event that
the Insert is removed. NOTE: Any alterations
made to the listed solid fuel burning factory
built fireplace may void the listing of the
fireplace. Cutting any sheet-metal parts of
the fireplace, in which the gas fireplace insert
is to be installed, is prohibited.
If the factory-built fireplace has no gas
access hole(s) provided, an access hole of
1.5" (37.5mm) or less may be drilled through
the lower sides or bottom of the firebox in
8
a proper workmanship like manner. This access
hole must be plugged with non-combustible
insulation after the gas supply line has been
installed.
The fireplace and fireplace chimney must be
clean and in good working order and constructed
of non-combustible materials and chimney
cleanouts must fit properly. Refractory, glass
doors, screen rails, screen mesh, and log
grates can be removed from the fireplace before
installing the gas fireplace insert. Smoke shelves,
shields and baffles may be removed if attached
by mechanical fasteners. A tight connection
between the gas fireplace insert flue collar and
the fireplace chimney must be made.
*Check with your local inspector before commencing
with this installation.
INSTALLATION
CHECKLIST
Before installing vent system ensure that the damper
plate is open and secure to prevent the damper plate
from falling down and crushing the liner.
The FPI Gas Insert is installed as listed
below.
the "Flue Liner Installation" section.
6) Slide the unit fully into the fireplace.
7) Test gas pressure, refer to the "Gas Pipe
Pressure Testing" section. Check aeration
system, refer to "Gas Insert Aeration Systems"
section.
8) Install standard and optional features. Refer
to the following sections where applicable:
a. Brick Panels
b. Log Installation
c. Faceplate & Trim
d. Standard Flush Door
e. Flush Louvers
f. Full Screen Doors
g. Excalibur Surround
h. Excalibur Screen Doors
i. Excalibur Accent Kit
j. Remote Control
k. Wall Thermostat
9) Final check. Refer to the "Final Check"
section. Before leaving this unit with the
customer, the installer must ensure that the
appliance is firing correctly. This includes:
a)
Clocking the appliance to ensure the
correct firing rate.
b)
Adjusting the primary air, if required, to
ensure that the flame does not carbon.
Refer to the "Gas Insert Aeration
System" section.
c)
Ensuring that the appliance is venting
correctly.
1) Check all clearances to combustibles. Refer to
the following sections where applicable:
a. Minimum Clearances to Combustibles.
b. Regency Flush Combustible Mantel
Clearances
c. Excalibur Surround & Full Screen Doors
Combustible Mantel Clearances
d. Mantel Clearances
2) Make the gas connection. Refer to the "Gas
Connection" section.
3) Install the 3" flue liner to the sliding connector
plate. Refer to the "Flue Liner Installation" section.
4) Slide the unit half way into the fireplace.
5) Pull the vent connector plate through the tapered
brackets and fasten to the front plate. Refer to
Installer must mechanically attach the supplied
label to the inside of the firebox of the fireplace
into which the gas fireplace insert is installed.
"WARNING: This fireplace has been
converted for use with a gas fireplace insert
only and cannot be used for burning wood or
solid fuels unless all original parts have been
replaced, and the fireplace re-approved by
the authority having jurisdiction."
E33 FPI Direct Vent Gas Insert
INSTALLATION
MATERIALS
REQUIRED
No electrical power supply is required for the gas
control to operate. A 120 Volt AC power cord is
hooked up to the fan. Plug the 3 wire cord into
a suitable receptacle. Do not cut the ground
terminal off under any circumstances. When
connected with 120 volts, the appliance must be
electrically grounded in accordance with local
codes, current version of the Canadian Electrical
Code CSA C22.1 (in Canada) or in the absence
of local codes, with the National Electrical Code
ANSI/NFPA 70.
NOTE: This unit is equipped with a heat
sensor thermodisc which will prevent the
blower from operating until the unit reaches
the correct temperature.
VENTING
This appliance is designed to be attached to two
3" (76mm) co-linear aluminium flex running the full
length of the chimney. The flue length must be a
minimum length of 8 ' (2.44m) and a maximum
of 35' (10.7m). See chart above for minimum
distances from roof. Periodically check that the
vent is unrestricted.
Masonry chimneys may take various contours
which the flexible liner will accommodate. However,
keep the flexible liner as straight as possible,
avoid unnecessary bending.
Part #
948-305
946-529
Description
3" Flex - 35 ft.
FPI Co-linear DV Vertical
Termination Cap
Alternate Approved Caps
46dva-VC Vertical Termination Cap
46dva-VCH High Wind Cap
46dva-GK 3" Co-linear Adaptor with flashing
FLUE LINER
INSTALLATION
1) Cut the flex liner as required.
MINIMUM FIREPLACE
OPENING
The minimum fireplace opening for the FPI gas
fireplace insert is shown in the following diagrams:
2) Mark the end of one liner with an "E" to
indicate Exhaust.
3) Connect the other end of the above liner to the
exhaust side of the termination adaptor, seal
connection with high temperature silicone.
Secure with gear clamp.
4) Connect the 2nd liner to the inlet side of the
adaptor, seal connection with high temperature
silicone. Secure with gear clamp.
GAS INSERT
AERATION SYSTEM
The air shutter can be adjusted by moving the
adjusting wire up or down. The wire is accessed
through the bottom louver opening. Open the air
shutter for a blue flame or close for a yellower
flame. The burner aeration is factory set but may
need adjusting due to either the local gas supply
or altitude.
Minimum Air Shutter Opening:
5/16"
Natural Gas
7/16"
Propane
CAUTION: Carbon will be produced if air
shutter is closed too much.
Note: Any damage due to carboning resulting
from improperly setting the aeration
controls is NOT covered under warranty.
Note: Aeration Adjustment should only be
performed by an authorized FPI Installer
at the time of installation or service.
7-1/8”
(200mm)
Low profile
MINIMUM FIREPLACE
OPENING EXCALIBUR®
OPTION
The minimum fireplace opening for the FPI gas
fireplace insert is shown in the following diagrams:
NOTE: If you are installing the Excalibur®, the
minimum fireplace dimensions are as follows:
Width (at front):
Depth:
Height:
34-1/2" (876mm)
17-3/4" (451mm)
26"
(660mm)
In areas of consistently high winds, we recommend
using the Simpson Dura-Vent System (46dva-GK
adapter and 46dva-VCH high-wind cap).
The Air Intake pipe must be attached to the inlet
air collar of the termination cap.
WARNING:
Electrical Grounding
Instructions
This appliance is equipped with
a three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
E33 FPI Direct Vent Gas Insert
9
INSTALLATION
MINIMUM CLEARANCES TO COMBUSTIBLES
Side Walls
From Unit
* A 8" (203 mm)
Ceiling
B 47" (1194 mm)
Min. Mantel Height
Max. Mantel Depth
C 15" (381 mm)
D 12" (305 mm)
Alcove Width
Alcove Depth
E
F
Hearth Height
Hearth Width
Hearth Depth
G 1-1/4" (32 mm)
H 45-1/2" (1156 mm)
I 13" (330 mm)
76" (1930 mm)
36" (914 mm)
* Alcove side wall must have a min. of 8"
clearance on one side.
COMBUSTIBLE MANTEL CLEARANCES
Because of the extreme heat this fireplace emits, the mantel clearances are critical.
Note: A non-combustible mantel may be installed at a lower height
if the framing is made of metal studs covered with a noncombustible board.
Mantel can be installed anywhere in shaded area or higher using the
above scale.
Note: Ensure the paint that is used on the mantel and the facing
is "heat resistant" or the paint may discolour.
10
E33 FPI Direct Vent Gas Insert
INSTALLATION
GAS CONNECTION
GAS CONNECTION
WARNING:
Only persons licensed to work
with gas piping may make the
necessary gas connections to
this appliance.
1) If the appliance is to be installed into an existing
chimney system, thoroughly clean the masonry
or factory built fireplace.
2) The appliance is provided with an opening on
the left hand side of the control compartment.
A 3/8" NPT gas supply pipe must be brought
near this inlet hole.
5) Install flashing.
6) Insert both liners into chimney, passing through
the damper opening.
7) Install termination cap.
8) Connect the marked end of the liner to the
exhaust collar of the vent connector plate
marked with an "E", seal connection with high
temperature silicone. Secure with gear clamp.
9) Connect the 2nd liner to the intake collar, seal
connection with high temperature silicone.
Secure with gear clamp.
NOTE:
3) Locate the center point where the vent will pass
through the chimney above the appliance. Move
the appliance into the exact location where it is
to be installed. Ensure that the Insert is level.
10) Align vent connector plate with guides on unit.
11) Slide unit into masonry opening, while ensuring
that the slot at the rear of the connector plate
mates up with the hold down plate on the unit.
12) Secure with Screw.
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
1) Final gas connection should be made after
unit is in place to avoid damage to line when
pushing the unit into position.
2) Mill-pac may be used instead of high tempture
silicone and screws may be used instead of
gear clamps at connections of liner to inlet and
vent collars.
E33 FPI Direct Vent Gas Insert
11
INSTALLATION
GAS PIPE
PRESSURE TESTING
The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 1/2 psig. (3.45 kPa). Disconnect piping
from valve at pressures over 1/2 psig.
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.
OPTIONAL
BRICK PANEL
7) Pilot Outlet
8) Main Gas Outlet
9) Alternative TC Connection Point
Optional Brick Panel Set:
Part #
Description
Top (brick) panel
Back (brick) panel
Left (brick) panel
Right (brick)panel
340-043 Top bracket
340-094 Bottom clips
511-031 Brick clips
Qty
1
1
1
1
1
2
2
NOTE: To properly check gas pressure, both
inlet and manifold pressures should be
checked using the valve pressure ports
on the valve.
1) Make sure the valve is in the "OFF" position.
2) Loosen the "IN" and/or "OUT" pressure tap(s),
turning counterclockwise with a 1/8" wide flat
screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON"
position.
5) The pressure check should be carried out with
the unit burning and the setting should be within
the limits specified on the safety label.
6) When finished reading manometer, turn off the
gas valve, disconnect the hose and tighten the
screw (clockwise) with a 1/8" flat screwdriver.
Note: Screw should be snug, but do not
over tighten.
SIT VALVE DESCRIPTION
1)
2)
3)
4)
5)
6)
Gas on/off knob
Manual high/low adjustment
Pilot Adjustment
Thermocouple Connection - option
Manifold (Outlet) Pressure Tap
Inlet Pressure Tap
2
1
IN
6
12
3
4
OUT
5
E33 FPI Direct Vent Gas Insert
INSTALLATION
Installation of Brick Panels:
1) Remove top louver and glass door if installed.
2) Remove the logs if they are already installed.
Note: the grate must be removed in order to
remove the bottom log. Ensure you slide the
bottom coal off to the right-hand side to avoid
chipping.
6) Slide the top panel and bracket assembly
carefully onto the baffle plate ensuring the
panel is centered. Make sure the tabs of the
top bracket fit into the baffle openings (refer to
Diagram 3).
9) Insert the side panel by positioning it flat
against the side walls. Tilt the panel
towards the middle of the firebox, then insert
the bottom front corner. Repeat on the other
side.
10) Install the 2 brick retaining clips, one on
each side.
3) Unwrap the brick pattern panels from the
protective wrapping. Handle the panels with
care as they can break easily.
4) Remove the two screws from the bottom of the
baffle plate. Install the bottom clips onto the
baffle plate (refer to Diagram 1).
Diagram 3
7) Insert the back panel by sliding it between
the sidewalls of the firebox and the rear log
support.
Bottom Clips
8) Before installing the side brick panels,
remove the screws from the side brick clips
(refer to Diagram 4).
Diagram 1
5) Place the top bracket onto the top edge of
the top panel (refer to Diagram 2).
Completed Installation
Top Bracket
Diagram 4
Diagram 2
E33 FPI Direct Vent Gas Insert
13
INSTALLATION
LOG SET INSTALLATION
WARNING:
Dangerous operating conditions may occur if these
logs are not positioned in their correct certified locations. Read the following instructions carefully and
refer to the attached diagrams.
3) Remove the grate by removing the two Phillips
screws. Slide the grate outwards to remove it from
the unit (refer to Diagram 1).
Gas Log Kit #340-930 contains the following:
03-17
03-18
03-19
03-20
03-21
03-22
03-23
03-24
946-669
Bottom Log
Center Top Log
Front Log
Left Log
Right Log
Left top Log
Rear Log
Right Top Log
Platinum Embers (supplied in packaged manual)
4) Angle log 03-17 and slide it between the top and
bottom burner tube under the "T" section until it
touches the left grate support bracket (refer to
Diagram 2).
03-23
03-22
Diagram 1
03-24
03-18
03-17
03-20
03-19
03-21
03-17
The "03" reference numbers (i.e. 03-23) are molded
into the rear of each log.
1) Remove and carefully unwrap the logs from the
box. Please handle with care and do not force
them into position to avoid chipping.
2) Remove the top louver and glass door if already
installed.
Diagram 2
5) Re-install the grate.
6) Line up the pin holes (located at the bottom of log
03-23) to the pins of the rear log support and position them into place. (refer to Diagram 3)
03-23
Locating Pins
Diagram 3
14
E33 FPI Direct Vent Gas Insert
INSTALLATION
7) Align the bottom grooves of log 03-21 onto the
right side of the grate and gently slide the log back
until it touches the locating tab (refer to Diagram 4
& 5).
03-23
03-21
03-21
03-17
Locating
Tab
Diagram 7
9) Place log 03-22 over log 03-23 and log 03-20.
Ensure the pin hole of log 03-22 lines up with the
left pin of log 03-23 as well as the left pin of log
03-20 (refer to Diagram 8).
Diagram 4
03-23
03-22
03-23
03-20
Locating
Pins
03-20
03-21
03-17
Diagram 8
Diagram 5
8) Align and position the pin hole of log 03-20 down
into the left locating pin of log 03-21. Slide into
the groove and gently place into position until it
touches the locating tab. (see Diagram 6 & 7)
10) Place log 03-18 over log 03-23 and log 03-20.
Ensure the pin hole of log 03-18 lines up with the
middle pin of log 03-23 and the right pin of log
03-20 (refer to Diagram 9 & 10).
03-23
03-18
03-20
Locating
Pin
Locating
Tab
Diagram 6
E33 FPI Direct Vent Gas Insert
Locating
Pins
03-21
03-20
Diagram 9
15
INSTALLATION
12) Place log 03-19 over the left center of the grate.
Ensure the log set looks like Diagram 12.
03-23
03-18
03-22
03-20
03-17
Diagram 10
03-19
11) Place log 03-24 over log 03-23 and log 03-21
ensuring the pin hole of log 03-24 lines up with the
right pin of log 03-23 and the right pin of log 03-21
(refer to Diagram 11).
03-23
Diagram 12
13) Separate platinum embers and place at the front
of the burner. Avoid stacking platinum embers.
03-24
Locating
Pins
03-21
Diagram 11
16
E33 FPI Direct Vent Gas Insert
INSTALLATION
CONVERSION KIT# 731-969 FROM NG TO LP
for E33-1 using SIT 820 NOVA Gas Valve
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION !!
4) Remove front base brick.
Each Kit contains one LPG Conversion
Kit and one DC Sparker Kit.
10) Turn control knob to the “OFF” position.
11) Remove the black protection cap by hand
from the hi/low knob (Fig.1).
LPG Conversion Kit Contains:
Qty.
Part #
Description
1
904-529
5/32" Allen Key
1
904-641
Burner Orifice #50
1
918-590
Label "Converted to
LPG"
1
908-528
Red LPG Label
1
910-037
LPG Injector
(Pilot Orifice)
1
918-485
Instruction Sheet
DC Sparker Kit Contains:
Qty.
Part #
Description
1
820-475
Bracket DC Sparker
1
820-476
Bracket DC Sparker
1
904-153
Washer #8 External
Star
1
904-330
Nut 8-32 Hex
2
904-531
Bushing Split Plastic
0.500 in.
1
904-543
Screw 8-32 x 3/4
Pan Head
2
904-553
Screw #8 x 1/2
Type "B", Black Oxide
1
910-073
Spark Generator
Battery Holder
1
910-074
Spark Generator
Switch C/W Wire
1
910-078
Battery Size AA
Energizer En91
1
910-199
Clip Wire Holder
1
910-903
Wire Fan To Power
Cord, Ground 30 in.
904-781
Velcro Hook, Black
904-782
Velcro Hook, Black
5) Remove burner by unscrewing the 2
screws.
6) Pull off the pilot cap to expose the pilot
orifice.
7) Unscrew the pilot orifice with the 5/32"
allen key and replace with the LPG pilot
orifice provided in the kit, then replace
pilot cap.
8) Remove burner orifice with a 1/2" wrench,
while using a 9/16" wrench to hold onto
the elbow behind the orifice and discard
orifice.
Fig. 1
12) Insert a 5/32” or 4mm Allen wrench into
the hexagonal key-way of the screw
(Fig. 2), rotate it counter-clockwise until it
is free and extract it.
Fig.2
13) Check that the screw is clean and if
necessary remove dirt.
14) Flip the screw (Fig. 3).
Installation of LPG
Conversion Kit:
1) Shut off the gas supply.
2) Remove the louvers and glass door.
3) Remove the logs and grate (refer Log
Installation section in E33 Manual).
Ensure you slide the bottom log 03-17 off
to the right-hand side to avoid chipping.
Burner Orifice Removal
9) Reinstall new burner orifice LPG stamped
#50 and tighten.
E33 FPI Direct Vent Gas Insert
Fig.3
17
INSTALLATION
15) Using the Allen wrench as shown in Fig.4,
rotate the screw clockwise until snug, do
not overtighten.
WARNING!
Also check that the pilot and
main burner injectors are
appropriate for the gas type.
Installation of the DC Sparker:
27) Locate the Piezo Ignitor situated at the
side of valve.
Piezo
Ignitor
18) Reverse steps 5) to 3).
19) Attach the label "This unit has been converted to LPG" near or on top of the serial
# decal.
20) Replace yellow "NG" label with red "LPG"
label.
Fig.4
WARNING!
Do not over tighten the screw.
Recommended to
grip the wrench by the short side.
16) Verify that if the conversion is from NG to
LPG, the screw must be re-assembled
with the red o-ring visible (Fig. 5).
Red o-ring visible
LPG Configuration
Fig.5
17) Re-assemble the black protection cap
(Fig. 6).
WARNING!
This conversion kit shall be
installed by a qualified service
agency in accordance with the
authority having jurisdiction. If
the information in these instruction is not followed exactly, a fire,
explosion or production of carbon monoxide may result causing property damage, personal
injury or loss of life. The qualified
service agency is responsible
for the proper installation of this
kit. The installation is not proper
and complete until the operation
of the converted appliance is
checked as specified in the manufacturer's instructions supplied
with the kit.
Note: Equipped for Altitude
0 - 4500 ft. (0 - 1370m).
28) Remove the Piezo Ignitor by unscrewing
the nut at the back of the mounting
bracket.
Ignitor
Wire
Piezo
Ignitor
29) Disconnect the ignitor wire from the Piezo
Ignitor and connect it to the D.C. Sparker.
DC
Sparker
Ignitor
Wire
30) Connect the DC spark generator wires
to the SIT Valve with the screw, which is
provided in the kit.
Fig. 6
18
E33 FPI Direct Vent Gas Insert
INSTALLATION
31) Locate the ground lug at the receptical
box, left of the unit.
35) Plug the DC spark generator wires to the
DC Sparker.
39) Find a location which is not too hot and is
easy to reach for changing the
battery.
40) Tie up the loose wire with the wire clip.
32) Connect one end of the supplied green
ground wire to the lug with the nut and
washer from the kit.
36) Connect the ground wire to the DC
Sparker mounting bracket.
41) Check for gas leaks with a proper soapy
solution or leak detector.
Ground
wire from
kit
42) Check for proper spark between the
ignitor and pilot cap. Refer to "Lighting
Procedure" section of the manual for lighting sequence.
43) Check pilot flames. Correct flame pattern
has 3 strong blue flames. Adjustment can
be made by turning the slotted screw at
the top right corner of the valve. Refer to
"Maintenance Instructions" section of the
manual for correct flame patterns.
33) Install the 1/2" bushing to the heat shield.
37) Install the supplied battery into the DC Sparker
Box by opening the battery compartment.
NOTE: The battery in the DC Sparker Box
will need to be replaced annually.
Battery
Compartment
E33 FPI Direct Vent Gas Insert
45) Check operation of flame control.
46) Check for proper flame appearance and
glow on logs.
Installer Notice:
These instructions must be left
with the appliance.
34) Run the other end of the ground wire and
DC spark generator wires through the
bushing on the heat shield.
Heat Shield
44) Check inlet (12" WC min) and outlet (11"
WC) pressures. Refer to "Gas Pipe Pressure Testing" section of the manual.
38) Mount the heat shield to the DC Sparker.
Secure into place with the velcro, which is
provided in the kit.
19
INSTALLATION
FACEPLATE & TRIM
3) Using the connectors provided, join the left
side trim (with the ON/OFF switch) to the top
trim. Diagram 2. Connect the right side trim to
the top trim.
1) Lay the faceplate panels flat, face down on
something soft so they don't scratch.
2) Take the top faceplate and align the holes in
it with the holes in the side panels. Using the
screws provided, attach from the top of the panel
(the holes in the top panel are slightly larger
than the holes in the side panel to facilitate
easier installation). Refer to Diagram 1.
Hint: Don't tighten the screws down completely
at this point, continue on with steps 3 and 4 and
do a trial fit to the unit. Make any necessary
adjustments and when it fits properly then
tighten down the screws.
Diagram 3
Rear View: Trim Assembly
Diagram 2
9) Attach the trim to the faceplate by using the
plated screws (refer to Diagram 4).
4) Place the trim on the assembled faceplate
panels, aligning the wire connections from the
switches with the notch on the left side panel.
5) Connect the fan switch wires by taking the
black and red wires with the male ends (in the
grey harness) and connect them with the wire
connectors from the fan speed control.
6) Connect the ON/OFF switch wires by taking
the black and red wires with the female ends
and connect them to the ON/OFF switch.
7) Tuck the wires into the faceplate to keep them
away from the insert using the clip provided.
Attach the clip to the rear of the faceplate to
ensure that the wires do not touch the side of
the unit. Refer to Diagram 3.
Rear View: Faceplate Assembly
Diagram 1
8) The power cord should be run behind the
faceplate panel.
Diagram 4
10) Attach the faceplate panels to the insert body
using the 4 remaining black screws. Refer to
Diagram 5.
Diagram 5
11) Push the FPI logo plate into the two holes in
the bottom left corner of the faceplate.
20
E33 FPI Direct Vent Gas Insert
INSTALLATION
CONTEMPORARY FACEPLATE &
DOOR FRAME
3) Secure loose wires using wire clips along the back of the left side
of the faceplate. Ensure to run the wires away from the firebox as
much as possible.
Kit# 341-914 Contents List:
1
1
1
2
4
4
8
1
1
Complete Faceplate with Switches
Door Frame
Bottom Louver
Hinges
Hinge Screws
Hinge Spacers
Pan Head Screws
Wire Clip
Instruction Sheet
4) Align the faceplate tabs with the tab brackets on the inside top of the
firebox and slide in place.
NOTE: For easy installation do not force both tabs in at the same
time, stagger from left to right.
Tab Brackets
1) Bring the faceplate up in front of the unit and connect the red & black
ON/OFF wires from the unit to the ON/OFF switch on the back of the
left side of the faceplate.
2) Connect the grey coated female ends of the black & red fan wires
from the unit to the male ends of the fan rheostat on the left side of
the faceplate as shown.
Fan Rheostat
E33 FPI Direct Vent Gas Insert
Faceplate
Tabs
21
INSTALLATION
5) Secure the bottom of the faceplate to the firebox flange using one
screw on each side.
8) Align the left and right side hinge with the screw holes in the bottom
louver and secure in place using 3 screws per side.
NOTE: Ensure that the bottom of the faceplate leg is aligned with the
screw hole on the inner side of the firebox flange.
9) Install the door frame by hooking the top flange over top of the glass
door, push in the bottom of the door frame to secure in place.
Faceplate secured to inner side of firebox flange.
NOTE: To ensure the gap between the door frame and faceplate legs
are equal (approximately 1/2" on each side) you may need to slide
the door frame slightly to the left or right accordingly.
6) Place 2 screws through the screw holes on the hinge and place a
spacer over each screw.
7) Secure the hinge to the bottom flange of the firebox with 2 screws
from step 6. Repeat for other side.
Door Frame Flange
Glass Door
10) Close the bottom louver.
Spacer
Completed Faceplate & Door Frame Installation
Screw
22
E33 FPI Direct Vent Gas Insert
INSTALLATION
LOW PROFILE FACEPLATE INSTALLATION
1)
Attach the inner faceplate panel to the insert body using 4 screws
in the locations shown below.
4) Tuck the wires into the clip to keep them away from the insert using
the clip provided. Attach the clip to the rear of the faceplate to ensure that the wires do not touch the side of the unit. The power cord
should be run behind the inner faceplate panel.
5) Install the on /off switch - fan speed control box to the left hand
bottom leg of the inner faceplate. Controls located on the left side.
Diagram 1
Diagram 5
6)
Secure the wires to the back of the inner faceplate with a wire clip
7)
Attach the 2 bottom louver hinges to the bottom flange on the
firebox using 2 screws per hinge.
Diagram 2
2)
Connect the male end black and red fan switch wires (in the
black casing) to the wire connectors from the fan speed control.
Diagram 3
3) Connect the female ends of the ON/OFF switch - to the ON/OFF
switch in the control box.
Diagram 6
E33 FPI Direct Vent Gas Insert
23
INSTALLATION
8)
Attach the bottom louver to the 2 hinges using 3 screws per
hinge.
Diagram 7
Final Install
9)
Take the outer faceplate, line up the openings on the left and right
legs and install onto the inner faceplate panel pins.
Diagram 10
Outer faceplate
Inner faceplate
panel pins
46-15/32” (1180)
42-7/16” (1078mm)
24
28.11/16” (729mm)
26-3/4” (678mm)
33-5/16” (846mm)
18-7/16” (467mm)
Diagram 9
E33 FPI Direct Vent Gas Insert
INSTALLATION
STANDARD
FLUSH DOOR
The standard flush door comes with a black
frame. To install the frame, simply hook the top
door flange onto the top of the unit and swing
the door towards the unit, (Diagram 1 and 2).
Be careful that the glass gasket does not roll up;
there must be a gap between the gasket and
the door lip to ensure that the door sits securely
on the unit. Refer to Diagram 3.
FLUSH LOUVERS
1) The top louver is held in place by friction fit.
Refer to Diagram 1
2) Lift the unit up slightly and push down on
the corners of the Bottom Trim Bracket and
slide under unit.
Diagram 1
Diagram 1
2) Install the Spring Hinges on the left and right
side of the bottom of the Firebox using 2
screws per hinge.
Screws
Push in Corners
Bottom Trim
Bracket
3) Place the Bottom Louver near the hinge. Flip
hinge over the Bottom Louver and secure
using 3 screws.
Diagram 2
3) Completely secure faceplate to the unit by
securing 4 screws to the Left and Right Side
Trim.
Hinge
Location
Bottom Louver
FULL SCREEN DOORS
Diagram 3
Secure door by fastening with two screws located
at bottom of glass frame (refer to Diagram 1).
To remove the flush door, reverse the above
steps.
1) Hold the full screen faceplate up against
the unit in order to make the following wire
connections.
4) Install the Top Frame by hooking it onto the
two screws at the top of the full screen door.
It is held in place by magnets.
Pull the ON/OFF connector wires thru the
box and connect them to the switch.
Connect the fan switch wires with the wire
connectors from the fan speed control. Place
clips over wires and tuck into side trim.
Screw
Top Frame
E33 FPI Direct Vent Gas Insert
25
INSTALLATION
5) Install Spring Hinges to the Left and Right
Side of the bottom of the firebox using 2
screws per hinge.
EXCALIBUR® SURROUND
IMPORTANT NOTE:
When using the Surround, the unit must be set
1" further into the fireplace than the standard
faceplate installation. See the "Minimum
Fireplace Opening Excalibur Option" section.
3) Hold the Faceplate Trim up against the
unit in order to make the following wire
connections.
3a) Pull the ON/OFF connector wires from the
firebox and connect them to the switch.
3b) Connect the fan switch wires with the wire
connectors from the fan speed control. Place
clips over wires and tuck into side trim.
1) Align the left side Faceplate Trim Bracket
with the Firebox Flange and secure using
2 screws as shown in diagram 1. Repeat
for right side.
ON/OFF
switch
Fan Speed
Switch
(Rear View)
wires to
ON/OFF
switch
6) Place Bottom Frame near hinge. Flip hinge
over Bottom Frame and secure with 3 screws
each.
wires to
Fan switch
connectors
for gas
connection
Self-adhesive
wire clip
Hinge Location
Faceplate
Trim Bracket
Bottom
Frame
Firebox
Flange
Diagram 1
7) Install the Left and Right Side Screen Doors
by placing over top of the hinges on the
faceplate. Hold the door at a 45 degree
angle to avoid scratching the faceplate.
4) Secure the Faceplate by sliding the slots in
the Faceplate into the flanges on the left and
right side Faceplate Trim Brackets. Once the
Faceplate
Faceplate is in place secure using 2 screws
Trim Bracket
per side.
2) Push the Blanking Plate down on top of the
Glass Door (refer to Diagram 2).
Faceplate
Blanking Plate
Slots
8) Close screen doors.
Top of
Glass
Door
NOTE: If you are installing the Excalibur®,
the minimum fireplace dimensions are
as follows:
Hinge
Diagram 2
Width (at front):
Depth:
Height:
34-1/2" (876mm)
17-3/4" (451mm)
26"
(660mm)
Screen Door
26
E33 FPI Direct Vent Gas Insert
INSTALLATION
EXCALIBUR SCREEN
DOORS
1) Attach door bracket to sides using 4 screws.
2) Take the hoseclamps and put them over the
back of each rivet. Squeeze the hoseclamp
to secure onto rivets ensuring that the
hoseclamp is touching the back side of
the surround. The hoseclamp can now be
released.
3) Remove the handles by removing the nut
and screw. Install the new handles by
placing them in position over the holes on
the surround louver. Put the screws through
the holes and secure them by tightening
them with a nut.
Left Side
Faceplate Bracket
Trim Flange
Door Bracket
attaches with
2 screws on
each side.
5) Place the bottom hooks of the Surround into
the bottom slots of the Faceplate. Slightly
pull up the Surround and push the top hooks
into the top slots of the Faceplate. Push
down to secure. Tug on the Surround to
ensure it is securely locked in place.
Double Screen Door: attach to left and right
side of unit.
Backside of
Surround Shown
4) Place the emblem over the emblem design
on the surround. Insert the studs through the
holes. To secure them first put on the split
lock washer and then the nut and tighten.
2) Slide the door(s) onto the hinges.
Hooks
5) Remove the 2 studs on the sides of the Hood.
Insert the new studs through the holes and
secure them by first putting on the washer
and then tighten with a nut.
Faceplate Slots
EXCALIBUR
ACCENT KIT
Faceplate
Surround
E33 FPI Direct Vent Gas Insert
1) Remove the rivets from the surround by
pulling off the hoseclamp (located at the
backside of surround) with a screwdriver or
plyer. Re-install the rivets by putting them
through the holes on the sides of the surround.
DOUBLE DOOR OPTION
Remove the handles by removing the nut
and screw. Install the new handles by placing
them in position over the holes on the door(s).
Put the studs through the holes and secure
them by tightening them with a nut.
27
INSTALLATION
WIRING DIAGRAMS
This heater does not require a 120V A.C. supply
for operation. However, a 120V A.C. power
supply is needed for the fan/blower operation.
Caution: Ensure that
the wires do not touch
any hot surfaces and
are away from sharp
edges.
WARNING: Electrical Grounding Instructions
This appliance is equipped with a three pronged
(grounding) plug for your protection against shock
hazard and should be plugged directly into a properly
grounded three-prong receptacle. Do not cut or remove
the grounding prong from this plug.
For NATURAL GAS Units and Units NOT Equipped with DC Spark Boxes
CAUTION:
Label all wires prior
to disconnection when servicing
controls. Wiring errors can cause
improper and dangerous operation.
28
E33 FPI Direct Vent Gas Insert
INSTALLATION
For PROPANE Units and Units Equipped with DC Spark Boxes*
*For installation of the DC Spark Box refer to the LP Conversion instructions in this manual.
OPTIONAL REMOTE CONTROL
ON
HI
THTP TP TH
2) Connect the wires as per the wiring diagrams
below.
PILO
T
1) Choose a convenient location on the wall
to install the receiver and the receptacle
box (protection from extreme heat is very
important). Run wires from the fireplace to
that location. Use Thermostat Wire Table.
3) Install 3 AAA alkaline batteries in transmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
OFF
The remote control kit comes with a hand held
transmitter, a receiver and a wall mounting
plate.
CAUTION
Do not connect the millivolt
remote control wires
to the 120V wires.
LO
Use the FPI Remote Control Kit approved for
this unit. Use of other systems may void your
warranty.
To thermopile
E33 FPI Direct Vent Gas Insert
To wall switch,
remote control
or thermostat
OPTIONAL WALL
THERMOSTAT
A wall thermostat may be installed if desired,
follow the wiring diagram below. Note: the wires
are connected to the "TH" on the gas valve. Use
the table below to determine the maximum wire
length. FPI offers an optional programmable
thermostat but any 250-750 millivolt rated nonanticipator type thermostat that is CSA, ULC
or UL approved may be used.
It is recommended that the thermostat be
installed on an interior wall.
CAUTION
Do not connect the millivolt
wall thermostat wires
to the 120V wires.
29
OPERATING INSTRUCTIONS
Thermostat Wire Table
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
Max. Length
14 GA.
16 GA.
18 GA.
20 GA.
22 GA.
50 Ft.
32 Ft.
20 Ft.
12 Ft.
9 Ft.
FINAL CHECK
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly. This includes:
1) Clocking the appliance to ensure the
correct firing rate (rate noted on label) at
15 minutes.
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
IMPORTANT: Gas on/off knob cannot be
turned from "PILOT" to "OFF" unless it is
partially depressed.
During the first few fires, a white film
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the film will bake on and
become very difficult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
1) Turn burner OFF using "ON/OFF" switch.
OPERATING
INSTRUCTIONS
1) Read and understand these instructions
before operating this appliance.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow
the unit to burn for 15 min. to stabilize.
4) Make sure the glass in the door frame is
properly positioned. Never operate the
appliance with the glass removed.
3) Check for proper draft.
5) Verify that the venting and cap are
unobstructed.
CAUTION
Any alteration to the product that
causes sooting or carboning that
results in damage to the exterior
facia is not the responsibility of
the manufacturer.
FIRST FIRE
The first fire in your stove is part of the paint
curing process. To ensure that the paint is
properly cured, it is recommended that you
burn your fireplace for at least four (4) hours
the first time you use it with the fan on. When
first operated, the unit will release an odour
caused by the curing of the paint, the burning
off of any oils remaining from manufacturing.
Smoke detectors in the house may go off at
this time. Open a few windows to ventilate the
room for a couple of hours.
The glass panel may require cleaning after the
unit has cooled down.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS HOT.
Note: When the glass is cold and the
appliance is lit, it may cause
condensation and fog the glass.
This condensation is normal and
will disappear in a few minutes as
the glass heats up.
30
2) Turn gas control knob so indicator points
to "OFF" position and allow 5 minutes for
any gas in the combustion chamber to
escape.
3) Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depress the gas control knob fully. Depress
the ignitor button several times until the
pilot lights. After approximately one minute,
release the gas control knob. The pilot flame
should continue to burn. If the pilot does not
remain lit, repeat operation allowing a longer
period before releasing gas control knob.
4) When the pilot stays lit, turn the gas knob
further counterclockwise to the "ON"
position.
5) Reinstall the glass door (refer to the
"Standard Flush Door" section).
6) Use the switch, thermostat or remote control
to turn on the unit.
7) Rotate the flame height regulator to adjust
the flame height higher or lower.
6) Ensure that the brick panels, if used, are
installed.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
LIGHTING
PROCEDURE
SHUTDOWN
PROCEDURE
1) Use the switch, thermostat or remote control
to turn off the main burner.
2) Turn the main gas control clockwise to the
"OFF" position to turn off the pilot.
3) Turn off all electric power to appliance if
service is to be performed.
IMPORTANT
Prior to igniting or reigniting the
pilot, remove the glass door.
NOTE: For all propane units and units
equipped with electric spark boxes,
see "Copy of Lighting Plate Instructions" section for more details.
Only when the pilot holds, without pressure
being applied to the control knob, should you
reinstall the glass door. The unit must not be
operated with the glass door removed.
E33 FPI Direct Vent Gas Insert
OPERATING INSTRUCTIONS
COPY OF LIGHTING INSTRUCTION PLATE
AUTOMATIC
CONVECTION
FAN OPERATION
The fan operates automatically. Turn the knob on
the side of the faceplate to adjust to the desired
speed. The fan will turn on as the stove comes
up to operating temperature. After the unit has
been turned off and the unit has been cooled
to below useful heat output range, the fan will
shut off automatically.
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds
from your gas appliance. This is perfectly normal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listed below are some examples. All are normal
operating sounds and should not be considered
as defects in your appliance.
Blower:
FPI gas appliances use high tech blowers to
push heated air farther into the room. It is not
unusual for the fan to make a "whirring" sound
when ON. This sound will increase or decrease
in volume depending on the speed setting of
your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a different
gauge material from the rest of the firebox and
body. Therefore, the varying thicknesses of steel
will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit. These
sounds will likely re-occur. Again, this is normal
for steel fireboxes.
OFF
Blower Thermodisc:
When thermally activated switch turns ON, it
will create a small "clicking" sound. This is the
contact switch closing.
Pilot Flame:
While the pilot flame is on it will make a slight
"whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be heard. This is normal
operation of a gas regulator or valve.
a
Regency Gas Fireplace
Unit Body and Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting in
some "cracking" and "ticking" sounds which will
be heard throughout the cycling process.
31
MAINTENANCE
MAINTENANCE
INSTRUCTIONS
1) Always turn the gas valve to the off position
before cleaning. For relighting, refer to
lighting instructions. Keep the burner and
control compartment clean by brushing and
vacuuming at least once a year.
When cleaning the logs, use a clean soft
paint brush as the logs are fragile and easily
damaged.
2) Clean (never when unit is hot) appliance,
door and louvers with a damp cloth. Never
use an abrasive cleaner. The optional
finishes on louvers and doors may be
scratched if abrasives are used to clean
them. The heater is finished in a heat
resistant paint and should only be refinished
with heat resistant paint (not with wall paint).
FPI uses StoveBrite Paint - Metallic Black
#6309.
3) Make a periodic check of the burner for
proper position and condition. Visually
check the flame of the burner periodically,
making sure the flames are steady: not
lifting or floating. If there is a problem, call
a qualified service person.
4) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
During the annual service call, the burners
should be removed and cleaned from the
burner tray.
CLOTHING OR OTHER
FLAMMABLE MATERIAL SHOULD
NOT BE PLACED ON OR NEAR
THE APPLIANCE.
6) Each time the appliance is lit, it may cause
condensation and fog the glass. This
condensation and fog is normal and will
disappear in a few minutes as the glass
heats up.
Never operate the appliance without the
glass properly secured in place or with
the door open.
7) Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the appliance
and to replace nay part of the control system
and any gas control which has been under
water.
8) Periodically check the pilot flames. Correct
flame pattern has three strong blue flames: 1
flowing around the thermopile and 1 around
the thermocouple, and 1 flowing across the
front of the burner.
Note: If you have an incorrect flame pattern,
contact your FPI dealer for further
instructions.
Front Burner Tube
CAUTION: ANY SAFETY SCREEN
OR GUARD REMOVED FOR
SERVICING AN APPLIANCE
MUST BE REPLACED PRIOR TO
OPERATING THE APPLIANCE.
32
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or
streaks, and in extreme cases, holes.
These components should be replaced
immediately.
2) Remove the Termination Cap, and shine a
flashlight down the Vent. Remove any bird
nests, or other foreign material.
3) Check for evidences of excessive
condensation, such as water droplets forming
in the inner liner, and subsequently dripping
out the joints. Continuous condensation can
cause corrosion of caps, pipe, and fittings.
It may be caused by having excessive
lateral runs, too many elbows, and exterior
portions of the system being exposed to
cold weather.
4) Inspect joints to verify that no pipe
sections or fittings have been disturbed,
and consequently loosened. Also check
mechanical supports such as Wall Straps,
or plumbers' tape for rigidity.
LOG REPLACEMENT
5) Keep the area near the appliance clear and
free from combustible materials, gasoline
and other flammable vapours and liquids.
WARNING: CHILDREN AND
ADULTS SHOULD BE ALERTED
TO THE HAZARDS OF HIGH
SURFACE TEMPERATURE AND
SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD
BE CAREFULLY SUPERVISED
WHEN THEY ARE IN THE SAME
ROOM AS THE APPLIANCE.
GENERAL VENT
MAINTENANCE
Incorrect flame pattern will have small, probably
yellow flames, not coming into proper contact
with the rear of the burner or thermopile.
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the
logs. The pilot light generates enough heat to
burn someone. If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagram under Log
Installation.
NOTE: Improper positioning of logs may
create carbon build-up and will alter the unit’s
performance which is not covered under
warranty.
GLASS GASKET
If the glass gasket requires replacement use
a tadpole gasket for the Flush Front (Part #
936-155).
STEEL OR GOLD TRIM
Front Burner Tube
Top View of pilot flame
The steel or 24 carat gold plated finish on the
louvers requires little maintenance, and need
only be cleaned with a damp cloth. DO NOT use
abrasive materials or chemical cleaners, as they
may harm the finish and void the warranty.
Clean any fingerprints off before turning the
unit on. If the top louvers start to discolour,
check the door gasket seal and replace if
necessary.
E33 FPI Direct Vent Gas Insert
MAINTENANCE
DOOR GLASS
Your FPI stove is supplied with high temperature,
5 mm Neoceram ceramic glass that will withstand
the highest heat that your unit will produce. Do
not abuse the glass by striking the surface or
by slamming the door shut.
9) Remove the rear log support by unscrewing
the 2 screws.
To Remove Fan:
1) Turn the unit off and allow it to cool down to
room temperature.
2) Unplug or disconnect power source to stove.
3) Remove the flush door (refer to p.14).
If your glass requires cleaning, we recommend
using an approved glass cleaner available at
all authorized dealers. Do not use abrasive
materials. Do not clean the glass when hot.
4) Remove logs and grate (refer to p.10).
In the event that you break your glass by
impact, purchase your replacement from an
authorized FPI dealer only, do not use substitute
materials. Follow our step-by-step instructions
for replacement. Warning: Wear gloves when
removing damaged or broken glass.
6) Remove base brick set. (When removing
base brick sides the two screws that hold
the grate down must be removed first).
Caution: Do not operate appliance with
glass panels removed, cracked or broken.
Replacement of the glass should be done
by a licensed or qualified service person.
Screws
5) Remove optional brick panel set, if installed
(refer to the "Optional Brick Panel" section).
10) Remove the 12 screws holding the Access
Panel in place.
Screws
Flush Glass Replacement
Remove the flush door front (refer to the
"Standard Flush Door" section). Remove the 4
glass clips from each corner. Slide in the new
replacement glass. Push the 4 glass clips back
onto the frame.
7) Straighten the adjustment wire under the
firebox base.
Fan Access Plate Screws
11) Unplug the wires from the fan motor (from
inside the stove).
Air Shutter Wire
Straighten adjustment wire.
8) Remove the Burner by removing the 2
screws (1 on burner bracket and one on
valve tray). Tilt up the left burner and slide
to the left away from the orifice.
12) Remove the 2 screws from the fan
bracket.
FAN MAINTENANCE
If your fan requires maintenance or replacement,
access to the fan is through the plate on the
floor of the firebox. NOTE: the unit MUST NOT
be operated without the fan access panel
securely in place.
Screws
Screws
Caution: Label all wires prior to
disconnecting when servicing controls.
Wiring errors can cause improper and
dangerous operation. Verify proper
operation after servicing.
E33 FPI Direct Vent Gas Insert
33
MAINTENANCE
13) Pull Fan Assembly forward, to disengage
the fan clip on the rear wall. Then lift the
Fan Assembly up and pull through firebox
opening.
7) Remove base brick set. (When removing
base brick sides the two screws that hold
the grate down must be removed first).
11) Disconnect the inlet gas line.
12) Unplug the black and red wires at the valve.
Undo the 2 TP wires at the valve.
13) Remove the 17 screws on the valve tray.
Screws
8) Straighten the adjustment wire under the
firebox base.
14) Take out the valve tray from the unit.
14) Disconnect green wire from power cord.
Air Shutter Wire
Straighten adjustment wire.
9) Remove the Burner by removing the 2
screws (1 on burner bracket and one on
valve tray). Tilt up the left burner and slide
to the left away from the orifice.
15) Scrape off the old gasket from the floor of the
firebox and from the valve access plate.
Replacing fan:
16) Install new gasket and valve assembly
(reverse steps 9-14).
15) Reverse above steps.
Seal fan access panel using high temperature
silicone (sparingly).
VALVE ASSEMBLY
REMOVAL AND
INSTALLATION
1) Turn the unit off and allow it to cool down
to room temperature.
Screws
NOTE: Failure to install a new gasket
may severely affect the appliance
performance.
17) Hook up gas line and check for gas leaks
with soap and water solution or a gas leak
detector. Do not use open flame for leak
testing.
10) Remove the rear log support by unscrewing
the 2 screws.
Screws
18) Set up the air shutter to 5/16" for NG and
7/16" for LP.
19) Fire up the unit temporarily.
2) Unplug or disconnect power source.
3) Shut off the main gas supply.
20) Check the manifold pressure 3.8" W.C. for
NG and 11" W.C. for LP.
4) Remove the louvers and glass door.
21) Reverse steps 4-8.
5) Remove logs and grate.
6) Remove optional brick set, if installed.
34
E33 FPI Direct Vent Gas Insert
PARTS LIST
MAIN ASSEMBLY
Part #
Description
1) 340-038
2) 340-103
Fan Access Plate
Gasket - Fan Access Plate
3) 320-517/P
910-331/P
5) 910-750
910-752
910-692
910-737
Fan Assembly 120 V
Fan Motor 120 V
Power Cord
Wire Harness (Faceplate)
Wire Fan to Power Cord
Wire Valve to Spill Switch
7) 910-142
8) *
9) 320-070
Fan Auto On/Off Thermodisc
Thermodisc Bracket
Fan Switch Cover
13) *
17) *
18) *
19) *
Baffle Plate
Wire Holder Clip
Strain Relief
Grommet for Power Cord
340-924
340-922
340-926
21) *
23) *
Flush Louvers (Set) - Black/Gold
Flush Louvers (Set) - Black
Flush Louvers (Set) - Black/Steel
Top Flush Louver
Bottom Flush Louver
340-901
340-902
Brick Panel Set - Standard Brown
Brick Panel Set - Standard Red
33) *
34) *
35) *
36) *
37) 340-094
340-043
340-528
Brick Clip
Trim Brick Front
Base Brick Panel (3pc)
43) *
45) *
46) *
47) *
48) 340-523
49) 340-099
50) *
51) *
Stove Top
Adaptor Stop
Adaptor Holding Brkt - Left
Adaptor Holding Brkt - Right
Flue Adaptor Assembly
Thermal Insulation
Insulation Hold Down Bracket
Louver Hold Down - Top
918-513
Brick Panel - Right
Brick Panel - Left
Brick Panel - Back
Manual
* Not available as a replacement part.
E33 FPI Direct Vent Gas Insert
35
PARTS LIST
BURNER & LOG ASSEMBLY
Part #
Description
52) 340-104
Gasket - Valve Tray
340-574/P
340-576/P
56) 910-190
57) 910-478
59) *
Valve Assembly - NG
Valve Assembly - LP
Piezo Ignitor and Nut
Valve - S.I.T. - Natural Gas / Propane
Valve Tray
910-034
66) 910-038
910-039
67) 904-690
904-641
936-170
Pilot Assy-3 Flame Conv. - NG
Pilot Assy-3 Flame-S.I.T.-NG
Pilot Assy - 3 Flame - S.I.T. - LP
Orifice #31 - NG
Orifice #50 - LP
Orifice Gasket
79) 948-433
82) 340-047
Burner Assy - NG/LP
Burner Grate
340-930
*
*
*
*
*
*
*
*
Complete Log Set
Bottom Log
Center Top Log
Front Log
Left Log
Right Log
Top Left Log
Rear Log
Top Right Log
* Not available as a replacement part.
36
E33 FPI Direct Vent Gas Insert
PARTS LIST
FULL SCREEN FRONT
Part #
83) *
84) 340-910
85) *
86) *
87) *
88) *
89) 910-199
90) 948-042
Description
Top Frame
Full Screen Door - Black
Full Screen Left Door
Full Screen Right Door
Bottom Frame
Screw #8 x 1/2 Self Tapping
Wire Clip Holder
Hinge Spring
83
89
84
88
88
88
88
85
87
90
90
86
E33 FPI Direct Vent Gas Insert
37
PARTS LIST
FACEPLATES, TRIMS AND HEARTHS
Part #
Description
Part #
340-918
340-919
74) 904-569
91) *
92) *
93) *
Faceplates and Trim (Complete) w/ Black Trim
Oversized Faceplate
Fan Speed Control Knob
Faceplate Side - Right
Faceplate - Top
Faceplate Side - Left Assy
340-532
340-533
94) *
95) *
96) *
Trim Set Packaged - Black
Oversized Trim Set Packaged - Black
Trim Side - Right
Trim - Top
Trim Side - Left Assy
97) 910-246
98) 910-330
99) *
Burner ON/OFF Switch
Fan Speed Control 120 V
Faceplate Filler
172)
176)
180)
184)
186)
190)
191)
199)
Description
320-940
320-942
320-944
320-946
904-586
*
*
948-216
Hearth Trim - 1"
Hearth Trim - 2"
Hearth Trim - 4"
Hearth Trim - 6"
Speed Control Knob c/w Spring Clip
Screw #8 x 1/2" Black Self-tapping
Screw #8 x 1/2" Brass Plated Self-tapping
Regency® Logo
* Not available as a replacement part.
97
95/96
92
91
99
93
94
98
96
LOG
OPL
OPLAT
ATEEHE
HERRE
E
199
REAR VIEW
(ASSEMBLED)
191
172
176
180
FRONT VIEW
184
38
E33 FPI Direct Vent Gas Insert
PARTS LIST
CONTEMPORARY FACEPLATE & DOOR FRAME
Part #
341-914
90) *
91) *
92) *
93) *
910-246
910-330
904-569
Description
Contemporary Faceplate & Door Frame
Complete Faceplate
Door Frame
Bottom Louver
Hinges
Burner ON/OFF Switch
Fan Speed Control 120V
Fan Speed Control Knob
* Not available as a replacement part.
E33 FPI Direct Vent Gas Insert
39
PARTS LIST
LOW PROFILE FACEPLATE
Part #
1)
2)
3)
4)
5)
*
*
*
*
*
Description
Backplate Assembly
Bottom Louver
Right mounting bracket
Left mounting bracket
Front Frame
5
4
1
2
3
40
E33 FPI Direct Vent Gas Insert
NOTES
E33 FPI Direct Vent Gas Insert
41
NOTES
42
E33 FPI Direct Vent Gas Insert
WARRANTY
Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit
thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a
Excalibur Product. This warranty is not transferable.
The Warranty: Limited Lifetime
The combustion chamber, heat exchanger, burner tubes/pans, logs, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime
Warranty for five (5) years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5) years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date
of purchase and parts only thereafter.
Special Finishes - One year on brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating
and cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks,
ie. finger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Electrical and mechanical components such as blowers, switches, wiring, thermodiscs, FPI remote controls, spill switches, thermopiles, thermocouples, pilot assembly components,
and gas valves are covered for two years parts and one year subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and
continue as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.
FPI venting components are covered parts and subsidized labour* for three (3) years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.
Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any
item shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided
that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of
installation. Reported damage after this time will be subject to rejection.
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated
for manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from
unauthorized service persons or dealers.
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name,
purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.
ie. as products evolve, field modifications or upgrades will not be performed.
FPI will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence
or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI, may nullify your warranty
on this product.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.
* Subsidy according to job scale as predetermined by FPI.
E33 FPI Direct Vent Gas Insert
43
Register your Regency® warranty online
www.regency-fire.com
Reasons to register your product online today!
• View and modify a list of all your registered products.
• Request automatic email notification of new product updates.
• Stay informed about the current promotions, events, and special
offers on related products.
Installer: Please complete the following information
Dealer Name & Address: ______________________________________________
___________________________________________________________________
Installer: ___________________________________________________________
Phone #: ___________________________________________________________
Date Installed: ______________________________________________________
Serial No.: __________________________________________________________
Regency and Excalibur are trademarks of FPI Fireplace Products International Ltd.
© Copyright 2010, FPI Fireplace Products International Ltd. All rights reserved.
Printed in Canada
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising