Marmitek | IP EYE ANYWHERE 10 - ADVANCED | Installation guide | Marmitek IP EYE ANYWHERE 10 - ADVANCED Installation guide

Marmitek IP EYE ANYWHERE 10 - ADVANCED Installation guide
™
IP
EYE
ANYWHERE
P EYE ANYWHER
IP EYE ANYWHERE 241/341
Advanced Installation Guide
20377 / 20110202 • IP EYE ANYWHERE 241/341™
ALL RIGHTS RESERVED MARMITEK ©
Preface
Thank you for purchasing the Marmitek H.264/MPEG4/MJPEG
Day&Night or True Colour Megapixel Network Camera, a
standalone system that can be connected directly to an Ethernet
or Fast Ethernet network.
Equipped with a megapixel CMOS sensor, the camera allows you
to capture a wider field of view with a resolution of up to 1280 x
1024. With support for latest H.264 technology, you can record
streaming video that utilizes high quality H.264 images to your
hard drive, enable motion detection and setup automated e-mail
alerts for security.
With the Infrared LEDs and light sensor on the camera (IPEA 241
only), you can capture clear images even in the dark environment.
Compared to the conventional PC Camera, this camera features a
built-in CPU and web-based solutions that can provide a costeffective solution to transmit the real-time high-quality video
images and sounds synchronously for monitoring. The camera
can be managed remotely, so that you can use a web browser to
access and control it from any desktop/notebook computer over
the Intranet or Internet.
The simple installation procedures and web-based interface allow
you to integrate it into your network easily. With comprehensive
applications supported, the IPEyeAnywhere 241 / 341 is your best
solution for remote monitor, high quality, and high performance
video images.
IPEyeAnywhere 241 / 341TM
1
This Advanced Installation Guide provides you with the
instructions and illustrations on how to use your camera, which
includes:
Chapter 1 Introduction to Your Camera describes the features
of the camera. You will also know the components
and functions of the camera.
Chapter 2 Hardware Installation helps you install the camera
according to your application environment. You can
use this camera at home, at work, at any where you
want.
Chapter 3 Accessing the Camera lets you start using your
camera without problem. The camera can be set up
easily and work within your network environment
instantly.
Chapter 4 Configuring the Camera guides you through the
configuration of the camera using the Web browser on
your PC.
Chapter 5 Appendix provides the specification of the camera
and some useful information for using your camera.
NOTE The illustrations and configuration values in this guide are for
reference only. The actual settings depend on your practical
application of the camera.
2
© MARMITEK
Contents
C H A P T E R 1 ............................................................................................ 5
INTRODUCTION TO YOUR CAMERA ............................................................... 5
1.1
1.2
1.3
1.4
CHECKING THE PACKAGE CONTENTS ...................................5
GETTING TO KNOW YOUR CAMERA......................................6
FEATURES AND BENEFITS ...................................................10
SYSTEM REQUIREMENT.......................................................13
C H A P T E R 2 .......................................................................................... 14
HARDWARE INSTALLATION ......................................................................... 14
2.1
2.2
2.3
INSTALLING THE CAMERA STAND .......................................14
CONNECTING THE CAMERA TO LAN/WLAN .....................15
APPLICATIONS OF THE CAMERA..........................................16
C H A P T E R 3 .......................................................................................... 17
ACCESSING THE CAMERA ......................................................................... 17
3.1
3.2
3.3
USING IPFINDER .................................................................17
ACCESSING TO THE CAMERA ..............................................18
CONFIGURING THE IP ADDRESS OF THE PC ........................21
C H A P T E R 4 .......................................................................................... 22
CONFIGURING THE CAMERA ...................................................................... 22
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
USING THE WEB CONFIGURATION ......................................22
QUICK SETUP ......................................................................23
BASIC SETUP .......................................................................30
NETWORK SETTINGS ...........................................................33
SETTING UP VIDEO & AUDIO ..............................................41
EVENT SERVER CONFIGURATION ........................................46
MOTION DETECT .................................................................52
EVENT CONFIGURATION .....................................................53
TOOLS .................................................................................56
USB ....................................................................................58
INFORMATION .....................................................................60
A p p e n d i x ............................................................................................ 61
A.1 SPECIFICATION ....................................................................61
IPEyeAnywhere 241 / 341TM
3
SAFETY WARNINGS
• To prevent short circuits, this product should only be used inside
and only in dry spaces.
• Do not expose the components to rain or moisture. Do not use
the product close to a bath, swimming pool etc.
• Do not expose the components of your systems to extremely
high temperatures or bright light sources.
• In case of improper usage or if you have altered and repaired the
product yourself, all guarantees expire. Marmitek does not accept
responsibility in the case of improper usage of the product or when
the product is used for purposes other than specified. Marmitek
does not accept responsibility for additional damage other than
covered by the legal product responsibility.
• This product is not a toy. Keep out of reach of children.
• Do not open the product: the device may contain live parts. The
product should only be repaired or serviced by a qualified expert.
• Only connect the adapter to the mains after checking whether
the mains voltage is the same as the values on the identification
tags. Never connect an adapter when it is damaged. In that case,
contact your supplier.
4
© MARMITEK
C HAPTER 1
INTRODUCTION TO YOUR CAMERA
1.1 Checking the Package Contents
Check the items contained in the package carefully. You should
have the following:
5 One IPEyeAnywhere 241 / 341 Network Camera
5 One AC Power Adapter
5 One Camera Stand
5 One External Antenna
5 One Ethernet Cable (RJ-45 type)
5 One Installation CD-ROM
5 One Quick Installation Guide
NOTE Once any item contained is damaged or missing, contact the
authorized dealer of your locale.
IPEyeAnywhere 241 / 341TM
5
1.2 Getting to Know Your Camera
„ Front / Right Panel
h
e
a
g
f
c
b
d
i
a. Infrared LEDs (x6) allow your camera to capture clear image
in a dark environment (IPEA 241 only).
b. Light Sensor is used to trigger on and off the Infrared LEDs
according the environmental light level.(IPEA 241 only)
c. Lens Assembly
6
© MARMITEK
d. USB Port allows you to connect an external USB device. It
provides the power distribution up to 500mA.
e. Internal Microphone allows the camera to receive sound and
voice.
f.
Link LED indicates the camera’s network connectivity with the
flashing green light.
g. Power LED indicates the camera is powered on with the
steady amber light.
h. External Antenna
i.
USB* Unmount Button Is used to remove the connected
USB device safely.
NOTE After long pressing the Unmount button for four seconds, the
Power LED starts flashing. When the Power LED resumes the
steady amber light, you can remove the USB device safely.
IPEyeAnywhere 241 / 341TM
7
„ Rear Panel
m
k
j
o
l
j.
n
DC Power Connector connects the AC power adapter, in
order to supply power to the camera.
k. WPS Button is used to protect your WLAN. Instead of
entering the network name (SSID), your wireless network can
be protected simply by pushing a button.
TIP
For more information of using the WPS button, refer to the
instruction of the Web Configuration, Network >> Wireless >>
WPS Setting.
l.
Reset Button will restart the camera when it is pressed
quickly; when it is pressed and held for five seconds, the
camera will resume the factory default settings.
m. Wireless Antenna Connector is used to attach the external
antenna.
8
© MARMITEK
n. Ethernet Cable Connector connects the network cable,
which supports the NWay protocol so that the camera can
detect the network speed automatically.
o. Audio-out Connector connects an external active speaker.
IPEyeAnywhere 241 / 341TM
9
1.3 Features and Benefits
z
H.264/MPEG4/MJPEG Multi-codec Supported
The IPEyeAnywhere 241 / 341provides you with excellent
images by the H.264/MPEG4/ MJPEG multi-codec
selectable technology, allowing you to adjust image size and
quality, and bit rate according to the networking environment.
z
High Resolution Surveillance
Equipped with a megapixel CMOS sensor, the high
performance camera is designed for your professional
surveillance and security applications. The image resolution
is up to 1280 x 1024.
z
IPEA241: Day & Night Surveillance Supported
The six Infrared LEDs around the standard lens assembly
enable the camera to capture crystal clear images in the dark
environment or at night. When the Light Sensor detects the
environmental light level becomes low, the camera captures the
images in black & white mode using these infrared LEDs.
z
IPEA341: True Colour Camera
The camera has a IR blocking filter to produce accurate colours.
It blocks the transmission of the infrared while passing the
visible.
z
10
Remote Control Supported
By using a standard Web browser or the bundled UltraView
Pro software application, the administrator can easily
change the configuration of the camera via Intranet or
Internet. In addition, the camera can be upgraded remotely
when a new firmware is available. The users are also
allowed to monitor the image and take snapshots via the
network.
© MARMITEK
z
Multiple Profiles Supported
The camera supports multiple profiles simultaneously, so
that you can separately set up different image settings (such
as image quality and frame rate) for the video types of the
camera: H.264, MPEG4, MJPEG, and 3GPP.
z
Flexible Audio Capability
The built-in microphone of the Marmitek IP EyeAnywhere
241 / 341 camera provides on-the-spot audio via the
Internet, allowing you to monitor the on-site voice. In
addition, you can connect an external speaker to the
camera to speak through the camera. (supporting mono
audio only).
z
Supports RTSP
The camera supports RTSP (Real Time Streaming Protocol),
which is a technology that allows you to view streaming
media via the network. You can view the real-time video
with the Quick Time player or RealPlayer. To view the realtime streaming image on your computer, open the Web
browser and enter the RTSP link:
MPEG4 stream: rtsp://(IP address of the camera)/mpeg4
H.264 stream: rtsp://(IP address of the camera)/h264
IPEyeAnywhere 241 / 341TM
11
z
z
z
12
Mobile Device Viewing Supported
The camera supports real time video viewing on your mobile
device. After installing the required software applications,
you can easily monitor the camera’s real-time video from
your iPhone, iPod Touch, or iPad (requires iPhone OS 3.1
or later). The latest Android phone can be supported too.
Multiple Platforms Supported
The camera supports multiple network protocols, including
TCP/IP, SMTP e-mail, HTTP, and other Internet related
protocols. Therefore, you can use the camera in a mixed
operating system environment, such as Windows 2000/XP/
Vista, and Windows 7/8.
Multiple Applications Supported
Through the remote access technology, you can use the
cameras to monitor various objects and places for your own
purposes. For example, babies at home, patients in the
hospital, offices and banks, and more. The camera can
capture both still images and video clips, so that you can
keep the archives and restore them at any time.
© MARMITEK
1.4 System Requirement
z
z
Networking
o LAN:
10Base-T Ethernet or 100Base-TX Fast
Ethernet; Auto-MDIX.
o WLAN:
IEEE 802.11b/g/n
Accessing the Camera using Web Browser
o Platform:
Microsoft® Windows® XP/Vista/WIN 7/8
o CPU:
Intel Pentium III 800MHz or above
o RAM:
512MB
o Resolution:
800 x 600 or above
o User Interface: Microsoft® Internet Explorer 6.0 or above;
Apple Safari 2 or above; Mozilla Firefox
2.00 or above
z
z
Accessing the Camera using UltraView Pro
o Platform:
Microsoft® Windows® XP/Vista/WIN 7/8
o Resolution:
1024 x 768 or above
Hardware Requirement:
o 1 camera:
Intel Pentium 4 2.4GHz; 512MB RAM
o 2~4 cameras: Intel Pentium 4 2.8GHz; 1GB RAM
o 5~16 cameras: Intel Pentium 4 3.4Hz; 2GB RAM
o 17~24 cameras: Intel Core 2 Duo E6400; 1GB RAM
o 25~32 cameras: Intel Core 2 Duo E8400; 2GB RAM
NOTE If you connect multiple cameras to monitor various places
simultaneously, you are recommended to use a computer with
higher performance.
IPEyeAnywhere 241 / 341TM
13
C HAPTER 2
HARDWARE INSTALLATION
2.1 Installing the Camera Stand
The Marmitek IP Eye Anywhere camera comes with a camera
stand, which uses a swivel ball screw head to lock to the camera’s
screw hole. When the camera stand is attached, you can place the
camera anywhere by mounting the camera through the three
screw holes located in the base of the camera stand.
14
© MARMITEK
2.2 Connecting the Camera to LAN/WLAN
Use the provided Ethernet cable to
connect the Marmitek IP Eye
Anywhere camera to your local area
network (LAN).
When you connect the AC power
adapter, the camera is powered on
automatically. You can verify the
power status from the Power LED on
the front panel of the camera.
Once connected, the Link LED starts
flashing green light and the camera is
on standby and ready for use now.
Connecting the Ethernet Cable
If you have the IEA11 or 21 and use a
wireless network in your application
environment, you need to attach the
included external antenna to the
camera.
When the camera is powered on, the
camera will automatically search any
access point with “default” SSID.
Connecting the External Antenna
NOTE If the camera cannot connect to your wireless network, you
need to install the camera in LAN and proceed with WLAN
settings.
IPEyeAnywhere 241 / 341TM
15
2.3 Applications of the Camera
The camera can be applied in multiple applications, including:
z
Monitor local and remote places and objects via Internet or
Intranet.
z
Capture still images and video clips remotely.
z
Upload images or send email messages with the still images
attached.
The following diagram explains one of the typical applications for
your camera and provides a basic example for installing the
camera.
*Please
enclosed by
waterproof housing
when using outdoor
Home Applications of the Internet Cameras
* Please have the camera enclosed by waterproof housing when using in outdoor.
16
© MARMITEK
C HAPTER 3
ACCESSING THE CAMERA
3.1 Using IPFinder
The camera comes with a conveniently utility, IPFinder, which is
included in the Installation CD-ROM, allowing you to search the
camera on your network easily.
1. Insert the Installation CD-ROM into your computer’s CD-ROM
drive to initiate the Auto-Run program.
2. Click the IPFinder item to launch the utility. The control panel
will appear as below.
Display the connected
camera(s). Double click
to link the Camera.
Click About to get the Version information of IPFinder.
Click Link to connect the selected camera.
Click Change IP to modify the IP address of the selected camera.
Click Search to find the IP address of the connected camera(s).
Click Exit to close the utility.
3. Once you get the IP address of the camera, launch the Web
browser or UltraView Pro to access your camera.
IPEyeAnywhere 241 / 341TM
17
3.2 Accessing to the Camera
Whenever you want to access the camera:
1. Since the default configuration of the camera is DHCP mode
enabled, you are recommended to launch IPFinder to search
the IP address that is assigned to the camera by the DHCP
server, and then click Link to access the camera via the Web
browser.
2. If Network Camera can't get IP Address under DHCP mode,
the default IP Address will be 192.168.0.30.
3. When the login window appears, enter the default User name
(admin) and password (admin) and press OK to access to the
main screen of the camera’s Web Configuration.
Enter the User name
and Password.
NOTE If you are initially access to the camera, you will be ask to install a
new plug-in for the camera. Permission request depends on the
Internet security settings of your computer. Click Yes to proceed.
18
© MARMITEK
After you login into the Web Configuration of the camera, the Main
screen will appear as below:
\
X
Y
Z
[
The Main screen of the Web Configuration provides you with
many useful information and functions, including:
X Live View/Setup Switch:
z Click the
button to configure the
camera. For details, see Chapter 4.
button to return to the Main
z Click the
screen to view the live view image.
Y Compression Buttons: Select to transmit and record the
video using H.264, MPEG4 or MJPEG compression.
IPEyeAnywhere 241 / 341TM
19
Z Function Buttons: Use these buttons to control the audio,
video, and trigger functions.
z Manual Record allows you to record and save a video
clip.
z Snapshot allows you to capture and save a still image.
z Browse allows you to assign the destination folder to
store the video clips and still images.
z Talk allows you to speak out through the camera. Please
note only one user is allowed to use this function at a time.
z Listen allows you to receive the on-site sound and voice
from the camera.
[ Live View Area: Displays the real-time video image of the
connected camera.
z The Compression mode is displayed above the Live
View image.
z Click the Zoom buttons (
live view image by 1x, 2x, or 3x.
) to zoom in the
\ Language and Camera Information:
z The Language pull-down menu allows you to select your
favorite displayed language for the system.
z The Camera Information area displays the camera’s
location and the current date & time. The information can
be modified in the Web Configuration.
NOTE If your PC use Microsoft Vista platform, you may not find the
recorded files that are saved by Snapshot or Manual Record. You need
to disable the protected mode of Security in the IE Browser through the
following steps:
1.
2.
3.
4.
20
Open the Internet Explorer browser.
Click Tools > Internet Options.
Click Security.
Disable the Enable Protected Mode option and then click OK.
© MARMITEK
3.3 Configuring the IP Address of the PC
If you are failed to access to the camera, please check the IP
address of your computer. When you connect the camera to your
computer directly to proceed with configuration of the camera, you
need to set up the IP addresses to be in the same segment for the
two devices to communicate.
1. On your computer, click Start > Control Panel to open the
Control Panel window.
2. Double-click Network Connection to open the Network
Connection window.
3. Right-click Local Area Connection and then click Properties
from the shortcut menu.
4. When the Local Area Connection Properties window appears,
select the General tab.
5. Select Internet Protocol [TCP/IP] and then click Properties
to bring up the Internet Protocol [TCP/IP] Properties window.
6. To configure a fixed IP address that is within the segment of
the camera, select the Use the following IP address option.
Then, enter an IP address into the empty field. The suggested
IP address is 192.168.0.x (x is 1~254 except 30), and the
suggested Subnet mask is 255.255.255.0.
7. When you are finished, click OK.
IPEyeAnywhere 241 / 341TM
21
C HAPTER 4
CONFIGURING THE CAMERA
4.1 Using the Web Configuration
You can access and manage the camera through the Web
browser and the provided software application UltraView Pro. This
chapter describes the Web Configuration, and guides you through
the configuration of the camera by using the Web browser.
on the Main
To configure the camera, click
screen of Web Configuration. The Web Configuration will start
from the Basic page.
The Web Configuration contains the settings that are required for
the camera in the left menu bar, including Smart Wizard, My
Android, Basic, Network, Video/Audio, Event Server, Motion
detect, Event Config, Tools, USB, and Information.
22
© MARMITEK
4.2 Quick Setup
4.2.1 Using Smart Wizard
The camera’s Smart Wizard lets you configure your camera easily
and quickly. The wizard will guide you through the necessary
settings with detailed instructions on each step.
To start the wizard, click Smart Wizard in the left menu bar.
Step 1. Camera Settings
Enter the name and
location for the camera.
Enter the administrator
password twice.
IPEyeAnywhere 241 / 341TM
23
Step 2. IP Settings
Select the IP setting
according to your
network: DHCP,
Static IP, or
PPPoE.
24
© MARMITEK
Step 3. Email Settings
Enter the required
information to be
able to send
email with image.
IPEyeAnywhere 241 / 341TM
25
Step 4. Wireless Networking
Enter the required
settings for wireless
networking.
26
© MARMITEK
Step 5. Confirm Settings
Click Apply to finish the
wizard and reboot the
camera.
Click Prev to go back to
the previous step(s) and
change the settings; or
click Cancel to end the
wizard and discard the
changes.
IPEyeAnywhere 241 / 341TM
27
4.2.2 Using My Android
The camera’s My Android wizard lets you set up your Android
mobile and Google services (Google Talk and Picasa) easily and
quickly. The wizard will guide you through the necessary settings
with detailed instructions on each step.
To start the wizard, click My Android in the left menu bar.
Step 1. Setting Up Google Talk Account
Enter the Google
Talk account for
your camera.
Step 2. Setting Up Gmail Account
Enter the Gmail
account for your
camera.
Step 3. Setting Up Picasa Account
Enter the Picasa
account for your
camera.
Step 4. YouTube Settings
Enter the YouTube
account for your
camera.
28
© MARMITEK
Step 5. Confirm Settings
Click Apply to finish the
wizard and reboot the
camera.
Click Prev to go back to
the previous step(s) and
change the settings; or
click Cancel to end the
wizard and discard the
changes.
NOTE Once you have set your Gmail account in step 2, the Email
setting in Event Server Setting will be completed automatically.
For more information, refer to the instruction of the Web
Configuration, Event Server Setting >> Email.
IPEyeAnywhere 241 / 341TM
29
4.3 Basic Setup
The Basic menu contains three sub-menus that provide the
system settings for the camera, such as the Camera Name,
Location, Date & Time, and User management.
4.3.1 Basic >> System
z
30
Basic: This item allows you to assign the camera name and
location information.
- Camera Name: Enter a descriptive name for the camera,
which is helpful to identify the camera easily while multiple
cameras are connected within the network.
© MARMITEK
z
z
- Location: Enter a descriptive name for the location where
is monitored by the camera.
- Language Default: Select your favorite displayed
language for the system.
Indication LED Control: This item allows you to set the
LED illumination as desired. The available options include:
Normal and OFF.
IR LED Control: This item allows you to control the IR LED.
The available options include: Auto and OFF.
When OFF is selected you can select the start and end time
when the IR LEDS have to be off. (IPEA 241 only)
4.3.2 Basic >> Date & Time
z
Date and Time: Enter the correct date and time for the
system.
- TimeZone: Select the proper time zone for the region
from the pull-down menu.
- Synchronize with PC: Select this option and the date &
time settings of the camera will be synchronized with the
connected computer.
- Synchronize with NTP Server: Select this option and the
time will be synchronized with the NTP Server. You need
to enter the IP address of the server and select the update
interval in the following two boxes. (For example
131.155.2.3)
- Manual: Select this option to set the date and time
manually.
4.3.3 Basic >> User
z
Administrator: To prevent unauthorized access to the
camera’s Web Configuration, you are strongly recommend
to change the default administrator password. Type the
administrator password twice to set and confirm the
password.
IPEyeAnywhere 241 / 341TM
31
z
z
General User
- User Name/Password: Enter the user’s name you want
to add to use the camera. Then, enter the password for
the new user.
After entering the User Name and Password, click
Add/Modify to add the new user to the camera. To modify
the user’s information, select the one you want to modify
from UserList and click Add/Modify.
- UserList: Display the existing users of the camera. To
delete a user, select the one you want to delete and click
Delete.
Guest
- User Name/Password: Enter the user’s name you want
to add to use the camera. Then, enter the password for
the new guest.
After entering the User Name and Password, click
Add/Modify to add the new user to the camera. To modify
the user’s information, select the one you want to modify
from UserList and click Add/Modify.
- UserList: Display the existing guests of the camera. To
delete a user, select the one you want to delete and click
Delete.
NOTE The “General User” can access the camera and control the
Function buttons of the camera’s Web Configuration; the
“Guest’ can only view the live view image from the Main screen
of the Web Configuration while accessing the camera. Only the
“Administrator” is allowed to configure the camera through the
Web Configuration.
32
© MARMITEK
4.4 Network Settings
The Network menu contains the networking related settings for the
camera, such as the IP Setting, DDNS Setting, IP Filter, and
Wireless.
IPEyeAnywhere 241 / 341TM
33
4.4.1 Network >> Network
z
IP Setting: This item allows you to select the IP address
mode and set up the related configuration. The default
setting is DHCP mode enabled.
- DHCP: Select this option when your network uses the
DHCP server. When the camera starts up, it will be
assigned an IP address from the DHCP server
automatically.
- Static IP: Select this option to assign the IP address for
the camera directly. You can use IPFinder to obtain the
related setting values.
IP
Enter the IP address of the camera. The
default setting is 192.168.0.30.
Subnet Mask
Enter the Subnet Mask of the camera. The
default setting is 255.255.255.0.
Default
Gateway
Enter the Default Gateway of the camera.
The default setting is 192.168.0.1.
Primary/
Secondary
DNS
DNS (Domain Name System) translates
domain names into IP addresses. Enter the
Primary DNS and Secondary DNS that are
provided by ISP.
- PPPoE: Select this option when you use a direct
connection via the ADSL modem. You should have a
PPPoE account from your Internet service provider. Enter
the User Name and Password. The camera will get an IP
address from the ISP as starting up.
NOTE Once the camera gets an IP address from the ISP as starting
up, it automatically sends a notification email to you. Therefore,
when you select PPPoE as your connecting type, you have to
set up the email or DDNS configuration in advance.
z
34
DDNS Setting: With the Dynamic DNS feature, you can
assign a fixed host and domain name to a dynamic Internet
IP address. To set up the DDNS:
1. Select the Enable option to enable this feature.
© MARMITEK
2. Select the Provider from the pull-down list.
3. Enter the required information in the Host Name,
User Name, and Password boxes.
NOTE You have to sign up for DDNS service with the service provider
before configuring this feature.
z
UPnP: The camera supports UPnP (Universal Plug and
Play), which is a set of computer network protocols that
enable the device-to-device interoperability. In addition, it
supports port auto mapping function so that you can access
the camera if it is behind an NAT router or firewall. Select
the Enable option to enable this feature.
z
Ports Number
- HTTP Port: The default HTTP port is 80.
NOTE If the camera is behind an NAT router of firewall, the suggested
to be used is from 1024 to 65535.
4.4.2 Network >> Network >> Advanced
z
Bonjour: The devices with Bonjour will automatically
broadcast their own services and listen for services being
offered for the use of others. If your browser has Bonjour,
you can find the camera on your local network without
knowing its IP address.
The Apple Safari is already with Bonjour. You can download
the complete Bonjour for Internet Explorer browser from
Apple's web site by visiting http://www.apple.com/bonjour/.
z
RTSP
- RTSP Streaming: Selection the Authentication as
Disable, Basic, or Digest to configure the transmission of
streaming data within the network.
- RTSP Port: The default RTSP Port (Real Time Streaming
Protocol) is 554.
IPEyeAnywhere 241 / 341TM
35
4.4.3 Network >> IP Filter
The IP Filter setting allows the administrator of the camera to limit
the users within a certain range of IP addresses to access the
camera. To disable this feature, select the Disable option;
otherwise, select the Accept option to assign the range of IP
addresses that are allowed to access the camera, or select the
Deny option to assign the range of IP addresses that are blocked
to access the camera.
z
Disable: Select this option to disable the IP Filter function of
the camera.
z
Accept
- IPv4: Assign a range of IP addresses that are allowed to
access the camera by entering the Start IP address and
End IP address options. When you are finished, click
Add to save the range setting. You can repeat the action
to assign multiple ranges for the camera.
- IPv6: Enter the IP Address that is allowed to access the
camera.
z
Deny
- IPv4: Assign a range of IP addresses that are blocked to
access the camera by entering the Start IP address and
End IP address options. When you are finished, click
Add to save the range setting. You can repeat the action
to assign multiple ranges for the camera.
- IPv6: Enter the IP Address that is not allowed to access
the camera.
For example, when you enter 192.168.0.50/192.168.0.80 in
Start/End IP Address of Accept > IPv4, the user whose IP
address located within 192.168.0.50 ~ 192.168.0.80 will be
allowed to access the camera. On the other hand, if you enter the
IP range in Start/End IP Address of Deny > IPv4, the user whose
IP address located within the range will not be allowed to access
the camera.
36
© MARMITEK
4.4.4 Network >> Wireless Setting
The IPEyeAnywhere 241 / 341 supports WLAN while you use the
wireless network. Select the Enable option to enable this feature.
z Wireless
- Network ID (SSID): Keep the default setting of this option
to connect the camera to any access point under the
infrastructure network mode. To connect the camera to a
specified access point, set a SSID for the camera to
correspond with the access point’s ESS-ID. To connect
the camera to an Ad-Hoc wireless workgroup, set the
same wireless channel and SSID to match with the
computer’s configuration.
IPEyeAnywhere 241 / 341TM
37
Click Site Survey to display the available wireless
networks, so that you can easily connect to one of the
listed wireless networks.
List of searching results
- Wireless Mode: Select the type of wireless
communication for the camera: Infrastructure or Ad-Hoc.
- Channel: Select the appropriate channel from the list
when you use an Ad-Hoc connection.
- Authentication: Select the authentication method to
secure the camera from being used by unauthorized user:
Open, Shared-key, WPA-PSK, and WPA2-PSK. The
following table explains the four options:
Open
The default setting of Authentication mode,
which communicates the key across the
network.
Shared-key
Allow communication only with other devices
with identical WEP settings.
WPA-PSK/
WPA2-PSK
WPA-PSK/WPA2-PSK is specially designed
for the users who do not have access to
network authentication servers. The user has
to manually enter the starting password in
their access point or gateway, as well as in
each PC on the wireless network.
If you select Open or Shared-key as the Authentication
mode, you need to complete the following settings:
38
© MARMITEK
Š Encryption: Select the WEP option to enable the data
encryption feature to secure the camera within the
wireless network.
Š Format: Once you enable the Encryption feature, you
need to determine the encryption format by selecting
ASCII or HEX. ASCII format causes each character you
type to be interpreted as an eight-bit value. Hex format
causes each pair of characters you type to be
interpreted as an eight-bit value in hexadecimal (base
16) notation.
Š Key Length: Select the WEP key length you use: 64
bits or 128 bits.
Š WEP Key 1/2/3/4: Enter the WEP key(s) in the following
boxes.
If you select WPA-PSK or WPA2-PSK as the
Authentication mode, you need to complete the following
settings:
Š Encryption: Select TKIP or AES. TKIP (Temporal Key
Integrity Protocol) changes the temporal key every
10,000 packets to insure much greater security than the
standard WEP security. AES (Advanced Encryption
Standard) is used to ensure the highest degree of
security and authenticity for digital information.
Š Pre-Shared Key: This is used to identify each other in
the network. Enter the name in the box, and this name
must match the Pre-shared key value in the remote
device.
IPEyeAnywhere 241 / 341TM
39
4.4.5 Network >> Wireless >> WPS Setting
WPS (Wi-Fi Protected Setup) sets a new standard of Wi-Fi
security, providing a simplified secure network setup solution for
the end users. Once the required settings have been completed,
your wireless network can be protected by simply pressing the
WPS button on the camera.
z
PROTECTED SETUP: Press the Reset to Unconfigured
button to reset the WPS configuration of the camera.
z
WPS
- PIN Mode: The PIN (Personal Information Number) mode
builds the connection by entering the PIN Code directly.
Once you enter the PIN Code of the camera on the router
(or access point) that supports WPS, you can directly
build a WPS connection between the camera and the
device by simply pressing its WPS button.
- PBC Mode: The PBC (Push Button Configuration) mode
builds the connection by scanning the devices in the
wireless network. Once you press the camera’s WPS
button, it starts to scan the WPS devices in the wireless
network, and then you can build the WPS connection by
clicking the Connect button.
z
TIP
40
Device Status: Display the WPS configuration of the
camera.
The Power LED indicates the WPS connection status by:
- blinking 3 times when the connection is built successfully.
- repeating 3 times of short-short-long blink when the
connection is failed.
© MARMITEK
4.5 Setting up Video & Audio
The Video & Audio menu contains four sub-menus that provide
the video and audio settings for the camera.
4.5.1 Video & Audio >> Camera
z
Image Setting
- Brightness: Adjust the brightness level from 0 ~ 100.
- Saturation: Adjust the colours level from 0 ~ 100.
- Sharpness: Adjust the sharpness level from 0 ~ 100.
TIP
Click Default then Apply to restore the default settings of
the three options above.
- Mirror: Select Vertical to mirror the image vertically, or
select Horizontal to mirror the image horizontally.
IPEyeAnywhere 241 / 341TM
41
- Light Frequency: Select the proper frequency according
to the camera’s location to reduce the flicker: 50Hz, 60Hz
or Outdoor.
TIP
When the camera is installed indoors, the Light Frequency
option can be set normally (50Hz or 60Hz). However, the
image of live video might be over exposure if the camera is
focusing on the object outdoors. When this happens, you
can set the option as Outdoor (even when the camera is
installed indoors) to fix over exposure issue.
4.5.2 Video & Audio >> Video
z
H.264
- Video Resolution: Select the desired video resolution
from the four formats: SXGA, VGA, QVGA and QQVGA.
The higher setting (VGA) obtains better video quality while
it uses more resource within your network.
- Video Quality: Select the desired image quality from five
levels: Lowest, Low, Medium, High, and Highest.
- Frame Rate: Select a proper setting depending on your
network status.
z
MPEG4
- Video Resolution: Select the desired video resolution
from the three formats: VGA, QVGA and QQVGA. The
higher setting (VGA) obtains better video quality while it
uses more resource within your network.
- Video Quality: Select the desired image quality from five
levels: Lowest, Low, Medium, High, and Highest.
- Frame Rate: Select a proper setting depending on your
network status.
z
MJPEG
- Video Resolution: Select the desired video resolution
from the four formats: SXGA, VGA, QVGA and QQVGA.
42
© MARMITEK
The higher setting (VGA) obtains better video quality while
it uses more resource within your network.
- Video Quality: Select the desired image quality from five
levels: Lowest, Low, Medium, High, and Highest.
- Frame Rate: Select a proper setting depending on your
network status.
NOTE The camera supports H.264, MPEG4 and MJPEG compression.
Please note that that MJPEG mode captures the images in
JPEG format, which requires higher bandwidth to view smooth
video. You can control the bandwidth of each connection well
through the setting options above. For the bandwidth
information, refer to the Appendix, Bandwidth Reference Guide.
z
3GPP: The camera supports 3GPP specification. Select the
Disable option to disable this feature. Otherwise, select
3GPP Without Audio or 3GPP With Audio to transfer the
video clips without or with audio.
If you use a mobile phone that supports 3GPP, you can also
view the real-time streaming image captured by the camera
on your phone (with the default player on the phone) by
entering the RTSP link: rtsp://(IP address of the
camera)/3gp.
NOTE Your mobile phone and the service provider must support
3GPP function. Please contact your service provider when you
are failed to use this service.
IPEyeAnywhere 241 / 341TM
43
4.5.3 Video & Audio >> Audio
z
Camera Microphone In: Select the Enable option to
enable the camera’s audio function, so that you can receive
the on-site sound and voice from the camera.
z
Camera Speaker Out: Select the Enable option to enable
the camera’s external speaker function, so that the
connected speaker can play the sound and voice through
the camera.
- Volume: Set the speaker’s volume.
4.5.4 Video & Audio >> Overlay / Mask
This sub-menu is used to set the image overlay and mask feature
of the camera.
z
Image Overlay: This item allows you to set the image
overlay.
In the Image File option, click Browse to select the image
file from your computer, and then click Upload. You can
click Preview to check the image size and adjust the image
position before clicking Upload. The preview image area is
displayed with red dotted line. If you want to remove the
preview image before uploading, click Delete.
Since you click Upload, the preview image area is displayed
with white dotted line. Click Enable and set the
transparency setting by whether selecting the Transparent
option or not.
When done, click Apply. You can see the image overlay on
the live view image when you click Live View.
NOTE The width and height of the input overlay graphic should be
multiple of 4 at a maximum size of 43690 pixels, and in JPG or
BMP (24-bit RGB) format.
z
44
Privacy Mask: This item allows you to configure up to two
mask areas.
© MARMITEK
Select the area 1 or 2 from the Window pull-down list, and
then click Enable. You can change the size and position of
the area by holding and dragging the mouse.
You can also change the colour of the mask area by clicking
the Colour box and then selecting the colour you want.
When done, click Apply. You can see the mask area(s) on
the live view image when you click Live View.
4.5.5 Video & Audio >> Overlay / Mask >> Text
Overlay
This page is used to set the text overlay feature of the camera,
including the following three options: date & time, heading text,
and background transparency setting.
z
Include Date & Time: Select this option to display the date
& time information on the live view image.
z
Include Text: Select this option and enter your heading text
in the box to display the text information on the live view
image.
z
Enable Opaque: Select this option to display the overlay
text with a background colour.
For example, when you select the Include Date & Time and
Include Text options and click Apply, you can see the related
information on the live view image when you click Live View.
IPEyeAnywhere 241 / 341TM
45
4.6 Event Server Configuration
The Event Server menu contains six sub-menus that allow you to
upload images to FTP, send emails that include still images, store
the images to a NAS system, send instant message, and upload
the image/video to your Picasa/YouTube account.
When you complete the required settings for FTP, Email, or
Network Storage, click Test to test the related configuration is
correct or not. Once the camera connects to the server
successfully, click Apply.
46
© MARMITEK
4.6.1 Event Server Setting >> FTP
z
FTP
- Host Address: Enter the IP address of the target FTP
server.
- Port Number: Enter the port number used for the FTP
server.
- User Name: Enter the user name to login into the FTP
server.
- Password: Enter the password to login into the FTP
server.
- Directory Path: Enter the destination folder for uploading
the images. For example, /Test/.
- Passive Mode: Select the Enable option to enable
passive mode.
- FTP Upload with: Select upload to FTP with one
snapshot image or a series image in pre-event/post-event
time when event triggered.
NOTE Due to the network environment, the camera may not upload
number of images that you set.
4.6.2 Event Server Setting >> Email
z
Email
- SMTP Server Address: Enter the mail server address.
For example, smtp.com.
- Sender Email Address: Enter the email address of the
user who will send the email. For example,
mymail@mail.com.
- SMTP Port: Assign the SMTP port in the text box. The
default SMTP port is 25. If the mail server requires an
encrypted connection, you should check the SSL option.
- Authentication Mode: Select None or SMTP according
to the mail server configuration.
IPEyeAnywhere 241 / 341TM
47
- Sender User Name: Enter the user name to login the mail
server.
- Sender Password: Enter the password to login the mail
server.
- Receiver #1 Email Address: Enter the first email address
of the user who will receive the email.
- Receiver #2 Email Address: Enter the second email
address of the user who will receive the email.
- Send Email With: Select the attachment type that is to be
added to the email.
NOTE Due to the network environment, the camera may not upload
number of images that you set.
4.6.3 Event Server Setting >> Network Storage
z
48
Network Storage
- Samba Server Address: Enter the IP address of the
Network Storage server. For example, 192.168.1.12
- Share: Assign the folder on the Network Storage server to
share the files to users. For example, share
- Path: Assign the path for uploading the files on the
Network Storage server. For example, Test.
- User Name: Enter the user name to login into the
Network Storage server.
- Password: Enter the password to login into the Network
Storage server.
- Split By: When the file is too large to upload smoothly,
use this option to split it by selecting File Size or
Recording Time.
- When Storage Full: Select Stop Recording or
Recycle – Delete Oldest Folder when the storage space
on the Network Storage server is full.
© MARMITEK
- Encode Format: Select MPEG4 or H.264 as the encode
format while recording.
- File Format: Select MP4 or AVI as the file format while
recording.
NOTE The recorded video files in Network Storage are enclosed by
MP4/AVI format without audio.
4.6.4 Event Server Setting >> Instant Message
The camera supports the Jabber IM service, so that you can send
an instant message once you have a Jabber account. For more
information of Jabber, please visit the Jabber Website at:
http://www.jabber.org/ .
z
Instant Message
- Jabber ID: Enter your user ID to login into the Jabber IM
service.
- Jabber Password: Enter the password to login into the
Jabber IM service.
- Manually Specify Server Host/Port: Select the Enable
option to manually configure the Jabber server settings.
- Jabber Server Address: Enter the Jabber server address
manually.
- Jabber Port: Assign the Jabber port manually in the text
box.
- Encrypt Connection: Select the Enable option to secure
the connection.
- Encrypt Authentication: Select the Enable option to
secure the connection.
- Receiver: Enter the receiver’s information.
- Message: Enter the message that is to be sent.
IPEyeAnywhere 241 / 341TM
49
4.6.5 Event Server Setting >> Picasa Setting
The camera supports the Picasa upload service, so that you can
send the camera’s image to your Picasa account once you have a
Picasa account.
z
Picasa Setting
- User Name: Enter your user name to login into the Picasa
account.
- Password: Enter the password to login into the Picasa
account.
- Privacy: Set the account as Public or Private.
- When Storage Full: Select Stop or Recycle – Delete
Oldest Folder when the storage space on the Picasa
account is full.
4.6.6 Event Server Setting >> YouTube Setting
The camera supports the YouTube upload service, so that you
can send the camera’s video to your YouTube account once you
have a YouTube account.
NOTE
z
50
The USB Flash Disk must be mounted for YouTube upload.
YouTube Setting
- User Name: Enter your user name to login into the
YouTube account.
- Password: Enter the password to login into the YouTube
account.
- Developer Key: Enter the specify developer key if you
have registered the Developer Key for YouTube.
- Source: Enter the source code for YouTube.
- When Upload Fail: Select the retry times (1~10) or
interval time (in minute) to upload video again when
upload is failed.
- Title: Enter a title for the uploaded video.
© MARMITEK
- Description: Enter a description for the uploaded video.
- Keyword: Enter a keyword for the video so that the user
can search the video easily.
- Category: Select a category for the uploaded video.
- Privacy: Set the account as Public or Private.
IPEyeAnywhere 241 / 341TM
51
4.7 Motion Detect
The Motion Detect menu contains the command and option that
allow you to enable and set up the motion detection feature of the
camera. The camera provides three detecting areas.
To enable the detecting area, select Window 1/2/3 from the pulldown list, and then select Enable. When the detecting area is
enabled, you can use the mouse to move the detecting area and
change the area coverage.
z
Name: Assign a name to the detecting area.
z
Threshold: Move the slide bar to adjust the level for
detecting motion to record video.
NOTE Sliding the Threshold bar to the right will decrease the
sensitivity of motion detection; sliding the Threshold bar to the
left will increase the sensitivity of motion detection.
52
© MARMITEK
4.8 Event Configuration
The Event Config menu contains five sub-menus that provide the
commands to configure event profiles.
4.8.1 Event Configuration >> General Setting
z
General
- Snapshot/Recording Subfolder: You can assign a
descriptive name for the subfolder to save the captured
image/video files. Otherwise, leave this option blank to
use the default setting.
- Storage Recording Time Per Event: Limit the recording
time while you are using the Network Storage solution.
IPEyeAnywhere 241 / 341TM
53
4.8.2 Event Configuration >> Arrange Schedule
Profile
z
Schedule Profile: This sub-menu displays the scheduled
profile(s). To customize the profile, click Add and then enter
a descriptive name for the profile in the prompt dialog
window. After entering the profile name, click OK and the
profile is added to the Schedule Profiles list. To delete the
profile, select the profile in the list and click Delete.
- Profile Name: Display the profile name that you select in
the Schedule Profiles list.
- Weekdays: Select the weekday(s) that you want to
separately assign in the schedule profile. The weekday
that has been assigned will be displayed with green colour.
- Time List: Display the time period that you have assigned
within the selected weekday. To assign the same time
period to every weekday, click Copy this to all weekdays;
click Delete this from all weekdays to remove the
selected time period from every weekday. Click Delete to
remove the selected time period.
- Start/End Time: Enter the start and end time and then
click Add to assign a time period within in the selected
weekday.
54
© MARMITEK
4.8.3 Event Configuration >> Motion Detect Trigger
z
Motion Detect Trigger: Select the Enable option to enable
the trigger function of the camera, so that you can send
captured images within the detecting area to the FTP server,
email receiver, or the Network Storage server, etc. You have
to configure corresponding settings, such as FTP server and
email server, to enable this feature. Please note that you
have to configure the related settings before enabling these
features.
- Schedule Profile: Select a schedule profile from the pulldown list.
- Action: Select the destination that the captured images
will be sent to: Record to USB (Upload to YouTube),
Record to Network Storage, Send Email, FTP Upload,
Instant Message, or Upload Image to Picasa.
4.8.4 Event Configuration >> Schedule Trigger
You can separately configure the schedule for trigger function
of the camera by Email, FTP, or Network Storage. Select the
Enable option on each item, and then select a Schedule
Profile from the pull-down list and set the Interval time.
NOTE If the setting value of the Storage Recording Time Per
Event option in General Setting is longer than the Interval
time in Network Storage Schedule, the recorded file will be a
continuous video clip.
For example, if you set the Storage Recording Time Per
Event as 10 seconds and the Interval as 5 seconds,
recorded file becomes a non-stop video clip because the
camera will record a 10-second video clip every 5 seconds.
IPEyeAnywhere 241 / 341TM
55
4.9 Tools
The Tools menu provides the commands that allow you to restart
or reset the camera. You can also backup and restore your
configuration, and upgrade the firmware for the camera.
z
Factory Reset: Click Reset to restore all factory default
settings for the IP EyeAnywhere.
z
System Reboot: Click Reboot to restart the camera just
like turning the device off and on. The camera configuration
will be retained after rebooting.
z
Configuration: You can save your camera configuration as
a backup file on your computer. Whenever you want to
resume the original settings, you can restore them by
retrieving the backup file.
56
© MARMITEK
- Backup: Click Get the backup file to save the current
configuration of the camera.
- Restore: Click Browse to locate the backup file and then
click Restore.
z
NOTE
Update Firmware: You can upgrade the firmware for your
camera once you obtained a latest version of firmware.
- Current Firmware Version: This item displays the
current firmware version.
- Select the firmware: Click Browse to locate the backup
file and then click Update.
Make sure to keep the camera connected to the power source
during the process of upgrading firmware. Otherwise, the
camera might be damaged because of failure of upgrading
firmware.
When this happens, the system will enable the Rescue mode (as
shown below) after the camera reboots, so that you can upgrade
the firmware again.
IPEyeAnywhere 241 / 341TM
57
4.10 USB
The USB menu provides the information and controls of the
connected USB device.
z
USB Dismount: To safely remove the connected USB
device, you can press the Unmount button for four seconds
on the camera or click Dismount from this item.
z
USB Information: Display the Total space and Free space
of the USB device.
z
USB Setting
- Split By: When the file is too large to transfer smoothly,
use this option to split it by selecting File Size or
Recording Time.
58
© MARMITEK
- When Storage Full: Select Stop Recording or
Recycle – Delete Oldest Folder when the storage space
on the USB device is full.
- Encode Format: Set the encode format of the captured
image as MJPEG or H.264.
- File Format: Set the file format of the recorded video as
MP4 or AVI.
- Upload the Recorded file to YouTube: Select the option
to simultaneously upload the recorded video file to the
YouTube account that you have assigned.
-
IPEyeAnywhere 241 / 341TM
59
4.11 Information
The Information menu displays the current configuration and
events log of the camera.
z
Device Info: Display the Basic, Video & Audio, and Network
settings of the camera.
z
System Log: The Logs table displays the events log
recorded by the system.
60
© MARMITEK
Appendix
A.1 Specification
„
Image Sensor
Sensor
Resolution
Min. Illumination
IR blocking filter
True Colour
1/4” Colour Megapixel CMOS Sensor
1280 x 1024
0,5 Lux
IPEA 341
IPEA 341
„
System Hardware
Processor
ARM9 base
RAM
64MB SDRAM
ROM
8MB NOR Flash
Power
DC 12V
Power Consumption 10W max.
„
Lens Assembly
Lens Type
Lens Specification
View Angle
Night vision
IPEyeAnywhere 241 / 341TM
Board Lens
F2.8, 4.0mm
60 degree
940nm IR LED (Switch by light sensor,
manually and schedule control, IPEA
241 )
61
„
„
Video
Compression
Video resolution
Communication
LAN
WLAN
Protocol support
„
„
Audio
Input
Output
Codec
User Interface
LAN
Antenna
USB Port
USB Dismount
Reset
WPS
LEDs
62
H.264/MPEG4/MJPEG
H.264 & MJPEG: SXGA (1280 x 1024)
@ 15fps / VGA (640 x 480) @ 30fps /
QVGA (320 x 240) @ 30fps / QQVGA
(160 x 120) @ 30fps; MPEG4: VGA
(640 x 480) @ 30fps / QVGA (320 x
240) @ 30fps / QQVGA (160 x 120) @
30fps
10/100Mbps Fast Ethernet with AutoMDIX
(for wireless model) IEEE 802.11b/g/n
TCP/IP,IPV6, UDP, ICMP,DHCP client,
NTP, DNS, DDNS, SMTPs, FTP, HTTP,
Samba, UPnP, RTP, RTCP, RTSP
Built-in microphone
Headphone output jack (Mono)
PCM/AMR (AMR is for 3GPP only)
One RJ-45 port
One external antenna
USB 2.0 port, with one unmount button;
Power distribution: 500mA Max.
One USB Dismount button
One Reset button
One WPS button
Power LED (amber); Link LED (green)
© MARMITEK
„
Software
OS Support
Browser
Software
Windows XP/Vista, and Windows 7/8
Internet Explorer 6.0 or above; Apple
Safari 2 or above; Mozilla Firefox 2.00
or above
UltraView Pro for playback/recording/
configuration features
„
Operating Environment
Temperature
Operation: 0qC ~ 45qC;
Storage: -15qC ~ 60qC
Humidity
Operation: 20% ~ 85% non-condensing;
Storage: 0% ~ 90% non-condensing
„
EMI
IPEyeAnywhere 241 / 341TM
LVD, EuP Power report (ERP), FCC/CE
class B
63
A.3
Glossary of Terms
NUMBERS
10BASE-T
100BASE-TX
10BASE-T is Ethernet over UTP Category III, IV, or V
unshielded twisted-pair media.
The two-pair twisted-media implementation of
100BASE-T is called 100BASE-TX.
A
ADPCM
AMR
Applet
ASCII
ARP
AVI
Adaptive Differential Pulse Code Modulation, a new
technology improved from PCM, which encodes analog
sounds to digital form.
AMR (Adaptive Multi-Rate) is an audio data
compression scheme optimized for speech coding,
which is adopted as the standard speech codec by
3GPP.
Applets are small Java programs that can be
embedded in an HTML page. The rule at the moment
is that an applet can only make an Internet connection
to the computer form that the applet was sent.
American Standard Code For Information Interchange,
it is the standard method for encoding characters as 8bit sequences of binary numbers, allowing a maximum
of 256 characters.
Address Resolution Protocol. ARP is a protocol that
resides at the TCP/IP Internet layer that delivers data
on the same network by translating an IP address to a
physical address.
Audio Video Interleave, it is a Windows platform audio
and video file type, a common format for small movies
and videos.
B
BOOTP
Bootstrap Protocol is an Internet protocol that can
automatically configure a network device in a diskless
workstation to give its own IP address.
C
64
© MARMITEK
Communication Communication has four components: sender,
receiver, message, and medium. In networks, devices
and application tasks and processes communicate
messages to each other over media. They represent
the sender and receivers. The data they send is the
message. The cabling or transmission method they
use is the medium.
Connection
In networking, two devices establish a connection to
communicate with each other.
D
DHCP
DNS
Developed by Microsoft, DHCP (Dynamic Host
Configuration Protocol) is a protocol for assigning
dynamic IP addresses to devices on a network. With
dynamic addressing, a device can have a different IP
address every time it connects to the network. In some
systems, the device's IP address can even change
while it is still connected. It also supports a mix of static
and dynamic IP addresses. This simplifies the task for
network administrators because the software keeps
track of IP addresses rather than requiring an
administrator to manage the task. A new computer can
be added to a network without the hassle of manually
assigning it a unique IP address. DHCP allows the
specification for the service provided by a router,
gateway, or other network device that automatically
assigns an IP address to any device that requests one.
Domain Name System is an Internet service that
translates domain names into IP addresses. Since
domain names are alphabetic, they're easier to
remember. The Internet however, is really based on IP
addresses every time you use a domain name the
DNS will translate the name into the corresponding IP
address. For example, the domain name
www.network_camera.com might translate to
192.167.222.8.
E
Enterprise
An enterprise network consists of collections of
IPEyeAnywhere 241 / 341TM
65
network
Ethernet
networks connected to each other over a
geographically dispersed area. The enterprise network
serves the needs of a widely distributed company and
operates the company’s mission-critical applications.
The most popular LAN communication technology.
There are a variety of types of Ethernet, including
10Mbps (traditional Ethernet), 100Mbps (Fast
Ethernet), and 1,000Mbps (Gigabit Ethernet). Most
Ethernet networks use Category 5 cabling to carry
information, in the form of electrical signals, between
devices. Ethernet is an implementation of CSMA/CD
that operates in a bus or star topology.
F
Fast Ethernet
Firewall
Fast Ethernet, also called 100BASE-T, operates at 10
or 100Mbps per second over UTP, STP, or fiber-optic
media.
Firewall is considered the first line of defense in
protecting private information. For better security, data
can be encrypted. A system designed to prevent
unauthorized access to or from a private network.
Firewalls are frequently used to prevent unauthorized
Internet users from accessing private networks
connected to the Internet, especially Intranets all
messages entering or leaving the intranet pass through
the firewall, which examines each message and blocks
those that do not meet the specified security criteria.
G
Gateway
Group
A gateway links computers that use different data
formats together.
Groups consist of several user machines that have
similar characteristics such as being in the same
department.
H
HEX
66
Short for hexadecimal refers to the base-16 number
system, which consists of 16 unique symbols: the
© MARMITEK
numbers 0 to 9 and the letters A to F. For example, the
decimal number 15 is represented as F in the
hexadecimal numbering system. The hexadecimal
system is useful because it can represent every byte (8
bits) as two consecutive hexadecimal digits. It is easier
for humans to read hexadecimal numbers than binary
numbers.
I
Intranet
This is a private network, inside an organization or
company that uses the same software you will find on
the public Internet. The only difference is that an
Intranet is used for internal usage only.
Internet
The Internet is a globally linked system of computers
that are logically connected based on the Internet
Protocol (IP). The Internet provides different ways to
access private and public information worldwide.
Internet address To participate in Internet communications and on
Internet Protocol-based networks, a node must have
an Internet address that identifies it to the other nodes.
All Internet addresses are IP addresses
IP
Internet Protocol is the standard that describes the
layout of the basic unit of information on the Internet
(the packet) and also details the numerical addressing
format used to route the information. Your Internet
service provider controls the IP address of any device
it connects to the Internet. The IP addresses in your
network must conform to IP addressing rules. In
smaller LANs, most people will allow the DHCP
function of a router or gateway to assign the IP
addresses on internal networks.
IP address
IP address is a 32-binary digit number that identifies
each sender or receiver of information that is sent in
packets across the Internet. For example 80.80.80.69
is an IP address. When you “call” that number, using
any connection methods, you get connected to the
computer that “owns” that IP address.
ISP
ISP (Internet Service Provider) is a company that
maintains a network that is linked to the Internet by
IPEyeAnywhere 241 / 341TM
67
way of a dedicated communication line. An ISP offers
the use of its dedicated communication lines to
companies or individuals who can’t afford the high
monthly cost for a direct connection.
J
JAVA
Java is a programming language that is specially
designed for writing programs that can be safely
downloaded to your computer through the Internet
without the fear of viruses. It is an object-oriented
multi-thread programming best for creating applets and
applications for the Internet, Intranet and other
complex, distributed network.
L
LAN
Local Area Network a computer network that spans a
relatively small area sharing common resources. Most
LANs are confined to a single building or group of
buildings.
M
MJPEG
MPEG4
MJPEG (Motion JPEG) composes a moving image by
storing each frame of a moving picture sequence in
JPEG compression, and then decompressing and
displaying each frame at rapid speed to show the
moving picture.
MPEG4 is designed to enable transmission and
reception of high-quality audio and video over the
Internet and next-generation mobile telephones.
N
NAT
68
Network Address Translator generally applied by a
router that makes many different IP addresses on an
internal network appear to the Internet as a single
address. For routing messages properly within your
network, each device requires a unique IP address.
But the addresses may not be valid outside your
network. NAT solves the problem. When devices within
© MARMITEK
Network
NWay Protocol
your network request information from the Internet, the
requests are forwarded to the Internet under the
router's IP address. NAT distributes the responses to
the proper IP addresses within your network.
A network consists of a collection of two or more
devices, people, or components that communicate with
each other over physical or virtual media. The most
common types of network are:
LAN – (local area network): Computers are in close
distance to one another. They are usually in the same
office space, room, or building.
WAN – (wide area network): The computers are in
different geographic locations and are connected by
telephone lines or radio waves.
A network protocol that can automatically negotiate the
highest possible transmission speed between two
devices.
P
PCM
PING
PPPoE
Protocol
PCM (Pulse Code Modulation) is a technique for
converting analog audio signals into digital form for
transmission.
Packet Internet Groper, a utility used to determine
whether a specific IP address is accessible. It functions
by sending a packet to the specified address and waits
for a reply. It is primarily used to troubleshoot Internet
connections.
Point-to-Point Protocol over Ethernet. PPPoE is a
specification for connecting the users on an Ethernet to
the Internet through a common broadband medium,
such as DSL or cable modem. All the users over the
Ethernet share a common connection.
Communication on the network is governed by sets of
rules called protocols. Protocols provide the guidelines
devices use to communicate with each other, and thus
they have different functions. Some protocols are
responsible for formatting and presenting and
presenting data that will be transferred from file server
IPEyeAnywhere 241 / 341TM
69
memory to the file server’s net work adapter Others are
responsible for filtering information between networks
and forwarding data to its destination. Still other
protocols dictate how data is transferred across the
medium, and how servers respond to workstation
requests and vice versa. Common network protocols
responsible for the presentation and formatting of data
for a network operating system are the Internetwork
Packet Exchange (IPX) protocol or the Internet
Protocol (IP). Protocols that dictate the format of data
for transferors the medium include token-passing and
Carrier Sense Multiple Access with Collision Detection
(CSMA/CD), implemented as token-ring, ARCNET,
FDDI, or Ethernet. The Router Information Protocol
(RIP),a part of the Transmission Control
Protocol/Internet Protocol (TCP/IP) suite, forwards
packets from one network to another using the same
network protocol.
R
RJ-45
Router
RTP
RTSP
RJ-45 connector is used for Ethernet cable connections.
A router is the network software or hardware entity
charged with routing packets between networks.
RTP (Real-time Transport Protocol) is a data transfer
protocol defined to deliver live media to the clients at
the same time, which defines the transmission of video
and audio files in real time for Internet applications.
RTSP (Real-time Streaming Protocol) is the standard
used to transmit stored media to the client(s) at the
same time, which provides client controls for random
access to the content stream.
S
Server
SIP
70
It is a simple computer that provides resources, such
as files or other information.
SIP (Session Initiated Protocol) is a standard protocol
that delivers the real-time communication for Voice
over IP (VoIP), which establishes sessions for features
such as audio and video conferencing.
© MARMITEK
SMTP
SNMP
Station
Subnet mask
The Simple Mail Transfer Protocol is used for Internet
mail.
Simple Network Management Protocol. SNMP was
designed to provide a common foundation for
managing network devices.
In LANs, a station consists of a device that can
communicate data on the network. In FDDI, a station
includes both physical nodes and addressable logical
devices. Workstations, single-attach stations, dualattach stations, and concentrators are FDDI stations.
In TCP/IP, the bits used to create the subnet are called
the subnet mask.
T
(TCP/IP)
Transceiver
Transmission Control Protocol/Internet Protocol is a
widely used transport protocol that connects diverse
computers of various transmission methods. It was
developed y the Department of Defense to connect
different computer types and led to the development of
the Internet.
A transceiver joins two network segments together.
Transceivers can also be used to join a segment that
uses one medium to a segment that uses a different
medium. On a 10BASE-5 network, the transceiver
connects the network adapter or other network device
to the medium. Transceivers also can be used on
10BASE-2 or 10BASE-T networks to attach devices
with AUI ports.
U
UDP
The User Datagram Protocol is a connectionless
protocol that resides above IP in the TCP/IP suite
User Name
The USERNAME is the unique name assigned to each
person who has access to the LAN.
Utility
It is a program that performs a specific task.
UTP
Unshielded twisted-pair. UTP is a form of cable used
by all access methods. It consists of several pairs of
IPEyeAnywhere 241 / 341TM
71
wires enclosed in an unshielded sheath.
W
WAN
WEP
Windows
WPA
WPA2
72
Wide-Area Network. A wide-area network consists of
groups of interconnected computers that are separated
by a wide distance and communicate with each other
via common carrier telecommunication techniques.
WEP is widely used as the basic security protocol in
Wi-Fi networks, which secures data transmissions
using 64-bit or 128-bit encryption.
Windows is a graphical user interface for workstations
that use DOS.
WPA (Wi-Fi Protected Access) is used to improve the
security of Wi-Fi networks, replacing the current WEP
standard. It uses its own encryption, Temporal Key
Integrity Protocol (TKIP), to secure data during
transmission.
Wi-Fi Protected Access 2, the latest security
specification that provides greater data protection and
network access control for Wi-Fi networks. WPA2 uses
the government-grade AES encryption algorithm and
IEEE 802.1X-based authentication, which are required
to secure large corporate networks.
© MARMITEK
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising