x Priomat Elastic Primer 3304 Transparent

x Priomat Elastic Primer 3304 Transparent
Technical Data Sheet – 201.0
Priomat®
Elastic Primer 3304 Transparent
GENERAL
DESCRIPTION
A universal, one component adhesion promoter for all normal plastic vehicle parts.
The products referenced herein may not be available for sale in your market. Please
consult your distributor for product availability.
MIXING
COMPONENTS
Priomat® Elastic Primer 3304 Transparent
MIX RATIO
Ready-to-spray
APPLICATION VISCOSITY
Approximately 12 seconds at 68°F/20°C, DIN 4
POT LIFE
Unlimited (in a sealed container)
SPECIAL TIPS
1. Do not allow Permahyd® Plastic Cleaning Paste 7081 to dry on the surface of the plastic
substrate.
2. Thoroughly clean and scuff all surfaces of the plastic part, paying special attention to all
edges.
3. For hard to reach areas of the plastic part, use the application brush that is included
with the Permahyd® Plastic Cleaning Paste 7081.
4. Permahyd® Plastic Cleaning Paste 7081 is designed for raw plastic and is not suitable
for cleaning painted surfaces.
5. Always use a clean scuff pad.
6. Soft plastic may require a finer scuff pad.
DIFFICULT TO CLEAN PLASTICS MAY NEED TO BE CLEANED MORE TIMES, OR IF
APPLICABLE THE PLASTIC MAY BE BAKED FOR A MINIMUM OF 15 MINUTES AT
140°F (60°C). SOME OEM PLASTIC BUMPERS DO NOT RECOMMEND A BAKE
CYCLE. ONCE THE PLASTIC HAS COOLED, REPEAT THE PROCEDURE BELOW FOR
PREPARING RAW PLASTICS BEGINNING WITH STEP 2.
APPLICATION
SUBSTRATES
All raw plastic parts commonly found on vehicle exteriors (Examples: PP, PP/EPDM, ABS,
SAN, PC, PA, PUR-RIM, R-TPU, TPO, PBTP, UP-GF).
Not recommended for pre painted substrates.
Page 1 of 3
Technical Data Sheet – 201.0
SURFACE PREPARATION
Primed Plastic
Perform a solvent test to check if primer is reversible.
1. If the primer is reversible, then strip and treat as raw plastic.
2. If the primer is not reversible
a. Wash with soap and water, clean with Permaloid® Silicone Remover 7010
Slow, Permahyd® Silicone Remover 7085, or Permahyd® Silicone Remover
7096. Sand primer (with P500-800 when dry sanding or with P600-800 when
wet sanding). Make sure to scuff all of the edges and hard to reach areas with
a gray or gold scotch pad.
b. Re-clean with Permaloid® Silicone Remover 7010 Slow, Permahyd® Silicone
Remover 7085, or Permahyd® Silicone Remover 7096.
c. Apply Priomat® Elastic Primer 3304 Transparent as per below and recoat with
an elastic Permasolid Primer Surfacer or Sealer.
Raw Plastic
The substrate must be free from release agents.
1. Rinse the raw plastic part thoroughly with water and pre-clean it using Permahyd®
Plastic Cleaning Paste 7081 and a clean gold scuff pad.
2. Continue to clean the raw plastic part another 2 to 3 times using new Permahyd ®
Plastic Cleaning Paste 7081 and a clean gold scuff pad. The supplied brush
should be used with Permahyd® Plastic Cleaning Paste 7081 in hard to reach
areas of the plastic part.
3. Remove all Permahyd® Plastic Cleaning Paste 7081 residue from the plastic by
thoroughly rinsing with clean water.
4. Before further treatment, clean the plastic substrate thoroughly with Permaloid 
Silicone Remover 7010 Slow, Permahyd Silicone Remover 7085, or Permahyd
Silicone Remover 7096.
5. Apply Priomat® Elastic Primer 3304 Transparent as per below and recoat with an
elastic Permasolid Primer Surfacer or Sealer.
SPRAYGUN SETUP
HVLP
Approved Transfer Efficiency
1.3-1.4mm
1.2-1.3mm
Please refer to gun manufacturer and local legislation for proper spray pressure
recommendations.
APPLICATION

Apply 1.5 coats.
RECOMMENDED FILM THICKNESS
Approximately 0.15 mil dry film thickness
Page 2 of 3
Technical Data Sheet – 201.0
DRY TIMES
Drying time at 68°F/20°C:
Approximately 15 minutes
RECOAT
With elastic Permasolid® HS Vario Surfacer 8590 Gray, elastic Permasolid® Spectro Sealer
5450, elastic Permasolid® Spectro Surfacer 5400, elastic Permasolid® HS Premium Surfacer
5310, or elastic Permasolid® 2.1 Surfacer 5157
PHYSICAL PROPERTIES
Coating Category: Primer
Max. VOC (AP): 837 g/l; 7.0 lbs/gal
Max. VOC (LE): 838 g/l; 7.0 lbs/gal
Avg. Gallon Weight: 879.9 g/l; 7.34 lbs/gal
Avg. Weight % Volatiles: 95.2 %
Avg. Weight % Water: 0.0%
Avg. Weight % Exempt Solvent: 0.0%
Avg. Volume % Water: 0.0%
Avg. Volume % Exempt Solvent: 0.0%
Theoretical Coverage: 62.4 sq. ft. @ 1 mil
Theoretical Coverage @ Recommended Film Build: 416 sq. ft
VOC REGULATED AREAS
These directions refer to the use of products which may be restricted or require special
mixing instructions in VOC regulated areas. Follow mixing usage and recommendations in
the VOC Compliant Products Chart for your area.
SAFETY AND HANDLING
For industrial use only by professional, trained painters. Not for sale to or use by the general
public. Before using, read and follow all label and MSDS precautions. If mixed with other
components, mixture will have hazards of all components.
Ready to use paint materials containing isocyanates can cause irritation of the respiratory
organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with
a history of respiratory complaints must not be asked to work with products containing
isocyanates.
Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying
respirator with particulate filters or appropriate ventilation, and gloves.
Any analytical results set forth herein do not constitute a warranty of specific product
features or of the product’s suitability for a specific purpose. All products are sold pursuant
to our general conditions of sale. We hereby disclaim all warranties and representations,
express or implied, with respect to this product, including any warranty of merchantability or
fitness for a particular purpose. This product is protected by patent law, trademark law,
copyright law, international treaties and/or other applicable law. All rights reserved.
Unauthorized sale, manufacturing or use may result in civil and criminal penalties.
Revised: April 2016
Page 3 of 3
©2014, 2016 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement