- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- User manual
advertisement
THANK YOU FOR PURCHASING THE BARACUDA ® G3 ™ .
YOUR BARACUDA G3 HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY
INSTALLED AND TO PROVIDE YEARS OF LOW MAINTENANCE OPERATION.
PRIOR TO INSTALLING YOUR NEW BARACUDA G3 , PLEASE DO THE FOLLOWING:
1) Complete and return the warranty card.
2) Record your purchase information on the spaces provided below.
3) Attach your invoice (or a copy) to this page.
These actions will insure prompt warranty service, should it be required. Simply present your owner’s manual, along with the invoice at any of our authorized warranty centers nationwide.
RECORD YOUR BARACUDA G3 POOL CLEANER DATA HERE:
Date of Purchase _____________________________________________________________________________________________________________
Purchased From _____________________________________________________________________________________________________________
City __________________________________________________ State/Province _______________________ Zip/Postal Code____________________
Serial No: ________________________________________________________ (serial number located on underside of machine head)
BARACUDA G3 LIMITED WARRANTY
This Baracuda G3 was carefully inspected before shipment from our warehouse. Upon unpacking, if any part proves defective or missing, please notify Zodiac Pool
Care, Inc. immediately. Please consult owner’s manual for complete instructions on the installation and operation of your Baracuda G3.
ZODIAC POOL CARE, INC. WARRANTS THE BARACUDA G3 POOL CLEANER AGAINST ALL MANUFACTURING DEFECTS AND ALL WEAR
AND TEAR FOR THE FIRST TWO (2) YEARS INCLUDING THE BARACUDA G3 HOSE. ALL WARRANTIES ARE EFFECTIVE FROM THE DATE
OF PURCHASE.
Should this product prove defective in workmanship, materials or wear during the applicable warranty period, the consumer’s sole and exclusive remedy shall be such repair or replacement of the product as provided below.
THIS LIMITED WARRANTY EXCLUDES THE FOLLOWING:
1. Discoloration of the Baracuda G3 pool cleaner. This is caused by reaction to ultraviolet rays and the chemicals used in the pool water. Discoloration does not affect the operating ability of the Baracuda G3. Therefore, this Limited Warranty does not cover the replacement of discolored parts.
2. Damage to or malfunction of the unit resulting from excess chlorination or improper water chemistry balance.
3. Replacement of parts which fail or become defective as a result of improper installation, negligence, misuse, abuse or tampering by unauthorized repair personnel.
4. Age, pool water imbalance, and improper installation can cause vinyl pool liners to become brittle or unduly wrinkled. Corrosion of the supporting walls and /or irregularities in the pool base may also cause liner failure. The use of this product in such an environment is at the pool owner’s risk. Therefore, the pool owner hereby releases the manufacturer from any and all claims for damage where these conditions exist.
5. The Baracuda G3 is designed for use in inground pools only. If unit is used in any other application, the pool owner hereby releases the manufacturer from any and all claims. This misuse will void all warranty on the unit.
THE LIMITED WARRANTY PROVIDED HEREIN IS THE SOLE AND EXCLUSIVE WRITTEN WARRANTY WITH RESPECT TO THE
BARACUDA G3 POOL CLEANER. ALL IMPLIED WARRANTIES IMPOSED BY APPLICABLE LAW, INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO EACH COMPONENT OF THE
BARACUDA G3 ARE LIMITED TO THE DURATION OF THE EXPRESS LIMITED WARRANTY WITH RESPECT TO SUCH COMPONENT. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
In no event shall Zodiac Pool Care, Inc. be liable in contract or in tort, or under any other legal theory, for lost profits or revenues, loss of use or similar economic loss, or for indirect, special, incidental, consequential or similar damages, even if it has been advised of the possibility of such claim. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
No claim under this Limited Warranty will be recognized unless the registration card, included in your box, is completed and returned within fifteen (15) days of the purchase date. Only the original purchaser may submit a claim under this Limited Warranty. Purchaser’s claims against Zodiac Pool Care, Inc. shall be limited to those claims which may be asserted under the Limited Warranty relating to any defect, malfunction or wear of the Baracuda G3.
To obtain warranty replacements or repair, call for authorization at (888) 786-7797. When calling, always supply serial number, evidence of purchase date, retailer and a brief description of the problems/defects encountered. Zodiac Pool Care, Inc. reserves the right to repair or replace all defective or worn parts covered by this
Limited Warranty and return same to purchaser, freight collect.
Zodiac Pool Care, Inc. assumes no responsibility for any warranties or representations made by other individuals or businesses beyond the express terms contained in this Limited Warranty.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
2
For sale and use in the United States, Canada and Mexico only. This pool cleaner is not warranted or guaranteed outside of the United States, Canada or Mexico.
This pool cleaner is covered by one or more of the following U.S. and Canadian patents and Canadian registered design:
U.S. patent nos. 4,642,833 – 4,742,593 – 5,315,728 – 5,421,054.
Canadian patent nos. 1,254,105 and 1,256,262.
OTHER PATENTS PENDING.
HOW YOUR BARACUDA
®
G3
™
WORKS
Your pool pump pulls water from the main drain and the skimmer through a strainer basket, then pushes the water through the filter system and back into the pool through the return inlets.
The Baracuda G3 connects to the skimmer or dedicated vacuum line with the hose sections provided.
Water flows through the diaphragm of the Baracuda G3 at a rate of 14 to 19 GPM.
The "Pool Pulse" provides a way to measure the amount of water flow. The "Flowkeeper Valve" provides a way to regulate the amount of water flow.
Diverting or re-directing the return inlets downward breaks up the circulation pattern of water within the pool. This allows random cleaning around the pool.
Most common problems can be eliminated, by reading through the entire manual before installing your new Baracuda G3.
POOL COMPONENTS
You will interface with the following components of your pool during installation of the Baracuda G3.
FILTER
PUMP
PUMP
STRAINER
BASKET
DEDICATED
VAC LINE
SKIMMER & MAIN
DRAIN VALVES
RETURN
INLET
SKIMMER RETURN
INLET
MAIN
DRAIN
All diagrams are provided for reference and for terminology used throughout this manual. Your pool may vary.
3
OPERATIONS GUIDE
Warranty Information...................................................................................2
How it Works ...............................................................................................3
Pool Preparation......................................................................................... 5
Assembly.................................................................................................... 6
FlowKeeper ™ Valve ......................................................................................6
Pool Pulse ™ ...................................................................................................7
Hose Assembly & Balance ..........................................................................8
Installation....................................................................................................9
Adjustments ...............................................................................................13
Care and Maintenance................................................................................14
Accessories ................................................................................................16
Troubleshooting .........................................................................................17
Parts Diagram ............................................................................................ 18
Let Us Help ............................................................................................... 19
Check that the following parts are included:
(1) FlowKeeper™
Valve (1) Cleaner head (1) Finned disc
(1) Universal
Valve Cuff (1) Hose weight
(2) 45-degree installation adapter elbows (1) Pool Pulse™
4
(12) Hose Lengths (1) 4 1 /
2
" Connector (1) Hose protector net
If assistance is required, call 1-888-786-7797
Important: for Vinyl Liner Pool Owners
Vinyl liners are subject to deterioration or damage due to age, the effect of chemicals, corrosion or failure of the supporting walls; as well as improper installation, maintenance or cleaning of the supporting walls or base.
Before installing the Baracuda ® G3 ™ , examine the interior of your pool carefully.
If your vinyl liner is brittle or has stones, wrinkles, roots or metal corrosion in contact with the underside of the liner, or has damage to the base material or supporting walls, do not install the Baracuda G3 before having a qualified professional perform the necessary repairs.
Baracuda will not be responsible for liner damage caused by (1) a Baracuda G3 which is out of warranty or in disrepair, or (2) a Baracuda G3 used in a pool having a aged or deteriorated liner. YOU ARE RESPONSIBLE FOR LINER DAMAGE
IF YOU USE THE BARACUDA G3 UNDER CONDITION (1) OR (2).
STEP 1 - POOL PREPARATION
To ensure proper performance and eliminate unnecessary adjustment, please do the following before installing your new Baracuda ® G3 ™ .
❑ Close the main drain - (This allows the flow to be regulated by the "Flowkeeper
™ Valve")
❑ Manually Vacuum the pool - (This eliminates unnecessary adjustment later)
❑ Clean the pool filter and empty the skimmer and pump strainer baskets - (filter pressure rises as debris is cleaned from the water thus reducing flow)
❑ Divert the pool return inlets downward - (IMPORTANT!)
Your Baracuda G3 must move randomly throughout the pool. Water circulating at the surface will influence the hose-limiting coverage.
BEFORE ADJUSTMENT
TOP VIEW SIDE VIEW
AFTER ADJUSTMENT
TOP VIEW SIDE VIEW
To adjust the return inlet: loosen the lock ring and redirect the eyeball downward, then retighten the lock ring. If the eyeball is difficult to adjust, insert a screwdriver inside the eyeball and gently adjust downward.
If the return inlets cannot be pointed downward, then you MUST install Baracuda return line diverters. They are available through your Baracuda dealer (see page 16).
FOR POOLS WITH RETURN INLET
DIRECTIONAL FITTINGS
Replace the directional eyeball with Baracuda retrofit eyeball return line diverter
(Part #90153 for
11/2" return lines;
Part #90155 for
2" return lines), and reinstall eyeball retaining ring (see pg. 16).
IF UNABLE TO ADJUST RETURN INLETS
OR FOR POOLS WITHOUT RETURN INLET
DIRECTIONAL FITTINGS
Use Baracuda universal return line diverter
(Part #24100). Pinch wires together and insert fully into return inlet.
5
STEP 2 - ASSEMBLY
FINNED DISC INSTALLATION
Slide the finned disc over the foot pad. Be sure it fits properly in the grooves provided.
The fins on the disc face upward.
Bottom View
FLOWKEEPER™
In single skimmer installations the Flowkeeper ™ Valve MUST BE used. The pool pump provides more gallon per minute flow than your Baracuda ® G3 ™ requires. That's why we provide a way to regulate the flow. The Flowkeeper ™ Valve is self adjusting and provides a by-pass, so that the pool pump and the Baracuda G3 run properly.
Skimming action is maintained through a bypass throat in the valve. As the filter collects debris, the valve automatically maintains the correct flow to the cleaner. The Flowkeeper valve comes preset at the two (2) setting. The lower the number, the lower the flow to the cleaner head. Should readjustment become necessary, pull the adjustment handle to raise or lower the setting.
There are three total setting options. The red tab on the valve can be used to keep the bypass open. In most cases, locking open the by-pass will cause the cleaner to stop.
Rear View
6
FINS FACE
UPW
ARD
POOL PULSE
™
The Pool Pulse ™ is a flow meter that measures the volume of water flowing through your Baracuda ® G3 ™ cleaner. It must be used to properly set the flow on wall vacuum and dual skimmer installations and can be used as a diagnostic tool when the cleaner isn't running properly.
Always use the Pool Pulse ™ with the proper hose length for your pool. Keep the end of the hose underwater, remove the cleaner head, submerge the Pool Pulse ™ and attach it to the end of the hose. The blue indicator door should move into the clear wedge area indicating a flow in the ideal range.
If the flow is in the low range, review the preparation procedures (page 5). A dirty pool filter, clogged baskets and improperly set valves are usually the main cause of low flow. Other types of hydraulic problems may require a professional pool repairman.
If the flow is in the high range, review the installation procedures. The Flowkeeper™ valve must be used on single skimmer installations to maintain ideal flow. With dual skimmer or wall vacuum installations, confirm that the valves controlling these lines are properly set. Slightly open the main drain if necessary.
IDEAL TOO HIGH TOO LOW
7
STEP 3 - HOSE ASSEMBLY
FOR CORNER OR END INSTALLATIONS
If your skimmer or wall vacuum fitting is located at the corner or end of your pool, use enough hose sections to reach the farthest point in the pool, plus one (1) section.
SKIMMER / WALL
VACUUM FITTING
SKIMMER / WALL
VACUUM
FITTING
FOR CENTER INSTALLATIONS
If your skimmer or wall vacuum fitting is located at the center of your pool, use enough hose sections to reach the farthest point in the pool, plus two (2) sections.
SKIMMER / WALL
VACUUM FITTING
SKIMMER / WALL
VACUUM FITTING
Note: You may not use all or you may need more hose sections, with either installation method, depending upon your pool size.
STEP 4 - BALANCE
Your Baracuda ® G3 ™ came with a hose weight, which will compensate for the buoyancy of the hose. A properly balanced hose will create a 45-degree angle from the cleaner head and the bottom of the pool.
Slide the hose weight on the female end of the first section of hose and position it half way up from the cleaner head. See Adjustments (page 13) for additional information.
8
STEP 5 - CHOOSE INSTALLATION
ONE SKIMMER
Turn the filtration system off.
Using the parts shown below, choose a fitting combination best suited for your skimmer.
You may have parts left over.
Do not install in the skimmer at this time.
A
Example 1 Example 2
(1) FlowKeeper™
Valve
C
B
(1) Universal
Valve Cuff
D
D
E
A
B
E
C
E
B
D
A
(1) Hose protector net (1) 4 1 /
2
" Connector
(2) 45° installation adapter elbows
TWO SKIMMERS
No FlowKeeper ™ Valve required
DEDICATED VAC LINE
No FlowKeeper ™ Valve required
C
Insert the end of the hose into the universal valve cuff.
Insert the male end of the hose into the large end of the 45˚ elbow.
Important: To help prevent suction entrapment accidents, wall vacuum fittings should have a safety vac lock installed. Contact your builder or retail pool professional for details
9
STEP 6 - FOR ALL INSTALLATIONS
Turn on the filtration system.
Fill the hose with water by placing the end over a return inlet.
10
Submerge the Baracuda ® G3 ™ pool cleaner head. When bubbles stop coming from the extension pipe, attach the cleaner head to the female end of the hose.
STEP 6 CONTINUED - INSTALLATION
ONE SKIMMER
HOSE PROTECTOR
FLOWKEEPER™
VALVE
4 1 /
2
" CONNECTOR
UNIVERSAL VALVE CUFF
Remove the skimmer basket, attach the regulator valve combination to the hose and install into the skimmer. Turn on the filtration system. Your installation is now complete.
TWO SKIMMERS DEDICATED VAC LINE
Remove the skimmer basket from the deep end skimmer. Attach the cuffed hose end to the suction port of the skimmer. Continue to STEP 7.
Insert the small end of the 45˚ elbow into vac lock and angle the 45˚ elbow toward the pool surface. Continue to STEP 7.
11
STEP 7 - INSTALLATION
FOR POOLS WITH TWO SKIMMERS
AND FOR POOLS WITH DEDICATED VAC LINES
Remove the cleaner head. Attach the
Pool Pulse ™ to the end of the hose.
Keep the Pool Pulse ™ under water.
Turn on the filtration system.
12
For pools with two skimmers, leave the selected skimmer open and slowly close the other skimmer until the blue indicator of the Pool Pulse ™ range (when viewed from the side).
falls into the ideal
For pools with a wall vacuum fitting, leave the wall vacuum fitting fully open and slowly close the skimmer valve until the blue indicator of the Pool Pulse ™ falls into the ideal range (when viewed from the side).
Vacuum and skimmer valves are located at your plumbing manifold.
Remove the Pool Pulse ™ . Submerge the cleaner head.
When the bubbles stop coming from the extension pipe, attach the hose end. Your installation is now complete.
SAMPLE PLUMBING MANIFOLD
IDEAL TOO HIGH TOO LOW
NOTE: Plumbing manifolds vary by pool. Refer to your pool builder for questions regarding your plumbing manifold configuration.
ADJUSTMENTS
Balance - Pools that are 8 1/2 Feet or Deeper
An additional hose weight (PN W43260) may be necessary to balance the Baracuda ® G3 ™ cleaner head.
If the Baracuda G3 is not balanced correctly in the deep end of the pool, (as shown below) turn off the pump, add a second hose weight (approximately 4 to 7 feet) away from the first weight. Place the
Baracuda G3 in the deep end, turn on the pump and determine whether the correct balance has been achieved. If not, re-position the second hose weight accordingly. Additional hose weights may be purchased from your Baracuda G3 dealer if required.
Improving Coverage
Normally it is undesirable for the return line water flow to affect the natural movement of the Baracuda
G3 hose. However, the following illustration shows how return line pressure can be used to balance cleaning coverage or to guide the cleaner away from step areas with “V” shaped corners.
A return line located anywhere along the shaded area can be utilized to gently push the hose allowing the Baracuda G3 to free itself from inpool obstacles.
Technique
Position the return line directional so that you can only detect water movement on the surface
8 feet out from the wall, and aim it at the center of the opposite wall.
13
CARE AND MAINTENANCE
To maintain quality performance and increase the lifespan of your Baracuda ® following:
G3 ™ , please do the
1. The skimmer basket, pump basket and pool filter should be thoroughly cleaned on a regular basis.
Always disconnect the hose from the skimmer before backwashing.
2. NEVER COIL THE HOSE when the cleaner is removed from the pool. A coiled hose can be straightened with hot water or by laying it on a warm pool deck for several hours.) X
INCORRECT
3. REMOVE THE BARACUDA G3 BEFORE SUPER CHLORINATING OR ADDING POOL
CORRECT
CHEMICALS. Reinstall the Baracuda G3 when the imbalance is corrected or after a minimum of 4 hours from super chlorination.
4. Periodically inspect parts for wear. The footpad and disc are the most critical. When the depth of the channels between the treads of the footpad are 1/8" or less, replace the footpad.
To remove the foot flange (PN W69527) unthread and remove the cassette (Steps 1 & 2). Holding the
Baracuda G3 as shown (Step 3), press down on the yellow clip while pulling the foot flange toward you.
Pull off the old footpad and stretch on the new one. Insert the locking clip of the foot flange into the large opening (Step 4), push forward to lock into place (Step 5) insert the cassette and tighten (Step 6).
Step 1 Step 2 Step 3
Step 5
14
Step 4 Step 6
CARE AND MAINTENANCE
Quick Access Cassette System
Foreign objects, such as children’s toys, tree branches and rocks, should be removed manually from your pool prior to operating your Baracuda ® G3 ™ . If a blockage should occur, the Quick Access Cassette
System will allow you to check the diaphragm for damage and remove the blockage in minutes at poolside.
Step 1 Step 2 Step 3
Step 4 Step 5
Unscrew cassette (Step 1) and remove from head (Step 2). Loosen swivel pipe (Step 3). Pull out diaphragm
& inner pipe (Step 4). Pull diaphragm from inner pipe (Step 5) and inspect for blockage or cuts. Remove blockage and rinse. Do not use sharp objects as damage to diaphragm may occur. Contact technical service at
1-888-786-7797 for an authorized warranty station for parts replacement.
Step 6 Step 7 Step 8
Step 9 Step 10
To reassemble: Be sure retaining ring is on diaphragm, push diaphragm onto inner pipe (Step 6). Insert inner pipe into diaphragm chamber and seat diaphragm against lip (Step 7). Tighten cassette assembly (Step 8).
Insert cassette into head (Step 9) and tighten handnut (Step 10).
15
16
ACCESSORIES
1
PART ILLUSTRATION
3A
4
5A
6
2
3B
5B
PART NO.
1. W24000
2. W24100
3A. W90153
(for 1 1 /
2
" return inlet)
3B. W90155
(for 2" return inlet)
4. W26705
DESCRIPTION
Ladder Guard
Always use on stainless steel in-pool ladders
Return Line Diverter
Use when no other return inlet directional fittings exist.
(see page 6).
Retrofit Eyeball Return
Line Diverter
Use to replace standard directional inlet eyeballs
(see page 6).
The with 4 1 /
2
"
Hose Connector
Use when heavy debris or leaf situations exist.
Wheel Deflector
Adapter
5A. W33411
5B.
W41721
6. W43260
7. W38031
Additional 37g Hose Weight
May be required to properly balance the Baracuda G3 cleaner head.
Hide-A-Hose
Sinks the pool cleaner hose when the pump is turned off.
7
PROBLEM
Baracuda ® G3 ™ stops & starts
TROUBLESHOOTING
SOLUTION
Check diaphragm for blockage or damage. Adjust worn diaphragm by loosening cassette swivel, gently pushing down on inner pipe & retightening cassette swivel. Use Pool Pulse to determine proper flow.
Baracuda G3 is patterning Add return diverters or divert return inlets downward.
Lay hose in a straight line in the sun to relax memory.
Confirm proper hose length - add 1 to 2 hose sections.
Baracuda G3 isn't covering opposite end of pool
Baracuda G3 stuck at steps
Baracuda G3 stuck under ladder
Add return diverters or divert return inlets downward.
Use flow to move cleaner to opposite end. Move hose weight away from cleaner head slightly. In deep pools add additional weight.
Utilize return flow (see adjustments). Confirm proper hose length. Adjust flow to cleaner. Adjust hose weight.
Purchase wheel deflector & adapter.
Install ladder guard (PN W24000).
Baracuda G3 flips over
Baracuda G3 won't climb walls
Contact tech services for local warranty station.
Cleaner may not climb walls of some vinyl pools. Use
Pool Pulse ™ and raise flow. Confirm proper hose length.
Adjust hose weight.
Baracuda G3 doesn't move
Baracuda G3 won't leave edge or rim of pool
Solar blanket installation
Use Pool Pulse ™ to insure proper flow. Clean baskets & filter. Check diaphragm for damage. Check hose sections for leaks by lifting each section above water.
Use Pool Pulse ™ to lower flow. Utilize return flow to move cleaner. Adjust hose weight.
Coverage will be limited due to blanket.
Note: In cold water of 60˚ or less, water flow through the Baracuda G3 must be increased to compensate for the reduced flexibility of the hose and diaphragm.
IF ASSISTANCE IS REQUIRED, CALL 1-888-786-7797
17
7
8
19 20
21
22
23
18
9
PARTS DIAGRAM
10
5
6
11
13
2
16
17
3
4
18
1
12
14
15
PART NO.
DESCRIPTION
1.
W69541 Left G3 Main Body
2.
W69542 Right G3 Main Body
3.
W56124 Float - Baracuda G3
4.
W41079 Weight - Baracuda G3
5.
W69545 Retaining Collar - Baracuda G3
6.
W69559 Cassette Chambers Upper and Lower
7.
W69698 G3 Long Life Diaphragm
8.
W81600 Retaining Ring
9.
W56525 Inner Ext. Pipe - Natural 1
10.
W69540 Cassette Outer Extension Pipe w/ Handnut 1
1
1
11.
W74000 Compression Ring
12.
W69732 Foot Flange
13.
W69526 Bumper Fin - Baracuda G3
14.
W72880 Foot Pad - Teal
1
1
1
1
QTY.
1
1
1
1
1
1
15.
17.
W46666
W33160
Finned Disc - Teal
16.
W60050 FlowKeeper ™ Valve
4 1/2" Connector - Aqua
18.
W44800 Pool Pulse ™
19.
W22425 45º Elbow
20.
W63900 Inground Valve Cuff
21.
W33800 Hose Protector Net
22.
W43260 Hose Weight - Aqua 37G.
23.
W83140 Long-Life Hose Kit - 12x1 Meter - Aqua 1
2
1
1
1
1
1
1
1
LET US HELP! BARACUDA
®
G3
™
If you are having a coverage problem you cannot solve, mail or fax us the following information along with a sketch of your pool shape indicating the location of all skimmers, vacuum lines, inlets, stairs, ladders, swimouts, spas, waterfalls, filter systems or other significant features and a brief description of the problem.
MAIL TO: ZODIAC POOL CARE, INC.
2028 N.W. 25th Avenue, Pompano Beach, FL 33069 or fax to: (954) 935-8279
CUSTOMER NAME: ____________________________________________ TELEPHONE NO.: ( _______ ) ___________________
ADDRESS: __________________________________________________________________________________________________
CITY: STATE/PROVINCE: ___________ ZIP/POSTAL CODE: _______________
SERIAL NO.: __________________________________________________ PURCHASED FROM: __________________________
POOL SURFACE (circle one): CONCRETE VINYL FIBERGLASS OTHER: ______________________________________
POOL SIZE: ___________________________________________________ PUMP SIZE (H.P.): _____________________________
FILTER (circle one): SAND D.E.
CARTRIDGE FILTER SIZE (or Model No.) _____________________
INDICATE PROBLEM: _______________________________________________________________________________
___________________________________________________________________________________________________
___________________________________________________________________________________________________
___________________________________________________________________________________________________
___________________________________________________________________________________________________
W83117
ZODIAC POOL CARE, INC.
2028 N.W. 25th Avenue
Pompano Beach, FL 33069
1-888-786-7797 www.zodiacpoolcare.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project