Alcatel | Speed Touch PC | Installation guide | Alcatel Speed Touch PC Installation guide

Alcatel Speed Touch PC Installation guide
READ ME FIRST
Windows® NT
®
*DSL Equipment Installation Guide:
Alcatel Speed Touch PC®
*Digital Subscriber Line
Part Number: AlcatelPCNT02A
Version 1.2-A
©2001 SBC Advanced Solutions, Inc. All rights reserved.
Table of Contents
Follow Steps 1 through 7 to complete the DSL Equipment Installation
Step 1: Verify Your System Requirements and Documents
Step 2: Verify the Contents of Your DSL Equipment Kit
Step 3: Install a Telephone Filter on Every Telephone Line
Step 4: Choose Your Modem and Check Your Minimum Requirements
Step 5: Installing the Alcatel Speed Touch PC® Software and Hardware
Step 6: Finish Configuring your System
Step 7: Create a Connection Profile
2
3
4
8
12
19
22
APPENDICES
Having Trouble?
Uninstalling/Reinstalling the Alcatel Speed Touch PC® Adapter
Adding TCP/IP to Windows NT
Troubleshooting SBC Express
Modem Diagnostic Lights
For Support:
24
25
26
27
30
32
•
•
Review the troubleshooting section in this guide on page 25
Call your Internet Service Provider 'help desk' for further information on Internet Service
Provider connection, and registration.
IMPORTANT NOTE: This guide portrays the typical flow for the installation process.
Please follow the instructions, including running the SBC Express software BEFORE
installing any NIC cards or modems. Some computer or network configurations may cause
software windows to appear that are not depicted in this guide. Please read and follow the
instructions on those screens to continue the installation process.
Verify that you are installing your DSL equipment AFTER the “Service Completion Date”
given to you when you ordered your DSL Internet Service.
SBC Advanced Solutions, Inc. and affiliates have no responsibility for any personal injury
or property damage which may result from your installation of DSL Equipment as
discussed in this Guide. SBC Advanced Solutions, Inc. and its affiliates specifically
disclaim any liability for such injury or damage. By proceeding with this installation, you
assume all risk of personal injury or property damage. Please consult the documentation
provided by your PC vendor to identify any impacts to your warranty. SBC, SBC
EXPRESS and the SBC Logo are registered trademarks of SBC Communications, Inc.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 1
Step 1: Verify Your System Requirements and Documents
This Installation Guide is for Windows® NT users only.
The SBC Express software will ensure that you meet the following minimum requirements.
You will not be able to complete the installation without meeting these requirements.
•
PC with a Pentium-class processor, CD-ROM Drive, 133 MHz, 25 Mb free disk space,
32 Mb RAM and An available PCI slot
Other items you may need during the installation process:
•
•
Your system manufacturer Owner’s Manual.
Documentation and/or software from your Internet Service Provider.
Call your Internet Service Provider if you have questions regarding System Requirements
or System Documentation.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 2
Step 2: Verify the Contents of Your DSL Equipment Kit
Your DSL Equipment Kit Contains:
A: This Installation Guide and the SBC Express CD.
B: 1 Alcatel Speed Touch PC® Internal Modem
C: 1 Filter Pack containing: 5 in-line filters, 1 wall-mount filter, 1 two-way adapter, and 1 data cable.
Note: Internet Software and/or instructions may be provided separately by your Internet Service
Provider.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 3
Step 3:
3-1
Install a Telephone Filter on Every Telephone Line
Determine how many telephone jacks in your home share the same telephone number
with the activated DSL.
1) Locate the phone
jack where you want
to connect your DSL
2) Insert the 2-way
adapter in the phone
jack
3) Connect a filter to
one side of the 2-way
adapter
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 4
4) If you have a
phone, fax machine,
analog modem or
other phone device at
this location, connect
it to the filter
5) Connect the data
cable that will go to
your DSL modem to
the unfiltered side of
the 2-way adapter
To the DSL modem
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 5
3-2
Install a filter on all other phones and phone devices
Why do I need a filter on all my other phones and phone devices?
Converting your regular phone line into a high-speed Digital Subscriber Line (DSL) can
cause audible noise (high pitched tones and static) when you talk on the phone. You
need to install a filter on every telephone or device that shares the same phone number as
your DSL line to eliminate this noise.
Other phones
filter
Analog computer modems
Answering machines
Caller ID boxes
filter
filter
Wall mount phones
Fax machines
Use the wall mount filter shown
Wall mount filter
filter
filter
Remember! Don’t install a filter on the data cable that you are
connecting to your DSL modem.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 6
3-3
Other filters you may encounter in your DSL Equipment Kit.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 7
Step 4:
Choose Your Modem and Minimum Requirements Check
4-1
Insert the SBC Express CD into your CD-ROM drive. SBC Express should start
automatically. If not, select Run from the Windows Start menu. Type “D:\Launch.exe”.
(Substitute the appropriate letter of your CD-ROM drive for “D”.)
4-2
Select Alcatel Speed Touch PC and click Next.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 8
4-3
SBC Express displays the Welcome screen. Click Next to proceed.
4-4
SBC Express displays the license agreement. If you agree to the terms, click Accept. If
you do not accept, installation cannot continue.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 9
4-5
SBC Express now prompts you for your first and last name. Please type your first and last
name and then click Next to proceed. Do not enter Technician Name.
4-6
Enter your 10-digit DSL phone number in the next screen. Click Next to proceed.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 10
4-7
SBC Express quickly checks your computer system to ensure that it meets the minimum
requirements for DSL service.
4-8
SBC Express has determined that you need to install the Alcatel Speed Touch PC. Click
Shutdown and proceed to step 5 to install the Alcatel Speed Touch PC.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 11
Step 5:
Installing the Alcatel Speed Touch PC
If you shutdown your computer, leave the CD in the the CDROM
drive, and SBC Express will continue after you restart.
You should be at the following screen in the SBC Express Software:
5-1
Click Shutdown in SBC Express and then turn off all peripheral devices.
Remember to leave the SBC Express CD in the CD-ROM drive.
5-2
Unplug the power cord for your computer from the electrical outlet.
5-3
Open the case of your computer (review your computer manufacturer’s Owner’s Manual
for specific instructions).
5-4
Touch the computer chassis (metal frame) before touching the Alcatel Speed Touch PC
adapter. This helps to protect the Alcatel DLS Modem from static electricity.
5-5
Locate an available PCI slot (usually white in color). You may use any available PCI
slot. Make sure you are looking downwards on the PCI slot. You may need to turn the
computer on its side to accomplish this (review your computer manufacturer’s Owner’s
Manual for specific instructions).
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 12
5-6
Remove the metal PCI slot cover from the unused PCI slot, and retain the screw.
PCI Slot
Remove PCI slot
cover
5-7
Carefully insert the Alcatel Speed Touch PC adpter into any empty PCI slot. Make sure
the card is completely seated by pressing firmly.
5-8
Verify that the end bracket is flush against the chassis. Make sure the gold connectors
along the base of the Alcatel Speed Touch PC adapter are completely and evenly inserted
into the PCI slot.
5-9
Fasten the card into the computer chassis with the screw you set aside earlier.
5-10
Replace the computer cover. Plug the power cord back into the electrical outlet, making
sure the SBC Express CD is in the CD-ROM drive.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 13
Installing the Alcatel Speed Touch PC® Software
5-11
•
5-12
Turn on your computer.
NOTE: Windows NT will NOT automatically detect your Alcatel Speed Touch PC®
adapter. SBC Express will display the screen below. Please IGNORE this screen and
proceed to step 5-12. Do NOT Cancel SBC Express.
Right click on the Network Neighborhood icon and select Properties.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 14
5-13
Click on the Adapters tab.
5-14
Click on the Add button.
5-15 Click on the Have Disk button.
5-16 The SBC Express has copied all the necessary files to “C:\Temp”. At this prompt please
type in C:\Temp and click OK.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 15
5-17
Windows NT will presents the following select OEM option screen, select ITeX ADSL
PCI NIC and click OK. (Note: The IteX ADSL PCI NIC is the Alcatel Speed Touch PC
adapter. This is the formal adapter name used for NT)
5-18
After you install the driver software, the ITeX ADSL PCI NIC will appear under Network
Adapters. Click Close.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 16
5-19
You will be prompted to bind a TCIP/IP address to the Adapter. Select the ITeX ADSL
PCI NIC in the drop down box in the Microsoft TCP/IP Properties window shown
below. Next, click “Obtain an IP address from a DHCP server.” This selection will
cause the Microsoft TCP/IP window (also shown below) to appear. Click Yes to this
screen and then OK on the Microsoft TCP/IP Properties window.
5-20
You will be prompted to reboot the system. This may take several ( 3-5 ) minutes as
network settings are established. BE SURE TO LEAVE SBC EXPRESS CD IN CDROM DRIVE. Click Yes.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 17
5-21
SBC Express will re-run the Minimum Requirements test and detect the newly installed
Alcatel Speed Touch PC adapter and complete, stopping at the following screen. If
problems are detected follow the instructions on the screen or look at the troubleshooting
section of this manual for further information. Follow the instructions in Step 6
beginning on the next page before continuing.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 18
Step 6:
Finish Configuring Your System
6-1
If the Alcatel Speed Touch PC card is installed properly, you will see the following
screen. You must now connect the Alcatel Speed Touch PC to the phone jack prepared in
Step 3.
6-2
Connect the Alcatel Speed Touch ADSL modem, see diagram below.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 19
6-3
To determine if your DSL modem has made a good connection look at the icon in the
system tray. If both lights are black then you have a good connection. If either light is
red or there is a red circle with a slash through it then check the diagnostic guide in
appendix E for help.
6-4
SBC Express will install additional software necessary for your service. Leave the SBC
Express CD in the CD-ROM drive. You will see the following screen during the
software installation. Your machine may reboot during this process.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 20
6-5
You have finished software installation for DSL. Click Finished in SBC Express window
and then proceed to Step 7 to configure the connection to your Internet Service Provider.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 21
Step 7: Create a Connection Profile
7-1
Setup a New Profile in EnterNet 300.
• Double-click on the desktop EnterNet 300 icon.
In Profiles, double-click on the Create New Profile icon.
•
7-2 You will be prompted to supply a name for the connection. Enter the Profile Name as DSL
Connection. Click Next.
7-3 Locate your ISP provided User ID and Password. Set up the DSL Connection profile by
typing the User ID and Password in the User Name and Password fields. Click Next.
7-4 Leave the Server and Service fields BLANK. Click Next.
7-5
Click Finish to save the configuration.
7-6 Double-click the new DSL Connection icon in the Profiles Dialog box.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 22
7-7
A Connection dialog will open. Click Connect.
7-8
Double-click on the EnterNet icon in the system tray (next to the clock, in the lower-right
corner of your screen) and select Disconnect.
EnterNet Icon
7-9
Double-click the EnterNet 300 folder on your desktop and then double-click DSL
Connection icon.
7-10
Open your browser again and test your connection by visiting your favorite web sites.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 23
Appendices
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 24
APPENDIX A
Having Trouble?
If the suggestions below don’t resolve your problem, technical support is available from your
Internet Service Provider. Please refer to the Internet Service Provider's information on how to
contact them for technical assistance.
I can’t open my computer case. What do I do?
•
Consult your computer manufacturer’s Owner’s Manual.
•
Call your computer manufacturer’s Support Line.
I can’t connect. What do I do?
•
Make sure there is no filter on the phone jack/cord connected to your DSL modem
•
Check your Ethernet cable connection. Is it secure?
•
Verify that you are installing your DSL equipment AFTER the “Service Completion Date”
given to you when you ordered your DSL Internet Service.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 25
APPENDIX B
Uninstall/reinstall the Alcatel Speed Touch PC® Adapter
Uninstalling (and reinstalling) the Alcatel Speed Touch PC® adapter in Windows®
NT
1. Select Start -> Settings -> Control Panel. Double-click the Network icon and choose the
Adapters tab.
2. Highlight the Alcatel Speed Touch PC® Adapter and click the Remove button.
3. Click ‘Yes’ to remove the component from the system when prompted.
4. Click the Close button to close the Adapters window.
5. Shut down the desktop or laptop. Turn OFF and unplug the computer and any peripheral
devices.
6. Remove the Alcatel Speed Touch PC® Adapter Card.
•
Open the computer case using your computer manufacturer’s instructions and then,
remove the screw holding card in place.
•
Carefully remove the Alcatel Speed Touch PC® Adapter card from the PCI slot.
7. Reinstall the card following procedures in Step 5.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 26
APPENDIX C
Adding TCP\IP to Windows NT
Right click on the network neighborhood icon and select properties.
2. Click on the ‘Protocols’ tab and click ‘Add’.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 27
3. Select the ‘TCP/IP Protocol’ and click ‘OK.’
4. Specify the path of your NT installation files or insert the Windows NT CD-ROM and
specify the I386 folder.
5. Select “No” when NT asks ‘Do you wish to use DHCP?’.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 28
6. After clicking “No”, TCP/IP should appear under the protocols tab.
7. Click “Close” to bind all the information. You must restart your computer for the settings
to be stored.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 29
APPENDIX D
Troubleshooting SBC Express
Please refer to this list if you are having problems using SBC Express or if you receive an error
message. If after troubleshooting, you are still having problems, then you should contact your
Internet Service Provider for assistance.
Step
Problem
Solution
Launch
The following dialog appears:
Reset your display to 256 colors or more. SBC
Express will not run in 16 color mode.
From the start menu, choose “settings->control
panel”. Double-click “Display” and choose the
“settings” tab. Select more colors from the
“colors” pull-down list.
Minimum
Resources
SBC Express verifies minimum requirements on
several resources including hard drive space, RAM,
operating system level, and processor speed and
family.
Update your computer to the recommended
resource level.
If any of these resources are under the required value,
an error will display describing which resource did not
meet the requirement.
Installing
Network
Interface Card
When installing Network Interface Cards on Windows
systems the installation process may ask for the
original installation disk.
Some of these files can be found in the SYSTEM
directory or the WINDOWS directory of the
machine. If not, you will have to provide an
installation CD-ROM for the installation of the
drivers to be successful.
Incompatible
Adapter
This scenario can occur when a machine had a
previous NIC or Network Adapter installed, but the
physical device is missing or was misconfigured.
Use the “Fix” button to launch the appropriate
system control panel along with context sensitive
help. The help provided will guide you through
the steps to disable or remove the adapter.
Missing Internet
Protocol
This scenario can occur if Client for Microsoft
Networks is not installed with the TCP/IP protocol or
if the NIC is installed without binding TCP/IP to the
NIC.
Use the “Fix” button to launch the appropriate
control panel and context sensitive help to guide
you in binding TCP/IP to the network adapter.
Disabled
Network Adapter
This scenario can occur when a NIC is present in the
system, yet the adapter has been disabled.
Use the “Fix” button with context sensitive help
to guide you through enabling the adapter.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 30
Unknown
Network
Interface
Adapter
This scenario can occur if a NIC is physically present and
detected by Plug-n-Play, but no drivers were installed for the
NIC. Windows will add this device to the “Other Devices”
section in the Device Manager.
Use the “Fix” button to launch the appropriate
control panel and context sensitive help to
guide you through removing the “Unknown
device”.
Ping Test
The Ping Test is usually accomplished within the Configure
TCP/IP step, where SBC Express pings the default gateway.
An explicit IP address can also be used.
Failure during this test can occur from invalid
network settings, the Ethernet cable not being
plugged in, the DSL modem not being in
synch, or if the specified IP address does not
allow a ping.
Make sure your Ethernet cable is plugged in
and powercycle your DSL modem. Use the
“Retry” button to try the test again.
DNS Test
The DNS Test will determine the currently defined DNS
servers, attempt to ping them, and upon a successful ping,
will resolve a specified hostname to an IP address.
This test can fail if the DNS server is invalid.
If you entered static IP information, ensure you
entered the DNS servers correctly.
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 31
APPENDIX E
Modem Diagnostic Lights
To help identify a problem with the modem connection please look at the icon on located in the
system tray as seen below.
By comparing the lights to the table below you should be able to determine the problem.
Diagnostic Icon
Red, Red
No ADSL connection or handshaking. Check your cable.
Black, Yellow
Handshaking (flashing yellow alternating position).
Black, Black
No data traffic or idle connection.
Black, Green
Modem is receiving data.
Green, Black
Modem is transmitting data.
Green, Green
Modem is receiving and transmitting data
Red Circle With Slash
ADSL modem is either disconnected or a driver installation problem exists
This concludes the DSL Equipment Installation Guide
Installation Guide for Customer Self-Install: Alcatel Speed Touch PC®, Windows NT
©2001 SBC Advanced Solutions, Inc. All rights reserved
Page 32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising