e.dot+ Electric Guns Product Literature

e.dot+ Electric Guns Product Literature
e.dot+™ Electric Guns
Compact electric guns
precisely dispense
small dots or beads
of hot melt adhesive
at high speeds.
Nordson e.dot+ electric guns:
n
Deliver accurate dot or bead placement
n
Require minimal space for installation and service
n
Install quickly and easily
n
Operate quietly
All-electric e.dot+ guns provide precise, high-speed dot or bead
placement, quiet operation, a long service life and compact size.
The all-electric design eliminates the need for compressed
operating air and dynamic seals and a service life in excess of
200 million cycles means superior productivity and very
infrequent replacement.
A reduced-cavity nozzle and ball and nozzle/seat design provides
consistent dots or beads without stringing or tailing, at a wide
range of line speeds. Manual stroke adjustment allows re-zeroing
of the module after servicing.
A fast-acting coil delivers small dots or beads at fast line speeds
with on-times as low as 0.4 ms, with cycle rates as fast as
1.8 ms*. The module coil connector allows fast replacement with
minimal downtime.
Plug and play connections between the adhesive melter, gun,
driver and small-diameter hose, a removable armature and seat,
and interchangeable nozzles simplify installation and maintenance.
An integrated Saturn filter removes any contaminants from the
adhesive flow path.
*
Dependent on adhesive viscosity
e.dot+™ Electric Guns
Specifications
Maximum Hydraulic Pressure
10,000 kPa (100 bars/1450 psi)
Maximum Operating Pressure
4800 kPa (48 bars/700 psi)
Working Viscosity
1000 cps, max 5000 cps
Cycle Speed
1.8 ms*
Electrical Connections
Quick-disconnect
Operating Temperature
365° F (185° C),
max 392°F (200°C)**
Electrical Requirements
See gun driver specifications
Heating Method
Cartridge heater
Integrated Saturn Filter
200 mesh
For more
information,
speak with your
Nordson
representative
or contact
your Nordson
regional office.
United States
Duluth, Georgia
(800) 683-2314 Phone
(866) 667-3329 Fax
* minimum on-time 0.4 ms viscosity dependent; use e.dot+ application guide.
** dependent on pattern; use e.dot+ application guide.
Gun Driver Specifications
LogiComm®
Control System
LogiComm OEM Gun Driver Board
LogiComm Gun Driver
e driver
Single Box
Capacity
4/8 channels / board
4 channels / board
4/8 channels / board
1 channel
Electrical Service 100-240 VAC,
50/60 Hz
110-230 VAC, 100-240 VAC,
50/60 Hz; 24 VDC 50/60 Hz
170 to 264 VAC,
50/60 Hz
Maximum Gun
Power Capacity
110 Watts 160 Watts total
95 Watts
2 Amps
3 Amps
2 Amps
160 Watts
Input Line Fuses 3 Amps
Trigger Source
Options
NPN or PNP
24 VDC
NPN or PNP
(24 VDC sink/source)
Enclosure Rating IP-30
IP-20
24 VDC and
5 VDC
IP-X4 terminal
IP-20
block version IP-30
connector version
Canada
Markham, Ontario
(800) 463-3200 Phone
(905) 475-8821 Fax
Europe
Erkrath, Germany
(49) 211-9205-0 Phone
(49) 211-254658 Fax
Japan
Tokyo, Japan
(81) 3-5762-2700 Phone
(81) 3-5762-2701 Fax
Asia/Australia/
Latin America
Amherst, Ohio
(440) 985-4797 Phone
(440) 985-1096 Fax
Find us on:
e.dot+ gun top feed
e.dot+ gun side feed
PKL-07-5104
Reissued 10/12
© 2007, 2012 Nordson Corporation
All Rights Reserved.
Printed in U.S.A.
Nordson reserves the right to make
design changes between printings.
Nordson Corporation
11475 Lakefield Drive
Duluth, GA 30097-1511
(800) 683-2314
nordson.com/hotmelt
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising