EchoStar | AD-3000 IP Viaccess | User manual | EchoStar AD-3000 IP Viaccess User manual

EchoStar AD-3000 IP Viaccess User manual
User Manual
ANALOG/DIGITAL, POSTIONER RECEIVER WITH
EMBEDDED VIACCESS AND COMMON INTERFACE
CONTENTS
1. Safety instructions ------------------------------------------------------------------- 2
2.
Features ------------------------------------------------------------------------------- 3
3.
Front & rear view ------------------------------------------------------------------- 5
4. Remote Control Unit (RCU) ------------------------------------------------------- 7
5. Getting started ------------------------------------------------------------------------ 8
6.
How to connect your dish to the EchoStar AD-3000IP VIACCESS ----- 11
7.
Operation and menu program --------------------------------------------------- 13
A. Receiver and TV set-up ------------ ------------------------------------------- 13
B. Main menu & Installation ---------------------------------------------------- 19
C. Advanced Installation --------------------------------------------------------- 26
8. Specifications ------------------------------------------------------------------------- 28
Appendix.
Tri control database remote ----------------------------------------- 31
Trade Mark of the DVB Digital Video Broadcasting Project (1970)
1
1. Safety Instructions
WARNING!
Always follow these instructions to avoid the risk of injury to yourself or damage to your equipment.
Unplug the receiver from the AC power outlet before cleaning. Use only a damp cloth for cleaning
the exterior of the receiver.
Do not use accessories or attachments not recommended by the receiver manufacturer, as they may
cause hazards and will void the warranty.
Do not operate the receiver in high-humidity areas, or expose it to water or moisture.
Do not place the receiver on an unstable cart, stand, tripod, bracket, or table. The receiver may fall,
causing serious personal injury and damage to the receiver.
Do not block or cover slots and openings in the receiver. These are provided for ventilation and
protection from overheating. Never place the receiver near or over a radiator or heat register. Do
not place the receiver in an enclosure such as a cabinet without proper ventilation.
Do not stack the receiver on top of or below other electronic devices.
Operate the receiver using only the type of power source indicated on the marking label. Unplug the
receiver power cord by gripping the power plug, not the cord.
Route power supply cords so that they are not likely to be walked on or pinched by items placed upon
or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the unit.
Use an outlet that contains surge suppression or ground fault protection. For added protection during
a lightning storm, or when the receiver is left unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the lines between the receiver and the antenna. This will
provide some protection against damage caused by lightning or power line surges.
Do not attempt to service the receiver yourself, as opening or removing covers may expose you to
dangerous voltage, and will void the warranty. Refer all servicing to authorized service personnel.
Unplug the receiver from the wall outlet and refer servicing to authorized service personnel whenever
the following occurs:
The power supply cord or plug is damaged;
Liquid has been spilled, or objects have fallen into the receiver;
The receiver has been exposed to rain or water;
The receiver has been dropped or the chassis has been damaged;
The receiver exhibits a distinct change in performance.
2
2. Features
Common Section
1. Satellites : up to 50 satellites, 999 transponders
2. 4-digit 7-segment LED on the front panel displays channel information
3. Displays local time on the front panel in stand-by mode
4. Proprietary EchoStar OSG menu
5. 64-step volume control
6. VCR timer function (position, Digital/Analog, channel, start time, stop time)
7. Power recovery function
8. Last channel memory function
9. Favorite channel function (mixed Digital & Analog)
10. C/Ku control function
11. Parental lock / Installation & Edit lock / Receiver lock
12. Variety of LNB polarity control; 13/18V, 0/22kHz tone, 0/12V,
Mechanical polarizer, magnetic polarizer (Ferrite) and DiSEqC 1.0 TM
13. RS232C port for additional information service and update of the receiver control software
14. DiSEqC 1.0 TM compatible
15. Mechanical and magnetic polarizer control for each satellite
16. Auto Sat position search
17. Channel storing for multi satellites
18. Built-in positioner (high power azimuth control (36Vdc, 5A ))
3
Digital Section
1. MPEG-2 Video (MP@ML)
2. MPEG-1 Audio layer 1, layer 2
3. MPEG-2 Digital & fully DVB compliant
4. Viaccess embedded with 1 smart card
5. Capable of interfacing with the CAMs of DVB Common Interface standard
6. Capable of scanning the frequency for SMATV system
7. On-screen display with 256-color full resolution
8. Plug & Play installing program set-up
9. LD quality video, CD quality audio
10. RS232C port for additional information service and update of the receiver control software
11. Displays signal level to set up the satellite antenna with ease
12. Powerful editing facilities;
; PIDs, TV or Radio channel, channel name, satellite name, transponder name
13. Teletext function (Your TV should support teletext.) & Subtitling
14. SCPC/MCPC receivable from C/Ku-band satellites
15. Variable aspect ratio (4:3, 16:9) with pan vector
16. EPG for on-screen channel information
17. Multi-lingual function when provided by the satellite and broadcasting service provider
18. Total 5000 channels programmable (4000 Channels for TV & 1000 Channels for Radio)
19. S/PDIF(Sony/Philips Digital Interface) for the digital audio
Analog Section
1.
2.
3.
4.
5.
6.
7.
8.
700 programmable channels
1 IF input (900-2150MHz) / 1 bandwidth (27MHz)
32-step low threshold extension (3dB)
Audio mono / stereo selectable
C/ Ku band (invert/ normal video format) selectable
4 video level control
4 decoder modes
Color GUI (Graphic User Interface) menu
(overlaid with digital graphic OSG menu and analog background live picture)
9. Powerful editing facilities; channel name, satellite name
4
3. Front & Rear View
Front
Front Panel
Panel
Channel up / down
Selection / conf
irmation
Volume up / down
ON/Standby
1 Smart card slot
2 Slots for CI module
Rear
Rear Panel
Panel
LNB input
Antenna input
Loop through
RF output connector to TV
AC power cord
Note:
Note: All
Allthe
thecables
cablesused
usedfor
forInput/Output
Input/Outputconnection
connectionfor
forthe
thereceiver
receivershould
shouldbe
bewell
wellshielded.
shielded.
5
Smart Card and CI Module
To watch payable program channels, a CI module and a smart card from the service provider is necessary.
(The service provider is the distributor of the programs). CI modules and smart cards are only licensed to
service providers only and they are distributed by their dealers or agents.
If you are subscribed to the services of more than one service provider, you might have to insert or change
proper smart card and proper CI module of your choice.
Without CI module and smart card,only FTA (free-to-air) programs are available to watch.
Note : 1) The main plug must not be plugged in before inserting the CI module.
2) Insert the CI module fully into the slot behind the lid in the front panel of the receiver,
towards the arrow on the module facing upwards and inwards.
3) Insert your smart card fully into the slot on the CI module towards the arrow on the card facing
upwards and inwards.
4) CI module and smart card may give special menus which are not described in this manual.
5) A smart card is connected to a single service provider and to a specific range of channels.
6
4. Remote Control Unit (RCU)
The Power key turns the receiver on and off.
The LED (Light Emitting Diode) flashes red to show the remote is working.
The TV, VCR and SAT keys select the device to be controlled.
Pressing the SAT key allows the remote to control the functions
of the receiver.
The Volume and Channel keys control the two most
frequently used functions of the receiver.
The Mute key switches the sound on and off.
Number / Input keys enable direct channel selection command
selection using numeric keys.
The TV/RAD(Radio) key switches between TV and radio mode.
The FAV key shows a list of your selected favorite channels (To
define channels as favorite select the “Edit TV channel” menu).
The MENU key is used to see main menu or to return to previous
menu.
The cursor keys are for channel ?and ? and volume ? and ? .
The OK key is used to select a program, a highlighted line or
parameter value. Also you can see TV/Radio channel list while
watching TV or listening to the radio.
The EXIT key exits to the video viewing mode at any time.
The EPG key shows program information of the selected channel.
(EPG; Electronic Program Guide)
The Information key provides additional information about the
current channel and program (only available when provided by
the broadcaster). In the menus pressing this key provides up to
four lines of help.
The Subtitle key enables subtitling (only when provided by the broadcaster).
Selects the Audio Language or Soundtrack from among the data transmitted for the current
channel.
VIEW
Shows a thumb nail representation of the current channel in the “Edit TV Channel”,
“Parental Lock” and “EPG”.
The SAT key shows a list of selectable satellites.
7
5. Getting Started
DO
DONOT
NOTPLUG
PLUGthe
thereceiver
receiverinto
intoMain
MainPower
PowerOutlet,
Outlet,until
untilyou
youcomplete
completeall
allthe
theconnections
connectionsto
tothe
thereceiver.
receiver.
Receiver to TV with RF
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar AD-3000IP VIACCESS.
2. Connect the TV OUT socket of the EchoStar AD-3000IP VIACCESS to the RF IN of the TV set.
3. Search on the TV set for UHF channel # 38. This is the default channel where the EchoStar AD-3000IP VIACCESS
is set to.
TV
TV ANTENNA
RF IN
Receiver to VCR and then to TV with RF
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar AD-3000IP VIACCESS.
2. Connect the TV OUT socket of the EchoStar AD-3000IP VIACCESS with the RF IN of the VCR.
3. Connect the RF OUT of the VCR to the RF IN of the TV set.
4. Search on the TV set and the VCR for UHF channel # 38. This is the default channel where the EchoStar AD-3000IP VIACCESS
is programmed to.
Note : Use different UHF channels for VCR and EchoStar AD-3000IP VIACCESS.
TV
VCR
RF IN
RF OUT
TV ANTENNA
RF IN
8
Receiver to TV with Audio and Video RCAs
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar AD-3000IP VIACCESS.
2. Connect the TV OUT socket of the EchoStar AD-3000IP VIACCESS with the RF IN of the TV set.
3. Connect the Video and Audio RCAs of the EchoStar AD-3000IP VIACCESS to the Video and Audio RCAs of the TV set.
TV
TV ANTENNA
RF IN
VIDEO AUDIO
IN
IN
Receiver to TV and VCR with SCART Cables
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar AD-3000IP VIACCESS.
2. Connect the TV OUT socket of the EchoStar AD-3000IP VIACCESS with the RF IN of the VCR.
3. Connect the RF OUT of the VCR to the RF IN of the TV set.
4. Search on the VCR for UHF channel # 38. This is the default channel where the EchoStar AD-3000IP VIACCESS is programmed to.
5. Connect the SCART cable from the TV SCART of the EchoStar AD-3000IP VIACCESS to the SCART of the TV set.
6. Connect the SCART cable from the VCR SCART of the EchoStar AD-3000IP VIACCESS to the SCART of the VCR.
7. When the EchoStar AD-3000IP VIACCESS is switched on the TV set, TV set will automatically switch to the relevant SCART
input of the TV.
Note : Use different UHF channels for VCR and EchoStar AD-3000IP VIACCESS.
TV
TV ANTENNA
VCR
TV SCART
RF IN
RF OUT
9
RF IN
VCR SCART
Receiver to TV, VCR and Decoder with SCART Cables
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar AD-3000IP VIACCESS.
2. Connect the TV OUT socket of the EchoStar AD-3000IP VIACCESS to the RF IN of the VCR.
3. Connect the RF OUT of the VCR to the RF IN of the TV set.
4. Search on the VCR for UHF channel # 38. This is the default channel where the EchoStar AD-3000IP VIACCESS is
programmed to.
5. Connect the SCART cable from the TV SCART of the EchoStar AD-3000IP VIACCESS to the TV SCART from the TV
set.
6. Connect the SCART cable from the VCR SCART of the EchoStar AD-3000IP VIACCESS to the SCART of the VCR.
7. Connect the SCART cable from the DECODER SCART of the EchoStar AD-3000IP VIACCESS to the SCART of the
DECODER.
Note : Use different UHF channels for VCR and EchoStar AD-3000IP VIACCESS.
TV
TV ANTENNA
VCR
TV SCART
RF IN
RF OUT
RF IN
DECODER
VCR SCART
DECODER SCART
10
6. How to connect your dish to the EchoStar AD-3000IP VIACCESS
One Actuated Dish
1. Connect the IF OUT and LNB IN connectors using the loop through cable provided with the EchoStar AD-3000IP VIACCESS.
2. Connect the LNB IN socket of the EchoStar AD-3000IP VIACCESS to the LNB.
3. Connect motor wires to M1 and M2. Switch these connections if the motor moves to the wrong direction.
4. Connect sensor wires to M.PULSE and GND connector.
5. Connect a mechanical polarotor to +5V, GND and SKEW connectors. [optional]
6. Connect ferrite polarizer to ferrite connectors. [optional]
Universal LNB
One Actuated Dish with C/Ku feed
1. Connect the IF OUT and LNB IN connectors using the loop through cable provided with the EchoStar AD-3000IP VIACCESS.
2. Connect the cables from C and Ku-band LNB to a 12 Volt C/Ku switch.
3. Connect the coaxial cable from the 0/12 Volt switch to the LNB IN connector.
4. Connect the power cable which comes from the 0/12 Volt switch to the 0/12V(connector).
5. Connect motor wires to M1 and M2. Switch these connections if the motor moves to the wrong direction.
6. Connect sensor wires to M.PULSE and GND connector.
7. Connect polarotor to +5V, GND and SKEW connectors. [optional]
ACTUATED DISH
WITH C/KU FEED
C-band Ku-band
LNB
LNB
11
Two Fixed Dishes using DiSEqC mode
1. Connect the IF OUT and LNB IN connectors using the loop through cable provided with the EchoStar AD-3000IP VIACCESS.
2. Connect the DiSEqC 1.0 or Toneburst switch to the LNB IN connector of the EchoStar AD-3000IP VIACCESS.
3. Connect both dishes to the 2 inputs from the DiSEqC switch.
FIXED DISH # 1
(Digital or Analog)
FIXED DISH # 2
(Digital or Analog)
LNB
LNB
DiSEqC switch
12
5. Operation and Menu Program
A. Receiver and TV set-up
Check the Installation
To get the most out of the EchoStar AD-3000IP VIACCESS it should be correctly installed, the dish
should be optimally aligned and the mechanical limit switched on the dish should be set properly.
Press
/I on the remote control unit (RCU) or press
on the front panel of the EchoStar AD-3000IP
VIACCESS to switch the unit on.
The receiver is supplied with factory setting and will start up with the “Language Setting” menu.
After selecting the language settings, the ”LNB Setting” menu will be shown. Please follow the steps outlined
below to properly install the EchoStar AD-3000IP VIACCESS.
Language Setting
Language Setting
1
Menu Language
Main Audio Language
2nd Audio Language
Subtitle Language
2
You can select the desired language for the OSG (OnScreen Graphics) display using the , keys when the
“Menu Language” option is selected. Similarly you can
selected a different audio channel when the “Audio
Language” option is selected. This option allows you to
select a different language to listen to if supported.
3
4
×
English Ø
English
English
English
i
Exit
LNB Setting
LNB Setting
1
LNB Type Index (1..8)
LNB Freq.Low
LNB Freq. High
4
DiSEqC
5
DiSEqC Port
6
Polarity Control
7
LNB Freq. Band Control
8
Ku/C Control
9
0/22kHz Control
10
0/12V Control
11
LNB Power
12
Loopthrough for Analog
2
3
Select the “LNB Setting” menu in the “Installation” m
enu using the , keys.
Select the LNB type which conforms to your LN
B using the , keys.
×
Type 1 Ø
5150
5150
DiSEqC 1..4
1
13/18V
0/12V
Disable
Off
Off
On
On
i
Other parameter values should be changed
manually according to your LNB type.
Press the OK key to confirm your selection.
Exit
If you have a Mechanical Polarizer with your LNB, you have to set the “Polarity Control” parameter in this
menu to [Polarotor].
If the Loopthrough option is set to ON, the Loopthrough ports should be set according to the diagrams on
pages 11. If no Loopthrough is used this option should be set to OFF.
13
Antenna Installation
Antenna Installation
First the east and west limits have to be set before
any satellites can be programmed.
1
East Limit
2
Press the key on the “East Limit” parameter line.
The initial value of 5000 will decrease as the dish i
s moved. Keep moving the dish unit the east limit i
s reached. If the dish to the west when you press th
e key, reverse the motor wires.
×
West Limit
Not Se t
Ø
Not Set
i
Exit
If either the numeric value is not shown or the message
“...Motor Error...” is displayed on the lower left part of t
he screen, then,
1) an error occurred when moving the dish(which could be caused by i.e. loose wires), or
2) the dish has reached its east limit. In this case continue with the installation procedure.
Move the dish a few counts to the west by pressing the key and press the OK key to store east limit in this p
osition. The indicated number will be set at 1000 and the highlight will be moved down to the “West Limit” li
ne. Now set the west limit by moving the dish using the key until you have reached the dish limit. The indica
ted number will increase from 1000. Move the dish back a couple of counts using the key and press the OK
key to store the west limit.
The dish limits are now stored in the receiver and t
he dish is the most western position. Press the SA
T key to start the “Auto Sat” function or you can pr
ess MENU to program the satellites manually.
Antenna Installation
East Limit
1
2
If you do not have a moveable dish, just press the
OK key twice to program the east and west limit in
the same position. This will be indicated by a
numeric value of 1000 for both limits.
West Limit
1000
1070
i
Exit
Press SAT to go to the Auto SAT feature.
Press menu if you want to program the satellites manually.
Press Exit to return to TV/Radio channel.
Auto SAT
Please Store most western satellite
Satellite
018.0° W
×
INTEL705
LNB Type
Type1
TP/Polar/SR(Digital)
11525/H/12225
Skew
Not set
Position
E
1000
W
Realign dish
+00
Search type
Auto Search
Start Search(Press OK)
1
2
3
4
5
6
7
88
Now press the or key to select the most western
position you can receive.
Press the OK key.
EL
Select the Position option and move the dish using
the key to correct location of the western satellite.
Peak the dish to obtain the highest signal quality
using the and keys. Then press the OK key to
store this setting.
14
Ø
WL
Signal Level
11%
Signal Quality
00%
Go back to Satellite option using the key.
Please Store middle satellite
Now press the or key to select the middle
satellite.
1
2
3
4
5
6
7
8
Press the OK key.
Select the position using the key and with the
key move the dish to the correct location of the
middle satellite. Peak the dish to obtain the
highest signal quality using the and keys.
Satellite
028.2° E
LNB Type
TP/Polar/SR(Digital)
Skew
Position
Realign dish
Search type
Start Search(Press OK)
ASTRA2
Type1
11478/H/30000
Not set
E
1238
W
+00
Auto Search
[ E 1238 W ]
EL
WL
Signal Level
12%
Signal Quality
00%
Then press the OK key to store this setting
Please Store most eastern satellite
Go back to the Satellite option using the key.
Satellite
004.0 ° W
LNB Type
TP/Polar/SR(Digital)
Skew
Position
Realign dish
Search type
Start Search(Press OK)
1
2
3
4
5
6
7
8
Now press the or key to select the most
eastern satellite you can receive.
Press the OK key.
AMOS1
Type1
11224/H/27500
Not set
E
1053
+00
Auto Search
W
EL
Select the Position option using the key move
the dish to the correct location of the eastern
satellite. Peak the dish to obtain the highest
signal quality using the and keys.
Press the SAT key to let the receiver calculate all
intermediate satellite positions. All selected satellite
positions are now stored for both the digital and
analog mode.
WL
Signal Level
12%
Signal Quality
00%
Auto SAT
1
Select Satellite
019.2 °E
×
ASTRA1
Ø
* Page Change = Ú,Ù
* Press SAT to Calculate satellite positions
ü CAKRAWAR
ASIASAT3S
GORIZT25
ASIASAT2
ABC
ü MESAT
ST1
INSAT2E
Press the MENU key twice to return to the installation
screen. Select Auto Channel Search (for more
information on this option please refer to page 20).
The EchoStar AD-3000IP VIACCESS will start the
search on the most eastern satellite.
107.7° E
105.5° E
103.0° E
100.5° E
100.5° E
091.5° E
088.0° E
083.0° E
THAICOM
APSTAR2R
PAS4
ü ASTRA1
078.5° E
076.5° E
068.5° E
018.0° E
i
Delete
Add
Exit
Auto SAT
1
Select Satellite
019.2 °E
* Page Change = Ú,Ù
* Press SAT to Calculate satellite positions
ü CAKRAWAR
ü ASIASAT3S
ü GORIZT25
ü ASIASAT2
ü ABC
ü MESAT
ü ST1
ü INSAT2E
107.7° E
105.5 ° E
103.0° E
100.5° E
100.5° E
091.5° E
088.0° E
083.0° E
ü THAICOM
ü APSTAR2R
ü PAS4
ü ASTRA1
×
ASTRA1
078.5° E
076.5° E
068.5° E
018.0° E
i
Delete
15
Add
Exit
Ø
Program Satellites
Program Satellites
The EchoStar AD-3000IP VIACCESS now has
programmed the position of all selected satellites.
The next step is to store all channels on these
satellites. To do this press the MENU key, select
the Installation option followed by the Program
Satellites option. Use the key to select the next
satellite and press the OK key. The dish will
move to the selected satellite.
× HOTBIRD Ø
Satellite
013.0? E
LNB Type
Type 1
TP/Pol/SR(Digital)
11662/V/27500
Skew
Not set
Position
E
1070
W
Re-align Dish
+00
Search Type
Auto Search
Start Search (Press OK)
[E 1070 W]
1
2
3
4
5
6
7
8
EL
WL
Select Start Search to store all channels.
Repeat this procedure for all satellites.
Signal Level
10%
Signal Quality
5%
Motorized Dish Setting
Motorized Dish Setting
1
If you are not satisfied with the Limit parameters e.g. since the
mechanical limits might not be set properly, you can erase the
position data and start again after adjusting the mechanical
limits at the dish.
Antenna Installation
Erase Position Data
2
i
Exit
Go in to the “Motorized dish setting” menu with the key to “E
rase Position Data” and press the OK key. Then go to “Erase
All Satellite Data” press the red key twice. Press the MENU k
ey, go to Installation, Motorized Dish Setting, Antenna Installat
ion, press the OK key and proceed from start.
Motorized Dish Setting
1
2
Antenna Installation
Erase Position Data
i
Exit
Erase Position Data
Erase Position Data
Select in the Erase Position Data Menu “Set Present Sat as f
ixed”, using the , keys.
If signals from this satellite are received with a fixed dish, th
e movable dish will not move to this satellite.
1
2
Set present SAT as fixed
Erase All Satellite Data
i
Delete
16
Cancel
Exit
User’s Setting
User’s Settings are only accessible via the Installation screen.
Language Setting
User’s Setting
Language Setting
1
1
2
3
4
Language Setting
Local Time Setting
A/V Output Setting
About Echostar
i
×
Menu Language
Main Audio Language
2nd Audio Language
Subtitle Language
2
3
4
English Ø
English
English
English
i
Exit
Exit
You can select the desired language for the OSG (On-Screen Graphics) display using the , keys when the
“Menu Language” option is selected. Similarly you can select a different audio channel when the “Audio
Language” option is selected. This option allows you to select a different language to listen to if supported.
Subtitle
Select the “Subtitle Language” in the “Language Setting” menu. While viewing a
channel, the subtitling option is available only when the selected subtitling language
is provided by the broadcaster.
To check if the subtitling language is available, press “
” key on the remote
control unit, to show a list with all available subtitling languages.
Subtitle
None
Eng
Ita
Local Time Setting
To set your local time, input all the required data for the time
and date. This information has to be entered to enable
recording of the programs of your choice.
Local Time Setting
1
After entering the correct data for year, month, date, day,
hour, minute, select option 7 (Press the OK key to set the
time) and press the OK key to save the data.
It is recommended that the time and date set in this menu is
the same as of your VCR.
Now that the date and time has been set you could edit the
VCR timer settings.
17
2
3
4
5
6
7
Year
Month
Date
Day
Hour
Minute
Press OK to set the time
×
1999
Ø
Jan.
01
Sun.
00
00
Local Time = --:-i
Exit
A/V Output Setting
Aspect
A/V Output Setting
Please select your TV format.
1
2
3
4:3 for normal screen TV
16:9 for wide screen TV
4
5
Banner
You can select the time out
time(2,3,4,5,8,10 secs) of the banner
information about the current channel and
program using the , keys.
Aspect
Banner
Sub. backg.
<<< UHF Tuning >>>
PAL
Channel
Frequency =
×
4:3
Ø
3Sec
On
B/G
38
607.25MHz
i
Exit
Sub.backg.
Select ‘On’ for Subtitle background on TV (Subtitle background).
UHF Tuning
You can select the type of Video standard by using the , keys.
* Video standard : PAL B/G,I , D/K
Select the vacant channel considering your local channels and preset channels below.
* Pre-set : Ch 38 for PAL B/G,I
Ch 40 for PAL D/K
UHF frequency is set automatically according to the channel selection.
About EchoStar
You can see the details of the company
information.
About Echostar
Company info
Company
Address
City
Country
If you have any questions about the EchoStar
AD-3000IP VIACCESS, firstly contact your l
ocal dealer.
Phone Number
Fax Number
Unit info
Unit
Software version
Home page
Echostar Intl. Corp.
Schuilenburglaan 5a
7604 BJ Almelo
Netherlands
+31 546 815122
+31 546 814691
AD-3000IP VIACESS
XXXXXX
HTTP://www. echostar.nl
i
Exit
18
B. Main menu and Installation
Main Menu
Main Menu
1
Press the MENU key to display the “Main Menu” o
n the screen.
Select a sub-menu using the , keys or the numeric k
eys. Please note that the OK key is always a confirma
tion of your selection. To go back to the previous me
nu, press the MENU key.
2
3
4
5
6
7
8
TV Channels
Radio Channels
Parental Control
VCR Timer
Edit
Installation
Select Satellite
Conditional Access
I
Exit
Installation
Installation
Installation Lock
Program Satellites
1
Enter PIN Code
SMATV Configuration
2
[ ? ? ? ?]
User’s Setting
3
4
LNB Setting
5
Motorized Dish Setting
6
Advanced Installation
The Installation Lock,“Enter PIN code” menu is displayed only when the Installation and Edit Lock is se
t as [ON]. The initial code is set as [0000] but you can change it (See “Change PIN code” on page 21).
Program Satellites
Program Satellite
1
2
3
4
5
6
7
8
Refer to the Signal Quality bar and the Signal Lev
el bar at the bottom of the screen. It is recommend
ed that the signal is at the Medium level or higher.
If it is not , please adjust your satellite dish.
Satellite
028.2° E
LNB Type
TP/Polar/SR(Digital)
Skew
Position
Re-align dish
Search type
Start Search(Press OK)
×
ASTRA2
Ø
Type1
11478/H/30000
Not set
E
1172
W
+00
Auto Search
[ E 1172 W ]
EL
This menu is to align your dish to the selected satellite.
If you set the “Polarity Control” parameter in the “LNB
Setting” menu as “Polarotor” or “Ferrite”, you can adjust
the “Skew” parameter in this menu while you are watchi
ng the signal level at the same time.
i
WL
Signal Level
12%
Signal Quality
00%
You can move the dish using the , keys when the “Position” option is selected. . To locate a satellite move the
dish until you have the location of the satellite at which the best signal quality is achieved. Press the OK key wh
ile still on the “Position” option the store the position. The stored locations for each satellite are shown above th
e Signal Level bar.
If you are unable to get any signal quality, please check the LNB Setting to ensure you have selected the correct
LNB and switch settings.
In some cases it might be necessary to reposition all satellites at once. This can be achieved with the “Re-align di
sh”option.
19
Auto Search
Using the Auto Search option, the EchoStar AD-3000IP
VIACCESS searches for all available channels(Radio and
TV) on the currently selected satellite. The names of the fo
und TV channels are shown on the left and the total numb
er of found TV and Radio channels are mentioned on the r
ight.
Auto Search
ASTRA1
Arte
Beta BC
BD1
Estilo
Musicals
Reqqae
Found TV ch. : 240
Found RAD. Ch. : 100
Channel searching status
0%
50%
Note: To stop searching press the
key on the
remote control or on the front panel. This
cancels the searches and the found
channels will be discarded. All other keys
of the remote are disable during searching
Index
45
Freq
12670
SR
22000
100%
FEC
5/6
Polarity
vertical
SMATV Configuration
SMATV Configuration
A Satellite Master Antenna Television (SMATV) system
which is intended for the distribution of television and
sound signals to household in one or
6 more adjacent buildings.
A SMATV System represents a means for sharing
the same resources among several users for satellite and
terrestrial reception, and it is designed to perform
the adaptation of the satellite TV signals to the SMATV
channel characteristics.
1
2
3
4
5
Symbol rate alternative 1
Symbol rate alternative 2
Symbol rate alternative 3
FEC
Start Auto Search
×
27500 Ø
27500
27500
AUTO
i
Exit
EchoStar AD-3000IP VIACCESS VIACCESS has a SMATV-IF facility to operate with SMATV.
This configuration allows the direct distribution of the QPSK signal received from the satellite
to the SMATV-IF distribution network in the extended IF band (above 950 MHz).
Before you start, you have to check your condition whether it is possible to use this facility or not in your
households. (You can ask your household supervisor.)
If EchoStar AD-3000IP VIACCESS VIACCESS is connected to a SMATV network, select “SMATV
Configuration”.
The most common alternatives for “Symbol rate” and “FEC” are already preprogrammed.
(When you need to change the “Symbol rate” for the exceptional frequency, select as you know.)
Move to “Start Auto Search” and just press OK.
Then, the “Auto Search” procedure will start.
To cancel the processing while the “Auto Search” is proceeding, press the MENU key.
20
TV Channels
TV Channels
You can select the channel you would like to watch either b
y pressing the numeric keys for the channel number or by m
oving the highlighted bar to the channel of your choice usin
g the , keys. Press the OK key to select the channel.
1
2
3
4
5
6
7
8
ASTRA1
Paris Premere
Voyage
Contact TV
LC I
Cabal J
JDF 1 Info-Kanal
Star Kino
CNN
019.2? E >
F
F
F
F
F
F
F
F
* Press the , keys to move one page up or down.
Radio Channels
Radio Channel
ASTRA1
1
2
3
You can select the channel you would like to watch either b
y pressing the numeric keys for the channel number or by m
oving the highlighted bar to the channel of your choice usin
g the , keys. Press the OK key to select the channel.
4
5
6
7
8
< 019.2? E >
Hit Liste
Blues
Classic rock
Soft Rock
Generation ROC
Love Songs
Dance
REE
F
F
F
F
F
F
F
F
* Press the , keys to move one page up or down.
Parental Control
With parental control it can be prevented that a TV channel can be watched, a Radio Channel can
be heard, the receiver settings can be changed or an unauthorized change in the installation is
performed.
Parental Control
Parental Control
1
Enter PIN Code
2
3
4
5
[ ? ? ? ?]
i
Off
Off
i
Exit
Change PIN Code
Change PIN Code
TV Channel Lock
Radio Channel Lock
Receiver Lock
Installation & Edit Lock
Exit
The pre-programmed PIN (Personal Identification Number) code is set as
[0000]. If you want to change it, please follow the procedure shown as
before.
21
TV Channel Lock
TV Channel Lock
33
34
35
36
37
38
39
40
Press the Red button to lock / unlock the selected c
hannel.
Locked channels will be skipped when scrolling
through the channels.
TV Channels
Paris Premere
Voyage
Contact TV
LC I
Canal J
DF 1 Info-Kanal
Star Kino
CNN
i
Press the VIEW key to see a thumb nail of the current
channel in this menu.
Lock
Unlock
Exit
Note) The color of the highlighted bar turns to red
when it is on a locked channel.
Receiver Lock
If the Receiver Lock is [ON], you have to input the correct code to operate
the receiver.
Installation Lock &
Edit Lock
If the Installation & Edit Lock is [ON], you have to input the correct code to ente
r directly into the “Installation” and “Edit” menu..
VCR Timer Setting
You can edit “VCR Timer Setting” only after you
input all the data in the “Local Time Setting”
VCR Timer
1
Total of 5 events are programmable for your
VCR recording with the EchoStar AD-3000IP
VIACCESS.
2
3
4
5
6
7
Select an event number from 1 to 5, choose your
wanted Satellite and Channel (only searched
satellites and channels are available to be selected),
input Start time and Stop time (not 12-hours &
AM/PM, but 24 hour system), select your recording
time among O(once) / D(daily) / W(weekly) /
M(monthly).
“On” for recording (On/Off) is only available when
all the data are properly input or selected.
8
×
1
Ø
Event Number
Date(mm/dd/yyyy)
??/??/????
Satellite
ASIASAT2
Channel
Saudi Ch1
Start Time ( hh:mm)
??:??
Stop Time (hh:mm)
??:??
Type(O/D/W/M)
Once
Recording(On/Off )
OFF
Current Date & Time - Nov./20/1999(Sat.) 20:00
i
Exit
If recording “On” is not available, you may check the followings ;
1) Overlapped Events : Check your prior setting for recording. The time for recording(from Start to Stop)
might be overlapped with the new setting.
2) Local Time Setting : Any event which starts earlier than your “Local time Setting” might not work.
Please turn on your VCR to record an event.
22
Edit TV Channel
The “Enter PIN code” Menu is displayed only when the Installation and Edit Lock is set as [ON]. The in
itial code is set as [0000] but you can change it (See “Change PIN code” on page 21).
Edit
Edit TV Channel
1
2
3
4
Edit TV Channel
Edit Radio Channel
Edit Transponder
Edit Satellite
ASTRA1
Paris Premere
Voyage
Contact TV
LC I
Canal J
DF 1 Info-Kanal
Star Kino
CNN
49
50
51
52
53
54
55
56
i
i
Delete
Exit
Cancel
Move
Favorite
Exit
You can move to the channel that you want to edit by using , keys.
Also you can move to the highlighted bar directly by inputting the channel number.
FAV Channels
You can create a group of up to 96 channels in the
“Edit TV Channel” or “Edit Radio Channel”
menu. To include a channel in the FAV list, select a
channel and press the blue key on the remote control.
To select a favorite channel from the FAV list, press
the FAV key.
Edit TV Channel
ASTRA1
Paris Premere
Voyage
Contact TV
LC I
Canal J
DF 1 Info-Kanal
Star Kino
CNN
49
50
51
52
53
54
55
56
To view a thumb nail representation of the currently
selected channel, press the
key on the remote
control.
i
Delete
Edit Radio Channel
Cancel
Move
Favorite
Edit Radio Channel
1
2
Use the same procedure for the Radio Channel
s as used for editing the TV Channels as above.
3
4
5
6
7
8
ASIASAT2
Hit Liste
Blues
Classic Rock
Soft Rock
Generation ROC
Love Songs
Dance
REE
i
Delete
23
Cancel
Move
Favorite
Exit
Exit
Edit Transponder
Edit Transponder
ASIASAT2
Network(3661H)
Network(3706H)
Network(3713H)
Network(3720H)
Network(3727H)
Network(3734H)
Network(3764H)
Network(3766V)
1
2
3
4
5
6
7
To delete a transponder, press the red key when the
highlighted bar is located at the transponder you
want to delete.
8
To add a transponder, press the blue key.
And then, the “Edit/Add SAT or TP” menu will be displ
ayed, and you can add a transponder in that menu.
Edit Satellite
Channel List
CHANNEL ONE
Ch.8 - OS Down
Ch.9 - OS Down
Ch.370. Audio
Ch 371. Audio
Ch.372. Audio
Ch.373. Audio
Ch.374. Audio
Ch.375. Audio
Ch.378. Audio
i
Delete
Cancel
Exit
Add/ TP
Edit Satellite
Satellite Name
1
ASTRA1
To delete a satellite, press the red key when the
highlighted bar is located at the transponder you
want to delete.
WL
EL
To add a satellite, press the blue key.
And then, “Edit/Add SAT or TP” menu will be displaye
d, and you can add a satellite in that menu.
i
Delete
Select Satellite
Cancel
Add SAT
Exit
Select Satellite
1
ASTRA1
APSTAR2R
2
To move to another satellite you want to watch, press the
SAT key( ) on the remote control and choose the proper
satellite with , keys.
Press OK to confirm.
WL
EL
i
Exit
Conditional Access
Conditional Access
< Common Interface >
1
2
From here you will get access to information and
menus from the CI module(Irdeto, Conax,
Cryptowork, Nagravision and Viaccess encryption).
This information may vary depending on the module.
3
Common Interface
Slot 1 : Module not installed
Slot 2 : Module not installed
Viaccess Embedded
Smart Card Information
i
Please see the documentation delivered together with
your CI module.
< Viaccess Embedded >
Insert the Viaccess smart card into the Smart Card slot on the Front Panel. The chip should be faced
upwards.
24
Exit
ALT Audio
L Audio
Audio RR
L
R
1
If more than one audio channel is provided by
the broadcaster on a specific channel, you can
activate the audio mode display by pressing the
key.
Guide
While watching or listening to any channel and you
want to know more information regarding the
program shown, press the EPG key on the remote
control to display the “TV Guide” or the “Radio
Guide”. This information may be provided by the
broadcaster. You can move to another channel by
pressing the , keys or the , keys.
TV Guide
11: 52
1
2
3
4
5
6
7
8
Now
RAI1
Linea verde - In ?
RAI2
No Information
RAI3
Rai Sport Cavale ?
RAIwidescree
Wide Screen
RAISPORT sate Rai Sport Sat
TEST2RAI
No Information
TEST3RAI
No Information
CNN
No Information
11:10~ 11:55
No Time
11:27~ 12:02
11:00 ~ 14:00
11:00~ 14:00
No Time
No Time
No Time
i
Radio
Next
Info
Select
Exit
Please refer to the function of the keys belows.
1) Red(TV/Radio) key : Switches the “TV Guide” and the “Radio Guide” by pressing this key.
2) Green(Now/Next) key : Switches the program guides of “Now” and “Next”
3) Yellow(Info) key : Shows detailed information of the selected channel.
4) Blue(Select) key : Goes to the viewing mode of the selected channel.
5) White(Exit) key : Exits the TV/Radio Guide
Pressing the Yellow(Info) key shows the detailed
information of the program and thumbnail of the
current channel.
TV Guide
RAI1
natura : Linea verde - In diretta dalia natura
Un programma di Sandro Vannucci a cura do
Gian Stefano Snoto produttore esecutivo
Gianoiero Ricci
11:19~ 11:55
i
EPG
25
Select
Exit
C. Advanced Installation
Advanced Installation
Advanced Installation
1
2
3
4
5
You can select the “Advanced Installation” menu
on the “Installation” menu of Main menu by using
the Channel up/down keys (Ù,Ú).
Edit/Add SAT or TP
Edit LNB Local Freq.
Auto Scan
Auto Sat
Reset(Factory Default)
i
Exit
Edit/Add SAT or TP
Edit/Add SAT or TP
1
Satellite
Longitude
Digital/Analog
TP/Signal Quality
4
LNB polarization
5
Symbol Rate
6
7
FEC
8
Channel Name
9
Video PID
10
Audio PID
11
PCR PID
2
3
Edit/Add SAT or TP
×
ASTRA1
019.2 °E
Digital
0
Vertical
0
AUTO
????????
0
0
AUTO
Ø
1
2
3
Satellite
Longitude
Digital/Analog
Channel
4
Frequency
5
Polarity
6
7
C/Ku
8
Decoder
Decoder Level
9
10
Low Threshold
11
Skew
12
Ú More Ú (Audio Setting)
×
ASTRA1
019.2 °E
Analog
RTL_2
11214.00
Horizontal
Ku
Off
2
Off
Not set
To edit any satellite or transponder, select satellite and transponder to be edited.
You can convert from digital to analog and vice versa, at “Digital/Analog” parameter.
You can change the name of the satellite, transponder, channel name and such.
To change channel name, place highlight bar to “8 Channel Name” and keep pressing
one of either the or keys till it reaches “??? Add ch”.
Then, press the OK key to activate graphic key board and now you can edit the name up to 10-character
length. For some words,, maximum number of the characters is 11. And, mostly 8 characters from
the start shall be shown on the menu when you finish changing name.
Note 1) You should execute “Auto Search” after editing the satellite or the transponder.
If “Auto Search” is executed after adding the new transponder, all channels of the added
transponder will be searched and stored automatically.
CAUTION: By doing an Auto Channel search you will lose all the data
(e.g. FAV, Lock…) which you have edited.
Note 2) You can add or edit totally of 50 satellites. This includes the pre-programmed satellites.
The receiver has the cap ability to store up to 999 transponders and 5000 channels.
26
Ø
Edit LNB Local Frequency
Edit LNB Local Frequency
LNB Local Frequency
0..9
×
11300
Ø
You can edit up to 8 local frequencies by using numeric
keys.
And if you want to save the newly edited frequency, pres
s the OK key.
i
Exit
Auto Scan
Auto Scan
You can scan analog channels of the chosen satellite automa
tically in this menu.
ASTRA1
1
2
3
4
Press the OK key at the “Start” bar to start channel scannin
g.
By doing a channel scan you will loose the channel names.
This can be redone by going back to factory default.
Polarity
Channel
Frequency
Start
× Horizontal Ø
000
3000.00
i
This function assists end-users to speed up the searching
/storing process. It may be required to fine-tune the video
by adjusting the frequency manually.
Exit
Reset (Factory Default)
Reset (Factory Default)
* If you want Factory Reset, press Red button
If you want to reset all the data edited, press the Red b
utton twice.
i
Reset
27
Cancel
Exit
6. Specifications
Digital Section
1. Tuner & channel
Input connector
Output connector
Frequency range
Input impedance
Signal level
IF frequency
IF bandwidth
LNB power & polarization
22kHz tone
Demodulation
Input symbol rate
FEC decoder
1 x F type with loop through
1 x F type 75 Ohm
950MHz to 2150MHz
75 Ohm
-25 to -65dBm
480MHz
36MHz
Vertical
+13.5V - +14.5V
Horizontal
+17.5V - +18.5V
Frequency
22kHz 2kHz
Amplitude
0.6Vp-p 0.2Vp-p
QPSK
2 - 32Msps
Convolutional code rate
1/2, 2/3, 3/4, 5/6 and 7/8 with constraint
Length K=7
2. MPEG transport stream A/V decoding
Transport stream
Profile & level
Input T/S data rate
Aspect ratio
Video resolution
Audio decoding
Audio mode
Sampling rate
MPEG-2 ISO/IEC 13818
Transport stream specification
MPEG-2 MP @ ML
90Mbit/S max.
4:3, 16:9 with pan vector
720 x 576(PAL), 720 x 480(NTSC)
MPEG-1 Audio Layer 1 & 2, Musicam
Stereo, Dual channel, Joint stereo, Mono
32, 44.1 and 48kHz
3. Memory
Flash memory
Program DRAM
EEPROM
up to 2 Mbytes
up to 8 Mbytes
2 Kbytes
4. A/V & data in/out
SCART
RGB video output
0/12V out
CVBS video out
TV x 1, VCR x 1, Decoder x 1
TV SCART
RCA x 1
RCA x 1, SCART x 2 (TV, VCR)
28
S/PDIF out
Analog audio out
Data interface
RCA x 1
RCA x 2 (L-Ch x 1, R-Ch x 1), SCART x 2 (TV, VCR)
Resolution 16bit DAC
Output level 2Vrms max.
Volume & mute control
RS232C, Baud Rate 9600 - 115200, 9 Pin D-Sub
5. PCMCIA
Number of Slot
Type
2
I, II DVB Common interface standard
6. Conditional Access
Embedded Viaccess
1 Smart Card Reader
7. RF-Modulator
RF-connect
Output Frequency
Output channel
TV standard
75 Ohm, IEC169-2, male/female
470MHz to 860MHz
Ch21 - 69
PAL D/K, PAL B/G , PAL I
8. Power supply
Input voltage
Type
Power consumption
Protection
AC90 - 240V, 50/60Hz (Receiver / Positioner)
Linear PWM
240W max.(below 7W max. for standby mode)
Separate internal fuse and chassis grounding.
The input shall have lightning or electric shock protection.
9. Physical specification
Size(W x H x D)
Weight
370mm x 60mm x 280mm
about 3 Kg
10. Environment
Operating temperature
Storage temperature
+5ºC - +40ºC
-40ºC - +65ºC
11. Positioner
Satellite position
Azimuth & Skew control
Output power
Sensor type
Ferrite control
50
6 Push terminal
(M1, M2, M.Pulse, +5V, GND, Skew)
36VDC, 5A max. (during 5 minutes) (SMPS)
Reed or Hall effect switch
2 Push terminal(+,-)
29
Analog Section
1. RF
Input frequency range
Input impedance
IF bandwidth
IF frequency
Input signal level
Threshold
900MHz to 2150MHz
75 Ohms
27MHz
479.5MHz
-60 to –30dBm
6dB Typ. (3dB: low threshold mode, 32 Steps)
2. Audio
Subcarrier tuning range
De-emphasis
IF bandwidth
Audio frequency response
Output impedance
Output level
5.0 to 9.0MHz
J-17 / 50uS / 75uS / Adaptive (Panda-compatible)
130kHz / 150kHz / 230kHz / 280kHz / 330kHz / 500kHz
20Hz to 15kHz
600 Ohms
2.0 Vrms Max.
3. Video
Format
De-emphasis
Output impedance
Frequency response
Output level
Invert / Normal (C/ Ku)
Selectable video output
CCIR Recommendation 405-1, 625 lines
75 Ohms
50Hz to 5.0MHz
1 Vp-p normal
4. Decoder format
Format
Output impedance
Output level
Base band
De-Emphasized, Unclamped, Un-Filtered,
De-Emphasized, Unclamped, Filtered,
De-Emphasized, Clamped, Filtered
75 Ohms
1 Vp-p nominal
30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising