Baumatic | BDI681 | User manual | Baumatic BDI681 User manual

Baumatic BDI681 User manual
BDI681 60 cm Fully
integrated full height
electronic dishwasher
USER MANUAL FOR YOUR BAUMATIC
BDI681 60 cm Fully
integrated full height electronic
dishwasher
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 09/01/09
2
Contents
Environmental note
4
Important safety information
5–7
Specifications
Product and aperture dimensions
Product specifications
Energy efficiency details
Electrical details
8-9
8
8
8
9
Description of the appliance
Control panel
9 - 10
10
Using your dishwasher
Before first use
Filling with dishwasher salt
Setting the water softener level
Filling with rinse aid
Setting the rinse aid level
Filling with dishwasher detergent
Loading the upper basket
Adjusting the upper basket
Loading the lower basket
The cutlery basket
Loading dishes and cutlery
10
10
11
12
13
13
14
15
15
17
18
18
Program table
Setting a wash program
Changing a wash program
At the end of a wash program
The 3 in 1 wash program
The auto program
Setting a delay start
Rinse air and salt indicator neons
20
20
21 - 22
22
22 – 23
23
23 - 24
24
Cleaning and maintenance
The filter system
Cleaning the filters
Cleaning the spray arms
Cleaning the control panel
Cleaning the door
25 - 29
25
26
27
27
28
Error code failure system
General troubleshooting
28 – 29
30 – 31
Installation
Aperture requirements
Installation stages
Preparing and connecting the furniture door
Adjusting the tension of the door spring
Connecting to the mains water supply
Connecting to the water outlet
Connecting to the power supply
Applying the condensation strip
Positioning the dishwasher
Levelling the appliance
Securing the dishwasher
Before first use
32
32
33
33
35
36
37
37
38
39
40
41
41
Contact details
42
- 19
– 12
- 14
- 16
- 19
- 41
– 35
- 38
- 39
3
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.
General Safety
o Repairs to your appliance must only be carried out by a
Baumatic engineer or one of its authorised service agents. Any
attempt by an inexperienced person to repair the appliance,
could result in injury or damage to your dishwasher.
o If you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base area is damaged. As this could
allow access to the internal components of the machine.
o The appliance should be turned off and isolated from the mains
supply, before either cleaning or maintenance work is attempted.
o The mains cable must not be used to pull the plug out of the
electrical socket.
o The machine should not be sprayed with water.
o The external surface of the appliance may become hot whilst
your dishwasher is in use.
o It is possible for small animals to chew either mains cables or
water hoses, which could cause an electric shock hazard.
Installation
o The installation instructions contained within this user manual
should be followed.
o It is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
o Before the first use of the appliance, you should follow the
steps listed in the “Before first use” section on page 10
and page 41 of this manual.
5
o Care should be taken not to trap the power supply cable
underneath the appliance whilst installing it.
o No attempt should be made to alter or modify the specifications
of this appliance.
In daily use
o This appliance is only designed to wash normal domestic
washloads. If you use your dishwasher in any other way or it is
incorrectly used, then Baumatic accepts no liability for any
damage that might be caused and any guarantee will be void.
o It is recommended that the appliance is unplugged and the
water supply is turned off after the machine is used.
o The detergents, rinse aid and salt that you place in this appliance
should be suitable for automatic dishwashers. With regards to
dosage levels, the detergent manufacturer’s recommendations
should be followed.
o Sharp knifes or ones with long blades are a potential safety
hazard when placed in an upright position in the cutlery basket.
We would recommend that these items are placed horizontally in
the upper basket.
o You should not wash any items that have come into contact
with corrosive, acidic or alkaline chemicals, paint, petrol, iron or
steel debris.
o You should not open the door whilst the appliance is set on a
wash program. Depending on which stage that the wash
program is at, hot water could escape the machine.
o You should not leave the door of the appliance open, unless
you are loading or unloading the dishwasher.
o You should not stand or sit on the door when it is open.
6
Child Safety
o Your dishwasher should only be used by adults. You should not
allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
o It could be possible for a child or pet to gain access to the
dishwasher if the door is left open. Therefore please check the
inside of the appliance before setting it on a wash cycle.
o Any packaging that is removed from the machine should be kept
away from children.
o All detergents should be kept out of children’s reach in a safe
place.
o Some water will remain inside the dishwasher when it has
completed a wash cycle. This water is not suitable for drinking
and may contain residues from the detergents that are used in
the appliance.
Declaration of conformity
This appliance complies with the following European Directives:
-73/23 dated 19/02/1973 Low Voltage Directive and subsequent
modifications.
-89/336 dated 03/05/1989 Electromagnetic Compatibility Directive and
subsequent modifications.
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your dishwasher is
located on the right hand side of the drop down door.
Model Number
……………………………….
Serial Number
……………………………….
Date of Purchase
.
……………………………….
7
Specifications
Product dimensions
Height:
Width:
Depth:
820 - 850 mm
595 mm
540 mm
Aperture dimensions
Height:
Width:
Depth:
820 mm (min)
600 mm
570 mm (min)
Product specifications
o 12 Place settings
o 9 functions:
Normal
Intensive
Economy
Glass
Rinse
Rapid
Soak
3 in 1
Auto-sensor
o 5 Wash temperatures: 40°C, 45°C, 50°C, 55°C, 70°C
o 5 Rinse temperatures: 45°C 50°C, 55°C, 65°C, 70°C
o
o
o
o
o
o
o
o
o
o
o
Delay timer
LED display
Self-cleaning stainless steel microfilter
Electronic aqua stop
Anti-leak device
Anti-flood device
Concealed heating element
Height adjustable upper basket
Collapsible plate racks
Adjustable feet
Turbo drying
o
o
o
o
3 in 1 wash program
Auto wash program
Quiet operation (46 dB)
Low water consumption (12 litres)
8
Energy efficiency details
Energy efficiency class:
A
Washing performance class: A
Drying performance class:
A
Electrical details
Rated voltage:
230 Vac 50 Hz
Supply connection:
13 A (double pole switched fused outlet with
3 mm contact gap)
Optional extra
o DWD600SS- Stainless steel door with mark resistant coating
Description of the appliance
1)
2)
3)
4)
5)
6)
Upper basket
Spray arms
Lower basket
Water softener
Main filter
Detergent dispenser
7)
8)
9)
10)
11)
12)
Cup shelf
Cutlery basket
Coarse filter
Rinse aid dispenser
Drain pipe connector
Inlet pipe connector
9
Control panel
1)
2)
3)
4)
5)
6)
7)
ON/OFF button
Power on neon
Delay start button
LED display
Rinse aid and salt indicator neons
Program selection button
Program indicator neons
Using your dishwasher
Before first use
o Install the appliance as per the installation instructions contained
within this booklet.
o Fill the water softener with 1 litre of tap water and then fill with
specialist dishwasher salt. After this you should set the water
softener level.
o Fill the rinse aid dispenser and then set the rinse aid dosage.
10
Filling with dishwasher salt
IMPORTANT: You should only use salt that is specially
designed for use in a dishwasher. If any other type of salt is
used in the appliance (in particular table salt), it will damage
the water softener.
o Ideally you should fill the water softener with salt, just before
you are about to run a wash program. This will help to clear any
salt that may have overflowed from the water softener during
the salt filling process.
o Open the door of the dishwasher and then remove the lower
basket. The basket should be empty when you remove it.
o Turn the water softener cap
anticlockwise and remove it.
o Pour 1 litre of water into the water
softener container.
IMPORTANT: It is only necessary to do this when you fill
the container with salt for the first time.
o Pour salt into the water softener, using
the funnel that is supplied with the
appliance. You should add
approximately 1.2 kg of salt into the
water softener container.
o It is perfectly normal for a small amount of water to come out of
the water softener container, whilst you are filling it with salt.
This does not mean that the container is filled with the correct
amount of salt.
o Refit and fully tighten the water softener cap.
o The salt required warning light will go out approximately 2-6
hours after you have filled the water softener with salt. When
the salt indicator neon lights on the control panel, then you
should follow the filling with dishwasher salt procedure again.
11
o IMPORTANT: You do not need to pour 1 litre of water into
the container when you subsequently fill the water
softener with salt.
Setting the water softener level
It is possible to regulate the amount of salt that the water softener will
release during a wash cycle. The water softener should be set to a
level that is appropriate for the hardness of your water (please refer to
the table below).
To alter the amount of salt that is released by the water softener, you
should:o Remove the lower basket and unscrew the cap from the salt
container.
o Locate the ring with an arrow on it that is located on the salt
container. (See figure below).
o When you first receive your appliance, the arrow
will be pointing to the minus symbol. Using the
water hardness chart, you should turn the arrow
to the setting that is appropriate for your water
hardness.
o The “middle” selector position is halfway between the minus and
plus symbols.
o IMPORTANT: If you are using 3 in 1 dishwasher tablets and live
in a medium or hard water area, then you should still fill the
water softener with salt. The water softener arrow should be
turned to the minus setting.
12
Filling with rinse aid
The rinse aid is released during the final rinse and it helps
to prevent water from forming droplets on your dishes.
These droplets will lead to spots and streaks being left on
items after the wash program has completed.
o Your dishwasher is designed to utilise liquid rinse aid.
o The rinse aid dispenser is located inside the drop down door,
next to the detergent dispenser.
o To access the rinse aid dispenser,
you should turn the cap anticlockwise
and it will pop out of the hole. Then
slowly pour in liquid rinse aid, the
rinse aid dispenser will hold
approximately 140 ml of rinse aid.
o You should continue to fill with rinse aid, until the level indicator
turns completely black.
o Be careful not to overfill the dispenser, as this could cause
oversudsing when a wash program is selected. Wipe away any
rinse aid excess or spillages with a damp cloth.
o Replace the cap and turn it clockwise until it locks into position.
o You should refill the rinse aid dispenser when the rinse aid
indicator neon lights on the control panel.
o IMPORTANT: If you are using 3 in 1 dishwasher tablets then
you should still fill the rinse aid dispenser.
Setting the rinse aid level
The amount of rinse aid that the dishwasher requires also depends on
the hardness of your water. You should experiment with the rinse aid
setting, until you find a level that gives the best results.
o On the first wash cycle, we would recommend
that the rinse aid level is set to number 2.
o If you get water spots and poor drying
performance, then you should turn the arrow
anticlockwise and increase the setting to the next
number.
13
o You should continue to adjust the rinse aid level upwards until
you get no water spots.
o If you get cloudiness or streaking on your dishes, the rinse aid
level is set too high and it is causing foaming during the wash
cycle. Turn the arrow clockwise and lower the setting to the next
number.
Filling with dishwasher detergent
The detergent dispenser must be refilled at the start of each wash
cycle (apart from the Rinse wash program).
o Open the lid that closes over the detergent dispenser and place
the detergent inside of the dispenser.
o The section marked 1 in the diagram is for the main wash cycle
detergent. Only one detergent tablet should be placed in the
dispenser at any one time. If you are using detergent powder or
liquid, you should follow the detergent manufacturer’s
recommendations.
o The section marked 2 in the diagram can have separate
detergent placed in it for any wash cycle that has a pre-wash
element to it, however this is optional. This must be a liquid or
powder detergent, not another detergent tablet.
o Shut the detergent dispenser lid and position the clip on the
outer edge, so that it holds the lid shut.
o At the beginning of a wash cycle the clip will open and the
tablet/powder/liquid will enter the dishwasher.
14
Loading the upper basket
The upper basket is most suited to washing delicate and light
dishware, such as glasses, coffee & tea cups, saucers, plates, bowls
and shallow pans (that are not heavily soiled).
1.
2.
3.
4.
5.
6.
7.
Cups
Small serving bowl
Large serving bowl
Glasses
Saucers
Dish
Dessert dishes
o You should position the dishes and cookware in such a way that
they are not moved by the spray of water during the wash cycle.
o Use the diagram above as a guide to the most appropriate way
to load the upper basket.
Adjusting the upper basket
Your dishwasher has an adjustable upper basket which you can alter to
the most suitable position for the items you are going to wash in the
upper basket.
The height of the upper basket can be adjusted by pulling the handle
on either side of the basket upwards until it clips into place.
Position 1 (upper position)
o For accommodating items such
as glass tumblers and wine
glasses. Wine glasses should be
placed upside down, so that the
stem of the glass rests in one of
the grooves on the side flap.
15
Position 2 (lower position)
o For accommodating additional
tumblers, cups and mugs. You
can also place small, espresso
sized cups on top of the side
racks. Care should be taken to
make sure that there is enough
clearance between the top of the
cups placed on top of the side
racks and the underneath of the
dishwasher interior.
o Please note that when the basket
is in the upper position, you
cannot have the side flaps in a
raised position. Otherwise the
basket will not slide back into the
interior of the dishwasher.
With upper
basket raised
With upper
basket lowered
Maximum height of
dishes (upper basket)
19 cm
24 cm
Maximum height of
dishes (lower basket)
30 cm
25 cm
IMPORTANT: Care should be taken to make sure that the spray
arms can move freely when items have been loaded into the
baskets.
IMPORTANT: Care should be taken when placing long
stemmed glassware, such as champagne glasses in the
upper basket. If they are not positioned correctly, then
there is a risk that they may topple over when the upper
basket is pushed in our pulled out.
16
Loading the lower basket
The lower basket is most suited to washing larger and more heavily
soiled items, such as saucepans, saucepan lids and serving dishes. You
can also load bowls and a variety of plates into the lower basket.
7.
8.
9.
10.
11.
Dessert dishes
Serving plate
Dinner plates
Side plates
Cutlery basket
o Saucepans and serving bowls must always be placed with their
bases upwards.
o Deep saucepans should be slanted, to allow water to run off.
o The bottom rack has prongs at the rear of the basket that can be
folded downwards, to allow for easier loading of larger
saucepans and serving bowls.
17
The cutlery basket
Cutlery should be placed inside of the cutlery basket. The cutlery
basket should then be placed in the appropriate position in the lower
basket.
1.
2.
3.
4.
5.
6.
7.
8.
Forks
Soup spoons
Dessert spoons
Teaspoons
Knives
Serving spoon
Gravy ladle
Serving fork
o For the best washing
performance, cutlery should be
placed through the slots in the top
of the cutlery basket.
IMPORTANT: Do not allow items of cutlery to fall through
the bottom of the cutlery basket, as this may cause
damage to the spray arm and/or the cutlery. If the bottom
of the basket begins to deteriorate and allows items to fall
through, you should replace the cutlery basket.
Loading dishes and cutlery
Household cloths, sponges or any other object that
may absorb water SHOULD NOT be washed in a
dishwasher.
o Remove leftovers and soften the remnants of burnt food in pans,
prior to loading dishes in the appliance.
o Once the dishwasher has been loaded, check that the spray arms
can move freely. If the spray arm comes into contact with any
item, then you should rearrange the wash load.
o Cups, glasses, pans etc should all be loaded with their bases
upwards, so that water does not collect inside of them.
o Cutlery and dishes should not cover each other; otherwise you
may get poor wash results.
18
o Do not allow glasses to touch inside the dishwasher, otherwise
damage may occur.
o Small objects can be placed inside of the cutlery basket.
The following items are NOT suitable for washing
inside a dishwasher:o Cutlery with a handle of mother-of-pearl, wood, horn or china.
o Plastic items that are not resistant to heat.
o Cutlery that consists of glued parts that are not resistant to heat.
o Cutlery items or crockery that are bonded.
o Copper or pewter items.
o Lead crystal glass.
o Wooden platters.
o Synthetic fibre items.
The following items are not always suitable for
washing inside a dishwasher:o Stoneware should only be washed if the manufacturer of the
item has marked it as dishwasher safe.
o Plastic items (such as lunchboxes) should only be washed if the
manufacturer has marked it as dishwasher safe.
o Glazed crockery may fade with repeated washing inside of a
dishwasher.
o Items made of silverware or aluminium can discolour when
washed inside a dishwasher.
o Any food residue should be removed from silver items
immediately, as this can also result in discolouration.
o Certain types of glass may become dull or cloudy after a large
number of washes.
19
Program table
Program
Program
information
Auto
For all types of soil
level, such as
pots, pans,
casserole dishes
and dishes that
have been sat
with dried food on
them for awhile.
For normally
soiled loads, such
as pots, plates,
glasses and lightly
soiled pans.
Standard daily
cycle.
For the heaviest
soiled loads, such
as pots, pans,
casserole dishes
and dishes that
have been sat
with dried food on
them for awhile.
For normally
soiled loads, such
as pots, plates,
glasses and lightly
soiled pans.
Standard daily
cycle.
For lightly soiled
loads, such as
plates, glasses,
bowls and lightly
soiled pans.
For dishes that
need to be rinsed
and dried only.
For lightly soiled
loads, such as
glasses, crystal
and fine china.
3 in 1
Intensive
Normal
(IECEN
50242)*
Eco
Rinse
Glass
Rapid
Soak
A shorter wash for
lightly soiled loads
that do not require
drying.
To rinse dishes
that you plan to
wash later in the
day.
Description Detergent
of cycle
pre/main
Water
consumption
(litres)
Pre-wash
(40°C)
Autowash
Rinse
Rinse (70°C)
Drying
3 in 1 tablets
(or 5/25 g)
11 – 14.5
Pre-wash
Wash (50°C)
Rinse
Rinse (70°C)
Drying
3 in 1 tablets
12.5
Pre-wash
(55°C)
Wash (70°C)
Rinse
Rinse (50°C)
Drying
5/25 g
16
Pre-wash
Wash (50°C)
Rinse
Rinse (65°C)
Drying
5/25 g
11.5
Pre-wash
Wash (45°C)
Rinse
Rinse (55°C)
Drying
Wash (45°C)
Rinse (70°C)
Drying
Pre-wash
Wash (45°C)
Rinse
Rinse (55°C)
Drying
Wash (40°C)
Rinse (45°C)
25 g
11.5
-
6
20 g
11.5
20 g
8
Pre-wash
-
3
* Normal is the testing program for EN 50242.
20
Setting a wash program
Make sure that the before first use section has been
followed.
o Check whether the appliance needs rinse aid or salt adding to it.
o Pull out the top and bottom baskets, then load them in
accordance with the loading instructions.
o Push the top and bottom baskets fully back into position.
o Add detergent
o Switch on the appliance by using the ON/OFF button.
o IMPORTANT: Wait for 5 seconds before pressing the
program selection button, otherwise the appliance may
not function correctly.
o Press the program selection button to choose an appropriate
wash program for the load that you are washing. The relevant
program indicator neon will light to show which wash program
you have selected.
o Select any program options that you want to use (e.g. delay
start).
o Close the door firmly, so that you hear the door lock click shut.
o After a few seconds, you will hear the appliance begin to fill with
water and the wash program will have started.
o If you open the door during the wash program, the wash cycle
will stop. When you close the door again, after 10 seconds, the
wash cycle will restart.
Changing the wash program
o Open the door slightly and then wait a few seconds.
o Press and hold down the program selection button for 3 seconds
to cancel the wash program. Then use the program selection
button to choose the correct wash program.
o Select any program options that you want to use (e.g. delay
start).
21
o Close the door firmly, so that you hear the door lock click shut.
o After a few seconds, you will hear the appliance begin to fill with
water and the wash program will have started.
At the end of a wash program
o The time display will flash for 8 seconds and a buzzer will sound.
o If you have used the delay start mode, the time display will flash
for 8 seconds but the buzzer will not sound.
o Open the door of the appliance.
o Use the ON/OFF button to switch the dishwasher off and unload
the dishwasher.
The 3 in 1 wash program
Make sure that the water softener has been filled with salt
and that the water softener has been set to its lowest
setting.
Make sure that the rinse aid dispenser has been set to an
appropriate level.
THIS WASH PROGRAM MUST BE SELECTED IF YOU ARE USING 3
IN 1 DETERGENT. IF YOU USE ANY OTHER WASH PROGRAM
WITH 3 IN 1 TABLETS, THEN YOU MAY GET POOR WASH
RESULTS.
o Hang the 3 in 1 tablet container on the underneath of the upper
basket, in the position shown on the diagram.
22
o Check that the 3 in 1 tablet container is not going to foul the
upper spray arm, by rotating the spray arm around slowly. If it
does hit the 3 in 1 tablet container, you should move it.
o Put a 3 in 1 tablet inside the 3 in 1 tablet container. Load the
appliance as normal and select the 3 in 1 wash program.
If your wash results are poor, then we would recommend
that you use a dishwasher detergent that doesn’t have
rinse aid and salt included in the tablet. The water softener
should then be adjusted to an appropriate level for the
hardness of the water in your area.
The auto program
This programme is able to analyze the level of soiling on the dishes
and adjust the length of the wash programme, water consumption and
energy level accordingly.
When this wash program is used, a sensor will detect the amount of
soiling contained in the water and make adjustments to the wash
program. These adjustments will depend on whether the items are
lightly soiled or heavily soiled.
Setting a delay start
It is possible to delay the start of the wash program for up to a
maximum of 24 hours.
o Check whether the appliance needs rinse aid or salt adding to it.
o Pull out the top and bottom baskets, then load them in
accordance with the loading instructions.
o Push the top and bottom baskets fully back into position.
o Add detergent
o Turn the appliance on by using the ON/OFF button.
o IMPORTANT: Wait for 5 seconds before pressing the
program selection button, otherwise the appliance may
not function correctly.
o Press the program selection button to choose an appropriate
wash program for the load that you are washing. The relevant
program indicator neon will light to show which wash program
you have selected.
23
o Press the delay start button and you will see the amount of time
that you are delaying the wash program by, appear in the LED
display.
o Close the door firmly, so that you hear the door lock click shut.
o Once the period of time that you set has passed, the dishwasher
will start the wash program that you selected.
Rinse aid and salt indicator neons
o The rinse aid and salt indicator neons on the
control panel will let you know when the
appliance needs rinse aid or salt adding to it.
neon indicates that you need to add rinse aid to the
o The
appliance. You should follow the procedure outlined on page 13.
o The
neon indicates that you need to add dishwasher salt to
the appliance. You should follow the procedure outlined on page
11.
24
Cleaning and maintenance
IMPORTANT: The appliance should be disconnected
from your mains supply before commencing any
cleaning process.
The filter system
Your appliance is fitted with three levels of filtering; these are located
in the base of the dishwasher for ease of access.
1)
Main filter
2)
Coarse filter
3)
Fine filter
Main filter-
Food and soil particles are trapped by this filter and
pulverised by a special jet on the lower spray arm.
This debris is then washed down the drain.
Coarse filter-
Larger items such as pieces of bone or glass, which
could clog the drain, are trapped in this filter.
Fine filter-
This filter holds soil and food residue in the sump
area and prevents it from being redeposited on the
dishes during a wash cycle.
IMPORTANT: Whilst the filtering system is efficient, your
dishwasher is not a waste disposal unit. All items being
washed inside of the dishwasher should have food scraps
removed from them before being loaded into the appliance.
25
Cleaning the filters
For best performance and results, the entire filter assembly should be
thoroughly cleaned regularly (ideally after each wash cycle).
1. Turn the coarse filter
anti-clockwise and then
lift it upwards. Rinse out
this section under a tap
to remove any food
debris that remains in it.
2. Pull out the main filter
and rinse this under the
tap to remove any food
debris that is trapped in
it.
3. Pull out the fine filter and
rinse this under the tap
to remove any food
debris that is trapped in
it.
4. Place the fine filter back in its original position.
5. Place the main and coarse filter back into their original positions
in the base of the dishwasher. You must turn the coarse filter
clockwise to lock it back into position.
IMPORTANT: THE DISHWASHER SHOULD NEVER BE
SET ON A WASH CYCLE WITHOUT THE FILTERS BEING
INSIDE OF THE APPLIANCE.
26
Cleaning the spray arms
The spray arms should be cleaned regularly, to prevent hard water
deposits from clogging the spray arm jets and bearings.
o To remove the spray arm, unscrew the nut and take out the
washer that sits on top of the spray arm.
o Gently pull upwards to remove the spray arm.
o Wash the spray arm in warm, soapy water and use a soft brush
to clean the jets.
o Rinse the spray arm thoroughly and then reassemble the spray
arm back in its original position.
Cleaning the control panel
IMPORTANT: Do not use any abrasive cleaner or household polish on
either the control panel or operating parts.
o Wipe over the control panel using a brand new damp cloth with
warm water.
27
Cleaning the door
o To clean the edge around the outside of the door, you should use
a soft, damp cloth only.
o To prevent water from penetrating the door lock or electrical
components, DO NOT use a spray cleaner of any kind.
o DO NOT use any abrasive cleaner or scouring pads on the inner
or outer surfaces, as they may cause damage to them.
E1
o Longer than expected fill time or drain time.
9 Check the water pressure of your mains water supply.
9 Clean the mesh filter that sits in the inlet hose.
9 Ensure that the inlet hose is not kinked or crushed.
9 Make sure the water tap that the machine is connected to is turned
on fully.
9 Check that the outlet hose is not kinked or crushed and that it’s
positioned correctly (as per the installation instructions).
E4
o The machine has sensed water in the base.
9 Check that the outlet hose is not kinked or crushed.
9 Check that there are no blockages in the drain hose or the drainage
system that the appliance is connected to.
9 The drain pipe may be placed in too high a position or incorrectly.
Check the installation instructions and ensure that the installation is
correct.
E8
o Open or short circuit
9 Motorised valve
o Once you have taken action to rectify the problem that has
caused the fault code to appear, plug the machine back into your
mains power supply.
o Turn the machine on using the ON/OFF button and wait for 5
seconds.
o Press and hold down the delay start button and the ON/OFF
button, until the appliance switches off.
28
o Wait for 5 seconds, and then switch back on the appliance using
the ON/OFF button.
o Wait for a further 5 seconds before attempting to set a wash
program, using the program selection button.
IMPORTANT: If any other fault code appears in the
display window, you should not attempt to clear it yourself
and contact the Baumatic Service Department.
IF THE FAULT CODE REAPPEARS AFTER FOLLOWING
THE ABOVE ADVICE AND CLEARING THE FAULT
CODE. YOU SHOULD TURN OFF THE APPLIANCE;
DISCONNECT THE APPLIANCE FROM YOUR MAINS
SUPPLY. THEN ARRANGE FOR AN ENGINEER TO
ATTEND THE APPLIANCE. YOU SHOULD CONTACT
BAUMATIC SERVICE ON TELEPHONE NUMBER (0118)
933 6911.
IF AN ENGINEER ATTENDS DURING THE GUARANTEE
PERIOD AND FINDS THAT A FAULT HAS BEEN
CAUSED BY AN ITEM ON THE ERROR CODE LIST,
WHICH COULD HAVE BEEN CLEARED BY THE
CUSTOMER. THEN YOU MAY BE LIABLE FOR THE
COST OF THE SERVICE CALL.
29
General troubleshooting
PROBLEM
Dishwasher
doesn’t
run
POSSIBLE
CAUSES
Fuse blown or the
circuit breaker has
tripped
Power supply is not
switched on
WHAT TO DO
Replace the fuse or reset the circuit
breaker. Remove any other
appliances that are sharing the same
circuit with the dishwasher.
Make sure that the dishwasher is
turned on and that the door is closed
securely.
Make sure that the power cord is
fully plugged into the wall socket.
Water pressure is low
Drain pump
doesn’t stop
Overflow
Noise
Some audible sounds
are normal
Suds in the
tub
Stained tub
interior
Dishes are not
fully dried
Check that the water supply is
connected properly and that the
water is turned on.
The system is designed to detect an
overflow. If it does, then it will run
the drain pump continuously when
there is power to the appliance.
You will get a level of operating
noise during a wash cycle, in
particular when food is being
removed from items and when the
detergent dispenser places the tablet
into the tub.
Utensils are not
secure in the baskets
or something small
has dropped into the
basket
Ensure that everything is loaded as
per Baumatic’s loading instructions.
Motor hums
If the dishwasher is not going to be
used for a period of time, then you
should make sure that the appliance
is set on a wash program once a
week. Otherwise the seal around
motor may dry out and cause noise.
Improper detergent
use
Ensure that you are not using 3 in 1
detergent tablets, in conjunction
with rinse aid and salt.
Spilled rinse aid
Always wipe up any excess rinse aid
or rinse aid spillages immediately.
Detergent with
colourant was used
Rinse aid dispenser is
empty
Use a detergent without colourant.
Make sure that the rinse aid
dispenser is filled with rinse aid.
30
Dishes and
pans are not
clean
Improper program
Select a more intense wash
program.
Improper loading
Make sure that the spray arms and
the detergent dispenser are not
being impeded by large dishes.
Spots and
filming on
glasses and
pans
Extremely hard water
Low inlet
temperature
Improper loading
Improper detergent
Incorrect salt/rinse
aid levels
Steam
A normal
phenomenon
You may get a small amount of
steam coming through the vent by
the door latch, during drying and
water draining.
Black or grey
marks on
dishes
Aluminium utensils
have rubbed against
dishes
Use a mild abrasive cleaner to
eliminate the marks. Make sure that
the appliance is loaded correctly in
future.
Water
standing in the
bottom of the
tub
This is normal
A small amount of clean water in the
base of the appliance is not
something to be concerned about.
Dishwasher
leaks
The rinse aid
dispenser is
overfilled or rinse aid
has been spilt inside
the appliance
Take care not to overfill the rinse aid
dispenser. Spilt rinse aid could cause
oversudsing and lead to overflowing.
Wipe away any spills immediately
with a damp cloth.
Dishwasher isn’t
level
Make sure that the dishwasher is
level.
Refer to the relevant sections of this
booklet, to ensure that the
detergent, salt and rinse aid levels
are set correctly. Ensure that the
appliance is loaded correctly.
31
Installation
IMPORTANT: THIS INSTALLATION MUST BE
COMPLETED BY A SUITABLY QUALIFIED PERSON.
BAUMATIC ONLY SANCTION THE INSTALLATION
GIVEN IN THIS INSTRUCTION MANUAL. YOU
SHOULD DISPOSE OF ALL PACKAGING IN AN
ENVIRONMENTALLY FRIENDLY MANNER.
Aperture requirements
o The aperture that your dishwasher needs to be installed into
should resemble the one in the drawings above.
o There should be less than a 5 mm gap between the top of the
dishwasher and the underneath of the worktop.
32
Installation stages
1.
2.
3.
4.
5.
6.
7.
8.
9.
Preparing and connecting the furniture door.
Adjusting the tension of the door spring.
Connecting to the mains water supply
Connecting to the water outlet
Connecting to the power supply
Applying the condensation strip
Positioning the dishwasher
Levelling the dishwasher
Securing the dishwasher
Preparing and connecting the furniture door
o IMPORTANT: The furniture door is not supplied with the
appliance. You should purchase one to match with the rest of
your kitchen cabinets.
o The maximum weight of the furniture door should be 5.5
kilograms. The maximum thickness of the furniture door
should be 15 mm.
o Use the installation template supplied with the appliance to mark
up and then drill out the necessary holes in the furniture door.
33
o Attach the
upper hooks
onto the
furniture door.
o Attach the lower
hooks onto the
furniture door.
o Lift the furniture door towards the dishwasher door, ensuring
that the upper and lower hooks locate into the slots on the
outside of the dishwasher door.
o Push the furniture door downwards so it locks into place on the
dishwasher door.
o Open the
dishwasher door
and find the
covers that are
located on
either side of
the outer edge.
o Fully tighten the
screws into the
holes. Make
sure that you
screw them
tightly into the
furniture door.
34
o IMPORTANT: You should make sure that the screws
supplied are appropriate for the thickness of your
furniture door.
o Replace the covers.
Adjusting the tension of the door spring
o The door of the dishwasher is
attached to springs. These
are set at the factory to
ensure that they are at the
proper tension, so that the
door can open and close
smoothly.
o After the furniture door has been adjusted, you will need to
adjust the tension of the door spring.
o Using an Allen key, rotate the adjusting screw to either tighten
or slacken the steel cable.
o The doors’ spring tension is correct when:a) The door remains in horizontal when in the fully opened
position.
b) You are able to shut the door easily, by raising the door using
your fingers.
o WARNING: If you do not adjust the tension of the door spring,
then it could cause damage to the appliance.
35
Connecting to the mains water supply
IMPORTANT: Do not connect the appliance to your mains
water supply using an old or an existing water inlet hose.
The inlet hose supplied with the dishwasher is the ONLY one
that should be used.
DO NOT CONNECT THE WATER INLET HOSE TO A HOT
WATER TAP.
o The inlet hose will be located inside the cabinet of the dishwasher.
o Connect the water inlet hose to a threaded water tap that has a
3/4” thread and to the inlet hose connector on the appliance.
o Fully tighten the inlet hose to the water tap and the dishwasher.
IMPORTANT: The inlet hose is fitted with an aqua
stop. This MUST be fitted in the upright position, as
shown in the above diagram.
36
Connecting to the water outlet
9 Secure the drain hose, so that it cannot move whilst the
dishwasher is in use.
9 Place the end of the drain hose on your drain pipe. Push it a
short way down into your drain pipe.
9 IMPORTANT: Do not insert the drain hose too deeply into the
pipe, as this may cause siphoning.
9 NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL
LENGTH.
Connecting to the power supply
9 IMPORTANT: The electrical socket must still be accessible
once the appliance is installed.
37
9 Consult the rating plate, located on the right hand side of the
drop down door BEFORE making the electrical connections.
Ensure that the voltage reaching the plug is the same as that on
the rating plate.
9 DO NOT REMOVE THE RATING PLATE AS THE
INFORMATION ON IT IS IMPORTANT.
9 The moulded plug that is supplied with the appliance must be
placed into an earthed and insulated socket.
9 Broken or damaged power leads must only be replaced by a
suitably qualified person. A power lead of a similar type must be
used in replacement.
9 Power lead type – H 0 V V – F 3G 1,5.
9 IMPORTANT: We do not recommend that this appliance is
connected to an extension lead.
Applying the condensation strip
o The condensation strip must be fitted to the underside of the
worktop to protect it against the ingress of moisture. The strip
will deflect steam that rises from your appliance, away from the
underneath of the worktop.
38
o The condensation strip will be located inside of your dishwasher.
o Ensure that the underneath of the worktop is clean before
sticking the strip to it.
o Separate the backing paper away from the strip.
o Stick the condensation strip to the underneath of the worktop.
o IMPORTANT: Failure to attach the condensation strip could
result in damage to your worktop.
Positioning the dishwasher
o Place the feet of the dishwasher into the slide rails.
o Carefully slide the dishwasher back into position, underneath the
worktop.
39
Levelling the appliance
o IMPORTANT: Your dishwasher must be level for it to operate
properly.
o Make sure that the dishwasher is supported whilst it is
being levelled, otherwise it may tip over.
o The rear feet can be
adjusted by using the
adjusting screw at the
front of the appliance.
o The front feet can be
adjusted using a
spanner.
o Use a spirit level to check that the
appliance is level.
o Check that the appliance is level from side
to side.
o Check that the appliance is level from
front to back.
40
Securing the dishwasher
o The dishwasher must be secured to the worktop, this can be
done in one of two ways:o Standard worktop- Secure the dishwasher to the
underside of the worktop by using two wood screws.
o You should screw through the holes in the brackets at the
top of the dishwasher cabinet.
o These screws should be fully tightened.
o Marble/granite worktop- The material of the worktop
will mean that it is impossible to put a screw through the
underneath of the worktop.
o On either side of the front edge of the dishwasher cabinet,
there is a rubber stopper. You should remove the rubber
stoppers, to reveal a pre-drilled hole on either side of the
dishwasher.
o Secure the dishwasher to the cupboard either side of it, by
screwing a wood screw through the pre-drilled holes into
the cupboards. These screws should be fully tightened.
o The rubber stoppers should then be refitted into their
original position.
Before first use
You should check the following before using the appliance for the first
time:That
That
That
That
That
That
That
salt.
o That
o
o
o
o
o
o
o
the dishwasher is level and fixed in position.
the water tap is fully open.
there are no leaks at either end of the drain or inlet hoses.
the inlet and outlet hose are fully tightened.
the inlet and outlet hoses are not kinked.
the power is switched on.
the water softener has been filled with 1 litre of water and
the rinse aid dispenser has been filled.
41
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Czech Republic
Baumatic CR spol s.r.o.
Amperova 495
46215, Librec
Czech Republic
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Service Telephone
(0118) 933 6911
Service Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
www.baumatic.cz
E-mail:
sales@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Republic of Ireland
01- 6266 798
+420 800 185 263
Slovak Republic
Baumatic Slovakia, s.r.o.
Skultetyho 1
831 04 Bratislava 3
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Janderstrasse 9
Mannheim, 68199
Germany
+4962 112 9190
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Caltana 129
Campodarsego (Padova), 35011
Italy
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Grindzuigerstraat 22
1333 MS ALMERE
The Netherlands
+3136 549 1555
www.baumatic.nl
42
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising