140CR Electronic Cash Register (140CR small drawer model) User's Manual START-UP is QUICK and EASY! Simple to use! 20 departments and 120 PLUs Automatic Tax Calculations Calculator function CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan EU DI UK INTRODUCTION Thank you very much for purchasing this CASIO electronic cash register. START-UP is QUICK and EASY! Part-1 of this User's Manual can help you make a quick start. Once you have mastered the QUICK START operations, you will undoubtedly want to expand your use of this machine by studying other sections of Part-2. Original Carton/Package If for any reason, this product is to be returned to the store where purchased, it must be packed in the original carton/package. Power Supply Your cash register is designed to operate on standard household current (120V, 220V, 230V or 240V; 50/60Hz). Do not overload the outlet by plugging in too many appliances. Location Locate the Cash register on a flat, stable surface, away from heaters or areas exposed to direct sunlight, humidity or dust. Cleaning Clean the cash register exterior with a soft cloth which has been moistened with a solution of a mild neutral detergent and water, and wrung out. Be sure that the cloth is thoroughly wrung out to avoid damage to the printer. Never use paint thinner, benzene, or other volatile solvents. The mains plug on this equipment must be used to disconnect mains power. Please ensure that the socket outlet is installed near the equipment and shall be easily accessible. E 2 INTRODUCTION Safety precautions • To use this product safely and correctly, read this manual thoroughly and operate as instructed. After reading this guide, keep it close at hand for easy reference. Please keep all informations for future reference. • Always observe the warnings and cautions indicated on the product. About the icons In this guide various icons are used to highlight safe operation of this product and to prevent injury to the operator and other personnel and also to prevent damage to property and this product. The icons and definitions are given below. Indicates that there is a risk of severe injury or death if used incorrectly. Indicates that injury or damage may result if used incorrectly. Icon examples To bring attention to risks and possible damage, the following types of icons are used. The symbol indicates that it includes some symbol for attracting attention (including warning). In this triangle the actual type of precautions to be taken (electric shock, in this case) is indicated. The symbol indicates a prohibited action. In this symbol the actual type of prohibited actions (disassembly, in this case) will be indicated. The symbol indicates a restriction. In this symbol the type of actual restriction (removal of the power plug from an outlet, in this case) is indicated. Warning! Handling the register Should the register malfunction, start to emit smoke or a strange odor, or otherwise behave abnormally, immediately shut down the power and unplug the AC plug from the power outlet. Continued use creates the danger of fire and electric shock. • Contact CASIO service representative. Do not place containers of liquids near the register and do not allow any foreign matter to get into it. Should water or other foreign matter get into the register, immediately shut down the power and unplug the AC plug from the power outlet. Continued use creates the danger of short circuit, fire and electric shock. • Contact CASIO service representative. Should you drop the register and damage it, immediately shut down the power and unplug the AC plug from the power outlet. Continued use creates the danger of short circuit, fire and electric shock. • Attempting to repair the register yourself is extremely dangerous. Contact CASIO service representative. Never try to take the register apart or modify it in any way. High-voltage components inside the register create the danger of fire and electric shock. • Contact CASIO service representative for all repair and maintenance. Power plug and AC outlet Use only a proper AC electric outlet. Use of an outlet with a different voltage from the rating creates the danger of malfunction, fire, and electric shock. Overloading an electric outlet creates the danger of overheating and fire. Make sure the power plug is inserted as far as it will go. Loose plugs create the danger of electric shock, overheating, and fire. • Do not use the register if the plug is damaged. Never connect to a power outlet that is loose. E 3 INTRODUCTION Warning! Use a dry cloth to periodically wipe off any dust built up on the prongs of the plug. Humidity can cause poor insulation and create the danger of electric shock and fire if dust stays on the prongs. Do not allow the power cord or plug to become damaged, and never try to modify them in any way. Continued use of a damaged power cord can cause deterioration of the insulation, exposure of internal wiring, and short circuit, which creates the danger of electric shock and fire. • Contact CASIO service representative whenever the power cord or plug requires repair or maintenance. Caution! Do not place the register on an unstable or uneven surface. Doing so can cause the register — especially when the drawer is open — to fall, creating the danger of malfunction, fire, and electric shock. Do not place the register in the following areas. • Areas where the register will be subject to large amounts of humidity or dust, or directly exposed to hot or cold air. • Areas exposed to direct sunlight, in a close motor vehicle, or any other area subject to very high temperatures. The above conditions can cause malfunction, which creates the danger of fire. Do not overlay bend the power cord, do not allow it to be caught between desks or other furniture, and never place heavy objects on top of the power cord. Doing so can cause short circuit or breaking of the power cord, creating the danger of fire and electric shock. Be sure to grasp the plug when unplugging the power cord from the wall outlet. Pulling on the cord can damage it, break the wiring, or cause short, creating the danger of fire and electric shock. Never touch the plug while your hands are wet. Doing so creates the danger of electric shock. Pulling on the cord can damage it, break the wiring, or cause short, creating the danger of fire and electric shock. At least once a year, unplug the power plug and use a dry cloth or vacuum cleaner to clear dust from the area around the prongs of the power plug. Never use detergent to clean the power cord, especially power plug. Keep small parts out of the reach of small children to make sure it is not swallowed accidentally. E 4 Contents Getting to know your cash register .................................................................... Daily Job Flow ................................................................................................... Part-1 1. 2. 3. 4. 5. 1. 2. 9 10 11 13 17 19 CALCULATOR FUNCTION ............................................................. 36 Calculator Mode.......................................................................................... 36 Part-4 1. 2. CONVENIENT OPERATION ............................................................ (Please keep these sections to expand your use.) 9 Various Programming ................................................................................. 19 Various Operations ..................................................................................... 30 Part-3 1. QUICK START OPERATION ........................................................... (You can operate this ECR on a basic level by reading the following sections) Initialization ................................................................................................. Loading Paper ............................................................................................ Basic Programming for QUICK START – TIME/DATE ................................ Basic Operation after Basic Programming .................................................. Daily Management Report .......................................................................... Part-2 6 8 USEFUL INFORMATION ................................................................. 38 Troubleshooting .......................................................................................... 38 Specifications.............................................................................................. 38 Basic Components and Accessories Printer cover Operator display Mode switch Keyboard Drawer (140CR small drawer model) Accessories Roll paper Mode keys Drawer keys User's manual Fixing hook (M drawer model only) Magnetic plate* 1 pc 2 pcs 1 pc 2 pcs 1 pc * Use this plate for tacking the notes received from customer. Weld lines Lines may be visible on the exterior of the product. These are “weld lines” that result from the plastic molding process. They are not cracks or scratches. E 5 Getting to know your cash register Getting to know your cash register Mode Switch CAL X REG The position of the Mode Switch controls the type of operations you can perform on the cash register. The PROGRAM key (marked PGM) can be select any Mode Switch setting, while OPERATOR key (marked OP) can be used to select OFF, REG or CAL only. Z OFF PGM RF OFF REG CAL X Z OP key ● ● ● PGM key ● ● ● ● ● ● ● RF PGM PGM OP OP key PGM key Note: An error is generated (E01 displayed) whenever the position of the Mode Switch is changed during registration. OFF In this position, the power of the cash register is off. REG (Register) This is the position used for registration of normal transactions. RF (Refund) This is the position used for registration of refunds. CAL (Calculator) This is the position used for calculator mode. PGM (Programming) This is the position used to program the cash register to suit the needs of your store. X (Read) This is the position used to produce reports of daily sales totals without clearing the totals. Z (Reset) This is the position used to produce reports of daily sales totals. This setting clears the totals. Display ! ! Department Number Display Anytime you press a department key to register a unit price, the corresponding department number appears here. # Number of Repeat Display Anytime you perform “repeat registration” (page 13), the number of repeats appears here. Note that only one digit is displayed for the number of repeats. $ Numeric Display Entered values (unit prices or quantities) and calculated values (subtotals, totals or change amount due) are displayed here. The capacity of the display is 8 digits. @ PLU Number Display This part of the display can be used to show the Anytime you perform a PLU registration, the current time or date between registrations (page corresponding PLU number appears here. 33). E 6 Getting to know your cash register Keyboard FEED s DATE TIME AC C & — ERR. CORR PLU 4 5 9/14/19 10/15/20 ( 7 8 9 w 4 5 6 s 1 2 3 ' 0 00 . 3 8/13/18 2 7/12/17 1 6/11/16 % CLK# RA MR TAX PGM PO " # DEPT CHK NS SHIFT # $ SUB CH TOTAL % CA AMT TEND = Certain keys have two functions; one for register mode and one for calculator mode. In this manual, we will refer to specific keys as noted below to make the operations as easy to understand as possible: Register Mode ! l @ h Multiplication/ Date Time key # t Clear key $ g Minus/ Error Correction key % i PLU (Price Look Up) key ^ : Percent/Cashier ID No. Assignment key & ~ Tax Program key * . Received on Account key ( ] Paid Out key ) j Reference Number/Department Shift key Q m Check/No Sale key W k Subtotal key E u Charge key R p Cash Amount Tendered key T ?, Z, ~ >, ' Numeric keys and 2-zero key Y " U G, S, D, F, [ Department keys Feed key Decimal key • Department 6 through 20 are specified by pressing the j key respectively as follows: jG ~ j[ → Department 6 ~ 10 jjG ~ jj[ → Department 11 ~ 15 jjjG ~ jjj[ → Department 16 ~ 20 Calculator Mode # t AC key ^ : Percent key * . Memory Recall key Q m Drawer Open key R p Equal key T ?, Z, ~ >, ' Numeric keys and 2-zero key Y " Decimal key U H, J, K, L Arithmetic Operation key E 7 Daily Job Flow Daily Job Flow Before Opening The Store 1. 2. 3. 4. Plugged in? Enough Roll Paper? Page-10 Date and Time is correct? Page-33 Enough small change in the drawer? Page-34 While The Store Is Open 1. Registrations. Page-13 ~ 2. Issuing latest daily sales total if needed. (Generating report by Mode Switch to X position.) Page-17 After Closing The Store 1. Issuing Daily Sales Total. (Resetting report by Mode Switch to Z position.) Page-17 2. Picking up money in the drawer. Page-34 3. Turn the Mode Switch to OFF. Other 1. Troubleshooting E 8 Page-38 Part-1 QUICK START OPERATION Part-1 QUICK START OPERATION 1. Initialization / Loading Memory Protection Battery Part-1 ◗ To initialize the cash register Important You must initialize the Cash register. 1. 2. 3. 4. Set the Mode Switch to OFF. Load the memory protection batteries. Plug the power cord of the cash register into an AC outlet. Set the Mode Switch to REG. Note: To prevent to lose all of your settings and sales data, we reccomend you to install the memory protection batteries. ◗ To load the memory protection batteries 1. Remove the printer cover. 2. Open the battery compartment cover. 3. Load 3 new UM-3, or R6P (SUM-3) type batteries into the compartment. Be sure that the plus (+) and minus (–) ends of each battery are facing in the directions indicated by the illustrations inside the battery compartment (Figure 1). 4. Replace the memory protection battery compartment cover back into place. 5. Replace the printer paper and printer cover. (Figure 1) REPLACE MEMORY PROTECTION BATTERIES AT LEAST ONCE EVERY YEAR. E 9 Part-1 2. QUICK START OPERATION Loading Paper Roll And Replacing The Printer’s Ink Roll Mode Switch REG CAL X Z * Replace the printer cover by * Load new paper following the placing the cover’s front tab into the register’s groove. instructions above, and replace the printer cover. OFF RF PGM 1. To load journal paper ! Remove the printer cover by lifting up the back. 2. To remove journal paper ! Remove the printer cover fol- Default printer setting is for lowing the instructions above. Journal. @ Press the l key until ap- To print receipts, please refer to proximately 20cm of the pa- 1-7-3 on page 24 to switch the per is fed from the printer. printer for Receipt or Journal. # Cut off the roll paper. @ Put a roll of journal paper into the holder. # Cut the leading end of the roll paper with scissors and insert the paper into the inlet. ◗ To load receipt paper ! To use the printer to print re- ceipts, follow steps 1 through 4 of “To load journal paper”. @ Pass the leading end of the receipt paper through the $ Remove the take-up reel printer cover’s paper outlet from the printer and take off and replace the printer cover. the left plate of the reel. # Tear off any excess paper. % Remove the journal paper from the take-up reel. $ Press the l key until 20 or 30 cm of paper is fed from the printer. % Roll the paper onto the takeup reel a few turns. ^ Cut off the paper left in the printer and press the l key until the remaining paper is fed out from the printer. ^ Set the left plate of the take- up reel and place the reel into the register. & Remove the core of the pa- per. & Press the l key to take up any slack in the paper. E 10 Options: Roll paper – P-5860 Ink Roll – IR-40 Part-1 QUICK START OPERATION 3. Basic Programming for QUICK START Mode Switch CAL X REG Z OFF RF Procedure 1. Turn the mode switch to PGM position. Part-1 PGM Purpose Programming 2. When the display shows blinking “0”, such as 00-00-00 , enter current date in Day, Month, Year order. Example: 8, January, 2010: enter ?<?ZZ? • Enter 6-digit, last 2 digits for year set. (2010 → 10) • If you have changed the date order (page-12), enter date of that order. • By pressing y, this procedure returns one by one. Setting the current date 00-00 , 3. When the display shows blinking “0”, such as enter current time in Hour, Minute order. Example: 1:18 PM, enter ZCZ< • Enter 4-digit, use 24-hour system. • By pressing y, this procedure returns one by one. • If you want to adjust the date/ time, please refer to page 33 of this manual. Setting the current time 4. Input the desired add-in tax rate to the appropriate department key. (This procedure below programs add-in tax rate only. If you want to set add-on tax or tax with special rounding, refer to page 26 of this manual.) A) Press the ~ key. B) Enter tax rate. (Example: For 6% enter “6”, 5.75% enter “5.75”.) C) Press the appropriate department key. D) Repeat step B) and C) to set other department key. E) Press the k key to end tax programming. Note: In case of setting the wrong tax rate to the key, please enter ? and press those department keys above, and quit this procedure by pressing k key, and Setting the tax rates start from the beginning of this procedure. Example : Set add-in tax 8% to department 2, 3, 15% to department 4 key. ~ Start tax program. 8S Enter tax rate and press dept key. 8D Enter tax rate and press dept key. 15F Enter tax rate and press dept key. k To end the setting. E 11 Part-1 QUICK START OPERATION Procedure 5. To select the date format and monetary mode (if necessary) You can select the date format and monetary mode after initialization depending on the requrements in your area. Default date format is Day/ Month/ Year and default monetary mode is add 2. Ck Date Format Selections P3 appears in mode display A ?ZXX k Program set code No. X? p Select number from list A (To end the setting) ? Month/ Day/ Year Z Day/ Month/ Year X Select date format and monetary mode Monetary Mode Selections Add 0 (0.) ? B k Select number from list B Year/ Month/ Day Purpose Add 1 (0.0) Z Add 2 (0.00) X Procedure 6. In case of accepting two (the Euro and the local) currencies. 6-1. Press the following keys to define the main currency/print out currency of the subtotal. Ck Purpose P3 appears in mode display XVXX k Zp Euro Status k (to end the setting) Euro status (1) Main currency = Local, Print out subtotal = Local: ? (2) Main currency = Euro, Print out subtotal = Euro : Z (3) Main currency = Local, Print out subtotal = Both: X (4) Main currency = Euro, Print out subtotal = Both : C Setting the Euro 6-2. Press the following keys to set the currency exchange rate against the Euro. Ck P3 appears in mode display Z>>> k Z>MMC p Exchange rate (up to 6 digits) Decimal position k Example: (Exchange rate and decimal position) Currency exchange rate = 1 Euro in local currency Z>BB<CB 1 Euro = 1.95583 DM : (to end the setting) 7. In case of becoming to accept the Euro only. 7-1. You can restrict the registable currency to the Euro only by the following procedure. 1. Turn the mode switch to Z position. 2. Issue all reset report including periodic data. 3. Press the following keys to set. ?Z?MX??Xkp If you want to cancel this operation, press k instead of p. Restricting the Currency to the Euro For Australia only. You can set some programmable options to suit the Australian GST by the following procedure. 1. Turn the mode switch to Z position. 2. Press the following keys to program. ?Z?ZX??Zkp If you want to cancel this operation, press k instead of p. Setting the Australian GST E 12 Part-1 QUICK START OPERATION 4. Basic Operation after Basic Programming Mode Switch REG Note: Whenever an error is generated, the input figures reset to 0. All printout samples are journal images and the header (date, time and consecutive no.) are eliminated from the samples. Example Unit Price Quantity Dept. Cash Amount tendered m •••••••••• Z?? G 01••••1•00 Unit Price Department 1 $1.00 1 1 OFF RF PGM Part-1 4-2 Basic operation Z Printout Operation 4-1 Open the drawer without a sale CAL X $2.00 1 10 $0.30 jX?? [ 1 Department 10 15 $5.00 Department 15 jjC? [ N — No Sale Symbol — Department No./Unit Price 10••••2•00 15••••0•30 •3•30 S •5•00 C •1•70 G — Subtotal — Cash Amount Tendered — Change Amount Due k B?? p Cash amount tendered Departments 6 through 10, 11 through 15, 16 through 20 can also be registered in combination with the j and G, S, D, F or [ keys, respectively. The j key should be entered just before entering unit price manually. 4-3 Multiple registration of the same items Example Unit Price Quantity Dept. Z?? G Department 1 Unit Price G Ch Quantity $1.00 2 1 $1.35 3 2 Multiple key ZCB S k p 01••••1•00 01••••1•00 3 •1•35 — Repeat X — Sales Quantity @ — Unit Price 02••••4•05 •6•05 C Note that repeat registration can be used with unit prices up to 6 digits long. 4-4 Charge sales Example Unit Price Quantity Dept. $1.00 $2.00 $3.00 1 1 1 1 2 1 Z?? G X?? S C?? G k u 01••••1•00 02••••2•00 01••••3•00 •6•00 H — Charge Sales Charge key You cannot perform the amount tendered operation using the u key. E 13 Part-1 QUICK START OPERATION 4-5 Split cash/ charge sales Example Unit Price Quantity Dept. Cash Amount tendered $2.00 $3.00 $4.00 1 1 1 1 2 1 $5.00 4-6 Corrections 4-6-1 Before you press a department key Printout Operation X?? G C?? S V?? G k B?? p u 01••••2•00 02••••3•00 01••••4•00 •9•00 S •5•00 C — Cash Amount Tendered •4•00 H — Charge Sales Corrections can be made while you are registering the item (before you press a department key), or after it has already been registered into the memory (by pressing a department key). y key clears the last item entered. Printout Operation Example 1. Entered 400 for unit price by mistake instead of 100. V?? y Wrong entry 01••••1•00 Clears the last item entered. Z?? G Correct entry 2. Entered unit price first instead of quantity and then pressed h. Registered Department 1 X?? h Unit price Multiplication y 5 •2•00 02•••10•00 X @ 10 X @ Clears the last item entered. Bh Quantity Multiplication X?? S Unit price 3. Entered 150 for unit price by mistake instead of 105. Registered Department 2 Z? h Quantity Multiplication ZB? y Wrong entry Clears the last item entered. Z? h Quantity Z?B D Correct entry E 14 Registered Department 3 •1•05 03•••10•50 Part-1 QUICK START OPERATION Mode Switch REG CAL X Z OFF RF 4-6-2 After you pressed a department key Example 1. Entered unit price 550 by mistake instead of 505 and pressed a department key. Part-1 PGM Printout Operation g key cancels the last registered item. BB? G Wrong entry g 01••••5•50 -5•50 V 01••••5•05 Cancels the last item registered. B?B G Correct entry 2. Entered unit price 220 by mistake instead of 230 and pressed a department key. Registered Department 1 Ch Quantity Multiplication XX? S Wrong entry g Cancels the last item registered. 3 X •2•20 @ 02••••6•60 -6•60 V 3 •2•30 02••••6•90 X @ Ch XC? S Correct entry Registered Department 2 E 15 Part-1 QUICK START OPERATION Mode Switch 4-7-1 Registering with currency exchange REG CAL X Z OFF RF PGM Example Unit Price £2.00 Quantity 3 Dept. 1 1 Cash Amount 10.00 Euro tendered Rate 1Euro = £ 0.8 Main currency Local (£) Printout of ST Both currencies Display Operation Ch X?? G ] k '50e Pressing ] before subtotal converts the subtotal amount into the Euro. Z?' ] 1~00e Pressing ] after amount tendered converts the amount into the Euro. *1 p "00 Press p to finalize the transaction. The change amount in the main currency is shown on the display. *2 p "50e You can switch the currency of change amount repeatedly by pressing the p key. *1 If the payment is the same as the subtotal amount, you can omit this operation. Press p key directly after the subtotal. *2 If the payment is less than the subtotal amount, the cash register specifies it as a partial payment and shows the balance in the main currency on the display. Printout 3 X •2•00 @ 01••••6•00 •6•00 S — Subtotal in the main currency e7•50 @ — Subtotal after conversion e10•00 C — Payment in the Euro @ •8•00 C — Payment after conversion •2•00 G — Change in the main currency e2•50 @ — Change in the sub currency E 16 Part-1 QUICK START OPERATION 5. Daily Management Report This section tells you the procedures to use to produce reports of the transaction data stored in the cash register's memory. 5-1 Financial Report CAL REG Printout Operation h Mode Switch XZ 08-01-10 12-35#0085 158 OFF •16676•48 RF 46 •16675•99 •16518•99 PGM •92•00 •70•00 5-2 General Control Read/Reset Report Mode Switch to Z Mode Switch CAL X REG (Read) (Reset) — Date — Time/Consecutive No. X — Read Symbol * — Gross Sales No. of items * — Gross Sales Amount n — Net Sales No. of Customers n — Net Sales Amount C# — Cash Total in Drawer H# — Charge Total in Drawer *K — Check Total in Drawer Printout Operation Z (Reset) report — Clerk No./Date 1#08-01-10 — Time/Consecutive No. 19-35#0086 No. of 0001 ZZ — Non-resettable *1 *1 5-2-1 Daily Read/Reset Report Mode Switch to X Part-1 Important Remember that when you issue a reset (Z) report, the data that is reported is cleared from the applicable totalizers. To view data without clearing totalizers, issue a read (X) report. Resets /RESET Symbol p p 01••••••48 •166•94 02••••••61 •1259•15 — Dept. No./ No. of Items — Amount 03••••••44 •15175•39 20•••••••5 •75•00 158 * •16676•48 * — Gross Sales No. of Items — Gross Sales Amount Z OFF RF PGM E 17 Part-1 QUICK START OPERATION •1•40 - — Reduction Amount •0•91 %- — Premium/Discount Amount •1182•64 T — Taxable Amount for Tax Rate 1 •62•07 t1 — Tax Amount for Tax Rate 1 •167•45 *T — Taxable Amount for Tax Rate 2 •16•75 t™ — Tax Amount for Tax Rate 2 46 n •16675•99 n 1•16675•99 — Net Sales No. of Customers — Net Sales Amount — Clerk 1 Sales Amount (Refer to 2-8 Cashier Assignment) 47 C — Cash Sales Count — Cash Sales Amount — Charge Sales Count — Charge Sales Amount K — Check Sales Count K — Check Sales Amount R — Received On Account Amount P — Paid Out Amount V — Error Correction Count r — Refnd Mode Count r — Refund Mode Amount CX — No. of p key operation in CAL mode N — No sale Count C# — Cash in Drawer H# — Charge in Drawer *K — Check in Drawer •16513•99 C 4 H •92•00 H 1 •70•00 •15•00 •10•00 4 1 •3•00 16 1 •16518•99 •92•00 •70•00 000001 6675•99 — Non-resettable Grand Sales total (Printed only on RESET report) *2 X (Read) report is the same except *1 and *2. 5-2-2 Periodic Read/ Reset Report Mode Switch to Z Operation or X Z?p Printout 08-01-10 — Date — Time/Conseccutive No. 19-50#0087 #10#•••• X — Periocic Read Symbol X 77 * •1116•90 * 11 n •1116•90 n E 18 — Gross Sales No. of Items — Gross Sales Amount — Net Sales No. of Customers — Net Sales Amount Part-2 CONVENIENT OPERATION Part 2 CONVENIENT OPERATION Mode Switch CAL X REG 1. Various Programming OFF 1-1 Unit price for Departments RF PGM Zk Example Unit Price Dept. Z $1.00 $2.20 $11.00 1 2 3 P appears in mode display (For Dept. 1) (For Dept. 2) Part-2 Z?? G XX? S ZZ?? D k (For Dept .3) • Unit prices within the range of 0.01~9999.99. 1-2 Rate for percent key Example Discount Rate Zk 2.5% P appears in mode display X"B : k (To end the setting) • The rate within the range of 00.01 to 99.99%. 1-3 To change tax status for Departments Example Status Depts. Taxable 1 Taxable 2 1 7 Tax status for the Departments 1 ~ 20 are initialized as Non-Taxable. Z k~ P appears in mode display .G Select key from list A For Dept. 1 j] S Taxable status 2 For Dept. 7 k (To end the setting) Selections Taxable status 1 . Taxable status 2 ] Taxable status 3 u Taxable status 4 h Non-taxable status m A E 19 Part-2 CONVENIENT OPERATION 1-4 Status for Department Mode Switch CAL X REG Example Depts. 1 2 OFF Selections A B C 0 4 1 0 5 1 RF PGM Ck P3 appears in mode display ?VZ G For Dept. 1 Select a number from list A Select a number from list B Select a number from list C ?BZ S For Dept. 2 Normal department Single item sale department Maximum No. of digits to be 5 k (To end the setting) Selections Normal department ? Minus department Z No limitation for manually entered price. Maximum number of digits for manually entered price. ? Z~M (1 ~ 7 digits) A B < or > To prohibit manual price entries. Normal sales (not a single-item sale) department ? Set as a single-item sale department Z C 1-5 Status for percent key 1-5-1 To change taxable status The percent key is initialized as Non-taxable. for the percent key Z k~ Example Change Percent ket registration as a Taxable status 1. P appears in mode display .: Select key from list A (For percent key) k (To end the setting) Selections Taxable status 1 . Taxable status 2 ] Taxable status 3 u Taxable status 4 h All taxable status (1, 2, 3 and 4) Non-taxable status E 20 .] m A Z Part-2 CONVENIENT OPERATION 1-5-2 Status for percent key Ck Example Round Percent P3 appears in mode display Up %+ ZZ : Select a number from list A Select a number from list B k (To end the setting) 1-6 Taxable Status for minus key A Part-2 Selections Rounding of results produced by Percent Key operation. Round off (1.544=1.54; 1.545=1.55) ? Round up (1.544=1.55; 1.545=1.55) Z Cut off (1.544=1.54; 1.545=1.54) X Program Percent Key to register discounts (%–). ? Program Percent Key to register premiums (%+). Z B The minus key is initialized as Non-taxable. Z k~ P appears in mode display Example : Change minus key registrations Taxable status 1. .g Select key from list A Minus key k (To end the setting) Selections Taxable status 1 . Taxable status 2 ] Taxable status 3 u Taxable status 4 h All taxable status (1, 2, 3 and 4) Non-taxable status A .] m E 21 Part-2 CONVENIENT OPERATION 1-7 General features Mode Switch CAL X REG 1-7-1 To set general controls OFF Ck RF PGM P3 appears in mode display ?NXX k Program code No. Select a number from list A ???? p k (To end the setting) Select a number from list B Select a number from list C Select a number from list D Selections Limit the last 1 digit of total amount to 0 and 5 when Malaysian rounding is specified for subtotal and total amount. Time display format: No ? HH-MM Yes Z No V HH-MM SS Yes B A Selections Maintain key buffer during receipt issue in REG mode. Reset the transaction number to zero whenever a General Control Reset Report is issued. Allow credit balance registration. Yes ? Yes No Z No Yes X No No C Yes V Yes No B Yes Yes N No No M B E 22 Selections Limit the last 2 digits of cash amount tendered to 00 and 50 when Denmark rounding is specified for subtotal and total amount. Allow partial cash amount tendered. Allow partial check amount tendered. No ? Yes Yes Z Yes No X No Yes C No V Yes Yes B No No N No Yes M C Selections Use the ' key as a 000 key. Cashier assignment systems (sign on) is used. No Yes No Yes No Yes ? Z X C D Z Part-2 CONVENIENT OPERATION Ck 1-7-2 To set printing controls P3 appears in mode display ?BXX k Program code No. ???? p Select a number from list A k Select a number from list B (To end the setting) Select a number from list C Select a number from list D ? Use the printer to print receipts. Z Selections A Selections Print zero-total line on the General Control Read/Reset Reports Print Total line at finalization (only for Australia). No Yes Part-2 Selections Use the printer to print a journal. Print RF switch mode refund count/ amount on the General Control Read/ Reset Reports. Print the grand sales total on the General Control Reset Reports. Print the time on the receipt and journal. No Yes No Yes No ? Z V B Yes Yes B No No Yes Yes No Yes No Yes No Yes No ? Z X C V B N M C Selections Print the consecutive number on the receipt/journal. Print the subtotal on the receipt/ journal when the Subtotal Key is pressed. Skip item print on journal. No No Yes No Yes Yes Yes No Yes No Yes No Yes No ? Z X C V B N M D E 23 Part-2 CONVENIENT OPERATION 1-7-3 Printer switch for Receipt or Journal Mode Switch The printer is initialized as journal. CAL X REG Z OFF Example RF To print a receipt PGM Zk P appears in mode display Zu Select a number from list A k (To end the setting) Selections Use the printer to print a journal. ? Use the printer to print receipts. Z A • Printer selection to print a journal or receipts can also be set on procedures 1-7-2 “To set printing controls”. E 24 Part-2 CONVENIENT OPERATION 1-8 PLU setting 1-8-1 Linkage with Departments Ck P3 appears in mode display Example PLU No. Link dept. No. 1 4 100 4 ZiZ p PLU No. Select number from list A Z?? i PLU No. Vp Dept. No. to be linked k Part-2 (To end the setting) Selections ? Linked to dept. 20. Linked depts. 1~20 respectively. Z~ X? A • 120 PLUs can be set. • When the linked department is not specified, the PLU is linked to department 20. • Status for a single-item sale and tax status are followed the specified linked department. 1-8-2 Unit Prices for PLUs Example PLU No. Unit Price Zk P appears in mode display 1 2 $1.00 $3.00 Zi PLU No. Z?? p Unit Price Xi PLU No. C?? p Unit Price k (To end the setting) • Unit prices within the range of $0.01~999.99. E 25 Part-2 CONVENIENT OPERATION Ck 1-9 Setting the Tax Rate and rounding P3 appears in mode display ?ZXB k Program set code No. for tax rate 1*1 ??"???? p Enter tax rate A ???? p Select numbers from list B Select number from list D Select number from list C k *1 Program set code No. for Tax rate 2 is ?XXB Tax rate 3 is ?CXB Tax rate 4 is ?VXB. • You can use either an add-on rate tax or an add-in rate tax (VAT), depending on the requirements in your area. You can specify only one tax rate. • The normal rounding specification tells the cash register how to round tax amounts to the proper number of decimal places. • The special rounding specification and Danish rounding tell the cash register how to round off subtotals and totals so that their rightmost 2 digits are 00 and 50. • Note that the rounding specification you program for your cash register depends on the tax laws of your country. (To end the setting) Tax rate specifications The tax rate within the range of 0.0001 ~ 99.9999%. Use " key for decimal point. Normal rounding specifications Cut off to 2 decimal places. ?? (1.544=1.54; 1.545=1.54) Round off to 2 decimal places. B? (1.544=1.54; 1.545=1.55) Round up to 2 decimal places. >? (1.544=1.55; 1.545=1.55) A B Special rounding specifications for subtotal and total amounts No specifications Special rounding 1: 0 ~ 2 ➝ 0; 3 ~ 7 ➝ 5; 8 ~ 9 ➝ 10 Examples: 1.21=1.20; 1.26=1.25; 1.28=1.30 Special rounding 2: 0 ~ 4 ➝ 0; 5 ~ 9 ➝ 10 Examples: 1.123=1.120; 1.525=1.530 Danish rounding *1: 0 ~ 24 ➝ 0; 25 ~74 ➝ 50; 75 ~ 100 ➝ 100 ? Z X C (set the amount tender restriction on page 22 also) Examples: 1.11=1.00; 1.39=1.50;1.99=2.00 Malaysian rounding: 0 ~ 2 ➝ 0; 3 ~ 7 ➝ 5; 8 ~ 9 ➝ 10 B (set the amount tender restriction on page 22 also) Examples: 1.21=1.20; 1.26=1.25; 1.28=1.30 Scandinavian rounding: 0~ 24 ➝ 0; 25 ~ 74 ➝ 50; 75 ~ 99 ➝ 100 Examples: 1.21=1.0; 1.30=1.50; 1.87=2.00 Australian rounding (only for tax rate 1) 0 ~ 2 ➝ 0; 3 ~ 7 ➝ 5; 8 ~ 9 ➝ 10 Examples: 1.21=1.20; 1.26=1.25; 1.28=1.30 Czech rounding: 0 ~ 49 ➝ 00; 50 ~ 99 ➝ 100 Examples: 1.23=1.00; 1.52=2.00 Normal rounding specifications No specifications. ? Specifies add-on rate tax. X Specifies add-in rate tax (VAT). C C N M < D See page 19 (department key), 20 (percent key), 21 (minus key) to change the fixed tax status. *1: In case of defining Danish rounding, the Euro should be set to the sub currency and the local to the main currency. E 26 Part-2 CONVENIENT OPERATION 1-10 To control Tax Status printing Mode Switch CAL X REG Z OFF Ck RF PGM P3 appears in mode display ?CXN k Program set code No. ??? p Select number from list A Select number from list B Always “0” k Part-2 (To end the setting) Selections Print tax total line (only for Australia). Print tax symbol. Yes No No Yes No Yes ? Z X C A Selections Print taxable amount. Print taxable amount and tax amount for Add-in. Yes No Yes No Yes No ? Z X C B E 27 Part-2 CONVENIENT OPERATION 1-11 Printing to read All Preset Data • Printing preset data. 1-11-1 Printing preset data except PLU settings Printout Operation p 08-01-10 08-06#0038 01••••1•00 01-041 02••••2•20 — Date — Time/Consecutive No. X— Read Symbol — Dept No./Unit Price — Tax Status/Normal Dept/ Digit Limit/Single Item 02-051 20•••11•00 04-000 -•••••••01 — Minus/Tax Status 2•5 % — Percent Rate/%+ or %15-11 — Tax Status/Percent Key Control e1•23242 #— Euro Exchange Rate 0122•••#22 — Date/Monetary Mode Control 0222•#0000 0522•#0062 0622•#0000 1022••••#3 — Print Control — General Control — Calculation Control — Tax Control — Euro Status 0326••#002 2422••••#0 0125•••••• 5•2500 % — 5003 — 0000 0225•••••• 10•0000 % — Tax Rate1 Rounding specification/ Tax System specification Tax Rate 2 5003 0000 0425•••••• 25•0000 % — Tax Rate 4 Tax Status Printout 00 01 02 03 04 15 E 28 Meaning Non taxable Taxable 1 Taxable 2 Taxable 3 Taxable 4 All taxable 5003 0000 08-01-10 Part-2 CONVENIENT OPERATION Mode Switch CAL X REG Z OFF RF PGM 1-11-2 Printing preset PLU settings Operation Zp Printout 08-01-10 08-10#0039 01 Part-2 001•••1•00 — Date — Time/Consecutive No. X — Read symbol — PLU No./Unit Price — Linked department 002•••2•20 02 003•••3•00 03 004•••4•00 04 100••10•00 20 08-01-10 E 29 Part-2 CONVENIENT OPERATION 2. Various Operations Mode Switch REG 2-1 Registration using preset price for Departments. CAL X Z OFF RF PGM (Programming: See page 19) Operation Printout Example Unit Price $1.00 $2.20 $11.00 Quantity 1 2 4 Depts. 1 2 3 Amount $50.00 tendered G S S V hD k B???p 01••••1•00 02••••2•20 02••••2•20 4 •11•00 03•••44•00 — Dept.1 Unit Price — Dept.2 Unit Price — Repeat X — Multiplication Symbol @ — Dept.3 Unit Price •49•40 S •50•00 C •0•60 G — Cash Amount Tendered — Change 2-2 Single-Item Sales (Programming: See page 20) B? G Example 1: Status Single item sale Unit Price $0.50 Quantitiy 1 Dept. 1 Example 2: Status Unit Price Quantitiy Dept. Normal $1.00 1 2 01••••0•50 •0•50 C — Cash Sales For this example, Dept. 1 is programmed for a single-item-sale. Z?? S B? G k p Single item sale $0.50 1 1 02••••1•00 01••••0•50 •1•50 C — Cash Sales Single-item sale cannot be finalized if an item is registered previously. E 30 Part-2 CONVENIENT OPERATION 2-3 Check sales Example Unit Price Quantity Depts. $35.00 2 4 Operation CB?? F F k m Printout 04•••35•00 04•••35•00 •70•00 K — Check Sales 2-4 Split cash/ check sales Example C???S XB??D k X???p m 02•••30•00 03•••25•00 Part-2 Unit Price $30.00 $25.00 Quantity 1 1 Depts. 2 3 Cash amount $20.00 tendered Check $35.00 •55•00 S •20•00 C •35•00 K Mode Switch CAL X REG Z OFF RF PGM 2-5 Refund Example Unit Price $1.00 $2.00 Quantity 1 1 Depts. 2 3 Operation Z?? S X?? D k p Printout 13-55#0074 r 02••••1•00 03••••2•00 •3•00 C — Refund Mode Indicator After you finish RF mode operation, be sure to return the Mode Switch to the REG (register) setting. E 31 Part-2 CONVENIENT OPERATION 2-6 PLU operation Mode Switch REG CAL X Z OFF RF PGM 2-6-1 PLU registration Operation Zi i Vh Xi p (Programming: See page 25) Example PLU No. 1 2 Unit Price $1.00 $2.00 Quantity 2 4 Depts. 1 1 Cash amount $10.00 tendered 2-6-2 PLU Single-Item Sale Operation (Programming: See page 25) Zi Printout PLU No. 001•••1•00 001•••1•00 — Repeat X — Multiplication Symbol 4 •2•00 @ — Preset Unit Price 002•••8•00 •10•00 C — Cash Amount Tendered Printout 001•••1•00 •1•00 C Example PLU No. Status Unit Price Quantity 1 Single item sale $1.00 1 • For this example, linked department 1 is programmed for a singleitem-sale. • Single-item sale cannot be finalized if an item is registered previously. 2-6-3 PLU report Operation Printout Mode Switch CAL REG XZ OFF ?Z p (Read) RF PGM Mode Switch CAL X REG RF PGM 32 ?Z p (Reset ) OFF E Z 08-01-10 18-16#0238 #01#0001 001•••••12 •12•00 002•••••27 •27•00 100•••••10 •180•00 1284 •10856•89 Z — Reset Counter — PLU No./No. of items — Amount — PLU total count — PLU total amount Part-2 CONVENIENT OPERATION 2-7 Other registrations Mode Switch REG CAL X Z OFF RF PGM 2-7-1 Reading the Time and Date Display Operation h 13-5# Hour/Minute 08-01-10 y ~00 Day/Month/Year Part-2 h • Flashes per second • If you have changed the date order (refer to page 9), enter date of that order. Mode Switch CAL X REG Z OFF RF Adjusting the Time Display Operation PGM • Turn the Mode Switch to PGM. Example Zk Current time = 13:58 ZCB<h Current Time: Hour Minute p ~00 13-58 02 ~00 y • Enter current time in 24 hour system. Mode Switch CAL X REG Z OFF RF Adjusting the Date Display Operation PGM • Turn the Mode Switch to PGM. Example Zk Current date = 8, January 2010 ?<?ZZ?h Current date: Day Month Year y p ~00 08-01-10 ~00 • Enter current date in 6 digits. • Enter the last 2 digits for year set. (2010 → 10) E 33 Part-2 CONVENIENT OPERATION Mode Switch REG CAL X Z OFF RF PGM 2-7-2 Paid out from cash in drawer Operation 12345678 j Enter reference No. Z??? ] 2-7-3 Cash received on account 2-7-4 Registering identification numbers Operation N?? . Operation Example: Amount due reduced by $0.50. E 34 #12345678 08-01-10 13-57#0060 •10•00 P — Reference Number — Paid Out Amount Printout •6•00 R — Received On Account Amount Printout A reference number or ID number of up to 8 digits can be registered prior to any transaction. ZXCV BNM< j B? G p 2-7-5 Reduction on subtotal Printout Operation Z?? G X?? F k B? g p #12345678 08-01-10 13-59#0062 01••••0•50 •0•50 C Printout 01••••1•00 04••••2•00 -0•50 •2•50 C — Reference Number or ID No. Part-2 CONVENIENT OPERATION 2-7-6 Premium/ Discount Operation Printout Premium Z?? G : •2.5% premium/discount (programmed to x key) X?? S applied to first item. C?? G k M: • 7% premium/discount applied to transaction total. p •For programming the x key as percent minus or percent plus, see page 21. •For programming percent rate, see page 20. Discount 01••••1•00 01••••1•00 2•5 % — *1 — *2 •0•03 02••••2•00 2•5 %- — *1 -0•03 — *2 02••••2•00 01••••3•00 01••••3•00 •6•03 S — *3 7 % — *4 — *5 •0•42 •5•97 S — *3 7 %- — *4 -0•42 — *5 •6•45 C •5•55 C 2-8 Cashier Assignment Part-2 *1 Premium/Discount Rate *2 Premium/Discount Amount *3 Subtotal *4 Premium/Discount Rate *5 Premium/Discount Amount Mode Switch In any mode REG, RF, CAL, X or Z, (Programming: See page 22) except PGM Cashier assignment system is used to control each cashier (or clerk) sales total. When you select this function on page 22, you can get 8 cashiers (or clerk) sales data. Cashier assignment must be performed prior to starting registration or any other operation, except Program mode. Z: Select a number from list A Selections Sign off (cancel) the assignment of cashier ID No. ? Assign a cashier ID No. 1 through 8. Z ~ < A • Currently assigned cashier (or clerk) ID number is printed on the receipt or journal for each transaction. • The assigned clerk memory number is automatically signed off when the mode key is set to OFF position. • The assigned cashier (or clerk) sales totals with ID number are printed on the receipt or journal when you perform daily X/Z sales report. E 35 Part 3 CALCULATOR FUNCTION While registering at REG mode, you can switch to CAL mode and then return to REG mode to resume the registration. 1. Calculator Mode Mode Switch Mode Switch REG CAL CAL X Z OFF Z OFF RF RF PGM PGM Display Operation 1-1 Calculation examples X REG t BHZ t ç ~ (Miss operation) (Cancels item entered.) 5+3–2= (23–56)×78= (4×3–6)÷3.5+8= 12% on 1500 BHCJX p & XCJBNKM< p -257$ VKCJNLC"BH< p )7142857 1-2 Memory recall ZB??KZX : Recalls the current amount onto the display. – during registration: current subtotal – registration has been completed: the last amount Display Operation On REG mode Z?'GX?'S /LCp On CAL mode Example: Divide the current subtotal $30.00 at REG mode by 3 (to divide the bill between 3 people). Memory recall On REG mode Example: Recall the current result at CAL mode during registration, and register the cash amount due for each person. 36 1~ Recalls the current result by pressing p key at CAL mode on the display. Printout Operation E 18~ /p /p /p Memory recall 01•••10•00 02•••20•00 •30•00 •10•00 •10•00 •10•00 S C C C •0•00 G Part-3 CALCULATOR FUNCTION 1-3 Setting for calculator operation Mode Switch CAL X REG Z OFF RF PGM C k P3 appears in mode display Z?XX k Program Code No. ? p Select a number from list A. k (To end the setting) Part-3 Selections Open drawer whenever p is pressed.* Open drawer whenever m is pressed.* Print No. of Equal key operations on General Control X and Z reports. No Yes No Yes Yes No No Yes No Yes Yes No Yes No ? Z X C V B N M A * Drawer does not open during registration procedures even if you press p or m by turning the mode switch to CAL position. E 37 Part 4 USEFUL INFORMATION 1. Troubleshooting Symptom/Problem 1 E01 appears on the display. 2 E08 appears on the display. 3 E94 appears on the display. 4 5 6 7 8 No date on receipt. Paper is not advancing enough. Drawer opens up after ringing up only one time. Not clearing totals at end of day after taking report. Programming is lost whenever register is unplugged or there is a power outage. Register is inoperative. Can’t get money out of drawer. 9 E90 appears on the display. 2. Most common causes Solutions Changing modes without complet- Return mode switch to where it stops buzzing transaction. ing and press p. Prior to starting registration of any other Sign on operation is not performed. operation, press Z~< and then :. Remove jammed paper. Turn Mode switch Printer paper is jammed. to OFF then turn to ON, or Turn power OFF and then turn power ON. Printer is programmed as a journal. Program printer to print receipts. Department is programmed as a single item dept. Program the dept. as a normal dept. Using X mode to take out reports. Use Z mode to take out reports. Bad or no batteries. Put in new batteries. No power. Pull lever underneath register at rear. Totals remain in the memory. Issue the general control reset report, periodic reset report and PLU reset report. Specifications INPUT METHOD Entry: 10-key system; Buffer memory 8 keys (2-key roll over) Display (LED): Amount 8 digits (zero suppression); Department/PLU No.; No. of repeats PRINTER Journal: 12 digits (Amount 10 digits, Symbol 2 digits) (or receipt) Automatic paper roll winding (journal) Paper roll: 58 mm × 80 mm ∅ (Max.) CALCULATIONS Entry 8 digits; Registration 7 digits; Total 8 digits CALCULATOR FUNCTION 8 digits; Arithmetic calculations; Percent calculations Memory protection batteries: The effective service life of the memory protection batteries 3 (UM-3, or R6P (SUM-3) type batteries) is approximately one year from installation into the machine. Power source/Power consumption: See the rating plate. Operating temperature: 0°C to 40°C (32°F to 104°F) Humidity: 10 to 90% Dimensions/Weight: 188 mm(H)× 330 mm(W)× 360 mm(D) with S drawer 4 kg with S drawer 205 mm(H)× 410 mm(W)× 450 mm(D) with M drawer 8 kg with M drawer Specifications and design are subject to change without notice. E 38 When the cash drawer does not open! In case of power failure or the machine is in malfunction, the cash drawer does not open automatically. Even in these cases, you can open the cash drawer by pulling drawer release lever (see below). Important! The drawer will not open, if it is locked with a drawer lock key. ◗ To replace the ink roll ! Turn to the OFF mode and remove the Mode Switch CAL X REG Z Part-4 printer cover. @ Lift up the tab on the ink roll marked “PULL UP”. # Install a new Ink Roll and press it down firmly but gently until it snaps into place. $ Replace the printer cover onto the cash register. % Turn to the REG mode, and press the m key to check for correct operation. OFF RF PGM Laite on liitettävä suojamaadoituskostkettimilla vaurstettuun pistrasiaan Apparatet må tiloples jordet dtikkontakt Apparaten skall anslutas till jordat nätuttag This mark applies in EU countries only. Manufacturer: CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku Tokyo 151-8543, Japan Representative within the European Union: Casio Europe GmbH Casio-Platz 1, 22848 Norderstedt Germany Please keep all information for future reference. E 39 c CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan MA0812-A 140CR*E Printed in Indonesia Printed on recycled paper.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project