HP | Integrity rx2600 | System information | HP Integrity rx2600 System information

HP Integrity rx2600 System information
Upgrade Guide
HP Integrity rx2600 / HP 9000 rp34x0 to
HP Integrity rx2620
Manufacturing Part Number: AB359-90002
Second Edition
June 2005
© Copyright 2005 Hewlett-Packard Development Company, L.P.
Legal Notices
© Copyright 2005 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an additional
warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
2
Contents
1. HP Integrity rx2620 Upgrade
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Time Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Upgrade Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Upgrade Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Upgrade Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Service Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Safety and Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Communications Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Upgrade Preparation and System Shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Firmware Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LAN Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Back Up Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
System Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
System Hardware Component Upgrade Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Removing System Top Metal Cover and Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Removing System Fans, PCI Card Cage, Airflow Guides, Memory, Processors, and the Management
Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Upgrading the System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Upgrading the CPUs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Reinstalling System Fans, PCI Card Cage, Airflow Guides, Memory, and the Management Processor
50
Upgrade CPU Fans (1A and 1B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Installing HP Integrity rx2620 Name Plate and Intel Itanium 2 Rack Label . . . . . . . . . . . . . . . . . . 55
Apply UUID Label (rp34x0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Replacing the Front Bezel and Top Metal Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
System Validation and Reconfiguration Procedures After Hardware Upgrade from rx2600 . . . . . . . . 58
System Validation and Reconfiguration Procedures After Hardware Upgrade from rp34x0 . . . . . . . . 59
2. RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal and External RAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Cabling Kit and Cabling Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing RAID for Simplex Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Smart Array RAID for Duplex Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up a Smart Array RAID Card As a Boot Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Server for RAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
61
61
62
62
64
65
67
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3
Contents
4
Tables
Table 1-1. Upgrade Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1-2. Upgrade Kit Hardware Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1-3. Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1-4. Connector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-1. PCI Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-2. RAID Card Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
15
24
25
62
63
5
Tables
6
Figures
Figure 1-1. Release the Rack Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-2. Pedestal Mounted HP Integrity rx2600 or HP9000 rp34x0 Server . . . . . . . . . . . . . . . .
Figure 1-3. Removing the Top Metal Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-4. Front Bezel Retaining Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-5. Internal Physical Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-6. System Board Connectors and Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-7. Fan 1A or Fan 1B Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-8. Fan 2 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-9. Fan 3 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-10. Airflow Guides Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-11. Removing the Memory Airflow Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-12. Removing the Processor Airflow Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-13. Open the Release Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-14. Remove the Front Airflow Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-15. Processor Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-16. Disconnect Power Pod Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-17. Remove Power Pod Mounting Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-18. Disconnect Power Pod from Processor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-19. Remove Power Pod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-20. Disconnect the Turbo Fan Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-21. Release Heatsink Captive Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-22. Slide Sequencing Retainer Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-23. Unlock Processor Module Locking Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-24. Remove Processor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-25. Removing the iLO Manageability Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-26. Removing the PCI Card Cage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-27. VGA and DB9 Mechanical Cover Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-28. Remove System Board Mounting Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-29. Remove the System Board Mounting Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-30. Remove the System Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-31. Rear Chassis with Port Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-32. Rear Chassis with Port Label Removed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-33. Slide System Board into Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-34. Align the System Board PCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-35. Slide System Board in Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-36. Install the Rear Panel Mounting Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-37. Aligning the Processor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-38. Locking the Processor Module in Place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-39. Slide the Sequencing Retainer Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-40. Secure the Captive Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-41. Aligning the Processor Module Power Pod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-42. Install the Processor Module Power Pod Mounting Screws. . . . . . . . . . . . . . . . . . . . .
Figure 1-43. Connect the Turbo Fan Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
22
23
23
24
25
26
26
27
27
28
28
29
30
31
32
32
33
34
34
35
35
36
37
38
39
40
40
41
41
42
42
43
44
44
45
46
47
47
48
48
49
49
7
Figures
Figure 1-44. Connecting the Power Pod Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-45. Reinstall the Power Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-46. Inserting DIMM into Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-47. Airflow Guides Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-48. Installing the Front Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-49. Aligning the Top Metal Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1-50. Closing the Top Metal Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-1. Smart Array 6402 RAID Card (SA 6404 RAID Card not shown) . . . . . . . . . . . . . . . . .
8
50
51
53
53
56
57
57
63
Preface
This preface contains the following sections:
•
Intended Audience
•
What’s New?
•
Notational Conventions
•
Reader Comments and Feedback
•
Related Information
•
Printing History
Intended Audience
This document is intended to provide technical product and support information for authorized service
providers, customer system administrators, and HP support personnel.
What’s New?
•
The layout of this document was changed to improve usability
•
Added 4 GB DIMM information
•
Added RAID card information
Notational Conventions
The following notational conventions are used in this publication.
WARNING
A warning lists requirements that you must meet to avoid personal injury.
CAUTION
A caution provides information required to avoid losing data or avoid losing system
functionality.
NOTE
A note highlights useful information such as restrictions, recommendations, or important
details about HP product features.
•
Commands and options are represented using this font.
•
Text that you type exactly as shown is represented using this font.
•
Text to be replaced with text that you supply is represented using this font.
Example:
“Enter the ls -l filename command” means you must replace filename with your own text.
•
Keyboard keys and graphical interface items (such as buttons, tabs, and menu items) are represented using this
font.
Examples:
The Control key, the OK button, the General tab, the Options menu.
9
•
Menu —> Submenu represents a menu selection you can perform.
Example:
“Select the Partition —> Create Partition action” means you must select the Create Partition menu item from
the Partition menu.
•
Example screen output is represented using this font.
Reader Comments and Feedback
HP welcomes your feedback on this publication. Please address your comments to
edit@presskit.rsn.hp.com and note that you will not receive an immediate reply. All comments are
appreciated.
Related Information
You can find other information on HP server hardware management, Microsoft® Windows®, and diagnostic
support tools in the following publications.
Web Site for HP Technical Documentation:
http://docs.hp.com
The main Web site for HP technical documentation is http://docs.hp.com, which has complete information
available for free.
Server Hardware Information:
http://docs.hp.com/hpux/hw/
The http://docs.hp.com/hpux/hw/ Web site is the systems hardware portion of the docs.hp.com and
provides HP nPartition server hardware management details, including site preparation, installation, and
more.
Windows Operating System Information
You can find information about administration of the Microsoft® Windows® operating system at the following
Web sites, among others:
•
http://docs.hp.com/windows_nt/
•
http://www.microsoft.com/technet/
Diagnostics and Event Monitoring: Hardware Support Tools
Complete information about HP’s hardware support tools, including online and offline diagnostics and event
monitoring tools, is at the http://docs.hp.com/hpux/diag/ Web site. This site has manuals, tutorials,
FAQs, and other reference material.
Web Site for HP Technical Support:
http://us-support2.external.hp.com
HP’s IT resource center Web site at http://us-support2.external.hp.com/ provides comprehensive
support information for IT professionals on a wide variety of topics, including software, hardware, and
networking.
Books about HP-UX Published by Prentice Hall
The http://www.hp.com/hpbooks/ Web site lists the HP books that Prentice Hall currently publishes, such
as HP-UX books including:
10
•
HP-UX 11i System Administration Handbook
http://www.hp.com/hpbooks/prentice/ptr_0130600814.html
•
HP-UX Virtual Partitions
http://www.hp.com/hpbooks/prentice/ptr_0130352128.html
HP Books are available worldwide through bookstores, online booksellers, and office and computer stores.
Printing History
The Printing History below identifies the edition dates of this manual. Updates are made to this publication
on an unscheduled, as needed, basis. The updates will consist of a complete replacement manual and
pertinent on-line or CD-ROM documentation.
First Edition
........................................................
December 2004
Second Edition
........................................................
June 2005
11
12
1 HP Integrity rx2620 Upgrade
Introduction
This hardware upgrade guide lists the required components and provides the instructions for converting an
HP Integrity rx2600 server or HP 9000 rp34x0 server to an HP Integrity rx2620 server.
The upgrade guide is organized into the following sections:
•
“Introduction”
•
“Upgrade Checklist”
•
“Upgrade Kit Contents”
•
“Safety and Environmental Considerations”
•
“Upgrade Preparation and System Shutdown”
•
“System Hardware Component Upgrade Instructions”
•
“System Validation and Reconfiguration Procedures After Hardware Upgrade from rx2600”
•
“System Validation and Reconfiguration Procedures After Hardware Upgrade from rp34x0”
Time Required
Upgrading your HP Integrity rx2600 server or HP 9000 rp34x0 server to an HP Integrity rx2620 server may
require several hours, depending on preparatory time, but you should plan for one hour of system downtime.
Preparatory time includes checking the upgrade kit, preparing an ESD-safe work station, and backing up
your data.
Upgrade Assistance
Several system components must be removed, upgraded and reinstalled to successfully complete this
upgrade. Review the entire guide before attempting this upgrade to ensure you can complete the procedure
yourself. Contact your local HP support representative for upgrade assistance.
Chapter 1
13
HP Integrity rx2620 Upgrade
Upgrade Checklist
Upgrade Checklist
Use the following checklist to assist in completing your upgrade from an HP Integrity rx2600 server or HP
9000 rp34x0 server to an HP Integrity rx2620 server.
Table 1-1
Upgrade Checklist
Step
Procedure
1
Verify Upgrade Kit Contents (page 15)
2
Upgrade preparation
3
Shutting down the system
4
Hardware component upgrades
Completed
a. System board
b. CPU(s)
c. CPU Fans
5
Validate system upgrade
a. Powering on the System
b. Restoring the product, serial and UUID numbers
14
Chapter 1
HP Integrity rx2620 Upgrade
Upgrade Kit Contents
Upgrade Kit Contents
The following items comprise the contents of the upgrade kit. The hardware components listed under the
“Additional Upgrade Components Required” list are also required for the upgrade, but must be ordered
separately. Verify the contents of the upgrade kit against the packing list. Resolve any discrepancies before
continuing.
Table 1-2
Upgrade Kit Hardware Contents
Part No.
Description
Qty
AB331-67001
System Board
1
AB331-04001
CPU Fans
2
AB331-40001
Nameplate, Integrity rx2620 (Rack)
1
AB331-40002
Nameplate, Integrity rx2620 (Tower)
1
AB331-10001
Documentation CD-ROM
1
5021-1184
Read Me First
1
7121-8194
Intel® Itanium® 2 Rack Label
1
AB359-84001
UUID Upgrade Label (only used if upgrading from
rp34xx server)
1
5971-4257
Media, CD-ROM, Offline Diagnostics
1
5182-4257
Upgrade Returns Instruction Packet
1
Qty
Rcvd
Additional Upgrade Components Required
AB334A, AB335A
or AB336A
Chapter 1
CPU
(Cannot mix CPU types within the same server.)
1 min; 2 max
15
HP Integrity rx2620 Upgrade
Service Tools Required
Service Tools Required
Service of this product may require one or more of the following tools:
•
IPF CPU Install Tool Kit (P/N 5069-5441), consisting of:
•
Disposable ESD Kit
•
Label-less CPU install tool (2.5mm hex and Torx 15)
•
1/4 inch Flat Blade Screwdriver
•
Phillips No. 1 Screwdriver
•
ACX-10 Torx Screwdriver
•
ACX-15 Torx Screwdriver
•
ACX-25 Torx Screwdriver
16
Chapter 1
HP Integrity rx2620 Upgrade
Safety and Environmental Considerations
Safety and Environmental Considerations
WARNING
Voltages are present at various locations within the server whenever an AC power
source is connected. This voltage is present even when the main power switch is in
the off position.
Ensure that the system is powered-down and all power sources have been
disconnected from the server prior to attempting the following procedures.
Failure to observe this warning could result in personal injury or damage to
equipment.
Communications Interference
HP system compliance tests are conducted with HP supported peripheral devices and shielded cables, such as
those received with the system. The system meets interference requirements of all countries in which it is
sold. These requirements provide reasonable protection against interference with radio and television
communications.
Installing and using the system in strict accordance with HP's instructions minimizes the chances that the
system will cause radio or television interference. However, HP does not guarantee that the system will not
interfere with radio and television reception.
Take these precautions:
•
Use only shielded cables.
•
Install and route the cables per the instructions provided.
•
Ensure that all cable connector screws are firmly tightened.
•
Use only HP supported peripheral devices.
•
Ensure that all panels and cover plates are in place and secure before system operation.
Electrostatic Discharge
HP systems and peripherals contain assemblies and components that are sensitive to electrostatic discharge
(ESD). Carefully observe the precautions and recommended procedures in this manual to prevent component
damage from static electricity.
WARNING
Connect to ground with a wrist strap. Connection can be made to any grounded
metal assembly in the cabinet. Both you and the electronic devices must be
grounded to avoid static discharges that can cause damage.
Take these precautions:
•
Prepare an ESD safe work surface large enough to accommodate the various assemblies handled during
the upgrade. Use a grounding mat and an anti-static wrist strap, such as those included in the ESD Field
Service Kit (A3024-80004).
•
The anti-static bag can not function as a static dissipating mat. Do not use the anti-static bag for any
other purpose than to enclose a product.
Chapter 1
17
HP Integrity rx2620 Upgrade
Upgrade Preparation and System Shutdown
•
Treat all assemblies, components, and interface connections as static-sensitive.
•
When unpacking cards, interfaces, and other accessories that are packaged separately from the system,
keep the accessories in their conductive plastic bags, until they are ready to be installed.
•
Avoid working in carpeted areas, and keep body movement to a minimum while installing accessories.
Upgrade Preparation and System Shutdown
In general, your system should be stable before beginning the upgrade procedure. In addition, perform the
following actions before you begin your server upgrade:
•
Verify the system meets minimum software and firmware requirements
•
Update system firmware and software if required
•
Back up your system
•
Shut down the system
Firmware Requirements
Ensure the server meets the minimum firmware revisions listed below. Update as necessary.
•
Management Processor (MP) firmware E.03.13 (if upgrading from MP firmware version E.02.23, then you
need to upgrade to version E.02.29, then upgrade to version E.03.13)
•
VGA/Bus card ROM Firmware:
ECI Rev. A: Revision yi000018.001 or higher
ECI Rev. B: Revision yi004325.001 or higher
Software Requirements
Ensure the server meets the minimum software revisions listed below. Update as necessary.
•
IPF Offline Diagnostics 0412, December 2004
Minimum Operating System Requirements
•
HP-UX 11i v2
•
MicroSoft Windows Server 2003, Enterprise Edition for 64 bit Itanium 2 Systems
•
Red Hat Linux Advanced Server 3
•
SUSE Linux Enterprise Server 9
•
OpenVMS I64 Version 8.2
18
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
LAN Requirements
The LAN paths for the right and left LAN ports on the rear panel will change as a result of installing this
upgrade. Refer to your OS manual to modify your LAN configuration.
HP Integrity rx2600 LAN path configuration before upgrade:
LAN 10/100 (right) –
0/0/3/0
0x00306E38594B
0
UP
lan0
snap0
1
ETHER Yes
119
LAN 10/100/1000 (left) – 0/1/2/0
0x00306E38D9B9
1
UP
lan1
snap1
2
ETHER Yes
119
HP Integrity rx2620 LAN path configuration after upgrade:
LAN 10/100/1000 (right) – 0/1/2/0
0x000E7F7E101C
1
UP
lan1 snap1
1
ETHER Yes
119
LAN 10/100/1000 (left) –
0x000E7F7E101D
2
UP
lan2 snap2
2
ETHER Yes
119
NOTE
0/1/2/1
Use the appropriate operating system tool (for example, ifconfig for HP-UX) to validate your
LAN configuration.
Back Up Your System
Before performing the server upgrade, protect yourself by backing up all data and your server OS. In the
event of interruptions (for example power failure or interference), it may be necessary to resume operation in
the old configuration before upgrading the server.
Back Up Your Data
Back up your data in accordance with local procedures.
Back Up the Operating System
Always keep a backup copy of the current operating system (OS) available for emergency use. The OS was
provided on CD with your server.
System Shutdown
Step 1. Press the power switch on the server front panel. Verify that the power LED goes off.
Step 2. Disconnect the AC power cords from the server rear panel.
System Hardware Component Upgrade Instructions
This section contains detailed instructions for upgrading the rx2600 or rp34x0 to an rx2620 using the
following procedure:
Step 1. Remove system top metal cover and bezel.
Step 2. Remove system fans, PCI card cage, airflow guides, memory, processors, management processor
and system board.
Step 3. Upgrade system board.
Chapter 1
19
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 4. Upgrade processors.
Step 5. Reinstall system fans 2 and 3, PCI card cage, airflow guides, memory, and management processor.
Step 6. Upgrade system fans 1A and 1B.
Step 7. Install HP Integrity rx2620 name plate.
Step 8. Affix Itanium 2 label to rack (rp34x0 upgrade only).
Step 9. Apply UUID label to pull tab (rp34x0 upgrade only).
Step 10. Replace system top metal cover and bezel.
Step 11. Perform system validation and reconfiguration procedures after hardware upgrade (rx2600 and
rp34x0 specific instructions).
Removing System Top Metal Cover and Bezel
To upgrade, remove, or replace most system components, you must first remove the top metal cover from the
system chassis. This section explains how to remove the cover for both the rackmount and pedestal
configurations.
WARNING
Do not remove the system cover(s) without first turning the system off and
unplugging the power cord from the outlet or power protection device unless you
are only replacing a hot-swappable fan. Always replace the cover(s) before turning
the system on.
Accessing a Rack Mounted Server
The HP Integrity rx2620 server is designed to be rack mounted. The following procedure explains how to gain
access to an HP Integrity rx26xx or rp34xx server that is mounted in an approved rack.
WARNING
Ensure that all anti-tip features (front and rear anti-tip feet installed; adequate
ballast properly placed, etc.) are employed prior to extending the server.
Extending the Server from the Rack
NOTE
Ensure that there is enough area (approximately 1.5 meters (4.5 ft.) to fully extend the server
out the front of the rack and work on it.
To extend the server from the rack, perform the following steps:
Step 1. Remove the T-25 screws that fasten the server to the rack.
Step 2. Release the rack latches by rotating them outward.
20
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-1 Release the Rack Latches
Front of Chassis
Step 3. Slide the system out of the rack until the guide-rail release clips are visible.
Accessing an rx2600 or rp34x0 Pedestal Mounted Server
The HP Integrity rx2600 and HP 9000 rp34x0 servers are also designed to be pedestal mounted. You do not
need to remove the pedestal from the HP server to gain access to internal components. The front bezel, front
cover, and top cover may be removed with the pedestal attached to the HP server.
Chapter 1
21
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-2
22
Pedestal Mounted HP Integrity rx2600 or HP9000 rp34x0 Server
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Removing the Top Metal Cover
Step 1. Ensure the top metal cover lock keyswitch is in the unlocked position. Rotate the blue release lever
toward the back of the system and slide the cover toward the back of the system.
Figure 1-3 Removing the Top Metal Cover
Front of Chassis
Step 2. Lift the top metal cover off the system chassis.
Removing the Front Bezel
You must remove the front bezel from the chassis to replace the system name plate.
Step 1. Press in on the retaining clips located on the right-side of the front panel.
Figure 1-4 Front Bezel Retaining Clip
Front of Chassis
Step 2. Rotate the front panel outward and lift it away from the system chassis.
Chapter 1
23
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Removing System Fans, PCI Card Cage, Airflow Guides, Memory, Processors, and
the Management Processor
Location of Internal Components and Connectors
Figure 1-5
Internal Physical Layout
2
1
3
Pwr 2
Pwr 1
14
4
Fan 1B
Fan 1A
13
5
12
11
Fan 3
PS 1
Fan 2
6
7
10
9
Table 1-3
PS 2
Drive 2
Front of Chassis
Drive 1
Drive 0
8
Component Locations
1 Power receptacles (PWR1 right, PWR2 left)
8 Hot-pluggable hard drives (up to 3)
2 Memory Airflow guide
9 Hard disk lock
3 Processor Airflow guide
10 System fans (Fan 2 - center, Fan 3 - I/O cage)
4 System fans (Fan 1A - right, Fan 1B - left)
11 Intrusion switch
5 Slimline optical drive
12 Memory sockets
6 Power supplies (PSU1 center, PSU2 under optical
drive)
13 PCI card cage
7 Status panel board
14 Management controller (Optional)
24
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-6
System Board Connectors and Slots
19
18
21
20
1
2
SCSI CH A
SCSI CH B
17
3
4
16
5
15
6
14
13
Table 1-4
12 11
10
9
8
7
Front of Chassis
Connector Locations
1 External SCSI Connector
9 Power Module Power Connector
17 iLO Manageability Card
connector
2 SCSI Connectors A & B
10 Memory Sockets
18 Serial Ports (2)
3 CPU Power Pods
11 Status Panel Connector
19 USB Connectors
4 CPU1
12 Power Module Auxiliary
Connector
20 LAN Connector
5 CPU0
13 SCSI Backplane Power
Connector
21 LAN Connector (rx26xx
only)
6 Turbo Fan Power Connectors
14 PCI/Memory Fan Cable
Connector
7 Battery
15 PCI Backplane Connector
8 PS Fan Connectors
16 IDE Drive Connector
Chapter 1
25
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Removing System Fans
Step 1. To remove fans 1A, 1B, 2 and 3 from the system, grasp the appropriate fan and lift it out of the fan
socket.
Figure 1-7 Fan 1A or Fan 1B Removal
Fan 1A
Fan 1B
Front of Chassis
Figure 1-8 Fan 2 Removal
Fan 2
Front of Chassis
26
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-9 Fan 3 Removal
Fan 3
Front of Chassis
Removing Airflow Guides
The system has the following airflow guides:
Figure 1-10
Airflow Guides Locations
Processor Airflow Guide
Memory Airflow Guide
Front of Chassis
Removing the Memory Airflow Guide
Step 1. Grasp the memory airflow guide and lift it out of the system.
Chapter 1
27
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-11 Removing the Memory Airflow Guide
Front of Chassis
Removing the Processor Airflow Guide
Step 1. Remove the IDE cable and power module cables from the processor airflow guide cable clips.
Step 2. Remove the main portion of the airflow guide:
a. Hold the guide using the opening on top of the guide.
b. At the same time, grasp the back end of the airflow guide and lift the guide out of the system.
Figure 1-12 Removing the Processor Airflow Guide
Front of Chassis
28
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 3. Remove the front portion of the airflow guide:
a. Rotate the clip clockwise to release the latch.
Figure 1-13 Open the Release Clip
Front of Chassis
Step 4. Disconnect the power cable connected to the guide from the system board.
Step 5. Lift the front portion of the airflow guide out of the system.
Chapter 1
29
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-14 Remove the Front Airflow Guide
Front of Chassis
Removing System Memory
Next, remove all system memory by performing the following steps:
Step 1. Push the appropriate extraction levers found on either side of the DIMM slot outward to the open
position. The DIMM will eject from the slot.
Step 2. Remove the DIMM from the socket and store it in a static-free container.
30
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Removing Processor Modules
Figure 1-15
Processor Location
Power Pod
CPU 0
Power Pod
CPU 1
CPU 1
CPU 0
Front of Chassis
Chapter 1
31
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 1. Disconnect the power pod cable from the power connector on the system board.
Figure 1-16 Disconnect Power Pod Cable
Front of Chassis
Step 2. Remove the two power pod mounting screws.
Figure 1-17 Remove Power Pod Mounting Screws
Front of Chassis
32
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 3. Slide the power pod toward the rear of the system board disconnecting the power pod from the
processor module.
Figure 1-18 Disconnect Power Pod from Processor Module
Front of Chassis
Step 4. Lift the power pod up and out of the chassis. Place the power pod into an anti-static container.
Chapter 1
33
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-19 Remove Power Pod
Front of Chassis
Step 5. Disconnect the processor module turbo fan power cable.
Figure 1-20 Disconnect the Turbo Fan Cable
Front of Chassis
34
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 6. Release the four heatsink captive screws on the processor module heat sink.
Figure 1-21 Release Heatsink Captive Screws
Front of Chassis
Step 7. Slide the sequencing retainer plate toward the back of the system to open the hole in the edge of the
heatsink for insertion of the special processor tool into the processor module locking mechanism.
Figure 1-22 Slide Sequencing Retainer Plate
Front of Chassis
Chapter 1
35
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 8. Unlock the processor-locking mechanism using the special processor tool (P/N 5069-5441), or
equivalent 2.5 mm hex tool, shipped with your replacement processor assembly. Insert the tool into
the lock and rotate the special processor tool 180 degrees counterclockwise. Verify that the
processor-locking mechanism is rotated into the unlocked position.
WARNING
The zero insertion force (ZIF) socket for the processor is locked and
unlocked by 1/2 of a full turn of the 2.5 mm hex tool. The counterclockwise
180 degree rotation (1/2 turn) unlocks the socket. A clockwise 180 degree
rotation locks the socket. Attempting to turn the locking mechanism more
that 180 degrees can severely damage the socket.
Figure 1-23 Unlock Processor Module Locking Mechanism
Unlocked
Locked
Front of Chassis
36
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 9. Lift the processor module and the turbo fan assembly up and out of the chassis. Place the processor
module into an anti-static container.
WARNING
Carefully handle the CPU to avoid damaging the pins. If possible, cover the
exposed CPU pins with a pin cover.
Figure 1-24 Remove Processor Module
Front of Chassis
Chapter 1
37
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Removing the iLO Manageability Card
Step 1. Unscrew the two mounting screws that connect the iLO Manageability card to the internal chassis
post and the two external mounting screws that are located on both sides of the 25-pin serial
connector.
Figure 1-25 Removing the iLO Manageability Card
Rear of Chassis
iLO Manageability Card
Step 2. Disconnect the iLO Manageability card connector.
Step 3. Remove the iLO Manageability card from the system by grasping it by its edges.
38
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Removing the PCI Card Cage
To remove the PCI cage from the server, perform the following steps:
Step 1. Lift up on the PCI card cage release lever and the back edge of the PCI card cage and lift the PCI
card cage out of the system.
Figure 1-26 Removing the PCI Card Cage
Front of Chassis
Removing the System Board
Step 1. Remove the power connector plate.
a. Unscrew the two power connector mounting screws on the back of the system.
b. Reach inside the system to remove the power connectors from the socket. The power connectors
will still be connected to their cables.
Step 2. Remove the VGA port mechanical cover located on the right side of the rear of the chassis (if
necessary). See Figure 1-27 for the location of the cover.
Step 3. Remove the DB9 port mechanical cover located on the MP area of the rear of the chassis (if
necessary). See Figure 1-27 for the location of the cover.
Chapter 1
39
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-27 VGA and DB9 Mechanical Cover Locations
VGA cover
DB9 cover
Rear of chassis
Step 4. Unscrew the six backplane system board mounting screws that connect the system board to the
rear of the system chassis.
Figure 1-28 Remove System Board Mounting Screws
Rear of chassis
Step 5. Disconnect all cables that are connected to the system board. To help with re-assembly, make note
of which cables were connected to which connector.
NOTE
To access the three power cables near the PCI cage, you must lift up the connector
bridge for the PCI cage fan.
Step 6. Unscrew the system board mounting screw. A screw symbol is adjacent to the mounting screw.
40
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-29 Remove the System Board Mounting Screw
Front of Chassis
Step 7. Remove the system board:
a. Grasp the memory controller chip heatsink and slide the system board toward the front of the
system. This releases the system board from its chassis standoffs.
b. Lift up the processor module side of the system board and slide it free of the PCI cage bay.
Figure 1-30 Remove the System Board
Front of Chassis
Remove Rear Chassis Port Label (rp34x0)
NOTE
Chapter 1
This procedure applies only to an upgrade from an rp34x0 machine.
41
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
In rp34x0 machines, the VGA and secondary LAN ports are not functional. A label on the rear of the rp34x0
chassis designates the VGA port as Not Available and covers the secondary LAN port. Before the system
board is upgraded, the label must be removed. The following figures show the rear chassis with and without
the port label.
Figure 1-31
Rear Chassis with Port Label
Figure 1-32
Rear Chassis with Port Label Removed
Upgrading the System Board
Installing the New System Board
Step 1. Verify the part number of the system board (AB331-67001).
Step 2. Grasp the new system board by its edges and carefully align it in the system:
42
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
a. Angle the board to allow the PCI connector to slide into the PCI cage bay area.
Figure 1-33 Slide System Board into Chassis
Front of Chassis
b. Align the system board keyholes with their standoffs on the chassis.
c. Slide the PCI connector posts on the system board into their slots on the system chassis.
Chapter 1
43
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-34 Align the System Board PCI Connector
Front of Chassis
Step 3. Slide the system board back toward the rear of the system to secure the system board on its
standoffs.
Figure 1-35 Slide System Board in Chassis
Front of Chassis
44
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Step 4. Screw in the system board mounting screw.
Step 5. Connect all cables to their appropriate connectors on the system board.
Step 6. Screw in the six rear backplane system board mounting screws.
Figure 1-36 Install the Rear Panel Mounting Screws
Rear of Chassis
Chapter 1
45
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Upgrading the CPUs
Installing the New Processor Module
Step 1. Verify part number of the CPU (AB334A, AB335A or AB336A).
NOTE
Ensure that each processor has an identical part number when installing more than
one processor. CPU types cannot be mixed within the same server.
Step 2. Ensure that socket covers are removed and that sockets are in the unlocked position. See
“Removing Processor Modules” on page 31 for more detail.
Step 3. Use the four locator posts on the heatsink and the turbo fan power cable to properly align the fan
and processor module on the system board. The four locator posts will fit in locator holes on the
system board processor module mount. The turbo fan power cable must be positioned so that it is
located on the side of the heatsink that faces the front of the system.
Figure 1-37 Aligning the Processor Module
Front of Chassis
CAUTION
Do not press the processor module into the socket. When properly aligned, the
processor pins will seat into the ZIF socket, no additional pressure is required.
Step 4. Use the special processor tool shipped with your processor module to lock the processor module in
place on the system board. To do this, insert the special processor tool into the hole that runs down
the side of the heatsink and rotate it clockwise 180 degrees.
46
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-38 Locking the Processor Module in Place
Unlocked
Locked
Front of Chassis
Step 5. Slide the sequencing retainer plate toward the rear of the system.
Figure 1-39 Slide the Sequencing Retainer Plate
Front of Chassis
Step 6. Screw in the four heatsink captive screws.
Chapter 1
47
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-40 Secure the Captive Screws
Torquing pattern
1
4
3
2
4
1
2
3
Front of Chassis
Step 7. Slide the power module on the system board metal mounting bracket so that the power module
connector connects with its connector on the processor module.
Figure 1-41 Aligning the Processor Module Power Pod
Front of Chassis
Step 8. Align the two mounting screw holes on the power module with their screw holes on the system
board’s metal mounting bracket. Screw in the power module mounting screws.
48
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-42 Install the Processor Module Power Pod Mounting Screws
Front of Chassis
Step 9. Connect the processor module turbo fan power cable to the connector on the system board.
Figure 1-43 Connect the Turbo Fan Cable
Front of Chassis
Step 10. Connect the power pod cable to the power connector on the system board.
Chapter 1
49
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-44 Connecting the Power Pod Cable
Front of Chassis
Reinstalling System Fans, PCI Card Cage, Airflow Guides, Memory, and the
Management Processor
Reinstall the Management Processor
Connect SCSI cables before replacing the Management Processor.
NOTE
Step 1. Insert the management processor in the system.
Step 2. Grasp its edges and place it on the two management processor posts.
Step 3. Push the 10/100 management LAN, 15-pin VGA and 25-pin serial connectors through their
openings on the back of the system
Step 4. Connect the management processor:
•
Connect the management processor cable to its connector on the system board.
•
Screw in the two mounting screws that connect the management processor to the internal
chassis post.
•
Screw in the two external mounting screws that are located on both sides of the 25-pin serial
connector.
Step 5. Replace the power connectors in their slots on the back of the system and screw in the power
connector mounting screws.
50
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-45 Reinstall the Power Connectors
Front of Chassis
Chapter 1
51
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Reinstalling System Memory
Memory modules must be loaded in the correct order:
•
In the HP Integrity rx2620 server, DIMMs must be installed in matched quads. Two matched memory
card pairs of equal size (that is, four identical DIMMs) must be installed, one pair per memory cell, as
listed below:
— 0A, 0B and 1A, 1B must be matched pairs of equal size
— 2A, 2B and 3A, 3B must be matched pairs of equal size
— 4A, 4B and 5A, 5B must be matched pairs of equal size
NOTE
If upgrading to 4 GB DIMMs, the only configuration supported is to install 8 4 GB DIMMs in
the first eight slots (0A, 0B, 1A, 1B, 2A, 2B, 3A, and 3B). the four remaining slots (4A, 4B, 5A
and 5B must remain empty.
The system firmware required for 4 GB DIMM operation is 3.17 or later.
DIMMs match if they have the same HP part number. The DIMMs are 184-pin,
industry-standard, DDR266, CL2, registered ECC modules. Industry standard means the
DIMMs meet specifications detailed in the JDEC Standard No. 21-C, Module 4, titled “PC2100
and PC1600 DDR SDRAM Registered DIMM Design Specification.” A complete and current list
of acceptable DIMMs is provided on the parts website at: http://partsurfer.hp.com.
To reinstall the original DIMMs into the new system board, perform the following steps:
NOTE
Insert memory in the new system board in the same locations as they were in the old system
board.
Step 1. Holding the memory module by its left and right edges, insert the module into the slot.
The memory modules are keyed and can only be inserted in one direction. When the module is
correctly seated, the retainer clips will return to their fully upright position. Snap the clips firmly
into place to ensure that the DIMMs are seated properly.
Step 2. Gently and evenly push on each side of the DIMM until it seats in the slot. Ensure the extraction
levers are in the closed position.
52
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-46
Inserting DIMM into Slot
Reinstalling Air Flow Guides
Figure 1-47
Airflow Guides Locations
Processor Airflow Guide
Memory Airflow Guide
Front of Chassis
Reinstalling the Memory Airflow Guide
Step 1. Align the guides on both sides of the original airflow guide with the slots on the chassis.
Step 2. Insert the memory airflow guide in the slots.
Reinstalling the Processor Airflow Guide and Upgrading the CPU Fans (1A and 1B)
Step 1. Reinstall the front portion of the original airflow guide:
a. Align the release latch of the front half of the airflow guide over the release latch post and snap
it in place.
Chapter 1
53
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
b. Connect power connector on the front portion of the guide to the connector on the system board.
Step 2. Reinstall the main portion of the original airflow guide:
a. Hold the opening on top of the processor airflow guide.
b. At the same time, grasp the back end of the airflow guide and insert the airflow guide into the
system.
c. Connect the power module cable and place the power and IDE cables in the cable clips.
54
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Reinstalling PCI Card Cage
To reinstall the original PCI cage, perform the following action:
Step 1. Insert the PCI card cage into the system and engage the release lever.
Reinstalling System Fans 2 and 3
NOTE
System fans 1A and 1B must be upgraded. See “Upgrade CPU Fans (1A and 1B)”.
Step 1. Grasp the fan module and insert it into its fan socket.
Step 2. Check for proper seating of the fan in its socket.
Upgrade CPU Fans (1A and 1B)
Step 1. Verify that fans 1A and 1B (AB331-04001) are those provided with the upgrade kit before
installation.
Step 2. Grasp the fan module and insert it into its fan socket.
Step 3. Check for proper seating of the fan in its socket.
Step 4. Insert the two airflow guide retaining tabs into the two slots on the front half of the airflow guide.
Installing HP Integrity rx2620 Name Plate and Intel Itanium 2 Rack Label
To install the HP Integrity rx2620 server name plate and Intel Itanium 2 rack label, follow these steps:
Step 1. Locate the name plate release prongs on the back side of the system bezel.
Step 2. Exert outward pressure on the prongs until the name plate releases through the front of the bezel.
Step 3. Push on the new name plate through the front of the bezel until it snaps into place.
Step 4. If upgrading from rp34x0, affix Intel Itanium 2 label to outside of rack and adjacent to the server.
Apply UUID Label (rp34x0)
When upgrading from an rp34x0, apply the UUID label to the rear of the pull tab located in the slot between
the power supply and disk drives.
NOTE
Chapter 1
The UUID label is not used when upgrading from an rx2600 and should be discarded.
55
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Replacing the Front Bezel and Top Metal Cover
Replacing the Front Bezel
To install the front bezel, perform the following step:
Step 1. Push the front bezel straight into the chassis until it snaps into place.
Figure 1-48 Installing the Front Bezel
Replacing the Top Metal Cover
CAUTION
Secure any wires or cables in your system so they will not get cut or interfere with the
replacement of the cover.
Step 1. Align the front edge of the top metal cover with the alignment mark on the optical drive bay.
56
Chapter 1
HP Integrity rx2620 Upgrade
System Hardware Component Upgrade Instructions
Figure 1-49 Aligning the Top Metal Cover
To replace cover,
align front edge here
then slide forward
Front of Chassis
Step 2. Grasp the blue release lever and slide the top metal cover toward the front of the system until the
lever snaps into place.
Figure 1-50 Closing the Top Metal Cover
Front of Chassis
Step 3. Slide the system into the rack enclosure and reconnect the power cables.
Chapter 1
57
HP Integrity rx2620 Upgrade
System Validation and Reconfiguration Procedures After Hardware Upgrade from rx2600
System Validation and Reconfiguration Procedures After Hardware
Upgrade from rx2600
The system board upgrade part is configured at the factory with default product, serial and UUID IDs. After
replacing the system board, factory default ID values must be overwritten with actual system values. In
rx2600 machines, the product, serial and UUID actual ID values are stored in both the system and display
boards. Product, serial and UUID IDs can be automatically copied from the display board to overwrite the
default factory ID values on the new system board.
Step 1. Power on the system.
a. Reconnect AC power to rear panel connectors.
b. Press the front panel power switch to power on the server.
Step 2. Restore the product, serial and UUID IDs.
a. Answer Yes to the copy prompt displayed during system power on.
b. Reboot the server.
Step 3. Boot the machine to EFI.
Step 4. Verify system board installation.
a. Enter the info sys command. Verify that the newly installed system board is recognized by the
system. Below is an example of the info sys command output following a successful upgrade:
NOTE
The product number is now rx2620 and the product, serial and UUID number
values are populated.
SYSTEM INFORMATION
Date/Time: Aug 3, 2004 15:34:26 (20:04:08:03:15:34:26)
Manufacturer: hp
Product Name: server rx2620
Product Number: AB459A
Serial Number: SGH4414201
UUID: 162D4BA1-4D67-11D8-881B-E20562B8C81F
System Bus Frequency: 199 MHz
Step 5. Verify CPU installation.
a. Enter the info cpu command. Verify that all newly installed processors are recognized by the
system. Below is an example of the info cpu command output following a successful upgrade:
NOTE
One processor is installed in the example below.
PROCESSOR MODULE INFORMATION
# of
CPU
Logical
Module CPUs
Speed
------ ------- -------0
1
1.3 GHz
L3
Cache
Size
-----3 MB
L4
Cache
Size
-----None
Family/
Model
Processor
(hex.)
Rev State
------- --- -----------1F/02
A1
Active
Step 6. Check the system event log for erroneous system events and run system diagnostics as necessary.
Step 7. Boot the operating system.
58
Chapter 1
HP Integrity rx2620 Upgrade
System Validation and Reconfiguration Procedures After Hardware Upgrade from rp34x0
System Validation and Reconfiguration Procedures After Hardware
Upgrade from rp34x0
The system board upgrade part is configured at the factory with default product, serial and UUID IDs. After
replacing the system board, factory default ID values must be overwritten with actual system values. In
rp34x0 machines, the product, serial and UUID actual IDs must be entered manually.
Step 1. Power on the system.
a. Reconnect AC power to rear panel connectors.
b. Press the front panel power switch to power on the server.
Step 2. Restore product, serial and UUID IDs.
a. Type y when prompted to change the system IDs.
Do you want to set the system IDs (can be set at the shell using: sysset)?
(y/[n])
b. Slide the pull tab out of its location in the slot between the power supply and disk drives.
c. Enter UUID, product and serial ID values located on the pull tab label.
Please enter UUID (. to abort)
UUID: 162D4BA1-4D67-11D8-881B-E20562B8C81F
Please enter product number (. to abort)
Product Number: AB459A
Please enter serial number (. to abort)
Serial Number: SGH4414201
d. Type y when prompted to set the system IDs to listed values.
NOTE
Ensure system ID values listed on the screen output match values on the pull
tab.
The system IDs will be set to the following values:
UUID: 162D4BA1-4D67-11D8-881B-E20562B8C81F
Product Number: AB459A
Serial Number: SGH4414201
Set the system IDs to the above values?
(y/n)
e. Verify successful system ID restoration.
New system ID values were set successfully.
2 0 0x0002F2 0x0000000000000000 Set system IDs to valid values
0 0 0x0002B9 0x0000000000000013 EFI POST code
Step 3. Boot the machine to EFI.
Step 4. Verify system board installation.
a. Enter the info sys command. Verify that the newly installed system board is recognized by the
system. Below is an example of the info sys command output following a successful upgrade:
Chapter 1
59
HP Integrity rx2620 Upgrade
System Validation and Reconfiguration Procedures After Hardware Upgrade from rp34x0
NOTE
The product number is now rx2620 and the product, serial and UUID number
values are populated.
SYSTEM INFORMATION
Date/Time: Aug 3, 2004 15:34:26 (20:04:08:03:15:34:26)
Manufacturer: hp
Product Name: server rx2620
Product Number: AB459A
Serial Number: SGH4414201
UUID: 162D4BA1-4D67-11D8-881B-E20562B8C81F
System Bus Frequency: 199 MHz
Step 5. Verify CPU installation.
a. Enter the info cpu command. Verify that all newly installed processors are recognized by the
system. Below is an example of the info cpu command output following a successful upgrade:
NOTE
One processor is installed in the example below.
PROCESSOR MODULE INFORMATION
CPU
Module
-----0
# of
Logical
CPUs
------1
Speed
-------1.3 GHz
L3
Cache
Size
-----3 MB
L4
Cache
Size
-----None
Family/
Model
Processor
(hex.)
Rev State
------- --- -----------1F/02
A1
Active
Step 6. Check the system event log for erroneous system events and run system diagnostics as necessary.
Step 7. Reboot the server.
Step 8. Install the operating system using appropriate operating system documentation.
60
Chapter 1
2 RAID - Smart Array 6402 or 6404 Controller
for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
This section provides information and instructions for installing the HP A9890A PCI-X 2-Channel RAID SA
SCSI Controller (Smart Array 6402) or the HP A9891A PCI-X 4-Channel RAID SA SCSI Controller (Smart
Array 6404).
Before installing either Smart Array card, ensure the following hardware and software prerequisites are met:
•
Check the RAID-01 HP Smart Array Controller Driver Release Notes available at http://www.docs.hp.com
in the Networking & Communications section for known problems or other information needed for
installation.
•
Confirm that the Smart Array 6402 or 6404 controller and software are supported on the HP Integrity
server and I/O slot chosen. Refer to the Smart Array Controller Support Matrix located at
http://www.docs.hp.com in the Networking & Communications section for more information.
•
Check the HP Integrity server’s documentation to determine if additional tools are required for
component installation at http://www.docs.hp.com.
•
Smart Array 6402 or 6404 controller software media is available. It is included on CD or on the Web
through http://www.software.hp.com.
•
Confirm that HP-UX super-user privileges are available; they are necessary to complete the installation.
•
Confirm that the /usr/bin, /usr/sbin, and /sbin directories are in your PATH by logging in as root and
using the echo $PATH command.
CAUTION
Smart Array cards contain electronic components that can easily be damaged by small
amounts of electricity. To avoid damage, follow these guidelines:
•
Store controllers in their anti-static plastic bags until installation.
•
Work in a static-free area.
•
Handle controllers by the edges only. Do not touch electronic components or electrical
traces.
•
Use a grounding wrist strap.
•
Use a suitable ground—any exposed metal surface on the computer chassis.
Internal and External RAID
You can use RAID cards for internal and external connections:
•
Internal RAID refers to connecting embedded or internal disks to the RAID card
•
External RAID refers to connecting external devices to the RAID card
SCSI Cabling Kit and Cabling Guide
In addition to the Smart Array 6402 and 6404 RAID cards, you must also have the Internal Smart Array
Cable kit (HP P/N A9827A).
Chapter 2
61
RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
•
Cable A7231-63024 is used for the single channel or simplex RAID card
•
Cable A7231-63025 is used for the dual channel or duplex RAID card
Before installing the RAID card, refer to the Internal Cabling Guide for HP Smart Array Controllers HP P/N
5971-4280 available at http://www.docs.hp.com.
PCI Slots
Before inserting a RAID card, be certain of which PCI slots are available for RAID, and if the slot can be used
for internal or external RAID.
The following table lists the PCI slots and information about the RAID card that can be inserted into each
slot.
Table 2-1
PCI Slots
PCI Slot #
Description
1
Cannot be used with internal or external RAID.
2
Used only for external RAID 6402 or 6404.
3
Only slot that can be used for internal RAID 6402 or 6404. Can be
used for external RAID also.
4
Cannot be used with internal or external RAID.
IMPORTANT Do not use both the internal and external connectors on one port simultaneously. The card will
not function if both connectors on one port are used.
Installing RAID for Simplex Configuration
The RAID card comes pre-configured. You do not have to set any jumpers or connectors.
WARNING
Ensure that the system is powered down and all power sources have been
disconnected from the server prior to working with the server.
Voltages are present at various locations within the server whenever an AC power
source is connected. This voltage is present even when the main power switch is in
the off position.
Failure to observe this warning could result in personal injury or damage to
equipment.
Step 1. Back up data before installing the RAID card.
Step 2. Shut down the system.
Step 3. Power off the system, and unplug the power cord.
Step 4. Remove the PCI card cage (refer to “Removing and Replacing PCI Cards” in the HP rx2620
Maintenance Guide).
Step 5. Disconnect the SCSI cable(s) from the internal SCSI backplane.
62
Chapter 2
RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
Step 6. Install the Install the Smart Array 6402 or 6404 card.
Figure 2-1 Smart Array 6402 RAID Card (SA 6404 RAID Card not shown)
The following table lists the RAID card components.
Table 2-2
RAID Card Components
Item
ID
Description
1
Internal SCSI connector, port A1
2
Internal SCSI connector, port A2
3
External SCSI connector, port A1
4
External SCSI connector, port A2
5
Controller battery
6
Battery-backed cache module
7
Connector for expansion board
Step 7. Slide the RAID card edge-connector into the slot until it is fully seated.
Step 8. Route the new SCSI cable(s) from the internal disks to the Smart Array card and connect the
cables.
a. For simplex mode, connect SCSI cable A7231-63024 to connector A1 on the RAID card. Do not
connect any other SCSI cables.
b. Leave connector A-2 available for external connections.
Step 9. Replace the PCI card cage and top cover and power up the system.
Chapter 2
63
RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
Step 10. Configure logical drive and install operating system. (See “Setting up a Smart Array RAID Card As
a Boot Device” on page 65 for detailed instructions.)
Installing Smart Array RAID for Duplex Configuration
The RAID card comes pre-configured. You do not have to set any jumpers or connectors.
Step 1. Back up data before installing the RAID card.
Step 2. Shut down the system.
Step 3. Power off the system, and unplug the power cord.
Step 4. Remove the PCI card cage (refer to “Removing and Replacing PCI Cards” in the HP rx2620
Maintenance Guide.
Step 5. Disconnect the SCSI cable(s) from the internal SCSI backplane.
Step 6. Install the Smart Array RAID card and slide the RAID card edge-connector into the slot until it is
fully seated.
Step 7. Route the SCSI cable(s) from the internal disks to the Smart Array cards and reconnect the cables.
a. For duplex mode, connect SCSI cable A7231-63025 to connector A2 on the RAID card; and
connect SCSI cable A7231-63024 to connector A1 on the RAID card.
Step 8. Replace PCI card cage and top cover and power up the system.
Step 9. Configure logical drive and install operating system. (See “Setting up a Smart Array RAID Card As
a Boot Device” on page 65 for detailed instructions.)
CAUTION
Do not operate the server for long periods without the cover installed. Operating the server
without the cover results in improper airflow and improper cooling that can lead to thermal
damage.
WARNING
To reduce the risk of personal injury or damage to the equipment, consult the safety
information and user documentation provided with your server before attempting
installation.
64
Chapter 2
RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
Setting up a Smart Array RAID Card As a Boot Device
The Smart Array RAID card can be set up as a boot device.
NOTE
For PA-RISC systems, use Ignite/UX and saconfig to create the logical drives. For Integrity
systems, use the Option ROM Configuration for Arrays (ORCA) to create the logical drives.
Offline Configuration of HP-UX 11i v1 or HP-UX 11i v2 Using Ignite-UX
To set up a Smart Array 6402 Controller as a boot device, you must install HP-UX 11i v1 or HP-UX 11i v2 on
one of the controller’s logical drives. Follow this procedure:
Step 1. Start Ignite-UX from the HP-UX 11i v1 or HP-UX 11i v2 Core OS Install and Recovery Media. The
Ignite-UX Welcome screen displays:
Welcome to Ignite-UX!
Use the <tab> key to navigate between fields, and the arrow keys
within fields. Use the <return/enter> key to select an item.
Use the <return/enter> or <space-bar> to pop-up a choices list. If the
menus are not clear, select the "Help" item for more information.
Hardware Summary:
System Model: 9000/800/A500-5X
+---------------------+----------------+-------------------+ [ Scan Again ]
| Disks: 3 (204.6GB) | Floppies: 0
| LAN cards:
1
|
| CD/DVDs:
0
| Tapes:
0
| Memory:
4096MB |
| Graphics Ports: 0
| IO Buses: 7
| CPUs:
1
| [ H/W Details ]
+---------------------+----------------+-------------------+
[
Install HP-UX
]
[
Run a Recovery Shell
]
[
Advanced Options
]
[
Reboot
]
[
Help
]
Step 2. Select Run a Recovery Shell. The Recovery Shell screen displays:
NOTE:
Creating the second RAM disc and mounting on /dev ...
* Generating device file for the second ramdisc...
* Loading mkfs to make a file system...
version 4 layout
15625 sectors, 15625 blocks of size 1024, log size 1024 blocks
unlimited inodes, largefiles not supported
15625 data blocks, 14529 free data blocks
1 allocation units of 32768 blocks, 32768 data blocks
last allocation unit has 15625 data blocks
* Loading mount to mount/dev/ram1 file system...
* Mounting /dev/ram1 file system succeeded!
* Copying /dev.old files back to /dev succeeds!
* Loading insf to create disk device files...
* Creating disk device files...
* Loading in a shell...
NOTE:
Pushing a shell, you will have to use "reboot" to reboot the system when done. Use
the "loadfile" command to bring in more commands as you need them.
#
Chapter 2
65
RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
Step 3. At the recovery shell prompt, enter:
loadfile -l INSTCMDS /opt/raidsa/bin/ciss_insf
# loadfile -l INSTCMDS /opt/raidsa/bin/ciss_insf
Step 4. Verify that the device file for the Smart Array 6402 Card, or the Smart Array 6404 Card has been
created. At the next prompt, enter:
/opt/raidsa/bin/ciss_insf
Step 5.
NOTE
The following example is for the Smart Array 6402 Card. The Smart Array 6404
Card has more devices that what is shown for the 6402 card.
# /opt/raidsa/bin/ciss_insf
Installing special file for Smart Array 6402
/dev/ciss3 installed
Step 6. At the prompt enter:
loadfile -l INSTCMDS /opt/raidsa/bin/saconfig
# loadfile -l INSTCMDS /opt/raidsa/bin/saconfig
Step 7. Configure the array(s) and logical drive(s) following the instructions for the saconfig configuration
utility. You must enter the entire path /opt/raidsa/bin/saconfig /dev/cissX for saconfig to
run.
Step 8. Once you configure the logical drive(s) and array(s), exit the recovery shell by entering reboot at
the prompt. The system reboots and you are returned to the Boot Console Handler (BCH) prompt.
Step 9. At the BCH prompt, start Ignite-UX from the HP-UX 11i v1 or HP-UX 11i v2 Core OS Install and
Recovery Media. The Ignite-UX Welcome screen displays (see Step 1).
Step 10. Choose Install HP-UX.
Step 11. Choose the Advanced installation option.
The installation starts, and the Ignite-UX graphical interface (GUI) launches.
Step 12. Under the Basic tab, select the configuration to use HP-UX system.
Step 13. Select the Smart Array 6402, or Smart Array 6404 logical drive on which you want to install the
HP-UX operating system.
66
Chapter 2
RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
Step 14. Verify that the Software tab (next to the Basic tab referenced in the previous step) contains the
following entry:
Step 15. Complete the installation.
Step 16. Once the installation is complete, you can boot from the Smart Array 6402 logical drive.
Configuring the Server for RAID
To complete the installation and set up RAID for your server’s internal hot swap drives, follow the
instructions in the HP A9890A Smart Array 6402 Controller User Guide: or the HP A9891A Smart Array
6404 Controller User Guide on http://docs.hp.com/
•
Install and use operating system-specific HP Smart Array 6402 and HP Smart Array 6404 utilities and
software that help you manage your RAID.
•
Configure the HP Smart Array 6402 and the HP Smart Array 6404 for an external RAID storage system.
Chapter 2
67
RAID - Smart Array 6402 or 6404 Controller for Internal RAID Installation
Smart Array 6402 RAID or 6404 RAID Cards
68
Chapter 2
Index
C
communications interference, 17
component locations, 24
connector locations, 25
E
electrostatic discharge, 17
environmental considerations, 17
ESD precautions
ESD kit, part number, 17
I
interference, 17
L
location
pull tab, 63
M
management processor card
removing and replacing, 38
P
processor
location, 31
processor airflow guide
removing and replacing, 28
R
removing and replacing
management processor card, 38
processor airflow guide, 28
system board, 42
system covers and bezels, 20
S
safety considerations, 17
service tools required, 16
system board
removing and replacing, 42
system covers and bezels
removing and replacing, 20
T
tools, 16
W
wrist strap, 17
69
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising