DSC | PowerSeries PC1832 | Installation guide | DSC PowerSeries PC1832 Installation guide

DSC PowerSeries PC1832 Installation guide
PowerSeries
PC1616/PC1832/PC1864 version 4.2 NA
Installation Guide
WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability the manufacturer. The entire manual should be carefully read.
Table of Contents
Section
Description
Page
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
Installation & Wiring............................................................................................ 1
Keybus Wiring .................................................................................................. 2
Zone Wiring...................................................................................................... 2
Zone Expanders............................................................................................... 2
Bell Wiring ........................................................................................................ 2
AUX Power Wiring............................................................................................ 4
PGM Wiring...................................................................................................... 4
Telephone Line Wiring...................................................................................... 4
Ground ............................................................................................................. 4
Battery.............................................................................................................. 4
AC Wiring ......................................................................................................... 4
2
2.1
2.2
2.3
2.4
2.5
User Commands .................................................................................................. 5
Away Arming .................................................................................................... 5
Stay Arming...................................................................................................... 5
Disarming ......................................................................................................... 5
[ ] Commands ................................................................................................. 5
Function keys ................................................................................................... 7
3
3.1
3.2
3.2.1
3.2.2
3.3
3.3.1
3.3.2
3.3.3
3.3.4
Programming ....................................................................................................... 8
Template Programming .................................................................................... 8
DLS Programming............................................................................................ 8
Local Programming .......................................................................................... 8
Remote Programming (via telephone line)....................................................... 8
Advanced Keypad Programming...................................................................... 8
Programming Toggle Options........................................................................... 9
Programming Decimal & Hexadecimal Data .................................................... 9
How to Exit Programming................................................................................. 9
Viewing Programming ...................................................................................... 9
4
Programming Descriptions............................................................................... 10
5
Programming Worksheets ................................................................................ 27
6
For the Record ................................................................................................... 52
7
Zone Programming Summary .......................................................................... 53
App A
Reporting Code Formats (Contact ID, SIA) .............................................. APP A
App B
UL Listing Requirements ........................................................................... APP B
App C
SIA False Alarm Reduction Quick Reference Chart ................................ APP C
App D
Troubleshooting Guide .............................................................................. APP D
App E
Template Programming.............................................................................. APP E
Section 1: Installation & Wiring
Section 1: Installation & Wiring
This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616,
PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual which
can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com.
All necessary information required to meet UL Listing requirements is included in this document.
Technical Summary
FEATURES
OUT Of THE BOX
Qty 1
Qty 1
Qty 1
Qty 1
Qty 2
Qty 1
Qty 4
Qty 16
Qty 1
Qty 1
Qty 1
Cabinet
PC Module
Installation guide
User manual
Cabinet Label
Cabinet Door Plug
Standoffs
5.6KΩ Resistors
2.2KΩ Resistor
1.0KΩ Resistor
Grounding Kit
SPECIFICATIONS
Temp Range ......... 0°C-49°C (32°F-120°F)
Humidity (Max) ............................ 93%R.H.
Power Supply ........ 16.5VAC/40VA @60Hz
Current Draw (Panel)...........110mA (nom.)
Aux+ Output ........... 11.1-12.6VDC/700mA
Bell Output.............. 11.1-12.6VDC/700mA
PC1616
PC1832
PC1864
On-board Zones
6
8
8
Hardwired Zones
16 (1xPC5108)
32(3xPC5108)
64 (7xPC5108)
Wireless Zones
32
32
32
On-board PGM Outputs
PGM 1 - 50mA
PGM 2 - 300mA
PGM 1 - 50mA
PGM 2 - 300mA
PGM 1, 3, 4 - 50mA
PGM 2 - 300mA
PGM Expansion
8x50mA (PC5208)
4x500 mA (PC5204)
8x50mA (PC5208)
4x500 mA (PC5204)
8x50mA (PC5208)
4x500 mA (PC5204)
Keypads
8
8
8
Partitions
2
4
8
User Codes
47 + Master Code
71 + Master Code
94 + Master Code
Event Buffer
500 Events
500 Events
500 Events
Transformer Required
16.5VAC/40VA
16.5VAC/40VA
16.5VAC/40VA
Battery Required
4Ah / 7Ah/14AHr
4Ah / 7Ah/14AHr
4Ah / 7Ah/14AHr
Bell Output
12V/700 mA (cont)
12V/700 mA (cont)
12V/700 mA (cont)
Keypad Zone Support
COMPATIBLE DEVICES
Keypads (Backward compatible with all PowerSeries keypads)
PK55XX Keypad............................................................... 125mA (max.)
RFK55XX Keypad ............................................................ 135mA (max.)
LCD5511 Fixed Message LCD Keypad ............................ 85mA (max.)
LED5511Z 8-zone LED Keypad ...................................... 100mA (max.)
Cabinets
PC5003C...........................................222x298x78mm (11.3x11.7x3.0in)
PC500C (residential burg only) ...........213x235x78mm (8.4x9.25x3.0in)
PC4050CAR (UL commercial burg)305x 376x124mm (12.0x14.8x4.9in)
CMC-1 (UL commercial burg) ...........287x297x76mm (11.3x11.7x3.0in)
Suttle, SAE 14 ...........................355.6 x 362x 95mm (14x14.25x 3.75in)
Suttle, SAE 21 ...........................533.4 x 362x 95mm (21x14.25x 3.75in)
Suttle, SAE 28 ...........................711.2 x 362x 95mm (28x14.25x 3.75in)
Suttle, SAE 42 .........................1066.8 x 362x 95mm (42x14.25x 3.75in)
Modules
T-Link TL150*TL-250/TL300 .......................................... 275/350mA
PC5100 2-wire Interface .......... 40mA plus devices to 170mA max.
PC5132-433 Wireless Receiver ........................................... 125mA
RF5108-433 Wireless Receiver ........................................... 125mA
PC5108 Zone Expander ......................................................... 30mA
PC5200 Power Supply ............................................................ 20mA
PC5204 Power Supply with 4 Programmable Outputs .......... 30mA
PC5208 Low Current Programmable Output Module ............ 50mA
PC5400 Printer ....................................................................... 65mA
PC5401 Bi-Directional RS232 Module (Not UL Listed) .......... 65mA
Escort5580 Telephone Interface Module ............................. 130mA
*The T-Link TL-150 is not UL/ULC listed
Refer to the Reference Manual for additional devices.
Refer to the Reference Manual for alternate control cabinets
Classified in Accordance with ANSI/SIA CP-01-2000 (SIA-FAR)
Installation
Begin the installation by mounting additional modules in the cabinet using the standoffs provided, then mount the cabinet in a dry
protected area with access to unswitched AC power.
Install Hardware in the sequence indicated in the following pages. Do NOT apply power until installation is complete.
All wiring entry points are designated by arrows. All circuits are classified UL power limited except for
the battery leads. Minimum 1/4” (6.4mm) separation must be maintained at all points between power
limited and non-power limited wiring and connections.
1
PowerSeries - PC1616/PC1832/PC1864
1.1 Keybus Wiring
The 4-wire KEYBUS (red, black, yellow and green) is the communication connection between the control panel and all modules.
The 4 KEYBUS terminals of all modules must be connected to the 4 KEYBUS terminals of the main control panel.
The following rules must be followed when wiring the Keybus:
•
•
•
•
Minimum 22 AWG wire, maximum 18 AWG (2-wire twisted preferred
Do NOT use shielded wire
Modules can be home run, connected in series or can be T-tapped provided that the maximum wire distance from the control panel to any
module does not exceed 1,000 feet (305m)
No more than 3,000 feet (915m) of wire can be used in total
150’ (46m)
150’ (46m)
500’ (152m)
CONTROL
PANEL 500’ (152m)
1.2 Zone Wiring
Zones can be wired for Normally Open, Normally Closed Contacts with
Single-end-of-line (SEOL) resistors or Double End-of-Line (DEOL) resistors. Observe the following guidelines
•
•
•
•
For UL Listed Installations use SEOL or DEOL only.
Minimum 22 AWG wire, maximum 18 AWG
Do NOT use shielded wire
Wire run resistance shall not exceed 100Ω. Refer to the chart below.
Normally Closed Loops - Do NOT use for UL Installations
Single End-of-Line Resistor Wiring
Burglary Zone Wiring Chart
Wire
Gauge
Maximum wire Length to
End-of-line Resistor
(feet/meters)
22
3000 / 914
20
4900 / 1493
19
6200 / 1889
18
7800 / 2377
Figures are based on maximum wiring
resistance of 100Ω
•
•
•
•
Section [001]-[004] Selects Zone Definition
Section [013] Opt [1] Selects Normally Closed or EOL resistors
Section [013] Opt [2] Selects Single EOL or Double EOL resistors.
Section [101]-[108] Opt [14], [15], [16] Selects Normally Closed Single
EOL or Double EOL for on-board zones (PC1864, PC1832,Zone 1-8;
PC1616, Zone 1-6),
Zone Status - Loop Resistance/Loop Status
• Fault - 0Ω (shorted wire/loop)
• Secure - 5600Ω (contact closed)
Double End-of-Line Resistor Wiring
• Tamper - infinite (broken wire, open)
• Violated - 11,200Ω (contact open)
1.3 Zone Expanders
Zone expanders add zones in groups
of eight to the Alarm system. Module
jumpers J1,J2,J3 are required to
assign zones to these modules.
Jumper settings for PC5108v2 are
shown here.
• PC5108v1.0 supports first 32 zones only.
• PC5700 enrolls as two modules
• Do NOT use PC5108v1 &v2 on the same
panel.0
Module
Jumpers
J1 J2 J3
Zones
Assigned
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Zones Disabled
Zones 09-16
Zones 17-24
Zones 25-32
Zones 33-40
Zones 41-48
Zones 49-56
Zones 57-64
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
Refer to to the associated installation sheet for Jumper locations for the
PC5108v1, or PC5700
1.4 Bell Wiring
These terminals supply 700mA of current at 12VDC for commercial installations and 11.1-12.6 VDC for
residential installations (e.g.DSC SD-15 WULF). To comply with NFPA 72 Temporal Three Pattern
requirements: Program Section [013] Opt [8] ON.
NOTE: Steady, Pulsed alarms are also supported.
The Bell output is supervised and power limited by 2A PTC. If unused, connect a 1000Ω resistor across Bell+
and Bell- to prevent the panel from displaying a trouble. See [ ][2].
2
Installation
PC1616/1832/1864 Wiring Diagram
North America Only
POWER LIMITED
Stand Off
PC Board
Cable Tie (not supplied) recommended
Cabinet
2. Position circuit board
mounting holes over
standoffs. Press firmly
on board to snap-in-place.
DSC
UA503
Primary:120VAC/60Hz.
Secondary: 16.5VAC 40VA
DSCPTD 1640U
Class II Transformer
220
1. Inser t Stand off into cabinet
mounting hole in the
desired location. Snap-inplace.
PC1616/1832/1864
WARNING:
NOTE: Do not connect
transformer to receptacle
controlled by a switch
High Voltage. Disconnect AC Power
and telephone lines before servicing
PC1864
Only
PC1864
PC1832
Only
CON1
BAT+BAT-
TB-2
AC AC
AUX+
BELL+
PGM1
PGM3
AUXBELL- RED BLK YEL GRN
PGM2
PGM4 Z1 COM Z2
Z3 COM Z4
Z5 COM Z6
Z7 COM Z8 EGND
RING
TIP
R-1
T-1
230 VAC/50 Hz International
CON1
BAT+BAT-
See Section 9
for ground wiring details
AC AC
12V / 7 AHr
To EGND
Terminal
12V / 7 AHr
BLACK
16.5VAC/40VA
RED
DSC Model BD7-12
or equivalent
NON-POWER LIMITED
Battery
StandbyTime:
24Hrs min.
FUSE
WARNING: Incorrect connections may result in PTC failure or improper operation.
Inspect wiring and ensure connections are correct before applying power.
Incorrect connection of batteries may result in battery rupture or Fire Hazard.
Do NOT allow metal objects to connect the Positive and Negative Terminals.
Ensure that batteries are connected with correct polarity [Red to (+), Black to (-)].
Failure to comply with this may result in battery rupture and/or Fire Hazard.
All circuits are classified for UL Installations as Power Limited/Class II Power Limited
except for battery leads which are not power limited.
IMPORTANT:
Do NOT route any wiring over circuit boards. Maintain at least 1"(25.4mm) separation.
A minimum of 1/4" (6.4mm) separation must be maintained at all points between
power limited wiring and all other non-power limited wiring.
a)This equipment, Alarm Controller PC1616/1832/1864 shall
be installed and used within an environment that provides the
pollution degree max 2 and overvoltages category II
NON-HAZARDOUS LOCATIONS, indoor only. The equipment is
FIXED and PERMANENTLY connected and is designed to be
installed by service persons only; [service person is defined as a
person having the appropriate technical training and experience
necessary to be aware of hazards to which that person may be
exposed in performing a task and of measures to minimize the risks
to that person or other persons.]
220
UA503
b)The connection to the mains supply must be made as per the local
authorities rules and regulations.
An appropriate disconnect device must be provided as par t of the
building installation. Where it is not possible to rely on identification of
the neutral in the AC Mains supply the disconnecting device must
disconnect both poles simultaneously (line and neutral). The device
shall disconnect the supply during servicing.
PC1616/1832/1864
PC-LINK
AUX+ and Keybus (Red) are Internally Connected
Total current draw from Keypads, PGM Outputs and
Aux circuits must not exceed 700mA
c)The equipment enclosure must be secured to the building structure
before operation.
10
Internally Connected
e)Internal wiring must be routed in a manner that prevents:
- Excessive strain on wire and on terminal connections;
- Loosening of terminal; connections;
- Damage of conductor insulation
f) Disposal of the used batteries shall be made according to the waste
recovery and recycling regulations applicable to the intended market.
DSC
REV XX
PC1864
Only
PC1864
PC1832
Only
CON1
BAT+BAT-
TB-2
AC AC
AUX+ BELL+
PGM1
PGM3
AUXBELL- RED BLK YEL GRN
PGM2
PGM4 Z1 COM Z2
Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 EGND
RING
TIP
R-1
T-1
g) Before servicing, DISCONNECT the telephone connection.
WARNING:
High Voltage. Disconnect AC Power
and telephone lines before servicing
8
9
4
3
1
5
2
7
6
See corresponding Section NumberText for wiring details.
3
PowerSeries - PC1616/PC1832/PC1864
1.5 AUX Power Wiring
The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LED’s etc. If the total
current required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below.
Min/max operating voltages for devices, sensors and modules is 9.5VDC - 14VDC
Refer to the list of Compatible Devices on page 1 and/or the Reference Manual for the current draw of individual devices
1.6 PGM Wiring
PGMs switch to ground when activated by control panel.
Connect the positive side of the device to be activated to the AUX+
Terminal. Connect the negative terminal to the PGM.
current output is as follows
• PGM 1, 3, 4............................................................................... 50mA
• PGM 2..................................................................................... 300mA
For currents levels greater than 300mA a relay is
required. PGM2 can also be used for 2-wire smoke
detectors.
NOTE: Use SEOL resistors on Fire Zones ONLY.
PGM 1, LED output with current limiting resistor and
Optional Relay driver output
2-wire Smoke Detectors Initiating Circuit
• Style B (Class B), Supervised, Power Limited
• UL Compatibility Identifier .................................................... PC18-1
• DC Output Voltage........................................................9.8-13.8 VDC
• Detector Load ............................................................... 2mA (MAX)
• Single-end-of-line (SEOL) Resistor ........................................ 2200Ω
• Loop Resistance.............................................................. 24Ω (MAX)
• Standby Impedance..................................................... 1020Ω (ΝΟΜ)
• Alarm Impedance.......................................................... 570Ω (MAX)
• Alarm Current .............................................................. 89mA (MAX)
UL Compatibility ID For FSA-210B Series is: FS200
4-wire Smoke Detectors
NOTE: For ULC Listed installations use FSA-210A and FSA-410A series
RM-1/RM-2 POWER LOOP
SUPERVISORY RELAY
1.7 Telephone Line Wiring
Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ31x Connector as indicated. Use 26 AWG wire minimum for wiring.
For connection of multiple devices to the telephone line, wire in the
sequence indicated.
Telephone format is programmed in section [350].
Telephone Call Directions are programmed in section [351]-[376].
1.8 Ground
1.9 Battery
Ground Installation
Tighten nut to break paint and make
good connection to the cabinet
A sealed, rechargeable, lead acid
battery or gel type battery is required
to meet UL requirements for power
standby times.
NOTE: UL Residential/Commercial
Burglary installations require
4Hrs Power Standby time.
NOTE: UL/ULC Residential Fire &
Health Care installations require 24
Hr. power standby. ULC Commercial
Burglary and Fire monitoring installations require 24 Hr. power standby.
T-1
R-1
TIP
RING
RJ-31X
1.10 AC Wiring
Standby Battery Guide
Battery Charging Current: 400 mA
Batt
Standby
Size
4Hr
24Hr
-------------------------------------------------
4Ahr
7Ahr
14Ahr
700mA
700mA
700mA
---180mA
470mA
NOTE:
Battery capacity will deteriorate with
age and number of charge/discharge
cycles. Replace every 3-5 years.
AC Wiring
UL Listed
Installations
Primary: 120VAC/
60Hz./0.33A
Secondary:
16.5VAC/40VA
DSC PTD 1640U
Plug-in, Class 2
Transformer.
Use DSC PTD 1640U
for Canadian Installations
NOTE: Do not connect transformer to a receptacle controlled by a switch. (UL Listed Installations Only)
4
Section 2: User Commands
Section 2: User Commands
Any system keypad can be used to program or perform any keypad command. LED keypads use status and zone indicator lights to represent
alarm functions and status. The LCD keypad displays the description and status indicator lights represent alarm functions and status. This section
describes basic keypad commands. Refer to the PC1616/1832/1864 Reference Manual for detailed description of all keypad commands.
Press the [#] key to reset the keypad if an error has been made entering user codes or keypad commands.
Section 2.1 – Away Arming
The Ready light must be ON to arm the system. If the Ready light is OFF, ensure all protected doors and windows are secure or bypassed. To
arm the system in the Away mode, either press and hold the Away function button for 2 seconds or enter a valid user code and leave the premises through a door programmed as Delay. Upon arming, the Armed light will turn ON. If a user code was used to arm the system and Stay/
Away zones are programmed, the Bypass light will turn ON and will turn OFF when a door programmed as Delay is violated. If the Audible
Exit Delay option is enabled, the keypad will beep once every second during the exit delay (and three times a second during the last 10 seconds) to alert the user to leave.
Section 2.2 – Stay Arming
The Ready light must be ON to arm the system. If the Ready light is OFF ensure all protected doors and windows are secure or bypassed. To
arm the system in the Stay mode, either press and hold the Stay function button for 2 seconds or enter a valid user code and stay within the
premises (do NOT violate a door programmed as Delay). Upon arming, the Armed light and Bypass light will turn ON. If the Stay function
button is used, the keypad will not beep during the exit delay. If a user code was used, the keypad will beep if the Audible Exit Delay option
is enabled.
Section 2.3 – Disarming
The user must enter through a door programmed as Delay. Upon entering, the keypad will emit a steady tone (and emit a pulsing tone during
the last 10 seconds of entry delay) to alert the user to disarm the system. Enter a valid user code to disarm the system. If an alarm occurred
while the panel was armed, the Memory light and the zones that went into alarm will be flashing (LED keypad) or the keypad will display
‘Alarm in Memory’ (LCD keypad). Press the [#] key to return the keypad to the Ready state.
Section 2.4 – [ ] Commands
The following is a list of the [ ] commands available and a description of each:
[
[
[
[
[
[
[
[
[
[
][1]
][2]
][3]
][4]
][5]
][6]
][7][x]
][8]
][9][code]
][0]
Bypass (disarmed state)/Reactivate Stay/Away Zones (armed state)
Display Trouble Conditions
Display Alarm Memory
Door Chime Enable/Disable
User Code Programming
User Commands
Command Functions 1 – 4
Installer Programming
No-Entry Arming
Quick Arm (disarmed state)/Quick Exit (armed state)
[ ][1] Bypass/Re-activate Stay/Away Zones
LED Keypad:
Press [ ][1] to enter the bypass mode. If the Code Required for Bypass option is enabled, enter a valid user code. The Bypass light will
flash. The keypad will turn ON the corresponding zone light to indicate a zone is bypassed. To bypass or unbypass a zone, enter the 2-digit
zone number. Once the correct zones are bypassed, press [#] to exit. The Bypass light will be ON if any zones are manually bypassed.
LCD Keypad:
Press [ ][1] to enter the bypass mode. If the Code Required for Bypass option is enabled, enter a valid user code. The keypad will display
‘Scroll to View Zones’. The keypad will display the programmed zone labels for the zones and include the letter ‘O’ in the bottom, right corner if the zone is violated or the letter ‘B’ if the zone is bypassed. Scroll to the appropriate zone and press the [ ] key to change the bypass
status (or enter the 2-digit zone number). Once the correct zones are bypassed, press [#] to exit.
Additional Bypass Commands:
Bypass Recall:
Clear Bypass:
Save Bypass:
Recall Save:
Press [99].
Press [00].
Press [95].
Press [91].
The keypad will recall the last group of zones that were bypassed
The keypad will clear the bypass on all zones.
The keypad will save which zones are manually bypassed.
The keypad will recall the bypassed zones that were saved.
Hold Up Zones cannot be assigned to bypass groups.
Re-activate Stay/Away Zones:
Press [ ][1] when the system is armed in the Stay mode to change the armed status to Away mode. The system will add the Stay/Away
zones back into the system after the exit delay time expires.
5
PowerSeries - PC1616/PC1832/PC1864
[ ][2] Trouble Display
Refer to Appendix D – Trouble Conditions, for troubleshooting assistance and a detailed description of all trouble conditions.
Press [8] on any keypad or [ ] on the trouble on any PK series keypad to enter the time and date programming menu. This option
will be available if a Loss of Clock trouble is present on the system. A General System Supervisory caused by a hardwired or wireless zone expander cannot be overidden by this method. If Section [701] option 3 is ON arming will be inhibited if a system low
battery or AC trouble is detected and cannot be overridden by this method.
[ ][3] Alarm Memory Display
The Memory light will be ON if an alarm occurred during the last armed period. Press [ ][3]. The Memory light will flash and the keypad
will display the zones that went into alarm.
: To clear the Memory light, arm then disarm the system.
[ ][4] – Door Chime Enable/Disable
Press [ ][4]. The keypad will emit 3 rapid beeps if the door chime feature is now enabled and a steady 2-second tone if it is now disabled.
The same function can be performed by pressing and holding the Chime function button for 2 seconds.
[ ][5] – Program User Codes
The following table identifies available user codes:
Code
Type
Function
[01]-[39], [41]-[95]
General User Codes
arm, disarm
[40]
Master Code
all functions
Programming User Codes:
LED Keypad:
Press [ ][5] followed by the Master Code. The Program light will flash. The keypad will turn ON the corresponding zone lights to indicate
if any user codes are programmed. To add or change a user code, enter the 2-digit user code to be programmed. The zone light will flash.
Enter a new 4 or 6-digit user code or press [ ] to delete the user code. After the user code is programmed or deleted, the zone light corresponding to the user code will stop flashing. To add or change another user code, enter the 2-digit user code to be programmed or press [#] to
exit.
LCD Keypad:
Press [ ][5] followed by the Master Code. The keypad will display the first user (user 01) and include the letter ‘P’ in the bottom, right corner if the user code is programmed. Scroll to the appropriate user and press the [ ] key to program the user (or enter the 2-digit user number). Enter a new 4 or 6-digit user code or press [ ] to delete the user code. After the user code is programmed or deleted, scroll to another
user or press [#] to exit.
Programming Partition Assignment:
Press [ ][5] followed by the Master Code or Supervisor Code. Press [98] followed by the 2-digit user to change to the partition assignment.
The keypad will turn ON the corresponding zone light to indicate which partition(s) the user is assigned to. For example, if zone light 1 is
ON, the user is assigned to partition 1. To change the partition assignment, press the number corresponding to the partition. Once the correct
partitions are assigned to the user, press [#] to exit. To change the partition assignment for another user, press [98] followed by the 2-digit
user number. When finished, press [#] to exit.
Programming User Attributes:
Press [ ][5] followed by the Master Code or Supervisor Code. Press [99] followed by the 2-digit user to change to the user attributes. The
keypad will turn ON the corresponding zone light to indicate which attributes are assigned to the user.
Light [1]
Light [2]
Light [3]
Light [4]
Light [5]
Light [6]
Light [7]
Light [8]
User can enter User Code Programming section with this code
Duress Reporting Code is sent whenever this code is entered
User can manually bypass zones
User can access the Escort5580 module remotely
For Future Use
For Future Use
The panel will squawk the bell output when the user arms/disarms
One-time use code – Can disarm the system once per day and is reset at midnight.
To change the user attributes, press the number corresponding to the attribute. Once the correct attributes are assigned to the user, press [#] to
exit. To change the user attributes for another user, press [99] followed by the 2-digit user number. When finished, press [#] to exit.
6
Section 2: User Commands
[ ][6] – User Functions
Press [ ][6] followed by the Master Code, then press the number corresponding to the following functions.
[1]
Program Time and Date: Enter the time and date using the following format [HH:MM] [MM/DD/YY]. Program the time using
military standard (e.g., 8:00 pm = 20:00 hours).
[2]
Auto-arm/Auto-disarm Enable/Disable: The keypad will emit 3 rapid beeps if the Auto-arm/Auto-disarm feature is now enabled
and a steady 2-second tone if it is now disabled.
[3]
Auto-arm Time/Day: Press the number corresponding to the day of the week (1=Sunday, 2=Monday etc.) followed by the autoarm time (HH:MM). Program the time using military standard (e.g., 8:00 pm = 20:00 hours).
[4]
System Test: The panel will perform the following; activate the bell output, keypad buzzer and all keypad status lights for 2
seconds, test the backup battery and transmit a reporting code to the central station (if programmed).
[5]
Enable DLS: The panel will temporarily enable DLS for 1 or 6 hours depending on programming (see Sect [701] opt.[7]).
[6]
User Initiated DLS: The panel will attempt to call the DLS computer.
[7]
For Future Use
[8]
For Future Use
For LCD Keypads: Scroll to the desired option then press [ ]
Additional Alphanumeric Keypad Functions:
When scrolling through the list of available functions, the following additional functions are available:
Event Buffer:
Brightness Control:
Contrast Control:
Buzzer Control:
Used to view the 500-event panel buffer
Used to adjust the display backlighting level for optimal viewing
Used to adjust the display contrast level for optimal viewing
Used to adjust the keypad buzzer tone for optimal sound
[ ][7][x] – Command Output (1-4)
Press [ ][7][x]. If the Command Output Code Required option is enabled, enter a valid user code. The panel will activate any PGM output
assigned to the command output.
[ ][8] – Installer Programming
Press [ ][8] followed by the Installer Code to enter Installer Programming. Refer to the ‘How to Program’ section for more information.
[ ][9][User Code] – No-Entry Arming
Press [ ][9] followed by a valid user code. The system will arm in the Stay mode and after the exit delay expires, it will remove entry delay.
All zones programmed as Delay will function like Instant zones. The system will flash the Armed light to indicate that the system is armed
with no entry delay.
[ ][0] – Quick Arm/Quick Exit
Quick Arm: When disarmed, press [ ][0] to arm the system. The system will arm as if a valid user code was entered.
Quick Exit: When armed, press [ ][0] to activate Quick Exit. The system will allow a single zone programmed as Delay to be violated once
during the following 2 minute time period without changing the status of the system.
Section 2.5 – Function Keys
Keypads have 5 programmable one-touch function buttons located in a column down the right-side of the keypad. These buttons can also be
activated by pressing and holding number [1] through [5] respectively for 2 seconds. The default for these function buttons on the PK series
keypads are as follows:
[1]
[2]
[3]
Stay Arm
Away Arm
Chime Enable/Disable
[4]
[5]
Fire Reset – Command Output 2
Quick Exit
7
PowerSeries - PC1616/PC1832/PC1864
Section 3: Programming
This section provides the information necessary to program all required features for a basic system as well as common applications. Refer to the
PC1616/1832/1864 Reference Manual for a complete description of all programmable features.
3.1 Template Programming
Selecting [ ][8] [Installer Code] [899] displays the current 5 digit template programming code. Refer to Appendix C - Template Programming for a detailed description of available templates and corresponding 5 digit codes. After entering a valid 5 digit template programming
code, you will be prompted to enter the following in the sequence indicated below:
This feature requires a PK55xx or RFK55xx series keypad, v.1.1 or higher.
1. Central Station Telephone Number, enter 32 Character Telephone number
Program the required Central Station phone number. Press [#] to complete your entry if less than 32 digits. This phone number will be
entered into programming section [301].
2. Central Station Account Code, enter 6-digit code
Program the required Central Station Account Code. Press [#] to complete your entry if less than 6 digits. This account code will be entered
into programming section [310].
3. Partition Account Code, enter 4-digit code
This programming section will only be prompted if Contact ID has been selected as a communications format. Program the required Partition Account Code. This Partition account code will be entered into programming section [311].
4. DLS Access Code, enter 6-digit code
Program the required DLS Access Code. Press [#] to complete your entry if less than 6 digits. This Access Code will be entered into
programming section [403].
5. Partition 1 Entry Delay 1, Partition 1 Exit Delay, enter each 3-digit delay time
Program the desired 3 digit Partition 1 Entry Delay (in seconds) followed by the desired 3 digit Partition 1 Exit Delay (in seconds). These
values will be entered in programming section [005] sub-section [01] entry 1 and 3 respectively.
6. Installers Code
Enter the required 4 or 6 digit access code installers access code (dependent on Section [701] option 5). This Installer Access Code will be
entered into programming section [006]. After the Installers Code has been programmed the keypad will return to base installers
programming menu.
All template programming information must be re-entered after performing a hardware or software
panel default.
3.2 DLS Programming
3.2.1 Local Programming:
Follow the steps below in the sequence indicated to set up local programming using DLS:
1. Initiate downloading using the DLS software
2. Connect an RS-232 to PC-Link Cable between the Computer with DLS Software installed and the alarm panel to be programmed.
Connecting the DLS PC to the panel will automatically initiate the connection.
3.2.2 Remote Programming (via telephone line):
Refer to Section [400] block on page 21 for details.
The panel battery voltage can be monitored with DLS software.
After the panel information has uploaded, battery voltage can be viewed in the DLS session window.
3.3 Advanced Keypad Programming
DSC recommends filling in the Programming Worksheet with the required programming information before programming the system. This
will reduce the time required to program and will help eliminate errors.
To enter Installer Programming press [ ][8][Installer Code]. The Program light will FLASH (programmable LCD keypad displays will
change to ‘Enter Section’). An error tone indicates the installer code entered is incorrect, Press [#] to clear any key presses and try again.
The default Installer Code is [5555].
8
Section 3: Programming
The Armed and Ready lights indicate programming status:
Armed Light ON
Ready Light ON
Ready Light FLASHING
Panel waiting for 3-digit section number
If in module programming, waiting for section # to be entered.
Panel waiting for data to be entered
Panel waiting for HEX data to be entered
You cannot enter installer programming while the system or any partition is armed or in alarm.
3.3.1 Programming Toggle Options:
Enter the 3-digit programming section number.:
•
•
•
•
•
•
The Armed light will turn OFF and
The Ready light will turn ON.
The keypad will display which toggle options are ON or
OFF according to the chart.
To toggle an option ON or OFF, press the corresponding
number on the keypad. The display will change accordingly.
Keypad Type
Option ON
Option OFF
LED
Zone Light ON
Zone Light OFF
Fixed-Message LCD
Indicator # ON
Indicator # OFF
Programmable-Message LCD
# Displayed
Dash [-] Displayed
When all the toggle options are configured correctly, press the [#] key to exit the program section.
The Ready light will turn OFF and the Armed light will turn ON.
3.3.2 Programming Decimal and Hexadecimal (HEX) Data:
•
•
•
Enter the 3-digit programming section number.
The Armed light will turn OFF and The Ready light will turn ON.
Enter the data written in the boxes.
For sections that require multiple 2 or 3 digit numbers, the keypad will double-beep after each 2 or 3 digit entry and move to the next item in
the list. After the last digit in the section is entered, the keypad will beep rapidly 5 times and exit the program section. The Ready light will
turn OFF and the Armed light will turn ON.
For sections that do not require data for every box (such as phone numbers) press the [#] key to exit the program section after entering all the
required data. The Ready light will turn OFF and the Armed light will turn ON.
At any time the [#] can be pressed to exit any program section. All changes made up to that point will be saved.
HEX (or hexadecimal) digits are sometimes required. To enter a HEX digit, press
the [ ] key to begin HEX programming. The Ready light will FLASH. Refer to the
chart below and press the number corresponding to the HEX digit required. The
Ready light will continue to FLASH. Press [ ] again to return to normal decimal
programming. The Ready light will turn ON.
Value
Enter
HEX [A]
HEX [B]
HEX [C]
HEX [D]
HEX [E]
HEX [F]
Press
Press
Press
Press
Press
Press
Telephone Dialer
[
[
[
[
[
[
][1][
][2][
][3][
][4][
][5][
][6][
]
]
]
]
]
]
Not Supported
Simulated [ ] key
Simulated [#] key
Dial tone search
Two second pause
End of Number
In addition to the standard digits 0-9, HEX digits and special dialer functions can also be programmed if required.
3.3.3 How to Exit Installer Programming:
To exit installer programming, press the [#] key when the panel is waiting for a 3-digit section number (the Armed light is ON).
3.3.4 Viewing Programming
LED and LCD5501Z Keypads
Any programming section can be viewed from an LED or LCD5501Z
keypad. When a programming section is entered, the keypad will immediately display the first digit of information programmed in that section.
The keypad displays the information using a binary format, according to
the following chart:
Press any of the Emergency keys (Fire, Auxiliary or Panic) to advance to
the next digit.
When all the digits in a section have been viewed, the panel will exit the section: the Ready light will turn OFF, and the Armed light
will turn ON, waiting for the next 3-digit programming section number to be entered.
Press the [#] key to exit the section
LCD Keypad
The keypad will immediately display all the information programmed when a programming section is entered. Use the arrow keys (< >)
to scroll through the data being displayed. Scroll past the end of the data displayed, or press the [#] key to exit the section.
9
PowerSeries - PC1616/PC1832/PC1864
Section 4 – Programming Descriptions
The following is a brief description of the features and options available in the Power PC1616/1832/1864 control panel. Refer to the PC1616/
1832/1864 Reference Manual for a complete description of all programming features, limitations and requirements.
Section [001] to [004] Zone Definitions
Option
Description
[00]
Null Zone: Zone not used
[01]
Delay 1: When armed, provides entry delay when violated (follows Entry Delay 1)
[02]
Delay 2: When armed, provides entry delay when violated (follows Entry Delay 2)
[03]
Instant: When armed, instant alarm when violated
[04]
Interior: When armed, instant alarm if the zone is violated first, will follow entry delay if entry delay is active
[05]
Interior Stay/Away: Similar to ‘Interior’ except panel will auto-bypass the zone if Armed in the Stay mode
[06]
Delay Stay/Away: Similar to ‘Delay 1’ except panel will auto-bypass the zone if Armed in the Stay mode
[07]
Delayed 24-Hour Fire (Hardwire): Instant audible alarm when violated, communication delayed 30 seconds - if alarm
acknowledged during this time (by pressing a key), the alarm will be silenced 90 seconds and repeat cycle - if not, alarm will latch
and communicate after 30 second delay
[08]
Standard 24-Hour Fire (Hardwire): Instant alarm and communication when violated
[09]
24-Hour Supervision (Hardwire): Instant alarm and communication when violated. Will not sound the bell or keypad buzzer.
[10]
24-Hour Supervisory Buzzer: Instant alarm, panel will activate keypad buzzer instead of bell output
[11]
24-Hour Burglary: Instant alarm when violated, audible alarm at default. Reporting code BA, BH
[12]
24-Hour Hold-Up: Instant alarm when violated, silent alarm at default. Reporting code HA, HH
[13]
24-Hour Gas: Instant alarm when violated, audible alarm at default. Reporting code GA, GH
[14]
24-Hour Heat: Instant alarm when violated, audible alarm at default (also known as high-temp). Reporting code KA, KH
[15]
24-Hour Medical: Instant alarm when violated, silent alarm at default. Reporting code MA, MH
[16]
24-Hour Panic: Instant alarm when violated, audible alarm at default. Reporting code PA, PH
[17]
24-Hour Emergency: Instant alarm when violated, audible alarm at default. Reporting code QA, QH
[18]
24-Hour Sprinkler: Instant alarm when violated, audible alarm at default. Reporting code SA, SH
[19]
24-Hour Water: Instant alarm when violated, audible alarm at default (also known as high water level). Reporting code WA, WH
[20]
24-Hour Freeze: Instant alarm when violated, audible alarm at default (also known as low-temp). Reporting code ZA, ZH
[21]
24-Hour Latching Tamper: Instant alarm when violated, panel cannot be armed until Installer Programming is entered
[22]
Momentary Keyswitch Arm: Arm or disarm the system when violated
[23]
Maintained Keyswitch Arm: Arm system when violated, disarm system when restored
[24]
For Future Use
[25]
Interior/Delay: Zone will function like an Interior zone when armed in Away mode, like a Delay zone when armed in the Stay
mode
[26]
24-Hour Non-Alarm: Zone will NOT create an alarm. Can be used with zone follower function for automation applications
[29]
Auto-Verified Fire: When violated, system will reset all smoke detectors for 20 seconds, then wait 10 seconds for detectors to
settle. If another fire alarm detected within 60 seconds zone will go into alarm immediately
[30]
Supervisory: Instant alarm, system will activate keypad buzzer. A valid user code is required to silence Keypad buzzer.
[31]
Day Zone: Instant alarm when system is armed, keypad buzzer (no alarm) when system is disarmed
[32]
Instant Stay/Away: Similar to ‘Instant’ except panel will auto-bypass the zone if Armed in the Stay mode
[35]
24-Hour Bell/Buzzer: Instant alarm when violated, system will activate bell output if armed, keypad buzzer if disarmed
10
Section 4 – Programming Descriptions
[36]
24-hr. Non-Latching Tamper Zone: Instant tamper condition when violated. Active in both the armed and disarmed state.
[37]
Night Zone: Functions like Interior Stay/Away but will remain bypassed if the user presses [ ][1] to re-activate Stay/Away zones
when armed in the Stay mode
[87]
Delayed 24-Hour Fire (Wireless/Addressable): Same as Delayed 24-Hour Fire (Hardwire) but must be used for wireless or
addressable smoke detectors
[88]
Standard 24-Hour Fire (Wireless/Addressable): Same as Standard 24-Hour Fire (Hardwire) but must be used for wireless or
addressable smoke detectors
Section [005] System Times
After entering Section [005], enter the 2-digit subsection number for the desired partition and program the Entry Delay 1, Entry Delay 2
and Exit Delay for each active partition on the system. Valid entries are from [001] to [255] or [045] to [255] for SIA CP-01 panels (in seconds). Enter subsection [09] to program the Bell Cut-Off Time. Valid entries are from [001] to [255] (in minutes).
Section [006] Installer Code
The default Installer Code is [5555] or [555555] if 6-Digit Access Codes is enabled.
Section [007] Master Code
The default Master Code is [1234] or [123456] if 6-digit Access Codes is enabled.
Section [008] Maintenance Code
The default Maintenance Code is [AAAA] (not programmed). This code can arm any partition but cannot disarm unless the partition is in
alarm.
Section [009] to [011] PGM Outputs
The PC1616 and PC1832 have two on-board PGM outputs (PGM1 and PGM2). The PC1864 has four on-board PGM outputs (PGM1 to
PGM4). The panel has the capacity for up to 14 PGM outputs (8 additional low-current PGM outputs with PC5208 module, 4 additional
high-current PGM outputs with a PC5204 module).
PGM Output Options:
Option
Description
[00]
For Future Use
[01]
Fire and Burglary: Output will activate (steady for burglary, pulsing for fire) if an alarm occurs on the selected partition
[02]
For Future Use
[03]
Sensor Reset: Output will normally be active and deactivate for 5 seconds when a [ ][7][2] fire reset command is entered or when an AutoVerify Fire alarm is detected
[04]
2-Wire Smoke: Configures PGM2 as 2-wire smoke detector input (PGM2 only)
[05]
Armed Status: Output will activate when all of the selected partitions are armed
[06]
Ready Status: Output will activate when all the selected partitions are in the Ready state (Ready light ON)
[07]
Keypad Buzzer Follow: Output will activate and follow the keypad buzzer for the selected partition when the following events occur; entry
delay, door chime, audible exit delay, automatic arming pre-alert, 24-Hour Supervisory Buzzer zone alarm
[08]
Courtesy Pulse: Output will activate during entry/exit delay if the selected partition is armed – will remain active for an additional 2
minutes after the entry or exit delay expires
[09]
System Trouble: Output will activate when any selected trouble condition is present
[10]
Latched System Event (Strobe): Output will activate when a selected condition occurs on any selected partition. Note output can be
programmed to follow timer
[11]
System Tamper: Output will activate when any tamper condition is present
[12]
TLM and Alarm: Output will activate if a telephone line trouble is present and then an alarm occurs
[13]
Kissoff: Output will activate for 2 seconds when a valid kissoff is received from the central station
[14]
Ground Start: Output will activate for 2 seconds when the panel attempts to seize the phone line (additional dial tone search must be
programmed in the central station phone number – HEX [D])
[15]
Remote Operation: Output can be activated/deactivated via the DLS software
[16]
For Future Use
[17]
Away Armed Status: Activates when all of the selected partitions are armed in Away mode
11
PowerSeries - PC1616/PC1832/PC1864
[18]
Stay Armed Status: Activates when all of the selected partitions are armed in Stay mode
[19]
Command Output 1:Activates when a [ ][7][1] command is entered on the selected partition – Command can be programmed to require a
valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[20]
Command Output 2: Activates when a [ ][7][2] command is entered on the selected partition – Command can be programmed to require
a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[21]
Command Output 3: Activates when a [ ][7][3] command is entered on the selected partition – Command can be programmed to require
a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[22]
Command Output 4: Activates when a [ ][7][4] command is entered on the selected partition – Command can be programmed to require
a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[23]
Silent 24-Hour Input: Changes PGM to a 24-Hour Silent zone (PGM2 only)
[24]
Audible 24-Hour Input: Changes PGM to a 24-Hour Audible zone (PGM2 only)
[25]
Delayed Fire and Burglary: Functions as a Fire and Burglary output but does not activate until the TX Delay time expires
[26]
Battery Test Output: Output activates for 10 seconds at midnight each day.
[28]
Holdup Output: Activates when a Holdup Alarm occurs on any assigned partition. Remains active until all assigned partitions have been
armed or disarmed. Will not activate if a Holdup Zone is goes into a fault or tamper condition.
[29]
Zone Follower (Zones 1-8): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[30]
Partition Status Alarm Memory: Activates if the selected partition is armed.
Output will pulse “one second ON / one second OFF if an alarm occurs
[31]
Alternate Communicator: Activates when selected system event occurs. If active in the armed state, it remains active until the system is
disarmed. If activated in the disarmed state, it remains active until a valid access code is entered within bell cut-off time, or when the system
is armed after bell cut-off time has expired.
[32]
Open After Alarm: Actives for 5 seconds when system has been disarmed after an alarm.
[33]
Bell Status and Programming Access Output: Activates when Bell, Installer programming mode or DLS is active. Remains active until
Bell is no longer active, Installer programming mode is exited and DLS programming is disconnected.
[34]
Away Armed with no Zone Bypassed Status: Activates when armed with stay/away zones active and no zones bypassed.
[35]
Zone Follower (Zones 9-16): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[36]
Zone Follower (Zones 17-24): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[37]
Zone Follower (Zones 25-32): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[38]
Zone Follower (Zones 33-40): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[39]
Zone Follower (Zones 41-48): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[40]
Zone Follower (Zones 49-56): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[41]
Zone Follower (Zones 57-64): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
* See Section [501]-[514] Programmable Output Attributes, PGM Output Option [29] and [35]-[41] option 8 on page 23
Section [012] Keypad Lockout
The system can be programmed to ‘lockout’ keypads if a series of incorrect user or installer codes are entered. When lockout is active, all
keypads emit a steady 2-second error tone when a key is pressed. Program the Number of Invalid Codes Before Lockout with the desired
number. Valid entries are from [000] to [255]. Program data [000] to disable the feature. Keypads will remain locked out for the number of
minutes programmed for the Lockout Duration. Valid entries are from [000] to [255].
Section [013] First System Option Code
Option
Description
[1]
ON: zones require normally-closed loops. OFF: zones require 5.6K End-Of-Line resistors.
[2]
ON: zones require double End-Of-Line resistors. OFF: zones require single End-Of-Line resistors.
[3]
ON: keypads will display all trouble conditions while armed. OFF: keypads will only display fire trouble when armed.
This option must be OFF if LCD5500 v2.x (or older) keypads are used on the system.
[4]
12
ON: only a trouble will be displayed. OFF: keypads will display a trouble and a zone violation if a tamper or fault is detected.
Section 4 – Programming Descriptions
[5]
ON: auto-arming schedules (Program Sections [181]-[188]) will be available to the user in the [ ][6] menu.
OFF: auto-arming schedules will NOT be available to the user in the [ ][6] menu.
[6]
ON: the Audible Exit Fault feature will be enabled. If a delay zone is not secured correctly and not force-armed, at the end of the exit delay,
the system will go into entry delay and turn ON the bell output. The bell will also sound if the delay zone is opened within 10 seconds of the
exit delay timeout. OFF: the keypad will sound the entry delay through the keypad as normal.
[7]
ON: the system will NOT log additional alarms for a zone that has reached the swinger shutdown threshold.
OFF: all zone alarms will be logged.
[8]
ON: Temporal Three Fire Signal is used to annunciate fire alarms
(½ second ON, ½ second OFF, ½ second ON, ½ second OFF ½ second ON, 1 ½ seconds OFF).
OFF: the system will pulse the bell output
(½ second ON, ½ second OFF).
Section [014] Second System Option Code
Option
Description
[1]
ON: the system squawks the bell output once when a partition is armed, twice when disarmed. OFF: the bell output does not
activate. Refer to section [017] option 8.
[2]
ON: the system squawks the bell output every 10 seconds during the auto-arm pre-alert. OFF: the bell output does not activate.
[3]
ON: the system will squawk the bell output once every second during Exit Delay, 3 squawks per second for the last 10 seconds.
OFF: the bell output will not activate.
[4]
ON: the system will squawk the bell output once every second during Entry Delay, 3 squawks per second for the last 10 seconds.
OFF: the bell output will not activate.
[5]
ON: the system squawks the bell output once every 10 seconds when a trouble condition is present.
OFF: the bell output does not activate.
[6]
ON: the system will beep the keypads once every second, and 3 times a second during the last 10 seconds, during exit delay when
the system is armed with a user code or armed in the Away mode. OFF: the keypads will not beep.
[7]
ON: the exit delay will be terminated (reduced to 5 seconds) when a Delay 1 zone is violated and restored after the system is armed.
OFF: the exit delay will count down as normal.
[8]
ON: the bell output will not timeout if a fire alarm occurs. The user must turn OFF the bell by entering a valid user code.
OFF: the bell output will timeout normally.
Section [015] Third System Option Code
Option
Description
[1]
ON: the keypad [F] fire emergency key will be enabled. OFF: the keypad [F] fire emergency key will be disabled.
[2]
ON: the keypad [P] panic emergency will be audible (bell output). OFF: the keypad [P] emergency key will be silent.
[3]
ON: the Quick Exit feature will be enabled. OFF: the Quick Exit feature will be disabled.
[4]
ON: the Quick Arming [ ][0] feature will be enabled. OFF: Quick Arming [ ][0] feature will be disabled.
If this feature is disabled, a valid user code must be entered after the Stay or Away function buttons are pressed.
[5]
ON: a valid user code must be entered after pressing [ ][1] to access the Bypass feature. OFF: a user code is not required.
[6]
ON: the Master Code (user code 40) can only be changed in Installer Programming. OFF: the Master Code can be changed using
the User Programming [ ][5] command.
[7]
ON: the system supervises the telephone line and displays a trouble if disconnected. OFF: the telephone line is not supervised.
13
PowerSeries - PC1616/PC1832/PC1864
[8]
ON: the system activates the bell output if a telephone line trouble is detected while the system is armed. OFF: the system activates
the keypad buzzer trouble tone.
Section [016] Fourth System Option Code
Option
Description
[1]
ON: the system supervises the AC input and displays a trouble if a failure is detected. OFF: AC Input is not supervised.
[2]
ON: the trouble light will flash when an AC trouble is detected. OFF: the trouble light turns on, does not flash.
[3]
ON: the keypad blanks (no indicator lights) if a key is not pressed for 30 seconds. OFF: the keypad does not blank.
[4]
ON: a valid user code must be entered to restore normal keypad operation after the blanking. OFF: pressing any key will return the
keypad to normal operation.
[5]
ON: keypad backlighting enabled. OFF: keypad backlighting disabled.
[6]
ON: the system temporarily enables the Keypad Blanking feature if an AC failure is detected (to preserve the back up battery).
OFF: the system will operate as normal.
[7]
ON: the keypad turns ON the Bypass light if zones are bypassed while the system is armed. OFF: the Bypass light turns OFF when
the system is armed.
[8]
ON: the system supervises keypad tampers. OFF: the system does not supervise keypad tampers.
Section [017] Fifth System Option Code
Option
Description
[1]
ON: the system does NOT associate wireless keys to user codes. OFF: the system will assign user code 17 to wireless key #01, user
code 18 to wireless key #02 etc. If the wireless key is used to arm or disarm, the system will report the Opening or Closing for the
associated User Code.
[2]
ON: the system logs an RF Jam trouble condition if the condition is present for 5 minutes. OFF: the system logs the trouble
condition after 30 seconds.
[3]
ON: the keypads beep if an RF Jam trouble is detected. OFF: the trouble is not annunciated via the keypad buzzer.
[4]
ON: the Double Hit feature will be enabled. Two violations from the same zone within the Cross Zone Timer will be considered a
valid Police Code or Cross Zone event. The system will report the event and log it to the event buffer.
OFF: two alarms from the same zone is not a valid Police Code or Cross Zone event.
[5]
ON: the system logs and communicates a Late-To-Close event when it auto-arms at the programmed time (not if auto arming was
caused by the No-Activity Arming feature). OFF: the system does not transmit or log a Late-To-Close event.
[6]
ON: enables the Daylight Savings automatic clock adjustment feature. OFF: the system does not automatically adjust the clock for
Daylight Savings.
[7]
For Future Use
[8]
ON: the system only squawks the bell output when the system is armed in the Away mode. OFF: the system squawks the siren
when the system is armed in any mode. (See Section [14]).
Section [018] Sixth System Option Code
Option
[1]
[2]-[4]
14
Description
ON: the system only transmits a Test Transmission reporting code if no other event was transmitted to the central station during the
programmed time. OFF the system always transmits a Test Transmission reporting code as programmed.
For Future Use
Section 4 – Programming Descriptions
[5]
ON: the keypad buzzer follows the bell output for all alarms. OFF: the system only activates the bell output for all alarms.
[6]
ON: When an alarm is detected on a zone (with the Cross Zone attribute enabled), a timer is started. The alarm is not transmitted and
the bell output is not activated unless a second cross zone enabled zone is violated before the Cross Zone timer times out. OFF: the
system reports all alarms normally and logs and transmits a Police Code reporting code if a second zone alarm is detected during the
armed period.
[7]
ON: The system restarts the Exit Delay (one time) if a Delay zone is violated and restored during the exit delay time. OFF: exit
delay does not restart.
[8]
ON: The system activates the trouble beeps when an AC trouble is detected. OFF: the system does not annunciate AC troubles
using the keypad buzzer.
Section [019] Seventh System Option Code
Option
Description
[1]
For Future Use
[2]
ON: Trouble light latches on OFF: Trouble light turns off after restore.
[3]
ON: When disarming, the keypad will display only the first alarm to occur during the last arming period OFF: When disarming,
the keypad will display all zones that were in alarm during the last arming period
[4]-[5]
For Future Use
[6]
ON: the green LED indicator on the keypads indicate the status of AC on the system OFF: the green LED indicator on the keypads
indicate the partition ready status
[7]
ON: All user access codes can enter the User Functions menu. OFF: Only the Master Code can enter the User Functions menu.
[8]
For Future Use
Section [020] Keypad Zone Assignment
Enter the two-digit zone number to be assigned to each keypad assigned to a specific slot. Only one keypad can be assigned to a specific slot.
See Keypad Assignment. Valid entries are from [00] to [64].
Section [021] Eighth System Option Code
Option
[1]
[2]-[5]
[6]
[7]-[8]
Description
ON: Access codes will not be accepted by the system during entry delay. OFF: An access code can be used to disarm the system
during entry delay
For Future Use
ON: Key-switches and wireless can only disarm the system during an entry delay OFF: Key-switches and wireless keys can
disarm the system regardless if entry delay is active or not.
For Future Use
Section [022] Ninth System Option Code
Option
[1]
[2]-[3]
[4]
Description
ON: An access code is required for access to the [ ][1], [ ][2], [ ][3] menus. OFF: No access code is required for [ ][1], [ ][2],
[ ][3] menu access.
For Future Use
ON: Only the Master code can be used to bypass a hold up zone. OFF: Any valid access code can bypass a hold up zone.
15
PowerSeries - PC1616/PC1832/PC1864
[5]
For Future Use
[6]
Refer to the PC1616/PC1832/PC1864 Reference Manual for RF Delinquency details.
[7]
Future Use
[8]
ON: When the system is armed in Stay mode, during the Exit delay, the system will sound 1 beep every 3 second.
OFF: When the system is armed in Stay mode, the system will be silent during the Exit delay.
Section [023] Tenth System Option Code
Option
Description
[1]
ON: the keypad [F] emergency key will only beep three times to acknowledge the button has been pressed. The system will not
activate the bell output. OFF: the system will activate the bell output and beep the keypad.
[2]
Refer to the PC1616/PC1832/PC1864 Reference Manual for 200 Baud Open/Close Identifier details.
[3]
ON: the system will only transmit the Test Transmission reporting code if the system is armed at the time the system is programmed
to report the event. OFF: the system will always report the Test Transmission reporting code at the programmed time.
[4]
ON: the system changes the Test Transmission Reporting Cycle Time from Days to Hours. OFF: the Test Transmission Reporting
Cycle Time is in Days.
[5]
ON: the user cannot switch from Away Arm mode to Stay Arm mode using the function keys. OFF: the user can switch arming
modes.
[6]
ON: the system disconnects a listen in/two-way session if a new event occurs.
OFF: the system does NOT disconnect. New events are transmitted only after the session is terminated.
[7]
ON: the system does NOT activate the keypad buzzer for any trouble condition (excluding Fire Troubles). OFF: the system
annunciates troubles via the keypad buzzer (two beeps every 10 seconds) normally.
[8]
ON: Keyswitches will always arm in away mode. OFF: Keyswitches will arm in away mode if an entry/exit zone is violated during
exit delay.
Section [030] Fast Loop Response
This section is used to determine the Loop Response Time for the main panel zones.
ON: the loop response time will be 36 mS. OFF: the loop response time will be 400 mS.
Section [101] to [164] Zone Attributes
These sections are used to customize the operation of the zones. There are 9 toggle options in each Section:
Option
16
Description
[1]
ON: alarms are audible (bell output). OFF: alarms are silent.
[2]
ON: the bell output is steady (burglary). OFF: the alarm output pulses (fire).
[3]
ON: a zone violation or restoral will activate Chime. OFF: Chime is not activated.
[4]
ON: the user can manually bypass the zone using the [ ][1] command. OFF: the zone cannot be manually bypassed.
[5]
ON: the partition can be armed even if the zone is violated (the zone will not affect the Ready status). OFF: the zone must be
secure before arming.
[6]
ON: the system shuts down alarm reporting after the programmed number of alarms have occurred. OFF: the panel will always
report the event if an alarm occurs.
[7]
ON: the system delays reporting the event for the time programmed for the Transmission Delay time. OFF: the panel
immediately transmits the reporting event when an alarm is detected.
[8]
ON: the zone is a wireless or addressable device. OFF: the zone is a hardwire zone (main panel, zone expander or keypad zone).
Section 4 – Programming Descriptions
[9]
ON: the zone has the Cross Zone feature enabled. OFF: the zone functions normally.
[10]-[13]
For Future Use
[14]
ON: the zone requires a normally-closed loop OFF: the zone will follow the EOL configuration in Section [013]
[15]
ON: the zone requires a single End-of-Line resistor OFF: the zone will follow the EOL configuration in Section [013]
[16]
ON: the zone requires a double End-of-Line resistors OFF: the zone will follow the EOL configuration in Section [013]
Options 14, 15, 16 apply to first 8 zones only. If more than one of these options are enabled then lowest numbered option is
enabled. E.g., If Option 14 and option 15 are enabled then the zones are configured as normally closed loops.
Keypad zones and zone expanders will always follow Section [013].
When Zone Types (Section [001] to [004]) are programmed, the system will change the Zone Attributes to those found in the chart included
in the Programming Worksheets. The Zone Attributes will default if a new Zone Type is programmed for a specific zone. After programming the Zone Types, enter Section [101] to [164] and ensure that all options are programmed correctly.
Ready light ON:
Program attributes [1-8] (press [1]-[8] to turn option ON or OFF)
Ready light and Armed light ON: Program attributes [9-16] (press [1]-[8] to turn option ON or OFF)
Press [9] to switch between attributes [1-8] and attribute [9-16].
Section [165] Maximum Dialing Attempts
Program the Maximum Dialing Attempts before the panel will generate a Failure to Communicate (FTC) trouble condition.
Valid entries are [001] to [005]. For UL Listed installations, 5 attempts is required.
Section [166] Post Dial Wait for Handshake
Program the maximum time the panel will wait, after dialing, for a valid handshake from the central station.
Valid entries are [001] to [255] seconds.
Section [167] T-Link Communications Wait for Acknowledgement
Program the maximum time the panel will wait, after sending a data packet, for an acknowledgement from the central station.
Valid entries are [001] to [255] seconds.
Section [168] Daylight Savings Time (Move Clock Ahead)
These sections are used to program the Date, Time and Increment that the clock will move ahead for Daylight Savings Time each year. Programming can be accomplished by programming the Month, Day, Hour and Increment or Month, Week, Day of Week, Hour and Increment:
Month
Data [001] to [012] represents January to December.
Week
Data [000] indicates that the day of the month will be programmed in the Day section below. Data [001] to [005] represents
weeks 1 to 5 of the month. Week 5 always represents the last week in the month, regardless if the number of weeks in the
month is 4 or 5.
Day
Data [001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005] was
programmed in the Week Section above, then Data [000] to [006] represents Sunday to Saturday
Hour
Data [000] to [022] represents the hour that Daylight Saving Time will take effect.
Increment
Data [001] to [002] represents the number of hours to advance the clock for Daylight Savings Time.
Do not program the Hour outside of the valid range or the time will not change. Do not program the value of the Increment to be
greater then the number of hours remaining in the current day.
Section [169] Standard Time (Set Clock Back)
These sections are used to program the Date, Time and Increment that the clock will move back for Standard Time each year. Programming
can be accomplished by programming the Month, Day, Hour and Increment or Month, Week, Day of Week, Hour and Increment:
Month
Week
Day
Hour
Increment
Data [001] to [012] represents January to December.
Data [000] indicates that the day of the month will be programmed in the Day section below. Data [001] to [005] represents
weeks 1 to 5 of the month. Week 5 always represents the last week in the month, regardless if the number of weeks in the
month is 4 or 5.
Data [001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005] was
programmed in the Week Section above, then Data [000] to [006] represents Sunday to Saturday
Data [000] or [023] represents the hour that Standard Time will take effect.
Data [001] or [002] represents the number of hours to roll back the clock for Daylight Savings Time.
17
PowerSeries - PC1616/PC1832/PC1864
Section [170] PGM Output Timer
Program the time, in seconds, PGM outputs programmed to follow the PGM Output Timer will activate for. Valid entries are [001] to [255].
Section [171] Tamper PGM Output Timer
Program the time, in minutes, that a tamper condition will latch the Tamper PGM output. Valid entries are [000] to [255].
Section [175] Auto-arm Postpone Timer
Program the time, in minutes, that the system will postpone automatic arming. After the programmed time, the system will attempt to auto
arm again. If data [000] is programmed, the system will instead abort the auto arm sequence. Valid entries are [001] to [255].
Section [176] Cross Zone/Police Code Timer
Program the time, in seconds (Cross Zone) or minutes (Police Code), that the panel will use to determine if a Cross Zone or Police Code
event has occurred. If data [000] is programmed when using the Police Code feature, the panel will generate a Police Code event if any two
zones go into alarm during any armed-to-armed period. Valid entries are [001] to [255].
Section [181] to [188] Auto-arm Schedules
Program the time to auto arm (section [181] for partition 1, Section [182] for partition 2 etc.) for each day of the week. Each section has
seven, 4-digit entries, two digits for the hour, two digits for the minute, for Sunday through Saturday. Program using the military format (for
example, to auto arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto arming.
Section [190] No Activity Arming Pre-alert Duration
Program the time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypads will provide a steady tone warning the user that
the system will arm. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255].
Section [191] to [198] No Activity Arm Timer
Program the time, in minutes, for the No Activity Arm Timer (Section [191] for Partition 1, Section [192] for Partition 2 etc.). If Delay Zones
are restored and no zone activity is detected for the time programmed, the system will start the auto arm sequence. Valid entries are [000] to
[255].
Section [199] Auto-Arming Pre-alert Timer
Program the time, in minutes, for the Auto-Arming Pre-Alert Time. This timer is used for all programmed auto-arming features (is not used
for No Activity Arming). The keypads will provide a steady tone warning the user that the system will arm. The user can enter a valid access
code to abort the arming sequence. Valid entries are [001] to [255].
Section [201] Partition Selection Mask
Turn the corresponding option ON to enable partitions [1] to [8]. ON (bit 1 cannot be turned OFF).
Section [202] to [265] Partition Zone Assignments
These Sections are used to assign zones to specific partitions (Section [202] to [209] for Partition 1, Sections [210] to [217] for Partition 2
etc.). Turn ON the option corresponding to the partition and zone to enable the zone on the specified partition. Turn the option OFF to disable the zone on the specified partition. Zones assigned to more than one partition are called ‘common zones’ and will only be armed if all
the partitions the zone is assigned to are armed. Default = Zones 1-8 enabled on Partition 1.
Section [301] to [303] Telephone Numbers
Program the phone numbers as required. Phone Number 3 is dedicated as a back-up to Phone Number 1. HEX digits can be included for special applications:
HEX [A]
Not used
HEX [B]
Simulates a [ ] key press
HEX [C]
Simulates a [#] key press
HEX [D]
Additional dial tone search
HEX [E]
2-second pause
HEX [F]
End of phone number marker
Section [304] Call Waiting Cancel String
Program the digits required to disable call waiting. If enabled, the system will dial the programmed string on the first dialing attempt.
Program unused digits with data [F].
Section [310] System Account Number
Program the System Account Number. Only the SIA format supports 6-digit account numbers. If a 4-digit account number is required,
program the last two digits as data [FF]. If using the SIA format, this account number will be used for all reporting events. If using a
18
Section 4 – Programming Descriptions
different format, this account number will be used for all events that are not partition specific (for example, low battery, AC trouble etc.).
For partition specific events the system will use the programmed Partition Account Number. For all formats other than SIA, program a HEX
[A] for any digit [0] in the account number being used.
Section [311] to [318] Partition Account Numbers
Program the Partition Account Number for each active partition (Section [311] for partition 1, Section [312] for partition 2 etc.). When using
the Automatic SIA format, these account numbers are not used. The system will use the System Account Number for all reporting events.
For all formats other than SIA, program a HEX [A] for any digit [0] in the account number being used.
Section [320] to [349] Reporting Codes
Program the reporting code for all events to be transmitted. For description of when each reporting event will be transmitted, refer to
Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable
the reporting of an event. If any other data is programmed (Data [01] to [FF]) the panel will automatically generate the correct reporting
event when transmitting to the central station. For all formats excluding Automatic SIA and Automatic Contact ID, the panel will not attempt
to report an event if data [00] or data [FF] is programmed for the reporting code.
Section [350] Communicator Format
Program the 2-digit number for the desired Communicator Format for the First Phone Number and Second Phone Number. When dialing the
Third Phone Number, the system will use the Communicator Format programmed for Phone Number 1. Valid entries are [01] to [13]. Refer
to the Programming Worksheet for a list of the available Communicator Formats. Refer to the PC1616/PC1832/PC1864 Reference Manual
for Communicator Format details.
Section [351] to [376] Communicator Call Direction Options
Reporting events are categorized into 5 groups; Alarm/Restore, Opening/Closing, Tamper Alarm/Restore, System Maintenance and Test
Transmissions. Program which Phone Number the control panel will use to transmit reporting events by turning the option ON in the correct
Section. Phone Number 1 and/or Phone Number 2 can be used.
Section [377] Communicator Variables
Program a 3-digit number for each program entry:
Swinger Shutdown (Alarms): Maximum number of alarm/restoral transmissions per zone. Valid entries: [001] to [014]. Program data [000] to
disable shutdown.
Swinger Shutdown (Tamper): Maximum number of tamper alarm/restoral transmissions per zone. Valid entries: [000] to [014]. Program data [000]
to disable shutdown.
Swinger Shutdown (Trouble): Maximum number of trouble alarm/restoral transmissions per trouble condition. Valid entries: [000] to [014].
Program data [000] to disable shutdown.
Communicator (Transmission) Delay: Time, in seconds, panel will delay reporting an alarm event. Valid entries: [000] to [255].
AC Failure Communication Delay: Time, in minutes, panel will delay reporting an AC trouble event. Valid entries: [000] to [255].
TLM Trouble Delay: Time, in 3 second checks, before the system will consider the phone line disconnected. Valid entries: [002] to [255]
(e.g., 3 x10 seconds = 30 seconds).
TLM Restoral follows the same delay.
Test Transmission Cycle (Land Line): Number of days between test transmission reporting events. Valid entries: [001] to [255].
For Future Use
Wireless Zone Low Battery Delay: Number of days the system will delay reporting a wireless low battery to the central station.
Valid entries: [000] to [255]. Program data [000] for no delay.
Delinquency Transmission Delay: Number of hours (Activity Delinquency) or days (Arming Delinquency) the panel will delay before transmitting
the event to the central station. Valid entries: [001] to [255].
Communication Cancel Window: Time, in seconds, after an alarm has occurred that the system will report a Communication Cancel reporting event
if the system is disarmed. They keypad will beep rapidly to indicate the Communication Cancel reporting event has been communicated successfully.
Valid entries: [001] to [255].
Section [378] Test Transmission Time
Program the time the system will report a Test Transmission reporting event. Program 4 digits – [HH][MM] using military standard.
For a test transmission at 11:00 pm, program data [23][00]). Valid entries are [00][00] to [23][59].
19
PowerSeries - PC1616/PC1832/PC1864
Section [379] Periodic DLS Time of Day
Programs the time the system will auto-call DLS. Program 4 digits – [HH][MM] using military standard. For a DLS auto-call at 11:00 pm,
program data [23][00]). Valid entries are [00][00] to [23][59]. Programming [99][99] will select a random time, [FF][FF] will disable it.
Please refer to the PC 1616/1832/1864 Reference Manual for a complete description of Periodic DLS.
Section [380] First Communicator Option Code
Option
Description
[1]
ON: the system communicator is enabled. OFF: the communicator is disabled.
[2]
ON: the system transmits alarm restorals if the zone is restored and the bell has timed out. OFF: the system transmits alarm restorals
immediately when the zone is restored.
[3]
ON: the panel uses rotary (pulse) dialing. OFF: the panel uses touchtone (DTMF) dialing
[4]
ON: the panel will switch from touchtone dialing to rotary dialing after the 4th failed attempt to communicate.
OFF: the panel will use DTMF dialing for all dialing attempts.
[5]
ON: the system uses the Third Phone Number to back up the First Phone Number. OFF: the Third Phone Number is disabled.
[6]
ON: the system alternates between the First Phone Number and Third Phone Number when attempting to report an event.
OFF: the panel will dial the First Phone Number for the programmed number of attempts, then switch to the Third Phone Number.
[7]
For future Use
[8]
ON: the Delinquency feature follows zone activity. OFF: the Delinquency feature follows arming.
Section [381] Second Communicator Option Code
Option
Description
[1]
ON: the keypad beeps 8 times after successfully transmitting the Opening After Alarm reporting event. OFF: the keypad does not beep.
[2]
ON: the bell output squawks 8 times after successfully transmitting the Opening After Alarm reporting event. OFF: the bell output does
not activate.
[3]
ON: the system uses programmed reporting codes when transmitting using the SIA format.
OFF: the system automatically generates all reporting codes transmitted.
[4]
ON: the system beeps the keypad 8 times after successfully transmitting a Closing reporting event. OFF: the keypad does not beep.
[5]
ON: the system requests a Listen in/Two-way session the next time it calls the 1st/3rd Phone Number when the PC59xx transmits a
request. OFF: the system ignores the request from the PC59xx.
This Option is used with PC59xx series modules.
[6]
ON: the system requests a Listen in/Two-way session the next time it calls the 2nd Phone Number when the PC59xx transmits a request.
OFF: the system will ignore the request from the PC59xx.
This Option is used with PC59xx series modules.
[7]
ON: the system uses Contact ID format programmed reporting codes when transmitting reporting codes.
OFF: the system automatically generates all reporting codes transmitted.
[8]
ON: the system will follow ULC Communication Priority OFF: the system will follow standard communications priority.
Section [382] Third Communicator Option Code
Option
20
Description
[1]
ON: the system will use the digit [5] as the first digit of the Partial Closing reporting code when transmitting Contact ID reporting codes.
OFF: the system will use the digit [4] as the first digit of the Partial Closing reporting code when transmitting Contact ID reporting codes.
[2]
ON: the system will transmit all alarms during Walk Test. OFF: the system will not report alarm events during Walk Test.
Section 4 – Programming Descriptions
[3]
ON: the keypad will display the message ‘Communications Cancelled’ (programmable LCD) or ‘CC’ (fixed-message LCD) upon
successful transmission of the Communication Cancelled reporting event. OFF: the keypad will not display these messages.
[4]
ON: the system dials the Call Waiting Cancel String on the first attempt to dial the central station. OFF: the system does not dial the Call
Waiting Cancel String.
[5]
ON: enables support for the T-Link module. OFF: disables T-Link.
[6]
ON: the AC Failure Transmission Delay Timer will use hours. OFF: the delay will be in minutes.
[7]
ON: Sets the number of Dialing attempts to 1 when using Residential Dial Format. OFF: Residential Dial follows Dialing Attempt
Counter.
[8]
For Future Use
Section [383] Fourth Communicator Option Code
Option
[1]
[2-8]
Description
ON: Events programmed to communicate to phone #1 will use the Partition Account Number in section [311]. Events Programmed to
communicate to phone #2 will use the Partition Account Number in section [312]. OFF: Each events will use its respective partition
account code.
For Future Use
Section [389] T-Link Fault Check Timer
Program the period of time (in seconds) in between checks to see if the T-Link module is present. Valid entries are [001]-[255].
Section [401] First Downloading Option Code
Option
[1]
Description
ON: the system answers incoming calls for downloading (either Programmed Number of Rings or Double Call). OFF: the system does not
answer incoming calls using the double call routine for downloading.
These settings do not affect the 6 hour DLS downloading window on power up.
[2]
ON: the user can enable downloading for the DLS Window using the [ ][6] command. OFF: the user cannot enable downloading.
[3]
ON: the system will hang up after a successful DLS connection and call the computer back using the DLS Phone Number (Section [402]).
OFF: the system stays connected to the computer.
[4]
ON: the user can initiate a downloading session using the [ ][6] command. OFF: the user cannot initiate a downloading session.
[5]
ON: the system attempts to call the downloading computer after transmitting a Event Buffer 75% Full event to the central station. OFF: the
system does NOT call the downloading computer after transmitting this event.
[6]
ON: Panel communicates with DLS at 300 Baud. OFF: Panel communicates with DLS at 110 Baud.
[7]-[8]
For Future Use
Section [402] Downloading Computer Phone Number
The Downloading Computer Telephone Number is used for Call Back, User Initiated DLS and the Auto Event Buffer Upload functions.
Program the phone number as required. HEX digits can be included for special applications:
HEX [A]
HEX [B]
HEX [C]
HEX [D]
HEX [E]
HEX [F]
Not used
Simulates a [ ] key press
Simulates a [#] key press
Additional dial tone search
2-second pause
End of phone number marker
Section [403] Downloading Access Code
Program the 6-digit Downloading Access Code. Upon connection, the system will only connect to the downloading computer if the
Downloading Access Code programmed matches the Downloading Access Code programmed in the computer file.
21
PowerSeries - PC1616/PC1832/PC1864
Section [404] Panel Identification Code
Program the 6-digit Panel Identification Code. This code is used by the downloading computer to verify the correct account is calling back
(Call Back feature) or to identify which customer account file should be used (User Initiated DLS and Auto Event Buffer Upload features).
Section [405] Double-Call Timer
Program the maximum time, in seconds, between calls when connecting to panel using the double call feature. Valid entries are [000] to
[255].
Section [406] Number of Rings to Answer On
Program the number of consecutive rings that panel must detect to answer for downloading. Valid entries are [000] to [010].
Section [499] PC-Link Communications
Enter the following command to initiate downloading via PC-Link – Section [499] [Installer Code] [499]. Plugging in the PC-Link connector will automatically initiate the connection if DLS is initiated before connecting the PC-Link Header. The session will NOT be automatically initiated if the system is in installer mode.
Section [501] to [514] Programmable Output Attributes
These Sections are used to customize the operation of the PGM outputs (Section [501] for PGM 1, Section [502] for PGM 2 etc.). The available options depend on which PGM output type is programmed.
When the PGM Output Options (Section [009] to [011]) are programmed, the system will change the PGM Attributes to the default settings.
The PGM Attributes will default if a new PGM output option is programmed.
PGM Output Option [01], [03] to [08], [11] to [22], [25],[26], [28], [30], [33], [34]
Option
[3]
Description
ON: the PGM output will operate normally (switch to ground when activated). OFF: the PGM output will be normally ground and switch
to open collector (open circuit) when activated.
PGM Output Option [19] to [22]
Option
Description
[4]
ON: the PGM output will activate for the duration of the PGM Output Timer when the [ ][7][x] command is performed.
OFF: the PGM output will latch until the [ ][7][x] command is performed again.
[5]
ON: a valid user code must be entered after the [ ][7][x] command. OFF: user code is not required.
PGM Output Option [09]
Option
Description
[1]
ON: PGM output activates if a Service Required trouble condition is present.
[2]
ON: PGM output activates if an AC trouble condition is present.
[3]
ON: PGM output activates if a Telephone Line trouble condition is present.
[4]
ON: PGM output activates if a Failure to Communicate trouble condition is present.
[5]
ON: PGM output activates if a Zone Fault condition is present.
[6]
ON: PGM output activates if a Zone Tamper condition is present.
[7]
ON: PGM output will activates if a Wireless Low Battery trouble condition is present.
[8]
ON: PGM output will activates if a Loss of Clock trouble condition is present.
PGM Output Option [10]
Option
22
Description
[1]
ON: PGM output activates if a Burglary Alarm occurs.
[2]
ON: PGM output activates if a Fire Alarm occurs.
Section 4 – Programming Descriptions
[3]
ON: PGM output activates if a Panic Alarm occurs.
[4]
ON: PGM output activates if a Medical Alarm occurs.
[5]
ON: PGM output activates if a Supervisory Alarm occurs.
[6]
ON: PGM output activates if a Priority Alarm occurs.
[7]
ON: PGM output will activates if a 24-Hour Hold-Up Alarm occurs.
[8]
ON: the PGM output activates for the time programmed for the PGM Output Timer. OFF: the PGM output will latch until a valid user code
is entered.
PGM Output Option [31]
Option
Description
[1]
ON: PGM output activates if a Fire Alarm occurs.
[2]
ON: PGM output activates if a Panic Alarm occurs.
[3]
ON: PGM output activates if a Burglary Alarm occurs.
[4]
ON: PGM output activates if an Opening/Closing occurs.
[5]
ON: PGM output activates if a a zone is automatically bypassed.
[6]
ON: PGM output activates if a Medical Alarm occurs.
[7]
ON: PGM output will activates if a confirmed alarms occurs and Police Code occurs.
[8]
ON: the PGM output is active when the selected condition is true. OFF: the PGM output will latch until a valid user code is entered
PGM Output Option [32]
Option
[1]-[7]
[8]
Description
For Future Use
ON: the PGM will activate for the duration programmed in PGM Output Timer. OFF: the PGM will activate when an Opening After Alarm
occurs and will deactivate when a valid access code is entered.
PGM Output Option [29] and [35]-[41]
Option
[1]-[2]
[3]
[4]-[7]
[8]
Description
For Future Use
ON: the PGM will switch to ground when the event occurs. OFF: the PGM will switch to open when the event occurs.
For Future Use
ON: AND logic is selected, all zones that are enabled must be violated before the PGM will activate. OFF: OR Logic is selected, only one
violated zone is required to activate the PGM. All zones must be restored to turn it OFF.
Zones are assigned to this PGM in the PGM Partition Assignment Section [551]-[564]
Section [551] to [564] PGM Partition Assignment
These sections are used to customize the operation of the PGM outputs (Section [551] for PGM 1, Section [552] for PGM 2 etc.). Turn on the
correct option in the correct section to assign the PGM output to a specified partition. PGM outputs can be assigned to more than one partition. For PGM outputs that are considered ‘system’ outputs (e.g.,Trouble output), programming in these sections will not affect the operation
of the PGM output.For Zone Follower PGM types 29, 35-41 these sections are used to assign specific zones to the PGM.
Any one Command Output PGM type cannot be assigned to more then one partition.
23
PowerSeries - PC1616/PC1832/PC1864
Section [601] to [608] Additional Reporting Codes
Program the reporting code for all events to be transmitted. For description of when each reporting event will be transmitted, refer to
Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable
the reporting of an event. If any other data is programmed (Data [01] to [FF]) the panel will automatically generate the correct reporting
event when transmitting to the central station. For all formats excluding Automatic SIA and Automatic Contact ID, the panel will not attempt
to report an event if data [00] or data [FF] is programmed for the reporting code.
Section [681] to [688] Auto-Disarm Schedules
Program the time to auto-disarm (Section [681] for Partition 1, Section [682] for Partition 2 etc.) for each day of the week. Each Section has
seven, 4-digit entries, two digits for the hour, two digits for the minute, for Sunday through Saturday. Program using the military format (for
example, to auto arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto disarming
Section [691] to [698] Auto-Disarm Holiday Schedule
Program the dates to be used for Auto-Disarm holiday schedule (Section [691] for Partition 1, Section [692] for Partition 2 etc.) Each Section
has fourteen, 6-digit entries, two digits for the month, two digits for the day and two digits for the year.The panel will not disarm on the programmed dates. The format of entering the date is MMDDYY. Program [99][99][99] to disable Auto-Disarm holiday schedule.
Section [700] Automatic Clock Adjust
Program the number of seconds for the last minute of the day. This can be used to make minor corrections to the clock if the AC frequency is
not reliable. Valid entries are [01] to [99].
Section [701] First International Option Code
Option
Description
[1]
ON: configures the system for 50Hz AC. OFF: configures the system for 60Hz AC.
[2]
ON: the system uses the internal crystal for the internal panel clock. OFF: the system uses the AC frequency for the internal panel clock.
[3]
ON: the system will inhibit arming if a Low Battery or AC trouble condition is present. OFF: arming will not be inhibited.
[4]
ON: all Tamper troubles will latch and arming will be inhibited. Enter Installer Programming to clear the trouble condition and return to
normal operation. OFF: tamper troubles will not latch and will not inhibit arming.
[5]
ON: all access codes are 6 digits long. OFF: all access codes are 4 digits long.
[6]
ON: the system will hang up if a busy tone is detected. This attempt is not counted towards the Maximum Dialing Attempts programmed.
OFF: the panel will not detect busy tones.
[7]
ON: the system will charge the battery at approximately 700mA. OFF: the system will charge the battery at 400mA.
[8]
ON: the system will abort a DLS session, Escort access, Listen In/Two-way session if a new central station communication event occurs.
OFF: non-critical events (Test transmission, Periodic Test and System Test) will not abort the session. Events will be communicated after
the session is complete.
Section [702] Second International Option Code
Option
24
Description
[1]
ON: the communicator uses 33/67 make/break ratio when pulse dialing. OFF: the system uses 40/60 make/break ratio.
[2]
ON: the system dials regardless of the presence of dial tone after the first attempt. OFF: the system dials only if dial tone is detected.
[3]
ON: changes the Test Transmission Cycle Time to minutes. OFF: sends a Test Transmission after the programmed number of days.
[4]
ON: the system accepts 1600Hz handshake pulse formats. OFF: the system accepts 1400Hz or 2300Hz handshakes.
[5]
ON: the system generates a tone for 500mS every 2 seconds indicating digital equipment is making the call vs. a voice call.
OFF: the system does not generate a tone.
[6]
ON: the tone generated (2100Hz.) indicates that digital equipment is making the call. OFF: the tone is 1300Hz.
[7]
ON: the DLS down loading window is 1 hour. OFF: the DLS downloading window is 6 hours.
[8]
ON: the system activates the bell output if a Failure to Communicate trouble occurs while the system is armed.
OFF: the system does NOT activate the bell output if a Failure to Communicate trouble occurs while the system is armed.
Section 4 – Programming Descriptions
Section [703] Delay Between Dialing Attempts
Program the time the panel will wait between dialing attempts to transmit a reporting event to the central station.
Valid entries are [001] to [255].
Section [800]-[851] Module Programming
The following program sections are used to program different modules that can be connected to the control panel. Refer to the respective
Installation Manual for installation and programming information
Section [801]:
Section [802]:
Section [803]:
Section [804]:
Section [805]:
Section [851]:
PC5400 Printer Module Programming
PC59xx VOX Module Programming
Alternate Communicator Programming
Wireless Programming
PC5100 Addressable Programming
T-Link Programming
Special Installer Instructions
Section [899] Template Programming
Selecting [ ][8] [Installer Code] [899] displays the current 5 digit template programming code. Refer to Section 3.1 Template Programming on page 8 for details. Refer to Appendix C - Template Programming for a detailed description of available templates and corresponding 5 digit codes.
This feature requires a PK55xx or RFK55xx series keypad, v.1.1 or higher.
Section [900]: Panel Version Displayed
Only available with LCD5500 or PK5500 keypads. The system will display the version of the control panel (for example, [0410] indicates
panel version 4.10).
Section [901]: Installer Walk Test
The system will turn Installer Walk Test ON. The Ready, Armed and Trouble LED’s will flash rapidly while the test is active. Every time a
zone is violated the system will activate the bell output for two seconds and log the event to the event buffer. To turn Installer Walk Test OFF
enter Section [901] again. The system automatically terminates the test of there is no zone activity for 15 minutes.
Section [902]: Module Supervision Reset
All modules are automatically detected within one minute after being connected to the Keybus. Enter Section [902] to clear detected modules if a module is removed, if PC5108 jumpers are changed, or if a keypads slot assignments are programmed. The system will rescan the
Keybus to determine which modules are connected.
Section [903]: View Module Supervision
The keypad will display the modules detected by the system by turning on the associated zone light (LED keypads), flashing the numbers
(fixed-message LCD keypads) or displaying the modules detected in plain language (programmable LCD keypads). Refer to the chart below:
Indicator Light
(Zone)
Module
[01] to [08]
[09] to [14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[24]
[26] to [29]
Keypad in Slot #1 to #8
PC5108 Zone Expander #1 to #6
PC5100 Module
PC5108 Zone Expander #7
PC5132 Module or RFK keypad with integrated wireless receiver
PC5208
PC5204 Module
PC5400 Module
PC59xx Module
Alternate Communicator
Escort5580 or Escort5580TC
PC5200 #1 to #4
25
PowerSeries - PC1616/PC1832/PC1864
Section [904]: Wireless Placement Test
Enter Section [904] followed by the 2-digit number of the wireless zone to test. When a wireless signal is received from the selected transmitter, the system will indicate the location as Good or Bad as follows:
Good:
Bad:
One bell squawk, 1 keypad beep, keypad zone light [1] ON
Three bell squawks, 3 keypad beeps, keypad zone light [3] ON
Press [#] to exit when testing is complete. Enter the 2-digit zone number for the next wireless device to test or press [#] to return to standard
programming.
Section [990]: Installer Lockout Enable
Enter Section [990][Installer Code][990] to enable the Installer Lockout feature. A hardware default cannot be performed when the
Installer Lockout feature is ON. In addition, the system will chatter the line seizure relay 10 times if the panel is powered up to indicate the
feature is ON.
Section [991]: Installer Lockout Disable
Enter Section [991][Installer Code][991] to turn the Installer Lockout feature OFF.
Section [993] to [999]: Factory Default Module/Panel
The following Sections can be used to factory default a module or the main control panel. Enter the appropriate Section, followed by the
Installer Code, followed by the Section number (E.g., [993][Installer Code][993])
Section [993]:
Section [995]:
Section [996]:
Section [997]:
Section [998]:
Section [999]:
Factory Default Alternate Communicator
Factory Default Escort5580 Module
Factory Default Wireless Receiver
Factory Default PC5400 Module
Factory Default PC59xx Module
Factory Default Main Control Panel
Hardware Reset (Default) Main Control Panel
Perform the following to default the main control panel:
1. Power down the system completely.
2. Connect a short between Zone 1 and PGM1 on the control panel (remove all other wires form these terminals).
3. Power up the control panel (AC power only) for 10 full seconds.
4. Power down the control panel, remove short between Zone 1 and PGM1.
5. Power up the control panel.
26
Section 5: Programming Work Sheets
Section 5: Programming Work Sheets
5.1 Index to Programming Work Sheets
Programming Option
Page
[000] Keypad Enrollment .....................................................................28
[001]-[004] Zone Definitions................................................................28
[005] System Times.............................................................................29
[006] Installer’s Code...........................................................................30
[007] Master Code...............................................................................30
[008] Maintenance Code .....................................................................30
[009] PGM 1&2 Output Programming (Main Panel) ............................30
[010] PGM 3-10 Output Programming (Main Panel/PC5208) .............30
[011] PGM 11-14 Output Programming (PC5204) .............................30
[012] Keypad Lockout Options ............................................................30
[013] 1st System Options ....................................................................31
[014] 2nd System Options ...................................................................31
[015] 3rd System Options....................................................................31
[016] 4th System Options ....................................................................31
[017] 5th System Options ....................................................................32
[018] 6th System Options ....................................................................32
[019] 7th System Options ....................................................................32
[020] Keypad Zone Assignments ........................................................32
[021] 8th System Options ....................................................................33
[022] 9th System Options ....................................................................33
[023] 10th System Options ..................................................................33
[030] Zone Loop Response (Zones 1-8) .............................................33
[101] - [164] Zone Attributes ...............................................................34
[165] Maximum Dialing Attempts to Each Telephone Number ............36
[166] Post Dial Wait for Handshake (All Formats) ..............................36
[167] T-LINK Interface Communications Wait for Acknowledge ..........37
[168] Set Clock Forward (Daylight Saving Time) .................................37
[169] Set Clock Back (Standard Time) ................................................37
[170] PGM Output Timer .....................................................................37
[175] Auto-arm Postpone Timer ..........................................................37
[176] Cross Zone/Police Code Timer .................................................37
[181]-[188] Automatic Arming Schedule .............................................37
[190] No Activity Arming Pre-Alert Time..............................................37
[191]-[198] No Activity Arming Timers ................................................38
[199] Auto-arming Pre-Alert Timer .....................................................38
[201] Partition Selection Mask.............................................................38
[301] 1st Telephone Number (32 Digits) ..............................................39
[302] 2nd Telephone Number (32 Digits).............................................39
[303] 3rd Telephone Number (32 Digits) .............................................39
[304] Call Waiting Cancel String (6 Digits) ..........................................39
[310] System Account Code................................................................39
[311]-[318] Partition 1-8 Account Numbers.........................................39
[320]-[323] Alarm Reporting Codes, Zones 01-64 ..............................39
[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64................40
[328] Miscellaneous Alarm Reporting Codes ......................................40
[329] Priority Alarm and Restoral .......................................................40
[330]-[333] Tamper Reporting Codes, Zones 01-64............................40
[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64 .............41
[338] Miscellaneous Tamper Reporting Codes ...................................41
[339]-[340] Closing (Arming) Reporting Codes,
Access Codes 1-32.....................................................................41
[341] Miscellaneous Closing (Arming) Reporting Codes.....................41
[342]-[343] Opening (Disarming) Reporting Codes,
Access Codes 1-32.....................................................................41
[344] Miscellaneous Opening (Disarming) Reporting Codes ..............42
[345] Maintenance Alarm Reporting Codes ........................................42
[346] Maintenance Restoral Reporting Codes ..................................42
[347] Miscellaneous Maintenance Reporting Codes ...........................42
Programming Option
Page
[348] Test Transmission Reporting Codes ......................................... 42
[349] PC5700 Maintenance Reporting Codes ................................... 42
[350] Communicator Format Options ................................................. 43
[351]-[358] Alarm/Restore Communicator Call Directions.................. 43
[359]-[366] Tamper/Restore Communicator Call Directions ............... 43
[367]-[374] Opening/Closing Communicator Call Directions .............. 43
[375] System Maintenance Communicator Call Directions ................ 44
[376] System Test Transmissions Communicator Call Directions ....... 44
[377] Communication Variables .......................................................... 44
[378] Test Transmission Time of Day ................................................. 44
[379] Periodic DLS Time of Day.......................................................... 44
[380] 1st Communicator Options ........................................................ 44
[381] 2nd Communicator Options ....................................................... 45
[382] 3rd Communicator Options ........................................................ 45
[383] 4th Communicator Options ........................................................ 45
[401] DLS Downloading Option Codes ............................................... 45
[402] DLS Downloading Telephone Number (32 Digits) ..................... 46
[403]-[404] DLS Downloading Access Code / Panel ID Code ........... 46
[405] Answering Machine Double Call Timer ...................................... 46
[406] Number of Rings to Answer On ................................................. 46
[499] Initiate PC-Link Downloading..................................................... 46
[501]-[502] PGM 1&2 Output Attributes (Main Panel)......................... 47
[503]-[504] PGM 3&4 Output Attributes (Main Panel / PC5208)......... 47
[505]-[510] PGM 5-10 Output Attributes (5208).................................. 47
[511]-[515] PGM 11-14 Output Attributes (5204)................................ 47
[551]-[552] PGM 1&2 Output Partition Assignment (Main Panel)....... 48
[553]-[554] PGM 3&4 Output Partition Assignment
(Main Panel/PC5208) .......................................................................... 48
[555]-[560] PGM 5-10 Output Partition Assignment (5208)................ 48
[561]-[564] PGM 11-14 Output Partition Assignment (5204).............. 48
[601]-[604] Closing (Arming) Reporting Codes .................................. 48
[605]-[608] Opening (Disarming) Reporting Codes ............................ 49
[681]-[688] Automatic Disarming Schedule ........................................ 49
[691]-[698] Auto-Disarm Holiday Schedule ........................................ 49
[700] Automatic Clock Adjust ............................................................. 50
[701] 1st International Options ............................................................ 50
[702] 2nd International Options........................................................... 50
[703] Delay between Dialing Attempts ................................................ 50
[801] PC5400 Printer Module Programming ....................................... 51
[802] PC59xx VOX Programming........................................................ 51
[804] PC5132 Wireless Expansion Programming............................... 51
[805] PC5100 Programming ............................................................... 51
[851] T-LINK Programming.................................................................. 51
[899] Template Programming .............................................................. 51
[900] Panel Version Displayed ............................................................ 51
[901] Installer Walk Test Mode Enable/Disable .................................. 51
[902] Module Supervision Reset ....................................................... 51
[903] Module Supervision Field ........................................................ 51
[904] Wireless Module Placement Test ............................................. 51
[990] Installer Lockout Enable............................................................. 51
[991] Installer Lockout Disable ............................................................ 51
[993] Restore Alternate Communicator to Default Programming........ 51
[995] Restore Escort5580 to Default Programming ............................ 51
[996] Restore PC5132 to Default Programming.................................. 51
[997] Restore PC5400 to Default Programming.................................. 51
[998] Restore PC59xx to Default Programming .................................. 51
[999] Restore Control Panel to Default Programming ......................... 51
27
PowerSeries - PC1616/PC1832/PC1864
5.2 Programming Worksheets
Shaded programming sections indicate minimum programming requirements
SIA FAR CP-01 defaults are indicated in gray text.
Keypad Partition /Slot and Function Key Programming
[000] Keypad Enrollment
This must be done at each keypad requiring programming.
[0]
[1]
[2]
[3]
[4]
[5]
Slot address [Valid entries are 0-8 for the partition, 1-8 for the slot. (e.g., to enroll a keypad in partition 3 and slot 1, enter (31)]
Function Key 1 Assignment (Valid entries are 00-33)
Function Key 2 Assignment (Valid entries are 00-33)
Function Key 3 Assignment (Valid entries are 00-33)
Function Key 4 Assignment (Valid entries are 00-33)
Function Key 5 Assignment (Valid entries are 00-33)
Function Key Options:
00
01
02
03
04
05
06
07
08
09
10
Not used
Select Partition 1
Select Partition 2
Stay Arm
Away Arm
[*][9] No-Entry Arm
[*][4] Chime On / Off
[*][6][——][4] System Test
[*][1] Bypass Mode
[*][2] Trouble Display
[*][3] Alarm Memory
11 [*][5] Access Code Programming
12 [*][6] User Functions
13 Command Output #1 [*][7][1]
14 Command Output #2 [*][7][2]/Sensor Reset
15 Global Stay Arming
16 [*][0] Quick Exit
17 [*][1] Reactivate Stay/Away Zones
18 Global Away Arming
19 Command Output 3 [*][7][3]
20 For Future Use
21 Command Output 4 [*][7][4]
22 Global Disarming
23 Bypass Recall
24 Recall Bypass Group
25 For Future Use
26 Time and Date
27 Select Partition 3
28 Select Partition 4
29 Select Partition 5
30 Select Partition 6
31 Select Partition 7
32 Select Partition 8
33 Activate Local PGM
Partition/
Slot
[20] Zone
Assigned
Key 1
Key 2
Key 3
Key 4
Key 5
ICON / LED Defaults
11
00
03
04
06
14
16
Full Message Defaults
18
00
03
04
06
14
16
KEYPAD 1
00
KEYPAD 2
00
KEYPAD 3
00
KEYPAD 4
00
KEYPAD 5
00
KEYPAD 6
00
KEYPAD 7
00
KEYPAD 8
00
[001]-[004] Zone Definitions
00 Null Zone (Not Used)
01 Delay 1*
02 Delay 2*
03 Instant*
04 Interior*
05 Interior, Stay/Away*
06 Delay, Stay/Away*
07 Delayed 24 Hour Fire (Hardwired)**
08 Standard 24 Hour Fire (Hardwired)
09 24 Hour Supervisory
10 24 Hour Supervisory Buzzer*
11 24 Hour Burglary*
*For burglary applications only
28
12 24 Hour Holdup*
13 24 Hour Gas*
14 24 Hour Heating*
15 24 Hour Auxiliary*
16 24 Hour Panic*
17 24 Hour Emergency*
18 24 Hour Sprinkler*
19 24 Hour Water*
20 24 Hour Freeze*
21 24 Hour Latching Tamper*
22 Momentary Keyswitch Arm*
23 Maintained Keyswitch Arm*
** For residential fire applications only
25
26
29
30
31
32
35
36
37
87
88
Interior Delay*
24 Hour Non-alarm*
Auto Verified Fire
Fire Supervisory
Day Zone*
Instant Stay/Away*
24-hour Bell/Buzzer
24 Hour Non-Latching Tamper Zone
Night Zone
Delay 24 Hour Fire (Wireless/Addressable)**
Standard 24 Hour Fire (Wireless/Addressable)**
5.2 Programming Worksheets
Section
Zone
Def.
Section
Zone
Def.
Section
Zone
Def.
[001]
01
01
I_____I_____I
03
I_____I_____I
[002]
17
00
I_____I_____I
00
I_____I_____I
[003]
33
00
I_____I_____I
00
I_____I_____I
03
I_____I_____I
00
I_____I_____I
00
I_____I_____I
03
I_____I_____I
00
I_____I_____I
00
I_____I_____I
04
I_____I_____I
00
I_____I_____I
00
I_____I_____I
06
04
I_____I_____I
22
00
I_____I_____I
38
00
I_____I_____I
07
04
08
04
I_____I_____I
23
00
I_____I_____I
24
00
I_____I_____I
39
00
I_____I_____I
40
00
09
00
I_____I_____I
25
00
I_____I_____I
41
10
00
I_____I_____I
26
00
I_____I_____I
11
00
I_____I_____I
27
00
12
00
I_____I_____I
28
13
00
I_____I_____I
14
00
15
16
02
03
04
05
Section
Zone
Def.
[004]
49
00
I_____I_____I
50
00
I_____I_____I
51
00
I_____I_____I
52
00
I_____I_____I
53
00
I_____I_____I
54
00
I_____I_____I
I_____I_____I
55
00
I_____I_____I
I_____I_____I
56
00
I_____I_____I
00
I_____I_____I
57
00
I_____I_____I
42
00
I_____I_____I
58
00
I_____I_____I
I_____I_____I
43
00
I_____I_____I
59
00
I_____I_____I
00
I_____I_____I
44
00
I_____I_____I
60
00
I_____I_____I
29
00
I_____I_____I
45
00
I_____I_____I
61
00
I_____I_____I
I_____I_____I
30
00
I_____I_____I
46
00
I_____I_____I
62
00
I_____I_____I
00
I_____I_____I
31
00
I_____I_____I
47
00
I_____I_____I
63
00
I_____I_____I
00
I_____I_____I
32
00
I_____I_____I
48
00
I_____I_____I
64
00
I_____I_____I
18
19
20
21
34
35
36
37
[005] System Times
Valid entries for Entry Delay is between 030-255, valid entries for Exit Delay is between 045-255 for SIA CP-01.
[01] Partition 1 Entry/Exit times
[05] Partition 5 Entry/Exit times
I___I___I___I
Entry Delay 1
I___I___I___I
Entry Delay 1
030
030
I_0_I_3_I_0_I
Entry Delay 2
I_0_I_3_I_0_I
Entry Delay 2
045
045
I_0_I_6_I_0_I
Exit Delay
I_0_I_6_I_0_I
Exit Delay
120
120
[02] Partition 2 Entry/Exit times
I___I___I___I
Entry Delay 1
030
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_6_I_0_I
Exit Delay
120
[06] Partition 6 Entry/Exit times
I___I___I___I
Entry Delay 1
030
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_6_I_0_I
Exit Delay
120
[03] Partition 3 Entry/Exit times
I___I___I___I
Entry Delay 1
030
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_6_I_0_I
Exit Delay
120
[07] Partition 7 Entry/Exit times
I___I___I___I
Entry Delay 1
030
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_6_I_0_I
Exit Delay
120
[04] Partition 4 Entry/Exit times
I___I___I___I
Entry Delay 1
030
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_6_I_0_I
Exit Delay
120
[09] Bell Cut-Off Timer (All Partitions)
I___I___I___I
Enter 3 digits from 001-255
004
[08] Partition 8 Entry/Exit times
I___I___I___I
Entry Delay 1
030
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_6_I_0_I
Exit Delay
120
For SIA CP-01 compliant installations, the Exit Delay must be within the range of 045-255 seconds (Default 60 seconds). If the Exit
Delay is silent (Section 14, Option 6 or Stay Function Key Arming) the exit delay must be twice the programmed value but must not
exceed 255 seconds (i.e., 090-255 seconds).
For UL Installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds.
Exit Time Restart shall be disabled when the panel is used in combination with T-Link TL250/TL300.
29
PowerSeries - PC1616/PC1832/PC1864
[006] Installer’s Code
[007] Master Code
[008] Maintenance Code
Default
5555 I_______I_______I_______I_______I
Default
1234
Default
AAAA
I_______I_______I_______I_______I
I_______I_______I_______I_______I
Programmable Output Options
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
Residential Burglary and Fire Bell Output
18
For Future Use
19
Sensor Reset [*][7][2]
20
2 Wire Smoke Support (PGM 2 only)
21
System Armed Status
22
Ready To Arm
23
Keypad Buzzer Follow Mode
24
Courtesy Pulse
25
System Trouble Output (with Trouble options)
26
System Event [Strobe (with Event options)]
28
System Tamper (all sources: zones, keypad, modules)29
TLM and Alarm
30
Kissoff Output
31
Ground Start Pulse
32
Remote Operation (DLS-3 Support)
33
For Future Use
34
Stay Armed Status
36
Command Output #1 ([*][7][1])
37
Command Output #2 ([*][7][2])
38
Command Output #3 ([*][7][3])
39
Command Output #4 ([*][7][4])
40
24 Hour Silent Input
41
24 Hour Audible Input
Delayed Fire and Burglary Output
Battery Test Output
Holdup Output
Zone Follower Output (Zones 1-8)
Partition Status Alarm Memory
Alternate Communicator
Open After Alarm
Bell Status and Programming Access Output
Away Armed with no Zone Bypassed Status
17
Away Armed Status
Zone Follower Output (Zones 9-16)
35
Zone Follower Output (Zones 17-24
Zone Follower Output (Zones 25-32)
Zone Follower Output (Zones 33-40)
Zone Follower Output (Zones 41-48)
Zone Follower Output (Zones 49-56)
Zone Follower Output (Zones 57-64)
Output types [03] and
[20] cannot be used
together on the same
system.
[009] PGM1 and PGM2 Output Programming (Main Panel)
Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
PC1616 and PC1832 have 2 onboard PGMs (PGM 1 and 2). PC1864 has 4 onboard PGMs (PGM 1-4)
Default
Default
19 I_______I_______I PGM 1
10 I_______I_______I PGM 2
[010] PGM3 to PGM10 Output Programming (Main Panel/PC5208)
Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
Default
01
Default
PGM 3 (main panel/PC5208)*
01
I_______I_______I
PGM 7 (PC5208)
01
I_______I_______I
PGM 4 (main panel/PC5208)*
01
I_______I_______I
PGM 8 (PC5208)
01
I_______I_______I
PGM 5 (PC5208)
01
I_______I_______I
PGM 9 (PC5208)
01
I_______I_______I
PGM 6 (PC5208)
01
I_______I_______I
PGM 10 (PC5208)
These two sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on the PC5208. If you use
both the main panel and the PC5208 outputs, PGM3 will work the same as the first PC5208 output, and PGM4 will work the same as the second PC5208 output.
I_______I_______I
[011] PGM 11 to PGM 14 Output Programming (PC5204)
Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
Default
01
I_______I_______I
PGM 11
Default
01
I_______I_______I
PGM 13
01
I_______I_______I
PGM 12
01
I_______I_______I
PGM 14
Other System Options
[012] Keypad Lockout Options
If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.
Default
000
I_______I_______I_______I
Number of Invalid Codes Before Lockout (001-255 codes)
000
I_______I_______I_______I
Lockout Duration (001-255 minutes)
30
5.2 Programming Worksheets
[013] First System Options
Opt
Def
1
2
3
9
4
5
6
7
8
9
9
9
R
R
R
R
R
R
R
R
ON
Normally Closed Loops
Double End-of-line Resistors
Panel shows all Troubles when armed
Tampers/Faults do not show as open
Auto Arm Schedule in [*][6] and installers
Audible Exit Fault Enabled
Event Buffer Follows Swinger Shutdown
Temporal Three Fire Signal Enabled
OFF
9
9 R Single End-of-line Resistors
R End-of-line Resistors
R Panel shows only Fire Troubles when armed
9 R Tampers/Faults show as open
R Auto-arm Schedule in Installer Programming Only
R Audible Exit Fault Disabled
R Event Buffer Logs Events past Shutdown
9 R Standard Pulsed Fire Signal
[014] Second System Options
Opt
Def
1
R
R
R
R
R
9R
R
R
2
3
4
5
6
7
8
ON
OFF
9R
9R
Arm /Disarm Bell Squawk Disabled
No Bell Squawk On Exit Delay
Bell Squawk On Entry Delay
9R
9R
Bell Squawk On Trouble
9R
No Bell Squawk On Trouble
Audible Exit with Urgency
R
9R
9R
Silent Exit Delay
Arm /Disarm Bell Squawk Enabled
Bell Squawk During Auto-arm
Bell Squawk On Exit Delay
Exit Delay Termination Enabled
Residential Fire Bell is Continuous
No Bell Squawk During Auto-arm
No Bell Squawk On Entry Delay
Exit Delay Termination Disabled
Residential Fire Bell is Cut-off
[015] Third System Options
Opt
Def
1
9R
Fire Key Enabled
2
R
R
9R
R
R
9R
R
Panic Key Audible (Bell / Beeps)
3
4
5
6
7
8
ON
Quick Exit Enabled (ON for SIA CP-01)
OFF
9
9
Quick Arming Enabled (No Code Required)
Code Required for Bypassing
Master Code NOT Changeable (ON for SIA CP-01)
9
9
TLM Enabled
TLM Audible (Bell) when Armed
9
R
R
R
R
R
R
R
R
Fire Key Disabled
Panic Key Silent
Quick Exit Disabled
Quick Arming Disabled (Code Required)
NO Code Required for Bypassing
Master Code Changeable
TLM Disabled
TLM Trouble Beeps when Armed
[016] Fourth System Options
Opt
Def
ON
1
9 R AC Trouble Displayed
2
R Trouble Light Flashes if AC Fails
R Blank Keypad when Not Used
R Code required to remove Keypad Blanking
9 R Keypad Backlighting is Enabled
R Power Save Mode Enabled
R Bypass Status Displayed While Armed
R Keypad Tampers Enabled
3
4
5
6
7
8
OFF
9
9
9
9
9
9
R
R
R
R
R
R
R
R
AC Trouble NOT Displayed
Trouble Light does NOT follow AC Status
Keypad Blanking Disabled
No Code Required
Keypad Backlighting is Disabled
Power Save Mode Disabled
Bypass Status NOT Displayed While Armed
Keypad Tampers Disabled
31
PowerSeries - PC1616/PC1832/PC1864
[017] Fifth System Options
Opt
Def
1
9 R
2
R
R
R
R
R
R
R
3
4
5
6
7
8
ON
OFF
WLS Key Does NOT use Access Codes
RF Jam Log after 5 Minutes
Audible RF Jam Trouble Beeps
Double Hit Enabled
Late to Close Enabled
Daylight Savings Time Enabled
For Future Use
Squawk on Away Key Arming/Disarming Only
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
WLS Key Uses Access Codes
RF Jam Log after 30 Seconds
Silent RF Jam Trouble Beeps
Double Hit Disabled
Late to Close Disabled
Daylight Savings Time Disabled
Squawk on all Arming/Disarming
[018] Sixth System Options
Opt
Def
R
R
R
R
R
R
R
R
1
2
3
4
5
6
7
8
ON
OFF
Test Transmission Exception Enabled
For Future Use
For Future Use
For Future Use
Keypad Buzzer Follows Bell Enabled
Cross Zoning Enabled
Exit Delay Restart Enabled (Enabled for SIA CP-01)
AC Trouble Beeps Enabled
9
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
Test Transmission Exception Disabled
Keypad Buzzer Follows Bell Disabled
Police Code Enabled
Exit Delay Restart Disabled
AC Trouble Beeps Disabled
[019] Seventh System Options
Opt
Def
ON
OFF
R
R Troubles are Latching
R First Zone in Alarm Enabled
R For Future Use
R For Future Use
R Green Keypad LED Power Indication
R [4][6] Accessable by All Users
R For Future Use
For Future Use
1
2
3
4
5
6
7
8
9
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
Troubles follow restore
First Zone in Alarm Disabled
Ready Indication
Master Code Only
Keypad Zone Assignments
[020] Keypad Zone Assignments
Only one keypad may be assigned to a zone.
Default
00
00
00
00
00
00
00
00
32
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
Keypad (slot 1) Zone
Keypad (slot 2) Zone
Keypad (slot 3) Zone
Keypad (slot 4) Zone
Keypad (slot 5) Zone
Keypad (slot 6) Zone
Keypad (slot 7) Zone
Keypad (slot 8) Zone
Only one keypad may be
assigned to a slot. Only one
zone can be assigned to a
keypad. Valid entries are
from 01 to 64.
5.2 Programming Worksheets
[021] Eighth System Options
Opt
Def
ON
OFF
1
R Access Code Entry Blocked During Entry Delay
9 R Access Code Entry Not Blocked During Entry Delay
2
R For Future Use
R For Future Use
R For Future Use
R For Future Use
R Keyswitch Disarming During Entry Delay Only
R For Future Use
R For Future Use
9
9
9
9
9
9
9
R
R
R
R
R
R
R
9
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
No Access Code Req’d for [4][1], [4][2], [4][3]
9
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
Fire Key Beeps and Sounds Bell
3
4
5
6
7
8
Keyswitch Disarming at Any Time
[022] Ninth System Options
Opt
1
2
3
4
5
6
7
8
Def
ON
R
R For Future Use
R For Future Use
R Master Code Bypasses Holdup Zones Only
R For Future Use
R RF Delinquency enabled
R For Future Use
R Audible Exit Delay for Stay Arming
Access Code Req’d for [4][1], [4][2], [4][3]
OFF
Any Code Bypasses Holdup Zones
RF Delinquency disabled
Stay Arming Silent
[023] Tenth System Options
Opt
1
2
3
4
5
6
7
8
Def
ON
R
R 200 Baud Open/Close Identifier Toggle ON
R Test Transmission While Armed Only
R Test Transmission in Hours
R Switching from AWAY to STAY disabled
R 2-way Audio will NOT Disconnect for a New Event
R Trouble Beeps are Silent*
R Keyswitch Arm in Away Mode
Fire Key Beeps Only
OFF
200 Baud Open/Close Identifier Toggle OFF
Test Transmission While Armed/Disarmed
Test Transmission in Days
AWAY to STAY toggle Option Permitted
2-way Audio Will Disconnect for a New Event
Trouble Beeps Sound Every 10 Seconds
Keyswitch arms in STAY or AWAY
* This option must be off for UL residential fire applications
[030] Zone Loop Response (Zones 1-8)
Opt
1
2
3
4
5
6
7
8
Def
R
R
R
R
R
R
R
R
ON
Zone 1 is Fast Loop Response
Zone 2 is Fast Loop Response
Zone 3 is Fast Loop Response
Zone 4 is Fast Loop Response
Zone 5 is Fast Loop Response
Zone 6 is Fast Loop Response
Zone 7 is Fast Loop Response
Zone 8 is Fast Loop Response
OFF
9
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
Zone 1 is Normal Loop Response
Zone 2 is Normal Loop Response
Zone 3 is Normal Loop Response
Zone 4 is Normal Loop Response
Zone 5 is Normal Loop Response
Zone 6 is Normal Loop Response
Zone 7 is Normal Loop Response
Zone 8 is Normal Loop Response
33
PowerSeries - PC1616/PC1832/PC1864
[101]-[164] Zone Attributes
Zone Attribute Defaults (Y = Option ON; N = Option OFF): Bold entries are opposite for SIA CP-01
Attribute:
ON
OFF
1
2
3
4
5
6
7
8
9
Audible
Silent
Steady
Pulsed
Chime
No
Bypass
No
Force*
No
Swing
No
Tx. Delay
No
Wireless Zn
No
Cross Zn
No
N
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Y
N
Y
N
Y
Y
Y
N
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
N
N
Y
N
N
N
Y
Y
Y
Y
Y
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
Y
Y
Y
N
Y
N
N
N
N
N
N
N
Y
Y
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
Y
N
N
Y
N
N
N
Y
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
Y
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Zone Type:
00 Null Zone
01 Delay 1
02 Delay 2
03 Instant
04 Interior
05 Int. Stay/Away
06 Dly. Stay/Away
07 Dly. 24hr Fire (Hardw.)
08 Stand. 24hr Fire (Hardw.)
09 24hr Superv.
10 24hr Superv. Buzzer
11 24hr Burglary
12 24hr Holdup
13 24hr Gas
14 24hr Heating
15 24hr Medical
16 24hr Panic
17 24hr Emergency
18 24hr Sprinkler
19 24hr Water
20 24hr Freeze
21 24hr Latching Tamper
22 Momentary Keyswitch
23 Maintained Keyswitch
25 Interior Delay
26 24hr Non-alarm
29 Auto Verified Fire
30 Fire Supervisory
31 Day Zone
32 Instant Stay/Away
35 24 hr Bell/Buzzer
36 24hr Non Latching Tamper
37 Night Zone
87 Dly. 24hr Fire (Wireless)
88 Stand. 24hr Fire (Wireless)
* For UL installations, do not change attribute 5 (Force Arming) from the default setting.
Attribute:
10
ON
OFF
Zone Type:
00 Null Zone
01 Delay 1
02 Delay 2
03 Instant
04 Interior
05 Int. Stay/Away
06 Dly. Stay/Away
07 Dly. 24hr Fire (Hardw.)
08 Stand. 24hr Fire (Hardw.)
09 24hr Superv.
10 24hr Superv. Buzzer
11 24hr Burglary
12 24hr Holdup
13 24hr Gas
14 24hr Heating
15 24hr Medical
16 24hr Panic
34
11
12
13
Zone Attributes 10-13 For Future Use
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
14
15
16
NC Loops
Config.
SEOL
Config.
DEOL
Config.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
5.2 Programming Worksheets
Attribute:
10
ON
OFF
17 24hr Emergency
18 24hr Sprinkler
19 24hr Water
20 24hr Freeze
21 24hr Latching Tamper
22 Momentary Keyswitch
23 Maintained Keyswitch
25 Interior Delay
26 24hr Non-alarm
29 Auto Verified Fire
30 Fire Supervisory
31 Day Zone
32 Instant Stay/Away
35 24 hr Bell/Buzzer
36 24hr Non Latching Tamper
37 Night Zone
87 Dly. 24hr Fire (Wireless)
88 Stand. 24hr Fire (Wireless)
Section
Zone #
Zone
Type**
11
12
13
14
15
16
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NC Loops
Config.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
SEOL
Config.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DEOL
Config.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Zone Attributes 10-13 For Future Use
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Audible/
Silent
1
Steady/
Pulsed
2
Chime
No
3
Bypass
No
4
Force*
No
5
Swing
No
6
Tx. Delay
No
7
Wireless
No
8
Cross Zn
No
9
[101]
[102]
[103]
[104]
[105]
[106]
[107]
[108]
[109]
[110]
[111]
[112]
[113]
[114]
[115]
[116]
[117]
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
(
(
(
(
(
(
(
(
(
(
(
(
(
(
(
(
(
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[118]
18
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[119]
19
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[120]
20
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[121]
21
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[122]
22
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[123]
23
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[124]
24
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[125]
25
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[126]
26
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[127]
27
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[128]
28
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[129]
29
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[130]
30
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[131]
31
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[132]
32
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[133]
33
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
35
PowerSeries - PC1616/PC1832/PC1864
Section
Zone #
Zone
Type**
Audible/
Silent
1
Steady/
Pulsed
2
Chime
No
3
Bypass
No
4
Force*
No
5
Swing
No
6
Tx. Delay
No
7
Wireless
No
8
Cross Zn
No
9
[134]
34
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[135]
35
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[136]
36
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[137]
37
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[138]
38
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[139]
39
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[140]
40
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[141]
41
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[142]
42
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[143]
43
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[144]
44
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[145]
45
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[146]
46
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[147]
47
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[148]
48
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[149]
[150]
[151]
[152]
[153]
[154]
[155]
[156]
[157]
[158]
[159]
[160]
[161]
[162]
[163]
[164]
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
(
(
(
(
(
(
(
(
(
(
(
(
(
(
(
(
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
NC Loops
Config.
14
SEOL
Config.
15
DEOL
Config.
16
Section
Zone #
Zone
Type**
For Future For Future For Future For Future
Use
Use
Use
Use
10
11
12
13
[101]
01
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
[102]
02
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
[103]
03
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
[104]
04
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
[105]
05
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
[106]
06
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
[107]
07
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
[108]
08
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
Zone attributes 10-16 only apply to zones 1-8.
System Timers
[165] Maximum Dialing Attempts to Each Telephone Number
Default 005
I_______I_______I_______I
Valid entries are 001-005 attempts
For UL Listed Installations, 5-10 dialing attempts are required.
[166] Post Dial Wait for Handshake (All Formats)
Default 040
36
I_______I_______I_______I
Valid entries are 001-255 seconds
5.2 Programming Worksheets
[167] T-LINK Interface Communications Wait for Acknowledge
Default 020
I_______I_______I_______I
Valid entries are 001-255 seconds
[168] Set Clock Forward (Daylight Saving Time)
Def 003
Month
|_______|_______|_______|
Valid Entries 001-012
Def 002
Week
|_______|_______|_______|
Valid Entries 000-005
Def 000
Day
|_______|_______|_______|
Valid Entries 001-031
Def 002
Hour
|_______|_______|_______|
Valid Entries 000-022
Def 001
Increment
|_______|_______|_______|
Valid Entries 001-002
[169] Set Clock Back (Standard Time)
Def 011
Month
|_______|_______|_______|
Valid Entries 001-012
Def 001
Week
|_______|_______|_______|
Valid Entries 000-005
Def 000
Day
|_______|_______|_______|
Valid Entries 001-031
Def 002
Hour
|_______|_______|_______|
Valid Entries 000-023
Def 001
Decrement |_______|_______|_______|
Valid Entries 001-002
[170] PGM Output Timer
Default 005
I_______I_______I_______I
Valid entries are 001-255 seconds
[171] Tamper PGM Output Timer
Default 000
I_______I_______I_______I
Valid entries are 000-255 minutes
[175] Auto-arm Postpone Timer
Default 000
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 disables automatic arming
[176] Cross Zone/Police Code Timer
Default 060
I_______I_______I_______I
Valid entries are 001-255 seconds/minutes
Automatic Arming Schedule
Enter a four-digit number (HH:MM) for each day that the system will Auto-arm on each partition (Section [181] for Partition 1
through section [188] for Partition 8). All entries are disabled (9999) by default. Valid entries are 0000-2359.
Sunday
[181]
[182]
[183]
[184]
[185]
[186]
[187]
[188]
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[190] No Activity Arming Pre-Alert Time
Default
Partition
001
All
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 for no pre-alert
37
PowerSeries - PC1616/PC1832/PC1864
No Activity Arming Timers - Default is [000] for all partitions
Section
Partition
[191]
[192]
[193]
[194]
[195]
[196]
[197]
[198]
1
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
2
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
3
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
4
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
5
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
6
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
7
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
8
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
[199] Auto-arming Pre-Alert Timer
Default: 004
I_______I_______I_______I
Valid entries are 001-255 minutes
Partition Programming
[201] Partition Selection Mask
Opt
1
2
3
4
5
6
7
8
Def
ON
OFF
9 R Partition 1 is enabled
R
R
R
R
R
R
R
Partition 2 is enabled
Partition 3 is enabled
Partition 4 is enabled
Partition 5 is enabled
Partition 6 is enabled
Partition 7 is enabled
Partition 8 is enabled
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
Cannot be disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
For the PC1864 and PC1832 Default is partition 1, zones 1-16 ON .
For the PC1616 Default is partition 1, zones 1-6 ON
Partition 1 Zone Assignment
Partition 2 Zone Assignment
Partition 3 Zone Assignment
Partition 4 Zone Assignment
[202] 1-8
RRRRRRRR [210] 1-8
RRRRRRRR [218] 1-8
RRRRRRRR [226] 1-8
RRRRRRRR
[203] 9-16
RRRRRRRR [211] 9-16
RRRRRRRR [219] 9-16
RRRRRRRR [227] 9-16
RRRRRRRR
[204] 17-24 RRRRRRRR [212] 17-24 RRRRRRRR [220] 17-24 RRRRRRRR [228] 17-24 RRRRRRRR
[205] 25-32 RRRRRRRR [213] 25-32 RRRRRRRR [221] 25-32 RRRRRRRR [229] 25-32 RRRRRRRR
[206] 33-40 RRRRRRRR [214] 33-40 RRRRRRRR [222] 33-40 RRRRRRRR [230] 33-40 RRRRRRRR
[207] 41-48 RRRRRRRR [215] 41-48 RRRRRRRR [223] 41-48 RRRRRRRR [231] 41-48 RRRRRRRR
[208] 49-56 RRRRRRRR [216] 49-56 RRRRRRRR [224] 49-56 RRRRRRRR [232] 49-56 RRRRRRRR
[209] 57-64 RRRRRRRR [217] 57-64 RRRRRRRR [225] 57-64 RRRRRRRR [233] 57-64 RRRRRRRR
Partition 5 Zone Assignment
Partition 6 Zone Assignment
Partition 7 Zone Assignment
Partition 8 Zone Assignment
[234] 1-8
RRRRRRRR [242] 1-8
RRRRRRRR [250] 1-8
RRRRRRRR [258] 1-8
RRRRRRRR
[235] 9-16
RRRRRRRR [243] 9-16
RRRRRRRR [251] 9-16
RRRRRRRR [259] 9-16
RRRRRRRR
[236] 17-24 RRRRRRRR [244] 17-24 RRRRRRRR [252] 17-24 RRRRRRRR [260] 17-24 RRRRRRRR
[237] 25-32 RRRRRRRR [245] 25-32 RRRRRRRR [253] 25-32 RRRRRRRR [261] 25-32 RRRRRRRR
[238] 33-40 RRRRRRRR [246] 33-40 RRRRRRRR [254] 33-40 RRRRRRRR [262] 33-40 RRRRRRRR
[239] 41-48 RRRRRRRR [247] 41-48 RRRRRRRR [255] 41-48 RRRRRRRR [263] 41-48 RRRRRRRR
[240] 49-56 RRRRRRRR [248] 49-56 RRRRRRRR [256] 49-56 RRRRRRRR [264] 49-56 RRRRRRRR
[241] 57-64 RRRRRRRR [249] 57-64 RRRRRRRR [257] 57-64 RRRRRRRR [265] 57-64 RRRRRRRR
38
5.2 Programming Worksheets
Communications
[301] First Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
When using T-Link,
program DCAA as
the phone number.
[302] Second Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[303] Third Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[304] Call Waiting Cancel String (6 Digits) - This feature is activated in Section 382 Opt 4
I_______I_______I_______I_______I_______I_______I
Default = DB70EF Program unused digits with Hex F
All six digits must be entered for changes to be saved. Fill unused digit spaces with ‘F’.
Account Codes
Enter a 6-digit account number for the system account code. SIA will use this account code for all eight partitions. Only SIA supports 6-digit account codes. If the last two digits of the account code are FF, the panel will only use the first four digits.
Section [310] System Account Code DEF [FFFFFF]
I_______I_______I_______I_______I_______I_______I
Enter a four-digit account number for each active partition.
[311] Partition 1 Account Number
|_______I_______I_______I_______I
[312] Partition 2 Account Number
|_______I_______I_______I_______I
[313] Partition 3 Account Number
|_______I_______I_______I_______I
[314] Partition 4 Account Number
|_______I_______I_______I_______I
[315] Partition 5 Account Number
|_______I_______I_______I_______I
[316] Partition 6 Account Number
|_______I_______I_______I_______I
[317] Partition 7 Account Number
|_______I_______I_______I_______I
[318] Partition 8 Account Number
|_______I_______I_______I_______I
All Account Numbers codes are defaulted to FFFF.
Reporting Codes
[320]-[323] Alarm Reporting Codes, Zones 01-64
All Reporting Codes defaulted to FF unless otherwise indicated.
Section
[320]
[321]
[322]
[323]
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 33
Zone 34
Zone 35
Zone 36
Zone 37
Zone 38
Zone 39
Zone 40
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 41
Zone 42
Zone 43
Zone 44
Zone 45
Zone 46
Zone 47
Zone 48
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 49
Zone 50
Zone 51
Zone 52
Zone 53
Zone 54
Zone 55
Zone 56
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 57
Zone 58
Zone 59
Zone 60
Zone 61
Zone 62
Zone 63
Zone 64
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
39
PowerSeries - PC1616/PC1832/PC1864
[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64
Section
[324]
[325]
[326]
[327]
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 33
Zone 34
Zone 35
Zone 36
Zone 37
Zone 38
Zone 39
Zone 40
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 41
Zone 42
Zone 43
Zone 44
Zone 45
Zone 46
Zone 47
Zone 48
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 49
Zone 50
Zone 51
Zone 52
Zone 53
Zone 54
Zone 55
Zone 56
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 57
Zone 58
Zone 59
Zone 60
Zone 61
Zone 62
Zone 63
Zone 64
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
[328] Miscellaneous Alarm Reporting Codes
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Duress Alarm
Opening After Alarm
Recent Closing
Zone Expander Supervisory Alarm
Zone Expander Supervisory Restore
Cross Zone Police Code Alarm
Burglary Not Verified
Alarm Cancelled
[329] Priority Alarm and Restoral
I_______I_______I
Keypad Fire Alarm
I_______I_______I
Keypad Auxiliary Alarm
I_______I_______I
Keypad Panic Alarm
I_______I_______I
Auxiliary Input Alarm
I_______I_______I
Keypad Fire Restoral
I_______I_______I
Keypad Auxiliary Restoral
I_______I_______I
Keypad Panic Restoral
I_______I_______I
Auxiliary Input Restore
[330]-[333] Tamper Reporting Codes, Zones 01-64
Section
[330]
[331]
[332]
[333]
40
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 33
Zone 34
Zone 35
Zone 36
Zone 37
Zone 38
Zone 39
Zone 40
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 41
Zone 42
Zone 43
Zone 44
Zone 45
Zone 46
Zone 47
Zone 48
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 49
Zone 50
Zone 51
Zone 52
Zone 53
Zone 54
Zone 55
Zone 56
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 57
Zone 58
Zone 59
Zone 60
Zone 61
Zone 62
Zone 63
Zone 64
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
5.2 Programming Worksheets
[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64
Section
[334]
[335]
[336]
[337]
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 33
Zone 34
Zone 35
Zone 36
Zone 37
Zone 38
Zone 39
Zone 40
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 41
Zone 42
Zone 43
Zone 44
Zone 45
Zone 46
Zone 47
Zone 48
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 49
Zone 50
Zone 51
Zone 52
Zone 53
Zone 54
Zone 55
Zone 56
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 57
Zone 58
Zone 59
Zone 60
Zone 61
Zone 62
Zone 63
Zone 64
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 6
Code 7
Code 8
I_______I_______I
[338] Miscellaneous Tamper Reporting Codes
I_______I_______I General System Tamper
I_______I_______I
General System Tamper Rest.
I_______I_______I
Keypad Lockout
[339]-[340] Closing (Arming) Reporting Codes, Access Codes 1-32
Section
[339]
Code 1
Code 2
Code 3
Code 4
Code 5
[340]
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 17
Code 18
Code 19
Code 20
Code 21
Code 22
Code 23
Code 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 25
Code 26
Code 27
Code 28
Code 29
Code 30
Code 31
Code 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 6
Code 7
Code 8
[341] Miscellaneous Closing (Arming) Reporting Codes
I_______I_______I For Future Use
I_______I_______I
For Future Use
I_______I_______I
For Future Use
I_______I_______I
For Future Use
I___0___I___0___I
Automatic Zone Bypass
I_______I_______I
Partial Closing
I_______I_______I
Special Closing
I_______I_______I
Late to Close
I_______I_______I
Exit Fault
[342]-[343] Opening (Disarming) Reporting Codes, Access Codes 1-32
Section
[342]
Code 1
Code 2
Code 3
Code 4
Code 5
[343]
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 17
Code 18
Code 19
Code 20
Code 21
Code 22
Code 23
Code 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 25
Code 26
Code 27
Code 28
Code 29
Code 30
Code 31
Code 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
41
PowerSeries - PC1616/PC1832/PC1864
[344] Miscellaneous Opening (Disarming) Reporting Codes
I_______I_______I
For Future Use
I_______I_______I
For Future Use
I_______I_______I
For Future Use
I_______I_______I
For Future Use
I_______I_______I
For Future Use
I_______I_______I
Auto Arm Cancellation/Postpone
I_______I_______I
Special Opening
[345] Maintenance Alarm Reporting Codes
[346] Maintenance Restoral Reporting Codes
I_______I_______I
Battery Trouble Alarm
I_______I_______I
Battery Trouble Restoral
I_______I_______I
AC Failure Trouble Alarm
I_______I_______I
AC Failure Trouble Restoral
I_______I_______I
Bell Circuit Trouble Alarm
I_______I_______I
Bell Circuit Trouble Restoral
I_______I_______I
Fire Trouble Alarm
I_______I_______I
Fire Trouble Restoral
I_______I_______I
Auxiliary Power Supply Trouble Alarm
I_______I_______I
Auxiliary Power Supply Trouble Restoral
I_______I_______I
TLM Trouble Code
I_______I_______I
TLM Restoral
I_______I_______I
General System Trouble
I_______I_______I
General System Trouble Restoral
I_______I_______I
General System Supervisory
I_______I_______I
General System Supervisory Restoral
[347] Miscellaneous Maintenance Reporting Codes
[348] Test Transmission Reporting Codes
I_______I_______I
Telephone Number 1 FTC Restore
I_______I_______I
Walk Test End
I_______I_______I
Telephone Number 2 FTC Restore
I_______I_______I
Walk Begin
I_______I_______I
Event Buffer 75% Full Since Last Upload
I_______I_______I
Periodic Test Transmission with Trouble
I___0___I___0___I
DLS Lead IN
I_______I_______I
Periodic Test Transmission
I___0___I___0___I
DLS Lead OUT
I_______I_______I
System Test
I_______I_______I
Zone Fault Alarm
I_______I_______I
For Future Use
I_______I_______I
Zone Fault Restore
I_______I_______I
Delinquency Code
I_______I_______I
General Zone Low Battery Alarm
I_______I_______I
General Zone Low Battery Restoral
I__0____I___0___I
Installer Lead Out
I___0___I___0___I
Installer Lead In
[349] PC5700 Maintenance Reporting Codes
The PC5700 is available in Canada only.
I_______I_______I
PC5700 Ground Fault Trouble
I_______I_______I
PC5700 Ground Fault Restore
I_______I_______I
PC5700 TLM Line 1 Trouble
I_______I_______I
PC5700 TLM Line 1 Restore
I_______I_______I
PC5700 TLM Line 2 Trouble
I_______I_______I
PC5700 TLM Line 2 Restore
42
5.2 Programming Worksheets
[350] Communicator Format Options
Default
04 I_______I_______I1st Telephone Number
04I_______I_______I2nd Telephone Number
01 20 BPS, 1400 HZ handshake
05 Pager
08 10 BPS, 2300Hz handshake 11 For Future Use
02 20 BPS, 2300 HZ handshake
06 Residential Dial**
09 Private Line
03 DTMF CONTACT ID
07 10 BPS, 1400Hz handshake 10 Scantronics
04 SIA FSK
**Failure to communicate using Residential Dial will not generate a Failed To Communicate Trouble.
12 For Furure Use
13 CESA 200
Call Direction Options
[351]-[358] Alarm/Restore Communicator Call Directions
Section Partition
[351]
[352]
[353]
[354]
[355]
[356]
[357]
[358]
1
2
3
4
5
6
7
8
Option 2
Option 1
2nd Telephone
1st Telephone
Number (Def ON) Number (Def OFF)
Option 3
Not Used
(Def OFF)
Option 4
Not Used
(Def OFF)
Option 5
Alt Comm
(Def ON)
Options 6,7,8
Future Use
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
[359]-[366] Tamper/Restore Communicator Call Directions
Option 2
Option 1
2nd Telephone
Section Partition 1st Telephone
Number (Def ON) Number (Def OFF)
Option 3
Not Used
(Def OFF)
Option 4
Not Used
(Def OFF)
Option 5
Alt Comm
(Def ON)
Options 6,7,8
Future Use
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
[359]
[360]
[361]
[362]
[363]
[364]
[365]
[366]
1
2
3
4
5
6
7
8
[367]-[374] Opening/Closing Communicator Call Directions
Section Partition
[367]
[368]
[369]
[370]
[371]
[372]
[373]
[374]
1
2
3
4
5
6
7
8
Option 2
Option 1
2nd Telephone
1st Telephone
Number (Def OFF) Number (Def OFF)
Option 3
Not Used
(Def OFF)
Option 4
Not Used
(Def OFF)
Option 5
Alt Comm
(Def OFF)
Options 6,7,8
Future Use
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
43
PowerSeries - PC1616/PC1832/PC1864
[375] System Maintenance Communicator Call Directions
Option 2
Option 1
2nd Telephone
1st Telephone
Number (Def ON) Number (Def OFF)
Section
I________I
[375]
Option 3
Not Used
(Def OFF)
Option 4
Not Used
(Def OFF)
Option 5
Alt Comm
(Def ON)
Options 6,7,8
Future Use
I________I
I________I
I________I
I________I
Option 3
Not Used
(Def OFF)
Option 4
Not Used
(Def OFF)
Option 5
Alt Comm
(Def ON)
Options 6,7,8
Future Use
I________I
I________I
I________I
I________I
I________I
[376] System Test Transmissions Communicator Call Directions
Option 2
Option 1
2nd Telephone
1st Telephone
Number (Def ON) Number (Def OFF)
Section
I________I
[376]
I________I
[377] Communication Variables
Default
003
I___0__I__0__I___1__I
Swinger Shutdown (Alarms and Rest)
001-014 Transmissions
003
I___0__I__0__I___3__I
Swinger Shutdown (Tampers and Rest)
001-014 Transmissions, 000=disabled
003
I___0__I__0__I___3__I
Swinger Shutdown (Maint and Rest)
001-014 Transmissions, 000=disabled
000
I___0__I__3__I___0__I
Communication Delay
000-255 seconds
030
I___0__I__3__I___0__I
AC Failure Communication Delay
001-255 minutes, 000=disabled
010
I___0__I__1__I___0__I
TLM Trouble Delay
No. of checks required - valid entries 002 - 255)
001-255 days/minutes†
030
I___0__I__3__I___0__I
Test Transmission Cycle (land line)
030
I___0__I__3__I___0__I
For Future Use
007
I___0__I__0__I___7__I
Zone Low Battery Transmission Delay
000-255 days
030
I___0__I__3__I___0__I
Delinquency Transmission Cycle
001-255 days/hours
000
I___0__I__0__I___5__I
Communications Cancelled Window
001-255 minutes
†Dependent on programming in section [702], option [3].
The values in gray GRAY are required for CP-01 compliant systems
For UL installations, the Entry Delay plus Communication Delay time must not exceed 60 seconds.
[378] Test Transmission Time of Day
Default
9999
I_______I_______I_______I_______I Valid
entries are 0000-2359 (9999 to disable)
[379] Periodic DLS Time of Day
Default
9999
I_______I_______I_______I_______I Valid
entries are 0000-2359 (9999 for Random, FFFF to disable)
[380] First Communicator Options
Opt
Def
ON
OFF
1
9 R Communications Enabled
2
R Restorals on Bell Time-out
9 R Restorals Follow Zones
3
R Pulse Dialing
9 R DTMF Dialing
4
R Switch to Pulse Dialing on 5th Attempt
9 R DTMF Dial For All Attempts
5
R 3rd Telephone Number Enabled
9 R 3rd Telephone Number Disabled
6
R Alternate Dial (1st & 3rd)
9 R Call 1st Number, Back up to 3rd
7
R For Future Use
9 R
8
R Delinquency Follows Zone Activity (Hours)
9 R Delinquency Follows Arming (Days)
44
R Communications Disabled
5.2 Programming Worksheets
[381] Second Communicator Options
Opt
Def
ON
OFF
1
R Open After Alarm Keypad Ringback Enabled
9 R Open After Alarm Keypad Ringback Disabled
2
R Open After Alarm Bell Ringback Enabled
9 R Open After Alarm Bell Ringback Disabled
3
R SIA Sends Programmed Reporting Codes
9 R SIA Sends Automatic Reporting Codes
4
R Closing Confirmation Enabled
9 R Closing Confirmation Disabled
5
9 R Talk/Listen on Phone Lines 1/3
R No Talk/Listen on Phone Lines 1/3
6
9 R Talk/Listen on Phone Line 2
R No Talk/Listen on Phone Line 2
7
R Contact ID Uses Programmed Reporting Codes
9 R Contact ID Uses Automatic Reporting Codes
8
R
9 R Communications Priority Disabled
Communications Priority Enabled
[382] Third Communicator Options
Opt
Def
ON
OFF
1
R
Contact ID Partial Closing Identifier is “5”
9 R
Contact ID Partial Closing Identifier is “4”
2
R
R
R
R
R
R
R
Alarm Communications Enabled During Walk Test*
9 R
Alarm Communications Disabled During Walk Test
Communication Cancelled Message Enabled (ON for SIA CP-01)
9 R
Communication Cancelled Message Disabled
Call Waiting Cancel Enabled**
9 R
Call Waiting Cancel Disabled
T-Link Interface Enabled
9 R
T-Link Interface Disabled
AC Failure Transmission Delay is in Hours
9 R
AC Failure Transmission Delay is in Minutes
Number of Dialing Attempt for Residential Dial is 1
9 R
Residential Dial Follows Dialing Attempts Counter
For Future Use
9 R
3
4
5
6
7
8
*This option must remain OFF for SIA CP-01 installations.
** A Call Waiting Cancel on a non-Call Waiting line will prevent successful connection to the central station.
[383] Fourth Communicator Options
Opt
1
2
Def
R
R
ON
OFF
Account Code Follows Phone Number
9 R
For Future Use
9 R
Acount Code Follows Partition
[389] T-Link Fault Check Timer
Default: 003I_______I_______I_______IValid entries are 001-255 minutes
DLS Downloading
[401] Downloading Option Codes
Opt
1
2
3
4
5
6
7
8
Def
ON
OFF
R
R
R
Answering Machine/Double Call enabled
9 R
Answering Machine/Double Call disable
User Can Enable DLS Window
9 R
User Cannot Enable DLS Window
Call Back Enabled
9 R
Call Back Disabled
R
R
R
R
R
User Initiated Call Up Enabled
9 R
User Initiated Call Up Disabled
Auto Event Buffer Upload Enabled
9 R
Auto Event Buffer Upload Disabled
300 Baud Call Up
9 R 110 Baud Call Up
For Future Use
9 R
For Future Use
9 R
45
PowerSeries - PC1616/PC1832/PC1864
[402] DLS Downloading Telephone Number (32 Digits)
|____D___|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|
[403]-[404] DLS Downloading Access Code / Panel ID Code (Enter 6 Hexadecimal Digits)
Panel
Default
[403] Downloading Access Code
[404] Panel ID Code
PC1616
161600
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
PC1832
183200
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
PC1864
186400
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
[405] Answering Machine Double Call Timer
[406] Number of Rings to Answer On
Default 060 I_______I_______I_______I (000-255 seconds)
Default 000 I_______I_______I_______I (000-010 rings)
[499] Initiate PC-Link Downloading
Enter [499][Installer Code][499]
[501]- [554]Programmable Output Attributes
Program only the following attributes for the PGM options listed. All others will be ignored. PGM options are programmed in [009], [010] & [011].
PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF; Blank = Attribute not available):
Attribute:
1
2
3
4
ON Not used Not used True Output Follows Timer
OFF
—
—
Inverted
On / Off
5
Code Req.
No Code Req.
PGM Option
[01] Residential Burglary / Fire Bell Output
Y
[02] For Future Use
[03] Sensor Reset [4][7][2]
Y
[04] 2-Wire Smoke Support (PGM2 only)
Y
[05] System Armed Status
Y
[06] Ready To Arm
Y
[07] Kypad Buzzer Follower Mode
Y
[08] Courtesy Pulse
Y
[11] System Tamper (all sources, zones, keypad, modules)
Y
[12] TLM and Alarm
Y
[13] Kiss-off Output
Y
Y
[14] Ground Start Pulse
Y
Y
[15] Remote Operation (DLS Support)
Y
Y
[16] For Future Use
Y
[17] Away Armed Status
Y
[18] Stay Armed Status
Y
[19] Command Output #1, [4][7][1]
Y
Y
Y
[20] Command Output #2, [4][7][2]
Y
Y
N
[21] Command Output #3, [4][7][3]
Y
Y
N
[22] Command Output #4, [4][7][4]
Y
Y
N
[23] 24 Hr Silent Input (PGM2 only)
Y
[24] 24 Hr Audible Input (PGM2 only)
Y
[25] Delayed Burglary & Fire Output
Y
[26] Battery Test Output
Y
[28] Holdup Output
Y
[30] Partition Status Alarm Memory Output
Y
[33]Bell Status and Programming Acess Output
Y
[34]Away Armed with no Zone Bypassed Status
Y
46
6
7
8
Not used Not used Not used
—
—
—
5.2 Programming Worksheets
1
Attribute:
PGM Option
2
3
4
5
6
7
8
ON
Serv. req.
AC Fail
TLM Fault
FTC
Zone Fault
Zone Tmp.
Zn. Low Bat.
Loss of Clock
OFF
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Y
Y
Y
Y
Y
Y
Y
Y
ON
Burg. Evnt.
Fire
Evnt.
Panic Evnt.
Med. Evnt.
Supv. Evnt.
Priority Evnt.
Holdup Evnt.
Follows Timer*
OFF
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Latched
Y
Y
Y
Y
Y
Y
Y
N
Fire Alarm
Panic
Alarm
Burglary
Alarm
Open/Close
Zone Aut.o
Bypass
Medical
Alarm
Police Code
Active When
true
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Latched
N
N
N
N
N
N
N
N
Future Use
Future
Use
Future Use
Future Use
Future Use
Future Use
Future Use
Follows Timer
[09] System Trouble
[10] System Event
ON
Disabled
OFF
[31] Alternate Communicator
ON
OFF
Latched
N
N
N
N
N
N
N
N
Future Use
Future
Use
True Output
Future Use
Future Use
Future Use
Future Use
AND Logic
[32] Open After Alarm
ON
OFF
Inverted
N
[29], [35]-[41] Zone Follower
Section PGM
#
Main Board
[501]
1
1
2
(
)
I________I
I________|
[502]
)
I________I
Main Board / PC5208
[503] ** 3
(
)
(
I________I
2
Output
Type*
N
OR Logic
N
3
N
N
4
5
I________|
I________|
I________|
I________|
I________|
I________|
I________|
I________|
I________|
N
6
N
N
7
8
I________|
I________|
I________I
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________I
[504] ** 4
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
*Record here based on programming in [009], [010] and [011].
** These two sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on the
PC5208. If you use both the main panel and the PC5208 outputs, PGM3 will work the same as the first PC5208 output, and PGM4
will work the same as the second PC5208 output.
Section PGM
#
PC5208
[505]
5
Output
Type*
1
2
3
(
[506]
6
(
[507]
7
[508]
8
4
)
I________I
I________|
I________|
I________|
)
I________I
I________|
I________|
I________|
(
)
I________I
I________|
I________|
(
)
I________I
I________|
I________|
5
6
7
8
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________|
I________I
[509]
9
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[510]
10
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[511]
11
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[512]
12
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[513]
13
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[514]
14
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
PC5204
*Record here based on programming in [009], [010] and [011].
47
PowerSeries - PC1616/PC1832/PC1864
PGM Output Partition Assignment
Section PGM
#
Main Board
[551]
1
[552]
Partition: 1
2
2
3
4
5
6
7
8
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
Main Board / PC5208
[553]
3
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[554]
4
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
PC5208
[555]
[556]
5
6
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[557]
7
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[558]
[559]
8
9
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[560]
PC5204
10
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[561]
11
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[562]
12
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[563]
13
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[564]
14
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
Zone Follower PGM Zone Assignment
If a Zone Follower PGM type 29, 35-41 is used, the PGM Output Partition Assignment will be treated as a PGM Output Zone Assignment. Each Zone Follower PGM applies to a different bank of zones as in the below table. Record the assignments above.
Option:
[29] Zone Follower
1
2
3
4
5
6
7
8
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
[35] Zone Follower
Zone 9
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
[36] Zone Follower
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
[37] Zone Follower
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
[38] Zone Follower
Zone 33
Zone 34
Zone 35
Zone 36
Zone 37
Zone 38
Zone 39
Zone 40
[39] Zone Follower
Zone 41
Zone 42
Zone 43
Zone 44
Zone 45
Zone 46
Zone 47
Zone 48
[40] Zone Follower
Zone 49
Zone 50
Zone 51
Zone 52
Zone 53
Zone 54
Zone 55
Zone 56
[41] Zone Follower
Zone 57
Zone 58
Zone 59
Zone 60
Zone 61
Zone 62
Zone 63
Zone 64
Extended Reporting Codes
[601]-[604] Closing (Arming) Reporting Codes, Access Codes 33-95
Section
[601]
Code 33
Code 34
Code 35
Code 36
Code 37
I_______I_______I
[602]
[603]
[604]
48
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 38
Code 39
Code 40
I_______I_______I
I_______I_______I
I_______I_______I
Code 41
Code 42
Code 43
Code 44
Code 45
Code 46
Code 47
Code 48
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 49
Code 50
Code 51
Code 52
Code 53
Code 54
Code 55
Code 56
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 57
Code 58
Code 59
Code 60
Code 61
Code 62
Code 63
Code 64
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 65
Code 66
Code 67
Code 68
Code 69
Code 70
Code 71
Code 72
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 73
Code 74
Code 75
Code 76
Code 77
Code 78
Code 79
Code 80
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 81
Code 82
Code 83
Code 84
Code 85
Code 86
Code 87
Code 88
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 94
Code 89
Code 90
Code 91
Code 92
Code 93
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 95
I_______I_______I
5.2 Programming Worksheets
[605]-[608] Opening (Disarming) Reporting Codes, Access Codes 33-95
Section
[605]
Code 33
Code 34
Code 35
Code 36
Code 37
I_______I_______I
[606]
[607]
[608]
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 38
Code 39
Code 40
I_______I_______I
I_______I_______I
I_______I_______I
Code 41
Code 42
Code 43
Code 44
Code 45
Code 46
Code 47
Code 48
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 49
Code 50
Code 51
Code 52
Code 53
Code 54
Code 55
Code 56
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 57
Code 58
Code 59
Code 60
Code 61
Code 62
Code 63
Code 64
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 65
Code 66
Code 67
Code 68
Code 69
Code 70
Code 71
Code 72
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 73
Code 74
Code 75
Code 76
Code 77
Code 78
Code 79
Code 80
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 81
Code 82
Code 83
Code 84
Code 85
Code 86
Code 87
Code 88
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 94
Code 89
Code 90
Code 91
Code 92
Code 93
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 95
I_______I_______I
Automatic Disarming Schedule
Enter a four-digit number (HH:MM) for each day that the system will auto-disarm for each partition (Section [681] for Partition 1
through section [688] for Partition 8). Valid entries are 0000-2359. All entries are disabled (9999) by default.
Sunday
[681]
[682]
[683]
[684]
[685]
[686]
[687]
[688]
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
Auto-Disarm Holiday Schedule
Enter a six-digit number (MM:DD:YY) for each day that the system will skip auto-disarm for each partition (Section [181] for Partition
1 through section [188] for Partition 8). Program [99][99][99] to disable Auto-Disarm schedule. All entries are disabled by default.
[691]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
[692]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
[693]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
[694]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
49
PowerSeries - PC1616/PC1832/PC1864
[695]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
[696]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
[697]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
[698]
Holiday 1
Holiday 2
Holiday 3
Holiday 4
Holiday 5
Holiday 6
Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
Holiday 8
Holiday 9
Holiday 10
Holiday 11
Holiday 12
Holiday 13
Holiday 14
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I
INTERNATIONAL PROGRAMMING
[700] Automatic Clock Adjust
Default = 60 |________|_________| Valid Entries 01-99 Seconds
[701] First International Options
Opt
1
2
3
4
5
6
7
8
Def
R
R
R
R
R
R
R
R
ON
OFF
50 Hz AC
Time Base - Internal Crystal
AC/DC Arming Inhibit Enabled
All System Tampers Require Installer Reset
6-digit User Access Codes
Busy Tone Detection Enabled
High Current Battery Charge
DLS/Audio has no priority
9
9
9
9
9
9
9
9
R
R
R
R
R
R
R
R
60 Hz AC
Time Base - AC Line
AC/DC Arming Inhibit Disabled
All System Tampers Follow Restore
4-digit User Access Codes
Busy Tone Detection Disabled
Standard Current Battery Discharge
DLS/Audio has priority
[702] Second International Options
Opt
1
2
3
4
5
6
7
8
Def ON
R
9 R
R
R
R
R
R
R
OFF
Pulse Dialing Make/Break Ratio is 33/67
9 R
Force Dialing Enabled
Land Line Test Transmission in Minutes
1600 Hz Handshake
ID Tone Enabled
2100 Hz ID Tone
One Time 1-Hr User Enabled DLS Window
Bell on FTC when Armed
9
9
9
9
9
9
[703] Delay Between Dialing Attempts
Default = 003 |________|_________|_________|
50
Valid Entries 001-255 Seconds
R
R
R
R
R
R
R
Pulse Dialing Make/Break Ratio is 40/60
Force Dialing Disabled
Land Line Test Transmission in Days
Standard Handshake
ID Tone Disabled
1300 Hz ID Tone
Full 6-Hr User Enabled DLS Window
FTC Trouble only when Armed
Module Programming
Module Programming
[801] PC5400 Printer Module Programming
Refer to the PC5400 Installation Manual for installation and programming instructions.
[802] PC59xx VOX Module Programming
Refer to the PC59xx Installation Manual for installation and programming instructions.
[804] PC5132 Wireless Expansion Programming
Refer to the PC5132 Installation Manual for programming locations and instructions.
[805] PC5100 Programming
Refer to the PC5100 Installation Manual for programming locations and instructions.
[851] T-Link Programming
Refer to the T-Link Installation Manual for programming locations and instructions.
Special Installer Functions
[899] Template Programming
[900] Panel Version Displayed
[901] InstallerWalk Test Mode Enable/Disable
[902] Module Supervision Reset
[903] Module Supervision Field
[904] Wireless Module Placement Test
[905] - [909] For Future Use
[990] Installer Lockout Enable
[991] Installer Lockout Disable
[992] For Future Use
[993] Restore Alternate Communicator to Default Programming
[994] For Future Use
[995] Restore Escort5580 to Default Programming
[996] Restore PC5132 to Default Programming
[997] Restore PC5400 to Default Programming
[998] Restore PC59xx to Default Programming
[999] Restore Control Panel to Default Programming
51
PowerSeries - PC1616/PC1832/PC1864
For the Record
Customer: ___________________________________________________________________________________________________________
Address: ____________________________________________________________________________________________________________
Telephone: ______________________________________________Installation Date:_____________________________________________
Installers Code: ______________________________________________________________________________________________________
Module Name
Description
Location
PC1616/PC1832/PC1864
Main Panel
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
I________________________________I
I____________________I
I_____________________________________________________________________________________________I
Keypads
Keypad Type
Location
Keypad 1
I____________________I
I_____________________________________________________________________________________________I
Keypad 2
I____________________I
I_____________________________________________________________________________________________I
Keypad 3
I____________________I
I_____________________________________________________________________________________________I
Keypad 4
I____________________I
I_____________________________________________________________________________________________I
Keypad 5
I____________________I
I_____________________________________________________________________________________________I
Keypad 6
I____________________I
I_____________________________________________________________________________________________I
Keypad 7
I____________________I
I_____________________________________________________________________________________________I
Keypad 8
I____________________I
I_____________________________________________________________________________________________I
52
Module Programming
Zone Programming Summary
Zone programming can be found in sections [001] - [004], [101] - [164], [020], [202]-[265]. Use this area to record a summary of your
zone programming.
System
Zone
Zone
Label
Zone
Type
System
Zone
Zone
Label
Zone
Type
Zone 1
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 33
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 2
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 34
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 3
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 35
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 4
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 36
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 5
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 37
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 6
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 38
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 7
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 39
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 8
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 40
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 9
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 41
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 10
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 42
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 11
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 43
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 12
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 44
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 13
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 45
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 14
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 46
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 15
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 47
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 16
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 48
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 17
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 49
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 18
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 50
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 19
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 51
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 20
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 52
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 21
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 53
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 22
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 54
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 23
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 55
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 24
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 56
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 25
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 57
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 26
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 58
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 27
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 59
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 28
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 60
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 29
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 61
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 30
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 62
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 31
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 63
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 32
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
Zone 64
I___I___I___I___I___I___I___I___I___I___I___I___I___I___I
I___I___I
53
PowerSeries - PC1616/PC1832/PC1864
Appendix A: Reporting Codes
The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on reporting code formats and notes
about individual reporting codes, (see Section 5.6 Communicator Programming PWS Sect 6).
Contact ID
The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to indicate specific information
about the signal. For example, if zone 1 is an entry/exit point, you could program the event code as [34]. The central station would receive the
following:
*BURG - ENTRY/EXIT - 1 where the “1” indicates which zone went into alarm.
SIA Format - Level 2 (Hardcoded)
The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - October
1997. This format will send the Account Code along with its data transmission. The transmission will look similar to the following at the receiver:
N Ri01
BA 01
N = New Event
Ri01 = Partition /Area Identifier
BA = Burglary Alarm
01 = Zone 1
NOTE: A system event will use the Area Identifier Ri00.
Section #
Dialer
Direction*
Automatic
Contact ID
Codes
SIA Auto
Rep Codes**
Reporting Code
Code Sent When...
[320]-[323]
Zone Alarms
Zone goes into alarm
A/R
[324]-[327]
Zone Restorals
Alarm condition has been restored
A/R
[328]
Duress Alarm
Duress code entered at keypad
A/R
(1) 21
HA-00
[328]
Opening After Alarm
System disarmed with alarm in memory
A/R
(4) 58
OR-UU
[328]
Recent Closing
Alarm occurs within two minutes of system arming
A/R
(4) 59
CR-00
[328]
Zone Expander Supervisory Panel loses/restores supervisory transmission over the Keybus
Alarm/Rest.
from zone expansion modules, or keypads with zone inputs
A/R
(1) 43
UA-00/UH-00
[328]
Cross Zone (Police Code)
Alarm
A/R
(1) 39
BM-00/BV-00
[328]
Burglary Not Verified
A/R
(3) 78
BG-00
[328]
Alarm Cancelled
A/R
(4) A6
BC-00
[329]
[F] Key Alarm/Rest.
Keypad fire alarm (alarm and restore rep. codes sent together)
A/R
(1) 1A
FA-00/FH-00
[329]
[A] Key Alarm/Rest.
Keypad auxiliary alarm (alarm and restore rep. codes sent
together)
A/R
(1) AA
MA-00/MH-00
[329]
[P] Key Alarm/Rest.
Keypad panic alarm (alarm and restore rep. codes sent together) A/R
(1) 2A
PA-00/PH-00
[329]
Aux Input Alarm/Rest
Option#23/24: a panic button wired to PGM 2 is pressed/access A/R
code is entered
Option #04: a 2-wire smoke detector wired to PGM 2 goes into A/R
alarm/alarm is cleared.
(1) 4A
UA-99/UH-99
(1) 11
FA-99/FH-99
Two zones on the same partition go into alarm during any given
armed-to-armed period (incl. 24Hr zones)
See Table 3
See Table 3
[330]-[337]
Zone Tamper/Restoral
Zone is tampered / tamper condition restored
T/R
(3) 83
TA-ZZ/TR-ZZ
[338]
General System Tamper/
Rest.
Enrolled module with tamper inputs has a tamper alarm/all mod- T/R
ule tampers restored
(1) 45
ES-00/EJ-00
[338]
Keypad Lockout
Maximum number of incorrect access codes has been entered at T/R
a keypad
(4) 61
JA-00
[339-341]
Closings
System armed (user 01-32 indicated)
O/C
(4) A1
CL-UU
[341]
Partial Closing
One or more zones bypassed when system armed
O/C
(4) 56
CG-ZZ
[341]
Special Closing
Closing (arming) using one of the following methods: quick arm,
auto arm, keyswitch, function key, maintenance code, DLS software, wireless key
O/C
(4) AA
CL-00
[341]
Late to Close
Whenever the Auto-arm prealert sounds (if the Late to Close
option is enabled)
O/C
(4) 54
CI-00
[341]
Exit Fault
O/C
(3) 74
EE-00
[342-344]
Openings
System disarmed (user 01-32 indicated)
O/C
(4) A1
OP-UU
[344]
Auto-arm Cancellation
Auto-arm cancelled
O/C
(4) 55
CI-00
[344]
Special Opening
Opening (disarming) using one of the following methods: keyswitch, maintenance code, DLS software, wireless key
O/C
(4) AA
OP-00
[345]-[346]
Battery Trouble/Rest.
PC1616/PC1832/PC1864 battery is low/battery restored
MA/R
(3) A2
YT-00/YR-00
[345]-[346]
AC Line Trouble/Rest.
AC power to control panel is disconnected or interrupted/AC
power restored (Both codes follow AC Failure Comm. Delay.)
MA/R
(3) A1
AT-00/AR-00
[345]-[346]
Bell Circuit Trouble/Rest.
Open or short circuit detected across bell terminals/bell circuit
restored
MA/R
(3) 21
YA-99/YH-99
[345]-[346]
Fire Trouble/Rest.
Trouble occurs/restores on a fire zone
MA/R
(3) 73
FT-99/FJ-99
Appendix A: Reporting Codes
Dialer
Direction*
Automatic
Contact ID
Codes
SIA Auto
Rep Codes**
Section #
Reporting Code
Code Sent When...
[345]-[346]
Auxiliary Power Trouble/
Rest.
Aux voltage supply trouble/restoral
MA/R
(3) 12
YP-00/YQ-00
[345]
TLM Failure
Telephone line monitoring trouble
MA/R
(3) 51
LT-01
[346]
TLM Restore
Telephone line restored
MA/R
(3) 51
LR-01
[345]-[346]
Gen System Trouble/Rest.
“Service Required” trouble occurs (view troubles using [*][2])/trou- MA/R
ble restored
(3) AA
YX-00/YZ-00
[345]-[346]
Gen System Supervisory
Trouble/Rest.
Control panel loses/restores communications with module(s)
connected to the Keybus
MA/R
(3) 3A
ET-00/ER-00
[347]
Phone# 1 or 2 FTC Restoral Control panel has restored communications to central station on MA/R
Phone# 1 or 2 (after FTC)
(3) 54
YK-00
[347]
Event Buffer is 75% Full
Event buffer is almost full since last upload
MA/R
(6) 22
JL-00
[347]
DLS Lead In
Downloading session start
MA/R
(4) 11
RB-00
[347]
DLS Lead Out
Downloading session complete
MA/R
(4) 12
RS-00
[347]
Zone Fault/Rest.
One or more zones have faults/restored
MA/R
(3) 80
UT-ZZ/UJ-ZZ
[347]
Delinquency
Programmed amount of time (days or hours) for delinquency has MA/R
expired without zone activity, or without system being armed
(6) 54***
CD-00
[347]
Wireless Device Low Battery Wireless zones, panic pendants, handheld keypads, wireless
Trouble/Rest.
keys have low battery/all low batteries restored
MA/R
(3) 84
XT-00/XR-00
XT-ZZ/XR-ZZ****
LB-00
[347]
Installer Lead In
Installer’s mode has been entered
MA/R
(6)27
[347]
Installer Lead Out
Installer’s mode has been exited
MA/R
(6)28
LS-00
[348]
Walk Test End
End of test
T
(6) A7
TE-00
[348]
Walk Test Begin
Beginning of test
T
(6) A7
TS-00
[348]
Periodic Test with Trouble
Periodic system test transmission with trouble
T
(6) A8
RY-00
[348]
Periodic Test
Periodic system test transmission
T
(6) A2
RP-00
[348]
System Test
[*][6] bell/communications test
T
(6) A1
RX-00
[349]
PC5700 Ground Fault Trouble/Restore
Ground/Fault/Trouble occurs on the PC5700
MA/R
(3) 1A
US-00/UR-00
[349]
PC5700 TLM Line 1 Trouble/ TLM Trouble /Restore occurs on the PC5700
Restore
MA/R
(3) 51
LT-01/LR-01
[349]
PC5700 TLM Line 2 Trouble/ TLM Trouble /Restore occurs on the PC5700
Restore
MA/R
(3) 52
LT-02/LR-02
[601]-[604]
Closings
System armed (user 33-95 indicated)
O/C
(4) A1
CL-UU
[605]-[608]
Openings
System disarmed (user 33-95 indicated)
O/C
(4) A1
OP-UU
*
**
***
****
A/R = alarms/restorals; T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions
UU = user number (user01-42); ZZ = zone number (01-64)
Use the “Fail to close” event code [(4)54] to report closing or activity delinquency. Ensure the central station is aware that this code is used.
Zones are identified, panic pendants, wireless keys, and handheld keypads are not.
Contact ID Zone Alarm/Restoral Event Codes
(as per SIA DCS: ‘Contact ID’ 01-1999):
Program any of these codes for zone alarms/restorals when
using the standard (non-automatic) Contact ID reporting format.
Medical Alarms
(1)AA Medical
(1)A1 Pendant Transmitter
(1)A2 Fail to Report In
Fire Alarms
(1)1A Fire Alarm
(1)11 Smoke
(1)12 Combustion
(1)13 Water Flow
(1)14 Heat
(1)15 Pull Station
(1)16 Duct
(1)17 Flame
(1)18 Near Alarm
Panic Alarms
(1)2A Panic
(1)21 Duress
(1)22 Silent
(1)23 Audible
Burglar Alarms
(1)3A Burglary
(1)31 Perimeter
(1)32 Interior
(1)33 24 Hour
(1)34 Entry / Exit
(1)35 Day / Night
(1)36 Outdoor
(1)37 Tamper
(1)38 Near Alarm
General Alarms
(1)4A General Alarm
(1)43 Exp. module failure
(1)44 Sensor tamper
(1)45 Module Tamper
(1)4A Cross Zone Police Code
24 Hour Non-Burglary
(1)5A 24 Hour non-Burg
(1)51 Gas detected
(1)52 Refrigeration
(1)53 Loss of Heat
(1)54 Water Leakage
(1)55 Foil Break
(1)56 Day Trouble
(1)57 Low bottled Gas level
(1)58 High Temp
(1)59 Low Temp
(1)61 Loss of Air Flow
SIA Format Automatic Zone Alarm/Restoral Codes
Zone Definition
SIA Auto Rep
Codes*
Contact ID Auto
Rep Codes*
Delay 1
Delay 2
Instant
Interior
Interior Stay/Away
Delay Stay/Away
Delayed 24-Hr Fire
Standard 24-Hr Fire
24-Hr Supervisory
24-Hr Supervisory Buzzer
24-Hr Burg
24-Hr Holdup
24-Hr Gas
24-Hr Heat
24-Hr Medical
24-Hr Panic
24-Hr Emergency (non-medical)
24-Hr Sprinkler
24-Hr Water
24-Hr Freeze
24-Hr Latching
Interior Delay
Auto Verified Fire
24-Hr Fire Supervisory
Day Zone
Instant Stay/Away
24-Hr Bell/Buzzer
24-Hr Non-latching Tamper
Night Zone
Delayed 24-Hr Fire (Wireless)
Standard 24-Hr Fire (Wireless)
BA-ZZ/BH-ZZ
BA-ZZ/BH-ZZ
BA-ZZ/BH-ZZ
BA-ZZ/BH-ZZ
BA-ZZ/BH-ZZ
BA-ZZ/BH-ZZ
FA-ZZ/FH-ZZ
FA-ZZ/FH-ZZ
US-ZZ/UR-ZZ
UA-ZZ/UH-ZZ
BA-ZZ/BH-ZZ
HA-ZZ/HH-ZZ
GA-ZZ/GH-ZZ
KA-ZZ/KH-ZZ
MA-ZZ/MH-ZZ
PA-ZZ/PH-ZZ
QA-ZZ/QH-ZZ
SA-ZZ/SH-ZZ
WA-ZZ/WH-ZZ
ZA-ZZ/ZH-ZZ
UA-ZZ/UH-ZZ
BA-ZZ/BH-ZZ
FA-ZZ/FH-ZZ
FS-ZZ/FV-ZZ
BA-ZZ/BH-ZZ
BA-ZZ/BH-ZZ
UA-ZZ/UH-ZZ
UA-ZZ/UH-ZZ
BA-ZZ/BH-ZZ
FA-ZZ/FH-ZZ
FA-ZZ/FH-ZZ
(1) 3A
(1) 3A
(1) 3A
(1) 3A
(1) 3A
(1) 3A
(1) 1A
(1) 1A
(1) 5A
(1) 5A
(1) 3A
(1) 22
(1) 51
(1) 58
(1) AA
(1) 2A
(1) A1
(1) 13
(1) 54
(1) 59
(1) 4A
(1) 3A
(1) 1A
(2) AA
(1) 3A
(1) 3A
(1) 5A
(1) 4A
(1) 3A
(1) 1A
(1) 1A
* ZZ = zones 01-64
PowerSeries - PC1616/PC1832/PC1864
Appendix B: UL Listed Commercial and Residential Installations
The installation requirements listed below must be met for the following
grades of service.
Central Station and Police Connect (Standard or Encrypted Line Security
Service)
The installation must use T-Link module which communicates over LAN/WAN to
the Sur-Gard MLR-IP receiver or the TL200/250 which communicates over LAN/
WAN/Internet to the SG System III receiver. Polling time must be 90 seconds.
Compromise detection time must be 6 minutes.
Local
•The installation must have a bell which is UL Listed for mercantile local alarms
(AMSECO MBL10B with model AB-12 bell housing).
•The digital communicator must be enabled.
•The control panel must be in the attack-resistant enclosure (DSC Model CMC1 or PC4050CAR).
Central Station and Police Connect (No line security)
•The installation must have a bell which is UL Listed for mercantile local alarms
(AMSECO MBL10B with model AB-12 bell housing).
•The digital communicator must be enabled.
•The control panel must be in the attack resistant enclosure (DSC Model CMC1 or PC4050CAR).
All Commercial Installations
•The Entry Delay must not exceed 120 seconds
•The Exit Delay must not exceed 120 seconds.
•The minimum Bell Time-out is 15 minutes.
Residential Fire & Burglary Installations
•The Entry Delay must not exceed 45 seconds
•The Exit Delay must not exceed 60 seconds.
•The minimum Bell Time-out is 4 minutes.
Home Health Care Signaling Equipment
•There must be at least two keypads, one of either the LCD5500Z/LCD5520Z
or LCD5501Z and one of the following models, PC5508Z, PC5516Z or
PC5532Z.
•Each system shall be programmed to activate an audible Trouble signal within
90 seconds upon loss of microprocessor memory.
•The minimum Bell Time-out is 5 minutes.
Programming
The notes in the programming sections describing the system configurations
for UL Listed installations must be implemented.
Control of the Protected Premises
In order to have a UL Certificated system the protected area is to be under the
responsibility of one ownership and management (i.e., one business under one
name). This may be a group of buildings attached or unattached with different
addresses but under the responsibility of someone having mutual interest. The
person of mutual interest is not the alarm-installing company.
Bell Location
The alarm sounding device (bell) must be located where it can be heard by the
person or persons responsible for maintaining the security system during the
daily arming cycle.
Protection of the Control Unit
The local control and the local power supply must be protected in one of the
following ways:
•The control unit and audible alarm device must be in a protected area which is
armed 24 hours a day.
•Each partition must arm the area protecting the control unit and the audible
alarm device power supply. This may require duplicate protection armed by
each partition. Access to this protected area, without causing an alarm, will
require that all partitions be disarmed.
•In all cases described above, the protected area for the control unit must be
programmed as not-bypassable.
Casual Users
The installer should caution the user(s) not to give system information to casual
users (e.g. codes, bypass methods, etc. to baby-sitters or service people). Only
the One-Time Use codes should be given to casual users.
User Information
The installer should advise the users and note in the User’s Manual:
•Service organization name and telephone number
•The programmed exit time
•The programmed entry time
•Test system weekly
Two-Wire Smoke Detector Compatibility (if available)
Maximum loop resistance: 24 Ohms
•Operating Voltage Range: 9.8 - 13.8 VDC
•Maximum Alarm Current: 89 mA
•Compatibility Identifier: PC18-1
See Section 1.6 PGM Wiring for compatible 2-wire smoke detectors.
SIA FAR Installations
Minimum requirement system for SIA-FAR Installations:
• 1 PC1616/PC1832/PC1864 Control panel
• 2 Local annunciation devices
The local annunciation devices may be any combination of the following keypads:
• LCD5500Z
• LCD5501Z
• PK5500
• PK5508
• PKP-LCD
• PKP-ICN
• PK5501
• PK5516
The following optional subassembly modules also bear the SIA FAR classification and may be used if desired:
PC5108 Zone Expander Module
Compatible initiating devices: Bravo200 series, 300 series, 400 series, 500
series, 600 series, AC-100, Encore300 series, Force200 series, 210 series,
MN240.
PC5208 Low Current PGM Output Module
The following optional accessory modules also bear the SIA FAR classification
and may be used if desired.
PC5204 Auxiliary Power Supply with PGM output ports
Escort5580/Escort5580TC, PC5400 Printer Module
Caution
• For SIA FAR installations, only use modules / devices that are listed on this
page.
• Fire Alarm Verification feature (Auto Verified Fire zone) is not supported on
2-wire smoke detectors zones. This feature may be enabled for 4-wire smoke
detectors only.
• Call Waiting Cancel (Section 382 Option 4) feature on a non-Call Waiting
line will prevent successful communication to the central station.
• All smoke detectors on the system must be tested annually by conducting
the Installer Walk Test prior to exiting the walk test mode, a sensor reset
must be conducted on the system, [ ][7][2] to reset all latching 4-wire
smoke detectors. Please refer to the smoke detector installation instructions
on how to correctly test the detectors.
Notes
• Programming at installation may be subordinate to other UL requirements
for the intended application.
• Cross zones have the ability to individually protect the intended area (e.g.,
motion detectors, which overlap).
• Cross zoning is not recommended for line security Installations nor is it to be
implemented on exit / entry zones.
• There is a communication delay of 30 seconds in this control panel. It can be
removed, or it can be increased up to 45 seconds at the option of the end
user by consulting with the Installer.
• Do not duplicate any reporting codes. This applies for all communication formats other than SIA sending automatic programmed reporting codes.
• The control unit must be installed with a local sounding device and an offpremise transmission for SIA communication format.
• For ULC Listed Fire Monitoring Installations & module requirements, Refer to
the ULC Installation Information sheet, part# 29002157.
• Use a CSA/cUL transformer, hardwired.
• All tamper circuits may be connected to the same zone.
• Use ULC-LA for AC Power indication.
Appendix C: SIA False Alarm Reduction
Appendix C: SIA False Alarm Reduction
SIA Feature
Programming Section
Comments
Range/Default
Requirement
Exit Time
[005], 3rd entry
Access to Entry and Exit delays for each partition and Bell Time Out for the system
For Full or auto arming:
Range:45- 255 seconds
Default: 60 sec.
Required
(programmable)
Progress Annunciation/
Disable - for Silent Exit
[014], Option 6 ON
Enables audible exit beeps from the keypad for the duration of exit delay
Individual keypads
may be disabled
Default: All Enabled
Allowed
Exit Time Restart
[018], Option 7 ON
Enables the exit delay restart feature
Default: Enabled
Required
Auto Stay Arm on
Unvacated Premises
[001]-[004] Zone type 05, 06
Function Key: Stay Arming. All Stay/Away type zones (05, 06) will be automatically
bypassed
If no exit after full arm
Default: Enabled
Required
Exit Time and Progress
Annunciation/Disable
or Remote Arming
[005] and [014] bit 6
System Times and Audible Exit beeps can be disabled when using the Key fob to arm
away the system
Default: Enabled
Allowed
Entry delay(s)
[005], 1st and 2nd entry
Access to Entry and Exit delays for each partition and Bell Time Out for the system
Note: Combined Entry delay and Communications Delay (Abort Window) shall not
exceed 60s
Range: 30 sec. to 4 min.
Default: 30 sees
Required
(programmable)
Abort Window
for Non-Fire zones
[101]-[164] bit 7 ON
Access to zone attributes, i.e, swinger shutdown, transmission delay and cross zone.
Individual zones attribute bit 7 (Transmission delay) is by default ON
May be disabled
by zone or zone type
Default: Enabled
Required
Abort Window - for
Non-Fire zones
[377], 4th entry
Access to the programmable delay before communicating alarms
Note: Combined Entry delay and Communications Delay (Abort Window) shall not
exceed 60s
Range: 15 - 45 sec.
Default: 30 sees
Required
(programmable)
Abort Annunciation
[382], Option 3 ON
Enables the “Communication Cancelled" message display on all keypads
Annunciate that no
alarm was transmitted
Default: Enabled
Required
Cancel Annunciation
[328], 8th entry
Access to the reporting code for Alarm Cancelled
Annunciate that a
Cancel was transmitted
Default: Enabled
Required
Duress Feature
[*][5] Master Code
[99] Option 2 ON
Do not derive code from an existing Master/User code (e.g., Master code is 1234, the
duress code should not be 1233 or 1235)
No 1+/- derivative of another
user code. No duplicates with
other user codes
Default: disabled
Allowed
Cross Zoning
[018] Option 6
[101]-[164] bit 9 OFF
This option enables Cross Zoning for entire system. Individual zones can be enabled
for Cross zoning via Zone attribute bit 9 in sections [101] - [164]
Programming required
Default: Disabled
Required
Cross Zone Timer
[176]
Access to the programmable Cross Zone timer
May program
Range: 001-255 sec./min.
Default: 60 secs
Allowed
Swinger Shutdown for Alarms
[377] 1st entry
Access to the swinger shutdown limit for zone alarms
For all non-fire zones
shut down at 1 or 2 trips
Default: 1 Trip
Required
(programmable)
Swinger Shutdown Disable
[101] - [164] bit 6 ON
Access to zone attributes, i.e., swinger shutdown, transmission delay and cross zone.
Individual zones attribute bit 6 (Swinger shutdown enabled) is by default ON
For non-police
response zones
Default: Enabled
Allowed
Fire Alarm Verification
Zone type [29]
Auto Verified Fire, use only with 4 wire type detectors that can be reset by the panel 4wire smoke detector powered from AUX + and PGM1 - PGM4 (type 03, Sensor reset)
70 seconds reset and
confirmation time
Default: disabled
Required
Call Waiting Cancel Dial String
[304], [382], Option 4 OFF
Access to the dialing sequence used to disable call waiting
Dependant on user phone
line
Default: disabled
Required
System Test:
[*][6] Master Code, Option 4
The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on.
Refer to the User Manual (part no. 29007165).
Installer Walk Test Mode:
[901]
This mode is used to test each zone on the system for proper functionality.
Alarm Communications
During Walk Test
[382] Option 2:
Enables Communication of zone alarms while installer Walk Test is active.
Walk Test End and Begin
Reporting Codes
[348], 1st and 2nd Entries
Access to the reporting codes for Walk Test Begin and Walk Test End.
Testing
PowerSeries - PC1616/PC1832/PC1864
Appendix D: Troubleshooting Guide
Testing:
•
•
Power up system
Program options as required (See Programming Section)
NOTE: For advanced programming refer to the PC1616/1832/1864 Reference Manual
•
•
Violate, then restore zones
Verify correct Reporting Codes are sent to the Central Station
Troubleshooting:
LCD Programmable-Message Keypad
•
•
•
Press [✱][2] to view a trouble condition.
The trouble light will flash and the LCD will display the first trouble condition present.
Use the arrow keys to scroll through all trouble conditions present.
NOTE: When additional information is available for a specific trouble condition a [✱] will appear on the display.
Press the [✱] key to view the additional information
LED Keypads, LCD Fixed Message Keypads
•
•
•
Press [✱][2] to view a trouble condition.
The trouble light will flash.
Refer to the Trouble Summary chart below to determine the trouble condition(s) present.
Trouble Summary:
Light [1]✱ Service Required - Press [1] for more information
[1] Low Battery
[2] Bell Circuit
[3] General System Trouble
[4] General system Tamper
[5] Module Supervision
[6] RF Jam Detected
[7] PC5204 Low Battery
[8] PC5204 AC Failure
Light [2] AC Trouble
Light [3] Telephone Line Trouble
Light [4] Failure to Communicate
Light [5]✱ Zone Fault -Press [5] for more information
Light [6]✱ Zone Tamper - Press [6] for more information
Light [7]✱ Wireless Device Low Battery - Press [7] for more information
Light [8] Loss of Time or Date
Appendix D: Troubleshooting Guide
Trouble
Cause
Trouble [1] Service Required
[1] Low Battery
Troubleshooting
Press [1] to determine specific trouble
Main panel battery less than 11.1VDC
NOTE: This trouble condition will not
clear until the battery voltage is 12.5VDC
min., under load.
[2] Bell Circuit
Bell+, Bell-...Open Circuit
NOTE: If battery is new allow 1 Hr. for battery to charge.
•
Verify voltage measured across AC terminals is 16-18 VAC.
Replace transformer if required.
•
Disconnect battery wire leads
• Verify battery charging voltage measured across battery leads
= 13.70 - 13.80 VDC.
•
Connect battery, remove AC power
• Verify measured voltage across battery terminals is 12.5VDC
min.
•
•
[3] General System Trouble
PC5204 Output#1 Open Circuit
•
•
Disconnect Bell-/Bell+ wire leads, measure resistance of wire
leads.
• Open circuit indicates break in wiring or defective siren/bell
Jumper Bell+, Bell- with 1K resistor (Brown, Black, Red)
• Verify trouble clears
If Output#1 is unused: Ensure that terminals O1, AUX are
jumpered with 1K resistor (Brown, Black, Red)
If Output #1 is used: Disconnect wire leads from O1, AUX
terminals, measure the resistance of the wire leads
• Open circuit indicates a break in the wiring
PC5204 AUX
•
•
Printer connected to PC5400 offline
Verify printer operation (out of paper, paper jam etc.)
T-Link Network Fault present
T-Link Receiver Trouble present
T-Link Interface Trouble present
Refer to the T-Link TL150/250/350 Installation Manual for details.
[4] General System
Tamper
Tamper input on module(s) open circuit
Short tamper terminal to COM terminal on unused modules connected
to KEYBUS (PC5100, PC5108, PC5200, PC5204, PC5208, PC5320,
PC5400, PC5700).
[5] Module Supervision
Panel does not communicate with module(s) on KEYBUS
Modules are immediately enrolled and supervised when detected on
the KEYBUS. If a module has been removed, or if the slot assignment
of a keypad has been changed, module supervision must be reset.
•
View the event buffer (via DLS or LCD5500 keypad) to identify
the specific module(s) in trouble
•
To reset module supervision:
• Enter Program Section [902].
• Press [#] (wait 1 minute for panel to scan KEYBUS).
•
Enter Program Section [903] to identify modules connected to the
KEYBUS.
Keypad assigned to incorrect slot.
Verify voltage measured across AC input terminals is 16-18VAC.
Disconnect all connections to PC5204 AUX terminal.
• Verify AUX voltage is 13.70 - 13.80 VDC.
[6] RF Jam Detected
Wireless Receiver - excessive noise
detected.
Check for external 433MHZ signal sources
To disable RF Jam: enable Option [7] in program section [804]
subsection [90].
[7] PC5204 Low Battery
PC5204 battery less than 11.5VDC
See [1] Low Battery above
NOTE: This trouble condition will not
clear until the battery voltage is 12.5VDC
min., under load.
[8] PC5204 AC Failure
No AC at PC5204 AC inputs
Verify voltage measured across AC terminals is 16-18VAC.
Replace transformer if required.
PowerSeries - PC1616/PC1832/PC1864
Trouble
Cause
Troubleshooting
No AC at panel AC input
terminals
Verify voltage measured across AC terminals is 16-18VAC. Replace
transformer if required.
Trouble [2] AC Failure
Trouble [3] Telephone Line Trouble
Phone Line Voltage at TIP, RING on main
panel less than 3VDC
•
•
Measure the voltage across TIP and RING on the panel:
• No phone off-hook – 50VDC (approx)
• Any phone off-hook – 5VDC (approx)
Wire incoming line directly to TIP and RING.
• If trouble clears, check wiring or the RJ-31 phone jack.
Trouble [4] Failure to Communicate
Panel fails to communicate one or more
events to central station
Trouble [5] Zone Fault
Connect a headset to TIP and RING of the control panel. Monitor for
the following conditions:
•
Continuous dial tone
• Reverse TIP and RING
•
Recorded operator message comes on
• Verify correct phone number is programmed
• Dial the number programmed using a regular telephone to
determine if a [9] must be dialed or if 800 service is blocked.
•
Panel does not respond to handshakes.
• Verify the format programmed is supported by the central station.
•
Panel transmits data multiple times without receiving a
handshake
• Verify that the account number and reporting codes are correctly programmed.
NOTE:
Contact ID and Pulse formats
• Program a HEX [A] to transmit a digit [0]
SIA format
• Program a digit [0] to transmit a digit [0]
Press [5] to determine specific zones with a fault trouble
Open circuit is present on one or more
fire zones on the main panel or zone
expander
•
•
•
An open circuit is present on PGM2
being used as a 2-wire smoke detector
input
•
•
•
Ensure fire zones have a 5.6K resistor (Green, Blue, Red) connected.
Remove the wire leads from Z and COM terminals and measure
the resistance of the wire leads.
• An open circuit indicates a break in the wiring or resistor not
connected.
Connect a 5.6K resistor (Green, Blue, Red) across the Z and
COM terminals. Verify the trouble condition clears.
Ensure the correct 2.2K end-of-line resistor is connected (Red,
Red, Red).
Remove the wire leads from PGM2 and AUX+ terminals and
measure the resistance of the wire leads.
• An open circuit indicates a break in the wiring or no resistor
connected.
Connect a 2.2K resistor (Red, Red, Red) across the PGM2 and
AUX+ terminals. Verify the trouble condition clears.
Appendix D: Troubleshooting Guide
Trouble
Cause
Troubleshooting
Trouble [5] Zone Fault (Cont.)
One or more wireless devices have not
checked in within the programmed time
•
•
A short circuit is present on one or more
zones with double end-of-line resistors
enabled
•
•
Trouble [6] Zone Tamper
Remove the wire leads from Z and COM terminals and measure
the resistance of the wire leads.
• A short circuit indicates a short in the wiring.
Connect a 5.6K resistor (Green, Blue, Red) across the Z and
COM terminals.
• Verify the trouble condition clears.
Press [6] to determine specific zones with a tamper trouble
A tamper condition is present on one or
more wireless devices
•
•
Perform a Module Placement Test –Section [904]
Violate, then restore the tamper:
• If no test result then replace wireless device
An open circuit is present on one or more
zones with double end-of-line resistors
enabled
•
•
Remove the wire leads from Z and COM terminals.
Measure the resistance of the wire leads.
• Open circuit indicates a break in the wiring.
Connect a 5.6K resistor (Green, Blue, Red) across the Z and
COM terminals.
• Verify the trouble condition clears.
•
Trouble [7] Wireless Device Low Battery
1st press
– Wireless Zones
2nd press
– Handheld Keypads
3rd press
– Wireless Keys
If the trouble occurs immediately, a conflict with a hard wired
zone exists:
• The zone being used is already assigned to a PC5108 zone
expander
• The zone being used is assigned as a keypad zone
Perform a Module Placement Test – Program Section [904] and
verify the wireless device is in a good location.
• If bad test results occur, test the wireless device in another
location
• If the wireless device now tests good, the original mounting
location is bad
• If the wireless device continues to give bad test results
replace the wireless device
Press [7] to toggle through specific devices with low battery trouble
One or more wireless devices has a low
battery
Replace battery
NOTE: The event will not be logged to
the event buffer until the wireless device
low battery delay time expires
• Program Section [377] Opt 9
NOTE: Replacing batteries will cause a tamper. Replacing cover will
restore the tamper causing the associated reporting codes to be sent
to the Central Station.
Trouble [8] Loss of Clock/Date
The main panel internal clock is not set
To program the time and date:
•
Enter [✱][6][Master Code] then Press [1]
•
Enter the time and date (in military) using the following format:
HH:MM MM/DD/YY
Example.
For 6:00 pm, June 29, 2005
Enter: [18] [00] [06] [29] [05]
IMPORTANT!
Ensure you have the following information available before contacting Customer Support
- Control Panel Type and Version, (e.g., PC1864 v4.1)
NOTE: Version number can be accessed by entering [✱][Installer Code][900] on any LCD keypad. This information is also located on a sticker on the Printed Circuit Board.
- List of modules connected to Control Panel, (e.g., PC5400, PC5204 etc.)
PowerSeries - PC1616/PC1832/PC1864
Appendix E: Template Programming
Template programming allows quick programming of the minimum functions required for basic operation. The below tables are used to determine the desired template to be used ( for information on performing template programming see Section 4 – Programming Descriptions). Each
digit represents 1 of the template sections listed below. The option number selected for each digit will make up the 5 digit template programming
code.
• Digit 1 selects Zone 1-8 definition options.
Option
Zn1
Zn2
Zn3
Zn4
Zn5
Zn6
Zn7
Zn8
1 Delay 1
1
1
3
3
3
4
4
4
4
2 Delay 2
2
1
3
3
5
5
5
5
8
3 Instant
3
1
3
3
5
5
5
5
7
4 Interior
4
1
1
3
3
3
3
3
3
5 Interior Stay/Away
5
1
3
3
6
5
5
5
5
6 Delayed Stay/Away
6
1
3
3
6
5
5
5
8
7 Delayed 24-Hour Fire
Refer to Section 4 for Zone definition details
•
Digit 2 selects system EOL configuration options.
Option
•
8 Standard 24-Hour Fire
[013] Opt 1
[013] Opt 2
1
NC loops
ON
OFF
2
SEOL
OFF
OFF
3
DEOL
OFF
ON
Digit 3 selects panel communications options.
Op#
Phone Line 1
Programming Section
Phone Line 2
Programming Section
1
Disabled
[380] Opt 1 OFF
Disabled
[380] Opt 1 OFF
2
SIA automatic Reporting Codes enabled
[350] 1st Phone # [04]
[380] Opt 1 ON
[381] Opt 3 OFF
SIA automatic
Reporting Codes
enabled
[350] 2nd Phone # [XX]
3
Contact ID Reporting Codes enabled
[350] 1st Phone # [03]
[380] Opt 1 ON
[381] Opt 7 OFF
SIA automatic
Reporting Codes
enabled
[350] 2nd Phone # [XX]
4
SIA automatic Reporting Codes enabled
[350] 1st Phone #[04]
[380] Opt 1 ON
[381] Opt 3 OFF
Residential Dial
Enabled
[350] 2nd Phone # [06]
5
Contact ID Reporting Codes enabled
[350] 1st Phone # [03]
[380] Opt 1 ON
Opt 7 OFF
Residential Dial
Enabled
[350] 2nd Phone # [06]
6
Contact ID Reporting Codes enabled
[350] 1st Phone # [03]
[380] Opt 1 ON
[381] Opt 7 OFF
Contact ID
Reporting Codes
Enabled
[350] 2nd Phone # [03]
Appendix E: Template Programming
•
Digit 4 selects reporting code configurations
Option
Common
Group
Selected
Troubles
Openings/
Closings
Zone
Restorals
DLS/Installer
Lead In/Out
1
2
3
4
5
6
7
8
indicates included, Blank indicates default setting,
indicates disabled
Common Group
Description
Phone 1
Phone 2
Sections
Set all Reporting Codes to automatic
[320] - [349], [601] - [608] FF
Alarm/Restore call directions enabled
[351][1] ON, [2] OFF
Tamper/Restore Call directions disabled
[359][1] OFF, [2] OFF
Openimg/Closing Call directions disabled
[367][1] OFF, [2] OFF
Maintenance Call Directions enabled
[375][1] ON, [2] OFF
Test Transmission Call directions disabled
[376][1] OFF, [2] OFF
Selected Troubles
Trouble
[345] Alarms
[346] Restoral
Battery
FF
FF
AC Failure
00
00
Bell Circuit
FF
FF
Fire, Alarm
FF
FF
Aux PS
FF
FF
TLM
00
FF
General System
00
00
General System Supervisory
FF
FF
FF = Communicate in automatic format , 00 = Disabled
PowerSeries - PC1616/PC1832/PC1864
Openings & Closings
Users
CLOSINGS, Residential Dial Reporting codes
Section
1-8
51
52
53
54
55
56
57
58
[339]
9-16
61
62
63
64
65
66
67
68
[339]
17-24
71
72
73
74
75
76
77
78
[340]
25-32
81
82
83
84
85
86
87
88
[340]
33-40
FF
FF
FF
FF
FF
FF
FF
98
[601]
Users
OPENINGS, Residential Dial Reporting codes
1-8
11
12
13
14
15
16
17
18
[342]
9-16
21
22
23
24
25
26
27
28
[342]
17-24
31
32
33
34
35
36
37
38
[343]
25-32
41
42
43
44
45
46
47
48
[343]
33-40
FF
FF
FF
FF
FF
FF
FF
98
[605]
Section
Enable Opening/Closings call directions for Phone 2
[367]
Zone Restorals
Zones
Alarm Restoral Reporting Codes
1-64
00
00
00
Section
00
00
00
00
00
[324]-[327]
00 = Disabled
DLS/Installer Lead IN/OUT
Miscellaneous Maintenance Reporting Codes
DEF
DEF
DEF
00
00
Section
DEF
DEF
DEF
DEF
DEF
00
DEF = No change to default values, 00 = Disabled
Digit 5 selects DLS connection options.
Option
1
2
3
Programming Section
DLS Connection/Call back setting
[401] Option 1 OFF
Option 3 OFF
[406] 0
Double Call Disabled, Call Back Disabled
[401] Option 1 ON
Option 3 OFF
[406] 9
Double Call Enabled, Call Back Disabled
[401] Option 1 ON
Option 3 ON
[406] 9
Double CallEenabled, Call Back Enabled
Number of rings to answer on set to 0
Number of rings to answer on set to 9
Number of rings to answer on set to 9
00
[347]
Note to Installers
Limited Warranty
This warning contains vital information. As the only individual in contact with system users, it is your
responsibility to bring each item in this warning to the attention of the users of this system.
Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of
purchase, the product shall be free of defects in materials and workmanship under normal use. During the
warranty period, Digital Security Controls shall, at its option, repair or replace any defective product upon
return of the product to its factory, at no charge for labour and materials. Any replacement and/or repaired
parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is longer. The
original purchaser must promptly notify Digital Security Controls in writing that there is defect in material
or workmanship, such written notice to be received in all events prior to expiration of the warranty period.
There is absolutely no warranty on software and all software products are sold as a user license under the
terms of the software license agreement included with the product. The Customer assumes all responsibility
for the proper selection, installation, operation and maintenance of any products purchased from DSC. Custom products are only warranted to the extent that they do not function upon delivery. In such cases, DSC
can replace or credit at its option.
System Fail ur es
This system has been carefully designed to be as effective as possible. There are circumstances, however,
involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons.
Some but not all of these reasons may be:
• Inadequate Installation
A security system must be installed properly in order to provide adequate protection. Every installation
should be evaluated by a security professional to ensure that all access points and areas are covered. Locks
and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings
and other building materials must be of sufficient strength and construction to provide the level of protection
expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire
and/or police department is highly recommended if this service is available.
• Criminal Knowledge
This system contains security features which were known to be effective at the time of manufacture. It is
possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected.
• Access by Intruders
International Warranty
The warranty for international customers is the same as for any customer within Canada and the United
States, with the exception that Digital Security Controls shall not be responsible for any customs fees, taxes,
or VAT that may be due.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All
authorized distributors and dealers have a warranty program. Anyone returning goods to Digital Security
Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment
whatsoever for which prior authorization has not been obtained.
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by
moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent
the proper operation of the system.
Conditions to Void Warranty
• Power Failure
• damage incurred in shipping or handling;
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate
power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail.
Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a
device operates only by AC power, any interruption, however brief, will render that device inoperative while
it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations
which may damage electronic equipment such as a security system. After a power interruption has occurred,
immediately conduct a complete system test to ensure that the system operates as intended.
• Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide several years of battery life under normal
conditions. The expected battery life is a function of the device environment, usage and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the
expected battery life. While each transmitting device has a low battery monitor which identifies when the
batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance
will keep the system in good operating condition.
• Compromise of Radio Frequency (Wireless) Devices
Signals may not reach the receiver under all circumstances which could include metal objects placed on or
near the radio path or deliberate jamming or other inadvertent radio signal interference.
• System Users
A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary
physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is
important that all system users be trained in the correct operation of the alarm system and that they know
how to respond when the system indicates an alarm.
• Smoke Detectors
Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke
may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the
other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence or building.
Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot
sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by
carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of
flammable materials, overloaded electrical circuits, children playing with matches or arson.
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient
warning to allow all occupants to escape in time to avoid injury or death.
• Motion Detectors
Motion detectors can only detect motion within the designated areas as shown in their respective installation
instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not
provide volumetric area protection. They have multiple beams of detection and motion can only be detected
in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors,
windows or any other part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness
can be reduced when the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be
heaters, radiators, stoves, barbecues, fireplaces, sunlight, steam vents, lighting and so on.
• Warning Devices
Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if
there is an intervening wall or door. If warning devices are located on a different level of the residence or
premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may
be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired
person.
• Telephone Lines
If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time.
Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may
be difficult to detect.
This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:
• damage caused by disaster such as fire, flood, wind, earthquake or lightning;
• damage due to causes beyond the control of Digital Security Controls such as excessive voltage,
mechanical shock or water damage;
• damage caused by unauthorized attachment, alterations, modifications or foreign objects;
• damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls
Ltd.);
• defects caused by failure to provide a suitable installation environment for the products;
• damage caused by use of the products for purposes other than those for which it was designed;
• damage from improper maintenance;
• damage arising out of any other abuse, mishandling or improper application of the products.
Items Not Covered by Warranty
In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i)
freight cost to the repair centre; (ii) products which are not identified with DSC's product label and lot number or serial number; (iii) products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned
for replacement under warranty will be credited or replaced at DSC's option. Products not covered by this
warranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair estimate shall be provided. No repair work will be performed until a valid purchase order is received from the
Customer and a Return Merchandise Authorization number (RMA) is issued by DSC's Customer Service.
Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reasonable number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach
of warranty. Under no circumstances shall Digital Security Controls be liable for any special, incidental, or
consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any
other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any
associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services,
down time, purchaser’s time, the claims of third parties, including customers, and injury to property. The
laws of some jurisdictions limit or do not allow the disclaimer of consequential damages. If the laws of such
a jurisdiction apply to any claim by or against DSC, the limitations and disclaimers contained here shall be
to the greatest extent permitted by law. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so that the above may not apply to you.
Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether
expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose)
and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls
neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify
or to change this warranty, nor to assume for it any other warranty or liability concerning this product. This
disclaimer of warranties and limited warranty are governed by the laws of the province of Ontario, Canada.
WARNING: Digital Security Controls recommends that the entire system be completely
tested on a regular basis. However, despite frequent testing, and due to, but not limited to,
criminal tampering or electrical disruption, it is possible for this product to fail to perform as
expected.
• Insufficient Time
Out of Warranty Repairs
There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the emergency due to their inability to respond to the warnings in a timely manner. If the system
is monitored, the response may not occur in time to protect the occupants or their belongings.
Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to
its factory according to the following conditions. Anyone returning goods to Digital Security Controls must
first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for
which prior authorization has not been obtained.
• Component Failure
Although every effort has been made to make this system as reliable as possible, the system may fail to
function as intended due to the failure of a component.
• Inadequate Testing
Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested weekly and immediately after a break-in, an
attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or
outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating
devices and any other operational devices that are part of the system.
• Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or
minimize the harmful effects of an emergency situation.
Products which Digital Security Controls determines to be repairable will be repaired and returned. A set fee
which Digital Security Controls has predetermined and which may be revised from time to time, will be
charged for each unit repaired.
Products which Digital Security Controls determines not to be repairable will be replaced by the nearest
equivalent product available at that time. The current market price of the replacement product will be
charged for each replacement unit.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls
could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to Identify and
Resolve Radio/Television Interference Problems". This booklet is available from the U.S.
Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a
label that contains, among other information, the FCC registration number and ringer
equivalence number (REN) for this equipment. If requested, this number must be provided
to the Telephone Company.
PC1864 Product Identifier
US: F53AL01BPC1864
PC1832 Product Identifier
US: F53AL01BPC1832
PC1616 Product Identifier
US: F53AL01BPC1614
REN:
0.1B
USOC Jack:
RJ-31X
Company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment PC1616, PC1832, PC1864 for repair or warranty information, please contact the facility indicated below. If the equipment is causing
harm to the telephone network, the Telephone Company may request that you disconnect
the equipment until the problem is solved. This equipment is of a type that is not intended
to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
Alarm dialling equipment must be able to seize the telephone line and place a call in an
emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm
dialling equipment must be connected to a properly installed RJ-31X jack that is electrically
in series with and ahead of all other equipment attached to the same telephone line. Proper
installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.
Customer Premises Equipment and Wiring
Network
Service
Provider's
Facilities
Computer
RJ-31X
Jack
Alarm Dialing
Equipment
Unused
RJ-11 Jack
Telephone
Line
Telephone
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the
ACTA. A compliant telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone
line. Excessive RENs on a telephone line may result in the devices not ringing in response to
an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact
the local Telephone Company. For products approved after July 23, 2001, the REN for this
product is part of the product identifier that has the format.
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm
If this equipment PC1864/PC1832/PC1616 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may
be required. But if advance notice is not practical, the Telephone Company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint with
the FCC if you believe it is necessary.
Network
Demarcation
Point
Fax Machine
Telephone
Answering
System
Unused
RJ-11 Jack
Telephone
INDUSTRY CANADA STATEMENT
NOTICE: This Equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration
of Conformity indicating that Industry Canada technical specifications were met. It does not
imply that that Industry Canada approved the equipment
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The
REN assigned to each terminal equipment provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination on an interface
may consist of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all devices does not exceed five.
PC1616 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1614
PC1832 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1832
PC1864 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1864
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone
© 2007, Digital Security Controls
Tech Support: 1-800-387-3630 (Canada & U.S.) or 905-760-3036
Printed in Canada . • www.dsc.com
29007359R003
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising