Denon | AVR-1611 | Owner`s manual | Denon AVR-1611 Owner`s manual

Denon AVR-1611 Owner`s manual
Simple
version
v
Versión sencilla
3
Basic
version
v
Version simplifiée
Version basique
Versión básica
12
AV SURROUND RECEIVER
AVR-1611
Advanced
version
v
Version avancée
Versión avanzada
27
Owner’s Manual
Manuel de l’Utilisateur
Manual del usuario
Information
v
60
“Part names and functions”
(vpage 61)
Informations
“Nomenclature et fonctions“
(vpage 61)
Información
“Nombres y funciones de las
piezas“ (vpágina 61)
ESPAÑOL FRANCAIS ENGLISH
nSAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
CAUTION:
HOT SURFACE. DO NOT TOUCH.
Hot
surface
mark
The top surface over the internal heat sink may become hot
when operating this product continuously.
Do not touch hot areas, especially around the “Hot surface
mark” and the top panel.
PRECAUTION:
IMPORTANT SAFETY
INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
SURFACE CHAUDE. NE PAS TOUCHER.
La surface supérieure du dissipateur de chaleur peut devenir
chaude si vous utilisez ce produit en continu.
Ne touchez pas les zones chaudes, tout particulièrement vers
l’inscription “Hot surface mark” et le panneau supérieur.
PRECAUCIÓN:
SUPERFICIE CALIENTE. NO TOCAR.
La superficie superior sobre el disipador de calor interno
podría llegar a calentarse al operar este producto de forma
continua.
No toque las áreas calientes, especialmente las situadas
alrededor de la “Hot surface mark” y del panel superior.
CAUTION:
FCC INFORMATION (For US customers)
1.PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this product may not cause harmful
interference, and (2) this product must accept any interference received,
including interference that may cause undesired operation.
2.IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modification not expressly
approved by DENON may void your authority, granted by the FCC, to use
the product.
3.NOTE
This product has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This product generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
product does cause harmful interference to radio or television reception,
which can be determined by turning the product OFF and ON, the user
is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the product into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the local retailer authorized to distribute this type of product or
an experienced radio/TV technician for help.
For Canadian customers:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
To completely disconnect this product from the mains, disconnect the plug
from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to the unit
and must be within easy access by the user.
PRECAUTION:
Pour déconnecter complètement ce produit du courant secteur, débranchez
la prise de la prise murale.
La prise secteur est utilisée pour couper complètement l’alimentation de
l’appareil et l’utilisateur doit pouvoir y accéder facilement.
PRECAUCIÓN:
Para desconectar completamente este producto de la alimentación eléctrica,
desconecte el enchufe del enchufe de la pared.
El enchufe de la alimentación eléctrica se utiliza para interrumpir por completo
el suministro de alimentación eléctrica a la unidad y debe de encontrarse en
un lugar al que el usuario tenga fácil acceso.
II
ENGLISH FRANCAIS ESPAÑOL
nNOTES ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO
WARNINGS
AVERTISSEMENTS
ADVERTENCIAS
•Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
•Handle the power cord carefully.
Hold the plug when unplugging the cord.
•Keep the unit free from moisture, water, and
dust.
•Unplug the power cord when not using the unit
for long periods of time.
•Do not obstruct the ventilation holes.
•Do not let foreign objects into the unit.
•Do not let insecticides, benzene, and thinner
come in contact with the unit.
•Never disassemble or modify the unit in any way.
•Ventilation should not be impeded by covering
the ventilation openings with items, such as
newspapers, tablecloths or curtains.
•Naked flame sources such as lighted candles
should not be placed on the unit.
•Observe and follow local regulations regarding
battery disposal.
•Do not expose the unit to dripping or splashing
fluids.
•Do not place objects filled with liquids, such as
vases, on the unit.
•Do not handle the mains cord with wet hands.
•When the switch is in the OFF position, the
equipment is not completely switched off from
MAINS.
•The equipment shall be installed near the
power supply so that the power supply is easily
accessible.
•Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
•Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du cordon.
•Protéger l’appareil contre l’humidité, l’eau et la
poussière.
•Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
•Ne pas obstruer les trous d’aération.
•Ne pas laisser des objets étrangers dans
l’appareil.
•Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
•Ne jamais démonter ou modifier l’appareil d’une
manière ou d’une autre.
•Ne pas recouvrir les orifices de ventilation avec
des objets tels que des journaux, nappes ou
rideaux. Cela entraverait la ventilation.
•Ne jamais placer de flamme nue sur l’appareil,
notamment des bougies allumées.
•Veillez à respecter les lois en vigueur lorsque
vous jetez les piles usagées.
•L’appareil ne doit pas être exposé à l’eau ou à
l’humidité.
•Ne pas poser d’objet contenant du liquide, par
exemple un vase, sur l’appareil.
•Ne pas manipuler le cordon d’alimentation avec
les mains mouillées.
•Lorsque l’interrupteur est sur la position OFF,
l’appareil n’est pas complètement déconnecté du
SECTEUR (MAINS).
•L’appareil sera installé près de la source
d’alimentation, de sorte que cette dernière soit
facilement accessible.
•Evite altas temperaturas.
Permite la suficiente dispersión del calor cuando
está instalado en la consola.
•Maneje el cordón de energía con cuidado.
Sostenga el enchufe cuando desconecte el
cordón de energía.
•Mantenga el equipo libre de humedad, agua y
polvo.
•Desconecte el cordón de energía cuando no
utilice el equipo por mucho tiempo.
•No obstruya los orificios de ventilación.
•No deje objetos extraños dentro del equipo.
•No permita el contacto de insecticidas, gasolina
y diluyentes con el equipo.
•Nunca desarme o modifique el equipo de
ninguna manera.
•La ventilación no debe quedar obstruida por
haberse cubierto las aperturas con objetos como
periódicos, manteles o cortinas.
•No deberán colocarse sobre el aparato fuentes
inflamables sin protección, como velas
encendidas.
•A la hora de deshacerse de las pilas, respete la
normativa para el cuidado del medio ambiente.
•No exponer el aparato al goteo o salpicaduras
cuando se utilice.
•No colocar sobre el aparato objetos llenos de
líquido, como jarros.
•No maneje el cable de alimentación con las
manos mojadas.
•Cuando el interruptor está en la posición OFF, el
equipo no está completamente desconectado de
la alimentación MAINS.
•El equipo se instalará cerca de la fuente de
alimentación de manera que resulte fácil acceder
a ella.
III
nCAUTIONS ON INSTALLATION
PRÉCAUTIONS D’INSTALLATION
EMPLAZAMIENTO DE LA INSTALACIÓN
z
z
z
z
Wall
Paroi
Pared
zFor
z
proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
•More than 0.3 m (12 in.) is recommended.
•Do not place any other equipment on this unit.
zPour
z
permettre la dissipation de chaleur requise, n’installez
pas cette unité dans un espace confiné tel qu’une bibliothèque
ou un endroit similaire.
•Une distance de plus de 0.3 m (12 po) est recommandée.
•Ne placez aucun matériel sur cet appareil.
zPara
z
la dispersión del calor adecuadamente, no instale este
equipo en un lugar confinado tal como una librería o unidad
similar.
•Se recomienda dejar más de 0.3 m (12 pulg.) alrededor.
•No coloque ningún otro equipo sobre la unidad.
ENGLISH
Simple version
Getting started
Thank you for purchasing this DENON product. To ensure proper operation, please read these owner’s manual carefully before using the product.
After reading them, be sure to keep them for future reference.
Contents
Simple version (Simple setup guide)···························3
Basic version· ·········································································12
Information· ············································································60
Check that the following parts are supplied with the product.
qOwner’s manual....................................................................... 1
wWarranty (for North America model only)................................. 1
eService network list.................................................................. 1
rRemote control unit (RC-1146)................................................. 1
tR6/AA batteries........................................................................ 2
ySetup microphone
(DM-A409, Cord length: Approx. 19.7 ft / 6.0 m)..................... 1
uAM loop antenna...................................................................... 1
iFM indoor antenna................................................................... 1
r
y
u
i
About this manual
nnOperation buttons
The operations described in this manual are based mainly on
remote control operation.
nnSymbols
v
This symbol indicates a reference page on which
related information is described.
This symbol indicates a supplementary information
and tips for operations.
NOTE
This symbol indicates points to remember operations
or function limitations.
nnIllustrations
Note that the illustrations in these instructions are for explanation
purposes and may differ from the actual unit.
1
Information
Part names and functions···························································61
Front panel···················································································61
Display·························································································61
Rear panel····················································································62
Remote control unit·····································································63
Other information········································································64
Trademark information·································································64
Surround······················································································65
Explanation of terms····································································69
Troubleshooting···········································································71
Resetting the microprocessor·····················································72
Specifications···············································································73
Accessories
Advanced version
Connections··················································································13
Important information··································································13
Connecting an HDMI-compatible device·····································14
Connecting a TV··········································································16
Connecting a Blu-ray Disc player / DVD player····························16
Connecting a set-top box (Satellite tuner/cable TV)·····················17
Connecting a digital camcorder···················································17
Connecting a control dock for iPod··············································18
Connecting an antenna································································18
Connecting an external control device·········································19
Playback (Basic operation)··························································19
Important information··································································19
Playing a Blu-ray Disc player/DVD player·····································20
Playing an iPod®· ········································································21
Tuning in radio stations································································23
Selecting a listening mode (Surround mode)···························24
Standard playback········································································24
DENON original surround playback··············································26
Stereo playback···········································································26
Direct playback············································································26
Advanced version ·······························································27
Speaker installation/connection (Other than 5.1-channel)······28
Install···························································································28
Connect·······················································································29
Set up speakers ··········································································31
Playback (Advanced operation)··················································32
Convenient functions···································································32
Playback in ZONE2 (Separate room) ·········································34
Audio output················································································34
Playback·······················································································35
Quick select function···································································35
How to make detailed settings···················································36
Menu map···················································································36
Examples of on-screen display and front display·························37
Inputting characters ····································································38
Input Setup··················································································39
Audio Adjust················································································43
Manual Setup··············································································48
Information··················································································55
Operating the connected devices by remote control unit·······56
Operating AV equipment·····························································56
Registering preset codes·····························································56
Operating components································································58
Specifying the zone used with the remote control unit···············59
Resetting the remote control unit················································59
Basic version
Getting started···············································································1
Accessories···················································································1
About this manual··········································································1
Features·························································································2
Cautions on handling·····································································2
ENGLISH
Features
Fully discrete, identical quality and power for all
7 channels (110 W x 7ch)
The unit is equipped with a power amplifier that plays back highfidelity sound in surround mode with equal quality and power for all
channels, true to the original sound.
The power amplifier circuit adopts a discrete-circuit configuration
that achieves high-quality surround sound play back.
Supports HDMI 1.4a with 3D, ARC, Deep Color,
x.v.Color , Auto Lipsync and HDMI control function
This unit can output 3D video signals input from a Blu-ray Disc
player to a TV that supports a 3D system. This unit also supports
the ARC (Audio Return Channel) function, which plays back TV
sound with this unit via an HDMI cable used for connecting the
unit and a TVz.
Cautions on handling
Auto setup function
The unit is provided with an “Auto setup function” which
automatically makes speaker settings best suited for the listening
environment. The sound from the speakers is picked up with the
supplied microphone. Reflecting sound and audio characteristics of
speakers are measured, and settings for an optimum sound field
are automatically made.
Upconverting of all types of source video signals
to HDMI signals
This unit is provided with functions for automatic conversion of
various video signals (component video, S-Video, video) that are
input to this unit into HDMI signals for output to a monitor, allowing
connection between this unit and a TV to be made with a single
HDMI cable.
The unit is equipped with 4 HDMI input connectors for connecting
devices with HDMI connectors, such as a Blu-ray Disc player,
game machine, HD video camera, etc.
High definition audio support
The unit is equipped with a decoder which supports high-quality
digital audio format for Blu-ray Disc players such as Dolby TrueHD,
DTS-HD Master Audio, etc.
Dolby Pro Logic gz
The unit is provided with a Dolby Pro Logic gz decoder. When
you play back the sound in Dolby Pro Logic gz playback with front
height speakers connected to the unit, you can enjoy playback
sound with rich spacial expression.
Easy to use, on-screen display
Simple settings are enabled with the setting menus displayed on
the TV screen. When you control the sound volume, the volume
level is displayed on the screen, and when you switch the input
source, the name of the input source is displayed.
2
•Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When going on vacation or leaving home
for long periods of time, be sure to unplug the power cord from the
power outlet.
•About Condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
Dock connecrivity for iPod and network streaming
•Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If that
occurs, move the mobile phone away from this unit when it is in use.
zAn
z Internet connection environment is required.
•Moving the unit
Turn off the power and unplug the power cord from the power
outlet. Next, disconnect the connection cables to other system units
before moving the unit.
zThe
z
TV should support the ARC function.
4-HDMI inputs and 1-output
•Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
If an optional DENON control dock for iPod (ASD-3N, ASD-3W,
ASD-51N or ASD-51W) is connected to this unit, you can listen to
Internet radio or enjoy music and photos stored in your PC.
•About Care
•Wipe the cabinet and control panel clean with a soft cloth.
•Follow the instructions when using a chemical cleaner.
•Benzene, paint thinner or other organic solvents as well as
insecticide may cause material changes and discoloration if brought
into contact with the unit, and should therefore not be used.
ENGLISH
Simple version
Simple version (Simple setup guide)
Simple
version
Here, we explain the entire setup procedure, from unboxing the unit to using it in a home theater.
The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.
See page 28 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.
nnBefore connecting the unit, turn off the power to all devices.
1
2
Install
(vpage 4)
3
Connect
(vpage 4)
4
Turn on
power
(vpage 6)
Basic version
nnFor operation of the connected devices, refer to the user manuals for each device.
5
Set up
speakers
Play back
disc
Use the setup microphone
(DM-A409) included with
the product, for automatic
setup.
Enjoy Blu-ray Disc and DVD
in surround sound.
(vpage 6)
(vpage 11)
Advanced version
Enjoy better audio, using
the correct install method.
Connect 5.1-channel
speakers, a TV and Bluray Disc player equipped
with an HDMI connector.
Information
Set up speakers (Audyssey® Auto Setup)
Preparation
Step 1
Speaker
Detection
Step 2
Measurement
Step 3
Calculating
Step 4
Check
Step 5
Store
Finish
3
ENGLISH
1 Install
1
2
3
4
5
This unit can perform 2.0/2.1 to 7.1-channel surround playback.
Here, we explain setup using the example of 5.1-channel speaker
playback.
FL
FR
SW
2 Connect
Speakers
Carefully check the left (L) and right (R)
channels and + (red) and – (black) polarities
on the speakers being connected to the
this unit, and be sure to interconnect the
channels and polarities correctly.
Connecting the speaker cables
Peel off about 0.03 ft/10 mm of sheathing from
the tip of the speaker cable, then either twist the
core wire tightly or terminate it.
C
22 – 30˚
120˚
SL
Front speaker (L)
Front speaker (R)
Center speaker
Subwoofer
Surround speaker (L)
Surround speaker (R)
•Install the surround speakers in a
position 2 to 3 ft (60 to 90 cm) higher
than ear level.
Front
speaker
Surround
speaker
3
4
5
NOTE
Speaker terminals
Speaker
impedance
FRONT
CENTER
SURROUND
SURR.BACK / AMP ASSIGN
6 – 16 Ω
When using a banana plug
Tighten the speaker terminal firmly before
inserting the banana plug.
2 – 3 ft /
60 – 90 cm
GViewed from the sideH
4
2
•Connect so that the speaker cable core wires
do not protrude from the speaker terminal.
The protection circuit may be activated if the
core wires touch the rear panel or if the + and –
sides touch each other (vpage 70 “Protection
Circuit”).
•Never touch the speaker terminals while the
power supply is connected. Doing so could
result in electric shock.
•Use speakers with the speaker impedances
shown below.
SR
Listening position
FL
FR
C
SW
SL
SR
1
The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.
See page 28 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.
ENGLISH
Blu-ray Disc player and TV
TV
Basic version
Use only an HDMI (High Definition Multimedia Interface) cable that bears the HDMI
logo (a certified HDMI product). Using a cable without the HDMI logo (an uncertified
HDMI product) may result in abnormal playback.
When outputting Deep Color or 1080p, etc., we recommend you use a “High Speed
HDMI cable” or a “High Speed HDMI cable with Ethernet” for enhanced high-quality
playback.
Simple version
Connect
Blu-ray Disc player
Audio cable
(sold separately)
HDMI
IN
HDMI cable
(sold separately)
FL
Advanced version
HDMI
OUT
HDMI cable
(sold separately)
FR
SW
C
Subwoofer
with built-in
amplifier
Information
SL
Speaker cables
(sold separately)
SR
To household power outlet
(AC 120 V, 60 Hz)
Power cord
NOTE
•Do not plug in the power cord until all connections have been completed.
•Do not bundle power cords together with connection cables. Doing so can result in humming or noise.
5
ENGLISH
3 Turn on power
1
Turn on the TV and subwoofer
power.
Power on
the TV input to the input of
2 Change
this unit.
POWER ON to turn on power
3 Press
to the unit.
The power indicator flashes green and the
power turns on.
Power on
1
2
3
4
5
4 Set up speakers
(Audyssey® Auto Setup)
2
3
4
5
The acoustic characteristics of the connected speakers and listening room are
measured and the optimum settings are made automatically. This is called
“Audyssey Auto Setup”.
To perform measurement, place the setup microphone in multiple locations all
around the listening area. For best results, we recommend you measure in six
positions, as shown in the illustration (up to six positions).
•• When performing Audyssey Auto Setup, MultEQ®/Dynamic EQ®/Dynamic
Volume® functions become active (vpage 46, 47).
•• To set up the speakers manually, use “Speaker Setup” (vpage 49) on the menu.
NOTE
•Make the room as quiet as possible. Background noise can disrupt the room measurements. Close
windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances,
light dimmers, or other devices as measurements may be affected by these sounds.
•Cell phones should be placed away from all audio electronics during the measurement process as Radio
Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).
•Do not unplug the setup microphone from the main unit until Audyssey Auto Setup is completed.
•Do not stand between the speakers and setup microphone or allow obstacles in the path while the
measurements are being made. This will cause inaccurate readings.
•Loud test sounds may be played during Audyssey Auto setup. This is part of
normal operation. If there is background noise in room, these test signals will
increase in volume.
•Operating VOL df during the measurements will cancel the measurements.
•Measurement cannot be performed when headphones are connected.
Power on
6
1
The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.
See page 28 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.
ENGLISH
Set up speakers (Audyssey® Auto Setup)
GExample qH
GExample wH
FL SW C
FL SW C
FR
( : Measuring positions)
Mount the setup microphone on a tripod or stand
and place it in the main listening position.
When placing the setup microphone, adjust the height of the
sound receptor to the level of the listener’s ear.
Sound receptor
3
Set up the remote control unit
nn Set up the zone mode
Press ZONE SELECT to switch the zone mode to
“MAIN”.
The “MAIN” indicator lights.
Setup
microphone
Basic version
•Measurements are performed by placing the setup microphone
successively at multiple positions throughout the entire listening
area, as shown in GExample qH. For best results, we recommend
you measure in six positions, as shown in the illustration (up to six
positions).
•Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment
results in more effective correction.
Set up the microphone
Simple version
1
About setup microphone placement
FR
( : Measuring positions)
Press ZONE SELECT
*M
FL Front speaker (L)
FR Front speaker (R)
C Center speaker
SR
SL
*M
SR
SW Subwoofer
SL Surround speaker (L)
SR Surround speaker (R)
About the main listening position (*M)
The main listening position is the position where listeners would
normally sit or where one would normally sit alone within the listening
environment. Before starting Audyssey Auto Setup, place the setup
microphone in the main listening position. Audyssey MultEQ® uses
the measurements from this position to calculate speaker distance,
level, polarity, and the optimum crossover value for the subwoofer.
NOTE
•Do not hold the setup microphone in your hand during
measurements.
•Avoid placing the setup microphone close to a seat back or wall as
sound reflections may give inaccurate results.
2
Advanced version
SL
nn Set up the operation mode
Press AMP to set the remote control unit to amplifier
operation mode.
Set up the subwoofer
If using a subwoofer capable of the following
adjustments, set up the subwoofer as shown below.
Press AMP
nn When using a subwoofer with a direct mode
Set the direct mode to “On” and disable the volume adjustment
and crossover frequency setting.
nn When using a subwoofer without a direct mode
The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.
See page 28 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.
Information
Make the following settings:
•Volume : “12 o’clock position”
•Crossover frequency :
“Maximum/Highest Frequency”
•Low pass filter : “Off”
•Standby mode : “Off”
7
ENGLISH
Set up speakers (Audyssey® Auto Setup)
Preparation
4
Connect the setup microphone to the
SETUP MIC jack of this unit.
Step 1
Speaker Detection
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Amp Assign:
ZONE2
Start
Cancel
[ENT]:Select [RTN]:Back
Here, we explain setup using the example of
5.1-channel speaker playback.
For settings other than 5.1-channel surround,
select “Amp Assign” and perform steps 3 to 4 of
“Set up speakers” (vpage 31).
5
Measurement
•In step 1, you will perform measurements at the main listening position.
•This step automatically checks the speaker configuration and speaker size, and calculates the channel
level, distance, and crossover frequency. It also corrects distortion in the listening area.
6 The detected speakers are displayed.
When the setup microphone is
connected, the following screen is
displayed.
Step 2
NOTE
Step1:Speaker Detection
MultEQ
Front Sp.
:Yes
Center Sp.
:Yes
Subwoofer
:Yes
Surround Sp.
:Yes
If “Caution” is displayed:
Go to “Error messages” (vpage 10), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.
Next
Retry
[ENT]:Next
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press
ENTER.
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
Use ui to select “Next” and then
7 press
ENTER.
When measuring has stopped
q Press ui to select “Cancel”, then press
ENTER.
w Press o p to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of Preparation
.
•In step 2, you will perform measurements at
multiple positions (two to six positions) other than
the main listening position.
•You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
the setup microphone to
8 Move
position 2, use ui to select “Next”,
and then press ENTER.
The measurement of the second position
starts. Measurements can be made in up to
six positions.
Step2:Measurement
MultEQ
Please place microphone
at ear height at
2nd listening position.
Next
Calculate
Cancel
[ENT]:Next
If you want to omit measurements from the next
position onward, select “Calculate”.
(Go to Step 3 Calculating
)
step 8, measuring positions 3
9 Repeat
to 6.
Use ui to select “Start” and then
press ENTER.
When measurement of position 6 is
completed, a “All the measurements were
finished.” message is displayed.
When measuring begins, a test tone is
output from each speaker.
•Measurement requires several minutes.
Step2:Measurement
MultEQ
All the measurements
were finished.
If “Cancel” is selected
“Cancel Auto Setup?” is displayed on the TV
screen. If “Yes” is selected, “Audyssey Auto
Setup” closes.
Calculate
Retry
Cancel
[ENT]:Calculate
8
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
ENGLISH
Set up speakers (Audyssey® Auto Setup)
Calculating
Step 4
Step 5
Check
Simple version
Step 3
Finish
Store
Unplug the setup microphone from
Use ui to select the item you want
Use ui to select “Store” and then
the
screen, use ui
10 On
11
13
14
the unit’s SETUP MIC jack.
to
check,
and
then
press
ENTER
.
press
ENTER
.
to select “Calculate”, and then press
®
ENTER.
15 Set Dynamic Volume .
Step 2
MultEQ
Please check the results
of the measured item.
Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.
MultEQ
Calculating
Please wait...
•Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.
•If you want to check another item, press
RETURN.
12
Store
Cancel
MultEQ
Storing complete.
Auto Setup is now
finished.
Turn on Dynamic Volume?
Yes : No
[
Step5:Store
Storing
Please wait...
NOTE
MultEQ
[----------]
•Saving the results requires about 10 seconds.
•If you do not want to save the measurement
results, use ui to select “Cancel”, then select
“Yes” using o p. All the measured Audyssey
Auto Setup data will be erased.
]:Select
[ENT]:Exit
•For details of Dynamic Volume settings, see
page 47.
nn When turning Dynamic Volume on
•Use o to select “Yes”, and then press ENTER.
The unit automatically enters “Evening” mode.
nn When turning Dynamic Volume off
•Use p to select “No”, and then press ENTER.
NOTE
After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
NOTE
During saving of measurement results, be sure
not to turn off the power.
Information
Move the cursor
(Up/Down/Left/Right)
Finish
[ENT]:Store
Use ui to select “Next” and then
press ENTER.
•If the result differs from the actual connection
status, or if “Caution!” is displayed, see “Error
messages” (vpage 10). Then carry out Audyssey
Auto Setup again.
•If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.
•If you change speaker positions or orientation,
perform Audyssey Auto Setup again to find the
optimal equalizer settings.
Remote control operation
buttons
MultEQ
Please select “Store”
to store measurement
values.
Advanced version
•Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.
Step5:Store
Speaker Config.Check
Distance Check
Channel Level Check
Crossover Freq.Check
Next
[ENT]:Select
Step3:Calculating
[----------]
Save the measurement results.
Basic version
Step4:Check
Confirm the setting
Return to previous menu
9
ENGLISH
Error messages
Parameter Check
An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
This function enables you to check the measurement results and
equalizer characteristics after Audyssey Auto Setup.
NOTE
Be sure to turn off the power before checking speaker connections.
Examples
Caution
Error details
MultEQ
FMicrophone:None
or
Speaker
:None
Measures
•The connected setup microphone is broken, or a •Connect the included setup microphone to the
device other than the supplied setup microphone SETUP MIC jack of this unit.
is connected.
•Not all speakers could be detected.
•The front L speaker was not properly detected. •Check the speaker connections.
Use ui to select “Parameter Check” and then
1 press
ENTER.
Use ui to select the item you want to check, then
2 press
ENTER.
3-2.Parameter Check
Speaker Config.Check
Distance Chenck
Channel Level Check
Crossover Freq.Check
EQ Check
Retry
Cancel
[ENT]:Retry
Restore
Caution
MultEQ
FAmbient noise is
too high or
Level is too low.
Retry
Cancel
•There is too much noise in the room for accurate •Either turn off any device generating noise or
measurements to be made.
move it away.
•Perform again when the surroundings are quieter.
•Speaker or subwoofer sound is too low for •Check the speaker installation and the direction
accurate measurements to be made.
in which the speakers are facing.
•Adjust the subwoofer’s volume.
[ENT]:Retry
•The displayed speaker could not be detected.
Caution
•Check the connections of the displayed speaker.
Retry
Cancel
Skip
]:Up/Down [
Check the distance.
Channel Level Check
Check the channel level.
Crossover Freq. Check
Check the crossover frequency.
EQ Check
Check the equalizer.
MultEQ
Retry
Cancel
Skip
]:Up/Down [
3 Press RETURN.
]:CH
Front
L :Phase
10
Distance Check
Check the speaker configuration.
•If “EQ Check” is selected in step 2, press ui to select equalizing
curve (“Audyssey” or “Audyssey Flat”) to be checked.
Use o p to switch the display between the different speakers.
Caution
[
Speaker Config. Check
MultEQ
Front
R :None
[
[ENT]:Select [RTN]:Back
The confirmation screen reappears. Repeat steps 2 and 3.
•The displayed is connected with the polarities •Check the polarities of the displayed speaker.
reversed.
•For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure the connection is
correct, press ui to select “Skip”, then press
ENTER.
Retrieving Audyssey Auto Setup settings
If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup
measurement result (value calculated at the start by MultEQ®) even
when you have changed each setting manually.
]:CH
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
ENGLISH
Make the necessary settings on the
player (language setting, subtitles
setting, etc.) beforehand.
3
Adjust the sound volume.
2
3
4
5
When power is switched to standby
Press POWER OFF.
GPower indicator status in standby modeH
•Normal standby : Off
•When “HDMI Control” is set to “ON” : Red
Basic version
1
the component connected to
2 Play
this unit.
Press BD to switch an input source
for a player used for playback.
1
Simple version
5 Play back disc
You can also switch the power to standby by
pressing ON/STANDBY on the main unit.
VOL d············································ Volume up
VOL f······································· Volume down
MUTE··················································· Muting
NOTE
Set the listening mode according to the playback contents
(cinema, music, etc.) or according to your liking (vpage 24
“Selecting a listening mode (Surround mode)”).
Advanced version
4 Set the listening mode.
During power standby, a minimal amount of power is consumed. To
totally cut off the power, remove the power cord from the power
outlet.
Information
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
11
ENGLISH
Basic
version
Basic version
Here, we explain the connections and basic operation methods for this unit.
F Connections vpage 13
F Playback (Basic operation) vpage 19
F Selecting a listening mode (Surround mode) vpage 24
nnRefer to the pages indicated below for information on connecting and playing back the various
media and external devices.
Audio and video
Playback
TV
vpage 14, 16
–
Blu-ray Disc player
vpage 14, 16
vpage 20
DVD player
vpage 14, 16
vpage 20
Set-top box (Satellite tuner or cable TV)
vpage 14, 17
–
Game console
vpage 14
–
Digital camcorder
vpage 17
–
Control dock for iPod
vpage 18
vpage 21
Audio
Radio
For speaker connections, see page 4.
12
Connection
Connection
vpage 18
Playback
vpage 23
ENGLISH
Simple version
Connections
Important information
•Make connections as follows before using this unit. Select an appropriate connection type
according to the components to be connected.
•You may need to make some settings on this unit depending on the connection method. Refer to
each description for more information.
•Select the cables (sold separately) according to the components being connected.
NOTE
Converting input video signals for output (Video conversion function)
This unit is equipped with four types of video input connectors (HDMI, Component video, S-Video and
video) and two types of video output connectors (HDMI and video).
Use the connectors corresponding to the components to be connected.
This function automatically converts various formats of video signals input to this unit into the formats used
to output the video signals from this unit to a monitor.
This unit
Monitor
Output
(MONITOR OUT)
HDMI connector
HDMI connector
HDMI
connector
Component video
connectors
Component video
connectors
S-Video connector
S-Video connector
Video connector
Video connector
Video connector
Input
HDMI connector
Information
Input
(IN)
•HDMI signals cannot be converted into analog signals.
•When a non-standard video signal from a game machine or some other source is input, the video
conversion function might not operate.
•Component video input signals cannot be converted into Video format.
Advanced version
Output
•The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60
formats.
•Resolutions of HDMI-compatible TVs can be checked at “HDMI Monitor Information” (vpage 55).
NOTE
GFlow of video signals for MAIN ZONEH
Video device
Basic version
•Do not plug in the power cord until all connections have been completed.
•When making connections, also refer to the operating instructions of the other components being
connected.
•Be sure to connect the left and right channels properly (left with left, right with right).
•Do not bundle power cords together with connection cables. Doing so can result in noise.
Video connector
13
ENGLISH
Important information
How the on-screen display appears in accordance with the video
input signal
The way the on-screen display of the menus, status, etc., is displayed differs according to the type of video
signal input to this unit.
nnWhen video signals are input from the HDMI or component video connector
•Menu: Switches to a screen with a black background and the menu is superimposedz.
•Status display: Not displayed.
zIf
z you want to display the menus superimposed on the background image, input the same video signals
to the video connectors. When a menu is displayed, the picture switches to the one being input from
the video connectors and the menu is displayed superimposed over this picture.
Connecting an HDMI-compatible device
You can connect up to five HDMI-compatible devices to the unit.
HDMI function
This unit supports the following HDMI functions:
•3D
•Deep Color (vpage 69)
•Auto Lip Sync (vpage 51)
•x.v.Color, sYCC601 color, Adobe RGB color, Adobe YCC601color (vpage 69, 70)
•High definition digital audio format
•ARC (Audio Return Channel)
•Content Type
•CEC (HDMI control)
nnWhen video signals are input from the S-Video or video connector
•Menu: Menus are displayed superimposed over the background image.
•Status display: Displayed.
Examples of on-screen display
•Menu screen
•Status display screen
When the input source is
switched
•When the volume is adjusted
Copyright protection system
In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection, both
this unit and TV or the player need to support the copyright protection system known as HDCP (Highbandwidth Digital Content Protection System). HDCP is copyright protection technology comprised of
data encryption and authentication of the connected AV device. This unit supports HDCP.
•If a device that does not support HDCP is connected, video and audio are not output correctly. Read
the owner’s manual of your television or player for more information.
MENU
About HDMI cables
1.Audio Adjust
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
•When a device supporting Deep Color signal transfer is connected, use a cable compatible “High Speed
HDMI cable” or “High Speed HDMI cable with Ethernet”
•When the ARC function is used, connect a device with a ”Standard HDMI cable with Ethernet” or “High
Speed HDMI cable with Ethernet” for HDMI 1.4a.
[ENT]:Select
[Auto]
IN :DVD
MODE:STEREO
Master Volume -80.0dB
Status display: The operating status appears briefly on the screen
when the input source is switched or the volume is
changed.
HDMI control function (vpage 32)
This function allows you to operate external devices from the receiver and operate the receiver from
external devices.
NOTE
•The HDMI control function may not work depending on the device it is connected to and its settings.
•You cannot operate a TV or Blu-ray Disc player / DVD player that is not compatible with the HDMI control
function.
About 3D function
This unit supports input and output of 3D (3 dimensional) video signals of the HDMI 1.4a standards, For
playing the 3D video content, a player, and a TV that support the 3D function of the HDMI 1.4a standards
are required in addition to this unit.
14
ENGLISH
Connecting an HDMI-compatible device
NOTE
•To enable the ARC function,set “HDMI Control” to “ON” (vpage 51).
•When connecting a TV that does not support the ARC function, a separate audio cable is required. In this
case, refer to “Connecting a TV” (vpage 16) for the connection method.
NOTE
To enable the Content type, set “Video Mode” to “Auto” (vpage 42).
NOTE
The audio signal from the HDMI output connector (sampling frequency, number of channels, etc.) may be
limited by the HDMI audio specifications of the connected device regarding permissible inputs.
Basic version
About Content Type
The HDMI Specification Version 1.4a enables simple, automated picture setting selection with no user
intervention.
•When this unit is connected to other devices with HDMI cables, connect this unit and TV also with an
HDMI cable.
•When connecting a device that supports Deep Color transmission, please use a “High Speed HDMI
cable” or “High Speed HDMI cable with Ethernet”.
•Video signals are not output if the input video signals do not match the monitor’s resolution. In this case,
switch the Blu-ray Disc/DVD player’s resolution to a resolution with which the monitor is compatible.
•When this unit and monitor are connected with an HDMI cable, if the monitor is not compatible with
HDMI audio signal playback, only the video signals are output to the monitor.
Simple version
About ARC (Audio return channel) function
The Audio Return Channel in HDMI 1.4a enables a TV, via a single HDMI cable, to send audio data
“upstream” to this unit.
Connecting to a device equipped with a DVI-D connector
Cables used for connections
When an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to
DVI signals, allowing connection to a device equipped with a DVI-D connector.
Audio and video cable (sold separately)
NOTE
HDMI cable
Blu-ray Disc
player
DVD player
Set-top box
Game
console
TV
HDMI
OUT
HDMI
OUT
HDMI
OUT
HDMI
OUT
HDMI
IN
nnSettings related to HDMI connections
Set as necessary. For details, see the respective reference pages.
Advanced version
•This interface allows transfer of digital video signals and digital audio signals over a single HDMI cable.
•No sound is output when connected to a device equipped with a DVI-D connector. Make separate audio
connections.
•Signals cannot be output to DVI-D devices that do not support HDCP.
•Depending on the combination of devices, the video signals may not be output.
Input Assign (vpage 41)
Set this to change the HDMI input connector to which the input source is assigned.
HDMI Setup (vpage 51)
Make settings for HDMI video/audio output.
•Auto Lip Sync
•HDMI Audio Out
•HDMI Control
•Standby Source
•Power Off Control
Information
NOTE
The audio signals output from the HDMI connectors are only the HDMI input signals.
15
ENGLISH
Connecting a TV
•Select the connector to use and connect the device.
•For video connections, see “Converting input video signals for output (Video conversion function)”
(vpage 13).
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage 14).
To listen to TV audio through this device, use the optical digital connection.
NOTE
This connection is not required when a TV compatible with the ARC function (Audio Return Channel (HDMI
1.4a standard function)) is connected to this unit via an HDMI connection.
For details, see “About ARC (Audio return channel) function” (vpage 15) or refer to the instruction manual
for your TV.
Cables used for connections
Video cable (sold separately)
Video cable
(Yellow)
Audio cable (sold separately)
Connecting a Blu-ray Disc player / DVD player
•You can enjoy video and audio from a Blu-ray Disc or DVD.
•Select the connector to use and connect the device.
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage 14).
Cables used for connections
Video cable (sold separately)
Video cable
(Yellow)
Audio cable (sold separately)
Audio cable
(White)
L
L
(Red)
R
R
Blu-ray Disc player
/ DVD player
VIDEO
AUDIO
VIDEO
OUT
AUDIO
OUT
L
R
Optical cable
L
R
L
R
TV
VIDEO
AUDIO
VIDEO
IN
OPTICAL
OUT
in Set as Necessary
Set this to change the digital input connector to which the input source is assigned.
“Input Assign” (vpage 41)
in Set as Necessary
Set this to change the digital input connector to which the input source is assigned.
“Input Assign” (vpage 41)
16
For HD audio (Dolby TrueHD, DTS-HD, Dolby Digital Plus and DTS Express) playback, connect with HDMI
(vpage 14 “Connecting an HDMI-compatible device”).
ENGLISH
Cables used for connections
Video cable
(Yellow)
Audio cable (sold separately)
(Green)
Audio cable
(Blue)
Coaxial
digital cable
(White)
L
L
(Red)
R
R
(Red)
Digital camcorder
Audio cables (sold separately)
Audio cable
(Yellow)
Basic version
Component
video cable
Cables used for connections
Video cable (sold separately)
Video cable (sold separately)
Video cable
Connecting a digital camcorder
•You can enjoy video and audio from a digital camcorder.
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage 14).
Simple version
Connecting a set-top box (Satellite tuner/cable TV)
•You can watch satellite or cable TV.
•Select the connector to use and connect the device.
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage 14).
(White)
L
L
(Red)
R
R
VIDEO
AUDIO
VIDEO
OUT
AUDIO
OUT
L
R
(Orange)
L
R
L
R
Satellite Tuner/Cable TV
Advanced version
AUDIO
VIDEO
COMPONENT VIDEO
OUT
Y
PB PR
VIDEO
OUT
COAXIAL
OUT
AUDIO
OUT
L
R
L
R
L
R
in Set as Necessary
Set this to change the digital input connector to which the input source is assigned.
“Input Assign” (vpage 41)
You can enjoy games by connecting a game machine via the V.AUX input connector. In this case, set the
input source to “V.AUX”.
in Set as Necessary
Set this to change the digital input connector or component video input connector to which the input
source is assigned.
“Input Assign” (vpage 41)
When a non-standard video signal from a game machine or some other source is input, the video conversion
function might not operate. In this case, use the monitor output of the same connector as the input.
17
Information
NOTE
ENGLISH
Connecting a control dock for iPod
•Connect a control dock for iPod to the unit to enjoy video and music
stored on an iPod.
•For a control dock for iPod, use ASD-1R, ASD-11R, ASD-3N, ASD3W, ASD-51N and ASD-51W made by DENON (sold separately).
•For instructions on the control dock for iPod settings, refer to the
control dock for iPod’s operating instructions.
Control dock for iPod
Connecting an antenna
•Connect the FM antenna or AM loop antenna supplied with the unit
to enjoy listening to radio broadcasts.
•After connecting the antenna and receiving a broadcast signal
(vpage 23 “Listening to FM/AM broadcasts”), fix the antenna with
tape in a position where the noise level becomes minimal.
AM loop antenna
(supplied)
Direction of broadcasting station
FM outdoor
antenna
nnAM loop antenna assembly
the stand section
1 Put
through the bottom of the
loop antenna from the
rear and bend it forward.
the projecting part
2 Insert
into the square hole in
Stand
Square
hole
Loop
antenna
Projecting
part
the stand.
ASD-51N
75 Ω coaxial
cable
R
FM indoor
antenna
(supplied)
e
NOTE
L
Black
zUse
z
the AV/Control Cable supplied with the DENON
control dock for iPod.
in Set as Necessary
Set this to change the digital input connector to which the input
source is assigned.
“Input Assign” (vpage 41)
18
w
L
z
R
q
Ground
White
AM outdoor
antenna
•Do not connect two FM antennas simultaneously.
•Even if an external AM antenna is used, do not disconnect the AM
loop antenna.
•Make sure the AM loop antenna lead terminals do not touch metal
parts of the panel.
•If the signal has noise interference, connect the ground terminal
(GND) to reduce noise.
•If you are unable to receive a good broadcast signal, we recommend
installing an outdoor antenna. For details, inquire at the retail store
where you purchased the unit.
nnUsing the AM loop antenna
Suspending on a wall
Suspend directly on a wall without assembling.
Nail, tack, etc.
Standing alone
Use the procedure shown left to assemble.
ENGLISH
REMOTE CONTROL jacks
If this unit is installed in a location that is out of range of the signal
from the remote control unit, you can still operate the unit and the
devices connected to it by using a commercially available IR receiver.
You can also use it to remotely control ZONE2 (another room).
AUX
OUT
Input
Infrared
sensor
Output
Device equipped with a
REMOTE CONTROL IN jack
nn Selecting the input source (vpage 19)
nn Adjusting the master volume (vpage 20)
nn Turning off the sound temporarily (vpage 20)
nn Playing a Blu-ray Disc player/DVD player
(vpage 20)
nn Playing an iPod® (vpage 21)
nn Tuning in radio stations (vpage 23)
Selecting a listening mode (Surround mode)
(vpage 24)
Playback (Advanced operation) (vpage 32)
Important information
Before starting playback, make the connections between the different
components and the settings on the receiver.
NOTE
Also refer to the operating instructions of the connected components
when playing them.
Selecting the input source
Press the input source select button
(iPod, DVD, BD, TUNER, DOCK, SAT/
CBL, GAME, V.AUX, TV) to be played
back.
You can also use the following operation to select an input
source.
Advanced version
The desired input source can be selected
directly.
•When iPod PLAY is pressed, the input
source of this unit is switched to “DOCK”
and the connected iPod is automatically
played (vpage 22 “iPod play function”).
Basic version
Infrared
retransmitter
Playback (Basic operation)
Simple version
Connecting an external control
device
Information
19
ENGLISH
Important information
nnUsing the “Source Select” menu
Adjusting the master volume
Use VOL df to adjust the volume.
qPress SOURCE SELECT.
Display the “Source Select” menu.
Source Select
TUNER
BD
DVD
TV
SAT/CBL
GAME
V.AUX
DOCK
The currently selected input source
[
]:Source is highlighted.
[ENT]:Select
wUse uio p to select the input source,
then press ENTER.
The input source is set and the source
selection menu is turned off.
•Input sources that are not going to be used can be set ahead of time.
Make this setting at “Source Delete” (vpage 53).
•To turn off the source selection menu without selecting an input
source, press SOURCE SELECT again.
nnUsing the knob on the main unit
TUNER
20
DVD
DOCK
TV
SAT/CBL
V.AUX
GAdjustable rangeH
–––
–80.5dB – 18.0dB
nn When the “Volume Display” setting (vpage 53) is
“Absolute”
GAdjustable rangeH 0.0 – 99.0
•The variable range differs according to the input signal and channel
level setting.
You can also operate via the main unit.
In this case, perform the following
operations.
Turn MASTER VOLUME to adjust the
volume.
Turning off the sound temporarily
Press MUTE.
Turn SOURCE SELECT.
•Turning SOURCE SELECT switches
the input source, as shown below.
BD
nn When the “Volume Display” setting
(vpage 53) is “Relative”
GAME
•The sound is reduced to the level set at “Mute Level” (vpage 53).
•To cancel, press MUTE again. Muting can also be canceled by
adjusting the master volume.
Playing a Blu-ray Disc player/DVD
player
The following describes the procedure for playing Blu-ray Disc player/
DVD player.
1 Prepare for playback.
qTurn on the power of the TV,
subwoofer and player.
wChange the TV input to the input of
this unit.
eLoad the disc in the player.
Press POWER ON to turn on
2 power
to the unit.
BD or DVD to switch an
3 Press
input source for a player used for
playback.
4 Play the component connected to this unit.
Make the necessary settings on the player (language setting,
subtitles setting, etc.) beforehand.
ENGLISH
You can play back both video, photo and audio.
Listening to music on an iPod®
Press SEARCH and hold it down for 2 seconds or
4 more
to select the display mode.
DENON Control dock for iPod usable on this unit
•ASD-1R/ASD-11R/ASD-3N/ASD-3W/ASD-51N/ASD-51W
•There are two modes for displaying the contents recorded on the
iPod.
1
Prepare for playback.
qConnect the DENON control dock for iPod to this unit
2 Press POWER ON to turn on power to the unit.
3 Press DOCK to switch the input source to “DOCK”.
•If “Browse mode” is selected in step 4, the following screen is
displayed on a TV screen, depending on the connected control
dock for iPod.
GWhen using an ASD-1RH
GWhen using an ASD-11RH
Music
iPod
[
1/6
]
[
1/2
]
iPod
Music
Video
Browse mode
Music file
Playable
Photo file
files
Video file
Active
buttons
Remote
control unit
(This unit)
P
Playback starts.
P z2
P
P
P
•In Browse mode, press STATUS during
playback to check the title name, artist
name, and album name.
NOTE
•Press POWER OFF and set this unit’s power
to the standby mode before disconnecting
the iPod. Also switch the input source to
“DOCK” before disconnecting the iPod.
•Depending on the type of iPod and the software version, some
functions may not operate.
•Note that DENON will accept no responsibility whatsoever for any
problems arising with the data on an iPod when using this unit in
conjunction with the iPod.
Viewing videos on an iPod® in the Browse
mode
When an iPod equipped with a video function is connected to a
DENON ASD-11R, ASD-3N, ASD-3W, ASD-51N and ASD-51W control
dock for iPod, image files can be played in the Browse mode.
Use ui to select “Videos”, then
1 press
ENTER or p.
ui to select the search item
2 orUsefolder,
then press ENTER or p.
ui to select the video file, then press ENTER,
3 Use
p or 1.
Playback starts.
OK to disconnect.
21
Information
NOTE
P
Pz1
Use ui to select the item, then
press ENTER or p to select the
file to be played.
6 Press ENTER, p or 1.
•In “Browse mode”, the iPod display is as
shown at right.
Remote mode
P z2
z1 When using an ASD-11R, ASD-3N, ASD3W, ASD-51N or ASD-51W DENON
control dock for iPod.
z2 Video may not be output, depending on
the combination of ASD-1R, ASD-11R,
ASD-3N, ASD-3W, ASD-51N or ASD51W DENON control dock for iPod and
iPod.
5
Select
If the connections screen is not displayed,
the iPod may not be properly connected.
Reconnect it.
Display mode
iPod®
GWhen using an ASD-3N, ASD-3W, ASD-51N and ASD-51WH
Up/Down
Display iPod information on the iPod screen.
•“Remote iPod” or “Dock Remote” is displayed on the display
of this unit.
Track
Select
Advanced version
Music
Videos
Playlists
Artists
Albums
Songs
Genres
Composers
Remote mode
Basic version
(vpage 18 “Connecting a control dock for iPod”).
wSet the iPod® in the DENON control dock for iPod.
Browse mode
Display iPod information on the TV screen.
•English letters, numbers and certain symbols are displayed.
Incompatible characters are displayed as “.” (period).
•You can specify the duration of the on-screen display to be displayed
(default: 30 sec) at menu “iPod” (vpage 54). Press uio p to
return to the original screen.
•To play back compressed audio with extended bass or treble
reproduction, we recommend playback in RESTORER mode
(vpage 48). The default setting is “Mode 3”.
Simple version
Playing an iPod®
ENGLISH
Playing an iPod®
Viewing photos and videos on an iPod® in
the Remote mode
This unit can play back on a TV screen photos and data stored on an
iPod equipped with a slide show or video function.
1
Press and hold SEARCH to set the
Remote mode.
“Remote iPod” or “Dock Remote” is
displayed on the display of this unit.
Watching the iPod’s screen, use ui to select
2 “Photos”
or “Videos”.
•Depending on the iPod model, it may be necessary to operate the
iPod unit directly.
3
Press ENTER until the image you want to view is
displayed.
“TV Out” at the iPod’s “Slide show Settings” or “Video Settings”
must be set to “On” in order to display the iPod’s photo data or videos
on the monitor. For details, see the iPod’s operating instructions.
NOTE
Video may not be output, depending on the combination of ASD-1R,
ASD-11R, ASD-3N, ASD-3W, ASD-51N or ASD-51W and iPod.
22
iPod operation
iPod play function
Operation buttons
MENU
uio p
ENTER
Function
Amp menu
Cursor operation
Enter setting
SEARCH
(Press and release)
Page search modez1
SEARCH
(Press and hold)
Browse / Remote mode switching
RETURN
Return
6 7
(Press and hold)
Manual search
(fast-reverse/fast-forward)
1
8 9
3
2
RESTORER
MEMORY
TV POWER
TV INPUT
Playback / Pause
Auto search (cue)
Pause
Stop
RESTORER
Store memoryz2
TV power on/standby (Default : SONY)
Switch TV input (Default : SONY)
•Repeat playback (vpage 43 “Repeat”)
•Shuffling playback (vpage 43 “Shuffle”)
z1
z This functions when an ASD-1R or ASD-11R is
used.
z2
z This functions when an ASD-3N, ASD-3W, ASD51N or ASD-51W is used.
If iPod PLAY is pressed when power of this unit is on standby and a
control dock for iPod is connected, the iPod starts playback.
Press iPod PLAY.
•Power of this unit is turned on.
•This unit’s input source switches to
“DOCK”.
•iPod playback starts.
If iPod PLAY on the main unit is
pressed, the same function as with the
remote control unit can be obtained.
NOTE
iPod play function does not function if a control dock for iPod (“DOCK”)
is not connected.
ENGLISH
Listening to FM/AM broadcasts
TUNER to switch the input
1 Press
source to “TUNER”.
BAND to select “FM” or
2 Press
“AM”.
When listening to an FM broadcast.
AM
When listening to an AM broadcast.
in the desired broadcast
3 Tune
station.
qTo tune in automatically
nnTuner (FM/AM) operation
Operation buttons
CH +, –
MENU
uio p
ENTER
SEARCH
RETURN
BAND
MODE
TUNING df
0–9
•If the desired station cannot be tuned in with auto tuning, tune it in
manually.
•When tuning in stations manually, press and hold TUNING d or
TUNING f to change frequencies continuously.
•You can specify the duration of the on-screen display to be displayed
(default: 30 sec) at menu “TUNER” (vpage 54). Press uio p to
return to the original screen.
in the broadcast station you
1 Tune
want to preset.
2 Press MEMORY.
SHIFT to select the block
3 Press
(A to G) in which to preset the
channel (1 to 8 per block), then
press CH +, CH – or 1 – 8 to select
the preset number.
MEMORY again to complete
4 Press
the setting.
•To preset other stations, repeat steps 1 to
4.
Default settings
Block (A – G)
and
Channel (1 – 8)
A1 – A8
B1 – B8
C1 – C8
D1 – D8
E1 – E8
F1 – F8
G1 – G8
Default Settings
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 /
90.1 MHz
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
Press SHIFT to select the memory
1 block
(A to G).
Press CH +, CH – or 1 – 8 to select
2 the
desired preset channel.
You can also operate via the main unit.
In this case, perform the following
operations.
Press TUNING PRESET, then turn SOURCE
SELECT to select the preset radio station.
nnDirect frequency tuning
You can enter the receiving frequency directly to tune in.
1 Press SEARCH.
2 Input frequencies using the 0 – 9.
•If o is pressed, the immediately preceding
input is cancelled.
setting is completed, press
3 When
ENTER.
The preset frequency is tuned in.
Information
SHIFT
MEMORY
TV POWER
TV INPUT
Function
Preset channel selection
Amp menu
Cursor operation
Enter setting
Direct frequency tuning
Return
FM/AM switching
Switch search modes
Tuning (up/down)
Preset channel selection (1 – 8) /
Direct frequency tuning (0 – 9)
Preset channel block selection
Preset memory registration
TV power on/standby (Default : SONY)
Switch TV input (Default : SONY)
•Stations can be preset automatically at “Auto Preset”
(vpage 40). If “Auto Preset” is performed after performing “Manual
Preset”, the “Manual Preset” settings will be overwritten.
nnListening to preset stations
Advanced version
(Auto tuning)
Press MODE to light the “AUTO” indicator on the display, then
use TUNING d or TUNING f to select the station you want to
hear.
wTo tune in manually (Manual tuning)
Press MODE to turn off the display’s “AUTO” indicator, then use
TUNING d or TUNING f to select the station you want to hear.
Your favorite broadcast stations can be preset so that you can tune
them in easily. Up to 56 stations can be preset.
Basic version
FM
nnPresetting radio stations (Manual preset)
Simple version
Tuning in radio stations
Specify a name for the preset broadcast station
(Preset Name) (vpage 41)
23
ENGLISH
Selecting a listening mode (Surround mode)
This unit can play input audio signals in multi-channel surround mode or in stereo mode.
Select a listening mode suitable for the playback contents (cinema, music, etc.) or according to your liking.
Listening Mode
Input audio
signal
nnSurround playback of 2-channel sources
Playback
2-channel
Surround
Multi channel
2-channel
Surround
Multi channel
Listening mode
Standard playback
(vpage 24)
The surround effects suitable for the source type or according to your
liking can be selected from the DENON original sound mode and is used
for playback.
Stereo playback
(vpage 26)
•If multichannel signals are input, they are mixed down to 2-channel audio
and are played.
•Subwoofer signals are also output.
Direct playback
(vpage 26)
Sound recorded in source is played as is.
•Surround back signals or front height signals are not created.
•In this mode, the following items cannot be adjusted.
•Tone (vpage 45)
•MultEQ® (vpage 46)
•Dynamic EQ® (vpage 46)
•Dynamic Volume® (vpage 47)
•RESTORER (vpage 48)
Stereo
Multi channel
2-channel
Stereo
Multi channel
Surround
For 2-channel signal input:
•Surround-channel signals are created and played with surround playback.
For multichannel signal input:
•The surround signal recorded in source is played as surround playback.
(The sound is played according to the settings of the speaker size in
“Speaker Config.” (vpage 49).)
•Surround-back-channel or front-height-channel signals that are not
recorded in source can be created.
DENON original
surround playback
(vpage 26)
2-channel
•Some listening modes cannot be selected, depending on the audio format or number of channels of the input
signal. For details, see “Types of input signals, and corresponding surround modes” (vpage 67).
•Adjust the sound field effect with the menu “Surround Parameter” (vpage 44) to enjoy your favorite sound
mode.
•You can select the listening mode by pressing SURROUND MODE 0 or SURROUND MODE 1 on the main unit.
Press SURROUND MODE 0 or SURROUND MODE 1 and the modes are switched as shown below.
DIRECT
VIRTUAL
24
Standard playback
STEREO
MATRIX
STANDARD
VIDEO GAME
MULTI CH STEREO
MONO MOVIE
ROCK ARENA
JAZZ CLUB
Playing the source (vpage 20 –
1 23).
STANDARD to select the
2 Press
surround decoder to play back
multichannel sound.
•Each time STANDARD is pressed, the surround mode is switched.
Which decoder can be selected depends on the settings of “Amp
Assign” (vpage 49) or “Speaker Config.” (vpage 49).
DOLBY PLgz
z1 This mode is for 7.1-channel surround playback
DOLBY PLgx
z2 This mode is for 7.1-channel or 6.1-channel
DOLBY PLg
This mode is for 5.1-channel surround playback.
Select this mode if no front height speaker nor
surround back speaker is to be used.
•“PLg Cinema”, “PLg Music”, “PLg Game” or
“Pro Logic” is displayed.
DTS NEO:6
This mode is for 7.1-channel, 6.1-channel or
5.1-channel surround playback using the surround
back speakers.
•“DTS NEO:6 Cinema” or “DTS NEO:6 Music” is
displayed.
using the front height speakers.
•“PLgz Height” is displayed.
surround playback using the surround back
speakers.
•“PLgx Cinema”, “PLgx Music”or “PLgx Game”
is displayed.
z1 This can be selected when “Amp Assign” is set to “Front
Height” or “Speaker Config.” – “Front Height” is not set to
“None”.
z2 This can be selected when “Amp Assign” is set to “Normal” or
“Speaker Config.” – “S.Back” is not set to “None”.
ENGLISH
Standard playback
This mode is suited for movie sources.
Music
This mode is suited for music sources. More sound
is sent to the front speakers than in “Cinema”
mode.
Game
This mode is suited for games.
Pro Logic
Height
This mode is suitable for playback of 2-channel
sources recorded with Dolby Pro Logic.
Input signal
DOLBY DIGITAL
(other than 2ch) /
DOLBY DIGITAL EX
DOLBY DIGITAL Plus
z This mode is for the surround decoder “Dolby
PLgz”. If the surround decoder is “Dolby PLgz”,
another mode cannot be selected.
•If the menu “Surround Parameter” – “Front Height” (vpage 45) is
set to “ON”, the mode is switched to “Height” mode.
1
STANDARD to select the
2 Press
surround decoder to play back
Playing the source (vpage 20 –
23).
DTS (5.1ch) /
DTS-ES Discrete 6.1 /
DTS-ES Matrix 6.1 /
DTS 96/24
multichannel sound.
Select the surround mode while viewing the display on the
screen (v“Displaying the currently playing surround mode”
at right).
•Which decoder can be selected depends on the input signal,
the settings of “Amp Assign” (vpage 49) or “Speaker Config.”
(vpage 49).
DTS-HD
PCM (multi ch)
Display
DOLBY
DOLBY
DOLBY
DOLBY
DOLBY
DOLBY
DOLBY
DOLBY
DIGITAL
DIGITAL EX
D
PL x C
D
PL x M
D
PL z
DIGITAL +
D +
EX
D +
PL x C
DOLBY D +
q
w
qShows a decoder to be used.
•A DOLBY DIGITAL Plus decoder is displayed
as “DOLBY D +”.
wShows a decoder that creates sound output
from the surround back speakers.
•“+ PLgz” indicates the front height sound
from front height speakers.
PL x M
For an input signal that can be reproduced in
each surround mode, see “Surround modes and
surround parameters” (vpage 65).
Information
DOLBY D +
PL z
DOLBY TrueHD
DOLBY HD EX
DOLBY HD PL x C
DOLBY HD PL x M
DOLBY HD PL z
DTS SURROUND
DTS
PL x C
DTS
PL x M
DTS
PL z
DTS
NEO:6
DTS ES MTRX6.1
DTS ES DSCRT6.1
DTS 96/24
DTS-HD HI RES
DTS-HD MSTR
DTS-HD
NEO:6
DTS-HD
PL x C
DTS-HD
PL x M
DTS-HD
PL z
DTS Express
MULTI CH IN
MULTI Dolby EX
MULTI IN PL x C
MULTI IN PL x M
MULTI IN PL z
MULTI CH IN 7.1
Advanced version
nnSurround playback of multi-channel sources
(Dolby Digital, DTS etc.)
DOLBY TrueHD
Surround mode
DOLBY DIGITAL
DOLBY DIGITAL EX
DOLBY DIGITAL + PLgx
CINEMA
DOLBY DIGITAL + PLgx MUSIC
DOLBY DIGITAL + PLgz HEIGHT
DOLBY DIGITAL Plus
DOLBY DIGITAL Plus + EX
DOLBY DIGITAL Plus + PLgx
CINEMA
DOLBY DIGITAL Plus + PLgx
MUSIC
DOLBY DIGITAL Plus + PLgz
HEIGHT
DOLBY TrueHD
DOLBY TrueHD + EX
DOLBY TrueHD + PLgx CINEMA
DOLBY TrueHD + PLgx MUSIC
DOLBY TrueHD + PLgz HEIGHT
DTS SURROUND
DTS + PLgx CINEMA
DTS + PLgx MUSIC
DTS + PLgz HEIGHT
DTS + NEO:6
DTS ES MTRX6.1z1
DTS ES DSCRT6.1z2
DTS 96/24z3
DTS-HD HI RES
DTS-HD MSTR
DTS-HD + NEO:6
DTS-HD + PLgx CINEMA
DTS-HD + PLgx MUSIC
DTS-HD + PLgz HEIGHT
DTS Express
MULTI CH IN
MULTI IN + Dolby EX
MULTI IN + PLgx CINEMA
MULTI IN + PLgx MUSIC
MULTI IN + PLgz HEIGHT
MULTI CH IN 7.1
GViews on the displayH
Basic version
Cinema
Displaying the currently playing surround mode
Simple version
3
Select the mode corresponding to the playback
contents with the menu “Surround Parameter” –
“Mode” (vpage 44) to enjoy your favorite sound
mode.
z1 This is displayed when the input signal is “DTS-ES Matrix 6.1” and this unit’s “AFDM”
(vpage 44) setting is “ON”.
z2 This is displayed when the input signal is “DTS-ES Discrete 6.1”.
z3 This is displayed when the input signal is “DTS 96/24”.
25
ENGLISH
DENON original surround playback
the source (vpage 20 –
1 Playing
23).
Press SIMULATION to select the
2 surround
mode.
•Each time SIMULATION is pressed, the
surround mode is switched.
MULTI CH
STEREO
This mode is for enjoying stereo sound from all
speakers.
Stereo playback
This is the mode for playing in stereo. The tone can be adjusted.
•Sound is output from the front left and right speakers and subwoofer.
•If multichannel signals are input, they are mixed down to 2-channel
audio and are played.
Playing the source (vpage 20 –
1 23).
2 Press D/ST to select “STEREO”.
Stereo playback begins.
ROCK ARENA
This mode is for enjoying the atmosphere of a live
concert in an arena.
JAZZ CLUB
This mode is for enjoying the atmosphere of a live
concert in a jazz club.
MONO MOVIE z This mode is for playing monaural movie sources
with surround sound.
VIDEO GAME
This mode is suited for achieving surround sound
with video games.
MATRIX
This mode lets you add a spacious feel to stereo
music sources.
VIRTUAL
This mode is for enjoying surround effects using
only the front speakers or headphones.
z When playing sources recorded in monaural in the “MONO
MOVIE” mode, the sound will be off balance with a single
channel (left or right), so input to both channels.
Direct playback
Sound recorded in source is played as is.
•Surround back signals or front height signals are not created.
•In this mode, the following items cannot be adjusted.
•Tone (vpage 45)
•MultEQ® (vpage 46)
•Dynamic EQ® (vpage 46) •Dynamic Volume® (vpage 47)
•RESTORER (vpage 48)
Playing the source (vpage 20 –
1 23).
2 Press D/ST to select “DIRECT”.
Direct playback begins.
Depending on the program source being played, it may not be possible
to achieve a satisfactory surround effect. In this case, try other modes
to achieve a sound field suited to your tastes.
NOTE
When the input signal is Dolby TrueHD, Dolby Digital Plus, DTS-HD
or DTS Express, you cannot select DENON original surround mode.
26
ENGLISH
Simple version
Advanced
version
Advanced version
Here, we explain functions and operations that let you make better use of this unit.
Basic version
F Speaker installation/connection (Other than 5.1-channel) vpage 28
F Playback (Advanced operation) vpage 32
F Playback in ZONE2 (Separate room) vpage 34
F How to make detailed settings vpage 36
F Operating the connected devices by remote control unit vpage 56
Advanced version
Information
27
ENGLISH
Speaker installation/connection (Other than 5.1-channel)
Here we describe the installation, connection and setup methods for speakers other than 5.1-channel speakers. For the installation, connection and setup methods
for 5.1-channel speakers, see “Simple version (Simple setup guide)” (vpage 3).
When 7.1ch (Front height speaker) installed
Procedure for speaker settings
Install
FHL
When 6.1ch (Surround back speaker) installed
FHR
FL
FR
FL SW
Connect (vpage 29)
FR
SW
C
C
z2
z1
z2
z1
z3
Set up speakers (vpage 31)
SL
SL
SR
Install
SR
Listening position
This unit is compatible with Dolby Pro Logic gz (vpage 69),
which offers an even wider and deeper surround sensation.
When using Dolby Pro Logic gz, install front height speakers.
Listening position
SB
z1 22˚ – 30˚
z2 22˚ – 45˚
z3 90˚ – 110˚
z1 22˚ – 30˚
When 7.1ch (Surround back speaker) installed
z2 90˚ – 110˚
When Front A/B speakers installed
Install the surround back speakers in a position 2 to 3 ft (60 to 90 cm)
higher than ear level.
Front height
speaker
•Point slightly
downwards
At least
3.3 ft / 1 m z
Surround
speaker
FL
FR
SW
FL(B) FL(A)
SW
C
2 – 3 ft /
60 – 90 cm
Front
speaker
Surround back
speaker
•Point slightly
downwards
GViewed from the sideH
z1
z2
z3
SL
SR
Listening
position
zRecommended
z
for Dolby Pro Logic gz
NOTE
SBL
SBR
It is not possible to use the surround back speakers and front height
speakers simultaneously.
z1 22˚ – 30˚
28
FR(A) FR(B)
z2 90˚ – 110˚
z3 135˚ – 150˚
Listening position
FL
FR
C
SW
SL
SR
Front speaker (L)
Front speaker (R)
Center speaker
Subwoofer
Surround speaker (L)
Surround speaker (R)
SBL
SBR
FHL
FHR
Surround back speaker (L)
Surround back speaker (R)
Front height speaker (L)
Front height speaker (R)
ENGLISH
7.1-channel/6.1-channel (Surround back speaker) connection
For 7.1-channel (Surround back speaker) playback, set “Amp Assign” in “Set up speakers” (vpage 31) to
“Normal”.
•For the method of connecting 5.1-channel speakers, see page 4.
•For the method of connecting the TV, see page 5.
7.1-channel (Front height speaker) connection
For 7.1-channel (Front height speaker) playback, set “Amp Assign” in “Set up speakers” (vpage 31) to
“Front Height”.
Simple version
Connect
Basic version
Advanced version
FL
FR
SW
C
FHL
FHR
FL
FR
SW
SL
SR
C
SR
If using only one surround back speaker
(with a 6.1-channel connection), connect
it to the “L” side of the SURR. BACK/
AMP ASSIGN terminal.
For speaker settings in this case, see
“When 6.1ch (Surround back speaker)
installed” (vpage 28).
For speaker impedance and speaker cable connections, see page 4.
SBL
Information
6.1-channel connection
SL
SBR
29
ENGLISH
Connect
Front A/B connection
2.1-channel/2-channel connection
The second set of front speakers can be connected to the SURR.
BACK/AMP ASSIGN terminals.
In this case, set “Amp Assign” of “Set up speakers” (vpage 31) to
“Front B”.
Bi-amp connection
A bi-amp connection is to connect separate amplifiers to the tweeter
terminals and woofer terminals of speakers compatible with the
bi-amp function. This prevents the back electromotive force (returned
force without output) of the woofer sent to the tweeter, which affects
the sound quality of the tweeter, and you can enjoy playback with
higher-quality sound.
In this case, set “Amp Assign” of “Set up speakers” (vpage 31) to
“Front Bi-Amp”.
FL
FR
SW
q
w
q
FL
(L)
For 2-channel playback, disconnect the
subwoofers.
FR(A) FR(B)
For surround playback of a multichannel source, if you connect the
center speaker, surround speakers and subwoofers, 5.1-channel
playback is available.
Front speakers can be used separately, depending on the speaker’s
specifications or playback source such as front speakers (A) for
multichannel playback and front speakers (B) for 2-channel playback
(vpage 51 “Front Speaker Setup”).
30
(R)
2-channel connection
SW
FL(B) FL(A)
w
FR
When making a bi-amp connection, the same signal is output from the
front speaker terminal and the SURR.BACK/AMP ASSIGN terminal.
For surround playback of a multichannel source, if you connect the
center speaker, surround speakers and subwoofers, 5.1-channel
playback is available.
NOTE
•Use speakers compatible with bi-amp connections.
•When making bi-amp connections, be sure to remove the shortcircuiting plate or wire between the speaker’s woofer and tweeter
terminals.
For speaker impedance and speaker cable connections, see page 4.
ENGLISH
Set up speakers
around items indicate the settings.
Simple version
Here we describe how to set up speakers other than 5.1-channel speakers.
For the method of setting up 5.1-channel speakers, see “Simple version”, “Set up speakers (Audyssey® Auto Setup)” (vpage 6).
First install and connect the speakers to this unit.
1
Set up
the remote control unit
2 Connect the setup microphone.
to page 8
o p to select the configuration
4 Use
6 Proceed
“ Preparation ” step 5.
of the connected speakers.
Normal
ZONE2
The “MAIN” indicator lights.
When the setup microphone is
connected, the following screen is
displayed.
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
nn Set up the operation mode
Press AMP to set the remote control
unit to amplifier operation mode.
Front Bi-Amp
Amp Assign:
ZONE2
Start
Cancel
[ENT]:Select [RTN]:Back
3 Use ui to select “Amp Assign”.
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Amp Assign:
ZONE2
Start
Cancel
[RTN]:Back
Front B
5
GWhen “Front B” is selected in
step 4H
A
Select this to use front speaker A.
B
Select this to use front speaker B.
NOTE
After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
Advanced version
Press ZONE SELECT
Front Height
Set when using 7.1-channel
(Front/Center/Surround/Surround
Back/Subwoofer) speakers.
Set for connecting the speakers
for ZONE2 to the SURR. BACK/
AMP ASSIGN terminals.
Set for connecting the front
height speakers to the SURR.
BACK/AMP ASSIGN terminals.
Set for connecting a tweeter of
a front speaker to the SURR.
BACK/AMP ASSIGN terminals
and a woofer of the front speaker
to the FRONT terminals.
Set for connecting the second set
of front speakers to the SURR.
BACK/AMP ASSIGN terminals. In
this case, go to step 5.
Basic version
nn Set up the zone mode
Press ZONE SELECT to switch the
zone mode to “MAIN”.
qUse ui to select “Front Sp.”.
wPress o p to select a speaker.
A+B
Select this to use front speakers A and B
simultaneously.
Press AMP
Information
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
31
ENGLISH
Playback (Advanced operation)
Playback (Basic operation) (vpage 19)
Selecting a listening mode (Surround mode)
(vpage 24)
nn HDMI control function (vpage 32)
nn Sleep timer function (vpage 33)
nn Adjusting the volume of the speakers (vpage 33)
nn Quick select function (vpage 34)
nn Various memory functions (vpage 34)
Convenient functions
HDMI control function
When you make an HDMI connection with a TV or player compatible
with this unit and HDMI control functions, you can perform the
following operations by setting the HDMI control function of each
device.
nn This unit power off can be linked to the TV power off
step.
nn You can switch audio output devices with a TV
operation.
When you set “Output audio from amp” in the TV audio output
setup operation, you can switch the amp power on.
nn You can adjust this unit volume in the TV volume
adjustment operation.
nn You can switch this unit input sources through
linkage to TV input switching.
nn When playing the player, this unit input source
switches to the source for that player.
NOTE
•When “HDMI Control” is set to “ON”, it consumes more
standby power.
•The HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
•Some functions may not operate depending on the connected TV
or player. Check the owner’s manual of each device for details
beforehand.
•When “Power Off Control” on the menu is set to “OFF” (vpage 51),
this unit is not set to standby even if the connected device is in the
standby mode.
•When connection changes are implemented, such as adding
connections to HDMI devices, linked operations may be initialized.
In this case, you will need to reconfigure the settings.
•When “HDMI Control” is set to “ON”, it is not possible to assign an
HDMI connector to “TV” at “Input Assign” (vpage 41).
32
the HDMI output connector corresponding with
1 Set
the HDMI control function.
Set “HDMI Control” (vpage 51) to “ON“.
the power on for all the equipment connected
2 Turn
by HDMI cable.
the HDMI control function for all equipment
3 Set
connected by HDMI cable.
•Please consult the operating instructions for the connected
equipment to check the settings.
•Carry out steps 1 and 2 should any of the equipment be unplugged.
the television input to the HDMI input
4 Switch
connected to this unit.
this unit input to the HDMI input source and
5 Switch
check if the picture from the player is ok.
you turn the TV’s power to standby, check
6 When
that the power of this unit also goes to standby.
If the HDMI control function does not operate properly, check the
following points.
•Is the TV or player compatible with the HDMI control function?
•Is “HDMI Control” (vpage 51) set to “ON”?
•Is “Power Off Control” (vpage 51) set to “All” or “Video”?
•Are the HDMI control function settings of all equipment correct?
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat steps 2 and 3.
•“Input Assign” – “HDMI” (vpage 41) setting has changed.
•There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
ENGLISH
Convenient functions
Adjusting the volume of the speakers
The power automatically goes into standby once the set time has
elapsed.
This is convenient for playing sources while going to sleep.
You can adjust the channel level either according to the playback
sources or to your taste, as described below.
Press SLEEP and display the time you
want to set.
Press ZONE SELECT to switch the
1 zone
mode to “MAIN”.
The “SLEEP” indicator on the display lights.
The “MAIN” indicator lights.
120
110
Press AMP to set the remote
2 control
unit to amplifier
10 min
20
30
40
100
90
80
70
50
60
operation mode.
The “MAIN” indicator lights.
Press AMP to set the remote
2 control
unit to amplifier
3 Press CH LEVEL.
Channel Level
Press SLEEP to set “OFF”.
The “SLEEP” indicator on the display turns off.
FL
C
FR
SW
[
0.0dB
0.0dB
0.0dB
0.0dB
SR
SBR
SBL
SL
Channel Level
0.0dB
0.0dB
0.0dB
0.0dB
Fader
FRONT : REAR
]:CH Sel.
4 Use ui to select the speaker.
The speaker that can be set switches
each time one of the buttons is pressed.
5
Use o p to adjust the volume.
•In the case of a subwoofer, pressing o when it is at “–12 dB” will
change the setting to “OFF”.
When a headphone jack is inserted, the headphone channel level can
be adjusted.
FL
C
FR
SW
[
0.0dB
0.0dB
0.0dB
0.0dB
SR
SBR
SBL
SL
0.0dB
0.0dB
0.0dB
0.0dB
Advanced version
•The sleep timer setting is canceled if this unit’s power is set to
standby or turned off.
•When power to the main zone is
turned off with the sleep timer,
power in ZONE2 is also turned off.
•If SLEEP on the main unit is pressed,
the same function as with the
remote control unit can be obtained.
Press ZONE SELECT to switch the
1 zone
mode to “MAIN”.
operation mode.
3 Press CH LEVEL.
To cancel the sleep timer
This function lets you adjust (fade) the sound all at once from the
front (front speaker / front height speaker / center speaker) or rear
(surround speaker / surround back speaker).
Basic version
•The time switches as shown below each
time SLEEP is pressed.
OFF
nnAdjusting the volume of the different speakers
nnAdjusting the volume of groups of speakers
(Fader function)
Simple version
Sleep timer function
Fader
FRONT : REAR
]:CH Sel.
i to select “Fader”, then
4 Use
select the item to be adjusting
using o p.
5 Use o p to adjust the volume of the speakers.
(o : front, p: rear)
•The fader function does not affect the subwoofer.
•The fader can be adjusted until the volume of the speaker is adjusted
to the lowest value of -12 dB.
Information
33
ENGLISH
Convenient functions
Quick select function
All of the settings in step 1 can be memorized together. By memorizing
frequently used settings, you can quickly access and enjoy a playback
environment that is consistently the same.
nnSaving the settings
1 Set the items below to the settings you want to save.
q Input source (vpage 19)
w Volume (vpage 20)
e Surround mode (vpage 24)
r Video Select (vpage 42)
t Audyssey Setting
(MultEQ®, Dynamic EQ®, Dynamic
Volume®) (vpage 46)
2
NOTE
Press and hold the desired QUICK SELECT until
“Memory” appears on the display.
The current settings will be memorized.
QUICK SELECT 1
QUICK SELECT 2
QUICK SELECT 3
GQuick Select DefaultsH
Input Source
BD
SAT/CBL
DOCK
nnRecalling the settings
Press QUICK SELECT at which the
settings you want to call out are saved.
The
,
the display.
or
indicator illuminates on
•The Quick Select function can be set separately for the different
zones (vpage 35 “Quick select function”).
•If QUICK SELECT on the main unit
is pressed, the same function as
with the remote control unit can be
obtained.
Volume
–40 dB
–40 dB
–40 dB
Playback in ZONE2
(Separate room)
•You can operate this unit so as to enjoy audio in a different room
(ZONE2) other than the MAIN ZONE (room where the unit is located).
•You can simultaneously play back the same source in both the MAIN
ZONE and ZONE2. You can also play back separate sources in the
MAIN ZONE and ZONE2.
Audio output
Input sources stored with the quick select function cannot be selected
if they have been deleted at “Source Delete” (vpage 53). In this case,
store them again.
ZONE2 playback by speaker output
Various memory functions
The ZONE2 audio signals are output from this unit’s SURR. BACK/
AMP ASSIGN speaker terminals using the amplifier assignment
function.
nnPersonal memory plus function
nnConnecting and setting the speakers
This function sets the settings (input mode, surround mode, HDMI
output mode, MultEQ, Dynamic EQ, Dynamic Volume, audio delay
etc.) last selected for the individual input sources.
“Amp Assign” setting
(vpage 49) and audio
signals output
Connecting the speakers
MAIN ZONE
The surround parameters, tone settings and the volumes of the
different speakers are stored for the individual surround modes.
nnLast function memory
This unit
This function stores the settings which were made before going
into the standby mode.
When the power is turned back on, the settings are restored.
ZONE2
Output signal :
Stereo (L / R)
ZONE2
Naming quick select settings
See “Quick Select Name” (vpage 54).
We recommend using high quality pin-plug cables for audio
connections in order to prevent noise.
NOTE
It is not possible to play the digital audio signals input from the HDMI,
COAXIAL or OPTICAL connectors in ZONE2.
34
ENGLISH
Quick select function
Use VOL df to adjust the volume.
2
ZONE/DEVICE ON to turn
3 Press
on the ZONE2 power.
GAdjustable rangeH – – – –80dB – –40dB – 18dB
(When the “Volume Display” (vpage 53) setting is “Relative”)
GAdjustable rangeH
0 – 41 – 99
(When the “Volume Display” (vpage 53) setting is “Absolute”)
•At the time of purchase, “Volume Limit” (vpage 53) is set to
“–10dB (71)”.
Adjusting the volume
The remote control unit switches to the
operating mode for ZONE2.
Press AMP.
The
indicator on the display lights.
•Also, pressing any of input source select
button in standby mode turns on the power.
•When ZONE/DEVICE OFF is pressed, ZONE2
turns off.
•Power in ZONE2 can be turned on or off by
pressing ZONE2 ON/OFF on the main unit.
4
Input source
select buttons
Press the input source select button.
The audio signal of the selected source is output to ZONE2.
nnSaving the settings
the items below to the settings
1 Set
you want to save.
q Input source (vpage 35)
w Volume (vpage 35)
Switch ZONE SELECT to
2 “ZONE2”.
The remote control unit switches to the
operating mode for ZONE2.
Turning off the sound temporarily
Press MUTE.
The sound is reduced to the level set at “Mute Level” (vpage 53) in
the menu.
•To cancel, either adjust the volume or press MUTE again.
•The setting is canceled when the zone’s power is turned off.
and hold the desired QUICK SELECT button until
3 Press
“Memory” appears on the display.
The current settings will be memorized.
QUICK SELECT 1
QUICK SELECT 2
QUICK SELECT 3
GQuick select defaultsH
Input Source
BD
SAT/CBL
DOCK
Advanced version
•Turn SOURCE SELECT after
pressing ZONE2 SELECT on
the main unit to select an input
source.
Turn MASTER VOLUME after pressing ZONE2 SELECT on the main
unit to adjust the sound volume.
It is also possible to save three settings for ZONE2.
Basic version
1 Switch ZONE SELECT to “ZONE2”.
Simple version
Playback
Volume
–40dB
–40dB
–40dB
nnRecalling the settings
Switch ZONE SELECT to
1 “ZONE2”.
When power for both MAIN ZONE and ZONE2 is set to ON, power of
the MAIN ZONE only can be turned off. Select “MAIN” in step 1 then
press ZONE/DEVICE OFF.
The remote control unit switches to the
operating mode for ZONE2.
QUICK SELECT at which the
2 Press
settings you want to call out are
saved.
Information
Naming quick select settings
See “Quick Select Name” (vpage 54).
35
ENGLISH
How to make detailed settings
Menu map
For menu operation, connect a TV to this unit and
display the menu on the TV screen. For menu
operations, see the following page.
MENU
1.Audio Adjust
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
Setting items
1. Audio Adjust
1.Audio Adjust
1.Surround Parameter
2.Tone
3.Audyssey Settings
4.Manual EQ
5.RESTORER
6.Audio Delay
[ENT]:Select [RTN]:Back
2. Information
2.Information
1.Status
2.Audio Input Signal
3.HDMI Information
4.Auto Surround Mode
5.Quick Select
6.Preset Channel
[ENT]:Select [RTN]:Back
[ENT]:Select
Items that only need to be set
once
Set these for example upon purchase.
Once these items are set, there is
no need to set them again unless
the speaker layout or the connected
speakers have been changed.
3. Auto Setup
Number
Detailed items
1-1
1-2
1-3
1-4
1-5
Surround Parameter
Tone
Audyssey Settings
Manual EQ
RESTORER
1-6
Audio Delay
2-1
2-2
2-3
Status
Audio Input Signal
HDMI Information
2-4
2-5
2-6
Auto Surround Mode
Quick Select
Preset Channel
3-1
Audyssey Auto Setup
3-2
4-1
4-2
4-3
4-4
4-5
Adjuts surround sound parameters.
Adjuts the tonal quality of the sound.
Makes MultEQ®, Dynamic EQ® and Dynamic Volume® settings.
Uses the graphic equalizer to adjust the tone of each speaker.
Uncompresses compressed sources and apply bass boost for richer
sound.
Compensates for incorrect timing between video and audio.
Shows information about current settings.
Shows information about audio input signals.
Displays the HDMI input/output signals and HDMI monitor
information.
Displays the settings stored for the auto surround mode.
Displays the settings stored for the Quick Select function.
Shows information about tuner preset channels.
Page
44
45
46
47
48
48
55
55
55
55
55
55
Parameter Check
Makes the optimum settings for the speakers being used
automatically.
Checks Audyssey Auto Setup measurement results.
This item is only displayed after Audyssey Auto Setup procedure has
been performed.
10
Speaker Setup
HDMI Setup
Audio Setup
ZONE2 Setup
Option Setup
Sets the speaker size and distance, the channel level, etc.
Makes settings for HDMI video/audio output.
Makes settings for audio playback.
Makes settings for audio playback in a ZONE2 system.
Makes various other settings.
49
51
52
53
53
Auto Preset
Preset Skip
Uses the auto preset function to program radio stations.
Sets the preset memories that you do not want to display when
tuning.
Assigns name to a preset memory.
Changes input connector assignment.
Makes the video settings.
Sets the audio input mode and decode mode.
Changes the display name for this source.
Adjusts the playback level of the audio input.
Makes settings for iPod playback.
40
40
3.Auto Setup
1.Audyssey Auto Setup
2.Parameter Check
Description
6
[ENT]:Select
4. Manual Setup
4.Manual Setup
1.Speaker Setup
2.HDMI Setup
3.Audio Setup
4.ZONE2 Setup
5.Option Setup
[ENT]:Select [RTN]:Back
5. Input Setup
(Example: TUNER)
5.Input Setup
1.Auto Preset
2.Preset Skip
3.Preset Name
4.Video
5.Rename
6.Source Level
TUNER
[ENT]:Select [RTN]:Back
Displayed items of the “Input Setup” menu differs,
depending on the selected input source.
36
–
Preset Name
Input Assign
Video
Input Mode
Rename
Source Level
Playback Mode
41
41
42
42
43
43
43
ENGLISH
Simple version
Examples of on-screen display and front display
Below we describe typical examples of displays on the TV screen and on the set’s display window.
On-screen Display
Top menu display
Front Display
Description
MENU
q
Adjust
w 1.Audio
2.Information
e
3.Auto Setup
4.Manual Setup
5.Input Setup
Audio Adjust
Basic version
w
e
q The menu items are displayed here.
w The selected line is displayed here.
The currently selected item is displayed on the display.
Use ui to move to the item you want to set.
e The number of the current selected setting menu is displayed.
[ENT]:Select
Display when changing settings
5-1.Input Assign
qDefault
HDMI Digi
BD
DVD
TV
SAT/CBL
GAME
V.AUX
1
2
3
4
w
e [ENT]:Select
q The number of the current selected setting menu is displayed.
w Use uio p to move to the item you want to set.
e Press ENTER to set to the mode in which the setting can be made.
Comp
01
C1
1
[RTN]:Back
q
BD
5-1.Input Assign
qDefault
HDMI Digi
BD
DVD
TV
SAT/CBL
GAME
V.AUX
1
2
r -3
4
w
Press ENTER.
r 0 1 is displayed at the sides of item whose setting can be changed.
Use o p to change to the desired setting.
Comp
BD
01
C1
•HDMI1 –
r
1
Advanced version
Press ENTER.
[HDMI1 ]
[ENT]:Select [RTN]:Back
Display when inputting characters
e 5-4.Rename
DVD
: DVD
Default
[SFT]:a/A
[ENT]:OK
w
DVD
w
•DVD
e
–
q
For inputting characters on a keyboard screen or with the number buttons
on the remote control unit, see page 38.
[SRCH]:KeyBD
[RTN]:Cancel
w
5-4.Rename
DVD
:[DVD
q When o p is pressed, the cursor moves to the left or right.
w When ui is pressed at the position where you want to input the
character, the character is input.
e The number of the current selected setting menu is displayed.
Default
q
Information
Display when resetting
q
q Press i to select “Default”, then press ENTER to set.
w The number of the current selected setting menu is displayed.
]
q Default
Press ENTER.
w
[ ]:Up/Down
[ENT]:Select [RTN]:Back
Default? : • No
37
ENGLISH
Inputting characters
“Preset Name” (vpage 41), “Rename” (vpage 43), “Zone Rename”
(vpage 54) and “Quick Select Name” (vpage 54)can be changed as
desired.
For inputting characters, there are three methods, as shown below.
Method for inputting characters
Method
Operations
•Operating with the remote control unit.
Using the number
•Multiple characters are assigned to
buttons
a button, and each time the button is
(normal screen)
pressed, a character is switched.
•Operating with the remote control unit
or the main unit.
Using the cursor buttons
•Use uio p and ENTER to input
(normal screen)
characters.
Using the keyboard
screen
•Operating with the remote control unit.
•Select a character on the TV screen to
input characters.
Normal screen
nnDisplay of a normal input screen
5-4.Rename
DVD
Default
e
[SFT]:a/A
[ENT]:OK
: DVD
q
w
[SRCH]:KeyBD
[RTN]:Cancel
q Cursor
w Character input section
e Guide for operation buttons
Switching upper- and lower-case characters
•[SFT] SHIFT
•[SRCH] SEARCH Switching to the keyboard screen input
method
Registering an input character
•[ENT] ENTER
Canceling an input character
•[RTN] RETURN
38
Using the number buttons
Example: For changing the input source from “DVD” to “DENON”
1
the cursor at the character to be changed with
2 Place
o p and press the number button (0 – 9) until the
qPlace the cursor at “V”.
DVD
wPress
twice.
“V” changes to “E”.
DED
Display the screen for inputting characters.
(vpage 36 “Menu map”)
desired character is displayed.
•The types of characters that can be input are as shown below.
1-./:
MNOmno6
ABCabc2
PQRSpqrs7
DEFdef3
TUVtuv8
GHIghi4
WXYZwxyz9
JKLjkl5
0 (Space) ’ ( ) z + ; < = > ? [ ]
•The input character type can be switched
by pressing SHIFT while the display name
is being changed.
•For entering the characters assigned to one
number button continuously, press p to
move the cursor to the right after entering
a character then enter the next character.
•For entering characters assigned to
separate buttons, press the number button
continuously. The cursor automatically
moves to the next position, and the input
character is registered.
step 2 to change the name then press ENTER
3 Repeat
to register it.
twice.
ePress
“E” is automatically registered, and “D” changes
to “N”.
rPress p.
“N” is registered.
DEN
DEN
three times.
tPress
Input “O”.
yPress p.
“O” is registered.
DENO
twice.
uPress
Input “N”.
iPress ENTER to register the input source name.
DENON
DENO
Using the cursor buttons
the screen for inputting characters.
1 Display
(vpage 36 “Menu map”)
o p to set the cursor to the
2 Use
character you want to change.
ui to change the character,
3 Use
then press ENTER.
•The types of characters that can be input are
as shown below.
GUpper case charactersH
ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH
abcdefghijklmnopqrstuvwxyz
GSymbolsH ’ ( ) z + – . / : ; < = > ? [ ]
GNumbersH 0123456789 (Space)
•The input character type can be switched by pressing SHIFT while
the display name is being changed.
Repeat steps 2 and 3 to rename then press ENTER to
4 register
it.
ENGLISH
Inputting characters
1
2 Press SEARCH while a normal screen is displayed.
a character to be changed.
3 Select
qPress uio p to select “[ ]” or “[ ]”.
Display the screen for inputting characters.
(vpage 36 “Menu map”)
nnDisplay of a keyboard input screen
q
w
t
y
[DVD
A keyboard screen is displayed.
]
ABCDEFGHIJKLMNOPQRST
UVWXYZ’()*+-./:;<=>?
[a/A] [SP] [ ] [ ] [OK]
[SFT]:a/A [SRCH]:Normal
[ENT]:Input [RTN]:Cancel
u
i
o
Each time ENTER is pressed, the cursor moves by one
character.
4
Select a character to be input with
uio p then press ENTER.
ZONE SELECT to switch the
1 Press
zone mode to “MAIN”.
The “MAIN” indicator lights.
Press AMP to set the remote
2 control
unit to amplifier
operation mode.
3 Press MENU.
ui to select the menu to
4 Press
be set or operated.
5 Press ENTER to enter the setting.
The menu is displayed on the TV screen.
•The types of characters that can be input are
as shown below.
GUpper case characters/SymbolsH
ABCDEFGHIJKLMNOPQRST
UVWXYZ ’ ( ) z + - . / : ; < = > ?
GLower case characters/NumbersH
abcdefghijklmnopqrst
uvwxyz[ ]0123456789
Advanced version
q Cursor
w Character input section
e Cursor
r Keyboard section
t Upper (Symbols)- / lower (Numbers)-case character switching key
y Space key
u OK key
i Cursor keys
o Guide for operation buttons
Switching upper- and lower-case characters
•[SFT] SHIFT
•[SRCH] SEARCH For switching to the normal screen input
method
For inputting a selected character
•[ENT] ENTER
Canceling an input character
•[RTN] RETURN
wPress ENTER to place the cursor at the character
to be changed.
Menu operation
Basic version
e
r
5-4.Rename
Input Setup
Perform settings related to input source playback.
•You do not have to change the settings to use the unit. Make
settings when needed.
Simple version
Keyboard screen
•To return to the previous item, press RETURN.
•Exiting the Menu, press MENU while the menu is displayed.
The menu display disappears.
5 Repeat steps 3 and 4 to rename.
6 Use uio p to select “[OK]”, then press ENTER.
Information
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
39
ENGLISH
Input Setup
Important information
Items that can be set with the Input Setup procedure
Auto Preset (vpage 40)
Preset Skip (vpage 40)
5-1.Auto Preset
Auto Tuning
Preset Station Memory
Storing Preset Memory
Start
[ENT]:Start [RTN]:Back
5-2.Preset Skip
Block
:
A Block Presets:
A1 FM 87.50MHz :
A2 FM 89.10MHz :
A3 FM 98.10MHz :
A4 FM107.90MHz :
A5 FM 90.10MHz :
A6 FM 90.10MHz :
A7 FM 90.10MHz :
A8 FM 90.10MHz :
Input Assign (vpage 41)
Video (vpage 42)
5-1.Input Assign
Default HDMI Digi Comp
BD
DVD
TV
SAT/CBL
GAME
V.AUX
1
2
3
4
O1
C1
A
ON
ON
ON
ON
ON
ON
ON
ON
ON
Preset Name (vpage 41)
5-3.Preset Name
Block: A
A1FM 87.50MHz:
A2FM 89.10MHz:
A3FM 98.10MHz:
A4FM107.90MHz:
A5FM 90.10MHz:
A6FM 90.10MHz:
A7FM 90.10MHz:
A8FM 90.10MHz:
[ENT]:Select [RTN]:Back
Input Mode (vpage 42)
5-2.Video
5-3.Input Mode
Video Select: Source
Video Mode : Auto
Input Mode
Decode Mode
: Auto
: Auto
In this section, the configurable input sources for each item are shown as follows.
BD
DVD
TV
SAT/CBL
[ENT]:Select [RTN]:Back
[RTN]:Back
Rename (vpage 43)
Source Level (vpage 43)
5-4.Rename
5-5.Source Level
BD
Source Level(A):
Source Level(D):
[RTN]:Back
Playback Mode (vpage 43)
5-6.Playback Mode
0dB
0dB
Repeat Mode
Shuffle Mode
: OFF
: OFF
GAME
V.AUX
DOCK
TUNER
NOTE
Input sources that have been set to “Delete” at “Source Delete” (vpage 53) cannot be selected.
Auto Preset
Use the auto preset function to program radio stations.
Setting items
Start
Start the auto preset
process.
1
: BD
nnAbout the display of input sources
Setting details
If an FM station cannot be preset automatically, select the desired
station by tuning it in manually, then preset it manually.
TUNER
Preset Skip
Default settings are underlined.
Set preset ch to be skipped when selecting.
Default
[
]:Up/Down [ ]:Rename
[RTN]:Back
[RTN]:Back
[RTN]:Back
Setting items
Setting details
A–G
Set the preset channels you
do not want to display. You
can set by preset memory
block (A to G) or by preset
channel (1 to 8).
1 – 8 : Set by individual preset channels in the currently selected preset
memory block.
•ON : Display the selected preset channel.
•Skip : Do not display the selected preset channel.
If you set “Block Presets” to “Skip”, you can skip the preset memory
blocks (A to G).
TUNER
40
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
ENGLISH
Input Setup
Setting items
Assign a name to a preset memory.
Setting items
A1 – G8
Select the preset channel.
Setting details
•Up to eight characters can be input.
•For character input, see page 38.
TUNER
Examples of input assign menu screen displays
5-1.Input Assign
Default HDMI Digi Comp
1
2
3
4
O1
C1
1
w
e
r
[ENT]:Select [RTN]:Back
Input assignments menu operations
Input
source
BD
DVD
TV
SAT/
CBL
GAME
V.AUX
DOCK
Default
setting
HDMI
1
HDMI
2
None
HDMI
3
HDMI
4
None
None
•An input source to which an HDMI input connector cannot be assigned
is displayed as “–”.
•To play the video signal assigned at “HDMI” combined with the audio
signal assigned at “Input Assign“ – “Digital”, select “Digital” at “Input
Mode” (vpage 42).
•The audio signals input from the analog and digital connectors are not
output to the monitor.
•Even if HDMI input connector is assigned to the input source “DOCK”,
“DOCK” is effective when a control dock for iPod is connected.
•When “HDMI Control” (vpage 51) is set to “ON”, HDMI input connector
cannot be assigned to “TV”.
C1 (COAXIAL) / O1 (OPTICAL)
Digital
Set this to change the digital None : Do not assign a digital input connector to the selected input source.
input connectors assigned
•At time of purchase, the settings of the different input sources are as
to the input sources.
shown below.
BD
DVD
TV
Input source
BD
DVD
TV
SAT/CBL
GAME
SAT/CBL
GAME
V.AUX
DOCK
1
Press ENTER, then use o p to select the input connector to be
2 assigned.
3 Press ENTER to enter the setting.
Use uio p to move the highlight to the item you want to set.
Default
setting
None
None
Input source
V.AUX
DOCK
Default
setting
None
None
OPTICAL
1
COAXIAL
1
None
Information
NOTE
If all “HDMI”, “Digital” and “Component” assignment of the Game source are set to “None”, Game
source cannot be selected with the input source selection.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Advanced version
BD
DVD
TV
SAT/CBL
GAME
V.AUX
q Input Source
w HDMI input
e Digital audio input
r Component video input
GAME
DOCK
Basic version
V.AUX
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Input Assign
q
HDMI
HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4
Set this to change the HDMI None : Do not assign an HDMI input connector to the selected input
input connectors assigned
source.
to the input sources.
•At time of purchase, the settings of the different input sources are as
shown below.
BD
DVD
TV
SAT/CBL
Default
The changed preset name
is returned to the default
setting.
Setting details
Simple version
Preset Name
Confirm the setting
Return to previous menu
41
ENGLISH
Input Setup
Setting items
Component
Set this to change the
component video input
connectors assigned to the
input sources.
BD
DVD
SAT/CBL
V.AUX
TV
GAME
DOCK
Default
The “Input Assign” settings
are returned to the default
settings.
Setting details
Setting items
Comp1 (Component video)
None : Do not assign a component video input connector to the selected
input source.
•At time of purchase, the settings of the different input sources are as
shown below.
Input source
Default
setting
BD
DVD
TV
None None None
SAT/
CBL
GAME
V.AUX
DOCK
Component
1
None
None
None
•An input source to which an component video input connector cannot be
assigned is displayed as “–”.
•Even if a component input connector is assigned to the input source
“DOCK”, “DOCK” is effective when a control dock for iPod is connected.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
If you select “Default” and press ENTER, the message “Default
Setting?” is displayed. Select “Yes” or “No”, and then press ENTER.
Video
Setting details
Video Mode
Make settings for video
processing.
BD z DVD
SAT/CBL
V.AUX
TV
z
GAME z
DOCK
Input Mode
The input modes available for selection may vary depending on the input source.
Setting items
Auto : Automatically detect input signal and perform playback.
HDMI : Play only signals from HDMI input.
Digital : Play only signals from digital input.
Analog : Play only signals from analog input.
Decode Mode
Set the decode mode for
input source.
•“HDMI” can be set for input sources for which “HDMI” is assigned at
“Input Assign” (vpage 41).
•“Digital” can be set for input sources for which “Digital” is assigned at
“Input Assign” (vpage 41).
•If the input source is set to “TV” or “Game”, it cannot be set to “Analog”.
•When digital signals are properly input, the
indicator lights on
the display. If the
indicator does not light, check the digital input
connector assignment and the connections.
•If “HDMI Control” is set to “ON” and a TV compatible with the ARC is
connected via the HDMI MONITOR connectors, the input mode whose
input source is “TV” is fixed to ARC.
Auto : Detect type of digital input signal and decode and play automatically.
PCM : Decode and play only PCM input signals.
DTS : Decode and play only DTS input signals.
Setting details
Source : Play the picture and sound of the input source.
BD / DVD / TV / SAT/CBL / GAME / V.AUX / DOCK : Select video input
source to view. This can be set for individual input sources.
“BD”, “TV” and “GAME” can be selected only when a component
video connector is assigned as an input source.
NOTE
•It is not possible to select HDMI input signals.
•Input sources for which “Delete” is selected at “Source Delete”
(vpage 53) cannot be selected.
BD
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
DVD
SAT/CBL
GAME
42
Setting details
Input Mode
Set the audio input modes
for the different input
sources.
Set the source video.
z“BD”,
z
“TV” or “GAME” can be set when “HDMI” (vpage 41) or “Component” (vpage 42) has been
assigned.
Setting items
•If “Video Mode” is set to “Auto”, the mode is switched according to the
input contents.
•If a source is played in both MAIN ZONE (audio and video) and ZONE2
(audio only) modes in the same room, audio in MAIN ZONE and ZONE2
modes may sound out of synchronization, but this is not malfunction.
In this case, setting to “Game” mode may improve audio synchronization.
Default settings are underlined.
Default settings are underlined.
Video Select
Video of another input
source is played back
combined with the playing
audio.
Auto : Process video automatically based on the HDMI content
information.
Movie : Process video normally.
Game : Always process video appropriate for game content.
TV
DOCK
V.AUX
Confirm the setting
•This item can be set for input sources for which “HDMI” or “Digital” is
assigned at “Input Assign” (vpage 41).
•Normally set this mode to “Auto”. Set “PCM” and “DTS” when
inputting the corresponding input signal.
Return to previous menu
ENGLISH
Input Setup
Change the display name of the selected input source.
Setting items
•Up to eight characters can be input.
•For character input, see page 38.
Menu operation
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Source Level
The “MAIN” indicator lights.
Default settings are underlined.
•This function corrects the playback level of the selected input source’s audio input.
•Make this setting if there are differences in the input volume levels between the different sources.
Setting details
–12dB – +12dB (0dB)
Playback Mode
•To return to the previous item, press RETURN.
•Exiting the Menu, press MENU while the menu is displayed.
The menu display disappears.
Items that can be set with the Audio Adjust procedure
This item can be set when the input source is “DOCK”.
Setting items
The menu is displayed on the TV screen.
Advanced version
The analog input level and digital input level can be adjusted independently for input sources for
which “HDMI” or “Digital” is assigned at “Input Assign“ (vpage 41).
Repeat
Make settings for repeat
mode.
Shuffle
Make settings for shuffle
mode.
1 Press ZONE SELECT to switch the zone mode to “MAIN”.
AMP to set the remote control unit to amplifier operation
2 Press
mode.
3 Press MENU.
4 Press ui to select the menu to be set or operated.
5 Press ENTER to enter the setting.
Basic version
Rename
Change the display name of
the selected input source.
Default
The input source name
is returned to the default
setting.
Setting details
Audio Adjust
The sound being played in the surround mode can be adjusted to your liking.
The items (parameters) that can be adjusted depend on the signal being input and the currently
set surround mode. For details on the adjustable parameters, see “Surround modes and surround
parameters” (vpage 65).
Setting details
All : All files are played repeatedly.
One : A file being played is played repeatedly.
OFF : Repeat playback mode is canceled.
nn When DENON control dock for iPod ASD-1R or ASD-11R is
connected
Songs : All files are played in shuffle playback mode.
Albums : Files in the album are played in shuffle playback mode.
OFF : Shuffle playback mode is canceled.
Surround Parameter (vpage 44)
Tone (vpage 45)
Audyssey Settings (vpage 46)
Manual EQ (vpage 47)
RESTORER (vpage 48)
Information
nn When DENON control dock for iPod ASD-3N, ASD-3W, ASD-51N
or ASD-51W is connected
ON : Shuffle playback mode is enabled.
OFF : Shuffle playback mode is canceled.
Audio Delay (vpage 48)
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Simple version
Rename
Confirm the setting
Return to previous menu
43
ENGLISH
Audio Adjust
Surround Parameter
Default settings are underlined.
Adjust surround sound parameters. It may not be possible to set this item depending on the input signal.
Setting items
Mode
Set the play modes for the
different surround modes.
Setting details
nn In the PLgx or PLg mode
Cinema : Surround sound mode optimized for movie sources.
Music : Surround sound mode optimized for music sources.
Game : Surround sound mode optimized for games.
Pro Logic : Dolby Pro Logic playback mode (PLg mode only).
nn In the PLgz mode
Height : Dolby PLgz Height playback mode.
nn In the DTS NEO:6 mode
Cinema : Surround sound mode optimized for movie sources.
Music : Surround sound mode optimized for music sources.
Cinema EQ
Soften the treble range
of movie soundtracks for
better understanding.
DRC
Compress dynamic range
(difference between loud
and soft sounds).
D.Comp
Compress dynamic range
(difference between loud
and soft sounds).
LFE
Adjust the low-frequency
effects level (LFE).
Center Image
Assign center channel
signal to front left and right
channels for wider sound.
44
•When “Surround Parameter” – “Front Height” (vpage 45) is set to
“ON”, the “Height” mode is set automatically.
•The “Music” mode is also effective for movie sources including a lot of
stereo music.
ON : “Cinema EQ” is used.
OFF : “Cinema EQ” is not used.
Auto : Automatic dynamic range compression on/off control according to
the source. This can be set in the Dolby TrueHD mode.
Low / Mid / High : These set the compression level.
OFF : Dynamic range compression is always off.
Low / Mid / High : These set the compression level.
OFF : Turn dynamic range compression off.
–10dB – 0dB
For proper playback of the different sources, we recommend setting
to the values below.
•Dolby Digital sources : “0dB”
•DTS movie sources : “0dB”
•DTS music sources : “–10dB”
0.0 – 1.0 (0.3)
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Setting items
Panorama
Assign front L/R signal also
to surround channels for
wider sound.
Dimension
Shift sound image center
to front or rear to adjust
playback balance.
Center Width
Assign center channel
signal to front left and right
channels for wider sound.
Delay Time
Adjust delay time to control
sound stage size.
Effect Lev.
Adjust effect signal level.
Room Size
Determine size of acoustic
environment.
Setting details
ON : Set.
OFF : Do not set.
0 – 6 (3)
0 – 7 (3)
0ms – 300ms (30ms)
1 – 15 (10)
Set to a lower level if the positioning and sense of phase of the
surround signals seems unnatural.
Small : Simulate acoustics of a small room.
Medium-S : Simulate acoustics of a medium-small room.
Medium : Simulate acoustics of a medium room.
Medium-L : Simulate acoustics of a medium-large room.
Large : Simulate acoustics of a large room.
NOTE
AFDM
(Auto flag detect mode)
Detect the source’s
surround back channel
signal and set the
optimum surround mode
automatically.
“Room Size” does not indicate the size of the room in which sources are
played.
ON : Set.
OFF : Do not set.
[Example] Playing Dolby Digital software (with EX flag)
•When “AFDM” is set to “ON”, the surround mode is automatically set
to the DOLBY D + PLgx C mode.
• To play in the DOLBY DIGITAL EX mode, set “AFDM” to “OFF” and
“Surround Parameter” – “S.Back” to “MTRX ON”.
Some Dolby Digital EX sources do not include EX flags. If the playback
mode does not switch automatically even when “AFDM” is set to
“ON”, set “Surround Parameter” – “S.Back” to “MTRX ON” or
“PLgx CINEMA”.
Confirm the setting
Return to previous menu
ENGLISH
Audio Adjust
S.Back
Sets the method of
generating of the surround
back channel.
Setting details
nn For 2-channel sources
ON : The surround back channel is used.
OFF : No signal is played from the surround back channels.
Setting items
Height Gain
Control the front height
channel volume.
Default
The “Surround Parameter”
settings are returned to the
default settings.
Tone
Default settings are underlined.
Adjust the tonal quality of the sound.
Setting items
NOTE
“Tone Control” can be set when “Dynamic EQ” (vpage 46) is set to
“OFF”.
Move the cursor
(Up/Down/Left/Right)
NOTE
•“Tone Control” settings are not reflected to ZONE2.
•The tone cannot be adjusted in the direct mode.
–6dB – +6dB (0dB)
Bass
Adjust low frequency range
“Bass” can be set when “Tone Control” is set to “ON”.
(bass).
Treble
–6dB – +6dB (0dB)
Adjust high frequency range
“Treble” can be set when “Tone Control” is set to “ON”.
(treble).
Confirm the setting
Return to previous menu
Information
•“Front Height” is displayed with the settings listed below.
•When “Amp Assign” (vpage 49) is set to “Front Height”.
•When the “Speaker Config.” – “Front Height” setting (vpage 49) is
set to other than “None”.
•“Front Height” cannot be set if the HD Audio source being played
includes a front height channel. In this case, the Front height channel
is played back without decoding in PLgz mode, using the input signal.
Setting details
Tone Control
ON : Allow tone adjustment (bass, treble).
Set the tone control function OFF : Playback without tone adjustment.
to ON and OFF.
NOTE
If the setting in “Speaker Config.” – “S.Back” (vpage 49) is “None”,
“S.Back” is not displayed.
ON : Audio is output from the front height speaker.
OFF : Audio is not output from the front height speaker.
NOTE
This can be set when the surround mode is “DIRECT” (vpage 65, 66), and
the “Subwoofer Mode” (vpage 50) is “LFE+Main”.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Advanced version
•This can also be set by pressing STANDARD.
•If the source being played contains a surround
back signal, the decoder type is automatically
selected by the AFDM function. Set “AFDM” to
“OFF” to switch to your preferred decoder.
Subwoofer
Turn subwoofer output on
and off.
“Height Gain” is displayed for the following settings.
•When “Amp Assign” (vpage 49) is set to “Front Height”.
•When the “Speaker Config.” – “Front Height” setting (vpage 49) is set
to other than “None”.
•When surround mode is “PLgz” or the PLgz decoder is used.
ON : The subwoofer is used.
OFF : The subwoofer is not used.
Basic version
z1 This can be selected when playing DTS sources.
z2 This can be selected when playing DTS sources including a signal to
identify discrete 6.1-channel signals.
z3 This can be selected when “Speaker Config.” – “S.Back” (vpage 49)
is set to “2sp”.
Remote control operation
buttons
Low : Reduce the front height channel volume.
Mid : Front height channel sound is output with standard sound volume.
High : Increase the front height channel volume.
NOTE
nn For Multi-channel sources
Set the decoding method for the surround back channel.
DSCRT ON : Play the surround back signals included in the 7.1-channel
source.
MTRX ON : Generate and play the surround back signals from the
surround channel signals.
ES MTRXz1 : Generate and play the surround back signals from the
surround channel signals of the DTS source.
ES DSCRTz2 : Play the surround back signals included in the
6.1-channel DTS source.
PLgx CINEMAz3 : Generate and play the surround back signals by
decoding the signals in the Dolby Pro Logic gx Cinema mode.
PLgx MUSIC : Generate and play the surround back signals by
decoding the signals in the Dolby Pro Logic gx Music mode.
OFF : Do not play the surround back channel.
Front Height
Determine whether to use
front height channel.
Setting details
Simple version
Setting items
45
ENGLISH
Audio Adjust
Audyssey Settings
Default settings are underlined.
Set MultEQ®, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto Setup
has been performed. For additional information on Audyssey technology, please see page 69.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 10) to return to
the settings after Audyssey Auto Setup was run.
Setting items
MultEQ
Select one equalizer from
three modes. MultEQ
corrects both time and
frequency response
problems in the listening
area based on Audyssey
Auto Setup calibration. We
recommend “Audyssey”.
MultEQ is the prerequisite
function for Dynamic EQ
and Dynamic Volume.
Setting details
•“Audyssey”, “Audyssey Byp. L/R” and
“Audyssey Flat” can be selected after Audyssey
Auto Setup has been performed. “Audyssey” is
automatically selected after performing Audyssey
Auto Setup. When “Audyssey”, “Audyssey Byp.
L/R” or “Audyssey Flat” is selected,
illuminates.
•After running Audyssey Auto Setup, if the
Speaker Configuration, Distance, Channel
Level, and Crossover Frequency have changed
without increasing the number of speakers
illuminates.
measured, only
•Pressing MULTEQ on the remote control unit
or the main unit makes this setting.
•“MultEQ” and “Manual” cannot be selected when “EQ Customize” is
set to “Not Used” (vpage 52).
•When using headphones, “MultEQ” is automatically set to “OFF”.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Setting details
ON : Use Dynamic EQ.
OFF : Do not use Dynamic EQ.
•
is displayed when set to “ON”.
•Buttons on the remote control unit or main unit
can be used for operations.
GOperations with the remote control unitH
Press DYN EQ/VOL.
Each time DYN EQ/VOL is pressed, the setting is changed as shown
below.
Dynamic EQ : ON /
Dynamic EQ : ON /
Dynamic Volume : Midnight
Dynamic Volume : Evening
Audyssey : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Manual : Apply frequency response set with “Manual EQ” (vpage 47).
OFF : Turn “MultEQ” equalizer off.
NOTE
46
Setting items
Dynamic EQ®
Solve the problem of
deteriorating sound quality
as volume is decreased by
taking into account human
perception and room
acoustics.
Dynamic EQ : OFF /
Dynamic EQ : ON /
Dynamic Volume : OFF
Dynamic Volume : OFF
GOperations with the main unitH
Press DYNAMIC EQ.
Each time DYNAMIC EQ is pressed,
the setting is changed as shown
below.
Dynamic EQ : ON
Dynamic EQ : OFF
Reference Level Offset
Audyssey Dynamic EQ is
referenced to the standard
film mix level. It makes
adjustments to maintain
the reference response
and surround envelopment
when the volume is turned
down from 0 dB. However,
film reference level is not
always used in music or
other non-film content.
Dynamic EQ Reference
Level Offset provides three
offsets from the film level
reference (5 dB, 10 dB, and
15 dB) that can be selected
when the mix level of the
content is not within the
standard.
Confirm the setting
Dynamic EQ : ON /
Dynamic Volume : Day
0dB (Film Ref) : This is the default setting and should be used when
listening to movies.
5dB : Select this setting for content that has a very wide dynamic range,
such as classical music.
10dB : Select this setting for jazz or other music that has a wider dynamic
range. This setting should also be selected for TV content as that is usually
mixed at 10 dB below film reference.
15dB : Select this setting for pop/rock music or other program material
that is mixed at very high listening levels and has a compressed dynamic
range.
Setting is enabled when “Dynamic EQ” is “ON” (vpage 46).
Return to previous menu
ENGLISH
Audio Adjust
Setting details
Midnight : Most adjustment to softest and loudest sounds.
Evening : Medium adjustment to loudest and softest sound.
Day : Least adjustment to loudest and softest sounds.
OFF : Do not use the “Dynamic Volume”.
•
is displayed when set to “ON”.
Dynamic EQ : ON /
Dynamic Volume : Midnight
Dynamic EQ : OFF /
Dynamic Volume : OFF
Dynamic EQ : ON /
Dynamic Volume : Evening
Dynamic EQ : ON /
Dynamic Volume : OFF
Dynamic EQ : ON /
Dynamic Volume : Day
Dynamic Volume : OFF
Dynamic Volume : Midnight
Dynamic Volume : Day
Dynamic Volume : Evening
Use the graphic equalizer to adjust the tone of each speaker.
“Manual EQ” can be set when “MultEQ®” setting (vpage 46) is “Manual”.
Setting items
Setting details
Adjust CH
Correct the tone of each
speaker.
q Select the speaker tone adjustment method.
All CH : Adjust the tone of all speakers together.
L/R CH : Adjust the tone of left and right speakers together.
Each CH : Adjust the tone of each speaker.
w Select the speaker.
e Select the adjustment frequency band.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz / 16kHz
•Select the speakers you want to adjust when “L/R” or “Each” is
selected.
r Adjust the level.
–20.0dB – +6.0dB (0.0dB)
Base Curve Copy
Yes : Copy.
Copy “Audyssey Flat” curve No : Do not copy.
from MultEQ.
“Base Curve Copy” is displayed after Audyssey Auto Setup has been
performed.
Default
Yes : Reset to the defaults.
The “Manual EQ” settings
No : Do not reset to the defaults.
are returned to the default
settings.
Advanced version
GOperations with the main unitH
Press DYNAMIC VOLUME.
Each time DYNAMIC VOLUME is
pressed, the setting is changed as
shown below.
Default settings are underlined.
Basic version
•If “Dynamic Volume” is set to “Yes” in Auto Setup (vpage 9), the
setting is automatically changed to “Evening”.
•Buttons on the remote control unit or main unit
can be used for operations.
GOperations with the remote control unitH
Press DYN EQ/VOL.
Each time DYN EQ/VOL is pressed, the setting is
changed as shown below.
Manual EQ
Simple version
Setting items
Dynamic Volume®
Solve the problem of large
variations in volume level
between TV, movies and
other content (between
quiet passages and
loud passages, etc.) by
automatically adjusting to
the user’s preferred volume
setting.
Information
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
47
ENGLISH
Audio Adjust
Manual Setup
RESTORER
Compressed audio formats such as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the
amount of data by eliminating signal components that are hard for the human ear to hear. The RESTORER
function generates the signals eliminated upon compression, restoring the sound to conditions near those
of the original sound before compression. It also corrects the sense of volume of the bass to obtain richer
sound with compressed audio signals.
Setting details
OFF : Do not use RESTORER.
Mode 1 (RESTORER 64) : Optimized mode for compressed sources with very weak highs.
Mode 2 (RESTORER 96) : Apply suitable bass and treble boost for all compressed sources.
Mode 3 (RESTORER HQ) : Optimized mode for compressed sources with normal highs.
•This item can be set with analog signals or when a PCM signal (fs = 44.1/48
kHz) is input.
•This cannot be set when the surround mode is set to “DIRECT”.
•This item default setting for “iPod” is “Mode 3”. All others are set to “OFF”.
•When set to something other than “OFF”,
is displayed.
•Pressing RESTORER on the remote control unit or the main unit makes this
setting.
OFF
Mode 1
(RESTORER 64)
Mode 2
(RESTORER 96)
Set when changing Audyssey® Auto Setup settings, or when changing the audio, video, display
or other settings.
•If you change the speaker settings after performing Audyssey Auto Setup, it will not be possible
to set MultEQ®, Dynamic EQ® and Dynamic Volume® (vpage 46, 47).
•Can be used without changing the settings. Please set if necessary.
Menu operation
1 Press ZONE SELECT to switch the zone mode to “MAIN”.
AMP to set the remote control unit to amplifier operation
2 Press
mode.
3 Press MENU.
4 Press ui to select the menu to be set or operated.
5 Press ENTER to enter the setting.
The “MAIN” indicator lights.
The menu is displayed on the TV screen.
•To return to the previous item, press RETURN.
•Exiting the Menu, press MENU while the menu is displayed.
The menu display disappears.
Mode 3
(RESTORER HQ)
Items that can be set with the Manual Setup procedure
Audio Delay
Default settings are underlined.
While viewing video, manually adjust the time to delay audio output.
Setting details
0ms – 200ms
•This item can be set within the range of 0 to 100 ms when “Auto Lip Sync” is set to “ON” and when
a TV compatible with Auto Lip Sync is connected.
•Store “Audio Delay” for each input source.
•Audio Delay for game mode can be set when “Video Mode” (vpage 42) is set to “Game”.
Speaker Setup (vpage 49)
HDMI Setup (vpage 51)
4-2.HDMI Setup
4-3.Audio Setup
1.Amp Assign
2.Speaker Config.
3.Bass Setting
4.Distance
5.Channel Level
6.Crossover Freq.
Auto Lipsync
: ON
HDMI Audio Out : Amp
HDMI Control
: OFF
1.2ch Direct/Stereo
2.Auto Surround Mode
3.EQ Customize
[RTN]:Back
[ENT]:Select [RTN]:Back
ZONE2 Setup (vpage 53)
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
[ENT]:Select [RTN]:Back
Option Setup (vpage 53)
4-4.ZONE2 Setup
4-5.Option Setup
Level Lch
:
0dB
Level Rch
:
0dB
Vol.limit
: OFF
Power On Lev: Last
Mute Lev.
: Full
1.Volume Control
2.Source Delete
3.On-Screen Display
4.Remote Preset Codes
5.Quick Select Name
6.ZONE Rename
7.Display
[RTN]:Back
48
Audio Setup (vpage 52)
4-1.Speaker Setup
Confirm the setting
[ENT]:Select [RTN]:Back
Return to previous menu
ENGLISH
Manual Setup
Default settings are underlined.
Perform when setting the speakers manually or when changing settings made in Audyssey Auto Setup.
•If you change the speaker settings after performing Audyssey Auto Setup, it will not be possible to select
MultEQ, Dynamic EQ and Dynamic Volume (vpage 46, 47).
•Manual Setup can be used without changing the settings. Please set if necessary.
Setting items
Speaker Config.
(Continued)
Setting details
Surround : Set the presence and size of the surround speakers.
•Large : Use a large speaker that can adequately play back low
frequencies.
•Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
•None : Select when the surround speakers are not connected.
•When “Surround” is set to “Large”, “Surround Back” and “Front
Height” can be set to “Large”.
•When “Surround” is set to “None”, “Surround Back” and “Front
Height” can automatically set to “None”.
S.Back : Set the presence, size and number of surround back speakers.
•Large : Use a large speaker that can adequately play back low
frequencies.
•Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
•None : Select when the surround back speakers are not connected.
Since “Amp Assign” of this unit is set to “ZONE2” by default, audio is
not output from the surround back speakers. When using the surround
back speakers with MAIN ZONE, change the “Amp Assign” setting to
“Normal”.
Speaker Config.
Front : Set the front speaker size.
Select speaker configuration •Large : Use a large speaker that can adequately play back low
and size (bass reproduction
frequencies.
capability).
•Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
Even when the “S.Back“ setting is other than “None”, sound may
not be emitted from the surround back speaker, depending on the
playback source. In this case, make “Surround Parameter” – “S.Back”
setting other than “OFF” (vpage 45).
•2sp : Use two surround back speakers.
•1sp : Use only one surround back speaker. When you select this setting,
connect the surround back speaker to the left (L) channel.
NOTE
When the “Amp Assign” setting (vpage 49) is other than “Normal”, you
cannot make the “S.Back” setting.
Front Height : Set the presence and size of the front height speakers.
•Large : Use a large speaker that can adequately play back low
frequencies.
•Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
•None : Select when the front height speakers are not connected.
NOTE
Do not use the outward
shape of the speaker to
determine selection of a
“Large” or “Small” speaker.
Instead, use the frequencies
set in “Crossover
Frequency” (vpage 50) as
the standard for determining
bass reproduction capability.
•When “Subwoofer” is set to “No”, “Front” is automatically set to
“Large”.
•When “Front” is set to “Small”, “Center”, “Surround“, “Surround
Back” and “Front Height” can not be set to “Large”.
Center : Set the presence and size of the center speaker.
•Large : Use a large speaker that can adequately play back low
frequencies.
•Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
•None : Select when a center speaker is not connected.
NOTE
When “Front” is set to “Small”, “Subwoofer” is automatically set to
“Yes”.
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
49
Information
When the “Amp Assign” setting (vpage 49) is other than “Front Height”,
you cannot make the “Front Height” setting.
“Large” is not displayed when “Front” is set to “Small”.
Subwoofer : Set the presence of a subwoofer.
•Yes : Use a subwoofer.
•No : Select when a subwoofer is not connected.
Remote control operation
buttons
Advanced version
Setting details
Normal : Set when using 7.1-channel (Front/Center/Surround/Surround
Back/Subwoofer) speakers.
ZONE2 : Set for connecting the speakers for ZONE2 to the SURR. BACK/
AMP ASSIGN terminals.
Front Height : Set for connecting the front height speakers to the SURR.
BACK/AMP ASSIGN terminals.
Front Bi-Amp : Set for connecting a tweeter of a front speaker to the
SURR. BACK/AMP ASSIGN terminals and a woofer of the front speaker to
the FRONT terminals.
Front B : Set for connecting the second front speakers to the SURR.
BACK/AMP ASSIGN terminals. In this case, make settings for “Front
Speaker Setup” (vpage 51).
Basic version
Setting items
Amp Assign
Set the speakers connected
to this unit.
Simple version
Speaker Setup
ENGLISH
Manual Setup
Setting items
Bass Setting
Set subwoofer and LFE
signal range playback.
Setting details
Channel Level
Test Tone Start : Output test tone.
Set the volume of the test
•FL / C / FR / SR / SBRz / SBLz / SL / FHL / FHR / SW : Select the
tone to be the same when it
speaker.
is output from each speaker. zWhen
z
the “Speaker Config.” – “S.Back” setting (vpage 49) is set to
“1sp”, “S.Back” is displayed.
•“Subwoofer Mode” can be set when “Speaker Config.” – “Subwoofer”
(vpage 49) is set to “Yes”.
•Play music or a movie source and select the mode offering the strongest
bass.
•Select “LFE+Main” if you want the bass signals to always be produced
from the subwoofer.
•When o is pressed while the subwoofer volume is set to “–12 dB”, the
“Subwoofer” setting switches to “OFF”.
•When “Channel Level” is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 33.
If “Front” and “Center” for “Speaker Config.” are set to “Large”, and
“Subwoofer Mode” is set to “LFE”, no sound may be output from the
subwoofers, depending on the input signal or selected surround mode.
LPF for LFE : Set LFE signal playback range.
•80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Unit : Set the unit of distance.
•Feet / Meters
Step : Set the minimum variable width of the distance.
•1ft / 0.1ft
•0.1m / 0.01m
FL / FR / C / SW / SL / SR / SBLz / SBRz / FHL / FHR : Select the speaker.
zWhen
z
the “Speaker Config.” – “S.Back” setting (vpage 49) is set to
“1sp”, “S.Back” is displayed.
•The speakers that can be selected differ depending on the “Amp Assign”
(vpage 49) and “Speaker Config.” (vpage 49) settings.
•Default settings :
FL / FR / C / SW / FHL / FHR : 12.0 ft (3.6 m)
SL / SR / SBL / SBR : 10.0 ft (3.0 m)
•Set the difference in the distance between the speakers to less than 20
ft (6.0 m).
NOTE
Speakers set to “None” in “Speaker Config.” (vpage 49) are not displayed.
Default : The “Distance” settings are returned to the default settings.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
When you select “Default” and press ENTER, the “Default Setting?”
prompt is displayed. Select either “Yes” or “No”, and press ENTER.
Remote control operation
buttons
•–12.0dB – +12.0dB (0.0dB) : Adjust the volume.
NOTE
•0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.
50
Setting details
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
•LFE : The low range signal of the channel set to “Small” speaker size is
added to the LFE signal output from the subwoofer.
•LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
NOTE
Distance
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
Setting items
Move the cursor
(Up/Down/Left/Right)
•Speakers set to “None” in the “Speaker Config.” (vpage 49) settings
are not displayed.
•When a headphones jack is inserted in the PHONES jack of this unit, the
“Channel Level” is not displayed.
Default : The “Channel Level” settings are returned to the default settings.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
Crossover : Set the crossover frequency.
Crossover Frequency
Set the maximum frequency •40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
of the bass signal output
from each channel to
Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
•Front / Center / Surround / S.Back / Front Height : Select the speaker.
Crossover Frequency to
•40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
suit the bass reproduction
250Hz : Set the crossover frequency.
capability of the speaker
being used.
•“Crossover Frequency” can be set when the “Bass Setting” –
“Subwoofer Mode” (vpage 50) setting is “LFE+Main”, or when you
have a speaker that is set to “Small”.
•Always set the crossover frequency to “80Hz”. When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
•For speakers set to “Small”, sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
•The speakers that can be set when “Advanced” is selected differ
depending on the “Subwoofer Mode” setting (vpage 50).
•When “LFE” is selected, speakers set to “Small” at “Speaker Config.”
can be set. If the speakers are set to “Large”, “Full Band” is displayed
and the setting cannot be made.
•If set to “LFE+Main”, this setting can be made regardless of the
speaker size.
Confirm the setting
Return to previous menu
ENGLISH
Manual Setup
Front Speaker Setup
Set the front speakers to
use for every surround
mode.
NOTE
DIRECT/STEREO : The front speakers used in the direct, stereo and pure
direct play modes (2 channel) are set in advance.
•A:Front speaker A is used.
•B:Front speaker B is used.
•A+B:Both front speakers A and B are used.
MULTI CH : The front speakers used in modes other than the direct,
stereo and pure direct play modes (2 channel) are set in advance.
•A:Front speaker A is used.
•B:Front speaker B is used.
•A+B:Both front speakers A and B are used.
HDMI Setup
Default settings are underlined.
Make settings for HDMI video/audio output.
Setting items
Auto Lip Sync
Make automatic
compensation for timing
shift in audio and video
output.
HDMI Audio Out
Select HDMI audio output
device.
Setting details
ON : Compensated.
OFF : Not compensated.
Amp : Play back through speakers connected to the receiver.
TV : Play back through TV connected to the receiver.
NOTE
Standby Source
Sets the HDMI input source
to put into standby when
the power is on.
“Standby Source” can be set when “HDMI Control” is set to “ON”.
All : If power to a connected TV is turned off independently of the input
source, power to this unit is automatically set to standby.
Video : If power to a connected TV is turned off when the input source
is BD / DVD / TV / SAT/CBL / GAME / V.AUX / DOCK, power to this unit is
automatically set to standby.
OFF : This unit does not link with power to a TV.
“Power Off Control” can be set when “HDMI Control” is set to “ON”.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
51
Information
Power Off Control
Links the power standby
of this unit to external
equipment.
•When “HDMI Control” is set to “ON”, it consumes more standby
power. If you are not using this unit for an extended period, it is
recommended that you unplug the power cord from the power outlet.
•“HDMI Control” does not work when the power to the equipment is off.
Either turn power on or set to standby.
•The HDMI control function controls operations of a TV that is compatible
with the HDMI control function. Make sure that the TV and HDMI are
connected when you perform HDMI control.
•If the “HDMI Control” settings have been changed, always reset the
power to connected devices after the change.
Last : This item is set at the last-used input source.
HDMI1 / HDMI2 / HDMI3 / HDMI4 : Put the respective input source into
standby.
Advanced version
When the HDMI control function is activated, priority is given to the TV
audio setting (vpage 32 “HDMI control function”).
ON : Use HDMI control function.
HDMI Control
You can link operations with OFF : Do not use HDMI control function.
devices connected to HDMI
and compatible with HDMI
•When a device that is not compatible with the HDMI control function is
Control.
connected, set “HDMI Control” to “OFF”.
•Please consult the operating instructions for each connected component
to check the settings.
•Refer to “HDMI control function” (vpage 32) for more information about
the HDMI control function.
Basic version
This can be set when “Amp
Assign” is set to “Front B”
(vpage 49).
Setting details
Simple version
Setting items
ENGLISH
Manual Setup
Audio Setup
Default settings are underlined.
2ch DIRECT/STEREO
(Continued)
Make settings for audio playback.
Setting items
2ch DIRECT/STEREO
Select the method for
setting the speakers used
in the 2-channel direct and
stereo playback modes.
Setting details
Setting : Select the method for setting the speakers used in the 2-channel
direct and stereo playback modes.
•Basic : The settings at “Speaker Setup” (vpage 49) are applied.
•Custom : Make separate settings for 2-channel. Make the following
settings:
Front : Set the front speaker size.
•Large : Use a large speaker that can adequately play back low
frequencies.
•Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
If “Speaker Config.” – “Subwoofer” (vpage 49) is set to “No”, the
setting is automatically set to “Large”.
Subwoofer : Set the presence of a subwoofer.
•Yes : Use a subwoofer.
•No : Select when a subwoofer is not connected.
If “Speaker Config.” – “Subwoofer” (vpage 49) is set to “No”, the
setting is automatically set to “No”. If the “Front” setting is “Small”,
the setting is automatically “Yes”.
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
•LFE : When the “2ch DIRECT/STEREO” – “Front” setting is set to
“Large”, the LFE signal alone is output from the subwoofer. Also, when
the “2ch DIRECT/STEREO” – “Front” setting is set to “Small”, the front
channel low range signal is added to the LFE signal output from the
subwoofer.
•LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This setting can be set made “2ch DIRECT/STEREO” – “Subwoofer”
is set to “Yes”.
Crossover : Set the maximum frequency of the bass signal output from
each channel to the subwoofer.
•40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
•This setting can be set made “2ch DIRECT/STEREO” – “Subwoofer” is
set to “Yes”.
•If the “2ch DIRECT/STEREO” – “Front” setting is “Large” and the
“Subwoofer Mode” setting is “LFE”, “Full Band” is displayed and the
setting cannot be made.
52
Setting items
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Auto Surround Mode
Make setting for
memorizing surround mode
setting for each input signal
type.
Setting details
Distance FL / Distance FR : Select the speaker.
•0.0ft – 60.0ft (12.0ft) / 0.00m – 18.00m (3.60m) : Set the distance to
the speaker.
Set so that the difference between the front left speaker and front
right speaker distances is 6.0 m (20.0 ft) or less.
Level FL / Level FR : Select the speaker.
•–12.0dB – +12.0dB (0.0dB) : Adjust the level of each channel.
ON : Memorize settings. Automatically play with the last used surround
mode.
OFF : Do not memorize settings. Surround mode does not change
according to input signal.
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals
listed below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r LPCM Multi-channel signals
Audyssey Byp. L/R : Set when not using “Audyssey Byp. L/R” equalizer.
EQ Customize
Set so that unused equalizer •Used : Use.
•Not Used : Do not use.
settings are not displayed
when MULTEQ is pressed.
Set so that “Audyssey Byp. L/R” settings can be made when
Audyssey Auto Setup is performed.
Audyssey Flat : Set when not using “Audyssey Flat” equalizer.
•Used : Use.
•Not Used : Do not use.
Set so that “Audyssey Flat” settings can be made when Audyssey
Auto Setup is performed.
Manual : Set when not using the “Manual” equalizer.
•Used : Use.
•Not Used : Do not use.
The equalizer mode in which
“Not Used” is selected
cannot be stored and
recalled in the Quick Select
function.
Confirm the setting
Return to previous menu
ENGLISH
Manual Setup
Default settings are underlined.
Set the audio to play back with ZONE2.
“ZONE2 Setup” is displayed when “ZONE2” is selected with “Amp Assign”.
Setting items
Power On Level
Define the volume setting
that is active when the
power is turned on.
Make various other settings.
Setting items
Volume Control
Set the MAIN ZONE (room
where the unit is located)
volume setting.
–12dB – +12dB (0dB)
OFF : Do not set a maximum volume.
–20dB (61) / –10dB (71) / 0dB (81)
This is displayed from 0 – 99 when “Volume Display” (vpage 53) is
set to “Absolute”.
Last : Use the memorized setting from the last session.
– – – (0) : Always mute when power is turned on.
–80dB – 18dB (1 – 99) : The volume is adjusted to the set level.
This is displayed from 0 – 99 when “Volume Display” (vpage 53) is
set to “Absolute”.
Full : The sound is muted entirely.
–40dB : The sound is attenuated by 40 dB down.
–20dB : The sound is attenuated by 20 dB down.
Source Delete
Remove from the display
input sources that are not
used.
Setting details
Volume Display : Set how volume is displayed.
•Relative : Display ---dB (Min), in the range –80.5 dB – 18 dB.
•Absolute : Display in the range 0 (Min) – 99.
•The “Volume Display” setting is applied also to the “Volume Limit” and
“Power On Level” display method.
•The “Volume Display” setting applies to all zones.
Volume Limit : Make a setting for maximum volume.
•OFF : Do not set a maximum volume.
•–20dB (61) / –10dB (71) / 0dB (81)
Power On Level : Define the volume setting that is active when the
power is turned on.
•Last : Use the memorized setting from the last session.
•– – – (0) : Always use the muting on condition when power is turned on.
•–80dB – 18dB (1 – 99) : The volume is adjusted to the set level.
Mute Level : Set the amount of attenuation when muting is on.
•Full : The sound is muted entirely.
•–40dB : The sound is attenuated by 40 dB down.
•–20dB : The sound is attenuated by 20 dB down.
BD / DVD / TV / SAT/CBL / V.AUX / GAME / DOCK / TUNER : Select
input source that is not used.
•ON : Use this source.
•Delete : Do not use this source.
Advanced version
Mute Level
Set the amount of
attenuation when muting
is on.
–12dB – +12dB (0dB)
Default settings are underlined.
Basic version
Level Lch
Adjust the left channel
output level.
Level Rch
Adjust the right channel
output level.
Volume Limit
Make a setting for
maximum volume.
Setting details
Option Setup
Simple version
ZONE2 Setup
NOTE
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
53
Information
•Input sources being used in the various zones cannot be deleted.
•Input sources set to “Delete” cannot be selected using SOURCE SELECT.
Screensaver : Make screensaver settings.
On-Screen Display
Make the settings related to •ON : The screen saver is activated during menu display, iPod or TUNER
screen display if no operation is performed for an approximately 3-minute
displays on the TV screen.
continuous period. When you press uio p, the screensaver is
cancelled and the screen before that screen saver started is displayed.
•OFF : Screensaver is not activated.
Text : Display the details of operation when switching surround mode,
input mode, etc.
•ON : Turn display on.
•OFF : Turn display off.
ENGLISH
Manual Setup
Setting items
On-Screen Display
(Continued)
Remote Preset Codes
Search a preset code to
register in the remote
control unit.
Quick Select Name
Change the “Quick Select”
display title to one you
prefer.
Setting details
Master Volume : Display the master volume during adjustment.
•Bottom : Display at the bottom.
•Top : Display at the top.
•OFF : Turn display off.
When the master volume display is hard to see when superimposed
on movie subtitles, set to “Top”.
iPod : Set the iPod screen display time when the input source is “DOCK”.
•Always : Show display continuously.
•30sec : Show display for 30 seconds after operation.
•10sec : Show display for 10 seconds after operation.
•OFF : Turn display off.
TUNER : Set the tuner screen display time when the input source is
“TUNER”.
•Always : Show display continuously.
•30sec : Show display for 30 seconds after operation.
•10sec : Show display for 10 seconds after operation.
•OFF : Turn display off.
See “Registering preset codes” (vpage 56).
Setting items
Zone Rename
•Up to 10 characters can be input.
Change the display title of
•For character input, see page 38.
each zone to one you prefer. Default : The changed display names are reset to the defaults.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
Bright : Normal display brightness.
Display
Dim : Reduced display brightness.
Adjust the display
Dark : Very low display brightness.
brightness of this unit.
OFF : Turns the display off.
Buttons on the main unit can be used for
operations.
Each time DIMMER is pressed, the
setting is changed as shown below.
Bright
OFF
Setup Lock
Protect settings from
inadvertent change.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Dim
Dark
ON : Turn protection on.
OFF : Turn protection off.
When canceling the setting, set “Setup Lock” to “OFF”.
NOTE
Rename Label : Select this to change the displayed name for “Quick
Select” shown on the screen, as desired.
•Up to 16 characters can be input.
•For character input, see page 38.
When “Setup Lock” is set to “ON”, the settings listed below can no
longer be changed. Also, “SETUP LOCKED!” is displayed if you attempt
to operate related settings.
· Menu operations
· Dynamic Volume®
· RESTORER
· Channel Level
· MultEQ®
· Dynamic EQ®
Template : The display name can be changed by selecting “Operation”
and “Device Name” from the previously set templates.
1.Use ui to select the name of the Quick Select setting you want to
change, then press ENTER.
2.Use ui to select “Template”, then press ENTER.
3.Use ui to select “Operation”, then press ENTER.
•Watch / Listen to / Play / For
4.Use uio p to select “Device Name”, then press ENTER.
•BD / DVD / TV / Cable TV / Satellite / DVR / VCR / iPod / V.AUX
/ LD / Movie (When “Operation” is selected to “Watch”.)
•CD / TUNER / iPod / MD / TAPE / Music (When “Operation” is
selected to “Listen to”.)
•PC / Game (When “Operation” is selected to “Play”.)
•Father / Mother / Son / Daughter / Brother / Sister / Grandfather /
Grandmother / Me (When “Operation” is selected to “For”.)
Default : The changed“Quick Select Name” is returned to the default
setting.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
54
Setting details
Confirm the setting
Return to previous menu
ENGLISH
Items
Status
Show information about
current settings.
NOTE
nn MAIN ZONE
This item shows information about settings for MAIN ZONE.
Select Source / Name / Surround Mode / Input Mode /
Decode Mode / Video Select / Video Mode / Content Type
etc.
This item shows information about settings for ZONE2.
Power / Select Source / Volume Level
Surround Mode : The currently set surround mode.
Signal : The input signal type.
fs : The input signal’s sampling frequency.
Format : The number of channels in the input signal (front, surround, LFE).
Offset : The dialogue normalization correction value.
Flag : This is displayed when inputting signals including a surround back
channel. “MATRIX” is displayed with Dolby Digital EX and DTS-ES Matrix
signals, “DISCRETE” with DTS-ES Discrete signals.
Setting details
Quick Select 1 / Quick Select 2 / Quick Select 3 / ZONE2 Quick Select
1 / ZONE2 Quick Select 2 / ZONE2 Quick Select 3
•Name / Input Source / Video Select / Volume Level / MultEQ® /
Dynamic EQ® / Dynamic Volume® / Analog/PCM / Digital 2ch /
Digital 5.1ch / Multi Ch
“ZONE2 Quick Select” is displayed when “Amp Assign” is set to
“ZONE2”.
nn ZONE2
“Status” for ZONE2 is displayed when “Amp Assign” is set to
“ZONE2”.
Audio Input Signal
Show information about
audio input signals.
Quick Select
Show information about
“Quick select function”
(vpage 34) settings.
Preset Channel
Show information about
preset channels.
A/B/C/D/E/F/G
A1 – A8 / B1 – B8 / C1 – C8 / D1 – D8 / E1 – E8 / F1 – F8 / G1 – G8
TUNER
Basic version
The information displayed
differs according to the
input source.
Items
Setting details
Simple version
Information
Show information about receiver settings, input signals, etc.
Advanced version
Dialogue normalization function
This function is automatically activated when
playing Dolby Digital sources.
It automatically corrects the standard signal
level for individual program sources.
The correction value can be checked using
STATUS.
The figure is the corrected
value. This cannot be
changed.
HDMI Information
Show information about
HDMI input/output signals
and monitor.
HDMI Signal Information
•Resolution / Color Space / Pixel Depth
Auto Surround Mode
Show information about
auto surround mode
settings.
Analog/PCM / Digital 2ch / Digital 5.1ch / Multi Ch
HDMI Monitor Information
•Interface / Suport Resolution
Information
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
55
ENGLISH
Operating the connected devices by remote control unit
Registering the supplied preset codes in the remote control unit
enables you to operate devices made by other manufacturers.
Operating AV equipment
Input
Devices controllable with the remote
source Input source
control unit
select
of this unit
(Operation mode)
buttons
Press ZONE SELECT to select a
1 zone
for operation.
–
The zone mode indicator corresponding
to the operating zone lights.
•The mode switches each time ZONE
SELECT is pressed.
MAIN
ZONE2
ZONE3
Select for the operations in
MAIN ZONE.
Select for the operations in
ZONE2.
Not used.
•If setting of “Specifying the zone used with
the remote control unit” (vpage 59) is “2”,
operations in MAIN ZONE and ZONE2 are
enabled.
2 Press the input source select button (vpage 19).
•The input source for the zone selected in step 1 is switched.
•The operation mode of the remote control unit is switched as
shown in the table.
z
BD
z
DVD
z
TV
z
SAT/CBL
z
GAME
z
Device registered on the BD button
When preset codes are registered in the included remote control unit,
it can then be used to operate any devices you have, such as DVD
players or TVs made by different manufacturers.
In this menu, you can search and display the preset codes that can be
preset in the included remote control unit.
Device registered on the DVD button
nnButtons used for operating the devices
This unit (amplifier operation)
Device registered on the TV button
Device registered on the SAT/CBL button
Device registered on the GAME button
V.AUX
Device registered on the V.AUX button
TUNER
Radio of this unit
DOCK
Control dock for iPod
DOCK
Control dock for iPod
zIf
z a preset code is registered for this button, the remote control
unit of this unit can control another devices.
NOTE
If the mode of the remote control unit is set to other than ampoperation mode, press AMP to switch the remote control unit to the
amp-operation mode to perform the following operations:
•For menu operation by pressing MENU
•For setting the channel level of the unit by pressing CH LEVEL
•For turning power in each zone on or off by pressing ZONE/DEVICE
ON or ZONE/DEVICE OFF.
3
Registering preset codes
Operate this unit or the device whose input source is
switched.
q ZONE/DEVICE ON, ZONE/DEVICE OFF
For switching power of each device on or off.
w uio p, ENTER, RETURN
For menu operation of each device.
e MENU, SETUP, TOP MENU
For displaying the menu of each device.
r 1, 2, 3, 6, 7, 8, 9
t Number button (0 – 9, +10)
y CH +, CH –
u TV POWER, TV INPUT
For operating a TV
This button is enabled in any mode.
For details on operation with the remote control unit, see pages 22
to 23, 58, and 59.
nnDefault settings for preset codes
The devices shown below are registered for each input source
button as default. Settings can be changed according to the
devices to be used.
Input source
select
buttons
•For details, refer to the operating instructions for each device.
For operations of iPod and TUNER, see the following pages.
•iPod (vpage 22)
•TUNER (vpage 23)
Category
Brand
Preset code
Blu-ray Disc player
DENON
32258
DVD player
DENON
32134
Television
z
SONY
10810
Satellite set top box
DirecTV
01377
Cable set top box
Motorola
01376
DVD player
DENON
32134
Control dock for iPod
DENON
42517
zIf
z a control dock for iPod is not to be used, the preset code for
another device can be set to DOCK.
NOTE
56
•The preset code cannot be registered to TUNER.
•Do not register the preset code to iPod.
This button also functions as the Play button for an iPod.
ENGLISH
Registering preset codes
The “MAIN” indicator lights.
Brand Search
Press AMP to set the remote
2 control
unit to amplifier operation
The menu is displayed on the TV screen.
“Remote Preset Codes” and then
press ENTER.
4-5.Option Setup
[ENT]:Select [RTN]:Back
•The first character is displayed as 1, A to Z. (Initials for the brand are
displayed for each category.)
For brand names that start with numbers, select “1”.
7
Pressing ui, select the brand name. Then press
ENTER.
Brand[1/1]
- DVD -
Daewoo
Dantax
Denon
Disney
DSE
Durabrand
[ENT]:Select [RTN]:Back
ui, select the category
5 Pressing
of device for preset registration.
Then press ENTER.
4-5-4.RC Preset Codes
Category Search
Blu-ray
CD
CD Recorder
CABLE
CABLE/PVR
DVD
[ENT]:Select [RTN]:Back
[ENT]:Select
[RTN]:Back
•When there are several pages of brand names, the pages can be
switched by pressing the remote control unit’s CH + or CH –.
NOTE
If the desired brand name is not listed, the supplied remote control
unit cannot control the device. Use the remote control unit supplied
with the device to be used.
8
The procedures for registering remote control codes
and remote control preset registration are displayed.
The zone mode indicator flashes twice.
11 Enter a five-digit code using 0 – 9.
Press the buttons with an interval less than 10 seconds.
Category :DVD
Brand
:DENON
Code[1/3]:30490
Setup Remote
1.Press [Source]button.
2.Press and Hold 3sec.
both[PowerON][DeviceON]
3.Input Code with [0-9]
4.Press any key to check
device[e.g.DeviceON]
[QUICK1]:OK [QUICK2]:NG
•When the code is registered.
The zone mode indicator flashes twice.
•When the code is not registered correctly
The mode indicator slowly flashes once. Perform from step 9
again.
•When an input number is not correct
Press POWER ON once then perform the operations from Step
9 again.
12 Operate the device being used to check the operation.
•If the device is operating, press QUICK SELECT 1.
Go to step 13.
•If the device is not operating, press QUICK SELECT 2.
Go to step 14.
Information
Category :DVD
Brand
:DENON
Code[1/3]:30490
Setup Remote
1.Press [Source]button.
2.Press and Hold 3sec.
both[PowerON][DeviceON]
3.Input Code with [0-9]
4.Press any key to check
device[e.g.DeviceON]
[QUICK1]:OK [QUICK2]:NG
Hold POWER ON and ZONE/DEVICE ON pressed
10 simultaneously
for more than 3 seconds.
Advanced version
1.Volume Control
2.Source Delete
3.On-Screen Display
4.Remote Preset Codes
5.Quick Select Name
6.Zone Rename
7.Display
V.AUX, GAME or TV).
•For TV, only the preset code for the categories “TV”, “TV/DVD”, or
“TV/VCR” can be registered.
•For “TV”, “TV/DVD”, or “TV/VCR” categories, only the preset
code for TV can be registered.
Basic version
1
A
B
C
D
E
mode.
3 Press MENU.
ui to select “Manual
4 Use
Setup” – “Option Setup” –
- DVD -
Simple version
the input source button on which the preset
ui, select the first character of the brand
Press ZONE SELECT to switch the zone mode to
1 “MAIN”.
6 Pressing
9 Press
code is to be registered (DVD, BD, SAT/CBL, DOCK,
name. Then press ENTER.
57
ENGLISH
Registering preset codes
13
The screen shown below is displayed, and registration
of the preset code is completed.
Operating components
The supplied remote control unit can control a component other than
this unit.
1
2 Operate the component.
Switch the input source
(vpage 19).
Remote Preset Codes
setup is finished.
Press [AMP]button.
And Press [Enter]button
to return MENU.
•For details, refer to the component’s
operating instructions.
[ENT]:OK
•The menu screen is retrieved. Press AMP then ENTER.
14 Either of the screens below is displayed.
q
Selected code is not
matched.
Please try other codes
w
Sorry. your remote is
not supported.
This function can not
be used for your device
Press [AMP]button.
And Press [Enter]button
to return MENU.
[ENT]:OK
•The screen is displayed for 3
seconds, then the next preset
registration screen is displayed
automatically.
GIf screen q is displayedH
The device may be operating with the preset code displayed next.
The preset registration screen is displayed. Repeat steps 9 to 12.
GIf screen w is displayedH
The device cannot be controlled with the remote control unit supplied
with this unit. Use the remote control unit supplied with the device
to be used. The menu screen is retrieved. Press AMP then ENTER.
Some manufacturers use more than one type of remote control code.
Preset codes to change the number and verify correct operation.
nnBlu-ray Disc player / HD-DVD player /
DVD player / DVD recorder operation
Operation buttons
ZONE/DEVICE ON
ZONE/DEVICE OFF
CH +, –
MENU
TOP MENU
uio p
ENTER
SETUP
RETURN
Function
Power onz
Power standbyz
Switch channels (up/down)
(Popup) Menu
Top menu
Cursor operation
Enter setting
Setup
Return
6 7
Manual search
(fast-reverse/fast-forward)
1
8 9
3
2
Playback
Auto search (cue)
Pause
Stop
0 – 9, +10
Select title, chapter or channel
selection
TV POWER
TV INPUT
TV power on/standby (Default : SONY)
Switch TV input (Default : SONY)
NOTE
Depending on the model and year of manufacture of your equipment,
some buttons may not operate.
zThis
z
may power some devices on/standby.
58
nnCD player / CD recorder operation
Operation buttons
ZONE/DEVICE ON
ZONE/DEVICE OFF
uio p
ENTER
Function
Power onz
Power standbyz
Cursor operation
Enter setting
6 7
Manual search
(fast-reverse/fast-forward)
1
8 9
3
2
0 – 9, +10
TV POWER
TV INPUT
Playback
Auto search (cue)
Pause
Stop
Track selection
TV power on/standby (Default : SONY)
Switch TV input (Default : SONY)
nnDigital video recorder (PVR) /
video cassette recorder (VCR) operation
Operation buttons
ZONE/DEVICE ON
ZONE/DEVICE OFF
CH +, –
MENU
uio p
ENTER
SETUP
RETURN
Function
Power onz
Power standbyz
Switch channels (up/down)
Menu
Cursor operation
Enter setting
Setup
Return
6 7
Manual search
(fast-reverse/fast-forward)
1
8 9
3
2
Playback
Auto search (cue)
Pause
Stop
0 – 9, +10
Select title, chapter or channel
selection
TV POWER
TV INPUT
TV power on/standby (Default : SONY)
Switch TV input (Default : SONY)
ENGLISH
Operating components
Function
Power onz
Power standbyz
Switch channels (up/down)
Menu
Cursor operation
Setup
Enter setting
Return
6 7
Manual search
(fast-reverse/fast-forward)
1
8 9
3
2
0 – 9, +10
TV POWER
TV INPUT
Playback
Auto search (cue)
Pause
Stop
Channel selection
TV power on/standby (Default : SONY)
Switch TV input (Default : SONY)
Function
Power onz
Power standbyz
Switch channels (up/down)
Menu
Cursor operation
Enter setting
Guide
Return
6 7
Manual search
(fast-reverse/fast-forward)
1
8 9
3
2
0 – 9, +10
TV POWER
TV INPUT
Playback
Auto search (cue)
Pause
Stop
Channel selection
TV power on/standby (Default : SONY)
Switch TV input (Default : SONY)
zThis
z
may power some devices on/standby.
seconds.
The zone mode indicator flashes twice.
2 Press ZONE SELECT.
3 Press 1 – 3 to set.
The zone mode indicator flashes twice.
seconds.
The zone mode indicator flashes twice.
2 Press 9, 8 and 1, in that order.
“MAIN” indicator flashes four times.
All the settings are restored to their
defaults.
The zone mode indicator flashes twice.
[Settable items]
1 When only using “MAIN ZONE”
2 When using “MAIN ZONE” / “ZONE2”
3 When using “MAIN ZONE” / “ZONE2” / “ZONE3” (Default)
Information
Operation buttons
ZONE/DEVICE ON
ZONE/DEVICE OFF
CH +, –
MENU
uio p
ENTER
SETUP
RETURN
and hold POWER ON and
1 Press
ZONE/DEVICE ON for at least 3
and hold POWER ON and
1 Press
ZONE/DEVICE ON for at least 3
Advanced version
nnSet top box for satellite (SAT) / cable (CBL) / IP
TV operation
When the ZONE SELECT button is pressed, only the set zone can be
operated with the remote control unit.
Resetting the remote control unit
Settings for the remote control unit are returned to the default setting.
Basic version
Operation buttons
ZONE/DEVICE ON
ZONE/DEVICE OFF
CH +, –
MENU
uio p
SETUP
ENTER
RETURN
Specifying the zone used with the
remote control unit
Simple version
nnTV operation
59
ENGLISH
Information
Information
Here, we list various information related to this unit.
Please refer to this information as needed.
F Part names and functions vpage 61
F Other information vpage 64
F Troubleshooting vpage 71
F Specifications vpage 73
F Index vpage 73
60
ENGLISH
Front panel
Display
For buttons not explained here, see the page indicated in parentheses ( ).
Q8 Q7
Q6
Q5
Q4
Q3
Q5
Q2
W2
W3 W4
w
qDecoder indicators
W5 W6 W7
These light when the respective decoders are
operating.
wInput signal indicators
eInformation display
r
t
y
qPower operation button
(ON/STANDBY)······································· (6, 11)
Turns power to this unit on and off (standby).
u
io
Q0
Q2V.AUX INPUT connectors··························· (17)
Remove the cap covering the connectors when
you want to use them.
wPower indicator··········································· (11)
eHeadphones jack
When the headphones are plugged into this
jack, audio will no longer be output from the
connected speakers or from the PRE OUT
connectors.
NOTE
To prevent hearing loss, do not raise the volume
level excessively when using headphones.
Q1
Q0
o i
u
The input source name, surround mode, setting
values and other information are displayed here.
rFront speaker indicator
This lights when audio signals are being output
from the speakers.
tQUICK SELECT indicators
The indicator corresponding to the memory
for which Quick Select function is set, lights
(“Quick select function” (vpage 34)).
yZONE2 indicator
Q3Master volume indicator
Q4Display·························································· (61)
Q5Remote control sensor······························· (64)
Q6TUNING PRESET button····························· (23)
Q7SOURCE SELECT knob························· (20, 35)
Q8ZONE2 SELECT button······························· (35)
Q9ZONE2 ON/OFF button······························· (35)
W0iPod PLAY button········································ (22)
W1SLEEP button··············································· (33)
W2RESTORER button······································· (48)
W3DYNAMIC EQ® button································ (46)
W4DYNAMIC VOLUME® button····················· (47)
W5MULTEQ® button·································· (46, 52)
W6DIMMER button··········································· (54)
W7STATUS button··········································· (55)
This lights up when ZONE2 (separate room)
power is turned on (vpage 35).
uMaster volume indicator
When performing setting operations, displays
the menu number.
iSleep timer indicator
This lights when the sleep mode is selected
(vpage 33).
oMUTE indicator
This lights when the mute mode is selected
(vpage 20).
e
r
t
y
Q0AUDYSSEY indicators
Lighting is as follows, depending on the setting
of “Dynamic EQ” (vpage 46) and “Dynamic
Volume” (vpage 47).
When
“Dynamic
EQ”
and
“Dynamic Volume” are “ON”.
When “Dynamic EQ” is “ON” and
“Dynamic Volume” is “OFF”.
When
“Dynamic
EQ”
and
“Dynamic Volume” are “OFF”.
Q1Surround back indicator
This lights when audio signals are being output
from the surround back speakers (vpage 49).
Q2Input mode indicators
Set the audio input modes for the different input
sources (vpage 42).
Q3RESTORER indicator
This lights when the RESTORER mode is
selected (vpage 48).
Q4HDMI indicator
This lights when playing using HDMI connections.
Q5Tuner reception mode indicators
These light according to the reception conditions
when the input source is set to “TUNER”.
STEREO: In the FM mode, this light when
receiving analog stereo broadcasts.
TUNED: Lights when the broadcast is properly
tuned in.
AUTO: This light when in the auto tuning mode.
61
Information
rQUICK SELECT buttons························ (34, 35)
tMENU button··············································· (39)
yCursor buttons (uio p)··················· (37 – 39)
uENTER button······································ (37 – 39)
iRETURN button··································· (37 – 39)
oSURROUND MODE buttons················· (24, 72)
Q0SETUP MIC jack······································· (8, 31)
Q1MASTER VOLUME control knob················ (20)
Q2
Advanced version
e
Q3
Basic version
Q9 W0 W1
Q4
Q1
q
q w
Simple version
Part names and functions
ENGLISH
Rear panel
See the page indicated in parentheses ( ).
Q2
q
Q1
w
Q0
e
qFM/AM antenna terminals······················································ (18)
wAnalog audio connectors··················································(16 – 18)
ePRE OUT connector························································ (5, 29, 30)
rS-VIDEO connector·································································· (18)
tVIDEO connectors······························································ (16, 17)
yCOMPONENT VIDEO connectors············································ (17)
62
rt
i
o
y
u
uSpeaker terminals·························································· (5, 29, 30)
iPower cord·················································································· (5)
oHDMI connectors······································································ (15)
Q0Digital audio connectors···················································· (16, 17)
Q1REMOTE CONTROL jacks························································ (19)
Q2DOCK CONTROL jack······························································· (18)
NOTE
Do not touch the inner pins of the connectors on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
ENGLISH
q
Q7
w
e
t
Q8
u
i
Q9
Q2Audyssey buttons··························· (46, 47, 52)
W0
W1
Q3Surround mode buttons······················· (24, 26)
•MULTEQ® button
•Dynamic EQ®/Dynamic Volume® button (DYN
EQ/VOL)
o
•STANDARD button
•Direct / Stereo button (D/ST)
•DSP simulation button (SIMULATION)
Q1
Q4SHIFT button·········································· (23, 38)
Q5TV operation buttons
W2
(TV POWER / INPUT)·································· (59)
Q3
W3
W4
Q5
Q6Remote control signal transmitter············ (64)
Q7Power buttons (POWER ON / OFF)······· (6, 11)
Q8Master volume control buttons (VOL)······ (20)
Q9Channel level button (CH LEVEL)·············· (33)
W0RETURN button··································· (37 – 39)
Information
W5
Q4
Advanced version
Tuner system buttons································· (23)
•FM/AM band switching button (BAND)
•Tuning mode button (MODE)
•Tuning down / Tuning up button (TUNING df)
y
Q2
NOTE
The SAT TU, PHONO, DVR, NET/USB, CD, PURE
DIRECT, MONITOR SELECT, A-DSX and PARTY
buttons cannot be used.
•Skip button (8, 9)
•Play button (1)
•Search button (6, 7)
•Pause button (3)
•Stop button (2)
r
Q0
W1ENTER button······································ (37 – 39)
W2RESTORER button······································· (48)
W3Number buttons······························ (23, 58, 59)
W4Character buttons······································· (38)
W5MEMORY button········································· (23)
W6Sleep timer button (SLEEP)························ (33)
Basic version
qZONE/DEVICE power buttons············· (35, 56)
wZone mode indicators··························· (35, 56)
eInput source select buttons·················· (19, 35)
rQUICK SELECT buttons························ (34, 35)
tMuting button (MUTE)························· (20, 35)
yChannel buttons (CH)···························· (23, 58)
uSOURCE SELECT button······················ (20, 35)
iMENU button··············································· (39)
oCursor buttons (uio p)··················· (37 – 39)
Q0SEARCH button······························ (21, 22, 39)
Q1System buttons························· (22, 23, 58, 59)
Q6
Simple version
Remote control unit
For buttons not explained here, see the page indicated in parentheses ( ).
W6
63
ENGLISH
Remote control unit
Inserting the batteries
q Slide the rear lid in the direction of the arrow and
remove it.
Operating range of the remote
control unit
Point the remote control unit at the remote sensor
when operating it.
w Load the two batteries properly as indicated by the
marks in the battery compartment.
30°
Other information
nn Trademark information (vpage 64)
nn Surround (vpage 65)
nn Explanation of terms (vpage 69)
30°
R6/AA
Approx. 23 ft /7 m
NOTE
e Put the rear cover back on.
NOTE
•Insert the specified batteries in the remote control unit.
•Replace the batteries with new ones if the set does
not operate even when the remote control unit is
operated close to the unit. (The supplied batteries are
only for verifying operation.)
•When inserting the batteries, be sure to do so in the
proper direction, following the q and w marks in the
battery compartment.
•To prevent damage or leakage of battery fluid:
•Do not use a new battery together with an old one.
•Do not use two different types of batteries.
•Do not attempt to charge dry batteries.
•Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
•If the battery fluid should leak, carefully wipe the fluid
off the inside of the battery compartment and insert
new batteries.
•Remove the batteries from the remote control unit if it
will not be in use for long periods.
•Used batteries should be disposed of in accordance
with the local regulations regarding battery disposal.
64
The set may function improperly or the remote control
unit may not operate if the remote control sensor is
exposed to direct sunlight, strong artificial light from an
inverter type fluorescent lamp or infrared light.
Trademark information
This product uses the following technologies:
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;
7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS and the Symbol are
registered trademarks, & DTS-HD, DTS-HD Master Audio, and the
DTS logos are trademarks of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries.
Manufactured under license from Audyssey Laboratories™. U.S.
and foreign patents pending. Audyssey MultEQ® is a registered
trademark of Audyssey Laboratories. Audyssey Dynamic EQ®
is a registered trademark of Audyssey Laboratories. Audyssey
Dynamic Volume® is a trademark of Audyssey Laboratories.
iPod is a trademark of Apple Inc., registered in the U.S. and other
countries.
iPhone is a trademark of Apple Inc.
•The iPod may only be used to copy or play content that are not
copyrighted or content for which copying or playback is legally
permitted for your private use as an individual. Be sure to comply
with applicable copyright legislation.
ENGLISH
Simple version
Surround
This unit is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.
Surround modes and surround parameters
This table shows the speakers that can be used in each surround mode and the surround parameters adjustable in each surround mode.
Symbols in the table
Channel output
Surround mode (vpage 24)
Front
L/R
Center
Surround
L/R
D
D
Surround Parameter (vpage 44)
Surround Back
L/R
S
DIRECT (Multi-channel)
S
STEREO
S
MULTI CH IN
S
D
D
DOLBY PRO LOGIC gz
S
D
D
DOLBY PRO LOGIC gx
S
D
D
DOLBY PRO LOGIC g
S
D
D
DTS NEO:6
S
D
D
D
DOLBY DIGITAL
S
D
D
D
DOLBY DIGITAL Plus
S
D
D
D
DOLBY TrueHD
S
D
D
D
DTS SURROUND
S
D
D
D
DTS 96/24
S
D
D
D
DTS-HD
S
D
D
D
DTS Express
S
D
D
D
MULTI CH STEREO
S
D
D
D
ROCK ARENA
S
D
D
D
JAZZ CLUB
S
D
D
D
MONO MOVIE
S
D
D
D
VIDEO GAME
S
D
D
MATRIX
S
D
D
VIRTUAL
S
D
Dz1
Dz3
S
S
D
S
S
S
D
S
S
S
S
Sz6
S
S
S
S
Sz7
Sz6
S
S
S
S
Dz2
D
D
D
Sz4
D
S
D
S
D
S
D
Dz2
Dz2
D
Dz2
Dz2
D
Dz2
Dz2
D
D
D
S
Effect Lev.
(vpage 44)
Room Size
(vpage 44)
S
Sz8
Sz8
Sz8
Sz8
Delay Time
(vpage 44)
S
S
S
S
S
S
S
S
S
S
D
Sz8
Sz8
S
S
Dz2
Dz2
D
Sz8
S
S
D
S
S
Dz2
Dz2
D
S
S
S
S
D
S
S
S
S
D
S
S
S
S
D
Dz2
Dz2
D
S
S
S
S
D
Dz2
D
Dz3
S
S
S
S
S
A signal for each channel contained in an input signal is output as audio.
If “Surround Parameter” – “Front Height” (vpage 45) is set to “ON”, sound is output from the front height speakers.
Only when “Subwoofer Mode” is set to “LFE+Main” (vpage 50), sound is output from the subwoofer.
If this surround mode is selected, only the “Height” mode setting is available for “Surround Parameter” – “Mode” (vpage 44).
For HD Audio whose sampling frequency of an input signal is more than 96kHz, this sound parameter cannot be set.
This item can be selected when “Surround Parameter” – “Mode” (vpage 44) is set to “Cinema”.
This item can be selected when “Surround Parameter” – “Mode” (vpage 44) is set to “Cinema” or “Pro Logic”.
This item cannot be set when “Surround Parameter” – “S.Back” (vpage 45) is set to “PLgx Music”.
This item can be selected when a Dolby TrueHD signal is played.
This item can be selected when a Dolby Digital or DTS signal is played.
This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
Information
z1
z2
z3
z4
z5
z6
z7
z8
z9
z10
z11
Dz1
LFE
z11
(vpage 44)
D. Comp
z10
(vpage 44)
Subwoofer
Cinema EQ.
z5
(vpage 44)
Advanced version
DIRECT (2channel)
Front Height L/R
DRC
z9
(vpage 44)
Mode
(vpage 44)
Basic version
S This indicates the audio output channels or surround parameters that can be set.
D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.” (vpage 49).
65
ENGLISH
Surround
Surround Parameter (vpage 44)
PRO LOGIC g/gx Music mode only
Surround mode (vpage 24)
AFDM
z12
(vpage 44)
S.Back
(vpage 45)
Front Height
z13
(vpage 45)
Height Gain
(vpage 45)
Subwoofer
(vpage 45)
Panorama
(vpage 44)
Dimension
(vpage 44)
Center Width
(vpage 44)
NEO:6 Music
mode only
Center Image
(vpage 44)
Audyssey Settingsz20 (vpage 46)
Tone
z15
(vpage 45)
MultEQ®
(vpage 46)
Dynamic EQ®
z17
(vpage 46)
Dynamic
Volume®
z18
(vpage 47)
S
S
S
S
S
S
S
S
RESTORER
z19
(vpage 48)
Sz3
DIRECT (2 channel)
DIRECT (Multi-channel)
STEREO
MULTI CH IN
S
S
DOLBY PRO LOGIC gz
DOLBY PRO LOGIC gx
S
DOLBY PRO LOGIC g
S
DTS NEO:6
S
S
Sz14
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
Sz14
Sz14
S
S
S
S
S
S
S
S
Sz14
Sz14
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
DOLBY DIGITAL
S
S
S
DOLBY DIGITAL Plus
S
S
S
DOLBY TrueHD
S
S
S
DTS SURROUND
S
S
S
DTS 96/24
S
S
S
DTS-HD
S
S
S
Sz14
Sz14
DTS Express
S
S
S
Sz14
MULTI CH STEREO
S
S
ROCK ARENA
S
S
S
Sz16
JAZZ CLUB
S
S
S
S
S
S
S
MONO MOVIE
S
S
S
S
S
S
S
VIDEO GAME
S
S
S
S
S
S
S
MATRIX
S
S
S
S
S
S
S
S
S
S
S
S
VIRTUAL
z3
z12
z13
z14
z15
z16
z17
z18
z19
z20
66
Only when “Subwoofer Mode” is set to “LFE+Main” (vpage 50), sound is output from the subwoofer.
This item can be selected when a Dolby Digital or DTS or DVD-Audio signal is played.
If “Speaker Config.” – “Front Height” (vpage 49) is set to “None”, this item cannot be selected.
This item can be selected when “Surround Parameter” – “Front Height” (vpage 45) is set to “ON”.
This item cannot be set when “Dynamic EQ” (vpage 46) is set to “ON”.
In this surround mode, bass is +6 dB, and treble is +4 dB. (Default)
This item cannot be set when “MultEQ” (vpage 46) is set to “OFF” or “Manual”.
This item cannot be set when “Dynamic EQ” (vpage 46) is set to “OFF”.
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
For HD Audio whose sampling frequency of an input signal is more than 96 kHz, this sound parameter cannot be set.
ENGLISH
Surround
Simple version
nnTypes of input signals, and corresponding surround modes
This table shows the input signal that can be played in each surround mode. Check the audio signal of the input source then select the surround mode.
Symbols in the table
F This indicates the default surround mode.
D This indicates the surround mode that is fixed when “AFDM” (vpage 44) is set to “ON”.
S This indicates the selectable surround mode.
Input signal types and formats
Surround mode (vpage 24)
ANALOG
LINEAR PCM LINEAR PCM
(multi ch)
(2ch)
DTS-HD
Master
Audio
DTS
DTS-HD
High
Resolution
Audio
DTS
EXPRESS
DTS ES
DSCRT
(With Flag)
DTS ES
MTRX
(With Flag)
DOLBY
DTS
(5.1ch)
DTS 96/24
DOLBY
TrueHD
DOLBY DIGITAL
DOLBY
DOLBY
DOLBY
DIGITAL EX
DIGITAL EX
DIGITAL Plus
(With no
(With Flag)
Flag)
DOLBY
DIGITAL
(5.1/5/4ch)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
F
F
z1z3
z1z3
FD
z2z3
z1z3
z4
z1z3
S
S
S
S
S
S
S
S
S
S
S
S
S
F
S
S
FD
S
F
S
S
S
S
S
S
S
S
S
F
S
S
S
S
S
S
S
S
Advanced version
S
S
F
F
z1z3
z1z3
z2z3
z1z3
z4
z1z3
z1z3
z1z3
z4
z1
z2
z3
z4
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
FD
S
S
F
S
S
S
F
S
S
S
F
S
S
S
S
S
S
S
S
S
S
S
Information
DTS SURROUND
DTS-HD MSTR
DTS-HD HI RES
DTS ES DSCRT6.1
DTS ES MTRX6.1
DTS SURROUND
DTS 96/24
DTS (–HD) + PLgx CINEMA
DTS (–HD) + PLgx MUSIC
DTS (–HD) + PLgz
DTS EXPRESS
DTS (–HD) + NEO:6
DTS NEO:6 CINEMA
DTS NEO:6 MUSIC
DOLBY SURROUND
DOLBY TrueHD
DOLBY DIGITAL+
DOLBY DIGITAL EX
DOLBY (D+) (HD) +EX
DOLBY DIGITAL
DOLBY (D) (D+) (HD) +PLgx CINEMA
DOLBY (D) (D+) (HD) +PLgx MUSIC
DOLBY (D) (D+) (HD) +PLgz
DOLBY PRO LOGIC gx CINEMA
DOLBY PRO LOGIC gx MUSIC
DOLBY PRO LOGIC gx GAME
DOLBY PRO LOGIC gz
DOLBY PRO LOGIC g CINEMA
DOLBY PRO LOGIC g MUSIC
DOLBY PRO LOGIC g GAME
DOLBY PRO LOGIC
NOTE
DTS-HD
Basic version
PCM
If “Speaker Config.” – “S.Back” (vpage 49) is set to “None”, this surround mode cannot be selected.
If “Speaker Config.” – “S.Back” (vpage 49) is set to “1sp” or “None”, this surround mode cannot be selected.
This item can be selected when “Amp Assign” (vpage 49) is set to “Normal”.
If “Speaker Config.” – “Front Height” (vpage 49) is set to “None”, this surround mode cannot be selected.
67
ENGLISH
Surround
Input signal types and formats
PCM
Surround mode (vpage 24)
MULTI CH IN
MULTI CH IN
MULTI CH IN + PLgx CINEMA
MULTI CH IN + PLgx MUSIC
MULTI CH IN + PLgz
MULTI CH IN + Dolby EX
MULTI CH IN 7.1
DIRECT
DIRECT
DSP SIMULATION
MULTI CH STEREO
ROCK ARENA
JAZZ CLUB
MONO MOVIE
VIDEO GAME
MATRIX
VIRTUAL
STEREO
STEREO
NOTE
LINEAR PCM LINEAR PCM
(multi ch)
(2ch)
DTS
DTS-HD
Master
Audio
DTS-HD
High
Resolution
Audio
S
S
DOLBY
DTS
EXPRESS
DTS ES
DSCRT
(With Flag)
DTS ES
MTRX
(With Flag)
DTS
(5.1ch)
DTS 96/24
DOLBY
TrueHD
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
DOLBY DIGITAL
DOLBY
DOLBY
DOLBY
DIGITAL EX
DIGITAL EX
DIGITAL Plus
(With no
(With Flag)
Flag)
DOLBY
DIGITAL
(5.1/5/4ch)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
F
S
S
S
S
F D (7.1)
z2z3
z1z3
z4
z1z3
z3
z1
z2
z3
z4
68
ANALOG
DTS-HD
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
F
S
F
S
S
S
If “Speaker Config.” – “S.Back” (vpage 49) is set to “None”, this surround mode cannot be selected.
If “Speaker Config.” – “S.Back” (vpage 49) is set to “1sp” or “None”, this surround mode cannot be selected.
This item can be selected when “Amp Assign” (vpage 49) is set to “Normal”.
If “Speaker Config.” – “Front Height” (vpage 49) is set to “None”, this surround mode cannot be selected.
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
ENGLISH
DTS Digital Surround
DTS Digital Surround is the standard digital surround
format of DTS, Inc., compatible with a sampling
frequency of 44.1 or 48 kHz and up to 5.1 channels
of digital discrete surround sound.
DTS-ES™ Discrete 6.1
DTS-ES™ Discrete 6.1 is a 6.1-channel discrete
digital audio format adding a surround back (SB)
channel to the DTS digital surround sound.
Decoding of conventional 5.1-channel audio signals
is also possible according to the decoder.
DTS-ES™ Matrix 6.1
DTS-ES™ Matrix 6.1 is a 6.1-channel discrete digital
audio format inserting a surround back (SB) channel
to the DTS digital surround sound through matrix
encoding. Decoding of conventional 5.1-channel
audio signals is also possible according to the
decoder.
DTS Express
DTS Express is an audio format supporting low bit
rates (max. 5.1 channels, 24 to 256 kbps).
DTS-HD
This audio technology provides higher sound quality
and enhanced functionality than the conventional
DTS and is adopted as an optional audio for Blu-ray
Disc. This technology supports multi-channel, high
data transfer speed, high sampling frequency, and
lossless audio playback. Maximum 7.1-channels are
supported in Blu-ray Disc.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is an improved
version of the conventional DTS, DTS-ES and
DTS 96/24 signals formats, compatible with
sampling frequencies of 96 or 48 kHz and up to
7.1 channels of discrete digital sound. High data
bit rate performance provides high quality sound.
This format is fully compatible with conventional
products, including conventional DTS digital
surround 5.1-channel data.
DTS-HD Master Audio
DTS-HD Master Audio is DTS, Inc’s lossless audio
format compatible with up to 96 kHz/7.1 channels.
The lossless audio coding technology faithfully
reproduces the sound of the studio master. It is fully
compatible with conventional products, including
conventional DTS digital surround 5.1-channel data.
69
Information
Dolby Pro Logic gx
Dolby Pro Logic gx is a further improved version of
the Dolby Pro Logic g matrix decoding technology.
Audio signals recorded in 2 channels are decoded
to achieve a natural sound with up to 7.1 channels.
There are three modes: “Music” suited for playing
music, “Cinema” suited for playing movies, and
“Game” which is optimized for playing games.
Dolby Pro Logic gz
Dolby Pro Logic gz introduces a new dimension to
Home Entertainment through the addition of a pair
of front height channels. Compatible with stereo,
5.1-channel and 7.1-channel content, Dolby Pro
Logic gz provides enhanced spaciousness, depth
and dimension to movies, concert video and video
game playback while maintaining the full integrity
of the source mix.
Dolby Pro Logic gz identifies and decodes spatial
cues that occur naturally in all content, directing
this information to the front height channels,
complementing the performance of left and right
surround sound speakers. Content that is encoded
with Dolby Pro Logic gz height channel information
can be even more revealing, with perceptually
discrete height channel information bringing an
exciting new dimension to home entertainment.
Dolby Pro Logic gz, with front height channels is
also an ideal alternative for households that cannot
support the placement of back surround speakers
of a typical 7.1-channel system but may have
bookshelf space available to support the addition of
height speakers.
Downmix
This function converts the number of channels of
surround audio to less number of channels and
plays back.
DTS
This is an abbreviation of Digital Theater System,
which is a digital audio system developed by DTS.
When playing back audio by connecting this system
with a device such as DTS amplifier, accurate sound
field position and realistic sound effect as if you are
in a movie theater can be obtained.
DTS 96/24
DTS 96/24 is a digital audio format enabling high
sound quality playback in 5.1 channels with a
sampling frequency of 96 kHz and 24 bit quantization
on DVD-Video.
Advanced version
D
Deep Color
This technology allows expression of more number
of colors than the conventional 8 bits and can
reproduce colors close to natural ones without color
streak.
Dolby Digital
Dolby Digital is a multi-channel digital signal format
developed by Dolby Laboratories.
A total of 5.1 channels are played: 3 front channels
(“FL” , “FR” and “C”), 2 surround channels
(“SL” and “SR”) and the “LFE” channel for low
frequencies.
Because of this, there is no crosstalk between
channels and a realistic sound field with a “threedimensional” feeling (sense of distance, movement
and positioning) is achieved.
A realistic, powerful sense of presence is achieved
when playing movie sources in AV rooms as well.
Dolby Digital EX
Dolby Digital EX is a 6.1-channel surround format
proposed by Dolby Laboratories that allows users
to enjoy in their homes the “DOLBY DIGITAL
SURROUND EX” audio format jointly developed by
Dolby Laboratories and Lucas Films.
The 6.1 channels of sound, including surround back
channels, provide improved sound positioning and
expression of space.
Dolby Digital Plus
Dolby Digital Plus is an improved Dolby Digital signal
format that is compatible with up to 7.1 channels
of discrete digital sound and also improves sound
quality thanks to extra data bit rate performance.
It is upwardly compatible with conventional Dolby
Digital, so it offers greater flexibility in response to
the source signal and the conditions of the playback
equipment.
Dolby TrueHD
Dolby TrueHD is a high definition audio technology
developed by Dolby Laboratories, using lossless
coding technology to faithfully reproduce the sound
of the studio master.
This format is compatible with a maximum sampling
frequency of 96 kHz and up to 7.1 channels, so it is
used for applications particularly prioritizing sound
quality.
Dolby Pro Logic g
Dolby Pro Logic g is a matrix decoding technology
developed by Dolby Laboratories.
Regular music such as that on CDs is encoded into
5 channels to achieve an excellent surround effect.
The surround channel signals are converted into
stereo and full band signals (with a frequency
response of 20 Hz to 20 kHz or greater) to create
a “three-dimensional” sound image offering a rich
sense of presence for all stereo sources.
Basic version
A
Adobe RGB color / Adobe YCC601 color
Like x.v.Color, each of these color spaces defines
a palette of available colors that is larger than the
traditional RGB color model.
Audyssey Dynamic EQ®
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased
by taking into account human perception and room
acoustics. Audyssey Dynamic EQ works in tandem
with Audyssey MultEQ® to provide well-balanced
sound for every listener at any volume level.
Audyssey Dynamic Volume®
Audyssey Dynamic Volume solves the problem of
large variations in volume level between television
programs, commercials, and between the soft and
loud passages of movies. Audyssey Dynamic EQ
is integrated into Dynamic Volume so that as the
playback volume is adjusted automatically, the
perceived bass response, tonal balance, surround
impression, and dialog clarity remain the same.
Audyssey MultEQ®
Audyssey MultEQ is a room equalization solution
that calibrates any audio system so that it can
achieve optimum performance for every listener
in a large listening area. Based on several room
measurements, MultEQ calculates an equalization
solution that corrects for both time and frequency
response problems in the listening area and also
performs a fully automated surround system setup.
Auto Lip Sync
If you connect the receiver to a TV that supports the
Auto Lip Sync function, it can automatically correct
delay between the audio and video.
Simple version
Explanation of terms
ENGLISH
Explanation of terms
DTS NEO:6™ Surround
DTS NEO:6™ is a matrix decoding technology
for achieving 6.1-channel surround playback
with 2-channel sources. It includes “DTS NEO:6
Cinema” suited for playing movies and “DTS
NEO:6 Music” suited for playing music.
Dynamic range
The difference between the maximum undistorted
sound level and the minimum discernible level
above the noise emitted by the device.
H
HDCP
When transmitting digital signals between devices,
this copyright protection technology encrypts
the signals to prevent content from being copied
without authorization.
HDMI
This is an abbreviation of High-Definition Multimedia
Interface, which is an AV digital interface that can
be connected to a TV or amplifier. Video signal and
audio signal can be connected using 1 cable.
L
LFE
This is an abbreviation of Low Frequency Effect,
which is an output channel that emphasizes
low frequency effect sound. Surround audio is
intensified by outputting 20 Hz to 120 Hz deep
bass.
M
MAIN ZONE
The room where this unit is placed is called the
MAIN ZONE.
MP3 (MPEG Audio Layer-3)
This is an internationally standardized audio data
compression scheme, using the “MPEG-1” video
compression standard. It compresses the data
volume to about one eleventh its original size while
maintaining sound quality equivalent to a music CD.
MPEG (Moving Picture Experts Group), MPEG-2,
MPEG-4
These are the names for digital compression format
standards used for the encoding of video and audio.
Video standards include “MPEG-1 Video”, “MPEG2 Video”, “MPEG-4 Visual”, “MPEG-4 AVC”. Audio
standards include “MPEG-1 Audio”, “MPEG-2
Audio”, “MPEG-4 AAC”.
70
P
Progressive (sequential scanning)
This is a scanning system of video signal that
displays 1 frame of video as one image. Compared
to the interlace system, this system provides
images with less flickering and bleeding.
Protection Circuit
This is a function to prevent damage to components
within the power supply when an abnormality
such as an overload, excess voltage occurs or
temperature for any reason.
In this unit, the power indicator blinks and the unit
enters standby mode when an abnormality occurs.
S
Sampling frequency
Sampling involves taking a reading of a sound wave
(analog signal) at regular intervals and expressing
the height of the wave at each reading in digitized
format (producing a digital signal).
The number of readings taken in one second is
called the “sampling frequency”. The larger the
value, the closer the reproduced sound is to the
original.
Speaker impedance
This is an AC resistance value, indicated in Ω
(ohms). Greater power can be obtained with this
value smaller.
sYCC601 color
Like x.v.Color, each of these color spaces defines
a palette of available colors that is larger than the
traditional RGB color model.
W
WMA (Windows Media Audio)
This is audio compression technology developed by
Microsoft Corporation.
WMA data can be encoded using Windows
Media® Player Ver.7, 7.1, Windows Media®Player
for Windows® XP and Windows Media® Player 9
Series.
To encode WMA files, only use applications
authorized by Microsoft Corporation. If you use
an unauthorized application, the file may not work
properly.
X
x.v.Color
This function lets HDTVs display colors more
accurately. It enables display with natural, vivid
colors. “x.v.Color” is a Sony registered trademark.
Z
ZONE2
This unit can operate in a room other than the room
where this unit is placed (MAIN ZONE) (ZONE2
playback). The room for ZONE2 playback is called
ZONE2.
ENGLISH
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
GAudioH
Symptom
Page
•Check the connections for all devices.
•Check the speaker connections.
•Check whether the audio device power is turned on.
•Adjust the master volume.
•Cancel the mute mode.
•Select a suitable input source.
•Select a suitable input mode.
•Disconnect the headphones. No sound is output from the speakers
or the PRE OUT connectors when headphones are connected.
5, 15 – 18
5, 29, 30
6
20, 35
20, 35
20, 35
42
61
No sound is
produced from
surround speaker.
•Check if the surround speakers are connected to the SURROUND
terminals.
–
No sound is
produced from
surround back
speaker.
•Set “Amp Assign” on the menu to “Normal”.
•Set “Speaker Config.” – “S.Back” on the menu to something
other than “None”.
•Set “Surround Parameter” – “S.Back” on the menu to something
other than “OFF”.
•Set the surround mode to something other than “STEREO”.
49
49
No sound is
produced from front
height speaker.
•Set “Surround Parameter” – “Front Height” on the menu to
“ON”.
•Set “Amp Assign” on the menu to “Front Height”.
•Set “Speaker Config.” – “Surround” on the menu to something
other than “None”.
45
No sound is
produced from
subwoofer.
•Check the subwoofer connections.
•Turn on the subwoofer’s power.
•Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”.
•If “Front” and “Center” for “Speaker Config.” are set to “Large”,
and “Subwoofer Mode” is set to “LFE”, no sound may be output
from the subwoofers, depending on the input signal or selected
surround mode.
5, 29, 30
6
49
49, 50
DTS sound is not
output.
•Set “Decode Mode” on the menu to “Auto” or “DTS”.
42
Dolby TrueHD, DTSHD, Dolby Digital
Plus audio is not
output.
•Make HDMI connections.
14
GGeneralH
Symptom
Cause/Solution
Page
Power does not turn
on.
•Check whether the power plug is correctly inserted into the power
outlet.
•The protection circuit is active. Disconnect the power plug from
the electric outlet, wait 5 to 10 seconds and then insert it back
into the outlet.
5
5, 70
•Set “Display” on the menu to something other than “OFF”.
The power indicator
is blinking red
in intervals of
approximately 2
seconds.
•The temperature inside the unit has risen. Please turn off power
once, and re-apply the power after the temperature has fallen
sufficiently.
•Please re-install this unit in a place having good ventilation.
–
The power indicator
is blinking red
in intervals of
approximately 0.5
seconds.
•Please use speakers which have the specified impedance.
•The speaker cable has shorted (is touching). Firmly twist the core
wire in the speaker cable, and then re-connect it to the speaker
terminal.
4
4
After turning on the
power, the power
indicator is blinking
red in intervals of
approximately 0.5
seconds.
•This unit amplifier circuit has failed. Turn off the power and please
contact the DENON service adviser.
–
Set does not operate •Reset the microprocessor.
properly.
54
–
72
GVideoH
Symptom
•Check the TV connection.
•Set the TV input correctly.
Page
5
6
24
49
49
Information
No picture appears.
Cause/Solution
45
Advanced version
Display is off.
Basic version
Cause/Solution
Audio is not output.
Simple version
Troubleshooting
71
ENGLISH
GRemote control unitH
GHDMIH
Symptom
No audio is
output with HDMI
connection.
No video is
output with HDMI
connection.
Cause/Solution
Page
•Check the connection of the HDMI connectors.
•When outputting HDMI audio from the speakers, set “HDMI
Audio Out” on the menu to “Amp”.
•When outputting HDMI audio from a TV, set “HDMI Audio Out”
on the menu to “TV”.
14
51
•Check the connection of the HDMI connectors.
•Set the input source to match the connected HDMI connector.
•Check whether the TV is compatible with copyright protection
(HDCP). If connected to a device not compatible with HDCP, video
will not be output correctly.
14
14, 19, 20
14
When the following
•Set “HDMI Control” on the menu to “OFF”. To operate power
operations are
only for each device, set “Power Off Control” to “OFF”.
performed on
devices compatible
with HDMI control,
the same operations
occur on this unit.
•Power ON/OFF
•Switching
audio
output devices
•Adjust volume
•Switch input source
51
32, 51
Symptom
The set cannot be
operated with the
remote control unit.
Cause/Solution
Page
•Batteries are worn out. Replace with new batteries.
•Operate the remote control unit within a distance of about 23 ft /
7 m from this unit and at an angle of within 30°.
•Remove any obstacle between this unit and the remote control
unit.
•Insert the batteries in the proper direction, checking the q and
w marks.
•The set’s remote control sensor is exposed to strong light (direct
sunlight, inverter type fluorescent bulb light, etc.). Move the set
to a place in which the remote control sensor will not be exposed
to strong light.
64
64
64
64
64
Resetting the microprocessor
Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
ON/STANDBY
SURROUND MODE 1
GRadioH
Symptom
Cause/Solution
Reception fails, or
•Change the antenna orientation or position.
there is a lot of noise •Separate the AM loop antenna from the unit.
or distortion.
•Use an FM outdoor antenna.
•Separate the antenna from other connection cables.
Page
18
18
18
18
GiPodH
Symptom
Cause/Solution
Page
iPod cannot be
played.
•Check the iPod connections.
•Plug the control dock for iPod’s AC adapter into a power outlet.
•Switch the input source to “DOCK”.
“Connection Error”
is displayed.
•Unable to communicate properly. Turn off the power to this unit,
disconnect the iPod and then reconnect it.
–
“Not Support” is
displayed.
•The iPod connected to the unit is not compatible. Please make
sure the iPod you are connecting is compatible.
•The software version of the connected iPod is an old one. Please
update to the latest version.
21
•The iPod is not responding. Turn off the power to this unit,
disconnect the iPod and then reconnect it.
–
“Connection Error”
is displayed.
72
18
–
19, 20
SURROUND MODE 0
1 Turn off the power using ON/STANDBY.
ON/STANDBY while simultaneously pressing SURROUND MODE 0 and
2 Press
SURROUND MODE 1.
the display starts flashing at intervals of about 1 second, release the two
3 Once
buttons.
–
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
ENGLISH
Index
vvNumerics
2.1-channel·························································· 30
2ch DIRECT/STEREO·········································· 52
3D········································································ 14
5.1-channel···························································· 4
6.1-channel···················································· 28, 29
7.1-channel···················································· 28, 29
nn Audio section
•Power amplifier
Rated output:
vvA
200 mV/47 kΩ
10 Hz – 100 kHz — +1, –3 dB (DIRECT mode)
98 dB (IHF–A weighted, DIRECT mode)
nn Video section
nn Tuner section
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
S/N (IHF-A):
Total harmonic Distortion (at 1 kHz):
1 Vp-p, 75 Ω
5 Hz – 10 MHz — +1, –3 dB
[FM]
(Note: μV at 75 Ω, 0 dBf = 1 x 10–15 W)
87.5 MHz – 107.9 MHz
1.2 μV (12.8 dBf)
MONO 2.8 μV (20.2 dBf)
MONO 70 dB
STEREO 67 dB
MONO 0.7 %
STEREO 1.0 %
[AM]
520 kHz – 1710 kHz
18 μV
nn General
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
AC 120 V, 60 Hz
450 W
0.1 W (Standby)
3 W (CEC standby)
434 (W) x 171 (H) x 381 (D) mm (17-3/32” x 6-47/64” x 15”)
9.2 kg (20 lbs 4.5 oz)
Batteries:
Maximum external dimensions:
Weight:
R6/AA Type (two batteries)
53 (W) x 224 (H) x 28 (D) mm (2-3/32” x 8-13/16” x 1-7/64”)
160 g (Approx 5.6 oz, including batteries)
For purposes of improvement, specifications and design are subject to change without notice.
banana plug··························································· 4
Base Curve Copy················································· 47
Bass···································································· 45
Bass Setting························································ 50
Bi-amp································································· 30
Browse mode······················································ 21
vvC
Cable
Audio cable··············································5, 16, 17
Coaxial digital cable·········································· 17
Component video cable···································· 17
HDMI cable··················································· 5, 15
Optical cable····················································· 16
Speaker cable····················································· 5
Video cable··················································16, 17
Center Image······················································ 44
Center Width······················································· 44
Channel Level······················································ 50
Characters··························································· 38
73
Information
nn Remote Control Unit (RC-1146)
vvB
vvD
D.Comp······························································· 44
Decode Mode····················································· 42
Deep Color···················································· 14, 69
DENON original surround mode·························· 26
Dimension··························································· 44
Display··························································· 54, 61
Distance······························································ 50
Dolby
Dolby Digital··············································· 25, 69
Dolby Digital EX·········································· 25, 69
Dolby Digital Plus········································ 25, 69
Dolby Pro Logic II·············································· 69
Dolby Pro Logic IIx············································ 69
Dolby Pro Logic IIz······································ 28, 69
Dolby TrueHD·············································· 25, 69
Downmix····························································· 69
DRC····································································· 44
DTS······························································· 25, 69
DTS 96/24··················································· 25, 69
DTS-ES Discrete 6.1··································· 25, 69
DTS-ES Matrix 6.1······································ 25, 69
DTS-HD······················································· 25, 69
DTS-HD High Resolution Audio························ 69
DTS-HD Master Audio······································ 69
DTS Digital Surround········································ 69
DTS Express····················································· 69
DTS NEO:6™ Surround······························ 24, 70
Dynamic EQ························································ 46
Dynamic range···················································· 70
Dynamic Volume················································· 47
Advanced version
•Standard video connectors
Input/output level and impedance:
Frequency response:
Accessories··························································· 1
Adjust CH···························································· 47
Adobe RGB color / Adobe YCC601 color············ 69
AFDM·································································· 44
Amp Assign························································· 49
ARC····································································· 15
Audio Adjust························································ 43
Audio cable················································ 5, 16, 17
Audio Delay························································· 48
Audio Setup························································· 52
Audyssey Auto Setup······································ 6, 31
Audyssey Dynamic EQ·································· 46, 69
Audyssey Dynamic Volume·························· 47, 69
Audyssey MultEQ··································· 46, 61, 69
Audyssey Settings·············································· 46
Auto Lip Sync················································ 51, 69
Auto Preset························································· 40
Auto Setup······················································ 6, 31
Auto Surround Mode··········································· 52
Basic version
Output connectors:
•Analog
Input sensitivity/Input impedance:
Frequency response:
S/N:
Front:
75 W + 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
110 W + 110 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
Center:
75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
110 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround:
75 W + 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
110 W + 110 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround back:
75 W + 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
110 W + 110 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
6 – 16 Ω
Simple version
Specifications
Cinema EQ·························································· 44
Coaxial digital cable············································· 17
Component video cable······································ 17
Condensation························································ 2
Connection
Antenna···························································· 18
Blu-ray Disc player······································ 15, 16
Cable TV···························································· 17
Control dock for iPod········································· 18
Digital camcorder·············································· 17
DVD player·················································· 15, 16
External control device····································· 19
Game console··················································· 15
HDMI································································ 14
Power cord·························································· 5
Satellite tuner···················································· 17
Set-top box··················································15, 17
Speaker························································· 4, 29
TV··························································· 5, 15, 16
Crossover Frequency·········································· 50
ENGLISH
vvE
Effect Lev.··························································· 44
EQ Customize····················································· 52
Error messages (Auto Setup)······························ 10
vvF
FM indoor antenna·············································· 18
Front A/B (connection)·································· 28, 30
Front Height·················································· 45, 49
Front height speaker····································· 28, 29
Front Panel·························································· 61
Front Speaker Setup··········································· 51
vvH
HDCP···························································· 14, 70
HDMI····························································· 14, 70
HDMI 1.4······················································· 14, 15
HDMI Audio Out················································· 51
HDMI cable····················································· 5, 15
HDMI Control················································ 32, 51
HDMI Setup························································ 51
Headphones························································ 61
Height Gain························································· 45
vvI
Information·························································· 55
Audio Input Signal············································· 55
Auto Surround Mode········································ 55
HDMI Information············································· 55
Preset Channel················································· 55
Quick Select······················································ 55
Status································································ 55
Input Assign························································ 41
Input Mode·························································· 42
Input Setup·························································· 39
Input signal···················································· 25, 67
iPod PLAY··························································· 22
vvL
Level Lch····························································· 53
Level Rch···························································· 53
LFE································································ 44, 70
Listening mode··················································· 24
Listening position·················································· 7
vvM
MAIN ZONE·················································· 34, 70
Manual EQ·························································· 47
Manual Setup······················································ 48
Master volume display········································ 54
Menu map··························································· 36
74
Mode··································································· 44
MP3····································································· 70
MPEG·································································· 70
MultEQ································································ 46
Mute Level·························································· 53
vvO
On-Screen Display··············································· 53
Optical cable························································ 16
Option Setup······················································· 53
Display······························································ 54
On-Screen Display············································ 53
Quick Select Name··········································· 54
Remote Preset Codes······································ 54
Setup Lock························································ 54
Source Delete··················································· 53
Volume Control················································· 53
Zone Rename··················································· 54
vvP
Panorama···························································· 44
Parameter Check················································· 10
Playback
Blu-ray Disc player············································ 20
Control dock for iPod········································· 21
Direct································································ 26
DVD player························································ 20
FM/AM broadcasts··········································· 23
Standard··························································· 24
Stereo······························································· 26
ZONE2······························································ 35
Playback Mode (Control dock for iPod)··············· 43
Power Off Control··············································· 51
Power On Level·················································· 53
Preset codes················································· 54, 56
Preset Name······················································· 41
Preset Skip·························································· 40
Presetting radio stations····································· 23
Progressive························································· 70
Protection circuit················································· 70
vvQ
Quick Select························································ 55
Quick Select Name············································· 54
vvR
Rear panel··························································· 62
Reference Level Offset······································· 46
Remote control unit······································ 56, 63
Inserting the batteries······································· 64
Operating components····································· 58
Registering Preset Codes································· 56
Remote mode····················································· 21
Remote Preset Codes········································· 54
Rename······························································· 43
Repeat································································· 43
Resetting the microprocessor····························· 72
RESTORER·························································· 48
Room Size··························································· 44
vvS
Sampling frequency············································ 70
S.Back··························································· 45, 49
Screensaver························································ 53
Selecting the input source·································· 19
Setup Lock·························································· 54
Shuffle································································· 43
Sleep timer·························································· 33
Source Delete····················································· 53
Source Level······················································· 43
Speaker
Connect························································ 4, 29
Install···························································· 4, 28
Set up··························································· 6, 31
Speaker cable························································ 5
Speaker Config.··················································· 49
Speaker impedance········································· 4, 70
Speaker Setup····················································· 49
Standby Source··················································· 51
Subwoofer··························································· 45
Subwoofer setting················································· 7
Surround back speaker·································· 28, 29
Surround Mode············································· 24, 65
Surround Parameter············································ 44
sYCC601 color····················································· 70
vvT
Tone···································································· 45
Tone Control························································ 45
Trademark··························································· 64
Treble·································································· 45
Turn off power (standby)····································· 11
Turn on power······················································· 6
vvV
Video··································································· 42
Video cable···················································· 16, 17
Video conversion················································· 13
Video Mode························································· 42
Video Select························································ 42
Volume Control··················································· 53
Volume Limit······················································· 53
vvW
WMA··································································· 70
vvX
x.v.Color······························································ 70
vvZ
ZONE2····················································· 34, 61, 70
ZONE2 Setup······················································ 53
Zone Rename······················································ 54
www.denon.com
D&M Holdings Inc.
Printed in China 5411 10410 005D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising